ALBERT

Description: Voyager 1 images show 14 volcanic centers wholly or partly within the Kane Patera quadrangle of Io, which are divided into four major classes: (1) shield with parallel flows; (2) shield with early radial fan shapd flows; (3) shield with radial fan shaped flows, surfaces of flows textured with longitudinal ridges; and (4) depression surrounded by plateau-forming scarp-bounded, untextured deposits. The interpretation attempted here hinges largely on the ability to distinguish lava flows from pyroclastic flows by remote sensing.

Description: Structural and tectonic interpretations of planetary surfaces rely strongly on visual determination of regional structural grain. This grain can be very complex and confusing, and sorting out of discrete trends in time and space is of utmost importance. This study is a test of these techniques applied to a well known area having several discrete structural grains. In the Bighorn Basin region of Wyoming, a largely overlooked N10E structural grain has been verified with detailed structural analysis and indicates a significant change in stress orientation at the end of the Laramide orogeny.

Description: Tectoism in the Valles Marineris appears to have been accompanied by volcanism. The proposed volcanic features, though probably contemporaneous with the gigantic ones in the Tharsis area, are composed of small, mafic and, possibly, somewhat larger felsic flows. The size of these features is similar to that of volcanic flows on the Earth.

Description: Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

Description: The design and operations of a low cost, high rate thermal cycling facility designed for LEO conditions is described. Thermal cycling facilities were constructed with various design criteria. Some were designed to duplicate as closely as possible the conditions a cell or module would encounter while in orbit about the Earth. A typical facility to perform this type of cycling was a large vacuum system with liquid nitrogen cooled walls. The cells were heated by an AMO spectrum solar simulator, then a shutter was closed allowing the cells to give up their heat to the cold walls. This system was good at duplicating the orbital conditions but was slow and very costly to operate. Other systems used a gas atmosphere and heated the cells with radiant heat and cooled the cells by moving them into close proximity to a cold plate. The systems greatly increased the cycle times. Other systems moved the heating and cooling atmosphere into and out of the test areas and achieved reasonable cycle rates. All these systems, however, are expensive to operate.

Description: The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

Description: The solar array for the San Marco D/L spacecraft is described and the performance of 4 GaAs solar cell panels are examined. In comparison to the typical Si solar cell panel for San Marco D/L, it is shown that each GaAs solar cell panel provides at least 23 percent more specific power at maximum output and 28 deg C. Also described here, are several measurements that will be made to evaluate the relative performance of Si and GaAs solar cell panels during the San Marco D/L flight.

Description: The results of heteroepitaxial growth of GaAs and GaAlAs directly on Si are presented, and applications to new cell structures are suggested. The novel feature is the elimination of a Ge lattice transition region. This feature not only reduces the cost of substrate preparation, but also makes possible the fabrication of high efficiency monolithic cascade structures. All films to be discussed were grown by organometallic chemical vapor deposition at atmospheric pressure. This process yielded reproducible, large-area films of GaAs, grown directly on Si, that are tightly adherent and smooth, and are characterized by a defect density of 5 x 10(6) power/sq cm. Preliminary studies indicate that GaAlAs can also be grown in this way. A number of promising applications are suggested. Certainly these substrates are ideal for low-weight GaAs space solar ells. For very high efficiency, the absence of Ge makes the technology attractive for GaAlAs/Si monolithic cascades, in which the Si substrates would first be provided with a suitable p/n junction. An evaluation of a three bandgap cascade consisting of appropriately designed GaAlAs/GaAs/Si layers is also presented.

Description: Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Description: A short circuit current (I sub sc) degradation model for gallium arsenide (GaAs) solar cells irradiated by protons from low energy to 100 MeV was developed. This model was found to be satisfactory in predicting the I sub sc degradation of GaAs cells, but not that of silicon (Si) cells. A modification to the aforementioned model that preserves the optical wavelength dependency in the photogeneration of minority carrier pairs was described herein. Spectral Si and GaAs response and I sub sc for the Si and GaAs solar cells were discussed, and also were presented in graph form. The overall predictability of the modified model was deemed to be satisfactory.

Description: Manufacturing technology for mass producing high efficiency GaAs solar cells is discussed. A progress using a high throughput MO-CVD reactor to produce high efficiency GaAs solar cells is discussed. Thickness and doping concentration uniformity of metal oxide chemical vapor deposition (MO-CVD) GaAs and AlGaAs layer growth are discussed. In addition, new tooling designs are given which increase the throughput of solar cell processing. To date, 2cm x 2cm AlGaAs/GaAs solar cells with efficiency up to 16.5% were produced. In order to meet throughput goals for mass producing GaAs solar cells, a large MO-CVD system (Cambridge Instrument Model MR-200) with a susceptor which was initially capable of processing 20 wafers (up to 75 mm diameter) during a single growth run was installed. In the MR-200, the sequencing of the gases and the heating power are controlled by a microprocessor-based programmable control console. Hence, operator errors can be reduced, leading to a more reproducible production sequence.

Description: Various coatings developed in the FRG (i.e., second-surface mirrors with interference filters with and without conductive layers, conductive layers on solar-cell covers, and selective absorber coatings) have been qualified by accelerated tests under simulated space environment conditions. Experiments with coatings and solar cells have shown, however, that the thermo-optical behavior can differ considerably when performed on the ground and in space because of the great difficulty in simulating the space environment realistically. The objective of this experiment is to qualify these coatings under realistic space environment conditions. In addition, the experiment will provide design criteria, techniques, and test methods to insure control of the combined space and spacecraft environment effects, such as contamination, electrical conductance, and optical degradation, on the coatings. Data to be measured include the temperature of the samples, the electrical resistance of the conductive layers of the samples, the short circuit current of the solar-cell modules, and the deposition of contaminants on the samples (using quartz crystal microbalances (QCM's)).

Description: The objective of this experiment is to evaluate the synergistic effects of the space environment on various solar-array materials, including solar cells, cover slips with various antireflectance coatings, adhesive, encapsulants, reflector materials, substrate strength materials, mast and harness materials, structural composites, and thermal control treatments. The experiment is passive and consists of an arrangement of material specimens mounted in a 3-in.-deep peripheral tray. The effects of the space environment on the specimens will be determined by comparison of preflight and postflight measurements of mechanical, electrical, and optical properties.

Description: Significant new geologic information has been revealed by comparing 1:5 million scale geologic maps of the equatorial zone quadrangles of Mercury (H-6, H-7 and H-8) to Earth-based elevation profiles and surface reflectivity maps of Mercury obtained in the early 1970's at the Arecibo (PR) and Goldstone (CA) radar facilities. These data consist of 23 Goldstone images and profiles of polarized return data at 12.5-cm wavelength and one Arecibo profile. Radar data with 150-m vertical accuracy and 10- to 20-km horizontal resolution are available for areas between latitudes 13 N. and 11 S. In general, these data sets show excellent correlation between: (1) relative elevation and roughness differences that are reflected by mapped geologic contacts; (2) mapped ridges and scarps that display distinctive radar signatures; and (3) position and morphology of crater-and-basin topographic elements. Inferences can also be drawn about topographic and geologic terrain beyond the area imaged by Mariner 10 cameras.

Description: On Mars, the association of gullied escarpments and chaotic terrain is evidence for failure and scarp retreat of poorly consolidated materials. Some martian gullies have no surface outlets and may have drained through subterranean channels. Similar features, though on a much smaller scale, can be seen in alluvium along terrestrial river banks in semiarid regions, such as the Rio Puerco Valley of central New Mexico. Many of the escarpments along the Rio Puerco are developing through formation of collapse gullies, which drain through soil pipes. Gully development can be monitored on aerial photographs taken in 1935, 1962, and 1980. A regression model was developed to quantify gully evolution over a known time span. Soil pipes and their associated collapse gullies make recognizable signatures on the air photos. The areal extent of this signature can be normalized to the scarp length of each pipe-gully system, which makes comparisons between systems possible.

