ALBERT

Description: Flow visualization is a powerful tool for characterizing fluid dynamics within engineering systems that utilize fluid working media. Recent advances in Positron Emission Tomography (PET) have enhanced its ability to extend beyond the medical field, and offer an alternate vantage point in visualizing optically inaccessible fluid distributions and flow fields within the aerospace field. In light of this prospect an investigation has ensued to parametrically bound the flows that can be sufficiently resolved using current PET technology. Preliminary results from on going simulations and analyses will be presented.

Description: A database of heating and pressure measurements on a 7-deg half-angle cone in a highenthalpy expansion tunnel in CO2 has been generated to support development and validation of computational models to be employed in the design of future Mars missions. Laminar, transitional, and turbulent simulations were performed at the test conditions for comparisons with the data. Close agreement was obtained for both fully-laminar and fully turbulent conditions. For the remaining transitional/turbulent conditions, agreement to within, or slightly more than, the estimated experimental uncertainty was demonstrated. The influence of transition intermittency and transition length models on predicted heating levels was demonstrated, as were differences in turbulent heating predictions generated using various algebraic, one-equation, and two-equation turbulence models. These comparisons provide some measure of confidence in turbulent simulation capabilities; however, because the data were not obtained on a relevant entry vehicle geometry, it is not possible to fully quantify computational uncertainties for the definition of Mars mission aerothermodynamic environments at this time

Description: To study the azimuthal development of boundary-layer instabilities, a controlled, laser-generated perturbation was created in the freestream of the Boeing/U.S. Air Force Office of Scientific Research Mach 6 Quiet Tunnel. The freestream perturbation convected downstream in the wind tunnel to interact with a flared-cone model. The flared cone is a body of revolution bounded by a circular arc with a 3 m radius. Pressure transducers were used to measure a wave packet generated in the cone boundary layer by the freestream perturbation. Nine of these sensors formed three stations of azimuthal arrays and were used to determine the azimuthal variation of the wave packets in the boundary layer. The freestream laser-generated perturbation was positioned upstream of the model in three different configurations: along the centerline axis, offset from the centerline axis by 1.5 mm, and offset from the centerline axis by 3.0 mm. When the freestream perturbation was offset from the centerline of a flared cone with a 1.0 mm nose radius, a larger wave packet was generated on the side toward which the perturbation was offset. As a result, transition occurred earlier on that side. The offset perturbation did not have as large of an effect on the boundary layer of a nominally sharp flared cone.

Description: Researchers at NASA Ames in California have built a new facility that uses multiple 50-kW continuous wave lasers to add the capability for simulating radiative heating on thermal protection materials. The new facility, the Laser Enhanced Arc-jet Facility (LEAF-Lite), was added to NASA Amess Interaction Heating Facility arc-jet and now allows for test articles to be heated by both convective and radiative heat flux, making the facility more like flight. Using this new system, researchers can now simulate radiant heating with the laser and convective heating with the arc-jet simultaneously on a single test article. During its initial test in October 2017, the lasers radiatively heated a 6 x 6 Avcoat wedge sample to 405 W/sq.cm while the arc-jet simultaneously provided 160 W/sq.cm of convective heat, resulting in a total heat flux of 565 W/sq.cm. Radiative heating is more prevalent in missions with higher atmospheric entry speeds like the Orion space capsule or interplanetary scientific probes. Later this year, scientists will expand the spot size to cover 17 x 17 to test an Orion TPS panel.

Description: The near and very near wake of a thin flat plate with a circular trailing edge are investigated with direct numerical simulations (DNS). Data obtained for two different Reynolds numbers (based on plate thickness, D) are the main focus of this study. The separating boundary layers are turbulent in both cases. An earlier investigation of one of the cases (Case F) showed shed vortices in the wake that were about 1.0 D to 4.0 D in spanwise length. Considerable variation in both the strength and frequency of these shed vortices was observed. One objective of the present investigation is to determine the important contributors to this variability in strength and frequency of shed vortices and their finite spanwise extent. Analysis of the data shows that streamwise vortices in the separating boundary layer play an important role in strengthening/weakening of the shed vortices and that high/low-speed streaks in the boundary layer are important contributors to variability in shedding frequency. Both these features of the boundary layer contribute to the finite extent of the vortices in the spanwise direction. The second plate DNS (Case G, with 40 percent of the plate thickness of Case F) shows that while shedding intensity is weaker than obtained in Case F, many of the wake features are similar to that of Case F. This is important in understanding the path to the wake of the thin plate with a sharp trailing edge where shedding is absent. Here we also test the efficacy of a functional relationship between the shedding frequency and the Reynolds numbers based on the boundary layer momentum thickness (Re (sub theta) and D (Re (sub D)); data for developing this behavioral model is from Cases F & G and five earlier DNSs of the flat plate wake.

Description: To experimentally assess and compare the mixing performance of high-speed fuel injectors for scramjet engines, quantitative global metrics are needed. The one-dimensional metric most commonly used to assess the degree of mixing completeness at a given downstream station is the mixing efficiency parameter. The experimental determination of the mixing efficiency parameter requires measurement of the spatial distributions of both the fuel mass fraction and the mass flux. Standard in-stream gas sampling techniques can be used to measure the fuel mass fraction distribution, however the mass flux distribution is not easily determined experimentally because it requires the measurement of three independent aerothermodynamic variables in addition to the mixture composition. For this reason, several metrics that can be calculated from the fuel distribution alone are commonly used to assess mixing performance. Because these other metrics do not provide a mass flux-weighted measure of the local degree of mixing completeness, they may not correlate well with the mixing efficiency parameter. Therefore, if the substitute metrics are to be used to compare the mixing performance of candidate fuel injector concepts, it is important to understand their relationships to the mixing efficiency parameter in a representative scramjet combustor flowfield. This work investigates the relationships between the mixing efficiency parameter and several substitute metrics that are able to be measured with the current experimental setup of the Enhanced Injection and Mixing Project at the NASA Langley Research Center for baseline strut and ramp injectors. The results of these comparisons have revealed that it is possible to glean different (i.e., incorrect) conclusions about which injector is the better mixer when the substitute mixing performance metrics are used instead of the mixing efficiency parameter, thereby highlighting the importance of mass flux-weighted mixing performance metrics.

Description: The objective of the Heatshield for Extreme Entry Environment Technology (HEEET) projects is to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations such as Venus and Saturn. Destinations that have extreme entry environments with heat fluxes up to 5000 watts per square centimeter and pressures up to 5 atmospheres, entry environments that NASA has not flown since Pioneer-Venus and Galileo. The scope of the project is broad and can be split into roughly four areas, Manufacturing/Integration, Structural Testing and Analysis, Thermal Testing and Analysis and Documentation. Manufactruing/Integration covers from raw materials, piece part fabrication to final integration on a 1-meter base diameter 45-degree sphere cone Engineering Test Unit (ETU). A key aspect of the project was to transfer as much of the manufacturing technology to industry in preparation to support future mission infusion. The forming, infusion and machining approaches were transferred to Fiber Materials Inc. and FMI then fabricated the piece parts from which the ETU was manufactured. The base 3D-woven material consists of a dual layer weave with a high density outer layer to manage recession in the system and a lower density, lower thermal conductivity inner layer to manage the heat load. At the start of the project it was understood that due to weaving limitations the heat shield was going to be manufactured from a series of tiles. And it was recognized that the development of a seam solution that met the structural and thermal requirements of the system was going to be the most challenging aspect of the project. It was also recognized that the seam design would drive the final integration approach and therefore the integration of the ETU was kept in-house within NASA. A final seam concept has been successfully developed and implemented on the ETU and will be discussed. The structural testing and analysis covers from characterization of the different layers of the infused material as functions of weave direction and temperature, to sub-component level testing such as 4-pt bend testing at sub-ambient and elevated temperature. ETU test results are used to validate the structural models developed using the element and sub-component level tests. Given the seam has to perform both structurally and aerothermally during entry a novel 4-pt bend test fixture was developed allowing articles to be tested while the front surface is heated with a laser. These tests are intended to establish the system's structural capability during entry. A broad range of aerothermal tests (arcjet tests) are being performed to develop material response models for predicting the required TPS thickness to meet a mission's needs and to evaluate failure modes. These tests establish the capability of the system and assure robustness of the system during entry. The final aspect of the project is to develop a comprehensive Design and Data Book such that a future mission will have the information necessary to adopt the technology. This presentation will provide an overview and status of the project and describe the status of the tehnology maturation level for the inner and outer planet as well as earth entry sample return missions.

