ALBERT

Description: Background information and exercises are provided to: (1) establish or expand understanding of the concepts, methods, and terminology of computer processing of image producing data; (2) develop insight into the advantages of computer based image processing compared with the photointerpretation approach for processing, classifying, interpreting, and applying remote sensing data; (3) foster a broad perspective on the principal of the main techniques for image enhancement, pattern recognition, and thematic classification; (4) appreciate the pros and cons of batch and interactive modes of image analysis; (5) examine and evaluate some specific computer generated products for subscenes in Pennsylvania and New Jersey; and (6) interrelate these particular examples of output with more theoretical explanations of computer processing strategies and procedures.

Description: Transpiration cooling is treated and then full coverage discrete hole injection for three injection orientations. Spacings with pitch to diameter ratios of 5 and 10 are discussed. The array is staggered, with the transverse pitch and the streamwise pitch the same. Results are presented in terms of the Stanton number using the heat transfer coefficient defined in terms of the difference between the wall temperature and the free stream temperature. Two values of Stanton number are provided for each situation: one with the injectant at wall temperature, and the other with the injectant at free stream temperature. These two values are equivalent to knowing the heat transfer coefficient and the adiabatic effectiveness. The heat transfer coefficient thus defined is used with the actual wall temperature to and the actual gas temperature to calculate the heat load. The principle of superposition thus invoked is valid exactly when the governing equations are linear.

Description: Images characteristics of geographic regions other than the northeastern part of the United States are presented for interpretation. Pre- and post-eruption imagery of Mt. St. Helens volcano serves to demonstrate the advantages of thermal infrared sensing, and the potential for developing a timely, decision oriented thematic map to be used in solving drought-related problems in Upper Volta is examined to show the applicability of satellite remote sensing in all geographic areas.

Description: The 1980 eruptions of Mount St. Helens in southeast Washington resulted in a pronounced effect on the surface and ground water resources of the state. In response to the volcanic activity, the U.S. Geological Survey intensified statewide surface and ground water sampling programs to determine the nature and magnitude of the volcanic-induced variations. Streams to the east of Mount St. Helens received the major ash fallout. Chemical effects were best noted in smaller streams sampled 60 to 70 miles northeast of Mount St. Helens. The chemical variations observed were pronounced but short lived. Sulfate and chloride increases in anionic composition were prevalent immediately following the eruption; however, the original bicarbonate predominance was again attained within several days. Suspended iron and aluminum concentrations were similarly elevated during the period of greatest ash deposition (highest turbidity); however, the dissolved concentrations remained relatively constant. Depressions of pH were minor and short lived. Streams draining to the south, tributaries to the Columbia river, showed little observable changes in water chemistry. Streams draining to the west (Toutle river and its tributaries) were compositionally affected by the various volcanic activities. Chloride and sulfate anion percentage exceeded the bicarbonate percentage up to one month following the eruption period. Streams and lakes sampled in the immediate vicinity of Mount St. Helens, in addition to trace metals, contained organic compounds derived from decomposing wood buried in the debris deposits. This organic material may constitute a significant source of organic compounds to surface and ground water for some time to come.

Description: The benefits-to-cost ratio of satellite remote sensing, both as a substitute for conventional methods of monitoring and assessing resources, and as a supplement to these methods is examined using a model which analyzes the cost of aerial photography versus satellite scanner for producing and interpreting an image of the Earth's surface sized to LANDSAT dimensions. Examples of cost savings are tabulated for ground surveys, aerial photos, and LANDSAT. Possible additional benefits from LANDSAT D are assessed. The way in which satellites fit into more comprehensive models for resources management is discussed. It is shown that remote sensing is but one essential component in a complex system that aggregates technical. Socioeconomics, political, cultural, and other factors in the human decision process.

Description: Computer processing facilitates extraction of information from every pixel by executing a variety of functional operations, called processed algorithms, in general or specialized routines. The best results are obtained when data from more than one multispectral band are used together. Multivariate tatistical analysis, computer tape characteristics, processing modes, and a choice of systems (batch or interactive) are discussed. The major operations in computer processing elaborated include: preprocessing, enhancement, effects of rationing, and classification. Techniques for multisource data correlation are considered with emphasis on geobased systems.

Description: Learning objectives include: (1) developing an understanding of the implications of the term "near surface observations"; (2) associating the appearance of large ground features as seen in satellite imagery with their appearance as seen from the ground; (3) grasping criteria and procedures for selecting training sites on the ground for use in supervised classification; (4) running through an example of training site selection; (5) becoming familiar with several methods of accuracy assessment; (6) becoming aware of the approach and value of making supporting measurements of the spectral and physical properties of materials on the ground and from aircraft; (7) taking note of the different types of instruments used in making specific ground measurements; and (8) appreciating the rationale underlying laboratory and field studies on or near the Earth's surface for the purpose of developing new sensor systems.

Description: Learning objectives include: (1) developing a facility for applying conventional techniques of photointerpretation to small scale (satellite) imager; (2) promoting the ability to locate, identify, and interpret small natural and man made surface features in a LANDSAT image; (3) using supporting imagery, such as aerial and space photography, to conduct specific applications analyses; (4) learning to apply change detection techniques to recognize and explain transient and temporal events in individual or seasonal imagery; (5) producing photointerpretation maps that define major surface units, themes, or classes; (6) classifying or analyzing a scene for specific discipline applications in geology, agriculture, forestry, hyrology, coastal wetlands, and environmental pollution; and (7) evaluating both advantages and shortcomings in relying on the photointerpretive approach (rather than computer based analytical approach) for extracting information from LANDSAT data.

Description: Activities are provided for: (1) developing insight into the way in which the LANDSAT MSS produces multispectral data; (2) promoting understanding of what a "pixel" means in a LANDSAT image and the implications of the term "mixed pixel"; (3) explaining the concept of spectral signatures; (4) deriving a simple signature for a class or feature by analysis: of the four band images; (5) understanding the production of false color composites; (6) appreciating the use of color additive techniques; (7) preparing Diazo images; and (8) making quick visual identifications of major land cover types by their characteristic gray tones or colors in LANDSAT images.

Description: Learning objectives of the activities provided include: (1) reading the annotation of a LANDSAT image; (2) becoming acquainted with the characteristics of 1:1,000,000 scale transparencies and prints of MSS images; (3) noting the general information visible in LANDSAT photo products; (4) observing changes of appearance of any ground feature or class in the black and white images made from the four MSS bands and the characteristic color of each class in color composites; (5) determining the degree to which a LANDSAT image meets map accuracy standards and can be fitted to map projections; (6) assessing the effects of LANDSAT enlargements and scale changes and of the limitations of satellite resolution relative to aerial photos; (7) observing the influence of time of acquisition (season) on a scene; (8) getting a feel for image quality as dependent on processing and photoreproduction; (9) appreciating the characteristics of the RBV and thermal band imagery obtained from LANDSAT-3; and (10) becoming familiar with certain attributes of adjacent LANDSAT images which permit them to be joined in mosaics and to be viewed in stereo.

