ALBERT

Description: Voyager 1 images show 14 volcanic centers wholly or partly within the Kane Patera quadrangle of Io, which are divided into four major classes: (1) shield with parallel flows; (2) shield with early radial fan shapd flows; (3) shield with radial fan shaped flows, surfaces of flows textured with longitudinal ridges; and (4) depression surrounded by plateau-forming scarp-bounded, untextured deposits. The interpretation attempted here hinges largely on the ability to distinguish lava flows from pyroclastic flows by remote sensing.

Description: Structural and tectonic interpretations of planetary surfaces rely strongly on visual determination of regional structural grain. This grain can be very complex and confusing, and sorting out of discrete trends in time and space is of utmost importance. This study is a test of these techniques applied to a well known area having several discrete structural grains. In the Bighorn Basin region of Wyoming, a largely overlooked N10E structural grain has been verified with detailed structural analysis and indicates a significant change in stress orientation at the end of the Laramide orogeny.

Description: Tectoism in the Valles Marineris appears to have been accompanied by volcanism. The proposed volcanic features, though probably contemporaneous with the gigantic ones in the Tharsis area, are composed of small, mafic and, possibly, somewhat larger felsic flows. The size of these features is similar to that of volcanic flows on the Earth.

Description: Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

Description: The use of laser holography for measuring the distortion of antennas under space simulation conditions is described. The subject is the so-called double exposure procedure which allows to measure the distortion in the order of 1 to 30/micrometers + or - 0.5 per hologramme of an area of 4 m diameter max. The method of holography takes into account the constraints of the space simulation facility. The test method, the test set up and the constraints by the space simulation facility are described. The results of the performed tests are presented and compared with the theoretical predictions. The test on the K-Band Antenna e.g., showed a distortion of approximately 140/micrometers + or - 5/micrometers measured during the cool down from -10 C to -120 C.

Description: Conventional schemes for digitizing large volumes of photographic data are far too costly and time consuming to encourage the undertaking of the ambitious projects using traditional technology. There is a distinct need for fast digitizing systems such as could be derived from development of large format, optically multiplexed CCD systems designed to address these problems. The use of CCD chips for data handling and the capability of using polaroids in the optical path for reduced light scattering are discussed.

Description: Parameters of the UK 1.2 meter Schmidt telescope are described. Plates taken with this instrument are in two categories, those for systematic sky surveys and those taken at the request of research users. A collaborative project with the European Southern Observatory was undertaken to obtain a two-color survey of the sky south of -20 deg declination to complement the Palomar survey. A near infrared survey of the Galactic Plane and the Megallanic Clouds is being done. The area south of -20 deg and the zone between 0 deg and -15 deg are also being surveyed. Pending a decision on survey parameters, all available A quality prism plates are being retained to form a basis for systematic survey. Nearly half the plates taken on a service basis for the UK astronomical community are to fulfill nonsurvey requests. Plates taken for surveys which are not of A grade quality are also made available for research purposes.

Description: Some software facilities used mainly for information retrieval and analysis at the Padova-Asiago Observatory are discussed. These facilities help guest and resident astronomers to make easier the preparation of plate measurements. The problems connected with the creation, use and management of a data base in a scientific (astronomical) environment are reviewed on the basis of the experience gathered during the last three years. The development plan of the user session environment and its possible applications in a computer network are briefly sketched.

Description: A 256 diode-array will be installed as detector on the ESO OPTRONICS S-3000 measuring machine in order to increase the acquisition rate. A high intensity LED will be used as light source in a pulse mode. The data will be stored on a random access mass storage device as density values for later education. The scanning time for a 30 cm x 30 cm plate with a step size of 10 micron will be less than 10 hours while the dynamic range of the data is expected to be 2.5 density units with an offset of at least 1 unit.

Description: The design and performance of the automated photographic measuring facility at Cambridge is described. It consists of a precision laser scanning microdensitometer connected to a series of computers that process the data on-line. Plates up to 350 mm square can be measured. The microdensitometer samples the plate to 12 bit accuracy at a speed of 230,000 samples/second. The positional accuracy is better than a micron. Other features include platen rotation and automatic focus.

Description: The expected performance of the Minnesota automated dual-plate scanner (APS) is discussed with regard to photometry, position measurement accuracy, and ability to classify images. In addition, a fast algorithm for calculating image parameters is described.

Description: Various aspects of the performance of the PDS 1010A microdensitometer are described. The primary points in an upgrade propsal for the unit are outlined. Photometric instabilities in the PDS are mentioned.

Description: Minor modifications of electronic components in the PDS 1010A microdensitometer are discussed. The operational requirements and performance limitations of the PDS are noted. Replacement of the photomultiplier and front-end analog circuitry significantly improved the photometric performance of the PDS. The improvement in density repeatability is marked, and the permissible density slew speed is greatly increased.

Description: High Altitude Observatory HAO microdensitometer undergoes monthly testing to assure its consistent performance. These tests check positional and photometric stability at the 10 micron aperture level. The HAO test procedure is designed to run without operator intervention following initial configuration of the microdensitometer for each subprocedure. Specialized test software is resident in the PDP 8. The operator selects the proper subprocedure by entering commands. Once computer control is established, it is not relinquished until the test is complete.

Description: A number of diagnostic tests are developed for the Photometric Data System PDS 2020G microdensitometer to monitor its performance and to isolate various electromechanical problems. A number of tests which help to diagnose problems with the photometer, positional accuracy and data collection are described. The tests include: (1) scanning a razor blade edge to study the response of the photometer and zero point losses in the coordinate system, (2) scanning a long straight line to evaluate the drunkness of the stage motions, (3) scanning photometric step wedge calibrations to study the response of the photometer, and (4) measurement of a series of high signal to noise plates of the same region of the sky to evaluate the overall performance of the microdensitometer. A variety of electronic tests to isolate electromechanical problems are also performed.

Description: The behavior of ruled and holographic gratings with various coatings after extended exposure to the space environments was examined. The coatings and differentiating between the influences of vacuum and solar illumination were examined. In the past, several ruled and holographic gratings with various coatings were successfully flown on rocket experiments. Future utilizations of such gratings are considered for the Space Telescope and for various Spacelab projects under development. The techniques which is used to replicate gratings can also be used to obtain a wide range of lightweight optical components, including sophisticated aspherical, highly polished mirrors.

Description: Electro-optic holographic recording systems were developed. The spaceworthiness of electro-optic crystals for use in ultrahigh capacity space data storage and retrieval systems are examined. The crystals for this experiment are included with the various electro-optical components of LDEF experiment. The effects of long-duration exposure on active optical system components is investigated. The concept of data storage in an optical-phase holographic memory is illustrated.

Description: The specific scientific objectives of this experiment are to measure the spatial distribution, size, velocity, radiance, and composition of microparticles in near-Earth space. The technological objectives are to measure erosion rates resulting from microparticle impacts and to evaluate thin-foil meteor 'bumpers'. The combinations of sensitivity and reliability in this experiment will provide up to 1000 impacts per month for laboratory analysis and will extend current sensitivity limits by 5 orders of magnitude in mass.

