ALBERT

Description: Energies, Vol. 11, Pages 44: Transient Stability Analysis of Islanded AC Microgrids with a Significant Share of Virtual Synchronous Generators Energies doi: 10.3390/en11010044 Authors: Chang Yuan Peilin Xie Dan Yang Xiangning Xiao As an advanced control method that could bring extra inertia and damping characteristics to inverter-based distributed generators, the virtual synchronous generator (VSG) has recently drawn considerable attention. VSGs are expected to enhance the frequency regulation capability of the local power grid, especially the AC microgrid in island mode. However, the cost of that performance promotion is potential instability. In this paper, the unstable phenomena of the islanded microgrid dominated by SGs and distributed generators (DSs) are addressed after mathematical modeling and detailed eigenvalue analyses respectively. The influence of VSG key parameters, e.g., virtual inertia, damping factor, and droop coefficient on system stability is investigated, and the corresponding mathematical calculation method of unstable region is obtained. The theoretical analysis is well supported by time domain simulation results. The predicted frequency oscillation suggests the consideration of stability constrain during the VSG parameters design procedure.

Description: Energies, Vol. 11, Pages 77: Anisotropy in Thermal Recovery of Oil Shale—Part 1: Thermal Conductivity, Wave Velocity and Crack Propagation Energies doi: 10.3390/en11010077 Authors: Guoying Wang Dong Yang Zhiqin Kang Jing Zhao In this paper, the evolution of thermal conductivity, wave velocity and microscopic crack propagation both parallel and perpendicular to the bedding plane in anisotropic rock oil shale were studied at temperatures ranging from room temperature to 600 °C. The results show that the thermal conductivity of the perpendicular to bedding direction (KPER) (PER: perpendicular to beeding direction), wave velocity of perpendicular to bedding diretion (VPER), thermal conduction coefficient of parallel to beeding direction (KPAR) and wave velocity of parallel to beeding direction (VPAR) (PAR: parallel to bedding direction) decreased with the increase in temperature, but the rates are different. KPER and VPER linearly decreased with increasing temperature from room temperature to 350 °C, with an obvious decrease at 400 °C corresponding to a large number of cracks generated along the bedding direction. KPER, VPER, KPAR and VPAR generally maintained fixed values from 500 °C to 600 °C. 400 °C has been identified as the threshold temperature for anisotropic evolution of oil shale thermal physics. In addition, the relationship between the thermal conductivity and wave velocity based on the anisotropy of oil shale was fitted using linear regression. The research in this paper can provide reference for the efficient thermal recovery of oil shale, thermal recovery of heavy oil reservoirs and the thermodynamic engineering in other sedimentary rocks.

Description: Energies, Vol. 11, Pages 64: Practical On-Board Measurement of Lithium Ion Battery Impedance Based on Distributed Voltage and Current Sampling Energies doi: 10.3390/en11010064 Authors: Xuezhe Wei Xueyuan Wang Haifeng Dai Battery impedance based state estimation methods receive extensive attention due to its close relation to internal dynamic processes and the mechanism of a battery. In order to provide impedance for a battery management system (BMS), a practical on-board impedance measuring method based on distributed signal sampling is proposed and implemented. Battery cell perturbing current and its response voltage for impedance calculation are sampled separately to be compatible with BMS. A digital dual-channel orthogonal lock-in amplifier is used to calculate the impedance. With the signal synchronization, the battery impedance is obtained and compensated. And the relative impedance can also be obtained without knowing the current. For verification, an impedance measuring system made up of electronic units sampling and processing signals and a DC-AC converter generating AC perturbing current is designed. A type of 8 Ah LiFePO4 battery is chosen and the valuable frequency range for state estimations is determined with a series of experiments. The battery cells are connected in series and the impedance is measured with the prototype. It is shown that the measurement error of the impedance modulus at 0.1 Hz–500 Hz at 5 °C–35 °C is less than 4.5% and the impedance phase error is less than 3% at <10 Hz at room temperature. In addition, the relative impedance can also be tracked well with the designed system.

Description: Energies, Vol. 11, Pages 80: Well Test Analysis for Fractured and Vuggy Carbonate Reservoirs of Well Drilling in Large Scale Cave Energies doi: 10.3390/en11010080 Authors: Cuiqiao Xing Hongjun Yin Kexin Liu Xingke Li Jing Fu A well test analysis model for fractured and vuggy carbonate reservoir of wells drilling in large scale cave considering wellbore storage and skin factor is established in this paper. The Laplace transformation and Stehfest numerical inversion are applied to obtain the results of wellbore pressure. Through the sensitivity analysis of different parameters for the well test typical curves, it is found that the change of the well test curves is in accordance with the theoretical analysis. With the increase of skin factor, the hump of well test typical curves is steeper. The storage ratio influences the depth and width of the concave in the pressure derivative curves. The cross flow coefficient mainly affects the position of the concave occurrence in the pressure derivative curves. The dimensionless reservoir radius mainly affects the middle and late stages of the log-log pressure type curves, and the later well test curves will be upturned for sealed boundary. The duration of the early stage of the log-log curves will become longer when drilling in large scale cave. The effective well radius is increased to a certain extent, which is in full agreement with the conclusions in this paper. The size of the caves has the same effect on the well test typical curves as wellbore storage coefficient. Due to acidification, fracturing, and other reasons, the boundary of the cave will collapse. Therefore, considering the wellbore storage coefficient and skin effect is very important during well testing. However, the existing models for well testing of fractured and vuggy carbonate reservoir often ignore the wellbore storage coefficient and skin effect. For fractured and vuggy carbonate reservoirs of well drilling in large scale cave, the existing models are not applicable. Since the previous models are mostly based on the triple-porosity medium and the equivalent continuum. The well test model for well drilling in large scale cave of fracture-cavity carbonate reservoirs with wellbore storage coefficient and skin factor in this work has significant application value for oil field.

Description: Energies, Vol. 11, Pages 32: High-Precision Speed Control Based on Multiple Phase-Shift Resonant Controllers for Gimbal System in MSCMG Energies doi: 10.3390/en11010032 Authors: Jian Feng Qing Wang Kun Liu The high precision speed control of gimbal servo system in magnetically suspended control moment gyro (MSCMG) suffers from periodic torque disturbances, which lead to periodic fluctuations in speed control. This paper proposes a novel multiple phase-shift resonant controller (MPRC) for a gimbal servo system to suppress the periodic torque ripples whose frequencies vary with the operational speed of the gimbal servo motor and high-speed motor. First, the periodic torque ripples caused by cogging torque, flux harmonics and the dynamic unbalance of the high speed rotor are analyzed. Second, the principle and structure of MPRC parallel with proportional integral (PI) controllers are discussed. The design and stability analysis of the proposed MPRC plus PI control scheme are given both for the current loop and speed loop. The closed-loop stability is ensured by adjusting the phase in the entire operational speed range. Finally, the effectiveness of the proposed control method is verified through simulation and experimental results.

Description: Sustainability, Vol. 10, Pages 2593: Visual Analysis of the Height Ratio between Building and Background Vegetation. Two Rural Cases of Study: Spain and Sweden Sustainability doi: 10.3390/su10082593 Authors: Jacinto Garrido-Velarde María Jesús Montero-Parejo Julio Hernández-Blanco Lorenzo García-Moruno The perception of apparent sizes of buildings in a rural environment depends on the height ratio between the building and its surrounding vegetation, and it is this parameter which is currently used to assess the built landscapes. The impact of a contrasting height is less strong if the building does not exceed the horizon line. For buildings overshooting the skyline, the building’s level of sharpness and number of lines in contrast to the sky determines the impact of the scales, and vegetation in the background helps to reduce impact. The specific objectives of the present study were: (1) finding height–ratio thresholds between building and background vegetation, which may improve the integration of rural buildings in sky-sensitive locations, and; (2) comparing the results in two rural contexts with very different climatic conditions: Spain and Sweden. A survey of eighteen scenarios (nine Spanish and nine Swedish), all digitally modified with different relative height ratios between vegetation and buildings, was performed. The survey was evaluated by the public from both countries. Regardless of the country of origin, integration of the building was good or very good when the vegetation in background did not exceed one half of the height of the construction. These results may be translated to technical criteria for planning assessment.

Description: Sensors, Vol. 18, Pages 2406: Adaptive Robust Unscented Kalman Filter via Fading Factor and Maximum Correntropy Criterion Sensors doi: 10.3390/s18082406 Authors: Zhihong Deng Lijian Yin Baoyu Huo Yuanqing Xia In most practical applications, the tracking process needs to update the data constantly. However, outliers may occur frequently in the process of sensors’ data collection and sending, which affects the performance of the system state estimate. In order to suppress the impact of observation outliers in the process of target tracking, a novel filtering algorithm, namely a robust adaptive unscented Kalman filter, is proposed. The cost function of the proposed filtering algorithm is derived based on fading factor and maximum correntropy criterion. In this paper, the derivations of cost function and fading factor are given in detail, which enables the proposed algorithm to be robust. Finally, the simulation results show that the presented algorithm has good performance, and it improves the robustness of a general unscented Kalman filter and solves the problem of outliers in system.

Description: Sustainability, Vol. 10, Pages 2586: Conserving Tropical Forests: Can Sustainable Livelihoods Outperform Artisanal or Informal Mining? Sustainability doi: 10.3390/su10082586 Authors: Joshua Fisher Poonam Arora Sophia Rhee The viability of conservation efforts, including protected areas and buffer zones, depends on finding ways to make those strategies more attractive and viable for local populations. This paper presents a pilot study utilizing a rapid rural appraisal of livelihoods in the buffer zone of Tambopata National Reserve in Madre de Dios, Peru, threatened by illegal gold mining and logging. We evaluated three predominant economic activities—artisanal gold mining, Brazil nut harvesting, and fish farming—in terms of potential economic returns. The main research question we ask is whether the latter two potentially sustainable land uses can match or exceed the returns from mining. Contrary to popular belief, we find that enhancing value creation at product origin could make existing forest-friendly livelihoods as or more lucrative than extractive ones. This has implications on local conservation policy encouraging implementable strategies incentivizing sustainable livelihoods in tandem with, and in support of, conservation goals.

Description: Sustainability, Vol. 10, Pages 2601: Researcher–Planner Dialogue on Environmental Justice and Its Knowledges—A Means to Encourage Social Learning Towards Sustainability Sustainability doi: 10.3390/su10082601 Authors: Aino Rekola Riikka Paloniemi Societies aiming for a sustainable future need more effective and legitimate planning and decision making practices, in which various actors together find pathways towards a sustainable transition. In this paper, we approach sustainability and environmental justice as epistemological (and ontological) challenges for land-use planning, and empirically analyse how action research could support planners’ social learning and planning towards fair and sustainable development. We analysed qualitatively the evolution of the researcher–planner dialogue while co-designing and developing better methods, means and practices to improve environmental justice in regional scale planning in Kymenlaakso Region, South-East Finland. We found that researcher-planner dialogue developed during cooperation. While in the beginning, social learning related to approaching environmental justice as a fair distribution of power evolved incrementally, later, when dialogue became more focused, communicative and reflective as an outcome of mutual frames and trust, learning occurred in a more transformative way. Such transformative learning concerned recognising youth as a silent group in the planning process and the means to involve their perceptions in planning. In order to support sustainability transformation in the future, we conclude that it is essential to create opportunities for such incremental and transformative social learning through innovative modes of interaction in various contexts.

Description: Sustainability, Vol. 10, Pages 2602: Towards a Joint Local Energy Transition Process in Urban Districts: The GO2Zero Simulation Game Sustainability doi: 10.3390/su10082602 Authors: Geertje Bekebrede Ellen van Bueren Ivo Wenzler The depletion of fossil fuel sources for our energy system and the influence on overall CO2 emissions drive the need to more sustainable energy systems. The transition towards a renewable energy system cannot be seen as a purely technical issue; it is strongly embedded within society. In this study, we analyze the stakeholder complexities of the transition in urban districts and research the use of a simulation game to increase the understanding of the complexity of the transition. Surveys and observations were used to collect data about the learning experiences of playing the game GO2Zero. The results show that participants liked to play the game and they considered the game a valid representation of the system. Further, the participants agree that they obtained a better understanding of the complexity of the residential energy system and experienced a variety of challenges in the transition. Simulation games, like GO2Zero, could become valuable instruments in local energy transition processes as they offer a safe environment for novices and experts to jointly experiment with the challenges in this process. These experiences could support the design of the transition process by helping actors to formulate goals and collaborative strategies for achieving those goals. Future research will focus on the use of this game for experimenting with different strategies and instruments and to analyze their effects.

Description: Energies, Vol. 11, Pages 1937: Evaluation of Fast Charging Efficiency under Extreme Temperatures Energies doi: 10.3390/en11081937 Authors: Germana Trentadue Alexandre Lucas Marcos Otura Konstantinos Pliakostathis Marco Zanni Harald Scholz Multi-type fast charging stations are being deployed over Europe as electric vehicle adoption becomes more popular. The growth of an electrical charging infrastructure in different countries poses different challenges related to its installation. One of these challenges is related to weather conditions that are extremely heterogeneous due to different latitudes, in which fast charging stations are located and whose impact on the charging performance is often neglected or unknown. The present study focused on the evaluation of the electric vehicle (EV) charging process with fast charging devices (up to 50 kW) at ambient (25 °C) and at extreme temperatures (−25 °C, −15 °C, +40 °C). A sample of seven fast chargers and two electric vehicles (CCS (combined charging system) and CHAdeMO (CHArge de Move)) available on the commercial market was considered in the study. Three phase voltages and currents at the wall socket, where the charger was connected, as well as voltage and current at the plug connection between the charger and vehicle have been recorded. According to SAE (Society of Automotive Engineers) J2894/1, the power conversion efficiency during the charging process has been calculated as the ratio between the instantaneous DC power delivered to the vehicle and the instantaneous AC power supplied from the grid in order to test the performance of the charger. The inverse of the efficiency of the charging process, i.e., a kind of energy return ratio (ERR), has been calculated as the ratio between the AC energy supplied by the grid to the electric vehicle supply equipment (EVSE) and the energy delivered to the vehicle’s battery. The evaluation has shown a varied scenario, confirming the efficiency values declared by the manufacturers at ambient temperature and reporting lower energy efficiencies at extreme temperatures, due to lower requested and, thus, delivered power levels. The lowest and highest power conversion efficiencies of 39% and 93% were observed at −25 °C and ambient temperature (+25 °C), respectively.

Description: Energies, Vol. 11, Pages 1934: Multi-Port Zero-Current Switching Switched-Capacitor Converters for Battery Management Applications Energies doi: 10.3390/en11081934 Authors: Yat Chi Fong Ka Wai Eric Cheng S. Raghu Raman Xiaolin Wang A novel implementation of multi-port zero-current switching (ZCS) switched-capacitor (SC) converters for battery management applications is presented. In addition to the auto-balancing feature offered by the SC technique, the proposed SC converter permits individual control of the charging or discharging current of the series-connected energy storage elements, such as the battery or super-capacitor cells. This approach enables advanced state control and accelerates the equalizing process by coordinated operation with the battery management system (BMS) and an adjustable voltage source, which can be implemented by a DC-DC converter interfaced to the energy storage string. Different configurations, including the single-input multi-output (SIMO), multi-input single-output (MISO) SC converters, and the corresponding altered circuits for string-to-cells, cells-to-string, as well as cells-to-cells equalizers, are discussed with a circuit analysis and derivation of the associated mathematical representation. The simulation study and experimental results indicated a significant increase in the balancing speed with the presence of BMS and closed-loop control of cell currents.

