ALBERT

Description: Gas data of the Los Azufres geothermal field were analyzed using a method based on equilibrium of the Fischer- Tropsch (FT) reaction: CH4 + 2H2O = 4H2 +CO2 and on the combined pyrite-hematite-magnetite (HSH2) reactions: 5/4 H2 +3/2 FeS2 +3/4 Fe2O3 + 7/4 H2O = 3 H2S +Fe3O4 in order to estimate reservoir temperature and excess steam. The solution of equilibrium equations produces a grid (FT-HSH2). This method is suitable for reservoirs with relatively high H2S but low H2 and NH3 concentrations in the fluid as is the case of the Los Azufres well discharges. Reservoir temperature and reservoir excess steam values were estimated for initial and present conditions in representative wells of the field to study the evolution of fluids, because of exploitation and waste fluids reinjection. This method was very useful in estimating reservoir temperatures in vapor wells, while in two-phase wells it was found that as the well produces a smaller fraction of water, the reservoir temperature estimation agrees qualitatively with results from cationic or silica geothermometers. For liquid-dominated wells the reservoir temperature estimations agree with temperatures obtained from the well simulator WELFLO. This indicates that FT-HSH2 results provide the temperature of the fluid entering the well where the last equilibrium occurs. Results show a decrease in reservoir temperatures in the southern zone of the field where intensive reinjection takes place. With exploitation, it was also noted that the deep liquid phase in the reservoir is changing to two-phase increasing the reservoir steam fraction and the non-condensable gases in well discharges.

Description: Published

Description: JCR Journal

Description: open

Description: This special issue is dedicated to Yuri Taran's outstanding contributions to gas geochemistry that began in the early 1980s with his work on deuterium and 18O compositions of geothermal waters in the Mutnovsky (Kamchatka) region and continues to this day with work on the Kamchatka volcanic volatile budget, carbon isotopes of hydrocarbons, and new insights into the geochemistry of El Chichón volcano, Chiapas. Yuri has contributed greatly to the field of volcanic gas geochemistry and was the first to recognize the distinct deuterium and oxygen isotopic composition of fumarole condensates from volcanoes in Kamchatka (Taran et al. 1987a). The shift in δD and δ18O to significantly heavier values compared to local meteoric water led Yuri to introduce the term “andesitic water” (Taran et al. 1989a, b) which has since been recognized at subduction zone volcanoes globally. This distinct isotopic composition is evidence that volcanoes release water that ultimately originates as subducted seawater and is recycled through the mantle wedge back to the earth's surface. Yuri's early work on the gas emissions from Kamchatka and Kurile Islands volcanoes also included the development and testing of gas geothermometers (Taran 1986) and investigating hydrothermal alteration using isotopic data (Taran et al. 1987b). His curiosity remained focused on the isotope systematics of volcanic gases discharging from Kamchatka and the Kuriles through the late 1980s and 1990s with publications on the gas compositions of Klyuchevskoi (Taran et al. 1991), Mutnovsky (Taran et al. 1992), Avachinsky and Koryaksky (Taran et al. 1997). Yuri was involved in the discovery of a pure and unique rhenium mineral on Kudryavy volcano (Korzhinsky et al. 1994) and provided one of the most detailed chemical studies of high temperature (up to 950°C) fumaroles to date of any volcano (Taran et al. 1995). His 1995 paper on Kudryavy remains highly cited and provides the highest quality volcanic gas data which also include trace elements from a subduction zone. Such data are crucial when we attempt to interpret lower temperature volcanic gas compositions or calculate rare metal fluxes from volcanoes worldwide. His most recent publication on Kamchatka-Kurile volcanic emissions provides a detailed analysis of the total gas flux from these volcanoes (Taran 2009).

Description: Published

Description: 369-371

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: In questo lavoro si presentano i risultati di uno studio sulle caratteristiche del rumore sismico in prossimità del rilevatore di onde gravitazionali VIRGO (Cascina, Pisa), con particolare riferimento alle vibrazioni associate all’azione di un vicino parco eolico. La valutazione delle componenti spettrali del rumore verosimilmente indotte dagli aerogeneratori è stata effettuata mediante (i) Misure dirette alla base di una turbina, (ii) Correlazione fra le ampiezze spettrali del rumore e la velocità del vento; (iii) Determinazione delle proprietà direzionali da misure multicanale, (iv) Misura dell’attenuazione del segnale con la distanza dal parco eolico. Il disturbo provocato dagli aerogeneratori è particolarmente energetico alla frequenza di 1.7 Hz e, in particolari condizioni, è stato osservato fino a distanze di 11 km dal Parco Eolico. Il decadimento spaziale delle ampiezze ha un andamento complesso, che può essere interpretato in termini di una combinazione fra onde superficiali e onde di volume rifratte ad un’interfaccia profonda (~800 m) fra i sedimenti plio-pleistocenici ed i calcari Miocenici. La risposta locale nei dintorni dell’interferometro è stata investigata utilizzando la tecnica dei rapporti spettrali H/V. Si sono così evidenziate due bande di amplificazione imputabili ad effetti di risonanza legati alla geologia a scala locale: il primo intorno alla frequenza di 0.35 Hz, il secondo fra 0.7 e 2.0 Hz. Entrambi i picchi risultano essere essenzialmente omogenei in tutta l’area di studio, a conferma della sostanziale uniformità della struttura geologica.

Description: Published

Description: 1-30

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: Questo lavoro presenta una utility per il GIS MapInfo™ sviluppata per l'archiviazione ed elaborazione dei dati macrosismici dalla fase di georeferenziazione fino al plottaggio finale su mappa. L'identificazione della località associata con un'osservazione macrosismica è un'operazione che talvolta può causare errori ed in seguito problemi nell'analisi ed interpretazione dei dati. La routine MacroMap fornisce uno strumento che in modo semplice e veloce aiuti nell'identificazione della corretta località a cui attribuire l'informazione macrosismica durante lo studio di un terremoto. L'utility è strutturata per utilizzare il formato della directory geografica DIR04 e le procedure adottate nella compilazione del DataBase Macrosismico Italiano DBMI04. MacroMap è stata sperimentata "sul campo" durante alcune indagini macrosismiche e tiene conto dell'esperienza e dei suggerimenti degli operatori del Gruppo QUEST (QUick Earthquake Survey Team). I campi di utilizzo di MacroMap vanno dalla realizzazione speditiva di mappe e tabelle per la produzione di report macrosismici per la Protezione Civile, alla revisione di terremoti storici, grazie all'avanzato sistema di query disponibile per la selezione dei toponimi del database geografico.

Description: Published

Description: 1-21

Description: 5.1. TTC - Banche dati e metodi macrosismici

Description: N/A or not JCR

Description: open

Description: One of the main objectives of the ITACA (ITalian ACcelerometric Archive) strong motion database, promoted by the Italian Department of Civil Protection, was to improve the characterization of the recording sites from a geological and geophysical point of view and to provide their seismic classification according to the seismic norms pertinent to Italy, namely the Eurocode 8 and the National Technical Norms for Constructions. A standard format to summarize the available information for the recording stations was first produced, in terms of a technical report dynamically linked to the database, i.e., some of the relevant information is automatically updated when the corresponding fields of the database are modified. Then, an important activity of collection, qualification and synthesis of available data was carried out, especially for stations that recorded the strongest earthquakes in Italy in the last 40 years, and for which a relevant number of studies have been published. In spite of this activity, among the more than 700 strong motion stations present in the ITACA database, only a limited number of them could be characterized by quantitative information on subsurface soil properties. For this reason, a dual seismic site classification criterion was implemented, either based on the standard Vs,30 scheme, or, in the absence of such information, based on an expert opinion supported by shallow geology maps, mostly at 1:100,000 scale, and when available on the H/V ratios calculated on recordings. Owing to the relevance in the Italian geographic and morphological context, a special care was also given to the topographic classification of stations, based on suitable criteria developed within a GIS environment.

Description: Published

Description: 1779-1796

Description: 4.1. Metodologie sismologiche per l'ingegneria sismica

Description: JCR Journal

Description: open

Description: The Amik Basin is an asymmetrical composite transtensional basin developed between the seismically active left-lateral Dead Sea Fault (DSF) splays and the left-lateral oblique-slip Karasu Fault segment during neotectonic period. The relationship between the DSF and the East Anatolian Fault Zone is important as it represents a triple junction between Arabian Plate, African Plate and Anatolian Block in which the Amik Basin developed. The basin was formed on a pre-Miocene basement consisting of two rock series: Paleozoic crustal units with a Mesozoic allochthonous ophiolitic complex and ~1300 m thick Upper Miocene-Lower Pliocene sedimentary sequence. Plio-Quaternary sediments and Quaternary volcanics unconformably overlie the deformed and folded Miocene beds. Quaternary alkali-basaltic volcanism, derived from a metasomatized asthenospheric or lithospheric mantle, is most probably related to the syn-collisional transtensional strike-slip deformation in the area. Active faults in the region have the potential to generate catastrophic earthquakes (M〉7). Nineteen samples of cold and thermal groundwaters have been collected over the Amik Basin area for dissolved gas analyses as well as two samples from the gas seeps, and one bubbling gas from a thermal spring Samples were analysed for their chemical and isotopic (He, C) composition. On the basis of their chemical composition, three main groups can be recognized. Most of the dissolved gases (16; Group I) collected from springs or shallow wells (〈 150 m depth), contain mainly atmospheric gasses with very limited H2 (〈 80 ppm) and CH4 (1– 2700 ppm) contents and minor concentrations of CO2 (0.5–11.2 %). The isotopic composition of Total Dissolved Carbon evidences a prevailing organic contribution with possible dissolution of carbonate rocks. However the CO2-richest sample shows a small but significant deep (probably mantle) contribution which is also evidenced by its He isotopic composition. Further three samples, taken from the northern part of the basin close to Quaternary volcanic outcrops and main tectonic structures, also exhibit a small mantle He contribution (Fig. 1). The two dissolved gases (Group II) collected from deep boreholes (〉 1200 m depth) are typical of hydrocarbon reservoirs being very rich in CH4 (〉 78 %) and N2 (〉 13%). The water composition of these samples is also distinctive of saline connate waters (Cl- and B-rich, SO4-poor). Isotopic composition of methane (δ13C ~ -65‰) indicates a biogenic origin while He-isotopic composition points to a prevailing crustal signature for one (R/Ra 0.16) of the sites and a small mantle contribution for the other (R/Ra 0.98) (Fig. 1). The three free gas samples (Group III), taken at two sites within the ophiolitic basement west of the basin, have the typical composition of gas generated by low temperature serpentinisation processes with high hydrogen (37–50 %) and methane (10–61 %) concentrations. While all three gases show an almost identical δD-H2 of ~ -750‰, two of them display an isotopic composition of methane (δ13C ~ -5‰; δD ~ -105‰) and a C1/[C2+C3] ratio (~100) typical of abiogenic hydrocarbons and a significant contribution of mantle-type helium (R/Ra: 1.33). The composition of these two gasses is comparable to that of the gasses issuing in similar geologic conditions (Chimera-Turkey, Zambales-Philippine and Oman ophiolites). The gas composition of the other site evidences a contribution of a crustal (thermogenic) component (δ13C-CH4 ~ -30‰; δD-CH4 ~ -325‰; C1/[C2+C3] ~ 3000). Such crustal contribution is also supported by higher N2 contents (40% instead of 2%) and lower He-isotopic composition (R/Ra 0.07) (Fig. 1). These first results highlight contributions of mantle-derived volatiles possibly drained towards shallow levels by the DSF and other parallel structures crossing the basin showing a tectonic control of the fluids circulating within the Basin .

Description: Published

Description: Patras, Greece

Description: 4.5. Studi sul degassamento naturale e sui gas petroliferi

Description: open

Description: Methane plays an important role in the Earth’s atmospheric chemistry and radiative balance being the most important greenhouse gas after carbon dioxide. It has recently been established that geogenic gases contribute significantly to the natural CH4 flux to the atmosphere (Etiope et al., 2008). Volcanic/geothermal areas contribute to this flux, being the site of widespread diffuse degassing of endogenous gases (Chiodini et al., 2005). In such an environment soils are a source rather than a sink for atmospheric CH4 (Cardellini et al., 2003; Castaldi and Tedesco, 2005; D’Alessandro et al., 2009; 2011; 2013). Due to the fact that methane soil flux measurements are laboratory intensive, very few data have been collected until now in these areas. Preliminary studies (Etiope et al., 2007) estimated a total CH4 emission from European geothermal and volcanic systems in the range 4-16 kt a-1. This estimate was obtained indirectly from CO2 or H2O output data and from CO2/CH4 or H2O/CH4 values measured in the main gaseous manifestations. Such methods, although acceptable to obtain order-of-magnitude estimates, completely disregard possible methanotrophic activity within the soil. At the global scale, microbial oxidation in soils contributes for about 3-9% to the total removal of methane from the atmosphere. But the importance of methanotrophic organisms is even larger because they oxidise the greatest part of the methane produced in the soil and in the subsoil before its emission to the atmosphere. Environmental conditions in the soils of volcanic/geothermal areas (i.e. low oxygen content, high temperature and proton activity, etc.) have been considered inadequate for methanotrophic microrganisms. But recently, it has been demonstrated that methanotrophic consumption in soils occurs also under such harsh conditions due to the presence of acidophilic and thermophilic Verrucomicrobia. These organisms were found in Italy at the Solfatara di Pozzuoli (Pol et al., 2007), in New Zealand at Hell’s Gate (Dunfield et al., 2007) and in Kamchatka, Russia (Islam et al., 2008). Both the Italian and the Hellenic territories are geodynamically very active with many active volcanic and geothermal areas. Here we report on methane flux measurements made at Pantelleria (Italy) and at Sousaki and Nisyros (Greece). The total methane output of these three systems is about 10, 19 and 1 t a-1, respectively (D’Alessandro et al., 2009; 2011; 2013). The total emissions obtained from methane flux measurements are up to one order of magnitude lower than those obtained through indirect estimations. Clues of methanotrophic activity within the soils of these areas can be found in the CH4/CO2 ratio of the flux measurements which is always lower than that of the respective fumarolic manifestations, indicating a loss of CH4 during the travel of the gases towards earth’s surface. Furthermore laboratory methane consumption experiments made on soils collected at Pantelleria and Sousaki revealed, for most samples, CH4 consumption rates up to 9.50 µg h-1 and 0.52 µg h-1 respectively for each gram of soil (dry weight). Only few soil samples displayed no methane consumption activity. Finally, microbiological and molecular investigations allowed us to identify the presence of methanotrophic bacteria belonging to the Verrucomicrobia and to the Alpha- and Gamma-Proteobacteria in the soils of the geothermal area of Favara Grande at Pantelleria. While the presence of the former was not unexpected due to the fact that they include acidophilic and thermophilic organisms that were previously found in other geothermal environments, the latter are generally considered not adapted to live in harsh geothermal environments. Their presence in the soils of Pantelleria could be explained by the fact that these soils do not have extremely low pH values (〉5). Indeed thermotollerant methanotrophic Gamma-proteobacteria, have been previously found in the sediments of thermal springs in Kamchatka (Kizilova et al., 2012). Such species could find their niches in the shallowest part of the soils of Favara Grande were the temperatures are not so high and they thrive on the abundant upraising hydrothermal methane.

