ALBERT

Description: Lag correlation statistics was used to study intraseasonal variations of upper and lower-level zonal winds, outgoing longwave radiation, and globally averaged angular momentum (GAM) for northern summers of 1977-1984. The temporal and spatial distribution of surface wind stress in the tropics and its relationship with zonal wind anomalies were studied to assess the impact of surface frictional drag on the atmospheric angular momentum. The 30-60 day GAM fluctuation is shown to be accompanied by zonal propagation of convection and 850 mb zonal wind anomalies in the tropical belt. The climatological zonal wind in the tropics affects the magnitude of wind stress anomalies. It is suggested that momentum exchange between the lower and upper troposphere may occur in regions of active convection via vertical momentum transport. The tropical central Pacific is considered to play a key role in linking the atmosphere and the earth through angular momentum exchange on intraseasonal time scales.

Description: A collaborative rain-observation experiment using an airborne rain radar was conducted between Communications Research Laboratory (CRL) and Goddard Space Flight Center (GSFC)/NASA. CRL provided an airborne rain-radar/radiometer system and GSFC/NASA provided a NASA P3-A aircraft. Airborne or spaceborne rain-radar echoes have large sea or land-surface echoes. These surface echoes yield rain-estimation algorithms using rain attenuation. The experiment demonstrated the potential of the rain-estimation techniques using rain attenuation.

Description: Aluminum plates of various length/width ratios loaded in compression are examined analytically in terms of buckling and postbuckling for comparison with classical theory. The plates are considered to be subjected to longitudinal compressive displacement with no edge stress and are assumed to be simply supported at the side edges. The average longitudinal direct stresses are computed to plot characteristic curves by means of the following theories: 3D flexibility, higher-order shear deformation, first-order shear deformation, and classical von Karman. The 3D flexibility approach yields the lowest results with more unknowns than the higher-order shear-deformation method. The 3D flexibility approach is considered to be the most accurate, and it is shown that the calculated resultants and displacements tend to vary when consideration is given to the effects of transverse shear.

Description: Present interest in hypersonic vehicles has resulted in a renewed interest in thermal stress analysis of airframe structures. While there are numerous texts and papers on thermal stress analysis, practical examples and experience on light gage aircraft structures are fairly limited. A research program has been undertaken at General Dynamics to demonstrate the present state of the art, verify methods of analysis, gain experience in their use, and develop engineering judgement in thermal stress analysis. The approach for this project has been to conduct a series of analyses of this sample problem and compare analysis results with test data. This comparison will give an idea of how to use our present methods of thermal stress analysis, and how accurate we can expect them to be.

Description: This paper presents the fuzzy dynamical reliability and failure probability as well as the basic principles and the analytical method of loss assessment for nonlinear seismic steel structures. Also presented is the optimization formulation and a numerical example for double objectives, initial construction cost and expected failure loss, and dynamical reliability constraints. The earthquake ground motion is based on a stationary filtered non-white noise and the fuzzy damage grade is described by damage index.

Description: Effective methods of approximate eigensolution reanalysis of modified nonclassically damped structures are developed. For structures with passive or active discrete damping devices or with damping treatment, the system becomes nonproportionally damped and the computation of its dynamic responses may require the use of complex modes. For larger systems, the computation of complex modes is very expensive. Thus it is desirable to have approximate reanalysis techniques for the efficient evaluation of the effect of design changes. In recent years, the assumed mode reanalysis method was successfully applied to minimum weight design of undamped structures with natural frequency constraints. The accuracy of the assumed mode reanalysis method can be improved dramatically if the global approximation function includes the normal modes of the original system and their derivatives. This approach was demonstrated to be effective even for a system with shape changes. The approach used by Noor et al. for eigensolution reanalysis of undamped structures is extended to treat a nonclassically damped system.

Description: With structural design in mind, a new unified variational model has been developed which represents the mechanics of deformation elasto-plasticity with unilateral contact conditions. For a design problem formulated as maximization of the load carrying capacity of a structure under certain constraints, the unified model allows for a simultaneous analysis and design synthesis for a whole range of mechanical behavior.

Description: The real benefit of structural optimization techniques is in the application of these techniques to large structures such as full vehicles or full aircraft. For these structures, however, the sequential computer's time and memory requirements prohibit the solutions. With the rapid development of parallel computers, parallel processing of large scale structural optimization problems is achievable. In this paper we discuss the parallel processing of structural optimization problems with parallel structural analysis. Two different types of interface between the optimization and analysis routines are developed and tested.

Description: In most structural optimization problems the implicit behavior constraints are evaluated for successive modifications in the design. For each trial design, the analysis equations must be solved and the multiple repeated analyses usually involve extensive computational effort. This difficulty motivated several studies on explicit approximations of the structural behavior in terms of the design variables. The latter approach can considerably reduce the amount of computations, but the quality of the approximations might not be sufficient. Many of the approximate behavior models proposed in the past are valid only for relatively small changes in the design variables. The accuracy of the results is often insufficient for large changes in the design. The object of this study is to present efficient and high quality approximations of the structural behavior. It will be shown that the quality of the approximations can greatly be improved by combining scaling of the initial design, using intervening variables, and scaling a set of fictitious loads. Integrating these means, a powerful solution procedure can be introduced. In addition, the errors in satisfying the analysis equations can readily be evaluated. A numerical example illustrates the solution methodology and the effectiveness of the proposed approach.

Description: The weight savings due to usage of composite materials in aircraft structural applications is well known. Significant weight and cost benefits are achievable by developing structurally tailored concepts and efficiently integrating them with suitable material and manufacturing technologies. The proposed paper will describe such an efficient concept for application to primary aircraft structures.

Description: This paper first presents a brief review on the application of optimization and active control of seismic structures along with some of the author's recent work. It then assesses the practicality and future development of seismic structural optimization, and some practical problems associated with active control.

Description: The paper presents the theoretical bases and implementation techniques of sensitivity analyses for efficient structural optimization of large structures, based on finite element static and dynamic analysis methods. The sensitivity analyses have been implemented in conjunction with two methods for optimization, namely, the Mathematical Programming and Optimality Criteria methods. The paper discusses the implementation of the sensitivity analysis method into our in-house software package, AutoDesign.

Description: Ill-conditioned systems arising in analysis and optimization can display a high sensitivity to numerical precision for changes and errors in data input. Such data may be in the form of system parameter input or desired system response. The ill-conditioning referred to generally arises from the lack of sufficient independent data to define a complex system or the weak sensitivity of response to source input parameters. It is shown how small errors in data and assumed fixed and known parameters can lead to highly erroneous results in ill-conditioned linear algebraic equations. A simplified detection and correction of critical input data arising in the coefficient matrix and desired response (i.e., right hand side) is proposed.

Description: An identification procedure proposed by Shen and Taylor to determine the crack characteristics (location and size of the crack) from dynamic measurements is tested. This procedure was based on minimization of either the 'mean-square' measure of difference between measurement data (natural frequencies and mode shapes) and the corresponding predictions obtained from the computational model. The procedure is tested for simulated damage in the form of symmetric cracks in a simply-supported Bernoulli-Euler beam. The sensitivity of the solution of damage identification problems to the values of parameters that characterize damage is discussed. A sensitivity formula is derived.

