ALBERT

Description: This paper presents the results of a series of total and spectral solar irradiance measurements made at ground surface (Table Mountain Facility, Calif., altitude 2.18 km). The spectral irradiance data are presented for the 0.3-3.0-micron spectral region for air mass 1.5.

Description: A proposal for a multi-institutional investigation of the processes involved in the growth and maintenance of high level extended clouds is presented. Mapping of variability of the cloud and of its radiative characteristics in terms of the meteorological environment of the cloud; performance of case studies involving observation of the cloud microphysics and radiation characteristics; and investigation of the processes responsible for the generation, maintenance, and dissipation of the cloud system are recommended. Both modeling and monitoring activities are considered. The specific research projects which the author proposes to carry out are described. Suggestions for the administrative organization of the total effort are presented.

Description: The interplay of the various physical processes involved in the formation, maintenance, and decay of middle and upper tropospheric stratiform clouds is discussed. Ice phase fair weather cloud forms are considered. Simulations of cirriform clouds which attempt to incorporate the physical processes in an interactive manner were performed. A two dimensional time dependent Eulerian numerical model, which incorporates all of the important physical processes in a simplified way, is employed to investigate the role of these processes in the evolution of a cloud in an isolated atmospheric layer. Physical parameters considered are the eddy viscosity and the thermal, water vapor, and ice water eddy diffusivities.

Description: A model that explains the flat-spot power loss phenomenon is presented. Evidence suggests that the effect is due to localized metallurgical interactions between the silicon substrate and the contact metallization. These reactions are shown to result in localized regions in which the P-N junction is destroyed and replaced with a metal semiconductor-like interface. The effects of thermal treatment, crystallographic orientation, junction depth, and metallization are shown along with a method of preventing the effect through the suppression of vacancy formation at the free surface of the contact metallization. Data indicating the effectiveness of a TiN diffusion barrier in preventing the effect are also given.

Description: Stratospheric limb radiance profiles versus altitude of closest approach of the line of sight to the Earth's surface have been measured before and after the Mount St. Helens eruptions by means of photographs taken from a Sun-oriented balloon gondola floating above 35 km altitude over France. Preliminary data were reported for flights in October 1979 and in May and June 1980. The radiance integrated along the line of sight as in-situ radiance (R) can be derived taking into account absorption by ozone and air. The onion peeling inversion method was used to derive the vertical radiance (R) profiles respectively. The values of R were determined in the solar azimuth. The solar elevation angles are chosen larger for the backscattering observation than for the forward scattering observation to deal with as similar illumination conditions as possible despite the Earth's sphericity.

Description: Microscopical investigation of volcanic ash collected from ground stations during Mount St. Helens eruptions reveal a distinctive bimodel size distribution with high concentrations of particle ranges at (1) 200-100 microns and (2) 20-0.1 microns. Close examination of individual particles shows that most larger ones are solidified magma particles of porous pumice with numerous gas bubbles in the interior and the smaller ones are all glassy fragments without any detectable gas bubbles. Elemental analysis demonstrates that the fine fragments all have a composition similar to that of the larger pumice particles. Laboratory experiments suggest that the formation of the fine fragments is by bursting of glassy bubbles from a partially solidified surface of a crystallizing molten magma particle. The production of gas bubbles is due to the release of absorbed gases in molten magma particles when solubility decreases during phase transition. Diffusion cloud chamber experiments strongly indicate that sub-micron volcanic fragments are highly hygroscopic and extremely active as cloud condensation nuclei. Ice crystals also are evidently formed on those fragments in a supercooled (-20 C) cloud chamber. It has been reported that charge generation from ocean volcanic eruptions is due to contact of molten lava with sea water. This seems to be insufficient to explain the observed rapid and intense lightning activities over Mount St. Helens eruptions. Therefore, a hypothesis is presented here that highly electrically charged fine solid fragments are ejected by bursting of gas bubbles from the surface of a crystallizing molten magma particles.

Description: The direct solar radiation transmission record at Mauna Loa, dating from 1958 to the present, revealed with remarkable precision the presence of stratospheric aerosol from volcanic activity. This record can be used to quantify the intensity of the stratospheric volcanic aerosol perturbation following a significant eruption in reference to the Agung event in 1963. The Mount St. Helens' stratospheric cloud was first detected by lidar at 18 km over Mauna Loa on 17 July. The atmospheric transmission was seen to decrease slightly after that time, but only a few tenths of 1 percent. Although it is still fairly early to draw a definite conclusion on the ultimate magnitude of the Mount St. Helens stratospheric aerosol from the Mauna Loa results, it can be stated that the stratospheric aerosol optical depth presently observed is comparable with that observed from Fuego which erupted in 1974. At Boulder, Colorado, the atmospheric debris from Mount St. Helens was observed by lidar on a number of occasions. Also, observations of the diffuse, total and direct transmission of solar radiation were made on June 3 and 4. The latter set of observations is useful for deriving information on the scattering properties of the volcanic cloud. The lidar and solar radiation data are presented and some of their special features are discussed.