Description: Published

Description: Patras, Greece

Description: 4.5. Studi sul degassamento naturale e sui gas petroliferi

Description: open

Description: Twenty-five lava fountains occurred on Mt. Etna from January 2011 to April 2012. In summer 2012 volcanic activity resumed in a milder form within the Bocca Nuova crater, before it came to an essential halt in August 2012. All these unrests offer rich material for testing automatic procedures of data processing and alert systems, running 24/7, in the context of volcano surveillance. We focus on the seismic background radiation – volcanic tremor – which plays a key role in the monitoring of Mt. Etna. Since 2006 a multistation alert system has been established in the INGV operative centre of Catania exploiting STA/LTA ratios. Besides, also the spectral characteristics of the signal, which change correspondingly to the type of volcanic activity, can be exploited for warning purposes. Here we apply Self Organizing Maps and Fuzzy Clustering which offer an efficient way to visualize signal characteristics and its development with time. All these techniques allow to identify early stages of eruptive events, and automatically flag a critical status before this becomes evident in conventional monitoring techniques. Changes of tremor characteristics are related to the position of the source of the signal. The location of the sources exploits the distribution of the amplitudes across the seismic network. The locations were extremely useful for warning, throughout both the flank eruption in 2008 as well as the 2011 lava fountains, during which a clear migration of tremor sources towards the eruptive centres could be noticed in advance. The location of the sources completes the picture of an imminent volcanic unrest, and corroborates early warnings flagged by the changes of signal characteristics. Real time data processing requires computational efficiency, robustness of the methods and stability of data acquisition. The amplitude based multi-station approach is not sensitive to the failure of single stations and therefore offers a good stability. The single station approach, exploiting unsupervised classification techniques, limits logistic efforts, as only one or few key stations are necessary. Both strategies have proven to be insensitive to disturbances (undesired transients like earthquakes, noise, short gaps in the continuous data flow). False alarms were not encountered so far. Stable data acquisition and processing come with a properly designed data storage solution. The reliability of data storage and its access is a critical issue. A cluster architecture has been realized for failover protection, including a Storage Area Network system, which allow easy data access following predefined user policies. We present concepts of the software architectures deployed at INGV Osservatorio Etneo in order to implement this tremor-based multi approach system. We envisage the integration of seismic data and those originating from other scientific fields (e. g., volcano imagery, geochemistry, deformation, gravity, magneto-telluric). This will facilitate cross-checking of evidences encountered from the single data streams, in particular allow their immediate verification with respect to ground truth.

Description: Published

Description: Nicolosi (Catania, Italy)

Description: 1.4. TTC - Sorveglianza sismologica delle aree vulcaniche attive

Description: 5.6. TTC - Attività di Sala Operativa

Description: open

Description: Measurement of effusion rate is a primary objective for studies that model lava flow and magma system dynamics, as well as for monitoring efforts during on-going eruptions. However, its exact definition remains a source of confusion, and problems occur when comparing volume flux values that are averaged over different time periods or spatial scales, or measured using different approaches. Thus our aims are to: (1) define effusion rate terminology; and (2) assess the various measurement methods and their results. We first distinguish between instantaneous effusion rate, and time-averaged discharge rate. Eruption rate is next defined as the total volume of lava emplaced since the beginning of the eruption divided by the time since the eruption began. The ultimate extension of this is mean output rate, this being the final volume of erupted lava divided by total eruption duration. Whether these values are total values, i.e. the flux feeding all flow units across the entire flow field, or local, i.e. the flux feeding a single active unit within a flow field across which many units are active, also needs to be specified. No approach is without its problems, and all can have large error (up to ∼50%). However, good agreement between diverse approaches shows that reliable estimates can be made if each approach is applied carefully and takes into account the caveats we detail here. There are three important factors to consider and state when measuring, giving or using an effusion rate. First, the time-period over which the value was averaged; second, whether the measurement applies to the entire active flow field, or a single lava flow within that field; and third, the measurement technique and its accompanying assumptions.

Description: Published

Description: 1-22

Description: 1.5. TTC - Sorveglianza dell'attività eruttiva dei vulcani

Description: JCR Journal

Description: reserved

Description: The modern digital seismic stations are provided with 24 bit A/D converters, high capacity recording systems and broad-band seismometers. Nevertheless, few tens year old seismic stations can be still able to give an useful contribution to seismic monitoring. Some out-of-date seismic stations, such as the Lennartz PCM 5800, are characterized by the data acquisition in trigger mode on magnetic tape, allowing a continuous recording time of about 90 minutes. We have checked the possibility to substitute the Uher tape recorder of the Lennartz PCM 5800 stations with modern digital recorder, in order to give a new life to these stations. Several type of digital recorders have been tried. According to the results of our trials, the Hi-MiniDisc (Hi-MD) recorder is resulted the most useful one. This apparatus records on 1GB magneto-optical disks with a continuous recording time up to about 8 hours. This time allows to record about 500 trigger windows of about 50-60 seconds on one disk, about 5 time the old magnetic tape. According with these results, the Lennartz PCM 5800 digital seismic stations can be useful during seismic experiments or as a support of the Permanent Seismic Networks at local and regional scale.

Description: Published

Description: 1-17

Description: 1.4. TTC - Sorveglianza sismologica delle aree vulcaniche attive

Description: N/A or not JCR

Description: open

Description: Six hundred and sixty-seven water samples were collected from public drinking water supplies in Sicily and analysed for electric conductivity and for their Cl-, Br- and F- contents. The samples were, as far as possible, collected evenly over the entire territory with an average sampling density of about one sample for every 7600 inhabitants. The contents of Cl- and Br-, ranging between 5.53 and 1302 mg/l and between 〈 0.025 and 4.76 mg/l respectively, correlated well with the electric conductivity, a parameter used as a proxy for water salinity. The highest values were found both along the NW and SE coasts, which we attributed to seawater contamination, and in the central part of Sicily, which we attributed to evaporitic rock dissolution. The fluoride concentrations ranged from 0.023 to 3.28 mg/l, while the highest values (only 3 exceeding the maximum admissible concentration of 1.5 mg/l) generally correlated either with the presence in the area of crystalline (volcanic or metamorphic) or evaporitic rocks or with contamination from hydrothermal activity. Apart from these limited cases of exceeding F- levels, the waters of public drinking water supplies in Sicily can be considered safe for human consumption for the analysed parameters. Some limited concern could arise from the intake of bromide-rich waters (about 3% exceeding 1 mg/l) because of the potential formation of dangerous disinfection by-products.

Description: Published

Description: 303-313

Description: 4.4. Scenari e mitigazione del rischio ambientale

Description: JCR Journal

Description: reserved

Description: A new method of macroseismic surveys, based on voluntary collaboration through the Internet, has been running at the Istituto Nazionale di Geofisica e Vulcanologia (INGV) since July 2007. The macroseismic questionnaire is addressed to a single non-specialist; reported effects are statistically analysed to extrapolate a probabilistic estimate of Mercalli Cancani Sieberg and European Macroseismic Scale intensities for that observer. Maps of macroseismic intensity are displayed online in almost real time and are continuously updated when new data are made available. For densely inhabited zones, we have received reports of felt effects for even very small events (M=2). Six earthquakes are presented here, showing the ability of the method to give fast and interesting results. The effects reported in questionnaires coming from three towns are carefully analysed and assigned intensities are compared with those derived from traditional macroseismic surveys, showing the reliability of our web-based method.

Description: Published

Description: 1.11. TTC - Osservazioni e monitoraggio macrosismico del territorio nazionale

Description: JCR Journal

Description: open

Description: Methane plays an important role in the Earth’s atmospheric chemistry and radiative balance being the second most important greenhouse gas after carbon dioxide. Methane is released to the atmosphere by a wide number of sources, both natural and anthropogenic, with the latter being twice as large as the former (IPCC, 2007). It has recently been established that significant amounts of geological methane, produced within the Earth’s crust, are currently released naturally into the atmosphere (Etiope, 2004). Active or recent volcanic/geothermal areas represent one of these sources of geological methane. But due to the fact that methane flux measurements are laboratory intensive, very few data have been collected until now and the contribution of this source has been generally indirectly estimated (Etiope et al., 2007). The Greek territory is geodynamically very active and has many volcanic and geothermal areas. Here we report on methane flux measurements made at two volcanic/geothermal systems along the South Aegean volcanic arc: Sousaki and Nisyros. The former is an extinct volcanic area of Plio-Pleistocene age hosting nowadays a low enthalpy geothermal field. The latter is a currently quiescent active volcanic system with strong fumarolic activity due to the presence of a high enthalpy geothermal system. Both systems have gas manifestations that emit significant amounts of hydrothermal methane and display important diffuse carbon dioxide emissions from the soils. New data on methane isotopic composition and higher hydrocarbon contents point to an abiogenic origin of the hydrothermal methane in the studied systems. Measured methane flux values range from –48 to 29,000 (38 sites) and from –20 to 1100 mg/mˆ2/d (35 sites) at Sousaki and Nisyros respectively. At Sousaki measurement sites covered almost all the degassing area and the diffuse methane output can be estimated in about 20 t/a from a surface of about 10,000 mˆ2. At Nisyros measurements covered the Stephanos and Kaminakia areas, which represent only a part of the entire degassing area. The two areas show very different methane degassing pattern with latter showing much higher flux values. Methane output can be estimated in about 0.25 t/a from an area of about 30,000 mˆ2 at Stephanos and about 1 t/a from an area of about 20,000 mˆ2 at Kaminakia. The total output from the entire geothermal system of Nisyros probably should not exceed 2 t/a.

Description: Published

Description: Vienna, Austria

Description: 4.5. Studi sul degassamento naturale e sui gas petroliferi

Description: open

Description: A biomonitoring survey, above tree line level, using two endemic species (Senecio aethnensis and Rumex aethnensis) was performed on Mt. Etna, in order to evaluate the dispersion and the impact of volcanic atmospheric emissions. Samples of leaves were collected in summer 2008 from 30 sites in the upper part of the volcano (1500- 3000 m a.s.l). Acid digestion of samples was carried out with a microwave oven, and 44 elements were analyzed by using plasma spectrometry (ICP-MS and ICP-OES). The highest concentrations of all investigated elements were found in the samples collected closest to the degassing craters, and in the downwind sector, confirming that the eastern flank of Mt. Etna is the most impacted by volcanic emissions. Leaves collected along two radial transects from the active vents on the eastern flank, highlight that the levels of metals decrease one or two orders of magnitude with increasing distance from the source. This variability is higher for volatile elements (As, Bi, Cd, Cs, Pb, Sb, Tl) than for more refractory elements (Al, Ba, Sc, Si, Sr, Th, U). The two different species of plants do not show significant differences in the bioaccumulation of most of the analyzed elements, except for lanthanides, which are systematically enriched in Rumex leaves. The high concentrations of many toxic elements in the leaves allow us to consider these plants as highly tolerant species to the volcanic emissions, and suitable for biomonitoring researches in the Mt. Etna area.

Description: Published

Description: Vienna, Austria

Description: 4.4. Scenari e mitigazione del rischio ambientale

Description: open

Description: One of the main objectives of the project “Development and application of remote sensing methods for the monitoring of active Italian volcanoes” is directed to an operational use of differential interferometry as a tool for volcano monitoring. A first step to achieve this goal is to test commercial software in order to evaluate the most suitable for the project purposes. For testing software, SAR images collected by ERS2 from May 98 to August 98, before and after the strong eruptive event occurred on 22 July 98 at Voragine crater of Etna, have been selected. The explosive event was classified sub-plinian producing a 12 km high eruptive column and lapilli fell on land as far as 70 km south-eastward along the dispersal axis. Pre, post and across event image pairs have been processed. In particular the pair 13 May 98-22 July 98, 22 July 98-26 August 98, 13 May 98-26 August 98 are used for testing respectively pre, post and across event. In first analysis, the fringes in the differential products show a positive elevation trend in the summit area of the volcano. In particular, an increased of about 1,5 fringes in the period pre-event, and a decrement of 1 fringe in the period post-event is observed. This result is agreement whit field of deformation expected in such kind of event, confirming that the interferometric processing tool used id suitable for the purpose of the project.

Description: Published

Description: 15-20

Description: open

Description: The inversion problem dealt with is the identification of the parameters of a magma-filled dike which causes observable changes in ground deformation data. It is supposed that ground deformation data are measured by using the SAR (Synthetic Aperture Radar) Interferometry technique. The inversion approach, which is carried out by a systematic search technique based on the Simulated Annealing (SA) optimization algorithm, guarantees a high degree of accuracy. The results given in the paper are supported by experiments carried out using an interactive software tool developed ad hoc, which allows both direct and inverse modeling of SAR interferometric data related to the opening of a crack at the beginning and throughout a volcanic activity episode.

Description: Published

Description: 30-35

Description: open

Description: This guide reports the description of the experimental apparata in use in the experimental petrology along with an accurate description of some applications of these instrumentations. After a brief introduction concerning what is the experimental petrology and what is used for, we provide a description of the starting materials used in this field of the Earth Sciences. Moreover, particular attention is focused on these apparata used all around the world. We, finally, introduce some examples of different studies conducted with the different experimental equipments. The aim of this guide is, then, to give information concerning the equipments and their potentiality.

Description: Published

Description: 1-20

Description: 2.3. TTC - Laboratori di chimica e fisica delle rocce

Description: N/A or not JCR

Description: open

Description: Volcanoes represent an important natural source of several trace elements to the atmosphere. For some species (e.g., As, Cd, Pb and Se) they may be the main natural source and thereby strongly influencing geochemical cycles from the local to the global scale. Mount Etna is one of the most actively degassing volcanoes in the world, and it is considered to be, on the long-term average, the major atmospheric point source of many environmental harmful compounds. Their emission occurs either through continuous passive degassing from open-conduit activity or through sporadic paroxysmal eruptive activity, in the form of gases, aerosols or particulate. To estimate the environmental impact of magma-derived trace metals and their depositions processes, rainwater and snow samples were collected at Mount Etna area. Five bulk collectors have been deployed at various altitudes on the upper flanks around the summit craters of the volcano; samples were collected every two week for a period of one year and analyzed for the main chemical-physical parameters (electric conductivity and pH) and for major and trace elements concentrations. Chemical analysis of rainwater clearly shows that the volcanic contribution is always prevailing in the sampling site closest to the summit crater (about 1.5 km). In the distal sites (5.5-10 km from the summit) and downwind of the summit craters, the volcanic contribution is also detectable but often overwhelmed by anthropogenic or other natural (seawater spray, geogenic dust) contributions. Volcanic contribution may derive from both dry and wet deposition of gases and aerosols from the volcanic plume, but sometimes also from leaching of freshly emitted volcanic ashes. In fact, in our background site (7.5 km in the upwind direction) volcanic contribution has been detected only following an ash deposition event. About 30 samples of fresh snow were collected in the upper part of the volcano, during the winters 2006 and 2007 to estimate deposition processes at high altitude during cold periods. Some of the samples were collected immediately after a major explosive event from the summit craters to understand the interaction between snow and fresh erupted ash. Sulphur, Chlorine and Fluorine, are the major elements that prevailingly characterize the volcanic contribution in atmospheric precipitation on Mount Etna, but high concentrations of many trace elements are also detected in the studied samples. In particular, bulk deposition samples display high concentration of Al, Fe, Ti, Cu, As, Rb, Pb, Tl, Cd, Cr, U and Ag, in the site most exposed to the volcanic emissions: median concentration values are about two orders of magnitude higher than those measured in our background site. Also in the snow samples the volcanic signature is clearly detectable and decreases with distance from the summit craters. Some of the analysed elements display very high enrichment values with respect to the average crust and, in the closest site to the summit craters, also deposition values higher than those measured in polluted urban or industrial sites.

Description: Published

Description: Vienna, Austria

Description: 4.5. Degassamento naturale

Description: open

Description: Hydrological and geochemical studies performed on Lake Specchio di Venere on Pantelleria island (Italy) indicate that this endorheic basin has been formed through upwelling of the water table, and that it is continuously fed by the thermal springs situated on its shores. The lake is periodically stratified both thermally and in salinity, albeit this stratification is rather unstable over time since meteorological events such as strong rain or wind can determine the mixing of its waters. Periodical analyses of the lake water chemistry show large variations of the salt content due to the yearly evaporation-rain dilution cycle. These processes are also responsible for the saline stratification during steady meteorological conditions. The mineralogical characterisation of the bottom sediments shows the almost exclusive presence of neoformation minerals, mainly carbonates, formed in response to the pH gradient between spring- (pH≈6) and lake-waters (pH≈9). Finally, the CO2 partial pressures in the lake water slightly exceeding the atmospheric one, are due to the large amounts of CO2 brought to the lake through the bubbling free gas phase of the thermal springs. Nevertheless the high pH value of the lake water, its small volume and its periodical mixing prevent dangerous built up of this gas.

