ALBERT

Description: Chemical and cellular parameters were measured in human subjects before and after exposure to a decompression schedule involving 8 h of oxygen prebreathing. The exposure was designed to simulate space-flight extravehicular activity (EVA) for 6 h. Several statistically significant changes in blood parameters were observed following the exposure: increases in calcium, magnesium, osmolality, low-density lipoprotein cholesterol, monocytes, and prothrombin time, and decreases in chloride, creatine phosphokinase and eosinophils. The changes, however, were small in magnitude and blood factor levels remained within normal clinical ranges. Thus, the decompression profile used in this study is not likely to result in blood changes that would pose a threat to astronauts during EVA.

Description: No abstract available

Description: No abstract available

Description: Non-immune SJL (H-2s) spleen cells were fused with non-secreting, non-antigen presenting (H-2d) Balb/c 653-myeloma cells and the hybridomas were cloned by two limiting dilutions. The resulting hybrid B-cell clones were tested for their antigen presentation capability to SJL T-cell lines that were specific for either lysozyme or myoglobin. In proliferative assays, 53% of the antigen presenting B-cell clones presented both myoglobin and lysozyme (general presenters) while the other 47% presented specifically either myoglobin or lysozyme (specific presenters). The ability to selectively present either myoglobin or lysozyme indicates that antigen presentation at the clonal level can be specific or non-specific depending on the particular B-cell clone.

Description: Recently, we reported the preparation and antigen-presenting properties of hybridoma B-cell clones obtained after fusing non-secreting, non-antigen presenting Balb/c 653-myeloma cells with non-immune SJL spleen cells. It was found that antigen presentation at the clonal level can be specific or non-specific, depending on the particular B-cell clone. In the present work, one specific and one general presenter B-cell clones were tested for their epitope presentation ability to SJL T-cells that were specific to lysozyme or myoglobin. B-cell clone A1G12, a general presenter which presented both lysozyme and myoglobin to their respective T-cell lines, was found to present all five myoglobin epitopes while clone A1L16, a lysozyme specific presenter presented only one of the three epitopes of lysozyme. The latter reveals a hitherto unknown submolecular specificity (to a given epitope within a protein) for antigen presenting cells at the clonal level. Therefore, the specificity of T-cell recognition does not only derive from the T-cell but may also be dependent on the epitope specificity of the antigen-presenting B-cell.

Description: The morphological and physiological effects of 4 weeks of high-frequency electrical stimulation (1 h/day, 5 days/week) on cast-immobilized rabbit hindlimbs were investigated in the tibialis anterior muscle and peroneal nerve. In 2 out of 6 animals, high-frequency stimulation with immobilization caused muscle fiber death, internalization of muscle fiber nuclei, connective tissue proliferation, inflammatory response, altered fiber size distribution and variable staining intensities. The fast-twitch fibers were predominantly affected. Two of six peripheral nerves subjected to immobilization and stimulation showed severe damage. Tetanic forces were significantly reduced in the affected muscles. Therefore, the immobilization and high-frequency stimulation may be detrimental to myoneural structure and function and, thus, this combination of therapies should be applied conservatively.

Description: Several recent studies have shown performance decrements with increasing display size when background texture elements are present in a same-different feature discrimination task--a result that challenges the traditional notion that the identities of simple visual features are processed in parallel, preattentively. Four experiments are reported that explore the implications of these results. Experiment 1 replicates the recent studies but limits the generalizability of the results to small target numbers. Experiments 2 and 3 show that the observed performance decrements are not due to a serial or even limited-capacity, parallel process. Experiment 4 suggests that decision factors idiosyncratic to the use of texture elements in a same-different task are responsible for the effect. It is concluded that the identification of simple visual features proceeds in parallel, with unlimited capacity (i.e., preattentively).

Description: Future space missions of long duration may require that autologous leukocytes be stored in flight for infusion to restore normal immune competence in crewmembers. Peripheral blood mononuclear cells (PBMNCs), as leukocyte concentrates in autologous plasma and 2% dextrose, were stored in the microgravity conditions provided by the U.S. Space Shuttle Columbia (Mission 61-C). Activity of PBMNC after space flight was compared with that from a series of preflight ground control experiments, which demonstrated in culture a progressive daily loss in mitogen-stimulated protein synthesis at 24 h and thymidine uptake at 72 h after storage for 7 d at 4 degrees C. Post-storage viabilities were at least 90% as determined by trypan dye exclusion. A progressive reduction in the percentage of PBMNC expressing cell-surface phenotype markers, which was similar for monocytes, B cells, and T-cell subsets, also occurred after storage. The ability of PBMNC, stored for 8 d in Columbia's middeck, to become activated and proliferate in vitro was similar to that of cells that remained in identical flight lockers on the ground as 1-G controls, thus indicating that PBMNCs were not adversely affected by storage under microgravity conditions.

Description: We present a technique for introducing broad-band respiratory perturbations so that the response characteristics of the autonomic nervous system can be determined noninvasively over a wide range of physiologically relevant frequencies. A subject's respiratory bandwidth was broadened by breathing on cue to a sequence of audible tones spaced by Poisson intervals. The transfer function between the respiratory input and the resulting instantaneous heart rate was then computed using spectral analysis techniques. Results using this method are comparable to those found using traditional techniques, but are obtained with an economy of data collection.

Description: Each of 12 subjects set a binocularly viewed target to apparent eye level; the target was projected on the rear wall of an open box, the floor of which was horizontal or pitched up and down at angles of 7.5 degrees and 15 degrees. Settings of the target were systematically biased by 60% of the pitch angle when the interior of the box was illuminated, but by only 5% when the interior of the box was darkened. Within-subjects variability of the settings was less under illuminated viewing conditions than in the dark, but was independent of box pitch angle. In a second experiment, 11 subjects were tested with an illuminated pitched box, yielding biases of 53% and 49% for binocular and monocular viewing conditions, respectively. The results are discussed in terms of individual and interactive effects of optical, gravitational, and extraretinal eye-position information in determining judgements of eye level.

Description: A physical map for the chromosome of the thermophilic archaebacterium Thermococcus celer Vu13 has been constructed. Thirty-four restriction endonucleases were tested for their ability to generate large restriction fragments from the chromosome of T. celer. Of these, the enzymes NheI, SpeI, and XbaI yielded the fewest fragments when analyzed by pulsed-field electrophoresis. NheI and SpeI each gave 5 fragments, while XbaI gave 12. The size of the T. celer chromosome was determined from the sum of the apparent sizes of restriction fragments derived from single and double digests by using these enzymes and was found to be 1,890 +/- 27 kilobase pairs. Partial and complete digests allowed the order of all but three small (less than 15 kilobase pairs) fragments to be deduced. These three fragments were assigned positions by using hybridization probes derived from these restriction fragments. The positions of the other fragments were confirmed by using hybridization probes derived in the same manner. The positions of the 5S, 16S, and 23S rRNA genes as well as the 7S RNA gene were located on this map by using cloned portions of these genes as hybridization probes. The 5S rRNA gene was localized 48 to 196 kilobases from the 5' end of the 16S gene. The 7S RNA gene was localized 190 to 504 kilobases from the 3' end of the 23S gene. These analyses demonstrated that the chromosome of T. celer is a single, circular DNA molecule. This is the first such demonstration of the structure of an archaebacterial chromosome.