Description: Geomorphic studies of impact structures in central Australia are being used to understand the complexities of fluvial dissection in the heavily cratered terrains of Mars. At Henbury, Northern Territory, approximately 12 small meteorite craters have interacted with a semiarid drainage system. The detailed mapping of the geologic and structural features at Henbury allowed this study to concentrate on degradational landforms. The breaching of crater rims by gullies was facilitated by the northward movement of sheetwash along an extensive pediment surface extending from the Bacon Range. South-facing crater rims have been preferentially breached because gullies on those sides were able to tap the largest amounts of runoff. At crater 6 a probable rim-gully system has captured the headward reaches of a pre-impact stream channel. The interactive history of impacts and drainage development is critical to understanding the relationships in the heavily cratered uplands of Mars. Whereas Henbury craters are younger than 4700 yrs. B.P., the Gosses Bluff structure formed about 130 million years ago. The bluff is essentially an etched central peak composed of resistant sandstone units. Fluvial erosion of this structure is also discussed.

Description: Eastern Acidalia Planitia contains a wide variety of terrain types on which are thousands of subkilometer volcanoes. Apparent morphometric variations were previously reported as a function of terrain type for the cones in the Cydonia area and extended to the rest of Acidalia for which high resolution Viking imagery exist. Crater counts are included for the six types of plains identified, density distributions of subkilometer cones found on each type of terrain, and orphometric data by morphological subclass as a function of terrain for more than 1400 cones.

Description: Preliminary mapping shows East Butte to be a single, large cumulo-dome composed dominantly of rhyolite which can be classified into three main groups based on color and structure. The rhyolite of East Butte is aphanitic with phenocrysts of sanidine and quartz which vary from 1 to 5 mm in length. Vesicular reddish black inclusions of basalt up to 10 cm in length, found in all varieties of the East Butte rhyolites are believed to have originated from fragmentation of the basalt walls of the conduit by rhyolitic magma as it was emplaced. Most of the inclusions contain plagioclase phenocrysts. These phenocrysts measure up to 1 to 2 cm in length and have a typical euhedral, tabular habit. A 250-m diameter depression which has the appearance of a crater is located at the top of East Butte. Evidence supporting the fact that the depression is a crater is displayed by three small (3 to 5 m in height) mounds of massive rhyolite which border the depression.

Description: Some of the geological relationships observed in the Mauna Loa sulfur flow may apply in considering volcanic processes on Io. Given the presence of sulfur/sulfur compounds in the eruption plumes and on the surface of Io, it is likely that extensive secondary deposits of sulfur exist, some of which may be of fumarolic origin and analogous to the Mauna Loa deposit. Given the likelihood of silicate volcanism of Io based on the inferred material properties of some flows, and the attendant high temperatures for silicate volcanism, it is likely that the secondary surface deposits of sulfur would have been mobilized without being heated to the high viscosity stage. Mobilized sulfur flows on Io may flow long distances as a result of: (1) low viscosities in the melting range; (2) sustained effusion resulting from continued heating source area; (3) continued remobilization within the flow as a consequence of surges from the source; and (4) extension via lava tubes, or similar conduits through which there is little heat loss. Sulfur flows may form a relatively thin veneer over silicate flows and other surface units, given their fluidity and low mobilization temperature. Active splashing and splattering may spread sulfur over a wider area contributing the bright blooms observed in association with some Ionian flows.

Description: Perhaps the greatest chance for exhumation, or burial, of a landscape by terrestrial processes exists near the boundaries of the climatic belts. In the Southern Hemisphere, there is comparatively little land area within Budel's zone of extra-tropical valley formation, which contains most of the examples of exhumed topography in the Northern Hemisphere. The only examples of resurrected landforms that occur within Budel's tropical zone are located near the boundary of this zone, where climate may have changed during the Pleistocene. The ages of exhumed landforms sampled are not equally distributed through geologic time. Most of the exhumed features were created either during the Precambrian or the Tertiary periods which are commonly cited as episodes of significant landform development.

Description: The Dry Valleys of Antarctica are examples of polar deserts which are rare geological features on the Earth. Such deserts typically have high salinities associated with their closed-basin waters and on many surficial materials throughout them. In order to examine the possible sources for the salts observed in association with the soils in the Dry Valleys. The chloride and bromide concentrations of the water leachates from 58 soils and core samples were measured. The Cl/Br ratio for seawater is 289 and ratios measured for most of the 58 soils studied (greater than 85% of the soils studied) was larger than the seawater ratio (ratios typically were greater than 1000 and ranged up to 50,000). The enrichment in Cl relative to Br is strong evidence that the alts present within the soils were derived from seawater during ordinary evaporation processes, and not from the deposition of Cl and Br from aerosols or from rock weathering as has often been suggested.

Description: Field studies of terrestrial landforms and the processes that shape them provide new directions to the study of planetary features. Investigations discussed address principally mudflow phenomena and drainage development. At the Valley of 10,000 Smokes (Katmai, AK) and Mount St. Helens, WA, studies of the development of erosional landforms (in particular, drainage) on fresh, new surfaces permitted analysis of the result of competition between geomorphic processes. Of specific interest is the development of stream pattern as a function of the competition between perennial seepage overland flow (from glacial or groundwater sources), ephemeral overland flow (from pluvial or seasonal melt sources), and ephemeral/perennial groundwater sapping, as a function of time since initial resurfacing, material properties, and seasonal/annual environmental conditions.

Description: Desert pavement is a general term describing a surface that typically consists of a thin layer of cm-sized rock fragments set on top of a layer of finer material in which no fragments are found. An understanding of desert pavement is important to planetary geology because they may play a major role in the formation and visibility of various aeolian features such as wind streaks, which are important on Mars and may be important on Venus. A field study was conducted in Amboy, California to determine the formation mechanism of desert pavements. The probable sequence of events for the formation and evolution of a typical desert pavement surface, based on this experiment and the work of others, is as follows. Starting with a layer of surface material consisting of both fine particles and rock fragments, aeolian deflation will rapidly erode the surface until an armored lag is developed, after which aeolian processes become less important. The concentration of fragments then slowly increases as new fragments are brought to the surface from the subsurface and as fragments move downslope by sheet wash. Sheet wash would be responsible for removing very fine particles from the surface and for moving the fragments relative to one another, forming interlocks.

Description: The design and structural properties of a low concentration ratio solar array are discussed. The assembled module consists of six interconnected containers which are compactly stowed in a volume of 3.24 m(3) for delivery to orbit by the shuttle. The containers deploy in accordian fashion into a rectangular area of 19.4 x 68 meters and can be attached to the user spacecraft along the longitudinal centerline of the end container housing. Five rotary incremental actuators requiring about 8 watts each will execute the 180-degree rotation at each joint. Deployable masts (three per side) are used to extend endcaps from the housing in both directions. Each direction is extended by three masts requiring about 780 watts for about 27 minutes. Concentrator elements are extended by the endcaps and are supported by cable systems that are connected between the housings and endcaps. These power generating elements contain reflector panels which concentrate light onto the solar panels consisting of an aluminum radiator with solar cells positioned within the element base formed by the reflectors. A flat wire harness collects the power output of individual elements for transfer to the module container housing harnesses.

Description: Field studies of terrestrial landforms and the processes that shape them provide new directions to the study of planetary features. These studies, conducted in Iceland and in Antarctica, investigated physical and chemical weathering mechanisms and rates, eolitan processes, mudflow phenomena, drainage development, and catastrophic fluvial and volcanic phenomena. Continuing investigations in Iceland fall in three main catagories: (1) catastrophic floods of the Jokulsa a Fjollum, (2) lahars associated with explosive volcanic eruptions of Askja caldera, and (3) rates of eolian abrasion in cold, volcanic deserts. The ice-free valleys of Antarctica, in particular those in South Victoria Land, have much is common with the surface of Mars. In addition to providing independent support for the application of the Iceland findings to consideration of the martian erosional system, the Antarctic observations also provide analogies to other martian phenomena. For example, a family of sand dunes in Victoria Valley are stabilized by the incorporation of snow as beds.

Description: Development of drainage networks by erosion by emergent groundwater (sapping) is being modelled by a combination of laboratory experiments and theoretical modelling. Miniature drainage networks formed in fine-grained sediments share many morphologic characteristics of Martian and terrestrial networks suspected to be formed by sapping processes. A larger and better instrumented sapping box was constructed to further explore the processes of sapping and the morphology of resulting networks. The experiments to be conducted in the sapping box will investigate the roles of several factors in controlling network morphology. The mechanics of sapping of fine-grained sediments were investigated in experiments in a two-dimensional sapping chamber and through development of a theoretical model. Results of extensive tests on sapping erosion of fine-grained, cohesionless sediment were analyzed with a theoretical model of the mechanics of sapping erosion and transport.