Description: Published

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: JCR Journal

Description: reserved

Description: Improving the constraints on the atmospheric fate and depletion rates of acidic compounds persistently emitted by non-erupting (quiescent) volcanoes is important for quantitatively predicting the environmental impact of volcanic gas plumes. Here, we present new experimental data coupled with modelling studies to investigate the chemical processing of acidic volcanogenic species during tropospheric dispersion. Diffusive tube samplers were deployed at Mount Etna, a very active open-conduit basaltic volcano in eastern Sicily, and Vulcano Island, a closed-conduit quiescent volcano in the Aeolian Islands (northern Sicily). Sulphur dioxide (SO2), hydrogen sulphide (H2S), hydrogen chloride (HCl) and hydrogen fluoride (HF) concentrations in the volcanic plumes (typically several minutes to a few hours old) were repeatedly determined at distances from the summit vents ranging from 0.1 to ~10 km, and under different environmental conditions. At both volcanoes, acidic gas concentrations were found to decrease exponentially with distance from the summit vents (e.g., SO2 decreases from ~10,000 μg/m3 at 0.1 km from Etna’s vents down to ~7 _μg/m3 at ~10km distance), reflecting the atmospheric dilution of the plume within the acid gas-free background troposphere. Conversely, SO2/HCl, SO2/HF, and SO2/H2S ratios in the plume showed no systematic changes with plume aging, and fit source compositions within analytical error. Assuming that SO2 losses by reaction are small during short-range atmospheric transport within quiescent (ash-free) volcanic plumes, our observations suggest that, for these short transport distances, atmospheric reactions for H2S and halogens are also negligible. The one-dimensional model MISTRA was used to simulate quantitatively the evolution of halogen and sulphur compounds in the plume of Mt. Etna. Model predictions support the hypothesis of minor HCl chemical processing during plume transport, at least in cloud-free conditions. Larger variations in the modelled SO2/HCl ratios were predicted under cloudy conditions, due to heterogeneous chlorine cycling in the aerosol phase. The modelled evolution of the SO2/H2S ratios is found to be substantially dependent on whether or not the interactions of H2S with halogens are included in the model. In the former case, H2S is assumed to be oxidized in the atmosphere mainly by OH, which results in minor chemical loss for H2S during plume aging and produces a fair match between modelled and measured SO2/H2S ratios. In the latter case, fast oxidation of H2S by Cl leads to H2S chemical lifetimes in the early plume of a few seconds, and thus SO2 to H2S ratios that increase sharply during plume transport. This disagreement between modelled and observed plume compositions suggests that more in-detail kinetic investigations are required for a proper evaluation of H2S chemical processing in volcanic plumes.

Description: Published

Description: 1441-1450

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 4.5. Degassamento naturale

Description: JCR Journal

Description: open

Description: This study presents baseline data for future geochemical monitoring of the active Tacaná volcano–hydrothermal system (Mexico–Guatemala). Seven groups of thermal springs, related to a NW/SE-oriented fault scarp cutting the summit area (4,100m a.s.l.), discharge at the northwest foot of the volcano (1,500–2,000m a.s.l.); another one on the southern ends of Tacaná (La Calera). The near-neutral (pH from 5.8 to 6.9) thermal (T from 25.7°C to 63.0°C) HCO3–SO4 waters are thought to have formed by the absorption of a H2S/SO2–CO2-enriched steam into a Cl-rich geothermal aquifer, afterwards mixed by Na/HCO3-enriched meteoric waters originating from the higher elevations of the volcano as stated by the isotopic composition (δD and δ18O) of meteoric and spring waters. Boiling temperature fumaroles (89°C at~3,600m a.s.l. NW of the summit), formed after the May 1986 phreatic explosion, emit isotopically light vapour (δD and δ18O as low as −128 and −19.9‰, respectively) resulting from steam separation from the summit aquifer. Fumarolic as well as bubbling gases at five springs are CO2-dominated. The δ13CCO2 for all gases show typical magmatic values of −3.6 ± 1.3‰ vs V-PDB. The large range in 3He/4He ratios for bubbling, dissolved and fumarolic gases [from 1.3 to 6.9 atmospheric 3He/4He ratio (RA)] is ascribed to a different degree of near-surface boiling processes inside a heterogeneous aquifer at the contact between the volcanic edifice and the crystalline basement (4He source). Tacaná volcano offers a unique opportunity to give insight into shallow hydrothermal and deep magmatic processes affecting the CO2/3He ratio of gases: bubbling springs with lower gas/water ratios show higher 3He/4He ratios and consequently lower CO2/3He ratios (e.g. Zarco spring). Typical Central American CO2/3He and 3He/4He ratios are found for the fumarolic Agua Caliente and Zarco gases (3.1 ± 1.6 × 1010 and 6.0 ± 0.9 RA, respectively). The L/S (5.9 ± 0.5)and (L + S)/M ratios (9.2 ± 0.7) for the same gases are almost identical to the ones calculated for gases in El Salvador, suggesting an enhanced slab contribution as far as the northern extreme of the Central American Volcanic Arc,Tacana

Description: In press

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: Le metodologie di indagine geochimica applicate ad un’ampia porzione dell’Appennino meridionale, esteso dalla Calabria settentrionale ai Monti Nebrodi, nell’ambito del progetto INGV-DPC S2, hanno consentito di valutare le caratteristiche dei fluidi emessi in coincidenza di importanti lineamenti strutturali, permettendo di evidenziare le relazioni intercorrenti tra l’assetto tettonico e la genesi, la circolazione ed il comportamento dei fluidi circolanti. L’area di studio rappresenta la porzione più meridionale dell’Arco Calabro, il cui stile deformativo dominante dal Pleistocene medio all’attuale, è caratterizzato da una estensione ESE-WNW. Nella Sicilia nord-orientale, le faglie neotettoniche dislocano i livelli crostali più superficiali e si dispongono secondo direzioni preferenziali orientati circa NW-SE con meccanismi deformativi a componente trascorrente ed estensionale e N-S/NE-SO con meccanismi deformativi trascorrenti, a tratti con componente compressiva. Le strutture crostali radicate sono rappresentate dal sistema “Patti-Eolie”, che si connette a terra con il sistema “Tindari-Letojanni” e dal “sistema di Messina”. Il primo mostra, anche a livello sismologico, caratteri deformativi transtensivi; nel secondo sistema, caratterizzato da faglie a prevalente componente distensiva del rigetto la catena presenta un tasso di sollevamento recente non uniforme, con valori massimi lungo la costa messinese ionica e tassi minori lungo quella tirrenica. L’esistenza di fenomeni attivi di sollevamento regionale è dimostrato da alcune evidenze, come la presenza di argille marine quaternarie affioranti diverse centinaia di metri al di sopra del livello del mare nonché di piattaforme di abrasione tirreniane ben sviluppate ad una altitudine di circa 130 m. nei pressi di Taormina e sul versante calabrese dello stretto di Messina. La struttura tettonica più importante che interseca il sistema Ibleo-Maltese è costituito dal sistema di faglie di Messina, orientato NNE-NNW. Il terremoto di Messina del 1908 è stato attribuito ad una “faglia cieca” nell’area di Messina. Lungo le principali strutture tettoniche, sono presenti attività idrotermali e di degassamento note da tempi storici, che dal punto di vista geochimico mostrano caratteristiche molto diverse in funzione della loro ubicazione.

Description: Published

Description: Reggio Calabria

Description: 3.2. Tettonica attiva

Description: open

Description: Volcanic and geothermal areas are one of the major natural sources of H2S to the atmosphere. Its environmental impact is often the main cause of the opposition to the development of geothermal energy exploitation programs. In this paper we analyze the air concentrations and dispersion pattern of naturally emitted H2S at the geothermal area of Sousaki (Corinthia, Greece). Measurements, made with a network of passive samplers, evidence a rapid decrease of concentration values away from the emission points. The fact that the decrease is more pronounced in the summer with respect to the winter indicates that it is not only due to a dilution effect, but also to redox reactions favoured by higher temperatures and intense sunlight typical of the summer period.

Description: Published

Description: 1723-1728

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: JCR Journal

Description: reserved

Description: Questa nota presenta una sintesi delle attività svolte durante il rilievomacrosismico del terremoto avvenuto tra le province di Parma e Reggio Emilia il 23 dicembre 2008. La scossa di Ml 5.2 è stata localizzata a sud di Parma ed è stata avvertita in tutta l’Italia settentrionale e in gran parte della Liguria e della Toscana. Il presente rapporto illustra lemodalità di intervento del teamQUEST, relative al rilievo degli effetti e alla valutazione in intensità MCS in particolare per le località della zona epicentrale. L’ampia documentazione fotografica illustra alcuni dettagli delle tipologie di danneggiamento rilevate e consente di comprendere meglio le valutazioni dell’intensità macrosismica. This paper presents an overview of the activities performed during the macroseismic field survey of the earthquake that occurred in the Parma and Reggio Emilia region on December 23, 2008. The mainshock (Ml=5.2), was located south of the city of Parma and was resolutely felt through Northern Italy. The report here presented shows the procedures carried out by QUEST (Quick Earthquake Survey Team), concerning the survey. QUEST has been engaged in gathering the damage information and in assessing the macroseismic intensity, in particular about the epicentral area. A copious photo collection shows details of the observed damage nature and allows to better illustrate the intensity

Description: Published

Description: 1-41

Description: 5.1. TTC - Banche dati e metodi macrosismici

Description: N/A or not JCR

Description: open

Description: The use of a hand-held thermal camera during the 2002–2003 Stromboli effusive eruption proved essential in tracking the development of flow field structures and in measuring related eruption parameters, such as the number of active vents and flow lengths. The steep underlying slope on which the flow field was emplaced resulted in a characteristic flow field morphology. This comprised a proximal shield, where flow stacking and inflation caused piling up of lava on the relatively flat ground of the vent zone, that fed a medial–distal lava flow field. This zone was characterized by the formation of lava tubes and tumuli forming a complex network of tumuli and flows linked by tubes. Most of the flow field was emplaced on extremely steep slopes and this had two effects. It caused flows to slide, as well as flow, and flow fronts to fail frequently, persistent flow front crumbling resulted in the production of an extensive debris field. Channel-fed flows were also characterized by development of excavated debris levees in this zone (Calvari et al. 2005). Collapse of lava flow fronts and inflation of the upper proximal lava shield made volume calculation very difficult. Comparison of the final field volume with that expecta by integrating the lava effusion rates through time suggests a loss of ~70% erupted lava by flow front crumbling and accumulation as debris flows below sea level. Derived relationships between effusion rate, flow length, and number of active vents showed systematic and correlated variations with time where spreading of volume between numerous flows caused an otherwise good correlation between effusion rate, flow length to break down. Observations collected during this eruption are useful in helping to understand lava flow processes on steep slopes, as well as in interpreting old lava–debris sequences found in other steep-sided volcanoes subject to effusive activity.

Description: Published

Description: JCR Journal

Description: reserved

Description: Seismic networks are worldwide diffuse to monitor both volcanic and tectonic seismogenetic areas. Some differences, such the basement on which the seismometer is located and the environmental conditions, characterize the installation of seismic stations in volcanic and tectonic areas. Nevertheless, some basic principles are common. To obtain good quality seismic data is very important to realize a high grade installation of all the instruments equipping a seismic station. Several procedure must be taken into account to optimize the instrument setting up. Electronic noise may be minimize using proper connecting line and adequate grounding. Effective lightning protections are essential to save instruments from both surges and strikes. Good seismometer ground coupling improves the signal quality and the signal-to-noise ratio. These procedures have been carried out at the Osservatorio Vesuviano to improve the existing seismic network as well as the installation of the new stations. As a result of this action an improvement of both the signal-to-noise ratio and the network reliability has been obtained.

Description: Published

Description: 1-20

Description: 1.4. TTC - Sorveglianza sismologica delle aree vulcaniche attive

Description: open

Description: Fluorine is one of the many environmental harmful elements released by volcanic activity. The content of total, oxalate extractable and water extractable fluorine was determined in 96 topsoils of three active volcanic systems of southern Italy (Mt. Etna, Stromboli and Vulcano). Total fluorine content (FTOT) ranges from 112 to 7430 mg kg-1, F extracted with oxalate (FOX) ranges from 16 to 2320 mg kg-1 (2 – 93 % of FTOT) and F extracted with distilled water (FH2O) ranges from 1.7 to 159 mg kg-1 (0.2 – 40 % of FTOT). Fluorine in the sampled topsoils derives both from the weathering of volcanic rocks and ashes and from enhanced deposition due to volcanic gas emissions either from open-conduit passive degassing (Mt. Etna and Stromboli) or from a fumarolic field (Vulcano). Fluorine accumulation in the studied soils does generally not present particular environmental issues except for a few anomalous sites at Vulcano where measured contents could be dangerous both for vegetation and for grazing animals.

Description: Published

Description: 413-423

Description: 4.5. Degassamento naturale

Description: JCR Journal

Description: reserved

Description: On 27 February 2007, a new eruption occurred on Stromboli which lasted until 2 April. It was characterized by effusive activity on the Sciara del Fuoco and by a paroxysmal event (15 March). This crisis represented an opportunity for us to refine the model that had been developed previously (2002–2003 eruption) and to improve our understanding of the relationship between the magmatic dynamics of the volcano and the geochemical variations in the fluids. In particular, the evaluation of the dynamic equilibrium between the volatiles (CO2 and SO2) released from the magma and the corresponding fluids discharged from the summit area allowed us to evaluate the level of criticality of the volcanic activity. One of the major accomplishments of this study is a 4-year database of summit soil CO2 flux on the basis of which we define the thresholds (low–medium–high) for this parameter that are empirically based on the natural volcanological evolution of Stromboli. The SO2 fluxes of the degassing plume and the CO2 fluxes emitted from the soil at Pizzo Sopra la Fossa are also presented. It is noteworthy that geochemical signals of volcanic unrest have been clearly identified before, during and after the effusive activity. These signals were found almost simultaneously in the degassing plume (SO2 flux) and in soil degassing (CO2 flux) at the summit, although the two degassing processes are shown to be clearly different. The interpretation of the results will be useful for future volcanic surveillance at Stromboli.

Description: Published

Description: 443-456

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: In questo lavoro viene descritto il complesso sistema di acquisizione dati della RSM [vedi D’Alema et al., 2011 - in questo volume], costituita da 58 stazioni collegate in tempo reale e 13 stazioni dial-up. I dati delle stazioni in tempo reale sono acquisiti con il programma Seiscomp31; la detezione degli eventi sismici viene eseguita con il programma Earthworm ed infine l’analisi e l’interpretazione degli eventi viene effettuata attraverso il programma SacPicker di Daniele Spallarossa [vedi Spallarossa, 2011 - in questo volume]. La parte di rete dial-up è basata sul sistema Lennartz Mars882 ed è configurata in modo autonomo dalla rete in tempo reale. I dati delle due reti vengono successivamente uniti in un unico dataset ai fini di una interpretazione interattiva congiunta.

Description: Published

Description: 124-127

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: Da alcuni anni l’INGV e la Regione Marche collaborano nell’azione di monitoraggio sismico del territorio regionale. Nella sede di Ancona del CNT sono acquisiti in tempo reale i segnali sismici di circa 80 stazioni dell’Italia centro-orientale. Si è reso pertanto necessario sviluppare applicativi utili al controllo degli apparati che compongono il sistema di monitoraggio. In particolare, vengono controllati: 1) lo stato di funzionamento delle trasmissioni radio ed ethernet; 2) lo stato dell’alimentazione delle stazioni e il numero di satelliti ricevuti dagli apparati GPS; 3) la quantità di segnale sismico archiviato e i gaps del segnale continuo; 4) i livelli di rumore di fondo e la qualità del segnale sismico.

