ALBERT

Description: This paper presents the results of a series of total and spectral solar irradiance measurements made at ground surface (Table Mountain Facility, Calif., altitude 2.18 km). The spectral irradiance data are presented for the 0.3-3.0-micron spectral region for air mass 1.5.

Description: A proposal for a multi-institutional investigation of the processes involved in the growth and maintenance of high level extended clouds is presented. Mapping of variability of the cloud and of its radiative characteristics in terms of the meteorological environment of the cloud; performance of case studies involving observation of the cloud microphysics and radiation characteristics; and investigation of the processes responsible for the generation, maintenance, and dissipation of the cloud system are recommended. Both modeling and monitoring activities are considered. The specific research projects which the author proposes to carry out are described. Suggestions for the administrative organization of the total effort are presented.

Description: The interplay of the various physical processes involved in the formation, maintenance, and decay of middle and upper tropospheric stratiform clouds is discussed. Ice phase fair weather cloud forms are considered. Simulations of cirriform clouds which attempt to incorporate the physical processes in an interactive manner were performed. A two dimensional time dependent Eulerian numerical model, which incorporates all of the important physical processes in a simplified way, is employed to investigate the role of these processes in the evolution of a cloud in an isolated atmospheric layer. Physical parameters considered are the eddy viscosity and the thermal, water vapor, and ice water eddy diffusivities.

Description: A model that explains the flat-spot power loss phenomenon is presented. Evidence suggests that the effect is due to localized metallurgical interactions between the silicon substrate and the contact metallization. These reactions are shown to result in localized regions in which the P-N junction is destroyed and replaced with a metal semiconductor-like interface. The effects of thermal treatment, crystallographic orientation, junction depth, and metallization are shown along with a method of preventing the effect through the suppression of vacancy formation at the free surface of the contact metallization. Data indicating the effectiveness of a TiN diffusion barrier in preventing the effect are also given.

Description: Stratospheric limb radiance profiles versus altitude of closest approach of the line of sight to the Earth's surface have been measured before and after the Mount St. Helens eruptions by means of photographs taken from a Sun-oriented balloon gondola floating above 35 km altitude over France. Preliminary data were reported for flights in October 1979 and in May and June 1980. The radiance integrated along the line of sight as in-situ radiance (R) can be derived taking into account absorption by ozone and air. The onion peeling inversion method was used to derive the vertical radiance (R) profiles respectively. The values of R were determined in the solar azimuth. The solar elevation angles are chosen larger for the backscattering observation than for the forward scattering observation to deal with as similar illumination conditions as possible despite the Earth's sphericity.

Description: Microscopical investigation of volcanic ash collected from ground stations during Mount St. Helens eruptions reveal a distinctive bimodel size distribution with high concentrations of particle ranges at (1) 200-100 microns and (2) 20-0.1 microns. Close examination of individual particles shows that most larger ones are solidified magma particles of porous pumice with numerous gas bubbles in the interior and the smaller ones are all glassy fragments without any detectable gas bubbles. Elemental analysis demonstrates that the fine fragments all have a composition similar to that of the larger pumice particles. Laboratory experiments suggest that the formation of the fine fragments is by bursting of glassy bubbles from a partially solidified surface of a crystallizing molten magma particle. The production of gas bubbles is due to the release of absorbed gases in molten magma particles when solubility decreases during phase transition. Diffusion cloud chamber experiments strongly indicate that sub-micron volcanic fragments are highly hygroscopic and extremely active as cloud condensation nuclei. Ice crystals also are evidently formed on those fragments in a supercooled (-20 C) cloud chamber. It has been reported that charge generation from ocean volcanic eruptions is due to contact of molten lava with sea water. This seems to be insufficient to explain the observed rapid and intense lightning activities over Mount St. Helens eruptions. Therefore, a hypothesis is presented here that highly electrically charged fine solid fragments are ejected by bursting of gas bubbles from the surface of a crystallizing molten magma particles.

Description: The direct solar radiation transmission record at Mauna Loa, dating from 1958 to the present, revealed with remarkable precision the presence of stratospheric aerosol from volcanic activity. This record can be used to quantify the intensity of the stratospheric volcanic aerosol perturbation following a significant eruption in reference to the Agung event in 1963. The Mount St. Helens' stratospheric cloud was first detected by lidar at 18 km over Mauna Loa on 17 July. The atmospheric transmission was seen to decrease slightly after that time, but only a few tenths of 1 percent. Although it is still fairly early to draw a definite conclusion on the ultimate magnitude of the Mount St. Helens stratospheric aerosol from the Mauna Loa results, it can be stated that the stratospheric aerosol optical depth presently observed is comparable with that observed from Fuego which erupted in 1974. At Boulder, Colorado, the atmospheric debris from Mount St. Helens was observed by lidar on a number of occasions. Also, observations of the diffuse, total and direct transmission of solar radiation were made on June 3 and 4. The latter set of observations is useful for deriving information on the scattering properties of the volcanic cloud. The lidar and solar radiation data are presented and some of their special features are discussed.

Description: Samples of stratospheric aerosols collected with U-2 aircraft for several months following the first three major eruptions of Mount St. Helens were analyzed for ash and liquid acid content. Ash grain sizes and compositions vary depending on collection altitude, location within the drifting cloud, and days following their injection. s computers Size distributions of ash particles vary with altitude. Generally small particles are depleted more rapidly at low altitudes (12 km) than at higher altitudes (17-18 km). Although samples collected 1 day after the first eruption of May 18, 1980, were dry, flow marks on the aircraft indicated parts of the cloud contained heavy acid concentrations. Indeed, all other samples obtained within 1 to 4 days after later eruptions (May 25 and June 12, 1980) were covered with copious amounts of liquid acid. Proportions of liquid to ash varied considerably depending on sampling location and cloud age. Because the acid-coated ash globules were large, they rapidly fell from the stratosphere until, by late June 1980, only a residue of acid droplets remained. Size distributions and concentrations of these droplets varied considerably.

Description: The NASA large flexible solar array space shuttle flight experiment is described. The 32 x 4 m wing is deployed from the shuttle bay, and experiments in electrical output, multiple deployment, and structural dynamics are planned. Both 2 x 4 cm and 5.9 x 5.9 cm cell assemblies on the array blanket are evaluated. Safety/hazards provisions are described, including emergency jettison provisions. Ground testing and hardware fabrication are summarized.

Description: A development program to produce 5.9 x 5.9 cm space quality silicon solar cells with a cost goal of 30 $/W is described. Cell types investigated include wraparound dielectric, mechanical wraparound and conventional contact configurations with combinations of 2 or 10 ohm/cm resistivity, back surface reflectors and/or fields, and diffused or ion implanted junctions. A single step process to cut cell and cover glass simultaneously is being developed. Results for cell and array tests are given. Large solar arrays that might use cells of this type are discussed.