Description: The 18 May 1980 eruption of Mount St. Helens was initiated by a massive rockslide-debris avalanche which completely transformed the upper 25 km of the North Fork Toutle River valley. The debris was generated by one of the largest gravitational mass movements ever recorded on Earth. Moving at an average velocity of 35 m/s, the debris avalanche buried approximately 60 sq km of terrain to an average depth of 45 m with unconsolidated, poorly sorted volcaniclastic material, all within a period of 10 minutes. Where exposed and unaltered by subsequent lahars and pyroclastic flows, the new terrain surface was characterized predominantly by hummocks, closed depressions, and the absence of an identifiable channel network. Following emplacement of the debris avalanche, a complex interrelationship of fluvial and mass wasting processes immediately began operating to return the impacted area to an equilibrium status through the removal of material (potential energy) and re-establishment of graded conditions. In an attempt to chronicle the morphologic evolution of this unique environmental setting, a systematic series of interpretative maps of several selected areas was produced. These maps, which document the rate and character of active geomorphic processes, are discussed.

Description: Pressure ridges are surface features on basaltic lava flows and, as with other surface features, they may be related to the emplacement of a flow and the rheological properties of the lava. Since many ridges are of sufficient size to be detected on high resolution orbital images, an understanding of pressure ridges could provide a means for interpreting volcanic flows on other terrestrial planets. Some proposed formation mechanisms are reviewed and three different types of pressure ridges are identified on the basis of morphology. Type 1 ridges are the most common and are associated with multiple flow unit pahoehoe in which the ridges are embayed by secondary toe fed lava. They tend to be restricted to wider sections or margins of the flow and to be oriented longitudinal to flow direction; however, oblique or transverse orientation is not uncommon. Bulbous squeeze ups are common within cracks and may reflect relative timing of crack formation. The interior structure of type 1 ridges consists of an upper slab section which generally contains columnar joints and a lower massive section with an irregular surface. This basic distinction may mark the thickness of the surface crust when ridge formation was initiated. Type 2 ridges occur in association with type 1 and are very similar with the exception of the secondary squeeze out material. Instead of only filling cracks, the secondary material on these ridges originated from underneath a thin crust and flowed as toes or channels from the top and sides of the ridge. Type 3 ridges have much steeper sides (almost vertical at the top) than the other types. Medial cracks are very wide and the crack walls are convex upward. No squeeze ups are present. The main difference between type 3 and the others may be reflection of viscosity.

Description: A model for the radiative cooling of thermally well mixed lava flows is presented and the relationship between effusion rate and length and area is analyzed. If radiative cooling is the prime mode of heat loss for a lava flow, one should expect to see a stronger correlation between the effusion rate and the plan area of the flow, than between effusion rate and just flow length. Different flows on a single volcano with differing initial temperatures, volatile content, and gross compositions should yield different areas for a given effusion rate. Likewise, a range of slopes for the relationship between effusion rate and flow area should result from comparisons between different volcanoes. As a test of these ideas, available data on the effusion rates, lengths, and areas of Hawaiian and Etnean flow is studied. It was found that: (1) the effusion rate/area correlation was statistically more significant than the correlation between effusion rate and length for four out of the five eruption episodes which met the necessary criteria of more than three individual flows with area, length, and effusion rate independently measured; (2) that there exists a minimum length and area for a given effusion rate, reflecting competition between overall characteristic proportionality between effusion rate and flow length, width, and area.

Description: Between 1217 and 1620 hours (PDT), on May 18, 1980, the magmatic eruption column of Mount St. Helens formed an ash fountain and pyroclastic flows dominated the eruption process over tephra ejection. Eurption-rate pulsations generally increased to a maximum at 1600 to 1700 hrs. After 1620 hrs, the eruption assumed an open-vent discharge with strong, vertical ejection of tephra. Relative eruption rates (relative mass flux rates) of the pyroclastic flows were determined by correlating sequential photographs and SLAR images, obtained during the eruption, with stratigraphy and surface morphology of the deposits.

Description: Reexamination of Upheaval Dome in the Canyonlands National Park, Utah, shows that the structure of this remarkable feature conforms with that expected for a deeply eroded astrobleme. The structure is definitely not compatible with an origin due simply to plastic flowage of salt and other rocks in the underlying Paradox Formation. The most strongly deformed rocks are bounded by a series of circumferential listric faults. The convergent displacement of the rocks corresponds to the deformation that results from collapse of a transient cavity produced by high speed impact. From considerations of the probable depth of exposure of the impact structure and upward extrapolation of the listric faults, the final collapsed crater is estimated to be about 8 to 10 km in diameter; the impacting body was on the order of 0.5 km in diameter.

Description: A brief synopsis of the low Earth orbit (LEO) satellite environment is presented including neutral and ionic species. Two ground based atomic and molecular beam instruments are described which are capable of simulating the interaction of spacecraft surfaces with the LEO environment and detecting the results of these interactions. The first detects mass spectrometrically low level fluxes of reactively and nonreactively surface scattered species as a function of scattering angle and velocity while the second ultrahigh velocity (UHV) molecular beam, laser induced fluorescence apparatus is capable of measuring chemiluminescence produced by either gas phase or gas-surface interactions. A number of proposed experiments are described.

Description: A brief review of atmospheric composition in low Earth orbit is presented. The flux of ambient atomic oxygen incident on a surface orbiting in this environment is described. Estimates are presented of the fluence of atomic oxygen to which satellite surfaces in various orbits are exposed.

Description: Participants expressed more interest in GaAs cells than in Si cells. For silicon cells, the beginning of life efficiency is not a major problem but more research is needed in the end of life efficiency. The beginning of life efficiency of GaAs cells must be brought up to 20% at AMO. More proton damage tests must be conducted. Liquid phase epitaxy technology is current but chemical vapor deposition technology is more flexible. There are no obvious problems in limiting process yields. Technology transfer should occur when market demands are generated.

Description: Principles and design considerations of IR transparent solar arrays are discussed. Optimization of performance of flexible solar arrays was studied. Measured solar absorptance as low as alpha s = 0.59 was achieved which leads to a predicted BOL power density of 182.7 = W/square meters. Advanced array concepts, system level cascaded panels, and transparent rigid panels are proposed and expected benefits discussed.

Description: A number of structurally efficient configurations for wing-type solar arrays are developed by a combination of deepening the planform of the blanket and structure and by partitioning the blanket with battens and frequent attachments to the support structure. This technique reduces the tension required to avoid a low natural frequency for the blanket, and the load reduction results in a lighter structure. The use of three different structures are investigated: the Astromast, the Extendible Support Structure (ESS), and a new beam called the STACBEAM (Stacking Triangular Articulated Compact Beam) and their relative performances are compared. The investigation of the STACBEAM is emphasized because its sequential deployment is more reliable for very long systems, and its linear deployment facilitates local attachments to the blanket and the development of a low mass deployer.

Description: Structurally efficient ways to support the large solar arrays (3,716 square meters which are currently considered for space station use) are examined. An erectable truss concept is presented for the on orbit construction of winged solar arrays. The means for future growth, maintenance, and repair are integrally designed into this concept. Results from parametric studies, which highlight the physical and structural differences between various configuration options are presented. Consideration is given to both solar blanket and hard panel arrays.

Description: A miniaturized Cassegrainian concentrator (MCC) solar array system is examined to assess the practicality of assembling the basic MCC element into a total array system capable of producing multi-hundred kilowatts of power for Space Platform/Space Station or other low Earth orbit long lifetime missions. Preliminary mechanical and electrical subsystems are developed in order to determine first order performance characteristics. Results of the study support the feasibility of a 100-kilowatt MCC array system with beginning-of-life (BOL) performance of 160 watts per square meter and 28 W/kg. The performance numbers are based on 20 percent efficient (at operating temperature) solar cells and 0.25-millimeter thick electroformed nickel optics. These performance numbers can be improved upon significantly with the development of higher efficiency solar cells and/or lighter weight optics.

