ALBERT

Description: Im Aufschluss Nußloch südlich von Heidelberg ist ein neu aufgeschlossener Lößrücken paläopedologisch aufgenommen und ein Standardprofil mit verschiedenen Methoden untersucht worden. Im Einzelnen wurden Sedimentanalysen (Korngrößen, Kohlenstoff, Kalkgehalt) und die magnetische Suszeptibilität bestimmt, biomorphologische und malakologische Untersuchungen durchgeführt sowie 27 Proben mit der IRSL-Methode datiert. Stratigraphisch umfasst der untersuchte Abschnitt das Jungpleistozän mit einem mehrgliedrigen Eem-Boden und einem ungewöhnlich mächtigen Würmlöß (ca. 18 m). Bodentypologisch wurden ein Bt-Horizont, eine Humuszone und zahlreiche Nassböden von unterschiedlicher Intensität mit und ohne Verbraunungszone nachgewiesen. Von den fünf ausgewiesenen Verbraunungszonen (WB2 - WB6) sind WB2, WB4 und WB5 aufgrund der Molluskenführung als interstadiale Bildungen anzusehen. Hinzu kommt noch eine der drei interstadialen Mosbacher Humuszonen (WB1) im stark reduzierten Altwürmabschnitt mit einem Alter von ca. 75 ka BP. Als kräftigster Interstadialboden ist der Bv-Horizont einer arktischen Braunerde erkannt worden (WB4), welcher aufgrund verschiedener Kriterien mit dem Lohner Boden bei ca. 30 ka BP parallelisiert wurde. Der im Hangenden des Lohner Bodens überlieferte Jungwürmlöß ist mit 12 m für Mitteleuropa sehr mächtig und von zahlreichen Nassböden (mindestens 10) untergliedert. Besonders aufgespaltet ist der Bereich des E2-Nassbodens, in dem auch die Böden WB5 und WB6 mit schwachen Verbraunungszonen liegen. Auch der jüngste Jungwürmlöß über dem Leithorizont des Eltviller Tuffs ist mit 4,5 m relativ mächtig und mehrgliedrig überliefert, so dass von einem E4/E5-Komplex gesprochen wird. Die paläopedologischen Befunde stimmen hervorragend mit den Veränderungen in der Molluskenfauna und der Suszeptibilitätskurve überein, so dass detaillierte stratigraphische und paläoklimatische Rekonstruktionen möglich sind. Die absoluten Altersdatierungen bestätigen dabei weitgehend die vorgenommenen Alterseinstufungen. Abschließend wird das neu bearbeitete Profil in Nußloch mit Ergebnissen von ANTOINE et al. (2001) verglichen, welche im gleichen Aufschluss an anderer Stelle erzielt worden sind.

Description: research

Description: Dieser Artikel diskutiert den Charakter von Pollentypen. Wir argumentieren, dass Pollentypen und Pflanzentaxa komplett unterschiedliche Entitäten (morphologische bzw. taxonomische) sind, und deswegen unterschiedlich behandelt und dargestellt werden sollten. Allgemeine Probleme der konventionellen Nomenklatur von Pollentypen werden anhand von Beispielen aus der europäischen palynologischen Praxis illustriert. Wir plädieren für Deutlichkeit in der Nomenklatur von Pollentypen und für die wissenschaftliche Freiheit, ‘unkonventionelle‘ Methoden zu benutzen, um Verwirrung zu vermeiden.

Description: research

Description: The new genus Lianus of subfamily Doryctinae (Hymenoptera: Braconidae) is described and illustrated. The differences from other genera of Doryctinae are discussed. Both included species originate from the Atlantic forest at Campos do Jordão, São Paulo State, Brazil.

Description: The Pterophoridae (Ochyroticinae, Deuterocopinae, Pterophorinae (Tribus: Platyptiliini, Exelastini, Oxyptilini)) species of the Neotropical fauna are reviewed. The species are redescribed. Moths are illustrated in colour for the first time, their genitalia are illustrated in line drawings. The examination of type specimens revealed the presence of four new synonyms: Platyptilia juanvinas Gielis, 1999, is a junior synonym of Platyptilia gravior Meyrick, 1932; Platyptilia jonesi Gielis, 1996, is a junior synonym of Platyptilia semnopis Meyrick, 1931; Oxyptilus maleficus Meyrick, 1926, is a junior synonym of Leptodeuterocopus neales (Walsingham, 1915); Lioptilus parvus Walsingham, 1880, is a junior synonym of Lioptilodes albistriolatus (Zeller, 1871). During the study of much new material 40 new species were discovered: Leptodeuterocopus tungurahue, L. angulatus, L. panamaensis, L. duchicela, Sochchora mulinus, Melanoptilia nigra, Platyptilia spicula, Stenoptilodes maculatus, S. agricultura, S. heppneri, S. medius, S. altiaustralis, Postplatyptilia nebuloarbustum, P. antillae, P. caribica, P. uruguayensis, P. pluvia, P. seitetazas, P. transversus, P. carchi, P. boletus, P, ugartei, P. drechseli, P. corticis, P. zongoensis, P. vorbecki, Amblyptilia landryi, A. kosteri, Lioptilodes altivolans, L. arequipa, L. yungas, L. salarius, L. cocodrilo, Michaelophorus margaritae, M. bahiaensis, Geina integumentum, Capperia browni, Buckleria brasilia, Megalorhipida paraiso, M. dubiosa. In the larger genera the species are arranged in groups. For a distinct group of species a new genus: Melanoptilia is proposed. A comprehensive checklist of the species has been made. To facilitate identification a key is presented to the genus level.

Description: A bibliography of the family Braconidae/Hymenoptera: Ichneumonidae is given for the period 1964-2003. It is an addition to Shenefelt's bibliography (1965), which covers the period 1785-1963. In total 10,436 references are listed.

Description: The European species of the genus Helorus Latreille, 1802, are keyed and illustrated, with special reference to their distribution in The Netherlands. Three of the four European species are newly reported for The Netherlands. The description of a new species from Sulawesi (Indonesia) is added: H. celebensis spec. nov.

Description: Two new genera of Entedoninae are described from Afrotropical region. The genus Janicharis gen. nov. (type species: J. africana spec. nov.) is described from Cameroon, Nigeria and Madagascar. The genus Hakuna gen. nov. (type species: H. matata spec. nov.) is described from Uganda. Both genera have a rather characteristic habitus and a peculiar propodeum bearing large anterolateral strips. A new, but yet unnamed, species of the genus Trisecodes Delvare & LaSalle, 2000, is recorded from Cameroon. This is the fi rst Afrotropical record of this genus, originally described from the Neotropical region.

Description: In total 32 new species of Tenthredinidae are described from Vietnam and 18 new species from Indonesia: Nesoselandria albotonkinensis spec. nov., N. albeotegularissima spec. nov., N. devriesiana spec. nov., Anapeptamena achterbergiana spec. nov., Neostromboceros nigrogiganteus spec. nov., N. gracilioides spec. nov., N. alboclypeatus spec. nov., N. daoensis spec. nov., N. phuongensis spec. nov., Abusarbidea bicoloristigmata spec. nov., Eusunoxa alboapicalis spec. nov., Neopoppia tonkinometallica spec. nov., Abeleses vietnamensis spec. nov., A. metallotonkinensis spec. nov., Heptamelus tonkinensis spec. nov., Athlophorus devriesi spec. nov., Rhopographus vietnamensis spec. nov., Xenapatidea hematothoracica spec. nov., X. devriesi spec. nov., Allantidea achterbergiana spec. nov., Neothrinax nigrotonkinensis spec. nov., Indotaxonus flavissimus spec. nov., Darjilingia vietnamensis spec. nov., D. tonkinensis spec. nov., D. hoangliensis spec. nov., Ferna achterbergi spec. nov., Monophadnus bicoloritonkinensis spec. nov., Eutomostethus phongdiensis spec. nov., Eutomostethus albotegularissimus spec. nov., Tenthredo octomaculatus spec. nov., T. tricoloritonkinensis spec. nov. and T. danangiensis spec. nov. from Vietnam. Neostromboceros pleuronotatus spec. nov., N. albopedissimus spec. nov., N. flavopedis spec. nov., N. rubroguinealis spec. nov., N. rubromalayensis spec. nov., Eusunoxa malaya spec. nov., Emphytus danumiensis spec. nov., Hemibeleses sulawesiensis spec. nov., Neopoppia irregulata spec. nov., Tenthredo nigrosabahensis spec. nov., T. djampangensis spec. nov., Neothrinax kaindiensis spec. nov., N. excavata spec. nov., N. gedehensis spec. nov., Abeleses metallojavanus spec. nov., Caliroa nigrojavana spec. nov., Nesoselandria sulawesiensis spec. nov. and Athlophorus achterbergianus spec. nov. from Indonesia. Monophadnus glaucus Enderlein, 1919; Monophadnus sumatranus Enderlein, 1919; Amonophadnus nigripennis Benson, 1935; Amonophadnus nigrojavanus Haris, 2002; Corporaalinus azureus Forsius, 1925; Corporaalinus cyanescens Forsius, 1925; and Corporaalinus jacobsoni Forsius, 1929, are proposed as new synonyms of Monophadnus rivalis Konow, 1906. An identification key is added for the known Tenthredinidae of Borneo, Sumatra, Java, Sulawesi and New Guinea.

