ALBERT

Description: The first 18 tracks of laser altimeter data across the northern hemisphere of Mars from the Mars Global Surveyor spacecraft show that the planet at latitudes north of 50 degrees is exceptionally flat; slopes and surface roughness increase toward the equator. The polar layered terrain appears to be a thick ice-rich formation with a non-equilibrium planform indicative of ablation near the periphery. Slope relations suggest that the northern Tharsis province was uplifted in the past. A profile across Ares Vallis channel suggests that the discharge through the channel was much greater than previously estimated. The martian atmosphere shows significant 1-micrometer atmospheric opacities, particularly in low-lying areas such as Valles Marineris.

Description: A combination of scanning electron microscopy (SEM) and environmental scanning electron microscopy (ESEM) techniques, as well as atomic force microscopy (AFM) methods has been used to study fragments of the Martian meteorite ALH84001. Images of the same areas on the meteorite were obtained prior to and following gold/palladium coating by mapping the surface of the fragment using ESEM coupled with energy-dispersive X-ray analysis. Viewing of the fragments demonstrated the presence of structures, previously described as nanofossils by McKay et al. (Search for past life on Mars--possible relic biogenic activity in martian meteorite ALH84001. Science, 1996, pp. 924-930) of NASA who used SEM imaging of gold-coated meteorite samples. Careful imaging of the fragments revealed that the observed structures were not an artefact introduced by the coating procedure.

Description: With the recent announcement of the discovery of the possibility of life on Mars, there is renewed interest in Mars missions, perhaps eventually in human missions. Astronauts on such missions are at risk to occasional periods of enhanced high energy particle flux from the sun known as Solar Particle Events. These events can pose a substantial risk to the health of the astronauts and to the on-board electronics. Effective forecast and warning of these events could provide time to take steps to minimize the risk (retreating to a safe haven, shutting down sensitive equipment, etc.) Providing that forecast capability, will require additional monitoring capability. The extent of this architecture is sensitive to the orbit selected for the transfer to and from Mars. This paper looks at the major classes of Mars missions (Conjunction and Opposition) and sub-categories of these classes and draws conclusions on the number of monitoring satellites needed for each, with a goal to reducing total system cost through optimum orbit selection.

Description: Trace amounts of glycine, serine, and alanine were detected in the carbonate component of the martian meteorite ALH84001 by high-performance liquid chromatography. The detected amino acids were not uniformly distributed in the carbonate component and ranged in concentration from 0.1 to 7 parts per million. Although the detected alanine consists primarily of the L enantiomer, low concentrations (〈0.1 parts per million) of endogenous D-alanine may be present in the ALH84001 carbonates. The amino acids present in this sample of ALH84001 appear to be terrestrial in origin and similar to those in Allan Hills ice, although the possibility cannot be ruled out that minute amounts of some amino acids such as D-alanine are preserved in the meteorite.

Description: Deuterated water (HDO) was detected in comet C/1995 O1 (Hale-Bopp) with the use of the James Clerk Maxwell Telescope on Mauna Kea, Hawaii. The inferred D/H ratio in Hale-Bopp's water is (3.3 +/- 0.8) x 10(-4). This result is consistent with in situ measurements of comet P/Halley and the value found in C/1996 B2 (Hyakutake). This D/H ratio, higher than that in terrestrial water and more than 10 times the value for protosolar H2, implies that comets cannot be the only source for the oceans on Earth.

Description: The Thermal Emission Spectrometer spectra of low albedo surface materials suggests that a four to one mixture of pyroxene to plagioclase, together with about a 35 percent dust component provides the best fit to the spectrum. Qualitative upper limits can be placed on the concentration of carbonates (〈10 percent), olivine (〈10 percent), clay minerals (〈20 percent), and quartz (〈5 percent) in the limited regions observed. Limb observations in the northern hemisphere reveal low-lying dust hazes and detached water-ice clouds at altitudes up to 55 kilometers. At an aerocentric longitude of 224 degrees a major dust storm developed in the Noachis Terra region. The south polar cap retreat was similar to that observed by Viking.

Description: Deuterated hydrogen cyanide (DCN) was detected in a comet, C/1995 O1 (Hale-Bopp), with the use of the James Clerk Maxwell Telescope on Mauna Kea, Hawaii. The inferred deuterium/hydrogen (D/H) ratio in hydrogen cyanide (HCN) is (D/H)HCN = (2.3 +/- 0.4) x 10(-3). This ratio is higher than the D/H ratio found in cometary water and supports the interstellar origin of cometary ices. The observed values of D/H in water and HCN imply a kinetic temperature 〉/=30 +/- 10 K in the fragment of interstellar cloud that formed the solar system.

Description: Radio Doppler data from a single encounter (C3) of the Galileo spacecraft with Callisto, the outermost Galilean moon of Jupiter, indicated that Callisto was probably undifferentiated. Now, similar data from a second encounter (C9) corroborate this conclusion, but more accurate data from a third encounter (C10) indicate that the rock and ice within Callisto have partially, but not completely, separated. Callisto may be differentiated into a rock-metal core less than 25 percent of Callisto's radius, an outer layer of clean ice less than 350 km thick, and a middle layer of mixed rock and ice. Models in which ice and rock are mixed all the way to the center of Callisto are also consistent with the data.

Description: High-resolution spectroscopy of Mars' atmosphere with the Hubble Space Telescope revealed the deuterium Lyman alpha line at an intensity of 23 +/- 6 rayleighs. This measured intensity corresponds to HD/H2 = 1.5 +/- 0.6 x 10(-4), which is smaller by a factor of 11 than HDO/H2O. This indicates that fractionation of HD/H2 relative to that of HDO/H2O is not kinetically controlled by the rates of formation and destruction of H2 and HD but is thermodynamically controlled by the isotope exchange HD + H2O left and right arrow HDO + H2. Molecular hydrogen is strongly depleted in deuterium relative to water on Mars because of the very long lifetime of H2 (1200 years). The derived isotope fractionation corresponds to an estimate of a planetwide reservoir of water ice about 5 meters thick that is exchangeable with the atmosphere.

Description: Spectra of the Centaur 1997 CU26 were obtained at the Keck Observatory on 27 October 1997 (universal time). The data show strong absorptions at 1.52 and 2.03 micrometers attributable to water ice on the surface of 1997 CU26. The reflectance spectrum of 1997 CU26 is matched by the spectrum of a mixture of low-temperature, particulate water ice and spectrally featureless but otherwise red-colored material. Water ice dominates the spectrum of 1997 CU26, whereas methane or methane-like hydrocarbons apparently dominate the spectrum of the Kuiper belt object 1993 SC, perhaps indicating different origins, thermal histories, or both for these two objects.

Description: The permanent ice covers of Antarctic lakes in the McMurdo Dry Valleys develop liquid water inclusions in response to solar heating of internal aeolian-derived sediments. The ice sediment particles serve as nutrient (inorganic and organic)-enriched microzones for the establishment of a physiologically and ecologically complex microbial consortium capable of contemporaneous photosynthesis, nitrogen fixation, and decomposition. The consortium is capable of physically and chemically establishing and modifying a relatively nutrient- and organic matter-enriched microbial "oasis" embedded in the lake ice cover.

Description: Radio Doppler data from four encounters of the Galileo spacecraft with the jovian moon Europa have been used to refine models of Europa's interior. Europa is most likely differentiated into a metallic core surrounded by a rock mantle and a water ice-liquid outer shell, but the data cannot eliminate the possibility of a uniform mixture of dense silicate and metal beneath the water ice-liquid shell. The size of a metallic core is uncertain because of its unknown composition, but it could be as large as about 50 percent of Europa's radius. The thickness of Europa's outer shell of water ice-liquid must lie in the range of about 80 to 170 kilometers.

Description: Voyager images reveal that three prominent clumps in Saturn's F ring were short-lived, appearing rapidly and then spreading and decaying in brightness over periods of approximately 2 weeks. These features arise from hypervelocity impacts by approximately 10-centimeter meteoroids into F ring bodies. Future ring observations of these impact events could constrain the centimeter-sized component of the meteoroid population, which is otherwise unmeasurable but plays an important role in the evolution of rings and surfaces in the outer solar system. The F ring's numerous other clumps are much longer lived and appear to be unrelated to impacts.

Description: Significant gas-phase chemistry occurs in the comae of bright comets, as is demonstrated here for the case of Comet Hale-Bopp. The abundance ratio of the two isomers, hydrogen cyanide and hydrogen isocyanide, is shown to vary with heliocentric distance in a way that is consistent with production of HNC by ion-molecule chemistry initiated by the photoionization of water. Likewise, the first maps of emission from HCO+ show an abundance and an extended distribution that are consistent with the same chemical model.

Description: Direct indicators of shorelines, spillways, and terraces allowed to determine the extent of the Elysium Paleolake between the contour-lines 1000 and 500 m below the Martian datum. The Elysium Paleolake is bordered north by Orcus Patera (14N/181W), which lies west of the Tartarus Montes and Tartarus Colles. The Orcus Patera displays an ellipse-shaped collapsed caldera of 360-km long and 100-km wide. Viking topographic data show that the bottom of the caldera is located at 2500 below the Martian datum, and surrounded by a steep-walled ram art which crest is located at about 0 m elevation. Considering the localization of Orcus Patera in the Elysium paleolake, its altimetry, and the magmatic origin of this caldera, we propose the existence of a paleolake in Orcus Patera generated (a) by juvenile water from magma during the Noachian period, and (b) by intermittent influx of the Elysium Basin from Hesperian to Amazonian. Results are encouraging to consider this site as a potential high-energy source environment for microbial communities. are circumscribed by a 50-km wide lava field mapped as Noachian material. The structure of Orcus Patera represents the record of material erupted from a magmatic reservoir. The caldera is enclosed by steep inner walls (25% measured from topographic data), values which could be in agreement with the presence of a deep magmatic reservoir, as suggested by the typology of Crumpler et.al. The depth of the caldera might be due to the collapse of the magma reservoir, and the release of gases accompanying the magma thermal evolution. Origins of water for the paleolake(s): The water that generated a paleolake in Orcus Patera may have come from two origins: (1) Juvenile water: Plescia and Crips estimated a magma H20 content by weight between 0.5% and 1.5% using for the first value a comparison with terrestrial basalt, and for the second values from a Martian meteorite. The amount of H20 can be estimated by the volume of erupted lava, and the lava content of the caldera. In this study, we adopt a water content of 1%. The total volume of magma that has been contained in the caldera, and the volume of lava contained in the observed lava field is about 110 x 10(exp 6) cubic km, that gives a total volume of 1.10 x 10(exp 6) cubic km of water. The juvenile water expelled by the overpressure within the magma chamber charged with desolved water-vapor may have moved into the crust. The decrease in overburden pressure led to bubble formation. The ascent of these bubbles generated a pressurization of the magma, which was sufficient to fracture the overlaying magma layer, (2) Water from Elysium paleolake. During the Amazonian, the rise of the Elysium paleolake level generated an overspilling that supplied the caldera with water. The southern portion of the crest shows a deep gap 12-km wide at -1500 m elevation, locating the gap between 500 to 1000 in below the assumed water of Elysium paleolake, thus facilitating the influx of Elysium paleolake water into Orcus Patera. Bathymetric calculations give a floor area of 25,500 sq km at -2000 m elevation, and a water volume of 42,000 cubic km, with a lake-level at -1500 m. A substantial amount of water may have percolated through the fractured lava, and part of the volume may have overspilled the northern crest of Orcus Patera to debouch in the Tartarus Montes region. We envision the formation of a subsurface aqueous environment in basaltic rocks at the contact of the two water-source origins, possibly the percolating surface lake water, and more likely the juvenile water. Similarly to terrestrial calderas, Orcus Patera might be surrounded by ring-fractures caused by the collapse of the magma chamber that followed the release of gases. These ring-fractures may have been covered later by sedimentation in the caldera (lacustrine, aeolian, and volcanic), and by mass wasting. The detumescence of the magma in the caldera, and the vesiculation of the juvenile water may have operated simultaneously. Comparatively to terrestrial melts, Martian iron-rich melts are denser. This greater density implies greater effusion rates (eight-times terrestrial values), and larger fissuration widths (two-times terrestrial ones). With increasing vesiculation of magma, the bubbles interact with one-another because there are of similar pressure. They make a magma froth at the contact with the caldera surface, and on the walls of the fractures. In the saturated magma, froth, where the volume ratio of gases-to-liquid is about 4:1, the bubbles form a huge surface area of interconnected spaces. Bubbles near the caldera surface disrupt the magma, and fragmentation takes place, which moves downward through the magma column. On Earth, the bubbles are likely to grow between 1 and 50 mm in diameter due to the difference between the magma surface tension, and the bubble supersaturation pressure. The Martian low-pressure at surface level is likely to accelerate the expansion of the bubbles, and increase their final diameter and number, creating more voids in the magma. The strong magma froth with enclosed juvenile water bubbles interconnected with exsolved gas bubbles constitute a potential geothermal environment for geochemical energy production from basalt and water that does not require excessive temperatures. This process can start at +20C. Similar types of environments have been shown on Earth as potential energy sources for microbial metabolism, and could have provided deep aqueous basaltic niches for possible Martian microorganisms, even geologically recently. During the Amazonian, combination of volcanism and water activity still existed on Mars. Moreover, this type of potential niches open ways for investigation of possible oases of extinct or extant life, not only on paleolakes, and surface hydrothermalism spring areas, but also all large systems of fossae, which combine hydrologic and volcanic activities, and which provide an energy source, and an underground shelter to prevent surface UV bombardment. Additional information contained in the original.