Description: Sensors, Vol. 18, Pages 2420: Strain Transfer Characteristics of Resistance Strain-Type Transducer Using Elastic-Mechanical Shear Lag Theory Sensors doi: 10.3390/s18082420 Authors: Yongqian Li Zhigang Wang Chi Xiao Yinming Zhao Yaxin Zhu Zili Zhou The strain transfer characteristics of resistance strain gauge are theoretically investigated. A resistance strain-type transducer is modeled to be a four-layer and two-glue (FLTG) structure model, which comprises successively the surface of an elastomer sensitive element, a ground adhesive glue, a film substrate layer, an upper adhesive glue, a sensitive grids layer, and a polymer cover. The FLTG model is studied in elastic–mechanical shear lag theory, and the strain transfer progress in a resistance strain-type transducer is described. The strain transitional zone (STZ) is defined and the strain transfer ratio (STR) of the FLTG structure is formulated. The dependences of the STR and STZ on both the dimensional sizes of the adhesive glue and structural parameters are calculated. The results indicate that the width, thickness and shear modulus of the ground adhesive glue have a greater influence on the STZ ratio. To ensure that the resistance strain gauge has excellent strain transfer performance and low hysteresis, it is recommended that the paste thickness should be strictly controlled, and the STZ ratio should be less than 10%. Moreover, the STR strongly depends on the length and width of the sensitive grids.

Description: Sensors, Vol. 18, Pages 2416: Design and Optimization of a Novel Three-Dimensional Force Sensor with Parallel Structure Sensors doi: 10.3390/s18082416 Authors: Guanyu Huang Dan Zhang Sheng Guo Haibo Qu To measure large external forces exerted on a loading platform, a novel three-dimensional force sensor is developed in this paper. The proposed sensor was designed with a parallel mechanism with three degrees of freedom. Kinematic analysis of this sensor was performed. Due to its structural characteristics, the working principle of the sensor was analyzed using a Jacobian matrix. The sensitivity diversity index and measuring capability were both calculated. The analysis showed that the proposed sensor is more suitable for measuring large forces than existing strain sensors. In addition, compared with existing strain sensors, this sensor is more suitable for measuring forces along the x and y axes. By changing the stiffness coefficients of the springs, the proposed sensor has reconfigurability. This sensor can change its measuring capability to meet different requirements. Next, the mode shapes and natural frequencies of the proposed sensor were performed. Finally, based on these performance indices, the design variables were optimized using a Multi-Objective Genetic Algorithm.

Description: Sensors, Vol. 18, Pages 2415: Cheeses Made from Raw and Pasteurized Cow’s Milk Analysed by an Electronic Nose and an Electronic Tongue Sensors doi: 10.3390/s18082415 Authors: Nuno I. P. Valente Alisa Rudnitskaya João A. B. P. Oliveira M. Teresa S. R. Gomes Elvira M. M. Gaspar Cheese prepared from whole milk, raw and pasteurized, were analysed by an electronic nose based on piezoelectric quartz crystals and an electronic tongue based on potentiometric sensors, immediately after their preparation and along ripening (after 7 and 21 days). Whey was also analysed by the potentiometric electronic tongue. Results obtained by the electronic nose and tongue were found to be complementary, with the electronic nose being more sensitive to differences in the milk and the electronic tongue being more sensitive to milk pasteurization. Electronic tongue was able to distinguish cheeses made from raw and pasteurized milk, both analysing the whey or the curd, with correct classification rate of 96% and 84%, respectively. Besides, the electronic nose was more sensitive than the electronic tongue to the ripening process, with large differences between samples after 7 and 21 days, while the electronic tongue was only sensitive to the initial maturation stages, with large difference between freshly prepared cheese and with seven days of maturation.

Description: Sensors, Vol. 18, Pages 2412: Validation of the Accuracy and Convergence Time of Real Time Kinematic Results Using a Single Galileo Navigation System Sensors doi: 10.3390/s18082412 Authors: Zbigniew Siejka For the last two decades, the American GPS and Russian GLONASS were the basic systems used in global positioning and navigation. In recent years, there has been significant progress in the development of positioning systems. New regional systems have been created, i.e., the Japanese Quasi-Zenith Satellite System (QZSS) and Indian Regional Navigational Satellite System (IRNSS). A plan to build its own regional navigation system named Korean Positioning System (KPS) was announced South Korea on 5 February 2018. Currently, two new global navigation systems are under development: the European Galileo and the Chinese BeiDou. The full operability of both systems by 2020 is planned. The paper deals with a possibility of determination of the user’s position from individual and independent global navigation satellite system (GNSS). The article is a broader concept aimed at independent determination of precise position from individual GPS, GLONASS, BeiDou and Galileo systems. It presents real time positioning results (Real Time Kinematic-RTK) using signals from Galileo satellites only. During the test, 14 Galileo satellites were used and the number of simultaneously observed Galileo satellites varied from five to seven. Real-time measurements were only possible in certain 24-h observation windows. However, their number was completed within 6 days at the end of 2017 and beginning of 2018, so there was possible to infer about the current availability, continuity, convergence time and accuracy of the RTK measurements. In addition, the systematic errors were demonstrated for the Galileo system.

Description: Sustainability, Vol. 10, Pages 2613: An E-Commerce Platform for Industrialized Construction Procurement Based on BIM and Linked Data Sustainability doi: 10.3390/su10082613 Authors: Dandan He Zhongfu Li Chunlin Wu Xin Ning Industrialized construction has raised the requirements of procurement methods used in the construction industry. The rapid development of e-commerce offers efficient and effective solutions, however the large number of participants in the construction industry means that the data involved are complex, and problems arise related to volume, heterogeneity, and fragmentation. Thus, the sector lags behind others in the adoption of e-commerce. In particular, data integration has become a barrier preventing further development. Traditional e-commerce platform, which considered data integration for common product data, cannot meet the requirements of construction product data integration. This study aimed to build an information-integrated e-commerce platform for industrialized construction procurement (ICP) to overcome some of the shortcomings existing platforms. We proposed a platform based on Building Information Modelling (BIM) and linked data, taking an innovative approach to data integration. It uses industrialized construction technology to support product standardization, BIM to support procurement process, and linked data to connect different data sources. The platform was validated using a case study. With the development of an e-commerce ontology, industrialized construction component information was extracted from BIM models and converted to Resource Description Framework (RDF) format. Related information from different data sources was also converted to RDF format, and Simple Protocol and Resource Description Framework Query Language (SPARQL) queries were implemented. The platform provides a solution for the development of e-commerce platform in the construction industry.

Description: Sustainability, Vol. 10, Pages 2614: An Efficient Grid-Based K-Prototypes Algorithm for Sustainable Decision-Making on Spatial Objects Sustainability doi: 10.3390/su10082614 Authors: Hong-Jun Jang Byoungwook Kim Jongwan Kim Soon-Young Jung Data mining plays a critical role in sustainable decision-making. Although the k-prototypes algorithm is one of the best-known algorithms for clustering both numeric and categorical data, clustering a large number of spatial objects with mixed numeric and categorical attributes is still inefficient due to complexity. In this paper, we propose an efficient grid-based k-prototypes algorithm, GK-prototypes, which achieves high performance for clustering spatial objects. The first proposed algorithm utilizes both maximum and minimum distance between cluster centers and a cell, which can reduce unnecessary distance calculation. The second proposed algorithm as an extension of the first proposed algorithm, utilizes spatial dependence; spatial data tends to be similar to objects that are close. Each cell has a bitmap index which stores the categorical values of all objects within the same cell for each attribute. This bitmap index can improve performance if the categorical data is skewed. Experimental results show that the proposed algorithms can achieve better performance than the existing pruning techniques of the k-prototypes algorithm.

Description: Sustainability, Vol. 10, Pages 2609: The Influence of the Backfilling Roadway Driving Sequence on the Rockburst Risk of a Coal Pillar Based on an Energy Density Criterion Sustainability doi: 10.3390/su10082609 Authors: Yi Xue Zhengzheng Cao Feng Du Lin Zhu The rockburst hazard has always been an important issue affecting the safety production of coal mines in China. The unreasonable sequencing of roadway driving can lead to the dynamic instability of coal pillars, which subsequently causes rockburst accidents in roadway backfilling mining engineering and poses a serious threat to the safety of the mines. Roadway backfilling mining technology is an effective approach with which to mine corner residual coal resources under buildings, railways, and rivers. An energy density criterion is established and programmed with FISH language using numerical analysis software for the rockburst risk evaluation of coal pillars. On this basis, a numerical simulation model is established based on four scheme types, namely, the sequential mining, one-roadway interval mining, two-roadway interval mining, and three-roadway interval mining schemes. The influence of the backfilling roadway driving sequence on coal pillar stability is investigated, and the change law of vertical stress and energy density factor of coal pillars in different driving sequences in roadway backfilling mining technology are analyzed. According to the research results, the maximum energy density factor value of 21,172 J/m4 for coal pillars in one-roadway interval mining is the lowest among the different schemes. Therefore, the one-roadway interval mining scheme is the optimal choice in roadway backfilling mining technology. The results can be treated as an important basis for the prevention and treatment of coal pillar instability and rockburst in roadway backfilling mining technology.

Description: Sensors, Vol. 18, Pages 2409: The Bluetooth Mesh Standard: An Overview and Experimental Evaluation Sensors doi: 10.3390/s18082409 Authors: Mathias Baert Jen Rossey Adnan Shahid Jeroen Hoebeke Mesh networks enable a many-to-many relation between nodes, which means that each node in the network can communicate with every other node using multi-hop communication and path diversity. As it enables the fast roll-out of sensor and actuator networks, it is an important aspect within the Internet of Things (IoT). Utilizing Bluetooth Low Energy (BLE) as an underlying technology to implement such mesh networks has gained a lot of interest in recent years. The result was a variety of BLE meshing solutions that were not interoperable because of the lack of a common standard. This has changed recently with the advent of the Bluetooth Mesh standard. However, a detailed overview of how this standard operates, performs and how it tackles other issues concerning BLE mesh networking is missing. Therefore, this paper investigates this new technology thoroughly and evaluates its performance by means of three approaches, namely an experimental evaluation, a statistical approach and a graph-based simulation model, which can be used as the basis for future research. Apart from showing that consistent results are achieved by means of all three approaches, we also identify possible drawbacks and open issues that need to be dealt with.

Description: Sustainability, Vol. 10, Pages 2604: Analysis of Guidelines and Identification of Characteristics Influencing the Deconstruction Potential of Buildings Sustainability doi: 10.3390/su10082604 Authors: Roberta Carvalho Machado Henor Artur de Souza Gustavo de Souza Veríssimo Growing concerns regarding environmental preservation and the fact that the construction industry is one of the sectors with the highest rates of resource consumption and waste generation, have encouraged the adoption of deconstruction as an alternative to the demolition of buildings at the end of their lifecycle. However, the choice of strategies to enable deconstruction requires an in-depth knowledge of how the building’s characteristics, combined with the procedures adopted in the deconstruction process, will affect the reutilization of materials and components. In this paper, characteristics relating to design for deconstruction (DfD) are identified and the influence of each characteristic on the viability of a deconstruction is analysed. A literature review is conducted to assess the guideline of DfD and to identify relevant characteristics. These characteristics are then divided into the following categories: direct influence enabling deconstruction; influence on the ease of the process; and, influence on prolonging a building’s lifecycle. A number of questions are suggested for analysing each characteristic, and these can be employed in the development of a methodology for evaluating a building’s deconstruction potential. The identification of characteristics involved in the deconstruction guidelines may assist in the optimization of projects and the planning of deconstruction processes.

Description: Sustainability, Vol. 10, Pages 2605: Building a More Sustainable Society? A Case Study on the Role of Sustainable Development in the Education and Early Career of Water and Environmental Engineers Sustainability doi: 10.3390/su10082605 Authors: Anu Vehmaa Meeri Karvinen Marko Keskinen Engineering education is critical for sustainability, given the key role that engineers have in shaping the development of our society. Yet, engineering studies have traditionally not been driven by sustainability-related knowledge and skills, but focused more on general computational skills and technical problem-solving. This has also been the case in our case study, which focuses on recent water and environmental engineering graduates in Finland. We studied the role that sustainable development has had in their education and early career through an extensive questionnaire and semi-structured interviews. The analysis was done in two ways: indirectly by comparing how well the key working life knowledge and skills recognized by the respondents correspond with sustainability-related skills, and directly by studying the graduates’ views towards the sustainable development and their possibilities to advance it in their work. The results show that although sustainability was not at the core of respondents’ studies, their key competencies correspond well with sustainability-related working life skills. The respondents also see that sustainable development has a central role in water and environmental engineering, although it is typically more visible at a strategic rather than a practical level. However, the results also indicate that several early-career engineers have deficient knowledge of sustainable development, and are therefore lacking the ability to fully connect the principles of sustainable development into their own expertise. Overall, the findings suggest that water and environmental engineers with their wide set of competencies have the potential to take on a larger role in building a more sustainable society. To ensure this, engineering education should emphasize the connection between the field and sustainable development and clearly link engineers’ core competencies with the skills required to promote sustainability.

Description: Sustainability, Vol. 10, Pages 2603: Historic Urban Landscapes: A Review on Trends and Methodologies in the Urban Context of the 21st Century Sustainability doi: 10.3390/su10082603 Authors: Arturo Azpeitia Santander Agustín Azkarate Garai-Olaun Ander de la Fuente Arana This article makes a critical reflection, questioning the notion of historical urban landscapes as a conceptual paradigm used for the basis of urban conservation in the twenty-first century. The study begins with a brief summary of the origins and subsequent evolution of this concept, highlighting the two key reference milestones: the Vienna Memorandum (UNESCO, 2005) and the Paris Recommendation (UNESCO, 2011). Subsequently, the focus of attention will be on highlighting the problems and difficulties posed by the management and protection of historic urban landscapes today. In this sense, the focus of attention will be placed on the assumption that change is an inherent part of the urban condition, since there is no consensus on what the limits of acceptable change in historic urban landscapes should be. It also emphasizes three factors that make this more difficult: (1) the reminiscences of the doctrines of the Weberian administration in the current models of government; (2) the subjective nature of the systems of indicators applied to the scope of historic cities; and (3) the opportunism of tactical urbanism, which, despite its shortcomings, is becoming an outstanding alternative for the methodological development of the historic urban landscapes.

Description: Energies, Vol. 11, Pages 1947: Design, Operation, Modeling and Grid Integration of Power-to-Gas Bioelectrochemical Systems Energies doi: 10.3390/en11081947 Authors: Raúl Santiago Muñoz-Aguilar Daniele Molognoni Pau Bosch-Jimenez Eduard Borràs Mónica Della Pirriera Álvaro Luna This paper deals with the design, operation, modeling, and grid integration of bioelectrochemical systems (BES) for power-to-gas application, through an electromethanogenesis process. The paper objective is to show that BES-based power-to-gas energy storage is feasible on a large scale, showing a first approximation that goes from the BES design and operation to the electrical grid integration. It is the first study attempting to cover all aspects of a BES-based power-to-gas technology, on authors’ knowledge. Designed BES reactors were based on a modular architecture, suitable for a future scaling-up. They were operated in steady state for eight months, and continuously monitored in terms of power consumption, water treatment, and biomethane production, in order to obtain data for the following modeling activity. A black box linear model of the BES was computed by using least-square methods, and validated through comparison with collected experimental data. Afterwards, a BES stack was simulated through several series and parallel connections of reactors, in order to obtain higher power consumption and test the grid integration of a real application system. The renewable energy surplus and energy price variability were evaluated for the grid integration of the BES stack. The BES stack was then simulated as energy storage system during low energy price periods, and tested experimentally with a real time system.

Description: Energies, Vol. 11, Pages 1948: The Optimization of Hybrid Power Systems with Renewable Energy and Hydrogen Generation Energies doi: 10.3390/en11081948 Authors: Fu-Cheng Wang Yi-Shao Hsiao Yi-Zhe Yang This paper discusses the optimization of hybrid power systems, which consist of solar cells, wind turbines, fuel cells, hydrogen electrolysis, chemical hydrogen generation, and batteries. Because hybrid power systems have multiple energy sources and utilize different types of storage, we first developed a general hybrid power model using the Matlab/SimPowerSystemTM, and then tuned model parameters based on the experimental results. This model was subsequently applied to predict the responses of four different hybrid power systems for three typical loads, without conducting individual experiments. Furthermore, cost and reliability indexes were defined to evaluate system performance and to derive optimal system layouts. Finally, the impacts of hydrogen costs on system optimization was discussed. In the future, the developed method could be applied to design customized hybrid power systems.

