ALBERT

Description: The purpose is not to provide a detailed discussion of several wall interference experiments, but rather to use these experiments (recently accomplished in the Boeing Transonic Wind Tunnel (BTWT) to illustrate the problems associated with many of the measurements required by current wall interference assessment/correction (WIAC) procedures. The wall correction to lift is emphasized. It is shown that, because conventional tunnels and relatively small models continue to be used, the flow field or flow boundary measurements to be made impose severe requirements on the experiment itself. In some cases, existing instrumentation and test techniques may not be adequate to obtain the data accuracies needed.

Description: Based upon limited, initial observations of wall interference corrections obtained for one airfoil test, there is a need for assessing the upstream flow direction. If there is no direct measurement then a two-pass correction procedure similar to the one described here is required. Questions have arisen pertaining to the correct interpretation of the pressure coefficients measured on the slats of a slotted tunnel wall, the interpretation of just what the calculated equivalent body encompasses or should include, and what can or should be considered as quantitative criteria for data correctability. Further studies using this modified procedure will address these questions. Hopefully, a meaningful WIAC procedure can be validated for the airfoil tests in the 0.3-m TCT.

Description: A series of airfoils were tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT) at Reynolds numbers from 2 to 50 million. The 0.3-m TCT is equipped with Barnwell slots designed to minimize blockage due to the tunnel flow and ceiling. This design suggests that sidewall corrections for blockage is needed, and that a lifting airfoil produces a change in angle of attack. Sidewall correction methods were developed for subsonic and subsonic-transonic flow. Comparisons of theory with experimental data obtained in the 0.3-m TCT for two airfoils, the British NPL 9510 and the German R-4 are presented. The NPL 9510 was tested as part of the NASA/United Kingdom Joint Aeronautical Program and R-4 was tested as part f the DFVLR/NASA Advanced Airfoil Research Program. For the NPL 9510 airfoil, only those test points that one would anticipate being difficult to predict theoretically are presented.

Description: Representation of the flow around full-scale ships was sought in the subsonic wind tunnels in order to a Hain Reynolds numbers as high as possible. As part of the quest to attain the largest possible Reynolds number, large models with high blockage are used which result in significant wall interference effects. Some experiences with such a high blockage model tested in the NASA Ames 12-foot pressure wind tunnel are summarized. The main results of the experiment relating to wind tunnel wall interference effects are also presented.

Description: The various procedures referred to as wall interference assessment and correction procedures presume the existence of a surface distribution of data (usually static pressure) measured over a surface on or near the tunnel walls for each test point to be assessed. An alternative approach in which a reasonably sophisticated computer model of the test section flow would be fitted parametrically to a sparse set of measured data is presented. The measurements provides line distributions of static pressure near the center lines of the top, side and bottom walls. The development of a test section model incorporating explicit recognition of discrete slots of finite length with controlled flow reentry into the solid wall downstream portion of the tunnel is shown.

Description: A window environmental protection assembly developed for the shuttle infrared leeside temperature experiment is described. The assembly consists of a carbon phenolic composite window mount which contains two silicon windows, a fibrous environmental protection plug to protect the windows during launch operations and ascent heating, a release mechanism used to jettison the plug just prior to atmospheric entry, and two pin puller mechanisms which retain the plug. The plug is released from the window mount assemblies using pneumatic pin pullers and separation springs in the release mechanism. The assembly was designed and tested to withstand the severe mechanical and thermal environments which could be experienced at the top of the shuttle orbiter vertical stabilizer during the ascent, on-orbit, and entry periods of the shuttle trajectory.

Description: Raypaths for decametric wavelength radiation in Jupiter's magnetosphere were calculated. The model-dependent raypaths with the Voyager observations were compared. Characteristics of the source regions and the influence of propagation effects were deduced. A three dimensional ray tracing program was employed to calculate the raypaths. Families of rays were launched at particular angles with respect to the magnetic field lines to generate conical sheets of radiation for various frequencies and various source locations. As the planet's magnetic field rotates, these warped sheets of radiation sweep past the observer, producing signatures in frequency versus time plots. These signatures match some of those found in the Voyager data. The greatest propagation effects occur in and around the source regions in the Io auroral oval.

Description: Altitude data derived from the 12.6 cm radar measurements obtained at JPL's Goldstone Facility were used to explore the utility of this type of regional analysis and to develop criteria for the interpretation of hypsometric data for planets where no visual images are available. Examination of the radar-derived hypsogram for Mars shows that the unimodal distribution of elevations contains several second order peaks and is skewed toward a modal elevation of about 3.5 km above the 6.1 mb datum. Individual topographic features can be recognized from this hypsogram, but such interpretations are based on the known surface morphology that has been determined from spacecraft images. It is not yet known how, for example, cratered terrain, regional slopes or other morphological features could be identified using the hypsogram if no images were available for ground-truth. The role that large impact craters play in influencing the shape of a hypsogram is being studied.

Description: A method for determining the limb darkening planet, acquired in the same wavelength range (lambda), within a few degrees of the same phase angle (alpha), but acquired at different illumination and viewing conditions. The two images are first geometrically registered in simple cylindrical format. A limb darkening factor is computed for each pixel pair and output as a digital image. Systematic trends with photometric coordinates across this image indicate either a calibration error or inappropriateness of the particular photometric function. This method can be used for any photometric function with a single limb darkening factor, such as the Minnaert function or the function which combines the Lommel-Seeliger and Lambert functions. By solving for many pairs of images, the limb darkening factor as a function of alpha and lambda may be determined. The two image limb darkening solutions determined for 1 Voyager image pair on Ganymede, 16 image pairs on Callisto, 44 pairs on Europa, and 19 pairs on Io are discussed.

Description: Near infrared reflectance spectra for the Aristachus region, obtained using the 2.2m UH telescope at the Mauna Kea Observatory, were reduced and analyzed. The spectra obtained for the central peak, southern floor, southwestern wall, eastern wall, and northwestern wall of Aristachus crater exhibit shallow continuum slopes, relatively strong feldspar bands, pyroxene bands stronger than those typically seen in the spectra of fresh higland features, and pyroxene band centers near l micrometer suggesting the dominance of Ca rich clinopyroxene. The spectrum of the south rim of Aristachus is quite distinct from those of other crater units. The position of Aristrchus on the plateau/mare boundary raises questions concerning compositional variations in crater ejects deposits.

Description: The hypothesis that an extraordinary radar smoothness of a lunar target suggests that ground moisture is rest on the assumption that on the penetration-depth scale, the dielectric constant be an isotropic quantity. In other words, the planet's surface should have no vertical structure. Results of modeling exercises (based on the early lunar two-layer models) conducted to simulate the behavior of radar reflectivity, at S-band, over Solis Lacus, without manipulating the dielectric constant of the base layer (i.e., without adding moisture) are summarized. More sophisticated, explicit, rather than iterative multi-layer models involving dust, duricrust, mollisol, and permafrost are under study. It is anticipated that a paradoxical situation will be reached when each improvement in the model introduces additional ambiguities into the data interpretation.

Description: Eight landslide locales were selected in Valles Marineris for preliminary geomorphological mapping. Four main suites of morphological features were identified. In four order outward from the head scarp they are: (1) large ridges in head area, transverse to movement direction, probably slump blocks or pieces of wall that fell or toppled, possibly backward rotated; (2) smaller ridges, convex toward distal edge of slides, many with lobate pattern, some possibly step like scarps rather than ridges; (3) thin, sheet like debris cover, forms discrete fan shaped lobe with edge scarps unconfined; and (4) low transverse, continuous ridges (possibly folds) found at distal edge of slides, where debris appears to have encountered obstructions (e.g., opposing canyon walls), but not all confined slides exhibit this feature. Any one landslide can possess all or some of these features. Slides in the western Valles Marineris are more complex and show more variety than those in the eastern part.

Description: In order to understand better the polygenetic evolution of landforms on the martian surface, field studies were conducted in and around the Kharga Depression, Egypt. The Kharga region, on the eastern edge of Egypt's Western Desert, was subject to erosion under mostly hyperarid climatic conditions, punctuated by brief pluvial episodes of lesser aridity, since early Pleistocene time. The region contains numerous landforms analogous to features on the martian surface: yardangs carved in layered surficial deposits and in bedrock, invasive dune trains, wind-modified channels and interfluves, and depressions bounded by steep scarps. Like many of the topographic depresions on Mars, the Kharga Depression was invaded by crescentic dunes. In Egypt, stratigraphic relations between dunes, yardangs, mass-wasting debris, and wind-eroded flash-flood deposits record shifts in the relative effectiveness of wind, water, and mass-wasting processes as a function of climate change.