Description: This document is intended to provide the Mars Surveyor 2001 Project Science Group (PSG) with an overview of all the significant impacts of landing site location on the flight system, mission design, and science return. In order to facilitate the design of the Rover and Lander systems, the Project has requested that the PSG select a 15 latitude band within the 15S to 30N region, at the site selection workshop to be held at NASA Ames Research Center on January 26-27, 1998.

Description: Our objective is to propose two landing sites that the Mars Surveyor 2001 Lander and Athena Rover could go to on Mars that should meet the safety requirements of the spacecraft landing system and optimize surface operations (chiefly driven by power and communications requirements). An additional site within Argyre Planitia, initially proposed by Parker to the Mars Surveyor Landing Site program, is also proposed for potential consideration for post-2001 missions to Mars, as it is well outside the current latitude limits for the Athena Rover. All three sites are designed to be situated as close to a diversity of geologic units within a few kilometers of the landing site so that diversity can be placed in a geologic context. This objective is very different from the Mars Pathfinder requirement to land at a site with a maximum chance for containing a diversity of rocks within a few tens of meters of the lander. That requirement was driven by the Sojourner mobility limit of a few tens of meters. It can be argued that the Athena project, with its much larger mobility capability, might actually want to avoid such a site, because placing collected samples in geologic context would be difficult. While it has been argued, both before and after the Mars Pathfinder landing, that the provenance for local blocks may be determined by orbiter spectra, primarily from the MGS TES instrument, our ability to do so has yet to be demonstrated. Indeed, several months after conclusion of the Pathfinder mission, we have yet to reach a consensus on the composition of local materials. Our primary data set for selecting a landing site within the latitude and elevation constraints of the 2001 mission is the Viking Orbiter image archive. The site must be selected to place the landing ellipse so as to avoid obvious hazards, such as steep slopes, large or numerous craters, or abundant large knobs. For this purpose, we chose a resolution limit of better than 50 m/pixel. This necessarily excludes from the present study images from current and future orbiter spacecraft, until such data does become readily available. Within each proposed region, it may be possible to identify additional sites once these data become available. Second, the fine-component thermal inertia data, should be greater than about 5 or 6 cgs Units (10(exp -3) cal/sq cm s(exp -0.5)/K). Low thermal inertias imply dusty environments, which could pose a mobility hazard. Similarly, the albedo of the site should not be particularly high, which would also suggest dusty surfaces. Low albedos are preferred, as they often coincide with low Viking red:violet ratios and indicate less dusty surfaces. Next, the Modeled Block Abundance should also not be too high or too low. Based on the Viking Lander and Mars Pathfinder experiences, percentages of blocks should be on the order of 5-25%. Too many blocks could pose a hazard to the landing and mobility. Too few blocks could also indicate a dusty surface. Primary Landing Site: Northern Meridiani Sinus (Proposed by T. J. Parker and K., S. Edgett) Vital Statistics: (1) Latitude, Longitude: 0-3 N, 350-2 W. *Elevation (Viking): about0.5-1.5 Ian. (2) Viking Orbiter Image coverage: Excellent coverage by 15 - 25 m/pixel images (orbits 709A and 410B). Possible stereo coverage in region where two orbits overlap (probably small parallax angle, as these orbits are not listed in NASA Contractor Report 3501) (3) Albedo: about .18 -.26 (4) Block Abundance: 5-26% (5)Fine-Component Thermal Inertia: 5-9 cgs units This region consists of bright deposits similar to those described by Edgett et al, that also lie within a prominent dark albedo region. These deposits are flat-lying, to such a degree that they ramp against topography rather than draping over it. This led Edgett and Parker to suggest that they may be subaqueous sediments, possibly lacustrine or marine evaporites, laid down sometime from the late Noachian to middle Hesperian (age determination pending crater counts). A contact between this material and elevated, dissected highlands to the south was identified , and is described by Edgett et al. Our desire in proposing this landing site is to sample the edge of this deposit where it has been exposed through etching, presumably eolian deflation (the deposit, though in the highlands, is itself only lightly to moderately cratered). This should enable access to in situ stratigraphy. The actual landing site will be selected where slopes are not expected to be steep, such that the rover itself should be able to traverse them and sample layered materials on the way, either up or down the slope. Perhaps due to uncertainties at this time as to the friability or meter-scale roughness of the deposit, it might make sense to place the landing ellipse on the exhumed highland surface adjacent to the deflated margin of the deposit and plan on driving to the deposit rather than landing on it and driving downslope. This should also enable imaging the margin for evidence of layering should it prove too difficult to climb. A target ellipse on the highland surface should also allow Athena access to ancient Noachian highland materials, particularly if placed near crater ejecta or an inlier of knobby material. Secondary Landing Site: Southern Elysium Planitia (Proposed by T. J. Parker) Vital Statistics: (1) Latitude, Longitude: 1.5-3.5 S, 195-198 W. (2) Elevation (Viking): -1.0 km. (3) Viking Orbiter Image coverage: Excellent coverage by 15 - 25 m/pixel images (orbit 725). Possible stereo coverage between images from beginning and end of orbit that overlap (probably small parallax angle) (4) Albedo: about .27-.28 (5) Block Abundance: 4-7% (6) Fine-Component Thermal Inertia: about 3 cgs units This region consists of eroded knobby material, probably of Noachian age, though much of the crater population has been destroyed, that is onlapped at a sharp contact by an extensive plains unit in southern Elysium Planitia that is Amazonian in age. The plains materials have been attributed to unusually low-viscosity flood lavas from fissures south of the Elysium volcanic rise, or to lacustrine materials associated with a large, Amazonian lake at the source of Marte Vallis. Parker and Schenk presented evidence in support of the latter interpretation, though they attributed the putative shore morphology to an embayment of a northern plains ocean into the southern Elysium region. Detailed examination of the margin of the deposit, showing erosion, not simply burial, of small crater rims and fluidized ejecta blankets, also points to lacustrine or marine sedimentation rather than volcanic plains burial. The plains surface exhibits a "crusty" appearance that many researchers have attributed to pressure ridges in lava flows. In a lacustrine context, they also resemble pressure ridges in desiccated evaporite deposits and salt-rimmed pools (now dry) similar in scale and morphology to spectacular, hundred meter-scale pool rims in alkaline Lake Natron, East African Rift. The eroded highland margin surface adjacent to these plains appears to be fairly smooth, even at 15 m/pixel. Isolated knob inliers are scattered from a few kilometers to several tens of "kilometers apart. Heights of the knobs have not been measured yet but, based on experience with similar features in the Pathfinder landing ellipse, are probably typically on the order of several tens of meters high and smaller, though some of the largest knobs in the region are probably up to a few hundred meters high. Two craters larger than a kilometer in diameter, with fluidized deposits, lie nearby the proposed landing site. Very high-resolution images from MOC should help to determine whether a landing site navigable by the Athena rover could be placed in this region. The space between knobs and craters is large enough to enable placement of a target landing ellipse between them but still provide access to one or more of them and to the margin of the Elysium plains material. Post-2001 Mars Surveyor Landing Site: Argyre Planitia (Proposed by T. J. Parker) Vital Statistics: (1) Latitude, Longitude: 55-56 S, 41-43 W. (2) Elevation (Viking): 1.0 km. (3) Viking Orbiter Image coverage: Excellent coverage by 40 m/pixel images (orbits 567B, 568B, and 569B). Excellent stereo coverage with large parallax angles over the entire landing site region, and much of central and southern Argyre. (4) Albedo: about .23-.24 (5) Block Abundance: No data (6) Fine-Component Thermal Inertia: No data The floors of both the Argyre and Hellas basins contain etched layered materials that are probably thick accumulations of channel or lacustrine sediments. The deposits in Hellas are much more eroded than those in Argyre, and Hellas lacks a channel outlet. Argyre is unique in that Uzboi Vallis flowed out of the basin, requiring overflow of a standing body of water within Argyre. This makes it the largest impact basin on Mars with channels both draining into it and flowing out from it. Hellas' channels may be catastrophic flood channels, whereas Argyre was fed by modest-scale valley networks, though the outlet at Uzboi Vallis was a catastrophic flood Highland craters and basins of this kind should be high-priority landing targets for missions intended to focus on the search for either prebiotic organic materials or even simple fossil microorganisms. Basins with internally-draining valley networks should be preferred over flood channels, as they could have provided the long-term influx of water favorable to the origin of life. (Catastrophic floods are not conducive to fossil preservation, due to their very short durations and high transportation energies). They also afford an opportunity to study the evolution of the planet's climate and volatiles during the period of time between the late Noachian and early Hesperian, when a drastic change from a proposed early warm, wet climate to one more closely resembling the modern environment is thought to have occurred. Large basin

