ALBERT

Description: The Cenozoic volcanic activity on Iceland has been recorded in North Atlantic sediments drilled during several Ocean Drilling Program (ODP)/Deep Sea Drilling Project legs (Legs 104, 151, 152, 162, and 163). Leg 162 (North Atlantic-Arctic Gateways II) recovered ash layers at Sites 982, 985, and 907 (Jansen, Raymo, Blum, et al., 1996, doi:10.2973/odp.proc.ir.162.1996). The revisited Site 907 was first drilled during Leg 151, and the ash from this site has been described in detail by Lacasse et al. (1996, doi:10.2973/odp.proc.sr.151.122.1996) and Werner et al. (1996, doi:10.2973/odp.proc.sr.151.123.1996). Site 982 is located within the Hatton-Rockall Basin on the Rockall Plateau, which is situated west of the British Isles. Site 985 is located northeast of Iceland at the foot of the eastern slope of the Iceland Plateau, adjacent to the Norwegian Basin. Here we report chemical analyses of Neogene tephra layers from Holes 982A, 983B, 982C, 985A, and 985B. The sedimentary sequence at Site 982 spans the lower Miocene-Holocene; Site 985 recovered sediments spanning the upper Oligocene-Holocene. Twenty-two distinct ash layers and ash-bearing sediments were sampled in Holes 982A-982C (Cores 162-982A-16H through 24H, 162-982B-14H through 56X, and 162-982C-15H through 27H), and 59 ash layers were sampled in Holes 985A and 985B (Cores 162-985A-11H through 59X, and 162-985B-11H through 14H). Almost 50% of the sampled ash is strongly altered (predominantly from Site 985). A cluster of altered thin layers in the lower Pliocene of Site 985 (top of Unit III) is remarkable.

Description: Sediment spectral reflectance measurements were generated aboard the JOIDES Resolution during Ocean Drilling Program Leg 162 shipboard operations. The large size of the raw data set (over 1.3 gigabytes) and limited computer hard disk storage space precluded detailed analysis of the data at sea, although broad band averages were used as aids in developing splices and determining lithologic boundaries. This data report describes the methods used to collect these data and their shipboard and postcruise processing. These initial results provide the basis for further postcruise research.

Description: Rocks of the lower sheeted dike complex of Hole 504B sampled during Leg 140 were analyzed for major and trace element compositions to investigate the effects of igneous processes and hydrothermal alteration on the compositions of the rocks. The rocks are relatively uniform in composition and similar to the shallower dikes. They are moderately evolved mid-ocean-ridge basalts (MORB) with relatively high MgO (7.9-10 wt%) and Mg# (0.60-0.70), and have unusually low incompatible element contents (TiO2 = 0.42-1.1 wt%, Zr = 23-62 ppm). Discrete compositional intervals in the hole reflect varying degrees of differentiation, and olivine and plagioclase accumulation in the rocks, and may be related to injection of packets of dikes having similar compositions. Systematic depletions of total REE, Zr, Y, TiO2, and P2O5 in centimeter-size patches are most likely attributed to exclusion of highly differentiated, late-stage interstitial liquids from small portions of the rocks. The rocks exhibit increased H2O+ reflecting hydrothermal alteration. Replacement of primary plagioclase by albite and oligoclase led to local gains of Na2O, losses of CaO, and slightly positive Eu anomalies. Some mobility of P2O5 led to minor increases and decreases in P2O5 contents, and some local mobility of Ti may have occurred during alteration of titanomagnetite to titanite. Higher temperatures of alteration in the lower sheeted dikes led to breakdown of pyroxene and sulfide minerals and losses of Zn, Cu, and S to hydrothermal fluids. Later addition of anhydrite to the rocks in microfractures and replacing plagioclase caused local increases in sulfur contents. The lower sheeted dikes are a major source of metals to hydrothermal fluids for the formation of metal sulfide deposits on and within the seafloor.

Description: Sixty-three samples representing 379 m of sheeted dikes from Deep Sea Drilling Project/Ocean Drilling Program Site 504B have been analyzed for major and selected trace elements by X-ray fluorescence. The samples range from microcrystalline aphyric basalts to moderately phyric (2%-10% phenocrysts) diabase that are typically multiply saturated with plagioclase, olivine, and clinopyroxene, in order of relative abundance. All analyzed samples are classified as Group D compositions with moderate to slightly elevated compatible elements (MgÆ-value = 0.65% ± 0.03%; Al2O3 = 15.5% ± 0.8%; CaO = 13.0% ± 0.3%; Ni = 114 ± 29 ppm), and unusually depleted levels of moderate to highly incompatible elements (Nb 〈 1 ppm; Zr = 44 ± 7 ppm; Rb 〈 0.5 ppm; Ba ~ 1 ppm; P2O5 = 0.07% ± 0.02%). These compositions are consistent with a multistage melting of a normal ocean ridge basaltic mantle source followed by extensive fractionation of olivine, plagioclase, and clinopyroxene. Leg 140 aphyric to sparsely phyric (0%-2% phenocrysts) basalts and diabases are compositionally indistinguishable from similarly phyric samples at higher levels in the hole. An examination of the entire crustal section, from the overlying volcanics through the sheeted dikes observed in Leg 140, reveals no significant trends indicating the enrichment or depletion of Costa Rica Rift Zone source magmas over time. Similarly, significant trends toward increased or decreased differentiation cannot be identified, although compositional patterns reflecting variable amounts of phenocryst addition are apparent at various depths. Below ? 1700 mbsf to the bottom of the Leg 140 section, there is a broadly systematic pattern of Zn depletion with depth, the result of high-temperature hydrothermal leaching. This zone of depletion is thought to be a significant source of Zn for the hydrothermal fluids depositing metal sulfides at ridge-crest hydrothermal vents and the sulfide-mineralization zone, located in the transition between pillow lavas and sheeted dikes. Localized zones of intense alteration (60%-95% recrystallization) are present on a centimeter to meter scale in many lithologic units. Within these zones, normally immobile elements Ti, Zr, Y, and rare-earth elements are strongly depleted compared with "fresher" samples centimeters away. The extent of compositional variability of these elements tends to obscure primary igneous trends if the highly altered samples are not identified or removed. At levels up to 40% (or possibly 60%) recrystallization, Ti, Zr, and Y retain their primary signatures. Although the mechanisms are unclear, it is possible that these intense alteration zones are a source of Y and rare-earth elements for the typically rare-earth-element-enriched hydrothermal vent fluids of mid-ocean ridges.

Description: Geochemical data from plagioclase-hosted silicate melt inclusions from Leg 140, Hole 504B diabase dikes are reported. Hand-picked plagioclase grains were heated to 1260°-1280°C to remelt the glass inclusions and to infer trapping temperatures. The samples were then polished to expose the inclusions, which were analyzed by electron and ion microprobes. Inclusion compositions are mainly in equilibrium with the host plagioclase and are more depleted in incompatible elements than the host rock. Simple crystal-liquid equilibrium calculations show that the melt inclusions could have been in equilibrium with depleted abyssal peridotite diopsides, whereas whole-rock basalt compositions generally could not have been. The melt inclusions are significantly more depleted than normal (N-type) mid-ocean-ridge basalt (MORB) and are consistent with being produced by 8%-16% incremental or open-system melting with 2% residual porosity in the peridotite source. These magmas were formed during pressure-release melting of the mantle over a range of depths between 30 and 15 km.

Description: Drilling during Legs 137 and 140 of the Ocean Drilling Program deepened Hole 504B, the only hole to penetrate through the volcanic section and into the underlying hydrothermally altered sheeted dike complex, by 438.1 m to a total depth of 2000.4 meters below seafloor. This paper presents the secondary mineralogy, bulk-rock sulfur contents, and stable isotopic (O, S) compositions, plus oxygen isotopic compositions of secondary minerals from the lower sheeted dike complex drilled during Legs 137 and 140. Various evidence indicates higher temperatures of hydrothermal alteration in the lower dikes than in the upper dikes, including: the local presence of secondary clinopyroxene in the lower dikes; secondary anorthite and hornblende in the lower dikes vs. mainly actinolite and albite-oligoclase in the upper dikes; generally increasing Al and Ti contents of amphibole downward in the dike section; and greater 18O depletions of the lower dikes (d18O = 3.6-5.0 per mil) compared with the upper dikes. Early high-temperature alteration stages (T = 350°-500°C) resulted in 18O depletions and losses of metals (Cu, Zn) and sulfur from the rocks. Local incorporation of reduced seawater sulfate led to elevated d34S values of sulfide in the rocks (up to 2.5 per mil). Quartz + epidote formed in crosscutting veins at temperatures of 310°-320°C from more evolved fluids (d18O = 1 per mil). Late-stage lower-temperature (~250°C) reactions producing albite, prehnite, and zeolites in the rocks caused slight 18O enrichments, but these were insufficient to offset the 18O depletions caused by earlier higher-temperature reactions. Addition of anhydrite to the rocks during seawater recharge led to increased S contents of rocks that had previously lost S during axial hydrothermal alteration, and to further increases in d34S values of total S in the rocks (up to 12 per mil). Despite the evidence for seawater recharge to near the base of the sheeted dike complex, the paucity of late zeolites in the lower dikes suggests that late-stage, off-axis circulation was mainly restricted to the volcanics and shallowest dikes, or to localized high-permeability zones (faults) at depth.

Description: Fluid inclusions in variably altered diabase recovered from Ocean Drilling Program Legs 137 and 140 at Hole 504B, Costa Rica Rift, exhibit fluid salinities up to 3.7 times that of seawater values (11.7 wt% NaCl equivalent) and exhibit uncorrected homogenization temperatures of 125°C to 202°C. The liquid-dominated inclusions commonly are entrapped in zones of secondary plagioclase and may be primary in origin. Fluid salinities are similar to compositions of fluids venting on the seafloor (0.4-7.0 wt% NaCl) and overlap with those measured in metabasalt samples recovered from near the Kane Fracture Zone on the Mid-Atlantic Ridge and from the Troodos ophiolite, Cyprus. The salinity variations may reflect hydration reactions involving formation of secondary mineral assemblages under rock-dominated conditions, which modify the ionic strength of hydrothermal fluids by consuming or liberating water and chloride ion. Rare CO2-CH4-bearing inclusions, subjacent to zones where talc after olivine becomes an important secondary mineral phase (1700 mbsf), may have formed due to local interaction of seawater and olivine at low water to rock ratios. Corrected average fluid inclusion homogenization temperatures exhibit a gradient from 159°C at a depth of 1370 mbsf to 183°C at a depth of 1992 mbsf and are in apparent equilibrium with the present conductive downhole temperatures. These data indicate that fluid inclusions may be used to estimate downhole temperatures if logging data are unavailable. The compositional and thermal evolution of the diabase-hosted fluids may reflect late-stage, off-axis circulation and conductive heating of compositionally modified seawater in the sheeted dike complex at Hole 504B.

Description: Dolerites sampled from the lower sheeted dikes from Hole 504B during Ocean Drilling Program Legs 137 and 140, between 1562.4 and 2000.4 mbsf, were examined to document the mineralogy, petrography, and mineral parageneses associated with secondary alteration, to constrain the thermal history and composition of hydrothermal fluids. The main methods used were mineral chemical analyses by electron microprobe, X-ray diffraction, and cathodoluminescence microscopy. Temperatures of alteration were estimated on the basis of single and/or coexisting mineral chemistry. Permeability is important in controlling the type and extent of alteration in the studied dike section. At the meter-scale, intervals of weakly altered dolerites containing fresh olivine are interpreted as having experienced restricted exposure to hydrothermal fluids. At the centimeter- or millimeter-scale, alteration patches and extensively altered halos adjacent to veins reflect the permeability related to intergranular primary porosity and cracks. Most of the sheeted dike alteration in this case resulted from non-focused, pervasive fluid-rock interaction. This study confirms and extends the previous model for hydrothermal alteration at Hole 504B: hydrothermal alteration at the ridge axis followed by seawater recharge and off-axis alteration. The major new discoveries, all related to higher temperatures of alteration, are: (1) the presence of hydrothermal plagioclase (An80-95), (2) the presence of deuteric and/or hydrothermal diopside, and (3) the general increasing proportion of amphiboles, and particularly magnesio-hornblende with depth. We propose that the dolerites at Hole 504B were altered in five stages. Stage 1 occurred at high temperatures (less than 500° to 700°C) and involved late-magmatic formation of Na- and Ti-rich diopside, the hydrothermal formation of Na, Ti-poor diopside and the hydrothermal formation of an assemblage of An-rich plagioclase + hornblende. Stage 2 occurred at lower temperatures (250°-320°C) and is characterized by the appearance of actinolite, chlorite, chlorite-smectite, and/or talc (in low permeability zones) and albite. During Stage 3, quartz and epidote precipitated from evolved hydrothermal fluids at temperatures between 310° and 320°C. Anhydrite appeared during Stage 4 and likely precipitated directly from heated seawater. Stage 5 occurred off-axis at low temperatures (250°C) with laumontite and prehnite from evolved fluids.