Description: Polygonal-fracture patterns on the martian surface were discovered on Viking Orbiter images. The polygons are 2-20 km in diameter, much larger than those of known patterned ground on Earth. New observations show, however, that polygons exist on Mars that have diameters similar to those of ice-wedge polygons on Earth (generally a few meters to more than 100 m). Various explanations for the origin of these crustal features are examined; seasonal desiccation and thermal-contraction cracking in ice-rich ground. It is difficult to ascertain whether the polygons are forming today or are relics from the past. The crispness of some crack suggests a recent origin. On the other hand the absence of upturned edges (indicating actively forming ice wedges), the locally disintegrating ground, and a few possible superposed rayed craters indicate that the polygons are not forming at the present.

Description: Fluvial drainage systems, delineated by mapping on stereo pairs of Viking Orbiter images, have developed in various-sized basins in the Margaritifer Sinus (MC-19) and Agyre (MC-26) Quadrangles, Mars. The Ladon Valles system is the largest, draining into and through two multi-ringed impact basins. Smaller fluvial basins to the southeast of the Ladon structural basin appear to have internal drainage. An intermediate-scale fluvial basin containing Himera Vallis extends along a north-south axis at 22 W and opens northward toward outflow channels south of Margaritifer Chaos. Stereo-pair mapping was extended furhter to the east, in MC-19 Ne, Se, and MC-26 NE, to investigate sources of outflow to the Ares Vallis system. The direction of flow in the channel at the northeast quadrant of the Ladon Basin is unresolved at present because of the poor quality of images available to form stereo pairs. However, an easterly drainage basin boundary running north-south along longitude 9 W, and extending westward at latitude 32-35 S, encloses a series of longitudinal drainage systems. Both the Parana Valles-Loire Vallis system and the Samara Valles system appear to drain in a northwesterly direction. The Samara flows to the Himera drainage basin, and the Parana-Loire to the northeast Ladon channel area.

Description: Particle velocities were determined in environmental wind tunnels capable of simulating aeolian processes on Earth, Mars, and Venus. Comparisons of results for Earth, Mars, and Venus reveal some remarkable differences. Most particles achieve speeds nearly equal to freestream wind speed on Venus, but seldom achieve half the wind speed on Mars; Earth cases are of intermediate values. This is attributed to the differences in atmospheric density and to the threshold wind speeds among the three planetary environments. Particles are more easily moved in the dense venusian atmosphere than on Mars; consequently, threshold speeds are very low, and for the range of wind speeds in which most movement is presumed to occur (just above threshold speeds), the grains need not be moving very fast to achieve 100% of the wind speed. Conversely, particles on Mars must accelerate very rapidly to achieve the speed of the high winds required for threshold, and despite the fact that saltation path lengths are long on Mars, most grains fall to the surface before achieving even 50 to 60% of freestream wind speed.

Description: Recent systematic mapping of Mercury has revealed many ancient and previously unrecognized multiring basins. The population of these basins now stands at 20, possibly is as large as 25, and includes at least 76 measurable rings. From the new data base, we present some systematics of basin ring spacing on Mercury, compare them with similar data for the Moon, and draw some preliminary conclusions on conditions of ring formation for basins on the terrestrial planets.

Description: Maxwell Montes represent the most distinctive topography on the surface of Venus, rising some 11 km above mean planetary radius. The multiple data sets of the Pioneer missing and Earth based radar observations to characterize Maxwell Montes are analyzed. Maxwell Montes is a porkchop shaped feature located at the eastern end of Lakshmi Planum. The main massif trends about North 20 deg West for approximately 1000 km and the narrow handle extends several hundred km West South-West WSW from the north end of the main massif, descending down toward Lakshmi Planum. The main massif is rectilinear and approximately 500 km wide. The southern and northern edges of Maxwell Montes coincide with major topographic boundaries defining the edge of Ishtar Terra.

Description: Many of the questions regarding aeolian processes on Venus and the subsequent implications for surface history involve understanding the physics of particle motion in the venusian environment. The surface environment of Venus is simulated as closely as practicable using the Venus Wind Tunnel and to determine threshold wind speeds, particle flux, particle velocities, and the characteristics of various aeolian bedforms. Despite the relatively low wind speeds on Venus, the flux of windblown material on Venus is potentially high. A high fraction of material is transported as surface creep by rolling, estimates yield rates up to 100 kg per cm lane width per year depending upon the availability of material and wind frequency, suggesting that the formation of lowland plains by aeolian processes and the burial of various landforms such as impact craters could occur on short geological time-scales. Wind tunnel simulations demonstrate that aeolian processes may be very effective in modifying the surface through erosion and deposited and may have an important influence on the composition of the atmosphere.

Description: Caldera-topped volcanoes are the largest volcanic edifices on a planet, and represent relatively long term development of near surface magma chambers. The types, geometries, numbers, and distributions of calderas on the Earth, Mars, Venus, and Io are compared.

Description: Geomorphic mapping revealed that the three volcanic constructs within Elysium Planitia (Hecates Tholus, elysium Mons and Albor Tholus) are very different in their overall morphology and represent three distinct types of martian volcano. Hecates Tholus was found to possess the most likely possible example of a young, explosively generated, air fall deposit, while the volume of magma erupted from Elysium Mons appears to have been orders of magnitude larger than that erupted from Albor Tholus. A primary aim of the regional geological analysis of Elysium Planitia is to further understand the volcanic and tectonic evolution of the area by the identification and interpretation of individual lava flows and their source vents. Lava flow size, spatial distribution, flow direction and the stratigraphic relationships of these lava flows to adjacent structural features were all measured. The topographic form of Elysium Mons has totally controlled the flow direction of lava flows within Elysium Planitia. Lava flows from Elysium Mons can be traced for distances of 150 to 250 km in a radial direction from the volcano. Parasitic vents located beyond the recognizable volcanic construct also conform to this radial pattern. A second unusual characteristic of the Elysium Planitia region is the high frequency of occurrence of sinuous channels that are morphologically similar to lunar sinuous rilles.

Description: The properties of freeze-dried dilute dispersions of dust in water ice are of considerable interest in studies of comet nucleus mantles. The formation of a rind residue produced by the sublimation of water ice containing various amounts of fine clay particles may be an important process. A simulation of the development of the dry dust rind on the surface of comets is presented. This rind is the result of preferential ice sublimation. The development and disruption of this rind and its subsequent levitation by water vapor flow is studied. The most interesting rind simulant is produced by dispersing 0.1 micron particles of montmorillonite in water in concentrations of 10%, 1%, and 0.1%. These dispersions are then sprayed into liquid nitrogen in the form of 100 micron droplets. The frozen droplets are then freeze-dried in a vacuum which prevents the ice temperature from rising above -30 C. Sublimation of the nitrogen and the water produced dry rinds. The most striking result was the development of large cohesive matrices of individual clay particles, and in some cases a continuous cohesive crust. Scanning electron microscope (SEM) observations reveal that the material formed by freeze-drying the 0.1% dispersion does not retain the original spherical shape of the sprayed 100 micron droplets; instead it consists of a continuous filamentary network, as shown in the SEM stereo micrographs.

Description: A model of regolith evolution on bodies subjected to an asymmetric impact flux is presented. The general effect of an asymmetric impact flux is ballistic diffusion of regolith from areas of high impact flux to areas of lower flux. The effect is most pronounced on low gravity bodies where ejecta travel distances are large, and on bodies with strong flux asymmetries. It may be especially important on Iapetus, where retrograde debris from Phoebe striking the leading hemisphere may produce a flux asymmetry as large as 100 to 1 from apex to antapex. We find that the net amount of material transported by ballistic diffusion is inversely proportional to satellite density. Theoretical calculations and Voyager observations support the view that tidal heating is sufficient to maintain a liquid layer throughout the history of Europa. Photosynthetic, thermal, electrical, and chemical energy sources are considered. The calculations suggest that there may be regions on Europa, very limited in space and time, with physical conditions that are within the range of adaptation of life on Earth. Calculations for the electrical currents within Europa for a thick ice crust are very small.

Description: As part of the Galilean Satellites Mappers Program, the South Polar region of Io was studied. Examination of the Voyager images had led to reassessment of the possible mechanisms by which certain units were created or modified in this area. Specifically, analyses have focused on determining the relative age of the mountain material and on the process by which the layered plains material was eroded.

Description: Four morphologically distinct major volcanic forms occur within and adjacent to the Kane Patera, high resolution map quadrangle Ji2B (lat 15 to 50 S., long 355 to 20 W.). Volcanic vents and flows from four types of features are included: low-relief shield volcanoes, domical shield volcanoes, large calderas and isolated groups of flows not obviously associated with a central vent.

