ALBERT

Description: The thinning and intensification of the cross tail current sheet during the substorm growth phase are analyzed during the CDAW 6 substorm (22 Mar. 1979) using two complementary methods. The magnetic field and current sheet development are determined using data from two spacecraft and a global magnetic field model with several free parameters. These results are compared with the local calculation of the current sheet location and structure previously done by McPherron et al. Both methods lead to the conclusion that an extremely thin current sheet existed prior to the substorm onset, and the thicknesses estimated by the two methods at substorm onset agree relatively well. The plasma data from the ISEE 1 spacecraft at 13 R(sub E) show an anisotropy in the low energy electrons during the growth phase which disappears just before the substorm onset. The global magnetic model results suggest that the field is sufficiently stretched to scatter such low energy electrons. The strong stretching may improve the conditions for the growth of the ion tearing instability in the near Earth tail at substorm onset.

Description: An approach to the study of the solar wind-magnetosphere interaction by signal type, that is, by examining the effect in the magnetosphere of well defined interplanetary structures, is presented. Focus is on the response of the magnetosphere to interplanetary magnetic clouds. Among their properties are: the slow and smooth variation of the magnetic field vector, with fluctuation level well below common interplanetary values; the similarly well behaved bulk flow; the wide range of field and flow parameters; and the longevity of passage (1 to 2 days). If the magnetic cloud is oriented such that a long period of uninterruptedly northward pointing field is followed by a long interval of continuously southward pointing field, then the transition of the magnetosphere from a quiescent state (the 'ground state') to a very active state can be studied, the latter being sustained by continued forcing from the magnetic cloud. A synopsis of the main findings of a recent study in such an interaction is given, concentrating on the substorm activity attending the second part of cloud passage.

Description: The stability of the geomagnetic tail is investigated on the basis of three dimensional resistive magnetohydrodynamic simulations, using different dynamic constraints and different initial equilibria. Different forms of the energy equation for isotropic pressure are found to have no significant effect on the dynamic growth of a resistive tearing instability, which is responsible for near Earth reconnection, plasmoid formation and ejection, and the generation of fast plasma flows. The constraints of a modified double adiabatic approach, however, can quench the tearing instability through the development of large, mirror type, anisotropies in the boundary regions of the plasma sheet, unless isotropization occurs on fast, nearly Alfvenic, time scales. The presence of a net cross tail magnetic field component B(sub yN) can reduce the growth of the instability without complete stabilization. An increase of B(sub z) from midnight toward the tail flanks, however, by more than a factor of about 3, apparently completely stabilizes the tearing mode. Stabilization and destabilization thus may depend on properties and constraints (and their release) in regions other than the neutral sheet where reconnection is initiated.

Description: Issues concerning the 'driven' versus 'unloading' nature of substorms are presented. The original concepts attendant to this debate are presented and substorms are concluded to inextricably combine aspects that are driven with aspects that represent a loading-unloading system. For isolated substorms, the magnetosphere-ionosphere system is shown to exhibit a bimodal response to solar wind changes. A 20 min response characteristic is associated with the driven aspect of substorms, while a 1 hr response time is associated with unloading. It is found that for strong solar wind input conditions, the magnetospheric response becomes more nearly unimodal. This is interpreted in terms of a nonlinear dynamical evolution of the system. Simple analog models are described which capture the essence of the nonlinear magnetospheric behavior. These models exhibit chaotic transitions for strong driving conditions: this may explain the observed behavior of the magnetosphere during strong geomagnetic activity.

Description: A pseudobreakup is a phenomenon similar to the substorm expansive phase onset, including an activation of an auroral arc, a burst of Pi2 micropulsations, and enhancement of the westward electrojet. However, these effects are weak and a pseudobreak is generally assumed to be very localized. The pseudobreakups are discussed based on simultaneous observations made in space and on the ground during the substorm growth phase. In the events studied the main features listed above are found, but the significance of the localization is unclear. The optical pseudobreakup, with associated magnetic perturbations, is highly localized, but simultaneously a wide local time sector of the auroral oval may be activated. The major differences between pseudobreakups and substorm expansive phase onsets are concluded to be the intensity and the development that follows. Careful study of pseudobreakups may help to determine phase initiation, and the role of the ionosphere-magnetosphere coupling in the substorm process.

Description: A 54.95-MHz coherent backscatter radar, an ionosonde and the magnetometer located at Trivandrum in India (8.5 deg N, 77 deg E, 0.5 deg N dip angle) recorded large-amplitude ionospheric fluctuations and magnetic field fluctuations associated with a Pc5 micropulsation event, which occurred during an intense magnetic storm on 24 March 1991 (A(sub p) = 161). Simultaneous 100-n T-level fluctuations are also observed in the H-component at Brorfelde, Denmark (55.6 deg N gm) and at Narsarsuaq, Greenland (70.6 deg N gm). Our study of the above observations shows that the E-W electric field fluctuations in the E- and F-regions and the magnetic field fluctuations at Thumba are dominated by a near-sinusoidal oscillation of 10 min during 1730-1900 IST (1200-1330 UT), the amplitude of the electric field oscillation in the equatorial electrojet (EEJ) is 0.1-0.25 mV/m and it increases with height, while it is about 1.0 mV/m in the F-region, the ground-level H-component oscillation can be accounted for by the ionospheric current oscillation generated by the observed electric field oscillation in the EEJ and the H-component oscillations at Trivandrum and Brofelde are in phase with each other. The observations are interpreted in terms of a compressional cavity mode resonance in the inner magnetosphere and the assoicated ionospheric electric field penetrating from high latitudes to the magnetic equator.

Description: The Coast Ranges of the Cascadia margin are overriding the subducted Juan de Fuca/Gorda plate. We investigate the extent to which the latitudinal change in attributes related to the subduction process. These attributes include the varibale age of the subducted slab that underlies the Coast Ranges and average vertical crustal velocities of the western margin of the Coast Rnages for two markedly different time periods, the last 45 years and the last 100 kyr. These vertical crustal velocities are computed from the resurveying of highway bech marks and from the present elevation of shore platforms that have been uplifted in the late Quaternary, respectively. Topogarphy of the Coast Ranges is in part a function of the age and bouyancy of the underlying subducted plate. This is evident in the fact that the two highest topographic elements of the Coast Rnages, the Klamath Mountains and the Olympic Mountains, are underlain by youngest subducted oceanic crust. The subducted Blanco Fracture Zone in southernmost Oregon is responsible for an age discontinuity of subducted crust under the Klamath Mountains. The norhtern terminus of hte topographically higher Klamaths is offset to the north relative to the position of the underlying Blanco Fracture Zone, teh offset being in the direction of migration of the farcture zone, as dictated by relative plate motions. Vertical crustal velocities at the coast, derived from becnh mark surveys, are as much as an order of magnitude greater than vertical crustal velocities derived from uplifted shore platforms. This uplift rate discrepancy indicates that strain is accumulating on the plate margin, to be released during the next interplate earthquake. In a latitudinal sense, average Coast Rnage topography is relatively high where bench mark-derived, short-term vertical crustal velocities are highest. Becuase the shore platform vertical crustal velocities reflect longer-term, premanent uplift, we infer that a small percentage of the interseismic strain that accumulates as rapid short-term uplift is not recovered by subduction earthquakes but rather contributes to rock uplift of the Coast Ranges. The conjecture that permanent rock uplift is related to interseismic uplift is consistent with the observation that those segments of the subduction zone subject to greater interseismic uplift rates are at approximately the same latitudes as those segments of the Coast Ranges that have higher magnitudes of rock uplift over the long term.