Description: Significant new geologic information has been revealed by comparing 1:5 million scale geologic maps of the equatorial zone quadrangles of Mercury (H-6, H-7 and H-8) to Earth-based elevation profiles and surface reflectivity maps of Mercury obtained in the early 1970's at the Arecibo (PR) and Goldstone (CA) radar facilities. These data consist of 23 Goldstone images and profiles of polarized return data at 12.5-cm wavelength and one Arecibo profile. Radar data with 150-m vertical accuracy and 10- to 20-km horizontal resolution are available for areas between latitudes 13 N. and 11 S. In general, these data sets show excellent correlation between: (1) relative elevation and roughness differences that are reflected by mapped geologic contacts; (2) mapped ridges and scarps that display distinctive radar signatures; and (3) position and morphology of crater-and-basin topographic elements. Inferences can also be drawn about topographic and geologic terrain beyond the area imaged by Mariner 10 cameras.

Description: On Mars, the association of gullied escarpments and chaotic terrain is evidence for failure and scarp retreat of poorly consolidated materials. Some martian gullies have no surface outlets and may have drained through subterranean channels. Similar features, though on a much smaller scale, can be seen in alluvium along terrestrial river banks in semiarid regions, such as the Rio Puerco Valley of central New Mexico. Many of the escarpments along the Rio Puerco are developing through formation of collapse gullies, which drain through soil pipes. Gully development can be monitored on aerial photographs taken in 1935, 1962, and 1980. A regression model was developed to quantify gully evolution over a known time span. Soil pipes and their associated collapse gullies make recognizable signatures on the air photos. The areal extent of this signature can be normalized to the scarp length of each pipe-gully system, which makes comparisons between systems possible.

Description: Geomorphic studies of impact structures in central Australia are being used to understand the complexities of fluvial dissection in the heavily cratered terrains of Mars. At Henbury, Northern Territory, approximately 12 small meteorite craters have interacted with a semiarid drainage system. The detailed mapping of the geologic and structural features at Henbury allowed this study to concentrate on degradational landforms. The breaching of crater rims by gullies was facilitated by the northward movement of sheetwash along an extensive pediment surface extending from the Bacon Range. South-facing crater rims have been preferentially breached because gullies on those sides were able to tap the largest amounts of runoff. At crater 6 a probable rim-gully system has captured the headward reaches of a pre-impact stream channel. The interactive history of impacts and drainage development is critical to understanding the relationships in the heavily cratered uplands of Mars. Whereas Henbury craters are younger than 4700 yrs. B.P., the Gosses Bluff structure formed about 130 million years ago. The bluff is essentially an etched central peak composed of resistant sandstone units. Fluvial erosion of this structure is also discussed.

Description: Eastern Acidalia Planitia contains a wide variety of terrain types on which are thousands of subkilometer volcanoes. Apparent morphometric variations were previously reported as a function of terrain type for the cones in the Cydonia area and extended to the rest of Acidalia for which high resolution Viking imagery exist. Crater counts are included for the six types of plains identified, density distributions of subkilometer cones found on each type of terrain, and orphometric data by morphological subclass as a function of terrain for more than 1400 cones.

Description: Preliminary mapping shows East Butte to be a single, large cumulo-dome composed dominantly of rhyolite which can be classified into three main groups based on color and structure. The rhyolite of East Butte is aphanitic with phenocrysts of sanidine and quartz which vary from 1 to 5 mm in length. Vesicular reddish black inclusions of basalt up to 10 cm in length, found in all varieties of the East Butte rhyolites are believed to have originated from fragmentation of the basalt walls of the conduit by rhyolitic magma as it was emplaced. Most of the inclusions contain plagioclase phenocrysts. These phenocrysts measure up to 1 to 2 cm in length and have a typical euhedral, tabular habit. A 250-m diameter depression which has the appearance of a crater is located at the top of East Butte. Evidence supporting the fact that the depression is a crater is displayed by three small (3 to 5 m in height) mounds of massive rhyolite which border the depression.

Description: Some of the geological relationships observed in the Mauna Loa sulfur flow may apply in considering volcanic processes on Io. Given the presence of sulfur/sulfur compounds in the eruption plumes and on the surface of Io, it is likely that extensive secondary deposits of sulfur exist, some of which may be of fumarolic origin and analogous to the Mauna Loa deposit. Given the likelihood of silicate volcanism of Io based on the inferred material properties of some flows, and the attendant high temperatures for silicate volcanism, it is likely that the secondary surface deposits of sulfur would have been mobilized without being heated to the high viscosity stage. Mobilized sulfur flows on Io may flow long distances as a result of: (1) low viscosities in the melting range; (2) sustained effusion resulting from continued heating source area; (3) continued remobilization within the flow as a consequence of surges from the source; and (4) extension via lava tubes, or similar conduits through which there is little heat loss. Sulfur flows may form a relatively thin veneer over silicate flows and other surface units, given their fluidity and low mobilization temperature. Active splashing and splattering may spread sulfur over a wider area contributing the bright blooms observed in association with some Ionian flows.

Description: Perhaps the greatest chance for exhumation, or burial, of a landscape by terrestrial processes exists near the boundaries of the climatic belts. In the Southern Hemisphere, there is comparatively little land area within Budel's zone of extra-tropical valley formation, which contains most of the examples of exhumed topography in the Northern Hemisphere. The only examples of resurrected landforms that occur within Budel's tropical zone are located near the boundary of this zone, where climate may have changed during the Pleistocene. The ages of exhumed landforms sampled are not equally distributed through geologic time. Most of the exhumed features were created either during the Precambrian or the Tertiary periods which are commonly cited as episodes of significant landform development.

Description: The Dry Valleys of Antarctica are examples of polar deserts which are rare geological features on the Earth. Such deserts typically have high salinities associated with their closed-basin waters and on many surficial materials throughout them. In order to examine the possible sources for the salts observed in association with the soils in the Dry Valleys. The chloride and bromide concentrations of the water leachates from 58 soils and core samples were measured. The Cl/Br ratio for seawater is 289 and ratios measured for most of the 58 soils studied (greater than 85% of the soils studied) was larger than the seawater ratio (ratios typically were greater than 1000 and ranged up to 50,000). The enrichment in Cl relative to Br is strong evidence that the alts present within the soils were derived from seawater during ordinary evaporation processes, and not from the deposition of Cl and Br from aerosols or from rock weathering as has often been suggested.

Description: Field studies of terrestrial landforms and the processes that shape them provide new directions to the study of planetary features. Investigations discussed address principally mudflow phenomena and drainage development. At the Valley of 10,000 Smokes (Katmai, AK) and Mount St. Helens, WA, studies of the development of erosional landforms (in particular, drainage) on fresh, new surfaces permitted analysis of the result of competition between geomorphic processes. Of specific interest is the development of stream pattern as a function of the competition between perennial seepage overland flow (from glacial or groundwater sources), ephemeral overland flow (from pluvial or seasonal melt sources), and ephemeral/perennial groundwater sapping, as a function of time since initial resurfacing, material properties, and seasonal/annual environmental conditions.

Description: Desert pavement is a general term describing a surface that typically consists of a thin layer of cm-sized rock fragments set on top of a layer of finer material in which no fragments are found. An understanding of desert pavement is important to planetary geology because they may play a major role in the formation and visibility of various aeolian features such as wind streaks, which are important on Mars and may be important on Venus. A field study was conducted in Amboy, California to determine the formation mechanism of desert pavements. The probable sequence of events for the formation and evolution of a typical desert pavement surface, based on this experiment and the work of others, is as follows. Starting with a layer of surface material consisting of both fine particles and rock fragments, aeolian deflation will rapidly erode the surface until an armored lag is developed, after which aeolian processes become less important. The concentration of fragments then slowly increases as new fragments are brought to the surface from the subsurface and as fragments move downslope by sheet wash. Sheet wash would be responsible for removing very fine particles from the surface and for moving the fragments relative to one another, forming interlocks.