Description: High-efficiency, monolithic, two-color, three-terminal solar cells were fabricated by a novel growth technique, vacuum metal-organic chemical vapor deposition. The technique uses the expensive metal alkyls efficiently and toxic gases sparingly. The fact that the outer chamber is constructed of nonbreakable stainless steel is an attractive safety feature associated with this deposition system.

Description: Computer analysis was used to determine the AMO conversion efficiency of single-junction crystalline cells, two-cell and three-cell crystalline tandem structures operating under 100 suns and at 80 C. For optimally designed devices, the calculated efficiencies are 24% for single-junction cells, 33 to 35% for two-cell tandem structures, and 37 to 39% for three-cell tandem structures. Practical efficiencies are expected to be about 15 relative percentage points lower in each case.

Description: The short-circuit current reduction in GaAs shallow junction heteroface solar cells was calculated according to a simplified solar cell damage model in which the nonuniformity of the damage as a function of penetration depth is treated explicitly. Although the equivalent electron fluence was not uniquely defined for low-energy monoenergetic proton exposure, an equivalent electron fluence is found for proton spectra characteristic of the space environment. The equivalent electron fluence ratio was calculated for a typical large solar flare event for which the proton spectrum is PHI(sub p)(E) = A/E(p/sq. cm) where E is in MeV. The equivalent fluence ratio is a function of the cover glass shield thickness or the corresponding cutoff energy E(sub c). In terms of the cutoff energy, the equivalent 1 MeV electron fluence ratio is r(sub p)(E sub c) = 10(9)/E(sub c)(1.8) where E(sub c) is in units of KeV.

Description: Some n(+)/p cells in which lithium is introduced as a counterdopant, by ion-implantation, into the cell's boron-doped p-region were studied. To determine if the cells radiation resistance could be significantly improved by lithium counterdoping. Defect behavior was related to cell performance using deep level transient spectroscopy. Results indicate a significantly increased radiation resistance for the lithium counterdoped cells when compared to the boron doped 1 ohm-cm control cell. The increased radiation resistance of the lithium counterdoped cells is due to the complexing of lithium with divacancies and boron. It is speculated that complexing with oxygen and single vacancies also contributes to the increased radiation resistance. Counterdoping silicon with lithium results in a different set of defects.

Description: Telemetry from the Living Plume Shield's gallium arsenide solar panel experiment was evaluated to determine degradation. The data were culled to preclude spurious results from possible shadowing or inaccurate measurements on a cold array. Two independent methods were then used to obtain the maximum power points and the various characteristics of the solar array. Fill factor, open circuit voltage, short circuit current, and series and shunt resistances were examined. The data analysis concluded that, to date, nearly all of the solar array degradation is due to the reduction in the short circuit current.

Description: The radiation tolerance of the following three low resistivity, high voltage silicon solar cells was investigated: (1) the COMSAT MSD (multi-step diffused) cell, (2) the MinMIS cell, and (3) the MIND cell. A description of these solar cells is given along with drawings of their configurations. The diffusion length damage coefficients for the cells were calculated and presented. Solar cell spectral response was also discussed. Cells of the MinMIS type were judged to be unsuitable for use in the space radiation environment.

Description: Gallium Arsenide (GaAs) solar cells are viewed as a potential primary power source on certain future Earth orbiting satellites. However, the relative merits of gallium arsenide over silicon in a space radiation environment are largely unknown because a general degradation model for gallium arsenide does not exist. The results of a test simulating the proton radiation environment existing in a polar orbit and the concomitant effects on GaAs and thin silicon (Si) solar cells are presented. The objectives and methodology of the simulation test were discussed. The electrical characteristics of GaAs and Si solar cells are given in graph form. It was concluded that GaAs cells are viable for use on satellites in low Earth orbit.

Description: Significant discrepancies have been observed between predicted and actual in-orbit silicon solar array degradation in orbits other than LEO (low Earth orbits) and GEO (geosynchronous orbit). These discrepancies have been diagnosed to arise probably from a combination of a lack of appropriate solar cell test data and from inadequacies in the models that relate the unidirectional and mono-energetic proton test data to the omnidirectional flux-energy spectra actually found in orbit. Relative damage coefficients and solar cell power outputs were discussed, and also were presented in graph form. Silicon and gallium arsenide solar cells were considered.

Description: The radiation damage of solar cells has become a prime concern to the U.S. Air Force due to longer satellite lifetime requirements. Flight experiments were undertaken on the Navy Living Plume Shield (LPS) satellite and the NASA/Air Force Combined Release and Radiation Effects Satellite (CRRES) to complement existing radiation testing. Each experiment, the rationale behind it, and its approach and status are presented. The effect of space radiation on gallium arsenide (GaAs) solar cells was the central parameter investigated. Specifications of the GaAs solar cells are given.

Description: A computer program, SCAP2D (Solar Cell Analysis Program in 2-Dimensions), is used to evaluate the Etched Multiple Vertical Junction (EMVJ) and grating solar cells. The aim is to demonstrate how SCAP2D can be used to evaluate cell designs. The cell designs studied are by no means optimal designs. The SCAP2D program solves the three coupled, nonlinear partial differential equations, Poisson's Equation and the hole and electron continuity equations, simultaneously in two-dimensions using finite differences to discretize the equations and Newton's Method to linearize them. The variables solved for are the electrostatic potential and the hole and electron concentrations. Each linear system of equations is solved directly by Gaussian Elimination. Convergence of the Newton Iteration is assumed when the largest correction to the electrostatic potential or hole or electron quasi-potential is less than some predetermined error. A typical problem involves 2000 nodes with a Jacobi matrix of order 6000 and a bandwidth of 243.

Description: Several modifications were made to an infinite solution liquid phase epitaxy system that help fabricate both GaAs-based cells and thin cells that effectively reduce power-to-weight ratio for space applications. The most important development is the multiwell crucible for multilayer growth. Using a split crucible in one system, as many as five layers were grown in succession with varying Al levels and dopants. The structures grown were used to produce thin GaAs cells only 10 to 20 microns thick and also to grow cascade cell components. Results of these studies are presented and their applications to the future development of GaAs-based cells are discussed.

Description: A fabrication process for structurally stable thin solar cell wafers that produce good power output after irradiation is described. The fabrication process is as follows. A 6 mil, circular wafer is oxidized on both sides. One side is then patterned with a rectangular array of holes in the oxide that are nominally 75 mils square and separated by 2 mil spacings. Wells are then etched into the silicon with KOH to a depth of 4 mils, leaving a 2 mil, unetched thickness. Two areas on the surface are left unetched to provide pads for bonding or testing. All oxide is then removed and the rest of the processing is normal; the unetched face is used as the illuminated face. When all other processing is complete, a 2 X 2 cm cell is sawed from the starting wafer leaving a border that is approximately 10 mils wide. The effective thickness, determined by weighing an unmetallized sample, of such a cell is about 2.4 mil.

Description: The advanced photovoltaics-related experiments for investigating a portion of the solar spectrum and the effect of the space environment on photovoltaics. The information will be used to provide correlation between space and ground testing and also to provide for more accurate performance measurement in the laboratory. Specific objectives of these experiments are to provide information on the performance and endurance of advanced and conventional solar cells, to improve reference standards for photovoltaic measurements, and to measure the energy distribution in the extraterrestrial solar spectrum. Data to be obtained will include temperatures and short-circuit current of the samples. Six-point current-voltage (I-V) characteristics will be obtained for selected samples. These data will be recorded once a day during the flight. Orbit data will be correlated with preflight and postflight measurement of the samples.

Description: Three-dimensional finite element modeling techniques are used to synthesize geodetic and seismological results for 1979 Imperial Valley earthquake. The strategy pursued consists of two principal steps. In the first step, the seismologically-derived coseismic fault slip is taken as a function of position in the fault plane and is applied directly to the three-dimensional dislocation model. In the second step, a physical model of stresses and constitutive parameters is perturbed so as to reproduce the observed fault slip. Hence, the principal features of the coseismic slip pattern are explained by a stress-driven fault model in which: (1) a spatially unresolved asperity is found equivalent to a stress drop of 18 MPa averaged over an area of 15 sq km, and (2) driving stress is essentially absent on the fault segment overlapping the 1940 earthquake rupture zone.