Description: Tobacco (Nicotiana tabacum L., cv. 'Coker 319') plants were grown for 28 days in flowing nutrient culture containing either 1.0 mM NO3- or 1.0 mM NH4+ as the nitrogen source in a complete nutrient solution. Acidities of the solutions were controlled at pH 6.0 or 4.0 for each nitrogen source. Plants were sampled at intervals of 6 to 8 days for determination of dry matter and nitrogen accumulation. Specific rates of NO3- or NH4+ uptake (rate of uptake per unit root mass) were calculated from these data. Net photosynthetic rates per unit leaf area were measured on attached leaves by infrared gas analysis. When NO3- [correction of NO-] was the sole nitrogen source, root growth and nitrogen uptake rate were unaffected by pH of the solution, and photosynthetic activity of leaves and accumulation of dry matter and nitrogen in the whole plant were similar. When NH4+ was the nitrogen source, photosynthetic rate of leaves and accumulation of dry matter and nitrogen in the whole plant were not statistically different from NO3(-) -fed plants when acidity of the solution was controlled at pH 6.0. When acidity for NH4(+) -fed plants was increased to pH 4.0, however, specific rate of NH4+ uptake decreased by about 50% within the first 6 days of treatment. The effect of acidity on root function was associated with a decreased rate of accumulation of nitrogen in shoots that was accompanied by a rapid cessation of leaf development between days 6 and 13. The decline in leaf growth rate of NH4(+) -fed plants at pH 4.0 was followed by reductions in photosynthetic rate per unit leaf area. These responses of NH4(+) -fed plants to increased root-zone acidity are characteristic of the sequence of responses that occur during onset of nitrogen stress.

Description: Studies on the diurnal variations of nitrate reductase (NR) activity during the life cycle of synchronized Chlorella sorokiniana cells grown with a 7:5 light-dark cycle showed that the NADH:NR activity, as well as the NR partial activities NADH:cytochrome c reductase and reduced methyl viologen:NR, closely paralleled the appearance and disappearance of NR protein as shown by sodium dodecyl sulfate gel electrophoresis and immunoblots. Results of pulse-labeling experiments with [35S]methionine further confirmed that diurnal variations of the enzyme activities can be entirely accounted for by the concomitant synthesis and degradation of the NR protein.

Description: The high performance liquid chromatographic (HPLC) method of Flores and Galston (1982 Plant Physiol 69: 701) for the separation and quantitation of benzoylated polyamines in plant tissues has been widely adopted by other workers. However, due to previously unrecognized problems associated with the derivatization of agmatine, this important intermediate in plant polyamine metabolism cannot be quantitated using this method. Also, two polyamines, putrescine and diaminopropane, also are not well resolved using this method. A simple modification of the original HPLC procedure greatly improves the separation and quantitation of these amines, and further allows the simulation analysis of phenethylamine and tyramine, which are major monoamine constituents of tobacco and other plant tissues. We have used this modified HPLC method to characterize amine titers in suspension cultured carrot (Daucas carota L.) cells and tobacco (Nicotiana tabacum L.) leaf tissues.

Description: Hemerocallis plantlets maintained in vitro for extended periods of time in tightly closed culture vessels frequently show a phenotype, albeit on a miniaturized scale, typical of more mature, field-grown plants. The positive relationship of elevated ethylene in the headspace of such vessels to the phase shift from juvenile to mature form is established. Rigorous restriction in air exchange with the external environment by means of silicone grease seals hastens the phase change and improves uniformity of response. Although some plantlets may take longer to accumulate enough ethylene in sealed jars to undergo change, added ethylene and ethylene-releasing agents promote it. Ethylene adsorbants (e.g. mercuric perchlorate) block the shift of juvenile to mature form. Critical ambient ethylene level for the shift is ca 1 microliter l-1. Levels up to 1000 microliters l-1 do not hasten the response but are not toxic. The phase change is fully reversible when air exchange permits ethylene to drop below 1 microliter l-1. At least 1 microliter l-1 ethylene is required to sustain the mature phenotype. The ethylene synthesis inhibitor aminoethoxyvinylglycine (AVG) prevents the phase change, while the ethylene biosynthesis intermediate 1-aminocyclopropanecarboxylic acid (ACC) improves it. KOH, as a CO2 absorbent, does not prevent the phase change. Histology sections demonstrate subtle changes in the form of shoot tips of plantlets undergoing phase change.

Description: Published evidence suggests a role for dopaminergic (DA) brain pathways in feeding-associated behaviors. Using the novel technique of brain microdialysis of striatal extracellular fluid (ECF) as an index of DA release, Church et al. described increases in levels of DA when animals had limited access to pellets, but not with free access. Dopamine release from the nucleus accumbens did increase with free access to pellets post starvation or after food reward. We used permanently implanted microdialysis probes to measure ECF levels of DA, DOPAC, HVA, and large neutral amino acids (LNAA) for up to 72 hours after implantation among rats experiencing different dietary regimens.

Description: We show the equivalence of semi-classical solutions to optical model coupled-channel equations derived from Watson's form of the nucleus-nucleus multiple-scattering series to the Glauber multiple-scattering series. A second-order solution to the semi-classical coupled-channel elastic amplitude is shown to be nearly equivalent to a second-order optical-phase-shift approximation to the Glauber amplitude if the densities of all nuclear excited states are approximated by the ground-state density. Using the Jastrow method to model the two-body density we find an average excited-state density to be of negligible importance in the double-scattering region of alpha-alpha scattering.

Description: The compartment syndrome is defined as a condition in which high pressure within a closed fascial space (muscle compartment) reduces capillary blood perfusion below the level necessary for tissue viability'. This condition occurs in acute and chronic (exertional) forms, and may be secondary to a variety of causes. The end-result of an extended period of elevated intramuscular pressure may be the development of irreversible tissue injury and Volkmann's contracture. The goal of treatment of the compartment syndrome is the reduction of intracompartmental pressure thus facilitating reperfusion of ischaemic tissue and this goal may be achieved by decompressive fasciotomy. Controversy exists regarding the critical pressure-time thresholds for surgical decompression and the optimal diagnostic methods of measuring intracompartmental pressures. This paper will update and review some current knowledge regarding the pathophysiology, aetiology, diagnosis, and treatment of the acute compartment syndrome.

Description: Phytochrome-mediated germination of fern spores of Dryopteris paleacea Sw. was initiated by a saturating red-light (R) irradiation after 20 h of imbibition. For its realization external Ca2+ was required, with a threshold at a submicromolar concentration, and an optimum was reached around 10(-4) M. At concentrations 〉 or = 10(-1) M only a reduced response was obtained, based probably on an unspecific osmotic or ionic effect. The germination response was inhibited by La3+, an antagonist of Ca2+. From these results it is concluded that Ca2+ influx from the medium into the spores may be an important event in phytochrome-mediated germination. In the absence of Ca2+ the R-stimulated system remained capable of responding to Ca2+, added as late as 40 h after R. Moreover, Ca2+ was effective even if added after the active form of phytochrome, Pfr, had been abolished by far-red (FR) 24 h after R. Thus, the primary effect of Pfr, that initiates the transduction chain, does not require calcium. "Coupling" of Pfr to subsequent dark reactions has been investigated by R-FR irradiations with various dark intervals. The resulting "escape kinetics" were characterized by a lag phase (6 h) and half-maximal escape from FR reversibility (19 h). These kinetics were not significantly changed by the presence or absence of calcium. Thus, direct interaction of Pfr and calcium is not a step in the transduction chain initiated by the active form of phytochrome.