Description: Seismic velocities have been measured at confining pressures of 100 MPa and 600 MPa for sheeted dike samples recovered during Ocean Drilling Program Legs 137 and 140. The compressional- and shear-wave velocities show an increase with depth at Hole 504B, which is in sharp contrast to the atmospheric pressure velocity measurements performed as part of the shipboard analyses. Rocks exposed to different types of alteration and fracture patterns show distinct changes in their physical properties. The seismic reflectors observed on the vertical seismic profile (VSP) experiment performed during Leg 111 may have been caused by low velocity zones resulting from alteration. The amount of fracturing and hydrothermal alteration in several zones also may have contributed to the acoustic impedance contrast necessary to produce the E5 reflector. Poisson's ratios calculated from laboratory velocity measurements show several low values at depths ranging from 1600 mbsf to 2000 mbsf, which tends to follow similar trends obtained from previous oceanic refraction experiments. A comparison of physical properties between samples recovered from Hole 504B and ophiolite studies in the Bay of Islands and Oman shows a good correlation with the Bay of Islands but significant differences from the measurements performed in the Oman complex.

Description: Leg 140 of the Ocean Drilling Program deepened Hole 504B to a total depth of 2000.4 m below seafloor (mbsf), making it the deepest hole drilled into ocean crust. Site 504, south of the Costa Rica Rift, is considered the most important in-situ reference section for the structure of shallow ocean crust. We present the results of studies of magnetic mineralogy and magnetic properties of Hole 504B upper crustal rocks recovered during Legs 137 and 140. Results from this sample set are consistent with those discussed in Pariso et al. (this volume) from Legs 111, 137, and 140. Coercivity (Hc) ranges from 5.3 to 27.7 mT (mean 12 mT), coercivity of remanence (HCR) ranges from 13.3 to 50.6 mT (mean 26 mT), and the ratio HCR/HC ranges from 1.6 to 3.19 (mean 2.13). Saturation magnetization (JS) ranges from 0.03 to 5.94 * 10**-6 Am**2, (mean 2.52 * 10**-6 Am**2), saturation remanence (JR) ranges from 0.01 to 0.58 * 10**-6 Am2 (mean 0.37 * 10**-6 Am**2), and the ratio JR/JS ranges from 0.08 to 0.29 (mean 0.16), consistent with pseudo-single-domain behavior. Natural remanent magnetization (NRM) intensity ranges from 0.029 to 7.18 A/m (mean 2.95 A/m), whereas RM10 intensity varies only from 0.006 to 4.8 A/m and has a mean of only 1.02 A/m. Anhysteretic remanent magnetization (ARM) intensity ranges from 0.04 to 6.0 A/m, with a mean of 2.46 A/m, and isothermal remanent magnetization (IRM) intensity ranges from 0.5 to 1683 A/m, with a mean of 430.7 A/m. Volume susceptibility ranges from 0.0003 to 0.043 SI (mean 0.011 SI). In all samples examined, high-temperature oxidation of primary titanomagnetite has produced lamellae or pods of magnetite and ilmenite. Hydrothermal alteration has further altered the minerals in some samples to a mixture of magnetite, ilmenite, titanite, and a high-titanium mineral (either rutile or anatase). Electron microprobe analyses show that magnetite lamellae are enriched in the trivalent oxides Cr2O3, Al2O3, and V2O5, whereas divalent oxides (MnO and MgO) are concentrated in ilmenite lamellae.

Description: The post-middle Miocene evolution of sedimentary patterns in the eastern equatorial Pacific Ocean has been deduced from a compilation and synthesis of CaCO3, opal, and nannofossil assemblage data from 11 sites drilled during Leg 138. Improvements in stratigraphic correlation and time scale development enabled the construction of lithostratigraphic and chronostratigraphic frameworks of exceptional quality. These frameworks, and the high sedimentation rates (often exceeding 4 cm/k.y.) provided a detailed and synoptic paleoceanographic view of a large and highly productive region. The three highlights that emerge are: (1) a middle late Miocene "carbonate crash" (Lyle et al., this volume); (2) a late Miocene-early Pliocene "biogenic bloom"; and (3) an early Pliocene "opal shift". During the carbonate crash, an interval of dissolution extending from -11.2 to 7.5 Ma, CaCO3 accumulation rates declined to near zero over much of the eastern equatorial Pacific, whereas opal accumulation rates remained substantially unchanged. The crash nadir, near 9.5 Ma, was marked by a brief shoaling of the regional carbonate compensation depth by more than 1400 m. The carbonate crash has been correlated over the entire tropical Pacific Ocean, and has been attributed to tectonically-induced changes in abyssal flow through the Panamanian seaway. The biogenic bloom extended from 6.7 to 4.5 Ma, and was characterized by an overall increase in biogenic accumulation and by a steepening of the latitudinal accumulation gradient toward the equator. The bloom has been observed over a large portion of the global ocean and has been linked to increased productivity. The final highlight, is a distinct and permanent shift in the locus of maximum opal mass accumulation rate at 4.4 Ma. This shift was temporally, and perhaps causally, linked to the final closure of the Panamanian seaway. Before 4.4 Ma, opal accumulation was greatest in the eastern equatorial Pacific Basin (near 0°N, 107°W). Since then, the highest opal fluxes in the equatorial Pacific have occurred in the Galapagos region (near 3°S, 92°W).

Description: Pore-water samples from the equatorial sedimentary bulge area show reversals in depth profiles of 87Sr/86Sr ratios at the sediment/basement interface. Results of this work support inferences made from previous pore-water data (from DSDP drilling in the area) that large-scale horizontal advection of seawater has occurred through the basement underlying the thick sedimentary sequence in this region. The area of apparent advection includes the eastern part of the equatorial high-productivity zone and part of the Guatemala Basin. We attempted to find links between the observed near-basement reversals in pore-water chemistry and sedimentary thickness, age, and topography of the area. Most of the sites that show horizontal advection have disturbed basement topography or outcrops within 10 to 20 km, suggesting that the cooling effects of outcrops may extend for at least 20 km horizontally. Heat-flow data from the area were compared to determine whether sites showing near-bottom chemistry reversals were consistent with areas of low conductive heat flow. This was generally true for the area of the sedimentary bulge and Guatemala Basin. Not enough pore-water data from the Nazca Plate were available to establish any reliable systematics. Because the high-productivity area is well-sealed from hydrothermal circulation, the missing heat must be lost by horizontal advective heat transport. From profiles of strontium isotopes and other elements that show departure from seawater values with increasing depth in the sediments, but return to seawater values near the basement, it appears that water flows relatively freely through much of the oceanic crust, even when sealed by considerable sedimentary cover.

Description: In the eastern and central Pacific Ocean the most profound change in Neogene calcium carbonate deposition occurred at the late/middle Miocene boundary (about 10 Ma), when carbonate mass accumulation rates (MARs) abruptly dropped. East of the East Pacific Rise (EPR), carbonate deposition essentially ceased. The carbonate compensation depth (CCD) in the Guatemala Basin, for example, rose by 800 m in less than 0.5 Ma. Even the rise crests suffered carbonate losses - Site 846, at the time less than 300 meters deeper than the EPR axis, experienced intervals between 10 and 9 Ma where no carbonate at all was buried. By about 8 Ma carbonate deposition resumed and was concentrated along an equatorial band, suggestive of high surface water carbonate production. East of the EPR, however, CCDs remained shallow since 10 Ma. This event which we have termed the late Miocene carbonate crash marks a fundamental paleoceanographic change that occurred in the eastern Pacific Ocean. Here, we document the changing pattern of carbonate deposition from 13 Ma to 5 Ma by using maps of carbonate MAR reconstructed from ODP Leg 138 and DSDP data. Comparisons to modern oceanographic conditions demonstrate that the late Miocene carbonate crash could not have been caused by an abrupt increase in productivity at 10 Ma or by loss of Corg from continental shelves. Instead it was probably caused by a relatively small reduction in deep-water exchange between the Atlantic and Pacific Oceans through the Panama Gateway prior to the emergence of the isthmus. A small restriction of deep-water exchange through this gateway is sufficient to radically change carbonate MARs in the eastern Pacific.

Description: Ocean Drilling Program (ODP) Leg 138 recovered more than 5500 m of Quaternary to middle Miocene (~17 Ma) sediments from 11 sites in the eastern equatorial Pacific Ocean. These sediments represent the most complete stratigraphic sequence recovered since the start of scientific ocean drilling by the Deep Sea Drilling Project (DSDP) and ODP. The diatoms observed generally are common to abundant and well-preserved throughout the samples examined. The assemblages are characterized by species typical of low-latitudes and regions of high surface-water productivity and are dominated by Thalassiothrix longissima, Thalassionema nitzschioides, Azpeitia nodulifer, and numerous species of Thalassiosira and Nitzschia. Fifty-six biostratigraphic events were identified at Sites 844 through 852, allowing us, in part, to use the diatom zonation of Barron (1985a). This zonation was modified by replacing the Rhizosolenia preabergonii Zone and the upper portion of the Nitzschia jouseae Zone, as used by Barron (1985a), with the Nitzschia marina and Nitzschia jouseae zones, as used by Baldauf (1984, 1987). Twenty-nine biostratigraphic events have been correlated to the Leg 138 paleomagnetic stratigraphy of Schneider (this volume). Nineteen of these events are well constrained to permit recalibration. Diatoms were rare or absent in samples examined from Sites 853 and 854. As such, these sites are not included in the following discussion.

Description: The aims of this study are twofold. First, the study tries to provide the most reliable chronology possible for two critical sections by correlating the magnetic polarity stratigraphy measured in these sediments with a newly revised geomagnetic polarity time scale. Second, this study attempts to examine in detail the nature of seven short events not included in the shipboard standard time scale, but for which abundant magnetostratigraphic evidence was obtained during the Leg. Data presented here force some modifications of the shipboard interpretations of the magnetostratigraphy of Sites 845 and 844 on the basis of new data generated using discrete samples and from a greater appreciation of the magnetostratigraphic signature of Miocene-age short events. Those short events can be classified into two groups: those that probably reflect short, full-polarity intervals and those that more likely represent an interval of diminished geomagnetic intensity. Three of the seven events documented here correspond well with three subtle features, as seen in marine magnetic profiles, that have been newly included in the geomagnetic polarity time scale as short, full-polarity chrons. One of the seven events corresponds to a poorly defined feature of the marine magnetic record that has also been newly included in the geomagnetic polarity time scale, but which was considered of enigmatic origin. The three remaining events investigated here, although they have not been identified with features in the seafloor magnetic record, are suggested to be events of a similar nature, most likely times of anomalously low geomagnetic intensity. In addition to the Miocene magnetostratigraphic results given, several sets of averaged paleomagnetic inclinations are presented. Although these results clearly show the effects of a residual coring overprint, they demonstrate that paleomagnetic estimates of paleolatitudes can be made which are in good general agreement with ancient site positions calculated using hot spot-based plate reconstructions.