Description: The Mars Surveyor missions that will be launched in April of 2001 will include a highly capable rover that is a successor to the Mars Pathfinder mission's Sojourner rover. The design goals for this rover are a total traverse distance of at least 10 km and a total lifetime of at least one Earth year. The rover's job will be to explore a site in Mars' ancient terrain, searching for materials likely to preserve a record of ancient martian water, climate, and possibly biology. The rover will collect rock and soil samples, and will store them for return to Earth by a subsequent Mars Surveyor mission in 2005. The Athena Mars rover science payload is the suite of scientific instruments and sample collection tools that will be used to perform this job. The specific science objectives that NASA has identified for the '01 rover payload are to: (1) Provide color stereo imaging of martian surface environments, and remotely-sensed point discrimination of mineralogical composition. (2) Determine the elemental and mineralogical composition of martian surface materials. (3) Determine the fine-scale textural properties of these materials. (4) Collect and store samples. The Athena payload has been designed to meet these objectives. The focus of the design is on field operations: making sure the rover can locate, characterize, and collect scientifically important samples in a dusty, dirty, real-world environment. The topography, morphology, and mineralogy of the scene around the rover will be revealed by Pancam/Mini-TES, an integrated imager and IR spectrometer. Pancam views the surface around the rover in stereo and color. It uses two high-resolution cameras that are identical in most respects to the rover's navigation cameras. The detectors are low-power, low-mass active pixel sensors with on-chip 12-bit analog-to-digital conversion. Filters provide 8-12 color spectral bandpasses over the spectral region from 0.4 to 1.1 micron Narrow-angle optics provide an angular resolution of 0.28 mrad/pixel, nearly a factor of four higher than that of the Mars Pathfinder and Mars Surveyor '98 cameras. Image compression will be performed using a wavelet compression algorithm. The Mini-Thermal Emission Spectrometer (Mini-TES) is a point spectrometer operating in -the thermal IR. It produces high spectral resolution (5 /cm) image cubes with a wavelength range of 5-40 gm, a nominal signal/noise ratio of 500:1, and a maximum angular resolution of 7 mrad (7 cm at a distance of 10 in). The wavelength region over which it operates samples the diagnostic fundamental absorption features of rockforming minerals, and also provides some capability to see through dust coatings that could tend to obscure spectral features. The mineralogical information that Mini-TES provides will be used to select from a distance the rocks and soils that will be investigated in more detail and ultimately sampled. Mini-TES is derived from the MO/MGS TES instrument, but is significantly smaller and simpler. The instrument uses an 8-cm Cassegrain telescope, a Michelson interferometer, and uncooled pyroelectric detectors. Along with its mineralogical capabilities, Mini-TES can provide information on the thermophysical properties of rocks and soils. Viewing upward, it can also provide temperature profiles through the martian atmospheric boundary layer. Elemental and Mineralogical Composition: Once promising samples have been identified from a distance using Pancam/Mini-TES, they will be studied in detail using up to three compositional sensors that can be placed directly against them by an Instrument Arm. The two compositional sensors, presently on the payload are an Alpha-Proton-X-Ray Spectrometer (APXS), and a Mossbauer Spectrometer. The APXS is derived closely from the instrument that flew on Mars Pathfinder. Radioactive alpha sources and three detection modes (alpha, proton, and x-ray) provide elemental abundances of rocks and soils to complement and constrain mineralogical data. The Athena APXS will have a revised mechanical design that will cut down significantly on backscattering of alpha particles from martian atmospheric carbon. It will also include a target of known elemental composition that will be used for calibration purposes. The Athena Mossbauer Spectrometer is a diagnostic instrument for the mineralogy and oxidation state of Fe-bearing phases, which are particularly important on Mars. The instrument measures the resonant absorption of gamma rays produced by a Co-57 source to determine splitting of nuclear energy levels in Fe atoms that is related to the electronic environment surrounding them. It has been under development for space flight for many years at the Technical University of Darmstadt. The Mossbauer Spectrometer (and the other arm instruments) will be able to view a small permanent magnet array that will attract magnetic particles in the martian soil. The payload may also include a Raman Spectrometer. If included, the Raman Spectrometer will provide precise identification of major and minor mineral phases. It requires no sample preparation, and is also sensitive to organics. Fine-Scale Texture: The Instrument Arm a also carries a Microscopic Imager that will obtain high-resolution monochromatic images of the same materials for which compositional data will be obtained. Its spatial resolution is 20 micron/pixel over a 1 cm depth of field, and 40 micron/pixel over a 1-cm depth of field. Like Pancam, it uses the same active pixel sensor detectors and electronics as the rover's navigation cameras. The Instrument Arm is a three degree-of-freedom arm that uses designs and components from the Mars Pathfinder and Mars Surveyor '98 projects. Its primary function is instrument positioning. Along with the instruments noted above, it also carries a brush that can be used to remove dust and other loose coatings from rocks. Sample Collection and Storage: Martian rock and soil samples will be collected using a low-power rotary coring drill called the Mini-Corer. An important characteristic of this device is that it can obtain intact samples of rock from up to 5 cm within strong boulders and bedrock, Nominal core dimensions are 8xl7 mm. The Mini-Corer drills a core to the commanded depth in a rock, shears it off, retains it, and extracts it. It can also acquire samples of loose soil, using soil sample cups that are pressed downward into loose material. The Mini-Corer can drill at angles from vertical to 45' off vertical. It has six interchangeable bits for long life. Mechanical damage to the sample during drilling is minimal, and heating is negligible. After acquisition, the sample may be viewed by the arm instruments, and/or placed in one of 104 compartments in the Sample Container. A subset of the acquired samples may be replaced with other samples obtained later if desired. The Sample Container has no moving parts, and is mounted external to the rover for easy removal by the Mars Surveyor 2005 flight system. Operation of the rover will make extensive use of automated onboard navigation and hazard avoidance capabilities. Otherwise, use of onboard autonomy is minimal. Data downlink capability is about 40 Mbit/sol, and the use of the Mars Surveyor '01 orbiter for data relay imposes a limit of at most two command cycles per sol. Because of the significant amount of time available between command cycles, all payload elements will be operated sequentially, rather than in parallel.; this approach also significantly simplifies operations and minimizes peak power usage. The landing site for the '01 rover has not been selected yet. Site selection will make as full use as possible of Mars Global Surveyor data, and will involve substantial input from the broad Mars science community. Summary: The following table describes the mass, power, providers, and key scientific objectives of all the major elements of the Athena payload. Additional Athena payload information may be found at: http://astrosun.tn.cornell.edu/athena/index.html. Additional information contained in the original.

Description: During the Hubble Space Telescope (HST) Second Servicing Mission (SM2), degradation of unsupported Teflon(R) FEP (fluorinated ethylene propylene), used as the outer layer of the multi-layer insulation (MLI) blankets, was evident as large cracks on the telescope light shield. A sample of the degraded outer layer was retrieved during the mission and returned to Earth for ground testing and evaluation. The results of the Teflon(R) FEP sample evaluation and additional testing of pristine Teflon(R) FEP led the investigative team to theorize that the HST damage was caused by thermal cycling with deep-layer damage from electron and proton radiation which allowed the propagation of cracks along stress concentrations, and that the damage increased with the combined total dose of electrons, protons, UV and x-rays along with thermal cycling. This paper discusses the testing and evaluation of the Teflon(R) FEP.

Description: The 1998 lander payload consists of a descent imager, the Mars Volatiles and Climate Surveyor (MVACS) instruments (lander stereo camera, arm-mounted close-up imager, meteorology package, thermal and evolved gas analyzer), and a LIDAR instrument. The mission focuses on assessment of near-surface water ice in the south polar region, and the volatile and climate history of Mars. In order to achieve these objectives, the landing site must allow access to polar layered deposits by the robotic arm, which may be able to dig as much as 0.5 m below the surface. Hence, the presence of recent aeolian debris at the landing site may adversely affect the ability of the MVACS instruments to gather the samples and acquire data needed to properly address the science objectives. The studies described here include mapping surface units in the landing region (73S - 77S, 140W - 230W) to infer the distribution of aeolian debris and to identify potential landing sites where mantling is minimal. Because the '98 lander will not be able to survive very low temperature conditions, this study also includes mapping of south polar seasonal frost retreat based on Viking Orbiter images. The results of this work, in conjunction with complementary studies by other investigators, will facilitate the selection of the Mars Surveyor 1998 landing site (and backup) by the summer of 1998.

Description: The debouche of Ma'adim Vallis in the Elysium Basin generated a transitional transported sediment structure, which planimetric shape is controlled by the enclosing topography of a deep reentrant gulf of the Basin into the highland. We defined it as an estuarine delta. The location and the importance of this estuarine delta is supported by the theoretical model of graded profile constructed for Ma'adim Vallis, and by two approaches: (i) the reconstruction of Ma'adim Vallis downstream course from Gusev to Elysium Basin, and (ii) the survey of the sediment deposit in the alleged estuary. The longitudinal graded profile of Ma'adim Vallis finds its base-level in the Elysium Basin, at a about 1000 m elevation, which is in agreement with the observed Basin shoreline. This model is supported by observational evidence of flow between the northern rim of Gusev crater, and the Elysium Basin shoreline. This downstream course of Ma'adim Vallis can be divided into three hydrogeologic regions. into three hydrogeologic regions. (a) The first region is a flooded plain (Zephiria Mensae), consisting in chaotic terrain formed by highland rocks, and disintegrated lava of the western flank of Apollinaris. Morphologic indicators of the flood process are: (1) the sediment deposit over the Gusev crater northern rim that reflects the overspilling of the crater-lake water through a 40-km wide gap provided by an ancient impact crater, (2) the tear-drop shaped feature on the northeastern flank of Apollinaris Patera, and (3) the chaotic terrain that suggest the emergence of ground water generated by the seepage of the crater lake through high-permeable broken rampart material. This underground water circulation sustained by the hydrostatic pressure of the crater-lake has likely generated a hydrothermal system in the volcanic environment of Apollinaris Patera. The stratigraphy of the flooded area is identified as Hesperian age, with occurrences of Noachian hilly individual features, and as Amazonian flooded plain and chaotic material, (b) The second region is located on the western flank of Apollinaris Patera. It is surrounded by relics of deep valleys that suggest a former downstream course of Ma'adim Vallis. The geologic setting of this region (Lucus Planum) is interpreted to be an Amazonian formation composed by the middle and lower members of the Medusae Formation., c) The third region corresponds to the convergence of the west and east branches of Ma'adirn Vallis into a deep re-entrant wide gulf that penetrates about 100 km into the highland. This topographic depression is delineated by the 1000 in elevation contour. This gulf has formed an estuarine configuration centered at 3S/190W within the Elysium Basin. This configuration has favored the formation of a estuarine sedimentary delta, because of topographically controlled lateral migration. This estuarine structure is strongly dominated by the incoming supply of Ma'adim Vallis fluvial sediment extracted from Zephiria Mensae and Lucus Planum. The obtuse-angle geometry of the estuary increases the sedimentation rate, which is higher than in the course of the channel. The sediment deposition process is governed by the estuarine water circulation. The inflowing loaded fluvial water enters the estuary as a bottom current, and mixes with the relatively less-loaded water of the receiving basin. When they mixed. the inflowing fluvial material, and the landward basin circulating water generate an accumulation of highly-diversified estuarine deposit stratification. This accumulation of material is mostly centered in the transitional zone of the delta. The sediment trapping efficiency of the estuary is function of the energy balance between the inflowing fluvial water, and the ingoing basin current. The submergence of the delta by the rising of the water-level increases the estuary water-depth, and consequently the sediment entrapment is favored. The locus of sediment accumulation moves landward in the zone of inflowing fluvial water. This results in the rising of the channel base-level, thus in the increase of the length of the longitudinal graded-profile. The sediment deposit facies of the zone A shows a generally smooth surface. The longitudinal deposit is bordered by alluvial terraces that reflect the variations of the channel level. The waning of the Elysium Basin caused the erosion of the Basin estuarine zone by small channels, this episode being characterized by dissected tear-drop shaped mesa-like morphologies in the delta. Our estuarine delta model predicts a lithostratigraphic depositional sequence associated with the water submergence and the transgression of Elysium Basin. The thickness of the estuarine sediment corresponds to the Elysium Basin levels changes relatively to the bed floor of the estuary, The depositional sequence of Ma'adim Vallis are described: (1) a pro-current filled region (A), where fluvial are longitudinally accumulated by the inflowing water, (2) inverse current from Elysium Basin (B), where fluvial and lacustrine sediments are accumulated, and (3) zone of current equilibrium (C), where the sediments are distributed as a shoreline at the boundary of the estuarine delta. The estuary sedimentology dynamics collects and keeps the record of the geologic unit material crossed by Ma'adim Vallis, and those of the lakebed deposit of Elysium Basin. The predicted mixed stratigraphic sequence from fluvial and lacustrine sediment makes this site an exceptional environment to concentrate potential multi-origin biologic records. We envision four possible strategies to explore this sedimentologic record: (1) longitudinal surface and subsurface traverses in region A to investigate outcrop levees, (2) exploration of the mesa walls in region B, (3) deep drilling hole lodging of the sequential deposits in the zones A and B, and (4) surface and subsurface exploration of the shoreline delta. The expected results for each of these strategies are: (1) in the deepest layers of region A are predicted frequent and abundant coarse material, sandy lenses lamination grading downward from sand to cobbles. Volcanic debris from the Noachian crustal Plateau unit material, hydrothermal altered rocks, carbonates, Hesperian and possibly Amazonian volcanic material, from Apollinaris Patera, altered rocks and carbonates from Zephiria Mensae are expected. As a favorable environment for inception of life, possible biological records are expected in transported rock, (2) At the surface, and subsurface (〈=100 m), large deposits sandy to silted material from Elysium paleolake basin mixed with fine-grained sediments from Ma'adim Vallis are expected mostly in the upstream part of region B, (3) on the shoreline of the estuarine delta, abundant fine material from Elysium paleolake basin (evaporites, carbonates), mostly Amazonian in age are expected. The Ma'adini estuary is a favorable landing site for all the above mentioned science aspects, and .for its location. The site lies near the equator, which is favorable for the rover solar power supply, and at 1000m elevation, which is a favorable configuration for the descent system braking. Another advantage is the extent of the area of high scientific interest (33,000 sq km), which provides a good ellipse, and potential long study traverses.

