ALBERT

Description: A summary is presented of vortex control applications and current techniques for the control of longitudinal vortices produced by bodies, leading edges, tips and intersections. Vortex control has up till now been performed by many approaches in an empirical fashion, assisted by the essentially inviscid nature of much of longitudinal vortex behavior. Attention is given to Reynolds number sensitivities, vortex breakdown and interactions, vortex control on highly swept wings, and vortex control in juncture flows.

Description: The flow-field within an axial flow turbomachine, such as a turbine or compressor, is extremely complex because of three-dimensional features such as hub-corner stall, tip-leakage flows, and airfoil wakes. These flow features interact with each other and with rotor and stator airfoils inducing time-varying forces on the airfoils. These complicated rotor-stator interactions must be understood in order to design turbomachines that are light and compact as well as reliable and efficient. Two codes, STAGE-2 and STAGE-3, have been developed to compute these unsteady rotor-stator interaction flows in multistage turbomachines. An implicit, thin-layer Euler/Navier-Stokes zonal algorithm is used to compute the unsteady flow-field within both turbine and compressor configurations. Results include surface pressures and wake profiles for two-dimensional turbine and compressor configurations and surface pressures for a three-dimensional single-stage turbine configuration. The results compare well with experimental data and other unsteady computations.

Description: Jet noise and jet-induced structural loads have become key issues in the design of commercial and military aircraft. Computational Fluid Dynamics (CFD) can be of use in predicting the underlying jet shear-layer instabilities and, in conjunction with classical acoustic theory, jet noise. The computational issues involved in the resolution of high Reynolds number unsteady jet flows are addressed in this paper. Once these jet flows can be accurately resolved, it should be possible to use acoustic theory to extract, for example, the far-field jet noise. An assessment of future work and computational resources required for directly computing far-field jet noise is also presented.

Description: This computer program is designed to calculate the flow fields in two-dimensional and three-dimensional axisymmetric supersonic inlets. The method of characteristics is used to compute arrays of points in the flow field. At each point the total pressure, local Mach number, local flow angle, and static pressure are calculated. This program can be used to design and analyze supersonic inlets by determining the surface compression rates and throat flow properties. The program employs the method of characteristics for a perfect gas. The basic equation used in the program is the compatibility equation which relates the change in stream angle to the change in entropy and the change in velocity. In order to facilitate the computation, the flow field behind the bow shock wave is broken into regions bounded by shock waves. In each region successive rays are computed from a surface to a shock wave until the shock wave intersects a surface or falls outside the cowl lip. As soon as the intersection occurs a new region is started and the previous region continued only in the area in which it is needed, thus eliminating unnecessary calculations. The maximum number of regions possible in the program is ten, which allows for the simultaneous calculations of up to nine shock waves. Input to this program consists of surface contours, free-stream Mach number, and various calculation control parameters. Output consists of printed and/or plotted results. For plotted results an SC-4020 or similar plotting device is required. This program is written in FORTRAN IV to be executed in the batch mode and has been implemented on a CDC 7600 with a central memory requirement of approximately 27k (octal) of 60 bit words.

Description: This program was developed to predict turbine stage performance taking into account the effects of complex passage geometries. The method uses a quasi-3D inviscid-flow analysis iteratively coupled to calculated losses so that changes in losses result in changes in the flow distribution. In this manner the effects of both the geometry on the flow distribution and the flow distribution on losses are accounted for. The flow may be subsonic or shock-free transonic. The blade row may be fixed or rotating, and the blades may be twisted and leaned. This program has been applied to axial and radial turbines, and is helpful in the analysis of mixed flow machines. This program is a combination of the flow analysis programs MERIDL and TSONIC coupled to the boundary layer program BLAYER. The subsonic flow solution is obtained by a finite difference, stream function analysis. Transonic blade-to-blade solutions are obtained using information from the finite difference, stream function solution with a reduced flow factor. Upstream and downstream flow variables may vary from hub to shroud and provision is made to correct for loss of stagnation pressure. Boundary layer analyses are made to determine profile and end-wall friction losses. Empirical loss models are used to account for incidence, secondary flow, disc windage, and clearance losses. The total losses are then used to calculate stator, rotor, and stage efficiency. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370/3033 under TSS with a central memory requirement of approximately 4.5 Megs of 8 bit bytes. This program was developed in 1985.

Description: Turbomachinery components are often connected by ducts, which are usually annular. The configurations and aerodynamic characteristics of these ducts are crucial to the optimum performance of the turbomachinery blade rows. The ANDUCT computer program was developed to calculate the velocity distribution along an arbitrary line between the inner and outer walls of an annular duct with axisymmetric swirling flow. Although other programs are available for duct analysis, the use of the velocity gradient method makes the ANDUCT program fast and convenient while requiring only modest computer resources. A fast and easy method of analyzing the flow through a duct with axisymmetric flow is the velocity gradient method, also known as the stream filament or streamline curvature method. This method has been used extensively for blade passages but has not been widely used for ducts, except for the radial equilibrium equation. In ANDUCT, a velocity gradient equation derived from the momentum equation is used to determine the velocity variation along an arbitrary straight line between the inner and outer wall of an annular duct. The velocity gradient equation is used with an assumed variation of meridional streamline curvature. Upstream flow conditions may vary between the inner and outer walls, and an assumed total pressure distribution may be specified. ANDUCT works best for well-guided passages and where the curvature of the walls is small as compared to the width of the passage. The ANDUCT program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 60K of 8 bit bytes. The ANDUCT program was developed in 1982.

Description: The Panel Code for Planar Cascades was developed as an aid for the designer of turbomachinery blade rows. The effective design of turbomachinery blade rows relies on the use of computer codes to model the flow on blade-to-blade surfaces. Most of the currently used codes model the flow as inviscid, irrotational, and compressible with solutions being obtained by finite difference or finite element numerical techniques. While these codes can yield very accurate solutions, they usually require an experienced user to manipulate input data and control parameters. Also, they often limit a designer in the types of blade geometries, cascade configurations, and flow conditions that can be considered. The Panel Code for Planar Cascades accelerates the design process and gives the designer more freedom in developing blade shapes by offering a simple blade-to-blade flow code. Panel, or integral equation, solution techniques have been used for several years by external aerodynamicists who have developed and refined them into a primary design tool of the aircraft industry. The Panel Code for Planar Cascades adapts these same techniques to provide a versatile, stable, and efficient calculation scheme for internal flow. The code calculates the compressible, inviscid, irrotational flow through a planar cascade of arbitrary blade shapes. Since the panel solution technique is for incompressible flow, a compressibility correction is introduced to account for compressible flow effects. The analysis is limited to flow conditions in the subsonic and shock-free transonic range. Input to the code consists of inlet flow conditions, blade geometry data, and simple control parameters. Output includes flow parameters at selected control points. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 590K of 8 bit bytes. This program was developed in 1982.

Description: An exact, full-potential-equation model for the steady, irrotational, homoentropic, and homoenergetic flow of a compressible, inviscid fluid through a two-dimensional planar cascade together with its appropriate boundary conditions has been derived. The CAS2D computer program numerically solves an artificially time-dependent form of the actual full-potential-equation, providing a nonrotating blade-to-blade, steady, potential transonic cascade flow analysis code. Comparisons of results with test data and theoretical solutions indicate very good agreement. In CAS2D, the governing equation is discretized by using type-dependent, rotated finite differencing and the finite area technique. The flow field is discretized by providing a boundary-fitted, nonuniform computational mesh. This mesh is generated by using a sequence of conformal mapping, nonorthogonal coordinate stretching, and local, isoparametric, bilinear mapping functions. The discretized form of the full-potential equation is solved iteratively by using successive line over relaxation. Possible isentropic shocks are captured by the explicit addition of an artificial viscosity in a conservative form. In addition, a four-level, consecutive, mesh refinement feature makes CAS2D a reliable and fast algorithm for the analysis of transonic, two-dimensional cascade flows. The results from CAS2D are not directly applicable to three-dimensional, potential, rotating flows through a cascade of blades because CAS2D does not consider the effects of the Coriolis force that would be present in the three-dimensional case. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 200K of 8 bit bytes. The CAS2D program was developed in 1980.