Description: We present Pleistocene oxygen and carbon isotope records from two planktonic foraminifer species (Globigerinoides sacculifer and Neogloboquadrina dutertrei) from Ocean Drilling Program Site 847 (0°16'N, 95°19'W; 3334 m water depth). An average sample resolution of 4500 yr was obtained by sampling at an interval of 15 cm through a continuous 35-m section from 0 to 1.15 Ma. Our d18O-based chronology is similar to that derived independently by astronomically tuning the gamma-ray attenuation porosity evaluator (GRAPE) record (Shackleton et al., 1995), though offsets as large as ± 30 k.y. occur on occasion. The surface waters at eastern equatorial Pacific Site 847, 380 km west of the Galapagos, are characterized by strong and constant upwelling, elevated nutrient concentrations, and high productivity. The isotopic composition of G. sacculifer (300-355 µm) reflects conditions in the thin-surface mixed layer, and the composition of N. dutertrei (355-425 µm) monitors the subsurface waters of the permanent shallow (10-40 m) thermocline. The Pleistocene d18O difference (N. dutertrei minus G. sacculifer, Dd18Od-s) averages 0.9 per mil and ranges from 0 per mil to 1.7 per mil. Neglecting species effects and shell size, the average Pleistocene d13C difference (G. sacculifer minus N. dutertrei, Dd13Cs-d) is 0.0 per mil and ranges from -0.5 per mil to 0.5 per mil. The Dd18Od-s and Dd13Cs-d records are used to infer vertical contrasts in upper ocean water temperature and nutrient concentration, though d13C may also be influenced by other factors, such as CO2 gas exchange. Variations in the isotopic differences are often synchronous with glacial/interglacial climate change. Glacial periods are characterized by smaller vertical contrasts in both temperature and nutrient concentration, and by notably greater accumulation rates of N. dutertrei and CaCO3. We attribute these responses to greater upwelling at the equatorial divergence. Superimposed on the glacial/interglacial Dd18Od-s pattern is a long-term trend possibly associated with the advection of Peru Current waters. The temporal fluctuations in the isotopic contrasts are strikingly similar to those observed at Site 851 (Ravelo and Shackleton, this volume), suggesting that the inferred changes in thermal and chemical profiles occurred over a broad region in the equatorial Pacific.

Description: This study investigates changes in the upper water column hydrography at Site 851 of the eastern tropical Pacific Ocean since the late Pliocene, using the oxygen and carbon isotopic composition of three species of planktonic foraminifers, each calcifying at different depths in the photic zone. The upper ocean seasonal hydrography in this region responds to the seasonally changing trade winds and thus is expected to respond to past changes in trade winds. One major change occurs at about 1.5 Ma, when the thermocline adjusts from a deep position to a shallower position. The thermocline remains in a relatively shallow position throughout the record up to recent time, with slight variations occurring synchronously with glacial/interglacial stages. In glacials, SSTs are probably a few degrees cooler and the thermocline is slightly deeper. From our knowledge of seasonal and interannual adjustments of the thermocline in this location, a deeper thermocline might be interpreted as either a decrease in the strength of the Equatorial Undercurrent (EUC) that results from lower mean wind strength or an increase in the Equatorial Countercurrent (ECC), which results from an increase in the strength of the southeasterly trade winds. A major shift from higher to lower carbon isotope values occurred at about 1.9 Ma, marking a transition to reduced planktonic-benthic d13C differences after 1.9 Ma. The carbon isotopic data indicate that changes in the carbon isotopic composition of intermediate upwelling water occurs at higher frequencies than the glacial/interglacial changes in ice volume.

Description: Two short time intervals centered at 2.3 and 4.7 Ma were studied to investigate short-term variations in surface-ocean processes as indicated by changes in the radiolarian microfossil population. These time intervals represent two different settings of late Neogene climate. The older interval represents a time when tropical circulation between the Pacific and Atlantic oceans was not blocked by the Isthmus of Panama, whereas the younger interval represents a time when Northern Hemisphere glaciation was present but did not display the dominance of the 100,000-yr cycle that characterizes the late Pleistocene. The younger time slice at 2.3 Ma was sampled at all Leg 138 sites except Site 844, where significant reworking was evident. All sites except 844, 853, and 854 were sampled for the older time slice. Samples were taken at 10- to 20-cm intervals at each site and spanned a GRAPE density maximum and minimum. Thus, it was possible to investigate whether the changes in carbonate content (as indicated by GRAPE density) were associated with changes in surface-ocean conditions (indicated by radiolarian assemblage variations). For both time slices, the radiolarian data indicate that intervals of decreased carbonate content are periods of cooler water conditions and possibly enhanced biogenic production. Times of increased carbonate content are associated with inferred warmer oceanographic conditions, as indicated by the dominance of tropical assemblages at 2.3 Ma and tropical and western Pacific assemblages during the time slice centered at 4.8 Ma. However, the spatial patterns of change during each time slice show a distinct difference in the mapped patterns of radiolarian assemblage dominance. The older time slice, representing a period before the closing of the Isthmus of Panama, shows more zonal patterns presumably associated with a more zonal character of equatorial circulation. After the closing of the isthmus, the shifts in faunal patterns between times of high and low carbonates are characterized by shifts in the dominance of the tropical and transitional assemblages, respectively, throughout the region.

Description: A group of 46 radiolarian species was used in this study of Leg 138 sites. The recovery of the sections was complete in the intervals that were cored using the APC system and nearly complete in the deeper sections. The northeastern sites (844 and 845) were sampled down through the middle Miocene into the uppermost part of the lower Miocene (middle part of the Calocycletta costata Zone). In the southeastern sites and those of the eastern transect (846 through 854) sediments were of late Miocene age (Diartus petterssoni Zone) and younger. Preservation of the radiolarian fauna was good to moderately good in most of the sites. Only in Sites 853 and 854 was the section older than late Pliocene barren of radiolarians. Reworked older radiolarians were found in the upper Miocene and Pliocene parts of the sections in most sites. Reworked upper Miocene radiolarians were even found in the upper Pliocene of Sites 853 and 854 where the upper Miocene part of the sections were barren of radiolarians. The development of an orbitally tuned time scale for the last 10 m.y. allowed the differentiation between radiolarian datums that appear to be synchronous (within 150,000 yr) in the eastern equatorial Pacific Ocean and those which appear to be diachronous. Of the 39 datums examined in this time interval, only 10 met this working definition of synchrony within the study area.

Description: We determined phosphorus (P) concentrations in Leg 138 sediment samples from Sites 844, 846, and 851, using a sequential extraction technique to identify the P associated with five sedimentary components. Total concentrations of P (sum of the five components) ranged from 4 to 35 µmol P/g sediment, with mean values relatively similar between the three sites (11, 14, and 12 for Sites 844,846, and 851, respectively). Authigenic/biogenic P was the most important component in terms of percentage of total P (about 75%), with iron-bound P (13%), adsorbed P (2%-9%), and organic P (4%) of secondary importance; detrital P was a minor P sink (1%) in these sediments. Profiles of adsorbed P and iron-bound P show decreasing concentrations with age, indicating that these components have been affected by diagenesis and reorganization of P. A peak in iron-bound P may reflect higher fluxes of hydrothermally derived Fe to eastern equatorial Pacific Ocean sediments from 11 to 8 Ma. Lower detrital P values for western Site 851 reflect a greater distance of this site from a terrigenous source area, compared to that of Sites 844 and 846. Phosphorus mass accumulation rates (P-MARs; units of µmol P/cm**2/k.y.) were calculated using total P concentrations (not including the minor and oceanically unreactive detrital P component) and sedimentation rates and dry-bulk densities averaged over time intervals of 0.5 m.y. P-MARs generally decrease from 17 Ma to the present. Eastern transect Sites 844 and 846 display a decrease in P-MARs from about 30 to 10 in the interval from 17 to 8 Ma, while western transect Site 851 is highly variable during this interval. P-MARs increase to about 45 and stay relatively high from 8 to 6 Ma, then decrease toward the present to some of the lowest values of the record (about 10). The general trend of high P-MARs at about 6 Ma and decreasing values toward the present is correlated with other geochemical and sedimentary trends through this interval and may reflect (1) a change in net sediment and P burial, (2) a reorganization of fluxes with no change of net burial, or (3) a combination of the two.

Description: Neogene calcareous sediments were recovered at 11 sites along two north-south transects in the eastern equatorial Pacific Ocean during Ocean Drilling Program (ODP) Leg 138. An overview of planktonic foraminifer distribution in these sediments was presented in Mayer, Pisias, Janecek, et al. (1992) based on a preliminary examination of core-catcher samples. In general, the preservation state of the foraminifers is poor throughout most of the sedimentary sequences, making this microfossil group here of much less value for biostratigraphy than other microfossil groups. Pliocene-Pleistocene planktonic foraminifers from several sites have been analyzed in great detail for their oxygen and carbon isotope composition in various high-resolution studies (Farrell et al., this volume; Mix et al., this volume; Ravello et al., this volume; Shackleton et al., this volume). Planktonic foraminiferal datums of biostratigraphic value have been identified in several of these studies. This report presents planktonic foraminiferal distribution in selected Miocene sediments.

Description: The biostratigraphic distribution and abundance of middle Miocene to Pleistocene silicoflagellates is documented from Ocean Drilling Program (ODP) Leg 138 Holes 844B, 847B, 848B, 849B, 850B, 85 IB, 852B, and 854B from the eastern Equatorial Pacific Ocean. The silicoflagellates were generally abundant and well preserved and frequently exhibited an unusually large range of variation. The upper Miocene of near-equatorial sites includes an assemblage of Bachmannocena diodon nodosa, which includes a bridge across the width of the basal ring. Stratigraphically below this, at sites within 5° of the equator is a lengthy interval of specimens of Distephanus speculum tenuis, which have a fragile apical structure. Both the intervals of Bachmannocena diodon nodosa plexus and Distephanus speculum tenuis are biostratigraphically useful within 5° of the equator, but are less useful beyond that. An unusual range of variation also is observed for Dictyocha in the Pliocene sediments at about the point where D. perlaevis and D. messanensis appear in the geologic record. This variation may be explained by hybridization between diverging species.

Description: A newly constructed record of eolian dust accumulation from the central North Pacific shows that dust deposition increased by an order of magnitude quite rapidly at 3.6 Ma. We associate this sudden drying with the uplift of at least the northern portion of the Tibetan Plateau, shutting off the Indian Ocean moisture source to central and western China. This ten-fold increase in atmospheric dust loading appears to be associated with the 1-m.y.-long shift toward heavy d18O values that occurred at 3.6-2.6 Ma. The dust grain-size record of wind intensity begins its late Cenozoic coarsening a million years before the drying event, at ~4.5 Ma. The northern hemisphere cooling that results in intensification of the subpolar westerly winds may have as its ultimate cause the drawdown of atmospheric CO2 in the latest Miocene and the early Pliocene closing of the Panamanian Seaway.

Description: Free and 'bound' long-chain alkenones (C37:2 and C37:3) in oxidized and unoxidized sections of four organic matter-rich Pliocene and Miocene Madeira Abyssal Plain turbidites (one from Ocean Drilling Program site 951B and three from site 952A) were analyzed to determine the effect of severe post depositional oxidation on the value of Uk'37. The profiles of both alkenones across the redox boundary show a preferential degradation of the C37:3 compared to the C37:2 compound. Because of the high initial Uk'37 values and the way of calculating the Uk'37 this degradation hardly influences the Uk'37 profiles. However, for lower Uk'37 values, measured selective degradation would increase Uk'37 up to 0.17 units, equivalent to 5°C. For most of the Uk'37 band-width, much smaller degradation already increases Uk'37 beyond the analytical error (0.017 units). Consequently, for interpreting the Uk'37 record in terms of past sea surface temperatures, selective degradation needs serious consideration.

Description: A simple, untuned "constant sedimentation rate" timescale developed using three radiometric age constraints and eleven d18O records longer than 0.8 Myr provides strong support for the validity of the SPECMAP timescale of the late Quaternary (Imbrie et al., 1984). In particular, the present study independently confirms the link between major deglaciations (terminations) and increases in northern hemisphere summer radiation at high latitudes and shows that this correlation is not an artifact of orbital tuning. In addition, the excess ice characteristic of late Quaternary "100-kyr" climate cycles typically accumulates when July insolation at 65°N has been unusually low for more than a full precessional cycle, or 〉21 kyr, and once established does not last beyond the next increase in summer insolation. Thus, the timing of the growth and decay of large 100-kyr ice sheets, as depicted in the deep sea d18O record, is strongly (and semipredictably) influenced by eccentricity through its modulation of the orbital precession component of northern hemisphere summer insolation.