Description: Plasmodesmata linking the root cap and root in primary roots Zea mays are restricted to approx. 400 protodermal cells bordering approx. 110000 microns2 of the calyptrogen of the root cap. This area is less than 10% of the cross-sectional area of the root-tip at the cap junction. Therefore, gravitropic effectors moving from the root cap to the root can move symplastically only through a relatively small area in the centre of the root. Decapped roots are non-responsive to gravity. However, decapped roots whose caps are replaced immediately after decapping are strongly graviresponsive. Thus, gravicurvature occurs only when the root cap contacts the root, and symplastic continuity between the cap and root is not required for gravicurvature. Completely removing mucilage from the root tip renders the root non-responsive to gravity. Taken together, these data suggest that gravitropic effectors move apoplastically through mucilage from the cap to the root.

Description: The authors provide an overview of papers presented at a workshop on Biomedical and Space-Related Research with Heavy Ions at the BEVALAC at Lawrence Berkeley Laboratory. Goals of the meeting were to determine the critical experiments using heavy ions as probes in radiation physics, radiation chemistry, macromolecular and cellular biology, evolution science, basic neurophysiology, and medical therapies; how beam lines and facilities at Lawrence Berkeley Laboratory can be improved for these experiments; and implications in priorities and funding for national policy. Workshop topics included physics and facilities, cellular and molecular biology, tissue radiobiology, and the future of heavy ion research.

Description: A chloroplast type of fructose-1,6-bisphosphatase, a central regulatory enzyme of photosynthetic carbon metabolism, has been partially purified from Chlamydomonas reinhardtii. Unlike its counterpart from spinach chloroplasts, the algal FBPase showed a strict requirement for a dithiol reductant irrespective of Mg2+ concentration. The enzymes from the two sources resembled each other immunologically, in subunit molecular mass and response to pH. In the presence of dithiothreitol, the pH optimum for both the algal and spinach enzymes shifted from 8.5 to a more physiologic value of 8.0 as the Mg2+ concentration was increased from 1 to 16 mM. At 1 mM Mg2+, a concentration estimated to be close to physiological, the Chlamydomonas FBPase was active only in the presence of reduced thioredoxin and was most active with Chlamydomonas thioredoxin f. Under these conditions, the enzyme showed a pH optimum of 8.0. The data suggest that the Chlamydomonas enzyme resembles its spinach counterpart in most respects, but it has a stricter requirement for reduction and less strict reductant specificity. A comparison of the properties of the FBPases from Chlamydomonas and spinach will be helpful for elucidating the mechanism of the reductive activation of this enzyme.

Description: Green alga Scenedesmus obliquus was studied as one of the potential sources of macronutrients in a space habitat. Algal protein concentrate (70.5% protein) was incorporated into a variety of food products such as bran muffins, fettuccine (spinach noodle imitation) and chocolate chip cookies. Food products containing 20 to 40% of incorporated algal proteins were considered. In the sensory analysis the greenish color of the bran muffins and cookies was not found to be objectional. The mild spinachy flavor (algae flavor) was less detectable in chocolate chip cookies than in bran muffins. The color and taste of the algae noodles were found to be pleasant and compared well with commercially available spinach noodles. Commercially available spray-dried Spirulina algae was also incorporated so the products can be compared with those containing Scenedesmus obliquus concentrate. Food products containing commercial algae had a dark green color and a "burnt after taste" and were less acceptable to the panelists.

Description: Excised zygotic embryos, mericarps ("seeds") and hypocotyls of seedlings of cultivated carrot Daucus carota cv. Scarlet Nantes were evaluated for their ability to generate somatic embryos on a semisolid hormone-free nutrient medium. Neither intact zygotic embryos nor hypocotyls ever produced somatic embryos. However, mericarps and broken zygotic embryos were excellent sources for somatic embryo production (response levels as high as 86%). Somatic embryo formation was highest from cotyledons, but was also observed on isolated hypocotyls and root tips of mature zygotic embryos. On media containing unreduced nitrogen, somatic embryo formation led to the generation of vigorous cultures comprised entirely of somatic embryos at various stages of development which in turn proliferated still other somatic embryos. However, a medium was devised which when 1-5 mM NH4+ was the sole nitrogen source, led only to a proliferation of globular proembryos. Sustained subculturing of these proembryos at 2-3 week intervals enabled establishment of highly uniform cultures in which no further development into more mature stages of embryonic development occurred. These have been maintained, without decline, as morphogenetically competent proembryonic globules for over ten months. A basal medium containing from 1-5 mM NH4+ as the sole nitrogen source appears not to be inductive to somatic proembryo formation. Instead, such a medium is best thought of as permissive to the expression of embryogenically determined cells within zygotic embryos. By excising and breaking or wounding zygotic embryos, constituent cells are probably released from positional or chemical restraints and thus are able to express their innate embryogenic potential. Once a proembryonic culture is established, this medium containing 1-5 mM NH4+ as the sole nitrogen source provides a nonpermissive environment to the development and growth of later embryonic stages, but it does allow the continued formation and multiplication of globular somatic proembryos. The sequence of events leading from excised broken zygotic embryos to the formation of somatic embryos and the maintenance of somatic proembryos are demonstrated by scanning electron microscopy and histological preparations. Germination levels from intact zygotic embryos on media with varying levels and ratios of unreduced vs. reduced inorganic nitrogen were determined as well and provided baseline or control data on the type of response obtained from nonwounded material.

Description: The main biological processes presently considered for applications in space laboratories are: (i) bioseparation, (ii) cell cultivation and (iii) cell electrofusion. All three technologies were discussed by experts in the field at the 1988-COSPAR Meeting in Helsinki.

Description: The effect of salinity stress on metabolic heat output of barley (Hordeum vulgare L.) root tips was measured by isothermal microcalorimetry. Several varieties differing in tolerance to salinity were compared and differences quantified. Two levels of inhibition by increasing salt were found. Following the transition from the initial rate of the first level, inhibition remained at about 50% with further increases in salt concentration up to 150 millimolar. The concentration of salt required to inhibit to this level was cultivar dependent. At highter concentrations (〉150 millimolar) of salt, metabolism was further decreased. This decrease was not cultivar dependent. The decreased rate of metabolic heat output at the first transition could be correlated with decreases in uptake of NO3-, NH4+, and Pi that occurred as the salt concentration was increased. The high degree of dependence of the inhibition of metabolic heat output on NaCl concentration points to a highly cooperative reaction responsible for the general inhibition of metabolism and nutrient uptake. The time required to attain the first level of salt inhibition is less than 20 minutes. Inhibition of root tips was not reversible by washing with salt free solutions. In addition to revealing these features of salt inhibition, isothermal microcalorimetry is a promising method for convenient and rapid determination of varietal differences in response to increasing salinity.

Description: Endogenous calcium (Ca) accumulates along the lower side of the elongating zone of horizontally oriented roots of Zea mays cv. Yellow Dent. This accumulation of Ca correlates positively with the onset of gravicurvature, and occurs in the cytoplasm, cell walls and mucilage of epidermal cells. Corresponding changes in endogenous Ca do not occur in cortical cells of the elongating zone of intact roots. These results indicate that the calcium asymmetries associated with root gravicurvature occur in the outermost layers of the root.