Description: Ancient Martian lakes are sites where the climatological, chemical, and possibly biological history of the planet has been recorded. Their potential to keep this global information in their sedimentary deposits, potential only shared with the polar layered-deposits, designates them as the most promising targets for the ongoing exploration of Mars in terms of science return and global knowledge about Mars evolution. Many of the science priority objectives of the Surveyor Program can be met by exploring ancient Martian lake beds. Among martian paleolakes, lakes in impact craters represent probably the most favorable sites to explore. Though highly destructive events when they occur, impacts may have provided in time a significant energy source for life, by generating heat, and at the contact of water and/or ice, deep hydrothermal systems, which are considered as favorable environments for life. In addition, impact crater lakes are changing environments, from thermally driven systems at the very first stage of their formation, to cold ice-protected potential oases in the more recent Martian geological times. Thus, they are plausible sites to study the progression of diverse microbiologic communities.

Description: Materials that pyrolyze at elevated temperature have been commonly used as thermal protection materials in hypersonic flight, and advanced pyrolyzing materials for this purpose continue to be developed. Because of the large temperature gradients that can arise in thermal protection materials, significant thermal stresses can develop. Advanced applications of pyrolytic materials are calling for more complex heatshield configurations, making accurate thermal stress analysis more important, and more challenging. For non-pyrolyzing materials, many finite element codes are available and capable of performing coupled thermal-mechanical analyses. These codes do not, however, have a built-in capability to perform analyses that include pyrolysis effects. When a pyrolyzing material is heated, one or more components of the original virgin material pyrolyze and create a gas. This gas flows away from the pyrolysis zone to the surface, resulting in a reduction in surface heating. A porous residue, referred to as char, remains in place of the virgin material. While the processes involved can be complex, it has been found that a simple physical model in which virgin material reacts to form char and pyrolysis gas, will yield satisfactory analytical results. Specifically, the effects that must be modeled include: (1) Variation of thermal properties (density, specific heat, thermal conductivity) as the material composition changes; (2) Energy released or absorbed by the pyrolysis reactions; (3) Energy convected by the flow of pyrolysis gas from the interior to the surface; (4) The reduction in surface heating due to surface blowing; and (5) Chemical and mass diffusion effects at the surface between the pyrolysis gas and edge gas Computational tools for the one-dimensional thermal analysis these materials exist and have proven to be reliable design tools. The objective of the present work is to extend the analysis capabilities of pyrolyzing materials to axisymmetric configurations, and to couple thermal and mechanical analyses so that thermal stresses may be efficiently and accurately calculated.

Description: Accurate knowledge of the thermophysical properties of TPS (thermal protection system) materials is necessary for pre-flight design and post-flight data analysis. Thermal properties, such as thermal conductivity and the volumetric specific heat, can be estimated from transient temperature measurements using non-linear parameter estimation methods. Property values are derived by minimizing a functional of the differences between measured and calculated temperatures. High temperature thermal response testing of TPS materials is usually done in arc-jet or radiant heating facilities which provide a quasi one-dimensional heating environment. Last year, under the NASA-ASEE-Stanford Fellowship Program, my work focused on developing a radiant heating apparatus. This year, I have worked on increasing the fidelity of the experimental measurements, optimizing the experimental procedures and interpreting the data.

Description: NASA is seeking to develop thermal insulation material systems suitable for withstanding both extremely high temperatures encountered during atmospheric re-entry heating and aero- braking maneuvers, as well as extremely low temperatures existing in liquid fuel storage tanks. Currently, materials used for the high temperature insulation or Thermal Protection System (TPS) are different from the low temperature, or cryogenic insulation. Dual purpose materials are necessary to the development of reusable launch vehicles (RLV). The present Space Shuttle (or Space Transportation System, STS) employs TPS materials on the orbiter and cryo-insulation materials on the large fuel tank slung under the orbiter. The expensive fuel tank is jettisoned just before orbit is achieved and it burns up while re-entering over the Indian Ocean. A truly completely reusable launch vehicle must store aR cryogenic fuel internally. The fuel tanks will be located close to the outer surface. In fact the outer skin of the craft will probably also serve as the fuel tank enclosure, as in jet airliners. During a normal launch the combined TPS/cryo-insulation system will serve only as a low temperature insulator, since aerodynamic heating is relatively minimal during ascent to orbit. During re-entry, the combined TPS/cryo-insulation system will serve only as a high temperature insulator, since all the cryogenic fuel will have been expended in orbit. However, in the event of an.aborted launch or a forced/emergency early re-entry, the tanks will still contain fuel, and the TPS/cryo-insulation will have to serve as both low and high temperature insulation. Also, on long duration missions, such as to Mars, very effective cryo-insulation materials are needed to reduce bod off of liquid propellants, thereby reducing necessary tankage volume, weight, and cost. The conventional approach to obtaining both low and high temperature insulation, such as is employed for the X-33 and X-34 spacecraft, is to use separate TPS and cryo-insulation materials, which are connected by means of adhesives or stand-offs (spacers). Three concepts are being considered: (1) the TPS is bonded directly to the cryo-insulation which, in turn, is bonded to the exterior of the tank, (2) stand-offs are used to make a gap between the TPS and the cryo-insulation, which is bonded externally to the tank, (3) TPS is applied directly or with stand-offs to the exterior so the tank, and cryo-insulation is applied directly to the interior of the tank. Many potential problems are inherent in these approaches. For example, mismatch between coefficients of thermal expansion of the TPS and cryo-insulation, as well as aerodynamic loads, could lead to failure of the bond. Internal cryo-insulation must be prevent from entering the sump of the fuel turbo-pump. The mechanical integrity of the stand-off structure (if used) must withstand multiple missions. During ground hold (i.e., prior to launch) moisture condensation must be minimized in the gap between the cryo-insulation and the TPS. The longer term solution requires the development of a single material to act as cryo- insulation during ground hold and as TPS during re-entry. Such a material minimizes complexity and weight while improving reliability and reducing cost.

Description: This paper details a comparison analysis of the zinc-oxide pigmented white thermal control paints Z-93 and Z-93P. Both paints were simultaneously exposed to combined space environmental effects and analyzed using an in-vacuo reflectance technique. The dose applied to the paints was approximately equivalent to 5 yr in a geosynchronous orbit. This comparison analysis showed that Z-93P is an acceptable substitute for Z-93. Irradiated samples of Z-93 and Z-93P were subjected to additional exposures of ultraviolet (UV) radiation and analyzed using the in-vacuo reflectance technique to investigate UV activated reflectance recovery. Both samples showed minimal UV activated reflectance recovery after an additional 190 equivalent Sun hour (ESH) exposure. Reflectance response utilizing nitrogen as a repressurizing gas instead of air was also investigated. This investigation found the rates of reflectance recovery when repressurized with nitrogen are slower than when repressurized with air.

Description: During the Second Servicing Mission (SM2) of the Hubble Space Telescope (HST) severe degradation was observed on the outer layer of the thermal control blankets. Astronaut observations and photographs revealed large cracks in the metallized Teflon(R) FEP (fluorinated ethylene propylene), the outer layer of the multi-layer insulation (MLI), in many locations around the telescope. In an effort to understand what elements of the space environment might cause such damage, pristine Teflon(R) FEP was tested for durability to radiation and thermal cycling. Specimens were subjected to electron and proton fluences comparable to those experienced by HST and were subsequently thermal cycled in a custom-built rapid thermal cycle chamber. Tensile tests of the specimens showed that radiation followed by thermal cycling significantly reduced the ultimate strength and elongation of Teflon(R) FEP.

Description: As a reinforcement for structural composites, single crystal alumina fibers offer low density, high modulus, and high creep resistance. In this study, the laser heated float zone approach was employed to grow c-axis Al2O3 continuous fibers of high purity and high strength. A new melt modulation technique, laser scanning, avoids the formation of surface induced ripples and allows the growth of 50 micro-m diameter sapphire fibers with strengths (approx. 7 GPa) significantly greater than either commercially available fibers grown by the edge-defined film growth process (approx. 2-3 GPa) or laboratory fibers grown by stationary laser heating (approx. 5 GPa). The present work suggests that surface striations are the predominant defects controlling the tensile strength of laser-scanned fibers at room temperature. Several possible mechanisms for inducing surface striations are systematically discussed for several oxide fiber compositions.

Description: Ceramic thermal barrier coatings have attracted increased attention for diesel engine applications. The advantages of using the ceramic coatings include a potential increase in efficiency and power density and a decrease in maintenance cost. Zirconia-based ceramics are the most important coating materials for such applications because of their low thermal conductivity, relatively high thermal expansivity and excellent mechanical properties. However, durability of thick thermal barrier coatings (TBCS) under severe temperature cycling encountered in engine conditions, remains a major question. The thermal transients associated with the start/stop and no-load/full-load engine cycle, and with the in-cylinder combustion process, generate thermal low cycle fatigue (LCF) and thermal high cycle fatigue (HCF) in the coating system. Therefore, the failure mechanisms of thick TBCs are expected to be quite different from those of thin TBCs under these temperature transients. The coating failure is related not only to thermal expansion mismatch and oxidation of the bond coats and substrates, but also to the steep thermal stress gradients induced in the coating systems. Although it has been reported that stresses generated by thermal transients can initiate surface and interface cracks in a coating system, the mechanisms of the crack propagation and of coating failure under the complex LCF and HCF conditions are still not understood. In this paper, the thermal fatigue behavior of an yttria partially stabilized zirconia coating system under simulated LCF and HCF engine conditions is investigated. The effects of LCF and HCF on surface crack initiation and propagation are also discussed.