Description: Samples of stratospheric aerosols collected with U-2 aircraft for several months following the first three major eruptions of Mount St. Helens were analyzed for ash and liquid acid content. Ash grain sizes and compositions vary depending on collection altitude, location within the drifting cloud, and days following their injection. s computers Size distributions of ash particles vary with altitude. Generally small particles are depleted more rapidly at low altitudes (12 km) than at higher altitudes (17-18 km). Although samples collected 1 day after the first eruption of May 18, 1980, were dry, flow marks on the aircraft indicated parts of the cloud contained heavy acid concentrations. Indeed, all other samples obtained within 1 to 4 days after later eruptions (May 25 and June 12, 1980) were covered with copious amounts of liquid acid. Proportions of liquid to ash varied considerably depending on sampling location and cloud age. Because the acid-coated ash globules were large, they rapidly fell from the stratosphere until, by late June 1980, only a residue of acid droplets remained. Size distributions and concentrations of these droplets varied considerably.

Description: The NASA large flexible solar array space shuttle flight experiment is described. The 32 x 4 m wing is deployed from the shuttle bay, and experiments in electrical output, multiple deployment, and structural dynamics are planned. Both 2 x 4 cm and 5.9 x 5.9 cm cell assemblies on the array blanket are evaluated. Safety/hazards provisions are described, including emergency jettison provisions. Ground testing and hardware fabrication are summarized.

Description: A development program to produce 5.9 x 5.9 cm space quality silicon solar cells with a cost goal of 30 $/W is described. Cell types investigated include wraparound dielectric, mechanical wraparound and conventional contact configurations with combinations of 2 or 10 ohm/cm resistivity, back surface reflectors and/or fields, and diffused or ion implanted junctions. A single step process to cut cell and cover glass simultaneously is being developed. Results for cell and array tests are given. Large solar arrays that might use cells of this type are discussed.

Description: Objectives and progress in both low concentration ratio (6 to 10) and high concentration ratio ( 100) array developments are summarized. Problems encountered include: thermal control, maldistribution of concentrated sunlight, current busing, and optical surface degradation. The potential advantages over planar arrays are an order of magnitude reduction in per unit cost of power plus increased immunity to radiation damage.

Description: Current-voltage curves were calculated for each cell in a cascade structure using a solar cell diode equation and superposition. Terms for the light generated current, diffusion current, space charge recombination current and series and shunt resistance are included. Individual current voltage curves are added in series with ohmic resistance losses for the cell interconnects to obtain the cascade cell performance. Temperature was varied with concentration, using several models, and ranged from 55 C at one Sun to between 80 and 200 C at 100 Suns. A variety of series resistance and internal resistances were used. Coefficients of the diffusion and recombination terms are strongly temperature dependent. The study indicates that maximum efficiency (30%) occurs in the 50 to 100X Sun concentration range, provided series resistance is below 0.015 ohm-sq cm and cell temperature is 80 C at 100 Suns.

Description: Gallium and boron doped silicon solar cells, processed by ion implantation followed by either laser or furnace anneal were irradiated by 1 MeV electrons and their postirradiation recovery by thermal annealing was determined. During the postirradiation anneal, gallium doped cells prepared by both processes recovered more rapidly and exhibited none of the severe reverse annealing observed for similarly processed 2 ohm-cm boron doped cells. Ion implanted furnace annealed 0.1 ohm-cm boron doped cells exhibited the lowest post-irradiation annealing temperatures after irradiation. The drastically lowered recovery temperature is attributed to the reduced oxygen and carbon content of the 0.1 ohm-cm cells. Analysis based on defect properties and annealing kinetics indicates that further reduction in annealing temperature is attainable with further reduction in the silicon's carbon and/or divacancy content after irradiation.