Description: Field studies of terrestrial landforms and the processes that shape them provide new directions to the study of planetary features. These studies, conducted in Iceland and in Antarctica, investigated physical and chemical weathering mechanisms and rates, eolitan processes, mudflow phenomena, drainage development, and catastrophic fluvial and volcanic phenomena. Continuing investigations in Iceland fall in three main catagories: (1) catastrophic floods of the Jokulsa a Fjollum, (2) lahars associated with explosive volcanic eruptions of Askja caldera, and (3) rates of eolian abrasion in cold, volcanic deserts. The ice-free valleys of Antarctica, in particular those in South Victoria Land, have much is common with the surface of Mars. In addition to providing independent support for the application of the Iceland findings to consideration of the martian erosional system, the Antarctic observations also provide analogies to other martian phenomena. For example, a family of sand dunes in Victoria Valley are stabilized by the incorporation of snow as beds.

Description: Development of drainage networks by erosion by emergent groundwater (sapping) is being modelled by a combination of laboratory experiments and theoretical modelling. Miniature drainage networks formed in fine-grained sediments share many morphologic characteristics of Martian and terrestrial networks suspected to be formed by sapping processes. A larger and better instrumented sapping box was constructed to further explore the processes of sapping and the morphology of resulting networks. The experiments to be conducted in the sapping box will investigate the roles of several factors in controlling network morphology. The mechanics of sapping of fine-grained sediments were investigated in experiments in a two-dimensional sapping chamber and through development of a theoretical model. Results of extensive tests on sapping erosion of fine-grained, cohesionless sediment were analyzed with a theoretical model of the mechanics of sapping erosion and transport.

Description: The 18 May 1980 eruption of Mount St. Helens was initiated by a massive rockslide-debris avalanche which completely transformed the upper 25 km of the North Fork Toutle River valley. The debris was generated by one of the largest gravitational mass movements ever recorded on Earth. Moving at an average velocity of 35 m/s, the debris avalanche buried approximately 60 sq km of terrain to an average depth of 45 m with unconsolidated, poorly sorted volcaniclastic material, all within a period of 10 minutes. Where exposed and unaltered by subsequent lahars and pyroclastic flows, the new terrain surface was characterized predominantly by hummocks, closed depressions, and the absence of an identifiable channel network. Following emplacement of the debris avalanche, a complex interrelationship of fluvial and mass wasting processes immediately began operating to return the impacted area to an equilibrium status through the removal of material (potential energy) and re-establishment of graded conditions. In an attempt to chronicle the morphologic evolution of this unique environmental setting, a systematic series of interpretative maps of several selected areas was produced. These maps, which document the rate and character of active geomorphic processes, are discussed.

Description: Pressure ridges are surface features on basaltic lava flows and, as with other surface features, they may be related to the emplacement of a flow and the rheological properties of the lava. Since many ridges are of sufficient size to be detected on high resolution orbital images, an understanding of pressure ridges could provide a means for interpreting volcanic flows on other terrestrial planets. Some proposed formation mechanisms are reviewed and three different types of pressure ridges are identified on the basis of morphology. Type 1 ridges are the most common and are associated with multiple flow unit pahoehoe in which the ridges are embayed by secondary toe fed lava. They tend to be restricted to wider sections or margins of the flow and to be oriented longitudinal to flow direction; however, oblique or transverse orientation is not uncommon. Bulbous squeeze ups are common within cracks and may reflect relative timing of crack formation. The interior structure of type 1 ridges consists of an upper slab section which generally contains columnar joints and a lower massive section with an irregular surface. This basic distinction may mark the thickness of the surface crust when ridge formation was initiated. Type 2 ridges occur in association with type 1 and are very similar with the exception of the secondary squeeze out material. Instead of only filling cracks, the secondary material on these ridges originated from underneath a thin crust and flowed as toes or channels from the top and sides of the ridge. Type 3 ridges have much steeper sides (almost vertical at the top) than the other types. Medial cracks are very wide and the crack walls are convex upward. No squeeze ups are present. The main difference between type 3 and the others may be reflection of viscosity.

Description: A model for the radiative cooling of thermally well mixed lava flows is presented and the relationship between effusion rate and length and area is analyzed. If radiative cooling is the prime mode of heat loss for a lava flow, one should expect to see a stronger correlation between the effusion rate and the plan area of the flow, than between effusion rate and just flow length. Different flows on a single volcano with differing initial temperatures, volatile content, and gross compositions should yield different areas for a given effusion rate. Likewise, a range of slopes for the relationship between effusion rate and flow area should result from comparisons between different volcanoes. As a test of these ideas, available data on the effusion rates, lengths, and areas of Hawaiian and Etnean flow is studied. It was found that: (1) the effusion rate/area correlation was statistically more significant than the correlation between effusion rate and length for four out of the five eruption episodes which met the necessary criteria of more than three individual flows with area, length, and effusion rate independently measured; (2) that there exists a minimum length and area for a given effusion rate, reflecting competition between overall characteristic proportionality between effusion rate and flow length, width, and area.

Description: Between 1217 and 1620 hours (PDT), on May 18, 1980, the magmatic eruption column of Mount St. Helens formed an ash fountain and pyroclastic flows dominated the eruption process over tephra ejection. Eurption-rate pulsations generally increased to a maximum at 1600 to 1700 hrs. After 1620 hrs, the eruption assumed an open-vent discharge with strong, vertical ejection of tephra. Relative eruption rates (relative mass flux rates) of the pyroclastic flows were determined by correlating sequential photographs and SLAR images, obtained during the eruption, with stratigraphy and surface morphology of the deposits.

Description: Reexamination of Upheaval Dome in the Canyonlands National Park, Utah, shows that the structure of this remarkable feature conforms with that expected for a deeply eroded astrobleme. The structure is definitely not compatible with an origin due simply to plastic flowage of salt and other rocks in the underlying Paradox Formation. The most strongly deformed rocks are bounded by a series of circumferential listric faults. The convergent displacement of the rocks corresponds to the deformation that results from collapse of a transient cavity produced by high speed impact. From considerations of the probable depth of exposure of the impact structure and upward extrapolation of the listric faults, the final collapsed crater is estimated to be about 8 to 10 km in diameter; the impacting body was on the order of 0.5 km in diameter.

Description: A brief synopsis of the low Earth orbit (LEO) satellite environment is presented including neutral and ionic species. Two ground based atomic and molecular beam instruments are described which are capable of simulating the interaction of spacecraft surfaces with the LEO environment and detecting the results of these interactions. The first detects mass spectrometrically low level fluxes of reactively and nonreactively surface scattered species as a function of scattering angle and velocity while the second ultrahigh velocity (UHV) molecular beam, laser induced fluorescence apparatus is capable of measuring chemiluminescence produced by either gas phase or gas-surface interactions. A number of proposed experiments are described.

Description: A brief review of atmospheric composition in low Earth orbit is presented. The flux of ambient atomic oxygen incident on a surface orbiting in this environment is described. Estimates are presented of the fluence of atomic oxygen to which satellite surfaces in various orbits are exposed.

Description: One of the principal advantages of electrography when compared to photography is the nearly linear relationship between source intensity versus resulting image density. This property allows for simplified and more accurate photometric calibration and permits a certain degree of extrapolation of the calibration to beyond the limits of the faintest photoelectric standard on an exposure. The desires to extract quantitative photometric information from electrographic (or photographic) negatives and to convert this information into a digital format for computer analysis or enhancement led to the widespread use of scanning microdensitometers to perform this A-to-D conversion. Therefore it is of vital importance to understand and, if practical, to avoid any nonlinearities which may be introduced during microdensitometry of electrographic emulsions.