Description: To understand the late Cenozoic glacial history of the Northern Hemisphere, continuous long-term proxy records from climatically sensitive regions must be examined. Ice-rafted debris (IRD) from Ocean Drilling Program (ODP) Site 918, located in the Irminger Basin, is one such record. IRD in marine sediments is a direct indicator of the presence of glacial ice extending to sea level on adjacent landmasses, and, therefore, is an important paleoclimatic signal from the mid- to high latitudes. The IRD record at Site 918 is the first long-term ice-rafting record available for southeast Greenland, a region that may have been a key nucleation area for widespread glaciation during the late Cenozoic (Larsen et al, 1994, doi:10.2973/odp.proc.ir.152.1994). This data report presents the results of coarse sand-size IRD mass accumulation rate (MAR) analyses for Site 918 from the late Miocene through the Pleistocene. In addition, a preliminary analysis of IRD compositions is included. Detailed discussions of the local, regional, and global paleoclimatic implications of this data, and of the companion Site 919 Pleistocene IRD MAR data (Krissek, 1999, doi:10.2973/odp.proc.sr.163.118.1999), are in preparation. Such future work will include comparisons of these IRD MAR data sets to the Site 919 oxygen isotope stratigraphy developed by Flower (1998, doi:10.2973/odp.proc.sr.152.219.1998).

Description: Coring during Ocean Drilling Program and Deep Sea Drilling Project Legs 163, 152, 104, 81, and 38 recovered sequences of altered basalt from North Atlantic seaward-dipping reflector sequences (SDRS) erupted during the initial rifting of Greenland from northern Europe and likely associated with excessive mantle temperatures caused by an impacting mantle plume head. Cr-rich spinel is found abundantly as inclusions and groundmass crystals within the olivine-rich lavas of Hole 917A (Leg 152) cored into the Southeast Greenland SDRS, but only rarely as inclusions within plagioclase in the lavas of the Vøring Plateau SDRS, and it is absent from other cored SDRS lavas from the Rockall Plateau and Southeast Greenland. Eruptive melt compositions determined from inferred, thermodynamically-defined, spinel-melt exchange equilibria indicate that the most primitive melts represented by Hole 917A basalts have Mg/(Mg + Fe2+) at least as high as 0.70 and approach near-primary mantle melt compositions. In contrast, Cr-rich spinels from Hole 338 (Leg 38) lavas on the Vøring Plateau SDRS give evidence for melt with Mg/(Mg + Fe2+) only as high as 0.64. This study underlines that primitive melts similar to those from Hole 917A comprise only a small fraction of the eruptive North Atlantic SDRS melts, and that most SDRS basalts were, in fact, too evolved to have precipitated Cr-rich spinel, with true melt Mg/(Mg + Fe2+) likely below 0.60. The evolved nature of the SDRS basalts implies large amounts of fractionation at the base of the crust or deep within it, consistent with seismic results that indicate an abnormally thick Layer 3 underlying the SDRS.

Description: The magnetic polarity stratigraphy at Site 907 obtained from the shipboard pass-through magnetometer and from discrete samples is readily interpretable back to the onset of the Gilbert Chron (5.89 Ma). From this level to the base of the section at ~14 Ma, the interpretation is corroborated by silicoflagellate datums with predictable correlation to polarity chrons. The resulting magnetostratigraphic interpretation differs from those proposed in the Leg 151 (Hole 907A) and 162 (Holes 907B and 907C) Initial Reports volumes. An important hiatus in the 7-10 Ma interval at Site 907 caused sedimentation to slow or cease for ~2.7 m.y. We have revised the shipboard correlation among the three holes at Site 907, resulting in a new composite section splice and recalculation of composite depths. For Site 985, magnetostratigraphic interpretation is possible down to ~150 meters below seafloor (mbsf) (C3An/C3Ar) at ~6 Ma. There are no useful biostratigraphic datums from Site 985 to support this interpretation; however, the interpretation is supported by the correlation of Sites 985 and 907 using natural gamma data from the shipboard multisensor track. Below ~150 mbsf at Site 985, drilling-related deformation at the onset of extended core barrel drilling precluded magnetostratigraphic interpretation.

Description: Cores recovered at Sites 986 and 987 comprise glacial fan sedimentation associated with the Svalbard-Barents Sea and Greenland Ice Sheets, respectively. At Site 986, the top 150 m and the basal 250 m yielded interpretable magnetic stratigraphies. The record from the intervening 550 m is compromised by drilling-related core deformation, poor recovery, and numerous debris flows. The uppermost 150 m appears to record the Brunhes/Matuyama boundary and the Jaramillo Subchron. The base of the drilled section (at ~950 meters below seafloor [mbsf]) is interpreted to lie within the Matuyama Chron (age 〈2.58 Ma) with an apparent normal polarity interval in the ~730-750 mbsf interval. Dinoflagellate cyst biostratigraphy and Sr isotopic ratios are consistent with a Matuyama age for the base of the drilled section and with the normal polarity interval as the Olduvai Subchron. On the other hand, the last occurrence of Neogloboquadrina atlantica (sinistral) and the last common occurrence of the warm-dwelling Globigerina bulloides at 647-650 mbsf in Hole 986D indicate an age for this level of ~2.3 Ma, inconsistent with the designation of the Olduvai Subchron in the ~730-750 mbsf interval. If the age at 647-650 mbsf in Hole 986D is taken as 2.3 Ma and the base of the hole lies within the Matuyama Chron, then the sedimentation rate in the basal 300 m of the cored section averages 1 m/k.y. At Site 987, the magnetic stratigraphy is fairly unambiguous throughout the section and yields an age of 7.5 Ma (Chron 4n) for the base of the drilled section. The paucity of calcareous and siliceous microfossils precludes biostratigraphic corroboration of the magnetostratigraphic interpretation, although dinoflagellate cysts provide general support, particularly at the base of the section. The age model indicates relatively low sedimentation rates (~5 cm/k.y.) at the base of the section with rates at least four to five times greater during intervals of debris flows at ~5-4.6 and ~2.6 Ma.

Description: Selected calcareous nannofossils were investigated by means of quantitative methods in middle and upper Miocene sediments from the tropical Indian Ocean (ODP Leg 115) and equatorial Pacific Ocean (DSDP Leg 85, ODP Legs 130 and 138). Our goal was to test the reliability of the classic biohorizons used in the standard zonations of Martini (1971) and Bukry (1973) and, possibly, to improve biostratigraphic resolution in the Miocene. In a time interval of about 8 m.y., from the last occurrence (LO) of S. heteromorphus (~13.6 Ma) to the LO of D. quinqueramus (~5.5 Ma), a total 37 events were investigated, using both the conventional and some additional markers proposed in the literature. At least 17 of these events proved to be distinct biostratigraphic correlation lines between the two considered areas. This integrated biostratigraphic framework increases the biostratigraphic resolution in the middle-upper Miocene interval (of the order of about 0.5 m.y). All the investigated events were tied to the geomagnetic polarity time scale (GPTS) and compared to biomagnetostratigraphy from mid-latitude North Atlantic Site 94-608 (Olafsson, 1991; Gartner, 1992), thus obtaining further information about the biostratigraphic and biochronologic reliability of the investigated events and a significant improvement of the available nannofossil biomagnetostratigraphic model for the middle and late Miocene.

Description: Analyses of Re, Os, and Ir concentrations, as well as Os-isotopic compositions, are reported for a suite of sediments from Ocean Drilling Program Site 959. These samples vary in age from late Neogene to Late Cretaceous, and represent a range in depositional oxidation-reduction conditions from suboxic in the Neogene to anoxic in the Late Cretaceous. Age assignments based on shipboard biostratigraphic data are used to calculate initial 187Os/186Os ratios of Neogene nannofossil/foraminifer oozes and Eocene to upper Oligocene laminated diatomites. These calculated initial ratios are in general agreement with published data constraining the Os-isotopic evolution of seawater through time, indicating that the Os-isotopic composition of these sediments is controlled largely by the Os isotopic composition of contemporaneous seawater. Results from analyses of Upper Cretaceous to lower Paleocene claystones do not exhibit elevated Ir concentrations and exhibit Re-Os systematics that are highly consistent with closed-system production of 187Os by in situ 187Re decay. Scatter in both the Cretaceous and Cenozoic data sets is likely the result of the influence of nonhydrogenous Os, carried by clastics, on the bulk sediment Os-isotopic composition, or post-depositional mobility of Re and/or Os.

Description: Diffuse reflectance records from Feni Drift in the North Atlantic faithfully record sediment percent carbonate. A high-resolution, reflectance-based age model for these sediments derived from an orbitally tuned age model for western equatorial Atlantic, Ceara Rise sediments was generated by spectral frequency mapping. Power spectra of the Feni Drift record indicate statistically significant sub-Milankovitch cyclicity at 7.6-8.4 and 4.8-6.1 kyr. We infer that these ~8 and ~5 kyr cycles document a linkage between North and equatorial Atlantic climate given our ability to correlate these records. These climate cycles influence Atlantic basin carbonate prior to the intensification of Northern Hemisphere glaciation and thus must arise from some portion of the climate system other than the dynamics of large ice sheets. The presence of these peaks, which could be related to equatorial clipped precession, implies a possible non-linear response to Milankovitch forcing.

Description: Stable oxygen isotope data from four holes drilled at the Ocean Drilling Program Site 967, which is located on the lower northern slope of the Eratosthenes Seamount, provide a continuous record of Eastern Mediterranean surface-water conditions during the last 3.2 Ma. A high-resolution stratigraphy for the Pliocene-Pleistocene sequence was established by using a combination of astronomical calibration of sedimentary cycles, nannofossil stratigraphy, and stable oxygen isotope fluctuations. Sapropels and color cycles are present throughout the last 3.2 Ma at Site 967, and their ages, as determined by calibration against the precessional component of the astronomical record, are consistent with those estimated for the sapropels of the classical land-based marine sequences of the Punta Piccola, San Nicola, Singa, and Vrica sections (southern Italy). The Site 967 oxygen isotope record shows large amplitude fluctuations mainly caused by variations in surface water salinity throughout the entire period. Spectral analysis shows that fluctuations in the d18O record were predominantly influenced by orbital obliquity and precessional forcing from 3.2 to 1 Ma, and all main orbital frequencies characterize the d18O record for the last million years. The start of sapropel formation at 3.2 Ma indicates a possible link between sapropel formation and the build up of northern hemisphere ice sheets. The dominance of the obliquity cycle in the interval from 3.2-1 Ma further points to the sensitivity of Eastern Mediterranean climate to the fluctuations in the volume of Arctic ice sheets. An intensification of negative isotope anomalies at Site 967, relative to the open ocean, supports a link between high run-off (during warm periods) and sapropel formation. freshwater input would have inhibited deep-water formation, which led to stagnation of deeper waters. Comparison with the land sections also confirms that differential preservation and diagenesis play a key role in sapropel occurrence.

Description: An expanded and largely complete upper Paleocene to upper Eocene section was recovered from the pelagic cap overlying Allison Guyot, Mid-Pacific Mountains at Ocean Drilling Program (ODP) Site 865 (18°26'N, 179°33'W; paleodepth 1300-1500 m). Reconstructions show that the site was within a few degrees of the equator during the Paleogene. Because no other Paleogene sections have been recovered in the Pacific Ocean at such a low latitude, Site 865 provides a unique record of equatorial Pacific paleoceanography. Detailed stable isotopic investigations were conducted on three planktonic foraminiferal taxa (species of Acarinina, Morozovella, and Subbotina). We studied benthic foraminiferal isotopes at much lower resolution on species of Cibicidoides and Lenticulina, Nuttallides truempyi and Gavelinella beccariiformis, because of their exceptional rarity. The d18O and d13C stratigraphies from Site 865 are generally similar to those derived from other Paleocene and Eocene sections. The planktonic foraminiferal records at Site 865, however, include significantly less short-term, single-sample variability than those from higher-latitude sites, indicating that this tropical, oligotrophic location had a comparatively stable water column structure with a deep mixed layer and less seasonal variability. Low-amplitude (0.1-0.8 per mil) oscillations on timescales of 250,000 to 300,000 years correlate between the d13C records of all planktonic taxa and may represent fluctuations in the mixing intensity of surface waters. Peak sea surface temperatures of 24°-25°C occurred in the earliest Eocene, followed by a rapid cooling of 3-6°C in the late early Eocene. Temperatures remained cool and stable through the middle Eocene. In the late Eocene, surface water temperatures decreased further. Vertical temperature gradients decreased dramatically in the late Paleocene and were relatively constant through much of the Eocene but increased markedly in the late Eocene. Intermediate waters warmed through the late Paleocene, reaching a maximum temperature of 10°C in the early Eocene. Cooling in the middle and late Eocene paralleled that of surface waters, with latest Eocene temperatures below 5°C. Extinction patterns of benthic foraminifera in the latest Paleocene were similar to those observed at other Pacific sites and were coeval with a short-term, very rapid negative excursion in d13C values in planktonic and benthic taxa as at other sites. During this excursion, benthic foraminiferal d18O values decreased markedly, indicating warming of 4 to 6°C for tropical intermediate waters, while planktonic taxa show slight warming (1°C) followed by 2°C of cooling. Convergence of d18O values of planktonic and benthic foraminifera suggests that thermal gradients in the water column in this tropical location collapsed during the excursion. These data are consistent with the hypothesis that equatorial Pacific surface waters were a potential source of warm, higher salinity waters which filled portions of the deep ocean in the latest Paleocene. Oxygen isotopic data indicate that equator to high southern latitude sea surface thermal gradients decreased to as little as 4°C at the peak of the excursion, suggesting some fundamental change in global heat transport.