Description: A comprehensive review is presented of the mathematical models used to represent magnetic fields in the Earth's magnetosphere, of the way existing data-based models use these methods and of the associated problems and concepts. The magnetic field has five main components: the internal field, the magnetopause, the ring current, the tail and Birkeland currents. Methods of representing separately each of these are discussed, as is the deformation of magnetic fields; Appendix B traces the connection between deformations and the Cauchy integral. A summary section lists the uses of data-based models and their likely future evolution, and Appendix A supplements the text with a set of problems.

Description: We present a map of the coseimic displacement field resulting from the Landers, California, June 28, 1992, earthquake derived using data acquired from an orbiting high-resolution radar system. We achieve results more accurate than previous space studies and similar in accuracy to those obtained by conventional field survey techniques. Data from the ERS 1 synthetic aperture radar instrument acquired in April, July, and August 1992 are used to generate a high-resolution, wide area map of the displacements. The data represent the motion in the direction of the radar line of sight to centimeter level precision of each 30-m resolution element in a 113 km by 90 km image. Our coseismic displacement contour map gives a lobed pattern consistent with theoretical models of the displacement field from the earthquake. Fine structure observed as displacement tiling in regions several kilometers from the fault appears to be the result of local surface fracturing. Comparison of these data with Global Positioning System and electronic distance measurement survey data yield a correlation of 0.96; thus the radar measurements are a means to extend the point measurements acquired by traditional techniques to an area map format. The technique we use is (1) more automatic, (2) more precise, and (3) better validated than previous similar applications of differential radar interferometry. Since we require only remotely sensed satellite data with no additioanl requirements for ancillary information. the technique is well suited for global seismic monitoring and analysis.

Description: A search was conducted for the signatures of Birkeland currents in the Earth's magnetic tail, using observed values of B(sub x) and B(sub y) from large sets of spacecraft data. The data were binned by x and y for -10 greater than x(sub GSM) greater than -35 and absolute value of y(sub GSM) less than or equal to 20 R(sub E) (less than or equal to 30 R(sub E) for x(sub GSM) less than or equal to -25 R(sub E)) and in each bin their distribution in the (B(sub x), B(sub y)) plane was fitted by least squares to a piecewise linear function. That gave average x-y distributions of the flaring angle between B(sub xy) and the x direction, as well as that angle's variation across the thickness of the plasma sheet. Angles obtained in the central plasma sheet differed from those derived near the lobe boundary. That is the expected signature if earthward or tailward Birkeland current sheets are embedded in the plasma sheet, and from this dfiference we derived the dawn-dusk profiles of the tail Birkeland currents for several x(sub GSM) intervals. It was found that (1) the Birkeland currents have the sense of region 1 currents, when mapped to the ionosphere; (2) both the linear current density (kiloamperes/R(sub E)) and the net magnitude of the field-aligned currents decrease rapidly down the tail; (3) the total Birkeland current at x approximately equals -10 R(sub E) equals approximately equals 500-700 kA, which is approx. 30% of the net region 1 current observed at ionospheric altitudes, in agreement with model mapping results; and (4) the B(sub z) and B(sub y) components of the interplanetary magnetic field influence the distribution of Birkeland currents in the tail.

Description: The compressible dynamic stall flowfield over a NACA 0012 airfoil transiently pitching from 0 to 60 deg at a constant rate under compressible flow conditions has been studied using real-time interferometry. A quantitative description of the overall flowfield, including the finer details of dynamic stall vortex formation, growth, and the concomitant changes in the airfoil pressure distribution, has been provided by analyzing the interferograms. For Mach numbers above 0.4, small multiple shocks appear near the leading edge and are present through the initial stages of dynamic stall. Dynamic stall was found to occur coincidentally with the bursting of the separation bubble over the airfoil. Compressibility was found to confine the dynamic stall vortical structure closer to the airfoil surface. The measurements show that the peak suction pressure coefficient drops with increasing freestream Mach number, and also it lags the steady flow values at any given angle of attack. As the dynamic stall vortex is shed, an anti-clockwise vortex is induced near the trailing edge, which actively interacts with the post-stall flow.

Description: The effect of the porous leading edge of an airfoil on the blade-vortex interaction noise, which dominates the far-field acoustic spectrum of the helicopter, is investigated. The thin-layer Navier-Stokes equations are solved with a high-order upwind-biased scheme and a multizonal grid system. The Baldwin-Lomax turbulence model is modified for considering transpiration on the surface. The amplitudes of the propagating acoustic wave in the near field are calculated directly from the computation. The porosity effect on the surface is modeled in two ways: (1) imposition of prescribed transpiration velocity distribution and (2) calculation of transpiration velocity distribution by Darcy's law. Results show leading-edge transpiration can suppress pressure fluctuations at the leading edge during blade-vortex interaction and consequently reduce the amplitude of propagating noise by 30% at a maximum in the near field.

Description: A method has been developed for calculating the viscous flow about airfoils with and without deflected flaps at -90 deg incidence. This method provides for the solution of the unsteady incompressible Navier-Stokes equations by means of an implicit technique. The solution is calculated on a body-fitted computational mesh using a staggered-grid method. The vorticity is defined at the node points, and the velocity components are defined at the mesh-cell sides. The staggered-grid orientation provides for accurate representation of vorticity at the node points and the continuity equation at the mesh-cell centers. The method provides for the noniterative solution of the flowfield and satisfies the continuity equation to machine zero at each time step. The method is evaluated in terms of its stability to predict two-dimensional flow about an airfoil at -90-deg incidence for varying Reynolds number and laminar/turbulent models. The variations of the average loading and surface pressure distribution due to flap deflection, Reynolds number, and laminar or turbulent flow are presented and compared with experimental results. The comparisom indicate that the calculated drag and drag reduction caused by flap deflection and the calculated average surface pressure are in excellent agreement with the measured results at a similar Reynolds number.