Description: The flow behind two rectangular roughness elements with a height approximately 38-41 percent of the boundary layer thickness was examined with a hot-wire probe. The rectangular roughness elements are oriented so that one element was at a plus 45-degree angle relative to the leading edge of the plate. A second roughness element was placed 7.16 millimeters downstream of the first one with either the same orientation relative to the leading edge of the plate, or an opposing orientation of minus 45 degrees from the leading edge. Mean mass-flux and total-temperature profiles of the flow field downstream of the tandem roughness elements were examined for mean-flow distortion. Using streak strength as a measure of mean-flow distortion, the tandem roughness elements had approximately the same amount of distortion, regardless of their relative orientation. Mass-flux fluctuation profiles show that the dominant mode downstream of the tandem roughness elements with the same orientation was similar to that of a single roughness element and centered at a frequency of approximately 55 kilohertz (kHz). The dominant instability downstream of the tandem roughness elements with opposing orientation was centered at a frequency of 65 kHz and grew more slowly than the instabilities behind the single roughness element.

Description: Computational Fluid Dynamics (CFD) analysis is performed to investigate liquid blockage in the helium pressure line associated with the propellant (MMH) tank. If a certain amount of propellant is trapped within the helium pressure line, the question is whether the given amount of helium that is available can provide a clear helium flow path with no adverse consequences such as over pressurization of the pressure line.

Description: In this work, a one-dimensional methodology for simulating shock tubes is developed. The model accounts for the viscous interactions of the shock with the shock tube wall by adding an area change source term in the 1-D conservation equations corresponding to the boundary layer growth. This source term corresponds to the mass and energy going into the boundary layer. The boundary layer growth is computed using a simple model with a scaling factor. This scale factor is used to tailor a solution to match the deceleration profile of a shock tube test. In doing so, not only will the source term take into account boundary layer losses, it will also cover any effect due to radiative cooling loses from the gas. For this study, the Electric Arc Shock Tube(EAST) facility at NASA Ames Research Center is modeled for Earth reentry conditions. The purpose of this paper is to investigate if anomalies identified for certain conditions in the EAST data are due to shock deceleration. These anomalies include measuring electron number density above equilibrium predictions and observing that radiance profiles can continually increase behind the shock, never reach steady state, for certain shots (typically those less than 10 km/s). An eleven species air mixture is chosen to study the chemistry of the flow. Comparisons of the simulations to the experimental results are presented. Good agreement with the shock deceleration profiles was achieved by tuning in the boundary layer scale factor. The temperature as well as electron number density increases behind the shock, as has also been observed in the experiments. Finally, radiance comparisons between results from NEQAIR and experiments also show good agreement for some shots, but significant discrepancies are still observed for others.

Description: The External Active Thermal Control System (EATCS) provides cooling for all pressurized modules and the main Power Distribution Electronics (PDE) on the International Space Station (ISS). There are 2 EATCS loops (Loop A and Loop B) which includes 3 deployable radiators. Each deployable radiator contains 2 flow paths to provide heat rejection.Telemetry monitoring identified a coolant (liquid ammonia) leak in EATCS Loop B. Robotic External Leak Locator (RELL) scans found higher concentrations of vaporous ammonia near the EATCS Loop B Radiator #3 Flow Path #2. On May 3, 2017, the EATCS Loop B Radiator #3 Flow Path #2 was isolated and vented. As of the data to date, the ammonia leak has ceased. The purpose of this presentation is to discuss the analysis for venting the EATCS Loop B Radiator #3 Flow Path #2. Venting analysis is performed to determine the worst case time to empty the flow path and maximum thrusts imposed on the ISS. Flight controllers and engineers in the Mission Control Center (MCC) uses this data to develop operational procedures and perform the vent safely. It was predicted that the worst case time to empty the EATCS Loop B Radiator #3 Flow Path #2 was ~ 60 minutes. The predicted maximum thrusts were ~ 11 lbf (49 N) at the start of the vent and ~10 lbf (45 N) after the system reaches saturation.The vent was successfully performed and took ~ 20 minutes to empty the EATCS Loop B Radiator #3 Flow Path #2. Using telemetry from the day of the vent, analysis determined the time to empty the EATCS Loop B Radiator #3 Flow Path #2 would be ~13 minutes. The predictive analysis used worst case inputs and assumptions which bounded the actual results. Telemetry is not available to correlate actual thrust with the predicted maximum thrusts. However, by using Russian Thrusters for ISS attitude control, attitude control telemetry indicated the flight attitude was maintained.

Description: Radiative heating computations are performed for a range of high speed Earth entry experiments conducted in the Electric Arc Shock Tube at NASA Ames. The nonequilibrium radiative transport equations are solved in NEQAIR using flow field variables from the full facility CFD simulations of the EAST shock tube performed by US3D ow solver. These physics-based flow calculations lead to a significantly different post-shock gas state and associated radiation field as compared to that based on a simplified but computationally inexpensive calculation for flow over a blunt-body with appropriate initial conditions. The radiation spectra and radiance profiles are computed for an extensive range of wavelengths, from deep VUV to IR, which are pertinent to the emission characteristics of high enthalpy shock waves in air. The radiation properties of the shocked gas are calculated both in the nonequilibrium region at the shock, and in the equilibrium region behind the shock. Numerical predictions are found to be consistent with the experimental observations.

Description: Large space structures are capable of large thermal deformations in the space environment. A case of large-scale thermal deformation was observed in the analysis of the Near Earth Asteroid Scout solar sail, with predicted tip displacements of more than one meter in seven-meter booms. Experimental data supports the broad conclusions of the analysis, but shows poor agreement on the details of the thermal deformation. Prediction that is precise enough to drive engineering decisions will require coupled thermal-stress analysis with features that are not found in current multiphysics codes. This paper describes a simple method for stepwise coupling between commercial nonlinear stress analysis software and radiative thermal analysis software. Results are presented for a round stainless steel tube, which is a common case in existing literature.

Description: No abstract available

Description: AFRC (Armstrong Flight Research Center) has a long history, and a lot of lessons learned, in testing hypersonic structures. This poster describes hypersonic structures, how to test them, and the methods used to develop the testing.

Description: The high power density of emerging electronic devices is driving the transition from remote cooling, which relies onconduction and spreading, to embedded cooling, which extracts dissipated heat on-site. Two-phase microgap coolersemploy the forced flow of dielectric fluids undergoing phase change in a heated channel within or between devices. Such coolers must work reliably in all orientations for a variety of applications (e.g., vehicle-based equipment), as well as in microgravity and high-g for other applications (e.g., spacecraft and aircraft). The lack of acceptable models andcorrelations for orientation- and gravity-independent operation has limited the use of two-phase coolers in suchapplications. Previous research has revealed that gravitational acceleration plays a diminishing role in establishing flow regimes and transport rates as the channel size shrinks, but there is considerable variation among the proposed microscale criteria and limited research on two-phase flows in low aspect ratio microgap channels. Reliable criteria for achieving orientation- and gravity-independent flow boiling would enable emerging systems to exploit this thermal management technique and streamline the technology development process.