Description: The sediments recovered during Leg 138 provide a remarkable opportunity to improve the geological time scale of the late Neogene. We have developed new time scales in the following steps. First, we constructed age models on the basis of shipboard magnetostratigraphy and biostratigraphy, using the time scale of Berggren, Kent, and Flynn (1985). Second, we refined these age models using shipboard GRAPE density measurements to provide more accurate correlation points. Third, we calibrated a time scale for the past 6 m.y. by matching the high-frequency GRAPE density variations to the orbital insolation record of Berger and Loutre (1991); we also took into account d18O records, where they were available. Fourth, we generated a new seafloor anomaly time scale using our astronomical calibration of C3A.n (t) at 5.875 Ma and an age of 9.639 Ma for C5n.1n (t) that is based on a new radiometric calibration (Baksi, 1992). Fifth, we recalibrated the records older than 6 Ma to this new scale. Finally, we reconsidered the 6- to 10-Ma interval and found that this could also be partially tuned astronomically.

Description: A series of 1-atm. melting experiments on basaltic flows collected from Holes 918D and 989B in the oceanic succession of the East Greenland continental margin can be used to define possible phase equilibria and liquid lines of descent. A sample from Site 918 (Section 152-918D-108R-2) shows the melting order low-Ca pyroxene (1153ºC), augite (1182ºC), olivine (1192ºC), and plagioclase (1192ºC). A sample from Site 989 (Section 163-989B-10R-7) melts in the order of low-Ca pyroxene (1113ºC), augite (1167ºC), plagioclase (1177ºC), and olivine (1184ºC). In particular, the relatively early appearance of low-Ca pyroxene distinguishes the melting relations for the oceanic succession from those observed for the basaltic continental succession at Site 917. A basaltic andesite flow from the Middle Series at Site 917 (Section 152-917A-27R-4) shows the melting order of low-Ca pyroxene (1142ºC), plagioclase (1173ºC), and olivine (1173ºC). This melting order is difficult to reconcile with the observed large compositional variations in SiO2 and FeO for the Middle Series, which imply early magnetite fractionation. Major element considerations and rare-earth element modeling of the dacites of the Middle Series suggest that they formed by low extent of melting (〈20%) of continental hydrated gabbroic or mafic amphibolite at pressures 〈8 kbar. These crustally derived melts represent possible contaminants of basaltic magmas of the Lower and Middle Series at Site 917.

Description: Thirty-five samples from the drill core of the three Leg 163 sites (Sites 988, 989, and 990) off the southeast coast of Greenland were analyzed for 27 major, minor, and trace elements by X-ray fluorescence (XRF) and for 25 trace elements, including 14 rare-earth elements (REEs), by an inductively coupled plasma source mass spectrometer (ICP/MS). Sr- and Nd-isotope data are reported for seven samples and oxygen-isotope data are reported for 19 plagioclase separates. In addition, a reconnaissance survey of the composition of the main mineral phases, plagioclase, pyroxene, and oxides was determined on an electron microprobe to provide the basic information required for petrogenetic modeling. Olivine pseudomorphs are present in many of the samples, but in no case was an olivine grain found that was fresh enough to give a reliable analysis. The chemical and isotopic data recorded here were determined to provide a comparison with the larger data sets acquired by the Edinburgh, Copenhagen, and Leicester laboratories from both Legs 152 and 163 drill cores. This will permit a detailed comparison of the North Atlantic flood basalt province as a whole with the better known Columbia River, Deccan, and Karoo continental flood basalt provinces, for which substantial chemical data sets are already available at Washington State University.

Description: Voluminous, subaerial magmatism resulted in the formation of extensive seaward-dipping reflector sequences (SDRS) along the Paleogene Southeast Greenland rifted margin. Drilling during Leg 163 recovered basalts from the SDRS at 66ºN (Site 988) and 63ºN (Sites 989 and 990). The basalt from Site 988 is light rare-earth-element (REE) enriched (La(n)/Yb(n) = 3.4), with epsilon-Nd(t=60) = 5.3, 87Sr/86Sr = 0.7034, and 206Pb/204Pb = 17.98. It is similar to tholeiites recovered from the Irminger Basin during Leg 49 and to light-REE-enriched tholeiites from Iceland. Drilling at Site 989, the innermost of the sites on the 63ºN transect, was proposed to extend recovery of the earliest part of the SDRS initiated during Leg 152. These basalts are, however, younger than those from Site 917 and are compositionally similar to basalts from the more seaward Sites 990 and 915. Many of the basalts from Sites 989 and 990 show evidence of contamination by continental crust (e.g., epsilon-Nd(t=60) extends down to -3.7, 206Pb/204Pb extends down to 15.1). We suggest that the contaminant is a mixture of Archean granulite and amphibolite and that the most contaminated basalts have assimilated ~5% of crust. Uncontaminated basalts are isotopically similar to basalts from Site 918, on the main body of the SDRS, and are light-REE depleted. Consistent with previous models of the development of this margin, we show that at the time of formation of the basalts from Sites 989 and 990 (1) melting was at relatively shallow levels in a fully-fledged rift zone; (2) fragments of continental crust were present in the lithosphere above the zones of melt generation; and (3) the sublithospheric mantle was dominated by a depleted Icelandic plume component.

Description: This data report provides a systematic documentation of the low-temperature alteration associated with the formation of a volcanic-rifted margin by the quantification of alteration effects and vein mineralogy and distributions in basalts recovered on Leg 152 (Larsen, Saunders, Clift, et al., 1994, doi:10.2973/odp.proc.ir.152.1994). Basaltic rocks from Holes 917A and 918D have been investigated to provide a quantitative description of the extents of recrystallization and secondary mineral abundance resulting from low-temperature alteration and weathering. Only limited descriptions of alteration and secondary mineral distributions were undertaken on board ship during Leg 152, and the data presented here provide an essential complement to the shipboard logs of the limited amount of basalt recovered during Leg 163 from Sites 988, 989, and 990 (Duncan, Larsen, Allan, et al., 1996, doi:10.2973/odp.proc.ir.163.1996).

Description: During Ocean Drilling Program (ODP) Leg 162, five sites were drilled in the subpolar North Atlantic (Sites 980-984), three sites in the Nordic Seas (Sites 985-987), and two holes at Iceland Sea Site 907 (first drilled during ODP Leg 151). Carbonate sediments at the subpolar sites have generally common to abundant and well-preserved planktonic foraminifers, especially at Feni Drift Sites 980/981 and Rockall Plateau Site 982. Gardar Drift Site 983 and Bjorn Drift Site 984 featured greater concentrations of clay material and ice-rafted debris, diluting carbonate material in some intervals (particularly before ~1.8 Ma at Site 984). Nordic Seas Sites 907 and 985-987 feature generally rare to common and moderately well-preserved planktonic foraminifers only within the past 1 m.y., although Pliocene taxa are sparsely recorded at Site 986 on the Svalbard margin. Planktonic foraminifer datum levels are located to the section level where possible for the subpolar North Atlantic sites. Comparison to an integrated magnetostratigraphy and calcareous nannofossil stratigraphy shows that several datum levels are synchronous to within 5% of their published ages. In particular, the start of the Neogloboquadrina pachyderma (sinistral) Acme Zone (1.8 Ma), the first occurrence (FO) of Globorotalia inflata (2.09 Ma), the last occurrence (LO) of Globorotalia cf. crassula (3.3 Ma), and the FO of Globorotalia puncticulata (4.5 Ma) are judged synchronous in eastern sections of the subpolar North Atlantic. The LO of Neogloboquadrina atlantica (sinistral) occurs ~100-200 k.y. later relative to its mid-latitude North Atlantic age (2.41 Ma).

Description: Silicoflagellate assemblages were analyzed for the Miocene intervals recovered during Ocean Drilling Program (ODP) Leg 162. The middle and late Miocene are represented in Holes 907B (Iceland Plateau) and 982B (Rockall Plateau) by well-preserved silicoflagellates. A zonal scheme is presented, which improves previous attempts to establish a comprehensive silicoflagellate stratigraphy for this realm, based on an increased resolution given by the analysis of this largest-ever number of samples for the given interval (about three times as many as those studied for ODP Leg 104). The most important change is the replacement of the last appearance of Corbisema triacantha by the first appearance of Bachmannocena circulus apiculata as the top of the upper C. triacantha Zone/bottom of the B. c. apiculata Zone. In addition, two important bioevents (the first appearance of Bachmannocena diodon nodosa and the last appearance of Distephanus crux stradneri) allow the subdivision of the B. c. apiculata Zone into three new subzones: Caryocha spp. Subzone, D. c. stradneri Subzone, and B. d. nodosa Subzone (oldest to youngest, respectively). This zonal scheme is correlated with the standard calcareous nannoplankton zonation and tentatively correlated with the magnetic polarity time scale. A qualitative analysis of the changes in surface-water characteristics is given, based on the variation in abundances of the several silicoflagellate groups. This shows a replacement of silicoflagellates that are adapted to warm surface waters by those adapted to temperate surface waters during the middle Miocene. In turn, the latter are gradually replaced by those adapted to cool surface waters during the late Miocene. The taxonomy of the taxa encountered has been revised in an effort to bring together differing schools. Only one new taxon, Distephanus crux lockerii, is described herein.

Description: Magnetic polarity stratigraphies for Sites 980-984 are based on shipboard measurements from the pass-through magnetometer after alternating field (AF) demagnetization at a peak field of 25 mT and shore-based stepwise AF demagnetization of discrete samples. The characteristic magnetization component was determined after AF demagnetization removed the steep downward drill-string-related magnetic overprint. Peak AF fields in the 20-30 mT range were required to resolve the component, carried by magnetite, that was used to produce unambiguous Pliocene-Pleistocene magnetic stratigraphies at all five sites. At Sites 980 and 983, magnetic stratigraphies were resolved to the base of the recovered advanced hydraulic piston corer (APC) section, which lies in the Matuyama Chron (1r.2r) and Olduvai Subchron (2n), respectively. At Sites 981 and 982, magnetization intensities decrease sharply in the normal polarity zone corresponding to the Gauss Chron (2An), and magnetic stratigraphies below this level could not be resolved. At Site 984, the resolution of magnetic stratigraphy was curtailed at ~250 meters below seafloor (Olduvai Subchron) by core deformation at the base of the APC section and in the underlying extended core barrel section. As the magnetic stratigraphies at all four sites are unequivocal, polarity chron interpretations can be made without aid from the biostratigraphy. Mean sedimentation rates within polarity chrons have been calculated and Pliocene-Pleistocene biomagnetostratigraphic correlations tested.

Description: Multisensor track data, including magnetic susceptibility, gamma-ray attenuation porosity evaluator (GRAPE) wet bulk density, and natural gamma emission, were collected on all cores recovered during Ocean Drilling Program Leg 162. Data from the upper Pliocene and lower Pleistocene of Sites 981 and 984 are here compared to results from analyses of a limited set of discrete samples, including benthic foraminiferal isotopic composition, grain size, carbonate content, abundance of foraminifers and lithic particles, and clay mineralogy. Natural gamma emission most closely monitors the input of felsic terrigenous material to these two sites. Magnetic susceptibility also tracks felsic terrigenous input at Site 981 but appears to reflect a separate, more mafic, terrigenous component at Site 984. The GRAPE record does not correlate well with any discretely measured variable at Sites 981 or 984.