Description: Nineteen stratospheric samples from the eruption plumes of Mount St. Helens were collected in five flight experiments. The plume samples were collected at various altitudes from 13.1 to 20.7 km by using the Ames cryogenic sampling system on board the NASA U-2 aircraft. The enriched, cryogenically collected samples were analyzed by chromatography. The concentrations of aerosols precursor gases (OCS, SO2, and CS2), CH3Cl, N2O, CF2Cl2, and CFCl3 were measured by gas chromatography. Large enhancement of the mixing ratio of SO2 and moderate enhancement of CS2 and OCS were found in the plume samples compared with similar measurement under pre-volcanic conditions. A fast decay rate of the SO2 mixing ratio in the plume was observed. Measurement of Cl(-), SO2(2-), and NO3(-) by ion chromatography was also carried out on water solutions prepared from the plume samples. The results obtained with this technique imply large mixing ratios of HCl, (NO + NO2 + HNO3), and SO2, in which these constituents are the respective sources of the anions. Measurement of the Rn222 concentration in the plume was made. Other stratospheric constituents in the plume samples, such as H2O, CO2, CH4, and CO, were also observed.

Description: Mount St. Helens erupted somewhat less than 0.5 cu km of magma (dense rock equivalent) on May 18, 1980. The May 18 event was usually violent. As much 35% of the volume of the airfall material fell outside of the 2.5 mm isopach, which encloses about 88,000 sq km. This extraordinary dispersive power was transmitted by an eruption column which reached heights of more than 20 km. There was a lateral blast (or surge) of unusually large dimensions associated with the onset of the eruption. The magma is dacitic in composition and had a low ( 500 ppm) sulfur content. Distal ashes contain much nonmagmatic (lithic) material, but smaller ( 50 microns m) particles are mostly finely divided magmatic dacite. The grain size distributions of the ash are multimodal, frequently with peaks at 90, 25, and 10 microns. The finer populations fell out faster than their terminal velocities as simple particles would suggest. It is inferred that large proportions of the fine ash fell out as composite particles. This condition greatly reduces the atmospheric burden of silicate particles. Some of the unusual aspects (violence, intense surges, multimodal grain size distributions, lithic content of the ashes) of the eruption may be due to its phreatomagmatic character. The hydrothermal system above the magma may have infiltrated the magma body at the onset of the eruption. An "overprint" of the geochemistry of this hydrothermal system on the geochemistry of the magmatic gas system is likely. One important feature is that reduced gas species may be much more abundant than in many eruptions. Another is that fine ash may form aggregates more readily.

Description: The goals of map/wind (winter in Northern Europe) are to better understand: (1) the interaction of planetary waves of tropospheric origin; (2) the temporal and spatial development of sudden stratospheric warmings; (3) the temporal and spatial development of mesospheric cooling events in conjunction with stratospheric warmings; (4) the vertical and horizontal transport of minor constituents; (5) the effects on the chemistry of neutral and charged species of the large temperature changes occurring during stratospheric warmings and mesospheric cooling; (6) sources of turbulent energy; (7) the temporal and spatial development of turbulent layers; and (8) the contributions of dynamical processes to the heating and cooling of the mesospheric and turbopause region.

Description: Three general areas of study were identified: stratospheric composition; mesospheric and lower ionospheric structure and composition; and middle atmospheric dynamics. The role of chemical reactions and spectroscope in the study of the middle atmosphere is discussed.

Description: Organizations in the United States which are interested in MAP participation were surveyed. Satellites, rockets, balloons, and ground support systems are listed with available experimentation.

Description: The plans for India's participation in the middle Atmosphere Program are outlined.

Description: The NASA Lewis Research Center in cooperation with the World Health Organization, U.S.A. I.D., the Pan American Health Organization and national government agencies in some developing countries sponsored the installation of twenty photovoltaic powered medical vaccine storage refrigerator-freezer (R/F) systems. The Solar Power Corporation was selected as the contractor to perform the design, development and installation of these twenty units. Solar Power's experiences are described herein.

Description: The U.S. Coast Guard has developed a qualification test to screen photovoltaic modules for utilization on marine aids to navigation. The test is based on a combined-environment of hot and cold saltwater immersion and air pressurization. The test has demonstrated a very high acceleration factor and excellent correlation of electrical failures with modules in a concurrent real-time marine exposure.

Description: Design principles suggested here aim toward high conversion efficiency (greater than 15 percent) in polysilicon cells. The principles seek to decrease the liabilities of both intragranular and grain-boundary-surface defects. The advantages of a phosphorus atom concentration gradient in a thin (less than 50 microns) base of a p(+)/n(x)/n(+) drift-field solar cell, which produces favorable gradients in chemical potential, minority-carrier mobility and diffusivity, and recombination lifetime (via phosphorus gettering) are suggested. The degrading effects of grain boundaries are reduced by these three gradients and by substituting atoms (P, H, F or Li) for vacancies on the grain-boundary surface. From recent experiments comes support for the benefits of P diffusion down grain boundaries and, for quasi-grain-boundary-free and related structures. New analytic solutions for the n(x)-base include the effect of a power-law dependence between P concentration and lifetime. These provide an upper-bound estimate on the open circuit voltage. Finite-difference numerical solutions of the six Shockley equations furnish complete information about all solar-cell parameters and add insight concerning design.