Description: Two new host records for Exasticolus fuscicornis (Cameron, 1887)(Hymenoptera: Braconidae: Homolobinae)are presented with detailed larvae morphology and other biological information.

Description: Thirty species belonging to 16 genera of the family Braconidae (Hymenoptera) are reported from Greenland. Seven are new species described and illustrated below: Dacnusa groenlandica spec. nov.; Aphidius tarsalis spec. nov.; Praon brevistigma spec. nov.; Blacus (B.) groenlandicus spec. nov.; Cotesia crassifemorata spec. nov.; C. fascifemorata spec. nov. and Microplitis lugubroides spec. nov.

Description: The little-known monotypic genus Paracyphocrania Redtenbacher, 1908 (Phasmatinae: Phasmatini) is reviewed and now comprises two species: P. lativentris Redtenbacher, 1908, and P. tecticollis (Redtenbacher, 1908) comb. nov., which are redescribed and illustrated. A neotype is designated for P. lativentris which is newly recorded from Sulawesi.

Description: Vestalaria vinnula spec.nov. (holotype male, southern Vietnam, Lam Dong province, Blao, 1962) is described in both sexes and compared with other species of Vestalaria May, 1935 (= the Vestalis smaragdina - group), which is ranked as valid genus.

Description: A new species of the genus Artocella van Achterberg is described from Spain. On the basis of its substantial sexual dimorphisim, the differences between the two previously known species of this Turanian-Mediterranean genus, which had each been described from specimens of only one (and differing) sex, are reassessed.

Description: Dasypoda intermedia spec. nov. from Iran is described. Its description fills a gap of our knowledge of the East Mediterranean fauna of the genus Dasypoda. The West Mediterranean Dasypoda species are well known but the eastern species lack convincing records. Moreover, D. intermedia spec. nov. is a very interesting species from a phylogenetic point of view. It shares some characters common to subgenera Dasypoda s. str. and Megadasypoda Michez, 2004, which provide further evidence for the close relationship of both subgenera.

Description: Thirty-one species of the family Platystictidae of the Philippines are revised, i.e. all species recognised, excluding the species of the Drepanosticta halterata-group. The following new taxa are described: 16 species in Drepanosticta Laidlaw: D. acuta spec. nov., D. aurita spec. nov., D. centrosaurus spec. nov., D. clados spec. nov., D. flavomaculata spec. nov., D. furcata spec. nov., D. hermes spec. nov., D. krios spec. nov., D. luzonica spec. nov., D. malleus spec. nov., D. myzouris spec. nov., D. paruatia spec. nov., D. pistor spec. nov., D. quadricornu spec. nov., D. rhamphis spec. nov., D. trachelocele spec. nov., two in Protosticta Selys, viz. P. lepteca spec. nov. and P. plicata spec. nov., and three in Sulcosticta gen. nov., viz. S. striata spec. nov., S. pallida spec. nov. and S. viticula spec. nov. The status of eleven previously described nominal taxa is established. One, D. septima Needham & Gyger, is doubtfully considered a synonym of D. mylitta Cowley. Based on a preliminary phylogenetic analysis, the species of Drepanosticta are divided into informal species groups. Most species of the Philippines have affinities to species of Sulawesi, the Moluccas and New Guinea. Several species confined to Palawan have sister-group relationships with species from Borneo. The affinities of various other species confined to the Sulu archipelago, are unsettled as yet. The species of Platystictidae here assigned to Protosticta Selys are presumably not closely related to the type species, P. simplicinervis Selys from Sulawesi. However, a better placement has to await a more detailed phylogenetic study of the family. For three species the new genus Sulcosticta gen. nov. is erected. These species are closely allied based on the structure of the appendages, but should have been assigned to different genera if based on the present generic definitions. Many species here described have small distributional ranges, a common phenomenon in Platystictidae. Since most forests in the Philippines are heavily under threat or have already disappeared in the last fifty years, several taxa described in this paper should be considered under threat of immediate extinction.