Description: Airborne Imaging Spectrometer (AIS) data were collected 30 August 1985 from a desert shrub community in central Oregon. Spectra from artificial targets placed on the test site and from bare soil, big sagebrush (Artemesia tridentata wyomingensis), silver sagebrush (Artemesia cana bolander), and exposed volcanic rocks were studied. Spectral data from grating position 3 (tree mode) were selected from 25 ground positions for analysis by Principal Factor Analysis (PFA). In this grating position, as many as six factors were identified as significant in contributing to spectral structure. Channels 74 through 84 (tree mode) best characterized between-class differences. Other channels were identified as nondiscriminating and as associated with such errors as excessive atmospheric absorption and grating positin changes. The test site was relatively simple with the two species (A. tridentata and A. cana) representing nearly 95% of biomass and with only two mineral backgrounds, a montmorillonitic soil and volcanic rocks. If, as in this study, six factors of spectral structure can be extracted from a single grating position from data acquired over a simple vegetation community, then AIS data must be considered rich in information-gathering potential.

Description: Airborne Imaging Spectrometer (AIS) data were acquired over an area of freshwater wetlands in Central California on September 23, 1985. Plant samples were subsequently collected along the flight line with the goal of relating plant tissue chemistry to spectral reflectance in the near-infrared region. It was determined that a consistent relationship existed between spectral response and plant tissue chemistry. This was especially evident in the 1500 to 1700 nm region.

Description: Airborne Imaging Spectrometer (AIS) data were acquired in 1985 over the Bonanza Creek Experimental Forest, Alaska for the analysis of canopy characteristics including biochemistry. Concurrent with AIS overflights, foliage from fifteen coniferous and deciduous forest stands were analyzed for a variety of biochemical constituents including nitrogen, lignin, protein, and chlorophyll. Preliminary analysis of AIS spectra indicates that the wavelength region between 1450 to 1800 namometers (nm) displays distinct differences in spectral response for some of the forest stands. A flat field subtraction (forest stand spectra - flat field spectra) of the AIS spectra assisted in the interpretation of features of the spectra that are related to biology.

Description: Airborne Imaging Spectrometer (AIS) data were collected over the fossil hot spring deposit at Ivanhoe, Nevada in order to determine the surface distribution of NH4-bearing minerals. Laboratory studies show that NH4-bearing minerals have characteristic absorption features in the near-infrared (NIR). Ammonium-bearing feldspars and alunites were observed at the surface of Ivanhoe using a hand-held radiometer. However, first look analysis of the AIS images showed that the line was about 500 m east of its intended mark, and the vegetation cover was sufficiently dense to inhibit preliminary attempts at making relative reflectance images for detection of ammonium minerals.

Description: The Airborne Imaging Spectrometer (AIS) was flown over granitic, volcanic, and calc-silicate terrain around the Mary Kathleen Uranium Mine in Queensland, in a test of its mineralocial mapping capabilities. An analysis strategy and restoration and enhancement techniques were developed to process the 128 band AIS data. A preliminary analysis of one of three AIS flight lines shows that the data contains considerable spectral variation but that it is also contaminated by second-order leakage of radiation from the near-infrared region. This makes the recognition of expected spectral absorption shapes very difficult. The effect appears worst in terrains containing considerable vegetation. Techniques that try to predict this supplementary radiation coupled with the log residual analytical technique show that expected mineral absorption spectra can be derived. The techniques suggest that with additional refinement correction procedures, the Australian AIS data may be revised. Application of the log residual analysis method has proved very successful on the cuprite, Nevada data set, and for highlighting the alunite, linite, and SiOH mineralogy.

Description: The Singatse Range is composed of a series of 53 types of volcanic, plutonic, metamorphic, and sedimentary rocks. In addition the Jurassic plutonic rocks are also of economic interest for their copper mineralization which is contained in a porphyry dike swarm. The 1984 and 1985 flight results from the Airborne Imaging Spectrometer (AIS) instrument flown in the NASA/JPL C-130 aircraft are contrasted and compared. The 1984 data are less noisy than the 1985, in which many sets of vertical stripings from bad detectors can be seen. Significantly however, enough of the hydrothermal alteration patterns can be seen in each line at the mutual crossing points that one can say that the specific targets were detected in both year's flights. The spectra of both years are corrupted by the second-order effect from the grating, but 0-H bond absorption at essentially correct wavelengths for sericite and/or kaolinite can be seen.

Description: The surface mineralogy in and around Moses Rock diatreme, a kimberlite-bearing dike in SW Utah, was examined using internally calibrated Airborne Imaging Spectrometer (AIS) data. Distinct near-infrared absorption characteristics of clays, gypsum, and serpentine (a key marker for kinberlite concentration) allowed the surface units containing these components to be identified spatially and the relative abundance of each component measured. Within the dike itself, channels and dispersed components of kimberlite and blocks of country rocks were accurately determined.

Description: Analysis of Airborne Imaging Spectrometer (AIS) data acquired in Australia has revealed a number of operational problems. Horizontal striping in AIS imagery and spectral distortions due to order overlap were investigated. Horizontal striping, caused by grating position errors can be removed with little or no effect on spectral details. Order overlap remains a problem that seriously compromises identification of subtle mineral absorption features within AIS spectra. A spectrometric model of the AIS was developed to assist in identifying spurious spectral features, and will be used in efforts to restore the spectral integrity of the data.

Description: The Voyager 1 and Voyager 2 narrow angle cameras have been imaging Uranus and Neptune (through several filters) from distances of several AU for the past four years. The justification for this is to determine the way in which the albedoes of the two planets vary with angle from the sun. The Voyager 1 spacecraft has already reached a phase angle of approx. 40 deg. for Neptune and approx. 70 deg. for Uranus. The albedo of a gaseous planet depends on the phase angle (angle from the sun through the planet to the observer), the color being observed, and the vertical distribution and nature of aerosols and clouds in the atmosphere of the planet. Since the colors are known and the phase angles, and phase curves will be used to constrain models of the aerosol and cloud structrures of Uranus and Neptune. A knowledge of the way albedo varies with phase angle allows one to compute the total amount of sunlight being absorbed by a planet. With knowledge of the solar flux incident on the planet and knowledge of how much infrared is being emitted by the planet (at least in the direction of the Earth and sun) one can determine a rough extimate of the internal heat source of the planet. Although Jupiter and Saturn have measured internal heat sources of magnitude comparable to their absorbed energy from the sun, preliminary results indicate that Uranus may not have an internal heat and that Neptune if it has one that heat source is small.

Description: Narrowband CCD profiles of C2 and grains in several comets (including P/Halley and P/Giacobini-Zinner) were performed. Rotational light curves were made of Comet P/Arend-Rigaux (visible and infrared) yielding the size, shape, albedo, and rotation period of the nucleus. Production rates were measured as a function of heliocentric distance for OH, CN, and C2 in P/Giacobini-Zinner and for OH, NH, CN, C3, and C2 in P/Halley. Detection and measurement was made of forbidden (O I) lines near 6300 and 5577 A in P/Halley, permitting the production rate of oxygen from CO to be distinguished from that from H2O. Identification of C-12C-13 lines in cometary spectra indicating a possible enrichment of C-13 over the telluric value was made. An assessment of techniques for detecting (determining the existence of) a trans-Neptunian comet belt is included.

Description: The Voyager data in a newly produced noise-reduced and recalibrated format has been received. New color spectrograms were developed on high resolution color terminals which display this data. The production of these new spectrograms utilizing the new format data is quite important, because it eliminates a serious problem of noise contamination and miscalibration in the old data set. In addition, a new Jovian plasma model was introduced, which includes the Io torus and accounts for 7 ionic species. The new plasma model is important in the ray tracing of hectometric (HOM) and kilometric (KOM) radiation which may be influenced by the Io torus.

Description: A multi-color, broad-band photographic program for monitoring atmospheric variability of Jupiter and Saturn with the 61-cm, f/75 telescope was continued. The archivial product consists of approximately 20 sequential images on 3 1/4 x 4 1/4 glass plates with a plate scale of 4.53 arc sec/mm. An eleven-step sensitometric wedge, recorded times of acquisition, and fiducial marks which determine the orientation of the plate, are recorded on each individual plate. This allows accurate positional measurements, as well as detailed relative surface brightness determinations. Detailed measurements of the Red Spot are being utilized in a study of zonal velocity variation and the ability to predict the longitude of the Red Spot during the Galileo mission. An ongoing 5-color series of Saturn has been maintained to map the seasonal changes in the belt-zone reflectivity. Digitization of a series of blue images containing the Red Spot and a series of red and blue images excluding the Red Spot are being processed and reduced to normalized surface brightness maps. This data is being utilized to map time-dependent brightness variations of selected features, belts, and ones.