Description: Major advances in photovoltaic (PV) Power Conditioning (PC) with respect to performance and low-cost potential have been made. Solutions have been obtained to interface and control problems related to adapting available inverter designs to the grid-connected, residential photovoltaic experiments. A description is presented to contributing research and development activities. Attention is given to aspects of residential systems experience, conceptual design studies, questions of optimum topology development, and promising advanced designs for residential PV provided by development efforts of the private sector.

Description: Mechanical fatigue of solar cell interconnects is a major failure mechanism in photovoltaic arrays. A comprehensive approach to the reliability design of interconnects, together with extensive design data for the fatigue properties of copper interconnects, has been published. This paper extends the previous work, developing failure prediction (fatigue) data for additional interconnect material choices, including aluminum and a variety of copper-Invar and copper-steel claddings. An improved global fatigue function is used to model the probability-of-failure statistics of each material as a function of level and number of cycles of applied strain. Life-cycle economic analyses are used to evaluate the relative merits of each material choce. The copper-Invar clad composites demonstrate superior performance over pure copper. Aluminum results are disappointing.

Description: Computer analysis indicates that a substantial increase in solar cell conversion efficiencies can be achieved by using two-cell, multi-bandgap tandem structures instead of single-junction cells. Practical AM1 efficiencies of about 30 percent at one sun and over 30 percent at multiple suns are to be expected. The further increases in efficiency calculated for a three-cell tandem structure are much smaller and may not justify the added complexity. For inexpensive two-cell tandem modules, Si is preferred for the bottom cell, and the top-cell material should have a bandgap of 1.75 to 1.80 eV. The GaAs-AlAs and GaAs-GaP systems are very attractive candidates for the top cell. Significant advances have been achieved in growing GaAs on Ge-coated Si substrates (for the two-terminal, two-cell structure) and in growing free-standing ultrathin GaAs layers (for the two-terminal or four-terminal structures). These advances should be transferable to the GaAs-AlAs and GaAs-GaP systems.

Description: The electric output of flat-plate photovoltaic arrays changes constantly, due primarily to changes in cell temperature and irradiance level. As a result, array loads such as direct-current to alternating-current power conditioners must be able to accommodate widely varying input levels, while maintaining operation at or near the array maximum power point.The results of an extensive computer simulation study that was used to define the parameters necessary for the systematic design of array/power-conditioner interfaces are presented as normalized ratios of power-conditioner parameters to array parameters, to make the results universally applicable to a wide variety of system sizes, sites, and operating modes. The advantages of maximum power tracking and a technique for computing average annual power-conditioner efficiency are discussed.

Description: Observations of waves stimulated by artificial injection inside an auroral arc by an electron accelerator mounted on the POLAR 5 sounding rocket are presented. The accelerator produced a pulsed electron beam with currents up to 130 mA and energies up to 10 keV; emissions after the end of beam injection were generated by perturbations in the ambient plasma near the accelerator during beam injection. These emissions were independent of the electron beam direction along the geomagnetic field. The high frequency emission observed after beam injection correlated with the passage through an auroral arc; the low frequency emissions after beam injection were concentrated in two bands below the lower hybrid frequency.

Description: Measurements of average proton, helium, carbon, and oxygen fluxes at 6.6 earth radii are reported. The data represent averages obtained on ATS 6 between June 15 and Oct. 3, 1974. The energy range covered was 0.36-1.1 MeV for protons and approximately 1-4 MeV for the heavier ions. The results indicate that above about 1 MeV the heavier ion fluxes dominate over the proton flux on the energy/ion scale. Using two different spectral dependencies to fit the data, the carbon to oxygen concentration ratio for energies above 1 MeV was found to be 0.43 for the power law spectrum and 0.44 for the exponential spectrum. Thus in either case the abundance ratio is consistent with the solar origin of the particles. Similarly, the helium to oxygen concentration ratio is found to be 0.17 for the power law spectrum and 0.28 for the exponential spectrum. This is inconsistent with the solar wind ratio, which is about 10. The results quoted above are based on a very small portion of the distribution function above 1 MeV.