Description: The present conference on electrochemical power sources encompasses systems of such types as the thermoelectric, advanced rechargeable, lithium reserve, rechargeable, and nonrechargeable, nickel-cadmium and nickel-hydrogen rechargeable, lead-acid, nickel-zinc and nickel-iron rechargeable, nickel-cadmium and nickel-hydrogen rechargeable, and fuel cells. Attention is given to Si-Ge alloy multicouple technology, sodium-sulfur battery development status, the safety aspects of a rechargeable lithium C cell, fiber-structure electrodes for nickel-cadmium batteries, energy density improvements in Li/carbon monofluoride cells, zinc-air button cell technology, catalyzed cathodes for Li/SOCl2 cells, the effect of polymer structure on the rate capability of the lithium-iodine cell, and a methanol fuel cell powerplant.

Description: Atmospheric interactions involving the nitrogen species are varied and complex. These interactions include photochemical reactions, initiated by the absorption of solar photons and chemical kinetic reactions, which involve both homogeneous (gas-to-gas reactions) and heterogeneous (gas-to-particle) reactions. Another important atmospheric interaction is the production of nitrogen oxides by atmospheric lightning. The nitrogen cycle strongly couples the biosphere and atmosphere. Many nitrogen species are produced by biogenic processes. Once in the atmosphere nitrogen oxides are photochemically and chemically transformed to nitrates, which are returned to the biosphere via precipitation, dry deposition and aerosols to close the biosphere-atmosphere nitrogen cycle. The sources, sinks and photochemistry/chemistry of the nitrogen species; atmospheric nitrogen species; souces and sinks of nitrous oxide; sources; sinks and photochemistry/chemistry of ammonia; seasonal variation of the vertical distribution of ammonia in the troposphere; surface and atmospheric sources of the nitrogen species, and seasonal variation of ground level ammonia are summarized.

Description: If all biotic sinks of atmospheric CO2 reported were added a value of about 0.4 Gt C/yr would be found. For each category, a very high (non-conservative) estimate was used. This still does not provide a sufficient basis for achieving a balance between the sources and sinks of atmospheric CO2. The bulk of the discrepancy lies in a combination of errors in the major terms, the greatest being in a combination of errors in the major terms, the greatest being in the net biotic release and ocean uptake segments, but smaller errors or biases may exist in calculations of the rate of atmospheric CO2 increase and total fossil fuel use as well. The reason why biotic sinks are not capable of balancing the CO2 increase via nutrient-matching in the short-term is apparent from a comparison of the stoichiometry of the sources and sinks. The burning of fossil fuels and forest biomass releases much more CO2-carbon than is sequestered as organic carbon.

Description: The initial attempts to model the atmospheric CO2 distribution, including couplings to the ocean and biosphere as sources and sinks of atmospheric CO2, encourage the notion that this approach will lead to useful quantitative constraints on CO2 fluxes. Realization of this objective will require: (1) continued improvement in the realism of the global transport modeling; (2) extended timeline of atmospheric CO2 monitoring, which improved precision and improved definition of the uncertainties in the measured CO2 amounts; and (3) given an accurate knowledge of model capabilities and limitations and given a good understanding of CO2 observations and their limitations, there is a need for good ideas concerning what quantitative information on the carbon cycle can be inferred from global modeling.

Description: A science that chooses the globe as it fundamental biogeophysical unit forces extraordinary conceptual difficulties. The roles of energy flow, matter cycles, carbon cycle, air pollution, global effects, air water interactions are discussed.

Description: Measurements of atmospheric aerosol backscatter coefficients, using a coherent CO2 lidar at 9.25- and 10.6-micron wavelengths, are described. Vertical profiles of the volume backscatter coefficient beta have been measured to a 10-km altitude over the Pasadena, CA, region. These measurements indicate a wide range of variability in beta both in and above the local boundary layer. Certain profiles also indicate a significant enhancement in beta at the 9.25-micron wavelength compared with beta at the 10.6-micron wavelength, which possibly indicates a major contribution to the volume backscatter from ammonium sulfate aerosol particles.

Description: While in the lobes of the distant magnetotail, ISEE-3 encountered regions of compressed magnetic field at a rate of several per day. The duration of these events was 5 to 20 minutes and they were observed 10 to 30 minutes following the onset of substorm activity near the earth. During each event, the lobe magnetic field tilted first northward and then southward with the inflection point near the time of peak field strength. Following the compression events, the lobe field weakened and retained a southward component for 20 to 40 minutes. It is suggested that these traveling compression regions are the lobe signatures of plasmoids moving rapidly down the tail in the plasma sheet. Comparison of ISEE-3 compression event times with substorm onset times yielded propagation speeds of 350 to 750 km/s.

Description: Ionospheric rocket sounding data for eight nighttime auroral events are used to characterize relativistic electron showers and their effects on atmospheric ozone. The rockets were launched from the Poker Flat Research Range in Alaska and from Andoya, Norway over the period 1976-82. Energetic fluxes were always detected but were of insufficient magnitude to produce significant changes in stratospheric ozone. However, middle atmospheric energy sources were found to be dominated by relativistic electrons and X-ray bremmstrahlung, the latter from 40-55 km and the former from 55-60 km altitudes. The ionizing radiation is concluded to be a significant factor in mesospheric ion conductivity, mobility, electric field structure and analytical models for the ion-neutral chemistry.

Description: The dynamics of the polar thermosphere are examined by using observations made from the Dynamics Explorer 2 satellite. The results used in this study were obtained primarily from the Fabry-Perot interferometer (FPI) and the wind and temperature spectrometer (WATS) during the time period from September 1981 through January 1982. Two primary geophysical conditions were examined: these were the southern summer and the northern winter polar regions. The results support the conclusion that above 60 degrees of latitude the neutral winds are strongly controlled by ion/neutral frictional momentum transfer resulting from magnetospheric convection. This implies that the natural coordinate system within which to display the neutral winds in the high polar thermosphere is magnetic. The collected observations of this study were used to assess the validity of two of the large thermospheric general circulation models. The result of this assessment was that the models reasonably represent the vector winds at high altitudes but do not, at present, accurately simulate the thermodynamics of that regime.

Description: A feasibility study has been conducted for a NASA Kennedy Space Center liquid hydrogen/liquid oxygen production facility using solar cell arrays as the power source for electrolysis. The 100 MW output of the facility would be split into 67.6 and 32 MW portions for electrolysis and liquefaction, respectively. The solar cell array would cover 1.65 sq miles, and would be made up of 249 modular 400-kW arrays. Hydrogen and oxygen are generated at either dispersed or centralized water electrolyzers. The yearly hydrogen output is projected to be 5.76 million lbs, with 8 times that much oxygen; these fuel volumes can support approximately 18 Space Shuttle launches/year.

Description: An investigation has been conducted in order to compile quantitative data on the reflective properties of metallic indium. The fabricated samples were of sufficiently high quality that differences from similar second-surface silvered mirrors were not apparent to the human eye. Three second-surface mirror samples were prepared by means of vacuum deposition techniques, yielding indium thicknesses of approximately 1000 A. Both hemispherical and specular measurements were made. It is concluded that metallic indium possesses a sufficiently high specular reflectance to be potentially useful in many solar energy applications.

Description: Lithium-counterdoped n(+)p silicon solar cells are found to exhibit significantly increased radiation resistance to 1-MeV electron irradiation when compared to boron-doped n(+)p silicon solar cells. In addition to improved radiation resistance, considerable damage recovery by annealing is observed in the counterdoped cells at T less than or equal to 100 C. Deep level transient spectroscopy measurements are used to identify the defect whose removal results in the low-temperature aneal. It is suggested that the increased radiation resistance of the counterdoped cells is primarily due to interaction of the lithium with interstitial oxygen.

Description: Line strengths of N2O and its isotopic derivatives in the 1120-1440/cm region were measured at low pressure and high resolution (0.0054/cm). The band strength, rotationless dipole moment matrix elements, and F factor coefficients were considered. First-order nondegenerate perturbation theory was employed to derive explicit expressions for the rotationless dipole moment matrix elements and F factor coefficients. This made it possible to obtain general expressions for the F factor. The derived expressions were also applicable to CO2 bands.