Description: The scanning of a direct plate with the automatic plate measuring machine which results in the automated selection and description of images is described. The selection of QSO candidates based on color-color diagrams constructed from the APM image data and the analysis of APM raster data for QSOs selected visually from objective prism plates are also discussed.

Description: The fundamental limitations of microdensitometers are reviewed and the design of a high microdensitometer described. The system will digitize to 16 bits in transmission at a speed of 100 kHz using a laser beam moving over the emulsion. Other features are automatic platen rotation and autofocus. The cost will be of order $200,000.

Description: A new photographic measuring machine is under construction at the Paris Observatory. The amount of transmitted light is measured by a linear array of 1024 photodiodes. Carriage control, data acquisition and on line processing are performed by microprocessors, a S.E.L. 32/27 computer, and an AP 120-B Array Processor. It is expected that a Schmidt telescope plate of size 360 mm square will be scanned in one hour with pixel size of ten microns.

Description: A diode-array based image digitizer manufactured by the Eikonix Corp. was tested to see if it can be adapted to the exacting requirements of astronomical densitometry. As the device is presently configured, a dynamic range of 400:1 can be achieved routinely, with a positional accuracy of 2 microns or better. An area of 2048 X 2048 pixels can be scanned in about 5 minutes. Preliminary tests indicate that several relatively simple enhancements can improve both the photometric and the positional accuracy of the device.

Description: Motivations for construction of a next generation microdensitometer (NGM) are presented and their effect on the NGM design is discussed. A prototype of such an engine has been constructed at KPNO. Its design and performance is reviewed.

Description: The motivations for constructing a special purpose built microdensitometer are explored. The salient points of some of the microdensitometers are described and the advantages and disadvantages of the system in comparison to a PDS machine are outlined. The principal gain is in speed though at the expense of loss in dynamic range. The effects on the astronomical results are demonstrated. The astronomical results already obtained with these machines and from ongoing projects are described. It is shown that there is a large class of important astronomical problems which can be tackled by these machines but which are not feasibile on the PDS because of the speed of the machine.

Description: The necessity to incorporate several hardware changes to optimize the Yale PDS 2020G microdensitometer for photometric and astrometric research are discussed. The properties of a new high speed photometer and a positional calibration system are described. The new photometer incorporates a high speed logarithmic analog to digital converter with more than 10 times the resolution of the former system and a cycle time of approximately 50 usec. The positional calibration system monitors the drunkenness of the stages with respect to fixed index lines and enables the correction of the +/- 5 micro stage errors to an accuracy of better than 1 micro.

Description: The astrometric and photometric performance of the PDS 1010A microdensitometer are discussed, including the tests used for checking it. The instrument was shown to satisfy operational requirements for photometric measurements of astronomical plates with respect to dynamic range and stability.

Description: The results of several parametric studies carried out on the Marshall Space Flight Center (MSFC) Photometric Data System PDS-10 microdensitometer are summarized for the purposes of documenting the operation and limitations of the system for inhouse research and to provide a bench mark for comparison with other microdensitometers. The results are grouped into four general areas. These are: (1) system overall stability to drift, (2) photometric linearity and noise, (3) reproducibility, and (4) scanning performance. Test data taken in order to evaluate the interdependency of scan speed, noise and position are included. Shown also are results of tests for system stability, reproducibility, stray light and PMT settling time.

Description: The performance of densitometers used for photometric data reduction of high dynamic range electrographic plate material is analyzed. Densitometer repeatability is tested by comparing two scans of one plate. Internal densitometer errors are examined by constructing histograms of digitized densities and finding inoperative bits and differential nonlinearity in the analog to digital converter. Such problems appear common to the four densitometers used in this investigation and introduce systematic algorithm dependent errors in the results. Strategies to improve densitometer performance are suggested.

Description: Various perturbations which occurred during the operation of a PDS 2020 GM microdensitometer are reviewed. The effects of elevated temperature, vibration, transient electrical noise, and photometric perturbations are briefly discussed. Sample astronomical results from the PDS 2020 GM unit are presented.

Description: Digitizing flatfield images produces conditions in the Photometric Data System PDS which cause the measured density to drift by as much as .1 DN during a 10 minute interval. The drift occurs when the PDS, set up in equilibrium at fog level, subsequently scans a reasonably dense region for periods of longer than a few minutes. The drift is manifested primarily as a positive shift in density that is approximately the same for all densities. If the fog level is assumed to be in fact constant and is monitored during scans of flat fields, the PDS drift may be removed by subtracting the difference between the observed fog level and its assumed constant value for each pixel. This function is then smoothed and subtracted, as a function of scan line, from the measured density. The fog level is then adjusted to a standard value by adding a constant. The result is a flattened scan with PDS drift removed to the accuracy within which the fog level drift matches the drift at other levels.

Description: The photometric and positional accuracy of a microdensitometer is examined. A calibrating plate with different density areas available is used to determine photometric accuracy. Position accuracy is evaluated by multiple scans of sharp edges and analyzed statistically.

Description: Many of the passive experiments flying on LDEF will be significantly enhanced if data are available postflight to indicate the temperature time histories of test materials and other specimens exposed in the experiments. The baseline LDEF approach was to provide postflight calculated temperature histories of experiment boundaries and solar flux data for the mission, which can in turn be used by each investigator to calculate the temperature time histories for critical experiment components. Without in-flight temperature measurements, a substantial uncertainty will exist in the calculated temperatures. The data measured by the themal measurement system (THERM) will significantly improve postflight knowledge of temperatures experienced by LDEF experiments. The THERM data will also be valuable in validating the LDEF thermal design concept and in providing better design data for experimenters on future LDEF missions. The objectives of this experiment are to determine the history of the interior average temperatures of the LDEF for the total orbital mission and to measure the temperatures of selected components and thermal boundary conditions.

Description: Three-dimensional finite element modeling techniques are used to synthesize geodetic and seismological results for 1979 Imperial Valley earthquake. The strategy pursued consists of two principal steps. In the first step, the seismologically-derived coseismic fault slip is taken as a function of position in the fault plane and is applied directly to the three-dimensional dislocation model. In the second step, a physical model of stresses and constitutive parameters is perturbed so as to reproduce the observed fault slip. Hence, the principal features of the coseismic slip pattern are explained by a stress-driven fault model in which: (1) a spatially unresolved asperity is found equivalent to a stress drop of 18 MPa averaged over an area of 15 sq km, and (2) driving stress is essentially absent on the fault segment overlapping the 1940 earthquake rupture zone.

Description: Atmospheric interactions involving the nitrogen species are varied and complex. These interactions include photochemical reactions, initiated by the absorption of solar photons and chemical kinetic reactions, which involve both homogeneous (gas-to-gas reactions) and heterogeneous (gas-to-particle) reactions. Another important atmospheric interaction is the production of nitrogen oxides by atmospheric lightning. The nitrogen cycle strongly couples the biosphere and atmosphere. Many nitrogen species are produced by biogenic processes. Once in the atmosphere nitrogen oxides are photochemically and chemically transformed to nitrates, which are returned to the biosphere via precipitation, dry deposition and aerosols to close the biosphere-atmosphere nitrogen cycle. The sources, sinks and photochemistry/chemistry of the nitrogen species; atmospheric nitrogen species; souces and sinks of nitrous oxide; sources; sinks and photochemistry/chemistry of ammonia; seasonal variation of the vertical distribution of ammonia in the troposphere; surface and atmospheric sources of the nitrogen species, and seasonal variation of ground level ammonia are summarized.