Description: Energies, Vol. 11, Pages 1946: A Novel Multi-Population Based Chaotic JAYA Algorithm with Application in Solving Economic Load Dispatch Problems Energies doi: 10.3390/en11081946 Authors: Jiangtao Yu Chang-Hwan Kim Abdul Wadood Tahir Khurshiad Sang-Bong Rhee The economic load dispatch (ELD) problem is an optimization problem of minimizing the total fuel cost of generators while satisfying power balance constraints, operating capacity limits, ramp-rate limits and prohibited operating zones. In this paper, a novel multi-population based chaotic JAYA algorithm (MP-CJAYA) is proposed to solve the ELD problem by applying the multi-population method (MP) and chaotic optimization algorithm (COA) on the original JAYA algorithm to guarantee the best solution of the problem. MP-CJAYA is a modified version where the total population is divided into a certain number of sub-populations to control the exploration and exploitation rates, at the same time a chaos perturbation is implemented on each sub-population during every iteration to keep on searching for the global optima. The proposed MP-CJAYA has been adopted to ELD cases and the results obtained have been compared with other well-known algorithms reported in the literature. The comparisons have indicated that MP-CJAYA outperforms all the other algorithms, achieving the best performance in all the cases, which indicates that MP-CJAYA is a promising alternative approach for solving ELD problems.

Description: Energies, Vol. 11, Pages 1944: Prediction of Mud Pressures for the Stability of Wellbores Drilled in Transversely Isotropic Rocks Energies doi: 10.3390/en11081944 Authors: Chiara Deangeli Omoruyi Omoman Omwanghe Serious borehole instability problems are often related to the presence of weakness planes in rock formations. In this study, we investigated the stability of wellbores drilled along a principal direction and parallel to the weakness planes. We used three different strength criteria (weakness plane model, Hoek and Brown and Nova and Zaninetti) to calculate the mud pressures to avoid slip and tensile failure along the weakness planes. We identified the orientation of the weakness planes that generate the most critical slip condition as a function of the friction angle of the planes. We also identified the range of orientations of the weakness planes that corresponds with the lower mud pressure window. We confirmed the validity of the proposed relationships with comparative stability analyses by using analytical solutions and numerical simulations (Ubiquitous Joint Model, FLAC). We found that the mud pressures calculated with the Hoek and Brown criterion show a particular trend, which cannot be predicted by the weakness plane model. We provided two normalized stability charts to predict mud pressures to prevent slip along the weakness planes in the critical slip condition. Finally, we corroborated our findings by simulating the stability of wellbores drilled in the Pedernales Field (Venezuela) and in oil fields located in Bohai Bay (China).

Description: Energies, Vol. 11, Pages 1945: Baltic Power Systems’ Integration into the EU Market Coupling under Different Desynchronization Schemes: A Comparative Market Analysis Energies doi: 10.3390/en11081945 Authors: Ettore Bompard Shaghayegh Zalzar Tao Huang Arturs Purvins Marcelo Masera Currently, the power transmission system of the Baltic states is synchronized with the Integrated/Unified Power System (IPS/UPS), which includes the Russian grid, and the IPS/UPS provides frequency regulation and system security within the Baltic states. Since joining the European Union (EU) in 2004, the Baltic states have been following the EU’s energy policy targets. The Baltics are presently participating in a European electricity market, i.e., the NordPool market, while they are expected to join the pan-European electricity market—the European target model for power market integration. Moreover, from a power grid perspective, EU energy policies intend to desynchronize the power grid of the Baltic states from the IPS/UPS over the coming years. This paper evaluates these policy trends through market impacts, and it complements existing studies on Baltic-IPS/UPS desynchronization in terms of wholesale electricity prices, generation surpluses, primary reserve adequacy, and redispatch costs. Participation of the Baltic states in the integrated pan-European day-ahead electricity market with zonal pricing was modeled for 2030, followed by a national redispatch, with detailed power grid modeling of Baltic states to solve potential intrazonal congestion. The simulation results imply the superiority of the Baltics’ synchronization to continental Europe, compared to the other schemes.

Description: Energies, Vol. 11, Pages 1941: Assessment of Energetic, Economic and Environmental Performance of Ground-Coupled Heat Pumps Energies doi: 10.3390/en11081941 Authors: Matteo Rivoire Alessandro Casasso Bruno Piga Rajandrea Sethi Ground-coupled heat pumps (GCHPs) have a great potential for reducing the cost and climate change impact of building heating, cooling, and domestic hot water (DHW). The high installation cost is a major barrier to their diffusion but, under certain conditions (climate, building use, alternative fuels, etc.), the investment can be profitable in the long term. We present a comprehensive modeling study on GCHPs, performed with the dynamic energy simulation software TRNSYS, reproducing the operating conditions of three building types (residential, office, and hotel), with two insulation levels of the building envelope (poor/good), with the climate conditions of six European cities. Simulation results highlight the driving variables for heating/cooling peak loads and yearly demand, which are the input to assess economic performance and environmental benefits of GCHPs. We found that, in Italy, GCHPs are able to reduce CO2 emissions up to 216 g CO2/year per euro spent. However, payback times are still quite high, i.e., from 8 to 20 years. This performance can be improved by changing taxation on gas and electricity and using hybrid systems, adding a fossil-fuel boiler to cover peak heating loads, thus reducing the overall installation cost compared to full-load sized GCHP systems.

Description: Energies, Vol. 11, Pages 1940: The Selection of Wind Power Project Location in the Southeastern Corridor of Pakistan: A Factor Analysis, AHP, and Fuzzy-TOPSIS Application Energies doi: 10.3390/en11081940 Authors: Yasir Ahmed Solangi Qingmei Tan Muhammad Waris Ali Khan Nayyar Hussain Mirjat Ifzal Ahmed Pakistan has sufficient wind energy potential across various locations of the country. However, so far, wind energy development has not attained sufficient momentum matching its potential. Amongst various other challenges, the site selection for wind power development has always been a primary concern of the decision-makers. Principally, wind project site selection decisions are driven by various multifaceted criteria. As such, in this study, a robust research framework comprising of factor analysis (FA) of techno-economic and socio-political factors, and a hybrid analytical hierarchy process (AHP) and fuzzy technique for order of preference by similarity to ideal solution (FTOPSIS) have been used for the prioritization of sites in the southeastern region of Pakistan. The results of this study reveal economic and land acquisition as the most significant criteria and sub-criteria, respectively. From the eight different sites considered, Jamshoro has been prioritized as the most suitable location for wind project development followed by Hyderabad, Nooriabad, Gharo, Keti Bandar, Shahbandar, Sajawal, and Talhar. This study provides a comprehensive decision support framework comprising of FA and a hybrid AHP and Fuzzy TOPSIS for the systematic analysis to prioritize suitable sites for the wind project development in Pakistan.

Description: Energies, Vol. 11, Pages 1943: Impacts of Low-Carbon Fuel Standards in Transportation on the Electricity Market Energies doi: 10.3390/en11081943 Authors: Ahmad Karnama João Abel Peças Lopes Mauro Augusto da Rosa Electric Vehicles (EVs) are increasing the interdependence of transportation policies and the electricity market dimension. In this paper, an Electricity Market Model with Electric Vehicles (EMMEV) was developed, exploiting an agent-based model that analyzes how carbon reduction policy in transportation may increase the number of Electric Vehicles and how that would influence electricity price. Agents are Energy Service Providers (ESCOs) which can distribute fuels and their objective is to maximize their profit. In this paper, the EMMEV is used to analyze the impacts of the Low-Carbon Fuel Standard (LCFS), a performance-based policy instrument, on electricity prices and EV sales volume. The agents in EMMEV are regulated parties in LCFS should meet a certain Carbon Intensity (CI) target for their distributed fuel. In case they cannot meet the target, they should buy credits to compensate for their shortfall and if they exceed it, they can sell their excess. The results, considering the assumptions and limitations of the model, show that the banking strategy of the agents contributing in the LCFS might have negative impact on penetration of EVs, unless there is a regular Credit Clearance to trade credits. It is also shown that the electricity price, as a result of implementing the LCFS and increasing number of EVs, has increased between 2% and 3% depending on banking strategy.

Description: Sensors, Vol. 18, Pages 2436: Bio-Inspired Covert Active Sonar Strategy Sensors doi: 10.3390/s18082436 Authors: Jiajia Jiang Xianquan Wang Fajie Duan Chunyue Li Xiao Fu Tingting Huang Lingran Bu Ling Ma Zhongbo Sun The covertness of the active sonar is a very important issue and the sonar signal waveform design problem was studied to improve covertness of the system. Many marine mammals produce call pulses for communication and echolocation, and existing interception systems normally classify these biological signals as ocean noise and filter them out. Based on this, a bio-inspired covert active sonar strategy was proposed. The true, rather than man-made sperm whale, call pulses were used to serve as sonar waveforms so as to ensure the camouflage ability of sonar waveforms. A range and velocity measurement combination (RVMC) was designed by using two true sperm whale call pulses which had excellent range resolution (RR) and large Doppler tolerance (DT). The range and velocity estimation methods were developed based on the RVMC. In the sonar receiver, the correlation technology was used to confirm the start and end time of sonar signals and their echoes, and then based on the developed range and velocity estimation method, the range and velocity of the underwater target were obtained. Then, the RVMC was embedded into the true sperm whale call-train to improve the camouflage ability of the sonar signal-train. Finally, experiment results were provided to verify the performance of the proposed method.

Description: Sensors, Vol. 18, Pages 2435: Quantitative Contact-Less Estimation of Energy Expenditure from Video and 3D Imagery Sensors doi: 10.3390/s18082435 Authors: Gregor Koporec Goran Vučković Radoje Milić Janez Perš Measurement of energy expenditure is an important tool in sport science and medicine, especially when trying to estimate the extent and intensity of physical activity. However, most approaches still rely on sensors or markers, placed directly on the body. In this paper, we present a novel approach using a fully contact-less, fully automatic method, that relies on computer vision algorithms and widely available and inexpensive imaging sensors. We rely on the estimation of the optical and scene flow to calculate Histograms of Oriented Optical Flow (HOOF) descriptors, which we subsequently augment with the Histograms of Absolute Flow Amplitude (HAFA). Descriptors are fed into regression model, which allows us to estimate energy consumption, and to a lesser extent, the heart rate. Our method has been tested both in lab environment and in realistic conditions of a sport match. Results confirm that these energy expenditures could be derived from purely contact-less observations. The proposed method can be used with different modalities, including near infrared imagery, which extends its future potential.

Description: Sensors, Vol. 18, Pages 2434: Smart Portable Devices Suitable for Cultural Heritage: A Review Sensors doi: 10.3390/s18082434 Authors: Federica Valentini Andrea Calcaterra Simonetta Antonaroli Maurizio Talamo This article reviews recent portable sensor technologies to apply in the Cultural Heritage (CH) fields. The review has been prepared in the form of a retrospective description of the sensor’s history and technological evolution, having: new nanomaterials for transducers, miniaturized, portable and integrated sensors, the wireless transmission of the analytical signals, ICT_Information Communication Technology and IoT_Internet of Things to apply to the cultural heritage field. In addition, a new trend of movable tattoo sensors devices is discussed, referred to in situ analysis, which is especially important when scientists are in the presence of un-movable and un-tangible Cultural Heritage and Art Work objects. The new proposed portable contact sensors (directly applied to art work objects and surfaces) are non-invasive and non-destructive to the different materials and surfaces of which cultural heritage is composed.

Description: Sensors, Vol. 18, Pages 2433: Multi-Camera Imaging System for UAV Photogrammetry Sensors doi: 10.3390/s18082433 Authors: Damian Wierzbicki In the last few years, it has been possible to observe a considerable increase in the use of unmanned aerial vehicles (UAV) equipped with compact digital cameras for environment mapping. The next stage in the development of photogrammetry from low altitudes was the development of the imagery data from UAV oblique images. Imagery data was obtained from side-facing directions. As in professional photogrammetric systems, it is possible to record footprints of tree crowns and other forms of the natural environment. The use of a multi-camera system will significantly reduce one of the main UAV photogrammetry limitations (especially in the case of multirotor UAV) which is a reduction of the ground coverage area, while increasing the number of images, increasing the number of flight lines, and reducing the surface imaged during one flight. The approach proposed in this paper is based on using several head cameras to enhance the imaging geometry during one flight of UAV for mapping. As part of the research work, a multi-camera system consisting of several cameras was designed to increase the total Field of View (FOV). Thanks to this, it will be possible to increase the ground coverage area and to acquire image data effectively. The acquired images will be mosaicked in order to limit the total number of images for the mapped area. As part of the research, a set of cameras was calibrated to determine the interior orientation parameters (IOPs). Next, the method of image alignment using the feature image matching algorithms was presented. In the proposed approach, the images are combined in such a way that the final image has a joint centre of projections of component images. The experimental results showed that the proposed solution was reliable and accurate for the mapping purpose. The paper also presents the effectiveness of existing transformation models for images with a large coverage subjected to initial geometric correction due to the influence of distortion.

Description: Sensors, Vol. 18, Pages 2432: A Terahertz CMOS V-Shaped Patch Antenna with Defected Ground Structure Sensors doi: 10.3390/s18082432 Authors: Hyeongjin Kim Wonseok Choe Jinho Jeong In this paper, a V-shaped patch antenna with defected ground structure is proposed at terahertz to overcome the limited performance of a standard complementary metal-oxide semiconductor (CMOS) patch antenna consisting of several metal layers and very thin interdielectric layers. The proposed V-shaped patch with slots allows the increased radiation resistance and broadband performance. In addition, the patch resonating at different frequency from the V-shaped patch is stacked on the top to broaden the impedance-matching bandwidth. More importantly, the slots are formed in the ground plane, which is called the defected ground structure, to further increase the radiation resistance and thus improve the bandwidth and efficiency. It is verified from electromagnetic simulations that the leakage waves from the defected ground can enhance the antenna directivity and gain by coherently interfering with the topside radiation. The proposed on-chip antenna is fabricated using a standard 65 nm CMOS process. The on-wafer measurement shows very wide bandwidth in input reflection coefficient (<−10 dB), greater than 28.7% from 240 to >320 GHz. The measured peak gain was as high as 5.48 dBi at 295 GHz. To the best of the authors’ knowledge, these results belong to the best performance among the terahertz CMOS on-chip antennas without using additional components or processes such as dielectric resonators, lens, or substrate thinning.

Description: Sensors, Vol. 18, Pages 2430: Relative Pose Based Redundancy Removal: Collaborative RGB-D Data Transmission in Mobile Visual Sensor Networks Sensors doi: 10.3390/s18082430 Authors: Xiaoqin Wang Y. Ahmet Şekercioğlu Tom Drummond Vincent Frémont Enrico Natalizio Isabelle Fantoni In this paper, the Relative Pose based Redundancy Removal (RPRR) scheme is presented, which has been designed for mobile RGB-D sensor networks operating under bandwidth-constrained operational scenarios. The scheme considers a multiview scenario in which pairs of sensors observe the same scene from different viewpoints, and detect the redundant visual and depth information to prevent their transmission leading to a significant improvement in wireless channel usage efficiency and power savings. We envisage applications in which the environment is static, and rapid 3D mapping of an enclosed area of interest is required, such as disaster recovery and support operations after earthquakes or industrial accidents. Experimental results show that wireless channel utilization is improved by 250% and battery consumption is halved when the RPRR scheme is used instead of sending the sensor images independently.