Description: Rocket ozone soundings have been conducted in the stratosphere and lower mesosphere at high latitudes during winter. The collection of soundings show a high degree of variability when compared to ozone distributions measured during summer and at lower latitudes. The concurrently observed temperature and winds also show large variations which can be qualitatively related to the ozone profiles. Two most unusual ozone profiles were observed in January 1979 over Alaska during a stratospheric warming event. Both ozone profiles were consistent in showing the measured mixing ratios to be higher at 50 km than those measured at 40 km, a feature never reported before. This feature is related to the concurrently observed wind and temperature distributions and the NMC analyses of pressure height fields. The polar night ozone observations in the upper stratosphere and lower mesosphere suggest some temperature dependence, but transports seem to play an important role.

Description: Two years of Nimbus 4 backscattered ultraviolet data have been recalibrated and reprocessed. A Laplace transform inversion was applied to radiances at 2876 A and below for 560,000 individual scans for the period April 1970-May 1972. The behavior of ozone near 50 km as a function of time, latitude, and longitude is presented. The high-latitude 1-mbar ozone mixing ratio is maximum at the winter solstice, about 10 microgram/g and is minimum at the summer solstice, about 4 microgram/g. Below 30 deg latitude the ozone is fairly constant at 4 microgram/g. Ozone variability is large in winter and spring and small in summer and fall.

Description: Three measurements of ionospheric electric field were made during the 24-h ALADDIN rocket program at Wallops Island on June 29-30, 1974. The first of these used a double probe instrument, flown at 1500 Local Solar Time, and the second and third measurements were made by barium cloud releases at evening and morning twilight. These three electric field vectors have been compared with the predictions of a number of models of electric field due to the dynamo effects of various atmospheric tides, and also of a possible magnetospheric origin. On the assumption that the measurements were made at a location equatorward of the afternoon convergence and poleward of the morning divergence in the electric field patterns related to the Sq current system, Stening's (1973) model of the diurnal variation of the electric field induced by the (1, -2) tidal model at the time of the summer solstice correctly predicts the directions of the observed electric field. Forbes and Lindzen's (1976, 1977) model, incorporating the three major propagating tidal modes as well as the evanescent (1, -2) mode, also bears an acceptable relationship to the ALADDIN electric field directions. The ALADDIN E-field magnitudes are comparable with those obtained by ground-based observations from Millstone Hill and from Saint Santin but are about half of Stening's model values, and three times those of Forbes and Lindzen. Saint Santin E-field directions, at the same latitude but 75 deg difference in longitude, are distinctly different from ALADDIN, implying that longitudinal differences are significant.

Description: The first effects of a nearby (10 parsec) supernova on the earth's atmosphere will be caused by ultraviolet radiation dissociating molecular oxygen. The event will be of about one month's duration. Several months later nuclear gamma radiation may arrive, causing a decrease in atmospheric ozone. Cosmic radiation from the supernova remnant will not intercept the earth for at least 1000 years at which time ozone will be seriously depleted. Supernova ultraviolet radiation increases column ozone and atomic oxygen. Atmospheric thermal structure is modified with a large temperature increase in the mesosphere and lower thermosphere and a decrease at higher altitudes caused by enhanced heat loss due to atomic oxygen radiation and conduction.

Description: A study of a large number of temperature measurements in the middle atmosphere shows a much more complex thermal structure of this region than described in the U.S. Standard Atmosphere, 1976. The mesopause height which is generally assumed to be at 80 km varies between 70 and 100 km, often with two minima in temperature at about 70 and 100 km and a maximum between 80-85 km. By solving the energy balance equation and the equations of continuity, the physical significance of the observed thermal structure is discussed in terms of the energetics of the various regions of the middle atmosphere. It is show that the solar UV radiation plays a major role only in the energy budget of the stratosphere and the lower thermosphere. The energetics of the mesosphere is primarily influenced by the dissipation of eddy energy. The temperature in the region is a good indicator of the eddy diffusivity and can be used in deriving the eddy diffusion coefficient.

Description: The paper presents a model for contrast reduction by atmospheric haze developed for the 'two-halves' field of the earth's surface and other geometries of the earth's surface albedo. The model is based on a simplified solution of the equation of radiative transfer in two dimensions, resulting in a method for calculation of the upward zenith intensity in the atmosphere as a function of the distance from the border between the two half planes, for an unabsorbing atmosphere. The adjacency effect between two infinitesimal areas of different albedos is calculated; the resultant simplified solution is used to develop expressions for the line-spread function of the atmosphere and the modulation transfer function. The line-spread function is used to calculate the point spread function, which can be used to compute the intensity above any surface with given spatial dependence of the reflectivity.