Description: The atmospheric and oceanic mass transport associated with the southern oscillation/El Nino will inevitably induce an interannual variation in the length of day. An empirical correlation study is conducted by comparing the Southern Oscillation Index time series and the interannual length-of-day variation (obtained by removing the long-period and short-period variations from a BIH length-of-day series) for the period 1957-1983. The two series have an encouraging qualitative correlation, in particular with respect to El Nino events; and the linear correlation coefficient is found to be 0.55. It is believed that much, if not most, interannual length-of-day variation is caused by the southern oscillation, and the true correlation is considerably higher than its apparent value considering the fact that the Southern Oscillation Index is merely an indicator derived from two local atmospheric measurements.

Description: Infrared solar absorption spectra recorded at 0.02-per cm resolution during a balloon flight from Alamogordo, NM (33 deg N), on March 23, 1981, have been analyzed for the possible presence of absorption by formic acid (HCOOH). An absorption feature at 1105 per cm has been tentatively identified in upper tropospheric spectra as due to the nu-6 band Q branch. A preliminary analysis indicates a concentration of about 0.6 ppbv and 0.4 ppbv near 8 and 10 km, respectively.

Description: The UV spectrometer polarimeter on the Solar Maximum Mission has been utilized to measure mesospheric O3 altitude profiles by the technique of solar occultation. Sunset data are presented for 1980, during the fall equinoctal period within + or - 20 deg of the geographic equator. Mean O3 concentrations are (40, 16, 5.5, and 1.5) x 10 to the 9th/cu cm at 50, 55, 60, and 65 km, respectively. Some profiles exhibit altitude structure which is wavelike. The mean O3 profile is fit best with the results of a time-dependent model if the assumed water-vapor mixing ratio employed varies from 6 ppm at 65 km.

Description: A comprehensive formula is worked out for the photochemical time constant of minor constituents in the middle atmosphere. The formula is particularly useful for evaluating the time constants for families of some chemical species that are strongly coupled by rapid exchange reactions. Height profiles of photochemical time constants are calculated for individual species and their families based on the chemical reaction rate constants recommended in the recent WMO and JPL reports. Potential exchange reactions among various family members are discussed, and the effects of the choice of family membership on the time constant are evaluated.

Description: Sixty-four observations of the orbital node made by the Lageos satellite over a five year time interval reveal an acceleration of (-8.1 + or - 1.8) x 10 to the -8 power arcseconds day/2 due to a source which is not presently modeled in the GEODYN orbit determination computer program. This acceleration cannot be explained by the ocean tide with 18.6 year period, assuming it to be an equilibrium tide. Instead it seems to be due to postglacial rebound, which changes the J(2) coefficient in the spherical harmonic expansion of the earth's gravitational field at the rate of (-8.2 + or - 18) x 10 to the -19th power/s; this in turn accelerates the node. This rate does not agree with the -32 x 10 to the -19th power/s predicted by Wu and Peltier's (1982) L2 model, which has upper and lower mantle effective viscosities of 10 to the 21st and 22nd powers Pa's, respectively. It does agree well with their L1 model, which gives about 10 x 10 to the 19th power/s. Since the effective viscosity is 10 to the 21st power Pa s throughout the entire mantle in the L1 model, the results support the contentions that the efective viscosity is near 10 to the 21st power Pa s everyhere in the mantle, and this relatively low value for the effective viscosity may have permitted several degrees of polar wander due to glaciation during the Quaternary Ice Age. Previously announced in STAR as N84-13705

Description: ISEE-3 magnetic-field measurements in the region of the geomagnetic tail from -80 to -220 earth radii are reported and discussed. A well-ordered field structure is found, comprising two 7-8-nT lobes separated by a plasma sheet, an embedded neutral sheet with significant By fields, and an intermittent plasma-sheet boundary layer with 5-nT-amplitude (peak-to-peak) electromagnetic waves. The plasma-sheet Bz distribution changes from principally northern orientation near the earth to an approximately equal north-south distribution at 200-220 earth radii. These findings are considered to be in general agreement with magnetic-reconnection models of the magnetosphere, with reconnection either throughout the region observed (in tearing-mode or plasmoid-formation models) or at a constant (about 220-earth-radii) or variable (40-80 to 220-earth-radii) X line (in X-line models).

Description: Using plasma electron and magnetic field measurements from ISEE 3, 220 earth radii from earth, it is found that the magnetotail at that distance is a coherent structure that evidently waves about through distances comparable to its own lateral scale size. For about one-third of the time it was inside the magnetotail, ISEE 3 was in the plasma sheet. During quiet times the plasma sheet is apparently quite thin, but in response to geomagnetic activity it expands, becoming filled with hot plasma flowing tailward at speeds sometimes exceeding 1000 km/sec, and forces the magnetotail cross-section itself to expand. The plasma sheet's expansion is delayed typically by about 30 minutes from the onset of the associated geomagnetic activity (often a clearly identified isolated substorm). The magnetic field in the newly-expanded plasma sheet usually exhibits a few-minute steep northward excursion followed by a more prolonged (and often steep) southward excursion. These are believed to be the signatures of arrival of a plasmoid formed and released near the earth at the onset of the corresponding geomagnetic activity. The discreteness of these plasma releases through the magnetotail and their close association with onsets of geomagnetic activity at earth suggest that they are consequences of spontaneous release, probably by magnetic reconnection, of energy and plasma earlier stored in the magnetotail.

Description: The effects of solar activity on stratospheric ozone were studied between 1970 and 1976 by the NIMBUS 4 backscattered ultraviolet experiment. Results show that, after correcting for instrument sensitivity, globally averaged ozone decreased by 3-4 percent above 2 mbar to less than 1 percent at 10 mbar, as solar activity decreased from solar maximum to solar minimum. This systematic ozone decrease (at all pressure levels) and the seemingly periodic oscillation (generally a 2 year period) seem to be associated with conventional indices of solar activity, which suggests a solar UV-ozone relationship. However, since the ozone depletion, especially at 40 km, is characteristic of atmospheric fluorocarbon injection effects, the solar cycle ozone relationship should be qualified: it may exist if the solar UV flux varies by 15-20 percent in the shorter-wavelength region (less than 200 nm).

Description: The Cold Arctic Mesopause Program (CAMP) was conducted at ESRANGE, Sweden, in July/August 1982. During the time period of several weeks, the temperature was monitored by ground-based OH emission spectrometers and by satellite radiance measurements. Rocket launchings occurred on the nights of 3/4 and 11/12 August. On 3/4 August, seven rocket payloads were launched during a period of noctilucent cloud sighting over ESRANGE. The presence of the NLC was confirmed by several rocket-borne photometer profiles. The temperature measurements showed that the temperature profiles in the stratosphere and lower mesosphere were near the expected values of high latitude summer models. A large amplitude wave structure with three temperature minima of 139K, 114K and 111K were observed at altitudes between 83 and 94 km. The temperature minimum at 83 km was the location of the observed NLC. The temperature minima caused by the growth of the gravity wave amplitude in the highly stable mesosphere provide the regions for the growth of particles by nucleation to optical scattering size, as well as regions where the nuclei for condensation can be formed through ion chemistry paths.

Description: Ocean floor basalts studied from the Galapagos Ridge, FAMOUS area, Cayman Trough and Kilauea east rift contain 20-200 ppm carbon and 0.3-2.8 ppn nitrogen as sums of the vesicle-filling gases CO2 and N2 and dissolved species. The wide range of carbon contents found is due partly to the different extent of outgassing of vesicle-filling gases and partly to depth dependency of dissolved CO2 in the basalts. Sulfate commonly exists with sulfide in these basalts, and the sulfate/sulfide ratio increases with increasing water content, perhaps reflecting the higher oxidation potential in basalt melt of the higher water content.

Description: ISEE-3 measurements indicate that a broad mantle-like boundary layer plasma often exists within the distant geomagnetic tail lobes at all latitudes, directly adjacent to the tail magnetopause. The presence of this boundary layer at large tail distances indicates that plasma from the magnetosheath often crosses the magnetopause locally along much of the length of the tail, and is evidence that the tail is 'open'.

