ALBERT

Description: The test capabilities of the Stability Wind Tunnel of the Virginia Polytechnic Institute and State University are described, and calibrations for curved and rolling flow techniques are given. Oscillatory snaking tests to determine pure yawing derivatives are considered. Representative aerodynamic data obtained for a current fighter configuration using the curved and rolling flow techniques are presented. The application of dynamic derivatives obtained in such tests to the analysis of airplane motions in general, and to high angle of attack flight conditions in particular, is discussed.

Description: Background information and exercises are provided to: (1) establish or expand understanding of the concepts, methods, and terminology of computer processing of image producing data; (2) develop insight into the advantages of computer based image processing compared with the photointerpretation approach for processing, classifying, interpreting, and applying remote sensing data; (3) foster a broad perspective on the principal of the main techniques for image enhancement, pattern recognition, and thematic classification; (4) appreciate the pros and cons of batch and interactive modes of image analysis; (5) examine and evaluate some specific computer generated products for subscenes in Pennsylvania and New Jersey; and (6) interrelate these particular examples of output with more theoretical explanations of computer processing strategies and procedures.

Description: Isolated knobs that are erosional remnants of central volcanoes or of folded rocks occur in several areas of the Altiplano are visible on both optical and images. The optically visible streaks occur in the immediate lee of the knobs, whereas the radar visible streaks occur in the zone downwind between the knobs. Aerial reconnaissance and field studies showed that the optically visible streaks consist of a series of small ( 100 m wide) barchan and barchanoid dunes, intradune sand sheets, and sand hummocks (large shrub coppice dunes) up to 15 m across and 5 m high. On LANDSAT images these features are poorly resolved but combine to form a bright streak. On the radar image, this area also appears brighter than the zone of the radar dark streak; evidently, the dunes and hummocks serve as radar reflectors. The radar dark streak consists of a relatively flat, smooth sand sheet which lacks organized aerolian bedforms, other than occasional ripples. Wind velocity profiles show a greater U value in the optically bright streak zone than in the radar dark streak.

Description: The diversity of proposed origins for large Martian outflow channels results from the differing interpretations given to the landforms associated with the outflow channels. In an attempt to help limit the possible mechanisms of channel erosion, detailed studies of three of the channel features were done; the streamlined islands, longitudinal grooves and scour marks. This examination involved a comparison of the martian streamlined islands with various streamlined landforms on Earth including those found in the Channel Scabland in large rivers, glacial drumlins, and desert yardangs. The comparisons included statistical analyses of the landform lengths versus widths and positions of maximum width, and an examination of the degree of shape agreement with the geometric lemniscate which was in turn demonstrated to correspond closely with true airfoil shapes. The analyses showed that the shapes of the martian islands correspond closely to the streamlined islands in rivers and the Channel Scabland land. Drumlins show a much smaller correlation. Erosional rock islands formed by glaciers are very much different in shape.

Description: Two innovative thermodynamic power cycles are analytically examined for future engineering feasibility. The power cycles use a hydrogen-oxygen fuel cell for electrical energy production and use the thermal dissociation of water for regeneration of the hydrogen and oxygen. The TDS (thermal dissociation system) uses a thermal energy input at over 2000 K to thermally dissociate the water. The other cycle, the HTE (high temperature electrolyzer) system, dissociates the water using an electrolyzer operating at high temperature (1300 K) which receives its electrical energy from the fuel cell. The primary advantages of these cycles is that they are basically a no moving parts system, thus having the potential for long life and high reliability, and they have the potential for high thermal efficiency. Both cycles are shown to be classical heat engines with ideal efficiency close to Carnot cycle efficiency. The feasibility of constructing actual cycles is investigated by examining process irreversibilities and device efficiencies for the two types of cycles. The results show that while the processes and devices of the 2000 K TDS exceed current technology limits, the high temperature electrolyzer system appears to be a state-of-the-art technology development. The requirements for very high electrolyzer and fuel cell efficiencies are seen as determining the feasbility of the HTE system, and these high efficiency devices are currently being developed. It is concluded that a proof-of-concept HTE system experiment can and should be conducted.

Description: This report discusses and documents the design, development, and verification of a microcomputer-based solar cell math model for simulating the Space Station's solar array Initial Operational Capability (IOC) reference configuration. The array model is developed utilizing a linear solar cell dc math model requiring only five input parameters: short circuit current, open circuit voltage, maximum power voltage, maximum power current, and orbit inclination. The accuracy of this model is investigated using actual solar array on orbit electrical data derived from the Solar Array Flight Experiment/Dynamic Augmentation Experiment (SAFE/DAE), conducted during the STS-41D mission. This simulator provides real-time simulated performance data during the steady state portion of the Space Station orbit (i.e., array fully exposed to sunlight). Eclipse to sunlight transients and shadowing effects are not included in the analysis, but are discussed briefly. Integrating the Solar Array Simulator (SAS) into the Power Management and Distribution (PMAD) subsystem is also discussed.

Description: Multipolarized airborne Synthetic Aperture Radar (SAR) data were acquired over a largely agricultural test site near Macomb, Illinois, in conjunction with the Shuttle Imaging Radar (SIR-B) experiment in October 1984. The NASA/JPL L-band SAR operating at 1.225 GHz made a series of daily overflights with azimuth view angles both parallel and orthogonal to those of SIR-B. The SAR data was digitally recorded in the quadpolarization configuration. An extensive set of ground measurements were obtained throughout the test site and include biophysical and soil measurements of approximately 400 agricultural fields. Preliminary evaluation of some of the airborne SAR imagery indicates a great potential for crop discrimination and assessment of canopy condition. False color composites constructed from the combination of three linear polarizations (HH, VV, and HV) were found to be clearly superior to any single polarization for purposes of crop classification. In addition, an image constructed using the HH return to modulate intensity and the phase difference between HH and VV returns to modulate chroma indicates a clear capability for assessment of canopy height and/or biomass. In particular, corn fields heavily damaged by infestations of corn borer are readily distinguished from noninfested fields.

Description: Multipolarization Synthetic Aperture Radar (SAR) data from the NASA/JPL aircraft SAR were used in conjunction with LANDSAT Thematic Mapper (TM), Thermal Infrared Multispectral Scanner (TIMS), and Airborne Imaging Spectrometer (AIS) data as part of a three-year research program to evaluate the utility of remote sensing measurements for analysis of sedimentary basins. The purpose of this research effort is to construct stratigraphic columns, map variations in the lithology, geometry, and structure of sedimentary rocks in the Wind River/Bighorn Basin area, Wyoming, and to integrate remote sensing data with conventional rain models of basin formation and evolution.

Description: Several digital data processing techniques were evaluated in an effort to identify and map active/abandoned, partially reclaimed, and fully revegetated surface mine areas in the central portion of Logan County. The TM data were first subjected to various enhancement procedures, including a linear contrast stretch, principal components and canonical analysis transformations. At the same time, four general procedures were followed to produce six classifications as a means of comparing the techniques involved. Preliminary results show that various feature extraction/data reduction techniques provide classification results equal or superior to the more straightforward unsupervised clustering technique. Analyst interaction time for labelling clusters is reduced using the canonical analysis and principal components procedures, though the canonical technique has clearly produced better results to date.

Description: The design and operations of a low cost, high rate thermal cycling facility designed for LEO conditions is described. Thermal cycling facilities were constructed with various design criteria. Some were designed to duplicate as closely as possible the conditions a cell or module would encounter while in orbit about the Earth. A typical facility to perform this type of cycling was a large vacuum system with liquid nitrogen cooled walls. The cells were heated by an AMO spectrum solar simulator, then a shutter was closed allowing the cells to give up their heat to the cold walls. This system was good at duplicating the orbital conditions but was slow and very costly to operate. Other systems used a gas atmosphere and heated the cells with radiant heat and cooled the cells by moving them into close proximity to a cold plate. The systems greatly increased the cycle times. Other systems moved the heating and cooling atmosphere into and out of the test areas and achieved reasonable cycle rates. All these systems, however, are expensive to operate.