Description: The issue of the utility of multilevel decomposition and optimization remains controversial. To date, only the structural optimization community has actively developed and promoted multilevel optimization techniques. However, even this community acknowledges that multilevel optimization is ideally suited for a rather limited set of problems. It is warned that decomposition typically requires eliminating local variables by using global variables and that this in turn causes ill-conditioning of the multilevel optimization by adding equality constraints. The purpose is to suggest a new multilevel optimization technique. This technique uses behavior variables, in addition to design variables and constraints, to decompose the problem. The new technique removes the need for equality constraints, simplifies the decomposition of the design problem, simplifies the programming task, and improves the convergence speed of multilevel optimization compared to conventional optimization.

Description: In recent years there have been several hierarchic multilevel optimization algorithms proposed and implemented in design studies. Equality constraints are often imposed between levels in these multilevel optimizations to maintain system and subsystem variable continuity. Equality constraints of this nature will be referred to as coupling equality constraints. In many implementation studies these coupling equality constraints have been handled indirectly. This indirect handling has been accomplished using the coupling equality constraints' explicit functional relations to eliminate design variables (generally at the subsystem level), with the resulting optimization taking place in a reduced design space. In one multilevel optimization study where the coupling equality constraints were handled directly, the researchers encountered numerical difficulties which prevented their multilevel optimization from reaching the same minimum found in conventional single level solutions. The researchers did not explain the exact nature of the numerical difficulties other than to associate them with the direct handling of the coupling equality constraints. The coupling equality constraints are handled directly, by employing the Generalized Reduced Gradient (GRG) method as the optimizer within a multilevel linear decomposition scheme based on the Sobieski hierarchic algorithm. Two engineering design examples are solved using this approach. The results show that the direct handling of coupling equality constraints in a multilevel optimization does not introduce any problems when the GRG method is employed as the internal optimizer. The optimums achieved are comparable to those achieved in single level solutions and in multilevel studies where the equality constraints have been handled indirectly.

Description: Reliability was determined for two degrading dynamic systems subject to random load processes. Damage is caused by loss of components for Daniels systems and crack extension for plates with cracks. The analysis accounted for the coupling between response and current damage state of the system. It is based on mean crossing rates of conditional processes and properties of diffusion models. Simple systems are used to illustrate proposed methods for estimating reliability.

Description: A passive vibration damping technique that is referred to as 'Non-Obstructive Particle Damping (NOPD)' is presented. The NOPD technique consists of making small diameter holes (or cavities) at appropriate locations inside vibrating structures and filling these holes to appropriate levels with particles which yield the maximum damping effectiveness for the desired mode (or modes). Powders, spherical shaped, metallic, non-metallic or liquid particles (or mixtures) with different densities, viscosities and adhesive or cohesive characteristics can be used.

Description: Recent results from sensitivity analysis for strain energy with anisotropic elasticity are applied to thickness and orientational design of laminated membranes. Primarily, the first order gradients of the total elastic energy are used in an optimality criteria based method. This traditional method is shown to give slow convergence with respect to design parameters, although the convergence of strain energy is very good. To get a deeper insight into this rather general characteristic, second order derivatives are included and it is shown how they can be obtained by first order sensitivity analysis. Examples of only thickness design, only orientational design, and combined thickness--orientational design are presented.

Description: The objective is to set up and analyze benchmark problems on multibody dynamics and to verify the predictions of two multibody computer simulation codes. TREETOPS and DISCOS have been used to run three example problems - one degree-of-freedom spring mass dashpot system, an inverted pendulum system, and a triple pendulum. To study the dynamics and control interaction, an inverted planar pendulum with an external body force and a torsional control spring was modeled as a hinge connected two-rigid body system. TREETOPS and DISCOS affected the time history simulation of this problem. System state space variables and their time derivatives from two simulation codes were compared.

Description: The non-linear dynamic analysis of large structures is always very time, effort and CPU consuming. Whenever possible the reduction of the size of the mathematical model involved is of main importance to speed up the computational procedures. Such reduction can be performed for the part of the structure which perform linearly. Most of the time, the classical Guyan reduction process is used. For non-linear dynamic process where the non-linearity is present at interfaces between different structures, Craig-Bampton models can provide a very rich information, and allow easy selection of the relevant modes with respect to the phenomenon driving the non-linearity. The paper presents the employment of Craig-Bampton models combined with Newmark direct integration for solving non-linear friction problems appearing at the interface between the Hubble Space Telescope and its solar arrays during in-orbit maneuvers. Theory, implementation in the FEM code ASKA, and practical results are shown.

Description: Structural optimization problems are mostly solved under constraints from statics, such as stresses, strains, or displacements under static loads. But in the design process, dynamic quantities like eigenfrequencies or accelerations under dynamic loads become more and more important. Therefore, it is obvious that constraints from dynamics must be considered in structural optimization packages. This paper addresses the dynamics branch in MBB-LAGRANGE. It will concentrate on two topics, namely on the different formulations for eigenfrequency constraints and on frequency response constraints. For the latter the necessity of a system reduction is emphasized. The methods implemented in LAGRANGE are presented and examples are given.

Description: This paper addresses the weight minimization of a circular plate-like structure which resulted in a 26 percent weight reduction. The optimization was performed numerically with the COPES/ADS program using the modified method of feasible directions. Design parameters were the inner thickness and outer thickness of the plate with constraints on maximum yield stress and maximum transverse displacement. Also, constraints were specified for the upper and lower bounds of the fundamental frequency and plate thicknesses. The MSC/NASTRAN finite element program was used for the evaluation of response variables. Original and final designs of the plate were tested using an Instron tension-compression machine to compare finite element results to measured strain data. The difference between finite element strain components and measured strain data was within engineering accuracy.

Description: Any optimization of structures for maximum stability or for maximum dynamic stiffness deals with an eigenvalue problem. The goal of this optimization is to raise the lowest eigenvalue (or eigenvalues) of the problem to its highest (optimal) level at a constant volume of the structure. Likely the lowest eigenvalue may be either inherently multi-modal or it can become multi-modal as a result of the optimization process. The multimodeness introduces some ambiguity to the eigenvalue problem and make the optimization difficult to handle. Thus far, only the simplest cases of multi-modal structures have been effectively optimized using rather elaborate analytical methods. Numerous publications report design of a minimum volume structure with different eigenvalues constraints, in which, however, the modality of the problem is assumed a priori. The method presented here utilizes a multi-modal optimality criteria and allows for inclusion of an arbitrary number of buckling or vibrations modes which might influence the optimization process. The real multi-modality of the problem, that is the number of modes participating in the final optimal design is determined iteratively. Because of a natural use of the FEM technique the method is easy to program and might be helpful in design of large flexible space structures.

Description: The structure-control system optimization problem is formulated with constraints on the closed-loop eigenvalues and the efficiency of the reduced order system. The feasibility of the approach is illustrated by designing the ACOSS-FOUR structure with a reduced order system and improving the efficiency characteristics of the structures-control system.