Description: The use of thermal barrier coatings (TBC's) in gas turbines has increased dramatically in recent years, due mainly to the need for component protection from ever increasing service temperatures. Oxidation of the bond coat has been identified as an important contributing factor to spallation of the ceramic top coat during service. Additional variables found to influence TBC thermal cycle life include bond coat coefficient of thermal expansion, creep behavior of both the ceramic and bond coat layers, and modulus of elasticity. The purpose of this work was to characterize the effects of oxidation on the stress states within the TBC system, as well as to examine the interaction of oxidation with other factors affecting TBC life.

Description: Gale is a 140-km diameter impact crater located at the plateau/plain boundary in the Aeolis Northeast subquadrangle of Mars (5S/223W). The crater is bordered in the northward direction by the Elysium Basin, and in eastward direction by Hesperian channels and the Aeolis Mensae 2. The crater displays a rim with two distinct erosion stages: (a) though eroded, the south rim of Gale has an apparent crest line visible from the north to the southwest (b) the west and northwest rims are characterized by a strong erosion that, in some places, partially destroyed the rampart, leaving remnant pits embayed in smooth-like deposits. The same type of deposits is observed north, outside Gale, it also borders the Aeolis Mensae, covers the bottom of the plateau scarp, and the crater floor. The central part of Gale shows a 6400 km2 subround and asymmetrical deposit: (a) the south part is composed of smooth material, (b) the north part shows spectacular terraces, streamlines, and channels. The transition between the two parts of the deposit is characterized by a scarp ranging from 200 to 2000 in high. The highest point of the scarp is at the center of the crater, and probably corresponds to a central peak. Gale crater does not show a major channel directly inflowing. However, several large fluvi systems are bordering the crater, and could be at the origin of the flooding of the crater, or have contributed to. One fluvial system is entering the crater by the southwest rim but cannot be accounted alone for the volume of sediment deposited in the crater. This channel erodes the crater floor deposit, and ends in a irregular-shaped and dark albedo feature. Gale crater shows the morphology of a crater filled during sedimentation episodes, and then eroded Part of the lower sediment deposition contained in Gale might be ancient and not only aqueous in origin. According to the regional geologic history, the sedimentary deposit could be a mixture of aeolian and pyroclastic material, and aqueous sedimentary material that can originate both from drainage of the regional subsurface aquifer, and/or from surface flood. The central deposit shows three main levels: (a) the current crater floor (north of Gale), (b) an ancient level about 200 rn higher (south of Gale), and (c) the massive terraced deposits. A crater statistics on the 15,400 kM2 area of the crater floor and deposit [3,41 gave: 259+/-112.4 craters, most of them partly embayed in the sedimentary deposit, and all inferior to 5-km diameter. For superimposed crater population only, the result is 194+/-112. The deduced relative ages ranges from Early to Middle Amazonian. The population of craters are comparable for the three levels, implying that the last sedimentation/erosion episode on Gale was recent and affected the whole crater. The streamlined morphology of the border of the deposit, the layering, the channels, and the terraces are compatible with a significant fluvio-lacustrine history of the site. Multiple levels may suggest different episodes, but the common statistical age of the three levels shows that the last episode involved the whole crater. The origin of the lake water in Gale may have varied in time. Three major contributions have been proposed: (a) the drainage of the regional underground aquifer by Gale crater over an area of 110-km radius around the crater which would have provided approximately 1,600 cubic km of water, (b), surface drainage entering Gale by the south and north rims. In the south, a 250-km long system originates in the cratered uplands in a Noachian crater material plain (Nc), and crosses Hesperian and Amazonian crater material plains (AHc) northward [1]. Several fluvial systems originate in the Aeolis Mensae, east of Gale. They may had two functions in time: to recharge, the underground aquifer in the region of Gale, and to supply surface water in the crater by overspilling the northern rim, and (c) surface floods that originated from the rising of the water level in the Elysium Basin. According to the Amazonian age of Gale's floor, and the erosion direction in the crater, a flood from Elysium Basin is the most likely event to explain the material observed in Gale, and the formation of the last lake. This last flood may have been important enough to flood the central deposit up to about 1400 m above the crater floor, leaving two islands (non stream lined features) at the center of the deposit. Terrace spacing suggests a regular drop of the lake level in time. Fractures in terraces perpendicular to the shoreline can be interpreted either as: (a) the result of the drainage systems during the waning of the lake, or (b) traces of the pressure of an ice-covered sheet associated with subglacial drainage. The presence of a lake of such volume during the Amazonian period is one more evidence that water was still active on Mars relatively recently. Gale crater offers the rare opportunity to unveil a key-period of the martian history. The Amazonian might proved not as cold and dry as previously thought. The presence of large lakes and basins (Elysium Basin is large as the Mediterranean Sea), reinforces the model of an extensive water activity during the Amazonian that has still to be understood in the context of an assumed cooling and drying planet. The sediments and rocks that were left of this period in Gale keep the record of the climatic conditions of the Amazonian and the clues that are missing to understand the climatic evolution of Mars. In addition, Gale crater presents the advantage to be located at the plateau/plain boundary, which has never been studied and contains information about the two main martian geological units. As a conclusion, we propose a table that summarizes the worthiness of a mission in Gale crater, and the expected science return relative to the objectives to be met by the Surveyor Program. Additional information contained in the original.

Description: Landing sites near Apollinaris Patera are proposed for the Mars Surveyor 2001 lander/rover mission. Regions near the base of Apollinaris Patera provide a unique opportunity within the proposed -15 deg to 30deg latitude belt to sample outcrop lithologies ranging from highland Noachian basement rocks, to Hesperian aged lava flows, channel and flood plain materials, to Amazonian volcanic, ash flow, and channel deposits. Pristine impact craters exhibiting lobate ejecta blankets are found both on the volcano itself and on the surrounding terrain implying a ground water rich environment well into the Amazonian. Therefore its formation likely induced long-lived volcanic-hydrothermal systems, a high priority target for the mission.

Description: Mangala Valles is an outflow channel in the Memnonia region of Mars. Although its origin is still under debate, most researchers believe they represent some form of catastrophic flood system which occurred early in the evolutionary history of Mars. The scientific objective of the Mars Surveyor Program 2001 (MSP 01) landed mission is to examine the ancient climatic and geologic history of Mars; to characterized surface materials with respect to elemental and mineral composition of rock and soils; to identify the role water may have played with respect to evolutionary history of the surface; to look for samples which may contain possible evidence of ancient life; and to collect and store unaltered samples which may be eventually returned to Earth during a later mission (MSP 05 - 2005). As with the Mars Pathfinder lander, the landing site will depend on several engineering constraints. Preliminary engineering constraints for MSP 01 landing site is that the landing site lies with 30 N and -15 S of the equator (due to solar power limitations) and below 2 km elevation. Both the scientific objectives and the engineering constraints can be accommodated with a Mangala Valles landing site.

Description: Human exploration of Mars will consist of a series of long-term missions, with early missions focusing upon establishing the Mars base, and undertaking basic field reconnaissance. A capable laboratory on Mars is an essential element in the exploration strategy. Analytical equipment both in the field and in the laboratory serves to extend the senses of the crew and help them sharpen their sampling skills as they learn to recognize rocks in the field and understand their geologic context and significance. On-site sample analyses allow results to be incorporated into evolving surface exploration plans and strategies, which will be developing in real-time as we learn more about Mars. Early Mars missions will focus on reconnaissance EVAs to collect rock and soil samples, maximizing the amount of Mars material returned to Earth. Later missions will be increasingly devoted to both extensive field campaigns and laboratory analyses. The capabilities and equipment described below will be built up at the Mars base incrementally over many missions, with science payloads and investigative infrastructure being partitioned among launch opportunities. This discussion considers what we require to measure, observe, and explore on a new planetary territory. Alternatively, what do we need to know and how do we equip ourselves to provide ample capabilities to acquire these data? Suggestions follow describing specific instruments that we could use. Appendix 5 lists a strawman science instrument payload, and a feasibility study of equipment transportation into the field on pressurized or unpressurized rovers.

Description: The two major constraints for selecting the Mars Surveyor Program (MSP) 2001 landing site at the time of this meeting are latitude (30'N to 15S) and elevation (〈 2.5 km). The latitude belt will be narrowed down to a 15' sector after this workshop. This mission will demonstrate the capability to perform a precision landing, with the goal of achieving an accuracy of approximately 10 km, 3-sigma. There will be at least two different landing sites ('01 and '03) selected in the MSP. However, there should be an option of having the '05 sample return mission land in a different site and the '05 mission should be equipped with a rover for two reasons. The reasoning behind this follows: '05 lander/rover package should have the option of going to an independent site from either '01 or '03 because predecessor missions (orbital) may locate the "Ultimate Site"; '05 needs a rover to either: (A) explore and sample this "ultimate site" for sample return; (B) retrieve samples from '01 or '03 rovers, as a contingency, in case these rovers malfunction and cannot negotiate the trek back to the sample return vehicle.