Description: The solar power satellite concept which would make the sun's radiation available on earth as a source of energy, is discussed. Attention is given to the concept currently under evaluation in the USA, and also in Europe, though to a lesser extent. The advantages and problems associated with its adoption by the UK as a major source of electrical energy are discussed. The discussion covers topics such as sizing, reference system, and construction, costs, and problem areas.

Description: Measurement of short-lived photochemically-produced species in the stratosphere by solar occultation is difficult because the rapid variation of such species near the terminator introduces ambiguities in interpreting the measured absorption in terms of meaningful atmospheric abundances. These variations produce tangent path concentrations that are asymmetric relative to the tangent point, as opposed to the symmetrical distribution usually assumed in most inversion algorithms. Neglect of this asymmetry may yield an inverted profile that deviates significantly from the true sunset/sunrise profile. In the present paper, the influence of this effect on solar occultation measurements of ClO and NO is examined. The results show that average inhomogeneity factors, which measure the concentration variation along the tangent path and which can be calculated from a photochemical model, can indicate which species require more careful data analysis.

Description: Existing two-stream approximations to radiative transfer theory for particulate media are shown to be represented by identical forms of coupled differential equations if the intensity is replaced by integrals of the intensity over hemispheres. One set of solutions thus suffices for all methods and provides convenient analytical comparisons. The equations also suggest modifications of the standard techniques so as to duplicate exact solutions for thin atmospheres and thus permit accurate determinations of the effects of typical aerosol layers. Numerical results for the plane albedos of plane-parallel atmospheres are given for conventional and modified Eddington approximations, conventional and modified two-point quadrature schemes, the hemispheric-constant method and the delta-function method, all for comparison with accurate discrete-ordinate solutions. A new two-stream approximation is introduced that reduces to the modified Eddington approximation in the limit of isotropic phase functions and to the exact solution in the limit of extreme anisotropic scattering. Comparisons of plane albedos and transmittances show the new method to be generally superior over a wide range of atmospheric conditions (including cloud and aerosol layers), especially in the case of nonconservative scattering.

Description: With a three-parameter analytical model, the ozone profile below 10 mbar to the surface is derived from the Nimbus 4 satellite backscattered ultraviolet and infrared measurements. Comparison of the derived profiles with those observed by ozonesondes shows that gross features are satisfactorily reproduced. Meridional cross section of the ozone partial pressure derived from the satellite data reveal the significant equator-to-pole features, as well as seasonal variability. An examination of the sensitivity of the method shows that an error in infrared radiance of approximately 1 erg leads to an error of about 10 mbar in the weighted mean pressure of the ozone layer in the tropics.

Description: The role of local particle injections and accelerations in determining energetic particle spectra used as an indication of the radial diffusion of trapped magnetospheric particles is assessed. An idealized one-dimensional steady-state model of magnetospheric radial transport in which diffusion is balanced against particle sources and sinks is used to illustrate the effects of particle injection at a point and over a band of radii in which the observation point is immersed in particle spectra. For an injection spectrum uniformly distributed in space and a step function in energy, it is shown that the energy dependence of the measured spectrum is determined not only by adiabatic energization of the input spectrum but by the spatial structure of the injection and the radial dependence of the diffusion coefficient as well. The relevance of the results for observations of particle spectra in the terrestrial and Jovian magnetospheres is also considered

Description: Since 1960 three classes of zone sounders have been developed: (1) backscatter ultraviolet, (2) infrared limb and nadir radiance, and (3) stellar and solar occultation methods. With these techniques ozone has been measured from 20 to 100 km. Tropospheric ozone measurements are beyond present technology, but total ozone is determined with the backscatter ultraviolet and nadir infrared methods.

Description: (Previously cited in issue 12, p. 2037, Accession no. A81-29543)

Description: Several hundred topside ionograms were used to study simulated wave-particle interactions in the ionosphere. The study combined the benefits of high-frequency-resolution Alouette 2 analog sounder data with advanced digital graphics techniques. The study shows that the sounder phase can cause significant plasma heating when the plasma parameter is confined to specific ranges. The observations support the Harris instability generation process and the nonlinear Landau damping maintaining process for long-duration diffuse resonances. The observations also suggest that the so-called Q resonances have characteristics which imply that generation processes in a sounder-stimulated plasma turbulence may be involved.

Description: Commercially available metallurgical grade (MG) silicon has high B and P content which is not reduced significantly by directional solidification. By choosing high purity raw materials for an experimental Submerged Electrode Arc Furnace, most of the impurities are reduced to 10 ppmw. Directional solidification of upgraded metallurgical grade (UMG) silicon by the Heat Exchanger Method (HEM) has produced 16 cm x 16 cm cross section ingots with nearly single crystal structure. The main problem encountered during directional solidification was SiC impurities dispersed through the structure. Solar cells fabricated from UMG silicon that was directionally solidified twice by HEM have shown up to 12.33% (am1) conversion efficiency.