Description: Sensors, Vol. 18, Pages 2439: HemoKinect: A Microsoft Kinect V2 Based Exergaming Software to Supervise Physical Exercise of Patients with Hemophilia Sensors doi: 10.3390/s18082439 Authors: Fernando Mateo Emilio Soria-Olivas Juan Carrasco Santiago Bonanad Felipe Querol Sofía Pérez-Alenda Patients with hemophilia need to strictly follow exercise routines to minimize their risk of suffering bleeding in joints, known as hemarthrosis. This paper introduces and validates a new exergaming software tool called HemoKinect that intends to keep track of exercises using Microsoft Kinect V2’s body tracking capabilities. The software has been developed in C++ and MATLAB. The Kinect SDK V2.0 libraries have been used to obtain 3D joint positions from the Kinect color and depth sensors. Performing angle calculations and center-of-mass (COM) estimations using these joint positions, HemoKinect can evaluate the following exercises: elbow flexion/extension, knee flexion/extension (squat), step climb (ankle exercise) and multi-directional balance based on COM. The software generates reports and progress graphs and is able to directly send the results to the physician via email. Exercises have been validated with 10 controls and eight patients. HemoKinect successfully registered elbow and knee exercises, while displaying real-time joint angle measurements. Additionally, steps were successfully counted in up to 78% of the cases. Regarding balance, differences were found in the scores according to the difficulty level and direction. HemoKinect supposes a significant leap forward in terms of exergaming applicability to rehabilitation of patients with hemophilia, allowing remote supervision.

Description: Sensors, Vol. 18, Pages 2428: Narrowband Characterization of Near-Ground Radio Channel for Wireless Sensors Networks at 5G-IoT Bands Sensors doi: 10.3390/s18082428 Authors: Hicham Klaina Ana Vazquez Alejos Otman Aghzout Francisco Falcone In this contribution, a narrowband radio channel model is proposed for rural scenarios in which the radio link operates under near-ground conditions for application in wireless sensor networks dedicated to smart agriculture. The received power attenuation was measured for both transmitter and receiver antennas placed at two different heights above ground: 0.2 and 0.4 m. Three frequency ranges, proposed for future 5G-IoT use case in agriculture, were chosen: 868 MHz, 2.4 GHz and 5.8 GHz. Three ground coverings were tested in a rural scenario: soil, short and tall grass fields. The path loss was then estimated as dependent of the radio link range and a three-slope log-normal path loss model was tailored. Results are explained in terms of the first Fresnel zone obstruction. Commercial Zigbee sensor nodes operating at 2.4 GHz were used in a second experiment to estimate the link quality from the experimental Radio Signal Strength Indicator (RSSI) received values. Two sensor nodes were placed at the same elevation above ground as in the previous experiment, only for short grass field case. The Quality of Service performance was determined in terms of theoretical bit error rate achieved for different digital modulations—BPSK, 8PSK and 16QAM—concluding remarkable results for an obstructed radio link.

Description: Sensors, Vol. 18, Pages 2429: A PUF- and Biometric-Based Lightweight Hardware Solution to Increase Security at Sensor Nodes Sensors doi: 10.3390/s18082429 Authors: Rosario Arjona Miguel Ángel Prada-Delgado Javier Arcenegui Iluminada Baturone Security is essential in sensor nodes which acquire and transmit sensitive data. However, the constraints of processing, memory and power consumption are very high in these nodes. Cryptographic algorithms based on symmetric key are very suitable for them. The drawback is that secure storage of secret keys is required. In this work, a low-cost solution is presented to obfuscate secret keys with Physically Unclonable Functions (PUFs), which exploit the hardware identity of the node. In addition, a lightweight fingerprint recognition solution is proposed, which can be implemented in low-cost sensor nodes. Since biometric data of individuals are sensitive, they are also obfuscated with PUFs. Both solutions allow authenticating the origin of the sensed data with a proposed dual-factor authentication protocol. One factor is the unique physical identity of the trusted sensor node that measures them. The other factor is the physical presence of the legitimate individual in charge of authorizing their transmission. Experimental results are included to prove how the proposed PUF-based solution can be implemented with the SRAMs of commercial Bluetooth Low Energy (BLE) chips which belong to the communication module of the sensor node. Implementation results show how the proposed fingerprint recognition based on the novel texture-based feature named QFingerMap16 (QFM) can be implemented fully inside a low-cost sensor node. Robustness, security and privacy issues at the proposed sensor nodes are discussed and analyzed with experimental results from PUFs and fingerprints taken from public and standard databases.

Description: Sustainability, Vol. 10, Pages 2633: Scenario-Based Simulation of Tianjin City Using a Cellular Automata–Markov Model Sustainability doi: 10.3390/su10082633 Authors: Ruci Wang Hao Hou Yuji Murayama Rapid urbanization is occurring throughout China, especially in megacities. Using a land use model to obtain future land use/cover conditions is an essential method to prevent chaotic urban sprawl and imbalanced development. This study utilized historical Landsat images to create land use/cover maps to predict the land use/cover changes of Tianjin city in 2025 and 2035. The cellular automata–Markov (CA–Markov) model was applied in the simulation under three scenarios: the environmental protection scenario (EPS), crop protection scenario (CPS), and spontaneous scenario (SS). The model achieved a kappa value of 86.6% with a figure of merit (FoM) of 12.18% when compared to the empirical land use/cover map in 2015. The results showed that the occupation of built-up areas increased from 29.13% in 2015 to 38.68% (EPS), 36.18% (CPS), and 47.94% (SS) in 2035. In this context, current urbanization would bring unprecedented stress on agricultural resources and forest ecosystems, which could be attenuated by implementing protection policies along with decelerating urban expansion. The findings provide valuable information for urban planners to achieve sustainable development goals.

Description: Sustainability, Vol. 10, Pages 2629: Pathways to Coastal Resiliency: The Adaptive Gradients Framework Sustainability doi: 10.3390/su10082629 Authors: Elisabeth M. Hamin Yaser Abunnasr Max Roman Dilthey Pamela K. Judge Melissa A. Kenney Paul Kirshen Thomas C. Sheahan Don J. DeGroot Robert L. Ryan Brain G. McAdoo Leonard Nurse Jane A. Buxton Ariana E. Sutton-Grier Elizabeth A. Albright Marielos Arlen Marin Rebecca Fricke Current and future climate-related coastal impacts such as catastrophic and repetitive flooding, hurricane intensity, and sea level rise necessitate a new approach to developing and managing coastal infrastructure. Traditional “hard” or “grey” engineering solutions are proving both expensive and inflexible in the face of a rapidly changing coastal environment. Hybrid solutions that incorporate natural, nature-based, structural, and non-structural features may better achieve a broad set of goals such as ecological enhancement, long-term adaptation, and social benefits, but broad consideration and uptake of these approaches has been slow. One barrier to the widespread implementation of hybrid solutions is the lack of a relatively quick but holistic evaluation framework that places these broader environmental and societal goals on equal footing with the more traditional goal of exposure reduction. To respond to this need, the Adaptive Gradients Framework was developed and pilot-tested as a qualitative, flexible, and collaborative process guide for organizations to understand, evaluate, and potentially select more diverse kinds of infrastructural responses. These responses would ideally include natural, nature-based, and regulatory/cultural approaches, as well as hybrid designs combining multiple approaches. It enables rapid expert review of project designs based on eight metrics called “gradients”, which include exposure reduction, cost efficiency, institutional capacity, ecological enhancement, adaptation over time, greenhouse gas reduction, participatory process, and social benefits. The framework was conceptualized and developed in three phases: relevant factors and barriers were collected from practitioners and experts by survey; these factors were ranked by importance and used to develop the initial framework; several case studies were iteratively evaluated using this technique; and the framework was finalized for implementation. The article presents the framework and a pilot test of its application, along with resources that would enable wider application of the framework by practitioners and theorists.

Description: Sustainability, Vol. 10, Pages 2627: Photovoltaic Power Forecasting Based on EEMD and a Variable-Weight Combination Forecasting Model Sustainability doi: 10.3390/su10082627 Authors: Hui Wang Jianbo Sun Weijun Wang It is widely considered that solar energy will be one of the most competitive energy sources in the future, and solar energy currently accounts for high percentages of power generation in developed countries. However, its power generation capacity is significantly affected by several factors; therefore, accurate prediction of solar power generation is necessary. This paper proposes a photovoltaic (PV) power generation forecasting method based on ensemble empirical mode decomposition (EEMD) and variable-weight combination forecasting. First, EEMD is applied to decompose PV power data into components that are then combined into three groups: low-frequency, intermediate-frequency, and high-frequency. These three groups of sequences are individually predicted by the variable-weight combination forecasting model and added to obtain the final forecasting result. In addition, the design of the weights for combination forecasting was studied during the forecasting process. The comparison in the case study indicates that in PV power generation forecasting, the prediction results obtained by the individual forecasting and summing of the sequences after the EEMD are better than those from direct prediction. In addition, when the single prediction model is converted to a variable-weight combination forecasting model, the prediction accuracy is further improved by using the optimal weights.

Description: Sustainability, Vol. 10, Pages 2622: A Rough Multi-Criteria Decision-Making Approach for Sustainable Supplier Selection under Vague Environment Sustainability doi: 10.3390/su10082622 Authors: Huiyun Lu Shaojun Jiang Wenyan Song Xinguo Ming With the growing awareness of environmental and social issues, sustainable supply chain management (SSCM) has received considerable attention both in academia and industry. Supplier selection plays an important role in the successful implementation of sustainable supply chain management, because it can influence the performance of SSCM. Sustainable supplier selection is a typical multi-criteria decision-making problem involving subjectivity and vagueness. Although some previous researches of supplier selection use fuzzy approaches to deal with vague information, it has been criticized for requiring much priori information and inflexibility in manipulating vagueness. Moreover, the previous methods often omit the environmental and social evaluation criteria in the supplier selection. To manipulate these problems, a new approach based on the rough set theory and ELECTRE (ELimination Et Choix Traduisant la REalité) is developed in this paper. The novel approach integrates the strength of rough set theory in handling vagueness without much priori information and the merit of ELECTRE in modeling multi-criteria decision-making problem. Finally, a case study of sustainable supplier selection for solar air-conditioner manufacturer is provided to demonstrate the application and potential of the approach.

Description: Sustainability, Vol. 10, Pages 2624: Economic Transition and Changing Location of Manufacturing Industry in China: A Study of the Yangtze River Delta Sustainability doi: 10.3390/su10082624 Authors: Jiawei Wu Yehua Dennis Wei Qizhai Li Feng Yuan Industrial restructuring is widely considered an important force in regional economic growth and sustainable development. With increased globalization and economic transition, a dramatic industrial restructuring has been taking place in China. Applying geographically weighted shift-share model (GW-SSM) and geographically and temporally weighted regression model (GTWR), we analyze (re)location dynamics and determinants of the manufacturing industry in the Yangtze River Delta (YRD) from 1999 to 2013, with particular attention to the implications of economic transition and institutional restructuring. We find that high-tech and capital-intensive manufacturing industries agglomerated in coastal cities, while labor-intensive and resource-based sectors have become spatially more dispersed to peripheral areas. We also find that the development of service and high-tech industries, rising labor costs, and more strict environmental regulations have facilitated the geographic dispersion of labor- and pollution-intensive industries. Moreover, regions with advantages in intermediate goods, preferential policies, and urbanization economies are attractive to capital- and technology-intensive manufacturing industries. Our research suggests that development policies should be tailored to specific regions to promote local production and innovative networks and make manufacturing industries more competitive.

Description: Sustainability, Vol. 10, Pages 2621: Adoption of Conservation Tillage on the Semi-Arid Loess Plateau of Northwest China Sustainability doi: 10.3390/su10082621 Authors: Qingfeng Han Kadambot H. M. Siddique Fengmin Li Conservation tillage is an important approach to prevent water loss and soil erosion and promote soil fertility that has been adopted widely throughout the world. However, despite promotion of the benefits of conservation tillage, obstacles are still encountered in some regions. A survey of 385 farmer households in the semi-arid Loess Plateau of China was conducted to assess the adoption of conservation tillage (ACT). This investigation was located in two counties that have run conservation tillage demonstrations with wheat for at least eight years. A binary logistic regression model was used to quantify the factors determining whether or not farmers adopt conservation tillage. Farmer’s education level, the influence of training, and field demonstrations by agricultural departments had significant positive effects on ACT. Although the adoption rate of conservation tillage in this paper was very high (89%), farmers were reluctant to continue practicing conservation tillage based on their experiences, which is contrary to the expectations of the government. The area available for planting winter wheat and the number of arable plots per household also had significant positive effects on ACT. However, the total cultivated area of land per household had a significant negative impact on ACT. Farmer awareness of conservation tillage technology, the distance from a farmer’s house to the nearest agricultural market, and the size of the active labor force in the family had significant negative impacts on ACT. These results will help in the development of more effective and targeted policies to improve the sustainability of farming systems on the semi-arid Loess Plateau.

Description: Sustainability, Vol. 10, Pages 2620: Transition towards Energy Efficiency: Developing the Nigerian Building Energy Efficiency Code Sustainability doi: 10.3390/su10082620 Authors: Susanne Geissler Doris Österreicher Ene Macharm In Nigeria, there is an estimated deficit of 17 million housing units. Power supply is insufficient, and the electricity supply for about 60 million Nigerians relies on private generators, causing noise, pollution, and high expenditures for mainly imported fuel. Altogether, current challenges clearly demonstrate the need for effective energy efficiency policies targeting also the building sector. The Nigerian Energy Support Program began in 2013, among others, with the objective being to support the Nigerian Government in developing the Nigerian Building Energy Efficiency Code. This paper presents two preparatory activities carried out in order to come up with suggestions for a legal framework well suited for the situation on the ground: the Case Study Building Analysis carried out in collaboration with a Nigerian developer and the Nigerian Building Energy Efficiency Guideline, elaborated together with stakeholders. The results of preparatory activities pointed out that the code must put emphasis on climate adaptive design and must define requirements and procedures in a clear and simple way to allow for effective enforcement. Only then can energy-efficient mass housing be feasible in Nigeria. The paper concludes with a description of the Nigerian Building Energy Efficiency Code (BEEC), officially approved and launched by the Federal Minister of Power, Works and Housing on 29 August 2017.

Description: Sustainability, Vol. 10, Pages 2619: Are the World-Leading Primary Silver Mines Exhausting? Sustainability doi: 10.3390/su10082619 Authors: Marcello Ruberti Stefania Massari Silver is one of the rarest metals in nature and certainly among the most used ones, not only as precious good for financial investments but also for many industrial critical applications. Because it would be very difficult to analyze the situation regarding the future global availability of silver as a commodity in general, due to the necessity of a large amount of data which are hardly available, we have focused only on the mining production of primary silver. In particular, the study regards the activities of a sample consisting of twelve of the world top fifteen leading primary silver mines, which represent the 54% of the worldwide primary silver production and 16% of the global silver mining production. We have investigated the related exploitation state and trends of these twelve sites by elaborating their last ten-years statistics on silver production, ore grades, resources and reserves. The findings of this study, in short, are that the cumulative average silver ore grades, both in extracted mineral, resources and reserves, of the above selected mines, have decreased and also that the new mining fields (Dukat, San Bartolomé, Pirquitas, Saucito) have lower silver content indexes than the older ones.

Description: Sustainability, Vol. 10, Pages 2617: Exploring Twitter for CSR Disclosure: Influence of CEO and Firm Characteristics in Latin American Companies Sustainability doi: 10.3390/su10082617 Authors: Yuli Marcela Suárez-Rico Mauricio Gómez-Villegas María Antonia García-Benau Social networks, which are characterised by accessibility and interactivity, offer great potential for dialogue between companies and stakeholders, for example as platforms for publishing information on aspects of corporate social responsibility (CSR). In this paper, we use a synthetic index to analyse levels of CSR disclosure via Twitter, and identify explanatory variables of this disclosure by studying the demographic characteristics of the Chief Executive Officer (CEO) and of the company. This synthetic index was based on data for 93 companies located in the four countries of the Pacific Alliance (Chile, Colombia, Mexico, and Peru), using categories based on the 2016 Global Reporting Initave (GRI) Standards. The tweets were compiled during a period of two months in 2017, immediately before and after the publication of each CSR report. The synthetic index was taken as the dependent variable and used as the basis for multivariate regression analysis to identify the relationship between the level of CSR disclosure on Twitter and the characteristics of the firm and its CEO. The results obtained show that firms operating in environmentally-sensitive industries present higher levels of CSR disclosure on Twitter than those in other sectors. By country of origin, the Colombian and Chilean companies offered higher levels of disclosure than those in Mexico and Peru. The regression analysis revealed a positive relationship between the firm operating in a sensitive industry and its level of CSR disclosure on Twitter, and an inverse relationship between the latter variable and the tenure of the CEO.