Description: The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

Description: The solar array for the San Marco D/L spacecraft is described and the performance of 4 GaAs solar cell panels are examined. In comparison to the typical Si solar cell panel for San Marco D/L, it is shown that each GaAs solar cell panel provides at least 23 percent more specific power at maximum output and 28 deg C. Also described here, are several measurements that will be made to evaluate the relative performance of Si and GaAs solar cell panels during the San Marco D/L flight.

Description: The results of heteroepitaxial growth of GaAs and GaAlAs directly on Si are presented, and applications to new cell structures are suggested. The novel feature is the elimination of a Ge lattice transition region. This feature not only reduces the cost of substrate preparation, but also makes possible the fabrication of high efficiency monolithic cascade structures. All films to be discussed were grown by organometallic chemical vapor deposition at atmospheric pressure. This process yielded reproducible, large-area films of GaAs, grown directly on Si, that are tightly adherent and smooth, and are characterized by a defect density of 5 x 10(6) power/sq cm. Preliminary studies indicate that GaAlAs can also be grown in this way. A number of promising applications are suggested. Certainly these substrates are ideal for low-weight GaAs space solar ells. For very high efficiency, the absence of Ge makes the technology attractive for GaAlAs/Si monolithic cascades, in which the Si substrates would first be provided with a suitable p/n junction. An evaluation of a three bandgap cascade consisting of appropriately designed GaAlAs/GaAs/Si layers is also presented.

Description: Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Description: A short circuit current (I sub sc) degradation model for gallium arsenide (GaAs) solar cells irradiated by protons from low energy to 100 MeV was developed. This model was found to be satisfactory in predicting the I sub sc degradation of GaAs cells, but not that of silicon (Si) cells. A modification to the aforementioned model that preserves the optical wavelength dependency in the photogeneration of minority carrier pairs was described herein. Spectral Si and GaAs response and I sub sc for the Si and GaAs solar cells were discussed, and also were presented in graph form. The overall predictability of the modified model was deemed to be satisfactory.

Description: Manufacturing technology for mass producing high efficiency GaAs solar cells is discussed. A progress using a high throughput MO-CVD reactor to produce high efficiency GaAs solar cells is discussed. Thickness and doping concentration uniformity of metal oxide chemical vapor deposition (MO-CVD) GaAs and AlGaAs layer growth are discussed. In addition, new tooling designs are given which increase the throughput of solar cell processing. To date, 2cm x 2cm AlGaAs/GaAs solar cells with efficiency up to 16.5% were produced. In order to meet throughput goals for mass producing GaAs solar cells, a large MO-CVD system (Cambridge Instrument Model MR-200) with a susceptor which was initially capable of processing 20 wafers (up to 75 mm diameter) during a single growth run was installed. In the MR-200, the sequencing of the gases and the heating power are controlled by a microprocessor-based programmable control console. Hence, operator errors can be reduced, leading to a more reproducible production sequence.

Description: A KC-135A aircraft equipped with wing tip winglets was flight tested to demonstrate and validate the potential performance gain of the winglet concept as predicted from analytical and wind tunnel data. Flight data were obtained at cruise conditions for Mach numbers of 0.70, 0.75, and 0.80 at a nominal altitude of 36,000 ft. and winglet configurations of 15 deg cant/-4 deg incidence, 0 deg cant/-4 deg incidence, and baseline. For the Mach numbers tested the data show that the addition of winglets did not affect the lifting characteristics of the wing. However, both winglet configurations showed a drag reduction over the baseline configuration, with the best winglet configuration being the 15 deg cant/-4 deg incidence configuration. This drag reduction due to winglets also increased with increasing lift coefficient. It was also shown that a small difference exists between the 15 deg cant/-4 deg incidence flight and wind tunnel predicted data. This difference was attributed to the pillowing of the winglet skins in flight which would decrease the winglet performance.

Description: A joint NASA/USAF program was conducted to accomplish the following objectives: (1) evaluate the benefits that could be achieved from the application of winglets to KC-135 aircraft; and (2) determine the ability of wind tunnel tests and analytical analysis to predict winglet characteristics. The program included wind-tunnel development of a test winglet configuration; analytical predictions of the changes to the aircraft resulting from the application of the test winglet; and finally, flight tests of the developed configuration. Pressure distribution, loads, stability and control, buffet, fuel mileage, and flutter data were obtained to fulfill the objectives of the program.

Description: A full-scale winglet flight test on a KC-135 airplane with an upper winglet was conducted. Data were taken at Mach numbers from 0.70 to 0.82 at altitudes from 34,000 feet to 39,000 feet at stabilized flight conditions for wing/winglet configurations of basic wing tip, 15/-4 deg, 15/-2 deg, and 0/-4 deg winglet cant/incidence. An analysis of selected pressure distribution and data showed that with the basic wing tip, the flight and wind tunnel wing pressure distribution data showed good agreement. With winglets installed, the effects on the wing pressure distribution were mainly near the tip. Also, the flight and wind tunnel winglet pressure distributions had some significant differences primarily due to the oilcanning in flight. However, in general, the agreement was good. For the winglet cant and incidence configuration presented, the incidence had the largest effect on the winglet pressure distributions. The incremental flight wing deflection data showed that the semispan wind tunnel model did a reasonable job of simulating the aeroelastic effects at the wing tip. The flight loads data showed good agreement with predictions at the design point and also substantiated the predicted structural penalty (load increase) of the 15 deg cant/-2 deg incidence winglet configuration.

Description: A joint NASA/U.S. industry program to test advanced technology airfoils in the Langley 0.3-meter Transonic Tunnel (TCT) was formulated under the Langley ACEE Project Office. The objectives include providing U.S. industry an opportunity to compare their most advanced airfoils to the latest NASA designs by means of high Reynolds number tests in the same facility. At the same time, industry would again experience in the design and construction of cryogenic test techniques. The status and details of the test program are presented. Typical aerodynamic results obtained, to date, are presented at chord Reynolds number up to 45 x 10(6) and are compared to results from other facilities and theory. Details of a joint agreement between NASA and the Deutsche Forschungs- und Versuchsantalt fur Luft- and Raumfahrt e.V. (DFVLR) for tests of two airfoils are also included. Results of these tests will be made available as soon as practical.

Description: Various coatings developed in the FRG (i.e., second-surface mirrors with interference filters with and without conductive layers, conductive layers on solar-cell covers, and selective absorber coatings) have been qualified by accelerated tests under simulated space environment conditions. Experiments with coatings and solar cells have shown, however, that the thermo-optical behavior can differ considerably when performed on the ground and in space because of the great difficulty in simulating the space environment realistically. The objective of this experiment is to qualify these coatings under realistic space environment conditions. In addition, the experiment will provide design criteria, techniques, and test methods to insure control of the combined space and spacecraft environment effects, such as contamination, electrical conductance, and optical degradation, on the coatings. Data to be measured include the temperature of the samples, the electrical resistance of the conductive layers of the samples, the short circuit current of the solar-cell modules, and the deposition of contaminants on the samples (using quartz crystal microbalances (QCM's)).

Description: The objective of this experiment is to evaluate the synergistic effects of the space environment on various solar-array materials, including solar cells, cover slips with various antireflectance coatings, adhesive, encapsulants, reflector materials, substrate strength materials, mast and harness materials, structural composites, and thermal control treatments. The experiment is passive and consists of an arrangement of material specimens mounted in a 3-in.-deep peripheral tray. The effects of the space environment on the specimens will be determined by comparison of preflight and postflight measurements of mechanical, electrical, and optical properties.

Description: A model that explains the flat-spot power loss phenomenon is presented. Evidence suggests that the effect is due to localized metallurgical interactions between the silicon substrate and the contact metallization. These reactions are shown to result in localized regions in which the P-N junction is destroyed and replaced with a metal semiconductor-like interface. The effects of thermal treatment, crystallographic orientation, junction depth, and metallization are shown along with a method of preventing the effect through the suppression of vacancy formation at the free surface of the contact metallization. Data indicating the effectiveness of a TiN diffusion barrier in preventing the effect are also given.

Description: Images characteristics of geographic regions other than the northeastern part of the United States are presented for interpretation. Pre- and post-eruption imagery of Mt. St. Helens volcano serves to demonstrate the advantages of thermal infrared sensing, and the potential for developing a timely, decision oriented thematic map to be used in solving drought-related problems in Upper Volta is examined to show the applicability of satellite remote sensing in all geographic areas.