Description: A computer program, QSONIC, has been developed for calculating the full potential, transonic quasi-three-dimensional flow through a rotating turbomachinery blade row. The need for lighter, more efficient turbomachinery components has led to the consideration of machines with fewer stages, each with blades capable of higher speeds and higher loading. As speeds increase, the numerical problems inherent in the transonic regime have to be resolved. These problems include the calculation of imbedded shock discontinuities and the dual nature of the governing equations, which are elliptic in the subcritical flow regions but become hyperbolic for supersonic zones. QSONIC provides the flow analyst with a fast and reliable means of obtaining the transonic potential flow distribution on a blade-to-blade stream surface of a stationary or rotating turbomachine blade row. QSONIC combines several promising transonic analysis techniques. The full potential equation in conservative form is discretized at each point on a body-fitted period mesh. A mass balance is calculated through the finite volume surrounding each point. Each local volume is corrected in the third dimension for any change in stream-tube thickness along the stream tube. The nonlinear equations for all volumes are of mixed type (elliptic or hyperbolic) depending on the local Mach number. The final result is a block-tridiagonal matrix formulation involving potential corrections at each grid point as the unknowns. The residual of each system of equations is solved along each grid line. At points where the Mach number exceeds unity, the density at the forward (sweeping) edge of the volume is replaced by an artificial density. This method calculates the flow field about a cascade of arbitrary two-dimensional airfoils. Three-dimensional flow is approximated in a turbomachinery blade row by correcting for stream-tube convergence and radius change in the through flow direction. Several significant assumptions were made in developing the QSONIC program, including: (1) the flow is inviscid and adiabatic, (2) the flow relative to the blade is steady, (3) the fluid is a perfect gas with constant specific heat, (4) the flow is isentropic and any discontinuities (shocks) are weak enough to be approximated as isentropic jumps, (5) there is no velocity component normal to the stream surface, and (6) the flow relative to a fixed frame in space (absolute velocity) is completely irrotational. These assumptions place some limitations on the application of QSONIC. Sharp leading edges at high incidence and high-Mach-number turbine blade trailing edges with substantial deviation will both cause large velocity peaks on the blade. In addition, the program may have difficulty converging if the passage is nearly choked. Input to QSONIC consists of case control parameters, a geometry description, upstream boundary conditions, and a rotor description. Output includes solution scheme parameters and flow field parameters. A data file is also output which contains data on the solution mesh, surface Mach numbers, surface static pressures, isomachs, and the velocity vector field. This data may be used for further processing or for plotting. The QSONIC is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 500K of 8 bit bytes. QSONIC was developed in 1982.

Description: This computer program, WIND, was developed to numerically solve the exact, full-potential equation for three-dimensional, steady, inviscid flow through an isolated wind turbine rotor. The program automatically generates a three-dimensional, boundary-conforming grid and iteratively solves the full-potential equation while fully accounting for both the rotating and Coriolis effects. WIND is capable of numerically analyzing the flow field about a given blade shape of the horizontal-axis type wind turbine. The rotor hub is assumed representable by a doubly infinite circular cylinder. An arbitrary number of blades may be attached to the hub and these blades may have arbitrary spanwise distributions of taper and of the twist, sweep, and dihedral angles. An arbitrary number of different airfoil section shapes may be used along the span as long as the spanwise variation of all the geometeric parameters is reasonably smooth. The numerical techniques employed in WIND involve rotated, type-dependent finite differencing, a finite volume method, artificial viscosity in conservative form, and a successive overrelaxation combined with the sequential grid refinement procedure to accelerate the iterative convergence rate. Consequently, WIND is cabable of accurately analyzing incompressible and compressible flows, including those that are locally transonic and terminated by weak shocks. Along with the three-dimensional results, WIND provides the results of the two-dimensional calculations to aid the user in locating areas of possible improvement in the aerodynamic design of the blade. Output from WIND includes the chordwise distribution of the coefficient of pressure, the Mach number, the density, and the relative velocity components at spanwise stations along the blade. In addition, the results specify local values of the lift coefficient and the tangent and axial aerodynamic force components. These are also given in integrated form expressing the total torque and the total axial force acting on the shaft. WIND can also be used to analyze the flow around isolated aircraft propellers and helicopter rotors in hover as long as the relative oncoming flow is subsonic. The WIND program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 253K of 8 bit bytes. WIND was developed in 1980.

Description: This computer program calculates the flow field in the supersonic portion of a mixed-compression aircraft inlet at non-zero angle of attack. This approach is based on the method of characteristics for steady three-dimensional flow. The results of this program agree with those produced by the two-dimensional method of characteristics when axisymmetric flow fields are calculated. Except in regions of high viscous interaction and boundary layer removal, the results agree well with experimental data obtained for threedimensional flow fields. The flow field in a variety of axisymmetric mixed compression inlets can be calculated using this program. The bow shock wave and the internal shock wave system are calculated using a discrete shock wave fitting procedure. The internal flow field can be calculated either with or without the discrete fitting of the internal shock wave system. The influence of molecular transport can be included in the calculation of the external flow about the forebody and in the calculation of the internal flow when internal shock waves are not discretely fitted. The viscous and thermal diffussion effects are included by treating them as correction terms in the method of characteristics procedure. Dynamic viscosity is represented by Sutherland's law and thermal conductivity is represented as a quadratic function of temperature. The thermodynamic model used is that of a thermally and calorically perfect gas. The program assumes that the cowl lip is contained in a constant plane and that the centerbody contour and cowl contour are smooth and have continuous first partial derivatives. This program cannot calculate subsonic flow, the external flow field if the bow shock wave does not exist entirely around the forebody, or the internal flow field if the bow flow field is injected into the annulus. Input to the program consists of parameters to control execution, to define the geometry, and the vehicle orientation. Output consists of a list of parameters used, solution planes, and a description of the shock waves. This program is written in FORTRAN IV for batch execution and has been implemented on a CDC 6000 series machine with a central memory requirement of 110K (octal) of 60 bit words when it is overlayed. This flow analysis program was developed in 1978.

Description: This computer program was developed for calculating the subsonic or transonic flow on the hub-shroud mid-channel stream surface of a single blade row of a turbomachine. The design and analysis of blades for compressors and turbines ideally requires methods for analyzing unsteady, three-dimensional, turbulent viscous flow through a turbomachine. Since an exact solution is impossible at present, solutions on two-dimensional surfaces are calculated to obtain a quasi-three dimensional solution. When three-dimensional effects are important, significant information can be obtained from a solution on a cross-sectional surface of the passage normal to the flow. With this program, a solution to the equations of flow on the meridional surface can be carried out. This solution is chosen when the turbomachine under consideration has significant variation in flow properties in the hubshroud direction, especially when input is needed for use in blade-to-blade calculations. The program can also perform flow calculations for annular ducts without blades. This program should prove very useful in the design and analysis of any turbomachine. This program calculates a solution for two-dimensional, adiabatic shockfree flow. The flow must be essentially subsonic, but there may be local areas of supersonic flow. To obtain the solution, this program uses both the finite difference and the quasi-orthogonal (velocity gradient) methods combined in a way that takes maximum advantage of both. The finite-difference method solves a finite-difference equation along the meridional stream surface in a very efficient manner but is limited to subsonic velocities. This approach must be used in cases where the blade aspect ratios are above one, cases where the passage is curved, and cases with low hub-tip-ratio blades. The quasi-orthogonal method solves the velocity gradient equation on the meridional surface and is used if it is necessary to extend the range of solutions into the transonic regime. In general the blade row may be fixed or rotating and the blades may be twisted and leaned. The flow may be axial, radial, or mixed. The upstream and downstream flow conditions can vary from hub to shroud with provisions made for an approximate correction for loss of stagnation pressure. Also, viscous forces are neglected along solution mesh lines running from hub to tip. The capabilities of this program include handling of nonaxial flows without restriction, annular ducts without blades, and specified streamwise loss distributions. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 360 computer with a central memory requirement of approximately 700K of 8 bit bytes. This core requirement can be reduced depending on the size of the problem and the desired solution accuracy. This program was developed in 1977.

Description: A computer program has been developed for the design of supersonic rotor blades where losses are accounted for by correcting the ideal blade geometry for boundary layer displacement thickness. The ideal blade passage is designed by the method of characteristics and is based on establishing vortex flow within the passage. Boundary-layer parameters (displacement and momentum thicknesses) are calculated for the ideal passage, and the final blade geometry is obtained by adding the displacement thicknesses to the ideal nozzle coordinates. The boundary-layer parameters are also used to calculate the aftermixing conditions downstream of the rotor blades assuming the flow mixes to a uniform state. The computer program input consists essentially of the rotor inlet and outlet Mach numbers, upper- and lower-surface Mach numbers, inlet flow angle, specific heat ratio, and total flow conditions. The program gas properties are set up for air. Additional gases require changes to be made to the program. The computer output consists of the corrected rotor blade coordinates, the principal boundary-layer parameters, and the aftermixing conditions. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 7094. This program was developed in 1971.

Description: This program obtains a transonic flow solution on a blade-to-blade surface between blades of a turbomachine. The flow must be essentially subsonic, but there may be locally supersonic flow. The solution is two-dimensional, isentropic, and shock free. The blades may be fixed or rotating. The flow may be axial, radial, or mixed, and there may be a change in stream-channel thickness in the through-flow direction. A loss in relative stagnation pressure may be accounted for. The program input consists of blade and stream-channel geometry, stagnation flow conditions, inlet and outlet flow angles, and blade-to-blade stream-channel weight flow. The output includes blade surface velocities, velocity magnitude and direction at all interior mesh points in the blade-to-blade passage, and streamline coordinates throughout the passage. The transonic solution is obtained by a combination of a finite-difference, stream-function solution and a velocity-gradient solution. The finite-difference solution at a reduced weight flow provides information needed to obtain a velocity-gradient solution. This program is written in FORTRAN IV for batch execution and has been implemented on the IBM 360 computer with a central memory requirement of approximately 36K of 8 bit bytes. This program was developed in 1969 and last updated in 1979.