Description: Presentation on intern rotations. Summer 2013 I worked in cryolab and learned about calorimitry testing. Spring 2014 I helped create themalcouple arm for GODU-LH2. Summer 2014 I assisted with hardware failures on GPIM fracture mechanics testing. Summer 2017 I created a qualification test plan and test fixture to test vacuum seal-off valves.

Description: This paper describes an experimental investigation of the effect of the gravity pressure head on the startup of a heat pipe under the reflux mode. In this study, a heat pipe with internal axial grooves was placed in an upright position with two different tilt angles relative to the horizontal plane. Heat was applied to the evaporator at the bottom and cooling was provided to the condenser at the top. The liquid-flooded evaporator was divided into seven segments along the axial direction, and electrical heaters were attached to each segment. Heat was applied to individual heaters in various combinations and sequences. Test results show that as long as an individual evaporator segment was flooded with liquid initially, a superheat was required to vaporize the liquid in that segment. The amount of superheat required for liquid vaporization was a function of gravity pressure head imposed on that evaporator segment. The most effective way to start the heat pipe was to apply a heat load with a high heat flux to the lowest segment of the evaporator. This paper describes an experimental investigation of the effect of the gravity pressure head on the startup of a heat pipe under the reflux mode. In this study, a heat pipe with internal axial grooves was placed in an upright position with two different tilt angles relative to the horizontal plane. Heat was applied to the evaporator at the bottom and cooling was provided to the condenser at the top. The liquid-flooded evaporator was divided into seven segments along the axial direction, and electrical heaters were attached to each segment. Heat was applied to individual heaters in various combinations and sequences. Test results show that as long as an individual evaporator segment was flooded with liquid initially, a superheat was required to vaporize the liquid in that segment. The amount of superheat required for liquid vaporization was a function of gravity pressure head imposed on that evaporator segment. The most effective way to start the heat pipe was to apply a heat load with a high heat flux to the lowest segment of the evaporator.

Description: The eect of a forward-facing step on stationary crossow transition was studied using standard stereo particle image velocimetry (PIV) and time-resolved PIV. Step heights ranging from 53 to 71% of the boundary-layer thickness were studied in detail. The steps above a critical step height of approximately 60% of the boundary-layer thickness had a signicant impact on the stationary crossow growth downstream of the step. For the critical cases, the stationary crossow amplitude grew suddenly downstream of the step, decayed for a short region, then grew again. The adverse pressure gradient upstream of the step resulted in a region of crossow reversal. A secondary set of vortices, rotating in the opposite direction to the primary vortices, developed underneath the uplifted primary vortices. The wall-normal velocity disturbance (V' ) created by these secondary vortices impacted the step, and is believed to feed into the strong vortex that developed downstream of the step. A large but very short negative crossow region formed for a short region downstream of the step due to a sharp inboard curvature of the streamlines near the wall. For the larger step height cases, a crossow-reversal region formed just downstream of the strong negative crossow region. This crossow reversal region is believed to play an important role in the growth of the stationary crossow vortices downstream of the step, and may be a good indication of the critical forward-facing step height.

Description: Given input sources of uncertainty, non-intrusive uncertainty propagation methods quantify the uncertainty in output quantities of interest (QoI) by performing a nite number of CFD (Computational Fluid Dynamics) instance realizations needed in the calculation of output statistics. It is well known that this introduces multiple sources of error. CFD codes often utilize finite-dimensional approximation (grids, basis functions, etc.) thus incurring CFD numerical errors often approximately reinterpreted as a statistical bias. Uncertainty propagation methods calculate uncertainty statistics for output quantities of interest using a numerical method (e.g. deterministic quadrature, sampling, etc.) thus incurring UQ (Uncertainty Quantification) numerical errors. Importance of quantifying these errors in large scale scientific computing: How accurate is an output statistic?; How should additional computational resources be invested to further reduce the error in a statistic?

Description: This paper will present analysis to evaluate a functional form and associated parameters to determine the radiative heating at various back-shell locations of the Mars 2020 aeroshell. The radiative heating indicators are used for preliminary vehicle design, and to determine the worst-case trajectories for peak radiative heat flux and load. Historically, the functional form for radiative heating is based on free-stream parameters of density, velocity and a length scale, typically the nose-radius (or equivalent). However, a fit of this form has been shown to not provide significant enough accuracy when compared to simulation results. Therefore, a fit based on post-shock equilibrium calculations of CO and CO2 number density, temperature and pressure has been devised. The results from the TPS 15 01 trajectory were used to develop the fit. The fit was then applied to the MSL best estimated trajectory (BET). Furthermore, the paper will quantify the uncertainty in simulations of the radiative heating for Mars 2020.

Description: Keynote presentation highlighting aerothermal modeling needs for EDL, with specific emphasis on areas where improved ground test diagnostics and instrumentation could help.

Description: Line Chill-down heat transfer was modelled using SINDA/FLUINT. Multiple chill-down tests were modelled using the heat transfer correlations that are available in SINDA/FLUINT, as well as incorporating heat transfer empiricisms developed by the University of Florida1 based on a series of liquid nitrogen chill-down tests. The chill-down tests that were modelled were the liquid nitrogen tests conducted by the University of Florida1 as well as liquid hydrogen tests conducted by NASA Glenn Research Center2. The liquid nitrogen tests included horizontal flow, upward flow, and downward flow with the liquid Reynolds Numbers ranging 850 - 231,000. The liquid hydrogen test was vertical upward flow at a Reynolds Number range of 18,400 - 433,000. Both the University of Florida's heat transfer correlations and SINDA/FLUINT's internal correlations faired similarly to wall temperature test data. They were acceptable although improvements could be made to the University of Florida correlations as well and SINDA/FLUINT's internal correlations.

Description: Spectrally and spatially resolved radiance has been measured in the Electric Arc Shock Tube (EAST) facility, with the aim of improving fundamental understanding of high enthalpy flows in pure nitrogen. These tests provide data to inform models used for simulations of high speed flight in nitrogen rich atmospheres, such as Earth or Titan. The experiments presented in this paper cover conditions from approximately 6 km/s to 11 km/s at an initial pressure of 0.2 Torr. A wide range of physics, with different degrees of non-equilibrium and nitrogen dissociation, are covered. The EAST data are presented in different formats for analysis and comparisons. These formats include the spectral radiance at equilibrium (where appropriate), the spatial dependence of radiance over defined wavelength ranges and the mean non-equilibrium spectral radiance (the so-called "spectral non-equilibrium metric"). All the information needed to simulate each experimental trace, including free-stream conditions, shock time of arrival (i.e. x-t) relation, and the spectral and spatial resolution functions, are provided. Equilibrium radiation calculations are shown as a reference. It is the intention of this paper to motivate code comparisons benchmarked against this data set.