Description: A main source of high carbon levels in silicon crystals grown from melt under reduced pressures and contained in silica crucibles supported by graphite retainer/susceptor was identified by thermodynamic analysis. The calculations were verified by experimental results and the carbon level is reduced by approximately 50% with the use of molybdenum retainers.

Description: The most developed process for silicon crystal growth is the Czochralski (CZ) method which was in production for over two decades. In an effort to reduce cost of single crystal silicon for photovoltaic applications, a directional solidification technique, Heat Exchanger Method (HEM), was adapted. Materials used in HEM and CZ furnaces are quite similar (heaters, crucibles, insulation, etc.). To eliminate the cost of high purity argon, it was intended to use vacuum operation in HEM. Two of the major problems encountered in vacuum processing of silicon are crucible decomposition and silicon carbide formation in the melt.

Description: The Fixed Abrasive Slicing Techniques (FAST) is a new slicing technique that was developed to slice ingots more effectively. It was demonstrated that 25 wafers/cm can be sliced from 10cm diameter and 19 wafers/cm from 15 cm diameter ingots. Over 99% yield (222 out of a possible 224) was demonstrated during slicing of a 10 cm diameter ingots at 25 wafers/cm. The average thickness of wafers was 0.249 mm and the kerf was 0.151 mm. Slicing rates as high as 0.14 mm/min were also demonstrated for 10 cm diameter ingots.

Description: One of the major cost factors in silicon ingot technology adaptation for terrestrial photovoltaic application is in slicing boules into wafers. The most developed industrial practice is the Internal Diameter (ID) slicing. This method utilizes diamond cutting. The diamond stands up for long periods, hence, the cost of expendable materials is low. However, the ID technology as practiced today has poor material utilization. The Multiblade Slurry (MBS) method has low equipment and labor costs but its expendable material costs are high. Recently Multiwire Slurry (MWS) technology has shown very good material utilization, but its expendable material costs are even higher than MBS. The multiwire Fixed Abrasive Slicing Technique (FAST) still in advanced development stage, combines the low expendable material costs of ID method, the low labor and equipment costs of MBS and high material utilization of MWS.

Description: Directional solidification by the Heat Exchanger Method (HEM) is a viable approach for directional solidification of silicon ingots used for terrestrial solar cell applications. Some of the significant advances made during this phase of the program were: ingot size, 34 cm x 34 cm x 17 cm - 45 kg, usable material yield - 90%, solar cell efficiency averaged over the whole ingot - 85% of control CZ (35 kg ingot), very uniform resistivity over the boule, and cycle time for 36 kg ingots - 56 hours. Some of the problems encountered were growth rate decrease with increased ingot height, silicon carbide precipitates, and high dislocation density in HEM material. The silicon carbide is attributed to backstreaming of oil vapors from the vacuum pump; the high dislocation density is associated with the thermal history of the boule.

Description: The economic advantages of solar dish collectors are evaluated and compared with other energy systems. Labor, inflation and energy deregulation are considered.

Description: Solar energy systems were investigated which complement nuclear and coal technologies as a means of reducing the U.S. dependence on imported petroleum. Solar Thermal Energy Systems (STES) represents an important category of solar energy technologies. STES can be utilized in a broad range of applications servicing a variety of economic sectors, and they can be deployed in both near-term and long-term markets. The net present value of the energy cost savings attributable to electric utility and IPH applications of STES were estimated for a variety of future energy cost scenarios and levels of R&D success. This analysis indicated that the expected net benefits of developing an STES option are significantly greater than the expected costs of completing the required R&D. In addition, transportable fuels and chemical feedstocks represent a substantial future potential market for STES. Due to the basic nature of this R&D activity, however, it is currently impossible to estimate the value of STES in these markets. Despite this fact, private investment in STES R&D is not anticipated due to the high level of uncertainty characterizing the expected payoffs.

Description: The integration and check-out of a complete Dish Solar Stirling Thermal Power System is described. The preliminary results of the tests conducted thus far are presented. The results are very encouraging and show promise of high performance and efficiency. The outstanding performance and durability of the 4-95 Stirling engine was the highlight of this 6 month integration and test activity. Exposure to severe heat, dust, sand and wind during the summer months and heavy rains, high winds, including sand storms and freezing cold in recent months did affected the engine or the receiver in any noticable manner.