Description: Ocean Drilling Program Site 975 is located near the base of the Menorca Rise in the South Balearic Basin of the western Mediterranean Sea. Coring at this site penetrated the Pliocene/Miocene boundary and recovered a sequence of sediments that represent the final stages of salt deposition and the transition from evaporitic to open marine conditions at the end of the Miocene (Messinian). Detailed petrographic observations and bulk mineralogical analyses by X-ray diffraction form the basis for preliminary interpretations of depositional environments for this section. Gypsum is thought to have been deposited in an evaporating basin below wave base. Cycles consisting of a clay layer overlain by gypsiferous chalk, laminated gypsum, and finally pinch-and-swell gypsum suggest upsection increases in salinity. The gypsum section is overlain by two exotic sand layers thought to mark events of fresher water (marine or meteoric) inflow to the basin. Gypsum deposition terminated and was replaced by inorganic precipitation of micritic calcite with periodic, variable dilution by fine-grained terrigenous sediment. The micritic sediments have fine, slightly wavy, laminations indicating either an algal/microbial mat origin, or varve-like fluctuations in deposition, perhaps in a deep basin. The Pliocene/Miocene boundary falls within an interval of banded micritic silty clays that reflect the final environmental fluctuations during the transition to the open marine conditions of the Pliocene.

Description: Upper Miocene to Pleistocene hemipelagites and resedimented facies recovered at Holes 976B and 977A (Leg 161) in the Alboran Basin consist mainly of biogenic and detrital components, with a minor contribution of neoformed mineral phases. Diagenetic processes have not obliterated the primary deposition signal, and therefore detrital components (quartz, feldspar, detrital dolomite, rock fragments, and clays) provide information about source rocks and provenances. No major bulk or clay mineralogy differences were recognized between resedimented and hemipelagic facies; in fact, similar mineral assemblages in both types of facies suggest common source rocks. However, mineral abundance fluctuations can be related to climate variations and tectonic factors, as the main controls of sediment fill of this basin. A marked increase in smectites in Messinian sediments suggests an extensive development of soils during that time, probably favored by the alternation of wet and dry climate episodes and the relative aridification of the Mediterranean borderlands. A notable increase in detrital components suggests a sea-level fall and/or tectonic uplift during the late Pliocene. The significant increase in detrital dolomite in the uppermost Pliocene deposits suggests the uplift of dolomite-rich rocks as source areas. Mineral components in Pleistocene sediments indicate increasing tectonic stability, and clay-mineral fluctuations during the Pleistocene can be related not only to tectonic events, but also to alternating cooling and warming periods.

Description: During Leg 138, we measured reflectance spectra in the visible and near-infrared bands (455-945 nm) every few centimeters on split core surfaces from eastern tropical Pacific Ocean sediments. Here, we evaluate predictions of the content of biogenic calcite, biogenic opal, and nonbiogenic sediments from the reflectance spectra. For Sites 844 through 847, which contain a significant nonbiogenic component, reflectance spectra yielded a useful proxy for the percentages of CaCO3 over a wide range of values from nearly 0% to 100%, with root-mean-square (RMS) errors of about 9%. Direct estimates of "nonbiogenic" sediment percentages, approximated by 100 - (CaCO3 + opal), were reasonably successful (RMS error of 10%), however, were incorrect in some intervals. This suggests that mineralogy of the nonbiogenic material changes through time and that further subdivision of this component will be needed for useful estimation from reflectance. For percentages of biogenic opal, calibration equations appear to work well (RMS error of 6%) at concentrations of less than 30%, but for higher opal concentrations, reflectance equations often underestimate the true contents of opal. Improvements in multiparameter lithologic estimates from reflectance spectra may come from (1) expanding the wavelengths measured to better capture unique mineral reflectance bands, and (2) adding the ability to measure diffuse, rather than directional, reflectance to minimize the effects of surface roughness.

Description: Cores from four Ocean Drilling Program (ODP) sites were examined for planktonic foraminifers. One sample per core (from core-catchers in Holes 806B and 807B and from Section 4 in Holes 847B and 852B) was examined through the interval representing the last 5.8 m.y. Sites 806 (0°19.1'N; 159°21.7'E) and 847 (0o12.1'N; 95°19.2'W) are beneath the equatorial divergence zone. Sites 807 (3°36.4'N; 156°37.5'E) and 852 (5°19.6'N; 110°4.6'W) are located north of the equator in the convergence zone created by the interaction of the westward-flowing South Equatorial Current (SEC) and the eastward-flowing North Equatorial Countercurrent (NECC). Specimens were identified to species and then grouped according to depth habitat and trophic level. Species richness and diversity were also calculated. Tropical neogloboquadrinids have been more abundant in the eastern than in the western equatorial Pacific Ocean throughout the last 5.8 m.y. During the mid-Pliocene (3.8-3.2 Ma), their abundance increased at all sites, while during the Pleistocene (after ~ 1.6 Ma), they expanded in the east and declined in the west. This suggests an increase in surface-water productivity across the Pacific Ocean during the closing of the Central American seaway and an exacerbation of the productivity asymmetry between the eastern and western equatorial regions during the Pleistocene. This faunal evidence agrees with eolian grain-size data (Hovan, 1995) and diatom flux data (Iwai, this volume), which suggest increases in tradewind strength in the eastern equatorial Pacific that centered around 3.5 and 0.5 Ma. The present longitudinal zonation of thermocline dwelling species, a response to the piling of warm surface water in the western equatorial region of the Pacific, seems to have developed after 2.4 Ma, not directly after the closing of the Panama seaway (3.2 Ma). Apparently, after 2.4 Ma, the piling warm water in the west overwhelmed the upwelling of nutrients into the photic zone in that region, creating the Oceanographic asymmetry that exists in the modern tropical Pacific and is reflected in the microfossil record. In the upper Miocene and lower Pliocene sediments, the ratio of thermocline-dwelling species to mixed-layer dwellers is 60%:40%. During the mid-Pliocene, the western sites became 40% thermocline and 60% mixed-layer dwellers. Subsequent to -2.4 Ma, the asymmetry increased to 20%: 80% in the west and the reverse in the east. This documents the gradual thickening of the warm-water layer piled up in the western tropical Pacific over the last 5.8 m.y. and reveals two "steps" in the biotic trend that can be associated with specific events in the physical environment.

Description: Water column and core-top d15N data show that Arabian Sea denitrification produces large nitrogen isotopic enrichments that are regionally recorded with fidelity in the sediments. These results facilitate interpretation of a 1 m.y. d15N record for Ocean Drilling Program site 722B on the Owen Ridge in terms of climatically linked oscillations in denitrification at the major orbital periods. As at present, denitrification was greatest during interglacial periods and, apparently, was not active during most glacial intervals. Cross-spectral analysis of d15N with foraminiferal d18O (global climate/sea level index) and lithogenic grain size (monsoon strength index) suggests forcings by changes in hydrography and productivity acting through the extent and intensity of the oxygen minimum zone. The data suggest that denitrification may be an internal forcing mechanism for climate change during major glacial/interglacial transitions through influence on marine N inventory and atmospheric CO2. However, compensation or amplification may occur from other sinks (sediment denitrification) or sources (nitrogen fixation).

Description: Sediments recovered during Ocean Drilling Program (ODP) Leg 138 in the eastern equatorial Pacific Ocean were analyzed for variations in eolian accumulation rate and mean grain-size. Latitudinal and temporal patterns of these parameters showed important changes in the intensity of atmospheric circulation and eolian flux associated with the intertropical convergence zone (ITCZ) and suggested that eolian input parameters could be used to define its paleoposition through time. Modern atmospheric circulation in the equatorial region is weakest in the intertropical convergence zone and increases as the trade winds are approached to the north and south. Thus, the expected spatial pattern of eolian grain size would have the finest material deposited beneath the ITCZ and a coarsening of material in both directions away from this zone. Sediments from ODP Leg 138 show this pattern for much of the Pleistocene and Pliocene but, prior to about 4 Ma, begin to lose the northern coarse component suggesting that the ITCZ was located north of its present position during the late Miocene. Eolian flux records also show a latitudinal pattern of deposition associated with the position of the ITCZ that, similar to eolian grain-size variability, suggests a more northerly position of the ITCZ during the late Miocene. Overall, the regional input of eolian material to the equatorial Pacific has decreased throughout the late Neogene. This reduction in eolian input reflects climatic changes to relatively wetter conditions in the continental eolian source regions beginning during the late Pliocene.

Description: The design and operations of a low cost, high rate thermal cycling facility designed for LEO conditions is described. Thermal cycling facilities were constructed with various design criteria. Some were designed to duplicate as closely as possible the conditions a cell or module would encounter while in orbit about the Earth. A typical facility to perform this type of cycling was a large vacuum system with liquid nitrogen cooled walls. The cells were heated by an AMO spectrum solar simulator, then a shutter was closed allowing the cells to give up their heat to the cold walls. This system was good at duplicating the orbital conditions but was slow and very costly to operate. Other systems used a gas atmosphere and heated the cells with radiant heat and cooled the cells by moving them into close proximity to a cold plate. The systems greatly increased the cycle times. Other systems moved the heating and cooling atmosphere into and out of the test areas and achieved reasonable cycle rates. All these systems, however, are expensive to operate.

Description: The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

Description: The solar array for the San Marco D/L spacecraft is described and the performance of 4 GaAs solar cell panels are examined. In comparison to the typical Si solar cell panel for San Marco D/L, it is shown that each GaAs solar cell panel provides at least 23 percent more specific power at maximum output and 28 deg C. Also described here, are several measurements that will be made to evaluate the relative performance of Si and GaAs solar cell panels during the San Marco D/L flight.

Description: The results of heteroepitaxial growth of GaAs and GaAlAs directly on Si are presented, and applications to new cell structures are suggested. The novel feature is the elimination of a Ge lattice transition region. This feature not only reduces the cost of substrate preparation, but also makes possible the fabrication of high efficiency monolithic cascade structures. All films to be discussed were grown by organometallic chemical vapor deposition at atmospheric pressure. This process yielded reproducible, large-area films of GaAs, grown directly on Si, that are tightly adherent and smooth, and are characterized by a defect density of 5 x 10(6) power/sq cm. Preliminary studies indicate that GaAlAs can also be grown in this way. A number of promising applications are suggested. Certainly these substrates are ideal for low-weight GaAs space solar ells. For very high efficiency, the absence of Ge makes the technology attractive for GaAlAs/Si monolithic cascades, in which the Si substrates would first be provided with a suitable p/n junction. An evaluation of a three bandgap cascade consisting of appropriately designed GaAlAs/GaAs/Si layers is also presented.

Description: Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Description: A short circuit current (I sub sc) degradation model for gallium arsenide (GaAs) solar cells irradiated by protons from low energy to 100 MeV was developed. This model was found to be satisfactory in predicting the I sub sc degradation of GaAs cells, but not that of silicon (Si) cells. A modification to the aforementioned model that preserves the optical wavelength dependency in the photogeneration of minority carrier pairs was described herein. Spectral Si and GaAs response and I sub sc for the Si and GaAs solar cells were discussed, and also were presented in graph form. The overall predictability of the modified model was deemed to be satisfactory.

Description: Manufacturing technology for mass producing high efficiency GaAs solar cells is discussed. A progress using a high throughput MO-CVD reactor to produce high efficiency GaAs solar cells is discussed. Thickness and doping concentration uniformity of metal oxide chemical vapor deposition (MO-CVD) GaAs and AlGaAs layer growth are discussed. In addition, new tooling designs are given which increase the throughput of solar cell processing. To date, 2cm x 2cm AlGaAs/GaAs solar cells with efficiency up to 16.5% were produced. In order to meet throughput goals for mass producing GaAs solar cells, a large MO-CVD system (Cambridge Instrument Model MR-200) with a susceptor which was initially capable of processing 20 wafers (up to 75 mm diameter) during a single growth run was installed. In the MR-200, the sequencing of the gases and the heating power are controlled by a microprocessor-based programmable control console. Hence, operator errors can be reduced, leading to a more reproducible production sequence.

Description: Various coatings developed in the FRG (i.e., second-surface mirrors with interference filters with and without conductive layers, conductive layers on solar-cell covers, and selective absorber coatings) have been qualified by accelerated tests under simulated space environment conditions. Experiments with coatings and solar cells have shown, however, that the thermo-optical behavior can differ considerably when performed on the ground and in space because of the great difficulty in simulating the space environment realistically. The objective of this experiment is to qualify these coatings under realistic space environment conditions. In addition, the experiment will provide design criteria, techniques, and test methods to insure control of the combined space and spacecraft environment effects, such as contamination, electrical conductance, and optical degradation, on the coatings. Data to be measured include the temperature of the samples, the electrical resistance of the conductive layers of the samples, the short circuit current of the solar-cell modules, and the deposition of contaminants on the samples (using quartz crystal microbalances (QCM's)).