Description: This program is a revision of an existing program for blade-to-blade aerodynamic analysis of turbomachine blades and it is a simpler program while consistent with related programs. The analysis is for two-dimensional, subsonic, compressible (or incompressible), nonviscous flow in a circular or straight infinite cascade of blades, which may be fixed or rotating. The flow may be axial, radial, or mixed, and the stream channel thickness may change in the through-flow direction. The program input consists of blade and stream channel geometry, total flow conditions, inlet and outlet flow angles, and blade-to-blade stream channel weight flow. The output includes blade surface velocities, velocity magnitude and direction at all interior mesh points in the blade-to-blade passage, and streamline coordinates throughout the passage. This program was developed on an IBM 7094/7044 DCS.

Description: This computer program gives the blade-to-blade solution of the two-dimensional, subsonic, compressible (or incompressible), nonviscous flow problem for a circular or straight infinite cascade of tandem or slotted turbomachine blades. The blades may be fixed or rotating. The flow may be axial, radial , or mixed. The method of solution is based on the stream function using an iterative solution of nonlinear finite-difference equations. These equations are solved using two major levels of iteration. The inner iteration consists of the solution of simultaneous linear equations by successive over-relaxation, using an estimated optimum over-relaxation factor. The outer iteration then changes the coefficients of the simultaneous equations to correct for compressibility. The program input consists of the basic blade geometry, the meridional stream channel coordinates, fluid stagnation conditions, weight flow and flow split through the slot, and inlet and outlet flow angles. The output includes blade surface velocities, velocity magnitude and direction throughout the passage, and the streamline coordinates.

Description: This FORTRAN IV computer program which incorporates the method of characteristics was written to assist in the design of supersonic inlets. There were two objectives: (1) to study a greater variety of supersonic inlet configurations and (2) to reduce the time required for trial-and-error procedures to arrive at optimum inlet design. The computer program was written with the intention of being able to construct a variety of inlet configurations by interchanging specific subroutines. In this manner, greater flexibility of choice was attained, and the time required to program a specific inlet configuration was greatly reduced. The second objective was accomplished by a reformulation of the boundary value problem for hyperbolic equations. By this reformulation of the boundary data, the engineering design quantities, throat Mach number and flow angle, were introduced as direct input quantities to the computer program. As a consequence of introducing the engineering parameters as input, the computer program will calculate the surface contours required to satisfy the specific throat conditions. Inviscid flow is assumed and the method used to calculate the inlet contour results in minimum distortion to the flow in the throat. This program was developed on an IBM 7094.

Description: This program represents a subsonic aerodynamic method for determining the mean camber surface of trimmed noncoplaner planforms with minimum vortex drag. With this program, multiple surfaces can be designed together to yield a trimmed configuration with minimum induced drag at some specified lift coefficient. The method uses a vortex-lattice and overcomes previous difficulties with chord loading specification. A Trefftz plane analysis is used to determine the optimum span loading for minimum drag. The program then solves for the mean camber surface of the wing associated with this loading. Pitching-moment or root-bending-moment constraints can be employed at the design lift coefficient. Sensitivity studies of vortex-lattice arrangements have been made with this program and comparisons with other theories show generally good agreement. The program is very versatile and has been applied to isolated wings, wing-canard configurations, a tandem wing, and a wing-winglet configuration. The design problem solved with this code is essentially an optimization one. A subsonic vortex-lattice is used to determine the span load distribution(s) on bent lifting line(s) in the Trefftz plane. A Lagrange multiplier technique determines the required loading which is used to calculate the mean camber slopes, which are then integrated to yield the local elevation surface. The problem of determining the necessary circulation matrix is simplified by having the chordwise shape of the bound circulation remain unchanged across each span, though the chordwise shape may vary from one planform to another. The circulation matrix is obtained by calculating the spanwise scaling of the chordwise shapes. A chordwise summation of the lift and pitching-moment is utilized in the Trefftz plane solution on the assumption that the trailing wake does not roll up and that the general configuration has specifiable chord loading shapes. VLMD is written in FORTRAN for IBM PC series and compatible computers running MS-DOS. This program requires 360K of RAM for execution. The Ryan McFarland FORTRAN compiler and PLINK86 are required to recompile the source code; however, a sample executable is provided on the diskette. The standard distribution medium for VLMD is a 5.25 inch 360K MS-DOS format diskette. VLMD was originally developed for use on CDC 6000 series computers in 1976. It was originally ported to the IBM PC in 1986, and, after minor modifications, the IBM PC port was released in 1993.

Description: This code was developed to aid design engineers in the selection and evaluation of aerodynamically efficient wing-canard and wing-horizontal-tail configurations that may employ simple hinged-flap systems. Rapid estimates of the longitudinal aerodynamic characteristics of conceptual airplane lifting surface arrangements are provided. The method is particularly well suited to configurations which, because of high speed flight requirements, must employ thin wings with highly swept leading edges. The code is applicable to wings with either sharp or rounded leading edges. The code provides theoretical pressure distributions over the wing, the canard or horizontal tail, and the deflected flap surfaces as well as estimates of the wing lift, drag, and pitching moments which account for attainable leading edge thrust and leading edge separation vortex forces. The wing planform information is specified by a series of leading edge and trailing edge breakpoints for a right hand wing panel. Up to 21 pairs of coordinates may be used to describe both the leading edge and the trailing edge. The code has been written to accommodate 2000 right hand panel elements, but can easily be modified to accommodate a larger or smaller number of elements depending on the capacity of the target computer platform. The code provides solutions for wing surfaces composed of all possible combinations of leading edge and trailing edge flap settings provided by the original deflection multipliers and by the flap deflection multipliers. Up to 25 pairs of leading edge and trailing edge flap deflection schedules may thus be treated simultaneously. The code also provides for an improved accounting of hinge-line singularities in determination of wing forces and moments. To determine lifting surface perturbation velocity distributions, the code provides for a maximum of 70 iterations. The program is constructed so that successive runs may be made with a given code entry. To make additional runs, it is necessary only to add an identification record and the namelist data that are to be changed from the previous run. This code was originally developed in 1989 in FORTRAN V on a CDC 6000 computer system, and was later ported to an MS-DOS environment. Both versions are available from COSMIC. There are only a few differences between the PC version (LAR-14458) and CDC version (LAR-14178) of AERO2S distributed by COSMIC. The CDC version has one main source code file while the PC version has two files which are easier to edit and compile on a PC. The PC version does not require a FORTRAN compiler which supports NAMELIST because a special INPUT subroutine has been added. The CDC version includes two MODIFY decks which can be used to improve the code and prevent the possibility of some infrequently occurring errors while PC-version users will have to make these code changes manually. The PC version includes an executable which was generated with the Ryan McFarland/FORTRAN compiler and requires 253K RAM and an 80x87 math co-processor. Using this executable, the sample case requires about four hours to execute on an 8MHz AT-class microcomputer with a co-processor. The source code conforms to the FORTRAN 77 standard except that it uses variables longer than six characters. With two minor modifications, the PC version should be portable to any computer with a FORTRAN compiler and sufficient memory. The CDC version of AERO2S is available in CDC NOS Internal format on a 9-track 1600 BPI magnetic tape. The PC version is available on a set of two 5.25 inch 360K MS-DOS format diskettes. IBM AT is a registered trademark of International Business Machines. MS-DOS is a registered trademark of Microsoft Corporation. CDC is a registered trademark of Control Data Corporation. NOS is a trademark of Control Data Corporation.

Description: This program provides a wing design algorithm based on modified linear theory which takes into account the effects of attainable leading-edge thrust. A primary objective of the WINGDES2 approach is the generation of a camber surface as mild as possible to produce drag levels comparable to those attainable with full theoretical leading-edge thrust. WINGDES2 provides both an analysis and a design capability and is applicable to both subsonic and supersonic flow. The optimization can be carried out for designated wing portions such as leading and trailing edge areas for the design of mission-adaptive surfaces, or for an entire planform such as a supersonic transport wing. This program replaces an earlier wing design code, LAR-13315, designated WINGDES. WINGDES2 incorporates modifications to improve numerical accuracy and provides additional capabilities. A means of accounting for the presence of interference pressure fields from airplane components other than the wing and a direct process for selection of flap surfaces to approach the performance levels of the optimized wing surfaces are included. An increased storage capacity allows better numerical representation of those configurations that have small chord leading-edge or trailing-edge design areas. WINGDES2 determines an optimum combination of a series of candidate surfaces rather than the more commonly used candidate loadings. The objective of the design is the recovery of unrealized theoretical leading-edge thrust of the input flat surface by shaping of the design surface to create a distributed thrust and thus minimize drag. The input consists of airfoil section thickness data, leading and trailing edge planform geometry, and operational parameters such as Mach number, Reynolds number, and design lift coefficient. Output includes optimized camber surface ordinates, pressure coefficient distributions, and theoretical aerodynamic characteristics. WINGDES2 is written in FORTRAN V for batch execution and has been implemented on a CDC CYBER computer operating under NOS 2.7.1 with a central memory requirement of approximately 344K (octal) of 60 bit words. This program was developed in 1984, and last updated in 1990. CDC and CYBER are trademarks of Control Data Corporation.