Description: In this paper an optimal design procedure is introduced to improve the overall performance of nonlinear framed structures. The design methodology presented here is a multiple-objective optimization procedure whose objective functions involve the buckling eigenvalues and eigenvectors of the structure. A constant volume with bounds on the design variables is used in conjunction with an optimality criterion approach. The method provides a general tool for solving complex design problems and generally leads to structures with better limit strength and stability. Many algorithms have been developed to improve the limit strength of structures. In most applications geometrically linear analysis is employed with the consequence that overall strength of the design is overestimated. Directly optimizing the limit load of the structure would require a full nonlinear analysis at each iteration which would be prohibitively expensive. The objective of this paper is to develop an algorithm that can improve the limit-load of geometrically nonlinear framed structures while avoiding the nonlinear analysis. One of the novelties of the new design methodology is its ability to efficiently model and design structures under multiple loading conditions. These loading conditions can be different factored loads or any kind of loads that can be applied to the structure simultaneously or independently. Attention is focused on optimal design of space framed structures. Three-dimensional design problems are more complicated to carry out, but they yield insight into real behavior of the structure and can help avoiding some of the problems that might appear in planar design procedure such as the need for out-of-plane buckling constraint. Although researchers in the field of structural engineering generally agree that optimum design of three-dimension building frames especially in the seismic regions would be beneficial, methods have been slow to emerge. Most of the research in this area has dealt with the optimization of truss and plane frame structures.

Description: In the design of complex built-up structures that are made of truss, beam, membrane, shell, and solid, there are five different kinds of design variables: material property, sizing, shape, configuration, and topological variables. Previous research has shown that the improvement in performances obtained by altering the configuration of structural components can be much more significant than those obtained when the geometry is assumed to be fixed. Using the variational approach, a unified design sensitivity was developed for the first three kinds of design variables, and was further extended recently in many structural analysis problems such as nonlinear, structural dynamics, and frequency response analysis. A continuum design sensitivity analysis method is developed for the configuration design variable of built-up structures.

Description: The scientific goals of TRMM are described. TRMM provides quantitative measurements of tropical rain which can improve the understanding of the global climate. TRMM can also help to improve techniques for measuring rainfall from space.

Description: This paper presents a simple new algorithm for constructing second-order models for any given flexible structure, with these models satisfying the constraint that each leading principal submatrix of the mass matrix must have a specified condition number. Now, the effects of rounding errors in practical computation generally increase with increasing condition number, i.e. as the matrix considered approaches singularity. Thus, the new models should prove useful for the systematic testing of the numerical properties of many algorithms in the dynamics and control of flexible structures.

Description: The determination of latent heat-flux variability using spaceborne sensors is discussed. Particular attention is given to the microwave sensors which have all weather capability. The retrieval of surface layer humidity, of wind speed and interfacial humidity, and of sensible heat flux are discussed. Both the indirect retrieval and direct retrieval of latent heat flux are considered.

Description: The stress-ratio algorithm associated with fully stressed design philosophy has been used as a convenient tool to achieve minimum weight design of strength-limited structures. The algorithm is effective and converges quickly for many cases. However, it presents extremely slow oscillatory iteration histories for plate-thickness design problems that involve transverse bending loads. Modification of the basic algorithm presented in this paper provides an effective remedy to this problem when both membrane and bending loads are present. The modified resizing algorithm requires numerical solutions of a fourth-order algebraic equation. No additional data, beyond the ordinary static analysis results, are required.

Description: A method for performing a global/local stress analysis is described and its capabilities are demonstrated. The method employs spline interpolation functions which satisfy the linear plate bending equation to determine displacements and rotations from a global model which are used as 'boundary conditions' for the local model. Then, the local model is analyzed independently of the global model of the structure. This approach can be used to determine local, detailed stress states for specific structural regions using independent, refined local models which exploit information from less-refined global models. The method presented is not restricted to having a priori knowledge of the location of the regions requiring local detailed stress analysis. This approach also reduces the computational effort necessary to obtain the detailed stress state. Criteria for applying the method are developed. The effectiveness of the method is demonstrated using a classical stress concentration problem and a graphite-epoxy blade-stiffened panel with a discontinuous stiffener.

Description: An analytical investigation is conducted to determine the shape of a growing delamination and the distribution of the energy release rate along the delamination front in a laminated composite double cantilever beam specimen. Distributions of the energy release rate for specimens with straight delamination fronts and delamination front contours for delaminations whose growth is governed by the fracture criterion that G = Gc at all points are predicted as a function of material properties and delamination length. The predicted delamination front contours are utilized to ascertain the effect of the changing shape of the delamination front on the value of the critical strain energy release rate as computed from double cantilever beam fracture toughness test data.

Description: An adaptive unstructured remeshing technique is applied to transient thermal-structural analysis. The effectiveness of the technique, together with the finite element method and an error estimation technique, is evaluated by two applications which have exact solutions: (1) the steady-state thermal analysis of a plate subjected to a highly localized surface heating, and (2) the transient thermal-structural analysis of a simulated convectively cooled leading edge subjected to a translating heat source. These applications demonstrate that the remeshing technique significantly reduces the problem size as well as the analysis solution error as compared to the results produced using standard structured meshes.

Description: Development of probabilistic structural analysis methods for hot structures is a major activity at NASA-Lewis, and consists of five program elements: (1) probabilistic loads, (2) probabilistic finite element analysis, (3) probabilistic material behavior, (4) assessment of reliability and risk, and (5) probabilistic structural performance evaluation. Attention is given to quantification of the effects of uncertainties for several variables on High Pressure Fuel Turbopump blade temperature, pressure, and torque of the Space Shuttle Main Engine; the evaluation of the cumulative distribution function for various structural response variables based on assumed uncertainties in primitive structural variables; evaluation of the failure probability; reliability and risk-cost assessment; and an outline of an emerging approach for eventual hot structures certification. Collectively, the results demonstrate that the structural durability/reliability of hot structural components can be effectively evaluated in a formal probabilistic framework. In addition, the approach can be readily extended to computationally simulate certification of hot structures for aerospace environments.

Description: This paper focuses on the design, analysis, and test of a high temperature structural panel, constructed of Ti-6-4, subjected to a variety of thermal and mechanical load conditions. A follow-on panel, constructed of TMC, is also discussed in less detail. The design constraints and test set-up are discussed, as well as the test methods that were used: the grid shadow moire method and a single gage force stiffness method. The agreement between the test data and analysis for this test program provides confidence in the methods that are currently being used to design structures for hypersonic vehicles. The agreement also suggests that postbuckled strength may potentially be used to reduce the vehicle weight.

Description: The time-dependent thermo-viscoplastic response of aerospace structures subjected to intense aerothermal loads is predicted using the finite-element method. The finite-element analysis uses the Bodner-Partom unified viscoplastic constitutive relations to determine rate-dependent nonlinear material behavior. The methodology is verified by comparison with experimental data and other numerical results for a uniaxially-loaded bar. The method is then used (1) to predict the structural response of a rectangular plate subjected to line heating along a centerline, and (2) to predict the thermal-structural response of a convectively-cooled engine cowl leading edge subjected to aerodynamic shock-shock interference heating. Compared to linear elastic analysis, the viscoplastic analysis results in lower peak stresses and regions of plastic deformations.