Description: New line parameters for two heavy odd nitrogen molecules HNO3 in the nu(sub 5)/2nu(sub 9) region, and ClONO2 in the nu(sub 4) region are incorporated in the analysis of high resolution i.r. atmospheric spectra. The line parameters are tested and renormalized vs laboratory spectra, and then applied to retrievals from balloon-borne and ground-based solar absorption spectra.

Description: The spectroscopic identification for the HNO3 3 nu(sub 9) - nu(sub 9) band Q branch at 830.4/cm is reported based on 0.01/cm resolution solar occultation spectra of the lower stratosphere recorded by the Atmospheric Trace Molecule Spectroscopy (ATMOS) Fourier transform spectrometer and a recent analysis of this band. Least-squares fits to 0.0025/cm resolution laboratory spectra in the Q branch region indicate an integrated intensity of 0.529 x 10(exp -18)/cm/mol/sq cm at 296 K for this weak band. Stratospheric HNO3 retrievals derived from the ATMOS data are consistent with this value within its estimated uncertainty of about +/- 30%. A set of spectroscopic line parameters suitable for atmospheric studies has been generated.

Description: About 200 i.r. solar spectra recorded at 0.01/cm resolution on 71 days between November 1991 and July 1993 at the Network for the Detection of Stratospheric Change (NDSC) station at Mauna Loa, Hawaii (latitude 19.53 deg N, longitude 155.58 deg W, elevation 3.459 km) have been analyzed with a nonlinear least-squares spectral fitting technique to study temporal variations in the total column of atmospheric ethane (C2H6) above the site. The results were derived from the analysis of the unresolved nu(sub 7) band (P)Q(sub 3) subbranch at 2976.8/cm. A distinct seasonal cycle is observed with a factor of 2 variation, a maximum total column of 1.16 x 10(exp 16) mol/sq cm at the end of winter, and a minimum total column of 0.53 x 10(exp 16) mol/sq cm at the end of summer. Our measurements are compared with previous observations and model predictions.

Description: Quantitative measurements of the wavelength dependence of aerosol extinction in the 750-3400/cm spectral region have been derived from 0.01/cm resolution stratospheric solar occultation spectra recorded by the ATMOS (Atmospheric Trace Molecule Spectroscopy) Fourier transform spectrometer about 9 1/2 months after the Mt Pinatubo volcanic eruption. Strong, broad aerosol features have been identified near 900, 1060, 1190, 1720, and 2900/cm below a tangent height of approximately 30 km. Aerosol extinction measurements derived from approximately 0.05/cm wide microwindows nearly free of telluric line absorption in the ATMOS spectra are compared with transmission calculations derived from aerosol size distribution profiles retrieved from correlative SAGE (Stratospheric Aerosol and Gas Experiment) II visible and near i.r. extinction measurements, seasonal and zonally averaged H2SO4 aerosol weight percentage profiles, and published sulfuric acid optical constants derived from room temperature laboratory measurements. The calculated shapes and positions of the aerosol features are generally consistent with the observations, thereby confirming that the aerosols are predominantly concentrated H2SO4-H2O droplets, but there are significant differences between the measured and calculated wavelength dependences of the aerosol extinction. We attribute these differences as primarily the result of errors in the calculated low temperature H2SO4-H2O optical constants. Errors in both the published room temperature optical constants and the limitations of the Lorentz-Lorenz relation are likely to be important.

Description: We present vertical column abundances of H2O, N2O, HNO3, NO2, O3, HF, HCl, and ClNO3, determined from solar absorption spectra measured by the JPL MkIV interferometer from the NASA DC-8 aircraft. These observations, taken in 1987 and 1992, covered latitudes ranging from 85 deg S to 85 deg N. Although most gases display latitude symmetry, large asymmetries in H2O, HNO3, and O3 are apparent, which can be ascribed to processes enhanced by the colder Antarctic winter temperatures.

Description: Simultaneous in situ measurements of NO2, NO, O3, ClO, pressure and temperature have been made for the first time, presenting a unique opportunity to test our current understanding of the photochemistry of the lower stratospere. Data were collected from several flights of the ER-2 aircraft at mid-latitudes in May 1993 during NASA's Stratospheric Photochemistry, Aerosols and Dynamics Expedition (SPADE). The daytime ratio of NO2/NO remains fairly constant at 19 km with a typical value of 0.68 and standard deviation of +/- 17. The ratio observations are compared with simple steady-state calculations based on laboratory-measured reaction rates and modeled NO2 photolysis rates. At each measurement point the daytime NO2/NO with its measurements uncertainty overlap the results of steady-state caculations and associated uncertainty. Possible sources of error are examined in both model and measurements. It is shown that more accurate laboratory determinations of the NO + 03 reaction rate and of the NO2 cross-sections in the 200-220 K temperature range characteristic of the lower stratosphere would allow for a more robust test of our knowledge of NO(X) phtochemistry by reducing significant sources if uncertainties in the interpretation of statospheric measurements.

Description: The ability to predict short-term variations in the Earth's rotation has gained importance in recent years owing to more precise spacecraft tracking requirements. Universal time (UT1), that component of the Earth's orientation corresponding to the rotation angle, can be measured by number of high-precision space geodetic techniques. A Kalman filter developed at the Jet Propulsion Laboratory (JPL) optimally combines these different data sets and generates a smoothed times series and a set of predictions for UT1, as well as for additional Earth orientation components. These UT1 predictions utilize an empirically derived random walk stochastic model for the length of the day (LOD) and require frequent and up-to-date measurements of either UT1 or LOD to keep errors from quickly accumulating. Recent studies have shown that LOD variations are correlated with changes in the Earth's axial atmospheric angular momentum (AAM) over timescales of several years down to as little as 8 days. AAM estimates and forecasts out to 10 days are routinely available from meteorological analysis centers; these data can supplement geodetic measurements to improve the short-term prediction of LOD and have therefore been incorporated as independent data types in the JPL Kalman filter. We find that AAM and, to a lesser extent, AAM forecast data are extremely helpful in generating accurate near-real-time estimates of UT1 and LOD and in improving short-term predictions of these quantities out to about 10 days.

Description: Rotor noise prediction codes predict the thickness and loading noise produced by a helicopter rotor, given the blade motion, rotor operating conditions, and fluctuating force distribution over the blade surface. However, the criticality of these various inputs, and their respective effects on the predicted acoustic field, have never been fully addressed. This paper examines the importance of these inputs, and the sensitivity of the acoustic predicitions to a variation of each parameter. The effects of collective and cyclic pitch, as well as coning and cyclic flapping, are presented. Blade loading inputs are examined to determine the necessary spatial and temporal resolution, as well as the importance of the chordwise distribution. The acoustic predictions show regions in the acoustic field where significant errors occur when simplified blade motions or blade loadings are used. An assessment of the variation in the predicted acoustic field is balanced by a consideration of Central Processing Unit (CPU) time necessary for the various approximations.