Description: The primary LANDSAT mission and the system requirements are summarized and pertinent parameters of the spacecraft, its orbit, and payload are tabulated. The history acquisition to entry into the archives for storage and product generation and dissemination is recounted. The LANDSAT D data handling plan is discussed showing requirements for both the MSS CCT and the thematic mapper CCT.

Description: The term remote sensing is defined as well as ideas such as class, pattern, feature, pattern recognition, feature extraction, and theme. The electromagnetic spectrum is examined especially those wavelength regions available to remote sensing. Relevant energy and wave propagation laws are discussed and the characteristics of emitted and reflected radiation and their detection are investigated. The identification of classes by their spectral signatures, the multispectral approach, and the principal types of sensors and platforms used in remote sensing are also considered.

Description: Analysis techniques for three aspects of the performance of the NASA/MSFC 32 meter drop tube are considered. Heat loss through the support wire in a pendant drop sample, temperature history of a drop falling through the drop tube when the tube is filled with helium gas at various pressures, and drag and resulting g-levels experienced by a drop falling through the tube when the tube is filled with helium gas at various pressures are addressed. The developed methods apply to systems with sufficiently small Knudsen numbers for which continuum theory may be applied. Sample results are presented, using niobium drops, to indicate the magnitudes of the effects. Helium gas at one atmosphere pressure can approximately double the amount of possible undercooling but it results in an apparent gravity levels of up to 0.1 g.

Description: The history of remote sensing is reviewed and the scope and versatility of the several remote sensing systems already in orbit are discussed, especially those with sensors operating in other EM spectral modes. The multisensor approach is examined by interrelating LANDSAT observations with data from other satellite systems. The basic principles and practices underlying the use of thermal infrared and radar sensors are explored and the types of observations and interpretations emanating from the Nimbus, Heat Capacity Mapping Mission, and SEASAT programs are examined. Approved or proposed Earth resources oriented missions for the 1980's previewed include LANDSAT D, Stereosat, Gravsat, the French satellite SPOT-1, and multimission modular spacecraft launched from space shuttle. The pushbroom imager, the linear array pushbroom radiometer, the multispectral linear array, and the operational LANDSAT observing system, to be designed the LANDSAT-E series are also envisioned for this decade.

Description: The use of computer aided classification of LANDSAT data in developing water quality plans for New Jersey watersheds is used to exemplify how a state natural resource management program benefits from satellite imagery. The transition of a research and development system into an operational remote sensing system to help decision makers is demonstrated. Nontechnial issues that can assist (or hinder) an agency in adopting a new technology are examined. The progress of LANDSAT use by state government from the earliest stage of curiosity through to incorporation in actual state planning methods is charted. Potential applications of LANDSAT data to real information needs and solutions to management problems are examined. The problems and mistakes that occurred in using LANDSAT data in the past are discussed as well as the ways by which these problems were overcome.

Description: Information and activities are provided to: (1) enhance the ability to distinguish between a Geographic Information System (GIS) and a data management system; (2) develop understanding of spatial data handling by conventional methods versus the automated approach; (3) promote awareness of GIS design and capabilities; (4) foster understanding of the concepts and problems of data base development and management; (5) facilitate recognition of how a computerized GIS can model conditions in the present "real world" to project conditions in the future; and (6) appreciate the utility of integrating LANDSAT and other remotely sensed data into the GIS.

Description: This is a review of the influence of convection on the growth of crystals from solution. The growth rate is increased by convection up to the point where interface kinetics becomes rate controlling. Compositional inhomogeneity and morphological instability (inclusion formation) are probably worse for gentle convection than for either no convection or for vigorous stirring. Stirring, particularly of crystal suspensions, can cause an orders of magnitude increase in the rate of formation of new crystals. This is called 'secondary nucleation'.

Description: A multistage sampling procedure using image processing, geographical information systems, and analytical photogrammetry is presented which can be used to guide the collection of representative, high-resolution spectra and discrete reflectance targets for future satellite sensors. The procedure is general and can be adapted to characterize areas as small as minor watersheds and as large as multistate regions. Beginning with a user-determined study area, successive reductions in size and spectral variation are performed using image analysis techniques on data from the Multispectral Scanner, orbital and simulated Thematic Mapper, low altitude photography synchronized with the simulator, and associated digital data. An integrated image-based geographical information system supports processing requirements.

Description: A goal of future synthetic aperture radar (SAR) system design is to yield the radiometrically accurate imagery necessary for use in classification problems. To accomplish this, a reliable calibration technique must be developed. Many such techniques have been proposed (e.g., Stiles and Holtzman, 1982); however, until now, none have been tested on spaceborne SAR digital data. In this paper, a method of significantly increasing the reproducibility of several independent Seasat SAR data sets of a test site using an automated correction procedure is described.

Description: The spectral and spatial requirements for remote sensing in the next decade are presented. The requirements presented were obtained through extensive literature research and discussions with leading members of the various remote sensing research communities. In the 0.35-2.5 micron region of the spectrum, numerous bands will be needed at bandwidths as narrow as 10-20 nanometers. There is also growing interest in the thermal infrared (8-14 microns). Spatial resolution (instantaneous field of view) of 5 to 10 meters will be of great benefit to many fields of remote sensing.

Description: Attention is given to the way in which external turbulence affects an initially turbulence-free region in which there is a mean velocity gradient. External turbulence induces irrotational fluctuations in the sheared region which interact with the shear to produce rotational velocity fluctuations and mean Reynolds stresses. Since the actual front between the initial external turbulence and the shear flow is a randomly contorted surface, the turbulence near the front is intermittent, and is presently included in the form of a simple statistical model. In wind tunnel tests, turbulent shear stress was found to grow from zero to significant values in the interaction region. Observed stress magnitude and extent agrees with predictions, and it is concluded that turbulent stresses can be produced by irrotational fluctuations in a region of mean shear.

Description: A liquid, contained in a quarter plane, undergoes steady motion due to thermocapillary forcing on its upper boundary, a free surface separating the liquid from a passive gas. The rigid vertical sidewall has a strip whose temperature is elevated compared with the liquid at infinity. A boudnary-layer analysis is performed that is valid for large Marangoni numbers M and Prandtl numbers P. It is found that the Nusselt number N for the horizontal heat transport satisfies N proportional to min (M to the 1 2/7/power, M to the 1 1/5/power, M to the 1 1/10/power) Generalizations are discussed.