Description: In this part the remaining 78 species of the genus Pepsis, belonging to ten species-groups, are described and figured, and their phylogenetics and biogeography are discussed. 14 of the species are described as new: P. achterbergi spec. nov., P. adonta spec. nov., P. boharti spec. nov., P. caliente spec. nov., P. dayi spec. nov., P. esmeralda spec. nov., P. ianthoides spec. nov., P. jamaicensis spec. nov., P. krombeini spec. nov., P. martini spec. nov., P. multichroma spec. nov., P. nanoides spec. nov., P. wahisi spec. nov., and P. willinki spec. nov. Three species-names, P. infuscata Spinola, 1841, P. lampas Lucas, 1895, and P. thoreyi Dahlbom, 1845, are recalled from synonymy. The following 293 names are newly synonymized (the valid names are listed first): P. atalanta Mocsáry, 1885 = P. nitens Mocsáry, 1894, P. mocsaryi Lucas, 1895; P. inclyta Lepeletier, 1845 = P. mutabilis Lepeletier, 1845, P. vagabunda Lepeletier, 1845, P. cupripennis Taschenberg, 1869, P. violaceipennis Mocsáry, 1885, P. clotho Mocsáry, 1888, P. spengeli Mocsáry, 1888, P. sickmanni Mocsáry, 1888, P. nireus Mocsáry, 1894, P. atrovirens Lucas, 1895, P. cerastes Lucas, 1895, P. pygidialis Brèthes, 1908, P. guaranitica Brèthes, 1908, P. parca Lucas, 1919, P. atahualpa Banks, 1946, opimicornis, Haupt, 1952, atropos, Haupt, 1952, azurea Haupt, 1952; crassicornis Mocsáry, 1885 = P. sappho Brèthes, 1908, P. nitocris Brèthes, 1908, P. vivida Brèthes, 1908, P. arechavaletai Brèthes, 1908, P. lynchii Brèthes, 1908, P. operosa Brèthes, 1908, P. ataraqua Banks, 1946, P. splendida Haupt, 1952; P. sommeri Dahlbom, 1845 = P. azteca Cameron, 1893; P. xanthocera Dahlbom, 1843 = P. nigrescens Smith, 1855, P. fulgidipennis Mocsáry, 1885, P. juno Brèthes, 1908, P. ismare Banks, 1946, P. nigroprasina Haupt, 1952; P. seifferti Lucas, 1895 = P. cornuta Lucas, 1895, P. moebiusi Lucas, 1895, P. stygia Lucas, 1895; P. luteicornis Fabricius, 1804 = P. strenua Erichson, 1848, P. tinctipennis Smith, 1873, P. citreicornis Mocsáry, 1894, P. venosa Banks, 1945, P. alector Banks, 1946; P. asteria Mocsáry, 1894 = P. luridicornis Brèthes, 1926; P. convexa Lucas, 1895 = P. humeralis Brèthes, 1914; P. helvolicornis Lucas, 1895 = P. bahiae Brèthes, 1914; P. vitripennis Smith, 1855 = P. obscura Lepeletier, 1845, P. amabilis Mocsáry, 1885, P. centralis Cameron, 1893, P. margarete Lucas, 1895, P. venezuelae Kaye, 1913, P. aeneipennis Banks, 1946, P. helenae Haupt, 1952, P. coeruleoviridis Haupt, 1952; P. fumipennis Smith, 1855 = P. pallidicornis Mocsáry, 1885; P. amyntas Mocsáry, 1885 = P. vicina Lucas, 1895, P. clarinervis Brèthes, 1908, P. amyntoides Lucas, 1919, P. eurydice Lucas, 1919; P. dimidiata Fabricius, 1804 = P. vittigera Lucas, 1897, P. argentina Brèthes, 1908, P. sanctaeannae Brèthes, 1908, P. virgo Brèthes, 1908, P. externa Brèthes, 1908, P. transversa Brèthes, 1908, P. cordubensis Brèthes, 1908, P. banghaasi Lucas, 1919; P. menechma Lepeletier, 1845 = P. elegans Lepeletier, 1845, P. dubitata Cresson, 1867, P. prismatica Smith, 1855, P. advena Mocsáry, 1885, cinctipennis Mocsáry, 1885, P. guatemalensis Cameron, 1893, P. nestor Mocsáry, 1894, P. nigricornis Mocsáry, 1894, P. auranticornis Lucas, 1895, P. fruhstorferi Lucas, 1895, P. concolor Lucas, 1895, P. cerberus Lucas, 1895, P. euchroma Lucas, 1895, P. nigrocincta Lucas, 1895, P. mordax Lucas, 1895, P. inermis Fox, 1898, P. roberti Brèthes, 1908, P. janira Brèthes, 1908, P. cultrata Brèthes, 1908, P. novitia Banks, 1921; P. decipiens Lucas, 1895 = P. similis Lucas, 1895; P. minarum Brèthes, 1914 = P. pulchra Brèthes, 1914; P. basifusca Lucas, 1895 = P. angustimarginata Viereck, 1908; P. chrysoptera Burmeister, 1872 = P. exigua Lucas, 1895, P. smaragdinula Lucas, 1895, P. nebulosa Lucas, 1895, P. karschi Lucas, 1895, P. anisitsii Brèthes, 1908, P. indistincta Brèthes, 1908, P. dimidiatipennis Brèthes, 1908, P. chloroptera Brèthes, 1908, P. culta Brèthes, 1908, P. recta Brèthes, 1908, P. tornowii Brèthes, 1908, P. schrottkyi Brèthes, 1908, P. itinerata Brèthes, 1908, P. miniata Brèthes, 1908, P. spegazzinii Brèthes, 1908, P. paulistana Brèthes, 1914, P. chloe Brèthes, 1914, P. coronaria Brèthes, 1914, P. semilucana Haupt, 1952, P. bruneipes Haupt, 1952, P. brachynotus Haupt, 1952, P. diagonalis Haupt, 1952, P. discrepans Haupt, 1952; P. elongata Lepeletier, 1845 = P. purpurascens Smith, 1855, P. fuscipennis Smith, 1873, P. longula Banks, 1946; P. australis Saussure, 1867 = P. centaurus Lucas, 1897; P. cyanescens Lepeletier, 1845 = P. micans Mocsáry, 1885, P. jucunda Mocsáry, 1885, P. balloui Banks, 1946, P. diversa Haupt, 1952; P. lampas Lucas, 1895 = P. venturii Schrottky, 1902; P. nitida Lepeletier, 1845 = P. lucidula Smith, 1855, P. vaualba Smith, 1855, P. pruinosa Mocsáry, 1894, P. cylindrica Lucas, 1895, P. andina Brèthes, 1908, P. dilatata Brèthes, 1908, P. holmbergi Brèthes, 1908, P. concava Brèthes, 1908, P. ephebus Brèthes, 1908, P. vaga Brèthes, 1908, P. fuscobasalis Brèthes, 1908, P. cordata Brèthes, 1914, P. impatiens Brèthes, 1914, P. tricolor Brèthes, 1914, P. joergenseni Brèthes, 1914, P. cleone Brèthes, 1914, P. dorsata Brèthes, 1914, P. aretheas Brèthes, 1914, P. lassonis Lucas, 1819, P. consors Banks, 1946, P. interrupta Banks, 1946, P. analis Haupt, 1952; P. seladonica Dahlbom, 1843 = P. deuteroleuca Smith, 1855, P. kohli Lucas, 1895, P. venezolana Brèthes, 1908, P. burmeisteri Brèthes, 1908; P. cybele Banks, 1945 = P. weberi Banks, 1946; P. thoreyi Dahlbom, 1845 = P. lurida Lucas, 1895, P. euterpe Brèthes, 1908; P. flavescens Lucas, 1895 = P. periphetes Lucas, 1895, P. limbatella Brèthes, 1908, P. discoidalis Brèthes, 1914, P. limbatica Brèthes, 1914, P. militaris Brèthes, 1914, P. cavillatrix Haupt, 1952, P. arcuata Haupt, 1952, P. recterugosa Haupt, 1952, P. adversatrix Haupt, 1952; P. nigricans Lucas, 1895 = P. troglodytes Brèthes, 1908; P. montezuma Smith, 1855 = P. quitonensis Packard, 1869, P. sibylla Mocsáry, 1885, P. circe Mocsáry, 1885, P. occidentalis Cameron, 1893, P. peruanus Lucas, 1895, P. fulva Lucas, 1895, P. nessus Lucas, 1895, P. fusca Lucas, 1895, P. andicola Cameron, 1903, P. chilloensis Cameron, 1903, P. patagonica Brèthes, 1908, P. fasciculata Brèthes, 1908, P. pisoensis Strand, 1911, P. pacifica Brèthes, 1914, P. huascar Banks, 1946; P. completa Smith, 1855 = P. quichua Brèthes, 1908, P. comes Banks, 1946; P. smaragdina Dahlbom, 1843 = P. thunbergi Dahlbom, 1843, P. lara Mocsáry, 1888, P. satrapes Lucas, 1895, P. nupta Lucas, 1895, P. erynnis Lucas, 1895, P. fraterna Lucas, 1895, P. diabolus Lucas, 1895, P. mystica Lucas, 1895, P. thalia Brèthes, 1908, P. brasiliensis Brèthes, 1908, P. pallida Brèthes, 1908, P. iheringi Brèthes, 1908, P. dromeda Brèthes, 1908, P. sepultrix Lucas, 1919, P. strickeri Lucas, 1919; P. discolor Taschenberg, 1869 = P. sinnis Lucas, 1895, P. jujuyensis Brèthes, 1908, P. modesta Brèthes, 1908, P. comparata Brèthes, 1908, P. neutra Brèthes, 1908, P. terebrans Brèthes, 1908, P. procera Haupt, 1952, P. plaumanni Haupt, 1952, P. ogloblini Haupt, 1952, P. deletrix Haupt, 1952; P. limbata Guérin, 1831 = P. richteri Brèthes, 1908, P. polita Brèthes, 1908, P. limbella Haupt, 1952, P. artemis Haupt, 1952; P. basalis Mocsáry, 1885 = P. erdmanni Lucas, 1895, P. basinigra Haupt, 1952; P. infuscata Spinola, 1841 = P. niobe Mocsáry, 1885, P. sagana Mocsáry, 1894, P. incerta Banks, 1946; P. hyalinipennis Mocsáry, 1885 = P. subruficornis Haupt, 1952; P. festiva Fabricius, 1804 = P. pulchella Lepeletier, 1845, P. solitaria Smith, 1879, P. gallardoi Brèthes, 1908, P. hora Brèthes, 1914, P. amok Lucas, 1919, P. riojaneirensis Lucas, 1919; P. gracilis Lepeletier, 1845 = P. diana Mocsáry, 1885, P. hecate Mocsáry, 1885, P. spathulifera Lucas, 1895, P. sphinx Lucas, 1895, P. ierensis Banks, 1945, P. alceste Banks, 1946, P. scalaris Haupt, 1952; P. mildei Stål, 1857 = P. charon Mocsáry, 1885, P. cyanoptera Lucas, 1895, P. dryas Lucas, 1919; P. filiola Brèthes, 1914 = P. denserugosa Haupt, 1952; P. ruficornis Fabricius, 1804 = P. saphirus Palisot de Beauvois, 1805, P. violacea Mocsáry, 1885, P. hexamita Lucas, 1895, P. omniviolacea Haupt, 1952; P. brunneicornis Lucas, 1895 = P. glabripennis Lucas, 1895; P. purpurea Smith, 1873 = P. pan Mocsáry, 1885, P. parthenope Mocsáry, 1885, P. sagax Lucas, 1895, P. clypeata Brèthes, 1914, P. consimilis Banks, 1946, P. laconia Banks, 1946; P. viridisetosa Spinola, 1841 = P. eximia Smith, 1873; P. viridis Lepeletier, 1845 = P. errans Lepeletier, 1845, P. chlorotica Mocsáry, 1885, P. excelsa Lucas, 1895, P. selene Lucas, 1895, P. fimbriata Lucas, 1895, P. calypso Brèthes, 1908, P. fluminensis Brèthes, 1908, P. argentinicus Strand, 1910, P. mimetica Brèthes, 1914, P. garbei Brèthes, 1914, P. erecta Brèthes, 1914, P. tandilensis Brèthes, 1914, P. meridionalis Brèthes, 1914, P. minor Lucas, 1919, P. basifulgens Lucas, 1919, P. nebulosipennis Lucas, 1919, P. purpurea Lucas, 1919, P. koerberi Lucas, 1919, P. inimicissima Lucas, 1919, P. debilitans Lucas, 1919, P. itapaca Banks, 1946; P. aciculata Taschenberg, 1869 = P. nero Lucas, 1895; P. atripennis Fabricius, 1804 = P. flavilis Brèthes, 1908; P. ianthina Erichson, 1848 = P. fulvicornis Mocsáry, 1885, P. sirene Lucas, 1895, P. balboae Lucas, 1919, P. herodes Lucas, 1919, P. curti Lucas, 1919; P. nana Mocsáry, 1885 = P. mapiriensis Lucas, 1919, P. vinciens Lucas, 1919, P. ilione Banks, 1946, P. moesta Banks, 1946, P. orestes Banks, 1946, P. amautas Banks, 1946, P. inaequalis Haupt, 1952; P. hirtiventris Banks, 1946 = P. viridaurea Haupt, 1952, P. aequalis Haupt, 1952; P. auriguttata Burmeister, 1872 = P. aurimacula Mocsáry, 1885, P. flavicornis Mocsáry, 1894, P. guttata Lucas, 1895, P. incendiaria Lucas, 1895, P. pubiventris Lucas, 1895, P. planifrons Lucas, 1895, P. lestes Lucas, 1895, P. villosa Brèthes, 1908; P. sabina Mocsáry, 1885 = P. astioles Banks, 1946; and P. purpureipes Packard, 1869 = P. chlorana Mocsáry, 1885, P. antennalis Cameron, 1893, P. sulcifrons Cameron, 1903, P. carinata Brèthes, 1914, P. equatoriana Brèthes, 1914, P. angusta Banks, 1946. Keys to all forms are given. The mimicry-groups of P. atripennis Fabricius, 1804, and P. completa Smith, 1855, are defined and described and a comparative account of mimicry based on all four mimicrygroups in Pepsis is given. Lists of excluded species (with their current taxonomic placement and depository where ascertained), unplaced names, and a nomen nudum are given.

Description: Menippus philippinensis Jacoby, 1894, is reported from Java, and Issikia clarki (Jacoby, 1884) comb. nov., from Sumatra.