Description: Disk-shaped current distributions are useful tools in modeling the magnetospheres of Earth and other planets and have also been adapted for modeling the geotail. Such models usually start with an axisymmetric vector potential but may be modified to account for observed asymmetries, variable thickness, and warping in response to an inclined orientation of the planetary dipole axis. Models of this type until now either have lacked the ability to simulate a sharp inner edge of the current and to control accurately its falloff with distance or did not allow a simple analytical representation. Here existing methods will be reviewed, after which a new class of models which overcomes the above deficiencies and also allows the modeling of current disks of finite thickness flanked by current-free regions will be presented.

Description: An improved model of Earth's gravitational field, Goddard Earth Model T-3 (GEM-T3), has been developed from a combination of satellite tracking, satellite altimeter, and surface gravimetric data. GEM-T3 provides a significant improvement in the modeling of the gravity field at half wavelengths of 400 km and longer. This model, complete to degree and order 50, yields more accurate satellite orbits and an improved geoid representation than previous Goddard Earth Models. GEM-T3 uses altimeter data from GEOS 3 (1975-1976), Seasat (1978) and Geosat (1986-1987). Tracking information used in the solution includes more than 1300 arcs of data encompassing 31 different satellites. The recovery of the long-wavelength components of the solution relies mostly on highly precise satellite laser ranging (SLR) data, but also includes Tracking Network (TRANET) Doppler, optical, and satellite-to-satellite tracking acquired between the ATS 6 and GEOS 3 satellites. The main advances over GEM-T2 (beyond the inclusion of altimeter and surface gravity information which is essential for the resolution of the shorter wavelength geoid) are some improved tracking data analysis approaches and additional SLR data. Although the use of altimeter data has greatly enhanced the modeling of the ocean geoid between 65 deg N and 60 deg S latitudes in GEM-T3, the lack of accurate detailed surface gravimetry leaves poor geoid resolution over many continental regions of great tectonic interest (e.g., Himalayas, Andes). Estimates of polar motion, tracking station coordinates, and long-wavelength ocean tidal terms were also made (accounting for 6330 parameters). GEM-T3 has undergone error calibration using a technique based on subset solutions to produce reliable error estimates. The calibration is based on the condition that the expected mean square deviation of a subset gravity solution from the full set values is predicted by the solutions' error covariances. Data weights are iteratively adjusted until this condition for the error calibration is satisfied. In addition, gravity field tests were performed on strong satellite data sets withheld from the solution (thereby ensuring their independence). In these tests, the performance of the subset models on the withheld observations is compared to error projections based on their calibrated error covariances. These results demonstrate that orbit accuracy projections are reliable for new satellites which were not included in GEM-T3.

Description: We present predictions of the signatures of magnetosheath particle precipitation (in the regions classified as open low-latitude boundary layer, cusp, mantle and polar cap) for periods when the interplanetary magnetic field has a southward component. These are made using the 'pulsating cusp' model of the effects of time-varying magnetic reconnection at the dayside magnetopause. Predictions are made for both low-altitude satellites in the topside ionosphere and for midaltitude spacecraft in the magnetosphere. Low-altitude cusp signatures, which show a continuous ion dispersion signature, reveal 'quasi-steady reconnection' (one limit of the pulsating cusp model), which persists for a period of at least 10 min. We estimate that 'quasi-steady' in this context corresponds to fluctuations in the reconnection rate of a factor of 2 or less. The other limit of the pulsating cusp model explains the instantaneous jumps in the precipitating ion spectrum that have been observed at low altitudes. Such jumps are produced by isolated pulses of reconnection: that is, they are separated by intervals when the reconnection rate is zero. These also generate convecting patches on the magnetopause in which the field lines thread the boundary via a rotational discontinuity separated by more extensive regions of tangential discontinuity. Predictions of the corresponding ion precipitation signatures seen by midaltitude spacecraft are presented. We resolve the apparent contradiction between estimates of the width of the injection region from midaltitude data and the concept of continuous entry of solar wind plasma along open field lines. In addition, we reevaluate the use of pitch angle-energy dispersion to estimate the injection distance.

Description: Simultaneous profiles of aerosol backscatter ratio were measured over Lauder, New Zealand (45 deg S, 170 deg E) on the night of November 24, 1992. Instrumentation comprised two complementary lidar systems and a backscattersonde, to give measurements at wavelengths 351, 490, 532, and 940 nm. The data from the lidars and the backscattersonde were self-consistent, enabling the wavelength dependence of aerosol backscatter to be determined as a function of altitude. This wavelength-dependence is a useful parameter in radiative transfer calculations. In the stratosphere, the average wavelength exponent between 351 and 940 nm was -1.23 +/- 0.1, which was in good agreement with values derived from measured physical properties of aerosols.

Description: High-energy electrons have been measured systematically in a low-altitude (520 x 675 km), nearly polar (inclination = 82 deg) orbit by sensitive instruments onboard the Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX). Count rate channels with electron energy thresholds ranging from 0.4 MeV to 3.5 MeV in three different instruments have been used to examine relativistic electron variations as a function of L-shell parameter and time. A long run of essentially continuous data (July 1992 - July 1993) shows substantial acceleration of energetic electrons throughout much of the magnetosphere on rapid time scales. This acceleration appears to be due to solar wind velocity enhancements and is surprisingly large in that the radiation belt 'slot' region often is filled temporarily and electron fluxes are strongly enhanced even at very low L-values (L aprroximately 2). A superposed epoch analysis shows that electron fluxes rise rapidly for 2.5 is approximately less than L is approximately less than 5. These increases occur on a time scale of order 1-2 days and are most abrupt for L-values near 3. The temporal decay rate of the fluxes is dependent on energy and L-value and may be described by J = Ke-t/to with t(sub o) approximately equals 5-10 days. Thus, these results suggest that the Earth's magnetosphere is a cosmic electron accelerator of substantial strength and efficiency.

Description: The U.S. National Aeronautics and Space Administration (NASA) Balloon Program has been highly successful since recovering from the catastrophic balloon failure problems of the early to mid 1980s. Balloons have continued to perform at unprecedented success rates. The comprehensive research and development (R&D) effort has continued with advances being made across the spectrum of balloon related disciplines. The long duration balloon project will be transitioning from a development effort to an operational capability this year. Recently, emphasis has been placed on the development and implementation of new support systems and facilities. A new permanent launch facility at Fort Sumner, New Mexico has been established. New ground station support equipment is being implemented, and a new heavy load launch vehicle is scheduled to be implemented in 1992. The progress, status and future plans for these and other aspects of the NASA program will be presented.