Description: No abstract available

Description: Line chill-down is an important process in cryogenic tank propellant management, storage, and usage Complex flow dynamics during these processes: boiling heat transfer (film, transition, and nucleate) Understanding boiling phenomena can lead to efficient line chill-down systems that use less propellant, propellant stored, reducing cost for space missions Line Chill-down heat transfer was modelled using SINDA/FLUINT version 5.8 (SF) Multiple chill-down tests were modelled using: heat transfer correlations readily available in SF using HTN/HTC TIES heat transfer empiricisms developed by the University of Florida (UF) based on a series of liquid nitrogen chill-down tests using SF HTU TIES Chill-down tests modelled: liquid nitrogen tests conducted by the University of Florida horizontal flow, upward flow, and downward flow (Reynolds Numbers ranging 850-231,000)liquid hydrogen tests conducted by NASA Glenn Research Center vertical upward flow (Reynolds Number range of 18,400 - 433,000)The flow rate was measured far downstream of the test section, near the system exit. Where to set the flow rate? SF was highly sensitive, and sometime unstable, setting the test flow rate downstream (the outlet) of the test section model and setting the test pressure upstream (the inlet) of the test section model higher flow rate oscillations at the entrance of the model's test section SF was more stable setting the test flow rate upstream (than the downstream flow rate set case)test pressure was used as an inlet (SF plenum) to set the thermodynamic state (temperature and quality) coming into the system setting the appropriate downstream pressure was the unknown. The pressure drops predicted by SF for the downstream set flow rate boundary condition were much smaller than test section measured pressure drops. The multiphase pressure drop correlations used internally in SF may need to be adjusted. Models with an upstream flow rate set assumed a pressure drop that was small

Description: Real time nondestructive evaluation is required for composites load testing. The early detection and measurement of damage progression is important to understand failure modes. A single stringer panel was subjected to quasi-static loading to induce deformation which can result in the formation of delamination damage between the stiffener flange and skin. Passive thermography was used to detect damage in real time as a function of the applied load. The loading was stopped when damage growth was detected. Of particular interest was the early detection of damage formation which can be challenging, as compared to cyclic fatigue loading. Passive thermography data were acquired and processed in real time and revealed damaged areas due to heating from fiber breakage and delamination formation. The processed thermal imagery was also compared to acoustic emission and ultrasound data.

Description: No abstract available

Description: Despite decades of development of unstructured mesh methods, direct numerical simulations (DNS) of turbulent flows are still predominantly performed on structured or unstructured hexahedral meshes with high-order finite-difference methods, weighted essentially nonoscillatory (WENO) schemes, or hybrid schemes formed by their combinations. Tetrahedral meshes offer easy mesh generation and adaptation around complex geometries and the potential of an orientation-free grid that would benefit the isotropic nature of small-scale dissipation, as well as the solution accuracy of intermediate scales. To advance the state of the art of unstructured-mesh simulation capabilities for shock/turbulence interaction, DNS using pure tetrahedral meshes are carried out with the space-time conservation element, solution element (CESE) method in this research. By its design, the CESE method is constructed based on a non-dissipative scheme and is a genuinely multidimensional numerical framework that is free from the use of an approximate Riemann-solver. The numerical framework also provides the ability to add numerical dissipation (the nondissipative scheme acts as the reference state like that of the reversible state in thermodynamics) when needed (with justification from mathematics/physics). The above-mentioned features along with the CESE method's consistent shock-capturing approach and strong enforcement of flux conservation in spacetime offers a novel method to accurately simulate turbulent flows and their interaction with shocks using tetrahedral meshes. Two canonical problems, namely, isotropic turbulence interaction with a normal shock and a Mach 2.9 turbulent boundary layer flow over a 24deg compression corner are investigated in this study. Computational results show reasonably good agreement with experimental data and results from structured-mesh, high-order simulations available in the literature. Successful validation of these canonical problems demonstrated here paves the way for future high-fidelity supersonic flow simulations involving complex-geometries.

Description: While low disturbance ("quiet") hypersonic wind tunnels are believed to provide more reliable extrapolation of boundary layer transition behavior from ground to flight, the presently available quiet facilities are limited to Mach 6, moderate Reynolds numbers, low freestream enthalpy, and subscale models. As a result, only conventional ("noisy") wind tunnels can reproduce both Reynolds numbers and enthalpies of hypersonic flight configurations, and must therefore be used for flight vehicle test and evaluation involving high Mach number, high enthalpy, and larger models. This article outlines the recent progress and achievements in the characterization of tunnel noise that have resulted from the coordinated effort within the AVT-240 specialists group on hypersonic boundary layer transition prediction. New Direct Numerical Simulation (DNS) datasets elucidate the physics of noise generation inside the turbulent nozzle wall boundary layer, characterize the spatiotemporal structure of the freestream noise, and account for the propagation and transfer of the freestream disturbances to a pitot-mounted sensor. The new experimental measurements cover a range of conventional wind tunnels with different sizes and Mach numbers from 6 to 14 and extend the database of freestream fluctuations within the spectral range of boundary layer instability waves over commonly tested models. Prospects for applying the computational and measurement datasets for developing mechanism-based transition prediction models are discussed.

Description: In this work, a one-dimensional methodology for simulating shock tubes is developed. The model accounts for the viscous interactions of the shock with the shock tube wall by adding an area change source term in the 1-D conservation equations corresponding to the boundary layer growth. This source term corresponds to the mass and energy going into the boundary layer. The boundary layer growth is computed using a simple model with a scaling factor. This scale factor is used to tailor a solution to match the deceleration profile of a shock tube test. In doing so, not only will the source term take into account boundary layer losses, it will also cover any effect due to radiative cooling loses from the gas. For this study, the Electric Arc Shock Tube(EAST) facility at NASA Ames Research Center is modeled for Earth reentry conditions. The purpose of this paper is to investigate if anomalies identified for certain conditions in the EAST data are due to shock deceleration. These anomalies include measuring electron number density above equilibrium predictions and observing that radiance profiles can continually increase behind the shock, never reach steady state, for certain shots (typically those less than 10 km/s). An eleven species air mixture is chosen to study the chemistry of the flow. Comparisons of the simulations to the experimental results are presented. Good agreement with the shock deceleration profiles was achieved by tuning in the boundary layer scale factor. The temperature as well as electron number density increases behind the shock, as has also been observed in the experiments. Finally, radiance comparisons between results from NEQAIR and experiments also show good agreement for some shots, but significant discrepancies are still observed for others.

Description: Adaptive Mesh Refinement (AMR) promises a much more computationally efficient means to obtain a discrete approximation to a continuous boundary value problem of a specified accuracy than classic isotropic grid refinement. The AMR capability of OVERFLOW (a computational fluid dynamics (CFD) code) is utilized to provide estimates of the exact analytical solutions to problems of interest to turbulence modeling. Predictions of surface pressure and skin friction, essentially the state of stress at the surface, shows little difference with grids believed to be "grid resolved." Velocity profiles, on the other hand, show marked differences in flows with shocks. The AMR method, as implemented in OVERFLOW 2.2k, appears to provide the ability to produce arbitrarily accurate solutions at a predictable cost much smaller than classic uniform mesh refinement.

Description: The Neutral Buoyancy Laboratory (NBL) is a 102 x 202 x 40-foot-deep tank holding over 6 million gallons of water used to simulate weightlessness for Astronaut training. The maxim "Train Like You Fly" refers to the desire to have the suit perform, during training, as close as possible to how it performs during an Extra-Vehicular Activity (EVA), particularly with respect to mobility. Therefore, the Space Suit Assembly (SSA) used in the NBL is a downgraded hardware version of the flight SSA; it is not designed for the NBL environment or operations. A classification system defines the flight Space Suit Assembly hardware as Class I, and the NBL training hardware SSA as Class IIIW. On July 20, 2017, during a manned training event in the NBL, the SSA was inadvertently over-pressurized to 22 psid; normal operating pressure being 4.3 psid. The suit subject was removed from the suit with no injury. The event was investigated by a NASA Mishap Team. The Team investigated common causes and differences between the Class I and Class IIIW Extra-vehicular Mobility Unit (EMU). The investigation determined that the event was limited to Class IIIW hardware and its external flow-controlled open loop ventilation systems. The flight EMU is a pressure regulated closed loop ventilation system. This paper will examine the differences between the Class I and Class IIIW SSA hardware and provide details of the Mishap Investigation. Corrective actions taken to mitigate risk with hardware, operations, and hazard documentation will be discussed.