Description: The presence of positive serial correlation (autocorrelation) in remotely sensed data results in an underestimate of the variance-covariance matrix when calculated using contiguous pixels. This underestimate produces an inflation in F statistics. For a set of Thematic Mapper Simulator data (TMS), used to test the ability to discriminate a known geobotanical anomaly from its background, the inflation in F statistics related to serial correlation is between 7 and 70 times. This means that significance tests of means of the spectral bands initially appear to suggest that the anomalous site is very different in spectral reflectance and emittance from its background sites. However, this difference often disappears and is always dramatically reduced when compared to frequency distributions of test statistics produced by the comparison of simulated training sets possessing equal means, but which are composed of autocorrelated observations. Previously announced in STAR as N82-25602

Description: Six flat-disk models made of carbon-carbon and carbon-phenolic materials were launched in an argon-filled track-range facility to test ablation characteristics in a radiation-dominated, massive-blowing environment. The shock standoff distances deduced from the shadowgraphs agree with theoretical predictions during the earlier portion of the flight, while the wall temperatures determined by the image-converter photographs agree with predictions during the later portion. The measured surface recessions exceed the calculated values by about 60 percent for carbon-phenolic and 30 percent for carbon-carbon. The discrepancies are attributed to spallation. The measured char thicknesses agree with theoretical predictions.

Description: The results of modifications in continuation methods applied to obtain solutions to the Navier-Stokes systems of equations for incompressible, two-dimensional, steady flows are reported. It is shown that parameter continuation permits prediction of accurate, initial estimates for iterative processing of nonlinear finite difference and finite element equations of motions. The new parameter steps are derived from values of the preceding parameter steps. The accuracy of the estimates is ensured with appropriate choices of the step size. The continuation predictor/iterative corrector is demonstrated to trace the branches of parameter space along which steady flow states are found, and techniques are available for tracing multiply branching paths. The techniques are applied to solving the Navier-Stokes equations for flow through a rotating square channel, the formation of a falling liquid curtain, and gyrostatic equilibria of rotating cylindrical drops.

Description: The four-point, centered implicit scheme that is extensively used in open channel flow simulation is shown to be applicable to rapid and slow pressure transient problems in conduits with nearly single phase and two-phase flows. It is only necessary to choose the proper weighting factor value, theta, of the Courant number. For rapid pressure transients such as waterhammer, the implicit method can yield reasonable results with limited numerical dispersion and attenuation if theta is only slightly greater than the critical value of 0.5. For slower pressure gradients in single and two-phase flows, reasonable numerical solutions may be achieved for Courant number values as high as 20.

Description: A complete automatic unsupervised classification approach has been developed to estimate the proportion of corn, soybeans, and other crops in a Landsat 5-by-6-nanometer segment. The technique involves extracting crop growth variables that are predictable from agromet models, it provides a signature extension not possible before. The technique has been applied in 3 years (1978-1980) for 56 segments and shows neither a year-to-year effect nor any geographic effect. The results to date are considered far better than those obtainable from any other currently available technique. Nontheless, the technique can be improved to reduce the bias.

Description: Since NASA's program of research concerning remote sensing was initiated in the 1960s, one of its major objectives has been to advance the state-of-the-art in machine processing of satellite acquired multispectral data. Possibilities have been studied regarding a use of these data to identify type, to monitor condition, and to estimate the ontogenetic stage of cultural vegetation. The present investigation provides a review of the state-of-the-art of the technology used to make remote sensing crop production estimates in foreign regions. Attention is given to Landsat data acquisition, aspects of registration and preprocessing, questions of data transformation, data modeling, proportion estimation, labeling, development stage models, crop condition models, and an outlook regarding future developments.

Description: The improved spatial resolution of the new earth resources satellites will increase the need for effective utilization of spatial information in machine processing of remotely sensed data. One promising technique is scene segmentation by region growing. Region growing can use spatial information in two ways: only spatially adjacent regions merge together, and merging criteria can be based on region-wide spatial features. A simple region growing approach is described in which the similarity criterion is based on region mean and variance (a simple spatial feature). An effective way to implement region growing for remote sensing is as an iterative parallel process on a large parallel processor. A straightforward parallel pixel-based implementation of the algorithm is explored and its efficiency is compared with sequential pixel-based, sequential region-based, and parallel region-based implementations. Experimental results from on aircraft scanner data set are presented, as is a discussioon of proposed improvements to the segmentation algorithm.

Description: The scientific instruments comprising the OSTA-1 package flown on the second Shuttle mission (November 12-14, 1981) are listed, and the Shuttle Imaging Radar (SIR-A) experiments are examined in detail: SIR-A operated for 8 h and obtained images covering more than 10 million sq km at 40-m resolution. The images were recorded on photographic film and processed in holographic form at JPL, and data for Southern Europe and parts of Africa were distributed to French scientists by the Groupement pour le Developpement de la Teledetection Aerospatiale. The main areas of research were environmental studies and geology, and the SIR-A images were used in combination with aerial photography, thematic maps, and Landsat images. The technical specifications of the SIR-B radar planned for STS-17 in 1984 are compared with those of SIR-A and Seasat SAR in tables.

Description: This paper examines, both theoretically and experimentally, the effect produced by irrotational fluctuations, associated with a nearby turbulent field, in a region where the turbulence is initially very low but where there is a mean shear. Calculations are based on rapid distortion theory and experiments use linearized hot wire anemometers in an open circuit wind tunnel. Turbulent shear stress is observed to grow from zero to significant values in the interaction region. The magnitude and extent of this observed shear stress agree reasonably well with predictions of the analysis, when intermittency effects are included. It is concluded that turbulent stresses can be produced by irrotational fluctuations in a region of mean shear and that this effect can be estimated using rapid distortion theory if the overall strain ratio is not large.

Description: The use of remote sensing in resource exploration is reviewed, with emphasis placed on new developments in high spectral resolution remote-sensing techniques for mineralogic and vegetation mapping. Topics discussed include aerial photography and satellite remote sensing, concepts and principles of spectral data collection, spectral properties of rocks and minerals, spectral properties of vegetation, and botanical aspects of geochemical stress. The discussion also covers applications of Landsat multispectral scanner data to lithologic and geobotanic studies and the future development of data acquisition and data interpretation techniques.