Description: The catastrophic balloon failure during the first half of the 1980's identified the need for a comprehensive and continuing balloon research and development (R&D) commitment by NASA. Technical understanding was lacking in many of the disciplines and processes associated with scientific ballooning. A comprehensive balloon R&D plan was developed in 1986 and implemented in 1987. The objectives were to develop the understanding of balloon system performance, limitations, and failure mechanisms. The program consisted of five major technical areas: structures, performance and analysis, materials, chemistry and processing, and quality control. Research activitites have been conducted at NASA/Goddard Space Flight Center (GSFC)-Wallops Flight Facility (WFF), other NASA centers and government facilities, universities, and the balloon manufacturers. Several new and increased capabilities and resources have resulted from this activity. The findings, capabilities, and plan of the balloon R&D program are presented.

Description: Caps have been used to structurally reinforce scientific research balloons since the late 1950's. The scientific research balloons used by the National Aeronautics and Space Administration (NASA) use internal caps. A NASA cap placement specification does not exist since no empirical information exisits concerning cap placement. To develop a cap placement specification, NASA has completed two in-hangar inflation tests comparing the structural contributions of internal caps and external caps. The tests used small scale test balloons designed to develop the highest possible stresses within the constraints of the hangar and balloon materials. An externally capped test balloon and an internally capped test balloon were designed, built, inflated and simulated to determine the structural contributions and benefits of each. The results of the tests and simulations are presented.

Description: Rocket data have been used to evaluate the characteristics of precipitating relativistic electrons and their effects on the electrodynamic structure of the middle atmosphere. These data were obtained at Poker Flat, Alaska, on May 13 and 14, 1990, during a midday, highly relativistic electron (HRE) precipitation event. Solid state detectors were used to measure the electron fluxes and their energy spectra. An X ray scintillator was included on each flight to measure bremsstrahlung X rays produced by energetic electrons impacting on the upper atmosphere. However, these were found the be of negligible importance for this particular event. The energy deposition by the electrons has been determined from the flux measurements and compared with in situ measurements of the atmospheric electrical response. The electrodynamic measurements were obtained by the same rockets and additionally on May 13, with an accompanying rocket. The impact flux was highly irregular, containing short-lived bursts of relativistic electrons, mainly with energies below 0.5 MeV and with fluxes most enhanced between pitch angles of 0 deg - 20 deg. Although the geostationary counterpart of this measured event was considered to be of relatively low intensity and hardness, energy deposition peaked near 75 km with fluxes approaching an ion pair production rate in excess of 100/cu cm s. This exceeds peak fluxes in relativistic electron precipitation (REP) events as observed by us in numerous rocket soundings since 1976. Conductivity measurements from a blunt probe showed that negative electrical conductivities exceeded positive conductivities down to 50 km or lower, consistent with steady ionization by precipitating electrons above 1 MeV. These findings imply that the electrons from the outer radiation zone can modulate the electrical properties of the middle atmosphere to altitudes below 50 km. During the decline and activity minimum of the current solar cycle, we anticipate the occurence of similar events but with fluxes 1-2 orders of magnitude above that reported here, based on studies of earlier solar cycles (e.g., Baker et al., 1993).

Description: Nitrous oxide (N2O) measured on board the ER-2 aircraft during the Airborne Arctic Stratospheric Expedition 2 (AASE 2) has been used to monitor descent of air inside the Arctic vortex between October 1991 and March 1992. Monthly mean N2O fields are calculated from the flight data and then compared with mean fields calculated from the high-resolution Geophysical Fluid Dynamics Laboratory general circulation model SKYHI in order to evaluate the model's simulation of the polar vortex. From late fall through winter the model vortex evolves in much the same way as the 1991-1992 vortex, with N2O gradients at the edge becoming progressively steeper. The October to March trends in N2O profiles inside the vortex are used to verify daily net heating rates in the vortex that were computed from clear sky radiative heating rates and National Meteorological Center temperature observations. The computed heating rates successfully estimate the descent of vortex air from December through February but suggest that before December, air at high latitudes may not be isolated from the midlatitudes. SKYHI heating rates are in good agreement with the computed rates but tend to be slightly higher (i.e., less cooling) due to meteorological differences between SKYHI and the 1991-1992 winter. Three ER-2 flights measured N2O just north of the subtropical jet. These low-midlatitude profiles show only slight differences from the high-midlatitude profiles (45 deg - 60 deg N), indicating strong meridional mixing in the midlatitude 'surf zone.' Mean midwinter N2O profiles inside and outside the vortex calculated from AASE 2 data are shown to be nearly identical to 1989 AASE profiles, pointing to the N2O/potential temperature relationship as an excellent marker for vortex air.

Description: The combined Nimbus 7 solar backscattered ultraviolet (SBUV) and NOAA 11 SBUV/2 ozone data, covering a period of more than a solar cycle (about 15 years), are used to study the UV response of ozone in the stratosphere. The study shows that about 2% change in total column ozone and about 5-7% change in ozone mixing ratio in the upper stratosphere (0.7 to 2 hPa) may be attributed to the change in the solar UV flux over a solar cycle. In the upper stratosphere, where photochemical processes are expected to play a major role, the measured solar cycle variation of ozone is significantly larger than inferred either from the photochemical models or from the ozone response to the 27-day solar UV modulation. For example, the observed solar cycle related change in ozone mixing ratio at 2 hPa is about 1% for 1% change in the solar UV flux near 200 nm. The inferred change in ozone from either the photochemical models or from the 27-day ozone-UV response is about a factor of 2-3 lower than this value.