Description: The 1980 eruptions of Mount St. Helens in southeast Washington resulted in a pronounced effect on the surface and ground water resources of the state. In response to the volcanic activity, the U.S. Geological Survey intensified statewide surface and ground water sampling programs to determine the nature and magnitude of the volcanic-induced variations. Streams to the east of Mount St. Helens received the major ash fallout. Chemical effects were best noted in smaller streams sampled 60 to 70 miles northeast of Mount St. Helens. The chemical variations observed were pronounced but short lived. Sulfate and chloride increases in anionic composition were prevalent immediately following the eruption; however, the original bicarbonate predominance was again attained within several days. Suspended iron and aluminum concentrations were similarly elevated during the period of greatest ash deposition (highest turbidity); however, the dissolved concentrations remained relatively constant. Depressions of pH were minor and short lived. Streams draining to the south, tributaries to the Columbia river, showed little observable changes in water chemistry. Streams draining to the west (Toutle river and its tributaries) were compositionally affected by the various volcanic activities. Chloride and sulfate anion percentage exceeded the bicarbonate percentage up to one month following the eruption period. Streams and lakes sampled in the immediate vicinity of Mount St. Helens, in addition to trace metals, contained organic compounds derived from decomposing wood buried in the debris deposits. This organic material may constitute a significant source of organic compounds to surface and ground water for some time to come.

Description: The benefits-to-cost ratio of satellite remote sensing, both as a substitute for conventional methods of monitoring and assessing resources, and as a supplement to these methods is examined using a model which analyzes the cost of aerial photography versus satellite scanner for producing and interpreting an image of the Earth's surface sized to LANDSAT dimensions. Examples of cost savings are tabulated for ground surveys, aerial photos, and LANDSAT. Possible additional benefits from LANDSAT D are assessed. The way in which satellites fit into more comprehensive models for resources management is discussed. It is shown that remote sensing is but one essential component in a complex system that aggregates technical. Socioeconomics, political, cultural, and other factors in the human decision process.

Description: Computer processing facilitates extraction of information from every pixel by executing a variety of functional operations, called processed algorithms, in general or specialized routines. The best results are obtained when data from more than one multispectral band are used together. Multivariate tatistical analysis, computer tape characteristics, processing modes, and a choice of systems (batch or interactive) are discussed. The major operations in computer processing elaborated include: preprocessing, enhancement, effects of rationing, and classification. Techniques for multisource data correlation are considered with emphasis on geobased systems.

Description: Learning objectives include: (1) developing an understanding of the implications of the term "near surface observations"; (2) associating the appearance of large ground features as seen in satellite imagery with their appearance as seen from the ground; (3) grasping criteria and procedures for selecting training sites on the ground for use in supervised classification; (4) running through an example of training site selection; (5) becoming familiar with several methods of accuracy assessment; (6) becoming aware of the approach and value of making supporting measurements of the spectral and physical properties of materials on the ground and from aircraft; (7) taking note of the different types of instruments used in making specific ground measurements; and (8) appreciating the rationale underlying laboratory and field studies on or near the Earth's surface for the purpose of developing new sensor systems.

Description: Learning objectives include: (1) developing a facility for applying conventional techniques of photointerpretation to small scale (satellite) imager; (2) promoting the ability to locate, identify, and interpret small natural and man made surface features in a LANDSAT image; (3) using supporting imagery, such as aerial and space photography, to conduct specific applications analyses; (4) learning to apply change detection techniques to recognize and explain transient and temporal events in individual or seasonal imagery; (5) producing photointerpretation maps that define major surface units, themes, or classes; (6) classifying or analyzing a scene for specific discipline applications in geology, agriculture, forestry, hyrology, coastal wetlands, and environmental pollution; and (7) evaluating both advantages and shortcomings in relying on the photointerpretive approach (rather than computer based analytical approach) for extracting information from LANDSAT data.

Description: Activities are provided for: (1) developing insight into the way in which the LANDSAT MSS produces multispectral data; (2) promoting understanding of what a "pixel" means in a LANDSAT image and the implications of the term "mixed pixel"; (3) explaining the concept of spectral signatures; (4) deriving a simple signature for a class or feature by analysis: of the four band images; (5) understanding the production of false color composites; (6) appreciating the use of color additive techniques; (7) preparing Diazo images; and (8) making quick visual identifications of major land cover types by their characteristic gray tones or colors in LANDSAT images.

Description: Learning objectives of the activities provided include: (1) reading the annotation of a LANDSAT image; (2) becoming acquainted with the characteristics of 1:1,000,000 scale transparencies and prints of MSS images; (3) noting the general information visible in LANDSAT photo products; (4) observing changes of appearance of any ground feature or class in the black and white images made from the four MSS bands and the characteristic color of each class in color composites; (5) determining the degree to which a LANDSAT image meets map accuracy standards and can be fitted to map projections; (6) assessing the effects of LANDSAT enlargements and scale changes and of the limitations of satellite resolution relative to aerial photos; (7) observing the influence of time of acquisition (season) on a scene; (8) getting a feel for image quality as dependent on processing and photoreproduction; (9) appreciating the characteristics of the RBV and thermal band imagery obtained from LANDSAT-3; and (10) becoming familiar with certain attributes of adjacent LANDSAT images which permit them to be joined in mosaics and to be viewed in stereo.

Description: The primary LANDSAT mission and the system requirements are summarized and pertinent parameters of the spacecraft, its orbit, and payload are tabulated. The history acquisition to entry into the archives for storage and product generation and dissemination is recounted. The LANDSAT D data handling plan is discussed showing requirements for both the MSS CCT and the thematic mapper CCT.

Description: The term remote sensing is defined as well as ideas such as class, pattern, feature, pattern recognition, feature extraction, and theme. The electromagnetic spectrum is examined especially those wavelength regions available to remote sensing. Relevant energy and wave propagation laws are discussed and the characteristics of emitted and reflected radiation and their detection are investigated. The identification of classes by their spectral signatures, the multispectral approach, and the principal types of sensors and platforms used in remote sensing are also considered.

Description: Operation of the microwave instrument as a two frequency scatterometer, a synthetic aperture radar, and a passive microwave radiometer is planned. Operation of the instrument in each of its three modes is discussed and the antenna system described.

Description: Airborne Imaging Spectrometer data from Mono Lake, California, were studied in order to establish spectral radiance of test areas under solar illumination. The objective is to provide a method of atmospheric correction for major absorbers from the spectrometer data themselves. Crucial to the analysis is radiometric calibration of the instrument. Good agreement is found between calculated and measured radiances for uniform surface targets (beaches), but simulations of atmospheric properties with LOWTRAN lead to unreasonably low values of atmospheric precipitable water. Absorptions from carbon dioxide are not detected in the AIS data, but are strongly present in the LOWTRAN model. The apparent low contrast of all atmospheric absorption bands leads to a study of contamination from overlapping spectral orders in the AIS data. The suspected contamination is shown unambiguously to be present beyond approximately 1500 nm and consists of an extra radiance term including atmospheric bands from the delta/2 wavelength interval. A rigorous removal of the unwanted spectral contamination does not seem possible for any data taken in the rock mode. Rough estimates for tree-mode observations might be pieced together is a suitable after-the-fact radiometric claibration of the instrument can be formulated.

Description: The Space Shuttle Challenger was observed spectroscopically in two passes over Maui during the Spacelab 2 mission. Through most of one of the passes strong bands centered at 1.52 and 1.69 microns, tentatively identified as OH bands, were detected. The average luminosity of the Shuttle in the 1.45 to 1.75 micron range was roughly equal to that of a star of magnitude +5.5. The luminosity was much lower during part of the pass. Spectra from 0.65 to 2.4 microns were obtained during the second pass. These showed that most of the nonthermal emission is in the 1.2 to 2.2 micron range as would be expected for vibrationally excited OH.