Description: New and old records of the robberfly Machimus cowini in the Netherlands (Diptera: Asilidae) Until recently, Machimus cowini (Hobby, 1943) was known from just one record in the Netherlands. An examination of Dutch specimens of the similar M. cingulatus revealed specimens of M. cowini from five new localities. The records are concentrated on the island Ameland and along the rivers Waal and Maas. On Ameland, M. cowini probably occurs in coastal dunes. Near Nijmegen the species was found in grassy vegetation on floodplains and on riverdunes near the river.

Description: Two new species of the genus Diachasmimorpha Viereck, 1913 (Braconidae: Opiinae) are described: D. feijeni spec. nov. from Bhutan (reared from Bactrocera minax (Enderlein) (Diptera: Tephritidae) in fruits of Citrus reticulata Blanco (mandarin)) and D. budrysi spec. nov. from Far East Russia. A key to the Palaearctic species is added, including two similar species (Fopius alternatae (Tobias, 1977), and F. myolejae (Tobias, 1977)).

Description: Pemphredon montana, new to The Netherlands (Hymenoptera: Sphecidae) In 1998 Pemphredon montana Dahlbom, 1845 was recorded for the first time in the Netherlands. The species was found nesting in the insulating material of a caravan in the northernmost part of the province of Overijssel.

Description: The influence of recent inundations on the distribution pattern of the isopod Eluma purpurascens in the province of Zeeland (Crustacea: Isopoda: Oniscoidea) Small scale mapping of Eluma purpurascens Budde-Lund, 1885 in the province of Zeeland revealed a remarkable distribution pattern. The species proved to be absent in parts which have been inundated during and after the second world war. This study shows that for the interpretation of distribution patterns the history of the study area should be considered.

Description: Faunistics and ecology of the syrphid genus Epistrophe in The Netherlands (Diptera: Syrphidae) Ten species of Epistrophe have been found in the Netherlands, two of which, E. cryptica and E. similis, are recorded here for the first time. The distribution, changes in distribution and ecology of the species were investigated and are illustrated by distribution maps and diagrams of the flight period. In all species, except E. eligans, females were observed more than males. Furthermore, females seem to be active later in the season than males. It is discussed that this is probably caused by the differences in behaviour between the males of the species.

Description: Until recently Boreus hyemalis was considered to be a rare species in The Netherlands. It was only known from a few localities in The Netherlands in the provinces of Noord-Holland, Zuid- Holland, Utrecht, Gelderland and Drenthe. The last few years many new populations have been discovered. In this paper the first records for the provinces of Limburg, Noord-Brabant and Overijssel are presented. The species seems to prefer scarcely vegetated patches in sanddunes, dominated by greyhair grass Corynephorus canescens and the moss Polytrichum piliferum. It proved to be relatively easy to find, when the right places were searched in the right period (October until February).

Description: Het genus Bryotropha in Nederland (Lepidoptera: Gelechiidae) Het genus Bryotropha staat bekend als een notoir lastig geslacht van kleine bruine motjes. Die moeilijkheid komt door de variatie, maar vooral ook door gebrek aan bruikbare beschrijvingen. Met dit artikel zijn de negen Nederlandse soorten te determineren. Vanwege het gebrek aan determinatieliteratuur in heel Europa is het in het Engels geschreven. Behalve de maar één keer waargenomen B. domestica, zijn de meeste soorten vrij gewone verschijningen in ons land, zoals uit de kaarten blijkt.

Description: The occurrence of Digitivalva arnicella in the Netherlands: rediscovery and conservation (Lepidoptera: Plutellidae: Acrolepiinae) Digitivalva arnicella (Heyden, 1863), previously only known from two localities before 1902, has been rediscovered in eight localities in the northern part of the Netherlands (province of Drenthe) on its host Arnica montana. On the basis of leafmines, found in old herbarium collections, it can be concluded that the species was once widespread within the range of its host in the northern and eastern parts of the Netherlands and has apparently been overlooked by entomologists since. D. arnicella is a much endangered species in the Netherlands, because of the dramatic decline of its host. Two of the eight discovered populations have been lost since their discovery in the first half of the 1990’s. Systematics and life history of the species are described and illustrated, the distribution is mapped and advise for management of its sites are given. The current management of some populations of Arnica, by mowing the site completely in August, is disastrous for the young caterpillars, mining the leaves.

Description: Nemobius sylvestris in the dunes near Bergen (Orthoptera) A large population of Nemobius sylvestris (Bosc, 1792) has been found in the dunes near Bergen (Noord-Holland), 60 km northwest of the nearest known site in the Gooi-area. This discovery sheds new light on a specimen from Bergen found in a collection, which was thought to be mislabelled.

Description: Interesting new records of Odonata in the Netherlands in 1998 A survey of the most interesting observations on Dutch Odonata is presented. During the Odonata Recording Scheme many new records of rare species have become available. Gomphus flavipes, G. vulgatissimus, Anax parthenope, Sympetrum pedemontanum and S. depressiusculum seem to become more common. The status of some threatened species is elucidated: Calopteryx virgo, Sympecma paedisca, Coenagrion hastulatum and Cordulegaster boltonii.

Description: The West Palaearctic species of the subfamily Paxylommatinae are reviewed and the species of the genus Hybrizon Fallén, 1813, from the Palaearctic region are keyed. Hybrizon juncoi (Ceballos, 1957) is recognized as a valid species, a neotype is designated for Hybrizon latebricola Nees, 1834, and a lectotype is designated for Plancus apicalis Curtis, 1833. Paxylomma grandis Rudow, 1883, Ogkosoma schwarzi Haupt, 1913, and Eurypterna arakawae Matsumura, 1918, are new junior synonyms of Eurypterna cremieri (de Romand, 1838).

Description: Het genus Scrobipalpa in Nederland (Lepidoptera: Gelechiidae) Scrobipalpa is een geslacht van kleine, lastig uit elkaar te houden motjes. In heel Europa zijn ongeveer 70 soorten bekend. Doorgaans zijn de vleugels bruin- of grijsachtig met een tekening van stippels en strepen die bovendien erg kan variëren. Hierdoor kunnen de individuele soorten vaak moeilijk herkend worden. Aan de hand van de genitaliën kunnen soorten wel allemaal gedetermineerd worden. Omdat de literatuur over deze groep niet erg toegankelijk is en bestaande beschrijvingen soms erg onvolledig zijn, wordt dit artikel in het Engels geschreven. Met dit artikel zijn de elf Nederlandse soorten te determineren. De meeste hiervan zijn min of meer gebonden aan de kust. Van alle soorten worden naast beschrijvingen van de vleugeltekening en de genitaliën, ook de verspreiding, de biologie en de ecologie gegeven.

Description: New records of Cheilosia caerulescens in the Netherlands (Diptera: Syrphidae) Cheilosia caerulescens is a rare hoverfly in The Netherlands. Until 1998 only four records were known, the first in 1986. In 1998 the species was found on three new and one old locality. The record from Heemstede (province of Noord-Holland) is among the northernmost in the European distribution of this species. Three of the four records originate from gardens.

Description: Chironomidae in newly created nature reserves In a newly created nature reserve near Eindhoven many interesting species of Chironomidae were found. Several new species to the Dutch fauna were identified and one species (of the genus Neozavrelia) proved to be new to science. The fauna of these young habitats is poorly known, but proves to be very interesting.

Description: A key to the European species of the Pteromalus altus group is presented. The relationship between this group and species of the genus Euphorbia (Euphorbiaceae) is confirmed. One new species: P. villosae, associated with Euphorbia villosa Waldst. & Kit.is presented. Two new species of the albipennis group: Pteromalus almeriensis and P. costulata are presented. In addition one species of the P. vibulenus group: P. tethys is added. Information on P. sylveni Hedqvist, P. osmiae Hedqvist and P. discors Graham is given.

Description: The species of Encarsia Foerster (Hymenoptera: Aphelinidae) known from Egypt are revised. A total of 14 species are treated, including one new species. E. indifferentis Mercet, 1929, is synonymised with E. inaron (Walker, 1839). All species are fully described or diagnosed, and illustrated. Host records, and species-distributions outside Egypt, are given.

Description: Interesting records of beetles in The Netherlands (Coleoptera: Staphylinidae, Nitidulidae, Dermestidae) Tachyporus quadriscopulatus Pandellé, 1869 has been recorded for the second time in the Netherlands at Arcen and Velden, province of Limburg. After 27 years, a third record of Carpophilus marginellus Motschulsky, 1858 can be reported from St. Geertruid, in the southern part of the province of Limburg. One specimen was found outdoors, in a wood. One specimen of Anthrenocerus australis Hope, 1843 was also found outdoors, in Oost- Maarland also in southern Limburg, sitting on a flower in a meadow.

Description: Butterflies in the Netherlands still under pressure (Lepidoptera: Rhopalocera) New information on the Dutch Rhopalocera fauna since the distribution atlas of Tax (1989) is presented. Coenonympha pamphilus was common in large parts of the Netherlands, but has declined dramatically. C. arcania is now formally extinct in our country. An extensive research showed that Maculinea alcon ericae has dissappeared from many sites. Furthermore the smallest of the two remaining populations of Heteropterus morpheus seems to have gone extinct. On the other hand, Callophrys rubi, has colonized new territory. Lampidus boeticus, was observed once as an adult and once a caterpillar was found between snow peas from Egypt. Colias croceus was very abundant in 1998. The reintroductions of Maculinea teleius and M. nausithous in 1990 appear to have been successful.