Description: The objective of this experiment is to evaluate the synergistic effects of the space environment on various solar-array materials, including solar cells, cover slips with various antireflectance coatings, adhesive, encapsulants, reflector materials, substrate strength materials, mast and harness materials, structural composites, and thermal control treatments. The experiment is passive and consists of an arrangement of material specimens mounted in a 3-in.-deep peripheral tray. The effects of the space environment on the specimens will be determined by comparison of preflight and postflight measurements of mechanical, electrical, and optical properties.

Description: A model that explains the flat-spot power loss phenomenon is presented. Evidence suggests that the effect is due to localized metallurgical interactions between the silicon substrate and the contact metallization. These reactions are shown to result in localized regions in which the P-N junction is destroyed and replaced with a metal semiconductor-like interface. The effects of thermal treatment, crystallographic orientation, junction depth, and metallization are shown along with a method of preventing the effect through the suppression of vacancy formation at the free surface of the contact metallization. Data indicating the effectiveness of a TiN diffusion barrier in preventing the effect are also given.

Description: The NASA large flexible solar array space shuttle flight experiment is described. The 32 x 4 m wing is deployed from the shuttle bay, and experiments in electrical output, multiple deployment, and structural dynamics are planned. Both 2 x 4 cm and 5.9 x 5.9 cm cell assemblies on the array blanket are evaluated. Safety/hazards provisions are described, including emergency jettison provisions. Ground testing and hardware fabrication are summarized.

Description: A development program to produce 5.9 x 5.9 cm space quality silicon solar cells with a cost goal of 30 $/W is described. Cell types investigated include wraparound dielectric, mechanical wraparound and conventional contact configurations with combinations of 2 or 10 ohm/cm resistivity, back surface reflectors and/or fields, and diffused or ion implanted junctions. A single step process to cut cell and cover glass simultaneously is being developed. Results for cell and array tests are given. Large solar arrays that might use cells of this type are discussed.

Description: Objectives and progress in both low concentration ratio (6 to 10) and high concentration ratio ( 100) array developments are summarized. Problems encountered include: thermal control, maldistribution of concentrated sunlight, current busing, and optical surface degradation. The potential advantages over planar arrays are an order of magnitude reduction in per unit cost of power plus increased immunity to radiation damage.

Description: The design and structural properties of a low concentration ratio solar array are discussed. The assembled module consists of six interconnected containers which are compactly stowed in a volume of 3.24 m(3) for delivery to orbit by the shuttle. The containers deploy in accordian fashion into a rectangular area of 19.4 x 68 meters and can be attached to the user spacecraft along the longitudinal centerline of the end container housing. Five rotary incremental actuators requiring about 8 watts each will execute the 180-degree rotation at each joint. Deployable masts (three per side) are used to extend endcaps from the housing in both directions. Each direction is extended by three masts requiring about 780 watts for about 27 minutes. Concentrator elements are extended by the endcaps and are supported by cable systems that are connected between the housings and endcaps. These power generating elements contain reflector panels which concentrate light onto the solar panels consisting of an aluminum radiator with solar cells positioned within the element base formed by the reflectors. A flat wire harness collects the power output of individual elements for transfer to the module container housing harnesses.

Description: Participants expressed more interest in GaAs cells than in Si cells. For silicon cells, the beginning of life efficiency is not a major problem but more research is needed in the end of life efficiency. The beginning of life efficiency of GaAs cells must be brought up to 20% at AMO. More proton damage tests must be conducted. Liquid phase epitaxy technology is current but chemical vapor deposition technology is more flexible. There are no obvious problems in limiting process yields. Technology transfer should occur when market demands are generated.

Description: Principles and design considerations of IR transparent solar arrays are discussed. Optimization of performance of flexible solar arrays was studied. Measured solar absorptance as low as alpha s = 0.59 was achieved which leads to a predicted BOL power density of 182.7 = W/square meters. Advanced array concepts, system level cascaded panels, and transparent rigid panels are proposed and expected benefits discussed.

Description: A number of structurally efficient configurations for wing-type solar arrays are developed by a combination of deepening the planform of the blanket and structure and by partitioning the blanket with battens and frequent attachments to the support structure. This technique reduces the tension required to avoid a low natural frequency for the blanket, and the load reduction results in a lighter structure. The use of three different structures are investigated: the Astromast, the Extendible Support Structure (ESS), and a new beam called the STACBEAM (Stacking Triangular Articulated Compact Beam) and their relative performances are compared. The investigation of the STACBEAM is emphasized because its sequential deployment is more reliable for very long systems, and its linear deployment facilitates local attachments to the blanket and the development of a low mass deployer.

Description: Structurally efficient ways to support the large solar arrays (3,716 square meters which are currently considered for space station use) are examined. An erectable truss concept is presented for the on orbit construction of winged solar arrays. The means for future growth, maintenance, and repair are integrally designed into this concept. Results from parametric studies, which highlight the physical and structural differences between various configuration options are presented. Consideration is given to both solar blanket and hard panel arrays.

Description: A miniaturized Cassegrainian concentrator (MCC) solar array system is examined to assess the practicality of assembling the basic MCC element into a total array system capable of producing multi-hundred kilowatts of power for Space Platform/Space Station or other low Earth orbit long lifetime missions. Preliminary mechanical and electrical subsystems are developed in order to determine first order performance characteristics. Results of the study support the feasibility of a 100-kilowatt MCC array system with beginning-of-life (BOL) performance of 160 watts per square meter and 28 W/kg. The performance numbers are based on 20 percent efficient (at operating temperature) solar cells and 0.25-millimeter thick electroformed nickel optics. These performance numbers can be improved upon significantly with the development of higher efficiency solar cells and/or lighter weight optics.

Description: High-efficiency, monolithic, two-color, three-terminal solar cells were fabricated by a novel growth technique, vacuum metal-organic chemical vapor deposition. The technique uses the expensive metal alkyls efficiently and toxic gases sparingly. The fact that the outer chamber is constructed of nonbreakable stainless steel is an attractive safety feature associated with this deposition system.

Description: Computer analysis was used to determine the AMO conversion efficiency of single-junction crystalline cells, two-cell and three-cell crystalline tandem structures operating under 100 suns and at 80 C. For optimally designed devices, the calculated efficiencies are 24% for single-junction cells, 33 to 35% for two-cell tandem structures, and 37 to 39% for three-cell tandem structures. Practical efficiencies are expected to be about 15 relative percentage points lower in each case.

Description: The short-circuit current reduction in GaAs shallow junction heteroface solar cells was calculated according to a simplified solar cell damage model in which the nonuniformity of the damage as a function of penetration depth is treated explicitly. Although the equivalent electron fluence was not uniquely defined for low-energy monoenergetic proton exposure, an equivalent electron fluence is found for proton spectra characteristic of the space environment. The equivalent electron fluence ratio was calculated for a typical large solar flare event for which the proton spectrum is PHI(sub p)(E) = A/E(p/sq. cm) where E is in MeV. The equivalent fluence ratio is a function of the cover glass shield thickness or the corresponding cutoff energy E(sub c). In terms of the cutoff energy, the equivalent 1 MeV electron fluence ratio is r(sub p)(E sub c) = 10(9)/E(sub c)(1.8) where E(sub c) is in units of KeV.

Description: Some n(+)/p cells in which lithium is introduced as a counterdopant, by ion-implantation, into the cell's boron-doped p-region were studied. To determine if the cells radiation resistance could be significantly improved by lithium counterdoping. Defect behavior was related to cell performance using deep level transient spectroscopy. Results indicate a significantly increased radiation resistance for the lithium counterdoped cells when compared to the boron doped 1 ohm-cm control cell. The increased radiation resistance of the lithium counterdoped cells is due to the complexing of lithium with divacancies and boron. It is speculated that complexing with oxygen and single vacancies also contributes to the increased radiation resistance. Counterdoping silicon with lithium results in a different set of defects.

Description: Telemetry from the Living Plume Shield's gallium arsenide solar panel experiment was evaluated to determine degradation. The data were culled to preclude spurious results from possible shadowing or inaccurate measurements on a cold array. Two independent methods were then used to obtain the maximum power points and the various characteristics of the solar array. Fill factor, open circuit voltage, short circuit current, and series and shunt resistances were examined. The data analysis concluded that, to date, nearly all of the solar array degradation is due to the reduction in the short circuit current.

Description: The radiation tolerance of the following three low resistivity, high voltage silicon solar cells was investigated: (1) the COMSAT MSD (multi-step diffused) cell, (2) the MinMIS cell, and (3) the MIND cell. A description of these solar cells is given along with drawings of their configurations. The diffusion length damage coefficients for the cells were calculated and presented. Solar cell spectral response was also discussed. Cells of the MinMIS type were judged to be unsuitable for use in the space radiation environment.

Description: Gallium Arsenide (GaAs) solar cells are viewed as a potential primary power source on certain future Earth orbiting satellites. However, the relative merits of gallium arsenide over silicon in a space radiation environment are largely unknown because a general degradation model for gallium arsenide does not exist. The results of a test simulating the proton radiation environment existing in a polar orbit and the concomitant effects on GaAs and thin silicon (Si) solar cells are presented. The objectives and methodology of the simulation test were discussed. The electrical characteristics of GaAs and Si solar cells are given in graph form. It was concluded that GaAs cells are viable for use on satellites in low Earth orbit.

Description: Significant discrepancies have been observed between predicted and actual in-orbit silicon solar array degradation in orbits other than LEO (low Earth orbits) and GEO (geosynchronous orbit). These discrepancies have been diagnosed to arise probably from a combination of a lack of appropriate solar cell test data and from inadequacies in the models that relate the unidirectional and mono-energetic proton test data to the omnidirectional flux-energy spectra actually found in orbit. Relative damage coefficients and solar cell power outputs were discussed, and also were presented in graph form. Silicon and gallium arsenide solar cells were considered.

Description: The radiation damage of solar cells has become a prime concern to the U.S. Air Force due to longer satellite lifetime requirements. Flight experiments were undertaken on the Navy Living Plume Shield (LPS) satellite and the NASA/Air Force Combined Release and Radiation Effects Satellite (CRRES) to complement existing radiation testing. Each experiment, the rationale behind it, and its approach and status are presented. The effect of space radiation on gallium arsenide (GaAs) solar cells was the central parameter investigated. Specifications of the GaAs solar cells are given.

Description: A computer program, SCAP2D (Solar Cell Analysis Program in 2-Dimensions), is used to evaluate the Etched Multiple Vertical Junction (EMVJ) and grating solar cells. The aim is to demonstrate how SCAP2D can be used to evaluate cell designs. The cell designs studied are by no means optimal designs. The SCAP2D program solves the three coupled, nonlinear partial differential equations, Poisson's Equation and the hole and electron continuity equations, simultaneously in two-dimensions using finite differences to discretize the equations and Newton's Method to linearize them. The variables solved for are the electrostatic potential and the hole and electron concentrations. Each linear system of equations is solved directly by Gaussian Elimination. Convergence of the Newton Iteration is assumed when the largest correction to the electrostatic potential or hole or electron quasi-potential is less than some predetermined error. A typical problem involves 2000 nodes with a Jacobi matrix of order 6000 and a bandwidth of 243.

Description: Several modifications were made to an infinite solution liquid phase epitaxy system that help fabricate both GaAs-based cells and thin cells that effectively reduce power-to-weight ratio for space applications. The most important development is the multiwell crucible for multilayer growth. Using a split crucible in one system, as many as five layers were grown in succession with varying Al levels and dopants. The structures grown were used to produce thin GaAs cells only 10 to 20 microns thick and also to grow cascade cell components. Results of these studies are presented and their applications to the future development of GaAs-based cells are discussed.