Description: Objectives and progress in both low concentration ratio (6 to 10) and high concentration ratio ( 100) array developments are summarized. Problems encountered include: thermal control, maldistribution of concentrated sunlight, current busing, and optical surface degradation. The potential advantages over planar arrays are an order of magnitude reduction in per unit cost of power plus increased immunity to radiation damage.

Description: Results associated with exact solution of the Einstein-Boltzmann and Einstein-Maxwell-Boltzmann equations are presented. The generalization of Ehler's killing vector approach for the distribution function to charged particles is considered.

Description: Current-voltage curves were calculated for each cell in a cascade structure using a solar cell diode equation and superposition. Terms for the light generated current, diffusion current, space charge recombination current and series and shunt resistance are included. Individual current voltage curves are added in series with ohmic resistance losses for the cell interconnects to obtain the cascade cell performance. Temperature was varied with concentration, using several models, and ranged from 55 C at one Sun to between 80 and 200 C at 100 Suns. A variety of series resistance and internal resistances were used. Coefficients of the diffusion and recombination terms are strongly temperature dependent. The study indicates that maximum efficiency (30%) occurs in the 50 to 100X Sun concentration range, provided series resistance is below 0.015 ohm-sq cm and cell temperature is 80 C at 100 Suns.

Description: Gallium and boron doped silicon solar cells, processed by ion implantation followed by either laser or furnace anneal were irradiated by 1 MeV electrons and their postirradiation recovery by thermal annealing was determined. During the postirradiation anneal, gallium doped cells prepared by both processes recovered more rapidly and exhibited none of the severe reverse annealing observed for similarly processed 2 ohm-cm boron doped cells. Ion implanted furnace annealed 0.1 ohm-cm boron doped cells exhibited the lowest post-irradiation annealing temperatures after irradiation. The drastically lowered recovery temperature is attributed to the reduced oxygen and carbon content of the 0.1 ohm-cm cells. Analysis based on defect properties and annealing kinetics indicates that further reduction in annealing temperature is attainable with further reduction in the silicon's carbon and/or divacancy content after irradiation.

Description: Nineteen stratospheric samples from the eruption plumes of Mount St. Helens were collected in five flight experiments. The plume samples were collected at various altitudes from 13.1 to 20.7 km by using the Ames cryogenic sampling system on board the NASA U-2 aircraft. The enriched, cryogenically collected samples were analyzed by chromatography. The concentrations of aerosols precursor gases (OCS, SO2, and CS2), CH3Cl, N2O, CF2Cl2, and CFCl3 were measured by gas chromatography. Large enhancement of the mixing ratio of SO2 and moderate enhancement of CS2 and OCS were found in the plume samples compared with similar measurement under pre-volcanic conditions. A fast decay rate of the SO2 mixing ratio in the plume was observed. Measurement of Cl(-), SO2(2-), and NO3(-) by ion chromatography was also carried out on water solutions prepared from the plume samples. The results obtained with this technique imply large mixing ratios of HCl, (NO + NO2 + HNO3), and SO2, in which these constituents are the respective sources of the anions. Measurement of the Rn222 concentration in the plume was made. Other stratospheric constituents in the plume samples, such as H2O, CO2, CH4, and CO, were also observed.

Description: Mount St. Helens erupted somewhat less than 0.5 cu km of magma (dense rock equivalent) on May 18, 1980. The May 18 event was usually violent. As much 35% of the volume of the airfall material fell outside of the 2.5 mm isopach, which encloses about 88,000 sq km. This extraordinary dispersive power was transmitted by an eruption column which reached heights of more than 20 km. There was a lateral blast (or surge) of unusually large dimensions associated with the onset of the eruption. The magma is dacitic in composition and had a low ( 500 ppm) sulfur content. Distal ashes contain much nonmagmatic (lithic) material, but smaller ( 50 microns m) particles are mostly finely divided magmatic dacite. The grain size distributions of the ash are multimodal, frequently with peaks at 90, 25, and 10 microns. The finer populations fell out faster than their terminal velocities as simple particles would suggest. It is inferred that large proportions of the fine ash fell out as composite particles. This condition greatly reduces the atmospheric burden of silicate particles. Some of the unusual aspects (violence, intense surges, multimodal grain size distributions, lithic content of the ashes) of the eruption may be due to its phreatomagmatic character. The hydrothermal system above the magma may have infiltrated the magma body at the onset of the eruption. An "overprint" of the geochemistry of this hydrothermal system on the geochemistry of the magmatic gas system is likely. One important feature is that reduced gas species may be much more abundant than in many eruptions. Another is that fine ash may form aggregates more readily.

Description: The goals of map/wind (winter in Northern Europe) are to better understand: (1) the interaction of planetary waves of tropospheric origin; (2) the temporal and spatial development of sudden stratospheric warmings; (3) the temporal and spatial development of mesospheric cooling events in conjunction with stratospheric warmings; (4) the vertical and horizontal transport of minor constituents; (5) the effects on the chemistry of neutral and charged species of the large temperature changes occurring during stratospheric warmings and mesospheric cooling; (6) sources of turbulent energy; (7) the temporal and spatial development of turbulent layers; and (8) the contributions of dynamical processes to the heating and cooling of the mesospheric and turbopause region.

Description: Three general areas of study were identified: stratospheric composition; mesospheric and lower ionospheric structure and composition; and middle atmospheric dynamics. The role of chemical reactions and spectroscope in the study of the middle atmosphere is discussed.

Description: Organizations in the United States which are interested in MAP participation were surveyed. Satellites, rockets, balloons, and ground support systems are listed with available experimentation.

Description: The plans for India's participation in the middle Atmosphere Program are outlined.

Description: The NASA Lewis Research Center in cooperation with the World Health Organization, U.S.A. I.D., the Pan American Health Organization and national government agencies in some developing countries sponsored the installation of twenty photovoltaic powered medical vaccine storage refrigerator-freezer (R/F) systems. The Solar Power Corporation was selected as the contractor to perform the design, development and installation of these twenty units. Solar Power's experiences are described herein.

Description: The U.S. Coast Guard has developed a qualification test to screen photovoltaic modules for utilization on marine aids to navigation. The test is based on a combined-environment of hot and cold saltwater immersion and air pressurization. The test has demonstrated a very high acceleration factor and excellent correlation of electrical failures with modules in a concurrent real-time marine exposure.

Description: Design principles suggested here aim toward high conversion efficiency (greater than 15 percent) in polysilicon cells. The principles seek to decrease the liabilities of both intragranular and grain-boundary-surface defects. The advantages of a phosphorus atom concentration gradient in a thin (less than 50 microns) base of a p(+)/n(x)/n(+) drift-field solar cell, which produces favorable gradients in chemical potential, minority-carrier mobility and diffusivity, and recombination lifetime (via phosphorus gettering) are suggested. The degrading effects of grain boundaries are reduced by these three gradients and by substituting atoms (P, H, F or Li) for vacancies on the grain-boundary surface. From recent experiments comes support for the benefits of P diffusion down grain boundaries and, for quasi-grain-boundary-free and related structures. New analytic solutions for the n(x)-base include the effect of a power-law dependence between P concentration and lifetime. These provide an upper-bound estimate on the open circuit voltage. Finite-difference numerical solutions of the six Shockley equations furnish complete information about all solar-cell parameters and add insight concerning design.