Description: The rearing of the botfly Cephenemyia auribarbis (Diptera: Oestridae) After several failures we finally succeeded in rearing botflies Cephenemyia from third-instar larvae. From a red deer shot at 13 March 1998 about one hundred larvae of Cephenemyia auribarbis (Meigen, 1824) were collected. Ten individuals reached the pupal stage. After 22 days, one fullgrown male died in the pupa, and two males emerged and lived for 17 and 18 days respectively. This is one of the few recorded succesful attempts to rear botflies.

Description: A new record of Chorthippus apricarius in the Netherlands (Orthoptera) Chorthippus apricarius is a very rare grasshopper in The Netherlands. Only three, very widely separated sites are known. In 1998 a small new population has been found in a roadside verge, 2 km southwest of the southernmost site in the south of the province of Limburg.

Description: Checklist of the Nitidulidae and Brachypteridae (Coleoptera) of the Netherlands and surrounding regions An annotated checklist of the Nitidulidae and Brachypteridae of the Netherlands and surrounding regions is presented, based mainly on literature research. Since the list of Brakman seven new species to the Netherlands have been published. One of these species, Pocadius adustus, is listed here for the first time. Major nomenclatorial changes, published elsewhere, have been implemented. The list contributes to the faunistic work of the European Invertebrate Survey - The Netherlands. A separate list of hostplants of the Nitidulidae and Brachypteridae is presented.

Description: Galeruca malakkana spec. nov., a new species is described from Malaysia.

Description: A new genus of the subfamily Alysiinae (Braconidae) is reported from South Africa (Bobekoides gen. nov.; type species: Bobekoides fulvus spec. nov.), illustrated, and described. A key to the species is added. The new genus is closely related to the East Palaearctic genus Hylcalosia Fischer, 1967.

Description: A synopsis of the genus Rhodopygia Kirby is given. Its species are discussed and their diagnostic morphological characters elucidated by figures. The hitherto unknown females of R. hinei Calvert and R. pruinosa Buchholz are described. A key to the species is provided.

Description: For the first time a gregarious parasitoid belonging to the genus Phaenocarpa Foerster, 1862 (Braconidae: Alysiinae) is reported, and described as P. helophilae spec. nov. from England. The first record of Chloropidae as host for a Phaenocarpa species is given; P. livida (Haliday, 1838) reared from Calamoncosis (Rhaphiopyga) glyceriae Nartshuk, 1958. Sathra debilis Foerster, 1862, is synonymised with P. livida (Haliday). Additionally, Phaenocarpa curticauda spec. nov. from The Netherlands is described and fully illustrated. A lectotype is designated for Alysia pectoralis Zetterstedt, 1838, and Phaenocarpa rufoflava Papp, 1968, is recognised as a valid species.

Description: The assassin bug genus Rasahus Amyot & Serville (Heteroptera: Reduviidae: Peiratinae) comprises 26 Neotropical species. A cladistic analysis of the genus was carried out using 63 characters from external morphology, body vestiture, and male and female genitalia, with the species considered as terminal taxa. The analysis yielded 149 equally parsimonious cladograms, each with 206 steps, CI = 0.35, and RI = 0.60; the successive weighting procedure resulted in eight cladograms (CI = 0.79 and RI = 0.91). In the strict consensus cladogram, two major clades are delimited: one comprising the species R. rufiventris, R. hamatus, R. arcitenens, R. arcuiger, R. amapaensis, R. thoracicus, R. biguttatus, R. argentinensis, R. limai, R. grandis, and R. angulatus; and the other with R. castaneus, R. aeneus, R. scutellaris, R. maculipennis, R. brasiliensis, R. sulcicollis, R. surinamensis, R. albomaculatus, R. guttatipennis, R. atratus, R. peruensis, R. costarricensis, R. bifurcatus, R. flavovittatus, and R. paraguayensis. A cladistic biogeographic analysis of the provinces of the Neotropical subregion, considering distributional data of the species of Rasahus and three other genera of Peiratinae (Eidmannia, Melanolestes, and Thymbreus) was carried out. Four general area cladograms were obtained applying programs COMPONENT 2.0 and TASS. The most parsimonious general area cladogram (= implying fewer items of error) was obtained with COMPONENT 2.0 minimizing the number of leaves added, and shows the sequence (Desierto, (Caatinga, (Cerrado, (Chacoan, (Caribbean, Amazonian), (Paranaense, Atlantic))))). This sequence of area relationships is congruent with the history previously hypothesized for the subregion, where the development of an open vegetated diagonal (comprising the Chacoan, Cerrado, and Caatinga provinces) due to the aridification induced by the gradual uplift of the Andes, separated the former Amazonian forest in a northwestern part (Caribbean plus Amazonian provinces) and a southeastern part (Paranaense plus Atlantic provinces).

Description: Two new species of the genus Bentonia van Achterberg, 1992 (Braconidae: Orgilinae) (B. inca from Peru and B. xochiquetzalis from Mexico) are described and partly illustrated. A third undescribed species was found for which some characters are listed. The distribution of B. scutellaris van Achterberg, 1992, is extended west to Peru and B. longicornis van Achterberg, 1992, north to Venezuela. An identification key is added.

Description: The NPARC Alliance is a partnership between the NASA Lewis Research Center (LeRC) and the USAF Arnold Engineering Development Center (AEDC) dedicated to the establishment of a national CFD capability, centered on the NPARC Navier-Stokes computer program. The three main tasks of the Alliance are user support, code development, and validation. The present paper is a status report on the validation effort. It describes the validation approach being taken by the Alliance. Representative results are presented for laminar and turbulent flat plate boundary layers, a supersonic axisymmetric jet, and a glancing shock/turbulent boundary layer interaction. Cases scheduled to be run in the future are also listed. The archive of validation cases is described, including information on how to access it via the Internet.

Description: We study the onset of a pure Marangoni convection in a liquid layer with two deformable interfaces in the no-gravity environment. Both oscillatory and stationary instabilities are considered for a wide range of parameters. It is shown that only stationary instability is possible when surface tension at the colder interface is lower than that at the hotter one. Oscillatory instability tends to disappear and to be replaced by the stationary instability with increase of the Prandtl number and decrease of surface tension at the colder interface.

Description: A consistent solution of the radiative transfer equation characterizing photon transport in a semi-infinite medium of refractive index greater than or equal to one is obtained following the method of Sobolev. Fresnel specular reflection, Snell's law and isotropic scattering are assumed. An algorithm is developed and its accuracy is demonstrated. A numerical Laplace transform inversion leads to an efficient evaluation for the interior flux and source function distributions.

Description: Results are reported of the Surface Tension Driven Convection Experiment (STDCE) aboard USML-1 Spacelab. Steady and transient thermocapillary flows were investigated in a 10 cm dia. circular container filled with 10 Cs silicone oil. The velocity and temperature fields were studied in detail under various conditions. It is shown in this paper how the Marangoni number affects the velocity field. A numerical analysis of the flows was also conducted and its results were compared to the experimental data. Good agreement is shown.

Description: Eleven tests were carried out in DLR's high enthalpy tunnel in Goettingen (HEG), Germany, for reservoir conditions ranging from 10 to 23 MJ/kg and a free stream Mach number of approximately 10. A blunted cone model with a cylindrical afterbody (sting) was investigated. To obtain information on the influence of defined parameters on the body back flow, especially of the reacting gas, the heat transfer rate along the body contour was measured with fast response surface thermocouples on the forebody and sensitive thin film heat transfer gauges on the base and sting of the model. Flow visualization with a holographic interferometry system was provided. Tests are described, and a preliminary interpretation of the observed flow effects are given.

Description: Get Away Special (GAS) payload G-093, also called VORTEX (VOrtex Ring Transit EXperiment), is an investigation of the propagation of a vortex ring through a liquid-gas interface in microgravity. This process results in the formation of one or more liquid droplets similar to earth based liquid atomization systems. In the absence of gravity, surface tension effects dominate the drop formation process. The Shuttle's microgravity environment allows the study of the same fluid atomization processes as using a larger drop size than is possible on Earth. This enables detailed experimental studies of the complex flow processes encountered in liquid atomization systems. With VORTEX, deformations in both the vortex ring and the fluid surface will be measured closely for the first time in a parameters range that accurately resembles liquid atomization. The experimental apparatus will record images of the interactions for analysis after the payload has been returned to earth. The current design of the VORTEX payload consists of a fluid test cell with a vortex ring generator, digital imaging system, laser illumination system, computer based controller, batteries for payload power, and an array of housekeeping and payload monitoring sensors. It is a self-contained experiment and will be flown on board the Space Shuttle in a 5 cubic feet GAS canister. The VORTEX Project is entirely run by students at the University of Michigan but is overseen by a faculty advisor acting as the payload customer and the contact person with NASA. This paper summarizes both the technical and programmatic aspects of the VORTEX Project.