Description: In the absence of body forces such as gravity, a heat pipe will start as soon as its evaporator temperature reaches the saturation temperature. If the heat pipe operates under a reflux mode in ground testing, the liquid puddle will fill the entire cross sectional area of the evaporator. Under this condition, the heat pipe may not start when the evaporator temperature reaches the saturation temperature. Instead, a superheat is required in order for the liquid to vaporize through nucleate boiling. The amount of superheat depends on several factors such as the roughness of the heat pipe internal surface and the gravity head. This paper describes an experimental investigation of the effect of gravity pressure head on the startup of a heat pipe under reflux mode. In this study, a heat pipe with internal axial grooves was placed in a vertical position with different tilt angles relative to the horizontal plane. Heat was applied to the evaporator at the bottom and cooling was provided to the condenser at the top. The liquid-flooded evaporator was divided into seven segments along the axial direction, and an electrical heater was attached to each evaporator segment. Heat was applied to individual heaters in various combinations and sequences. Other test variables included the condenser sink temperature and tilt angle. Test results show that as long as an individual evaporator segment was flooded with liquid initially, a superheat was required to vaporize the liquid in that segment. The amount of superheat required for liquid vaporization was a function of gravity pressure head imposed on that evaporator segment and the initial temperature of the heat pipe. The most efficient and effective way to start the heat pipe was to apply a heat load with a high heat flux to the lowest segment of the evaporator.

Description: The paper looks at the radiant heat exchange between some fairly primitive geometry components, and a few more complex, to understand the radiant energy distribution under a very common radiant lamp consisting of 6 quartz tube (tungsten element) heaters. This is looking at the basic physics of a common device used around the world for many decades. Other papers have looked at this same topic, but ours is looking at other topics we have not seen addressed in the literature (that explain why it is what it is, and other things affecting data interpretation).

Description: Numerical simulations and wind tunnel experiments were performed to investigate flow separation and its control over a wall-mounted hump model. Three-dimensional, unsteady fluid dynamic simulations were used to capture the relevant flow physics of unsteady flow separation and its control via active and passive flow control methods. Surface pressure measurements and surface oilflow visualization were obtained in the experiments. Current measurements documented a considerably thinner incoming boundary layer, but similar pressure distribution, compared to the reference data reported in the CFD (Computational Fluid Dynamics) Validation (CFDVAL 2004) Experiments. Consistent with the data available in the literature, numerical simulations predicted a longer separation bubble, which manifested itself as a shift in the pressure distributions. Streamwise vortices generated by passive vortex generators increased the suction pressure and provided substantial pressure recovery. Numerical simulations of vortex generators qualitatively predicted the effects of control, and revealed patterns of attached/separated flow regions. On the other hand, active flow control using steady discrete jets reduced, but was not able to eliminate, flow separation for the tested configuration. Although the major disagreement between the numerical and experimental results was in the pressure recovery region due to the inaccurate prediction of separation bubbles, the relative pressure recoveries from the baselines were comparable. Surface oilflow visualization and simulated surface streamlines were qualitatively in good agreement revealing the key flow features.

Description: Accurate calculation of thermal protection material response is critical to the vehicle design for missions to the Saturn moon Titan. In this study, Icarus, a three-dimensional, unstructured, finite-volume material response solver under active development at NASA Ames Research Center, is used to compute the in-depth material response of the Huygens spacecraft along its November 11 entry trajectory. The heatshield analyzed in this study consists of a five-layer stack-up of Phenolic Impregnated Carbon Ablator (PICA), aluminum honeycomb, adhesive, and face sheetmaterials. During planetary entry, the PICA outer layer is expected to undergo pyrolysis. A surface energy balance boundary condition that captures both time- and spatial-variance of surface properties during entry is used in the simulation.

Description: Understanding fluid behavior in microgravity environments is essential to further development of cryogenic storage in space environments. The Zero Boil Off Tank (ZBOT) experiment was designed to investigate two-phase pressurization and depressurization of a tank in a microgravity environment. The test fluid was the refrigerant Perfluoro-normal-Pentane (PNP). Thermal modeling for the ZBOT model was conducted using Thermal Desktop and SINDA/FLUINT. The temperature distribution within the fluid of the tank is of particular interest. This particular work is centered on ascertaining the thermal behavior of the refrigerant in order to build more complete models of fluid in microgravity. Separate cases were run modeling experiments that were conducted both on the ground and on the International Space Station (ISS) to compare 1g and microgravity environments. The microgravity modeling cases consisted of a fluid lump representing the vapor ullage suspended in a solid to represent the liquid. Mass flow between the liquid and vapor was modeled using the Schrage equation for mass flow. Initial results indicate that the pressure rise and temperature increase within the fluid closely align with the experimental data by matching initial conditions of the experiment. This work is ongoing and will yield further insights into the thermal behavior of fluid mixing in microgravity.

Description: The maturation of Cryogenic Fluid Management (CFM) Technologies is essential for achieving NASA's future long duration missions. Propulsion systems utilizing cryogens are necessary to achieve NASA's exploration missions to the moon, Mars, and beyond. Current State Of the Art (SOA) CFM technologies enable cryogenic propellants to be stored for several hours prior to their use. However, some envisioned mission architectures require that cryogens to be stored for two years or longer. The fundamental roles of CFM technologies are long term storage of cryogens, propellant tank pressure control and propellant delivery. In the presence of heat, the cryogens will "boil-off" over time resulting in excessive pressure buildup, off-nominal propellant conditions for engine consumption, and propellant loss. To achieve long term storage and tank pressure control, the CFM elements will intercept and/or remove any heat from the propulsion system. All functions are required to be performed both with and without the presence of a gravitational field. Which CFM technologies are required is a function of the cryogens used, mission architecture, vehicle design and propellant tank size. To enable NASA's crewed missions beyond Low Earth Orbit, a total of twenty-seven CFM technologies have been identified to support various In-Space Stages and Lander/Ascent Vehicles. A set of CFM Technology Development Roadmaps have been created identifying the current Technology Readiness Level (TRL) of each element, current technology "gaps", and existing technology development efforts. The roadmaps include a methodical approach and schedule to achieve a flight demonstration, hence maturing CFM technologies to TRL 6/7 for infusion into the NASA's exploration elements. Additionally, a survey of the aerospace industry was completed to understand their views on the various technologies and how they would be infused. This does not cover all possible technologies, but rather those that are of interest to NASA specifically.

Description: The Flow Boiling and Condensation Experiment (FBCE) is a flight experiment that is designed to operate in the Fluids Integrated Rack (FIR) on the International Space Station (ISS). The goal of the FBCE is to obtain heat transfer data, as well as general flow data, for two-phase flow systems in microgravity. This will help in the design of thermal management systems that are able to utilize latent heat transfer more efficiently.

Description: No abstract available

Description: NASA is currently working on developing its predictive modeling capabilities to support future missions that require long term storage of cryogenic propellants. Through the Evolvable Cryogenics project, Development and Validation of Analysis Tools (DVAT) task, both CFD and multi-node fluid modeling tools are being validated against to increase the following cryogenic fluid management technologies: Self-Pressurization, Pressure Control, Helium Pressurization, de-stratification, jet mixing, Tank and transfer line chill-down, tank filling and transfer. NASA is using previous and future micro-gravity experiments to validate both types of models. Recent activities include: Validation of the Tank Pressure Control Experiment (TPCE), Hydrogen and Helium pressurization, and Completion of the Zero Boil Off Tank (ZBOT) experiment on ISS. Future activities include validation of the ZBOT experiment with both CFD and multi-node analysis tools, validation of the Cryogenic Demonstration System of the Robotic Refueling Mission (RRM3).