Description: Major advances in photovoltaic (PV) Power Conditioning (PC) with respect to performance and low-cost potential have been made. Solutions have been obtained to interface and control problems related to adapting available inverter designs to the grid-connected, residential photovoltaic experiments. A description is presented to contributing research and development activities. Attention is given to aspects of residential systems experience, conceptual design studies, questions of optimum topology development, and promising advanced designs for residential PV provided by development efforts of the private sector.

Description: Mechanical fatigue of solar cell interconnects is a major failure mechanism in photovoltaic arrays. A comprehensive approach to the reliability design of interconnects, together with extensive design data for the fatigue properties of copper interconnects, has been published. This paper extends the previous work, developing failure prediction (fatigue) data for additional interconnect material choices, including aluminum and a variety of copper-Invar and copper-steel claddings. An improved global fatigue function is used to model the probability-of-failure statistics of each material as a function of level and number of cycles of applied strain. Life-cycle economic analyses are used to evaluate the relative merits of each material choce. The copper-Invar clad composites demonstrate superior performance over pure copper. Aluminum results are disappointing.

Description: Computer analysis indicates that a substantial increase in solar cell conversion efficiencies can be achieved by using two-cell, multi-bandgap tandem structures instead of single-junction cells. Practical AM1 efficiencies of about 30 percent at one sun and over 30 percent at multiple suns are to be expected. The further increases in efficiency calculated for a three-cell tandem structure are much smaller and may not justify the added complexity. For inexpensive two-cell tandem modules, Si is preferred for the bottom cell, and the top-cell material should have a bandgap of 1.75 to 1.80 eV. The GaAs-AlAs and GaAs-GaP systems are very attractive candidates for the top cell. Significant advances have been achieved in growing GaAs on Ge-coated Si substrates (for the two-terminal, two-cell structure) and in growing free-standing ultrathin GaAs layers (for the two-terminal or four-terminal structures). These advances should be transferable to the GaAs-AlAs and GaAs-GaP systems.

Description: The electric output of flat-plate photovoltaic arrays changes constantly, due primarily to changes in cell temperature and irradiance level. As a result, array loads such as direct-current to alternating-current power conditioners must be able to accommodate widely varying input levels, while maintaining operation at or near the array maximum power point.The results of an extensive computer simulation study that was used to define the parameters necessary for the systematic design of array/power-conditioner interfaces are presented as normalized ratios of power-conditioner parameters to array parameters, to make the results universally applicable to a wide variety of system sizes, sites, and operating modes. The advantages of maximum power tracking and a technique for computing average annual power-conditioner efficiency are discussed.

Description: The initial mass of the Crab Nebula's progenitor star is estimated by comparing the observed nebular chemical abundances with detailed evolutionary calculations for 2.4- and 2.6-solar-mass helium cores of stars with masses of 8 to 10 solar masses. The results indicate that the mass of the Crab's progenitor was between the upper limit of about 8 solar masses for carbon deflagration and the lower limit of about 9.5 solar masses set by the dredge-up of the helium layer before the development of the helium-burning convective region. A scenario is outlined for the evolution of the progenitor star. It is suggested that the Crab Nebula was probably the product of an electron-capture supernova.

Description: It is suggested that gravitationally bound astronomical systems ranging from asteroids to galaxy superclusters may derive their rotation from a hierarchy of cosmic turbulence, thus explaining the empirical specific angular momentum-mass relationship (j approximately equal to M to the 3/4 power) exhibited by these systems. It is shown that many of the properties of these systems, e.g., the random orientation of their spin vectors, can be accounted for if astronomical objects form in a turbulent environment.

Description: (Previously announced in STAR as N82-20197)

Description: (Previously cited in issue 12, p. 2037, Accession no. A81-29543)

Description: Several hundred topside ionograms were used to study simulated wave-particle interactions in the ionosphere. The study combined the benefits of high-frequency-resolution Alouette 2 analog sounder data with advanced digital graphics techniques. The study shows that the sounder phase can cause significant plasma heating when the plasma parameter is confined to specific ranges. The observations support the Harris instability generation process and the nonlinear Landau damping maintaining process for long-duration diffuse resonances. The observations also suggest that the so-called Q resonances have characteristics which imply that generation processes in a sounder-stimulated plasma turbulence may be involved.

Description: Commercially available metallurgical grade (MG) silicon has high B and P content which is not reduced significantly by directional solidification. By choosing high purity raw materials for an experimental Submerged Electrode Arc Furnace, most of the impurities are reduced to 10 ppmw. Directional solidification of upgraded metallurgical grade (UMG) silicon by the Heat Exchanger Method (HEM) has produced 16 cm x 16 cm cross section ingots with nearly single crystal structure. The main problem encountered during directional solidification was SiC impurities dispersed through the structure. Solar cells fabricated from UMG silicon that was directionally solidified twice by HEM have shown up to 12.33% (am1) conversion efficiency.

Description: A main source of high carbon levels in silicon crystals grown from melt under reduced pressures and contained in silica crucibles supported by graphite retainer/susceptor was identified by thermodynamic analysis. The calculations were verified by experimental results and the carbon level is reduced by approximately 50% with the use of molybdenum retainers.

Description: The most developed process for silicon crystal growth is the Czochralski (CZ) method which was in production for over two decades. In an effort to reduce cost of single crystal silicon for photovoltaic applications, a directional solidification technique, Heat Exchanger Method (HEM), was adapted. Materials used in HEM and CZ furnaces are quite similar (heaters, crucibles, insulation, etc.). To eliminate the cost of high purity argon, it was intended to use vacuum operation in HEM. Two of the major problems encountered in vacuum processing of silicon are crucible decomposition and silicon carbide formation in the melt.

Description: The Fixed Abrasive Slicing Techniques (FAST) is a new slicing technique that was developed to slice ingots more effectively. It was demonstrated that 25 wafers/cm can be sliced from 10cm diameter and 19 wafers/cm from 15 cm diameter ingots. Over 99% yield (222 out of a possible 224) was demonstrated during slicing of a 10 cm diameter ingots at 25 wafers/cm. The average thickness of wafers was 0.249 mm and the kerf was 0.151 mm. Slicing rates as high as 0.14 mm/min were also demonstrated for 10 cm diameter ingots.