Description: Unsteady flow behavior and load characteristics of a 2D VR-7 airfoil with and without a leading-edge slat were studied in the water tunnel of the Aeroflightdynamics Directorate, NASA Ames Research Center. Both airfoils were oscillated sinusoidally between 5 and 25 deg at Re = 200,000 to obtain the unsteady lift, drag, and pitching moment data. A fluorescent dye was released from an orifice located at the leading edge of the airfoil for the purpose of visualizing the boundary layer and wake flow. The flowfield and load predictions of an incompressible Navier-Stokes code based on a velocity-vorticity formulation were compared with the test data. The test and predictions both confirm that the slatted VR-7 airfoil delays both static and dynamic stall as compared to the VR-7 airfoil alone.

Description: The problem of the hypersonic double ellipse in rarefied flow is treated by a particle method using the collision model first described by McDonald (1988). In the approach used here, the computational overhead is reduced by using simple cubic cells. The problem of the definition of complex geometries is addressed by developing an algorithm to define the relation of a body surface to the network of cells.

Description: Program LAURA (Langley Aerothermodynamic Upwind Relaxation Algorithm) is an upwind-biased, point-implicit relaxation algorithm for obtaining the numerical solution to the governing equations for 3D viscous hypersonic flows in chemical and thermal nonequilibrium. The algorithm is derived using a finite-volume formulation in which the inviscid components of flux across cell walls are described with a modified Roe's averaging and with second-order corrections based on Yee's Symmetric Total Variation Diminishing scheme. The code has been applied to Problem 8.2 of this workshop for the case of thermochemical nonequilibrium flow through a nozzle. Chemical reaction rates are defined with the model of Park (1987). Thermal nonequilibrium is modeled using a two-temperature approximation in which the vibrational energies of all molecules are assumed to be in equilibrium at a single temperature which is generally different from the translational-rotational temperature. Two grids were used to define the flow for the original problem, with a stagnation temperature of 6500 K. A third case with a stagnation temperature of 10,000 K is also presented. The solution domain includes the converging nozzle, subsonic flow domain in which the gas is substantially in thermochemical equilibrium and the diverging nozzle, hypersonic flow domain in which the gas is substantially in thermochemical nonequilibrium.

Description: Solutions have been computed and results are presented for Problem 1, the case of Mach 9 transitional flow past a 7 deg half-angle cone at zero incidence. The solutions were computed using a code developed for the integration of the parabolized Navier-Stokes equations. The algorithm employed in the code is based on a Roe-type flux-difference-splitting scheme applied following a finite-volume approach. The basic algorithm has been modified to make it implicit and second-order accurate in the crossflow directions. Results are presented in terms of surface pressure and heat transfer as well as boundary layer profiles of pitot pressure, Mach number, and tangential velocity. The case was recalculated several times in an effort to determine sensitivities to such parameters as grid density, wall temperature, turbulence model parameters, as well as freestream expansion. Comparisons with the experimental data are presented and discussed.

Description: A development status evaluation is presented for the theoretical understanding and design conceptualization of boundary layer control (BLC) systems applicable to supersonic transports, such as the currently envisioned NASA High Speed Civil Transport. By reducing fuel burned, supersonic BLC techniques could expand ranges to Pacific-crossing scales, while lowering sonic boom effects and upper-atmosphere pollution and even reducing skin friction temperature. The critical consideration for supersonic BLC is the presence of wave effects.

Description: Attention is drawn to the influence of preexisting finite-amplitude instabilities on the growth of other disturbances; current design tools for LFC take no notice of this kind of interaction. When a rational accounting is accomplished for the evolution of incoming disturbances in finite-amplitude solutions of the equations of motion, future transition-prediction methods will need to take these wave interactions into account. Attention is given here to interactions in the presence of crossflow vortices and interactions involving Goertler vortices.

Description: A development history and a development-trends evaluation are presented for laminar flow controlled airfoil technologies and design concepts, including the search for 'natural' laminar flow and actively controlled flow via suction through small pores on the airfoil surface. While most NASA activities in this field have been concerned with subsonic aircraft, it has been projected that the control of boundary layer turbulence may be even more critical to the aerodynamic efficiency of supersonic aircraft. Developmental programs for these techniques have been conducted with several modified conventional aircraft.

Description: An account is given of the development history of natural laminar-flow (NLF) airfoil profiles under guidance of an experimentally well-verified theoretical method for the design of airfoils suited to virtually all subcritical applications. This method, the Eppler Airfoil Design and Analysis Program, contains a conformal-mapping method for airfoils having prescribed velocity-distribution characteristics, as well as a panel method for the analysis of potential flow about given airfoils and a boundary-layer method. Several of the NLF airfoils thus obtained are discussed.

Description: Airloads measured on a two-bladed helicopter rotor in flight, from the Tip Aerodynamic and Acoustic Test, are compared with calculations from a comprehensive helicopter analysis (CAMRAD/JA), and the pressures compared with calculations from a full-potential rotor code (FPR). The flight test results cover an advance ratio range from 0.19 to 0.38. The lowest speed case is characterized by the presence of significant blade-vortex interactions. Good correlation of peak-to-peak vortex-induced loads and the corresponding pressures is obtained. The results of the correlation for this two-bladed rotor are substantially similar to the results for three- and four-bladed rotors, concerning the tip vortex core size for best correlation, calculation of the peak-to-peak loads on the retreating side, and calculation of vortex-induced loads on inboard radial stations.

Description: A new CFD potential code, FPX (eXtended Full-Potential), has been developed for application to both helicopters and tilt-rotors. The code solves the unsteady, three-dimensional full potential equation and is an extension of the rotor code, FPR. Both entropy and viscosity corrections are included to enhance the physical modeling capabilities. A number of efficiency related modifications have yielded a factor of two speed-up in the code. An axial flow capability has been added to treat tilt-rotor in forward flight (cruise mode). In order to employ streamwise periodicity and accurately solve for the propagation of acoustic signals in the tip region, an H-H topology has been added to the basic O-H grid system. Computations are performed for the XV-15 Standard and ATB blades at high-speed conditions. Comparisons are made for the blade aerodynamics and the induced fuselage cabin pressure for a range of Mach numbers. Grid generation, wake treatment, and far-field wall treatment are identified as problem areas with recommendations for future research.

Description: A preliminary test/theory correlation evaluation is conducted for wake measurement test results obtained by LDV for a B360 helicopter rotor, at conditions critical to the understanding of wake-rollup and blade-vortex interaction phenomena. The LDV data were complemented by acoustic, blade pressure, rotor performance, and blade/control load measurements.

Description: Analytic expressions have been derived for estimating the nonablating laminar and turbulent boundary-layer convective heating rates on inclined flat surfaces for the Martian atmosphere in thermochemical equilibrium. The equations are valid in the speed and altitude regime where aerobraking would occur at Mars. Comparisons with limited experimental measurements and calculations for CO2 (the Martian atmosphere is 95.6 percent CO2) yielded reasonably good agreement, especially for the ratios of heating rates in CO2 to those in air at the same conditions. In the aerobraking speed regime, the laminar flat surface boundary layer heating rates are 15-25 percent greater at Mars than in air. The differences between the turbulent heating rates are even more pronounced. The turbulent heating rates can be over 50 percent greater at Mars than in air at the same flight conditions.