Description: An efficient procedure for obtaining the compatibility conditions of finite-element models involves the generation of both field and compatibility conditions from deformation-displacement relations, using (1) the compatibility bandwidth, and (2) the node-determinacy concept. A computer program thus structured will generate sparse and banded compatibility conditions for a structure that is idealized by the finite elements.

Description: Synoptic scale tropical plumes are analyzed using satellite data and outgoing longwave radiation data. The evolution of plumes is described and their precursor signals are examined. The horizontal moisture patterns of the plumes are compared with nonplume climatology, and the predictability of plumes based solely on satellite imagery is assessed. The results show that a plume evolves as a stationary, tropical, dry or moist dipole, separated by an exceptionally strong cloud or moisture gradient. Tropical plume evolution is accompanied by a systematic drying of the tropical eastern Pacific atmosphere before development, and moistening and increased cloudiness with development.

Description: Data from the Limb Infrared Monitor of the Stratosphere (LIMS) have been used to define zonally averaged basic-state temperature and zonal wind fields in the middle atmosphere for several periods during the winter of 1978-79. This basic state has been used to calculate the phase speeds, growth rates, and spatial structures of unstable modes using a linear, quasigeostrophic model. These results have been compared with temperature and ozone variance amplitudes from a spectral analysis of the same LIMS data. The comparison indicates that there is a close match between phase speeds for the most rapidly growing modes predicted by the model and phase speeds for statistically significant temperature and ozone variances. Both calculated and observed modes tend to be limited in latitudinal extent to a few tens of degrees and in vertical extent to about 10 km. These modes also tend to be nondispersive. Examples are given for the Southern Hemisphere near 0.25 mb (60 km) and for low latitudes of the Northern Hemisphere near 15 mb (30 km).

Description: A robust self-starting explicit architecture for computational structural dynamics is described. The proposed methodology involves expressing the governing equations of motion in conservation form and temporal discretization is accomplished in the spirit of the Lax-Wendroff type formulations. The development of the basic methodology is shown. Discretization in space is accomplished by introducing stress-based representations and employing the classical Galerkin scheme. Numerical test model results are presented which validate the architecture.

Description: Many mechanisms, including variations in solar radiation and atmospheric aerosol concentrations, compete with anthropogenic greenhouse gases as causes of global climate change. Comparisons of available data show that solar variability will not counteract greenhouse warming and that future observations will need to be made to quantify the role of tropospheric aerosols, for example.

Description: The problem addressed is that of obtaining reduced-order component models for use in simulating the dynamics of a multibody system. In certain cases, nonlinear system models may be constructed using linear dynamic models for each component, but allowing large angle motion between components. Without some form of model reduction, system models constructed in this manner may be too large for use in control system design and simulation trades. This paper analyzes one method of component model reduction that allows systems level requirements (e.g., capturing the effect of body 1 reaction wheel noise on body 2 camera pointing) to aid in the selection of the reduced-order component models. Briefly stated, important modes are selected at the system level and projected onto the components, and reduced-order components are then assembled into a reduced-order system model that retains the projected modes.

Description: The possibility of global-scale transitions between the Hadley and Rossby atmospheric regimes is investiated using a simple three-dimensional rotating spherical model without a boundary layer structure, bottom topography, or cumulus friction, and the expected occurrence of the Hadley to Rossby transition is demonstrated. It is shown that a transition from Hadley flow to wavenumber-5 Rossby flow is preferred, in agreement with standard baroclinic instability results. This result gives a reasonable Rossby wave bifurcation from the Hadley solution. For the cases examined, it was found that the upper symmetric Hadley regime does not exist and that the Hadley to Rossby transition depends on the values of the eddy viscosities.

Description: A procedure for the minimum weight design of helicopter rotor blades with constraints on multiple coupled flap-lag natural frequencies, autorotational inertia, and centrifugal stress is presented. Optimum designs are obtained for blades with both rectangular and tapered planforms and are compared within a reference blade. The effects of higher-frequency constraints and stress constraints on the optimum blade designs are assessed. The results indicate that there is an increase in blade weight and a significant change in the design variable distributions with an increase in the number of frequency constraints. The inclusion of stress constraints has different effects on the wall thickness distributions of rectangular and tapered blades, but tends to increase the magnitude of the nonstructural segment weight distributions for both blade types.

Description: The onset of instabilities in a fluid contained in a rotating hemispherical shell, driven by thermal gradients imposed upon the hemispherical boundaries and by a spherically symmetric radial body force, is numerically studied. Computations are presented for a range of Taylor and thermal Rossby numbers. The analysis indicates the presence of an instability dependent upon the spherically radial gravity alone when the warmest temperatures are at the pole and an additional centrifugal buoyant instability for weak imposed gravity and fast rotation when the temperature decreases poleward.

Description: The transabsorptivity concept which specifies the heat input into the PBL resulting from surface-atmosphere interactions is discussed. This concept is examined in terms of governing equations, and transabsorptivity is defined as the product of the surface absorptivity and the transfer efficiency. It is proposed that the climatic effects of surface changes be formulated in terms of changes in the transabsorptivity. A diagram of the surface-atmosphere interactions is provided.

Description: Current research in the field of advanced adaptive structures for space applications is reviewed. A classification of adaptive structures is proposed whereby such structures are subdivided into adaptive, sensory, controlled, active, and intelligent structures. The definition and properties of each type of adaptive structures are presented, and methods of structure control are discussed.

Description: The simultaneous active control of flexural and extensional vibrations in elastic beams is experimentally investigated. The results demonstrate that using pairs of piezoceramic transducers, whose elements are symmetrically located and independently controlled by a multichannel adaptive controller, enables the high attenuation of both flexural and extensional response. This capability is due to the nature of the piezoceramic element, which when bonded to the surface of the structure and electrically excited, exerts a surface strain on the structure. This strain enables input of both shear forces and moments into the structural system. The results are applicable to many situations where extensional vibrations couple to large flexural vibrations and subsequently radiate significant sound levels.

Description: Consideration is given to the determination of the optimal bands for measuring and deriving the total outgoing longwave radiation (OLR), surface downward flux (SDF), and cooling rates (CRs) using linear regression. The optimal bands are determined from scatter plots of total fluxes and cooling rates associated with the various bands. It is found that the best band for OLR is between 800 and 1200/cm, while the best band for SDF is between 500 and 660/cm or between 660 and 800/cm. For CRs, it is shown that the best band is also between 660 and 800/cm. It is noted that the AVHRR OLR is damped compared with the Nimbus-7 earth radiation budget (ERB) OLR derived from the broadband, narrow FOV ERB instrument.

Description: Ozone measurements made by the SME UV Spectrometer and the Stratosphere Aerosol and Gas Experiment II (SAGE II) spectometer are compared at 1.0 mbar for the time period from October 1984 to December 1986, using a model of the diurnal variation of ozone to correct for the difference in local times of the two measurements. The absolute values of the ozone mixing ratio measured by the two spectrometers were found to agree to better than 5 percent, with no significant divergence between the instruments. It is concluded that, since the SAGE II data are not dependent on the absolute calibration of the instrument, these data can be used as time-dependent 'ground truth' measurements for comparisons with other instruments.