Description: Published

Description: 104-107

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: A Pilot Project for CO2 injection and storage was proposed for a gas storage area located at Cortemaggiore (Piacenza), in northern Italy. This project is conducted both to verify the injection techniques and to analyze the potentiality of CO2 as a cushion gas. Starting from 2004, a series of analysis has been conducted to verify suitability and feasibility of this operation. The injection phase will be preceded by a passive seismic monitoring in order to measure the background seismicity of the area. Seismic monitoring will be carried out during the 3 years of the injection phase and will continue also for a control period of 2 years, following the working phase. The Milano - Pavia Department of the Istituto Nazionale di Geofisica e Vulcanologia is in charge of the surface seismic monitoring. To study the background seismicity a microseismic network composed by 7 seismic stations has been realized. On February 2010, a first test phase has been conducted for 3 sites. The network was completed with 4 more stations on May 2010. All stations are composed by a 24-bit digital recorder (Lennartz M24/NET) with GPS time signal. The study area is characterized by a very high anthropic and industrial noise. In order to improve the quality of the seismic signals, 4 stations have been installed in a 100 m deep borehole. The seismic sensors (Lennartz LE-3D/BH for the borehole and LE-3Dlite MKI for the installation at the surface) have similar technical characteristics with 1 Hz free period, cutoff frequency at 80 Hz and dynamic range of 136 dB. In this first stage we analyzed the microseismic noise level and evaluated the detection capability of the network. Using the RMS measurements the borehole stations indicate a reduction on the noise by a factor of 2.5. A more detailed analysis, performed using the density function distribution of the power spectra, evidences a 10 dB gain for the borehole stations in the frequency band 1 - 10 Hz. Noise measurements have been used also to determine the minimum magnitude for the events detection. Using a point source model to simulate seismic events, we verified the expected detection levels by comparing the estimates obtained with the simulation and the local events recorded by the seismic network.

Description: Published

Description: 12

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: Nell’ambito del progetto FIRB-Airplane [“Piattaforma di ricerca multidisciplinare su terremoti e vulcani”, fondi MIUR 2007-2011 responsabili: Cocco, Amato e Stucchi1] dalla seconda metà del 2009 è stata installata una rete densa di stazioni sismiche nell’area dell’Alta Val Tiberina (AVT, Figura 1), i cui dati in continuo vengono trasmessi alla sede di Ancona del CNT attraverso una dorsale Wi-Fi HYPERLAN [Monachesi e Cattaneo, 2010]. La rete è stata progettata cercando di rispettare alcuni criteri, tra cui: controllo continuo della funzionalità delle singole stazioni, flessibilità nella scelta dei siti, riduzione del rischio di fulminazioni, possibilità di abbinare stazioni sismiche e stazioni geodetiche. A tal fine sono stati adottati strumenti a basso consumo per quel che riguarda acquisitori e sistemi di trasmissione, accompagnati dall’utilizzo di sistemi di alimentazione autonomi e sistemi di telecontrollo

Description: Published

Description: 91-93

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: Over fifty eruptive episodes with Strombolian activity, lava fountains, and lava flows occurred at Mt Etna volcano between 2006 and 2013. Namely, there were seven paroxysmal lava fountains at the South-East Crater in 2007-2008 and 46 at the New South-East Crater between 2011 and 2013. Lava emissions lasting months affected the upper eastern flank of the volcano in 2006 and 2008-2009. Effective monitoring and forecast of such volcanic phenomena are particularly relevant for their potential socio-economic impact in densely populated regions like Catania and its surroundings. For example, explosive activity has often formed thick ash clouds with widespread tephra fall able to disrupt the air traffic, as well as to cause severe problems at infrastructures, such as highways and roads. Timely information about changes in the state of the volcano and possible onset of dangerous eruptive phenomena requires efficacious surveillance methods. The analysis of the continuous background seismic signal, the so-called volcanic tremor, turned out of paramount importance to follow the evolution of volcanic activity [e.g., Alparone et al., 2003; Falsaperla et al., 2005]. Changes in the state of the volcano as well as in its eruptive style are usually concurrent with variations of the spectral characteristics (amplitude and frequency) of tremor. The huge amount of digital data continuously acquired by INGV’s broadband seismic stations every day makes a manual analysis difficult. In order to tackle this problem, techniques of automatic classification of the tremor signal are applied. In a comparative study, the robustness of different methods for the identification of regimes in volcanic activity were examined [Langer et al., 2009]. In particular, Langer et al. [2011] applied unsupervised classification techniques to the tremor data recorded at one station during seven paroxysmal episodes in 2007-2008. Their results revealed significant changes in the pattern classification well before the onset of the eruptive episodes. This evidence led to the development of specific software packages, such as the program KKAnalysis [Messina and Langer, 2011], a software that combines an unsupervised classification method (Kohonen Maps) with fuzzy cluster analysis. The operational characteristics of these tools - fail-safe, robustness with respect to noise and data outages, as well as computational efficiency - allowed on-line processing at the operative centre of the INGV-Osservatorio Etneo in 2010 and the identification of criteria for automatic alarm flagging. The system is hitherto one of the main automatic alerting tools to identify impending eruptive events at Etna. The software carries out the on-line processing of the new data stream coming from two seismic stations, merged with reference datasets of past eruptive episodes. In doing so, results obtained for new data are immediately compared to previous eruptive scenarios. Given the rich material collected in recent years, we are able to apply the alert system to eleven stations at different elevations (1200-3050 m) and distances (1-8 km) from the summit craters. Critical alert parameters were empirically defined to obtain an optimal tuning of the alert system for each station. To verify the robustness of this new, multistation alert system, a dataset encompassing about eight years of continuous seismic records (since 2006) was processed automatically using KKAnalysis and collateral software off-line. Then, we analyzed the performance of the classifier in terms of timing and spatial distribution of the stations. We also investigated the performance of the new alert system based on KKAnalysis in case of activation of whatever eruptive centre. Intriguing results were obtained in 2010 throughout periods characterized by the renewal of volcanic activity at Bocca Nuova-Voragine and North-East Crater, and in the absence of paroxysmal phenomena at South-East Crater and New South-East Crater. Despite the low-energy phenomena reported by volcanologists (i.e., degassing, low-to moderate explosions), the triggered alarms demonstrate the robustness of the classifier and its potential: i) to identify even subtle changes within the volcanic system using tremor, and ii) to highlight the activation of a single eruptive centre, even though different from the one for which the classifier was initially tested. It is worth noting that in case of activation of weak sources, the successful performance of the classifier depends upon the general level of signals originating from other sources in that specific time span.

Description: Published

Description: Nicolosi (Catania, Italy)

Description: 2V. Dinamiche di unrest e scenari pre-eruttivi

Description: open

Description: Active volcanoes characterized by open conduit conditions generate sonic and infrasonic signals, whose investigation provides useful information for both monitoring purposes and studying the dynamics of explosive processes. In this work, we discuss the automatic procedures implemented for a real-time application to the data acquired by a permanent network of five infrasound stations running at Mt. Etna volcano. The infrasound signals at Mt. Etna consist in amplitude transients, called infrasound events. The adopted procedure uses a multi-algorithm approach for event detection, counting, characterization and location. It is designed for an efficient and accurate processing of infrasound records provided by single-site and array stations. Moreover, the source mechanism of these events can be investigated off-line or in near real-time by using three different models: (1) Strombolian bubble; (2) resonating conduit and (3) Helmholtz resonator. The infrasound waveforms allow us to choose the most suitable model, to get quantitative information about the source and to follow the time evolution of the source parameters.

Description: Published

Description: 1215–1231

Description: 1.4. TTC - Sorveglianza sismologica delle aree vulcaniche attive

Description: JCR Journal

Description: reserved

Description: In the past, variations in the chemical contents (SO4 2−, Cl−, cations) of crater lake water have not systematically demonstrated any relationships with eruptive activity. Intensive parameters (i.e., concentrations, temperature, pH, salinity) should be converted into extensive parameters (i.e., fluxes, changes with time of mass and solutes), taking into account all the internal and external chemical–physical factors that affect the crater lake system. This study presents a generalized box model approach that can be useful for geochemical monitoring of active crater lakes, as highly dynamic natural systems. The mass budget of a lake is based on observations of physical variations over a certain period of time: lake volume (level, surface area), lake water temperature, meteorological precipitation, air humidity, wind velocity, input of spring water, and overflow of the lake. This first approach leads to quantification of the input and output fluxes that contribute to the actual crater lake volume. Estimating the input flux of the "volcanic" fluid (Qf - kg/s) –– an unmeasurable subsurface parameter –– and tracing its variations with time is the major focus during crater lake monitoring. Through expanding the mass budget into an isotope and chemical budget of the lake, the box model helps to qualitatively characterize the fluids involved. The (calculated) Cl− content and dD ratio of the rising "volcanic" fluid defines its origin. With reference to continuous monitoring of crater lakes, the present study provides tips that allow better calculation of Qf in the future. At present, this study offers the most comprehensive and up-to-date literature review on active crater lakes.

Description: Published

Description: 161-173

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: JCR Journal

Description: open

Description: Active volcanoes are thought to be important contributors to the atmospheric mercury (Hg) budget, and this chemical element is one of the most harmful atmospheric pollutants, owing to its high toxicity and long residence time in ecosystems. There is, however, considerable uncertainty over the magnitude of the global volcanic Hg flux, since the existing data on volcanogenic Hg emissions are sparse and often ambiguous. In an attempt to extend the currently limited dataset on volcanogenic Hg emissions, we summarize the results of Hg flux measurements at seven active open-conduit volcanoes; Stromboli, Asama, Miyakejima, Montserrat, Ambrym, Yasur, and Nyiragongo.. Data from the domebuilding Soufriere Hills volcano are also reported. Using our determined mercury to SO2 mass ratios in tandem with the simultaneously-determined SO2 emission rates, we estimate that the 7 volcanoes have Hg emission rates ranging from 0.2 to 18 t yr-1 (corresponding to a total Hg flux of ~41 t·yr-1). Based on our dataset and previous work, we propose that a Hg/SO2 plume ratio ~10-5 is bestrepresentative of gas emissions from quiescent degassing volcanoes. Using this ratio, we infer a global volcanic Hg flux from persistent degassing of ~95 t·yr-1

Description: Published

Description: 497-510

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: restricted

Description: During 2007–2008, three CO2 flux surveys were performed on El Chichón volcanic lake, Chiapas, Mexico, with an additional survey in April 2008 covering the entire crater floor (including the lake). The mean CO2 flux calculated by sequential Gaussian simulation from the lake was 1,190 (March 2007), 730 (December 2007) and 1,134 g m−2 day−1 (April 2008) with total emission rates of 164±9.5 (March 2007), 59±2.5 (December 2007) and 109±6.6 t day−1 (April 2008). The mean CO2 flux estimated from the entire crater floor area was 1,102 g m−2 day−1 for April 2008 with a total emission rate of 144±5.9 t day−1. Significant change in CO2 flux was not detected during the period of survey, and the mapping of the CO2 flux highlighted lineaments reflecting the main local and regional tectonic patterns. The 3He/4He ratio (as high as 8.1 RA) for gases in the El Chichón crater is generally higher than those observed at the neighbouring Transmexican Volcanic Belt and the Central American Volcanic Arc. The CO2/3He ratios for the high 3He/4He gases tend to have the MORB-like values (1.41×109), and the CO2/3He ratios for the lower 3He/4He gases fall within the range for the arc-type gases. The high 3He/4He ratios, the MORB-like CO2/3He ratios for the high 3He/4He gases and high proportion of MORB-CO2 (M=25 ±15%) at El Chichón indicate a greater depth for the generation of magma when compared to typical arc volcanoes.

Description: Published

Description: 423-441

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: A periodic sampling of the groundwaters and dissolved and free gases in selected deep wells located in the area affected by the May-June 2012 southern Po Valley seismic sequence has provided insight into seismogenic-induced changes of the local aquifer systems. The results obtained show progressive changes in the fluid geochemistry, allowing it to be established that deep-seated fluids were mobilized during the seismic sequence and reached surface layers along faults and fractures, which generated significant geochemical anomalies. The May-June 2012 seismic swarm (mainshock on May 29, 2012, M 5.8; 7 shocks M 〉5, about 200 events 3 〉 M 〉 5) induced several modifications in the circulating fluids. This study reports the preliminary results obtained for the geochemical features of the waters and gases collected over the epicentral area from boreholes drilled at different depths, thus intercepting water and gases with different origins and circulation. The aim of the investigations was to improve our knowledge of the fluids circulating over the seismic area (e.g. origin, provenance, interactions, mixing of different components, temporal changes). This was achieved by collecting samples from both shallow and deep-drilled boreholes, and then, after the selection of the relevant sites, we looked for temporal changes with mid-to-long-term monitoring activity following a constant sampling rate. This allowed us to gain better insight into the relationships between the fluid circulation and the faulting activity. The sampling sites are listed in Table 1, along with the analytical results of the gas phase.

Description: Published

Description: 815-821

Description: 3.2. Tettonica attiva

Description: JCR Journal

Description: open

Description: Emissions of volcanoes and their depositions do have an immediate impact on their surrounding environment. In the present study, emissions and depositions of the active volcanic and geothermal system Vulcano (Italy) were investigated by active moss biomonitoring (Fig. 1) in the spring of 2012. Sphagnum moss bags were exposed for periods of 3 days, 3, 6 and 9 weeks. Soil and rainwater samples as well as meteorological data were also collected. After exposure, mosses were oven-dried, grinded and each sample was extracted either in deionized water or HNO3 (with H2O2). Extraction solutions were analyzed by ICP-MS for total concentrations of Li, Mg, Sr, Ba, Cr, Mn, S, Fe, Co, Cu, Zn, Mo, W, Tl, As, Sb, Bi, I, and Se. Soil and rain water samples were analyzed for the same trace elements. For elements such as As and Tl, deionized water extracts showed comparable concentrations to HNO3 extracts, indicating either the absence of particles or the presence of water-soluble particles. Elements such as Pb, Ba, Se and Sr were only dissolved to about 10 % or less in deionized water, indicating a significant share of water-insoluble particle formation. Distribution patterns of emissions and depositions over the whole island of Vulcano allowed classifying all investigated elements into four groups based on their origin (Fig. 2). Lithium was found ubiquitously on the island thus likely is of either marine or geogenic origin (group a in Fig. 2). The elements Mg, Fe, Sr, Mn, Zn, Co, and W were found predominantly on the crater where bare soil was present, and were grouped as “soilborne elements” (group b). These elements are characterized by deposition close to their source of origin. Elements with higher concentrations at the fumarolic field were grouped according to their transport characteristics. The elements I, Se, Tl, Bi, Sb, As, and S were considered as true volatiles (group c) being found also further away from the fumarolic field than Pb, Cr, Mo, and Ba which were interpreted to be predominantly emitted as particles (group d). Moss-bag biomonitoring proved to be an effective tool for the study of emission and deposition processes in active volcanic areas which also allows a classification of elements accumulated on the moss by their origin and distribution patterns.

Description: Published

Description: Patras, Greece

Description: 4.5. Studi sul degassamento naturale e sui gas petroliferi

Description: open

Description: La rivista non prevede l'Abstract e inizia direttamente dall'Introduzione, che viene sotto riportata. In ambiente vulcanico, al fine di monitorare e studiare l’azione delle sorgenti, è di fondamentale importanza riuscire a misurare con estrema precisione l’espansione/contrazione del mezzo. Questo è ottenibile attraverso l’utilizzo di strumenti noti come borehole strainmeters (o dilatometri da pozzo). Lo strumento di base e' da un punto di vista teorico abbastanza semplice. Consiste di un tubo cilindrico, al suo interno riempito di specifico fluido (solitamente olio di silicone), da installare in un foro appositamente trivellato ponendolo in contatto con le pareti rocciose del foro attraverso l’utilizzo di cementi ad espansione, che consentono un perfetto accoppiamento strumento-mezzo. La variazione di livello del fluido indotta dalla variazione dello strain nel mezzo circostante è quindi misurata con estrema precisione attraverso un apposito sensore. I dilatometri da pozzo sono gli strumenti più sensibili alle variazioni dello stato degli sforzi finora realizzati a fini geofisici (sensibilità nominale dV/V fino a 10-12). La tipologia di strumentazione utilizzata nelle installazioni all’Etna è quella nota come Sacks-Evertson borehole strainmeters (o dilatometers) [Sacks et al., 1971]. Le principali caratteristiche tecniche della strumentazione sono riportate in tabella 1. Gli strainmeters e l’elettronica di controllo sono prodotti dal Department Terrestrial Magnetism (DTM) del Carnegie Institution di Washington. I colleghi del DTM sono presenti alle fasi finali d’installazione e di avvio dell’operatività strumentale.