Description: Line parameters for the nu(5) and 2nu(9) bands and associated hot bands of HNO3 have been calculated and compared with laboratory spectra, and the results are presented. Spectral intervals near 870/cm for which best agreement was obtained are used to quantitatively analyze HNO3 absorption features in 0.02/cm resolution stratospheric solar absorption spectra.

Description: Ozone data were obtained in the free troposphere at altitudes of 5 to 7.5 km and at latitudes from 44 degrees N to 46 degrees S during a 3-week period from October 19 to November 4, 1982. Flight trajectories included the continental U.S., Central America, and the western coast of South America. Maximum observed ozone was 110 ppb at about 41 degrees S latitude and at an altitude of 7.3 km (msl). Analysis of the data as a function of latitude showed a region of elevated ozone in the southern latitudes extending from about 2 degrees to 30 degrees in which latitudinal ozone averages (2 degree bands) peaked at about 80 ppb. Ozone concentrations, measured at northern latitudes, were lower, averaging about 35 ppb. A discussion of the data, including comparison with other ozone data sets, is presented.

Description: Total vertical column amounts of NO have been derived from infrared solar absorption spectra recorded near sunrise and sunset with the 0.01 per cm resolution Fourier transform interferometer at the national Solar Observatory on Kitt peak (elevation 2095 m, latitude 31.9 degrees N) on February 23, 1981. The results show an increase in NO concentration in the morning, late afternoon values about 40 percent higher than in the morning, and a decrease in NO concentration prior to sunset. The measured diurnal changes in the total vertical column amount are compared with values obtained from time-dependent photochemical calculations.

Description: Measurements of SO2 emission rates and concentrations and of particle distribution, size, shape, and composition were made in quiescent volcanic plumes emitted into the troposphere from Poas and Arenal volcanos, Costa Rica, and Colima volcano, Mexico. SO2 emission rates were 700 + or - 180 metric tons per day (t/d) for Poas, 210 + or - 30 t/d for Arenal, and 320 + or - 50 t/d for Colima. The concentrations of SO2 calculated from the COSPEC/lidar data were 5-380 ppb. Concentrations of SO2 measured directly by flame photometry were 10-250 ppb. Particles collected in the plumes with a quartz crystal microbalance impactor were mostly less than 3 microns in diameter and consisted of droplets of dilute sulfur-bearing solutions and minor amounts of layer silicate particles coated with a sulfur-bearing film or crust. Total particle concentrations were 4.7 micrograms per cu.m for Poas and 18.8 micrograms per cu.m for Colima. Comparison of concentrations of SO2 in the plumes with gas samples collected at fumaroles on the ground suggests that the plumes are diluted by the atmosphere by factors of up to 100,000.

Description: A two-dimensional photochemical model based on diabatic circulation has been used to simulate the behavior of N2O, CFCl3(F-11) and CF2Cl2(F-12) The circulation is based on estimates of net heating from the ground to 60 km. Eddy diffusion has been reduced with respect to other model studies with Kzz = 2000 sq cm/s everywhere bove 100 mbar. Resulting tracer profiles show reasonable agreement with measured profiles in the tropics and fall off much more sharply with altitude than those produced by models using larger values of Kzz. The agreement obtained is at least as good as that obtained with adjustable, eddy diffusion parameters. The diabatic circulation treatment is more closely related to related to real physical processes and thus more easily interpreted. Diffusive mixing appears to be more important in determining the details of the tracer distributions than the basic morphology.

Description: The mid-latitude upper stratospheric ozone profiles obtained by the solar backscatter ultraviolet instrument on the Nimbus 7 satellite show a clear annual cycle both in the absolute ozone amounts between 0.98 and 15.6 mbar and in the magnitude of disturbances that reveal themselves as longitudinal structure. At the lowest pressure analyzed a winter maximum in ozone exists, but as one progresses downward in altitude a shift in the temporal phase of the annual cycle occurs in the vicinity of 3 to 4 mbar. Comparison of the observed behavior with the predictions of a one-dimensional photochemical model shows a systematic tendency for calculated ozone amount to be 20-27 percent below the data for pressures less than 7.8 mbar. The chemical model successfully predicts the change in phase of the annual cycle, although at a pressure greater than observed. Diagnosis of model results shows the observed shift to be closely coupled to the magnitude of the ozone column density near 3-4 mbar. The wavelength-dependent attenuation of the solar radiation field by ozone alters the relative magnitude of the molecular oxygen and ozone dissociation rates, leading to a change in the temporal phase of the annual cycle.

Description: One-dimensional radiative and photochemical models are used to determine how much CO2 must have been present to maintain a temperate early climate and to examine the consequences that are implied for the controls on atmospheric oxidation state. It is shown that CO2 concentrations of the order of 1000 PAL are required to keep the average surface temperature close to the present value, if albedo changes and heating by reduced greenhouse gases were relatively unimportant. The oxidation state of such a high-CO2, prebiotic atmosphere should have been largely determined by the balance between the H2O2 rainout rate and the rate at which hydrogen escaped to space, with only a weak dependence on the volcanic outgassing rate or on other speculative sources of H2. The implied upper limit on the ground-level O2 mixing ratio is approximately 10 to the -11th and is subject to less uncertainty than the results of previous models.

Description: A time-dependent, one-dimensional photochemical model of the troposphere is used to describe the vertical distribution of atmospheric trace constituents for summer-time conditions at midlatitudes in the Northern Hemisphere. The model incorporates a planetary boundary layer (PBL) parametrization and a detailed chemical mechanism that includes the photochemistry of important nonmethane hydrocarbon species formed during the oxidation process. One result of the parametrized PBL is that the concentrations of some trace species in the free troposphere are 20-30 percent higher than when mixing processes are described by a vertical eddy diffusion coefficient which is held constant with respect to height and time. The lifetime of the oxides of nitrogen against photochemical conversion to nitric acid during summertime conditions is on the order of six hours. This lifetime is short enough to deplete most of the NO(x) in the PBL so that other reactive nitrogen species are more abundant than NO(x) throughout the free troposphere.

Description: A petrologic model of the northern Mississippi Embayment, derived from gravity, seismic and rift data, is evaluated by converting the model to a magnetization model which is compared with satellite magnetic anomaly models. A magnetization contrast of approximately -0.54 A/m, determined from the petrologic model of the embayment compares favorably to values of -0.62 A/m and -0.45 A/m from a Magsat United States Apparent Magnetization Contrast Map and a published POGO magnetization contrast model, respectively. The petrologic model suggests that the magnetic anomaly low associated with the Mississippi Embayment may be largely due to the intrusion under non-oxidizing conditions of low Curie temperature gabbroic material at the base of the crust of the embayment. Near-surface mafic plutons, bordering the Mississippi Valley Graben, appear from aeromagnetic data to have higher magnetizations than the deeper gabbroic material; however, it is impossible to ascertain if this is due to compositional differences or similar material at shallower (lower temperature) depths. These results indicate that variations in the Curie temperatures of intrusions accompanying rifting may account for a large part of the wide range of magnetic anomalies associated with presently inactive rifts with normal heat flow.

Description: A discussion is presented concerning the role of water in its liquid and gaseous states in the chemistry and photochemistry of the earth's troposphere, with attention to the formation of the hydroxyl radical, oxidation chains involving the gases methane, carbon monoxide and ammonia, the atmospheric chemistry of the sulfur, hydrogen, halogen and nitrogen species, and the function of lightning as a source of tropospheric species. The phenomena of 'rainout', 'washout', and the aqueous chemistry of cloud an rain droplets and of water-covered aerosols, are noted. A section is devoted to the past and anticipated impact of anthropogenic activities on the chemistry and composition of the earth's atmosphere.

Description: Using the 9 layer general circulation model developed at the Goddard Laboratory for Atmospheric Sciences (GLAS), several 4 to 5 day integrations were made to assess the impact that latent heating processes (supersaturation and moist convective) have on the model forecasts. In an earlier study by Shukla (1981) it was hypothesized that because of strong interaction between dynamics and moist convection, small initial errors grow very fast and make short range forecasting difficult. The purpose of this study was to examine if prescribed heating rates can improve the forecasts for a few days.