Description: This code was developed to aid design engineers in the selection and evaluation of aerodynamically efficient wing-canard and wing-horizontal-tail configurations that may employ simple hinged-flap systems. Rapid estimates of the longitudinal aerodynamic characteristics of conceptual airplane lifting surface arrangements are provided. The method is particularly well suited to configurations which, because of high speed flight requirements, must employ thin wings with highly swept leading edges. The code is applicable to wings with either sharp or rounded leading edges. The code provides theoretical pressure distributions over the wing, the canard or horizontal tail, and the deflected flap surfaces as well as estimates of the wing lift, drag, and pitching moments which account for attainable leading edge thrust and leading edge separation vortex forces. The wing planform information is specified by a series of leading edge and trailing edge breakpoints for a right hand wing panel. Up to 21 pairs of coordinates may be used to describe both the leading edge and the trailing edge. The code has been written to accommodate 2000 right hand panel elements, but can easily be modified to accommodate a larger or smaller number of elements depending on the capacity of the target computer platform. The code provides solutions for wing surfaces composed of all possible combinations of leading edge and trailing edge flap settings provided by the original deflection multipliers and by the flap deflection multipliers. Up to 25 pairs of leading edge and trailing edge flap deflection schedules may thus be treated simultaneously. The code also provides for an improved accounting of hinge-line singularities in determination of wing forces and moments. To determine lifting surface perturbation velocity distributions, the code provides for a maximum of 70 iterations. The program is constructed so that successive runs may be made with a given code entry. To make additional runs, it is necessary only to add an identification record and the namelist data that are to be changed from the previous run. This code was originally developed in 1989 in FORTRAN V on a CDC 6000 computer system, and was later ported to an MS-DOS environment. Both versions are available from COSMIC. There are only a few differences between the PC version (LAR-14458) and CDC version (LAR-14178) of AERO2S distributed by COSMIC. The CDC version has one main source code file while the PC version has two files which are easier to edit and compile on a PC. The PC version does not require a FORTRAN compiler which supports NAMELIST because a special INPUT subroutine has been added. The CDC version includes two MODIFY decks which can be used to improve the code and prevent the possibility of some infrequently occurring errors while PC-version users will have to make these code changes manually. The PC version includes an executable which was generated with the Ryan McFarland/FORTRAN compiler and requires 253K RAM and an 80x87 math co-processor. Using this executable, the sample case requires about four hours to execute on an 8MHz AT-class microcomputer with a co-processor. The source code conforms to the FORTRAN 77 standard except that it uses variables longer than six characters. With two minor modifications, the PC version should be portable to any computer with a FORTRAN compiler and sufficient memory. The CDC version of AERO2S is available in CDC NOS Internal format on a 9-track 1600 BPI magnetic tape. The PC version is available on a set of two 5.25 inch 360K MS-DOS format diskettes. IBM AT is a registered trademark of International Business Machines. MS-DOS is a registered trademark of Microsoft Corporation. CDC is a registered trademark of Control Data Corporation. NOS is a trademark of Control Data Corporation.

Description: Since its early beginnings, NASA has been actively involved in the design and testing of airfoil sections for a wide variety of applications. Recently a set of programs has been developed to smooth and scale arbitrary airfoil coordinates. The smoothing program, AFSMO, utilizes both least-squares polynomial and least-squares cubic-spline techniques to iteratively smooth the second derivatives of the y-axis airfoil coordinates with respect to a transformed x-axis system which unwraps the airfoil and stretches the nose and trailing-edge regions. The corresponding smooth airfoil coordinates are then determined by solving a tridiagonal matrix of simultaneous cubic-spline equations relating the y-axis coordinates and their corresponding second derivatives. The camber and thickness distribution of the smooth airfoil are also computed. The scaling program, AFSCL, may then be used to scale the thickness distribution generated by the smoothing program to a specified maximum thickness. Once the thickness distribution has been scaled, it is combined with the camber distribution to obtain the final scaled airfoil contour. The airfoil smoothing and scaling programs are written in FORTRAN IV for batch execution and have been implemented on a CDC CYBER 170 series computer with a central memory requirement of approximately 70K (octal) of 60 bit words. Both programs generate plotted output via CALCOMP type plotting calls. These programs were developed in 1983.

Description: The Supersonic Wing Nonlinear Aerodynamics computer program, LTSTAR, was developed to provide for the estimation of the nonlinear aerodynamic characteristics of a wing at supersonic speeds. This corrected linearized-theory method accounts for nonlinearities in the variation of basic pressure loadings with local surface slopes, predicts the degree of attainment of theoretical leading-edge thrust forces, and provides an estimate of detached leading-edge vortex loadings that result when the theoretical thrust forces are not fully realized. Comparisons of LTSTAR computations with experimental results show significant improvements in detailed wing pressure distributions, particularly for large angles of attack and for regions of the wing where the flow is highly three-dimensional. The program provides generally improved predictions of the wing overall force and moment coefficients. LTSTAR could be useful in design studies aimed at aerodynamic performance optimization and for providing more realistic trade-off information for selection of wing planform geometry and airfoil section parameters. Input to the LTSTAR program includes wing planform data, freestream conditions, wing camber, wing thickness, scaling options, and output options. Output includes pressure coefficients along each chord, section normal and axial force coefficients, and the spanwise distribution of section force coefficients. With the chordwise distributions and section coefficients at each angle of attack, three sets of polars are output. The first set is for linearized theory with and without full leading-edge thrust, the second set includes nonlinear corrections, and the third includes estimates of attainable leading-edge thrust and vortex increments along with the nonlinear corrections. The LTSTAR program is written in FORTRAN IV for batch execution and has been implemented on a CDC 6000 series computer with a central memory requirement of approximately 150K (octal) of 60 bit words. The LTSTAR program was developed in 1980.

Description: The nozzle afterbody is one of the main drag-producing components of an aircraft propulsion system. Thus, considerable effort has been devoted to developing techniques for predicting the afterbody flow field and drag. The RAXJET computer program was developed to predict the transonic, axisymmetric flow over nozzle afterbodies with supersonic jet exhausts and includes the effects of boundary-layer displacement, separation, jet entrainment, and inviscid jet plume blockage. RAXJET iteratively combines the South-Jameson relaxation procedure, the Reshotko-Tucker boundary-layer solution, the Presz separation model, the Dash-Pergament mixing model, and the Dash-Thorpe inviscid plume model into a single, comprehensive model. The approach taken in the RAXJET program requires considerably less computational time than the Navier-Stokes solutions and generally yields results of comparable accuracy. In RAXJET, the viscous-inviscid interaction model is constructed by dividing the afterbody flow field into six separate computational regions: (1) The inviscid external flow solution is based on the relaxation procedure of South and Jameson for solving the exact nonlinear potential flow equation in nonconservative form. (2) The flow field in the inviscid jet exhaust is solved by explicit spatial marching of the conservative finite-difference form of the inviscid flow equations for a uniform composition gas mixture. (3) The properties in the attached boundary-layer region are solved by a modified version of the Reshotko-Tucker integral method for turbulent flows. (4) The analysis of the separated flow region consists of predicting the separation location and calculating the discriminating streamline shape. (5) The jet wake region is determined by either a simple extrapolation model or by an integral method that accounts for entrainment effects. (6) The displacement-thickness distribution arising from entrainment into the jet mixing layer is calculated by the overlaid mixing model. The inviscid external flow solution and inviscid jet exhaust solution provide the necessary flow conditions to calculate the flow in the viscous regions. The viscous and inviscid flow fields are iteratively solved until a final solution is obtained. Input to the RAXJET program consists of body geometry data, free-stream conditions, main logic control parameters, and condition and control parameters for each of the six computational flow regions. Output from RAXJET includes detailed flow results and aerodynamic coefficients. The RAXJET program is written in FORTRAN IV for batch execution and has been implemented on a CDC CYBER 170 series computer with a central memory requirement of approximately 60K(octal) of 60 bit words. The RAXJET program was developed in 1982.

Description: The computer program SALLY was developed to compute the incompressible linear stability characteristics and integrate the amplification rates of boundary layer disturbances on swept and tapered wings. For some wing designs, boundary layer disturbance can significantly alter the wing performance characteristics. This is particularly true for swept and tapered laminar flow control wings which incorporate suction to prevent boundary layer separation. SALLY should prove to be a useful tool in the analysis of these wing performance characteristics. The first step in calculating the disturbance amplification rates is to numerically solve the compressible laminar boundary-layer equation with suction for the swept and tapered wing. A two-point finite-difference method is used to solve the governing continuity, momentum, and energy equations. A similarity transformation is used to remove the wall normal velocity as a boundary condition and place it into the governing equations as a parameter. Thus the awkward nonlinear boundary condition is avoided. The resulting compressible boundary layer data is used by SALLY to compute the incompressible linear stability characteristics. The local disturbance growth is obtained from temporal stability theory and converted into a local growth rate for integration. The direction of the local group velocity is taken as the direction of integration. The amplification rate, or logarithmic disturbance amplitude ratio, is obtained by integration of the local disturbance growth over distance. The amplification rate serves as a measure of the growth of linear disturbances within the boundary layer and can serve as a guide in transition prediction. This program is written in FORTRAN IV and ASSEMBLER for batch execution and has been implemented on a CDC CYBER 70 series computer with a central memory requirement of approximately 67K (octal) of 60 bit words. SALLY was developed in 1979.

Description: An incompressible three-dimensional laminar boundary-layer flow over a swept wing is used as a model to study both the wall-curvature and streamline-curvature effects on the stationary crossflow instability. The basic state is obtained by solving the full Navier-Stokes (N-S) equations numerically. The linear disturbance equations are cast on a fixed, body-intrinsic, curvilinear coordinate system. Those nonparallel terms which contribute mainly to the streamline-curvature effect are retained in the formulation of the disturbance equations and approximated by their local finite difference values. The resulting eigenvalue problem is solved by a Chebyshev collocation method. The present results indicate that the convex wall curvature has a stabilizing effect, whereas the streamline curvature has a destabilizing effect. A validation of these effects with an N-S solution for the linear disturbance flow is provided.