Description: This paper focuses on the flight results of the Cryogenic Two-Phase Flight Experiment (CRYOTP), which was a Hitchhiker based experiment that flew on the space shuttle Columbia in March of 1994 (STS-62). CRYOTP tested two new technologies for advanced cryogenic thermal control; the Space Heat Pipe (SHP), which was a constant conductance cryogenic heat pipe, and the Brilliant Eyes Thermal Storage Unit (BETSU), which was a cryogenic phase-change thermal storage device. These two devices were tested independently during the mission. Analysis of the flight data indicated that the SHP was unable to start in either of two attempts, for reasons related to the fluid charge, parasitic heat leaks, and cryocooler capacity. The BETSU test article was successfully operated with more than 250 hours of on-orbit testing including several cooldown cycles and 56 freeze/thaw cycles. Some degradation was observed with the five tactical cryocoolers used as thermal sinks, and one of the cryocoolers failed completely after 331 hours of operation. Post-flight analysis indicated that this problem was most likely due to failure of an electrical controller internal to the unit.

Description: The Capillary Pumped Loop Flight Experiment (CAPL) employs a passive two-phase thermal control system that uses the latent heat of vaporization of ammonia to transfer heat over long distances. CAPL was designed as a prototype of the Earth Observing System (EOS) instrument thermal control systems. The purpose of the mission was to provide validation of the system performance in micro-gravity, prior to implementation on EOS. CAPL was flown on STS-60 in February, 1994, with some unexpected results related to gravitational effects on two-phase systems. Flight test results and post flight investigations will be addressed, along with a brief description of the experiment design.

Description: This paper presents an overview of the Cryogenic Test Bed (CTB) experiments including experiment results, integration techniques used, and lessons learned during integration, test and flight phases of the Cryogenic Heat Pipe Flight Experiment (STS-53) and the Cryogenic Two Phase Flight Experiment (OAST-2, STS-62). We will also discuss the Cryogenic Flexible Diode Heat Pipe (CRYOFD) experiment which will fly in the 1996/97 time frame and the fourth flight of the CTB which will fly in the 1997/98 time frame. The two missions tested two oxygen axially grooved heat pipes, a nitrogen fibrous wick heat pipe and a 2-methylpentane phase change material thermal storage unit. Techniques were found for solving problems with vibration from the cryo-collers transmitted through the compressors and the cold heads, and mounting the heat pipe without introducing parasitic heat leaks. A thermally conductive interface material was selected that would meet the requirements and perform over the temperature range of 55 to 300 K. Problems are discussed with the bi-metallic thermostats used for heater circuit protection and the S-Glass suspension straps originally used to secure the BETSU PCM in the CRYOTP mission. Flight results will be compared to 1-g test results and differences will be discussed.

Description: With the recent focus on the needs of design and applications CFD, research groups have begun to address the traditional bottlenecks of grid generation and surface modeling. Now, a host of emerging technologies promise to shortcut or dramatically simplify the simulation process. This paper discusses the current status of these emerging technologies. It will argue that some tools are already available which can have positive impact on portions of the design cycle. However, in most cases, these tools need to be integrated into specific engineering systems and process cycles to be used effectively. The rapidly maturing status of unstructured and Cartesian approaches for inviscid simulations makes suggests the possibility of highly automated Euler-boundary layer simulations with application to loads estimation and even preliminary design. Similarly, technology is available to link block structured mesh generation algorithms with topology libraries to avoid tedious re-meshing of topologically similar configurations. Work in algorithmic based auto-blocking suggests that domain decomposition and point placement operations in multi-block mesh generation may be properly posed as problems in Computational Geometry, and following this approach may lead to robust algorithmic processes for automatic mesh generation.

Description: The last decade has witnessed a vigorous and sustained research effort on unstructured methods for computational fluid dynamics. Unstructured mesh generators and flow solvers have evolved to the point where they are now in use for design purposes throughout the aerospace industry. In this paper we survey the various mesh types, structured as well as unstructured, and examine their relative strengths and weaknesses. We argue that unstructured methodology does offer the best prospect for the next generation of computational fluid dynamics algorithms.

Description: A Cartesian, cell-based approach for adaptively-refined solutions of the Euler and Navier-Stokes equations in two dimensions is developed and tested. Grids about geometrically complicated bodies are generated automatically, by recursive subdivision of a single Cartesian cell encompassing the entire flow domain. Where the resulting cells intersect bodies, N-sided 'cut' cells are created using polygon-clipping algorithms. The grid is stored in a binary-tree data structure which provides a natural means of obtaining cell-to-cell connectivity and of carrying out solution-adaptive mesh refinement. The Euler and Navier-Stokes equations are solved on the resulting grids using a finite-volume formulation. The convective terms are upwinded: A gradient-limited, linear reconstruction of the primitive variables is performed, providing input states to an approximate Riemann solver for computing the fluxes between neighboring cells. The more robust of a series of viscous flux functions is used to provide the viscous fluxes at the cell interfaces. Adaptively-refined solutions of the Navier-Stokes equations using the Cartesian, cell-based approach are obtained and compared to theory, experiment and other accepted computational results for a series of low and moderate Reynolds number flows.

Description: Grid related issues of the Chimera overset grid method are discussed in the context of a method of solution and analysis of unsteady three-dimensional viscous flows. The state of maturity of the various pieces of support software required to use the approach is considered. Current limitations of the approach are identified.

Description: This paper presents 'A view from the trenches' on CFD grid generation from a Pratt & Whitney perspective. We anticipate that other organizations have similar views. We focus on customer expectations and the consequent requirements. We enunciate a vision for grid generation, discuss issues that developers must recognize.

Description: This paper presents a perspective on the requirements that Computational Fluid Dynamics (CFD) technology must meet for its effective use in aerospace design. General observations are made on current aerospace design practices and deficiencies are noted that must be rectified for the U.S. aerospace industry to maintain its leadership position in the global marketplace. In order to rectify deficiencies, industry is transitioning to an integrated product and process development (IPPD) environment and design processes are undergoing radical changes. The role of CFD in producing data that design teams need to support flight vehicle development is briefly discussed. An overview of the current state of the art in CFD is given to provide an assessment of strengths and weaknesses of the variety of methods currently available, or under development, to produce aerodynamic data. Effectiveness requirements are examined from a customer/supplier view point with design team as customer and CFD practitioner as supplier. Partnership between the design team and CFD team is identified as an essential requirement for effective use of CFD. Rapid turnaround, reliable accuracy, and affordability are offered as three key requirements that CFD community must address if CFD is to play its rightful role in supporting the IPPD design environment needed to produce high quality yet affordable designs.

Description: The efforts in geometry modeling and grid generation at the NASA Lewis Research Center, as applied to the computational fluid dynamic (CFD) analysis of aeropropulsion systems, are presented. The efforts are mainly characterized by a focus on the analysis of components of an aeropropulsion system, which involve turbulent viscous flow with heat transfer and chemistry. Thus, this discussion will follow that characterization and will sequence through the components of typical propulsion systems consisting of inlets, compressors, combustors, turbines, and nozzles. For each component, some applications of CFD analysis will be presented to show how CFD is used to compute the desired performance information, how geometry modeling and grid generation are performed, and what issues have developed related to geometry modeling and grid generation. The discussion will illustrate the following needs related to geometry modeling and grid generation as observed in aeropropulsion analysis: (1) accurate and efficient resolution of turbulent viscous and chemically-reacting flowfields; (2) easy-to-use interfaces with CAD data for automated grid generation about complex geometries; and (3) automated batch grid generation software for use with design and optimization software.

Description: This viewgraph presentation discusses key features of current combustion system CFD modeling capabilities at GE Aircraft Engines provided by the CONCERT code; CONCERT development history; modeling applied for designing engine combustion systems; modeling applied to improve fundamental understanding; CONCERT3D results for current production combustors; CONCERT3D model of NASA/GE E3 combustor; HYBRID CONCERT CFD/Monte-Carlo modeling approach; and future modeling directions.

Description: A procedure was developed to improve the turn-around time for computational fluid dynamics (CFD) simulations of an inlet-bleed problem involving oblique shock-wave/boundary-layer interactions on a flat plate with bleed into a plenum through one or more circular holes. This procedure is embodied in a preprocessor called AUTOMAT. With AUTOMAT, once data for the geometry and flow conditions have been specified (either interactively or via a namelist), it will automatically generate all input files needed to perform a three-dimensional Navier-Stokes simulation of the prescribed inlet-bleed problem by using the PEGASUS and OVERFLOW codes. The input files automatically generated by AUTOMAT include those for the grid system and those for the initial and boundary conditions. The grid systems automatically generated by AUTOMAT are multi-block structured grids of the overlapping type. Results obtained by using AUTOMAT are presented to illustrate its capability.

Description: The role of Computational Fluid Dynamics (CFD) at Ames Research Center has expanded to address a broad range of aeronautical problems, including wind tunnel support, flight test support, design, and analysis. Balancing the requirements of each new problem against the available resources - software, hardware, time, and expertise - is critical to the effective use of CFD. Several case studies of recent applications highlight the depth of CFD capability at Ames, the tradeoffs involved in various approaches, and lessons learned in the use of CFD as an engineering tool.

Description: When computing the flow around complex three dimensional configurations, the generation of the mesh is the most time consuming part of any calculation. With some meshing technologies this can take of the order of a man month or more. The requirement for a number of design iterations coupled with ever decreasing time allocated for design leads to the need for a significant acceleration of this process. Of the two competing approaches, block-structured and unstructured, only the unstructured approach will allow fully automatic mesh generation directly from a CAD model. Using this approach coupled with the techniques described in this paper, it is possible to reduce the mesh generation time from man months to a few hours on a workstation. The desire to closely couple a CFD code with a design or optimization algorithm requires that the changes to the geometry be performed quickly and in a smooth manner. This need for smoothness necessitates the use of Bezier polynomials in place of the more usual NURBS or cubic splines. A two dimensional Bezier polynomial based design system is described.