Description: Dynamic model verification is the process whereby an analytical model of a dynamic system is compared with experimental data, adjusted if necessary to bring it into agreement with the data, and then qualified for future use in predicting system response in a different dynamic environment. These are various ways to conduct model verification. The approach taken here employs Bayesian statistical parameter estimation. Unlike curve fitting, whose objective is to minimize the difference between some analytical function and a given quantity of test data (or curve), Bayesian estimation attempts also to minimize the difference between the parameter values of that funciton (the model) and their initial estimates, in a least squares sense. The objectives of dynamic model verification, therefore, are to produce a model which: (1) is in agreement with test data; (2) will assist in the interpretation of test data; (3) can be used to help verify a design; (4) will reliably predict performance; and (5) in the case of space structures, will facilitate dynamic control.

Description: Multidisciplinary analysis often requires optimization of nonlinear systems that are subject to constraints. Trajectory optimization is one example of this situation. The Program to Optimize Simulated Trajectories (POST) was used successfully for a number of problems. The purpose is to describe POST and a new optimization approach that has been incorporated into it. Typical uses of POST will also be illustrated. The projected-gradient approach to optimization is the preferred option in POST and is discussed. A new approach to optimization, the random-walk approach, is described, and results with the random-walk approach are presented.

Description: The Earth's atmosphere from 90 km to 200 km provides the last aerothermodynamics frontier. Present NASA programs which require but also can provide an understanding of the aerodynamics and aerothermodynamics of the free molecule and transition flows that exist at these altitudes are the Aeroassisted OTV, Entry Research Vehicle and the Tethered Satellite. Each of these programs provides a unique opportunity to do flight research in the rarefied upper atmosphere. However, the Tethered Satellite Program provides, because of its capability to obtain global, in-situ, steady state data, the greatest potential to: (1)define the performance of aerodynamic shapes as a function of environmental characteristics (free molecule, transition, slip flow regimes); (2)define the characteristics of the upper atmosphere and the global variability of properties such as composition temperature, pressure and density. Such data are required to accomplish the systematic development and verification of analytical prediction techniques required to support advance configuration designs.

Description: The airborne L-band synthetic aperture radar (SAR) collected multipolarization calibrated image data over an irrigated agricultural test site near Fresno, CA, on March 6, 1984. The conclusions of the study are as follows: (1) the effects of incidence angle on the measured backscattering coefficients could be removed by using a correction factor equal to the secant of the angle raised to the 1.4 power, (2) for this scene and time of year, the various polarization channels were highly correlated such that the use of more than one polarization added little to the ability of the radar to discriminate vegetation type or condition; the exception was barley which separated from vineyards only when a combination of like and cross polarization data were used (polarization was very useful for corn identification in fall crops), (3) an excellent separation between herbaceous vegetation (alfalfa, barley, and oats) or bare fields and trees in orchards existed in brightness was well correlated to alfalfa height or biomass, especially for the HH polarization combination, (5) vineyards exhibited a narrow range of brightnesses with no systematic effects of type or number of stakes nor of number of wires in the trellises nor of the size of the vines, (6) within the orchard classes, areal biomass characterized by basal area differences caused radar image brightness differences for small to medium trees but not for medium to large trees.

Description: Two uncalibrated synthetic aperture radar (SAR) scenes from Death Valley, California, and two uncalibrated scenes from Owens Valley, California, were used to test a technique to identify and separate the primary factors associated with multipolarized radar image sets. Unique to the technique is the concept that varied types of radar polarization signatures are a result of the interaction of a few physical factors (e.g., roughness, volume scattering, and dielectric constant). Thus, the varied signatures observed in an image reflect the interaction between these factors. The objectives are to first separate the interaction of factors directly influencing the measurement and to attempt to identify these factors. Interpretation of the SAR image sets proceeds by testing models that hypothesize the cause and effect relations between those factors directly affecting the radar measurement and those features of interest to the interpreter. The results of our analysis indicated two consistent endmember types over all four image scenes. These types are defined by a high flat polarized signature near a level of 255 DN and a low level flat signature near 0 DN for all polarizations. Four other endmember types were also isolated. The spatial distribution of these endmember types indicates possible correspondence to surface volume scattering and changes in surface dielectric. However, the shapes of these endmember types were different from scene to scene.

Description: Imaging radar backscatter in continuously forested areas contains information about the forest canopy; it also contains data about topography, landforms, and terrain texture. For purposes of radar image interpretation and geologic mapping researchers were interested in identifying and separating forest canopy effects from geologic or geomorphic effects on radar images. The objectives of this investigation was to evaluate forest canopy variables in multipolarization radar images under conditions where geologic and topographic variables are at a minimum. A subsidiary objective was to compare the discriminatory capabilities of the radar images with corresponding optical images of similar spatial resolution. It appears that the multipolarization images discriminate variation in tree density, but no evidence was found for discrimination between evergreen and deciduous forest types.

Description: While radar does not provide detailed begetation discrimination, it provide the means to separate areas of different moisture conditions. Thus, the use of LANDSAT Thematic Mapper (TM) in conjunction with the microwave data was attempted. If successful, information on shoreline cover, emergent wetland vegetation and extent, and submerged grassbeds would provide much needed data for planning and maintenance of wetlands. Originally, the goal was to determine the accuracy with which one could categorize various types of vegetation and land use within an inland wetland using LANDSAT TM data. First, a Level 1/2 supervised classification was performed. Following a more detailed ground trust survey, a Level 3 classification was done. Aircraft L-band radar data were received and the decision was made to merge the TM and L-band data and assess whether vegetation catagories within the wetland areas could be better defined. Preliminary results indicate vegetation delineation is improved for open agricultural areas and water, but other features are more confused.

Description: The NASA/JPL Synthetic Aperture Radar (SAR) was flown over a 20 x 110 km test site in the Texas High Plains regions north of Lubbock during February/March 1984. The effect of incidence angle was investigated by comparing the pixel values of the calibrated and uncalibrated images. Ten-pixel-wide transects along the entire azimuth were averaged in each of the two scenes, and plotted against the calculated incidence angle of the center of each range increment. It is evident from the graphs that both the magnitudes and patterns exhibited by the corresponding transect means of the two images are highly dissimilar. For each of the cross-poles, the uncalibrated image displayed very distinct and systematic positive trends through the entire range of incidence angles. The two like-poles, however, exhibited relatively constant returns. In the calibrated image, the cross-poles exhibited a constant return, while the like-poles demonstrated a strong negative trend across the range of look-angles, as might be expected.

Description: Analysis of regional and high resolution remote sensing data coupled with detailed field investigations indicates Neogene compressional deformation in the southwest Dominican Republic. Airborne synthetic aperture radar data and high resolution near infrared photography show folds in Tertiary sediments and possible thrust fault scarps implying NE to SW compression in the region. Large road cuts through the scarps allow study of otherwise poorly accessible, heavily vegetated karst terrain. Deformation increases toward scrap fronts where small bedding-plane thrust faults become more numerous. Analysis of mesoscopic faults with slickensides indicates compression oriented between N to S and E to W. The lowermost scarp has highly sheared fault breccia and undeformed frontal talus breccias implying it is the basal thrust into which the higher thrust faults sole. Thus, the scarps probably formed in a regional NE to SW compressional stress regime and are the toes of thrust sheets. Previous workers have suggested that these scarps are ancient shorelines. However, the gross morphology of the scarps differs substantially from well known erosional terraces on the north coast.

Description: The purpose is not to provide a detailed discussion of several wall interference experiments, but rather to use these experiments (recently accomplished in the Boeing Transonic Wind Tunnel (BTWT) to illustrate the problems associated with many of the measurements required by current wall interference assessment/correction (WIAC) procedures. The wall correction to lift is emphasized. It is shown that, because conventional tunnels and relatively small models continue to be used, the flow field or flow boundary measurements to be made impose severe requirements on the experiment itself. In some cases, existing instrumentation and test techniques may not be adequate to obtain the data accuracies needed.

Description: Based upon limited, initial observations of wall interference corrections obtained for one airfoil test, there is a need for assessing the upstream flow direction. If there is no direct measurement then a two-pass correction procedure similar to the one described here is required. Questions have arisen pertaining to the correct interpretation of the pressure coefficients measured on the slats of a slotted tunnel wall, the interpretation of just what the calculated equivalent body encompasses or should include, and what can or should be considered as quantitative criteria for data correctability. Further studies using this modified procedure will address these questions. Hopefully, a meaningful WIAC procedure can be validated for the airfoil tests in the 0.3-m TCT.