Description: The literature on the mathematical modeling of large space structures is first reviewed, with attention given to continuum models, model order reduction, substructuring, and computational techniques. System identification and mode verification are then discussed with reference to the verification of mathematical models of large space structures. In connection with analysis, the paper surveys recent research on eigensolvers and dynamic response solvers for large-order finite-element-based models.

Description: The spectral data obtained by the infrared interferometer Spectrometer (IRIS) flown on Nimbus 4 satellite in 1970 indicated the existence of optically thin ice clouds in the upper troposphere that probably extended into lower stratosphere, in the polar regions, during winter and early spring. The spectral features of these clouds differ somewhat from that of the optically thin cirrus clouds in the tropics. From theoretical simulation of the infrared spectra in the 8-25 micron region, it is inferred that these polar clouds have a vertical stratification in particle size, with larger particles (about 12 microns) in the bottom of the cloud and smaller ones (less than 1 micron) aloft. Radiative transfer calculations also suggest that the equivalent ice-water content of these polar clouds is of the order of 1 mg/sq cm.

Description: A description is presented of cirrus based on results from a FIRE observation flight in central Wisconsin on October 28, 1986. Cirrus structure and radiative parameters as determined by the ER-2 lidar and imaging spectral radiometers are presented. From the lidar observations a complex structure was shown with differing cloud layers extending over six kilometers of altitude range. Both thin and dense cirrus layers were present and mixed phase clouds were found at lower altitudes. As indicated by the cloud structure, precipitation of crystals from high, but vertically thin, layers produces a significant fraction of the lower cirrus. Multiple layers should be considered as normal for cirrus formations. It is noted that the cloud height is an important factor for satellite cloud retrievals and cloud climatology.

Description: This paper discusses the research in adaptive structures conducted at NASA Langley Research Center. The objective in the research program on adaptive truss structures is to develop an integrated approach for the design, test, and evaluation of adaptive trusses. An adaptive structure must include sensors for measuring some of the states of the mechanism, a controller that processes the sensor information and generates command signals, and a device that will cause the struts in the mechanism to change length. Based on the results of the research program, it is concluded that alternative designs for future space applications are offered, and adaptive truss has been demonstrated to be effective for vibration suppression.

Description: Rains at the onset of the October-April rainy season in southern Israel have steeply increased in the last 25 years relative to the previous 20 years, and are accompanied by an appreciable general increase of rainy-season rainfall. This increase in precipitation is specifically attributable to an intensification of the convection and advection processes due to afforestation and increased cultivation-induced enhancement of the daytime sensible heat flux from the generally dry surface; the enhancement proceeds from both the reduced surface albedo and the reduced soil heat flux in October, when insolation is strong. Greater daytime convection can lead to penetration of inversions capping the planetary boundary layer, while strengthened advection can furnish moist air from the Mediterranean.

Description: The mobility power flow (MPF) approach is used in this paper to describe the flexural behavior of an L-shaped plate structure consisting of thick plates with rotary inertia and shear deformation effects included in the analysis. The introduction of the thick plate effects significantly increases the complexity of the structural mobility functions used in the definitions of the power flow terms; however, because of the substructuring that is used in the MPF approach, the complexity of the problem is significantly reduced as compared to solving for the global structure. Additionally, with the MPF approach the modal behavior is described. The MPF analysis of the L-shaped plate is performed for the case of point force excitation on one plate, with the two plates being identical in both size and thickness. The results of this analysis are compared to results from the finite-element analysis (FEA) and the statistical energy analysis (SEA) and show very good agreement in the low- and high-frequency regimes, respectively.

Description: A method is presented for tailoring plate and shell composite structures for optimal forced damped dynamic response. The damping of specific vibration modes is optimized with respect to dynamic performance criteria including placement of natural frequencies and minimization of resonance amplitudes. The structural composite damping is synthesized from the properties of the constituent materials, laminate parameters, and structural geometry based on a specialty finite element. Application studies include the optimization of laminated composite beams and composite shells with fiber volume ratios and ply angles as design variables. The results illustrate the significance of damping tailoring to the dynamic performance of composite structures, and the effectiveness of the method in optimizing the structural dynamic response.

Description: Analytical and experimental techniques for the prediction and ground verification of the damped structural dynamics of space structures are developed. The options available for similarity-scaled model testing, including replica and multiple scale approaches, are reviewed. For the case when the distortion of potentially dissipative or nonlinear joints, which would be required in multiple-scale modeling, is impractical, a new type of modeling is introduced, which uses a hybrid of joints at replica scale and connecting elements at a modified multiple scale. The model design requirements for replica, multiple-scale, and hybrid models are developed, and the expected scaling of nonlinear dissipation in joints is derived. A damping prediction scheme is developed that relies on a finite element model of the undamped structure and measurements of the individual joint properties to predict the modal damping of the truss attributable to the joints. A hybrid-scaled model of a segment of the Space Station was built and dynamically tested. The predicted and measured truss damping compared favorably.

Description: The most widely used version of the Nimbus-7 middle atmosphere dataset is the set of high quality, daily, and zonal Fourier coefficients that resolve information out to six wavenumbers at 12 UTC. A Kalman filter algorithm was applied to the original profile data in order to generate those fields for the data archive or LAMAT product. The characteristics and implementation of the algorithm are described in some detail, along with examples of the output for each of the LIMS parameters.

Description: Results are presented of the equatorial wave campaign-II, a meteorological rocket study which was part of the Indian Middle Atmosphere Program. The equatorial wave campaign-II was conducted from Shar, India (13.7 deg N, 80.2 deg E) from January 15-February 28, 1986. By means of high altitude balloon and the RH-200 meteorological rocket, winds were measured from ground level up to 60 km altitude once each day during the 45-day period. The oscillation frequencies of the deviations in the east-west component of the winds from their mean at each 1-km height interval are obtained by the maximum entropy method. The phases and amplitudes of these frequencies are determined by use of the least squares method on the wind variation time series. Enhanced wave activity is shown to take place in the troposphere and lower mesosphere. The tropospheric waves observed suggest themselves to be Rossby waves of extratropical origin penetrating to tropical latitudes. The observed stratospheric/mesospheric waves appear to emanate from a source around the stratopause.

Description: Elastic-plastic behavior of fibrous composite laminates is analyzed for coupled in-plane mechanical loads and uniform thermal changes. Constitutive equations of the individual fibrous layers are derived from a vanishing fiber diameter model that represents the essential axial constraint between the phases. This permits derivation of closed form equations for the overall yield condition, stress concentration factors, and instantaneous compliance. Thermoelastic properties of the phases and yield stress of the matrix phase are functions of temperature. The effect of the model assumptions on the predicted behavior of composite laminates is examined by comparing the calculated response under cyclic thermal changes to available theoretical results and experimental measurements.

Description: An elasticity solution has been used to analyze matrix stresses near the fiber/matrix interface in continuous fiber-reinforced metal-matrix composites, modeling the micromechanics in question in terms of a cylindrical fiber and cylindrical matrix sheath which is embedded in an orthotropic medium representing the composite. The model's predictions for lamina thermal and mechanical properties are applied to a laminate analysis determining ply-level stresses due to thermomechanical loading. A comparison is made between these results, which assume cylindrical symmetry, and the predictions yielded by a FEM model in which the fibers are arranged in a square array.