Description: The interior structure of the Jovian planets was studied by means of observational data obtained by ground-based astronomy. Recent work was oriented toward a determination of oblateness from occultation measurements of the shape of planetary atmospheres. This provides a determination of the degree of central condensation of the planet, which is then compared with interior models and theoretical equations of state. As a serendipitous result of the attempts to measure the oblateness of Neptune, a partial Neptune ring (or arc) was discovered following an occultation observation on July 22, 1984. During 1985, older observations were reexamined to determine whether Neptune arcs had been detected (but not identified) during previous occultations. It appears that Neptunian arcs may locally imitate Uranian rings, with an 1981 event resembling Uranus' epsilon ring, while an 1984 event was more similar to the thinner Uranian rings such as the alpha ring.

Description: This program supports NASA's deep space exploration missions, particularly those to the outer Solar System, and also NASA's Earth-orbital astronomy missions, using ground-based observations, primarily with the NASA IRTF at Mauna Kea, Hawaii, and also with such instruments as the Kitt Peak 4 meter Mayall telescope and the NRAO VLA facility in Socorro, New Mexico. An important component of the program is the physical interpretation of the observations. There were two major scientific discoveries resulting from 8 micrometer observations of Jupiter. The first is that at that wavelength there are two spots, one near each magnetic pole, which are typically the brightest and therefore warmest places on the planet. The effect is clearly due to precipitating high energy magnetospheric particles. A second ground-based discovery is that in 1985, Jupiter exhibited low latitude (+ or - 18 deg.) stratospheric wave structure.

Description: The purpose is to describe work that is being done to find theoretical models to describe radar backscatter from vegetation layers. The geometry of the problem is shown. The information that one would like to find through the application of the results of these models would include: the thickness of the layer; the absorption in the layer (i.e., density, moisture content, and biomass); the geometry of the scatterers (i.e., shape and orientation); how much of the received power is due to volume scattering only; and a way to enhance the ratio of scattering that has some interaction with the ground surface. The proposed ways to find this information are discussed.

Description: This study was conducted as a part of the research tasks under the Radar Land Cover Analysis Program. The Radar Land Cover Analysis objective is, through utilization of multisensor data, to gain a basic understanding of the measurements and data characteristics in the visible-IR-microwave regions of the electromagnetic spectrum associated with specific surface features and cover types. Since the results of analysis of data acquired by Shuttle Imaging Radar (SIR-A) and LANDSAT Thematic Mapper (TM) over the study area were reported (NSTL/ERL Report No. 228, December 1984), this study focused on the analysis and evaluation of the L-band multipolarization airborne SAR data acquired over a southeastern pine forest scene. The data acquisition mission was flown on September 8 and 9, 1983. The HH, HV polarizations and the VV, VH polarizations were used on the first and the second day, respectively. Due to instrumentation difficulties, the digital recorder recorded only the second day's data. Because of this, only the VV and VH polarization data were used in this analysis. However, the HH and HV polarization images were available for visual comparison. It appears that SAR digital numbers correlate with the index of green biomass.

Description: Wall interference is made predominant in tunnel models and by wall geometries to facilitate the study of slot flow. The viscous effects in slots are studied by two dimensional measurements of flow. Wall interference is assessed by measuring pressure distributions at two levels near the walls. Interference on lifting delta wings is calculated. Pressure distributions at inner boundaries show basis axisymetries between the pressure side and the suction side, pointing to the necessity of having wider slots on the pressure side.

Description: Classical methods for calculation of wall corrections which are not satisfactory for a number of flows of interest are discussed. To meet these objections, a number of methods were developed which use measurements of the low at or close to the tunnel walls as an outer boundary condition to define wall interference. The development, assessment and application of one such method is summarized.

Description: Measured field data as a boundary condition for calculating the interference flow field were applied. They are divided into two categories. In the first category, the field data must consist of distributions of a single velocity component, and an accurate estimate of the hypothetical free air contribution of the model to this component is required. The differences between measured values and estimated model contributions are attributed to wall interference and they establish the boundary condition. The associated field data measurements are simple, yet the necessary model representation generally is a serious drawback. The second category requires field data which consist of velocity vector distributions at the price of multicomponent measurements, but at the profit that no information at all is required about the model. In solid wall test sections, the price is reduced to virtually zero but the profit remains.

Description: A limited-zone ventilated wall panel was developed for a closed-wall icing tunnel which permitted correct simulation of transonic flow over model rotor airfoil sections with and without ice accretions. Candidate porous panels were tested in the Ohio State University 6- x 12-inch transonic airfoil tunnel and result in essentially interference-free flow, as evidenced by pressure distributions over a NACA 0012 airfoil for Mach numbers up to 0.75. Application to the NRC 12- x 12-inch icing tunnel showed a similar result, which allowed proper transonic flow simulation in that tunnel over its full speed range.

Description: The free-stream interference caused by the flow through the slotted walls of the test sections of transonic wind tunnels has continuously a problem in transonic tunnel testing. The adaptive-wall transonic tunnel is designed to actively control the near-wall boundary conditions by sucking or blowing through the wall. In order to make the adaptive-wall concept work, parameters for computational boundary conditions must be known. These parameters must be measured with sufficient accuracy to allow numerical convergence of the flow field computations and must be measured in an inviscid region away from the model that is placed inside the wind tunnel. The near-wall flow field was mapped in detail using a five-port cone probe that was traversed in a plane transverse to the free-stream flow. The initial experiments were made using a single slot and recent measurements used multiple slots, all with the tunnel empty. The projection of the flow field velocity vectors on the transverse plane revealed the presence of a vortex-like flow with vorticity in the free stream. The current research involves the measurement of the flow field above a multislotted system with segmented plenums behind it, in which the flow is controlled through several plenums simultaneously. This system would be used to control a three-dimensional flow field.

Description: A three-dimensional adaptive-wall wind tunnel experiment was conducted at Ames Research Center. This experiment demonstrated the effects of wall interference on the upwash distribution on an imaginary surface surrounding a lifting wing. This presentation demonstrates how the interference assessment procedure used in the adaptive-wall experiments to determine the wall adjustments can be used to separately assess lift- and blockage-induced wall interference in a passive-wall wind tunnel. The effects of lift interference on the upwash distribution and on the model lift coefficient are interpreted by a simple horseshoe vortex analysis.

Description: A wall interference correction method for closed rectangular test sections was developed which uses measured wall pressures. Measurements with circular discs for blockage and a rectangular wing as a lift generator in a square closed test section validate this method. These measurements are intended to be a basis of comparison for measurements in the same tunnel using ventilated (in these case, slotted) walls. Using the vortex lattice method and homogeneous boundary conditions, calculations were performed which show sufficiently high pressure levels at the walls for correction purposes in test sections with porous walls. In Gottingen, an adaptive test section (which is a deformable rubber tube of 800 mm diameter) was built and a computer program was developed which is able to find the necessary wall adaptation for interference-free measurements in a single step. To check the program prior to the first run, the vortex lattice method was used to calculate wall pressure distributions in the nonadapted test section as input data for the one-step method. Comparison of the pressure distribution in the adapted test section with free-flight data shows nearly perfect agreement. An extension of the computer program can be made to evaluate the remaining interference corrections.

Description: The following areas were addressed: interchangeable test sections in the 0.3-M Transonic Cryogenic Tunnel (TCT); typical airfoil installation; airfoil capability; advanced technology airfoil test (ATAT); effects of the Reynolds number on the normal force coefficient; effects of the Reynolds number on the drag coefficient; and comparison of experimental results with theory.

Description: A formula for the determination of equivalent model geometry with two variables measured at the interface is derived, based on two dimensional subsonic flow. This predicted model profile is a reasonable initial estimate for transonic flow as long as the sonic region does not reach the interface. A general formula is given in two forms. One is in terms of complex variable functions and the other is an integral equation. The complex-function formula has the advantage of using analytic expressions. The integral equation form requires a numerical solution after assuming the model geometry as a polynomial function. Examples are given to illustrate the application of the formulas.

Description: LANDSAT data acquired over an agricultural area along with ground enumeration of the same area are used to obtain crop acreage estimates which are better (as measured in terms of bias and variance) than can be obtained from either data source alone. Two basic approaches considered within the AgRISTARS program are a stratified crop acreage estimator and a regression estimator. A statement of the problem was mathematically formulated and some theorems were proved which relate to the variance of the two estimators. For a particular set of data, the regression and stratified estimators are compared in terms of certain easily computed parameters.