Description: Lipophilic pigments were examined in microbial mat communities dominated by cyanobacteria in the intertidal zone and by diatoms in the subtidal and sublittoral zones of Hamelin Pool, Shark Bay, Western Australia. These microbial mats have evolutionary significance because of their similarity to lithfied stromatolites from the Proterozoic and Early Paleozoic eras. Fucoxanthin, diatoxanthin, diadinoxanthin, beta-carotene, and chlorophylls a and c characterized the diatom mats, whereas cyanobacterial mats contained myxoxanthophyll, zeaxanthin, echinenone, beta-carotene, chlorophyll a and, in some cases, sheath pigment. The presence of bacteriochlorophyll a within the mats suggest a close association of photosynthetic bacteria with diatoms and cyanobacteria. The high carotenoids : chlorophyll a ratios (0.84-2.44 wt/wt) in the diatom mats suggest that carotenoids served a photoprotective function in this high light environment. By contrast, cyanobacterial sheath pigment may have largely supplanted the photoprotective role of carotenoids in the intertidal mats.

Description: Three objectives are stated for activities at a proposed manned lunar base. One objective is scientific investigation of the moon and its environment and the application of special properties of the moon to research problems. Another objective would be to produce the capability of using the materials of the moon for beneficial purposes throughout the earth-moon system. The third objective is to conduct research and development leading to a self-sufficient and self-supporting lunar base, the first extraterrestrial human colony. The potential benefits to earth deriving from these moon-based activities, such as technology development and realization, as well as growing industrialization of near-earth space, are addressed.

Description: The evolutionary approach to space development is discussed in the framework of three overall strategies encompassing four case studies. The first strategy, human expeditions, places emphasis on highly visible, near-term manned missions to Mars or to one of the two moons of Mars. These expeditions are similar in scope and objectives to the Apollo program, with infrastructure development only conducted to the degree necessary to support one or two short-duration trips. Two such expeditionary scenarios, one to Phobus and the other to the Mars surface, are discussed. The second strategy involves the construction of science outposts, and emphasizes scientific exploration as well as investigation of technologies and operations needed for permanent habitation. A third strategy, evolutionary expansion, would explore and settle the inner solar system in a series of steps, with continued development of technologies, experience, and infrastructure.

Description: Nonequilibrium phenomena in hypersonic flows are examined on the basis of theoretical models and selected experimental data, in an introduction intended for second-year graduate students of aerospace engineering. Chapters are devoted to the physical nature of gas atoms and molecules, transitions of internal states, the formulation of the master equation of aerothermodynamics, the conservation equations, chemical reactions in CFD, the behavior of air flows in nonequilibrium, experimental aspects of nonequilibrium flow, a review of experimental results, and gas-solid interaction. Diagrams, graphs, and tables of numerical data are provided.

Description: Logistic difficulties associated with the Space Station Freedom are discussed. Proposed ground and on-orbit operations and procedures for supplying the Station are described. The transfer operations of supplies to the modules, the use of expendable launch vehicles for supplying the Station, and the use of EVA suits for assembling and servicing are considered. Ground support activities for resupplying and maintaining the spacecraft are examined.

Description: A technique is described to estimate the area-to-mass ratio of debris fragments using orbital fragments obtained by radar. The area-to-mass ratio of about 2600 fragments arising from the breakup of 24 artificial satellites was determined; an analysis of the data on about 200 objects with known mass, size, and shape has been made, and a calibration of the observed radar cross-section (RCS) to the effective area of these objects has provided a method to estimate the effective area of debris fragments. From the knowledge of the effective area and the estimated area-to-mass ratio, the mass and area distribution of each of the known breakup has been obtained. As a function of time, the orbital elements can be used to invert any propagation algorithm to yield the area-to-mass ratio of an orbiting object.

Description: Plans for the Comet Rendezvous Asteroid Flyby (CRAF) mission are discussed. The CRAF spacecraft and mission configurations are illustrated and the scientific studies planned for the mission are listed. The scientific benefits of the study of comets and asteroids are reviewed and the characteristics of Comet Kopff are outlined. In addition, the structure, propulsion, attitude and articulation control, radio frequency and antenna, power and pyro, command, and data storage subsystems are described.

Description: Preliminary results from Voyager's encounter with Neptune are reviewed. The major events of the encounter are listed and the data on the atmosphere, magnetosphere, and ring-arc region of Neptune are discussed. The communications and photographical techniques used in the mission are examined. In addition, a search for Neptune satellites is considered.

Description: The NASA Space Shuttle Earth Observations Office conducts astronaut training in earth observations, provides orbital documentation for acquisition of data and catalogs, and analyzes the astronaut handheld photography upon the return of Space Shuttle missions. This paper provides backgrounds on these functions and outlines the data constraints, organization, formats, and modes of access within the public domain.

Description: The introduction of transverse velocity fluctuations into a separated shear layer on an airfoil at high angles of attack is presently demonstrated to be an effective separation-control technique. Airfoil aerodynamic characteristics, including poststall lift and drag as well as maximum lift coefficient and stall angle, all exhibited improvements controlled forcing at 20 deg angle of attack led to an increased spreading of the mean velocity profile, together with increased turbulence activity; separation moved from the leading edge to about 80 percent of chord.

Description: The old concept of using the wake of a spacecraft to obtain an ultrahigh vacuum is revisited. A wakeshield can be configured so that a surface of interest does not subtend any walls that could become contaminated, thus it should be possible to achieve a contamination-free, ultrahigh vacuum capability with infinite pumping speed even in the presence of high heat loads and moderate gas loads. This papar analyzes the conceptual design for a Space Ultravacuum Research Facility (SURF), both in a shuttle-attached mode and as a free flyer. It is shown that even in the shuttle-attached mode, it should be possible to obtain vacuum levels equivalent to 10 to the -9th to 10 to the -10th Torr with O and N2 as the primary constituents. As a free flyer the SURF will be limited primarily by the gas load from the process being performed. For chemical beam epitaxy it is shown that equivalent vacuum levels of 10 to the -14th Torr should be possible at 300 km.

Description: Rendezvous missions to earth-crossing asteroids are of interest to NASA, for scientific purposes as well as for technological applications and ecological implications. To provide a comprehensive data base for planners of such missions, a mission opportunity map (MOM) has been created for eight relatively easy-to-access asteroids. A MOM presents such mission data as launch dates, flight times, and launch and postlaunch delta V requirements for all useful mission opportunities. The merits of a MOM are: (1) searches for all useful mission oportunities are completed in the process of generating a MOM, and (2) a MOM provides a clear view of good and bad opportunities, the extent of performance variations, and the repeatability of the missions.

Description: To attain the fundamental goals of cometary exploration, rendezvous and sample return missions are necessary. This paper investigates various trajectory options and provides a comprehensive set of mission opportunities available for launches in the 1990s. The modes of explorations considered are rendezvous and flybys with atomized-sample-return missions. For each type of exploration, the paper describes various classes and modes of trajectories available, their inherent characteristics, and the techniques of identifying useful trajectories. The energy requirement associated with these missions and the performance possibilities are provided.

Description: An extensive investigation of the ways to rendezvous with diverse groups of asteroids residing between 2.0 and 5.0 AU is made, and the extent of achievable missions using the STS upper-stage launch vehicles (IUS 2-Stage/Star-48 or NASA Centaur) is examined. With judicious use of earth, Mars, and Jupiter gravity assists, rendezvous with some asteroids in all regions of space is possible. It is also shown that the STS upper stages are capable of carrying out missions beyond a single rendezvous, namely with several flybys and/or multiple rendezvous.