Description: Vertical profiles of N2O and NO(y) taken by the ER-2 outside the vortex are used to construct average vertical profiles of F(NO(y)) = NO(y)/(A-N2O), where A is the tropospheric content of N2O three years prior to the measurements. The southern hemisphere had less nitrous oxide in the range 400 less than Theta less than 470 K, by up to 25% relative to the northern hemisphere. F(NO(y)) is the ratio of NOy produced to N2O lost in a stratospheric air mass since entry from the troposphere. The profiles of F(NO(y)) have the following characteristics: (1) Relative to 1991-1992, a year without denitrification inside or outside the vortex, the northern hemisphere in 1988-1989 showed denitrification outside the vortex ranging up to 25% and averaging 17% above Theta = 425 K. (2) Relative to the northern hemisphere in 1991-1992, the southern hemisphere in 1987 showed denitrification outside the vortex ranging up to 32% and averaging 20% above Theta = 400 K. (3) Below Theta = 400 K the southern hemisphere showed enhancements of F(NO(y)) relative to the northern hemisphere in 1991-1992 ranging up to 200% at Theta = 375 K, outside the vortex. Corresponding profiles of residual water, R(H2O) = H2O - 2(1.6 - CH4), are considered and shown to be consistent with those of F(NO(y)) in the sense that they show deficits outside the Antarctic vortex, which was both dehydrated and denitrified, but not outside the 1988-1989 Arctic vortex, which was denitrified but not dehydrated. R(H2O) is the water content of stratospheric air with the contribution from methane oxidation subtracted. Comparison of F(NO(y)) and R(H2O) below 400 K outside the Antarctic vortex leads to the suggetion that dehydration in the Antarctic vortex occurs by the sedimentation of ice crystals large enough to fall out of the stratosphere, whereas denitrification occurs mainly on mixed nitric acid-water crystals which evaporate below the base of the vortex at Theta = 400 K but above the tropopause.

Description: During January and August 1985, the scanning radiometers of the Earth Radiation Budget Experiment(ERBE) aboard the Earth Radiation Budget Satellite (ERBS) and the NOAA-9 satellite were operated in along-track scanning modes. Along-track scanning permits the study of many measurement problems. It provides the data for developing a limb-darkening model for a single site over a short period of time and also permits the indentification of the scene from data taken at smaller nadir angles. The earth-emitted radiation measured by the scanners has been analyzed to produce limb-darkening models for a variety of scene types. Limb-darkening models relate the radiance in any given direction to the radiant flux. The scene types were computed using measurements within 10 deg of zenith. The models have values near zenith of 1.02-1.09. The typical zenith values of the model are 1.06 for both day and night for ERBS, and for NOAA-9, 1.06 for day and 1.05 for night. Mean models are formed for the ERBS and NOAA-9 results and are found to differ less than 1%, the ERBS results being the higher. The models vary about 1% with latitude near zenith and agree with earlier models that were used to analyze ERBE data typically to 2%.

Description: One of the oldest mysteries in geomagnetism is the linkage between solar and geomagnetic activity. In investigating the causes of geomagnetic storms occurring during solar maximum, the following topics are discussed: solar phenomena; types of solar wind; magnetic reconnection and magnetic storms; an interplanetary example; and future space physics missions.

Description: Atmospheric mass loading produces a primarily vertical displacement of the Earth's crust. This displacement is correlated with surface pressure and is large enough to be detected by very long baseline interferometry (VLBI) measurements. Using the measured surface pressure at VLBI stations, we have estimated the atmospheric loading term for each station location directly from VLBI data acquired from 1979 to 1992. Our estimates of the vertical sensitivity to change in pressure range from 0 to -0.6 mm/mbar depending on the station. These estimates agree with inverted barometer model calculations (Manabe et al., 1991; vanDam and Herring, 1994) of the vertical displacement sensitivity computed by convolving actual pressure distributions with loading Green's functions. The pressure sensitivity tends to be smaller for stations near the coast, which is consistent with the inverted barometer hypothesis. Applying this estimated pressure loading correction in standard VLBI geodetic analysis improves the repeatability of estimated lengths of 25 out of 37 baselines that were measured at least 50 times. In a root-sum-square (rss) sense, the improvement generally increases with baseline length at a rate of about 0.3 to 0.6 ppb depending on whether the baseline stations are close to the coast. For the 5998-km baseline from Westford, Massachusetts, to Wettzell, Germany, the rss improvement is about 3.6 mm out of 11.0 mm. The average rss reduction of the vertical scatter for inland stations ranges from 2.7 to 5.4 mm.

Description: A theoretical model is used to describe and investigate the effects of simultaneous crystallization, radiation loss, and entrainment of cooler material on the temperature of a well-mixed core of an active aa lava flow. Entrainment of crust, levee debris, and base material into the interior of active flows has been observed, but the degree of assimilation and the thermal consequences are difficult to quantify. The rate of entrainment can be constrained by supplementing the theoretical model with information on the crystallization along the path of the flow and estimation of the radiative loss from the flow interior. Application of the model is demonstrated with the 1984 Mauna Loa flow, which was erupted about 30 C undercooled. Without any entrainment of cooler material, the high crystallization rates would have driven temperatures in the core wall above temperatures measured by thermocouple and estimated from glass geothermometry. One plausible scenario for this flow, which agrees with available temperature and crystallinity measurements, has a high initial rate of entrainment during the first 8 hours of travel (a mass ratio of entrained material to fluid core of about 15% if the average temperature of the entrained material was 600 C), which counterbalances the latent heat from approximately 40% crystallization. In this scenario, the model suggests an additional 5% crystallization and a 5% entrainment mass ratio over the subsequent 16-hour period. Measurements of crystallization, radiative losses, and entrainment factors are necessary for understanding the detailed thermal histories of active lava flows.

Description: The purpose of this Note is to present results from an analytic/experimental study that investigated the potential for passively changing blade twist through the use of extension-twist coupling. A set of composite model rotor blades was manufactured from existing blade molds for a low-twist metal helicopter rotor blade, with a view toward establishing a preliminary proof concept for extension-twist-coupled rotor blades. Data were obtained in hover for both a ballasted and unballasted blade configuration in sea-level atmospheric conditions. Test data were compared with results obtained from a geometrically nonlinear analysis of a detailed finite element model of the rotor blade developed in MSC/NASTRAN.

Description: The data from the infrared telescope (IRT), which was flown on space shuttle Challenger Spacelab 2 mission (July 1985), were originally reported by Koch et al. (1987) as originating from near orbital emissions, primarily H2O. In this study, analysis of this data was extended to determine the collisional cross sections for the excitation of the low lying vibrational levels of H2O, present in the orbiter cloud, by atmospheric O(3P). The evaluation of the contribution to the measured signal from solar excitation and ram O excitation of outgassing H2O permits the determination of the H2O column density and the excitation cross section of the (101) level at an O(3P) velocity of approximately 7.75 km/s. Contributions to the radiation in the 1.7-3.0 micron band by transitions from the (100), (001), and multiquantum excited levels are discussed. The findings of the study are (1) the IRT data for the 4.5-9.5 micron and the nighttime data for the 1.7-3.0 micron sensors are consistent with being explained by collision excitation of H2O by O(3P), (2) diurnal variations of 4.5-9.5 micron intensities follow the model predicted O density for a full orbit, (3) daytime increases in the H2O cloud density were not evident, (4) the cross sections for the collisional excitation process are derived and compared to values computated by Johnson (1986) and Redmon et al. (1986), (5) theoretical investigation suggests greater than 60% of the radiation from H2O is a result of multiphoton emission resulting from collisional multiquanta excitation, and (6) the large daytime increase in the 1.7-3.0 micron intensity data suggests that O(+) may likely be instrumental in producing excited H2O(+) through charge exchange.