Description: The two body problem was analyzed with a specific drag model. The model treats drag as a force proportional to the vector velocity and inversely proportional to the distance to the center of attraction. The solution is expressed in terms of known functions and is of a simple and compact form. The time of flight is expressed as a quadrature in the true anomaly. The results are: (1) development of a vector differential equation which allows analysis of an infinite number of gravitational and drag models; and (2) obtaining the solution of a linear differential equation using the inverse method of laplace transforms.

Description: The ratio and flat field photoclinometric methods for determining crater form topography are described. Both methods compensate for the effects of atmospheric scattering by subtracting a haze value from all brightness values. Algorithms were altered to derive relative topographic data for irregular features such as ejecta blankets, lava flows, graben and ridge scarps, dune forms, and stratified materials. After the elevations along the profiles are obtained by integration of the photometric function, a matrix transformation is applied to the image coordinates of each pixel within each profile, utilizing each pixel's integral height, to produce a projection of each profile line onto the surface. Pixel brightness values are then resampled along the projected track of each profile to determine a more correct height value for each pixel. Precision of the methods is discussed.

Description: Viking 1 imagery of the Coprates NW quadrangle was used in an attempt to develop a geomorphic classification scheme for the canyon walls of Valles Marineris analogous to that devised to evaluate the relative tectonic activity of terrestrial mountain fronts. The four classes of walls established are described and mapped. Regions where a class cannot be assigned owing to the presence of intra canyon sediments, landslides, or landslide debris; and apparent fault scarps that occur on the canyon floor rather than at the wall base are also shown. The most striking feature is the concentration of active tectonic features within lus Chasma, and to a lesser extent in Tithonium Chasma, as well as along the north walls of Coprates and East Candor.

Description: The geomorphology of Denmark is dominated by glacial deposits, including both end moraines and ground moraines. Many of these features have morphologies similar to features observed on Mars. A characteristic landscape complex in Denmark is a series of irregular mounds or parallel curvilinear ridges that outline the former ice margin. Many of these resemble curviliner features on Mars, and the Danish landforms occur at a similar scale. Another distinctive landform in Denmark is the hummocky moraine landscape found in parts of Sjaelland. Although their size is smaller, these areas resemble the hummocky terrain associated with some of the curvilinear features in the northern plains of Mars. The hummocky Danish terrain is probably caused by the melting of masses of dead ice left during glacial retreat. Similar landscapes observed developing during retreat of smaller glaciers were ice caps in Scandinavian mountains and in Greenland.

Description: Sand bars and islands within braided rivers have characteristic rhomboid or diamond shapes, often becoming very complex in form as the density of islands increases. Similar forms are observed in the martian outflow channels where the islands occur in groups. This contrasts with the more isolated martian islands which have airfoil shapes, as do isolated streamlined islands in rivers and in the Channeled Scabland. These observations indicate that the bar and island forms are controlled by the density of the islands, with increasing island interaction and flow modification as the density increases. As a continuation of previous flume experiments on the shapes of isolated islands, a new series of experiments investigate the modifications produced by a progressive increase in island density, finally leading to a true braided system.

Description: The properties of freeze dried dilute dispersions of dust in water are of considerable interest in studies of sedimentary processes in the polar regions of Mars. The formation of a rind residue due to the sublimation of water ice containing various amounts of clay may be an important step in these processes. Such phenomena may occur as the result of seasonal or long term (climatic) sublimation of dirty ice caps on Mars. The development and disruption of dust residues on the surface of ice dust mixtures as a result of preferential ice sublimation were simulated in the laboratory. The characteristics of the resulting particles are described and a scenario for the formation of a Martian circumpolar dune field is suggested.

Description: During the first Viking year, two global dust storms occurred and they contributed about 90% of the dust suspended in the Martian atmosphere on a global average, over the course of this year. The remainder was due to the cumulative effect of local dust storms. When globally distributed, the amount of suspended dust introduced into the atmosphere this Martian year was about 5x10(-3) g/sq cm. This mass loading was derived from the incremental optical depths measured over this year and estimates of the mean size of the dust particles (2.5 microns). During the second Martian year, global dust storms were far more muted than during the first year. No near perihelion dust storm occurred, and a somewhat weaker dust storm may have occurred near the start of the spring season in the Southern Hemisphere, at about the same time that the first global dust storm of the first year occurred. Thus, the dust loading derived for the first Martian year may be somewhat higher than the average over many Martian years, a conclusion that appears to be supported by preliminary studies of Martian years beyond the second Viking year on Mars.

Description: Among the major problems of martian geologic history are the cause of the highland-lowland dichotomy, and of the scarp separating these two global-scale provinces. These features were formed after much of the early bombardment was completed; consequently, many of the surviving impact basins very likely were present during the creation of the dichotomy, and it is possible that differences in their present morphologies as a function of location and of relative age may provide clues to the tectonic and geomorphic processes responsible for the dichotomy and the scarp.

Description: Partially and completely buried craters on planetary surfaces are used as probes to determine the thickness and extent of the overlying material as well as the composition of underlying terrain units. Rims of craters protruding through mare basalts on the Moon have been used extensively by DeHon (1977, 1979) to develop isopach maps of both the circular and irregular maria. Such estimates are possible because of Apollo topographic data and the extensive coverage by Lunar Orbiter photographs at various sun angles. On planetary surfaces without such data, however, shadow measurements can only be made by pixel listings with appropriate assumptions concerning support data. In addition, high resolution geochemical data is not available to determine whether the exposed crater rim is composed of material dissimilar from the lavas. Because of the need for lava thickness data, flooding of lunar mare and highland craters was simulated in order to determine empirical relationships between dimensions observed in orbital images and the thickness of the lava.

Description: A classification database using the reflectivity (derived from the altimetry data), rms slope, and the first principal component of altimetry and topographic slope is presented. The resultant clustered data is examined qualitatively as well as quantitatively, to establish the statistical integrity of each cluster by use of an interactive, ternary plotting algorithm. This algorithm plots, for a cluster, the position of each of its pixels within a ternary diagram whose apices represent reflectivity, rms slope, and the first principal component. The digital values in these three databases are normalized such that unity is represented by a value of 255 in each database. The frequencies of each plotted point within the ternary diagram are recorded in order to establish the mode of each cluster. The pixels of each cluster are displayed as one separate color; their ternary plot will show not only the interrelations between clusters, but also the presence of any anomalous points within a cluster. Existing lunar and terrestrial analog radar data is used to establish fields within this ternary diagram that are indicative of as many different geologic materials and tectonics settings as possible. The resultant fields are used to determine empirically the geologic significance of the clusters resulting from the cluster analysis.

Description: The Planet-Crossing Asteroid Survey (PCAS) is making steady progress toward the accumulation of the data required to make improved estimates of the populations and cratering rates which can be compared with the existing record of impact events. The PCAS is the chief source of new objects on which to base these calculations over the past decade, and is an integral part of the continuing refinement of the estimates used in planetological applications. An adjunct effort to determine albedo statistics from photometry of UCAS plates is being pursued as well, to better define the magnitude frequency distributions of asteroids. This will improve the quality of the population and collision probability calculations. The survey effort continues to discover new asteroids whose orbital characteristics may reveal the origin and evolution mechanisms reponsible for the transport of the planet-crossing asteroids to the inner solar system.

Description: Spectral characteristics of semi-arid shrub communities were examined using Airborne Imaging Spectrometer (AIS) data collected in the tree mode on 23 May 1985. Mesic sites with relatively high vegetation density and distinct zonation patterns exhibited greater spectral signature variations than sites with more xeric shrub communities. Spectral signature patterns were not directly related to vegetation density or physiognomy, although spatial maps derived from an 8-channel maximum likelihood classification were supported by photo-interpreted surface features. In AIS data, the principal detected effect of shrub vegetation on the alluvial fans is to lower reflectance across the spectrum. These results are similar to those reported during a period of minimal physiological activity in autumn, indicating that shadows cast by vegetation canopies are an important element of soil-vegetation interaction under conditions of relatively low canopy cover.

Description: Airborne Imaging Spectrometer (AIS) data were acquired for several vegetation types within the humid temperate eastern United States. The spectral region covered, 0.9 to 2.1 microns, was little used in vegetation studies. A preliminary analysis of spectral curves suggests that variations between vegetation spectra may be useful for discriminating plant communities. Calibration and normalization procedures must be refined to compensate for cloud cover, detector and other system noise, and possible second-order effects.