Description: One of the major cost factors in silicon ingot technology adaptation for terrestrial photovoltaic application is in slicing boules into wafers. The most developed industrial practice is the Internal Diameter (ID) slicing. This method utilizes diamond cutting. The diamond stands up for long periods, hence, the cost of expendable materials is low. However, the ID technology as practiced today has poor material utilization. The Multiblade Slurry (MBS) method has low equipment and labor costs but its expendable material costs are high. Recently Multiwire Slurry (MWS) technology has shown very good material utilization, but its expendable material costs are even higher than MBS. The multiwire Fixed Abrasive Slicing Technique (FAST) still in advanced development stage, combines the low expendable material costs of ID method, the low labor and equipment costs of MBS and high material utilization of MWS.

Description: Directional solidification by the Heat Exchanger Method (HEM) is a viable approach for directional solidification of silicon ingots used for terrestrial solar cell applications. Some of the significant advances made during this phase of the program were: ingot size, 34 cm x 34 cm x 17 cm - 45 kg, usable material yield - 90%, solar cell efficiency averaged over the whole ingot - 85% of control CZ (35 kg ingot), very uniform resistivity over the boule, and cycle time for 36 kg ingots - 56 hours. Some of the problems encountered were growth rate decrease with increased ingot height, silicon carbide precipitates, and high dislocation density in HEM material. The silicon carbide is attributed to backstreaming of oil vapors from the vacuum pump; the high dislocation density is associated with the thermal history of the boule.

Description: Preliminary calculations employing statistical equilibrium techniques were carried out to determine brightness temperatures of water transitions occurring in the submillimeter band. The interesting candidates appear to be the 325 GHz, 380 GHz, and 448 GHz transitions, they are compared with the 183 GHz and 380 GHz transitions observed in the Orion Kleinmann-Low nebula and the combined results seem to be consistent with H2 densities of 100,000 -1 million cm-3 and a water column density of approximately 10 to 18th power. This implies a relative abundance of approximately 0.00001 which means that water may be about one twentieth of CO. In addition, it was found that for the conditions of the Orion plateau source, the 448 GHz line is expected to be a mild maser.

Description: Some developments in radiative transfer for magnetized neutron star conditions, and their application in models of the structure and properties of self-consistent polar cap emission regions are reviewed. Several of the assumptions and uncertainties involved are discussed, and present problems are indicated.

Description: The economic advantages of solar dish collectors are evaluated and compared with other energy systems. Labor, inflation and energy deregulation are considered.

Description: Solar energy systems were investigated which complement nuclear and coal technologies as a means of reducing the U.S. dependence on imported petroleum. Solar Thermal Energy Systems (STES) represents an important category of solar energy technologies. STES can be utilized in a broad range of applications servicing a variety of economic sectors, and they can be deployed in both near-term and long-term markets. The net present value of the energy cost savings attributable to electric utility and IPH applications of STES were estimated for a variety of future energy cost scenarios and levels of R&D success. This analysis indicated that the expected net benefits of developing an STES option are significantly greater than the expected costs of completing the required R&D. In addition, transportable fuels and chemical feedstocks represent a substantial future potential market for STES. Due to the basic nature of this R&D activity, however, it is currently impossible to estimate the value of STES in these markets. Despite this fact, private investment in STES R&D is not anticipated due to the high level of uncertainty characterizing the expected payoffs.

Description: The integration and check-out of a complete Dish Solar Stirling Thermal Power System is described. The preliminary results of the tests conducted thus far are presented. The results are very encouraging and show promise of high performance and efficiency. The outstanding performance and durability of the 4-95 Stirling engine was the highlight of this 6 month integration and test activity. Exposure to severe heat, dust, sand and wind during the summer months and heavy rains, high winds, including sand storms and freezing cold in recent months did affected the engine or the receiver in any noticable manner.

Description: The Jay Carter Enterprises (JCE) Paratransit Vehicle steam engine was tested over a range of conditions which might be experienced by the power converter subsystem of the Small Community Solar Thermal Power Experiment. Some difficulties were encountered getting the engine ready for testing. These difficulties were related to the five year dormancy of the entire system and to incomplete development work that had been going on at the time of cessation of steam engine work at JCE. Other difficulties were related to the fact that the particular expander being tested never ran before and possessed some manufacturing defects. Nevertheless, the engine was operated successfully and results of testing do verify results of computer simulations of the engine in regard to the effect of temperature and power level variations. Engine efficiency was good but generally lower than expected and performance dropped as testing continued. The effect of change in expansion ratio was not demonstrated because of deterioration in engine performance. Post-test inspection revealed numerous correctable defects.

Description: A study was performed by AiResearch Manufacturing Company, a division of The Garrett Corporation, on the development a high-temperature ceramic heat exchanger element to be integrated into a solar receiver producing heated air. A number of conceptual designs were developed for heat exchanger elements of differing configuration. These were evaluated with respect to thermal performance, pressure drop, structural integrity, and fabricability. The final design selection identified a finned ceramic shell as the most favorable concept. The shell is surrounded by a larger metallic shell. The flanges of the two shells are sealed to provide a leak-tight pressure vessel. The ceramic shell is to be fabricated by an innovative combination of slip casting the receiver walls and precision casting the heat transfer finned plates. The fins are bonded to the shell during firing. The unit is sized to produce 2150 F ar at 2.7 atm pressure, with a pressure drop of about 2 percent of the inlet pressure. This size is compatible with a solar collector providing a receiver input of 85 kw(th). Fabrication of a one-half scale demonstrator ceramic receiver has been completed.

Description: The modifications and testing of a standard Stirling engine, required for connection to a 25 kW induction alternator, for use with a solar thermal parabolic dish electric module is described. Power was absorbed by a GE induction alternator connected to the utility grid. Also included are the results from recent testing of another solar engine at the DOE-Georgia Tech solar site. It was done in parallel with the testing at Edwards for the purpose of comparing performance of two solar-only receivers, which were based on the standard 4-95 involute heat exchanger.

Description: Verification testing of a solar collector was undertaken prior to its operation as part of an industrial process heat plant at Capitol Concrete Products in Topeka, Kansas. Testing was performed at a control plant installed at Sandia National Laboratory, Albuquerque, New Mexico (SNLA). Early results show that plant performance is even better than anticipated and far in excess of test criteria. Overall plant efficiencies of 65 to 80 percent were typical during hours of good insolation. A number of flaws and imperfections were detected during operability testing, the most important being a problem in elevation drive alignment due to a manufacturing error. All problems were corrected as they occurred and the plant, with over 40 hours of operation, is currently continuing operability testing in a wholly-automatic mode.

Description: The development and preliminary test results for an air-cooled, hermetically sealed 20 kW sub E organic Rankine cycle engine/alternator unit for use with point focussing distributed receiver solar thermal power system. A 750 F toluene is the working fluid and the system features a high speed, single-stage axial flow turbine direct-coupled to a permanent magnet alternator. Good performance was achieved with the unit in preliminary tests.