Description: The paper considers the compressible Rayleigh equation as a model for the Mach wave emission mechanism associated with high-temperature supersonic jets. Solutions to the compressible Rayleigh equation reveal the existence of several families of supersonically convecting instability waves. These waves directly radiate noise to the jet far field. The predicted noise characteristics are compared to previously acquired experimental data for an axisymmetric Mach 2 fully pressure balanced jet operating over a range of jet total temperatures from ambient to 1370 K. The results of this comparison show that the first-order supersonic instability wave and the Kelvin-Hemlhlotz first-, second-, and third-order modes have directional radiation characteristics that are in agreement with observed data. The assumption of equal initial amplitudes for all of the waves leads to the conclusion that the flapping mode of instability dominates the noise radiatio process of supersonic jets. At a jet temperature of 1370 K, supersonic instability waves are predicted to dominate the noise radiated at high frequency at narrow angles to the jet axis.

Description: The objective of the present work is to study the mixing characteristics of a linear array of supersonic rectangular jets under conditions of screech synchronization. The screech synchronization at a fully expanded jet Mach number of 1.61 is achieved by a precise adjustment of the internozzle spacing. To our knowledge, such an experiment on the resonant mixing of screech synchronized multiple rectangular jets has not been reported before. The results are compared with the case where the screech was suppressed in the multijet configuration.

Description: The objective of the present investigation is to assess the effect of the spatial order of accuracy used for the evaluation of the inviscid fluxes on the resolution of higher order quantitites, such as velocity gradients. The viscous terms are computed as second-order accurate with central difference formulas, even though for the explicit part of the algorithm higher order approximations may be used. A viscous/inviscid method is used, and the outer part of the flowfield is computed with the inviscid flow equations. The viscous boundary-layer type flow region close to the body surface is computed with an algebraic eddy viscosity model. Results obtained with the conservative and nonconservative formulations and the viscous/inviscid approach are compared with available experimental data. The effect of grid refinement on the accuracy of the solution is also presented.

Description: Observations of stratospheric column amounts of nitrogen dioxide (NO2), nitric oxide (NO) and nitric acid (HNO3) have been made following major eruptions of the El Chichon and Mt. Pintatubo volcanoes. Midlatitude abundances of NO2 and NO were reduced by as much as 70% in the months following the appearance of the volcanic aerosols as compared to volcanically quite periods. There are heterogeneous reactions which could occur on the volcanic aerosols to convert NO2 into HNO3 but no commensurate increase in HNO3 column amounts was observed at the times of NO2 decrease.

Description: The benefits of using a hypersonic waverider for spacecraft trajectory modification are presented. A waverider is a hypersonic vehicle specifically designed so that the undersurface bow shock is attached to the leading edge, which provides for the highest known lift-to-drag ratios achievable at high Mach number flight. Several viable space missions are suggested which could use such configurations for low-drag aero-assisted maneuvers in planetary atmospheres. It is shown that large changes in the spacecraft velocity vector can be accomplished with acceptably small losses in energy due to drag using a waverider aeroshell. The primary advantage of an aero-assist maneuver is suggested by comparison to a traditional gravity-assist trajectory. Some scaling laws are presented for comparing waveriders designed for different planetary atmospheres, and it is shown that the compositional differences between the terrestrial planets has a minimal impact on waverider design.

Description: The devolatilization of calcium sulfate, which is present in the target rock of the Chicxulub, Mexico impact structure, and dispersal in the stratosphere of the resultant sulfuric acid aerosol have been suggested as a possible mechanism for the Cretaceous-Tertiary extinctions. We measured the amount of SO2 produced from two shock-induced devolatilization reactions of calcium sulfate up to 42 GPa in the laboratory. We found both to proceed to a much lower extent than calculated by equilibrium thermodynamic calculations. Reaction products are found to be approx. 10(exp -2) times those calculated for equilibrium. Upon modeling the quantity of sulfur oxides degassed into the atmosphere from shock devolatilization of CaSO4 in the Chicxulub lithographic section, the resulting 9 x 10(exp 16) to 6 x 10(exp 17) g (in sulfur mass) is lower by a factor of 10-100 than previous upper limit estimates, the related environmental stress arising from the resultant global cooling and fallout of acid rain is insufficient to explain the widespread K-T extinctions.

Description: Energetic atomic (O(+1) and N(+1)) and molecular (O2(+1), NO(+1), and N2(+1)) ions of ionospheric origin were observed in Earth's magnetotail at X approximately -146 R(sub E) during two plasma sheet sunward/tailward flow-reversal events measured by instruments on the GEOTAIL spacecraft. These events were associated with concurrent ground-measured geomagnetic disturbance intensification at auroral-and mid-latitudes (Kp = 7(-)). Energetic ions in the sunward-component and tailward flows were from both the solar wind and ionosphere. Plasma and energetic ions participated in the flows. During tailward flow, ionospheric origin ion abundance ratios at approximately 200-900 km/s in the rest frame were N(+1)/O(+1) = approximately 25-30% and ((O2(+1), NO(+1), and N2(+1))/O(+1) = approximately 1-2%. We argue that tailward flow most likely initiated approximately 80-100 R(sub E) tailward of Earth and molecular ions were in the plasma sheet prior to geomagnetic intensification onset.

Description: Wave forms of BEN (Broadband Electrostatic Noise) in the geomagnetic tail were first detected by the Wave Form Capture reciever on the GEOTAIL spacecraft. The results show that most of the BEN in the plasma sheet boundary layer (PSBL) are not continuous broadband noise but are composed of a series of solitary pulses having a special form which we term 'Electrostatic Solitary Waves (ESW)'. A nonlinear BGK potential model is proposed as the generation mechanism for the ESW based upon a simple particle simulation which considers the highly nonlinear evolution of the electron beam instability. The wave forms produced by this simulation are very similar to those observed by GEOTAIL and suggest that the nonlinear dynamics of the electron beam play an essential role in the generation of ESW.