Description: Spectral reflectance properties of deciduous oak-hickory forests covering the eastern half of the Rolla Quadrangle were examined using Thematic Mapper (TM) data acquired in August and December, 1982 and Airborne Imaging Spectrometer (AIS) data acquired in August, 1985. For the TM data distinctly high relative reflectance values (greater than 0.3) in the near infrared (Band 4, 0.73 to 0.94 micrometers) correspond to regions characterized by xeric (dry) forests that overlie soils with low water retention capacities. These soils are derived primarily from rhyolites. More mesic forests characterized by lower TM band 4 relative reflectances are associated with soils of higher retention capacities derived predominately from non-cherty carbonates. The major factors affecting canopy reflectance appear to be the leaf area index (LAI) and leaf optical properties. The Suits canopy reflectance model predicts the relative reflectance values for the xeric canopies. The mesic canopy reflectance is less well matched and incorporation of canopy shadowing caused by the irregular nature of the mesic canopy may be necessary. Preliminary examination of high spectral resolution AIS data acquired in August of 1985 reveals no more information than found in the broad band TM data.

Description: Techniques using Munsell color transformations were developed for reducing 128 channels (or less) of Airborne Imaging Spectrometer (AIS) data to a single color-composite-image suitable for both visual interpretation and digital analysis. Using AIS data acquired in 1984 and 1985, limestone and dolomite roof pendants and sericite-illite and other clay minerals related to alteration were mapped in a quartz monzonite stock in the northern Grapevine Mountains of California and Nevada. Field studies and laboratory spectral measurements verify the mineralogical distributions mapped from the AIS data.

Description: Airborne Imaging Spectrometer (AIS) data, field and laboratory spectra and samples for X-ray diffraction analysis were collected in argillically altered Tertiary volcanic rocks in the Hot Creek Range, Nevada. From laboratory and field spectral measurements in the 2.0 to 2.4 micron range and using a spectroradiometer with a 4 nm sampling interval, the absorption band centers for kaolinite were loacted at 2.172 and 2.215 microns, for montmorillonite at 2.214 micron and for illite at 2.205. Based on these values and the criteria for resolution and separtion of spectral features, a spectral sampling interval of less than 4 nm is necessary to separate the clays. With an AIS spectral sampling interval of 9.3 nm, a spectral matching algorithm is more effective for separating kaolinite, montmorillonite, ad illite in Hot Creek Range than using the location of absorption minima alone.

Description: Airborne Imaging Spectrometer (AIS) data were collected over Virginia City, Nevada; an area of gold and silver mineralization with extensive surface exposures of altered volcanic rocks. The data were corrected for atmospheric effects by a flat-field method, and compared to library spectra of various alteration minerals using a spectral analysis program SPAM. Areas of strong clay alteration were identified on the AIS images that were mapped as kaolinitic, illitic, and sericitic alterations zones. Kaolinitic alteration is distinguishable in the 2.1 to 2.4 and 1.2 to 1.5 micrometer wavelength regions. Montmorillonite, illite, and sericite have absorption features similar to each other at 2.2 micrometer wavelength. Montnorillonite and illite also may be present in varying proportions within one Ground Instantaneous Field of View (GIFOV). In general AIS data is useful in identifying alteration zones that are associated with or lie above precious metal mineralization at Virginia City.

Description: Airborne Imaging Spectrometers (AIS) data collected in 1984 and 1985 showed pronounced striping in the vertical and horizontal directions. This striping reduced the signal to noise ratio so that features of the spectra of forest canopies were obscured or altered by noise. This noise was removed by application of a notch filter to the Fourier transform of the imagery in each waveband.

Description: Selective absorption of electromagnetic radiation by atmospheric gases and water vapor is an accepted fact in terrestrial remote sensing. Until recently, only a general knowledge of atmospheric effects was required for analysis of remote sensing data; however, with the advent of high spectral resolution imaging devices, detailed knowledge of atmospheric absorption bands has become increasingly important for accurate analysis. Detailed study of high spectral resolution aircraft data at the U.S. Geological Survey has disclosed narrow absorption features centered at approximately 2.17 and 2.20 micrometers not caused by surface mineralogy. Published atmospheric transmission spectra and atmospheric spectra derived using the LOWTRAN-5 computer model indicate that these absorption features are probably water vapor. Spectral modeling indicates that the effects of atmospheric absorption in this region are most pronounced in spectrally flat materials with only weak absorption bands. Without correction and detailed knowledge of the atmospheric effects, accurate mapping of surface mineralogy (particularly at low mineral concentrations) is not possible.

Description: The research effort was concentrated toward comet P/Halley, although observations of other comets including Giacobini-Zinner, Hartley-Good and Thiele were made as opportunities arise. In preparing for the apparition of P/Halley, detailed predictions for the emission in the 18 cm OH transitions were made in order to assist observers and to indicate what type of data would be particularly valuable. Likewise, since occultations by the comet of background radio sources can provide unique types of information, the tracks of P/Halley and P/Giacobini-Zinner were surveyed with the NRAO Very Large Array, background sources were mapped, and a catalogue of occulted sources published. Beginning in September, 1985, regular observations of the 18 cm OH lines have been made for P/Halley using the 43 m antenna of the NRAO in Greenbank, West Virginia. These data promise to provide the most accurate time sequence for the OH emission for any comet ever obtained at radio wavelengths. From the linewidth and shape, information is obtained on the kinetics of the gas in the cometary coma. An extensive series of observations have been undertaken with 14 m antenna to study emission from the HCN molecule in P/Halley. These data provide the first definitive detection of this component of the cometary ices. Interesting variations in the production of HCN were observed with time scales less than a day. Likewise, there appeared to be variations in the ratio of the hyperfine components of the J = 1-0 transition.

Description: The first field test of NASA's Global Positioning System (GPS) Geodetic Program took place in March of 1985. The principal objective of this test was the demonstration of the feasibility of the fiducial station approach to precise GPS-based geodesy and orbit determination. Other objectives included an assessment of the performance of the several GPS receiver types involved in these field tests and the testing of the GIPSY software for GPS data analysis. In this article, the GIPSY (GPS Inferred Positioning System) software system is described and baseline solutions are examined for consistency with independent measurements made using very long baseline interferometry.

Description: Work completed on Apollo 14 basalts has been published. The two dates obtained from these rocks comprised the oldest and two of the three oldest ages (4.1 and 4.3 billion years) known for lunar maria basalts; thus their ages are important in understanding the moon's earliest history. Owing to the antiquity of these rocks, two more fragments have been dated as part of a second ASEE/NASA SFF program. The new ages are 3.95 and 4.12 billion years, thus further establishing and amplifying the earlier results. This work, although perhaps more interesting for its chronologic information, was begun as a test of chemical and petrographic models. Fragments of Apollo basalt were placed into five categories, based on petrologic and chemical, especially rare-earth element, composition. Isotopic studies were begun in an attempt to determine if the five groups of basalts were related by age or initial isotopic composition (isotopic composition of lava at time of extrusion). Although a few of the representatives of the five groups have the same age and/or initial strontium-isotopic composition, within the analtytical uncertainties, most apparently are unrelated. Petrologic implications of these data will be published in an appropriate journal.

Description: One aspect of the study of Titan's atmosphere is the elucidation of the chemical and physical nature of the aerosols. In order to facilitate this, a program to produce laboratory synthesized model materials for Titan's aerosol and to study their chemical and physical properties is now in progress. Various processes, including electric discharge, photolysis by ultraviolet light, and irradiation by energetic particles, will be used to produce the materials. A first set of experiments where a nominal Titan mixture (97%N2, 3% CH4, 0.2% H2) was subjected to pulsed high temperature shocks yielded a reddish brown waxy solid. This material was subjected to pyrolysis/gas chromatography, a technique that has been proposed as a method for analysis of the Titan aerosols. Preliminary results show the material to consist of simple hydrocarbons but little else, at least up to temperatures of 600 C. Since the material was colored, compounds other than those mentioned above must be present.

Description: The production of high-resolution topographic maps derived from interferometric synthetic aperture radar observations of the Earth is reported. Topographic maps are typically determined from stereo-pair optical photographs. Vertical relief causes the same terrain to appear in a slightly different projection for differing look angles, and this shift in appearance is interpreted in terms of the height of the terrain. The radar interferometric approach is related to the stereo technique in that the terrain is viewed at two different angles; however, in this case, the angular separation of the antennas is extremely small, on the order of a milliradian or less, as compared to tens of degrees for the optical case. Thus, the geometrical distortion and subsequent rectification correction algorithms are much less severe in the reduction of interferometric data.

Description: Wall interference correction procedures seek to determine the required changes in certain flow or geometric parameters so that the difference between the flow properties at the model's surface in the tunnel and free air are minimized. A transonic and a linear correction procedure were developed for aircraft models. In addition to Mach number and angle of attack corrections, an estimate of the accuracy of the corrections is provided by the transonic correction procedure. Lift, pitching moment and pressure measurements near the tunnel walls are required. The efficiency and accuracy of the correction procedure are improved. Moreover, correction of both the wing and tail angles of attack is allowed. The procedure is valid for transonic as well as subcritical flows. However, for subcritical flows further approximations and simplifying assumptions are made, leading to a very simple and efficient correction procedure.