Description: Published

Description: 1-25

Description: 5V. Sorveglianza vulcanica ed emergenze

Description: N/A or not JCR

Description: open

Description: Here, we report the first continuous data of geochemical parameters acquired directly from the active summit crater of Vulcano. This approach provides a means to better investigate deep geochemical processes associated with the degassing system of Vulcano Island. In particular, we report on soil CO2 fluxes from the upper part of Vulcano, a closed-conduit volcano, from September 2007 to October 2010. Large variations in the soil CO2 and plume SO2 fluxes (order of magnitude), coinciding with other discontinuous geochemical parameters (CO2 concentrations in fumarole gas) and physical parameters (increase of shallow seismic activity and fumarole temperatures) have been recorded. The results from this work suggest new prospects for strengthening geochemical monitoring of volcanic activity and for improving the constraints in the construction of a “geochemical model”, this being a necessary condition to better understand the functioning of volcanic systems.

Description: Published

Description: 1859-1863

Description: 2V. Dinamiche di unrest e scenari pre-eruttivi

Description: 4V. Vulcani e ambiente

Description: 5V. Sorveglianza vulcanica ed emergenze

Description: 1R. Reti di monitoraggio e Osservazioni

Description: JCR Journal

Description: restricted

Description: Radon-in-soil monitoring at the Poas volcano (Costa Rica) has been performed together with water chemistry from the hot crater lake since 1981 and 1983 respectively. The results are discussed as a function of the eruptive evolution of the volcano over a 13 years period (1981-1994). It is shown that no definitely clear precursory radon signals have been recorded. On the contrary, ionic species concentrations are likely to be considered good precursors, together with the temperature variations of the crater lake water.

Description: Published

Description: JCR Journal

Description: open

Description: A theoretical method for estimating the characteristics of radon transport in homogeneous soil is developed. The method allows the following characteristics to be estimated: depth distribution function of the soil gas radon concentration, equilibrium radon concentration in the soil air, depth at which the radon concentration reaches its equilibrium value, radon flux density from the Earths surface, and convective radon transport velocity. The method is based on soil gas radon concentration measurements and is appropriate in the case of relatively uniform geology.

Description: Published

Description: JCR Journal

Description: open

Description: The identified emissions of abiogenic carbon dioxide, carbon monoxide and methane are generally attributed to volcanic activity or to geochemical processes associated with thermometamorphic effects. In this paper we show another possible abiogenic source of emission, induced by mechanical, and not thermal, stresses. We investigated the mechanochemical production of carbon dioxide and methane when friction is applied to marly-type rock and studied the mechanisms determining the strong CO2 and CH4 emissions observed. A ring mill was used to apply friction and oriented pressure upon a synthetic calcite-clay mixture of varying proportions. We found that the CO2 and CH4 release versus the grinding action has a non-linear trend reflecting the behaviour of decreasing crystallinity, which indicates a close link between crystallinity and gas production. For the CO2 emission, we propose a release mechanism connected with the friction-induced fractures and the increase in structural disorders induced by creep in the lattice. The CH4 emission could be explained by a Sabatier reaction in which CO2 and hydrogen are involved to form CH4 and water.

Description: Published

Description: JCR Journal

Description: open

Description: Sampled from the Gangxi oil field in the Huanghua depression, Bohaiwan Basin, the crude oil He and Ar isotopic compositions and their geochemical significance were investigated. The result shows that i) the 3He/4He values of the six oil samples free from air contamination indicate a mantle helium contribution ranging between 13.9% and 32.8% and averaging 24.1%, which means that the Gangxi oil field once had a tectonic background of the mantle-derived helium input and higher geothermal flow with an average of 75.0 mWm-2; ii) deduced from the 40Ar/36Ar aging effect the Gangxi oil should be derived from the Tertiary; iii) water injection is the main reason for the air contamination for the Gangxi oil noble gases and the relations between 3He/4He and 4He/20Ne as well as 40Ar/36Ar and 4He/20Ne are of an applicative potential in estimating the water injection effect and the connectivity of producing formations. The search for the crude oil He and Ar isotopes provides a new approach to inferring natural gas and oil sources, tectonic backgrounds, geothermal flow and water injection effect.

Description: Published

Description: JCR Journal

Description: open

Description: Within the framework of the European MVRRS project (Mitigation of Volcanic Risk by Remote Sensing Techniques), in June 1997 an airborne campaign was organised on Mt. Etna to study different characteristics of the volcanic plume emitted by the summit craters in quiescent conditions. Digital images were collected with the Airborne Multispectral Imaging Spectrometer (MIVIS), together with ground-based measurements. MIVIS images were used to calculate the aerosol optical thickness of the volcanic plume. For this purpose, an inversion algorithm was developed based on radiative transfer equations and applied to the upwelling radiance data measured by the sensor. This article presents the preliminary results from this inversion method. One image was selected following the criteria of concomitant atmospheric ground-based measurements necessary to model the atmosphere, plume centrality in the scene to analyse the largest plume area and cloudless conditions. The selected image was calibrated in radiance and geometrically corrected. The 6S (Second Simulation of the Satellite Signal in the Solar Spectrum) radiative transfer model was used to invert the radiative transfer equation and derive the aerosol optical thickness. The inversion procedure takes into account both the spectral albedo of the surface under the plume and the topographic effects on the refl ected radiance, due to the surface orientation and elevation. The result of the inversion procedure is the spatial distribution of the plume optical depth. An average value of 0.1 in the wavelength range 454-474 nm was found for the selected measurement day.

Description: Published

Description: JCR Journal

Description: open

Description: The broad-band teleseismics records of the earthquake of October 29,1989 in Algeria (MW = 6.0) allow a detailed study of the rupture process of this earthquake. The focal mechanism obtained by P and SH modeling corresponds to reverse faulting with a small amount of left-lateral movement along a fault striking 246° and dipping 56°. The rupture is found to be complex with two sub-events separated in time but occurring on the same plane. The lowfrequency records of an accelerometer located some 25 km to the west of the main shock are also better fi tted when the rupture is composed of a double pulse. In the two cases, there is strong evidence for the rupture to propagate from south-west towards north-east.The relocalisation of the main shock by using a master-event technique and the data from Italian and Spanish stations led to the same conclusions. Soon after the main event, a temporary seimic network was installed in the epicentral area. The aftershock clouds defi ne a SW-NE fault dipping to the NW compatible with the results of the modelisations of the teleseismic body-waves and the accelerogram. The focal mechanisms correspond mainly to reverse faulting. The maximum principal direction of the stress tensor obtained from the inversion is about N-S and the minimum is vertical, typical of a compressive regime. The Chenoua earthquake took place on a fault which was not recognized as active. Repeated comparable seismic events on this fault and on the fault that borders the massif to the south explain this intriguing topographic feature.

Description: Published

Description: JCR Journal

Description: open

Description: Seismic monitoring in Italy has strongly improved since the 1997 Umbria-Marche earthquake sequence. This has made the National Seismic Network (RSN) a powerful tool both to rapidly locate and quantify thousands of earthquakes occurring in Italy every year, and to study the seismic activity in detail, accumulating an impressive high quality data set that will be exploited in the coming years to understand earthquake processes and to investigate the deep structure. This paper summarizes and compares the basic features of the seismicity recorded in 2000 and 2006, before and after the implementation of the new RSN, showing that the number of well located earthquakes has more than doubled and that the completeness magnitude has dropped from ~2.3 to ~1.7. In addition, we concentrate on the evaluation of the current automatic location and magnitudes versus the revised ones, published routinely in the INGV bulletins. We show that the rapid estimates of locations and magnitudes are robust and reliable for most regions in Italy: more than 75% of the earthquakes are located in real time within 10km from the «true» locations, whereas the rapid magnitudes ML are within ±0.4 from the revised values in 90% of cases. The comparison between real-time and revised locations shows that there are a few regions in Italy where a further network improvement is still desirable. These include all the off-shore regions, Calabria, western Sicily, the Alpine and Po Plain region, and some small areas along the peninsula.

Description: Published

Description: 417-431

Description: 5.2. TTC - Banche dati di sismologia strumentale

Description: JCR Journal

Description: open

Description: We present an empirical model of sulphur solubility that allows us to calculate f S2 if P, T, fO2 and the melt composition, including H2O and S, are known. The model is calibrated against three main experimental data bases consisting in both dry and hydrous silicate melts. Its prime goal is to calculate the f S2 of hydrous basalts that currently lack experimental constraints of their sulphur solubility behaviour. Application of the model to Stromboli, Vesuvius, Vulcano and Etna eruptive products shows that the primitive magmas found at these volcanoes record f S2 in the range 0.1-1 bar. In contrast, at all volcanoes the magmatic evolution is marked by dramatic variations in f S2 that spreads over up to 9 orders of magnitude. The f S2 can either increase during differentiation or decrease during decompression to shallow reservoirs, and seems to be related to closed versus open conduit conditions, respectively. The calculated f S2 shows that the Italian magmas are undersaturated in a FeS melt, except during closed conduit conditions, in which case differentiation may eventually reach conditions of sulphide melt saturation. The knowledge of f S2, fO2 and fH2O allows us to calculate the fluid phase composition coexisting with magmas at depth in the C-O-H-S system. Calculated fluids show a wide range in composition, with CO2 mole fractions of up to 0.97. Except at shallow levels, the fluid phase is generally dominated by CO2 and H2O species, the mole fractions of SO2 and H2S rarely exceeding 0.05 each. The comparison between calculated fluid compositions and volcanic gases shows that such an approach should provide constraints on both the depth and mode of degassing, as well as on the amount of free fluid in magma reservoirs. Under the assumption of a single step separation of the gas phase in a closed-system condition, the application to Stromboli and Etna suggests that the main reservoirs feeding the eruptions and persistent volcanic plumes at these volcanoes might contain as much as 5 wt% of a free fluid phase. Consideration of the magma budget needed to balance the amounts of volatiles emitted in the light of these results shows that the amount of nonerupted magma could be overestimated by as much as one order of magnitude.

Description: Published

Description: JCR Journal

Description: open

Description: We have characterized the textures of pumice clasts from Phlegraean Fields to gain insights into the conduit flow-dynamics of alkaline explosive eruptions. Vesicularities, vesicle number densities, and vesicle sizes and shapes were measured to obtain the bulk and groundmass properties of the juvenile fraction of Campanian Ignimbrite (CI) and Agnano Monte Spina (AMS) eruptions. The results report the coexistence of three end-member pumice types in the deposits of both eruptions, 1) microvesicular, 2) tube and 3) expanded, which differ according to clast morphology and the macro- to microscopic vesicle texture. Vesicularities (0.85-0.94 for CI, 0.51-0.91 for AMS) and vesicle number densities (2-4×105 cm-2 in CI, 3×105-106 cm-2 in AMS) span quite a wide range in all the three pumice types. Overall, tube pumices exhibit the highest bulk (0.89) and groundmass (CI 0.85, AMS 0.82) average vesicle volume fractions but the lowest average vesicle number densities (CI 2×105, AMS 4×105 cm-2). Comparison with textures of calc-alkaline pumices has revealed many similarities and points to a common origin and distribution of the products from both magma compositions within the volcanic conduit. In addition, the results of the textural analysis were interpreted in the light of the conduit flow modeling of Phlegraean Fields eruptions. The comparison of textural observations with results from simulations of conduit magma ascent has exhibited a good agreement between measured and numerically calculated vesicularities for both compositions, helping to constrain the overall dynamics of alkaline versus calc-alkaline eruptions.

Description: Published

Description: JCR Journal

Description: open

Description: An overview of novel laser techniques suitable for volcanic monitoring, based on different kinds of infrared laser sources, is presented. Their main advantages and drawbacks are discussed focusing on the achievable sensitivity and precision levels in analysis of gaseous species. Some of the most recent experimental results obtained in laboratory development as well as in field tests of home-built laser spectrometers are reported. New perspectives in optical devices aimed at geochemical and geophysical applications are also considered.

Description: Published

Description: JCR Journal

Description: open

Description: The El Camp Fault (Catalan Coastal Ranges, NE Iberian Peninsula) is a slow slipping normal fault whose seismic potential has only recently been recognised. New geomorphic and trench investigations were carried out during a training course across the El Camp Fault at the La Porquerola alluvial fan site. A new trench (trench 8) was dug close to a trench made previously at this site (trench 4). With the aid of two long topographic profiles across the fault scarp we obtained a vertical slip rate ranging between 0.05 and 0.08 mm/yr. At the trench site, two main faults, which can be correlated between trenches 8 and 4, make up the fault zone. Using trench analysis three paleoseismic events were identified, two between 34.000 and 125.000 years BP (events 3 and 2) and another event younger than 13 500 years BP (event 1), which can be correlated, respectively, with events X (50.000- 125.000 years BP), Y (35.000-50.000 years BP) and Z (3000-25.000 years BP). The last seismic event at the La Porquerola alluvial fan site is described for the first time, but with some uncertainties.

Description: Published

Description: JCR Journal

Description: open

Description: On 17th and 18th July 2001, several fractures opened on Mt. Etna southern flank generating different lava flows spreading both in Valle del Bove and towards Nicolosi. On 29th July the image spectrometer MIVIS was flown over Mt. Etna to acquire high-resolution images of the eruption. The MIVIS airborne campaign was planned simultaneously with TERRA, EO-1 and Landsat 7 satellite acquisitions, in order to compare hyperspectral and multispectral data referred to active lavas. This work focuses on the thermal mapping of lava flows, taking advantage of MIVIS sensor high technical performances. The MIVIS high spatial resolution allows a detailed analysis of the lava flow topographic distribution. Its 12 bit dynamic range consents an estimate of the temperature even for the «hottest» pixels. The main target of this work is the evaluation of the energy flux by means of remote-sensing techniques. Surface temperature analysis was performed on distinct lava flows using the dualband technique. These quantities were compared with the integrated temperatures retrieved using the MIVIS thermal infrared bands. The influence of topography was also considered in the flux calculation using a Digital Elevation Model (DEM) of Mt. Etna.

Description: Published

Description: JCR Journal

Description: open

Description: Recent seismological studies contribute to better understand the first order characteristics of earthquake occurrence in Italy, identifying the potential sites for moderate to large size earthquakes. Ad hoc passive seismic experiments performed in these areas provide information to focus on the location and geometry of the active faults more closely. This information is relevant for assessing seismic hazard and for accurately constraining possible ground shaking scenarios. The area around the Città di Castello Basin, in the Northern Apennines (Central Italy), is characterized by the absence of instrumental seismicity (M 〉 2.5), it is adjacent to faults ruptured by recent and historical earthquakes. To better understand the tectonics of the area, we installed a dense network of seismic stations equipped with broadband and short period seismometers collecting data continuously for 8 months (October 2000-May 2001). The processing of ~ 900 Gbyte of data revealed a consistent background seismicity consisting of very low magnitude earthquakes (ML 〈 3.2). Preliminary locations of about 2200 local earthquakes show that the area can be divided into two regions with different seismic behaviour: an area to the NW, in between Sansepolcro and Città di Castello, where seismicity is not present. An area toward the SE, in between Città di Castello, Umbertide and Gubbio, where we detected a high microseismicity activity. These findings suggest a probable different mechanical behaviour of the two regions. In the latter area, the seismicity is confined between 0 and 8 km of depth revealing a rather well defined east-dipping, low angle fault 35 km wide that cuts through the entire upper crust down to 12-15 km depth. Beside an apparent structural complexity, fault plane solutions of background seismicity reveal a homogeneous pattern of deformation with a clear NE-SW extension.

Description: Published

Description: JCR Journal

Description: open

Description: On 27 February 2007, a new eruption occurred on Stromboli which lasted until 2 April. It was characterized by effusive activity on the Sciara del Fuoco and by a paroxysmal event (15 March). This crisis represented an opportunity for us to refine the model that had been developed previously (2002-2003 eruption) and to improve our understanding of the relationship between the magmatic dynamics of the volcano and the geochemical variations in the fluids. In particular, the evaluation of the dynamic equilibrium between the volatiles (CO2 and SO2) released from the magma and the corresponding fluids discharged from the summit area allowed us to evaluate the level of criticality of the volcanic activity. One of the major accomplishments of this study is a four-year database of summit soil CO2 flux on the basis of which we define the thresholds (Low-Medium-High) for this parameter that are empirically based on the natural volcanological evolution of Stromboli. The SO2 fluxes of the degassing plume and the CO2 fluxes emitted from the soil at Pizzo Sopra la Fossa are also presented. Noteworthy geochemical signals of volcanic unrest have been clearly identified before, during, and after the effusive activity. These signals were found almost simultaneously in the degassing plume (SO2 flux) and in soil degassing (CO2 flux) at the summit, although the two degassing processes are shown to be clearly different. The interpretation of the results will be useful for future volcanic surveillance at Stromboli.