Description: The paper presents a general approach to constructing mean velocity profiles for compressible turbulent boundary layers with isothermal or adiabatic walls. The theory is based on a density-weighted transformation that allows the extension of the incompressible similarity laws of the wall to the compressible regions. The velocity profile family is compared to a range of experimental data, and excellent agreement is obtained. A self-consistent skin friction law, which satisfies the proposed velocity profile family, is derived and compared with the well-known Van Driest II theory for boundary layers in zero pressure gradient. The results are found to be at least as good as those obtained by using the Van Driest II transformation.

Description: A number of chemical-kinetic problems related to phenomena occurring behind a shock wave surrounding an object flying in the earth atmosphere are discussed, including the nonequilibrium thermochemical relaxation phenomena occurring behind a shock wave surrounding the flying object, problems related to aerobraking maneuver, the radiation phenomena for shock velocities of up to 12 km/sec, and the determination of rate coefficients for ionization reactions and associated electron-impact ionization reactions. Results of experiments are presented in form of graphs and tables, giving data on the reaction rate coefficients for air, the ionization distances, thermodynamic properties behind a shock wave, radiative heat flux calculations, Damkoehler numbers for the ablation-product layer, together with conclusions.

Description: Computations were made for those test cases of Problem 3 which were designated as laminar flows, viz., test cases 3.1, 3.2, 3.4, and 3.5. These test cases corresponded to flows over a flat plate and a compression ramp at high Mach number and at high Reynolds number. The computations over the compression ramps indicate a substantial streamwise extent of separation. Based on previous experience with separated laminar flows at high Mach numbers which indicated a substantial effect with spatial grid refinement, a series of computations with different grid sizes were performed. Also, for the flat plate, comparisons of the results for two different algorithms were made.

Description: A development status evaluation is presented for CFD methods applicable to fuselage-integrated scramjet powerplant incorporating hypersonic vehicles; these methods are critically important due to the unavailability of experimental facilities for such elevated Mach number/high-enthalphy conditions. Advancements are required in algorithm robustness and speed, geometric flexibility, and the inclusion of more complete flow physics. The most serious deficiencies lie in turbulence modeling, the lack of complete transition-prediction methods, and combustion modeling.

Description: An overview is given of research activity on the application of computational fluid dynamics (CDF) for hypersonic propulsion systems. After the initial consideration of the highly integrated nature of air-breathing hypersonic engines and airframe, attention is directed toward computations carried out for the components of the engine. A generic inlet configuration is considered in order to demonstrate the highly three dimensional viscous flow behavior occurring within rectangular inlets. Reacting flow computations for simple jet injection as well as for more complex combustion chambers are then discussed in order to show the capability of viscous finite rate chemical reaction computer simulations. Finally, the nozzle flow fields are demonstrated, showing the existence of complex shear layers and shock structure in the exhaust plume. The general issues associated with code validation as well as the specific issue associated with the use of CFD for design are discussed. A prognosis for the success of CFD in the design of future propulsion systems is offered.

Description: This is an effort aimed at validating recent hover prediction methods. The experimental basis for this validation work is an extensive set of loads, wake and performance data, which were obtained from a pressure instrumented model UH-60 rotor tested at the Sikorsky hover test facility and at Duits-Nederlandse Windtunnel (DNW). This model was equipped with replaceable tips - including a tapered and a BERP-type tip - which permitted studies of the effects of rotor geometry. The central prediction method studied is a free-wake, vortex embedded, full-potential CFD method - called HELIX-I. It is found that the HELIX-I code produces very good comparisons with the data including wake, surface pressure and performance. Comparisons with the measured radial load distributions have permitted an improved understanding of the wake resolution modelling requirements of CFD methods. Since HELIX-I is a combined Eulerian/Lagrangian method, limited comparisons are also made with a Lagrangian boundary element code (called EHPIC) and an Eulerian Navier-Stokes code (called TURNS). In most cases all methods produce good comparisons with the data. It is found that the HELIX-I code provides a good compromise between the speed of boundary integral methods and the comprehensive nature of Navier-Stokes methods.

Description: Shadowgraph flow visualization images were acquired from a 0.184-scale tiltrotor and wing in hover. Measurements and details of the vortex core structure were examined as a function of thrust condition and wake age. Experimental data for the isolated rotor wake geometry and rotor wake interactions with a semi-span wing and image plane were acquired. Quantitative measurements and comparisons of wake geometry and distortion were made for three configurations: the isolated rotor, rotor/wing, and rotor/wing/image plane. Comparisons between tiltrotor and helicopter rotor wake geometry measurements were made. Experimental wake geometry data were also compared with two wake models. Suggestions for improvements to existing prescribed-wake and free-wake models are proposed.

Description: An experimental investigation was conducted in the 14 by 22 ft subsonic tunnel at NASA Langley Research Center to quantify the rotor wake behind a scale model helicopter rotor in forward flight (mu = 0.15 and 0.23) at one thrust level (C sub T = 0.0064). The rotor system used in the present test consisted of a four-bladed, fully articulated hub and utilized blades of rectangular planform with a NACA-0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the flow in planes parallel and perpendicular to the freestream flow. Quantitative measurements of vortex location, vertical skew angle, and vortex particle void radius were obtained for vortices in the flow; convective velocities were obtained for blade tip vortices. Comparisons were made between the experimental results and the wake geometry generated by computational predictions. The results of these comparisons show that the interaction between wake vortex structures is an important consideration for correctly predicting the wake geometry.

Description: The flow field for a rotor blade in hover was computed by numerically solving the compressible thin-layer Navier-Stokes equations on embedded grids. In this work, three embedded grids were used to discretize the flow field - one for the rotor blade and two to convect the rotor wake. The computations were performed at two hovering test conditions, for a two-bladed rectangular rotor of aspect ratio six. The results compare fairly with experiment and illustrates the use of embedded grids in solving helicopter type flow fields.

Description: An unstructured-grid solver for the unsteady Euler equations has been developed for predicting the aerodynamics of helicopter rotor blades. This flow solver is a finite-volume scheme that computes flow quantities at the vertices of the mesh. Special treatments are used for the flux differencing and boundary conditions in order to compute rotary-wing flowfields, and these are detailed in the paper. The unstructured-grid solver permits adaptive grid refinement in order to improve the resolution of flow features such as shocks, rotor wakes and acoustic waves. These capabilities are demonstrated in the paper. Example calculations are presented for two hovering rotors. In both cases, adaptive-grid refinement is used to resolve high gradients near the rotor surface and also to capture the vortical regions in the rotor wake. The computed results show good agreement with experimental results for surface airloads and wake geometry.

Description: The development of implicit upwind algorithms for the solution of the three-dimensional, time-dependent Euler equations on unstructured tetrahedral meshes is described. The implicit temporal discretization involves either a two-sweep Gauss-Seide relaxation procedure, a two-sweep Point-Jacobi relaxation procedure, or a single-sweep Point-Implicit procedure; the upwind spatial discretization is based on the flux-difference splitting of Roe. Detailed descriptions of the three implicit solution algorithms are given, and calculations for the Boeing 747 transport configuration are presented to demonstrate the algorithms. Advantages and disadvantages of the implicit algorithms are discussed. A steady-state solution for the 747 configuration, obtained at transonic flow conditions using a mesh of over 100,000 cells, required less than one hour of CPU time on a Cray-2 computer, thus demonstrating the speed and robustness of the general capability.

Description: Two-dimensional CFD analyses are presented related to the ground testing of hypersonic, air-breathing models which feature scramjet exhaust flow simulation. CFD analysis indicates that it is possible to test aftbody powered hypersonic airbreather configurations in a static, pumped-down environment to obtain aftbody aerodynamic performance data.

Description: The Program for Solving the General-Frequency Unsteady Two-Dimensional Transonic Small-Disturbance Equation, XTRAN2L, is used to calculate time-accurate, finite-difference solutions of the nonlinear, small-disturbance potential equation for two- dimensional transonic flow about airfoils. The code can treat forced harmonic, pulse, or aeroelastic transient type motions. XTRAN2L uses a transonic small-disturbance equation that incorporates a time accurate finite-difference scheme. Airfoil flow tangency boundary conditions are defined to include airfoil contour, chord deformation, nondimensional plunge displacement, pitch, and trailing edge control surface deflection. Forced harmonic motion can be based on: 1) coefficients of harmonics based on information from each quarter period of the last cycle of harmonic motion; or 2) Fourier analyses of the last cycle of motion. Pulse motion (an alternate to forced harmonic motion) in which the airfoil is given a small prescribed pulse in a given mode of motion, and the aerodynamic transients are calculated. An aeroelastic transient capability is available within XTRAN2L, wherein the structural equations of motion are coupled with the aerodynamic solution procedure for simultaneous time-integration. The wake is represented as a slit downstream of the airfoil trailing edge. XTRAN2L includes nonreflecting farfield boundary conditions. XTRAN2L was developed on a CDC CYBER mainframe running under NOS 2.4. It is written in FORTRAN 5 and uses overlays to minimize storage requirements. The program requires 120K of memory in overlayed form. XTRAN2L was developed in 1987.