Description: A facet of a unified tunnel correction scheme which uses wall pressures to determine tunnel induced blockage and upwash is described. With this method, there is usually no need to use data concerning model forces or power settings to find the interference; it follows directly from the pressures and tunnel dimensions. However, highly inclined jets do not produce good pressure signatures and are highly three dimensional, so they must be treated differently. Flow modeling is also discussed.

Description: Wall corrections as a function of wall porosity in the transonic wall interference problem was assessed. Effective porosities primarily for the two dimensional case were established as follows: (1) comparison of experimental data for two geometrically similar models of different chord/height ratio, an overall value of wall porosity could be deduced; (2) theoretical development which allows for unequal porosity for the floor and ceiling and wall boundary pressure measurements, porosities for floor and ceiling could be deduced; (3) a scheme was developed which allowed unequal porosity of floor and ceiling and streamwise varying porosity. The boundary layer development along the perforated floor and ceiling under the influence of the model pressure field, variations in boundary layer thickness underlining the difficulties in deducing meaningful values of wall porosity were determined. Wall boundary pressure measurement, in combination with singularity modelling of the airfoil, was sufficient to yield required information on the wall interference flow without having to establish some value for wall porosity. The singularity modelling of the airfoil initially covered only lift and volume but was extended to include drag and pitching moment, and second order volume term. It is shown by asymptotic transonic small disturbance analysis, that the derived corrections to angle of attack and free stream Mach number are correct to the first order.

Description: The effort to develop classical methods to compute wall interference at transonic speeds is outlined. The two-dimensional theory and three-dimensional development are discussed. Also, some numerical application of the two-dimensional work are indicated. The basic advantages of the asymptotic theory are noted.

Description: A solution for the tunnel wall boundary layer effects for three-dimensional subsonic tunnels is presented. The model potentials are represented with simple singularities placed on the centerline of the tunnel and Laplace's equation in cylindrical coordinates is solved for either the conventional homogeneous slotted-wall boundary condition, the solid-wall viscous boundary condition, or a combination of them. The most pronounced wall boundary layer effect is on solid blockage for completely closed wind tunnels. Boundary layers on the wall reduce the blockage from the solid-wall, no-boundary-layer case in a manner similar to opening slots in a solid wall. Additionally, for solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, whereas the lift interference factor at the model station does not depend on the boundary layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Description: Three experiments suitable for wall interference assessment and evaluation of proposed correction methods are presented. The experiments are: (1) a series of airfoil tests using a newly designed transonic flow facility that employs side-wall boundary layer suction and upper- and lower-wall shaping; (2) tests on a swept airfoil section spanning a solid-wall wind tunnel with fixed contouring on all four walls; and (3) tests on a swept wing of aspect ratio 3 mounted in a solid-wall wind tunnel with fixed flat walls. Each of the experiments provides data on the airfoil sections as well as on the wind tunnel walls. All the experiments were performed in solid wall wind tunnels corrected for boundary layer displacement effects. Although the experiments were performed primarily to evaluate computer code performance, it is believed that they also provide information that can be used to evaluate methods for assessing and correcting wall interference effects.

Description: Sidewall boundary layer effects were investigated by applying partial upstream sidewall boundary layer removal in the Langley 0.3-m transonic cryogenic tunnel. Over the range of sidewall boundary layer displacement thickness of these tests the influence on pressure distribution was found to be small for subcritical conditions; however, for supercritical conditions the shock position was affected by the sidewall boundary layer. For these tests (with and without boundary layer remove) comparisons with predictions of the GRUMFOIL computer code indicated that Mach number corrections due to the sidewall boundary layer improve the agreement for both subcritical and supercritical conditions. The results also show that sidewall boundary layer removal reduces the magnitude of the sidewall correction; however, a suitable correction must still be made.

Description: A validation of a measured boundary condition technique was carried out to demonstrate the feasibility of a wall interference assessment/correction (WIAC) system. An experimental evaluation was also carried out to compare performances of various techniques, to define the number of necessary boundary measurements for accurate assessment/corrections and to define the envelope of test conditions for which accurate assessment/corrections are achieved. The relative merits of a WIAC system and an adaptive wall tunnel are compared. The measurement surface boundary data is performed with a system of two rotating pipes. These pipes sweep out a cylindrical measurement surface near the tunnel walls, approximately one inch from the wall at the closest point. The experimental model was specially designed and fabricated for the adaptive wall experiments. The model is a wing/tail/body configuration with swept lifting surface. The boundary data taken in Tunnel 1T with the rotating pipe system has been shown to offer several attractive features for WIAC code evaluation. Good spatial resolution of measurements is achieved and measurements are made upstream and downstream of the model. Also, two velocity components are determined.

Description: The research undertaken concerning the computation and/or reduction of wall interference follows two main axes: improvement of wall correction determinations, and use of adaptive flexible walls. The use of wall-measured data to compute interference effects is reliable when the model representation is assessed by signatures with known boundary conditions. When the computed interferences are not easily applicable to correcting the results (especially for gradients in two-dimensional cases), the flexible adaptive walls in operation in T2 are an efficient and assessed means of reducing the boundary effects to a negligible level, if the direction and speed of the flow are accurately measured on the boundary. The extension of the use of adaptive walls to three-dimensional cases may be attempted since the residual corrections are assumed to be small and are computable.

Description: The following aspects of the planet Mars were assessed directly and indirectly by the Viking lander and Viking orbiter spacecraft: the atmosphere, craters, volcanoes, terrain, geology, and evolution. Descriptions of these aspects are included herein. It is concluded that though life is certainly not abundant on Mars, the possibility still exists that some form of life is extant there.

Description: The possibility of life on Mars, clues to the evolution of the solar system, fascination with the chemistry, geology, and meteorology of another planet led the National Aeronautics and Space Administration to Mars. Project Viking's goal, after making a soft landing on Mars, was to execute a set of scientific investigations that would not only provide data on the physical nature of the planet but also make a first attempt at determining if detectable life forms were present.

Description: To determine the low speed performance characteristics of a representative high aspect ratio supercritical wing, two low speed jet transport models were fabricated. A 12-ft. span model was used for low Reynolds number tests in the Langley 4- by 7-Meter Tunnel and the second, a 7.5-ft. span model, was used for high Reynolds number tests in the Ames 12-foot Pressure Tunnel. A brief summary of the results of the tests of these two models is presented and comparisons are made between the data obtained on these two models and other similar models. Follow-on two and three dimensional research efforts related to the EET high-lift configurations are also presented and discussed.

Description: Highlight results are presented from subsonic and transonic pressure measurement studies conducted in the Langley Transonic Dynamics Tunnel on a supercritical wing model representative of an energy efficient transport design. Steady- and unsteady-pressure data were acquired on the upper and lower wing surface at an off-design Mach number of 0.60 and at the design Mach number of 0.78, for a Reynolds number of 2.2 x 10(6) (based on the wing average chord). The model configuration consisted of a sidewall-Mounted half-body fuselage and a semi-span wing with an aspect ratio of 10.76, a leading-edge sweepback angle of 28.8 degrees, and supercritical airfoil sections. The wing is instrumented with 252 static pressure orifices and 164 dynamic pressure gages. Model test variables included wing angle of attack, control-surface mean deflection angle, control-surface oscillating deflection angle and frequency, and phasing between oscillating leading-edge and trailing-edge controls when used together.

Description: The prime objective of this experiment is to obtain chemical analyses of a statistically significant number of micrometeoroids. These data will then be compared with the chemical composition of meteorites. Secondary objectives of the experiment relate to density, shape, mass frequency, and absolute flux of micrometeorids as deduced from detailed crater geometrics (depth) diameter, and plane shape, and number of total events observed.

Description: The objective of this experiment is to measure the chemical and isotopic composition of interplanetary dust particles of mass greater than 10 to the minus 10 power G for most of thermator elements expected to be present.

Description: The history of remote sensing is reviewed and the scope and versatility of the several remote sensing systems already in orbit are discussed, especially those with sensors operating in other EM spectral modes. The multisensor approach is examined by interrelating LANDSAT observations with data from other satellite systems. The basic principles and practices underlying the use of thermal infrared and radar sensors are explored and the types of observations and interpretations emanating from the Nimbus, Heat Capacity Mapping Mission, and SEASAT programs are examined. Approved or proposed Earth resources oriented missions for the 1980's previewed include LANDSAT D, Stereosat, Gravsat, the French satellite SPOT-1, and multimission modular spacecraft launched from space shuttle. The pushbroom imager, the linear array pushbroom radiometer, the multispectral linear array, and the operational LANDSAT observing system, to be designed the LANDSAT-E series are also envisioned for this decade.