Description: In press

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: In questo lavoro viene descritta l’installazione di una rete mobile nell’area dei Monti Nebrodi in seguito all’evento del 23-06-2011 di Ml = 4.6 e come tale intervento ha contribuito al miglioramento della localizzazione delle sorgenti sismiche soprattutto nella determinazione della profondità degli eventi. Verranno anche presentati i risultati delle localizzazioni ottenute attraverso l’integrazione dei dati acquisiti durante questa campagna, con quelli della rete sismica permanente dell’INGV-Osservatorio Etneo ( INGV -OE).

Description: Istituto Nazionale di Geofisica e Vulcanologia

Description: Published

Description: 1-24

Description: 4IT. Banche dati

Description: N/A or not JCR

Description: open

Description: Il Centro di Ricerche Sismologiche (CRS) dell’Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS è stato istituito con la legge n. 399 del 30 novembre 1989 col fine istituzionale di: “...svolgere, in autonomia scientifica e secondo specifici progetti: ricerche sulla sismicità e sulla sismogenesi dell’Italia nordorientale, gestendo e sviluppando inoltre la connessa rete di rilevamento sismico anche per fini di protezione civile. Nei campi di sua competenza il dipartimento svolge inoltre: attività applicativa; studi e ricerche sulle tecnologie di acquisizione, trasmissione e trattamento del segnale sismico; studi e ricerche per l’affinamento del modello sismotettonico dell’Italia nord-orientale.” Dal 2003, in seguito alla conferenza “Integrating the Seismic Monitoring in Central Europe” tenutasi a Udine e al Workshop “Beyond Frontiers: Seismic Networks in the Southern Alps” organizzato a Trieste, l’OGS ha partecipato al progetto europeo Interreg IIIa Italia/Austria “Reti sismologiche senza frontiere nelle Alpi sudorientali” 1. Il progetto nasce dalla stretta collaborazione esistente tra: • il CRS dell’OGS a Udine; • la Protezione Civile della Regione Friuli-Venezia Giulia (FVG); • l’allora Dipartimento di Scienze della Terra (DST) dell’Università di Trieste (adesso Dipartimento di Geoscienze); • lo Zentralanstalt für Meteorologie und Geodynamik, Hauptabteilung Geophysik di Vienna in Austria (ZAMG); • l’Urad za seizmologijo, geologijo, Agencija Republike Slovenije za okolje, di Lubiana in Slovenia (ARSO). Il terremoto di Bovec, avvenuto in prossimità dei confini tra FVG, Carinzia e Slovenia nel 1998, ha evidenziato l’importanza di un’integrazione e potenziamento delle reti delle diverse nazioni. In particolare, in tale occasione si è evidenziato: l’eterogeneità della strumentazione esistente nelle diverse reti, la mancanza di connessione dedicata tra i centri sismologici anche all’interno della stessa nazione e la mancanza di un sistema di elaborazione ed archiviazione dei dati omogeneo. Lo scopo del progetto è stato quindi l’integrazione transfrontaliera delle reti sismologiche presenti nelle tre nazioni per far fronte alle necessità di protezione civile e per scopi di ricerca scientifica. La disponibilità in tempo reale di forme d’onda dei terremoti permette, infatti, l’analisi immediata dei dati in maniera automatica che fornisce informazioni rapide ed affidabili alle autorità di protezione civile. Gli obiettivi principali raggiunti durante il progetto sono: 1. la creazione di un centro di raccolta dati in tempo reale presso la Sala Operativa Regionale (SOR) di Palmanova della Protezione Civile del Friuli-Venezia Giulia e l’adattamento dei centri raccolta dati del DST, dell’OGS e di Vienna a questi scopi. La duplicazione dei centri di raccolta dati e delle connessioni tra questi garantisce il funzionamento del sistema anche nel caso che uno o più centri siano fuori uso per i danni subiti da un sisma distruttivo; 2. l’individuazione e la realizzazione di uno o più sistemi di connessione dati efficienti e sicuri tra le stazioni ed i centri di raccolta; 3. la ridefinizione della geometria attuale delle reti, in funzione della migliore copertura possibile delle aree potenzialmente pericolose a ridosso dei confini di stato; 4. la programmazione dei protocolli comuni d’intervento in caso di forti terremoti.

Description: Published

Description: 38-41

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: Attualmente presso la sede di Ancona del CNT sono acquisiti i dati relativi a 58 stazioni in realtime ed a 13 stazioni dial-up. In particolare la sede di Ancona ha la funzione di server nei confronti della sala sismica nazionale per 28 stazioni in realtime e client per le rimanenti 30. Le stazioni dial-up hanno una connessione con radio modem (8) o con modem GSM (5). Gli acquisitori gestiti sono: GAIA1 e GAIA2, Trident/Cygnus, HDR24 e Lennartz Mars88/MC/RC. I sensori sono: Trillium 40-120-240s; Lennartz LE3D- 5s/1s/lite/BH, Mark L4-3D, Episensor ES-T. Il sistema di acquisizione dati è basato su Seiscomp31, mentre la detezione degli eventi avviene tramite Earthworm

Description: Published

Description: 19-21

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: (extended abstract)

Description: INGV, Regione Sicilia, Ministero Sviluppo Economico

Description: Published

Description: Ettore Majorana Foundation and Centre for Scientific Culture, Erice, Sicily

Description: 3.2. Tettonica attiva

Description: 3.3. Geodinamica e struttura dell'interno della Terra

Description: open

Description: Volcanic emissions are considered one of the major natural sources of several trace metals (e.g. As, Cd, Cu, Pb, and Zn) to the atmosphere [Nriagu, 1989], and the geochemical cycles of these elements have to be considered strongly influenced by volcanic input. However, the accurate estimation of the global volcanic emissions of volatile trace metals into the atmosphere is still affected by a high level of uncertainty. The latter depends on the large variability in the emission of the different volcanoes, and on their changing stage of activity. Moreover, only few of the potential sources in the world have been directly measured [Hinkley et al. 1999]. Atmospheric deposition processes (wet and dry) are the pathways through which volcanic emissions return to the ground (soils, plants, aquifers), resulting in both harmful and beneficial effects [Baxter et al. 1982; Aiuppa et al. 2000; Brusca et al. 2001; Delmelle, 2003; Bellomo et al. 2007; Martin et al. 2009; Floor et al. 2011; Calabrese et al. 2011]. In the first part of this study we present the results of a literature review on trace metals emissions from active volcanoes around the world. In the second part, we present new data on the fluxes of the trace metals from Etna (Italy) and four active volcanoes in the world: Turrialba (Costarica), Nyiragongo (DRC), Mutnovsky and Gorely (Kamchatka). We found 27 publications (the first dating back to the 70’s), 13 of which relate to the Etna and the other include some of the world’s most active volcanoes: Mt. St. Helens, Erebus, Merapi, White Island, Kilauea, Popocatepetl, Galeras, Indonesian arc, Satasuma and Masaya. The review shows that currently there are very few data available, and that the most studied volcano is Mt. Etna. Using these data, we defined a range of fluxes for As, Ba, Bi, Cd, Cu, Fe, Mn, Pb, Se, V and Zn (Figure 1). To obtain new data we sampled particulate filters at the five above mentioned volcanoes. Filters were mineralized (acid digestion) and analyzed by ICP-MS. Sulphur to trace element ratios were related to sulphur fluxes to indirectly estimate trace elements fluxes. Etna confirms to be one of the greatest point sources in the world. The Nyiragongo results to be also a significant source of metals to the atmosphere, especially considering its persistent state of degassing from the lava lake. Also Turrialba and Gorely have high emission rates of trace metals considering the global range. Only Mutnovsky Volcano show values which are sometimes lower than the range obtained from the review, consistent with the fact that it is mainly a fumarolic field. This work highlights the need to expand the current dataset including many other active volcanoes for a better constraint of global trace metal fluxes from active volcanoes.

Description: Published

Description: Nicolosi (Catania)

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: open

Description: Volcanic emissions represent one of the most relevant natural sources of trace elements to the troposphere, both during and between eruptions. Due to their potential toxicity they may have important environmental impacts from the local to the global scale. Mount Etna, the largest European volcano and one of the most active volcano in the world, covers an area of about 1250 km2 and reaches an altitude of about 3340 m. It has been persistently active during historical time, with frequent paroxysmal episodes separated by passive degassing periods. Atmospheric precipitation was collected approximately every two weeks, from April 2006 to December 2007, using a network of five rain gauges, located at various altitudes on the upper flanks around the summit craters of Etna Volcano. The collected samples were analysed for major (Ca, Mg, K, Na, F, SO4, Cl, NO3) and a large suite of trace elements (Ag, Al, As, Au, B, Ba, Be, Bi, Cd, Co, Cr, Cs, Cu, Fe, Hg, La, Li, Mn, Mo, Ni, Pb, Rb, Si, Sb, Sc, Se, Sr, Th, Ti, Tl, U, V, Zn) by using different techniques (IC, SPEC, ICP-MS and CV-AFS). The monitoring of atmospheric deposition gave the opportunity to occasionally sample volcanic fresh ashes emitted by the volcano during the paroxysmal events. This was possible because the network of five rain gauges were equipped with a filter-system to block the coarse material. In this way, more than twenty events of ashfall were collected. Unfortunately, only half of these samples were suitable for a complete chemical analysis, because of the small amount of sample. In order to obtain elemental chemical composition of ashes, powdered samples were analysed by a combination of methods, including X-ray Fluorescence Spectroscopy (XRF), total digestion followed by Inductively Coupled Plasma Emission Mass Spectrometry (ICP-MS), Instrumental Neutron Activation Analysis (INAA), and infrared detection (IR). The chemistry of rainwater reveals that most of the investigated elements have higher concentrations close to the emission vent of the volcano, confirming the prevailing volcanic contribution. Rainwater composition clearly reflects the volcanic plume input. Ash-normalised rainwater composition indicates a contrasting behaviour between volatile elements, which are highly-enriched in rainwater, and refractory elements, which have low rainwater/ash concentration ratios. The degree of interaction between collected ash and rainwater was variable, depending on several factors: (i) the length of the period in which tephra was present in the sampler (the ash fall may have occurred any day from the first to the last day of the rain collecting period); (ii) the amount of rainwater fallen on the collectors after the ash-fall event, and its acidity; (iii) the granulometry of the ash samples that was widely variable (from few centimetres to micrometric particles) increasing the interaction with decreasing dimensions of the grains; (iv) the distance of collector with respect to the craters. In order to investigate the role of volcanic ash on the evolution of the rainwater chemistry, absolute concentrations of rain and ash were plotted in binary plot diagrams (Figure 1). Each diagram corresponds to a single event, and pH and TDS of the solution collected is reported. The diagonal bars in the diagrams represent the rain/ash ratios (1:1 and 1:10000). The results confirm that sulphate and halide salt aerosols are adsorbed onto ash particles, and their rate of dissolution in rainwater depends on solubility. Moreover, rapid chemical weathering of the silicate glass by volcanic acid (SO2, HCl and HF) can also explain the enrichment of several refractory elements (Na, K, Ca, Mg, Si, Al, Fe, Ti, Sc). Our observations highlight how explosive activity can increase enormously the deposition rate of several chemical elements, up to several km away from the emission vents.

Description: Published

Description: Nicolosi (Catania)

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: open

Description: The study area is a 130 km long fast spreading graben in Central Greece bordered by active faults. Its complex geodynamical setting includes the presence at depth of a subduction slab responsible for the recent (Quaternary) volcanic activity in the area which possibly represents the northward continuation of the South Aegean active volcanic arc. To the area belongs also the western termination of the North-Anatolian fault a tectonic lineament of regional importance. The high geothermal gradient of the area is evidenced by the presence of many thermal springs with temperatures from 19 to 82 °C, issuing along the normal faults bordering the graben. In the period 2004-2012 more than 60 gas and water samples have been collected and their chemical and isotopic analysis revealed a wide range of compositions. Going from west to east the gas composition changes (Fig. 1) from CH4- to CO2-dominated passing through mixed N2-CH4 and N2-CO2 compositions, while at the same time the He isotopic composition goes from typical crustal values (0.02 R/Ra) up to 0.87 R/Ra (corrected for air contamination), showing in the easternmost sites a small but significant mantle input (up to ~ 10%). Isotopic composition of CH4-C indicates a thermogenic origin for the CH4-rich samples (δ13C from -50 to -37 ‰) and hydrothermal origin for the remaining samples (〉 -25‰). Positive δ15N values (around +2 ‰) indicate a contribution of crustal derived nitrogen for the N2-rich samples. The most pristine values of δ13C(CO2) refer to the most CO2-rich samples. These values (~ -3 ‰) point to a mixed mantle-marine carbonate source. Lower δ13C values (-10 ÷ -5 ‰) of the other sites can be explained by loss of CO2 due to dissolution processes. Also temperature and salinity of the waters shows differences along the graben increasing from west to east (Fig. 2). Two main groups can be separated on the basis of the total dissolved salts (TDS). The first, represented by dilute waters (TDS 〈 500 mg/l), is found in the westernmost sites characterised by the presence of CH4-rich and mixed N2-CH4 gases. The remaining waters display higher salinities (TDS from 9 to 35 g/l) due to the mixing with high salinity waters. The water composition can be explained by mixing of two end-members, one with low salinity of meteoric origin and the other with high salinity of marine origin. The mixing can be evidenced in Fig. 2. Low salinity waters show low chloride contents and their light water isotope composition overlaps the field of the cold groundwaters of the area confirming their meteoric origin. High salinity waters are aligned along the mixing line between the cold groundwaters and the seawater confirming the contribution of marine component. Most of the water compositions in the triangular graph of Giggenbach fall in the field of the non equilibrated waters being therefore unsuitable for geothermometric estimations. Only the easternmost sites (Gialtra, Ilion and Edipsos) falling the field of the partially equilibrated waters yield estimated temperatures in the range 150-170 °C. Silica geothermometers confirm these estimations. This study revealed that the complex geodynamic setting of the area is clearly reflected in the wide compositional range of the gases collected in the area that evidence contributions from different end-members (atmosphere, crust, mantle and hydrothermal systems). Water chemistry can be explained mainly from the mixing of a meteoric low-salinity end-member with a high-salinity marine end-member partially modified by hydrothermal water-rock interactions. The highest estimated temperatures in the hydrothermal reservoirs are in the range 150-170 °C.

Description: Published

Description: Patras, Greece

Description: 4.5. Studi sul degassamento naturale e sui gas petroliferi

Description: open

Description: Published

Description: 7A. Geofisica di esplorazione

Description: reserved

Description: A seismic noise recording experiment has been carried out in the Campi Flegrei volcanic area from March 9 to 26, 2009 in the framework of the INGV-DPC 2007-2009 agreement (Project V1 – UNREST). The project aimed at the realization of an integrated method for the definition of the unrest phases at Campi Flegrei. 21 digital three-component seismic stations equipped with broad band seismometers have been added to the existing 11 digital stations already deployed in the area. The preliminary results show a correlation between the seismic noise level and the anthropic activity, whereas the meteorological conditions seem affecting the low frequency seismic noise. These results are important to define the detection thresholds of the seismic signals generated during a possible renewal phase of the volcanic activity.