Description: The development of a point-focus Fresnel lens solar concentrator for high-temperature solar thermal energy system applications is discussed. The concentrator utilizes a transmittance-optimized, short-focal-length, dome-shaped refractive Fresnel lens as the optical element. This concentrator combines both good optical performance and a large tolerance for manufacturing, deflection, and tracking errors. The conceptual design of an 11-meter diameter concentrator which should provide an overall collector efficiency of about 70% at an 815 C (1500 F) receiver operating temperature and a 1500X geometric concentration ratio (lens aperture area/receiver aperture area) was completed. Results of optical and thermal analyses of the collector, a discussion of manufacturing methods for making the large lens, and an update on the current status and future plans of the development program are included.

Description: Estimates are made showing that, as a consequence of rocket activity in the earth's upper atmosphere in the Shuttle era, average ice nuclei concentrations in the upper atmosphere could increase by a factor of two, and that an aluminum dust layer weighing up to 1000 tons might eventually form in the lower atmosphere. The concentrations of Space Shuttle ice nuclei (SSIN) in the upper troposphere and lower stratosphere were estimated by taking into account the composition of the particles, the extent of surface poisoning, and the size of the particles. Calculated stratospheric size distributions at 20 km with Space Shuttle particulate injection, calculated SSIN concentrations at 10 and 20 km altitude corresponding to different water vapor/ice supersaturations, and predicted SSIN concentrations in the lower stratosphere and upper troposphere are shown.

Description: (Previously announced in STAR as N82-22137)

Description: An analysis is performed on the J(k) = 12(k)-11(k) and 13(k)-12(k) transitions of methyl cyanide detected by other investigators in the direction of OMC-1. The original interpretation of those observations argues for the presence of two distinct temperature regions or possibly a temperature gradient within the cloud. The analysis presented here demonstrates that the observations of these particular molecular transitions are consistent with a single methyl cyanide emission region with a source kinetic temperature of 121.2 + or - 8.2 K and a molecular rotational temperature of 16.6 + or - 1.8 K.

Description: The diffuse 2-60 keV X-ray background has a galactic component clearly detectable by its strong variation with both galactic latitude and longitude. This galactic component is typically 10 percent of the extragalactic background toward the galactic center, half that strong toward the anticenter, and extrapolated to a few percent of the extragalactic background toward the galactic poles. It is acceptably modeled by a finite radius emission disk with a scale height of several kiloparsecs. The averaged galactic spectrum is best fitted by a thermal spectrum of kT about 9 keV, a spectrum much softer than the about 40 keV spectrum of the extragalactic component. The most likely source of this emission is low luminosity stars with large scale heights such as subdwarfs. Inverse Compton emission from GeV electrons on the microwave background contributes only a fraction of the galactic component unless the local cosmic ray electron spectrum and intensity are atypical.

Description: The influence of the geographical distribution and the number of the surface stations in the ozone detecting network on changes in global ozone inferred from the surface measurements is investigated by comparison with information obtained from satellite backscattered UV observations on the Nimbus 4 with nearly complete global coverage for the period 1970-1972. Results show that the geographical distribution of the stations does not properly represent different latitudes. While the number of stations in the north temperate zone appears adequate to represent monthly ozone averages to within 0.5% except during the early phase of the Northern Hemisphere spring maximum, the resultant error in the derived change in north temperature zone ozone between 1970-1972 is 0.5%. In the tropical and south temperate zones the smaller number of stations reduces precision, and the ozone averages for use in deriving seasonal variability and trends are uncertain by about 1%. However, in the south temperature zone, the average from the sample may differ as much as 5% in some months from the averages derived from the full set. It is concluded that the resulting uncertainty in the global averages is comparable in size to typical yearly changes.

Description: Type II Cepheids with periods between 1 and 3 days, commonly designated as Bl Herculis stars, have been modeled here with the aim of interpreting the wide variety of light curves observed among the field variables. Previously modeled globular cluster members are used as standard calibration objects. The major finding is that only a small range of luminosities is capable of generating a large variety of light curve types at a given period. For a mass of approximately 0.60 solar mass, the models are able to reproduce the observed mean luminosities, dispersion of mean luminosities, periods, light amplitudes, light asymmetries, and phases of secondary features in the light curves of known BL Her stars. It is possible that the metal-rich variables (which are found only in the field) have luminosities lower than those of most metal-poor variables. The present revised mass for BL Her, a metal-rich object, is not significantly different from the mean mass of the metal-poor variables.

Description: A heuristic criterion, based on linear perturbation analysis, is applied to the initial growth of density perturbations in isothermal or adiabatic gas clouds, with initially uniform density and uniform rotation. The heuristic criterion is shown to be consistent with the available results from numerical calculations of cloud collapse. The criterion predicts that perturbations varying as cos(m-phi) will be most likely to grow when m is small, unless the cloud is nearly pressureless.

Description: (Previously announced in STAR as N82-18085)

Description: It is shown that a natural consequence of the binary pulsar's evolution is a neutron star collision. Such a collision is expected to eject neutron-rich matter of an r-process character. Taking reasonable estimates for the number of such events over the history of the galaxy, it may be that they account for all of the r-process nuclei.

Description: Observations of the variable star R Aquarii from 1928 to the present are examined to conclude that the star is a binary system with a jet. The orbital period of the objects is estimated at 22 yr, and a supercritical mass transfer that occurs once every 44 yr is suggested as a mechanism to explain deep minima observed on two occasions that many years apart. Calculations presented for the critical accretion rate of the two Miras indicated that one of the objects possesses a substantially stronger gravitational field than the other and features a large accretion disk. Oriental astronomical records from 930 AD are cited as evidence that a nova occurred in the vicinity of R Aquarii at that time. The system is noted to be the closest jet thus far observed, and the accretion disk may be visible with the Space Telescope.

Description: Balloon-borne Ultraviolet Stellar Spectrometer observations of the profiles of two well observed spectral lines in the ultraviolet spectrum of Alpha CMI (Procyon; F5IV-V) are analyzed with a Fourier transform method in order to determine values of various parameters of the velocity field of the upper photosphere. A microturbulent line-of-sight velocity component of 0.9 + or - 0.4 km/s, a macroturbulent velocity component of 5.3 + or - 0.2 km/s, and a rotational velocity component of 10.0 + or - 1.2 km/s were determined. In these calculations a single-moded sinusoidal isotropic macroturbulent velocity function was assumed. The result appears to be sensitive to the assumed shape of the macroturbulence function.