Description: The microbial fossil record encompasses a wide range of information, including cellular remains, stromatolites, biofabrics, trace fossils, biominerals and chemofossils. The preservation of fossils is strongly influenced by the physical, chemical and biological factors of the environment which, acting together, ultimately determine the types of information that will be captured and retained in the rock record. The critical factor in assessing the suitability of a site for a microbial fossil record is the paleoenvironment. The reconstruction of ancient sedimentary environments usually requires the integration of a wide variety of geological information, including the shape, geometry and internal structure of sedimentary deposits, their mineralogy, and geochemistry. For Mars, much of our knowledge about past environments is based on orbital imaging of geomorphic features. This evidence provides an important context and starting point for site selection. However, our knowledge of the martian surface is quite limited, and a major goal of the upcoming exploration effort is to reconstruct the history of Martian volatiles, climate, and hydrology as a context for the exploration for past or present life. Mineralogical mapping from orbit will be an important key in this effort. In exploring for evidence of past life, terrestrial experience suggests that the long-term preservation of biological information as fossils occurs under a fairly narrow range of geological conditions that are well known to paleontologists (1). In detrital sedimentary systems, microbial fossilization is favored by rapid burial in fine-grained, clay-rich sediments. In chemical sedimentary systems, preservation is enhanced by rapid entombment in fine-grained chemical precipitates. For long term preservation, host rocks must be composed of stable minerals that resist chemical weathering, and which form an impermeable matrix and closed chemical system that can protect biosignatures from alteration during subsequent diagenetic change or metamorphism. In this context, host rocks composed of highly ordered, chemically-stable mineral phases, like silica (forming cherts) or phosphate (forming phosphorites), are especially favored. Such lithologies tend to have very long crustal residence times and (along with carbonates and shales), are the most common host rocks for the Precambrian microfossil record on Earth. If we assume that a subsurface hydrosphere has been present throughout martian history, then life could have originated there at any time, perhaps emerging at the surface periodically when climate changes, induced by external forcing or endogenous processes (e.g. volcanism), allowed liquid water to exist at the surface. The recent discovery of subsurface chemolithoautotrophic organisms which are capable of synthesizing organic substrates from C02 and H2 liberated from the aqueous weathering of basalt, is especially. relevant as a model for martian life. While a subsurface habitable zone may yet exist on Mars, access to such environments will likely require drilling to depths of several kilometers. Given the technological challenge of deep drilling, this is unlikely to occur prior to human missions. So, even if there is extant life on Mars today in subsurface habitats, it may be much easier to find its fossil counterparts in ancient deposits exposed at the surface. In exploring for a fossil record in subsurface environments on Mars there are several geological situations that may provide access to the appropriate materials. These include 1) ejecta from impact craters, 2) talus slopes, debris flows or alluvial fans developed below the walls of deep canyons, and 3) the deposits of outflood channels. Examples of aqueous mineral deposits of formed in subsurface environments that could harbor a microbial fossil record include such things as cements in detrital sedimentary rocks, low temperature diagenetic minerals deposited in veins, or filling vesicles in volcanic rocks, and hydrothermal deposits formed below the upper temperature limit for life (about 160 degrees C). There are many sites within the present latitudinal constraints for the 2001 mission (15 deg S to 30 deg N) that meet these requirements. But the practical problem with these kinds of deposits is that they tend to be disseminated, making up only a small percentage of a host rock. Even with mineralogical information provided by the Thermal Emission Spectrometer (TES) presently in orbit around Mars, predicting their occurrence ahead of time may be quite difficult. The deposits of surficial aqueous sedimentary systems are likely to provide the largest targets for site selection in 2001. Of these, the deposits of hydrothermal systems (subaerial and subaqueous thermal springs) have been discussed previously. It is likely that hydrothermal systems were widespread on Mars early in its history and a number of common geo-tectonic settings on Mars are likely to have hosted hydrothermal activity. Most of these are represented within the latitudinal constraints presently identified for 2001. However, the deposits of surface spring systems are likely to be difficult to find as well. On Earth, exposure areas for hydrothermal spring mounds are typically a few square kms, less than a single TES pixel. But such deposits may be quite abundant within some volcanic terrains, It is estimated, for example, that between 15-20% of the floor of Yellowstone caldera is covered by thermal spring deposits. In such abundances, subaerial sinters could well be detected by TES. Where exposed, the shallow subsurface portions of these systems may be quite a lot larger (perhaps tens of square kms), although (as noted above) mineralization may be finely disseminated in the basement rock, making remote detection more difficult. Paleolake Basins. There are a large number of potential paleolake basins on Mars (inclusive of impact craters and volcanic calderas) that have been previously identified using Viking images. Most of these lie in the southern highlands beyond the l5 deg S constraint for 2001. However, deposits of paleolakes may offer the largest and most easily identified exopaleontological targets from orbit. Based on a variety of arguments, some workers have suggested that there was once an ancient ocean on the northern plains, and some sites of interest (potential shoreline terraces) fall within the 30 deg N constraint. From a paleontological standpoint the most interesting places of this type are terminal paleolake basins which are likely to have been both saline and alkaline. Models by Schaefer suggest such environments could be widespread on Mars. The conditions in terminal lake basin settings favor widespread chemical sedimentation, an important condition for microbial fossilization. Important lithological targets for a microbial fossil record in terminal lake basins include spring-deposited carbonates, shoreline cements, a wide variety of evaporite minerals and fine-grained detrital sediments including shales, marls, and water-lain volcanic ash deposits. In developing a strategy to explore for ancient hydrothermal deposits on Mars, we can learn from the methods that have been developed by explorationists to explore for economic mineral deposits on Earth. Due to their simple mineralogy, hydrothermal deposits can often be detected using remote sensing methods. Common thermal spring mineral assemblages include silica, carbonate, and various metallic oxides and sulfides. But there are also a number of diagnostic silicate minerals, including clays, formed by the hydrothermal alteration of country rocks. These hydrothermal minerals have characteristic spectral signatures that could be detected from Mars orbit using high resolution infrared remote sensing methods. In playa lake settings, evaporite deposits often form a predictable "bull's eye" pattern with carbonates being deposited in marginal basin areas, and sulfates and halides occurring progressively more basinward. The floors of some impact craters on Mars, such as "White Rock" and Bequeral Crater (see Oxia Palus NE, Site 148), have floor deposits that could be evaporites, inclusive of carbonates. Evaporite minerals possess characteristic spectral signatures in the infrared and could similarly be identified from Mars orbit using high resolution remote sensing methods. Clearly, utilization of TES data will be important for optimizing site selection for Exopaleontology, and every effort should be made to benefit from that data before a final decision is made.

Description: The successful landing of the Mars Pathfinder spacecraft on Mars allows the review of the process of selecting the landing site and assessing predictions made for the site based on Viking and Earth-based data. Selection of the landing site for Mars Pathfinder was a two-phase process. The first phase took place from October 1993 to June 1994 and involved: initial identification of engineering constraints, definition of environmental conditions at the site for spacecraft design, and evaluation of the scientific potential of different landing sites. This phase culminated with the first "Mars Pathfinder Landing Site Workshop", held at the Lunar and Planetary Institute in Houston, Texas on April 18-19, 1994, in which suggested approaches and landing sites were solicited from the entire scientific community. A preliminary site was selected by the project for design purposes in June 1994. The second phase took place from July 1994 to March 1996 and involved: developing criteria for evaluating site safety using images and remote sensing data, testing of the spacecraft and landing subsystems (with design improvements) to establish quantitative engineering constraints on landing site characteristics, evaluating all potential landing sites on Mars, and certification of the site by the project. This phase included a second open workshop, "Mars Pathfinder Landing Site Workshop II: Characteristics of the Ares Vallis Region and Field Trips in the Channeled Scabland, Washington" held in Spokane and Moses Lake September 24-30, 1995 and formal acceptance of the site by NASA Headquarters. Engineering constraints on Pathfinder landing sites were developed from the initial design of the spacecraft and the entry, descent and landing scenario. The site must be within 5 degrees of the subsolar latitude at the time of landing (15N for maximum solar power and flexible communications with Earth. It also must be below 0 km elevation to enable enough time for the parachute to bring the lander to the proper terminal velocity for landing. The entire landing ellipse, which is 70 km by 200 km due to navigational, ephemeris and atmospheric uncertainties, must be free of steep slopes, scarps and obvious hazards in Viking orbiter images, have acceptable radar reflectivity, moderate rock abundances and have little or no dust. Scientific considerations of the Mars Pathfinder payload and mission indicate that analyses of "grab bag" samples at the mouths of outflow channels can offer a first order assessment of a variety of rock types on Mars. Highland sites offer the advantage of in situ analysis of ancient rocks on Mars that record crustal differentiation and the nature of the early environment. Dark gray sites offer the potential of analyzing unweathered and unoxidized materials. Following a general assessment of the safety of different sites, a preliminary selection of a "grab bag" site was made. This site, Ares Vallis, is near the mouth of an outflow channel that may contain ancient Noachian terrain, Hesperian ridged plains, and reworked channel materials. All potential landing sites on Mars that met basic safety criteria were analyzed in detail. Sites (100 by 200 km target ellipses) were considered safe if they were below 0 km elevation, were free of obvious hazards (high relief surface features) in high-resolution (〈 50 m/pixel) Viking orbiter images and had acceptable reflectivity and roughness at radar wavelengths, high thermal inertia, moderate rock abundance, low red to violet ratio, and low albedo. Only 4 sites on Mars met all the above criteria, which included 1995 opposition 3.5 cm delay-Doppler radar data. Complete data were evaluated for 7 sites and the Viking landing sites for comparison for all the above criteria as well as crater abundance, hill and mesa abundance, slopes over meter to kilometer scales, low altitude winds (from global circulation models and slopes), the size-frequency distribution of large rocks, as well as rover trafficability and science potential. Discussion of potential hazards at Ares Vallis using a variety of data sets (including radar) at a second open workshop, indicated this site cannot be shown to be any more hazardous than the Viking landing sites. Field trips to the Channeled Scabland and the Ephrata Fan, analogs for Ares Vallis and the landing site, respectively, provided valuable insight into possible geologic processes and potential surface characteristics. Three sites met all the data requirements and safety criteria for landing Pathfinder. Ares Vallis was selected by the project because it appeared acceptably safe (although it appeared to have greater rock abundances than other sites, its elevation was likely the best known) and offered the prospect of analyzing a variety of rock types expected to be deposited by catastrophic floods, which would enable addressing first-order scientific questions such as differentiation of the crust, the development of weathering products, and the nature of the early martian environment and its subsequent evolution. The selection was reviewed by an external board at a number of meetings and accepted, and the site was approved by NASA Headquarters. Data gathered by the Pathfinder lander' and rover provides the opportunity to test the predictions made for the site in the selection process based on remote observations from Earth, orbit, and the surface. The discussion below is taken from Golombek et al. to which the reader is referred for a more complete discussion and a complete list of references, which are omitted here for brevity. Many characteristics of the landing site are consistent with its being shaped and deposited by the Ares and Tiu catastrophic floods. The rocky surface is consistent a depositional plain comprising semi-rounded pebbles, cobbles and tabular boulders (some of which appear imbricated and/or inclined in the direction of flow) that appear similar to depositional plains in terrestrial catastrophic floods. The Twin Peaks appear to be streamlined hills in lander images, which is consistent with interpretations of larger hills in Viking orbiter images of the region that suggest the lander is on the flank of a broad, gentle ridge trending northeast from Twin Peaks. This ridge, which is the rise to the north of the lander, is aligned in the downstream direction from the Ares and Tiu Valles floods, and may be a debris tail deposited in the wake of the Twin Peaks. Channels visible throughout the scene may be a result of late stage drainage. As predicted by delay-Doppler radar measurements and tracking results, the average elevation of the center of the site was about the same as Viking Lander I relative to the 6.1 mbar geoid. The Doppler tracking and two-way ranging estimate for the elevation of the spacecraft is only 45 in lower than the Viking I Lander and within 100 in of that expected, which is within the uncertainties of the measurements. After landing, surface pressures and winds (5-10 m/s) were found to be similar to expectations based on Viking data, although temperatures were about 10 K warmer. The temperature profile below 50 km was also roughly 20 K warmer. As a result, predicted densities were 5% higher near the surface and up to 40% lower at 50 km but within the entry, descent and landing design margins. The populations of craters and small hills and the slopes of the hills measured in high-resolution (38 m/pixel) Viking orbiter images and the radar derived slopes of the landing site are all consistent with observations of these properties in the lander images. A rocky surface was expected from Viking Infra-Red Thermal Mapper (IRTM) observations and comparisons with the Viking landing sites. The observed cumulative fraction of area covered by rocks with diameters greater than 3 cm and heights greater than 0.5 in (potentially hazardous to landing) at Ares is similar to that predicted by IRTM observations and models of Viking lander and Earth analog rock size-frequency distributions. The IRTM prediction postulated an effective thermal inertia of 30 (10(exp -3) cgs units - cal/cubic cm/s(exp 0.5)/K) for the rock population, but we obtain a slightly different effective thermal inertia for the actual rock population. The validity of interpretations of radar echoes prior to landing are supported by a simple radar echo model, an estimate of the reflectivity of the soil from its bulk density, and the fraction of area covered by rocks. In the calculations, the soil produces the quasi-specular echo and the rocks produce the diffuse echo. The derived quasispecular cross section is comparable to the cross-sections and reflectivities reported for 3.5-cm wavelength observations. The model yields a diffuse echo that is modestly larger than the polarized diffuse echo reported for 3.5-cm wavelength observations. At 12.5-cm wavelength, similar rock populations at Ares and the Viking I site were expected because the diffuse echoes are comparable, but the large normal reflectivities suggests that bulk densities of the soils at depth are greater than those at the surface. We also obtain a fine-component inertia near 8.4 which agrees with the fine-component inertia of 8.7 (in 10(exp -3) cgs units) estimated from thermal observations from orbit by the IRTM; for this estimate, we used a bulk thermal inertia of 10.4 for the landing site, an effective thermal inertia near 40 (10(exp -3) cgs units) for the rock population, and a graphical representation of Kieffer's model. Color and albedo data for Ares suggested surfaces of materials at Ares Vallis would be relatively dust free or unweathered prior to landing compared with the materials at the Viking landing sites. This suggestion is supported by the abundance of relatively dark-gray rocks at Ares and their relative rarity at the Viking landing sites, where rocks are commonly coated with bright red dust. Finally, the 40 km long Ephrata Fan of the Channeled Scabland in Washington state, which was deposited where c

Description: The goals of field study on Mars are nothing less than to understand the processes and history of the planet at whatever level of detail is necessary. A manned mission gives us an unprecedented opportunity to use the immense power of the human mind to comprehend Mars in extraordinary detail. To take advantage of this opportunity, it is important to examine how we should approach the field study of Mars. In this effort, we are guided by over 200 years of field exploration experience on Earth as well as six manned missions exploring the Moon.