Description: In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Description: A revised version of Dodge's split-velocity method for numerical calculation of compressible duct flow was developed. The revision incorporates balancing of mass flow rates on each marching step in order to maintain front-to-back continuity during the calculation. The (checkerboard) zebra algorithm is applied to solution of the three dimensional continuity equation in conservative form. A second-order A-stable linear multistep method is employed in effecting a marching solution of the parabolized momentum equations. A checkerboard iteration is used to solve the resulting implicit nonlinear systems of finite-difference equations which govern stepwise transition. Qualitative agreement with analytical predictions and experimental results was obtained for some flows with well-known solutions. Previously announced in STAR as N82-16363

Description: Automated information extraction procedures for analysis of multitemporal Landsat data in non-U.S. crop inventory and monitoring are reviewed. Experiments to develop and evaluate crop area estimation technologies for spring small grains, summer crops, corn, and soybeans are discussed. Previously announced in STAR as N82-32793

Description: Agriculture, which occupies a vital position in the economy of the State of California, depends crucially on the available water. The California Department of Water Resources (DWR) is, therefore, greatly concerned with the total water requirements for agricultural applications. In view of the limitations of an area-limited, single-date survey system, the DWR has been cooperating with NASA and the University of California in a study of the applicability of Landsat imagery and digital data as an aid in making decisions concerning the management of water resources. Attention is given to a statewide inventory of irrigated land, computer-assisted estimation and mapping of irrigated land, and a crop type analysis using Landsat digital data.

Description: The development of a preprocessing unit for Landsat Thematic Mapper (TM) data for the Earth Observations Data Laboratory at Johnson Space Center is reported. The background of the project is sketched, including the greatly increased data-handling requirements compared to MSS, the influence of the JPL VICAR system on the system design, and the completeness of the GSFC SCROUNGE (LASLIB) TM data tapes. The design approach and realization are discussed, and the performance and transportability of the preprocessor programs (totaling about 2000 lines of source code in FORTRAN and IBM Assembly languages) are indicated. The system is able to read the TM image tapes, extract areas of interest to particular studies, and register the extracted imagery to suitable references. Ancillary programs include image enhancement, rotation, filtering and pixel-size modification.

Description: Features of the NASA Regional Application Program for providing state and local land management agencies an opportunity to assess the usefulness of emerging remote sensing technology are described. The Program guidelines necessitated configuring software for local facilities, assuring that the aggncy involved furnished manpower, and applying the technology to local needs. The study focused on the southwestern U.S., particularly for purposes of water management, federal/state ownership/policy, energy development, environmental impact issues, timber and range inventory, fire control, and urban expansion. Demonstration projects were conducted in various topics, according to the state surveyed, with the success of the projects determined by the willingness of the agencies to continue with the technology, which happened in several cases.

Description: The California Integrated Remote Sensing System's San Bernardino County Project was devised to study the utilization of a data base at a number of jurisdictional levels. The present paper discusses the implementation of change-detection and masking techniques in the updating of Landsat-derived land-cover maps. A baseline landcover classification was first created from a 1976 image, then the adjusted 1976 image was compared with a 1979 scene by the techniques of (1) multidate image classification, (2) difference image-distribution tails thresholding, (3) difference image classification, and (4) multi-dimensional chi-square analysis of a difference image. The union of the results of methods 1, 3 and 4 was used to create a mask of possible change areas between 1976 and 1979, which served to limit analysis of the update image and reduce comparison errors in unchanged areas. The techniques of spatial smoothing of change-detection products, and of combining results of difference change-detection algorithms are also shown to improve Landsat change-detection accuracies.

Description: The systems of truncated differential equations that have been proposed to reduce the complexity and large computational costs of solutions to the full Navier-Stokes equations are considered. These systems are computationally efficient and capture all the physically relevant behavior. The systems follow a certain hierarchy: (1) the classical boundary-layer equations with specified edge properties (usually the streamwise pressure distribution); (2) the coupled boundary-layer/inviscid equations; (3) the so-called thin-layer equations that discard streamwise diffusion; and (4) the Navier-Stokes equations. Consideration is given to each of these approximations applied to an incompressible, laminar-separating flow at low and moderate Reynolds numbers. It is pointed out that for any flow or region of flow for which viscous-inviscid interaction effects are small, classical boundary-layer equations will provide a satisfactory description of the viscous flow at a fraction of the computational cost of any higher approximations.

Description: A technique is examined for improving the comparability of Landsat multisppectral scanner (MSS) data acquired on different dates. The technique involves conversion of digital brightness counts to relative radiance values measured in energy units (milliwatts per square centimeter-steradian). The statistical data of signature from 23 land cover (or biomass) classifications derived from all three Landsats were compared before and after the radiance normalization. Significant convergence occurred among the data sets for mean spectral values and the variances associated with each of seven major land cover types for MSS bands 4, 5, and 7. Overall, the variance attributed to the sensor component was reduced from 5.39 to 2.69 percent, with the largest decrease occurring in band 4 (14.4 percent to 3.7 percent).

Description: An investigation of the growth of the three-dimensional, counter-rotating, longitudinal type vortices is considered in two-dimensional laminar compressible boundary-layer flow. The basic approximation of the disturbance equations that includes the terms due to boundary layer growth is considered and solved numerically. These terms are shown to have large local effects near the neutral stability region. The study shows that the instability of the boundary layer with respect to the three-dimensional vortices sets in at higher Goertler number as Mach number increases. Also the maximum amplitude ratio of the vortices is reduced by about 20 percent as Mach number increases from 0 to 5.

Description: Monitoring biomass of wetlands ecosystems can provide information on net primary production and on the chemical and physical status of wetland soils relative to anaerobic microbial transformation of key elements. Multispectral remote sensing techniques successfully estimated macrophytic biomass in wetlands systems. Regression models developed from ground spectral data for predicting Spartina alterniflora biomass over an entire growing season include seasonal variations in biomass density and illumination intensity. An independent set of biomass and spectral data were collected and the standing crop biomass and net primary productivity were estimated. The improved spatial, radiometric and spectral resolution of th LANDSAT-4 Thematic Mapper over the LANDSAT MSS can greatly enhance multispectral techniques for estimating wetlands biomass over large areas. These techniques can provide the biomass data necessary for global ecology studies.