Description: If all biotic sinks of atmospheric CO2 reported were added a value of about 0.4 Gt C/yr would be found. For each category, a very high (non-conservative) estimate was used. This still does not provide a sufficient basis for achieving a balance between the sources and sinks of atmospheric CO2. The bulk of the discrepancy lies in a combination of errors in the major terms, the greatest being in a combination of errors in the major terms, the greatest being in the net biotic release and ocean uptake segments, but smaller errors or biases may exist in calculations of the rate of atmospheric CO2 increase and total fossil fuel use as well. The reason why biotic sinks are not capable of balancing the CO2 increase via nutrient-matching in the short-term is apparent from a comparison of the stoichiometry of the sources and sinks. The burning of fossil fuels and forest biomass releases much more CO2-carbon than is sequestered as organic carbon.

Description: The initial attempts to model the atmospheric CO2 distribution, including couplings to the ocean and biosphere as sources and sinks of atmospheric CO2, encourage the notion that this approach will lead to useful quantitative constraints on CO2 fluxes. Realization of this objective will require: (1) continued improvement in the realism of the global transport modeling; (2) extended timeline of atmospheric CO2 monitoring, which improved precision and improved definition of the uncertainties in the measured CO2 amounts; and (3) given an accurate knowledge of model capabilities and limitations and given a good understanding of CO2 observations and their limitations, there is a need for good ideas concerning what quantitative information on the carbon cycle can be inferred from global modeling.

Description: A science that chooses the globe as it fundamental biogeophysical unit forces extraordinary conceptual difficulties. The roles of energy flow, matter cycles, carbon cycle, air pollution, global effects, air water interactions are discussed.

Description: Measurements of atmospheric aerosol backscatter coefficients, using a coherent CO2 lidar at 9.25- and 10.6-micron wavelengths, are described. Vertical profiles of the volume backscatter coefficient beta have been measured to a 10-km altitude over the Pasadena, CA, region. These measurements indicate a wide range of variability in beta both in and above the local boundary layer. Certain profiles also indicate a significant enhancement in beta at the 9.25-micron wavelength compared with beta at the 10.6-micron wavelength, which possibly indicates a major contribution to the volume backscatter from ammonium sulfate aerosol particles.

Description: While in the lobes of the distant magnetotail, ISEE-3 encountered regions of compressed magnetic field at a rate of several per day. The duration of these events was 5 to 20 minutes and they were observed 10 to 30 minutes following the onset of substorm activity near the earth. During each event, the lobe magnetic field tilted first northward and then southward with the inflection point near the time of peak field strength. Following the compression events, the lobe field weakened and retained a southward component for 20 to 40 minutes. It is suggested that these traveling compression regions are the lobe signatures of plasmoids moving rapidly down the tail in the plasma sheet. Comparison of ISEE-3 compression event times with substorm onset times yielded propagation speeds of 350 to 750 km/s.

Description: Ionospheric rocket sounding data for eight nighttime auroral events are used to characterize relativistic electron showers and their effects on atmospheric ozone. The rockets were launched from the Poker Flat Research Range in Alaska and from Andoya, Norway over the period 1976-82. Energetic fluxes were always detected but were of insufficient magnitude to produce significant changes in stratospheric ozone. However, middle atmospheric energy sources were found to be dominated by relativistic electrons and X-ray bremmstrahlung, the latter from 40-55 km and the former from 55-60 km altitudes. The ionizing radiation is concluded to be a significant factor in mesospheric ion conductivity, mobility, electric field structure and analytical models for the ion-neutral chemistry.

Description: The dynamics of the polar thermosphere are examined by using observations made from the Dynamics Explorer 2 satellite. The results used in this study were obtained primarily from the Fabry-Perot interferometer (FPI) and the wind and temperature spectrometer (WATS) during the time period from September 1981 through January 1982. Two primary geophysical conditions were examined: these were the southern summer and the northern winter polar regions. The results support the conclusion that above 60 degrees of latitude the neutral winds are strongly controlled by ion/neutral frictional momentum transfer resulting from magnetospheric convection. This implies that the natural coordinate system within which to display the neutral winds in the high polar thermosphere is magnetic. The collected observations of this study were used to assess the validity of two of the large thermospheric general circulation models. The result of this assessment was that the models reasonably represent the vector winds at high altitudes but do not, at present, accurately simulate the thermodynamics of that regime.

Description: Previously cited in issue 5, p. 642, Accession no. A83-16486

Description: Line strengths of N2O and its isotopic derivatives in the 1120-1440/cm region were measured at low pressure and high resolution (0.0054/cm). The band strength, rotationless dipole moment matrix elements, and F factor coefficients were considered. First-order nondegenerate perturbation theory was employed to derive explicit expressions for the rotationless dipole moment matrix elements and F factor coefficients. This made it possible to obtain general expressions for the F factor. The derived expressions were also applicable to CO2 bands.

Description: The atmospheric and oceanic mass transport associated with the southern oscillation/El Nino will inevitably induce an interannual variation in the length of day. An empirical correlation study is conducted by comparing the Southern Oscillation Index time series and the interannual length-of-day variation (obtained by removing the long-period and short-period variations from a BIH length-of-day series) for the period 1957-1983. The two series have an encouraging qualitative correlation, in particular with respect to El Nino events; and the linear correlation coefficient is found to be 0.55. It is believed that much, if not most, interannual length-of-day variation is caused by the southern oscillation, and the true correlation is considerably higher than its apparent value considering the fact that the Southern Oscillation Index is merely an indicator derived from two local atmospheric measurements.

Description: Infrared solar absorption spectra recorded at 0.02-per cm resolution during a balloon flight from Alamogordo, NM (33 deg N), on March 23, 1981, have been analyzed for the possible presence of absorption by formic acid (HCOOH). An absorption feature at 1105 per cm has been tentatively identified in upper tropospheric spectra as due to the nu-6 band Q branch. A preliminary analysis indicates a concentration of about 0.6 ppbv and 0.4 ppbv near 8 and 10 km, respectively.

Description: The design of a high spectral resolution, lambda/delta lambda being approximately 1200 IR, sounder capable of increasing the vertical resolution of atmospheric temperature profiles and achieving a rms accuracy of approximately 1.5 K is discussed. This sounder permits improved determination of meteorological parameters on cloudiness, surface temperature, and air-surface interactions. A set of channels from the high J lines in the R branch of the 4.3-micron CO2 band complemented by a larger set of window, humidity, and temperature channels in the 3.7-, 6.3-, 9-, and 15-micron regions is used. Design and simulation studies show that such a sounder is within the present state of the art.

Description: This paper presents the conceptual design of an instrument, called the solar disk sextant, to be used in space to measure the shape and the size of the sun and their variations. The instrumental parameters required to produce sufficient sensitivity to address the problems of solar oblateness, solar pulsations, and global size changes of climatic importance are given.

Description: The UV spectrometer polarimeter on the Solar Maximum Mission has been utilized to measure mesospheric O3 altitude profiles by the technique of solar occultation. Sunset data are presented for 1980, during the fall equinoctal period within + or - 20 deg of the geographic equator. Mean O3 concentrations are (40, 16, 5.5, and 1.5) x 10 to the 9th/cu cm at 50, 55, 60, and 65 km, respectively. Some profiles exhibit altitude structure which is wavelike. The mean O3 profile is fit best with the results of a time-dependent model if the assumed water-vapor mixing ratio employed varies from 6 ppm at 65 km.