Description: A series of airfoils were tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT) at Reynolds numbers from 2 to 50 million. The 0.3-m TCT is equipped with Barnwell slots designed to minimize blockage due to the tunnel flow and ceiling. This design suggests that sidewall corrections for blockage is needed, and that a lifting airfoil produces a change in angle of attack. Sidewall correction methods were developed for subsonic and subsonic-transonic flow. Comparisons of theory with experimental data obtained in the 0.3-m TCT for two airfoils, the British NPL 9510 and the German R-4 are presented. The NPL 9510 was tested as part of the NASA/United Kingdom Joint Aeronautical Program and R-4 was tested as part f the DFVLR/NASA Advanced Airfoil Research Program. For the NPL 9510 airfoil, only those test points that one would anticipate being difficult to predict theoretically are presented.

Description: Representation of the flow around full-scale ships was sought in the subsonic wind tunnels in order to a Hain Reynolds numbers as high as possible. As part of the quest to attain the largest possible Reynolds number, large models with high blockage are used which result in significant wall interference effects. Some experiences with such a high blockage model tested in the NASA Ames 12-foot pressure wind tunnel are summarized. The main results of the experiment relating to wind tunnel wall interference effects are also presented.

Description: The various procedures referred to as wall interference assessment and correction procedures presume the existence of a surface distribution of data (usually static pressure) measured over a surface on or near the tunnel walls for each test point to be assessed. An alternative approach in which a reasonably sophisticated computer model of the test section flow would be fitted parametrically to a sparse set of measured data is presented. The measurements provides line distributions of static pressure near the center lines of the top, side and bottom walls. The development of a test section model incorporating explicit recognition of discrete slots of finite length with controlled flow reentry into the solid wall downstream portion of the tunnel is shown.

Description: The NASA large flexible solar array space shuttle flight experiment is described. The 32 x 4 m wing is deployed from the shuttle bay, and experiments in electrical output, multiple deployment, and structural dynamics are planned. Both 2 x 4 cm and 5.9 x 5.9 cm cell assemblies on the array blanket are evaluated. Safety/hazards provisions are described, including emergency jettison provisions. Ground testing and hardware fabrication are summarized.

Description: A development program to produce 5.9 x 5.9 cm space quality silicon solar cells with a cost goal of 30 $/W is described. Cell types investigated include wraparound dielectric, mechanical wraparound and conventional contact configurations with combinations of 2 or 10 ohm/cm resistivity, back surface reflectors and/or fields, and diffused or ion implanted junctions. A single step process to cut cell and cover glass simultaneously is being developed. Results for cell and array tests are given. Large solar arrays that might use cells of this type are discussed.

Description: Objectives and progress in both low concentration ratio (6 to 10) and high concentration ratio ( 100) array developments are summarized. Problems encountered include: thermal control, maldistribution of concentrated sunlight, current busing, and optical surface degradation. The potential advantages over planar arrays are an order of magnitude reduction in per unit cost of power plus increased immunity to radiation damage.

Description: In order to understand better the polygenetic evolution of landforms on the martian surface, field studies were conducted in and around the Kharga Depression, Egypt. The Kharga region, on the eastern edge of Egypt's Western Desert, was subject to erosion under mostly hyperarid climatic conditions, punctuated by brief pluvial episodes of lesser aridity, since early Pleistocene time. The region contains numerous landforms analogous to features on the martian surface: yardangs carved in layered surficial deposits and in bedrock, invasive dune trains, wind-modified channels and interfluves, and depressions bounded by steep scarps. Like many of the topographic depresions on Mars, the Kharga Depression was invaded by crescentic dunes. In Egypt, stratigraphic relations between dunes, yardangs, mass-wasting debris, and wind-eroded flash-flood deposits record shifts in the relative effectiveness of wind, water, and mass-wasting processes as a function of climate change.

Description: The design and structural properties of a low concentration ratio solar array are discussed. The assembled module consists of six interconnected containers which are compactly stowed in a volume of 3.24 m(3) for delivery to orbit by the shuttle. The containers deploy in accordian fashion into a rectangular area of 19.4 x 68 meters and can be attached to the user spacecraft along the longitudinal centerline of the end container housing. Five rotary incremental actuators requiring about 8 watts each will execute the 180-degree rotation at each joint. Deployable masts (three per side) are used to extend endcaps from the housing in both directions. Each direction is extended by three masts requiring about 780 watts for about 27 minutes. Concentrator elements are extended by the endcaps and are supported by cable systems that are connected between the housings and endcaps. These power generating elements contain reflector panels which concentrate light onto the solar panels consisting of an aluminum radiator with solar cells positioned within the element base formed by the reflectors. A flat wire harness collects the power output of individual elements for transfer to the module container housing harnesses.

Description: Airborne Imaging Spectrometer (AIS) data were collected 30 August 1985 from a desert shrub community in central Oregon. Spectra from artificial targets placed on the test site and from bare soil, big sagebrush (Artemesia tridentata wyomingensis), silver sagebrush (Artemesia cana bolander), and exposed volcanic rocks were studied. Spectral data from grating position 3 (tree mode) were selected from 25 ground positions for analysis by Principal Factor Analysis (PFA). In this grating position, as many as six factors were identified as significant in contributing to spectral structure. Channels 74 through 84 (tree mode) best characterized between-class differences. Other channels were identified as nondiscriminating and as associated with such errors as excessive atmospheric absorption and grating positin changes. The test site was relatively simple with the two species (A. tridentata and A. cana) representing nearly 95% of biomass and with only two mineral backgrounds, a montmorillonitic soil and volcanic rocks. If, as in this study, six factors of spectral structure can be extracted from a single grating position from data acquired over a simple vegetation community, then AIS data must be considered rich in information-gathering potential.

Description: Airborne Imaging Spectrometer (AIS) data were acquired over an area of freshwater wetlands in Central California on September 23, 1985. Plant samples were subsequently collected along the flight line with the goal of relating plant tissue chemistry to spectral reflectance in the near-infrared region. It was determined that a consistent relationship existed between spectral response and plant tissue chemistry. This was especially evident in the 1500 to 1700 nm region.

Description: Airborne Imaging Spectrometer (AIS) data were acquired in 1985 over the Bonanza Creek Experimental Forest, Alaska for the analysis of canopy characteristics including biochemistry. Concurrent with AIS overflights, foliage from fifteen coniferous and deciduous forest stands were analyzed for a variety of biochemical constituents including nitrogen, lignin, protein, and chlorophyll. Preliminary analysis of AIS spectra indicates that the wavelength region between 1450 to 1800 namometers (nm) displays distinct differences in spectral response for some of the forest stands. A flat field subtraction (forest stand spectra - flat field spectra) of the AIS spectra assisted in the interpretation of features of the spectra that are related to biology.

Description: Airborne Imaging Spectrometer (AIS) data were collected over the fossil hot spring deposit at Ivanhoe, Nevada in order to determine the surface distribution of NH4-bearing minerals. Laboratory studies show that NH4-bearing minerals have characteristic absorption features in the near-infrared (NIR). Ammonium-bearing feldspars and alunites were observed at the surface of Ivanhoe using a hand-held radiometer. However, first look analysis of the AIS images showed that the line was about 500 m east of its intended mark, and the vegetation cover was sufficiently dense to inhibit preliminary attempts at making relative reflectance images for detection of ammonium minerals.

Description: The Airborne Imaging Spectrometer (AIS) was flown over granitic, volcanic, and calc-silicate terrain around the Mary Kathleen Uranium Mine in Queensland, in a test of its mineralocial mapping capabilities. An analysis strategy and restoration and enhancement techniques were developed to process the 128 band AIS data. A preliminary analysis of one of three AIS flight lines shows that the data contains considerable spectral variation but that it is also contaminated by second-order leakage of radiation from the near-infrared region. This makes the recognition of expected spectral absorption shapes very difficult. The effect appears worst in terrains containing considerable vegetation. Techniques that try to predict this supplementary radiation coupled with the log residual analytical technique show that expected mineral absorption spectra can be derived. The techniques suggest that with additional refinement correction procedures, the Australian AIS data may be revised. Application of the log residual analysis method has proved very successful on the cuprite, Nevada data set, and for highlighting the alunite, linite, and SiOH mineralogy.