Description: Thermal barrier coatings are important, and in some instances a necessity, for high temperature applications such as combustor liners, and turbine vanes and rotating blades for current and advanced turbine engines. Some of the insulating materials used for coatings, such as zirconia that currently has widespread use, are partially transparent to thermal radiation. A translucent coating permits energy to be transported internally by radiation, thereby increasing the total energy transfer and acting like an increase in thermal conductivity. This degrades the insulating ability of the coating. Because of the strong dependence of radiant emission on temperature, internal radiative transfer effects are increased as temperatures are raised. Hence evaluating the significance of internal radiation is of importance as temperatures are increased to obtain higher efficiencies in advanced engines.

Description: Four research areas at the NASA Lewis Research Center involving the tribology of space mechanisms are highlighted. These areas include: soluble boundary lubrication additives for perfluoropolyether liquid lubricants, a Pennzane dewetting phenomenon, the effect of ODC-free bearing cleaning processes on bearing lifetimes, and the development of a new class of liquid lubricants based on silahydrocarbons.

Description: No abstract available

Description: Elevations from the Mars Orbiter Laser Altimeter (MOLA) have been used to construct a precise topographic map of the martian north polar region. The northern ice cap has a maximum elevation of 3 kilometers above its surroundings but lies within a 5-kilometer-deep hemispheric depression that is contiguous with the area into which most outflow channels emptied. Polar cap topography displays evidence of modification by ablation, flow, and wind and is consistent with a primarily H2O composition. Correlation of topography with images suggests that the cap was more spatially extensive in the past. The cap volume of 1.2 x 10(6) to 1.7 x 10(6) cubic kilometers is about half that of the Greenland ice cap. Clouds observed over the polar cap are likely composed of CO2 that condensed out of the atmosphere during northern hemisphere winter. Many clouds exhibit dynamical structure likely caused by the interaction of propagating wave fronts with surface topography.

Description: Ongoing studies of the evolution of the Martian cratered highlands, the nature of the planet's early climate, and the recent announcement of possible evidence of ancient life in the ALH 84001 meteorite have reinvigorated interest in the conditions that prevailed on Mars during its first billion years of geologic history. To address this interest and assess our current understanding of these issues, the Lunar and Planetary Institute hosted a 4-day Conference on Early Mars in Houston in April of 1997. The papers contained in this special section are a product of that meeting. The purpose of the conference was twofold: (1) to consider how impacts, volcanism, and the presence of abundant water affected the physical and chemical environment that existed on Mars 4 Gyr ago, particularly as it related to the nature of the global climate, the origin of the valley networks, the geologic and mineralogic evolution of the surface, the aqueous geochemistry of groundwater, and the existence of local environments that may have been conducive to the development of indigenous life and the preservation of its signature in the geologic record; and (2) to discuss what observations or experiments might he included in future spacecraft missions to test the ideas and expectations arising from purpose 1. While pertinent issues of early atmospheric and solar evolution were also addressed, the primary discussion at the conference focused on the evidence and constraints provided by the geologic records of Earth, the Moon, and Mars and analysis of the SNC meteorites. The papers contained in this special section span the full range of these topics, including the stability of the early atmosphere to erosion by the solar wind, the geologic environment from which the SNC meteorites originated, geomorphic evidence regarding the nature of the early Martian climate and hydrologic cycle, the potential impact of the past and present environment on the preserved signature of ancient life, and a discussion of the capabilities of a lander-based X ray diffraction and fluorescence instrument to assess the potential for past fossilization from the mineralogy of the current local surface environment. The issues raised at the conference, and by the papers included in this special section, will be the focus of ongoing attention as the intensity and scope of Mars exploration increases over the next decade.

Description: Thick thermal barrier coating systems in a diesel engine experience severe thermal low cycle fatigue (LCF) and high cycle fatigue (HCF) during engine operation. In this paper, the mechanisms of fatigue crack initiation and propagation in a ZrO2-8wt% Y2O3 thermal barrier coating, under simulated engine thermal LCF and HCF conditions, are investigated using a high power CO2 laser. Experiments showed that the combined LCF-HCF tests induced more severe coating surface cracking, microspallation and accelerated crack growth, as compared to the pure LCF test. Lateral crack branching and the ceramic/bond coat interface delaminations were also facilitated by HCF thermal loads, even in the absence of severe interfacial oxidation. Fatigue damage at crack wake surfaces, due to such phenomena as asperity/debris contact induced cracking and splat pull-out bending during cycling, was observed especially for the combined LCF-HCF tests. It is found that the failure associated with LCF is closely related to coating sintering and creep at high temperatures, which induce tensile stresses in the coating after cooling. The failure associated with HCF process, however, is mainly associated with a surface wedging mechanism. The interaction between the LCF, HCF and ceramic coating creep, and the relative importance of LCF and HCF in crack propagation are also discussed based on the experimental evidence.

Description: A reaction-bonded silicon carbide (RB-SiC) ceramic material (Carborundum's Cerastar RB-SIC) has been joined using a reaction forming approach. Microstructure and mechanical properties of three types of reaction-formed joints (350 micron, 50-55 micron, and 20-25 micron thick) have been evaluated. Thick (approximately 350 micron) joints consist mainly of silicon with a small amount of silicon carbide. The flexural strength of thick joints is about 44 plus or minus 2 MPa, and fracture always occurs at the joints. The microscopic examination of fracture surfaces of specimens with thick joints tested at room temperature revealed the failure mode to be typically brittle. Thin joints (〈50-55 micron) consist of silicon carbide and silicon phases. The room and high temperature flexural strengths of thin (〈50-55 micron) reaction-formed joints have been found to be at least equal to that of the bulk Cerastar RB-SIC materials because the flexure bars fracture away from the joint regions. In this case, the fracture origins appear to be inhomogeneities inside the parent material. This was always found to be the case for thin joints tested at temperatures up to 1350C in air. This observation suggests that the strength of Cerastar RB-SIC material containing a thin joint is not limited by the joint strength but by the strength of the bulk (parent) materials.

Description: As an ongoing effort to develop structural adhesives for high-performance aerospace applications, recent work has focused on phenylethynyl terminated imide (PETI) oligomers. The work reported herein involves the synthesis and characterization of a series of phenylethynyl containing oligomers designated LARC(TM) MPEI (modified phenylethynyl imide). These oligomers presumably contain mixtures of linear, branched and star-shaped molecules. The fully imidized polymers exhibited minimum melt viscosities as low as 600 poise at 335 C, significantly lower than equivalent molecular weight linear materials. Ti/Ti lap shear specimens processed at 288 C under 15 psi showed tensile shear strengths as high as approx. 6000 psi and 5200 psi at ambient temperature and 177 C respectively. The chemistry and properties of these new MPEIs are presented and compared with an optimized linear PETI, LARC(TM)PETI-5.

Description: As part of a program to develop high-performance/high-temperature structural resins for aeronautical applications, imide oligomers containing pendent and terminal phenylethynyl groups were prepared, characterized and the cured resins evaluated as composite matrices. The oligomers were prepared at a calculated number-average molecular weight of 5000 g/mol and contained 15-20 mol% pendent phenylethynyl groups. In previous work, an oligomer containing pendent and terminal phenylethynyl groups exhibited a high glass transition temperature (approximately 313 C), and laminates therefrom exhibited high compressive properties, but processability, fracture toughness, microcrack resistance and damage tolerance were less than desired. In an attempt to improve these deficiencies, modifications in the oligomeric backbone involving the incorporation of 1,3-bis(3-aminophenoxy)benzene were investigated as a means of improving processability and toughness without detracting from the high glass transition temperature and high compressive properties. The amide acid oligomeric solutions were prepared in N-methyl-2-pyrrolidinone and were subsequently processed into imide powder, thin films, adhesive tape and carbon fiber prepreg. Neat resin plaques were fabricated from imide powder by compression moulding. The maximum processing pressure was 1.4 MPa and the cure temperature ranged from 350 to 371 C for 1 h for the mouldings, adhesives, films and composites. The properties of the 1,3-bis(3-aniinophenoxy)benzene modified cured imide oligomers containing pendent and terminal phenylethynyl groups are compared with those of previously prepared oligomers containing pendent and terminal phenylethynyl groups of similar composition and molecular weight.

Description: The rotation of the Moon is influenced by solid-body tides and interaction at a liquid-core/solid-mantle boundary. The Lunar Laser Ranging (LLR) data are sensitive to variations in lunar rotation. Analysis of those ranges reveals four dissipation periodicities in the rotation. These signatures can be explained with the combined effects of tide plus core, but not with either alone. The fluid core detection exceeds three times its uncertainty. The inferred core radius has a 1 -sigma upper limit of 352 km for iron and up to 374 km if sulfur is present. The tidal dissipation is strong, Q at one month is 37 +/- 5 .Q increases for longer periods and is 60 (-15, +40) at one year.Dynamical evidence for a fluid lunar core has previously been presented. These-earlier solutions included three dissipation parameters. New solutions benefit from additional LLR data and an improved gravity field from Doppler tracking of Lunar Prospector. Five dissipation parameters are now solved for. There are several options for dissipation parameters: a core coupling parameter, a time delay for tidal distortion of the moments of inertia, and five periodic terms in the rotation angles. Solutions with different combinations of these are compatible (a theory relates K/C and time delay to a series of periodic terms). The solutions used K/C, time delay, and one periodic term. When dissipation signatures at five rotation frequencies are solved for, four amplitudes (4 to 263 milliarcseconds) are detected above the noise. Attempts to explain these results using either tides alone or core alone fail (less than 3(sigma) discrepancy for the former and 9(sigma), for the latter). A combination of tides and liquid core matches the results well.

Description: A series of polyimides derived from a newly synthesized diamine, namely, 4,4-bis(4-aminophenoxy)-2,2-dimethylbiphenyl (BAPD), were developed and characterized. Their physical and thermal properties were compared to polyimides based on'commercially available 2,2-bis(4-(4-aminophenoxy)phenyl)propane (BAPP).