Description: The results of a first order perfect gas correction for the effects of the boundary layer formation within expansion tubes with nozzles are presented. The analytical model developed to describe the boundary layer formation within the expansion tube and an expansion nozzle located at the end of the acceleration tube is based on the Karman integral equations. The results of this analytical model are compared with experimental data from an expansion diffuser. The model provides a useful tool for the preliminary design of nozzles for such facilities.

Description: In this paper the capabilities of an automated CFD system which is currently available at NLR are demonstrated. Transonic flow around the AS28G wing/body configuration and hypersonic flow through a generic three-dimensional mixed-compression airbreathing inlet are simulated. An assessment of the level of automation of the current CFD-system is made. The problem-turnaround time lies within the order of a week for both applications.

Description: Detailed simulations of viscous flows in complicated geometries pose a significant challenge to current capabilities of Computational Fluid Dynamics (CFD). To enable routine application of CFD to this class of problems, advanced methodologies are required that employ (a) automated grid generation, (b) adaptivity, (c) accurate discretizations and efficient solvers, and (d) advanced software techniques. Each of these ingredients contributes to increased accuracy, efficiency (in terms of human effort and computer time), and/or reliability of CFD software. In the long run, methodologies employing structured grid systems will remain a viable choice for routine simulation of flows in complex geometries only if genuinely automatic grid generation techniques for structured grids can be developed and if adaptivity is employed more routinely. More research in both these areas is urgently needed.

Description: A discussion of the strengths and weaknesses of overset composite grid and solution technology is given, along with a sampling of current work in the area. Major trends are identified, and the observation is made that generalized and hybridized overset methods provide a natural framework for combining disparate mesh types and physics models. Because of this, the author concludes that overset methods will be the foundation for the general purpose computational fluid dynamics programs of the future.

Description: The status of CFD methods based on the use of block-structured grids for analyzing viscous flows over complex configurations is examined. The objective of the present study is to make a realistic assessment of the usability of such grids for routine computations typically encountered in the aerospace industry. It is recognized at the very outset that the total turnaround time, from the moment the configuration is identified until the computational results have been obtained and postprocessed, is more important than just the computational time. Pertinent examples will be cited to demonstrate the feasibility of solving flow over practical configurations of current interest on block-structured grids.

Description: This viewgraph presentation discusses turbulence modeling requirements, development philosophy, and approach; two major areas of concentration (high speed and low speed turbulence modeling); high speed turbulence modeling; compressibility effects; turbulence models adapted to USA code; M = 9.2 flat plate flow; Mach 7.05 flow over axisymmetric flare; Mach 8.6 flow over cold wall edge; low speed turbulence modeling; turbulence models being assessed; turbulence model deck structure and integration with Navier-Stokes solver; nonlinear algebraic-stress model; rotation modified k-epsilon model; and Reynolds stress model.

Description: This viewgraph presentation covers gas turbine combustor flow physics, turbulence model investigations, turbulent combustion modeling, and present status and future needs.

Description: This viewgraph presentation discusses geometry and flow configuration, effect of y+ on heat transfer computations, standard and extended k-epsilon turbulence model results with wall function, low-Re model results (the Lam-Bremhorst model without wall function), a criterion for flow reversal in a radially rotating square duct, and a summary.

Description: This viewgraph presentation demonstrates that computationally efficient k-l and k-kl turbulence models have been developed and implemented at Lockheed Fort Worth Company. Many years of experience have been gained applying two equation turbulence models to complex three-dimensional flows for design and analysis.

Description: The objective of this viewgraph presentation is to evaluate turbulence models for integrated aircraft components such as the forebody, wing, inlet, diffuser, nozzle, and afterbody. The one-equation models have replaced the algebraic models as the baseline turbulence models. The Spalart-Allmaras one-equation model consistently performs better than the Baldwin-Barth model, particularly in the log-layer and free shear layers. Also, the Sparlart-Allmaras model is not grid dependent like the Baldwin-Barth model. No general turbulence model exists for all engineering applications. The Spalart-Allmaras one-equation model and the Chien k-epsilon models are the preferred turbulence models. Although the two-equation models often better predict the flow field, they may take from two to five times the CPU time. Future directions are in further benchmarking the Menter blended k-w/k-epsilon and algorithmic improvements to reduce CPU time of the two-equation model.

Description: This viewgraph presentation summarizes some CFD experience at GE Aircraft Engines for flows in the primary gaspath of a gas turbine engine and in turbine blade cooling passages. It is concluded that application of the standard k-epsilon turbulence model with wall functions is not adequate for accurate CFD simulation of aerodynamic performance and heat transfer in the primary gas path of a gas turbine engine. New models are required in the near-wall region which include more physics than wall functions. The two-layer modeling approach appears attractive because of its computational complexity. In addition, improved CFD simulation of film cooling and turbine blade internal cooling passages will require anisotropic turbulence models. New turbulence models must be practical in order to have a significant impact on the engine design process. A coordinated turbulence modeling effort between NASA centers would be beneficial to the gas turbine industry.

Description: Program goals at the Center for Modeling of Turbulence and Transition (CMOTT), NASA Lewis Research Center, are (1) to develop reliable turbulence (including bypass transition) and combustion models for complex flows in propulsion systems and (2) to integrate developed models into deliverable CFD tools for propulsion systems in collaboration with industry. This viewgraph presentation covers the following topics: development of turbulence and combustion models; collaboration with industry and technology transfer; isotropic eddy viscosity models; algebraic Reynolds stress models; scalar turbulence models; second order closure models; multiple scale k-epsilon models; and PDF modeling of turbulent reacting flows.

Description: An assessment of two unstructured methods is presented in this paper. A tetrahedral unstructured method USM3D, developed at NASA Langley Research Center is compared to a Cartesian unstructured method, SPLITFLOW, developed at Lockheed Fort Worth Company. USM3D is an upwind finite volume solver that accepts grids generated primarily from the Vgrid grid generator. SPLITFLOW combines an unstructured grid generator with an implicit flow solver in one package. Both methods are exercised on three test cases, a wing, and a wing body, and a fully expanded nozzle. The results for the first two runs are included here and compared to the structured grid method TEAM and to available test data. On each test case, the set up procedure are described, including any difficulties that were encountered. Detailed descriptions of the solvers are not included in this paper.

Description: The past ten years have seen steady progress in surface modeling procedures, and wholesale changes in grid generation technology. Today, it seems fair to state that a satisfactory grid can be developed to model nearly any configuration of interest. The issues at present focus on operational concerns such as cost and quality. Continuing evolution of the engineering process is placing new demands on the technologies of surface modeling and grid generation. In the evolution toward a multidisciplinary analysis-bascd design environment, methods developed for Computational Fluid Dynamics are finding acceptance in many additional applications. These two trends, the normal evolution of the process and a watershed shift toward concurrent and multidisciplinary analysis, will be considered in assessing current capabilities and needed technological improvements.

Description: This viewgraph presentation discusses what models are used in this package and what their advantages and disadvantages are, how the probability density function (PDF) model is implemented and the features of the program, and what can be expected in the future from the NASA Lewis PDF code.

Description: This viewgraph presentation discusses an extension of the probability density function (PDF) method to the modeling of spray flames to evaluate the limitations and capabilities of this method in the modeling of gas-turbine combustor flows. The comparisons show that the general features of the flowfield are correctly predicted by the present solution procedure. The present solution appears to provide a better representation of the temperature field, particularly, in the reverse-velocity zone. The overpredictions in the centerline velocity could be attributed to the following reasons: (1) the use of k-epsilon turbulence model is known to be less precise in highly swirling flows and (2) the swirl number used here is reported to be estimated rather than measured.

Description: Viewgraphs are presented on computation of turbulent combustion, governing equations, closure problem, PDF modeling of turbulent reactive flows, validation cases, current projects, and collaboration with industry and technology transfer.

Description: Viewgraphs are presented on modeling turbulent reacting flows, regimes of turbulent combustion, regimes of premixed and regimes of non-premixed turbulent combustion, chemical closure models, flamelet model, conditional moment closure (CMC), NO(x) emissions from turbulent H2 jet flames, probability density function (PDF), departures from chemical equilibrium, mixing models for PDF methods, comparison of predicted and measured H2O mass fractions in turbulent nonpremixed jet flames, experimental evidence of preferential diffusion in turbulent jet flames, and computation of turbulent reacting flows.

Description: This viewgraph presentation discusses project description, turbulence models, and computational engine and results for second-order closures for compressible turbulence.

Description: This viewgraph presentation gives a profile of Advanced Scientific Computing (ASC) Ltd., applications, clients and clients' needs, ASC's directions, and how the Center for Modeling of Turbulence and Transition (CMOTT) can help.

Description: This viewgraph presentation discusses the following: STAR-CD computational features; STAR-CD turbulence models; common features of industrial complex flows; industry-specific CFD development requirements; applications and experiences of industrial complex flows, including flow in rotating disc cavities, diffusion hole film cooling, internal blade cooling, and external car aerodynamics; and conclusions on turbulence modeling needs.