Description: Energies, Vol. 11, Pages 1961: A Novel High Efficiency Quasi-Resonant Converter Energies doi: 10.3390/en11081961 Authors: Tianyu Zhu Jianze Wang Yanchao Ji Yiqi Liu In this paper, a new constant-frequency quasi-resonant converter is proposed. Compared with the traditional LLC converter, the proposed converter can effectively reduce the range of the operating frequency. The output voltage is changed to adjust the reactance of the resonant cavity. The proposed converter has a better loss factor. To verify the theoretical analysis and soft-switching condition, a 250 W, 100 V output prototype was built and compared with the full-bridge LLC converter. Analysis and experimental results verify that a smaller operating frequency range and volume of the transformers, a soft-switching condition, and a higher overall efficiency are achieved with the proposed converter.

Description: Energies, Vol. 11, Pages 1957: Dual-Temperature Evaluation of a High-Temperature Insulation System for Liquid-Immersed Transformer Energies doi: 10.3390/en11081957 Authors: Xiaojing Zhang Lu Ren Haichuan Yu Yang Xu Qingquan Lei Xin Li Baojia Han A high-temperature oil–paper insulation system offers an opportunity to improve the overloading capability of distribution transformers facing seasonal load variation. A high-temperature electrical insulation system (EIS) was chosen due to thermal calculation based on a typical loading curve on the China Southern Power Grid. In order to evaluate candidate high-temperature insulation systems, Nomex® T910 (aramid-enhanced cellulose) immersed in FR3 (natural ester) was investigated by a dual-temperature thermal aging test compared with a conventional insulation system, Kraft paper impregnated with mineral oil. Throughout the thermal aging test, mechanical, chemical, and dielectric parameters of both paper and insulating oil were investigated in each aging cycle. The thermal aging results determined that the thermal class of the FR3-T910 insulation system meets the request of overloading transformer needs.

Description: Energies, Vol. 11, Pages 1954: Experimental Study of Flow-Induced Whistling in Pipe Systems Including a Corrugated Section Energies doi: 10.3390/en11081954 Authors: Hee-Chang LIM Faran RAZI When air flows through pipe systems that include a corrugated segment, a whistling tone is generated and increases in intensity with increasing flow velocity. This whistling sound is related to the particular geometry of corrugated pipes, which is in the form of alternating cavities. This whistling is an environmental noise problem as well as a possible structural danger because of the resulting induced vibration. This paper studies the whistling behavior of various pipe systems with a combination of smooth and corrugated pipes through a series of experiments. The considered pipe systems consist of two smooth pipes attached at the upstream and downstream ends of a corrugated segment. Experiments with smooth and corrugated pipes, which had inner diameters of 15.25 and 16.5 mm, respectively, and various lengths, were performed for flow velocities of up to approximately 30 m/s. The minimum and maximum Strouhal numbers (St) obtained during our experiments were 0.25 and 0.38, respectively. For all pipe configurations investigated in this study, the lowest Mach number at which whistling was observed was 0.017, and the maximum was 0.093. The lowest frequency at which whistling was detected in our experiments was 650 Hz, and the highest was 3080 Hz. The results presented in the form of different variables and dimensionless parameters, including the frequency, Mach number, Strouhal number, and Helmholtz number. The average mode gap and number of excited acoustic modes were also taken into account for all considered configurations. The pipe systems with longer corrugated segments had broader whistling ranges than did configurations with shorter segments, indicating that the number of cavities inside the corrugated pipe has a direct effect on whistling. Increasing the smooth pipe length (either upstream or downstream) resulted in a decrease in the average mode gap between successive modes. The number of excited acoustic modes was primarily related to the corrugated segment length, but the smooth pipe length also had a pronounced effect on the excited modes for a constant corrugation length. The highest number of excited modes (13) was seen in the case of corrugated length 450 mm and smooth pipe length (either upstream or downstream) 400 mm while the lowest number of excited modes (1) was observed for corrugated length 250 mm and smooth pipe length (downstream) 300 mm and 400 mm.

Description: Energies, Vol. 11, Pages 1950: Investigation of Injection Strategy of Branched-Preformed Particle Gel/Polymer/Surfactant for Enhanced Oil Recovery after Polymer Flooding in Heterogeneous Reservoirs Energies doi: 10.3390/en11081950 Authors: Hong He Jingyu Fu Baofeng Hou Fuqing Yuan Lanlei Guo Zongyang Li Qing You The heterogeneous phase combination flooding (HPCF) system which is composed of a branched-preformed particle gel (B-PPG), polymer, and surfactant has been proposed to enhance oil recovery after polymer flooding in heterogeneous reservoirs by mobility control and reducing oil–water interfacial tension. However, the high cost of chemicals can make this process economically challenging in an era of low oil prices. Thus, in an era of low oil prices, it is becoming even more essential to optimize the heterogeneous phase combination flooding design. In order to optimize the HPCF process, the injection strategy has been designed such that the incremental oil recovery can be maximized using the corresponding combination of the B-PPG, polymer, and surfactant, thereby ensuring a more economically-viable recovery process. Different HPCF injection strategies including simultaneous injection and alternation injection were investigated by conducting parallel sand pack flooding experiments and large-scale plate sand pack flooding experiments. Results show that based on the flow rate ratio, the pressure rising area and the incremental oil recovery, no matter whether the injection strategy is simultaneous injection or alternation injection of HPCF, the HPCF can significantly block high permeability zone, increase the sweep efficiency and oil displacement efficiency, and effectively improve oil recovery. Compared with the simultaneous injection mode, the alternation injection of HPCF can show better sweep efficiency and oil displacement efficiency. Moreover, when the slug of HPCF and polymer/surfactant with the equivalent economical cost is injected by alternation injection mode, as the alternating cycle increases, the incremental oil recovery increases. The remaining oil distribution at different flooding stages investigated by conducting large-scale plate sand pack flooding experiments shows that alternation injection of HPCF can recover more remaining oil in the low permeability zone than simultaneous injection. Hence, these findings could provide the guidance for developing the injection strategy of HPCF to further enhance oil recovery after polymer flooding in heterogeneous reservoirs in the era of low oil prices.

Description: Sensors, Vol. 18, Pages 2448: Application-Aware Anomaly Detection of Sensor Measurements in Cyber-Physical Systems Sensors doi: 10.3390/s18082448 Authors: Amin Ghafouri Aron Laszka Koutsoukos Detection errors such as false alarms and undetected faults are inevitable in any practical anomaly detection system. These errors can create potentially significant problems in the underlying application. In particular, false alarms can result in performing unnecessary recovery actions while missed detections can result in failing to perform recovery which can lead to severe consequences. In this paper, we present an approach for application-aware anomaly detection (AAAD). Our approach takes an existing anomaly detector and configures it to minimize the impact of detection errors. The configuration of the detectors is chosen so that application performance in the presence of detection errors is as close as possible to the performance that could have been obtained if there were no detection errors. We evaluate our result using a case study of real-time control of traffic signals, and show that the approach outperforms significantly several baseline detectors.

Description: Sensors, Vol. 18, Pages 2444: Utilization of Inexpensive Carbon-Based Substrates as Platforms for Sensing Sensors doi: 10.3390/s18082444 Authors: Minh Tran Ahmad Fallatah Alison Whale Sonal Padalkar Gold (Au) has been widely used as a material for Surface Enhanced Raman Spectroscopy (SERS) due to its plasmonic properties, stability and biocompatibility. Conventionally for SERS application, Au is deposited on a rigid substrate such as glass or silicon. The rigid substrates severely limit analyte collection efficiency as well as portability. Here, flexible substrates like carbon cloth and carbon paper were investigated as potential substrate candidates for SERS application. The flexible substrates were coated with Au nanostructures by electrodeposition. Model analyte, Rhodamine 6G was utilized to demonstrate the capabilities of the flexible SERS substrates. Additionally, the pesticide paraoxon was also detected on the flexible SERS substrates as well as on a real sample like the apple fruit.

Description: Sensors, Vol. 18, Pages 2441: A Label-Free Fluorescent Assay for the Rapid and Sensitive Detection of Adenosine Deaminase Activity and Inhibition Sensors doi: 10.3390/s18082441 Authors: Xinxing Tang Kefeng Wu Han Zhao Mingjian Chen Changbei Ma Adenosine deaminase (ADA), able to catalyze the irreversible deamination of adenosine into inosine, can be found in almost all tissues and plays an important role in several diseases. In this work, we developed a label-free fluorescence method for the detection of adenosine deaminase activity and inhibition. In the presence of ADA, ATP has been shown to be hydrolyzed. The ATP aptamer was shown to form a G-quadruplex/thioflavin T (ThT) complex with ThT and exhibited an obvious fluorescence signal. However, the ATP aptamer could bind with ATP and exhibited a low fluorescence signal because of the absence of ADA. This assay showed high sensitivity to ADA with a detection limit of 1 U/L based on an SNR of 3 and got a good linear relationship within the range of 1–100 U/L with R2 = 0.9909. The LOD is lower than ADA cutoff value (4 U/L) in the clinical requirement and more sensitive than most of the reported methods. This technique exhibited high selectivity for ADA against hoGG I, UDG, RNase H and λexo. Moreover, this strategy was successfully applied for assaying the inhibition of ADA using erythro-9-(2-hydroxy-3-nonyl) adenine (EHNA) and, as such, demonstrated great potential for the future use in the diagnosis of ADA-relevant diseases, particularly in advanced drug development.

Description: Sensors, Vol. 18, Pages 2440: A Privacy Preserving Scheme for Nearest Neighbor Query Sensors doi: 10.3390/s18082440 Authors: Yuhang Wang Zhihong Tian Hongli Zhang Shen Su Wei Shi In recent years, location privacy concerns that arise when using the nearest neighbor query services have gained increasing attention, as such services have become pervasive in mobile social networks devices and the IoT environments. State-of-the-art privacy preservation schemes focus on the obfuscation of the location information, which has suffered from various privacy attacks and the tradeoff of the quality of service. By noticing the fact that the user’s location could be replaced by their surrounding wireless sensor infrastructures in proximity, in this paper, we propose a wireless sensor access point-based scheme for the nearest neighbor query, without using the location of the user. Then, a noise-addition-based method that preserves user’s location privacy was proposed. To further strengthen the adaptability of the approach to real-world environments, several performance-enhancing methods are introduced, including an R-tree-based Noise-Data Retrieval Algorithm (RNR), and a nearest neighbor query method based on our research. Both performance and security evaluations are conducted to validate our approach. The results show the effectiveness and the practicality of our work.

Description: Energies, Vol. 11, Pages 1966: Possible Interactions and Interferences of Copper, Chromium, and Arsenic during the Gasification of Contaminated Waste Wood Energies doi: 10.3390/en11081966 Authors: Shurooq Badri Al-Badri Ying Jiang Stuart Thomas Wagland A considerable proportion (about 64%) of biomass energy is produced from woody biomass (wood and its wastes). However, waste wood (WW) is very often contaminated with metal(loid) elements at concentrations leading to toxicity emissions and damages to facilities during thermal conversion. Therefore, procedures for preventing and/or alleviating the negative impacts of these elements require further development, particularly by providing informative and supportive information regarding the phase transformations of the metal(loid)s during thermal conversion processes. Although it is well known that phase transformation depends on different factors such as elements’ vaporization characteristics, operational conditions, and process configuration; however, the influences of reaction atmosphere composition in terms of interactions and interferences are rarely addressed. In response, since Cu, Cr, and As (CCA-elements) are the most regulated elements in woody biomass, this paper aims to explore the possible interactions and interferences among CCA-elements themselves and with Ca, Na, S, Cl, Fe, and Ni from reaction atmosphere composition perspectives during the gasification of contaminated WW. To do so, thermodynamic equilibrium calculations were performed for Boudouard reaction (BR) and partial combustion reaction (PCR) with temperature ranges of 0–1300 °C and 0–1800 °C, respectively, and both reactions were simulated under pressure conditions of 1, 20, and 40 atm. Refinement of the occurred interactions and interferences reveals that Ni-As interactions generate dominant species As2Ni5 and As8Ni11, which increase the solid–gaseous transformation temperature of As. Moreover, the interactions between Ca and Cr predominantly form C3Cr7; whereas the absence of Ca leads to Cr2Na2O4 causing instability in the Cr phase transformation.

Description: Energies, Vol. 11, Pages 1967: Dry Fuel Jet Half-Angle Measurements and Correlation for an Entrained Flow Gasifier Energies doi: 10.3390/en11081967 Authors: Francis Kus Robin Hughes Arturo Macchi Poupak Mehrani Marc Duchesne Reduced order models (ROMs) are increasingly applied to entrained flow gasification development due to reduced computational requirements relative to computational fluid dynamics (CFD) models. However, they require greater a posteriori knowledge of the reactor physics. A significant parameter influencing ROM outputs is the jet half-angle of the solid fuel and oxidant mixture in the gasifier. Thus, it is important to understand the geometry of the jet in the gasifier, and how it is dependent on operating parameters, such as solid and carrier gas flow rates. In this work, an existing model for jet half-angles, which considers the ratio of surrounding gas density to jet core density, is extended to a dry solids jet with impinging gas. The model is fitted to experimental jet half-angles. The jet half-angle of a non-reactive flow was measured using laser-sheet imaging for solid fluxes in the range of 460–880 kg/m2·s and carrier gas fluxes in the range of 43–90 kg/m2·s at the transport line outlet. Jet half-angles ranged from 5.6° to 11.3°, increasing with lower solid/gas loading ratios. CFD simulations of two reactive conditions, with solid and gas fluxes similar to experiments, were used to test the applicability of the proposed jet half-angle model.

Description: Energies, Vol. 11, Pages 1968: A Review on Recent Advances and Future Trends of Transformerless Inverter Structures for Single-Phase Grid-Connected Photovoltaic Systems Energies doi: 10.3390/en11081968 Authors: Kamran Zeb Imran Khan Waqar Uddin Muhammad Adil Khan P. Sathishkumar Tiago Davi Curi Busarello Iftikhar Ahmad H. J. Kim The research significance of various scientific aspects of photovoltaic (PV) systems has increased over the past decade. Grid-tied inverters the vital elements for the effective interface of Renewable Energy Resources (RER) and utility in the distributed generation system. Currently, Single-Phase Transformerless Grid-Connected Photovoltaic (SPTG-CPV) inverters (1–10 kW) are undergoing further developments, with new designs, and interest of the solar market. In comparison to the transformer (TR) Galvanic Isolation (GI)-based inverters, its advantageous features are lower cost, lighter weight, smaller volume, higher efficiency, and less complexity. In this paper, a review of SPTG-CPV inverters has been carried out. The basic operational principles of all SPTG-CPV inverters are presented in details for positive, negative, and zero cycles. A comprehensive analysis of each topology has been deliberated. A comparative assessment is also performed based on weaknesses, strengths, component ratings, efficiency, total harmonic distortion (THD), semiconductor device losses, and leakage current of various SPTG-CPV inverters schemes. Typical PV inverter structures and control schemes for grid connected three-phase system and single-phase systems are also discussed, described, and reviewed. Comparison of various industrial grids-connected PV inverters is also performed. Loss analysis is also performed for various topologies at 1 kW. Selection of appropriate topologies for their particular application is thoroughly presented. Then, discussion and forthcoming progress are emphasized. Lastly, the conclusions are presented. More than 100 research publications on the topic of SPTG-CPV inverter topologies, configurations, and control schematics along with the recent developments are thoroughly reviewed and classified for quick reference.