Description: Preliminary analysis results have been obtained for tests conducted to ascertain whether a distinctive fragmentation 'signature' allows discrimination between launch vehicle upper stage destructions due to hypervelocity particle impacts and internal explosions. An account is presently given of factors controlling the damage pattern created by hypervelocity impacts, and an evaluation is made of the applicability of the simulation results obtained to actual upper stage destruction characterization.

Description: In this paper, mission orbit considerations are addressed for using the Space Shuttle as a telescope platform for observing man-made orbital debris. Computer modeling of various electrooptical systems predicts that such a space-borne system will be able to detect particles as small as 1-mm diameter. The research is meant to support the development of debris- collision warning sensors through the acquisition of spatial distribution and spectral characteristics for debris and testing of detector combinations on a shuttle-borne telescopic experiment. The technique can also be applied to low-earth-orbit-debris environment monitoring systems. It is shown how the choice of mission orbit, season of launch, and time of day of launch may be employed to provide extended periods of favorable observing conditions.

Description: Flow characteristics in the vicinity of the flap of a single-slotted airfoil are presented and analyzed. The flow remained attached over the model surfaces, except in the vicinity of the flap trailing edge where a small region of boundary-layer separation extended over the aft 7 percent of flap chord. The airfoil configuration was tested at a Mach number of 0.09 and a chord Reynolds number of 1.8 x 10 to the 6th in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. The flow was complicated by the presence of a strong, initially inviscid, jet, emanating from the slot between airfoil and flap, and a gradual merging of the main airfoil wake and flap suction-side boundary layer.

Description: The microspacecraft is defined as a fully functional spacecraft whose mass is on the order of 10 kg or less. The results of a recent microspacecraft workshop are reviewed. The workshop concluded that microspacecraft are feasible and can be enabling for missions that require multiple simultaneous measurements displaced in position or very high mission delta-VSDIO-s. The paper includes discussions of science objectives and instruments as well as potential missions. Potential missions include a very close approach to the sun, determining the origin of gamma ray bursters and a search for gravity waves. Technology for microspacecraft is coming from the 'Lightsat' or small satellite community and developments sponsored by the SDIO. Concepts for microspacecraft power and telecommunications subsystems developed at the JPL are presented. Due to their small size, microspacecraft can be launched by traditional chemical rockets and also unconventional launchers such as electromagnetic launchers.

Description: The paper presents launch vehicle and upper-stage options for application to lunar and interplanetary microspacecraft missions. Particular attention is given to the capabilities of Piggyback, small launch vehicles, and large launch vehicles. It is noted that Piggyback options on the Shuttle and expendable launch vehicles enable near-term earth-orbital missions and the potential for lunar and planetary missions if an electric-propulsion upper-stage is developed. Launch systems like the Space Shuttle could be used to launch large members of microspacecraft in 'constellation deployment' and 'shotgun' class missions to a variety of solar-system targets such as the sun, asteroids, comets, the moon, Mars, and Saturn.

Description: The transonic aspect of helicopter flow analysis is addressed. The equations of motion and their implementations are examined, and the computation of real rotor flows is considered. Nonlifting rotor flows, high-speed hover, high advance ratio lifting rotor flows, and strong blade/vortex interaction computations are discussed.

Description: Some of the basic finite-difference schemes that can be used to solve the nonlinear equations that describe unsteady inviscid and viscous transonic flow are reviewed. Numerical schemes for solving the unsteady Euler and Navier-Stokes, boundary-layer, and nonlinear potential equations are described. Emphasis is given to the elementary ideas used in constructing various numerical procedures, not specific details of any one procedure.

Description: The general configuration, development schedule, and capabilities of the NASA International Space Station are reviewed, with an emphasis on the possibilities for long-term measurements of high-energy cosmic and secondary radiation from the main Station spacecraft, coorbiting or polar-orbit platforms, or Station-supported GEO satellites. Also outlined are the organizational structure and the application procedures to be followed by potential users of the Station facilities. Diagrams and drawings are provided.

Description: Plans for space-science experiments on the International Space Station (ISS) are reviewed, with a focus on biological and medical research with implications for manned missions to the moon and planets (in a scenario culminating in the establishment of a space colony by about the year 2018). Both applied biomedical research (determining the limits of human endurance in space and developing CELSS technology to extend them) and basic research (on the physiological response of plants and animals to the space environment) are discussed, and particular attention is given to the design and deployment schedule for the ISS biomedical hardware modules (Life Sciences Module, Centrifuge Module, and Variable-Gravity Research Facility). Also included are diagrams; drawings; photographs; and tables listing the individual experiments, their objectives, and the hardware required.

Description: NASA has instituted a plan for the definition of activities and resources required over the coming decade for the deepening of current understanding of anthropogenic orbital debris, and its effects on future mission operations. This understanding will be the basis of policy definition and policy implementation efforts. The most immediate requirement is the definition of the debris environment, with emphasis on data for debris sizes smaller than 4 cm. Systems-damage criteria and hypervelocity-impact theory will then be used to define the hazard to specific spacecraft.

Description: The albedo of upper-stage breakup debris is proposed as an accurate discriminator among the various possible causes of breakup, which encompass residual fuel explosions and hypervelocity particle impacts. The fragments from an impact are covered with a thin layer of soot deposited from the destruction of polymeric circuit boards, while pressure vessel explosion fragments can be expected to remain soot-free. Albedo also facilitates the interpretation of small-debris optical telescope measurements.

Description: The flight testing conducted over the past 10 years in the NASA laminar-flow control (LFC) will be reviewed. The LFC program was directed towards the most challenging technology application, the high supersonic speed transport. To place these recent experiences in perspective, earlier important flight tests will first be reviewed to recall the lessons learned at that time.

Description: Although most of the laminar flow airfoils recently developed at the NASA Langley Research Center were intended for general aviation applications, low-drag airfoils were designed for transonic speeds and wind tunnel performance tested. The objective was to extend the technology of laminar flow to higher Mach and Reynolds numbers and to swept leading edge wings representative of transport aircraft to achieve lower drag and significantly improved operation costs. This research involves stabilizing the laminar boundary layer through geometric shaping (Natural Laminar Flow, NLF) and active control involving the removal of a portion of the laminar boundary layer (Laminar-Flow Control, LFC), either through discrete slots or perforated surface. Results show that extensive regions of laminar flow with large reductions in skin friction drag can be maintained through the application of passive NLF boundary-layer control technologies to unswept transonic wings. At even greater extent of laminar flow and reduction in the total drag level can be obtained on a swept supercritical airfoil with active boundary layer-control.

Description: Aerodynamic forces and moments for a slender wing-body configuration are summarized from an investigation in the Langley National Transonic Facility (NTF). The results include both longitudinal and lateral-directional aerodynamic properties as well as slideslip derivatives. Results were selected to emphasize Reynolds number effects at a transonic speed although some lower speed results are also presented for context. The data indicate nominal Reynolds number effects on the longitudinal aerodynamic coefficients and more pronounced effects for the lateral-directional aerodynamic coefficients. The Reynolds number sensitivities for the lateral-directional coefficients were limited to high angles of attack.