Description: Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence, which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. The basic photophysics, calibration, accuracy and time response of a luminescent paint is described followed by applications in low speed, transonic, supersonic and cryogenic wind tunnels and in rotating machinery.

Description: We have previously demonstrated for the Thaumasia region of Mars that: (1) valley formation peaked during the Noachian and declined substantially during the Hesperian and Amazonian Periods and (2) valleys, many of which form networking systems, largely occur near volcanoes, highly faulted terrains, and large impact craters of similar age, thus suggesting hydrothermal activity. In Tanaka et al, the various hypotheses for valley formation on Mars are presented, and a geologic explanation for valley erosion in the Thaumasia region is given that "best fits" the region's geographic and geologic datasets. That comprehensive GIS-based investigation suggests that hydrothermal and seismic activity were the primary causes of valley formation in the Thaumasia region; the data make widespread precipitation less likely as a major factor in valley formation, except perhaps during the Early Noachian, for which much of the geologic record has been destroyed. Based on the reconstruction of the stratigraphic, tectonic, volcanic, and erosional histories and the close association of valleys in time and space with Noachian to Early Hesperian volcanoes and rift systems and Hesperian to Early Amazonian impact craters less than 50 km in diameter, we propose 13 sites of hydrothermal activity within the Thaumasia region; these are the best examples of valleys associated with these geologic features, but there are other less pronounced correlations elsewhere in the region.

Description: During the first reconaissence of the satellites of the outer solar system conducted by the Voyager missions (1979-1989), a surprising diversity of unusual geologic landforms were observed, in some cases with bewildering complexity (e.g., Triton). Impact features were certainly expected but the variety of volcanic, diapiric, tectonic, impact, and erosional landforms was only remotely suggested by some early theoretical works. These diagnostic features are manifestations of the internal composition, thermal history, and dynamical evolution of these bodies. It is the job of the geologist to interpret the morphology, stratigraphy, and composition of these deposits and structures to ascertain what materials were mobilized in the interior, in what amount, and the mechanism and cause of their mobilization. In this chapter, we review what is know about these features and what constraints can be placed on composition and thermal history. Particular emphasis is placed on volcanic features, as these are most directly related to satellite composition and thermal history. The surface spectra, high albedos, and low bulk densities of the satellites of the outer solar system indicate that water and other ices are abundant on these bodies, particularly on their surfaces. Ices, particularly water ice, are less dense than silicates and will tend to float and form crusts during differentiation or partial melting of the interior. Ices therefore take the place of silicates as 'crust-forming' minerals and dominate geologic processes on icy satellites. Melted ices form magma bodies, and sometimes are extruded as lavas, an unusual but still valid perspective for terrestrial geologists. The unusual properties of some ices, including their low melting temperatures, and low strengths (as well as the decrease in density on the freezing of water ice), will ultimately be very important in interpreting this record.

Description: LARC(Trademark) MPEI-1 (Langley Research Center(Trademark) modified phenylethynyl imide-1) phenylethynyl containing aromatic polymide, is based on the reaction of biphenyl dianhydride (BPDA), 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy)benzene (APB), 2,4,6-triaminopyrimidine (TAP) and 4-phenylethynyl phthalic anhydride (PEPA), presumably resulting in a mixture of linear, branched and star shaped phenylethynyl containing imides which was evaluated as a matrix for high-performance composites. The poly(amid acid) solution of MPEI-1 in N-methypyrrolidinone was synthesized at 35% and 42% solids. Unidirectional prepreg was fabricated from these solutions and Hercules IM7 carbon fiber utilizing NASA- Langley's multipurpose prepreg machine. The temperature-dependent volatile depletion rates, thermal crystallization behavior and resin theology were characterized. Based on this information, a composite molding cycle was developed which yielded well consolidated, void-free laminates. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. These mechanical properties are compared with those of IM7/LARC(Trademark) PETI-5 composites.

Description: Polyimides are finding increased applications in microelectronics due to their high thermal stability, good chemical resistance, good adhesion, low moisture absorption, good mechanical properties, and low coefficient of thermal expansion (CTE). Four series of random copolyimides were synthesized and characterized for potential application as encapsulants, stress-relief layers, and interlevel dielectrics. Several candidates exhibited good combinations of physical and mechanical properties with inherent viscosities from 1.21 to 1.42 dL/g, T(sub g)'s ranging from 251 to 277 C, 10% weight loss temperatures between 503 and 527 C, and CTEs ranging from 33 to 39 ppm/deg C. Mechanical properties at room temperature for the best candidates included tensile strengths of 17.8-21.3 ksi, moduli between 388 and 506 ksi, and elongations of 11-43%. Moisture absorption for these copolyimides ranged between 0.85 and 1.38 wt %.

Description: A Space Act Agreement between Kennedy Space Center and Surtreat Southeast, Inc., resulted in a new treatment that keeps buildings from corroding away over time. Structural corrosion is a multi-billion dollar problem in the United States. The agreement merged Kennedy Space Center's research into electrical treatments of structural corrosion with chemical processes developed by Surtreat. Combining NASA and Surtreat technologies has resulted in a unique process with broad corrosion-control applications.

Description: Imi-Tech Corporation, in cooperation with Johnson Space Center, introduced the Solimide AC-500 series of polyimide foam products designed to meet the needs of the aircraft/aerospace industry. These foams accomodate the requirements of state-of-the-art insulation systems. Solimide polyimide foams are currently used in defense, industrial and commercial applications.

Description: Galileo, the first artificial satellite of an outer planet, has been orbiting Jupiter since Dec 7, 1995. The spacecraft encounters one of the four Galilean satellites on each orbit.

Description: The Mars Pathfinder mission required new capabilities and adaptation of existing capabilities in order to support science analysis and flight operations requirements imposed by the in-situ nature of the mission.

Description: Develop battery that will meet DS-2 power requirements under specified operational, environmental, and life requirements.

Description: In this paper, the rover navigation performance is analyzed on the basis of received rover telemetry, rover uplink commands and stereo images captured by the lander cameras.

Description: There are significant international efforts underway to place mobile robots (rovers) on the surface of Mars.

Description: WFPC2/HST images of Saturn's far-ultraviolet aurora reveal emissions confined to a narrow band of latitudes near Saturn's north and south poles. The aurorae are most prominent in the morning sector with patterns that appear fixed in local time.

Description: The Lunar Prospector (LP) spacecraft has provided the first polar low latitude measurement of the lunar gravity field and as a result gives significant improvement in the lunar gravity field model.

Description: A study of several Harris current sheet type Euler potential models of Jupiters magnetosphere is presented.

Description: Studies of the Earth with the ATS-5, ATS-6, and SCATHA spacecraft led to the development of several simple tools for predicting the potentials to be expected on a spacecraft in the space environment.

Description: SRS Technologies is currently the only company licensed by Langley Research Center to produce colorless polyimides. They currently produce two polyimides, the LaRC-CP1 and LaRC-CP2 developed by Langley Research Center. These polyimides offer many advantages over other commercially available materials including excellent thermal stability, radiation resistance, solubility, and transparency. The SRS polyimides can be used in laminates, films, molded parts, and stock shapes. The polyimide technology has also helped the company further their development of solar arrays.

Description: Advanced Ceramics Research (ACR) of Tucson, Arizona, researches transforming scientific concepts into technological achievement. Through the SBIR (Small Business Innovative Research) program, ACR developed a high pressure and temperature fused deposition system, a prototyping system that is known as extrusion freeform fabrication. This system is useful in manufacturing prosthetics. ACR also developed a three-dimensional rapid prototyping process in which physical models are quickly created directly from computer generated models. Marshall Space Flight Center also contracted ACR to fabricate a set of ceramic engines to be appraised for a solar thermal rocket engine test program.

Description: Under a NASA SBIR (Small Business Innovative Research) contract with Johnson Space Center, Aspen Systems developed aerogel-based superinsulation. This super-insulation is an innovative, flexible cryogenic insulation with extremely low thermal conductivity. Potential commercial uses include cryogenic applications in the transportation, storage and transfer of cryogens; near room-temperature applications such as refrigerator insulation; and elevated temperature applications such as insulations for high- temperature industrial processes and furnaces.

Description: We have installed a large-format CCD camera on the 0.6 meter telescope at JPL's Table Mountain Observatory and used it to obtain high-accuracy astrometric obserations of asteroids and other solar system targets of interest.

Description: The Megallan Doppler radiometric tracking data provides unprecedented precision for spacecraft based gravity measurements with the maximum resolution approaching spherical harmonic degree and order 180 in selected equatorial regions.

Description: The effects of the sporadic meteroid environment on interplanetary spacecraft have an inportant impact on mission design. This paper describes a reformulation of the Divine interplanetary meteroid model, called METEM, that is capable of estimating many of those effects.

Description: In 1992, Dr. Wes Huntress challenged the JPL staff to undertake the first of NASA's new Discovery Program missions; Pathfinder.

Description: Viking infrared thermal mapping (IRTM) and bistatic radar data suggest that the bulk density of the erg material is much lower than that of the average Martian surface or of dark dunes at lower latitudes.

Description: The purpose of this paper is to propose a link layer standard for bi-directional telecommunication for in-situ links for data transfer between landers, rovers, and orbiters based upon the CCSDS Telecommand Recommendation.

Description: Lunar prospector, the third mission in the faster, better, cheaper NASA Discovery program, was successfully launched from Cape Canaveral on Januray 6, 1998.

Description: Immersive environments are just beginning to be used to support mission operations at the Jet Propulsion Laboratory. This technology contributed to the Mars Pathfinder Mission in planning sorties for the Sojourner rover.

Description: This paper will describe the system developed to support Mars Pathfinder, the technology that was used to provide sophisticated products at very low cost, and the variety of data products used to support Mars Pathfinder operations. This paper represents one phase of work performed at the Jet Propulsion Laboratory, California Instittue of Technology, under a contract with National Aeronautics and Space Administration.

Description: This paper describes the results of new analyses and mission/system designs for a low cost Neptune Orbiter mission. Science and measurement objectives, instrumentation, and mission/system design options are described and reflect an aggressive approach to the application of new advanced technologies expected to be available and developed over the next five to ten years.

Description: This paper describes the results of new analyses and mission/system designs for low cost Advanced Jupiter Probes. Science and mesurement objectives, instrumentation, entry probe design, and mission/system design options are described and reflect an aggressive approach to the application of new advance technologies expected to be both available and developed over the next ten years.

Description: Photometric observations of the five medium-sized satellites of Saturn were obtained with the 60-inch telescope at Palomar Mountain Observatory during the Ring Plane Crossing in August 1995.

Description: The Web Interface for Telescience (WITS) is an Internet-based tool that the Mars Pathfinder mission used for both mission operations at JPL and public outreach.

Description: NASA and Japan's Institute of Space and Astronautical Science (ISAS) have agreed to cooperate on the first mission to collect samples from the surface of an asteroid and return them to Earth for in-depth study.

Description: The propulsion requirements for ascent from the surface of Mars as part of a Mars sample return mission exceed the capabilities of current state-of-the-art chemical propulsion systems.

Description: Large topographic rises on Venus have previously been classified as volcano-dominated, rift-dominated and corona-dominated.

Description: This paper describes preliminary navigation analyses for the proposed Europa Orbiter mission.

Description: Careful examination of 28,460 selected Wide Field and Planetary Camera 2 (WFPC2) long exposures from 1994, 1995 and early 1996 has revealed trails of 96 distinct moving objects.