Description: The NASCRIN program was developed for analyzing two-dimensional flow fields in supersonic combustion ramjet (scramjet) inlets. NASCRIN solves the two-dimensional Euler or Navier-Stokes equations in conservative form by an unsplit, explicit, two-step finite-difference method. A more recent explicit-implicit, two-step scheme has also been incorporated in the code for viscous flow analysis. An algebraic, two-layer eddy-viscosity model is used for the turbulent flow calculations. NASCRIN can analyze both inviscid and viscous flows with no struts, one strut, or multiple struts embedded in the flow field. NASCRIN can be used in a quasi-three-dimensional sense for some scramjet inlets under certain simplifying assumptions. Although developed for supersonic internal flow, NASCRIN may be adapted to a variety of other flow problems. In particular, it should be readily adaptable to subsonic inflow with supersonic outflow, supersonic inflow with subsonic outflow, or fully subsonic flow. The NASCRIN program is available for batch execution on the CDC CYBER 203. The vectorized FORTRAN version was developed in 1983. NASCRIN has a central memory requirement of approximately 300K words for a grid size of about 3,000 points.

Description: The problem of axisymmetric transonic flow is of interest not only because of the practical application to missile and launch vehicle aerodynamics, but also because of its relation to fully three-dimensional flow in terms of the area rule. The RAXBOD computer program was developed for the analysis of steady, inviscid, irrotational, transonic flow over axisymmetric bodies in free air. RAXBOD uses a finite-difference relaxation method to numerically solve the exact formulation of the disturbance velocity potential with exact surface boundary conditions. Agreement with available experimental results has been good in cases where viscous effects and wind-tunnel wall interference are not important. The governing second-order partial differential equation describing the flow potential is replaced by a system of finite difference equations, including Jameson's "rotated" difference scheme at supersonic points. A stretching is applied to both the normal and tangential coordinates such that the infinite physical space is mapped onto a finite computational space. The boundary condition at infinity can be applied directly and there is no need for an asymptotic far-field solution. The system of finite difference equations is solved by a column relaxation method. In order to obtain both rapid convergence and any desired resolution, the relaxation is performed iteratively on successively refined grids. Input to RAXBOD consists of a description of the body geometry, the free stream conditions, and the desired resolution control parameters. Output from RAXBOD includes computed geometric parameters in the normal and tangential directions, iteration history information, drag coefficients, flow field data in the computational plane, and coordinates of the sonic line. This program is written in FORTRAN IV for batch execution and has been implemented on a CDC 6600 computer with an overlayed central memory requirement of approximately 40K (octal) of 60 bit words. Optional plotted output can be generated for the Calcomp plotting system. The RAXBOD program was developed in 1976.

Description: Two separate and distinct theories are incorporated in this computer program to estimate the lift-induced pressures existent on a wing-body combination. These are (1) the second-order shock-expansion theory, which is used to obtain the lifting pressures on the body alone at small angles of attack, and (2) the linear-theory integral equations, which is used to evaluate the lifting pressures induced by the wing. These equations relate the local surface slope at a point on the lifting surface to the pressure differential at the point and the influence of the pressures upstream of the point. The numerical solution of these equations is effected by treating the wing-planform as a composite of elemental rectangles and applying summation techniques to satisfy the necessary integral relations. Most of the input required by this program is involved with the description of the missile planform geometry. The output consists of the computed value of the lifting pressure slope (the differential pressure coefficient per degree angle of attack) for each of the elements in the planform array. A force and moment summary is presented for the configuration under consideration.

Description: A modified strip analysis has been developed for rapidly predicting flutter of finite-span, swept or unswept wings at subsonic to hypersonic speeds. The method employs distributions of aerodynamic parameters which may be evaluated from any suitable linear or nonlinear steady-flow theory or from measured steady-flow load distributions for the underformed wing. The method has been shown to give good flutter results for a broad range of wings at Mach number from 0 to as high as 15.3. The principles of the modified strip analysis may be summarized as follows: Variable section lift-curve slope and aerodynamic center are substituted respectively, for the two-dimensional incompressible-flow values of 2 pi and quarter chord which were employed by Barmby, Cunningham, and Garrick. Spanwise distributions of these steady-flow section aerodynamic parameters, which are pertinent to the desired planform and Mach number, are used. Appropriate values of Mach number-dependent circulation functions are obtained from two-dimensional unsteady compressible-flow theory. Use of the modified strip analysis avoids the necessity of reevaluating a number of loading parameters for each value of reduced frequency, since only the modified circulation functions, and of course the reduced frequency itself, vary with frequency. It is therefore practical to include in the digital computing program a very brief logical subroutine, which automatically selects reduced-frequency values that converge on a flutter solution. The problem of guessing suitable reduced-frequency values is thus eliminated, so that a large number of flutter points can be completely determined in a single brief run on the computing machine. If necessary, it is also practical to perform the calculations manually. Flutter characteristics have been calculated by the modified strip analysis and compared with results of other calculations and with experiments for Mach numbers up to 15.3 and for wings with sweep angles from 0 degrees to 52.5 degrees, aspect ratios from 2.0 to 7.4, taper ratios from 0.2 to 1.0, and center-of-gravity positions between 34% chord and 59% chord. These ranges probably cover the great majority of wings that are of practical interest with the exception of very low-aspect-ratio surfaces such as delta wings and missile fins. This program has been implemented on the IBM 7094.

Description: Experimental studies have been conducted to assess Reynolds and Mach number effects on a supercritical multielement airfoil. The airfoil is representative of the stall-critical station of an advanced transport wing design. The experimental work was conducted as part of a cooperative program between the Douglas Aircraft Company and the NASA Langley Research Center to improve current knowledge of high-lift flows and to develop a validation data base with practical geometries/conditions for emerging computational methods. This article describes results obtained for both landing and takeoff multielement airfoils (four- and three-element configurations) for a variety of Mach/Reynolds number combinations up to flight conditions. Effects on maximum lift are considered for the landing configurations, and effects on both lift and drag are reported for the takeoff geometry. The present test results revealed considerable maximum lift effects on the three-element landing configuration for Reynolds number variations, and significant Mach number effects on the four-element airfoil.

Description: This paper presents an alternate approach for the generation of volumetric grids for supersonic and hypersonic flows about complex configurations. The method uses parametric two-dimensional block-face grid definitions, within the framework of GRIDGEN2D. The incorporation of a face decomposition reduces complex surfaces to simple shapes. These simple shapes are recombined to obtain the final face definition. The advantages of this method include the reduction of overall grid generation time through the use of vectorized computer code, the elimination of generating matching block faces, and simplified boundary conditions.

Description: An algorithm is described that calculates inviscid, laminar, and turbulent flows on triangular meshes with an upwind discretization. A brief description of the base solver and the multigrid implementation is given, followed by results that consist mainly of convergence rates for inviscid and viscous flows over a NACA four-digit airfoil section. The results show that multigrid does accelerate convergence when the same relaxation parameters that yield good single-grid performance are used; however, larger gains in performance can be realized by doing less work in the relaxation scheme.

Description: The SUBAERF2 program was developed to provide for the aerodynamic analysis and design of low speed wing flap systems. SUBAERF2 is based on a linearized theory lifting surface solution. It is particularly well suited to configurations which, because of high speed flight requirements, must employ thin wings with highly swept leading edges. The program is applicable to wings with either sharp or rounded leading edges. This program is a new and improved version of LAR-13116 and LAR-12987, which it replaces. The low speed aerodynamic analysis method used in SUBAERF2 provides estimates of wing performance which include the effects of attainable leading-edge thrust and vortex lift. This basic aerodynamic analysis method has been improved to provide for the convenient, efficient and accurate treatment of simple leading-edge and trailing-edge flap systems. The user inputs flap geometry directly. Solutions can be found for various combinations of leading and trailing edge flap deflections. The program provides for the simultaneous analysis of up to 25 pairs of leading-edge and trailing-edge flap deflection schedules. A revised attainable thrust algorithm improves accuracy at the low Mach numbers sometimes encountered in wind tunnel testing. Also added is a means of estimating the distribution of leading edge separation vortex forces. The revised program has been particularly useful in the subsonic analysis of vehicles designed for supersonic cruise. The SUBAERF2 program is written in FORTRAN V for batch execution and has been implemented on a CDC 175 computer operating under NOS 2.4 with a central memory requirement of approximately 115K (octal) of 60 bit words. This program was originally developed in 1983 and later revised in 1988.