Description: The Singatse Range is composed of a series of 53 types of volcanic, plutonic, metamorphic, and sedimentary rocks. In addition the Jurassic plutonic rocks are also of economic interest for their copper mineralization which is contained in a porphyry dike swarm. The 1984 and 1985 flight results from the Airborne Imaging Spectrometer (AIS) instrument flown in the NASA/JPL C-130 aircraft are contrasted and compared. The 1984 data are less noisy than the 1985, in which many sets of vertical stripings from bad detectors can be seen. Significantly however, enough of the hydrothermal alteration patterns can be seen in each line at the mutual crossing points that one can say that the specific targets were detected in both year's flights. The spectra of both years are corrupted by the second-order effect from the grating, but 0-H bond absorption at essentially correct wavelengths for sericite and/or kaolinite can be seen.

Description: The surface mineralogy in and around Moses Rock diatreme, a kimberlite-bearing dike in SW Utah, was examined using internally calibrated Airborne Imaging Spectrometer (AIS) data. Distinct near-infrared absorption characteristics of clays, gypsum, and serpentine (a key marker for kinberlite concentration) allowed the surface units containing these components to be identified spatially and the relative abundance of each component measured. Within the dike itself, channels and dispersed components of kimberlite and blocks of country rocks were accurately determined.

Description: Analysis of Airborne Imaging Spectrometer (AIS) data acquired in Australia has revealed a number of operational problems. Horizontal striping in AIS imagery and spectral distortions due to order overlap were investigated. Horizontal striping, caused by grating position errors can be removed with little or no effect on spectral details. Order overlap remains a problem that seriously compromises identification of subtle mineral absorption features within AIS spectra. A spectrometric model of the AIS was developed to assist in identifying spurious spectral features, and will be used in efforts to restore the spectral integrity of the data.

Description: The purpose is to describe work that is being done to find theoretical models to describe radar backscatter from vegetation layers. The geometry of the problem is shown. The information that one would like to find through the application of the results of these models would include: the thickness of the layer; the absorption in the layer (i.e., density, moisture content, and biomass); the geometry of the scatterers (i.e., shape and orientation); how much of the received power is due to volume scattering only; and a way to enhance the ratio of scattering that has some interaction with the ground surface. The proposed ways to find this information are discussed.

Description: This study was conducted as a part of the research tasks under the Radar Land Cover Analysis Program. The Radar Land Cover Analysis objective is, through utilization of multisensor data, to gain a basic understanding of the measurements and data characteristics in the visible-IR-microwave regions of the electromagnetic spectrum associated with specific surface features and cover types. Since the results of analysis of data acquired by Shuttle Imaging Radar (SIR-A) and LANDSAT Thematic Mapper (TM) over the study area were reported (NSTL/ERL Report No. 228, December 1984), this study focused on the analysis and evaluation of the L-band multipolarization airborne SAR data acquired over a southeastern pine forest scene. The data acquisition mission was flown on September 8 and 9, 1983. The HH, HV polarizations and the VV, VH polarizations were used on the first and the second day, respectively. Due to instrumentation difficulties, the digital recorder recorded only the second day's data. Because of this, only the VV and VH polarization data were used in this analysis. However, the HH and HV polarization images were available for visual comparison. It appears that SAR digital numbers correlate with the index of green biomass.

Description: Wall interference is made predominant in tunnel models and by wall geometries to facilitate the study of slot flow. The viscous effects in slots are studied by two dimensional measurements of flow. Wall interference is assessed by measuring pressure distributions at two levels near the walls. Interference on lifting delta wings is calculated. Pressure distributions at inner boundaries show basis axisymetries between the pressure side and the suction side, pointing to the necessity of having wider slots on the pressure side.

Description: Classical methods for calculation of wall corrections which are not satisfactory for a number of flows of interest are discussed. To meet these objections, a number of methods were developed which use measurements of the low at or close to the tunnel walls as an outer boundary condition to define wall interference. The development, assessment and application of one such method is summarized.

Description: Measured field data as a boundary condition for calculating the interference flow field were applied. They are divided into two categories. In the first category, the field data must consist of distributions of a single velocity component, and an accurate estimate of the hypothetical free air contribution of the model to this component is required. The differences between measured values and estimated model contributions are attributed to wall interference and they establish the boundary condition. The associated field data measurements are simple, yet the necessary model representation generally is a serious drawback. The second category requires field data which consist of velocity vector distributions at the price of multicomponent measurements, but at the profit that no information at all is required about the model. In solid wall test sections, the price is reduced to virtually zero but the profit remains.

Description: A limited-zone ventilated wall panel was developed for a closed-wall icing tunnel which permitted correct simulation of transonic flow over model rotor airfoil sections with and without ice accretions. Candidate porous panels were tested in the Ohio State University 6- x 12-inch transonic airfoil tunnel and result in essentially interference-free flow, as evidenced by pressure distributions over a NACA 0012 airfoil for Mach numbers up to 0.75. Application to the NRC 12- x 12-inch icing tunnel showed a similar result, which allowed proper transonic flow simulation in that tunnel over its full speed range.

Description: The free-stream interference caused by the flow through the slotted walls of the test sections of transonic wind tunnels has continuously a problem in transonic tunnel testing. The adaptive-wall transonic tunnel is designed to actively control the near-wall boundary conditions by sucking or blowing through the wall. In order to make the adaptive-wall concept work, parameters for computational boundary conditions must be known. These parameters must be measured with sufficient accuracy to allow numerical convergence of the flow field computations and must be measured in an inviscid region away from the model that is placed inside the wind tunnel. The near-wall flow field was mapped in detail using a five-port cone probe that was traversed in a plane transverse to the free-stream flow. The initial experiments were made using a single slot and recent measurements used multiple slots, all with the tunnel empty. The projection of the flow field velocity vectors on the transverse plane revealed the presence of a vortex-like flow with vorticity in the free stream. The current research involves the measurement of the flow field above a multislotted system with segmented plenums behind it, in which the flow is controlled through several plenums simultaneously. This system would be used to control a three-dimensional flow field.

Description: A three-dimensional adaptive-wall wind tunnel experiment was conducted at Ames Research Center. This experiment demonstrated the effects of wall interference on the upwash distribution on an imaginary surface surrounding a lifting wing. This presentation demonstrates how the interference assessment procedure used in the adaptive-wall experiments to determine the wall adjustments can be used to separately assess lift- and blockage-induced wall interference in a passive-wall wind tunnel. The effects of lift interference on the upwash distribution and on the model lift coefficient are interpreted by a simple horseshoe vortex analysis.

Description: A wall interference correction method for closed rectangular test sections was developed which uses measured wall pressures. Measurements with circular discs for blockage and a rectangular wing as a lift generator in a square closed test section validate this method. These measurements are intended to be a basis of comparison for measurements in the same tunnel using ventilated (in these case, slotted) walls. Using the vortex lattice method and homogeneous boundary conditions, calculations were performed which show sufficiently high pressure levels at the walls for correction purposes in test sections with porous walls. In Gottingen, an adaptive test section (which is a deformable rubber tube of 800 mm diameter) was built and a computer program was developed which is able to find the necessary wall adaptation for interference-free measurements in a single step. To check the program prior to the first run, the vortex lattice method was used to calculate wall pressure distributions in the nonadapted test section as input data for the one-step method. Comparison of the pressure distribution in the adapted test section with free-flight data shows nearly perfect agreement. An extension of the computer program can be made to evaluate the remaining interference corrections.

Description: The following areas were addressed: interchangeable test sections in the 0.3-M Transonic Cryogenic Tunnel (TCT); typical airfoil installation; airfoil capability; advanced technology airfoil test (ATAT); effects of the Reynolds number on the normal force coefficient; effects of the Reynolds number on the drag coefficient; and comparison of experimental results with theory.