Description: A comprehensive formula is worked out for the photochemical time constant of minor constituents in the middle atmosphere. The formula is particularly useful for evaluating the time constants for families of some chemical species that are strongly coupled by rapid exchange reactions. Height profiles of photochemical time constants are calculated for individual species and their families based on the chemical reaction rate constants recommended in the recent WMO and JPL reports. Potential exchange reactions among various family members are discussed, and the effects of the choice of family membership on the time constant are evaluated.

Description: Previously cited in issue 05, p. 643, Accession no. A83-16685

Description: Sixty-four observations of the orbital node made by the Lageos satellite over a five year time interval reveal an acceleration of (-8.1 + or - 1.8) x 10 to the -8 power arcseconds day/2 due to a source which is not presently modeled in the GEODYN orbit determination computer program. This acceleration cannot be explained by the ocean tide with 18.6 year period, assuming it to be an equilibrium tide. Instead it seems to be due to postglacial rebound, which changes the J(2) coefficient in the spherical harmonic expansion of the earth's gravitational field at the rate of (-8.2 + or - 18) x 10 to the -19th power/s; this in turn accelerates the node. This rate does not agree with the -32 x 10 to the -19th power/s predicted by Wu and Peltier's (1982) L2 model, which has upper and lower mantle effective viscosities of 10 to the 21st and 22nd powers Pa's, respectively. It does agree well with their L1 model, which gives about 10 x 10 to the 19th power/s. Since the effective viscosity is 10 to the 21st power Pa s throughout the entire mantle in the L1 model, the results support the contentions that the efective viscosity is near 10 to the 21st power Pa s everyhere in the mantle, and this relatively low value for the effective viscosity may have permitted several degrees of polar wander due to glaciation during the Quaternary Ice Age. Previously announced in STAR as N84-13705

Description: A simple and inexpensive thermal diffusivity apparatus is described for measurement up to 1600 K. The novel features of apparatus include a light pipe, a long furnace, and a differential thermocouple. A low heat-load sample holder for clamping the sample in a vertical position is also described. The results of measurements on AXM-5Q graphite are reported.

Description: ISEE-3 magnetic-field measurements in the region of the geomagnetic tail from -80 to -220 earth radii are reported and discussed. A well-ordered field structure is found, comprising two 7-8-nT lobes separated by a plasma sheet, an embedded neutral sheet with significant By fields, and an intermittent plasma-sheet boundary layer with 5-nT-amplitude (peak-to-peak) electromagnetic waves. The plasma-sheet Bz distribution changes from principally northern orientation near the earth to an approximately equal north-south distribution at 200-220 earth radii. These findings are considered to be in general agreement with magnetic-reconnection models of the magnetosphere, with reconnection either throughout the region observed (in tearing-mode or plasmoid-formation models) or at a constant (about 220-earth-radii) or variable (40-80 to 220-earth-radii) X line (in X-line models).

Description: Using plasma electron and magnetic field measurements from ISEE 3, 220 earth radii from earth, it is found that the magnetotail at that distance is a coherent structure that evidently waves about through distances comparable to its own lateral scale size. For about one-third of the time it was inside the magnetotail, ISEE 3 was in the plasma sheet. During quiet times the plasma sheet is apparently quite thin, but in response to geomagnetic activity it expands, becoming filled with hot plasma flowing tailward at speeds sometimes exceeding 1000 km/sec, and forces the magnetotail cross-section itself to expand. The plasma sheet's expansion is delayed typically by about 30 minutes from the onset of the associated geomagnetic activity (often a clearly identified isolated substorm). The magnetic field in the newly-expanded plasma sheet usually exhibits a few-minute steep northward excursion followed by a more prolonged (and often steep) southward excursion. These are believed to be the signatures of arrival of a plasmoid formed and released near the earth at the onset of the corresponding geomagnetic activity. The discreteness of these plasma releases through the magnetotail and their close association with onsets of geomagnetic activity at earth suggest that they are consequences of spontaneous release, probably by magnetic reconnection, of energy and plasma earlier stored in the magnetotail.

Description: The effects of solar activity on stratospheric ozone were studied between 1970 and 1976 by the NIMBUS 4 backscattered ultraviolet experiment. Results show that, after correcting for instrument sensitivity, globally averaged ozone decreased by 3-4 percent above 2 mbar to less than 1 percent at 10 mbar, as solar activity decreased from solar maximum to solar minimum. This systematic ozone decrease (at all pressure levels) and the seemingly periodic oscillation (generally a 2 year period) seem to be associated with conventional indices of solar activity, which suggests a solar UV-ozone relationship. However, since the ozone depletion, especially at 40 km, is characteristic of atmospheric fluorocarbon injection effects, the solar cycle ozone relationship should be qualified: it may exist if the solar UV flux varies by 15-20 percent in the shorter-wavelength region (less than 200 nm).

Description: The Cold Arctic Mesopause Program (CAMP) was conducted at ESRANGE, Sweden, in July/August 1982. During the time period of several weeks, the temperature was monitored by ground-based OH emission spectrometers and by satellite radiance measurements. Rocket launchings occurred on the nights of 3/4 and 11/12 August. On 3/4 August, seven rocket payloads were launched during a period of noctilucent cloud sighting over ESRANGE. The presence of the NLC was confirmed by several rocket-borne photometer profiles. The temperature measurements showed that the temperature profiles in the stratosphere and lower mesosphere were near the expected values of high latitude summer models. A large amplitude wave structure with three temperature minima of 139K, 114K and 111K were observed at altitudes between 83 and 94 km. The temperature minimum at 83 km was the location of the observed NLC. The temperature minima caused by the growth of the gravity wave amplitude in the highly stable mesosphere provide the regions for the growth of particles by nucleation to optical scattering size, as well as regions where the nuclei for condensation can be formed through ion chemistry paths.

Description: A wave sensor, consisting of parallel, evenly spaced capacitance wires, whose output is the sum of the water surface deflections at the wires, has been built and tested in a wave tank. The probe output simulates Bragg scattering of electromagnetic waves from a water surface with waves; it can be used to simulate electromagnetic probing of the sea surface by radar. The study establishes that the wave probe, called the 'Harp' for short, will simulate Bragg scattering and that it can also be used to study nonlinear wave processes.

Description: The standard balloon-borne radiosonde employed for synoptic meteorology provides vertical profiles of temperature, pressure, and humidity as a function of elapsed time. These parameters are used in the hypsometric equation to calculate the geopotential altitude at each sampling point during the balloon's flight. It is important that the vertical location information be accurate. The present investigation was conducted with the objective to evaluate the altitude determination accuracy of the standard radiosonde throughout the entire balloon profile. The tests included two other commercially available pressure sensors to see if they could provide improved accuracy in the stratosphere. The pressure-measuring performance of standard baroswitches, premium baroswitches, and hypsometers in balloon-borne sondes was correlated with tracking radars. It was found that the standard and premium baroswitches perform well up to about 25 km altitude, while hypsometers provide more reliable data above 25 km.

Description: Ocean floor basalts studied from the Galapagos Ridge, FAMOUS area, Cayman Trough and Kilauea east rift contain 20-200 ppm carbon and 0.3-2.8 ppn nitrogen as sums of the vesicle-filling gases CO2 and N2 and dissolved species. The wide range of carbon contents found is due partly to the different extent of outgassing of vesicle-filling gases and partly to depth dependency of dissolved CO2 in the basalts. Sulfate commonly exists with sulfide in these basalts, and the sulfate/sulfide ratio increases with increasing water content, perhaps reflecting the higher oxidation potential in basalt melt of the higher water content.