Description: WAVDRAG calculates the supersonic zero-lift wave drag of complex aircraft configurations. The numerical model of an aircraft is used throughout the design process from concept to manufacturing. WAVDRAG incorporates extended geometric input capabilities to permit use of a more accurate mathematical model. With WAVDRAG, the engineer can define aircraft components as fusiform or nonfusiform in terms of non-intersecting contours in any direction or more traditional parallel contours. In addition, laterally asymmetric configurations can be simulated. The calculations in WAVDRAG are based on Whitcomb's area-rule computation of equivalent-bodies, with modifications for supersonic speed. Instead of using a single equivalent-body, WAVDRAG calculates a series of equivalent-bodies, one for each roll angle. The total aircraft configuration wave drag is the integrated average of the equivalent-body wave drags through the full roll range of 360 degrees. WAVDRAG currently accepts up to 30 user-defined components containing a maximum of 50 contours as geometric input. Each contour contains a maximum of 50 points. The Mach number, angle-of-attack, and coordinates of angle-of-attack rotation are also input. The program warns of any fusiform-body line segments having a slope larger than the Mach angle. WAVDRAG calculates total drag and the wave-drag coefficient of the specified aircraft configuration. WAVDRAG is written in FORTRAN 77 for batch execution and has been implemented on a CDC CYBER 170 series computer with a central memory requirement of approximately 63K (octal) of 60 bit words. This program was developed in 1983.

Description: An approximate inverse solution is presented for the nonequilibrium flow in the inviscid shock layer about a vehicle in hypersonic flight. The method is based upon a thin-shock-layer approximation and has the advantage of being applicable to both subsonic and supersonic regions of the shock layer. The relative simplicity of the method makes it ideally suited for programming on a digital computer with a significant reduction in storage capacity and computing time required by other more exact methods. Comparison of nonequilibrium solutions for an air mixture obtained by the present method is made with solutions obtained by two other methods. Additional cases are presented for entry of spherical nose cones into representative Venusian and Matrian atmospheres. A digital computer program written in FORTRAN language is presented that permits an arbitrary gas mixture to be employed in the solution. The effects of vibration, dissociation, recombination, electronic excitation, and ionization are included in the program.

Description: Small areas of high heat transfer and pressure can occur on a vehicle surface due to the influence of an impinging shock on the local flow. A method was needed to determine peak pressure and heating of these areas. This package is a system of computer programs designed to calculate two-dimensional shock interference patterns for six types of interference flows. Results also include properties of the inviscid flow field and the inviscid-viscous interaction at the surface along with peak pressure and peak heating at the impingement point. The six types of interference flow patterns considered are: 1) Type I interference patterns, occurring when two weak shocks of opposite families, BS (bow shock) and IS (impingment shock), intersect when the flow upstream of the impingement point is supersonic, or in the case of a blunt body, takes place well below the sonic point. 2) Type II interference pattern occurs when two shocks of opposite families (bow shock and impinging shock) intersect. Both shocks are weak as in type I, but are of such strength that in order to turn the flow, a Mach reflection must exist in the center of the flow field with an embedded subsonic region occurring between the intersection points (A & B) and the accompanying shear layers. Type II interference occurs on a blunt body when the impinging shock intersects the bow shock near the sonic point. 3) Type III shock interference pattern occurs when a weak impinging shock intersects a strong detached bow shock. On a blunt body the shock intersection occurs near or above the lower sonic point. 4) Type IV interference can occur when the impinging shock intersects a strong bow shock ahead of a subsonic flow region. On a blunt body this shock intersection is located between the lower sonic point and just above the body axis. The impinging shock causes a displacement of the bow shock and the formation of a supersonic jet that is embedded in the subsonic region. A jet bow shock is produced when the jet impinges on the surface, creating a small region with high stagnation heating. 5) Type V interference involves the interaction of two weak shocks of the same family. The interaction produces a shear layer, a supersonic jet, and a transmitted impinging shock. On a blunt body the shock interaction occurs near the upper sonic point. 6) Type VI interference involves the intersection of two weak shocks of the same family, which leads to an entirely supersonic flow field. This type of interference is important because it provides a means for predicting the onset of type V. Peak-heating correlations for laminar and turbulent shock-boundary-layer interactions are included in the programs for types I, II, V, and VI interference patterns. Heating correlations for laminar and turbulent reattaching shear layers obtained from separation studies are included in the program for type III interference. This program is written in FORTRAN IV for batch execution and has been implemented on a CDC 6000 Series computer. This program was developed in 1973.

Description: A computer program has been written to obtain the wave and friction drag of configurations with bodies of revolution and fins. These inviscid flow fields are superimposed and the wave drag of the configuration is obtained by integration of the surface pressures. The friction drag is obtained from the viscous flow field of the body and a flat-plate friction analysis of the fins. The numerical solution of these flow fields, superposition, and integration to obtain total drag have been programmed for high-speed digital computation. A large portion of the input required by the program is involved with the description of the configuration geometry and the specific surface positions where pressures are to be evaluated. In addition to drag forces, an output is available whereby the pressure distributions on the body and fins can be obtained.

Description: The interaction of a turbulent boundary layer with rarefaction and shock waves in flows past inclined steps was investigated experimentally and theoretically. The experiments were carried out in supersonic wind tunnels with test sections of 0.6 x 0.6 m and 0.2 x 0.2 m, with adiabatic conditions on the surface model. Based on detailed measurements of pressure fields, velocity, and surface friction, combined with results of optical visualization and analysis of limiting flow lines, three characteristic flow regimes are identified. These are (1) nonseparated flow at small step angles, (2) formation of a local separation zone with a free separation point at moderate step angles, and (3) formation of a large-scale separated flow with a fixed separation point at sufficiently large step angles. The quantitative gasdynamic schemes and surface pressure distributions for these flow regimes are shown for Mach 2.85.

Description: An account is given of experimental and computational results on the mixing of single, double, and opposed rows of jets characterized by an either isothermal or variable temperature mainstream in a confined subsonic crossflow; these flow configurations are typical of gas turbine combustor dilution chambers. It is established that the momentum-flux ratio is the most significant flow variable. Combinations of flow and geometry yielding optimum mixing were identified from experimental and computational results. The orifice spacing and momentum-flux relationships affected jet structure, which was significantly different between jets injected from the inner wall of a turn and those injected from the outer wall.

Description: The essential elements of a computational fluid dynamics analysis of the HL-20/personnel launch system aerothermal environment at hypersonic speeds including surface definition, grid generation, solution techniques, and visual representation of results are presented. Examples of solution technique validation through comparison with data from ground-based facilities are presented, along with results from computations at flight conditions. Computations at flight points indicate that real-gas effects have little or no effect on vehicle aerodynamics and, at these conditions, results from approximate techniques for determining surface heating are comparable with those obtained from Navier-Stokes solutions.

Description: Definition of the aerothermal environment is critical to any vehicle such as the HL-20 Personnel Launch System that operates within the hypersonic flight regime. Selection of an appropriate thermal protection system design is highly dependent on the accuracy of the heating-environment prediction. It is demonstrated that the entry environment determines the thermal protection system design for this vehicle. The methods used to predict the thermal environment for the HL-20 Personnel Launch System vehicle are described. Comparisons of the engineering solutions with computational fluid dynamic predictions, as well as wind-tunnel test results, show good agreement. The aeroheating predictions over several critical regions of the vehicle, including the stagnation areas of the nose and leading edges, windward centerline and wing surfaces, and leeward surfaces, are discussed. Results of predictions based on the engineering methods found within the MINIVER aerodynamic heating code are used in conjunction with the results of the extensive wind-tunnel tests on this configuration to define a flight thermal environment. Finally, the selection of the thermal protection system based on these predictions and current technology is described.

Description: Experiments were conducted to observe the cross-sectional structure and streamwise growth of round transverse liquid jets injected into a highly accelerated boundary layer in supersonic flow. The accompanying shock structure was also visualized. In one case, a round jet of acetone was injected into a fully turbulent Mach 2.5 boundary layer that was subsequently accelerated and partially laminarized through a sharp Prandtl-Meyer expansion corner. In the second case, a jet was injected into the laminarized Mach 3.2 boundary layer downstream of the expansion corner at the same jet-to-freestream momentum ratio. The jet and shock structure in both cases were visualized using schlieren optics. Wall-flow patterns were visualized using paints. It was found that the lateral spreading of jets injected downstream of the expansion fan was augmented close to the wall and had a cross-sectional structure significantly different from that of the jet injected upstream: the upstream jet spreads rapidly at the expansion corner in both the lateral and vertical directions.

Description: Computational results are presented to illustrate the powered aftbody effects of representing the scramjet inlet on a generic hypersonic vehicle with a fairing, to divert the external flow, as compared to an operating flow-through scramjet inlet. This study is pertinent to the ground testing of hypersonic, airbreathing models employing scramjet exhaust flow simulation in typical small-scale hypersonic wind tunnels. The comparison of aftbody effects due to inlet representation is well-suited for computational study, since small model size typically precludes the ability to ingest flow into the inlet and perform exhaust simulation at the same time. Two-dimensional analysis indicates that, although flowfield differences exist for the two types of inlet representations, little, if any, difference in surface aftbody characteristics is caused by fairing over the inlet.