Description: Thematic mapper scenes for Washington, D.C. and Macon, Georgia were examined to determine their radiometry and geometric accuracy. Specific band ratios were used to determine their effectiveness in defining vegetation and rock mineralogy. the TM 3/4 band ratio was used to define vegetation and the 5/2 band ratio was used to define limonitic rocks. The 5/7 band ratio was evaluated to test the effectiveness of the 1.6 and 2.2 mm bands in detecting clay and carbonate bearing rocks. Preliminary results show that clay minerals containing absorption bands at 2.2 mm, which are centered in the TM band 7, can be readily detected when the band ratio images are suitably contrast stretched. Bright rocks, such as marbles, which contain absorption bands in the 2.33 mm region, near the wavelength of TM band 7, are only evident upon harsher contrast stretching of the 5/7 band ratio. Geobotanical studies of Washington, D.C. show that monospecific forest canopies can be differentiated.

Description: There are small differences between the average DN for the 16 detectors in each band, typically 0.8 DN; the standard deviations also differ typically by 0.4 DN. Differences of mode in a band are as large as 6 DN. Some DN levels appear to be strongly favored over adjacent levels. Differences between forward and reverse scans are approximately 0.1 DN in the mean, and 0 to 0.6 DN in the standard deviation. Geometrically resampled images (P data), in which the fixed correspondence between lines and single detectors is lost, are statistically similiar to the ensemble of detectors in each band in A data. The magnitude of inter-detector variation is readily seen by making an image of the first derivative in the vertical (line) direction of a flat field and stretching progressively wider ranges to gray; most detectors differ from their neighbors by 1 to 2 DN. The film output from the GSFC filmwriter used for TM images was found to have scale errors in both sample and line directions corresponding to four pixels in a TM image, and skew corresponding to three pixels.

Description: An approach is described for providing periodic inflight absolute radiometric calibrations of the LANDSAT-4 sensors by reference to selected, instrumented ground areas. Results of some early ground measurements and computer simulations are presented. Selection of a suitable ground reference site, accurate measurement of the spectral reflectance of the selected area, determination of atmospheric characteristics during the morning of the sensor overpass, reduction of the measured data and their use in an appropriate atmospheric radiative transfer program, and comparison of the radiance level data with the digital counts of for the images of the selected areas are discussed. Preliminary measurements of gypsum are being made as an aid in defining the characteristics of field equipment to be constructed and calibrated for use over the White Sands Missile Range.

Description: Data collected on the spectral characteristics of the LANDSAT-4 and LANDSAT-4 backup thematic mapper instruments, the protoflight (PF) and flight (F) models, respectively are analyzed and summarized. Tests were conducted on the instruments and their components to determine compliance with two sets of spectral specifications: Band-by-band spectral coverage and channel-by-channel within-band spectral matching.

Description: The TM band 6 shutter background and the 34.7 C internal black body signal were measured over 50 day dates. Variability of the shutter background temperature was from 7 C to 11 C. For ten specific images, the digital counts of the calibration data were measured. The average pulse value of the black body peak decreased from 174 to 149 counts while the shutter background counts varied as a function of shutter temperature from 77 to 85. Relative internal gains between the four channels were calculated and compared to prelaunch values. They showed gains over 9 months of up to 5%. Frequency histograms of number of pixels vs. digital counts from a night scene were used to determine gain relative to the mean and to discern a systematic along-scan pattern in a difference between forward and reverse scan counts of up to 0.5. A corrected digital image was obtained. A temperature estimate for and area of Lake Erie of 18.5 C to 19.9 C was obtained. Local temperature records showed 21 C.

Description: Differences in overall sensor response, due to both factors within the sensor system, and external factors such as atmospheric effects, must be dealt with before change detection techniques using image differencing can be successfully implemented. The approach used to be coregister data to a base, followed by between image scatterogram generation and evaluation, and image differencing. Data from LANDSAT 2 and 3 were registered to LANDSAT 4 data. The area was limited to a small protion of the scene near the City of Santa Cruz because this was the only area cloud and haze free on all the images. Visual examination of each image, as well as the between image scatterograms, provide information on radiometric characteristics of each sensor. The image differencing, after normalizing for radiometric differences, provides a visual depiction of geometric distortions.

Description: Two full frames of radiometrically corrected (Type A) LANDSAT-4 MSS data were analyzed digitally and visually for evidence of residual calibration differences between detectors, quantization effects, and other sensor-related artifacts. Both standard statistical and Fourier analysis techniques were employed. Opportunities for coincident coverage by LANDSATS 3 and 4 were identified in the contiguous 48 states. Paired acquisitions for two scenes were obtained and analyzed to establish relationships between signal values from common areas imaged by the two MSS Systems. Initial findings on detector-to-detector differences, coherent noise, and LANDSAT 4 to LANDSAT 3 calibration are summarized. Results show that LANDSAT 4 MSS produces data of generally good quality with dynamic ranges and target responses similar to those of previous sensors.

Description: Key spectral, radiometric, and geometric characteristics of the TM sensor are examined. Spectrally, band 5 is slightly wider than specified and its upper edge at 50% of miximum of 1784 nm includes some unintended overlap with water absorption bands. Thermal band 6 is half the expected width. Radiometrically, the TM has extreme linearity and stability in comparison with previous MSS photomultiplier systems. Forward and reverse scans on TM show some unexplained radiometric differences of up to four digital levels. Primary focal plane bands show a monotomic decrease in gain of about 5% in the five months since launch. The relative internal gains of bands 5 and 7 varied with a period of about 60 days and an amplitude of about 6%. Radiometric calibration must be applied before histogram equalization algorithms to preserve radiometric accuracy. Geometrically, channel 4 in band 2 has a smaller modulation transfer function than desired. There is apparent misregistration of .75 pixels along scan and 0.2 pixels across scan.

Description: The characterization objectives of the LANDSAT 4 Science Office at GSFC are to: (1) determine the accuracy and precision of sensor and spacecraft performance, image data quality, and derived information; (2) recommend LANDSAT 4 system improvements; and (3) communicate results to the research community. In-house activities are directed toward full access and utilization of the prelaunch and in-orbit engineering test data on the sensor and spacecraft. Principle scientists in remote sensing are involved as part of a major scientific characterization effort, and workshops were held for these investigative teams. A symposium is scheduled prior to turnover of the TM to NOAA.

Description: The LANDSAT 4 thematic mapper sensor possesses approximately twice the spectral resolution, three times the spatial resolution, and four times the spectral sensitivity of the MSS sensor on earlier LANDSAT satellites. Spectral bands on the TM, particularly those at wavelengths of 1.6 and 2.2 micrometers are useful for: (1) distinguishing crops such as rice and soybeans; (2) surveying areas that are cultivated in strip crop fashion; (3) determining clay variations and abundances and rock classifications; and (4) differentiating nutrients and sediments found in coastal waters. The sensor can identify surface features 30 meters on a side, which roughly corresponds to a standard city block. Highway construction, land excavation, urban growth, and the health and extent of vegetation can be detected.