Description: ISEE-3 measurements indicate that a broad mantle-like boundary layer plasma often exists within the distant geomagnetic tail lobes at all latitudes, directly adjacent to the tail magnetopause. The presence of this boundary layer at large tail distances indicates that plasma from the magnetosheath often crosses the magnetopause locally along much of the length of the tail, and is evidence that the tail is 'open'.

Description: This paper presents an algorithm for azimuth correlation of synthetic aperture radar (SAR) data with extraordinarily large-range migration which cannot be accommodated by the existing frequency domain interpolation approach used in current Seasat SAR processing. A mathematical model is provided for the SAR range-correlated point-target response both in the spatial and frequency domains. A simple and efficient processing algorithm derived from the exact two-dimensional correlation algorithm is given. This algorithm enables azimuth correlation by two cascaded one-dimensional correlation steps. The first step is to transform the range-correlated SAR data into the frequency domain in azimuth, followed by a newly developed range convolution filter to correct the range-dispersed spectrum of the range-correlated point-target response (RCPTR). The second step is the frequency-domain range migration correction approach for the azimuth compression. Simulation results provided here indicate that this processing algorithm yields a satisfactory compressed impulse response for SAR data with large-range migration whereas previous methods were subject to a broadening of the impulse response along range.

Description: Line parameters for the nu(5) and 2nu(9) bands and associated hot bands of HNO3 have been calculated and compared with laboratory spectra, and the results are presented. Spectral intervals near 870/cm for which best agreement was obtained are used to quantitatively analyze HNO3 absorption features in 0.02/cm resolution stratospheric solar absorption spectra.

Description: Ozone data were obtained in the free troposphere at altitudes of 5 to 7.5 km and at latitudes from 44 degrees N to 46 degrees S during a 3-week period from October 19 to November 4, 1982. Flight trajectories included the continental U.S., Central America, and the western coast of South America. Maximum observed ozone was 110 ppb at about 41 degrees S latitude and at an altitude of 7.3 km (msl). Analysis of the data as a function of latitude showed a region of elevated ozone in the southern latitudes extending from about 2 degrees to 30 degrees in which latitudinal ozone averages (2 degree bands) peaked at about 80 ppb. Ozone concentrations, measured at northern latitudes, were lower, averaging about 35 ppb. A discussion of the data, including comparison with other ozone data sets, is presented.

Description: Total vertical column amounts of NO have been derived from infrared solar absorption spectra recorded near sunrise and sunset with the 0.01 per cm resolution Fourier transform interferometer at the national Solar Observatory on Kitt peak (elevation 2095 m, latitude 31.9 degrees N) on February 23, 1981. The results show an increase in NO concentration in the morning, late afternoon values about 40 percent higher than in the morning, and a decrease in NO concentration prior to sunset. The measured diurnal changes in the total vertical column amount are compared with values obtained from time-dependent photochemical calculations.

Description: Measurements of SO2 emission rates and concentrations and of particle distribution, size, shape, and composition were made in quiescent volcanic plumes emitted into the troposphere from Poas and Arenal volcanos, Costa Rica, and Colima volcano, Mexico. SO2 emission rates were 700 + or - 180 metric tons per day (t/d) for Poas, 210 + or - 30 t/d for Arenal, and 320 + or - 50 t/d for Colima. The concentrations of SO2 calculated from the COSPEC/lidar data were 5-380 ppb. Concentrations of SO2 measured directly by flame photometry were 10-250 ppb. Particles collected in the plumes with a quartz crystal microbalance impactor were mostly less than 3 microns in diameter and consisted of droplets of dilute sulfur-bearing solutions and minor amounts of layer silicate particles coated with a sulfur-bearing film or crust. Total particle concentrations were 4.7 micrograms per cu.m for Poas and 18.8 micrograms per cu.m for Colima. Comparison of concentrations of SO2 in the plumes with gas samples collected at fumaroles on the ground suggests that the plumes are diluted by the atmosphere by factors of up to 100,000.

Description: A two-dimensional photochemical model based on diabatic circulation has been used to simulate the behavior of N2O, CFCl3(F-11) and CF2Cl2(F-12) The circulation is based on estimates of net heating from the ground to 60 km. Eddy diffusion has been reduced with respect to other model studies with Kzz = 2000 sq cm/s everywhere bove 100 mbar. Resulting tracer profiles show reasonable agreement with measured profiles in the tropics and fall off much more sharply with altitude than those produced by models using larger values of Kzz. The agreement obtained is at least as good as that obtained with adjustable, eddy diffusion parameters. The diabatic circulation treatment is more closely related to related to real physical processes and thus more easily interpreted. Diffusive mixing appears to be more important in determining the details of the tracer distributions than the basic morphology.

Description: The mid-latitude upper stratospheric ozone profiles obtained by the solar backscatter ultraviolet instrument on the Nimbus 7 satellite show a clear annual cycle both in the absolute ozone amounts between 0.98 and 15.6 mbar and in the magnitude of disturbances that reveal themselves as longitudinal structure. At the lowest pressure analyzed a winter maximum in ozone exists, but as one progresses downward in altitude a shift in the temporal phase of the annual cycle occurs in the vicinity of 3 to 4 mbar. Comparison of the observed behavior with the predictions of a one-dimensional photochemical model shows a systematic tendency for calculated ozone amount to be 20-27 percent below the data for pressures less than 7.8 mbar. The chemical model successfully predicts the change in phase of the annual cycle, although at a pressure greater than observed. Diagnosis of model results shows the observed shift to be closely coupled to the magnitude of the ozone column density near 3-4 mbar. The wavelength-dependent attenuation of the solar radiation field by ozone alters the relative magnitude of the molecular oxygen and ozone dissociation rates, leading to a change in the temporal phase of the annual cycle.

Description: One-dimensional radiative and photochemical models are used to determine how much CO2 must have been present to maintain a temperate early climate and to examine the consequences that are implied for the controls on atmospheric oxidation state. It is shown that CO2 concentrations of the order of 1000 PAL are required to keep the average surface temperature close to the present value, if albedo changes and heating by reduced greenhouse gases were relatively unimportant. The oxidation state of such a high-CO2, prebiotic atmosphere should have been largely determined by the balance between the H2O2 rainout rate and the rate at which hydrogen escaped to space, with only a weak dependence on the volcanic outgassing rate or on other speculative sources of H2. The implied upper limit on the ground-level O2 mixing ratio is approximately 10 to the -11th and is subject to less uncertainty than the results of previous models.

Description: A time-dependent, one-dimensional photochemical model of the troposphere is used to describe the vertical distribution of atmospheric trace constituents for summer-time conditions at midlatitudes in the Northern Hemisphere. The model incorporates a planetary boundary layer (PBL) parametrization and a detailed chemical mechanism that includes the photochemistry of important nonmethane hydrocarbon species formed during the oxidation process. One result of the parametrized PBL is that the concentrations of some trace species in the free troposphere are 20-30 percent higher than when mixing processes are described by a vertical eddy diffusion coefficient which is held constant with respect to height and time. The lifetime of the oxides of nitrogen against photochemical conversion to nitric acid during summertime conditions is on the order of six hours. This lifetime is short enough to deplete most of the NO(x) in the PBL so that other reactive nitrogen species are more abundant than NO(x) throughout the free troposphere.