Description: A formula for the determination of equivalent model geometry with two variables measured at the interface is derived, based on two dimensional subsonic flow. This predicted model profile is a reasonable initial estimate for transonic flow as long as the sonic region does not reach the interface. A general formula is given in two forms. One is in terms of complex variable functions and the other is an integral equation. The complex-function formula has the advantage of using analytic expressions. The integral equation form requires a numerical solution after assuming the model geometry as a polynomial function. Examples are given to illustrate the application of the formulas.

Description: LANDSAT data acquired over an agricultural area along with ground enumeration of the same area are used to obtain crop acreage estimates which are better (as measured in terms of bias and variance) than can be obtained from either data source alone. Two basic approaches considered within the AgRISTARS program are a stratified crop acreage estimator and a regression estimator. A statement of the problem was mathematically formulated and some theorems were proved which relate to the variance of the two estimators. For a particular set of data, the regression and stratified estimators are compared in terms of certain easily computed parameters.

Description: The two body problem was analyzed with a specific drag model. The model treats drag as a force proportional to the vector velocity and inversely proportional to the distance to the center of attraction. The solution is expressed in terms of known functions and is of a simple and compact form. The time of flight is expressed as a quadrature in the true anomaly. The results are: (1) development of a vector differential equation which allows analysis of an infinite number of gravitational and drag models; and (2) obtaining the solution of a linear differential equation using the inverse method of laplace transforms.

Description: Sand bars and islands within braided rivers have characteristic rhomboid or diamond shapes, often becoming very complex in form as the density of islands increases. Similar forms are observed in the martian outflow channels where the islands occur in groups. This contrasts with the more isolated martian islands which have airfoil shapes, as do isolated streamlined islands in rivers and in the Channeled Scabland. These observations indicate that the bar and island forms are controlled by the density of the islands, with increasing island interaction and flow modification as the density increases. As a continuation of previous flume experiments on the shapes of isolated islands, a new series of experiments investigate the modifications produced by a progressive increase in island density, finally leading to a true braided system.

Description: Spectral characteristics of semi-arid shrub communities were examined using Airborne Imaging Spectrometer (AIS) data collected in the tree mode on 23 May 1985. Mesic sites with relatively high vegetation density and distinct zonation patterns exhibited greater spectral signature variations than sites with more xeric shrub communities. Spectral signature patterns were not directly related to vegetation density or physiognomy, although spatial maps derived from an 8-channel maximum likelihood classification were supported by photo-interpreted surface features. In AIS data, the principal detected effect of shrub vegetation on the alluvial fans is to lower reflectance across the spectrum. These results are similar to those reported during a period of minimal physiological activity in autumn, indicating that shadows cast by vegetation canopies are an important element of soil-vegetation interaction under conditions of relatively low canopy cover.

Description: Airborne Imaging Spectrometer (AIS) data were acquired for several vegetation types within the humid temperate eastern United States. The spectral region covered, 0.9 to 2.1 microns, was little used in vegetation studies. A preliminary analysis of spectral curves suggests that variations between vegetation spectra may be useful for discriminating plant communities. Calibration and normalization procedures must be refined to compensate for cloud cover, detector and other system noise, and possible second-order effects.

Description: Spectral reflectance properties of deciduous oak-hickory forests covering the eastern half of the Rolla Quadrangle were examined using Thematic Mapper (TM) data acquired in August and December, 1982 and Airborne Imaging Spectrometer (AIS) data acquired in August, 1985. For the TM data distinctly high relative reflectance values (greater than 0.3) in the near infrared (Band 4, 0.73 to 0.94 micrometers) correspond to regions characterized by xeric (dry) forests that overlie soils with low water retention capacities. These soils are derived primarily from rhyolites. More mesic forests characterized by lower TM band 4 relative reflectances are associated with soils of higher retention capacities derived predominately from non-cherty carbonates. The major factors affecting canopy reflectance appear to be the leaf area index (LAI) and leaf optical properties. The Suits canopy reflectance model predicts the relative reflectance values for the xeric canopies. The mesic canopy reflectance is less well matched and incorporation of canopy shadowing caused by the irregular nature of the mesic canopy may be necessary. Preliminary examination of high spectral resolution AIS data acquired in August of 1985 reveals no more information than found in the broad band TM data.

Description: Techniques using Munsell color transformations were developed for reducing 128 channels (or less) of Airborne Imaging Spectrometer (AIS) data to a single color-composite-image suitable for both visual interpretation and digital analysis. Using AIS data acquired in 1984 and 1985, limestone and dolomite roof pendants and sericite-illite and other clay minerals related to alteration were mapped in a quartz monzonite stock in the northern Grapevine Mountains of California and Nevada. Field studies and laboratory spectral measurements verify the mineralogical distributions mapped from the AIS data.

Description: Airborne Imaging Spectrometer (AIS) data, field and laboratory spectra and samples for X-ray diffraction analysis were collected in argillically altered Tertiary volcanic rocks in the Hot Creek Range, Nevada. From laboratory and field spectral measurements in the 2.0 to 2.4 micron range and using a spectroradiometer with a 4 nm sampling interval, the absorption band centers for kaolinite were loacted at 2.172 and 2.215 microns, for montmorillonite at 2.214 micron and for illite at 2.205. Based on these values and the criteria for resolution and separtion of spectral features, a spectral sampling interval of less than 4 nm is necessary to separate the clays. With an AIS spectral sampling interval of 9.3 nm, a spectral matching algorithm is more effective for separating kaolinite, montmorillonite, ad illite in Hot Creek Range than using the location of absorption minima alone.

Description: Airborne Imaging Spectrometer (AIS) data were collected over Virginia City, Nevada; an area of gold and silver mineralization with extensive surface exposures of altered volcanic rocks. The data were corrected for atmospheric effects by a flat-field method, and compared to library spectra of various alteration minerals using a spectral analysis program SPAM. Areas of strong clay alteration were identified on the AIS images that were mapped as kaolinitic, illitic, and sericitic alterations zones. Kaolinitic alteration is distinguishable in the 2.1 to 2.4 and 1.2 to 1.5 micrometer wavelength regions. Montmorillonite, illite, and sericite have absorption features similar to each other at 2.2 micrometer wavelength. Montnorillonite and illite also may be present in varying proportions within one Ground Instantaneous Field of View (GIFOV). In general AIS data is useful in identifying alteration zones that are associated with or lie above precious metal mineralization at Virginia City.

Description: Airborne Imaging Spectrometers (AIS) data collected in 1984 and 1985 showed pronounced striping in the vertical and horizontal directions. This striping reduced the signal to noise ratio so that features of the spectra of forest canopies were obscured or altered by noise. This noise was removed by application of a notch filter to the Fourier transform of the imagery in each waveband.

Description: Selective absorption of electromagnetic radiation by atmospheric gases and water vapor is an accepted fact in terrestrial remote sensing. Until recently, only a general knowledge of atmospheric effects was required for analysis of remote sensing data; however, with the advent of high spectral resolution imaging devices, detailed knowledge of atmospheric absorption bands has become increasingly important for accurate analysis. Detailed study of high spectral resolution aircraft data at the U.S. Geological Survey has disclosed narrow absorption features centered at approximately 2.17 and 2.20 micrometers not caused by surface mineralogy. Published atmospheric transmission spectra and atmospheric spectra derived using the LOWTRAN-5 computer model indicate that these absorption features are probably water vapor. Spectral modeling indicates that the effects of atmospheric absorption in this region are most pronounced in spectrally flat materials with only weak absorption bands. Without correction and detailed knowledge of the atmospheric effects, accurate mapping of surface mineralogy (particularly at low mineral concentrations) is not possible.

Description: The first field test of NASA's Global Positioning System (GPS) Geodetic Program took place in March of 1985. The principal objective of this test was the demonstration of the feasibility of the fiducial station approach to precise GPS-based geodesy and orbit determination. Other objectives included an assessment of the performance of the several GPS receiver types involved in these field tests and the testing of the GIPSY software for GPS data analysis. In this article, the GIPSY (GPS Inferred Positioning System) software system is described and baseline solutions are examined for consistency with independent measurements made using very long baseline interferometry.