Description: Published

Description: 1-21

Description: N/A or not JCR

Description: open

Description: L’utilizzo di sensori in pozzo ha l’obiettivo di migliorare il rapporto segnale-disturbo per poter registrare segnali di eventi sismici in zone dove le registrazioni in superficie sono corrotte dai disturbi. Infatti, le registrazioni superficiali sono affette dal noise sismico ambientale il quale è particolarmente elevato in zone industrializzate a frequenze generalmente superiori ad 1 Hz [McNamara and Buland, 2004]. La RSN dell’INGV, gestita dal CNT [vedi Delladio, 2011 - in questo volume], è dotata attualmente di 6 sensori in pozzo, ubicati nelle seguenti località: Castelleone (CR), Imola (BO), Bellaria (RN), Senigallia (AN), Sansepolcro (AR), Città di Castello (PG). Le prime 4 località si trovano in pianura padana (Castelleone e Imola) e sulla costa adriatica (Bellaria e Senigallia): in questi siti l’utilizzo di un sensore in pozzo ha lo scopo di ottenere registrazioni in cui i disturbi antropici possano essere significativamente abbattuti, in quanto le aree citate sono tra le più industrializzate e urbanizzate del territorio nazionale [Marzorati and Bindi, 2006]. I pozzi di Sansepolcro e Città di Castello rientrano nell’area di interesse della Faglia Alto Tiberina, in cui terremoti di piccolissima magnitudo vengono registrati solo in siti particolarmente silenziosi dal punto di vista del noise sismico ambientale; perciò i due sensori in pozzo hanno lo scopo di avere un punto di osservazione più vicino alla sorgente dei segnali che si vogliono registrare. Nei prossimi paragrafi sono mostrati alcuni esempi utili per poter valutare l’efficienza dei sensori in pozzo.

Description: Published

Description: 72-75

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: N/A or not JCR

Description: open

Description: In this paper the history of the Mobile Seismic Network of the Osservatorio Vesuviano (at present Department of Napoli of the Istituto Nazionale di Geofisica e Vulcanologia – INGV) is described. The instrumental development and the main research and monitoring activities since the early 1980’ are reported. Starting from the analog stations with magnetic tape recording to the first digital stations with trigger recording, until the modern multichannel 24bit devices, the technological development of the last 30 years has given a strong contribution to increase the knowledge in the seismology and seismotectonics fields. The Mobile Seismic Network has been engaged in active and passive seismic studies both on volcanic and tectonic areas. Particularly, the contribution of the Mobile Seismic Network for the monitoring of Neapolitan active volcanoes has been very important to improve the Permanent Network. During seismic crises high quality data have been gathered allowing detailed analyses of the seismic activity. Moreover, the time synchronization by means of GPS time code allowed the deployment of the Mobile Network abroad and the collaboration with the main international research institutes. At present, the Mobile Seismic Network of the Osservatorio Vesuviano is developing on multichannel acquisition systems, also in array configuration, to gathered simultaneously seismic signals with a large frequency band.

Description: Published

Description: 1-51

Description: 1.4. TTC - Sorveglianza sismologica delle aree vulcaniche attive

Description: 3.2. Tettonica attiva

Description: N/A or not JCR

Description: open

Description: This paper describes the analyses of the single-station ambient-vibration measurements performed on the Italian accelerometric network to detect site resonance phenomena potentially affecting earthquake recordings. The use of low cost, high quality microtremor measurement can be helpful to discriminate among soil classes, since several classification schemes based on resonance frequencies were proposed in the last decades. Operatively, in the framework of the Italian Strong Motion Database project (DPC-INGV 2007–2009 S4; http://esse4.mi.ingv.it), soil resonance frequencies have been evaluated from more than 200 ambient vibration measurements in correspondence of accelerometric stations included in ITACA (http://itaca.mi.ingv.it/ItacaNet/). The noise recordings have been analyzed using the same numerical protocol in order to standardize the results. Particular attention has been paid to evaluate the quality of measurements and to develop an on-purpose mathematical tool to automatically estimate the peaks in the horizontal-to-vertical spectral ratio (HVSR) curve. The reliability of the resonance frequencies from HVSR has been tested by comparing estimates provided by independent methods (modeling or earthquake recordings). The test confirmed the reliability of the microtremor HVSR for assessing the resonance frequencies of the examined sites.

Description: Published

Description: 1821-1838

Description: 4.1. Metodologie sismologiche per l'ingegneria sismica

Description: JCR Journal

Description: open

Description: Mt. Etna is permanently active requiring a continuous data acquisition a multidisciplinary monitoring system where huge data masses accumulate and pose severe difficulties of interpretation. Therefore the INGV staff has developed a number of software tools for data mining, aiming at identifying structures in the data which can be related to the volcanic activity and furnish criteria for the definition of alert systems. We tackle the problem by applying methods of clustering and classification. We identify data groups by defining a measure of similarity or distance. Data groups may assume various shapes, once forming convex clouds once complex concave bodies. The tool “KKAanalysis” is a basket of clustering methods and forms the backbone of the tremor-based automatic alarm system of INGV-OE. It exploits both SOM and Fuzzy Clustering. Besides seismic data the concept has been applied to petrochemic data as well as in a combined analysis of gas-emission data and seismic data. The software “DBSCAN” focuses on density-based clustering that allows discovering clusters with arbitrary shape. Here, clusters are defined as dense regions of objects in the data space separated by regions of low density. In DBSCAN a cluster grows guaranteeing that the density within a group of objects exceeds some threshold. In the context of volcano monitoring the method is particularly promising in the recognition of ash particles as they have a rather irregular shape. The “MOTIF” software allows identifying typical wave forms in time series. It overcomes shortages of methods like cross- correlation, which entail a high computational effort. MOTIF on the other hand can recognize non-similarity of two patterns on a small number of data points without going through the whole length of the data vectors. The development includes modules for feature extraction and post-processing verifying the validity of the results obtained by the classifiers.

Description: Published

Description: Nicolosi (Catania, Italy)

Description: 2V. Dinamiche di unrest e scenari pre-eruttivi

Description: open

Description: Timely identification of changes in the state of volcanoes and onset of potentially dangerous eruptive phenomena requires efficacious surveillance methods. In the case of an active volcano like Mt Etna, the continuous background seismic signal called volcanic tremor is of paramount importance. The huge amount of continuously acquired digital data entails the necessity of data reduction and parameter extraction. For this purpose, techniques of automatic analysis of volcanic tremor were applied by INGV for the real time monitoring of this signal. We checked the possibility to identify regimes of volcanic activity based on pattern classification of volcanic tremor. A specific software named “KKAnalysis” was developed. It combines various unsupervised classification methods (Kohonen Maps and fuzzy cluster analysis) and forms the backbone of an automatic alert system at INGV-OE. Besides its near real time application, it can be operated off-line, allowing an efficient a-posteriori processing of data and tuning of the alarm criteria to match specific needs of sensitivity and robustness. An ongoing development of this tool will allow us to include a large number of seismic stations in a multistation-alarm system. The new system will be more robust in case of failure of single sensors, and will achieve a better coverage of the various eruptive craters. In an off-line test, we exploited a dataset covering eight years of seismic records, and analysed the performance of the new system in terms of “trigger timing” and spatial distribution of the stations. Intriguing results were obtained throughout periods of renewal of volcanic activity at Bocca Nuova-Voragine and North East Crater, and in the absence of paroxysmal phenomena at South East Crater and New South East Crater.

Description: Published

Description: Nicolosi (Catania, Italy)

Description: 2V. Dinamiche di unrest e scenari pre-eruttivi

Description: open

Description: A site response experiment was performed in the basin of Città di Castello (a small town in Central Italy) in May 2001. This study is part of a project on the evaluation of seismic hazard in seismogenic areas funded by the Gruppo Nazionale Difesa dai Terremoti (GNDT). The experiment consisted of a dense fixed transect configuration with most of the stations recording in continuous mode, and several ambient noise measurements both in single station and in array configuration spread over the investigated area. The dense transect was composed of 26 seismic stations in a crosswise configuration with a maximum inter-station distance of 250 m. The stations were deployed in the southern part of the basin, from the eastern bedrock outcrop to the western edge, across the town. About 70 earthquakes were recorded during 10 days of deployment, generally low magnitude or regional events. We located 23 earthquakes and 17 of them were located using the waveform similarity approach at 4 stations outside the target area. These 4 stations were part of a dense temporary seismic network involved in a previous experiment of the same project, aimed at performing a high-resolution picture of the local seismicity. Delay analysis on the recorded waveforms allowed us to infer the basin geometry at depth and estimate the S-wave velocity of sediments. Moreover, we evaluated relative site response along the E-W transect by performing a standard spectral ratio. Amplification factors up to 9 are found inside the basin; at frequencies above 5 Hz stations closer to the edges show higher amplification, whereas stations located in the middle of the basin, where the alluvial sediments are thicker (CD11-CD14), show higher amplification below 5 Hz. We considered the average amplification in two frequency bands (1-5 Hz and 5-10 Hz), representative of the resonance frequency for 2-3 storey buildings and 1 storey houses,respectively. Our results suggest that the potential hazard for 2-3 storey buildings is higher in the center of the basin (amplification factor up to 6), and for 1 storey houses is higher at the edges (amplification factor up to 5).

Description: Published

Description: JCR Journal

Description: open

Description: Long-term geochemical monitoring performed in the seismic area of the Umbria-Marche region of Italy (i.e. Central Apennines) has allowed us to create a model of the circulation of fluids and interpret the temporal chemical and isotopic variations of both the thermal springs as well as the gas vents. Coincident with the last seismic crisis, which struck the region in 1997-1998, an enhanced CO2 degassing on a regional scale caused a pH-drop in all the thermal waters as a consequence of CO2 dissolution. Furthermore, much higher 3He/4He isotope ratios pointed to a slight mantle-derived contribution. Radon activity increased to well above the ±2 sinterval of the earlier seismic period, after which it abruptly decreased to very low levels a few days before the occurrence of the single deep-located shock (March 26, 1998, 51 km deep). The anomalous CO2 discharge was closely related to the extensional movement of the normal faults responsible for the Mw 5.7, 6.0 and 5.6 main shocks that characterized the earlier seismic phase. In contrast, a clear compressive sign is recognizable in the transient disappearance of the deep-originating components related to the Mw 5.3, 51 km-deep event that occurred on March 26, 1998. Anomalies were detected concomitantly with the seismicity, although they also occurred after the seismic crisis had terminated. We argue that the observed geochemical anomalies were driven by rock permeability changes induced by crustal deformations, and we describe how, in the absence of any release of elastic energy, the detection of anomalies reveals that a seismogenic process is developing. Indeed, comprehensive, long-term geochemical monitoring can provide new tools allowing us to better understand the development of seismogenesis.

Description: Published

Description: JCR Journal

Description: open

Description: To verify the results of seismic microzoning and to improve techniques, the damage data of past destructive earthquakes is an important key reference. The damage data of the 1923 Kanto, Japan, earthquake in the epicentral region are collected and compiled to produce the most reliable and detailed damage map. The damage map is compared with the results from the existing damage assessment and is used to discuss revision of the site amplification evaluation.

Description: Published

Description: JCR Journal

Description: open

Description: The results of a detailed seismic microzonation study performed at Canazei (Trentino—Northern Italy) are here presented. We investigated the local seismic response of this small village using a Level 3 seismic microzonation, the most accurate according to the Italian Code of Seismic Microzonation. This method consists of gradual steps of knowledge to consider different aspects of the amplification phenomena. A multidisciplinary approach has been performed, including a local geological study, geophysical investigations, geotechnical characterization of lithologies and numerical analyses. The obtained elastic response spectra were compared to the spectra prescribed by the Italian Building Code. Our results show the geologic and geophysical subsoil heterogeneities, responsible for different local seismic responses in terms of acceleration spectra and amplification factors.

Description: Published

Description: 1085-1089

Description: 3T. Pericolosità sismica e contributo alla definizione del rischio

Description: reserved

Description: An analytical approach to estimate the relative contribution of the fluid pressure and tectonic stress in hydrothermal/ volcanic areas is proposed assuming a Coulomb criterion of failure. The analytical procedure requires the coefficient of internal friction, cohesion, rock density, and thickness of overburden to be known from geological data. In addition, the orientation of the principal stress axes and the stress ratio must be determined from the inversion of fault-slip or seismic data (focal mechanisms). At first, the stress magnitude is calculated assuming that faulting occurs in 'dry' conditions (fluid pressure=0). In a second step, the fluid pressure is introduced performing a grid search over the orientation of 1) fault planes that slip by shear failure or 2) cracks that open under different values of fluid pressure and calculating the consistency with the observed fault planes (i.e. strike and dip of faults, cracks, nodal planes from focal mechanisms). The analytical method is applied using fault-slip data from the Solfatara volcano (Campi Flegrei, Italy) and seismic data (focal mechanisms) from the Vesuvius volcano (Italy). In these areas, the fluid pressure required to activate faults (shear fractures) and cracks (open fractures) is calculated. At Solfatara, the ratio between the fluid pressure and the vertical stress ?is very low for faults ( ?=0.16) and relatively high for cracks ( ?=0.5). At Vesuvius, ?=0.6. Limits and uncertainties of the method are also discussed.

Description: Published

Description: JCR Journal

Description: open

Description: Volcanic eruptions are unsteady multiphase phenomena, which encompass many inter-related processes across the whole range of scales from molecular and microscopic to macroscopic, synoptic and global. We provide an overview of recent advances in numerical modelling of volcanic effects, from conduit and eruption column processes to those on the Earth s climate. Conduit flow models examine ascent dynamics and multiphase processes like fragmentation, chemical reactions and mass transfer below the Earth surface. Other models simulate atmospheric dispersal of the erupted gas-particle mixture, focusing on rapid processes occurring in the jet, the lower convective regions, and pyroclastic density currents. The ascending eruption column and intrusive gravity current generated by it, as well as sedimentation and ash dispersal from those flows in the immediate environment of the volcano are examined with modular and generic models. These apply simplifications to the equations describing the system depending on the specific focus of scrutiny. The atmospheric dispersion of volcanic clouds is simulated by ash tracking models. These are inadequate for the first hours of spreading in many cases but focus on long-range prediction of ash location to prevent hazardous aircraft - ash encounters. The climate impact is investigated with global models. All processes and effects of explosive eruptions cannot be simulated by a single model, due to the complexity and hugely contrasting spatial and temporal scales involved. There is now the opportunity to establish a closer integration between different models and to develop the first comprehensive description of explosive eruptions and of their effects on the ground, in the atmosphere, and on the global climate.

Description: Published

Description: JCR Journal

Description: open

Description: A 2D finite elements study was carried out to analyse the effects caused by dike intrusion inside a heterogeneous medium and with a realistic topography of Mt. Etna volcano. Firstly, the method (dimension domain, elements type) was calibrated using plane strain models in elastic half-spaces; the results were compared with those obtained from analytical dislocation models. Then the effects caused both by the topographic variations and the presence of multi-layered medium on the surface, were studied. In particular, an application was then considered to Mt. Etna by taking into account the real topography and the stratification deduced from seismic tomography. In these conditions, the effects expected by the dike, employed to model the 2001 eruption under simple elastic half-space medium conditions, were computed, showing that topography is extremely important, at least in the near field.

Description: Published

Description: JCR Journal

Description: open

Description: Vesuvius, dominating the densely-populated Neapolitan area, is one of the most dangerous volcanoes in the World. Its destructive power derives from energetic subplinian and plinian eruptions, such as the one which occurred in 79 A.D. Generally such large-scale events follow a long period of quiescence; a behaviour interpreted as the gradual build-up of magma volumes between periods of major activity. After the 1631 subplinian eruption until the last 1944 A.D. eruption, it experienced an almost continuous and less energetic explosive/effusive activity. The erupted magmas are characterized by undersaturated potassic to ultrapotassic nature, and compositional and Sr-isotopic variability. Furthermore geobarometric studies indicate two different crystallization depths located at 4 and 〉11 km, respectively. According to most of the recent literature, the eruptions were triggered by the injection in a shallower magma chamber, of isotopically distinct magma batches derived from heterogeneous mantle source(s) and/or contamination processes occurred within the deep reservoir. In our review of petrochemical data, we consider the period between the 3550 years BP plinian eruption and the 472 A.D. sub-plinian eruption, which includes 79 A.D. event, and the most recent period of activity which started in 1631 A.D. and lasted up to the 1944 A.D. eruption, characterized by a near continuous effusive/explosive activity. For both periods we identify a correlation between Sr-isotopical features of magmas and their crystallization depth. In particular, we show that pyroxenes have Sr-isotopic ratios lower than 0.7074 and an equilibrium crystallization depth of 22-11 km. Moreover feldspars have higher 87Sr/86Sr values (0.7075-7) and an equilibrium crystallization depth of about 4 km. Therefore the most radiogenic magmas did not derive from a deeper reservoir but their higher Sr-isotopic ratios have been acquired at a shallower depth likely by crustal contamination during magma evolution. In contrast, the lower Sr-isotope compositions characterise the less contaminated magmas coming from deeper crustal levels. On the basis of this evidence, the temporal Sr-isotopical variation of magma which erupted in the 1631-1944 A.D. period probably derives from the progressive withdrawal of the shallow magma chamber, which was completely empty before the 1805-1944 A.D. period of volcanism. Therefore the effusive and explosive events of the most recent 1805-1944 A.D. period were fed directly by the deep reservoir located at a depth exceding 11 km.