Description: A petrologic model of the northern Mississippi Embayment, derived from gravity, seismic and rift data, is evaluated by converting the model to a magnetization model which is compared with satellite magnetic anomaly models. A magnetization contrast of approximately -0.54 A/m, determined from the petrologic model of the embayment compares favorably to values of -0.62 A/m and -0.45 A/m from a Magsat United States Apparent Magnetization Contrast Map and a published POGO magnetization contrast model, respectively. The petrologic model suggests that the magnetic anomaly low associated with the Mississippi Embayment may be largely due to the intrusion under non-oxidizing conditions of low Curie temperature gabbroic material at the base of the crust of the embayment. Near-surface mafic plutons, bordering the Mississippi Valley Graben, appear from aeromagnetic data to have higher magnetizations than the deeper gabbroic material; however, it is impossible to ascertain if this is due to compositional differences or similar material at shallower (lower temperature) depths. These results indicate that variations in the Curie temperatures of intrusions accompanying rifting may account for a large part of the wide range of magnetic anomalies associated with presently inactive rifts with normal heat flow.

Description: A discussion is presented concerning the role of water in its liquid and gaseous states in the chemistry and photochemistry of the earth's troposphere, with attention to the formation of the hydroxyl radical, oxidation chains involving the gases methane, carbon monoxide and ammonia, the atmospheric chemistry of the sulfur, hydrogen, halogen and nitrogen species, and the function of lightning as a source of tropospheric species. The phenomena of 'rainout', 'washout', and the aqueous chemistry of cloud an rain droplets and of water-covered aerosols, are noted. A section is devoted to the past and anticipated impact of anthropogenic activities on the chemistry and composition of the earth's atmosphere.

Description: The laser-induced fluorescence (LIF) of green plants was evaluated as a means of remotely detecting plant stress and determining plant type. Corn and soybeans were used as representatives of monocots and dicots, respectively, in these studies. The fluorescence spectra of several plant pigments was excited with a nitrogen laser emitting at 337 nm. Intact leaves from corn and soybeans also fluoresced using the nitrogen laser. The two plant species exhibited fluorescence spectra which had three maxima in common at 440, 690, and 740 nm. However, the relative intensities of these maxima were distinctly different for the two species. Soybeans had an additional slight maxima at 525 nm. Potassium deficiency in corn caused an increase in fluorescence at 690 and 740 nm. Simulated water stress in soybeans resulted in increased fluorescence at 440, 525, 690, and 740 nm. The inhibition of photosynthesis in soybeans by 3-(3-4-dichlorophenyl)-1-1-dimethyl urea (DCMU) gave incresed fluorescence primarily at 690 and 740 nm. Chlorosis as occurring in senescent soybean leaves caused a decrease in fluorescence at 690 and 740 nm. These studies indicate that LIF measurements of plants offer the potential for remotely detecting certain types of stress condition and also for differentiating plant species.

Description: Using the 9 layer general circulation model developed at the Goddard Laboratory for Atmospheric Sciences (GLAS), several 4 to 5 day integrations were made to assess the impact that latent heating processes (supersaturation and moist convective) have on the model forecasts. In an earlier study by Shukla (1981) it was hypothesized that because of strong interaction between dynamics and moist convection, small initial errors grow very fast and make short range forecasting difficult. The purpose of this study was to examine if prescribed heating rates can improve the forecasts for a few days.

Description: The balloon-borne microwave limb sounder (BMLS) measures atmospheric thermal emission from millimeter wavelength spectral lines to determine vertical profiles of stratospheric species. The instrument flown to date operates at 205 GHz to measure ClO, O3, and H2O2. A 63 GHz radiometer will be added to test the technique for determining tangent point pressure from the MLS experiment on the upper atmosphere research satellite (UARS). Many additional species could also be measured by the BMLS. A radiometer at 270 GHz would provide measurements of HO2, NO2, HNO3, N2O, O-16O-18O-16, and HCN. With this addition, the BMLS can test the current theory of O3 photochemical balance in the upper stratosphere.

Description: The structure of the stratospheric spectrum, measured with a resolution of 0.0033/cm unapodized in the 7-90/cm spectral interval is described. The spectra from measurements recorded on April 24, 1979 from a balloon-borne platform at about 39 km altitude launched from the National Scientific Balloon Facility of Palestine, TX are presented. The main spectroscopic constituents include a few strong and saturated lines due to the rotational spectrum of water vapor, to magnetic dipole transitions of oxygen, and to the rotational spectrum of ozone. It is shown that the lines of ozone prevent the positive identification of the contribution to the submillimeter spectrum of several minor constituents such as HF, HCl, HCN, HNO3, and N2O. The assignments which are possible in the spectra are revised.

Description: Infrared solar spectra have been obtained during a series of flights with a balloon borne Fourier Transform Spectrometer system. Major emphasis during these flights was placed on obtaining data during sunset. The spectra thus contain information on the atmospheric transmission over long stratospheric paths. These spectra have been analyzed to obtain information on the constituents responsible for the observed absorptions and the distribution with altitude of several of these constituents of interest in stratospheric chemistry. These spectra have also been used to determine the spectroscopic parameters for several compounds such as O3 which are difficult to study in the laboratory. A description of the instrumentation used to obtain the data, samples of the spectra obtained, and details of the analysis are given.

Description: The present cryogenic blackbody reference, or 'cold load', for mm-wavelength radiation has an emissivity of more than 0.99 over a two-octave wavelength range and can be used as a calibrating standard for sensitive IR photometers. The transmittance spectrum obtained indicates that wave impedance and index do not vary significantly over the 80-360 GHz range.

Description: Recent theoretical and observational studies of middle atmosphere electrodynamics are reviewed. Attention is given to observations of large electric fields in the mesosphere and stratosphere which suggest magnitudes of about one volt per sq m. Recommendations are offered with respect to areas of future study, with emphasis on studies of the morphology of large electric fields, and their relationship with external influences such as magnetospheric electric fields and tropospheric thunderstorms.

Description: This paper discusses the measurement and comparison of particle size and velocity measurements in sprays. The general nature of sprays and the development of standard, consistent research sprays are described. The instruments considered in this paper are: pulsed laser photography, holography, television, and cinematography; laser anemometry and interferometry using visibility, peak amplitude, and intensity ratioing; and laser diffraction. Calibration is by graticule, reticle, powders with known size distributions in liquid cells, monosize sprays, and, eventually, standard sprays. Statistical analyses including spatial and temporal long-time averaging as well as high-frequency response time histories with conditional sampling are examined. Previous attempts at comparing instruments, the making of simultaneous or consecutive measurements with similar types and different types of imaging, interferometric, and diffraction instruments are reviewed. A program of calibration and experiments for comparing and assessing different instruments is presented.

Description: The steady state gravity wave model of Schoeberl et al. (1983) is extended to compute wave breaking by disturbances originating at the earth's surface. For winter and summer mean zonal wind profiles, no waves reach the mesosphere unless the absolute value of the zonally averaged perturbed zonal velocity minus c is greater than approximately 20 m/sec. Gravity waves with c = 0 can only reach the winter mesosphere if planetary scale waves are present in the troposphere and the lower stratosphere, to provide strong zonal wind channels for upward wave propagation. This results in nonzonal wave breaking in the mesosphere which could provide in situ forcing of planetary waves. Dissipation of gravity waves by molecular viscosity and conduction can provide significant deceleration and heating/cooling in the 85-105 km region.