Description: The Jay Carter Enterprises (JCE) Paratransit Vehicle steam engine was tested over a range of conditions which might be experienced by the power converter subsystem of the Small Community Solar Thermal Power Experiment. Some difficulties were encountered getting the engine ready for testing. These difficulties were related to the five year dormancy of the entire system and to incomplete development work that had been going on at the time of cessation of steam engine work at JCE. Other difficulties were related to the fact that the particular expander being tested never ran before and possessed some manufacturing defects. Nevertheless, the engine was operated successfully and results of testing do verify results of computer simulations of the engine in regard to the effect of temperature and power level variations. Engine efficiency was good but generally lower than expected and performance dropped as testing continued. The effect of change in expansion ratio was not demonstrated because of deterioration in engine performance. Post-test inspection revealed numerous correctable defects.

Description: A study was performed by AiResearch Manufacturing Company, a division of The Garrett Corporation, on the development a high-temperature ceramic heat exchanger element to be integrated into a solar receiver producing heated air. A number of conceptual designs were developed for heat exchanger elements of differing configuration. These were evaluated with respect to thermal performance, pressure drop, structural integrity, and fabricability. The final design selection identified a finned ceramic shell as the most favorable concept. The shell is surrounded by a larger metallic shell. The flanges of the two shells are sealed to provide a leak-tight pressure vessel. The ceramic shell is to be fabricated by an innovative combination of slip casting the receiver walls and precision casting the heat transfer finned plates. The fins are bonded to the shell during firing. The unit is sized to produce 2150 F ar at 2.7 atm pressure, with a pressure drop of about 2 percent of the inlet pressure. This size is compatible with a solar collector providing a receiver input of 85 kw(th). Fabrication of a one-half scale demonstrator ceramic receiver has been completed.

Description: The modifications and testing of a standard Stirling engine, required for connection to a 25 kW induction alternator, for use with a solar thermal parabolic dish electric module is described. Power was absorbed by a GE induction alternator connected to the utility grid. Also included are the results from recent testing of another solar engine at the DOE-Georgia Tech solar site. It was done in parallel with the testing at Edwards for the purpose of comparing performance of two solar-only receivers, which were based on the standard 4-95 involute heat exchanger.

Description: Verification testing of a solar collector was undertaken prior to its operation as part of an industrial process heat plant at Capitol Concrete Products in Topeka, Kansas. Testing was performed at a control plant installed at Sandia National Laboratory, Albuquerque, New Mexico (SNLA). Early results show that plant performance is even better than anticipated and far in excess of test criteria. Overall plant efficiencies of 65 to 80 percent were typical during hours of good insolation. A number of flaws and imperfections were detected during operability testing, the most important being a problem in elevation drive alignment due to a manufacturing error. All problems were corrected as they occurred and the plant, with over 40 hours of operation, is currently continuing operability testing in a wholly-automatic mode.

Description: The development and preliminary test results for an air-cooled, hermetically sealed 20 kW sub E organic Rankine cycle engine/alternator unit for use with point focussing distributed receiver solar thermal power system. A 750 F toluene is the working fluid and the system features a high speed, single-stage axial flow turbine direct-coupled to a permanent magnet alternator. Good performance was achieved with the unit in preliminary tests.

Description: The development of a point-focus Fresnel lens solar concentrator for high-temperature solar thermal energy system applications is discussed. The concentrator utilizes a transmittance-optimized, short-focal-length, dome-shaped refractive Fresnel lens as the optical element. This concentrator combines both good optical performance and a large tolerance for manufacturing, deflection, and tracking errors. The conceptual design of an 11-meter diameter concentrator which should provide an overall collector efficiency of about 70% at an 815 C (1500 F) receiver operating temperature and a 1500X geometric concentration ratio (lens aperture area/receiver aperture area) was completed. Results of optical and thermal analyses of the collector, a discussion of manufacturing methods for making the large lens, and an update on the current status and future plans of the development program are included.

Description: Estimates are made showing that, as a consequence of rocket activity in the earth's upper atmosphere in the Shuttle era, average ice nuclei concentrations in the upper atmosphere could increase by a factor of two, and that an aluminum dust layer weighing up to 1000 tons might eventually form in the lower atmosphere. The concentrations of Space Shuttle ice nuclei (SSIN) in the upper troposphere and lower stratosphere were estimated by taking into account the composition of the particles, the extent of surface poisoning, and the size of the particles. Calculated stratospheric size distributions at 20 km with Space Shuttle particulate injection, calculated SSIN concentrations at 10 and 20 km altitude corresponding to different water vapor/ice supersaturations, and predicted SSIN concentrations in the lower stratosphere and upper troposphere are shown.