Description: Exposures on the spectra of four late C-type stars have been made with the IUE satellite in the wavelength range of the LWR camera (1900-3200 A). Two Mira variables near maximum light and two semiregular variables were observed. Although the exposure times used, which range up to 240 min in the low-resolution mode, were more than sufficient to record the continuum and emission lines of Mg II, Fe II, and Al II in normal M stars of similar magnitude and temperature, no light was recorded. It is concluded that the far-ultraviolet continuum is strongly depressed in these cool carbon stars. The absence of UV emission lines implies either that the chromospheric lines observed in M stars require an ultraviolet flux for their excitation, or that cool carbon stars have no chromosphere at all or that the opacity source is located above even the emission-line-forming region. This opacity source, which is probably some carbon condensate since it is weak or absent in M stars while absorbing strongly in C stars, is discussed both in terms of the chromospheric interpretation of the emission lines and in terms of their shock-wave interpretation.

Description: The effects of the earth's atmosphere on the Thematic Mapper (TM) measurements are studied with two radiative transfer models. A doubling model is used to compute the effective reflectance of the earth-atmosphere system, as measured by the TM for the reflective bands. An emission-transmission model is used to compute the satellite-received radiance for the thermal band. The influences of the aerosol loading, the amount of water vapor, and the solar illumination angle on the effective reflectance are investigated. The effect of varying atmospheric water vapor on the measurements of the thermal band is studied. The scattering and absorption effects on TM bands are compared with those on Multispectral Scanner System (MSS) bands. While the changes in the aerosol loading introduce comparable variation of the effective reflectance for both sensors, the changes in the water vapor amount give less impact on TM4 than MSS7.

Description: Solar ultraviolet flux data obtained within the atmosphere by using Fastie-Ebert double monochromators carried on a balloon-borne gondola and a rocket payload are analyzed. Both the direct and scattered components of the solar ultraviolet flux at wavelengths from 190 to 320 nm are measured at the balloon float altitude of 40 km. The nearly identical spectrometer carried on the rocket flight measures the direct solar flux from 60 to 38 km during a parachute descent. The ozone column content above 40 km and the temperature profile and ozone density below 40 km are deduced using the scattered and direct solar flux components. It is shown that the Nimbus 7 solar flux data are consistent with the present data and with the ozone absorption cross sections of Inn and Tanake (1959). The calculated and measured values of the scattered solar flux are found to agree fairly closely.

Description: The influence of the choice of the Lagrange multiplier on constrained linear inversions is explored, with reference made to applications in inferring the columnar aerosol size distributions from spectral aerosol optical depth measurements. A range of the Lagrange multiplier is examined to find all positive solutions for the solution vector, which represents modifying factors to the assumed form of the size distribution. An iterative method is devised to constrain the calculations to consideration of only positive quantities and a requirement that the regression fit to data be consistent with measurement errors. The determination of the variances and covariances is formulated and applied to existing data sets for optical depth. Variances in the solution are found to be large for particle radii when the information content of the data is small.

Description: It is shown that the radio structure of 3C 449 can be matched with a model in which the jets are precessing and have relativistic (beta greater-than or equal to 0.4) velocities. The best-fit model implies a precession period of about 100,000 yr and a cone angle which increases with time. A similar model may be relevant for the radio structure of 3C 31. A brief discussion of the implications for 3C 449 is given.

Description: The evolutions of the envelopes of collapsing, accreting, isothermal clouds have been numerically calculated for both spherically symmetric and rotating (axisymmetric) clouds. The results provide a cohesive picture of isothermal collapse, and their relationship to previous numerical calculations and similarity solutions is discussed. Even with a large initial rotation rate, the majority of the cloud envelope is accreted, in one case leaving behind a large-scale circulation current. The calculations are performed for both initially uniform density and centrally condensed clouds. Density and velocity profiles for a wide variety of observed systems are compared with those obtained in this study, providing a preliminary assessment of the stage of evolution and initial structure for the observed systems.

Description: The infrared spectra of smokes condensed from SiO-H2 and Mg-SiO-H2 vapors and of smoke samples annealed for various times at 1000 K and 1250 K are presented. The spectra of these materials show features in the 8-25 micron interval in addition to the well-known bands near 10 and 20 microns. It is suggested that these features may correspond to weak structures that can be seen in the infrared spectra of oxygen-rich stars. Observations are needed to determine the reality and characteristics of such weak features.

Description: (Previously announced in STAR as N82-18096)

Description: New line assignments in the spectrum of the stratospheric submillimeter emission, measured with unapodized resolution of 0.0033/cm, have been made. Positive evidence for the presence of symmetric and asymmetric ozone isotopes, water vapor excited to the (010) level, and HCN is given.

Description: Possible damages to wind turbine components due to lightning strikes are discussed and means to prevent the damage are presented. A low resistance path to the ground is noted to be essential for any turbine system, including metal paths on nonmetal blades to conduct the strike. Surge arrestors are necessary to protect against overvoltages both from utility lines in normal operation and against lightning damage to control equipment and contactors in the generator. MOS structures are susceptible to static discharge injury, as are other semiconductor devices, and must be protected by the presence of static protection circuitry. It is recommended that the electronics be analyzed for the circuit transient response to a lightning waveform, to induced and dc current injection, that input/output leads be shielded, everything be grounded, and lightning-resistant components be chosen early in the design phase.

Description: It is shown that the Jeans mass for gravitational collapse can be very much reduced by the influence velocity fields, even when allowance is made for non-isothermal gas behavior. We examine the role of turbulence in establishing the initial stellar mass function and show that the flattening and/or turnover at the low mass end may be a signature of interstellar turbulence. We consider also the implications of primordial turbulence for the formation of stars in the early universe.

Description: During its April 1979 eruption series, Soufriere Volcano produced two major stratospheric plumes that the SAGE (Stratospheric Aerosol and Gas Experiment) satellite system tracked to West Africa and the North Atlantic Ocean. The total mass of these plumes, whose movement and dispersion are in agreement with those deduced from meteorological data and dispersion theory, was less than 0.5 percent of the global stratospheric aerosol burden; no significant temperature or climate perturbation is therefore expected.

Description: At the time of the Soufriere, St. Vincent, volcanic eruption of April 17, 1979, a NASA P-3 aircraft with an uplooking lidar (light detection and ranging) system onboard was airborne 130 kilometers east of the island. Lidar measurements of the fresh volcanic ash were made approximately 2 hours after the eruption, 120 kilometers to the northeast and east. On the evening of April 18, the airborne lidar, on a southerly flight track, detected significant amounts of stratospheric material in layers at 16, 17, 18, and 19.5 kilometers. These data, and measurements to the north on April 19, indicate that the volcanic plume penetrated the stratosphere to an altitude of about 20 kilometers and moved south during the first 48 hours after the eruption.

Description: The coma of a comet is modeled assuming the icy nucleus contains interstellar molecules. This composition overcomes discrepancies between observation and earlier model predictions for CN, C2, C3, and NH2 abundances. It is found that the abundances of CN, C2, and C3-bearing compounds in the nucleus must be constrained to trace amounts in order to account for the observed column densities. NH3 also cannot be abundant by more than about 1%. The model gives good agreement with observed relative ranges of neutral species in the coma as well as with their observed relative intensity dependence on heliocentric distance. The size of the nucleus and the heliocentric ranges considered are relevant to comet Halley.