Description: Energies, Vol. 11, Pages 1964: Lightning Impulse Withstand of Natural Ester Liquid Energies doi: 10.3390/en11081964 Authors: Stephanie Haegele Farzaneh Vahidi Stefan Tenbohlen Kevin J. Rapp Alan Sbravati Due to the low biodegradability of mineral oil, intense research is conducted to define alternative liquids with comparable dielectric properties. Natural ester liquids are an alternative in focus; they are used increasingly as insulating liquid in distribution and power transformers. The main advantages of natural ester liquids compared to mineral oil are their good biodegradability and mainly high flash and fire points providing better fire safety. The dielectric strength of natural ester liquids is comparable to conventional mineral oil for homogeneous field arrangements. However, many studies showed a reduced dielectric strength for highly inhomogeneous field arrangements. This study investigates at which degree of inhomogeneity differences in breakdown voltage between the two insulating liquids occur. Investigations use lightning impulses with different electrode arrangements representing different field inhomogeneity factors and different gap distances. To ensure comparisons with existing transformer geometries, investigations are application-oriented using a transformer conductor model, which is compared to other studies. Results show significant differences in breakdown voltage from an inhomogeneity factor of 0.1 (highly inhomogeneous field) depending on the gap distance. Larger electrode gaps provide a larger inhomogeneity at which differences in breakdown voltages occur.

Description: Energies, Vol. 11, Pages 1963: Numerical Analysis to Determine Reliable One-Diode Model Parameters for Perovskite Solar Cells Energies doi: 10.3390/en11081963 Authors: Esteban Velilla Juan Bernardo Cano Keony Jimenez Jaime Valencia Daniel Ramirez Franklin Jaramillo With the aim to determine the photo-generated current, diode saturation current, ideality factor, shunt, and series resistances related to the one-diode model for p-i-n planar perovskite solar cells, reference cells with active area of approximately 1 cm2 and efficiencies ranging between 4.6 and 12.2% were fabricated and characterized at standard test conditions. To estimated feasible parameters, the mean square error between the I-V curve data of these cells and the circuital model results were minimized using a Genetic Algorithm combined with the Nelder-Mead method. When considering the optimization process solutions, a numerical sensitivity analysis of the error as a function of the estimated parameters was carried out. Based on the errors behavior that is showed graphically through maps, it was demonstrated that the set of parameters estimated for each cell were reliable, meaningful, and realistic, and being related to errors lower than 9.1 × 10−9. Therefore, these results can be considered as global solutions of the optimization process. Moreover, based on the lower errors obtained from the optimization process, it was possible to affirm that the one-diode model is suitable to model the I-V curve of perovskite solar cells. Finally, the estimated parameters suggested that the average ideality factor is close to 2 when the fill factor of the I-V curves is higher than 0.5. Lower fill factors corresponded to ideality that was higher than 3, linked to lower efficiencies, and high loses effects reflected on lower shunt resistances. Lower ideality factor of 1.4 corresponds to the best performing solar cells.

Description: Energies, Vol. 11, Pages 1962: Energy Loss Allocation in Smart Distribution Systems with Electric Vehicle Integration Energies doi: 10.3390/en11081962 Authors: Paulo M. De Oliveira-De Jesus Mario A. Rios Gustavo A. Ramos This paper presents a three-phase loss allocation procedure for distribution networks. The key contribution of the paper is the computation of specific marginal loss coefficients (MLCs) per bus and per phase expressly considering non-linear load models for Electric Vehicles (EV). The method was applied in a unbalanced 12.47 kV feeder with 12,780 households and 1000 EVs under peak and off-peak load conditions. Results obtained were also compared with the traditional roll-in embedded allocation procedure (pro rata) using non-linear and standard constant power models. Results show the influence of the non-linear load model in the energy losses allocated. This result highlights the importance of considering an appropriate EV load model to appraise the overall losses encouraging the use and further development of the methodology

Description: Sensors, Vol. 18, Pages 2450: Features of X-Band Radar Backscattering Simulation Based on the Ocean Environmental Parameters in China Offshore Seas Sensors doi: 10.3390/s18082450 Authors: Tao Wu Zhensen Wu Jiaji Wu Gwanggil Jeon Liwen Ma The X-band marine radar has been employed as a remote sensing tool for sea state monitoring. However, there are few literatures about sea spectra considering both the wave parameters and short wind-wave spectra in China Offshore Seas, which are of theoretical and practical significance. Based on the wave parameters acquired from the European Centre for Medium-Range Weather Forecasts reanalysis data (ERA-Interim reanalysis data) during 36 months from 2015 to 2017, a finite depth sea spectrum considering both wind speeds and ocean environmental parameters is established in this study. The wave spectrum is then built into a modified two-scale model, which can be related to the ocean environmental parameters (wind speeds and wave parameters). The final results are the mean backscattering coefficients over the variety of sea states at a given wind speed. As the model predicts, the monthly maximum backscattering coefficients in different seas change slowly (within 4 dB). In addition, the differences of the backscattering coefficients in different seas are quite small during azimuthal angles of 0° to 90° and 270° to 360° with a relative error within 1.5 dB at low wind speed (5 m/s) and 2 dB at high wind speed (10 m/s). With the method in the paper, a corrected result from the experiment can be achieved based on the relative error analysis in different conditions.

Description: Sustainability, Vol. 10, Pages 2659: Research on the Influence of Real Estate Development on Private Investment: A Case Study of China Sustainability doi: 10.3390/su10082659 Authors: Jiangtao Li Jianyue Ji Huiwen Guo Lei Chen Private investment in China, as a developing country, is an important source of financing for Chinese SMEs (Small and Medium-Size Enterprises) and has played a major role in the development of the real economy. However, in 2016, the growth rate of private investment in China dropped from 10.18% to 3.17%, which had a significant impact on the real economy. At the same time, China’s real estate market has developed rapidly, attracting a large number of capital inflows. The relationship between real estate development and private investment in China is worth considering. This study first, theoretically analyzes the influence mechanism of real estate industry on private investment, pointing out that within a modest development range, the development of real estate industry can promote private investment through the industrial linkage, urbanization, and balance sheet effects, but when real estate is overdeveloped, it has an inhibitory effect on private investment through vampire effect, raising costs and reducing demand effect. In other words, real estate has different effects on private investment in different developmental periods. Therefore, there is a non-linear relationship between the two variables. Second, the relevant provincial panel data of 31 provinces in mainland China from 2003 to 2015 were selected. Using the dynamic panel system Generalized Method of Moments (GMM), this study estimated the correlation between real estate development and private investment. The empirical results showed that the development of the real estate industry has a significant impact on the level of private investment; the two showing an “inverted U-shaped” relationship. At present, in some provinces in China, the real estate industry has exceeded the inverted U-shaped threshold. To boost the vitality of private investment in promoting real economic growth, the development of the real estate industry should be restricted, and house prices should be properly regulated.

Description: Sustainability, Vol. 10, Pages 2657: Numerical Thermal Characterization and Performance Metrics of Building Envelopes Containing Phase Change Materials for Energy-Efficient Buildings Sustainability doi: 10.3390/su10082657 Authors: Mingli Li Guoqing Gui Zhibin Lin Long Jiang Hong Pan Xingyu Wang Residential and commercial buildings consume nearly 40 percent of total USA energy use and account for one-third of total greenhouse gas emissions. The challenges are how to effectively promote energy efficiency in buildings to respond to the high financial burden of energy consumption, while reducing pollution. Phase change materials (PCMs) have been used as passive energy storage for building systems. Along this vein, this study aims to numerically elucidate the design parameters of building envelopes strengthened by PCM layers, and unveil their impacts on building energy efficiency. Critical design variables, such as the thickness of the PCM layer, the latent heat of PCMs, or melting temperature of PCMs were selected for a parametric study, while performance metrics were used to assess building efficiency. Results revealed that PCM-enabled building walls exhibited different levels of improvement, in terms of reduction of peak temperature and temperature swings. Among the variables, the selection of the proper melting point for a PCM was identified as the most crucial parameter for determining building energy efficiency, while the heat of fusion was also observed as a critical property of PCM for building potential. Findings also demonstrated that the placement of the PCM near the interior wall surface could achieve higher efficiency, as compared to other cases. Results also showed that the thermal conductivity of PCM has a minimum contribution to energy storage capacity.

Description: Sensors, Vol. 18, Pages 2451: Interaction of Lamb Wave Modes with Weak Material Nonlinearity: Generation of Symmetric Zero-Frequency Mode Sensors doi: 10.3390/s18082451 Authors: Xiaoqiang Sun Xiangyan Ding Feilong Li Shijie Zhou Yaolu Liu Ning Hu Zhongqing Su Youxuan Zhao Jun Zhang Mingxi Deng The symmetric zero-frequency mode induced by weak material nonlinearity during Lamb wave propagation is explored for the first time. We theoretically confirm that, unlike the second harmonic, phase-velocity matching is not required to generate the zero-frequency mode and its signal is stronger than those of the nonlinear harmonics conventionally used, for example, the second harmonic. Experimental and numerical verifications of this theoretical analysis are conducted for the primary S0 mode wave propagating in an aluminum plate. The existence of a symmetric zero-frequency mode is of great significance, probably triggering a revolutionary progress in the field of non-destructive evaluation and structural health monitoring of the early-stage material nonlinearity based on the ultrasonic Lamb waves.

Description: Sustainability, Vol. 10, Pages 2655: Substructure Hybrid Simulation Boundary Technique Based on Beam/Column Inflection Points Sustainability doi: 10.3390/su10082655 Authors: Zaixian Chen Xueyuan Yan Hao Wang Xingji Zhu Billie F. Spencer Compatibility among substructures is an issue for hybrid simulation. Traditionally, the structure model is regarded as the idealized shear model. The equilibrium and compatibility of the axial and rotational direction at the substructure boundary are neglected. To improve the traditional boundary technique, this paper presents a novel substructure hybrid simulation boundary technique based on beam/column inflection points, which can effectively avoid the complex operation for realizing the bending moment at the boundary by using the features of the inflection point where the bending moment need not be simulated in the physical substructure. An axial displacement prediction technique and the equivalent force control method are used to realize the proposed method. The numerical simulation test scheme for the different boundary techniques was designed to consider three factors: (i) the different structural layers; (ii) the line stiffness ratio of the beam to column; and (iii) the peak acceleration. The simulation results for a variety of numerical tests show that the proposed technique shows better performance than the traditional technique, demonstrating its potential in improving HS test accuracy. Finally, the accuracy and feasibility of the proposed boundary technique is verified experimentally through the substructure hybrid simulation tests of a six-story steel frame model.

Description: Sustainability, Vol. 10, Pages 2666: Understanding the Spontaneous Spreading of Stone Bunds in Ethiopia: Implications for Sustainable Land Management Sustainability doi: 10.3390/su10082666 Authors: Meskerem Abi Aad Kessler Peter Oosterveer Degefa Tolossa This study deals with the spontaneous spreading of stone bunds in the central Ethiopian highlands, i.e., the adoption and implementation of stone bunds by farmers on their own initiative. The study tests the hypothesis that spontaneously implemented stone bunds, as compared to stone bunds implemented by mass mobilization campaigns, are more integrated with other land management practices and lead to higher yields. Data are collected in the Girar Jarso woreda through field observations and household surveys. Descriptive statistics are used to analyze and test the data at 1% and 5% probability levels. Results show that stone bunds are spontaneously implemented mainly on farmlands located nearby the homesteads where farmers perceive severe erosion, poor soil fertility and steep slope gradients. Compared to stone bunds implemented by mass mobilization, spontaneously implemented stone bunds are perceived as better maintained, more frequently modified to fit the farming system and better integrated with soil fertility management practices, such as applying fertilizer, compost and manure. Particularly, this better integration with other practices is very important, because it makes stone bunds more effective in reducing erosion, leading to beneficial effects on soil moisture and soil productivity, as perceived by farmers. The study, therefore, suggests that the mass mobilization campaign should use a more participatory and integrated approach, in which there is ample space for awareness raising and learning concerning the benefits of integrated farm management, and in which farmers themselves have a leading role in the decision on where to construct stone bunds. Such a strategy will lead to more sustainable impact on soil fertility and food security than the current top-down intervention approach.

Description: Energies, Vol. 11, Pages 1970: Increase in Robustness against Effects of Coil Misalignment on Electrical Parameters Using Magnetic Material Layer in Planar Coils of Wireless Power Transfer Transformer Energies doi: 10.3390/en11081970 Authors: Joao Victor Pinon Pereira Dias Masafumi Miyatake Utilization of wireless power transfer in light rail transits is seen as one solution for electrification of lines. The main advantage of this supply system is the reduction of installation; moreover, the alignment between the transmitter coil in the track and the receiver coil in the train should be perfect in order not to affect the power transfer. To reduce the effects of misalignment on the input and output electric parameters of the system, a new planar core and coil design, called hybrid intercore coil, is proposed. The proposed design uses a magnetic material layer between the windings in the inner half of the coil to create a non-uniform magnetic field distribution, which makes the system more robust against the effects of coil misalignment on the system current and voltage. Simulations with finite element method software were conducted to compare designs. The results show that the proposed design is less susceptible to the effects of misalignment and is more efficient. Prototype cores were constructed to verify the simulation results. Measurements show a smaller input overcurrent and output overvoltage when operating in resonance mode. The proposed design reduced the effects of coil misalignment on electrical parameters.

Description: Energies, Vol. 11, Pages 1971: A New Lumped Parameter Model for Natural Gas Pipelines in State Space Energies doi: 10.3390/en11081971 Authors: Kai Wen Zijie Xia Weichao Yu Jing Gong Many algorithms and numerical methods, such as implicit and explicit finite differences and the method of characteristics, have been applied for transient flow in gas pipelines. From a computational point of view, the state space model is an effective method for solving complex transient problems in pipelines. However, the impulse output of the existing models is not the actual behavior of the pipeline. In this paper, a new lumped parameter model is proposed to describe the inertial nature of pipelines with inlet/outlet pressure and flow rate as outer variables in the state space. Starting from the basic mechanistic partial differential equations of the general one-dimensional compressible gas flow dynamics under isothermal conditions, the transfer functions are first acquired as the fundamental work. With Taylor-expansion and a transformation procedure, the inertia state space models are derived with proper simplification. Finally, three examples are used to illustrate the effectiveness of the proposed model. With the model, a real-time automatic scheduling scheme of the natural gas pipeline could be possible in the future.

Description: Energies, Vol. 11, Pages 1972: Comprehensive Design and Analysis of a State-Feedback Controller for a Dynamic Voltage Restorer Energies doi: 10.3390/en11081972 Authors: Javier Roldán-Pérez Aurelio García-Cerrada Alberto Rodríguez-Cabero Juan Luis Zamora-Macho Voltage sags result in unwanted operation stops and large economical losses in industrial applications. A dynamic voltage restorer (DVR) is a power-electronics-based device conceived to protect high-power installations against these events. However, the design of a DVR control system is not straightforward and it has some peculiarities. First of all, a DVR includes a resonant (LC) connection filter with a lightly damped resonance. Secondly, the control system of a DVR should work properly regardless of the type of load, which can be linear or non-linear, to be protected. In this paper, a digital state-feedback (SF) controller for a DVR is proposed to address these issues. The design and features of the SF controller are studied in detail. Two pole-placement alternatives are discussed and the system robustness is tested under variations in the system parameters. Furthermore, implementation aspects such as discretization not commonly addressed in the literature are described. The controller is implemented in its incremental form. A decoupling system for the dq-axis dynamics that takes into account system delays and the load current is proposed and analytically studied. The proposed controller is compared with two other alternatives found in the literature: a Proportional-Integral-Differential (PID) controller and a cascade controller. The effect of the load connected downstream a DVR is also studied, revealing the potential of the SF controller to damp the resonance under light load conditions. All control system developments were tested in a 5 kVA prototype of a DVR connected to a configurable grid.

Description: Sustainability, Vol. 10, Pages 2674: Reputation Effects in Socially Driven Sharing Economy Transactions Sustainability doi: 10.3390/su10082674 Authors: Maarten ter Huurne Amber Ronteltap Chenhui Guo Rense Corten Vincent Buskens Reputation has often been proposed as the central mechanism that creates trust in the sharing economy. However, some sharing platforms that focus primarily on social rather than economically driven exchanges have managed to facilitate exchanges between users without the use of a reputation system. This could indicate that socially driven exchanges are in less need of reputation systems and that having sufficient trust is less problematic. We examine the effect of seller reputation on sales and price as proxies for trust, using a large dataset from a Dutch meal-sharing platform. This platform aims to stimulate social interactions between people via meal sharing. Multilevel regression analyses were used to test the association of reputation with trust. Our main empirical results are that reputation affects both sales and price positively, consistent with the existing reputation literature. We also found evidence of the presence of an information effect, i.e., the influence of reputation on sharing decreases when additional profile information is provided (e.g., a profile photo, a product description). Our results thus confirm the effectiveness of reputation in more socially driven exchanges also. Consequently, platform owners are advised to use reputation on their platform to increase sharing between its users.