Description: A Charney-Branscome based parameterization has been tested as a way of representing the eddy sensible heat transports missing in a zonally averaged dynamic model (ZADM) of the atmosphere. The ZADM used is a zonally averaged version of a general circulation model (GCM). The parameterized transports in the ZADM are gaged against the corresponding fluxes explicitly simulated in the GCM, using the same zonally averaged boundary conditions in both models. The Charney-Branscome approach neglects stationary eddies and transient barotropic disturbances and relies on a set of simplifying assumptions, including the linear appoximation, to describe growing transient baroclinic eddies. Nevertheless, fairly satisfactory results are obtained when the parameterization is performed interactively with the model. Compared with noninteractive tests, a very efficient restoring feedback effect between the modeled zonal-mean climate and the parameterized meridional eddy transport is identified.

Description: A dual-control test system measuring the strength of graphite/epoxy specimens under tension and compression for a wide range of bearing-bypass load ratios is presented. The bearing-bypass strengths of single-fastener specimens are measured for damage onset and ultimate failure and are plotted against one another. The results indicate that an initiated damage grows to failure in the same mode for most cases. However, if the damage is initiated in the compression-reacted-bearing mode, the specimens fail in the offset-compression mode. It is concluded that this type of transition can occur in multi-fastener joints under compression and complicate the strength predictions.

Description: Acoustic emission in 51-cm diameter graphite/epoxy pressure vessels was monitored during pressurization (hydrotesting). Several vessels were subjected to impact by a blunt impactor, but only after the vessels had been proofed; that is, pressurized to 80 percent of nominal burst pressure as determined from control (unimpacted) vessels. AE activity was then monitored throughout a series of successively higher pressure cycles ranging from 10 to 60 percent of ultimate. Each cycle included a ramp up to pressure followed by a 4-min hold period and then pressure unload. The event rate was high, and especially modified AE analyzers had to be used to acquire the data. This paper presents the AE event count versus pressure history of these tests and demonstrates the ability of the AE technique to monitor the growth of damage and to estimate the effect on ultimate strength. The number of events that occurred during pressure holds proved to be a reasonable estimator of vessel performance.

Description: The characteristic features, the diurnal cycle, and the spatial distribution of deep convection over the equatorial Pacific and the relationship of deep convection to SST and surface-wind convergence were examined using a combined visible-IR (VS-IR) threshold method and an IR-only threshold method for diagnosing deep convection clouds (DCCs). Results suggest that deep convection is latitudinally confined to a much smaller spatial scale than that suggested by maps of outgoing long-wave radiation. The results suggested that there are two types of relationships between deep convection, SST, and surface-wind convergence: the west Pacific type and the east Pacific type. The latter relationship is observed in the east Pacific only when SST is not abnormally warm.

Description: This paper describes a method for determining global atmospheric-temperature anomalies by means of satellite microwave radiometry. It is shown that microwave measurements of molecular oxygen thermal emission by the Microwave Sounding Units (MSUs) flying aboard the NOAA-6 and NOAA-7 can be used to monitor tropospheric temperature anomalies on global basis to a high level of precision. Comparisons between monthly MSU-derived hemispheric temperature anomalies with those computed from surface thermometer data show a very good agreement over the United States, although not for the hemispheres, especially the Southern Hemisphere. In this latter case, the poor agreement is ascribed to weaker thermal coupling between the ocean and the deep troposphere than that over the U.S. Annual anomalies for the hemispheres exhibit better correlations than do monthly anomalies.

Description: As part of a calibration/validation effort for the special sensor microwave/imager (SSM/I), coincident observations of SSM/I brightness temperatures and surface-based observations of cloud liquid water were obtained. These observations were used to validate initial algorithms and to derive an improved algorithm. The initial algorithms were divided into latitudinal-, seasonal-, and surface-type zones. It was found that these initial algorithms, which were of the D-matrix type, did not yield sufficiently accurate results. The surface-based measurements of channels were investigated; however, the 85V channel was excluded because of excessive noise. It was found that there is no significant correlation between the SSM/I brightness temperatures and the surface-based cloud liquid water determination when the background surface is land or snow. A high correlation was found between brightness temperatures and ground-based measurements over the ocean.

Description: The impact of clouds on the earth's radiation balance is assessed in terms of longwave, shortwave, and net cloud forcing by using monthly averaged clear-sky and cloudy-sky flux data derived from the NASA Earth Radiation Budget Experiment (ERBE). Emphasis is placed on regional measurements, regional cloud forcing, zonal cloud forcing, and snow and ice contributions. It is shown that the global mean cooling varied from 14 to 21 W/sq m between April 1985 and January 1986; hemispherically, the longwave and shortwave cloud forcing nearly cancel each other in the winter hemisphere, while in the summer the negative shortwave cloud forcing is significantly lower than the longwave cloud forcing, producing a strong cooling. The ERBE data reveal that globally, hemispherically, and zonally, clouds have a significant effect on the radiative heating gradients.

Description: In situ airborne measurements of turbulent heat, moisture, momentum, ozone, and carbon monoxide fluxes in a convective boundary layer were obtained over a tropical rain forest between 1100 and 1630 LT on May 4, 1987. The aircraft flight path was chosen so as to fly over the tower site at the Ducke Forest Reserve near Manaus, Amazonas, Brazil. Both turbulence statistics and mean quantities were used to study the budgets of heat, water vapor, ozone, and carbon monoxide. The ozone budget study shows an accumulation rate in the boundary layer of 0.3 + or - 0.2 ppbv/h. The surface resistance to ozone during this flight was determined to be 0.06 + or - 0.03 s/cm, while the aerodynamic resistance was 0.14-0.17 s/cm. Results from the CO budget analysis show a midday accumulation rate of 0.6 + or - 0.3 ppbv/h in the Amazonian boundary layer. The evidence suggests production of CO in the PBL. A source of CO may exist below the lowest flight level (about 150 m), although it was not possible to determine what part of the flux at flight level was due to chemical production and what part may be due to surface emission.

Description: The issue of the interaction of the monsoon large-scale circulation and intraseasonal oscillations is addressed, showing that, as a result of the interaction of the large scale monsoon flow with the near-equatorial intraseasonal oscillation, unstable baroclinic disturbances are generated over the monsoon region. From a linear stability analysis of quasi-geostrophic motion in a two-level model, it is shown that the westward propagating disturbances generated over the monsoon region are the manifestation of heat-induced unstable Rossby waves. The instability is favored in the region with large vertical wind shear and reduced effective static stability. The monsoon large scale circulation over India and southeast Asia and the plentiful supply of moisture in the region appear to be favorable for the development of these unstable waves.

Description: An overview of meteorological conditions during the NASA Global Tropospheric Experiment/Chemical Instrumentation Testing and Evaluation (GTE/CITE 2) summer 1986 flight series is presented. Computer-generated isentropic trajectories are used to trace the history of air masses encountered along each aircraft flight path. The synoptic-scale wind fields are depicted based on Montgomery stream function analyses. Time series of aircraft-measured temperature, dew point, ozone, and altitude are shown to depict air mass variability. Observed differences between maritime tropical and maritime polar air masses are discussed.