Description: A thermal protection system (TPS) comprising a mixture of silicon carbide and SiOx that has been converted from Si that is present in a collection of diatom frustules and at least one diatom has quasi-periodic pore-to-pore separation distance d(p-p) in a selected range. Where a heat shield comprising the converted SiC/SiOx frustules receives radiation, associated with atmospheric (re)entry, a portion of this radiation is reflected so that radiation loading of the heat shield is reduced.

Description: Computational fluid dynamics (CFD) computations are performed at time increments using structural properties of the nozzle and flow properties of combustion products flowing through the nozzle. Each CFD computation accounts for movement of the wall geometry of the rocket nozzle due to the flowfield. Structural dynamics computations are performed at each time increment using the CFD computations in order to describe the movement of the wall geometry. Mesh dynamics computations at each time increment redefine the flowfield to account for the movement of the wall geometry. The mesh dynamics computations are based on a spring analogy process. The computations are iterated to solution convergence at each time increment with results being output to an output device.

Description: We present a high-order finite-element method for moving body and fluid/structure interaction problems. Our solution strategy is based on a space-time discontinuous Galerkin (DG) spectral-element discretization which extends to arbitrary order of accuracy. The space-time DG discretization is a natural choice for moving body and fluid-structure interaction problems as moving surfaces are incorporated simply by considering curved space-time elements whose space-time faces align with the moving body. We present a discontinuous-Galerkin in time discretization for six-degree of motion modeling of rigid bodies, and a continuous-Galerkin discretization for equations of linear elasticity to generate curved space-time meshes. Numerical results for several simple 2D test cases are presented in order to verify the implementation of the different models. Finally we present a preliminary dynamic simulation of a parachute.

Description: Lattice Boltzmann (LB) and hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's Revolutionary Computational Aerosciences (RCA) standard test cases for separated flows. A detailed comparison between the performance and accuracy of the two emerging numerical methodologies for turbulence resolving simulations, i.e. the LB and hybrid RANS/LES methods will be presented. This contribution addresses the RCA technical challenge to identify and down-select critical turbulence, transition, and numerical method technologies for 40% reduction in predictive error for standard turbulence separated flow test cases. Results for the 2D NASA wall-mounted hump and the axisymmetric transonic bump including time-averaged pressure coefficient, skin friction, and velocity pro les, as well as resolved and modeled Reynolds stresses for both numerical approaches will be presented and differences between LB and hybrid RANS/LES will be discussed.

Description: The Hypersonic Materials Environmental Test System arc-jet facility located at the NASA Langley Research Center in Hampton, Virginia, is primarily used for the research, development, and evaluation of high-temperature thermal protection systems for hypersonic vehicles and reentry systems. In order to improve testing capabilities and knowledge of the test article environment, a detailed three-dimensional model of the arc-jet nozzle and free-jet portion of the flow field has been developed. The computational fluid dynamics model takes into account non-uniform inflow state profiles at the nozzle inlet as well as catalytic recombination efficiency effects at the probe surface. Results of the numerical simulations are compared to calibrated Pitot pressure and stagnation-point heat flux for three test conditions at low, medium, and high enthalpy. Comparing the results and test data indicates an effectively fully-catalytic copper surface on the heat flux probe of about 10% recombination efficiency and a 2-3 kPa pressure drop from the total pressure measured at the plenum section, prior to the nozzle. With these assumptions, the predictions are within the uncertainty of the stagnation pressure and heat flux measurements. The predicted velocity conditions at the nozzle exit were also compared and showed good agreement with radial and axial velocimetry data.

Description: After the Columbus Moderate Temperature Loop (MTL) InterFace Heat eXchanger (IFHX) low temperature event of GMT 345-2013, NASA investigated relevant transient scenarios involving IFHX rupture after water freezing and subsequent thawing. NASA recommended development of a Fault Detection Isolation and Recovery (FDIR) plan that would, in the event of a heat exchanger freeze event, close the Water On/Off Valves (WOOVs) to isolate the heat exchanger and prevent ammonia from the external flow loops from spreading into the cabin. NASA performed a preliminary simplified analysis for the reference case of IFHX rupture, but for a deeper understanding TAS developed detailed SINDA-FLUINT models of the Columbus ITCS that were built and run through the SINAPS GUI. This allowed simulation of the ammonia leakage physics including the variation of environmental parameters, thus providing more accurate and specific input to the FDIR under development. The result was finalization of the IFHX WOOVs closure sequence and wait times to contain the ammonia propagation to Columbus and allow identification of the leaking IFHX. In addition, the analysis results provided reference pressure profiles to be used on console and by the Engineering as support for the telemetry data assessment in case of failure.This paper gives an overview on the issue and focuses on the analytical aspects of the multiphase fluid dynamics involved.

Description: Disclosed herein is a cryogenic heat transfer system capable of transferring 50 W or more at cryogenic temperatures of 100.degree. K or less for use with cryocooler systems. In an embodiment, a cryogenic heat transfer system comprises a refrigerant contained within an inner chamber bound by a condenser in fluid communication with an evaporator through at least one flexible conduit, the condenser in thermal communication with the cold station of a cryocooler, and the evaporator positionable in thermal communication with a heat source, typically a radiation shield of a cryogenic chamber. A process to remove heat from a cryogenic chamber is also disclosed.

Description: Several quantitative measurements extracted from nitric oxide (NO) planar laser-induced fluorescence (PLIF) data obtained in a hypersonic boundary layer are reported: (a) off-body NO mole fraction; (b) surface heat flux; and (c) near-wall static temperature. The experimental data was obtained at NASA Langley Research Centers 31 in. Mach 10 air tunnel. NO was seeded into the flow through a spanwise slot on the surface of the 10 degree half-angle wedge model. An ultraviolet planar laser sheet was positioned perpendicular to the wedge surface, downstream of the seeding slot, to excite six fluorescence transitions. A method for extracting the relative NO mole fraction, based on spatial variations of the J= 0.5 PLIF signal, is presented. Combined with the principle of mass conservation, the absolute NO mole fraction is determined. These measurements were used to assess CFD diffusion modelling, correct previously reported PLIF thermometry results, and develop methods for NO-PLIF heat transfer measurements.

Description: The development and implementation of kL-based Reynolds Average Navier-Stokes (RANS) two-equation turbulence models are reported herein. The kL is based on Abdol-Hamid's closure and Menter's modification to Rotta's two-equation model. Rotta shows that a reliable transport equation can be formed from the turbulent length scale L, and the turbulent kinetic energy k. Rotta's kL equation is well suited for term-by-term modeling and displays useful features compared to other scale formulation. One of the important differences is the inclusion of higher order velocity derivatives in the source terms of the scale equation. This can enhance the ability of RANS solvers to simulate unsteady flows in URANS mode. The present report documents the formulation of two model levels of turbulence models as implemented in the computational fluid dynamics FUN3D code. The levels are the two-equation linear k-kL and the two-equation algebraic Reynolds stress model (ARSM). Free shear, separated and corner flow cases are documented and compared with experimental, and other turbulence model data. The results show generally very good comparisons with experimental data. The results from this formulation are similar or better than results using the SST two-equation turbulence model. ARSM shows great promise with similar level of computational resources as basic two-equation turbulence models.