Description: The use of computer aided classification of LANDSAT data in developing water quality plans for New Jersey watersheds is used to exemplify how a state natural resource management program benefits from satellite imagery. The transition of a research and development system into an operational remote sensing system to help decision makers is demonstrated. Nontechnial issues that can assist (or hinder) an agency in adopting a new technology are examined. The progress of LANDSAT use by state government from the earliest stage of curiosity through to incorporation in actual state planning methods is charted. Potential applications of LANDSAT data to real information needs and solutions to management problems are examined. The problems and mistakes that occurred in using LANDSAT data in the past are discussed as well as the ways by which these problems were overcome.

Description: Information and activities are provided to: (1) enhance the ability to distinguish between a Geographic Information System (GIS) and a data management system; (2) develop understanding of spatial data handling by conventional methods versus the automated approach; (3) promote awareness of GIS design and capabilities; (4) foster understanding of the concepts and problems of data base development and management; (5) facilitate recognition of how a computerized GIS can model conditions in the present "real world" to project conditions in the future; and (6) appreciate the utility of integrating LANDSAT and other remotely sensed data into the GIS.

Description: The establishment of lunar bases is the next logical step in the exploration of space. Permanent lunar bases will support scientific investigation, the industrialization of space, and the development of self-sufficiency on the Moon. Scientific investigation and research and development would lead to applications utilizing lunar material resources. By utilizing these resources, the industrialization of space can become a reality. The above two factors coupled with the development of key and enabling technologies would lead to achievement of self-sufficiency of the lunar base. Attention was focused on specific design(s) to be pursued during subsequent stages in advanced courses. Some of the objectives in the project included: (1) minimizing the transportation of construction material and fuel from earth, or maximizing the use of the lunar material; (2) use of novel materials and light weight structures; (3) use of new manufacturing methods and technology such as magnetically levitated, or superconducting materials; and (4) innovative concepts of effectively utilizing the exotic lunar conditions, i.e. high thermal gradients, lack of atmosphere, zero wind forces, and lower gravity, etc.

Description: Based on the conservation of chemical elements in chemical reactions, a rule is proved that the number of boundary conditions given by densities and/or nonzero velocities should not be less than the number of chemical elements in the system, and the boundary conditions for species given by densities and velocities should include all elements in the system. Applications of this rule to Mars are considered. It is shown that the problem of the CO2-H2O chemistry in the lower and middle atmosphere of Mars, say, in the range of 0-80 km does not have a unique solution, if only CO2 and H2O densities are given at the lower boundary, and the remaining boundary conditions are fluxes. Two examples of models of this type are discussed. Two models of the photochemistry of the Martian atmosphere, with and without nitrogen chemistry, are considered. The oxygen nonthermal escape ratio of 1.2 x 10(exp 8)/cu cm/s is given at 240 km and is balanced with the total hydrogen escape rate within an uncertainty of 1% for both models. Both models fit the measured O2 and CO mixing ratios, the O3 abundance, and the O2 1.27-micrometer dayglow almost within the uncertainties of the measured values, though the model without nitrogen chemistry fits better. The importance of nitrogen chemistry in the lower and middle atmosphere of Mars depends on a fine balance between production of NO and N in the upper atmosphere which is not known within the required accuracy.

Description: Goethite-bearing samples with values of Mn(s) (Mn/(Mn+Fe) mole fraction) up to 0.206 were synthesized by precipitation from alkaline solution. Samples with Mn(s) less than or equal 0.061 were single-phase Mn-goethites: samples with higher Mn(s) values contained another Mn-bearing phase (probably jacobsite). Mn-hematites were prepared by dehydroxylation of corresponding Mn-goethites at 500 C. Orthorhombic a and b unit cell dimensions of Mn-goethites changed in a linear manner with Mn(s), but not at rates predicted by the Vegrad law. Hexagonal unit cell dimensions of Mn-hematites did not vary with Mn(s). Moessbauer parameters isomer shift (IS), quadrupole splitting (QS), and hyperfine field (B(sub hf)) were measured at 293 and 15 K. For all single-phase Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061), magnetic splitting was observed at both temperatures. At 293 K, small but systematic decreases in B(sub hf) were observed with increasing Mn substitution; IS and QS were not dependent on Mn(s). Mn substitution strongly lowered the Morin transition temperature of hematite. At 15 K, the Morin transition was not present for Mn(s) greater than 0.020(4). The saturation magnetization of Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061) was the expected zero (within error) for antiferromagnetic goethite and for hematites obtained from dehydroxylation of goethites. Mn-geothites with Mn(s) greater than 0.061 were magnetic because of the presence of strongly magnetic jacobsite. For reflectivity spectra, bands resulting from MN(3+) were centered near 454 and 596 nm for Mn-goethites and near 545 and 700 nm for Mn-hematites. There is evidence for a approximately 700 nm band in spectral data for Martian bright regions, but association of it with Mn(3+) is not a unique interpretation. Comparison of laboratory and Martian spectral data implies that Mn(s) less than 0.032 for the Mn(3+) content of Martian hematites.

Description: Ferric-iron-bearing materials play an important role in the interpretation of visible to near-IR Mars spectra, and they may play a similarly important role in the analysis of new mid-IR spacecraft spectral observations to be obtained over the next decade. We review exisiting data on mid-IR transmission spectra of ferric oxides/oxyhydroxides and present new transmission spectra for ferric-bearing materials spanning a wide range of mineralogy and crystallinity. These materials include 11 samples of well-crystallized ferric oxides (hematite, maghemite, and magnetite) and ferric oxyhydroxides (goethite, lepidocrocite). We also report the first transmission spectra for purely nanophase ferric oxide samples that have been shown to exhibit spectral similarities to Mars in the visible to near-IR and we compare these data to previous and new transmission spectra of terrestial palagonites. Most of these samples show numerous, diagnostic absorption features in the mid-IR due to Fe(3+) - 0(2-) vibrational transitions, structural and/or bound OH, and/or silicates. These data indicate that high spatial resolution, moderate spectral resolution mid-IR ground-based and spacecraft observations of Mars may be able to detect and uniquely discriminate among different ferric-iron-bearing phases on the Martian surface or in the airborne dust.

Description: The Multispectral Atmospheric Mapping Sensor (MAMS) is an airborne scanner which collects imagery in eight visible and three IR bands, with ground resolution of 100 m at a nominal aircraft altitude of 20 km. The visible channels provide continuous spectral coverage from 0.42 to 1.05 microns, and the IR channels measure upwelling and reflected radiation at combinations of 3.7, 6.5, 11.1, and 12.5 microns. These include channels nearly identical to the Landsat TM channels 1-4, and similar to those on the VISSR Atmospheric Sounder (VAS) and AVHRR instruments. The high spatial resolution permits investigation of surface thermal and atmospheric water vapor structure at scales not available from current stabilities. Significant modifications have been made since engineering flights in 1985 to improve the radiometric performance. The increased data quality and recent multidisciplinary applications of this data are presented.

Description: In summer 1988 an intensive field experiment was conducted in the vicinity of the Pisgah lava flow in the Mojave Desert. Physical properties such as microtopography, composition, soil moisture, and dielectric constant were measured at five sites representing surfaces with rms heights varying from less than one centimeter to tens of centimeters. In addition, polarimetric radar images at P-band, L-band, and C-band were acquired at three different incidence angles with the NASA/JPL airborne imaging radar polarimeter. Using trihedral corner reflectors deployed in the area prior to imaging, the L- and C-band images were calibrated to provide sigma0 values for each resolution element in the scene. The results of inferring geophysical parameters such as rms surface height and correlation length of the measured surfaces by fitting the observed signatures with those predicted by the small-perturbation model are presented: for smoother surfaces, the rms height values inferred are in good agreement with in situ measurements.

Description: Radar modeling of mangal forest stands in the Sundarbans area of southern Bangladesh is discussed. The modeling uses radar system parameters with forest data on tree height, spacing, biomass, species combinations, and water content (including slightly conductive water) in leaves and trunks of the mangal. For Sundri and Gewa tropical mangal forests, six model components are proposed; the models are required to explain the contributions of various combinations of forest species in the attenuation and scattering of mangal-vegetated nonflooded or flooded surfaces. Statistical data of simulated images have been compared with those of SIR-B images both to refine the modeling procedures and to characterize the model output appropriately. The possibility of delineation of flooded or nonflooded boundaries is discussed.