Description: The possibility that the greenhouse warming predicted by the GISS general-circulation model and other GCMs could lead to severe droughts is investigated by means of numerical simulations, with a focus on the role of potential evapotranspiration E(P). The relationships between precipitation (P), E(P), soil moisture, and vegetation changes in GCMs are discussed; the empirically derived Palmer drought-intensity index and a new supply-demand index (SDDI) based on changes in P - E(P) are described; and simulation results for the period 1960-2060 are presented in extensive tables, graphs, and computer-generated color maps. Simulations with both drought indices predict increasing drought frequency for the U.S., with effects already apparent in the 1990s and a 50-percent frequency of severe droughts by the 2050s. Analyses of arid periods during the Mesozoic and Cenozoic are shown to support the use of the SDDI in GCM drought prediction.

Description: In this June 29, 1986 case study, a radiative transfer model is used to simulate the aircraft multichannel microwave brightness temperatures presented in the Adler et al. (1990) paper and to study the convective storm structure. Ground-based radar data are used to derive hydrometeor profiles of the storm, based on which the microwave upwelling brightness temperatures are calculated. Various vertical hydrometeor phase profiles and the Marshall and Palmer (M-P, 1948) and Sekhon and Srivastava (S-S, 1970) ice particle size distributions are experimented in the model. The results are compared with the aircraft radiometric data. The comparison reveals that the M-P distribution well represents the ice particle size distribution, especially in the upper tropospheric portion of the cloud; the S-S distribution appears to better simulate the ice particle size at the lower portion of the cloud, which has a greater effect on the low-frequency microwave upwelling brightness temperatures; and that, in deep convective regions, significant supercooled liquid water (about 0.5 g/cu m) may be present up to the -30 C layer, while in less convective areas, frozen hydrometeors are predominant above -10 C level.

Description: The residual mean circulation (RMC) formulation of zonally averaged transport in the middle atmosphere produces a circulation which depends on the distributions of net diabatic heating and temperature. Such circulations are from two temperature data sets, using the same radiative transfer code (Rosenfield et al. 1987). These circulations are then used to transport N2O in a photochemical model. The circulations and the resulting N2O distributions are notably different during the Northern Hemisphere winter, with that based on the NMC temperatures producing too much upward transport in the tropical stratosphere, as judged by comparison with the stratospheric and mesoscale sounder data. The experiment demonstrates that model calculations, in general, and perturbation assessments, in particular, are likely to be quite sensitive to the choice of input temperature data (where this is not computed self-consistently). It also reveals what appears to be a seasonally dependent bias in NMC zonally averaged temperatures with respect to those obtained from the LIMS instrument during 1978/1979.

Description: A model was developed for simulating he manufacturing process of filament-wound cylinders made of a thermoset matrix composite. The model relates the process variables (winding speed, fiber tension, applied temperature) to the parameters characterizing the composite cylinder and the mandrel. The model is applicable to cylinders for which the diameter is large compared to the wall thickness. The model was implemented by a user-friendly computer code suitable for generating numerical results.

Description: Experimental evidence shows that the area-average rain rate and the fractional area covered by rain rate exceeding a fixed threshold are highly correlated; that is, are highly linearly related. A precise theoretical explanation of this fact is given. The explanation is based on the observation that rain rate has a mixed distribution, one that is a mixture of a discrete distribution and a continuous distribution. Under a homogeneity assumption, the slope of the linear relationship depends only on the continuous part of the distribution and as such is found to be markedly immune to parameter changes. This is illustrated by certain slope surfaces obtained from three specific distributions. The threshold level can be chosen in an optimal way by minimizing a certain distance function defined over the threshold range. In general, the threshold level should be not too far from the mean rain rate conditional on rain. The so-called threshold method advocates measuring rainfall from fractional area exploiting the observed linear relationship of the later with the area average rain rate. The method is potentially useful for the estimation of rainfall from space via satellites.

Description: The effect of doubling the atmospheric content of CO2 on the middle-atmosphere climate is investigated using the GISS global climate model. In the standard experiment, the CO2 concentration is doubled both in the stratosphere and troposphere, and the SSTs are increased to match those of the doubled CO2 run of the GISS model. Results show that the doubling of CO2 leads to higher temperatures in the troposphere, and lower temperatures in the stratosphere, with a net result being a decrease of static stability for the atmosphere as a whole. The middle atmosphere dynamical differences found were on the order of 10-20 percent of the model values for the current climate. These differences, along with the calculated temperature differences of up to about 10 C, may have a significant impact on the chemistry of the future atmosphere, including that of stratospheric ozone, the polar ozone 'hole', and basic atmospheric composition.

Description: A disordered structure with weakly coupled subsystems has localized modes with the vibratory energy concentrated in one part of the mode shape. The localization of modes may significantly affect the forced vibration response, increasing the maximum vibration amplitude dramatically in some cases. It is the scope of this paper to study the forced vibration of nearly periodic systems consisting of almost identical substructures and to analyze their free and forced dynamic responses probabilistically. It is shown that the sensitivity of the forced response to the degree of localization depends on a combination of the symmetry of the mode, which is excited, and the phase difference between the forces acting on each substructure. These results might explain the range of contrasting conclusions of earlier publications on the effects of forced response on mistuned structures. A probabilistic analysis of the free and forced responses of a nearly periodic structure is shown to be useful in the design of structures that are sensitive to the degree of localization. The results of the probabilistic analysis are verified using Monte Carlo simulation.

Description: An effort is made to determine relationships between reflectivity (Z) and rain rate (R) which are tuned to the local climatology. The development of such relations was motivated by the need to understand the role of precipitation in controlling general circulation and in affecting such phenomena as ENSO. Attention is given to methods of deriving such relations and how they are linked to area integral rainfall measurements. In essence, the relation is tuned so that the probability distribution of reflectivity, P(Z), replicates that of R over some predetermined space-time climatic domain. Thus, the accurate measurement of the average R over any smaller domain depends on how closely the sampled P(Z) approximates the climatic P(Z). The probability matching method used is a modification of the approach of Calheiros and Zawadzki (1987) and Rosenfeld (1980). The technique is applied to data from Germany and the eastern tropical Atlantic (GATE).

Description: Simplified procedures are described to design and analyze single and multi-bolt composite joints. Numerical examples illustrate the use of these methods. Factors affecting composite bolted joints are summarized. References are cited where more detailed discussion is presented on specific aspects of composite bolted joints. Design variables associated with these joints are summarized in the appendix.

Description: The paper presents both the Roach equation for the rate of energy dissipation due to clear air turbulence and Richardson number tendencies in isentropic coordinates and examines the implications of these formulations to determine whether there is a dynamic interdependence between Ri and the nonturbulent deformation processes. The equation representing the ln(Ri) tendency is applied diagnostically to grids from an isentropic analysis of archived soundings. The evolution of the Richardson number fields over 12-hour time periods is examined using a mechanistic model. It is suggested that the application of the Roach equation for the turbulent dissipation rate should have a more restricted use. Analyses of the meso-alpha scale Richardson number and of the Richardson number tendency fields reveal a phase relationship consistent with the theoretical predictions.