Description: Several environmental parameters presently acknowledged to affect heat transfer are discussed including: (1) the experimental apparatus used, (2) uniform and variable wall temperatures, (3) acceleration effects, (4) deceleration, (5) free stream turbulence, (6) surface roughness, (7) unsteady effects, and (8) secondary flows. Calculation procedures, and some physically based models that are successful in computing heat transfer rates are discussed.

Description: Results are examined from an experiment conducted to determine quantitatively the secondary factors which affect the response of a turbulent boundary layer to convex curvature and to examine the recovery process after curvature ended. The variation of Stanton number with streamwise distance and with enthalpy thickness Reynolds number for the baseline case is shown. The effect of delta sub .99/R on the velocity of the potential core would have if we extended to the wall with no viscous effects, of free stream acceleration, of an unheated starting length, and of boundary layer maturity are discussed. Mixing length and turbulent Prandtl number models are reviewed.

Description: The problem of estimating the parameters which determine a mixture density is reviewed as well as maximum likelihood estimation for it. A particular iterative procedure for numerically approximating maximum likelihood estimates for mixture density problems is considered. This EM algorithm, is a specialization to the mixture density context of a general algorithm of the same name used to approximate maximum likelihood estimates for incomplete data problems. The formulation and theoretical and practical properties of the EM algorithm for mixture densities are discussed focussing in particular on mixtures of densities from exponential families.

Description: An important question in cluster analysis and pattern recognition is the determination of the number of clusters into which a given population should be divided. Frequently, particularly when certain specific clustering methods are being used, the number of clusters is taken to be equal to the number of modes, or local maxima, in the probability density function underlying the given data set. The use of kernal density estimates in mode estimation is discussed. The test statistic to be used is defined and a bootstrap technique for assessing significance is given. An illustrative application is followed by an examination of the asymptotic behavior of the test statistic.

Description: Experience gained in applying nonparametric maximum likelihood techniques of density estimation to judge the comparative quality of various estimators is reported. Two invariate data sets of one hundered samples (one Cauchy, one natural normal) are considered as well as studies in the multivariate case.

Description: The problem of estimating a density f on R sup d from a sample Xz(1),...,X(n) of independent identically distributed random vectors is critically examined, and some recent results in the field are reviewed. The following statements are qualified: (1) For any sequence of density estimates f(n), any arbitrary slow rate of convergence to 0 is possible for E(integral/f(n)-fl); (2) In theoretical comparisons of density estimates, integral/f(n)-f/ should be used and not integral/f(n)-f/sup p, p 1; and (3) For most reasonable nonparametric density estimates, either there is convergence of integral/f(n)-f/ (and then the convergence is in the strongest possible sense for all f), or there is no convergence (even in the weakest possible sense for a single f). There is no intermediate situation.

Description: A method of determining three-dimensional motion and structure from two image frames is presented. The method requires eight point correspondences between the two frames, from which motion and structure parameters are determined by solving a set of eight linear equations and a singular value decomposition of a 3x3 matrix. It is shown that the solution thus obtained is unique.

Description: Methods for the segmentation and recognition of individual targets sensed with forward looking infrared detectors are discussed. Particular attention is given to an adaptive multi-scenario target screener.

Description: The structural analysis of remotely sensed imagery is defined and basic techniques for implementing the process are described. Structural analysis uses knowledge of the properties of an entity, its parts and their relationships, and the relationships in which it participates at a higher level to locate and recognize objects in a visual scene. The representation of structural knowledge, the development of algorithms for using the knowledge to help analyze an image, and techniques for storage and retrieval of relational models are addressed.

Description: Computer-based techniques for automatic photointerpretation based upon information derived from texture and morphology analysis of images are discussed. By automatic photointerpretation, is meant the determination of semantic descriptions of the content of the images by computer. To perform semantic analysis of morphology, a heirarchical structure of knowledge representation was developed. The simplest elements in a morphology are strokes, which are used to form alphabets. The alphabets are the elements for generating words, which are used to describe the function or property of an object or a region. The words are the elements for constructing sentences, which are used for semantic description of the content of the image. Photointerpretation based upon morphology is then augmented by textural information. Textural analysis is performed using a pixel-vector approach.

Description: Methods used to measure the geometrical properties of regions in a segmented image are discussed including the use of centroids, moments, and principle axes. In addition, statistical picture properties, particularly those which describe visual texture, are discussed. Gray level statistics, local property statistics, and autocorrelation and power spectrum are addressed.

Description: Research into the role of cooperative, or relaxation, processes in image segmentation is surveyed. Cooperative processes can be employed at several levels of the segmentation process as a preprocessing enhancement step, during supervised or unsupervised pixel classification and, finally, for the interpretation of image segments based on segment properties and relations.

Description: The methodologies and capabilities of image segmentation techniques are reviewed. Single linkage schemes, hybrid linkage schemes, centroid linkage schemes, histogram mode seeking, spatial clustering, and split and merge schemes are addressed.

Description: Given N distinct points (X sub i, Y sub i) and N real numbers Z sub i, BSPLASH constructs a function G (x, y) that satisfies G (x sub i, y sub i) = Z sub i for i = 1,..., N. This C(2) interpolant consists of a bicubic spline approximation and Shepard's bivariate interpolant.

Description: The physical and geometric interpretation of a surface fitting technique, multiquadric equations (MQ), is discussed. The relation of this method and its reciprocal form to biharmonic and harmonic techniques respectively, is pointed out. In both forms the solutions may be viewed as being numerical approximations of an integral equation in which an unknown density function is the physical source for disturbing potential (reciprocal-MQ) or elastic displacement (MQ).

Description: An algorithm is described for constructing a smooth computable function, f, defined over the surface of a sphere and interpolating a set of n data values, u sub i, associated with n locations, P sub i, on the surface of the sphere. The interpolation function, f, will be continuous and have continuous first partial derivatives. The locations, p sub i, are not required to lie on any type of regular grid.

Description: A variety of numerical methods for fitting a function to data given at a set of points scattered throughout a domain in the plane are surveyed. Four classes of methods are discussed: (1) global interpolation; (2) local interpolation; (3) global approximation; and (4) local approximation. Also, two-stage methods and contouring are discussed. The surfaces constructed include polynomials, spline functions, and rational functions, among others.

Description: Some mathematical/statistical problems within the AgRISTARS program amendable to investigations involving the use of surface fitting techniques are overviewed. The Bayes and maximum likelihood rules, bias determination, regression estimators, parameter estimation, and classifier design are addressed.