Description: The structure of the stratospheric spectrum, measured with a resolution of 0.0033/cm unapodized in the 7-90/cm spectral interval is described. The spectra from measurements recorded on April 24, 1979 from a balloon-borne platform at about 39 km altitude launched from the National Scientific Balloon Facility of Palestine, TX are presented. The main spectroscopic constituents include a few strong and saturated lines due to the rotational spectrum of water vapor, to magnetic dipole transitions of oxygen, and to the rotational spectrum of ozone. It is shown that the lines of ozone prevent the positive identification of the contribution to the submillimeter spectrum of several minor constituents such as HF, HCl, HCN, HNO3, and N2O. The assignments which are possible in the spectra are revised.

Description: Infrared solar spectra have been obtained during a series of flights with a balloon borne Fourier Transform Spectrometer system. Major emphasis during these flights was placed on obtaining data during sunset. The spectra thus contain information on the atmospheric transmission over long stratospheric paths. These spectra have been analyzed to obtain information on the constituents responsible for the observed absorptions and the distribution with altitude of several of these constituents of interest in stratospheric chemistry. These spectra have also been used to determine the spectroscopic parameters for several compounds such as O3 which are difficult to study in the laboratory. A description of the instrumentation used to obtain the data, samples of the spectra obtained, and details of the analysis are given.

Description: The high-temperature thermoelectric energy-conversion theory is examined. It is shown that semiconductors are the logical choices for high-figure of merit-value materials, but the requirements for optimization differ depending on whether the material is classed as a broad-band or narrow-band semiconductor. Optimization is discussed as a function of temperature. Phonon scattering mechanisms are considered; and for the reduction of thermal conductivity, basic material guidelines are given. Although experimental results indicate that ZT (where Z is the figure of merit and T is the temperature) of about 1 represents an upper limit, there is in fact, no theoretical limitation. It is unlikely that the Z values will be significantly reduced by radiation transfer at temperatures lower than 2000 K. The current status of materials research is also considered. The rare-earth chalcogenides which behave as n-type semi-conductors and the boron-rich borides which exhibit hopping p-type conductivity behavior are the materials that show promise for high-temperature Z values. The reasons for low thermal conductivities in these materials is discussed.

Description: Recent theoretical and observational studies of middle atmosphere electrodynamics are reviewed. Attention is given to observations of large electric fields in the mesosphere and stratosphere which suggest magnitudes of about one volt per sq m. Recommendations are offered with respect to areas of future study, with emphasis on studies of the morphology of large electric fields, and their relationship with external influences such as magnetospheric electric fields and tropospheric thunderstorms.

Description: If a malfunction occurs in a solar thermal point-focus distributed receiver power plant while a concentrator is pointed at the sun, motion of the concentrator may stop. As the sun moves relative to the earth, the spot of concentrated sunlight then slowly walks off the receiver aperture, across the receiver face plate, and perhaps across adjacent portions of the concentrator. Intense local heating by the concentrated sunlight may damage or destroy these parts. The behavior of various materials under conditions simulating walk-off of a parabolic dish solar collector were evaluated. Each test consisted of exposure to concentrated sunlight at a peak flux density of about 7000 kW/square meter for 15 minutes. Types of materials tested included graphite, silicon carbide, silica, various silicates, alumina, zirconia, aluminum, copper, steel, and polytetrafluoroethylene. The only material that neither cracked nor melted was grade G-90 graphite. Grade CS graphite, a lower cost commercial grade, cracked half-way across, but did not fall apart. Both of these grades are medium-grain extruded graphites. A graphite cloth (graphitized polyacrylonitrile) showed fair performance when tested as a single thin ply; it might be useful as a multi-ply assembly. High purity slipcast silica showed some promise also.

Description: The steady state gravity wave model of Schoeberl et al. (1983) is extended to compute wave breaking by disturbances originating at the earth's surface. For winter and summer mean zonal wind profiles, no waves reach the mesosphere unless the absolute value of the zonally averaged perturbed zonal velocity minus c is greater than approximately 20 m/sec. Gravity waves with c = 0 can only reach the winter mesosphere if planetary scale waves are present in the troposphere and the lower stratosphere, to provide strong zonal wind channels for upward wave propagation. This results in nonzonal wave breaking in the mesosphere which could provide in situ forcing of planetary waves. Dissipation of gravity waves by molecular viscosity and conduction can provide significant deceleration and heating/cooling in the 85-105 km region.

Description: The three-satellite ERBE will be flown in the mid-1980s and will provide upgraded data on changes in the input and outflow of energy which drives climatic phenomena. The spacecraft will carry radiometers, self-calibration equipment, and be programmed with inversion and averaging algorithms. Radiation will be scanned at 0.2-5 and 5-50 microns. The ACRIM detector, similar to that on the SMM spacecraft, will measure the incoming solar radiation at the 600 km sun-synchronous orbit travelled by the three ERBE spacecraft. Data transmitted to the NASA-Langley Center will be analyzed with algorithms which extract radiant flux data from the measured radiances.

Description: Results from an intercomparison of methods to measure carbon monoxide (CO), nitric oxide (NO), and the hydroxyl radical (OH) are discussed. The intercomparison was conducted at Wallops Island, Virginia, in July 1983 and included a laser differential absorption and three grab sample/gas chromatograph methods for CO, a laser-induced fluorescence (LIF) and two chemiluminescence methods for NO, and two LIF methods and a radiocarbon tracer method for OH. The intercomparison was conducted as a field measurement program involving ambient measurements of CO (150-300 ppbv) and NO (10-180 pptv) from a common manifold with controlled injection of CO in incremental steps from 20 to 500 ppbv and NO in steps from 10 to 220 pptv. Only ambient measurements of OH were made. The agreement between the techniques was on the order of 14 percent for CO and 17 percent for NO. Hardware difficulties during the OH tests resulted in a data base with insufficient data and uncertanties too large to permit a meaningful intercomposition.

Description: The ozone density of the earth's mesosphere in the 1.0-0.1 mbar (48 to 70 km) region has been measured at sunlit latitudes for the period from December 1981 until the present by an ultraviolet spectrometer on the Solar Mesosphere Explorer satellite. Results for 1982 are reported. The ozone mixing ratios are found to be highly variable in time and place, with maxima occurring in the winter hemispheres. The results show complex time variations at all pressure levels, with annual and semiannual variations apparent at most pressures and latitudes. A relative maximum occurs in July at the equator.

Description: In this study it is shown that the upward moving electron beams observed by DE-1 in the dayside polar cusp at 2 to 5 R sub E drive an electrostatic electron acoustic mode, rather than the whistler mode near resonance, as previously concluded. The characteristics of this instability are compared with the properties of hiss in the polar cusp observed by the Dynamics Explorer (DE-1) satellite. The hiss frequencies and funnel shaped frequency-time spectra are consistent with the electron acoustic mode. However, because the hiss often has a fluctuating magnetic field component near the axis of the funnel shape, the hiss is probably composed of both electron acoustic and whistler mode waves.

Description: The stratospheric emission in the submillimeter spectral region has been measured from 38.2 km altitude with a resolution of 0.0033 kayser. In most cases this resolution makes possible the separation of contributions caused by the individual rotational transitions. An atlas of the observed features is given as a guide to both the measurements of minor stratospheric constituents concentration and the evaluation of stratospheric transparency for the measurement of nontelluric sources.

Description: A transfer function approach is taken in constructing a spectral model of the acoustic-gravity wave response in a multiconstituent thermosphere. The model is then applied to describing the thermospheric response to various sources around the globe. Zonal spherical harmonics serve to model the horizontal variations in propagating waves which, when integrated with respect to height, generate a transfer function for a vertical source distribution in the thermosphere. Four wave components are characterized as resonance phenomena and are associated with magnetic activity and ionospheric disturbances. The waves are either trapped or propagate, the latter becoming significant when possessing frequencies above 3 cycles/day. The energy input is distributed by thermospheric winds. The disturbances decay slowly, mainly due to heat conduction and diffusion. Gravity waves appear abruptly and are connected to a sudden switching on or off of a source. Turn off of a source coincides with a reversal of the local atmospheric circulation.