Description: This viewgraph presentation provides a brief review of two-equation eddy-viscosity models (TEM's) from the perspective of applied CFD. It provides objective assessment of both well-known and newer models, compares model predictions from various TEM's with experiments, identifies sources of modeling error and gives historical perspective of their effects on model performance and assessment, and recommends directions for future research on TEM's.

Description: This viewgraph presentation discusses the following: introduction to CFD Research Corporation; experiences with two-equation models - models used, numerical difficulties, validation and applications, and strengths and weaknesses; and answers to three questions posed by the workshop organizing committee - what are your customers telling you, what are you doing in-house, and how can NASA-CMOTT (Center for Modeling of Turbulence and Transition) help.

Description: This viewgraph presentation concludes that a Monte Carlo probability density function (PDF) solution successfully couples with an existing finite volume code; PDF solution method applied to turbulent reacting flows shows good agreement with data; and PDF methods must be run on parallel machines for practical use.

Description: This viewgraph presentation discusses (1) turbulence modeling: challenges in turbulence modeling, desirable attributes of turbulence models, turbulence models in FLUENT, and examples using FLUENT; and (2) combustion modeling: turbulence-chemistry interaction and FLUENT equilibrium model. As of now, three turbulence models are provided: the conventional k-epsilon model, the renormalization group model, and the Reynolds-stress model. The renormalization group k-epsilon model has broadened the range of applicability of two-equation turbulence models. The Reynolds-stress model has proved useful for strongly anisotropic flows such as those encountered in cyclones, swirlers, and combustors. Issues remain, such as near-wall closure, with all classes of models.

Description: This viewgraph presentation discusses joint velocity-scalar PDF method; turbulent combustion modeling issues for gas turbine combustors; PDF calculations for a recirculating flow; stochastic dissipation model; joint PDF calculations for swirling flows; spray calculations; reduced kinetics/manifold methods; parallel processing; and joint PDF focus areas.

Description: An algorithm has been developed for time-dependent forced convective diffusion-reaction having convection by a recirculating flow field within the drop that is hydrodynamically coupled at the interface with a convective external flow field that at infinity becomes a uniform free-streaming flow. The concentration field inside the droplet is likewise coupled with that outside by boundary conditions at the interface. A chemical reaction can take place either inside or outside the droplet, or reactions can take place in both phases. The algorithm has been implemented, and for comparison results are shown here for the case of no reaction in either phase and for the case of an external first order reaction, both for unsteady behavior. For pure interphase mass transfer, concentration isocontours, local and average Sherwood numbers, and average droplet concentrations have been obtained as a function of the physical properties and external flow field. For mass transfer enhanced by an external reaction, in addition to the above forms of results, we present the enhancement factor, with the results now also depending upon the (dimensionless) rate of reaction.

Description: The application of spectral methods, using a Chebyshev collocation scheme, to solve hydrodynamic stability problems is demonstrated on the Benard problem. Implementation of the Chebyshev collocation formulation is described. The performance of the spectral scheme is compared with that of a 2nd order finite difference scheme. An exact solution to the Marangoni-Benard problem is used to evaluate the performance of both schemes. The error of the spectral scheme is at least seven orders of magnitude smaller than finite difference error for a grid resolution of N = 15 (number of points used). The performance of the spectral formulation far exceeded the performance of the finite difference formulation for this problem. The spectral scheme required only slightly more effort to set up than the 2nd order finite difference scheme. This suggests that the spectral scheme may actually be faster to implement than higher order finite difference schemes.

Description: The effects of different turbulence boundary conditions were examined for two classical flows: a turbulent plane free shear layer and a flat plate turbulent boundary layer with zero pressure gradient. The flow solver used was DTNS, an incompressible Reynolds averaged Navier-Stokes solver with k-epsilon turbulence modeling, developed at the U.S. Navy David Taylor Research Center. Six different combinations of turbulence boundary conditions at the inflow boundary were investigated: In case 1, 'exact' k and epsilon profiles were used; in case 2, the 'exact' k profile was used, and epsilon was extrapolated upstream; in case 3, both k and epsilon were extrapolated; in case 4, the turbulence intensity (I) was 1 percent, and the turbulent viscosity (mu(sub t)) was equal to the laminar viscosity; in case 5, the 'exact' k profile was used and mu(sub t) was equal to the laminar viscosity; in case 6, the I was 1 percent, and epsilon was extrapolated. Comparisons were made with experimental data, direct numerical simulation results, or theoretical predictions as applicable. Results obtained with DTNS showed that turbulence boundary conditions can have significant impacts on the solutions, especially for the free shear layer.

Description: The exchange of models is one of the most serious problems currently encountered in the practice of spacecraft thermal analysis. Essentially, the problem originates in the diversity of computing environments that are used across different sites, and the consequent proliferation of native tool formats. Furthermore, increasing pressure to reduce the development's life cycle time has originated a growing interest in the so-called spacecraft concurrent engineering. In this context, the realization of the interdependencies between different disciplines and the proper communication between them become critical issues. The use of a neutral format represents a step forward in addressing these problems. Such a means of communication is adopted by consensus. A neutral format is not directly tied to any specific tool and it is kept under stringent change control. Currently, most of the groups promoting exchange formats are contributing with their experience to STEP, the Standard for Exchange of Product Model Data, which is being developed under the auspices of the International Standards Organization (ISO 10303). This paper presents the different efforts made in Europe to provide the spacecraft thermal analysis community with a Thermal Neutral Format (TNF) based on STEP. Following an introduction with some background information, the paper presents the characteristics of the STEP standard. Later, the first efforts to produce a STEP Spacecraft Thermal Application Protocol are described. Finally, the paper presents the currently harmonized European activities that follow up and extend earlier work on the area.

Description: Using global interpolation functions (GIF's) boundary element solutions are obtained for two-dimensional laminar flows. Two schemes are proposed for handling the convective terms. The first treats convection as a forcing function, and converts the flow equations to pseudo-Poisson equations. In the second scheme, some convective effect is incorporated into the fundamental solution used in constructing the pertinent integral equations. The lid-driven cavity flow is selected as the benchmark problem.

Description: A two dimensional finite volume method is used to predict the film coefficients in the transitional flow region (laminar or turbulent) for the radiator panel tubes. The code used to perform this analysis is CAST (Computer Aided Simulation of Turbulent Flows). The information gathered from this code is then used to augment a Sinda85 model that predicts overall performance of the radiator. A final comparison is drawn between the results generated with a Sinda85 model using the Sinda85 provided transition region heat transfer correlations and the Sinda85 model using the CAST generated data.

Description: This paper presents a probabilistic one-dimensional finite element model for heat transfer processes in porous heat exchangers. The Galerkin approach is used to develop the finite element matrices. Some of the submatrices are asymmetric due to the presence of the flow term. The Neumann expansion is used to write the temperature distribution as a series of random variables, and the expectation operator is applied to obtain the mean and deviation statistics. To demonstrate the feasibility of the formulation, a one-dimensional model of heat transfer phenomenon in superfluid flow through a porous media is considered. Results of this formulation agree well with the Monte-Carlo simulations and the analytical solutions. Although the numerical experiments are confined to parametric random variables, a formulation is presented to account for the random spatial variations.

Description: This paper presents a numerical scheme, based on the finite element method, to solve strongly coupled fluid flow and heat transfer problems. The surface radiation effect for gray, diffuse and isothermal surfaces is considered. A procedure for obtaining the view factors between the radiating surfaces is discussed. The overall solution strategy is verified by comparing the available results with those obtained using this approach. An analysis of a thermosyphon is undertaken and the effect of considering the surface radiation is clearly explained.

Description: An algorithm has been developed for the forced convective diffusion-reaction problem for convection inside and outside a droplet by a recirculating flow field hydrodynamically coupled at the droplet interface with an external flow field that at infinity becomes a uniform streaming flow. The concentration field inside the droplet is likewise coupled with that outside by boundary conditions at the interface. A chemical reaction can take place either inside or outside the droplet or reactions can take place in both phases. The algorithm has been implemented and results are shown here for the case of no reaction and for the case of an external first order reaction, both for unsteady behavior. For pure interphase mass transfer, concentration isocontours, local and average Sherwood numbers, and average droplet concentrations have been obtained as a function of the physical properties and external flow field. For mass transfer enhanced by an external reaction, in addition to the above forms of results, we present the enhancement factor, with the results now also depending upon the (dimensionless) rate of reaction.

Description: The critical state of vortex cores downstream of vortex breakdown has been studied. Base vortical flows were computed using the Reynolds-averaged, axisymmetric Navier-Stokes equations. Standard K - epsilon, RNG and second-order Reynolds stress models were employed. Results indicate that the return to supercriticality is highly dependent on the turbulence model. The K - epsilon model predicted a rapid return of the vortex to supercritical conditions, the location of which showed little sensitivity to changes in the swirl ratio. The Reynolds stress model predicted that the vortex remains subcritical to the end of the domain for each of the swirl ratios employed, and provided results in qualitative agreement with experimental work. The RNG model produced intermediate results, with a downstream movement in the critical location with increasing swirl. Calculations for which area reductions were introduced at the exit in a subcritical flow were also performed using the Reynolds stress model. The structure of the resulting recirculation zone was altered significantly. However, when area reductions were employed within supercritical flows as predicted using the two-equation models, no significant influence on the recirculation zone was noted.