Description: The production of high-resolution topographic maps derived from interferometric synthetic aperture radar observations of the Earth is reported. Topographic maps are typically determined from stereo-pair optical photographs. Vertical relief causes the same terrain to appear in a slightly different projection for differing look angles, and this shift in appearance is interpreted in terms of the height of the terrain. The radar interferometric approach is related to the stereo technique in that the terrain is viewed at two different angles; however, in this case, the angular separation of the antennas is extremely small, on the order of a milliradian or less, as compared to tens of degrees for the optical case. Thus, the geometrical distortion and subsequent rectification correction algorithms are much less severe in the reduction of interferometric data.

Description: Wall interference correction procedures seek to determine the required changes in certain flow or geometric parameters so that the difference between the flow properties at the model's surface in the tunnel and free air are minimized. A transonic and a linear correction procedure were developed for aircraft models. In addition to Mach number and angle of attack corrections, an estimate of the accuracy of the corrections is provided by the transonic correction procedure. Lift, pitching moment and pressure measurements near the tunnel walls are required. The efficiency and accuracy of the correction procedure are improved. Moreover, correction of both the wing and tail angles of attack is allowed. The procedure is valid for transonic as well as subcritical flows. However, for subcritical flows further approximations and simplifying assumptions are made, leading to a very simple and efficient correction procedure.

Description: A facet of a unified tunnel correction scheme which uses wall pressures to determine tunnel induced blockage and upwash is described. With this method, there is usually no need to use data concerning model forces or power settings to find the interference; it follows directly from the pressures and tunnel dimensions. However, highly inclined jets do not produce good pressure signatures and are highly three dimensional, so they must be treated differently. Flow modeling is also discussed.

Description: Wall corrections as a function of wall porosity in the transonic wall interference problem was assessed. Effective porosities primarily for the two dimensional case were established as follows: (1) comparison of experimental data for two geometrically similar models of different chord/height ratio, an overall value of wall porosity could be deduced; (2) theoretical development which allows for unequal porosity for the floor and ceiling and wall boundary pressure measurements, porosities for floor and ceiling could be deduced; (3) a scheme was developed which allowed unequal porosity of floor and ceiling and streamwise varying porosity. The boundary layer development along the perforated floor and ceiling under the influence of the model pressure field, variations in boundary layer thickness underlining the difficulties in deducing meaningful values of wall porosity were determined. Wall boundary pressure measurement, in combination with singularity modelling of the airfoil, was sufficient to yield required information on the wall interference flow without having to establish some value for wall porosity. The singularity modelling of the airfoil initially covered only lift and volume but was extended to include drag and pitching moment, and second order volume term. It is shown by asymptotic transonic small disturbance analysis, that the derived corrections to angle of attack and free stream Mach number are correct to the first order.

Description: The effort to develop classical methods to compute wall interference at transonic speeds is outlined. The two-dimensional theory and three-dimensional development are discussed. Also, some numerical application of the two-dimensional work are indicated. The basic advantages of the asymptotic theory are noted.

Description: A solution for the tunnel wall boundary layer effects for three-dimensional subsonic tunnels is presented. The model potentials are represented with simple singularities placed on the centerline of the tunnel and Laplace's equation in cylindrical coordinates is solved for either the conventional homogeneous slotted-wall boundary condition, the solid-wall viscous boundary condition, or a combination of them. The most pronounced wall boundary layer effect is on solid blockage for completely closed wind tunnels. Boundary layers on the wall reduce the blockage from the solid-wall, no-boundary-layer case in a manner similar to opening slots in a solid wall. Additionally, for solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, whereas the lift interference factor at the model station does not depend on the boundary layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Description: Three experiments suitable for wall interference assessment and evaluation of proposed correction methods are presented. The experiments are: (1) a series of airfoil tests using a newly designed transonic flow facility that employs side-wall boundary layer suction and upper- and lower-wall shaping; (2) tests on a swept airfoil section spanning a solid-wall wind tunnel with fixed contouring on all four walls; and (3) tests on a swept wing of aspect ratio 3 mounted in a solid-wall wind tunnel with fixed flat walls. Each of the experiments provides data on the airfoil sections as well as on the wind tunnel walls. All the experiments were performed in solid wall wind tunnels corrected for boundary layer displacement effects. Although the experiments were performed primarily to evaluate computer code performance, it is believed that they also provide information that can be used to evaluate methods for assessing and correcting wall interference effects.

Description: Sidewall boundary layer effects were investigated by applying partial upstream sidewall boundary layer removal in the Langley 0.3-m transonic cryogenic tunnel. Over the range of sidewall boundary layer displacement thickness of these tests the influence on pressure distribution was found to be small for subcritical conditions; however, for supercritical conditions the shock position was affected by the sidewall boundary layer. For these tests (with and without boundary layer remove) comparisons with predictions of the GRUMFOIL computer code indicated that Mach number corrections due to the sidewall boundary layer improve the agreement for both subcritical and supercritical conditions. The results also show that sidewall boundary layer removal reduces the magnitude of the sidewall correction; however, a suitable correction must still be made.

Description: A validation of a measured boundary condition technique was carried out to demonstrate the feasibility of a wall interference assessment/correction (WIAC) system. An experimental evaluation was also carried out to compare performances of various techniques, to define the number of necessary boundary measurements for accurate assessment/corrections and to define the envelope of test conditions for which accurate assessment/corrections are achieved. The relative merits of a WIAC system and an adaptive wall tunnel are compared. The measurement surface boundary data is performed with a system of two rotating pipes. These pipes sweep out a cylindrical measurement surface near the tunnel walls, approximately one inch from the wall at the closest point. The experimental model was specially designed and fabricated for the adaptive wall experiments. The model is a wing/tail/body configuration with swept lifting surface. The boundary data taken in Tunnel 1T with the rotating pipe system has been shown to offer several attractive features for WIAC code evaluation. Good spatial resolution of measurements is achieved and measurements are made upstream and downstream of the model. Also, two velocity components are determined.

Description: The research undertaken concerning the computation and/or reduction of wall interference follows two main axes: improvement of wall correction determinations, and use of adaptive flexible walls. The use of wall-measured data to compute interference effects is reliable when the model representation is assessed by signatures with known boundary conditions. When the computed interferences are not easily applicable to correcting the results (especially for gradients in two-dimensional cases), the flexible adaptive walls in operation in T2 are an efficient and assessed means of reducing the boundary effects to a negligible level, if the direction and speed of the flow are accurately measured on the boundary. The extension of the use of adaptive walls to three-dimensional cases may be attempted since the residual corrections are assumed to be small and are computable.

Description: Participants expressed more interest in GaAs cells than in Si cells. For silicon cells, the beginning of life efficiency is not a major problem but more research is needed in the end of life efficiency. The beginning of life efficiency of GaAs cells must be brought up to 20% at AMO. More proton damage tests must be conducted. Liquid phase epitaxy technology is current but chemical vapor deposition technology is more flexible. There are no obvious problems in limiting process yields. Technology transfer should occur when market demands are generated.

Description: Principles and design considerations of IR transparent solar arrays are discussed. Optimization of performance of flexible solar arrays was studied. Measured solar absorptance as low as alpha s = 0.59 was achieved which leads to a predicted BOL power density of 182.7 = W/square meters. Advanced array concepts, system level cascaded panels, and transparent rigid panels are proposed and expected benefits discussed.

Description: A number of structurally efficient configurations for wing-type solar arrays are developed by a combination of deepening the planform of the blanket and structure and by partitioning the blanket with battens and frequent attachments to the support structure. This technique reduces the tension required to avoid a low natural frequency for the blanket, and the load reduction results in a lighter structure. The use of three different structures are investigated: the Astromast, the Extendible Support Structure (ESS), and a new beam called the STACBEAM (Stacking Triangular Articulated Compact Beam) and their relative performances are compared. The investigation of the STACBEAM is emphasized because its sequential deployment is more reliable for very long systems, and its linear deployment facilitates local attachments to the blanket and the development of a low mass deployer.

Description: Structurally efficient ways to support the large solar arrays (3,716 square meters which are currently considered for space station use) are examined. An erectable truss concept is presented for the on orbit construction of winged solar arrays. The means for future growth, maintenance, and repair are integrally designed into this concept. Results from parametric studies, which highlight the physical and structural differences between various configuration options are presented. Consideration is given to both solar blanket and hard panel arrays.