Description: A computer-aided-design study on the dependence of the efficiency peak of a back-surface field solar cell on the concentrations of the recombination and dopant impurities is presented. The illuminated current-voltage characteristics of more than 100 cell designs are obtained using the transmission line circuit model to numerically solve the Shockley equations. Using an AM 1 efficiency of 17% as a target value, it is shown that the efficiency versus thickness dependence has a broad maximum which varies by less than 1% over more than a three-to-one range of cell thicknesses from 30 to 100 microns. An optically reflecting back surface will give only a slight improvement of AM 1 efficiency, about 0.7%, in this thickness range. Attention is given to the dependence of the efficiency on patchiness across the back-surface field low-high junction in thin cells.

Description: (Previously announced in STAR as N82-18097)

Description: Advances in satellite tracking data accuracy and coverage over the past 15 years have led to major improvements in global geopotential models. But the spacial resolution of the gravity field obtained solely from satellite dynamics sensed by tracking data is still of the order of 1000 km. Attention is given to an approach which will provide information regarding the fine structure of the gravity field on the basis of an application of local corrections to the global field. According to this approach, a basic satellite to satellite tracked (SST) range-rate measurement is constructed from the link between a ground station, a geosynchronous satellite (ATS 6), and a near-earth satellite (Apollo or GEOS 3). Attention is given to a mathematical model, the simulation of SST gravity anomaly estimation accuracies, a gravity anomaly estimation from GEOS 3/ATS 6 and Apollo/ATS 6 SST observations, and an evaluation of the mean gravity anomalies determined from SST.

Description: Maps of five H II regions in one or more of the infrared fine-structure lines of Ne II (12.8 microns), Ar III (9.0 microns), and S IV (10.5 microns) have been obtained with angular resolutions ranging from 4 to 7 arcsec. The observations are used to discuss the morphology and excitation of these nebulae. Considerable diversity is found in the structures of the nebulae, probably resulting from differences in their ages and the circumstances of their formation. In all cases, more ionizing luminosity than would be provided by a single dominant ionizing star appears to be required, although uncertainties in the model nebulae make this conclusion uncertain.

Description: Global magnetic component anomaly field maps have been derived from the Magsat vector magnetometer data obtained from November 1979 through May 1980. The amplitude of variations of the components over the maps are between 10 and 15 nT, well above the noise in the data. Averaged data, in 2-by-2 deg blocks, exhibit standard errors of the mean of about 1 nT over most of the X and Z maps, and about 2 nT over most of the Y maps. Errors rise to about twice these amounts near the auroral belts. Most of the anomalies in the component data are consistent with a crustal magnetization model which incorporates dipoles aligned only in the direction of the main field. However, there appear to be some regions which require dipoles aligned in some other direction i.e., remanent magnetization.

Description: Initial results of the Magsat mission are presented, in keeping with the categories of earth core field, the crustal or anomaly field of the earth, and external fields. It is noted that one major advantage of orbital magnetic field surveys is their ability to obtain a global set of magnetic field measurements of uniform precision and accuracy at a single epoch, aiding the derivation of the core field models that are a prerequisite for further data analysis. The ability to isolate fields from crustal sources was unexpected, because of the low amplitudes of such fields by comparison with those of the core and those external to the earth. The most significant external-field finding has been an east-west component variation near the dip equator.

Description: Studies of Birkeland current systems have been conducted primarily with low altitude satellite magnetometer data whereas electrojet current signatures have been usually analyzed with data from ground-based magnetometer chains. However, the Magsat magnetometer data set allows magnetic disturbances due to both field-aligned and electrojet currents to be examined simultaneously. This is mainly due to Magsat's approximately 400 km altitude, thus providing data closer to the electrojet current system than has been previously available from satellite measurements. Of additional importance are the superior accuracy, both in sensitivity and altitude, of the magnetic field measurements obtained by Magsat and last, but not least, the availability of an accurate magnetic field model of the concurrent epoch (based on the Magsat data set) that allows one to obtain a better baseline than previous models. The aforementioned points are emphasized and both Birkeland and electrojet currents have been analyzed in a case study for November 13, 1979.

Description: Transverse magnetic disturbances associated with Birkeland currents have been measured by the Magsat and TRIAD spacecraft, whose orbits were nearly coplanar from November to mid-December, 1979. A comparison of data received when the satellites were over the TRIAD/Chatanika receiving station shows that 75% of magnetic disturbance measurements are similar in shape and magnitude, with TRIAD peak disturbances being on average 7% larger than those of Magsat. This discrepancy is lower than measurement uncertainties due to baselines and calibration. During periods of higher Kp, despite time separations of as much as 45 min, better agreement is found in the large-scale and well-defined field-aligned current signatures.

Description: An analytical method for the analysis of absorption spectra obtained from the interferograms of an interferometer operated in the solar occultation mode, in which an interferogram is smeared with individual interferogram components generated by the passage of rays at different tangent altitudes, is described. The creation of strong sidelobes on absorption lines by the interferogram smearing leads to the recommendation of a strong apodization on the interferogram for the solar occultation experiment. The application of these concepts to the simultaneous retrieval of temperature and pressure from CO2 4.3-micron band stratospheric absorption spectra includes the analysis of the continuum absorptions by the pressure-induced N2 fundamental bands and by far wings of the CO2 v3 band. Agreement is reported between observed and simulated spectra.

Description: The effect of attenuation in precipitation regions of the sea, which must be considered in order to measure the radar backscatter from the ocean with sufficient accuracy to allow determination of the wind vector, can be ascertained from a knowledge of the brightness temperature observed by a microwave radiometer such as the Seasat multifrequency scanning radiometer. Two algorithms relating radiometric measurements and attenuation, and thereby correcting measured scattering coefficient values, were compared with wind vectors reported by surface observers and those determined by the Seasat scatterometer measurements with and without correction for atmospheric attenuation. Although the attenuation correction yields some improvements, it is constrained by both radiometer footprint differences and different scan patterns.

Description: It is found that the difference between the wet tropospheric corrections obtained with the Seasat Multichannel Microwave Radiometer (SMMR) algorithm and corrections based on near-coincident radiosonde meteorological measurements has a standard deviation of 2.79 cm, which is consistent with the independent value for water vapor determination accuracy reported by the SMMR Evaluation Team. Because the difference between the radiosonde corrections and those obtained by means of interpolated surface meteorological data has a standard deviation of 5.73 cm, the SMMR wet tropospheric correction is recommended for investigations sensitive to the wet tropospheric height correction accuracy.

Description: Deep exposures with the Einstein Observatory show evidence for diffuse X-ray emission from three globular clusters. One possible interpretation of these observations is that the interaction between a cluster wind and a hot gaseous galactic halo is being observed. The one cluster for which the proper motion has been measured is consistent with this interpretation.