Description: An interactive, graphical proximity operations planning system was developed which allows on-site design of efficient, complex, multiburn maneuvers in the dynamic multispacecraft environment about the space station. Maneuvering takes place in, as well as out of, the orbital plane. The difficulty in planning such missions results from the unusual and counterintuitive character of relative orbital motion trajectories and complex operational constraints, which are both time varying and highly dependent on the mission scenario. This difficulty is greatly overcome by visualizing the relative trajectories and the relative constraints in an easily interpretable, graphical format, which provides the operator with immediate feedback on design actions. The display shows a perspective bird's-eye view of the space station and co-orbiting spacecraft on the background of the station's orbital plane. The operator has control over two modes of operation: (1) a viewing system mode, which enables him or her to explore the spatial situation about the space station and thus choose and frame in on areas of interest; and (2) a trajectory design mode, which allows the interactive editing of a series of way-points and maneuvering burns to obtain a trajectory which complies with all operational constraints. Through a graphical interactive process, the operator will continue to modify the trajectory design until all operational constraints are met. The effectiveness of this display format in complex trajectory design is presently being evaluated in an ongoing experimental program.

Description: The objective is to provide useful engineering formulations and to instill a modest degree of physical understanding of the phenomena governing convective aerodynamic heating at high flight speeds. Some physical insight is not only essential to the application of the information presented here, but also to the effective use of computer codes which may be available to the reader. Given first is a discussion of cold-wall, laminar boundary layer heating. A brief presentation of the complex boundary layer transition phenomenon follows. Next, cold-wall turbulent boundary layer heating is discussed. This topic is followed by a brief coverage of separated flow-region and shock-interaction heating. A review of heat protection methods follows, including the influence of mass addition on laminar and turbulent boundary layers. Next is a discussion of finite-difference computer codes and a comparison of some results from these codes. An extensive list of references is also provided from sources such as the various AIAA journals and NASA reports which are available in the open literature.

Description: A co-operative testing program is in progress between the Langley Research Center (NASA) and the National Aeronautical Establishment (NAE, Canada) to validate two different techniques of airfoil testing at transonic speeds. The procedure employed is to test the same airfoil model in the NAE two-dimensional tunnel and the Langley 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT). The airfoil model used in testing was CAST-10-2/DOA-2 super-critical airfoil. The Langley 0.3-m TCT has a relatively small cross section of 13 in x 13 in, giving a (h/c) ratio of 1.44 for the same 9 in chord model. The approach employed in the 0.3-m TCT aims towards eliminating the wall effects by using active walls. The top and bottom walls are flexible. By changing the wall shapes during a test in an iterative manner, the wall interference effects are reduced. The method employed to change the wall shapes is the adaptive wall technique. The current test program provided an opportunity to validate the adaptive wall technique in the 0.3-m TCT. The relatively long chord airfoil represents a severe test case to test the efficacy of the adaptive wall technique under cryogenic conditions. The program also involved removal of side wall boundary-layer thus increasing the complexity of the wall adaptation technique. This paper deals with some salient results obtained regarding repeatability of test data and possible residual interference effects.

Description: The Office of Exploration has established a process whereby all NASA field centers and other NASA Headquarters offices participate in the formulation and analysis of a wide range of mission strategies. These strategies were manifested into specific scenarios or candidate case studies. The case studies provided a systematic approach into analyzing each mission element. First, each case study must address several major themes and rationale including: national pride and international prestige, advancement of scientific knowledge, a catalyst for technology, economic benefits, space enterprise, international cooperation, and education and excellence. Second, the set of candidate case studies are formulated to encompass the technology requirement limits in the life sciences, launch capabilities, space transfer, automation, and robotics in space operations, power, and propulsion. The first set of reference case studies identify three major strategies: human expeditions, science outposts, and evolutionary expansion. During the past year, four case studies were examined to explore these strategies. The expeditionary missions include the Human Expedition to Phobos and Human Expedition to Mars case studies. The Lunar Observatory and Lunar Outpost to Early Mars Evolution case studies examined the later two strategies. This set of case studies established the framework to perform detailed mission analysis and system engineering to define a host of concepts and requirements for various space systems and advanced technologies. The details of each mission are described and, specifically, the results affecting the advanced technologies required to accomplish each mission scenario are presented.

Description: The nation's efforts to expand human presence and activity beyond Earth orbit into the solar system was given renewed emphasis in January of 1988 when the Presidential Directive on National Space Policy was signed into effect. The expansion of human presence into the solar system has particular significance, in that it defines long-range goals for NASA's future missions. To embark and achieve such ambitious ventures is a significant undertaking, particularly compared to past space activities. Missions to Mars, the Moon, and Phobos, as well as an observatory based on the dark side of the Moon are discussed.

Description: The two-dimensional (2-D) and three-dimensional Navier-Stokes equations are solved for flow over a NAE CAST-10 airfoil model. Recently developed finite-volume codes that apply a multistage time stepping scheme in conjunction with steady state acceleration techniques are used to solve the equations. Two-dimensional results are shown for flow conditions uncorrected and corrected for wind tunnel wall interference effects. Predicted surface pressures from 3-D simulations are compared with those from 2-D calculations. The focus of the 3-D computations is the influence of the sidewall boundary layers. Topological features of the 3-D flow fields are indicated. Lift and drag results are compared with experimental measurements.

Description: An experimental Adaptive Wall Test Section (AWTS) process is described. Comparisons of the ONERA T2 and the 0.3-m TCT (transonic cryogenic tunnel) AWTS data for the ONERA CAST-10 airfoil are presented. Most of the 0.3-m TCT data is new and preliminary and no sidewall boundary layer control is involved. No conclusions are given.

Description: The transonic airfoil CAST 10-2/DOA 2 was investigated in several major transonic wind tunnels at Reynolds numbers ranging from Re=1.3 x 10(exp 6) to 45 x 10(exp 6) at ambient and cryogenic temperature conditions. The main objective was to study the degree and extent of the effects of Reynolds number on both the airfoil aerodynamic characteristics and the interference effects of various model-wind-tunnel systems. The initial analysis of the CAST 10-2 airfoil results revealed appreciable real Reynolds number effects on this airfoil and showed that wall interference can be significantly affected by changes in Reynolds number thus appearing as true Reynolds number effects.

Description: Hypersonic vehicles operate in a hostile aerothermal environment which has a significant impact on their aerothermostructural performance. Significant coupling occurs between the aerodynamic flow field, structural heat transfer, and structural response creating a multidisciplinary interaction. A long term goal of the Aerothermal Loads Branch at the NASA Langley Research Center is to develop a computational capability for integrated fluid, thermal and structural analysis of aerodynamically heated structures. The integrated analysis capability includes the coupling between the fluid and the structure which occurs primarily through the thermal response of the structure, because: (1) the surface temperature affects the external flow by changing the amount of energy absorbed by the structure, and (2) the temperature gradients in the structure result in structural deformations which alter the flow field and attendant surface pressures and heating rates. In the integrated analysis, a finite element method is used to solve: (1) the Navier-Stokes equations for the flow solution, (2) the energy equation of the structure for the temperature response, and (3) the equilibrium equations of the structure for the structural deformation and stresses.

Description: Wind tunnel wall interference assessment and correction (WIAC) concepts, applications, and typical results are discussed in terms of several nonlinear transonic codes and one panel method code developed for and being implemented at NASA-Langley. Contrasts between 2-D and 3-D transonic testing factors which affect WIAC procedures are illustrated using airfoil data from the 0.3 m Transonic Cryogenic Tunnel and Pathfinder 1 data from the National Transonic Facility. Initial results from the 3-D WIAC codes are encouraging; research on and implementation of WIAC concepts continue.