Description: Sensors, Vol. 18, Pages 2472: Multiple Instances QoS Routing in RPL: Application to Smart Grids Sensors doi: 10.3390/s18082472 Authors: Jad Nassar Matthieu Berthomé Jérémy Dubrulle Nicolas Gouvy Nathalie Mitton Bruno Quoitin The Smart Grid (SG) aims to transform the current electric grid into a “smarter” network where the integration of renewable energy resources, energy efficiency and fault tolerance are the main benefits. This is done by interconnecting every energy source, storage point or central control point with connected devices, where heterogeneous SG applications and signalling messages will have different requirements in terms of reliability, latency and priority. Hence, data routing and prioritization are the main challenges in such networks. So far, RPL (Routing Protocol for Low-Power and Lossy networks) protocol is widely used on Smart Grids for distributing commands over the grid. RPL assures traffic differentiation at the network layer in wireless sensor networks through the logical subdivision of the network in multiple instances, each one relying on a specific Objective Function. However, RPL is not optimized for Smart Grids, as its main objective functions and their associated metric does not allow Quality of Service differentiation. To overcome this, we propose OFQS an objective function with a multi-objective metric that considers the delay and the remaining energy in the battery nodes alongside with the dynamic quality of the communication links. Our function automatically adapts to the number of instances (traffic classes) providing a Quality of Service differentiation based on the different Smart Grid applications requirements. We tested our approach on a real sensor testbed. The experimental results show that our proposal provides a lower packet delivery latency and a higher packet delivery ratio while extending the lifetime of the network compared to solutions in the literature.

Description: Sensors, Vol. 18, Pages 2465: Improving Classification Algorithms by Considering Score Series in Wireless Acoustic Sensor Networks Sensors doi: 10.3390/s18082465 Authors: Amalia Luque Javier Romero-Lemos Alejandro Carrasco Julio Barbancho The reduction in size, power consumption and price of many sensor devices has enabled the deployment of many sensor networks that can be used to monitor and control several aspects of various habitats. More specifically, the analysis of sounds has attracted a huge interest in urban and wildlife environments where the classification of the different signals has become a major issue. Various algorithms have been described for this purpose, a number of which frame the sound and classify these frames, while others take advantage of the sequential information embedded in a sound signal. In the paper, a new algorithm is proposed that, while maintaining the frame-classification advantages, adds a new phase that considers and classifies the score series derived after frame labelling. These score series are represented using cepstral coefficients and classified using standard machine-learning classifiers. The proposed algorithm has been applied to a dataset of anuran calls and its results compared to the performance obtained in previous experiments on sensor networks. The main outcome of our research is that the consideration of score series strongly outperforms other algorithms and attains outstanding performance despite the noisy background commonly encountered in this kind of application.

Description: Sustainability, Vol. 10, Pages 2676: Measuring Social Vulnerability to Flood Disasters in China Sustainability doi: 10.3390/su10082676 Authors: Ming Zhang Wenbo Xiang Meilan Chen Zisen Mao To proactively prevent losses from flood disasters and subsequent potential human conflicts, it is critical to measure the social vulnerability of a country or a region to flood. In this article, we first propose a list of potential indicators for measuring this social vulnerability. These indicators’ significances are then tested based on their correlation coefficients with a vulnerability index obtained using nonparametric Data Envelopment Analysis. In the final measurement system, there are nine indicators: the proportion of the primary industry, infrastructure development level, income gap between urban and rural residents, the proportion of population over 60 years old, the proportion of children under 14 years old, the number of people receiving minimum income assistance, and the number of disasters per year. We then conduct principal component analysis to evaluate the social vulnerability level. Our results show that the social vulnerability level is mostly impacted by the economic principal component and the demographic and social security principal component. Moreover, our results also confirm that the social vulnerability level to flood in China declined overall from 2003 to 2015.

Description: Sustainability, Vol. 10, Pages 2673: The Public Willingness to Pay for Reducing the Incidence of Hazardous Chemical Spill Accidents by Half in South Korea Sustainability doi: 10.3390/su10082673 Authors: Hye-Jeong Lee Hyo-Jin Kim Seung-Hoon Yoo Hazardous chemical spill (HCS) accidents, which occur due to careless workers, transport accidents, etc., can be harmful to humans. Recently, an average of 96 cases of HCS accidents have taken place in South Korea annually. As a result, the government is trying to reduce the incidence of HCS accidents by 50%. Government officials are seeking information about the value that the enforcement of the reduction plan will bring for the public. This knowledge will help government officials decide whether to implement the reduction plan. This article seeks to acquire information about the public willingness to pay (WTP) for the reduction plan, employing the contingent valuation (CV) technique. For this purpose, a total of 1000 households living in South Korea participated in the CV survey in 2017. The data on the WTP were gathered using a dichotomous choice question and analyzed using the spike model. Forty-five percent of the respondents were willing to accept an increase in income taxes to carry out the reduction plan. The mean household WTP estimate was obtained as KRW 3830 (USD 3.41) per annum. The national value expanded from the sample to the population is worth KRW 74.8 billion (USD 66.6 million) per year. This value implies the public value of the reduction plan and can be applied in policy analysis and decision-making concerning the reduction of the incidence of HCS accidents.

Description: Sustainability, Vol. 10, Pages 2671: The Sustainable Characteristic of Bio-Bi-Phase Flow of Peristaltic Transport of MHD Jeffrey Fluid in the Human Body Sustainability doi: 10.3390/su10082671 Authors: Ahmed Zeeshan Nouman Ijaz Tehseen Abbas Rahmat Ellahi This study deals with the peristaltic transport of non-Newtonian Jeffrey fluid with uniformly distributed identical rigid particles in a rectangular duct. The effects of a magnetohydrodynamics bio-bi-phase flow are taken into account. The governing equations for mass and momentum are simplified using the fact that wavelength is much greater than the amplitude and small Reynolds number. A closed-form solution for velocity is obtained by means of the eigenfunction expansion method whereby pressure rise is numerically calculated. The results are graphically presented to observe the effects of different physical parameters and the suitability of the method. The results for hydrodynamic, Newtonian fluid, and single-phase problems can be respectively obtained by taking the Hartmann number (M = 0), relaxation time (λ1=0), and volume fraction (C = 0) as special cases of this problem.

Description: Energies, Vol. 11, Pages 1987: Distributed Energy Resources Scheduling and Aggregation in the Context of Demand Response Programs Energies doi: 10.3390/en11081987 Authors: Pedro Faria João Spínola Zita Vale Distributed energy resources can contribute to an improved operation of power systems, improving economic and technical efficiency. However, aggregation of resources is needed to make these resources profitable. The present paper proposes a methodology for distributed resources management by a Virtual Power Player (VPP), addressing the resources scheduling, aggregation and remuneration based on the aggregation made. The aggregation is made using K-means algorithm. The innovative aspect motivating the present paper relies on the remuneration definition considering multiple scenarios of operation, by performing a multi-observation clustering. Resources aggregation and remuneration profiles are obtained for 2592 operation scenarios, considering 548 distributed generators, 20,310 consumers, and 10 suppliers.

Description: Energies, Vol. 11, Pages 1986: The Influence of Local Environmental, Economic and Social Variables on the Spatial Distribution of Photovoltaic Applications across China’s Urban Areas Energies doi: 10.3390/en11081986 Authors: Alin Lin Ming Lu Pingjun Sun The capacity of new installed photovoltaic (PV) in China in 2017 was increased to 53.06 GW, reaching a total of 402.5 GW around the world. Photovoltaic applications have a significant role in the reduction of greenhouse gas emissions and alleviating electricity shortages in the sustainable development process of cities. Research on the factors that influenced the spatial distribution of photovoltaic applications mostly focus on a certain project or a region. However, it is a complicated process for decision-making of photovoltaic installations in urban areas. This study uses zip code level data from 83 cities to investigate the influence of local environmental, economic and social variables on the spatial distribution of photovoltaic applications across China’s urban areas. By analyzing the current situation, the locations of urban photovoltaic applications are collected and presented. Statistical analysis software is used to evaluate the influence of selected variables. In this paper, correlation analysis, principle component analysis (PCA) and cluster analysis are generated to predict urban photovoltaic installations. The results of this research show that Gross Domestic Product (GDP), electricity consumption, policy incentives, the number of photovoltaic companies, population, age, education and rate of urbanization were important factors that influenced the adoption of urban photovoltaic systems. The results also indicate that Southeast China and Hangzhou Province are currently the most promising areas as they have a higher rate of solar photovoltaic installation. These conclusions have significancefor energy policy and planning strategies by predicting the future development of urban photovoltaic applications.

Description: Energies, Vol. 11, Pages 1985: Design, Construction, and Testing of a Gasifier-Specific Solid Oxide Fuel Cell System Energies doi: 10.3390/en11081985 Authors: Alvaro Fernandes Joerg Brabandt Oliver Posdziech Ali Saadabadi Mayra Recalde Liyuan Fan Eva O. Promes Ming Liu Theo Woudstra Purushothaman Vellayan Aravind This paper describes the steps involved in the design, construction, and testing of a gasifier-specific solid oxide fuel cell (SOFC) system. The design choices are based on reported thermodynamic simulation results for the entire gasifier- gas cleanup-SOFC system. The constructed SOFC system is tested and the measured parameters are compared with those given by a system simulation. Furthermore, a detailed exergy analysis is performed to determine the components responsible for poor efficiency. It is concluded that the SOFC system demonstrates reasonable agreement with the simulated results. Furthermore, based on the exergy results, the components causing major irreversible performance losses are identified.

Description: Energies, Vol. 11, Pages 1984: Experimental Study of Mixed Gas Hydrates from Gas Feed Containing CH4, CO2 and N2: Phase Equilibrium in the Presence of Excess Water and Gas Exchange Energies doi: 10.3390/en11081984 Authors: Ludovic Nicolas Legoix Livio Ruffine Christian Deusner Matthias Haeckel This article presents gas hydrate experimental measurements for mixtures containing methane (CH4), carbon dioxide (CO2) and nitrogen (N2) with the aim to better understand the impact of water (H2O) on the phase equilibrium. Some of these phase equilibrium experiments were carried out with a very high water-to-gas ratio that shifts the gas hydrate dissociation points to higher pressures. This is due to the significantly different solubilities of the different guest molecules in liquid H2O. A second experiment focused on CH4-CO2 exchange between the hydrate and the vapor phases at moderate pressures. The results show a high retention of CO2 in the gas hydrate phase with small pressure variations within the first hours. However, for our system containing 10.2 g of H2O full conversion of the CH4 hydrate grains to CO2 hydrate is estimated to require 40 days. This delay is attributed to the shrinking core effect, where initially an outer layer of CO2-rich hydrate is formed that effectively slows down the further gas exchange between the vapor phase and the inner core of the CH4-rich hydrate grain.

Description: Energies, Vol. 11, Pages 1991: Operation and Economic Assessment of Hybrid Refueling Station Considering Traffic Flow Information Energies doi: 10.3390/en11081991 Authors: Suyang Zhou Yuxuan Zhuang Wei Gu Zhi Wu It is anticipated that the penetration of “Green-Energy” vehicles, including Electric Vehicle (EV), Fuel Cell Vehicle (FCV), and Natural Gas Vehicle (NGV) will keep increasing in next decades. The demand of refueling stations will correspondingly increase for refueling these “Green-Energy” vehicles. While such kinds of “Green-Energy” vehicles can provide both social and economic benefits, effective management of refueling various kinds of these vehicles is necessary to maintain vehicle users’ comfortabilities and refueling station’s return on investment. To tackle these problems, this paper proposes a novel energy management approach for hybrid refueling stations with EV chargers, Hydrogen pumps and gas pumps. Firstly, the detailed models of EV chargers, Hydrogen pumps with electrolyte and hydrogen tank, the gas pumps with gas tank, renewable resources, and battery energy storage systems are established. The forecasting methodologies for renewable energy, electricity price and the traffic flow are also presented to support the hybrid refueling station modeling and operation. Then, a management approach is adopted to manage the refueling various kinds of vehicles with considerations of the refueling station profitability. Finally, the proposed management approach is verified under four different kinds of tariffs- Economy-7, Economy-10, Flat-rate, and Real-Time Pricing (RTP), finding that the proposed management approach has the best performance under RTP tariff. The economic assessment of the Energy Storage System (ESS) is also performed. It is found that the ESS can make the saving up to $127 per day. Different sizes of gas storage tank are compared in the final section as well. The result shows that increasing the size of the tank does not bring attractive extra benefits with the consideration of the investment on enlarging the tank size.

Description: Sustainability, Vol. 10, Pages 2591: Reducing Seismic Vulnerability and Energy Demand of Cities through Green Infrastructure Sustainability doi: 10.3390/su10082591 Authors: Riccardo Privitera Daniele La Rosa Historically, urbanization processes in Italy resulted in built environments with high levels of seismic vulnerability, low energy efficiency and a lack of green spaces. The latter represent the main providers of ecosystem services in cities and play a relevant role in reducing the effects of climate change by the regulation of microclimate and urban heat islands that are responsible for building energy consumption. Despite their importance in providing ecosystem services, the implementation of green infrastructure challenges limited financial resources for the public acquisition of private plots. This paper proposes a strategy to implement an urban green infrastructure aimed at generating a double positive effect on cities by triggering seismic retrofitting and the reduction of cooling energy demand of the existing urban fabric. This is proposed through a transfer of development rights program where landowners gain economic incentives to adopt seismic retrofitting interventions and, at the same time, public administrations implement the green infrastructure in the portion of areas transferred to the municipality. The energy efficiency of buildings closer to the green infrastructure, therefore, benefits from the cooling effects of this new greenery. The strategy is tested under different scenarios of acquisition of private land by public administrations in the metropolitan area of Catania (Italy).

Description: Sustainability, Vol. 10, Pages 2588: Identifying Economic Growth Convergence Clubs and Their Influencing Factors in China Sustainability doi: 10.3390/su10082588 Authors: Feng Li Guangdong Li Weishan Qin Jing Qin Haitao Ma Balanced and coordinated economic development across regions is a critical goal of regional economic development and new-type urbanization in China. However, few studies have examined economic growth convergence clubs at the county level. To extend the research on convergence clubs, this research applies a log t convergence test and a dynamic spatial ordered probit model (DSOP) to endogenously identify economic growth convergence clubs in counties and to examine the influence of initial states and structures on club convergence probability. The study sample covers 2286 counties of China from 1992 to 2010. The results show significant convergence club patterns at the county levels, resulting in the gradual formation of six convergence clubs. The DSOP estimation results show that per capita fixed assets, population density, and industrialization have promoted convergence club formation to varying degrees.

Description: Sustainability, Vol. 10, Pages 2594: Resilient Entrepreneurship among European Higher Education Graduates Sustainability doi: 10.3390/su10082594 Authors: Ana-Maria Zamfir Cristina Mocanu Adriana Grigorescu Resilience represents the ability of systems and individuals to adapt and overcome the difficulties and challenges they face. Resilient entrepreneurs are those who cope with stressful or adverse situations by relying on both internal and external factors. This article examines the way higher education graduates express entrepreneurial resilience in various national contexts. We analyze the Research into Employment and professional Flexibility (REFLEX) data set that provides information on early career of higher education graduates leaving education in the academic year 1999/2000 in 13 European countries. We study resilience in entrepreneurship by considering both how long higher education graduates succeed to remain in self-employment and the extent to which they re-entry in entrepreneurship after exiting. Survival analyses, logistic and cox regressions indicate important differences in patterns of starting, remaining and returning in self-employment and in factors influencing the retention in entrepreneurship among higher education graduates. It is argued that structural factors, personal characteristics and educational background explain a large amount of variation in resilient entrepreneurship.