Description: The Lagrangian dispersion theory of Durbin (1980) is used to analyze experiments by Warhaft and Lumley (1978) and by Sreenivasan et al. (1980) on temperature fluctuations in grid-generated turbulence. Both theory and experiment show that the decay exponent m depends on the ratio of the initial length scales of velocity and temperature, although when this ratio is greater than 2.5 such dependence is negligible. The theory shows that m is not truly constant, but within the range covered by the experiments it is nearly so. The agreement between theory and experiment lends credence to the idea that the decay of fluctuations is controlled largely by turbulent relative dispersion.

Description: Image processing and enhancement techniques for improving the geologic utility of digital satellite radar images are reviewed. Preprocessing techniques such as mean and variance correction on a range or azimuth line by line basis to provide uniformly illuminated swaths, median value filtering for four-look imagery to eliminate speckle, and geometric rectification using a priori elevation data. Examples are presented of application of preprocessing methods to Seasat and Landsat data, and Seasat SAR imagery was coregistered with Landsat imagery to form composite scenes. A polynomial was developed to distort the radar picture to fit the Landsat image of a 90 x 90 km sq grid, using Landsat color ratios with Seasat intensities. Subsequent linear discrimination analysis was employed to discriminate rock types from known areas. Seasat additions to the Landsat data improved rock identification by 7%.

Description: An examination of the possibilities of using Landsat data to simulate NOAA-6 Advanced Very High Resolution Radiometer (AVHRR) data on two channels, as well as using actual NOAA-6 imagery, for large-scale hydrological studies is presented. A running average was obtained of 18 consecutive pixels of 1 km resolution taken by the Landsat scanners were scaled up to 8-bit data and investigated for different gray levels. AVHRR data comprising five channels of 10-bit, band-interleaved information covering 10 deg latitude were analyzed and a suitable pixel grid was chosen for comparison with the Landsat data in a supervised classification format, an unsupervised mode, and with ground truth. Landcover delineation was explored by removing snow, water, and cloud features from the cluster analysis, and resulted in less than 10% difference. Low resolution large-scale data was determined useful for characterizing some landcover features if weekly and/or monthly updates are maintained.

Description: (Previously announced in STAR as N81-19529)

Description: Problems associated with the use of Landsat multispectral scanner (MSS) imagery for the detection of urban growth and land use patterns are discussed. The presence of vegetation, either original or added between scanning periods, has been found to dramatically effect the range of signatures in a given area. Different land use developmental stages have been successfully identified by means of 1:50,000 scale panchromatic aerial photography, a resolution only considered possible by spaceborne instrumentation with the advent of the Landsat D satellite. Textural information generated through the grey-tone spatial-dependency matrix for the Landsat band 5 data is compared for different years and a change detection algorithm is described. It is found that the addition of vegetation during development after the removal of natural vegetation resulted in error of omission in the single band data, which must therefore only be used in concert with other data sources.

Description: Procedures necessary for the development of a generalized three-dimensional perspective software capability in support of graphic, topographic, and color mapping of Landsat data are reviewed. The NASA Earth Resources Laboratory developed the procedures in order to facilitate the processing and analysis of disparate, geographically oriented base maps from aircraft and satellite sensors. Perspective displays are obtained through a translation of the space-viewed object to a vantage point coordinate system, followed by a rotation through two angles for alignment along the vantage line of sight, and finally a perspective transformation to yield two-dimensional displays with no hidden lines. Matrix equations for the transformations are reviewed, including scaling, and block diagrams are provided of the data and perspective software systems. The classification data plane may be mapped onto a topographic elevation data plane.

Description: The effect of large deformation in the flow between the bellmouth and centerbody is considered analytically for application to studies of vortex breakdown in a pipe. Basic equations are defined for axisymmetric inviscid swirling flows at the inflow and outflow sections. Axial and circumferential velocity component profiles are presented, and comparisons are made with trials involving vane angles of 42 deg and Re of 2300. Axial components of the prediction matched well in the inner half of the pipe radius and not well with the outer, while circumferential predictions were good only at the axis. A lack of viscosity was concluded to result in the inaccuracies near the wall.

Description: A modified Kubelka-Munk model has been utilized to derive useful equations for the analysis of apparent canopy reflectance. Based on the solution to the model simple working equations were formulated by employing reflectance characteristic parameters. The relationships derived show the asymptotic nature of reflectance data that is typically observed in remote sensing studies of plant biomass. They also establish the range of expected apparent canopy reflectance values for specific plant canopy types. The usefulness of the simplified equations was demonstrated by the exceptionally close fit of the theoretical curves to two separately acquired data sets for alfalfa and shortgrass prairie canopies.

Description: The following working objectives were adopted: (1) define the current state of knowledge concerning the role of multispectral imaging science in hydrology; (2) identify critical areas where gaps in our knowledge limit opportunities for significant improvements in our understanding of the hydrologic processes; (3) evaluate the potential of multispectral imaging sciences as tools to close these gaps in knowledge; and (4) develop guidelines for a series of remote-sensing-based experiments that would help close these gaps in knowledge and, thereby, provide man with the improved scientific base necessary for better utilization of the world's water resource. The resulting documentation is intended to provide guidance for multispectral imaging programs in the hydrologic sciences with special emphasis on the visible and infrared (IR) wavelengths.

Description: Specific activity in information extraction science (taken to include data handling) is needed to: help identify the bounds of practical missions; identify potential data handling and analysis scenarios; identify the required enabling technology; and identify the requirements for a design data base to be used by the disciplines in determining potential parameters for future missions. It was defined that specific analysis topics were a function of the discipline involved, and therefore no attempt was made to define any specific analysis developments required. Rather, it was recognized that a number of generic data handling requirements exist whose solutions cannot be typically supported by the disciplines. The areas of concern were therefore defined as: data handling aspects of system design considerations; enabling technology for data handling, with specific attention to rectification and registration; and enabling technology for analysis. Within each of these areas, the following topics were addressed: state of the art (current status and contributing factors); critical issues; and recommendations for research and/or development.

Description: The use of multispectral imaging systems in land use, geomorphological, and cartographic applications is examined. Spatial, spectral, and geometric resolution requirements for photo interpretation and multispectral pattern recognition are discussed. The potential contributions of these systems in specific experiments is also included.

Description: The role that TM and MSS data play in the analysis of spatial patterns for land use/land cover, geomorphology studies, and the development of cartographic products is discussed. Tables listing geographic science data gaps, mission data requirements, and possible future remote sensing missions are included.