Description: The stability of compressible 2-D and 3-D boundary layers is reviewed. The stability of 2-D compressible flows differs from that of incompressible flows in two important features: There is more than one mode of instability contributing to the growth of disturbances in supersonic laminar boundary layers and the most unstable first mode wave is 3-D. Whereas viscosity has a destabilizing effect on incompressible flows, it is stabilizing for high supersonic Mach numbers. Whereas cooling stabilizes first mode waves, it destabilizes second mode waves. However, second order waves can be stabilized by suction and favorable pressure gradients. The influence of the nonparallelism on the spatial growth rate of disturbances is evaluated. The growth rate depends on the flow variable as well as the distance from the body. Floquet theory is used to investigate the subharmonic secondary instability.

Description: The treatment of turbulence effects on transonic shock/turbulent boundary layer interaction is addressed within the context of a triple deck approach valid for arbitrary practical Reynolds numbers between 1000 and 10 billion. The modeling of the eddy viscosity and basic turbulent boundary profile effects in each deck is examined in detail using Law-of-the-Wall/Law-of-the-Wake concepts as the foundation. Results of parametric studies showing how each of these turbulence model aspects influences typical interaction zone property distributions (wall pressure, displacement thickness and local skin friction) are presented and discussed.

Description: The aerodynamic characteristics for both single and twin-engine high-performance aircraft are significantly affected by shock induced flow interactions as well as other local flow interference effects which usually occur at transonic speeds. These adverse interactions can not only cause high drag, but also cause unusual aerodynamic loadings and/or severe stability and control problems. Many programs are under way to not only develop method for reducing the adverse effects, but also to develop an understanding of the basic flow conditions which are the primary contributors. It is anticipated that these programs will result in technologies which can reduce the aircraft cruise drag through improved integration as well as increase aircraft maneuverability through the application of thrust vectoring. Some of the primary integration problems for twin-engine aircraft at transonic speeds are identified, and several methods are demonstrated for reducing or eliminating the undersirable characteristics, while enhancing configuration effectiveness.

Description: Algorithms are described for the generation and adaptation of unstructured grids in two and three dimensions, as well as Euler solvers for unstructured grids. The main purpose is to demonstrate how unstructured grids may be employed advantageously for the economic simulation of both geometrically as well as physically complex flow fields.

Description: For many internal transonic flows of practical interest, some of the relevant nondimensional parameters typically are small enough that a perturbation scheme can be expected to give a useful level of numerical accuracy. A variety of steady and unsteady transonic channel and cascade flows is studied with the help of systematic perturbation methods which take advantage of this fact. Asymptotic representations are constructed for small changes in channel cross-section area, small flow deflection angles, small differences between the flow velocity and the sound speed, small amplitudes of imposed oscillations, and small reduced frequencies. Inside a channel the flow is nearly one-dimensional except in thin regions immediately downstream of a shock wave, at the channel entrance and exit, and near the channel throat. A study of two-dimensional cascade flow is extended to include a description of three-dimensional compressor-rotor flow which leads to analytical results except in thin edge regions which require numerical solution. For unsteady flow the qualitative nature of the shock-wave motion in a channel depends strongly on the orders of magnitude of the frequency and amplitude of impressed wall oscillations or fluctuations in back pressure. One example of supersonic flow is considered, for a channel with length large compared to its width, including the effect of separation bubbles and the possibility of self-sustained oscillations. The effect of viscosity on a weak shock wave in a channel is discussed.

Description: The 1980s may well be called the Euler era of applied aerodynamics. Computer codes based on discrete approximations of the Euler equations are now routinely used to obtain solutions of transonic flow problems in which the effects of entropy and vorticity production are significant. Such codes can even predict separation from a sharp edge, owing to the inclusion of artificial dissipation, intended to lend numerical stability to the calculation but at the same time enforcing the Kutta condition. One effect not correctly predictable by Euler codes is the separation from a smooth surface, and neither is viscous drag; for these some form of the Navier-Stokes equation is needed. It, therefore, comes as no surprise to observe that the Navier-Stokes has already begun before Euler solutions were fully exploited. Moreover, most numerical developments for the Euler equations are now constrained by the requirement that the techniques introduced, notably artificial dissipation, must not interfere with the new physics added when going from an Euler to a full Navier-Stokes approximation. In order to appreciate the contributions of Euler solvers to the understanding of transonic aerodynamics, it is useful to review the components of these computational tools. Space discretization, time- or pseudo-time marching and boundary procedures, the essential constituents are discussed. The subject of grid generation and grid adaptation to the solution are touched upon only where relevant. A list of unanswered questions and an outlook for the future are covered.

Description: The application of computational fluid dynamics (CFD) to fighter aircraft design and development is discussed. Methodology requirements for the aerodynamic design of fighter aircraft are briefly reviewed. The state-of-the-art of computational methods for transonic flows in the light of these requirements is assessed and the techniques found most adequate for the subject application are identified. Highlights from some proof-of-feasibility Euler and Navier-Stokes computations about a complete fighter aircraft configuration are presented. Finally, critical issues and opportunities for design application of CFD are discussed.

Description: A brief survey is given on the study of transonic shock/boundary layer effects in flight. Then the possibility of alleviating the adverse shock effects through passive shock control is discussed. A Swedish flight experiment on a swept wing attack aircraft is used to demonstrate how it is possible to reduce the extent of separated flow and increase the drag-rise Mach number significantly using a moderate amount of perforation of the surface.

Description: An iterative method for wall interference assessment and/or correction is presented for transonic flow conditions in wind tunnels equipped with two component velocity measurements on a single interface. The iterative method does not require modeling of the test article and tunnel wall boundary conditions. Analytical proof for the convergence and stability of the iterative method is shown in the subsonic flow regime. The numerical solutions are given for both 2-D and axisymmetrical cases at transonic speeds with the application of global Mach number correction.

Description: An intense research effort over the last few years has produced several competing and apparently diverse methods for generating meshes. Recent progress is reviewed and the central themes are emphasized which form a solid foundation for future developments in mesh generation.

Description: A cell-vertex scheme is outlined for solving the flow about a delta wing with M (sub infinity) is greater than 1. Embedded regions of mesh refinement allow solutions to be obtained which have much higher resolution than those achieved to date. Effects of mesh refinement and artificial viscosity on the solutions are studied, to determine at what point leading-edge vortex solutions are grid-converged. A macroscale and a microscale for the size of the vortex are defined, and it is shown that the macroscale (which includes the wing surface properties) is converged on a moderately refined grid, while the microscale is very sensitive to grid spacing. The level of numerical diffusion in the core of the vortex is found to be substantial. Comparisons with the experiment are made for two cases which have transonic cross-flow velocities.

Description: A computer analysis was developed for calculating steady (or unsteady) three-dimensional aircraft component flow fields. This algorithm, called ENS3D, can compute the flow field for the following configurations: diffuser duct/thrust nozzle, isolated wing, isolated fuselage, wing/fuselage with or without integrated inlet and exhaust, nacelle/inlet, nacelle (fuselage) afterbody/exhaust jet, complete transport engine installation, and multicomponent configurations using zonal grid generation technique. Solutions can be obtained for subsonic, transonic, or hypersonic freestream speeds. The algorithm can solve either the Euler equations for inviscid flow, the thin shear layer Navier-Stokes equations for viscous flow, or the full Navier-Stokes equations for viscous flow. The flow field solution is determined on a body-fitted computational grid. A fully-implicit alternating direction implicit method is employed for the solution of the finite difference equations. For viscous computations, either a two layer eddy-viscosity turbulence model or the k-epsilon two equation transport model can be used to achieve mathematical closure.