Description: Published

Description: JCR Journal

Description: open

Description: This study presents results of ambient noise measurements from temporary single station and small-scale array deployments in the northeast of Basle. H/V spectral ratios were determined along various profiles crossing the eastern masterfault of the Rhine Rift Valley and the adjacent sedimentary rift fills. The fundamental H/V peak frequencies are decreasing along the profile towards the eastern direction being consistent with the dip of the tertiary sediments within the rift. Using existing empirical relationships between H/V frequency peaks and the depth of the dominant seismic contrast, derived on basis of the ?/4-resonance hypothesis and a power law depth dependence of the S-wave velocity, we obtain thicknesses of the rift fill from about 155 m in the west to 280 m in the east. This is in agreement with previous studies. The array analysis of the ambient noise wavefield yielded a stable dispersion relation consistent with Rayleigh wave propagation velocities. We conclude that a significant amount of surface waves is contained in the observed wavefield. The computed ellipticity for fundamental mode Rayleigh waves for the velocity depth models used for the estimation of the sediment thicknesses is in agreement with the observed H/V spectra over a large frequency band.

Description: Published

Description: JCR Journal

Description: open

Description: Terrestrial heat flow density, q, is inversely correlated with the age, t, of tectono-magmatic activity in the Earth's crust (Polyak and Smirnov, 1966; etc.). «Heat flow-age dependence» indicates unknown temporal heat sources in the interior considered a priori as the mantle-derived diapirs. The validity of this hypothesis is demonstrated by studying the helium isotope ratio, 3He/4He = R, in subsurface fluids. This study discovered the positive correlation between the regionally averaged (background) estimations of R- and q-values (Polyak et al., 1979a). Such a correlation manifests itself in both pan-regional scales (Norhtern Eurasia) and separate regions, e.g., Japan (Sano et al., 1982), Eger Graben (Polyak et al., 1985) Eastern China rifts (Du, 1992), Southern Italy (Italiano et al., 2000), and elsewhere. The R-q relation indicates a coupled heat and mass transfer from the mantle into the crust. From considerations of heat-mass budget this transfer can be provided by the flux consisting of silicate matter rather than He or other volatiles. This conclusion is confirmed by the correlation between 3He/ 4He and 87Sr/86Sr ratios in the products of the volcanic and hydrothermal activity in Italy (Polyak et al., 1979b; Parello et al., 2000) and other places. Migration of any substance through geotemperature field transports thermal energy accumulated within this substance, i.e. represents heat and mass transfer. Therefore, only the coupled analysis of both material and energy aspects of this transfer makes it possible to characterise the process adequately and to decipher an origin of terrestrial heat flow observed in upper parts of the earth crust. An attempt of such kind is made in this paper.

Description: Published

Description: JCR Journal

Description: open

Description: Newly acquired high-resolution, low-altitude aeromagnetic data over Vulcano Island and Southwestern Lipari in the Southern Tyrrhenian Sea resolve the major volcanic features in the area associated with the past and present activity. The magnetic character changes in amplitude and frequency from south-east to north-west. The Primordial Vulcano, the Lentia Complex, the Piano Caldera units, the Fossa Caldera deposits, and the currently active La Fossa cone and Vulcanello represent the main volcanic phases on Vulcano Island. They show a distinct magnetic anomaly pattern, whereas prior to this survey, no magnetic signatures of these features were found.

Description: Published

Description: JCR Journal

Description: open

Description: In order to obtain information on the hydrological signature of rivers during and after heavy rain events, small catchment areas are selected as experimental sites. Hydrograph separations based on environmental tracers are performed. Natural isotopic tracers such as 18O, 2H and particularly 222Rn may help to distinguish the components dominating the outflow, particularly of 'pre-event waters', 'event waters' and 'post-event waters'. Even with moderate concentrations in groundwater, radon can be a very sensitive indicator of groundwater input into rivers. The selected microbasin under investigation is situated in the western part of Luxembourg and belongs to the Attert River catchment. At chosen points at the basin's outflow radon detectors continuously measure radon activity in water. The radon monitors are installed together with high precision thermometers, conductivity meters, flow meters and automatic water samplers for chemical analysis. Besides the continuous measurements, grab water samples are taken at different locations along the stream, most of them during periods of heavy rain events. Presented are the results of a one year measurement campaign. During the dry season i.e. during more or less continuous discharge conditions, the observed mean values do not show substantial variations and can be used as reference values. Fluctuations of the measured data during rain events are discussed and the interplay between the different parameters analysed.

Description: Published

Description: JCR Journal

Description: open

Description: Destructive volcaniclastic flows are among the most recurrent and dangerous natural phenomena in volcanic areas. They can originate not only during or shortly after an eruption (syn-eruptive) but also during a period of volcanic quiescence (inter-eruptive), when heavy and/or persistent rains remobilize loose pyroclastic deposits. The area in Italy most prone to such flows is that of the Apennine Mountains bordering the southern Campania Plain. These steep slopes are covered by pyroclastic material of variable thickness (a few cm to several m) derived from the explosive activity of the Somma-Vesuvius and Campi Flegrei volcanoes a few tens of kilometers to the west. The largest and most recent devastating event occurred on May 5, 1998, causing the death of more than 150 people and considerable damage to villages at the foot of the Apennine Mountains. This tragic event was only the most recent of a number of volcaniclastic flows affecting the area in both historical and prehistoric times. Historical accounts report that more than 500 events have occurred in the last five centuries and that more than half of these occurred in the last 100 years, causing hundreds of deaths. In order to improve volcaniclastic flow hazard zonation and risk mitigation in the study area, we produced a zonation map that identifies the drainage basins potentially prone to disruption. This map was obtained by combining morphological characteristics (concavity and basin shape factor) and the mean slope distribution of drainage basins derived from a digital elevation model with a 10-m resolution. These parameters allowed for the classification of 1,069 drainage basins, which have been grouped into four different classes of proneness to disruption: low, moderate, high and very high. The map compiled in a GIS environment, as well as the linked database, can be rapidly queried.

Description: Published

Description: 371-387

Description: 3.5. Geologia e storia dei vulcani ed evoluzione dei magmi

Description: 4.3. TTC - Scenari di pericolosità vulcanica

Description: JCR Journal

Description: reserved

Description: We describe analytical details and uncertainty evaluation of a simple technique for the measurement of the carbon isotopic composition of CO2 in volcanic plumes. Data collected at Solfatara and Vulcano, where plumes are fed by fumaroles which are accessible for direct sampling, were first used to validate the technique. For both volcanoes, the plume-derived carbon isotopic compositions are in good agreement with the fumarolic compositions, thus providing confidence on the method, and allowing its application at volcanoes where the volcanic component is inaccessible to direct sampling. As a notable example, we applied the same method to Mount Etna where we derived a δ13C of volcanic CO2 between −0.9 ± 0.27‰ and −1.41 ± 0.27‰ (Bocca Nuova and Voragine craters). The comparison of our measurements to data reported in previous work highlights a temporal trend of systematic increase of δ13C values of Etna CO2 from ~ −4‰, in the 1970’s and the 1980’s, to ~ −1‰ at the present time (2009). This shift toward more positive δ13C values matches a concurrent change in magma composition and an increase in the eruption frequency and energy. We discuss such variations in terms of two possible processes: magma carbonate assimilation and carbon isotopic fractionation due to magma degassing along the Etna plumbing system. Finally, our results highlight potential of systematic measurements of the carbon isotopic composition of the CO2 emitted by volcanic plumes for a better understanding of volcanic processes and for improved surveillance of volcanic activity.

Description: In press

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: 2.4. TTC - Laboratori di geochimica dei fluidi

Description: JCR Journal

Description: reserved

Description: Etna’s 2001 basaltic lava flow provided a good example of the distal flow segment between the flow front and stable channel, across which the flow evolves from channel-contained to dispersed. This zone was mapped with meter precision using LIDAR data collected during 2004 and 2005. These data, supported by field mapping, show that the flow front comprised eight lobes each 10 to 20 m high. The flow front appears to have advanced not as a single unit, but as a series of lobes moving forward one lobe at a time. Primary lobes were centered on the channel axis and marginal lobes were off-axis. The lobes advanced as breakouts of low-yield-strength lava from the flow core of the stalled flow front. Marginal lobes were abandoned and contributed to marginal levees flanking the transitional channel. For Etna’s 2001 flow, the transitional channel is 140 m wide, 700 m long and fed a 240-m-long zone of dispersed flow; the change from stable to transitional channel occurred at a major reduction in slope. Above this, the stable channel is 5.2 km long, 55 to 105 m wide and bounded by 15- to 25-m-high levees, and the stable channel is located over a previous channel. In a final stage of activity, lava ponding at the break-in-slope that marks the terminus of the stable channel put pressure on the eastern levee, causing it to fail. Liberated lava then fed a final break-out to the east. Similar flow front-features occur at other volcanoes, indicating that similar processes are characteristic of dispersed flow zones.

Description: Published

Description: 119-127

Description: 1.10. TTC - Telerilevamento

Description: 3.5. Geologia e storia dei vulcani ed evoluzione dei magmi

Description: 3.6. Fisica del vulcanismo

Description: JCR Journal

Description: reserved

Description: The aim of this study is the sharing of waveforms recorded by several Istituto Nazionale di Geofisica e Vulcanologia (INGV) temporary stations (managed by the Milan-Pavia section; INGV MI-PV). These stations were installed after the April 6, 2009, Mw 6.3, L'Aquila earthquake (central Italy). The work synthesizes the activities conducted in the field by the INGV MI-PV working group over the three months following the mainshock. The field activities were developed in four different phases that were defined according to their time periods. Starting from April 7, 2009, for the first phase, the temporary stations were installed in correspondence with the more damaged areas. The scope was to record the strongest aftershocks in the days that followed the mainshock. In this phase, the stations were composed of a sixcomponent acquisition system that was coupled with both a weak-motion and a strong-motion sensor. After the first month, the last three phases of installation investigated the seismic responses of sites located in the epicentral area, involving villages within a radius of about 20 km from the epicenter of the April 6 mainshock. In this way, over four specific time-period phases, the stations were installed in sites with different lithological and geomorphological conditions. The instruments worked from April 7 to July 14, 2009; in this period, 9,155 aftershocks (134,262 accelerometric waveforms and 133,242 velocimetric waveforms), with ML ≤5.3 were recorded. This study describes the dataset of these earthquake waveforms recorded with both velocity and acceleration transducers. Selected waveforms are available through ftp://ftp.mi.ingv.it/download/RAIS-TS_rel01/, with their corresponding information concerning instrumental characteristics, installation sites, and earthquakes recorded.

Description: Published

Description: 101-113

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: JCR Journal

Description: open

Description: In this work we present and discuss the results of ambient seismic noise analyses computed at four sites where seismic stations, managed by the INGV (Italian Institute for Geophysics and Vulcanology) and the DPC (Italian Department of Civil Protection), are installed inside buildings. The experiments were performed considering different types of installation: sensor located at the bottom of a school, directly installed on rock (case 1); sensor located at the bottom of a medieval fortress, built on an isolate hill, directly installed on rock (case 2); sensor installed on the foundations of a medieval fortress, built on an isolate hill (case 3); sensor installed on the foundations of a school, built on alluvial deposits (case 4). Since recent works proposed the use of spectral ratio techniques to study the dynamic characterization of buildings, ambient seismic-noise measurements were performed for each site close to the stations (at the base of the structures), at the top of the structures and outside the buildings. In order to check the source of vibrations both horizontal to vertical spectral ratio (HVNR) and standard spectral ratio (SSR) techniques were applied. For all stations the results from ambient seismic noise were compared to those obtained from earthquakes (HVSR). In order to detect preferential directions of amplification, for each site average HVNRs and HVSRs were computed considering one azimuth for each set of 5°. We obtain different results for different types of installation: in cases 1 and 2, where the sensors are directly installed on rock, the vibrations of the structure do not affect the noise measures performed close to the stations, which show flat HVNR in the whole frequency range: in both cases the eigenfrequency of the building is given by the HVNR calculated from the measures performed at the top of the structure. In cases 3 and 4, where the sensors are installed on the foundations of the considered structures, both the amplification peaks between 5 and 9 Hz (case 3) and between 5.5 and 7 Hz (case 4) include the contribution of the free oscillations of the buildings. In particular, in case 4, HVNRs performed outside building highlight possible soil–structure resonance effects in case of an earthquake.

Description: Published

Description: 723-738

Description: 4.1. Metodologie sismologiche per l'ingegneria sismica

Description: JCR Journal

Description: open

Description: The necessity of a dense network in Northern Italy started from the lack of available data after the occurrence of the 24th November 2004, Ml 5.2, Salò earthquake. Since 2006, many efforts have been made by the INGV (Italian National Institute for Geophysic and Vulcanology), Department of Milano-Pavia (hereinafter INGV MI-PV), to improve the strong-motion monitoring of the Northern Italy regions. This activity led to the installation of a strong-motion network composed by 20 accelerometers, 4 coupled with 20-bits Lennartz Mars88 recorders, 12 coupled with 24-bits Reftek 130 recorders and 4 coupled with 24-bits Gaia2 recorders. The network allow us to reduce, in the area under study, the average inter-distances between strong-motion stations from about 40 km (at November 2004) to 15 km. At present the network includes nine 6-channels stations where velocity sensors work together the strong-motion ones. The data transmission is assured by modem-gsm, with the exception of four stations that send data in real time through a TCP/IP protocol. In order to evaluate different site responses, the stations have been installed both in free field and near (or inside) public buildings, located in the center of small villages. From June 2006 to December 2008 a dataset of 94 events with local magnitude range from 0.7 to 5.1 has been collected. An ad hoc data-processing system have been created in order to provide, after each recorded event, engineering parameters such as peak ground acceleration (PGA) and velocity (PGV), response spectra (SA and PSV), Arias and Housner intensities. Data dissemination is achieved through the web site http://rais.mi.ingv.it, while the waveforms are distributed through the Italian strong motion database (http://itaca.mi.ingv.it).

Description: Published

Description: 1091-1104

Description: 1.1. TTC - Monitoraggio sismico del territorio nazionale

Description: JCR Journal

Description: open

Description: Natural precipitation and water samples from passive devices were collected at Mt. Vesuvius and Vulcano Island, Italy, during the period 2004–2006, in order to investigate its possible interactions with fumarolic gases. Evidence of chemical reactions between fumarolic fluids and rain samples before and after its deposition into the sampling devices was found at Vulcano Island. Very low pH values (down to 2.5) and significant amounts of chlorine and sulfate (up to 22 mEq/l) were measured at sampling points located close to the fumarolic field. In contrast, anthropogenic contributions and/or dissolution of aerosols (both maritime and continental) influence the chemistry of rainwaters at Mt. Vesuvius, which show inter-annual variations that are highly consistent with those recorded at the coastal site at Vulcano Island. Chemistry of waters directly exposed to fumarolic fluids may then give useful information about its temporal evolution, holding the signal of the ‘‘maximum’’ chemical event occurred in the meanwhile. In addition, the observation of the health status of vegetation colonizing the immediate surroundings of the fumarolic fields, due to its strong dependence on the interactions with these fluids, may work as a possible biomarker of volcanic activity.

Description: Published

Description: 159-171

Description: 1.2. TTC - Sorveglianza geochimica delle aree vulcaniche attive

Description: JCR Journal

Description: restricted