Description: The near and very near wake of thin flat plates with both sharp and circular trailing edges (TEs) are investigated with direct numerical simulations (DNSs). The TE is circular in two of the cases (IN & NS) and sharp in one of them (ST). The separating boundary layers are turbulent in all cases. The objectives of this study are twofold. The first is to explore the effect of significantly reducing Re(sub D) (Reynolds number based on circular TE diameter, D) on the flow in the TE region, and the shedding process (Cases IN and NS). The second is to better understand the reasons underlying the findings of an earlier experimental wake investigation (sharp TE) where (1) the center-line values in normal intensity, and the peak in shear stress profiles in the cross-stream direction, were found to first increase in the streamwise direction (x), from that obtained at the TE, before diminishing further downstream, and (2) a broadband peak was observed in centerline cross-stream velocity (v) spectra (indicating quasi-periodicity, possibly due to vortices or wave-like motions). Case ST from the present study showed a near wake instability resulting in spanwise vortices (with a streamwise component). The instability is intermittent and contributes to both the broadband peak in the v spectrum and the initial increases in normal intensity and shear stress (as in the experiment). Case NS, with the lower value of ReD is an "essentially" non-shedding case where the flow in the TE region continually changes direction (upward/downward) because of turbulence. Case IN, with twice the value of ReD as Case NS, also exhibits a swaying motion in the TE region. In addition, vortex shedding is initiated during periods when the flow direction changes rapidly. Shedding in this case is intermittent. It results in a peak in the v spectrum obtained at the centerline (x/D = 1.0).

Description: In the context of Large- Eddy Simulations (LES), Boundary-layer inflow turbulence is simulated using both the Synthetic Eddy Model (SEM) and Digital Filtering (DF). The effects of the projection error are investigated. The effect of the prescribed length scales on the adjustment region was found to be negligible for length scales less than one-tenth of the boundary-layer thickness. While it was conjectured that one method of the two might be more robust than the other, our results show that both the Digital Filtering Method and the Synthetic Eddy Method accurately replicate the boundary layer while successfully accounting for inflow turbulence.

Description: Experiments were performed in NASAs SW-2 cascade facility to compare three trailing edge actuation concepts to a 3D airfoil section with no trailing edge treatment. At a Reynolds number of 105, trailing edge pulsed ejection using fluidic oscillator devices was shown to fill the momentum deficit in the wake more uniformly than other actuators tested, with expected benefits for tonal noise in engine fans. Furthermore, pulsed ejection was found to alter the acoustic signature of the wake to reduce broadband noise. In some locations in the wake, spectral components of velocity were found to be reduced by 2 to 5 dB across nearly all frequencies. Trailing edge pulsed ejection is established as a feasible concept to reduce both tonal and broadband noise emissions from aircraft engines.

Description: The development and implementation of kL-based Reynolds Average Navier-Stokes (RANS) turbulence models are reported herein. The kL is based on Abdol-Hamid's closure and Menter's modi cation to Rotta's two-equation model. Rotta shows that a reliable transport equation can be formed from the turbulent length scale L, and the turbulent kinetic energy k. Rotta's kL equation is well suited for term-by-term modeling and displays useful features compared to other scale formulation. One of the important di erences is the inclusion of higher order velocity derivatives in the source terms of the scale equation. This can enhance the ability of RANS solvers to simulate unsteady ows in URANS mode. The present report documents the formulation of three model levels of turbulence models as implemented in the CFD code FUN3D. Methodology and calibration examples are shown in detail. The levels are the linear k-kL and the two-equation algebraic Reynolds stress model (ARSM) as well as the full Reynolds Stress Model (RSM). Attached, separated and corner ow cases are documented and compared with experimental, theoretical and other turbulence model data. The results show generally very good comparisons with canonical and experimental data. The results from this formulation are similar or better than results using the SST two- equation turbulence model. ARSM shows great promise with similar level of computational resources as general two equation turbulence models.

Description: No abstract available

Description: Lattice Boltzmann (LB) based Large Eddy Simulation (LES), Reynolds-averaged Navier-Stokes (RANS) as well as hybrid RANS/LES methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's wall-mounted hump. Computational results are compared with experiments performed by Greenblatt et al. A detailed comparison between the accuracy and resolution requirements of the two approaches for turbulence resolving simulations, as well as the suitability of different grid paradigms (body-fitted curvilinear and block structured Cartesian) are presented. This test case is part of NASA's Revolutionary Computational Aerosciences (RCA) sub-project which addresses the technical challenge of predicting flow separation and reattachment accurately. Improvements in predictive accuracy by as much as 90% are demonstrated using LB as well as hybrid RANS/LES approaches compared to state-of-the-art steady state RANS simulations.

Description: Electrowetting heat pipes (EHPs) are a newly conceptualized class of heat pipes, wherein the adiabatic wick section is replaced by electrowetting-based pumping of the condensate (as droplets) to the evaporator. Specific advantages include the ability to transport high heat loads over long distances, low thermal resistance and power consumption, and the absence of moving mechanical parts. In this work, we describe characterization of key microfluidic operations (droplet motion and splitting) underlying the EHP on the International Space Station (ISS). The testing was performed under the Advanced Passive Thermal eXperiment (APTx) project, a project to test a suite of passive thermal control devices funded by the ISS Technology Demonstration Office at NASA JSC (Johnson Space Center). A rapid manufacturing method was used to fabricate the electrowetting device on a printed circuit board. Key device-related considerations were to ensure reliability and package the experimental hardware within a confined space. Onboard the ISS, experiments were conducted to study electrowetting-based droplet motion and droplet splitting, by imaging droplet manipulation operations via pre-programmed electrical actuation sequences. An applied electric field of 36 Volts per micron resulted in droplet speeds approaching 10 millimeters per second. Droplet splitting dynamics were observed and the time required to split droplets was quantified. Droplet motion data was analyzed to estimate the contact line friction coefficient. Overall, this demonstration is the first-ever electrowetting experiment in space. The obtained results are useful for future design of the EHP and other electrowetting-based systems for microgravity applications.

Description: Introduction: NASAs next mission to Mars, the Mars 2020, will use the same heatshield of the Mars Science Laboratory (MSL) for thermal protection during entry, descent and landing. The heatshield is a tiled system made of Phenolic Impregnated Carbon Ablators (PICA) blocks [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers excellent performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of atmospheric entry and material response. MEDLI recorded, among others, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to compare the thermal response of the MSL heatshield to the MISP flight data. In preparation to Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against MEDLI flight data.

Description: Protecting a spacecraft during atmospheric entry is one of highest risk factors that needs to be mitigated during design of a space exploration mission. At entry speeds from space, air turns into high-temperature plasma, and spacecraft Thermal Protection Systems (TPS) are needed to protect the vehicle payload. Modern successful material architectures of spacecraft shields use a porous carbon fiber substrate impregnated with phenolic as an ablator material. In the lecture, efforts to build a Predictive Material Modeling framework for porous ablators from micro-scale to macro-scale will be presented. Several numerical methods and techniques will be summarized that use voxelized images to compute geometrical properties of the porous substrate. These computed properties include porosity, specific surface area and tortuosity that are otherwise indirectly measured through experimental techniques. Direct simulation Monte Carlo (DSMC), a particle-based method for approximating the Boltzmann equation, is used to compute the permeability coefficient of the porous substrate based on its digitized representation. The method computes the flow within the microstructure, where the size of the pores may approach the mean-free-path of the flow. Finally, a high-fidelity model implemented in PATO (Porous-material Analysis Toolbox) is discussed, and some examples of ablative material response are presented, including for the first time 3D simulations of the full tiled heat shield for the Mars Science Laboratory (MSL) capsule.