Description: The use of computational methods for three dimensional transonic flow design and analysis at the Boeing Company is presented. A range of computational tools consisting of production tools for every day use by project engineers, expert user tools for special applications by computational researchers, and an emerging tool which may see considerable use in the near future are described. These methods include full potential and Euler solvers, some coupled to three dimensional boundary layer analysis methods, for transonic flow analysis about nacelle, wing-body, wing-body-strut-nacelle, and complete aircraft configurations. As the examples presented show, such a toolbox of codes is necessary for the variety of applications typical of an industrial environment. Such a toolbox of codes makes possible aerodynamic advances not previously achievable in a timely manner, if at all.

Description: Progress in a recently started project aimed at the prediction of transition to turbulence in hypersonic flow is briefly discussed. The prediction of transition to turbulence is a very important issue in the design of space vessels. Two space vehicles currently under investigation, namely the aeroassisted transfer vehicle (AOTV) and the trans-atmospheric vehicle (TAV), suffer from strong aerodynamic heating. This heating is strongly influenced by the boundary layer structure. These aerospace vehicles fly in the upper atmospheric layer at a Mach number between 10 and 30 at very low atmospheric pressures. At very high altitudes the flow is laminar, but when the space vessel returns to a lower orbit, the flow becomes turbulent and the heating is dramatically increased. The prediction of this transition process is commonly done by means of experiments. The experimental facilities available nowadays cannot model the hypersonic flow field accurately enough by limitations in Mach and Reynolds number. These facilities also have a large free stream disturbance level which makes it very difficult to investigate transition accurately. An alternative approach is to study transition by theoretical means. Up to now numerical studies of hypersonic flow only discussed steady laminar or turbulent flow. This theoretical approach is extended to the study of transition in hypersonic flow by means of direct numerical simulations and additional theoretical investigations to explain the mechanisms leading to transition. A brief outline of how this research is to be performed is given.

Description: In the past decade, there has been much activity in the development of computational methods for the analysis of unsteady transonic aerodynamics about airfoils and wings. Significant features are illustrated which must be addressed in the treatment of computational transonic unsteady aerodynamics. The flow regimes for an aircraft on a plot of lift coefficient vs. Mach number are indicated. The sequence of events occurring in air combat maneuvers are illustrated. And further features of transonic flutter are illustrated. Also illustrated are several types of aeroelastic response which were encountered and which offer challenges for computational methods. The four cases illustrate problem areas encountered near the boundaries of aircraft envelopes, as operating condition change from high speed, low angle conditions to lower speed, higher angle conditions.

Description: A unified formulation is presented based on the full potential framework coupled with an appropriate structural model to compute steady and unsteady flows over rigid and flexible configurations across the Mach number range. The unsteady form of the full potential equation in conservation form is solved using an implicit scheme maintaining time accuracy through internal Newton iterations. A flux biasing procedure based on the unsteady sonic reference conditions is implemented to compute hyperbolic regions with moving sonic and shock surfaces. The wake behind a trailing edge is modeled using a mathematical cut across which the pressure is satisfied to be continuous by solving an appropriate vorticity convection equation. An aeroelastic model based on the generalized modal deflection approach interacts with the nonlinear aerodynamics and includes both static as well as dynamic structural analyses capability. Results are presented for rigid and flexible configurations at different Mach numbers ranging from subsonic to supersonic conditions. The dynamic response of a flexible wing below and above its flutter point is demonstrated.

Description: One of the most important uses of method that calculate unsteady aerodynamic loads is to predict and analyze the aeroelastic responses of flight vehicles. Currently, methods based on transonic small disturbance potential aerodynamics are the primary tools for aeroelastic analysis. Flow solutions obtained using isentropic potential theory can be highly inaccurate and even multivalued, because they do not model the effects of entropy that is produced when shock waves are in the flow field. From the results that are presented, it is concluded that nonisentropic potential methods more accurately model Euler solutions than do isentropic methods. The primary effects of modeling shock generated entropy are: (1) to eliminate mulitple flow solutions when strong shock waves are in the flow field; and (2) to bring the strengths and locations of computed shock waves into better agreement with those calculated using Euler method and those measured during experiments.

Description: A finite difference technique is used to solve the transonic small disturbance flow equation making use of shock capturing to treat wave discontinuities. Thus the nonlinear effects of thickness and angle of attack are considered. Such an approach is made feasible by the development of a new code called CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance), and is based on a fully implicit approximate factorization (AF) finite difference method to solve the time dependent transonic small disturbance equation. The application of the CAP-TSD code to the calculation of low to moderate supersonic steady and unsteady flows is presented. In particular, comparisons with exact linear theory solutions are made for steady and unsteady cases to evaluate shock capturing and other features of the current method. In addition, steady solutions obtained from an Euler code are used to evaluate the small disturbance aspects of the code. Steady and unsteady pressure comparisons are made with measurements for an F-15 wing model and for the RAE tailplane model.

Description: Two wind tunnel investigations were conducted to assess two different wall interference alleviation/correction techniques: adaptive test section walls and classical analytical corrections. The same airfoil model has been tested in the adaptive wall test section of the NASA-Langley 0.3 m Transonic Cryogenic Tunnel (TCT) and in the National Aeronautical Establishment (NAE) High Reynolds Number 2-D facility. The model has a 9 in. chord and a CAST 10-2/DOA 2 airfoil section. The 0.3 m TCT adaptive wall test section has four solid walls with flexible top and bottom walls. The NAE test section has porous top and bottom walls and solid side walls. The aerodynamic results corrected for top and bottom wall interference at Mach numbers from 0.3 to 0.8 at a Reynolds number of 10 by 1,000,000. Movement of the adaptive walls was used to alleviate the top and bottom wall interference in the test results from the NASA tunnel.

Description: Nonintrusive measurements were made of a normal shock wave/boundary layer interaction. Two dimensional measurements were made throughout the interaction region while 3-D measurements were made in the vicinity of the shock wave. The measurements were made in the corner of the test section of a continuous supersonic wind tunnel in which a normal shock wave had been stabilized. Laser Doppler Anemometry, surface pressure measurement and flow visualization techniques were employed for two freestream Mach number test cases: 1.6 and 1.3. The former contained separated flow regions and a system of shock waves. The latter was found to be far less complicated. The results define the flow field structure in detail for each case.

Description: Three dimensional linear secondary instability theory is extended for compressible boundary layers on a flat plate in the presence of finite amplitude Tollmien-Schlichting waves. The focus is on principal parametric resonance responsible for strong growth of subharmonics in low disturbance environment.

Description: A review is made of the performance of a variety of turbulence models in the evaluation of a particular well documented transonic flow. This is done to supplement a previous attempt to calibrate and verify transonic airfoil codes by including many more turbulence models than used in the earlier work and applying the calculations to an experiment that did not suffer from uncertainties in angle of attack and was free of wind tunnel interference. It is found from this work, as well as in the earlier study, that the Johnson-King turbulence model is superior for transonic flows over simple aerodynamic surfaces, including moderate separation. It is also shown that some field equation models with wall function boundary conditions can be competitive with it.