Description: The results of a study to evaluate Landsat digital data, categorized by land cover, for input to the Maryland Automated Geographic Information (MAGI) system, the state georeferenced data base, are presented. Good correspondence is found between the MAGI system and Landsat data for six of seven categories: forest, water, crop/pasture, medium-density residential, low-density residential, and transitional (disturbed land, construction). Discrepancies between the results are found for commercial/industrial/institutional areas which are due to differences in interpretative methodologies, not to deficiencies in either data source. It is concluded that Landsat data are suitable for future Maryland land cover inventories, and can also be used to augment MAGI system data.

Description: Two iterative schemes based on the mixed finite element method are developed for analyzing steady natural convection in a melt adjacent to its solid phase. The simplest method decouples the calculation of the field variables and the shape of the melt/solid interface into two interlocked iterations that are performed successively. The second method uses Newton's iteration to solve simultaneously for both types of unknowns and has a quadratic convergence rate. Results for a model problem of melt and solid in a cylindrical ampoule show the Newton algorithm to be a factor of three more efficient.

Description: Incompressible turbulent channel flow is investigated by large eddy simulation using improved numerical methods and boundary conditions. In downstream and spanwise directions, cyclic boundary conditions are imposed for velocity and pressure, and two types of boundary conditions near the wall are used and compared. One type is based on the logarithmic law of the mean velocity near the wall and has a slip boundary condition where the molecular-viscous term is neglected. The other type is based on a no-slip boundary condition, where fine mesh spacing near the wall is used to take account of the molecular viscosity. Although the present study employs a coarse mesh (16 x 16 x 21), its results are in good agreement with those of Moin and Kim (1981).

Description: One of the objectives of the Saginaw River Basin study is related to the development of a computer model to predict flood damages. The computer model is to be operational in June 1985. In order to achieve this objective, the input of land-use data into a data base consisting of 198,000 grid cells will be required. A planning technique using Spatial Analysis Methodology (SAM) was developed by the Corps of Engineers Hydrologic Engineering Center (HEC) to systematically handle these data. The HEC-SAM system uses the spatially oriented map data in a series of data management and analysis software programs for input to the Corps hydrologic and environmental models. Attention is given to data base development, Landsat digital data, the placement of the Landsat data into the grid cell data base, and the development of the land cover classification. The Landsat-2 MSS scene covering 85 percent of the Saginaw River Basin was geometrically corrected to a UTM coordinate system.

Description: Extensive studies conducted by several researchers using truck-mounted active microwave sensors have shown the sensitivity of these sensors to soil moisture variations. The logical extension of these results is the evaluation of similar systems at lower resolutions typical of operational systems. Data collected during a series of aircraft flights in 1978 and 1980 over four rangeland watersheds located near Chickasha, Oklahoma, were analyzed in this study. These data included scatterometer measurements made at 1.6 and 4.75 GHz using a NASA aircraft and ground observations of soil moisture for a wide range of moisture conditions. Data were analyzed for consistency and compared to previous truck and aircraft results. Results indicate that the sensor system is capable of providing consistent estimates of soil moisture under the conditions tested.

Description: A vegetation gradient model, based on a new surface hydrologic index and NOAA/AVHRR meteorological satellite data, has been analyzed along a 1300 km east-west transect across the state of Texas. The model was developed to test the potential usefulness of such low-resolution data for vegetation stratification and monitoring. Normalized Difference values (ratio of AVHRR bands 1 and 2, considered to be an index of greenness) were determined and evaluated against climatological and vegetation characteristics at 50 sample locations (regular intervals of 0.25 deg longitude) along the transect on five days in 1980. Statistical treatment of the data indicate that a multivariate model incorporating satellite-measured spectral greenness values and a surface hydrologic factor offer promise as a new technique for regional-scale vegetation stratification and monitoring.

Description: The capabilities of the Advanced Very High Resolution Radiometer (AVHRR) for land cover mapping were investigated by comparing the accuracy of land cover information for the Washington, DC area derived from NOAA-7 AVHRR data with that from Landsat Multispectral Scanner (MSS) data. Unsupervised Level I land cover classifications were performed for MSS and AVHRR data sets collected on July 11, 1981. A detailed accuracy assessment was conducted based on ground truth delineated on six USGS 7.5 minute series topographic maps. Preliminary results produced overall land cover classification accuracies of 75.6 percent and 76.1 percent for AVHRR and MSS, respectively. While the accuracies for predominant categories such as agriculture, forest, and urban were similar for both sensors, discrimination of the less commonly occurring categories such as barren, wetland, and water was improved with the MSS data set. The AVHRR, however, performed as well as or better than the MSS in classifying large homogeneous areas. The application of AVHRR data with its lower processing cost and more frequent worldwide coverage appears promising for global land cover mapping.

Description: The design and operation of a laser detection system for migrating birds are presented. A battery-powered class-III laser (operating at 904 nm, pulse-repetition rate 5 kHz, pulse duration 100 nsec, and peak power 25 W) and a photodiode receiver are mounted on poles at height 10 m and distance 850 m and equipped with 135-mm f/2.8 collimating lenses; beam diameter at the receiver is 1.7 m. The microprocessor-controlled system is found to detect the passing of an object as small as 30 sq cm in cross section at a distance of 425 m.

Description: The velocity characteristics of laminar and turbulent developing flow in an S-duct formed from two 22.5-deg bends of rectangular cross-section have been studied experimentally using laser Doppler velocimetry. It is shown that pressure-driven secondary flows arise in the first bend of the duct and reach maxima of 0.22 and 0.15 of the bulk velocity in the laminar and turbulent flows, respectively. The velocities are greater in the laminar flow, mainly because of the thicker inlet boundary layers. On passing through the second half of the S-duct, a secondary flow is established over most of the section in the direction opposite to that in the first half. Near the outer wall of the second bend, however, the secondary flow generated in the first bend is sustained because of the local sign of radial vorticity. This effect contributes to a redistribution of the streamwise isotachs, by the end of the duct, comparable with that in unidirectional bends.

Description: The objective of the study was to evaluate the utility of thematic mapper data as a source of geologically useful information for mountainous areas of varying vegetation density. Much of the processing was done in an a priori manner without prior ground-based information. This approach resulted in a successfull mapping of the alteration associated with the Mt. Emmons molybdenum ore body as well as several other hydrothermal systems. Supervised classification produced a vegetation map at least as accurate as the mapping done for the environmental impact statement. Principal components were used to map zones of general, subtle alteration and to separate hematitically stained rock from staining associated with hydrothermal activity. Decorrelation color composites were found to be useful field mapping aids, easily delineating many lithologies and vegetation classes of interest. The factors restricting the interpretability and computer manipulation of the data are examined.