Description: Energies, Vol. 11, Pages 1998: Design Issues for Claw Pole Machines with Soft Magnetic Composite Cores Energies doi: 10.3390/en11081998 Authors: Chengcheng Liu Jiawei Lu Youhua Wang Gang Lei Jianguo Zhu Youguang Guo By using global ring winding, the torque coefficient of the transverse flux machine (TFM) is proportional to its number of pole pairs, and thus the TFM possesses high torque density ability when compared with other electrical machines. As a special kind of TFM, the claw pole machine (CPM) can have more torque due to its special claw pole teeth. The manufacturing of CPM or TFM with silicon steels was very difficult in the past, and is a handicap for the progress of this kind of machine. Thanks to the advent of soft magnetic composite (SMC) materials, the manufacturing process of CPM has become more and more simple. More attention has been paid to this kind of technology, and some mass production CPMs with SMC cores have appeared. However, there are few works that discuss the key design issues for this kind of machine. In this paper, a small CPM with SMC is used as as a research benchmark. Various design methods that can be adopted to improve its performance have been studied, including unequal stator claw pole teeth, a skewing magnet design, consequent pole design, and etc. The 3D finite element method (FEM) is used for the machine analysis, and it is verified by the experimental results of a CPM with SMC cores.

Description: Energies, Vol. 11, Pages 1992: Assessment and Performance Evaluation of a Wind Turbine Power Output Energies doi: 10.3390/en11081992 Authors: Akintayo Temiloluwa Abolude Wen Zhou Estimation errors have constantly been a technology bother for wind power management, often time with deviations of actual power curve (APC) from the turbine power curve (TPC). Power output dispersion for an operational 800 kW turbine was analyzed using three averaging tine steps of 1-min, 5-min, and 15-min. The error between the APC and TPC in kWh was about 25% on average, irrespective of the time of the day, although higher magnitudes of error were observed during low wind speeds and poor wind conditions. The 15-min averaged time series proved more suitable for grid management and energy load scheduling, but the error margin was still a major concern. An effective power curve (EPC) based on the polynomial parametric wind turbine power curve modeling technique was calibrated using turbine and site-specific performance data. The EPC reduced estimation error to about 3% in the aforementioned time series during very good wind conditions. By integrating statistical wind speed forecasting methods and site-specific EPCs, wind power forecasting and management can be significantly improved without compromising grid stability.

Description: Sustainability, Vol. 10, Pages 2710: An Analysis of the Energy Consumption Behavior of Scaled, Containerized Web Apps Sustainability doi: 10.3390/su10082710 Authors: Sandro Kreten Achim Guldner Stefan Naumann Containerization is one of the most important topics for modern data centers and web developers. Since the number of containers on one- and multi-node systems is growing, knowledge about the energy consumption behavior of single web-service containers is essential in order to save energy and, of course, money. In this article, we are going to show how the energy consumption behavior of single containerized web services/web apps changes while creating replicas of the service in order to scale and balance the web service.

Description: Energies, Vol. 11, Pages 1995: Active-Current Control of Large-Scale Wind Turbines for Power System Transient Stability Improvement Based on Perturbation Estimation Approach Energies doi: 10.3390/en11081995 Authors: Peng Shen Lin Guan Zhenlin Huang Liang Wu Zetao Jiang This paper proposes an active-current control strategy for large-scale wind turbines (WTs) to improve the transient stability of power systems based on a perturbation estimation (PE) approach. The main idea of this control strategy is to mitigate the generator imbalance of mechanical and electrical powers by controlling the active-current of WTs. The effective mutual couplings of synchronous generators and WTs are identified using a Kron-reduction technique first. Then, the control object of each WT is assigned based on the identified mutual couplings. Finally, an individual controller is developed for each WT using a PE approach. In the control algorithm, a perturbation state (PS) is introduced for each WT to represent the comprehensive effect of the nonlinearities and parameter variations of the power system, and then it is estimated by a designed perturbation observer. The estimated PS is employed to compensate the actual perturbation, and to finally achieve the adaptive control design without requiring an accurate system model. The effectiveness of the proposed control approach on improving the system transient stability is validated in the modified IEEE 39-bus system.

Description: Sustainability, Vol. 10, Pages 2699: A Framework for Regional Ecological Risk Warning Based on Ecosystem Service Approach: A Case Study in Ganzi, China Sustainability doi: 10.3390/su10082699 Authors: Tian Dong Weihua Xu Hua Zheng Yang Xiao Lingqiao Kong Zhiyun Ouyang Worldwide, most ecosystem services have declined. However, the theoretical and analytical frameworks for the ecological risk assessment of ecosystem services are still lacking. Here a framework for the risk assessment of ecosystem services was developed based on the formation, changes, risk, and management of ecosystem services. The framework was tested in Ganzi, the upstream area of the Yangtze River Basin, for the regional ecological warning of ecosystem services. Ecosystem services in the form of soil retention and sandstorm prevention and ecological risks including soil and wind erosion were modelled. The results showed that with the increase in area and quality of natural vegetation (forest and grassland), the soil retention service and sandstorm prevention service increased by 66.92% and 8.59% between 2000 and 2015, respectively. Correspondingly, the ecological risk of soil erosion decreased by 8.8%, and wind erosion remained stable. Despite the negative impacts from agricultural development on sandstorm prevention, the increase in vegetation and improvement in ecological quality led to a decrease in the ecological risks of soil erosion and sandstorm erosion by improvement of ecosystem services. This research provides a new perspective for ecological risk assessment, as well as direct management information on ecological risks, by incorporating ecosystem services.

Description: Energies, Vol. 11, Pages 2018: Technological Solutions for Recycling Ash Slag from the Cao Ngan Coal Power Plant in Vietnam Energies doi: 10.3390/en11082018 Authors: Thriveni Thenepalli Nguyen Thi Minh Ngoc Lai Quang Tuan Trinh Hai Son Ho Huu Hieu Dang Tran Nhu Thuy Nguyen Thi Thanh Thao Duong Thi Thanh Tam Doan Thi Ngoc Huyen Tran Tan Van Ramakrishna Chilakala Ji Whan Ahn Annually, coal-fired power plants in Vietnam discharge hundreds of thousand tons of coal ash. Most of this ash goes into the environment without treatment or any plan for the efficient reuse of this precious resource. There are many reasons for this, such as poor quality of the ash, no suitable and feasible ash treatment technology, a lack of awareness about environmental pollution and resource saving, and inappropriate sanctions and policies. This study analyzed and summarized information and data pertaining to the current status of the production, discharge, and utilization of coal ash from the Cao Ngan Power Plant (CNPP) in Thai Nguyen Province, Vietnam. In addition, the potential for applying advanced emission reduction technologies in order to recycle coal ash for cement production, as well as geographical, socio-economic, and market factors were assessed. This paper reveals the results of a preliminary assessment of carbon-mineralization technologies which seek to achieve the following three goals: (1) effectively disposing of coal ash to protect the environment and local community, (2) contributing to the nationally determined effort to mitigate greenhouse gas emissions which cause climate change, and (3) making value-added products and bringing economic benefits to a sustainable society.

Description: Energies, Vol. 11, Pages 2017: An Experimental Investigation of Thermal Characteristics of Phase Change Material Applied to Improve the Isothermal Operation of a Refrigerator Energies doi: 10.3390/en11082017 Authors: Seok-Joon Lee Seul-Hyun Park We investigated the thermal performance of a refrigerator with a functional duct unit (FDU) which was charged with a phase change material (PCM) and designed to replace the existing expandable polystyrene (EPS) duct unit. Since the performance of the FDU is dependent upon the thermal characteristics of the PCM, the eutectic water–salt solution as the PCM was prepared and tested to optimize the thermal characteristics. The thermal properties of the PCM were examined by the T-history method. When the PCM contained 1 wt.% eutectic molten salt compounds, the phase change temperature was approximately −0.5 °C, the supercooling temperature was approximately −2.9 °C, and the latent heat was 304.9 kJ/kg. Compared with other PCMs of different eutectic molten salt concentrations, this PCM was found to have the most appropriate thermal properties for the FDU. Therefore, the PCM with 1 wt.% eutectic molten salt compounds was used in the FDU, which was installed in a 200 L top-mounted freezer (TMF). For a quantitative comparison of the operational performance, an FDU and an EPS duct were installed alternately in a refrigerator operated under the same conditions and analyzed in terms of internal temperature variation and operational characteristics. When the EPS duct was replaced by the FDU, the temperature deviation measured during a defrosting operation was observed to become smaller. Moreover, during a power outage, the refrigerator with the FDU released heat owing to the phase change of the PCM, thereby preventing temperature rise inside the refrigerator.

Description: Energies, Vol. 11, Pages 2016: The Synergies of Shared Autonomous Electric Vehicles with Renewable Energy in a Virtual Power Plant and Microgrid Energies doi: 10.3390/en11082016 Authors: Riccardo Iacobucci Benjamin McLellan Tetsuo Tezuka The introduction of shared autonomous electric vehicles (SAEVs), expected within the next decade, can transform the car into a service, accelerate electrification of the transport sector, and allow for large scale control of electric vehicle charging. In this work, we investigate the potential for this system to provide aggregated storage when combined with intermittent renewable energy sources. We develop a simulation methodology for the optimization of vehicle charging in the context of a virtual power plant or microgrid, with and without grid connection or distributed dispatchable generators. The model considers aggregate storage availability from vehicles based on transport patterns taking into account the necessary vehicle redistribution. We investigate the case of a grid-connected VPP with rooftop solar and the case of a isolated microgrid with solar, wind, and dispatchable generation. We conduct a comprehensive sensitivity analysis to study the effect of several parameters on the results for both cases.

Description: Energies, Vol. 11, Pages 2015: Energy-Efficient Clusters for Object Tracking Networks Energies doi: 10.3390/en11082015 Authors: Yang-Hsin Fan Smart cities have hundreds of thousands of devices for tracking data on crime, the environment, and traffic (such as data collected at crossroads and on streets). This results in higher energy usage, as they are recording information persistently and simultaneously. Moreover, a single object tracking device, on a corner at an intersection for example has a limited scope of view, so more object tracking devices are added to broaden the view. As an increasing number of object tracking devices are constructed on streets, their efficient energy consumption becomes a significant issue. This work is concerned with decreasing the energy required to power these systems, and proposes energy-efficient clusters (EECs) of object tracking systems to achieve energy savings. First, we analyze a current object tracking system to establish an equivalent model. Second, we arrange the object tracking system in a cluster structure, which facilitates the evaluation of energy costs. Third, the energy consumption is assessed as either dynamic or static, which is a more accurate system for determining energy consumption. Fourth, we analyze all possible scenarios of the object’s location and the resulting energy consumption, and derive a number of formulas for the fast computation of energy consumption. Finally, the simulation results are reported. These results show the proposed EEC is an effective way to save energy, compared with the energy consumption benchmarks of current technology.

Description: Energies, Vol. 11, Pages 2014: Effect of Sodium Chloride and Thiourea on Pollutant Formation during Combustion of Plastics Energies doi: 10.3390/en11082014 Authors: María E. Iñiguez Juan A. Conesa Andrés Fullana Thermal decomposition of different samples containing a mixture of plastics (polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), and nylon) combined with NaCl and metal oxides (Fe2O3, CuO) was studied under an air atmosphere at 850 °C using a reactor, followed by analysis of the evolved products. Combustion runs were performed to study how the presence of such compounds influences the production of pollutants. Here, we report the analyses of the emissions of the main gases, as well as volatiles and semivolatiles, including polyaromatic hydrocarbons (PAHs), polychlorinated benzenes and phenols, and polybrominated phenols. Results show that the production of chlorinated pollutants did not increase in the presence of NaCl, but the presence of other metals during the decomposition led to the production of a great amount of pollutants. In this regard, the emission of chlorinated phenols increased from 110 to ca. 250 mg/kg when the sample included a small quantity of a transition metal oxide. Additionally, the presence of an inhibitor—thiourea (TUA)—was tested. Results confirm that adding TUA to the sample reduced these emissions to a considerable extent, with the emission of chlorinated phenols amounting to 65 mg/kg.

Description: Energies, Vol. 11, Pages 2013: Establishment of an Improved Material-Drilling Power Model to Support Energy Management of Drilling Processes Energies doi: 10.3390/en11082013 Authors: Shun Jia Qingwen Yuan Wei Cai Qinghe Yuan Conghu Liu Jingxiang Lv Zhongwei Zhang Drilling processes, as some of the most widely used machining processes in the manufacturing industry, play an important role in manufacturing process energy-saving programs. However, research focus on energy modeling of drilling processes, especially for the modeling of material-drilling power, are really scarce. To bridge this gap, an improved material-drilling power model is proposed in this paper. The obtained material-drilling power model can improve the accuracy of the material-drilling power and lay a good foundation for energy modeling and optimization of drilling processes. Finally, experimental studies were carried out on an XHK-714F CNC machining center (Hangzhou HangJi Machine Tool Co., Ltd., Hangzhou, China) and a JTVM6540 CNC milling machine (Jinan Third Machine Tool Co., Ltd., Jinan, China). The results showed that predictive accuracies with the proposed model are generally higher than 96% for all the test cases.

Description: Energies, Vol. 11, Pages 2012: Estimation of Load Pattern for Optimal Planning of Stand-Alone Microgrid Networks Energies doi: 10.3390/en11082012 Authors: Chang Koo Lee Byeong Gwan Bhang David Kwangsoon Kim Sang Hun Lee Hae Lim Cha Hyung Keun Ahn This paper proposes a method for estimating the load pattern for optimal planning of stand-alone renewable microgrids and verifies when the basic data for microgrid design are limited. To estimate a proper load pattern for optimal microgrid design when the data obtained in advance are insufficient, the least squares method is used to compare the similarity of annual power consumption between the subject area and eight islands in Korea whose actual load patterns were previously obtained. Similarity is compared in terms of annual (every month), seasonal, bi-monthly, and monthly averages. To verify the validity of the proposed estimation method, the applied proposed estimation method is used for two islands that have already installed a microgrid consisting of photovoltaic, wind power, energy storage systems, and diesel generators. In comparing the actual data from the two islands, the costs of electricity in terms of microgrid operations show improvements of 37.2% and 29.8%, respectively.

Description: Energies, Vol. 11, Pages 2008: Short-Term Load Forecasting of Natural Gas with Deep Neural Network Regression † Energies doi: 10.3390/en11082008 Authors: Gregory D. Merkel Richard J. Povinelli Ronald H. Brown Deep neural networks are proposed for short-term natural gas load forecasting. Deep learning has proven to be a powerful tool for many classification problems seeing significant use in machine learning fields such as image recognition and speech processing. We provide an overview of natural gas forecasting. Next, the deep learning method, contrastive divergence is explained. We compare our proposed deep neural network method to a linear regression model and a traditional artificial neural network on 62 operating areas, each of which has at least 10 years of data. The proposed deep network outperforms traditional artificial neural networks by 9.83% weighted mean absolute percent error (WMAPE).

Description: Energies, Vol. 11, Pages 2024: Coupled Fluid-Thermal Analysis for Induction Motors with Broken Bars Operating under the Rated Load Energies doi: 10.3390/en11082024 Authors: Ying Xie Jinpeng Guo Peng Chen Zhiwei Li Thermal stress of the rotor in a squirrel cage induction motor is generated due to the temperature rise, it is also one of the factors causing the broken bar fault because the structure of the rotor would be destroyed if the stress of the rotor bars exceed the strength limit. The coupled fluid-thermal analysis for the induction motor with healthy and broken bar rotors is performed in this paper. Much concern has been committed to establishment of the fluid model on the basis of computational fluid dynamic (CFD) theory. The heat field of the prototypes is analysed so that the effect of the asymmetrical rotor on the motor heat performance can be investigated in depth. Eventually, the efficiency of the presented model and method, for the totally enclosed fan cooled (TEFC) induction motor, can be verified through experimental results. In addition, this paper reports a quantitative analysis of the heat flux distribution of the fault rotor, and the heat flux density of the bars is investigated in detail. Then, the part most likely to break in the rotor as a result of the thermal load is identified.