Description: A fabrication process for structurally stable thin solar cell wafers that produce good power output after irradiation is described. The fabrication process is as follows. A 6 mil, circular wafer is oxidized on both sides. One side is then patterned with a rectangular array of holes in the oxide that are nominally 75 mils square and separated by 2 mil spacings. Wells are then etched into the silicon with KOH to a depth of 4 mils, leaving a 2 mil, unetched thickness. Two areas on the surface are left unetched to provide pads for bonding or testing. All oxide is then removed and the rest of the processing is normal; the unetched face is used as the illuminated face. When all other processing is complete, a 2 X 2 cm cell is sawed from the starting wafer leaving a border that is approximately 10 mils wide. The effective thickness, determined by weighing an unmetallized sample, of such a cell is about 2.4 mil.

Description: The advanced photovoltaics-related experiments for investigating a portion of the solar spectrum and the effect of the space environment on photovoltaics. The information will be used to provide correlation between space and ground testing and also to provide for more accurate performance measurement in the laboratory. Specific objectives of these experiments are to provide information on the performance and endurance of advanced and conventional solar cells, to improve reference standards for photovoltaic measurements, and to measure the energy distribution in the extraterrestrial solar spectrum. Data to be obtained will include temperatures and short-circuit current of the samples. Six-point current-voltage (I-V) characteristics will be obtained for selected samples. These data will be recorded once a day during the flight. Orbit data will be correlated with preflight and postflight measurement of the samples.

Description: Current-voltage curves were calculated for each cell in a cascade structure using a solar cell diode equation and superposition. Terms for the light generated current, diffusion current, space charge recombination current and series and shunt resistance are included. Individual current voltage curves are added in series with ohmic resistance losses for the cell interconnects to obtain the cascade cell performance. Temperature was varied with concentration, using several models, and ranged from 55 C at one Sun to between 80 and 200 C at 100 Suns. A variety of series resistance and internal resistances were used. Coefficients of the diffusion and recombination terms are strongly temperature dependent. The study indicates that maximum efficiency (30%) occurs in the 50 to 100X Sun concentration range, provided series resistance is below 0.015 ohm-sq cm and cell temperature is 80 C at 100 Suns.

Description: Gallium and boron doped silicon solar cells, processed by ion implantation followed by either laser or furnace anneal were irradiated by 1 MeV electrons and their postirradiation recovery by thermal annealing was determined. During the postirradiation anneal, gallium doped cells prepared by both processes recovered more rapidly and exhibited none of the severe reverse annealing observed for similarly processed 2 ohm-cm boron doped cells. Ion implanted furnace annealed 0.1 ohm-cm boron doped cells exhibited the lowest post-irradiation annealing temperatures after irradiation. The drastically lowered recovery temperature is attributed to the reduced oxygen and carbon content of the 0.1 ohm-cm cells. Analysis based on defect properties and annealing kinetics indicates that further reduction in annealing temperature is attainable with further reduction in the silicon's carbon and/or divacancy content after irradiation.

Description: Low temperature Zn diffusion in GaSb, where the minimum temperature was 450 C, was studied. The pseudo-closed box (PCB) method was used for Zn diffusion into GaAs, AlGaAs, InP, InGaAs and InGaAsP. The PCB method avoids the inconvenience of sealed ampoules and proved to be simple and reproducible. The special design of the boat for Zn diffusion ensured the uniformality of Zn vapor pressure across the wafer surface, and thus the uniformity of the p-GaSb layer depth. The p-GaSb layers were studied using Raman scattering spectroscopy and the x-ray rocking curve method. As for the postdiffusion processing, an anodic oxidation was used for a precise thinning of the diffused GaSb layers. The results show the applicability of the PCB method for the large-scale production of the GaSb structures for solar cells.

Description: Indium phosphide is considered to be a strong contender for many photovoltaic space applications because of its radiation resistance and its potential for high efficiency. An overview of recent progress is presented, and possible future research directions for indium phosphide space solar cells are discussed. The topics considered include radiation damage studies and space flight experiments.

Description: Understanding solar cell response to pulsed laser outputs is important for the evaluation of power beaming applications. The time response of high efficiency GaAs and silicon solar cells to a 25 nS monochromatic pulse input is described. The PC-1D computer code is used to analyze the cell current during and after the pulse for various conditions.

Description: Four-terminal mechanically stacked solar cells were developed for advanced space arrays with line-focus reflective concentrators. The top cells are based on AlGaAs/GaAs multilayer heterostructures prepared by low temperature liquid phase epitaxy. The bottom cells are based on heteroepitaxial InP/InGaAs liquid phase epitaxy or on homo-junction GaSb, Zn-diffused structures. The sum of the highest reached efficiencies of the top and bottom cells is 29.4 percent. The best four-terminal tandems have an efficiency of 27 to 28 percent. Solar cells were irradiated with 1 MeV electrons and their performances were determined as a function of fluence up to 10(exp 16) cm(exp-2). It was shown that the radiation resistance of developed tandem cells is similar to the most radiative stable AlGaAs/GaAs cells with a thin p-GaAs photoactive layer.

Description: An investigation of solar cells based on AlGaAs/GaAs heterostructures with an internal Bragg reflector as the back-surface reflector is presented. The Bragg reflector is grown by low pressure metalorganic chemical vapor deposition on n-GaAs substrates in a horizontal resistively heated reactor. The Bragg reflector with its maximum reflectance centered at a wavelength of 860 nm consists of 12 pairs of AlAs/GaAs layers. The resulting Bragg reflector has a thickness of 0.072 micrometers for AlAs and 0.059 micrometers for GaAs. The multi-layered quasi-dielectric stack selectively reflects weakly absorbed photons with energies near to the GaAs band gap for a second pass through the photoactive region, thus increasing the photocurrent. The use of the Bragg reflector allows the external quantum efficiency to be increased in the long wavelength of the spectrum. The use of the Bragg reflector and an antireflective coating and prismatic cover allowed an efficiency of 23.4 percent to be obtained.

Description: The high efficiency solar cells based on multilayer AlGaAs/GaAs heterostructures, prepared by low temperature liquid phase epitaxy (LPE), were developed and tested. An investigation of the low temperature LPE process for the crystallization of AlGaAs heterostructures of as high as 24.0 to 24.7 percent under AMO conditions at concentration ratios of 20 to 100x, were reached. Developed solar cells show substantial radiation resistance to the damage induced by 3.75 MeV electrons.

Description: The present conference on electrochemical power sources encompasses systems of such types as the thermoelectric, advanced rechargeable, lithium reserve, rechargeable, and nonrechargeable, nickel-cadmium and nickel-hydrogen rechargeable, lead-acid, nickel-zinc and nickel-iron rechargeable, nickel-cadmium and nickel-hydrogen rechargeable, and fuel cells. Attention is given to Si-Ge alloy multicouple technology, sodium-sulfur battery development status, the safety aspects of a rechargeable lithium C cell, fiber-structure electrodes for nickel-cadmium batteries, energy density improvements in Li/carbon monofluoride cells, zinc-air button cell technology, catalyzed cathodes for Li/SOCl2 cells, the effect of polymer structure on the rate capability of the lithium-iodine cell, and a methanol fuel cell powerplant.

Description: A feasibility study has been conducted for a NASA Kennedy Space Center liquid hydrogen/liquid oxygen production facility using solar cell arrays as the power source for electrolysis. The 100 MW output of the facility would be split into 67.6 and 32 MW portions for electrolysis and liquefaction, respectively. The solar cell array would cover 1.65 sq miles, and would be made up of 249 modular 400-kW arrays. Hydrogen and oxygen are generated at either dispersed or centralized water electrolyzers. The yearly hydrogen output is projected to be 5.76 million lbs, with 8 times that much oxygen; these fuel volumes can support approximately 18 Space Shuttle launches/year.

Description: An investigation has been conducted in order to compile quantitative data on the reflective properties of metallic indium. The fabricated samples were of sufficiently high quality that differences from similar second-surface silvered mirrors were not apparent to the human eye. Three second-surface mirror samples were prepared by means of vacuum deposition techniques, yielding indium thicknesses of approximately 1000 A. Both hemispherical and specular measurements were made. It is concluded that metallic indium possesses a sufficiently high specular reflectance to be potentially useful in many solar energy applications.

Description: Lithium-counterdoped n(+)p silicon solar cells are found to exhibit significantly increased radiation resistance to 1-MeV electron irradiation when compared to boron-doped n(+)p silicon solar cells. In addition to improved radiation resistance, considerable damage recovery by annealing is observed in the counterdoped cells at T less than or equal to 100 C. Deep level transient spectroscopy measurements are used to identify the defect whose removal results in the low-temperature aneal. It is suggested that the increased radiation resistance of the counterdoped cells is primarily due to interaction of the lithium with interstitial oxygen.

Description: The cost involved in the performance of the standard operations for the manufacture of silicon wafers is insignificant in the case of space photovoltaics applications. It is, however, a decisive factor with respect to terrestrial applications of silicon photovoltaic devices. In 1975, a program was, therefore, begun to develop low cost silicon solar arrays for terrestrial applications. The goal was silicon-based photovoltaic (PV) modules ready for installation at a selling price of $0.50/watt (1975 dollars). Sheet and ribbon silicon growth held out the promise of reduced cost through continuous operation, high material throughput, high material utilization efficiency, and a product whose shape lent itself to the assembly of high packing density modules. Attention is given to ribbon growth technologies, sheet technology generic problems, and ribbon cell and module technology status. It is concluded that the potential for crystalline ribbon silicon appears to be better today than ever before.

Description: The present investigation is concerned with the formulation of energy management strategies for stand-alone photovoltaic (PV) systems, taking into account a basic control algorithm for a possible predictive, (and adaptive) controller. The control system controls the flow of energy in the system according to the amount of energy available, and predicts the appropriate control set-points based on the energy (insolation) available by using an appropriate system model. Aspects of adaptation to the conditions of the system are also considered. Attention is given to a statistical analysis technique, the analysis inputs, the analysis procedure, and details regarding the basic control algorithm.

Description: The NASA Lewis Research Center in cooperation with the World Health Organization, U.S.A. I.D., the Pan American Health Organization and national government agencies in some developing countries sponsored the installation of twenty photovoltaic powered medical vaccine storage refrigerator-freezer (R/F) systems. The Solar Power Corporation was selected as the contractor to perform the design, development and installation of these twenty units. Solar Power's experiences are described herein.

Description: The U.S. Coast Guard has developed a qualification test to screen photovoltaic modules for utilization on marine aids to navigation. The test is based on a combined-environment of hot and cold saltwater immersion and air pressurization. The test has demonstrated a very high acceleration factor and excellent correlation of electrical failures with modules in a concurrent real-time marine exposure.

Description: Design principles suggested here aim toward high conversion efficiency (greater than 15 percent) in polysilicon cells. The principles seek to decrease the liabilities of both intragranular and grain-boundary-surface defects. The advantages of a phosphorus atom concentration gradient in a thin (less than 50 microns) base of a p(+)/n(x)/n(+) drift-field solar cell, which produces favorable gradients in chemical potential, minority-carrier mobility and diffusivity, and recombination lifetime (via phosphorus gettering) are suggested. The degrading effects of grain boundaries are reduced by these three gradients and by substituting atoms (P, H, F or Li) for vacancies on the grain-boundary surface. From recent experiments comes support for the benefits of P diffusion down grain boundaries and, for quasi-grain-boundary-free and related structures. New analytic solutions for the n(x)-base include the effect of a power-law dependence between P concentration and lifetime. These provide an upper-bound estimate on the open circuit voltage. Finite-difference numerical solutions of the six Shockley equations furnish complete information about all solar-cell parameters and add insight concerning design.

Description: Major advances in photovoltaic (PV) Power Conditioning (PC) with respect to performance and low-cost potential have been made. Solutions have been obtained to interface and control problems related to adapting available inverter designs to the grid-connected, residential photovoltaic experiments. A description is presented to contributing research and development activities. Attention is given to aspects of residential systems experience, conceptual design studies, questions of optimum topology development, and promising advanced designs for residential PV provided by development efforts of the private sector.

Description: Mechanical fatigue of solar cell interconnects is a major failure mechanism in photovoltaic arrays. A comprehensive approach to the reliability design of interconnects, together with extensive design data for the fatigue properties of copper interconnects, has been published. This paper extends the previous work, developing failure prediction (fatigue) data for additional interconnect material choices, including aluminum and a variety of copper-Invar and copper-steel claddings. An improved global fatigue function is used to model the probability-of-failure statistics of each material as a function of level and number of cycles of applied strain. Life-cycle economic analyses are used to evaluate the relative merits of each material choce. The copper-Invar clad composites demonstrate superior performance over pure copper. Aluminum results are disappointing.