Description: No abstract available

Description: Recent introduction of Coaxial Thermocouple type calorimeters into the NASA Ames arc jet facilities has inspired an analysis of 2D conduction effects internal to this type of calorimeter. The 1D finite slab inverse analysis (which is typically used to deduce the heat transfer to the calorimeter) relies on the assumption that lateral conduction (i.e., 2D effects) is negligible. Most calorimeter bodies have a spherical nose, which in itself is a violation of the 1D finite slab analysis assumption. Secondly most calorimeters experience a variation in heating across the face of the body which is also a violation of the 1D finite slab analysis assumption. It turns out that these two effects tend to cancel each other to some extent. This paper shows the extent to which error exists in the analysis of the Coaxial Thermocouple type calorimeters, and also offers analysis strategies for reducing the errors.

Description: Due to the unique thermal vacuum testing requirements for a Mars Rover instrument, NASA Goddard developed a low cost, high fidelity thermal control system utilizing Thermal Electric Coolers (TECs) combined with a heat rejection fluid loop to actively control 8 independent payload thermal boundary zones in a simulated Mars pressure vacuum chamber with a Carbon Dioxide atmosphere. These zones could control instrument components to a specific temperature as a function of time to simulate exact temporal flight boundary predictions.The Mars Organic Molecule Analyzer (MOMA) instrument is a dual source (pyrolysis gas chromatograph and laser desorption) mass spectrometer (MS) based package that detects and characterizes organic molecules, as part of ESA's 2020 ExoMars Rover mission to seek the signs of life on Mars.Due to the unique thermal vacuum testing requirements for a Mars Rover instrument, NASA Goddard developed a low cost, high fidelity thermal control system utilizing Thermal Electric Coolers (TECs) combined with a heat rejection fluid loop to actively control 8 independent payload thermal boundary zones in a simulated Mars pressure vacuum chamber with a Carbon Dioxide atmosphere. These zones could control instrument components to a specific temperature as a function of time to simulate exact temporal flight boundary predictions.The Mars Organic Molecule Analyzer (MOMA) instrument is a dual source (pyrolysis gas chromatograph and laser desorption) mass spectrometer (MS) based package that detects and characterizes organic molecules, as part of ESA's 2020 ExoMars Rover mission to seek the signs of life on Mars.

Description: We present key features of the CGNS standard, focusing on its two main elements, the data model (CGNS/SIDS) and its implementations (CGNS/HDF5 and CGNS/Python). The data model is detailed to emphasize how the topological user oriented information, such as families, are separated from the actual meshing that could be split or modified during the CFD work flow, and how this topological information is traced during the meshing process. We also explain why the same information can be described in multiple ways and how to handle such alternatives in an application. Two implementations, using HDF5 and Python, are illustrated in several use examples, both for archival and interoperability purposes. The CPEX extension formalized process is explained to show how to add new features to the standard in a consensual way; we present some of the next extensions to come. Finally we conclude by showing how powerful a consensual public approach like CGNS can be, as opposed to a stand-alone private one. All throughout the paper, we demonstrate how the use of CGNS could be of great benefit for both the meshing and CFD solver communities.

Description: Performance tests of non-contacting finger seal designs were conducted at 300, 700, 922 K (70, 800 and 1200 F) at pressure differentials up to 517 kPa (75 psid) and surface speeds up to 366 m/s (1200 ft/s). Room temperature, static analysis of the seal was performed. A simplified CFD model was developed to examine pressure loads within the seal. Results from the CFD model were used as input to a finite element analysis model of a six-finger segment of the non-contacting finger seal. Examination of predicted deflections of individual components of the seal gives insight into the seal behavior. Wear patterns from testing verify the pattern of radial deflection. The models are used to predict maximum pressure differential capability of the seal and compared to experimental results. The CFD model slightly under-predicts the measured leakage flow factor, but has the same trend as the measured flow factor versus pressure differential.

Description: Electrically Driven Thermal Management is an active research and technology development initiative incorporating ISS technology flight demonstrations (STP-H5), development of Microgravity Science Glovebox (MSG) flight experiment, and laboratory-based investigations of electrically based thermal management techniques. The program targets integrated thermal management for future generations of RF electronics and power electronic devices. This presentation reviews four program elements: i.) results from the Electrohydrodynamic (EHD) Long Term Flight Demonstration launched in February 2017 ii.) development of the Electrically Driven Liquid Film Boiling Experiment iii.) two University based research efforts iv.) development of Oscillating Heat Pipe evaluation at Goddard Space Flight Center.

Description: It is known that ice nucleating particles (INP) immersed within supercooled droplets promote the formation of ice. Common theoretical models used to represent this process assume that the immersed particle lowers the work of ice nucleation without significantly affecting the dynamics of water in the vicinity of the particle. This is contrary to evidence showing that immersed surfaces significantly affect the viscosity and diffusivity of vicinal water. To study how this may affect ice formation this work introduces a model linking the ice nucleation rate to the modification of the dynamics and thermodynamics of vicinal water by immersed particles. It is shown that INP that significantly reduce the work of ice nucleation also pose strong limitations to the growth of the nascent ice germs. This leads to the onset of a new ice nucleation regime, called spinodal ice nucleation, where the dynamics of ice germ growth instead of the ice germ size determines the nucleation rate. Nucleation in this regime is characterized by an enhanced sensitivity to particle area and cooling rate. Comparison of the predicted ice nucleation rate against experimental measurements for a diverse set of species relevant to cloud formation suggests that spinodal ice nucleation may be common in nature.

Description: High-fidelity Computational Fluid Dynamics (CFD) simulations have been carried out for several multi-rotor Unmanned Aerial Vehicles (UAVs). Three vehicles have been studied: the classic quadcopter DJI Phantom 3, an unconventional quadcopter specialized for forward flight, the SUI Endurance, and an innovative concept for Urban Air Mobility (UAM), the Elytron 4S UAV. The three-dimensional unsteady Navier-Stokes equations are solved on overset grids using high-order accurate schemes, dual-time stepping, and a hybrid turbulence model. The DJI Phantom 3 is simulated with different rotors and with both a simplified airframe and the real airframe including landing gear and a camera. The effects of weather are studied for the DJI Phantom 3 quadcopter in hover. The SUI En- durance original design is compared in forward flight to a new configuration conceived by the authors, the hybrid configuration, which gives a large improvement in forward thrust. The Elytron 4S UAV is simulated in helicopter mode and in airplane mode. Understanding the complex flows in multi-rotor vehicles will help design quieter, safer, and more efficient future drones and UAM vehicles.

Description: Experimental measurements were performed on a swept flat-plate model with an airfoil leading edge and imposed chordwise pressure gradient to determine the effects of a backward-facing step on transition in a low-speed stationary crossflow-dominated boundary layer. Detailed hot-wire measurements were performed for three step heights ranging from 36 to 49% of the boundary-layer thickness at the step and corresponding to subcritical, nearly critical, and critical cases. In general, the step had a small localized effect on the growth of the stationary crossflow vortex, whereas the unsteady disturbance amplitudes increased with increasing step height. Intermittent spikes in instantaneous velocity began to appear for the two larger step heights. A physical explanation was provided for the mechanism leading to transition and the sudden movement in the transition front due to the critical steps. The large localized velocity spikes, which ultimately led to an intermittent breakdown of the boundary layer, were the result of nonlinear interactions of the different types of unsteady instabilities with each other and with the stationary crossflow vortices. Thus, the unsteady disturbances played the most important role in transition, but the stationary crossflow vortices also had a significant role via the modulation and the increased amplitude of the unsteady disturbances.