Description: A systematic survey of short-period, semiregular variable stars has been made resulting in the detection of six new water masers. Of the 14 short-period maser stars now known, nine are classified as SRb variables. All are very late spectral type SRb's, typically M7, while the overwhelming majority of normal SRb stars is M4 to M6. Their 2.2-11 micron color indices are among the lowest of any known maser stars. They are presumably less dusty as well. Four of the SRb stars and two of the remainder do not obey the correlation between period and velocity spread of the emission features that is found for the Mira and long-period, semiregular variables. Finally, high galactic latitudes dominate; 13 of the 14 are in excess of 13 deg, and nine of these are greater than 25 deg. These facts suggest that the short-period semiregular variables - particularly in SRb stars - may be a very different type of maser star than the Mira and long-period semiregular variables.

Description: An analysis of X-ray observations shows that the steady flux from 4U 1915-05 undergoes periodic absorption dips with a period of 50 minutes. This period most probably represents the underlying orbital period of the system, and variations in the depth and duration of these events suggest that they are caused by a bulge on the edge of the accretion disk at the point where the gas stream impacts the disk. The mass-losing star in this system is probably a low-mass white dwarf, and the spectrum of the dips indicates that the metallicity of the absorbing material is at least a factor of 17 below solar values. The discovery of the 50-minute binary period supports earlier suggestions that X-ray burst sources are in binary systems.

Description: Models for fundamental physical interactions allow for the existence of stable or nearly stable elementary particles much heavier than the proton. Stellar spectra were searched for a positively charged superheavy particle, X(+), which, with a bound electron, should appear as apparently superheavy neutral hydrogen in the interstellar medium. An upper limit for the abundance of X relative to normal hydrogen in the line of sight toward the bright star gamma Cassiopeiae is 2 x 10 to the -8th.

Description: The problem of electrodynamic coupling of stellar coronal loops where beta is less than 1 to underlying velocity fields where beta is greater than approximately 1 is treated. A rigorous analysis reveals that the physics can be represented by a simple yet equivalent LRC circuit analog. This derived analog suggests the existence of global structure oscillations which resonantly excite internal field line oscillations at a spatial resonance within the coronal loop. Even though the width of this spatial resonance, as well as the induced currents and coronal velocity field, within the resonance region explicitly depends on viscosity and resistivity, the resonant form of the generalized electrodynamic heating functions is virtually independent of irreversibilities. This is a classic feature of high-quality resonators that are driven externally by a broad-band source of spectral power.

Description: IUE observations toward 10 stars have shown that zinc is not depleted in the interstellar medium by more than a factor of two, suggesting that its abundance may serve as a tracer of the true metallicity in the gas. A result pertinent to the history of nucleosynthesis in the solar neighborhood is that the local interstellar medium has abundances that appear to be homogeneous to within a factor of two, when integrated over paths of about 500 pc.

Description: Rapid intensity fluctuations in the optical emission, N2/+/ (4278 A), H-beta (4861 A), and OI (5577 A) have been observed with rocket-borne photometers during a passage through a homogeneous auroral arc. The measurements indicate that relatively weak (2-5%) intensity fluctuations of random nature, with dominant frequencies in the 2-20 Hz range, do exist in the optical emissions of quiet-form auroras. These variations have well-defined averaged spectral characteristics and apparently differ from the strong quasi-periodic type of variations seen during pulsing auroras. It is argued that the observed fluctuations, which are usually composed of weak short-lived microbursts, reflect the temporal and spatial microstructure which apparently exists always within auroral arcs.

Description: The development of pair-photon cascades initiated by high energy electrons above a pulsar polar cap is simulated numerically. The calculation uses the energy of the primary electron, the magnetic field strength, and the period of rotation as parameters, and follows the curvature radiation emitted by the primary, the conversion of this radiation to e(+)e(-) pairs in the intense fields, and the quantized synchrotron radiation by the secondary pairs. A recursive technique allows the tracing of an indefinite number of generations using a Monte Carlo method. Gamma-ray and pair spectra are calculated for cascades in different parts of the polar cap and with different acceleration models. It is found that synchrotron radiation from secondary pairs makes an important contribution to the gamma-ray spectrum above 25 MeV, and that the final gamma-ray and pair spectra are insensitive to the height of the accelerating region, as long as the acceleration of the primary electrons is not limited by radiation reaction.

Description: Theoretical models of stellar atmospheres and the process of forming a spectrum are reviewed with particular reference to the spectra of B stars. In the case of classical models the stellar atmosphere is though to consist of plane parallel layers of gas in which radiative and hydrostatic equilibrium exists. No radiative energy is lost or gained in the model atmosphere, but the detailed shape of the spectrum is changed as a result of the interactions with the ionized gas. Predicted line spectra using statistical equilibrium local thermodynamic equilibrium (LTE), and non-LTE physics are compared and the determination of abundances is discussed. The limitations of classical modeling are examined. Models developed to demonstrate what motions in the upper atmosphere will do to the spectrum and to explore the effects of using geometries different from plane parallel layer are reviewed. In particular the problem of radiative transfer is addressed.

Description: Measurements were made of the aerosol size, height and geographical distribution, their composition and optical properties, and their temporal variation with season and following large volcanic eruptions. Sulfur-bearing gases were measured in situ in the stratosphere, and studied of the chemical and physical processes which control gas-to-particle conversion were carried out in the laboratory.

Description: The Instruments are divided into two groups, ground based instruments and satellite-borne instruments. The ground based instruments include a Dobson ozone spectrophotometer, a filter ozonometer, and ozonesondes. The satellite-borne instruments include: a backscatter ultraviolet spectrometer, a high resolution infrared radiation sounder, a infrared interferometer spectrometer, a limb radiance inversion radiometer, and multichannel filter radiometer. A list of investigations using stratospheric satellite data is presented.

Description: The present state of knowledge concerning the absolute magnitude and temporal variability of the solar spectral irradiance is outlined with emphasis on wavelengths relevant to the mesosphere and stratosphere. Reference spectra for the wavelength region 175 to 850 nm are presented including estimates for solar maximum and solar minimum conditions. Values for the Lyman alpha emission are given separately.

Description: A compilation of rate constant data for use in stratospheric modeling is presented. The tabulations are divided into two categories: bimolecular and termolecular. Explanations are given for anomalous pressure and temperature dependences.

Description: Tropospheric and stratospheric source gases and their distribution are reported. A comparison of measurements and model calculations for stratospheric gases is presented.

Description: The capability for obtaining four-dimensional data on stratospheric structure, dynamics, and zone is discussed. Progress in the development of multidimensional models of the stratosphere is reported. The discussion of multidimensional aspects of the stratosphere is divided into four major sections: observations, analysis and interpretation, modeling, and transport of trace species.