Description: An algorithm for three-dimensional thermoviscoplasticity with inertial effects is presented. The algorithm utilizes a unified thermoviscoplastic constitutive model with directional hardening (Bodner-Partom). An example problem is shown in which thermally induced vibrations lead to material yielding at elevated temperatures. Significant dampening caused by inelastic strain is shown to take place in the structure.

Description: A technique that uses the spatial variance of image brightness temperature to derive total column precipitable water is applied to high-resolution multispectral aircraft scanner data for the June 19, 1986 COHMEX day. The technique has several advantages over other approaches in that it requires only relative calibration accuracy, is less susceptible to instrument error, and does not directly use a priori information. Results indicate significant horizontal variability of precipitable water at the mesoscale. Precipitable water gradients of 6 mm per 10 km are not uncommon. The results verify well against special rawinsonde measurements and the ensuing cloud field development. While only applied to this specialized aircraft data, the applicability of the technique to operational AVHRR and VAS data is discussed.

Description: A potential vorticity theorem and its two summary statements published by Haynes and McIntyre are challenged conceptually by equations, discussions and examples. The apparent simplification proposed by the authors to convert from a mass to volume integral, i.e., by cancelling density against the specific volume in the potential vorticity, changes the physical significance of the integrand. It no longer is the potential vorticity. The resulting mean for either a bulk Eulerian or Lagrangian system is then not analogous to a mixing ratio and therefore not independent of the broad spectrum of internal waves, the independence that makes Ertel's potential vorticity so valuable either as a stratospheric tracer or as a predictive or diagnostic, large scale, meteorological variable.

Description: During the second Amazon Boundary Layer Experiment (ABLE 2B), meteorological observations, chemical measurements, and model simulations are utilized in order to interpret convective cloud draft structure and to analyze its role in transport and vertical distribution of trace gases. One-dimensional photochemical model results suggest that the observed poststorm changes in ozone concentration can be attributed to convective transports rather than photochemical production and the results of a two-dimensional time-dependent cloud model simulation are presented for the May 6, 1987 squall system. The mesoscale convective system exhibited evidence of significant midlevel detrainment in addition to transports to anvil heights. Chemical measurements of O3 and CO obtained in the convective environment are used to predict photochemical production within the troposphere and to corroborate the cloud model results.

Description: The temporal variation in the concentration and chemistry of the atmospheric aerosol over central Amazonia, Brazil, during the 1987 wet season is discussed based on ground and aircraft collected data obtained during the NASA GTE ABLE 2B expedition conducted in April/May 1987. It is found that wet-season aerosol concentrations and composition are variable in contrast to the more uniform biogenic aerosol observed during the 1985 dry season; four distinct intervals of enhanced aerosol concentration coincided with short periods (3 to 5 d) of extensive rainfall. It is hypothesized that aerosol chemistry in Amazonia during the wet season is strongly influenced by long-range transport of soil dust, marine aerosol, and possibly biomass combustion products advected into the central Basin by large-scale tropospheric circulation, producing periodic pulses of material input to local boundary layer air. The resultant wet-season aerosol regime is dynamic, in contrast to the uniformity of natural biogenic aerosols during the dry season.

Description: The question of load biaxiality strongly affecting almost all of the characteristics of brittle fracture behavior of a cracked body is investigated. Results of research published piecemeal over the years by the authors have shown that the stress and displacement fields, the elastic strain energy density, and the maximum shear stress near the crack tip are all altered by loads applied parallel to the crack, as are the angle of initial crack extension, the strain energy of the entire body, the fracture load, and the rate of fatigue crack growth. A synthesis and summary of this research is presented showing the shortcomings inherent in both Griffith's global energy rate theory for crack instability and Irwin's local crack-tip stress intensity theory for fracture toughness. In both theories only the tensile load perpendicular to the crack influences fracture behavior of the body.

Description: The latent heat represented by atmospheric water vapor is extremely important to the energetics of the earth system. Future satellites (NOAA and DMSP) will carry microwave radiometers designed to measure the profile of water vapor globally. The problem of retrieving water vapor from the measurements is highly nonlinear even in clear atmospheres and the addition of clouds only makes it more so. In this paper, an algorithm with several novel features, which will retrieve water vapor profiles from microwave radiometric measurements even in the presence of clouds, is developed. Simulations with this algorithm show a vertical resolution on the order of 3 km and that clouds are well handled in many, but not all, circumstances. The most surprising result is that clouds can actually improve the vertical resolution of the retrieval.

Description: Aspects of highly organized forms of deep convection at midlatitudes are reviewed. Past emphasis in field work and cloud modeling has been directed toward severe weather as evidenced by research on tornadoes, hail, and strong surface winds. A number of specific issues concerning future thrusts, tactics, and techniques in convective dynamics are presented. These subjects include; convective modes and parameterization, global structure and scale interaction, convective energetics, transport studies, anvils and scale interaction, and scale selection. Also discussed are analysis workshops, four-dimensional data assimilation, matching models with observations, network Doppler analyses, mesoscale variability, and high-resolution/high-performance Doppler. It is also noted, that, classical surface measurements and soundings, flight-level research aircraft data, passive satellite data, and traditional photogrammetric studies are examples of datasets that require assimilation and integration.

Description: A statistical retrieval technique is developed to derive the atmospheric water vapor column content from the Special Sensor Microwave/Imager (SSM/I) measurements. The radiometer signals are simulated by means of radiative-transfer calculations for a large set of atmospheric/oceanic situations. These simulated responses are subsequently summarized by multivariate analyses, giving water-vapor coefficients and error estimates. Radiative-transfer calculations show that the SSM/I microwave imager can detect atmospheric water vapor structures with an accuracy from 0.145 to 0.17 g/sq cm. The accuracy of the method is confirmed by globally distributed match-ups with radiosonde measurements.

Description: The natural vibration frequencies of orthotropic and anisotropic, simply supported right circular cylinders are predicted using a theory which takes into account higher-order transverse shear deformation effects. A comparison between results based on first-order transverse shear deformation theory and the higher-order theory indicates that an additional allowance for transverse shear deformation has a negligible effect on the predicted natural vibration frequencies associated with long wavelengths, but significantly reduces the natural vibration frequencies associated with short wavelengths. Results of a parametric study of ply orientation for two classes of laminates indicates that while stacking sequence affects natural vibration frequencies, cylinder geometry and mode shape are more important in accurately predicting transverse shear deformation effects. Transverse shearing effects are less important in predicting natural vibration frequencies associated with long wavelength than in predicting axial compressive buckling loads.

Description: Episodes of westerly wind are an important aspect of surface stress variability in the western Pacific. During ENSO periods, the presence of such wind episodes comprises much of the LF relaxation of the trades over the central and western Pacific. This paper describes the oceanic Kelvin pulse response to a single idealized episode of westerly wind stress, using results from linear theory as well as from a 27-level general circulation model. When stratification typical of the western and eastern Pacific is used, the conservation of energy flux predicts a reduction of surface currents associated with the first baroclinic mode and an enhancement of surface currents associated with the second baroclinic mode. The idealized wind anomaly is also used to drive an ocean general circulation model. When the wind anomaly is weak, the model Kelvin response agrees with predictions of linear theory. For more realistic strong forcing there are three important deviations from linear theory: the amplitude of low baroclinic modes increases; the amplitude of higher baroclinic modes decreases; and the phase speed increases.