Description: Radiometric (K-Ar and Ar-40/Ar-39) age determinations of volcanic and volcaniclastic rocks, combined with structural, gravity, and seismic reflection data, are used to constrain the age of sedimentary strata contained within the seismically and volcanically active northern Malawi (Nyasa) rift and to characterize changes in basin and flank morphologies with time. Faulting and volcanism within the Tukuyu-Karonga basin began at approximately 8.6 Ma, when sediments were deposited in abroad, initially asymmetric lake basin bounded on its northeastern side by a border fault system with minor topographic relief. Extensions, primarily by a slip along the border fault, and subsequent regional isostatic compensation led to the development of a 5-km-deep basin bounded by broad uplifted flanks. Along the low-relief basin margin opposite border fault, younger stratigraphic sequences commonly onlap older wedge-shaped sequences, although their internal geometry is often progradational. Intrabasinal faulting, flankuplift, and basaltic and felsic volcanism from centers at the northern end of the basin became more important at about 2.5 Ma when cross-rift transfer faults developed to link the Tukuyu-Karonga basin to the Rukwa basin. Local uplift and volcanic construction at the northern end of the basin led to a southeastward shift in the basin's depocenter. Sequence boundaries are commonly erosional along this low-relief (hanging wall) margin and conformable in the deep lake basin. The geometry of stratigraphic sequences and the distribution of the erosion indicate that horizontal and vertical crustal movements both across and along the length of the rift basin led to changes in levels of the lake, irrespective of paleoclimatic fluctuations.

Description: We report on the observations of a number of quasi-dc electric field events associated with large-scale atmospheric weather formations. The observations were made by the electric field experiment onboard the San Marco D satellite, operational in an equatorial orbit from May to December 1988. Several theoretical studies suggest that electric fields generated by thunderstorms are present at high altitudes in the ionosphere. In spite of such favorable predictions, weather-related events are not often observed since they are relatively weak. We shall report here on a set of likely E field candidates for atmospheric-ionospheric causality, these being observed over the Indonesian Basin, northern South America, and the west coast of Africa; all known sites of atmospheric activity. As we shall demonstrate, individual events often be traced to specific active weather features. For example, a number of events were associated with spacecraft passages near Hurricane Joan in mid-October 1988. As a statistical set, the events appear to coincide with the most active regions of atmospheric weather.

Description: A radiation model, together with National Meteorological Center temperature observations, was used to compute daily net heating rates in the northern hemisphere (NH) for the Arctic late fall and winter periods of both 1988-1989 and 1991-1992 and in the southern hemisphere (SH) for the Antarctic fall and winters of 1987 and 1992. The heating rates were interpolated to potential temperature (theta) surfaces between 400 K and 2000 K and averaged within the polar vortex, the boundary of which was determined by the maximum gradient in potential vorticity. The averaged heating rates were used in a one-dimensional vortex interior descent model to compute the change in potential temperature with time of air parcels initialized at various theta values, as well as to compute the descent in log pressure coodinates. In the NH vortex, air parcels which were initialized at 18 km on November 1, descended about 6 km by March 21, while air initially at 25 km descended 9 km in the same time period. this represents an average descent rate in the lower stratosphere of 1.3 to 2 km per month. Air initialized at 50 km descended 27 km between November 1 and March 21. In the SH vortex, parcels initialized at 18 km on March 1, descended 3 km, while air at 25 km descended 5-7 km by the end of October. This is equivalent to an average descent in the lower stratosphere of 0.4 to 0.9 km per month during this 8-month period. Air initialized at 52 km descended 26-29 km between March 1 and October 31. In both the NH and the SH, computed descent rates increased markedly with height. The descent for the NH winter of 1992-1993 and the SH winter of 1992 computed with a three-dimensional trajectory model using the same radiation code was within 1 to 2 km of that calculated by the one-dimensional model, thus validating the vortex averaging procedure. The computed descent rates generally agree well with observations of long-lived tracers, thus validating the radiative transfer model.

Description: In this paper we report radiometric measurements of tropospheric brightness temperatures obtained during the AASE 2 experiment. These measurements represent the first attempt to characterize effective radiative temperatures as seen from above the troposphere during the Arctic winter. The reported measurements include brightness temperatures at 6.7 and 10.5 microns as seen from the NASA DC-8 aircraft flying at about 11 km altitude. We also present radiative transfer calculations to estimate the effect of tropospheric brightness temperature on the lower stratospheric heating rates. Because of the recent massive eruption of the Pinatubo volcano, we also discuss the effects of a volcanic aerosol layer. It is concluded that small particles like the volcanic aerosol or polar stratospheric clouds (PSCs) type 1 do not affect stratospheric heating rates by much; on the other hand, larger particles, PSCs types 2 and 3, may have significant effects on heating rates and consequently on dynamics of the lower stratosphere. The dynamical effects of local stratospheric temperature variations are briefly discussed.

Description: We report tropospheric (altitudes greater than 5 km) observations of CO2, CO, CH4, and light hydrocarbons (C2-C4) over the latitude range from 90 deg N to 23 deg S recorded onboard the NASA DC-8 aircraft during the winter 1992 Second Airborne Arctic Stratospheric Expedition (AASE-2). Mixing ratios for these species exhibited significant north-south gradients with maximum values in subpolar and arctic regions and minima over the southern tropics. At latitudes greater than 40 deg N, the mixing ratios of most species increased significantly over the course of the 3-month measurement period. Also at high northern latitudes, the variations of all relatively long-lived reactive carbon species were linearly correlated with fluctuations of CO2 with CO, CH4, C2H6, C2H2, C3H8, and n-C4H10 exhibiting average enhancement ratios in terms of ppbv(X)/ppmb(CO2) of 13.8, 8.4, 0.21, 0.075, 0.085, and 0.037, respectively.

Description: Vertical column measurements of the gaseous composition of the tropical stratosphere were made from the NASA DC-8 aircraft early in 1992. As anticipated, the burdens of the stratospheric source gases (e.g., O3, HF, HCl, ClNO3, HNO3) were reduced from their mid-latitude values due to increased uplift and photolysis. The tracers revealed considerably more uplift near the equator than the sub-tropics. For example, the HF burdens at +/- 20 deg latitude were nearly double those at 5 deg N. This, together with results obtained from other long-lived gases (e.g. N2O, CH4, CF2Cl2) indicates that volume mixing ratios found at 22 km altitude at mid-latitudes occurred at 26 km in the sub-tropics and at 30 km in the equatorial zone. This zone of uplift was symmetrical about the equator even though the sun was overhead at 20 deg S.

Description: We welcome this opportunity which Drs. Ricard, Sabadini and Spada (RSS) have offered us to elaborate on some points concerning the connection between convective circulations and rotational dynamics. The relationship of the linear viscoelastic normal-mode theory to other approaches, such as viscous and the non-linear viscoelastic treatments, can be found in Moser et al. (1993). We will address the issues raised by RSS by first going over the reference system. This will be followed by a discussion concerning long-term polar wander and relative angular momentum. We will also go over the issues concerning the off-diagonal terms in the total moment of inertia and polar wander.

Description: In late July and early August of 1991, a major suborbital scientific campaign (NLC-91) involving scientists from eight countries was conducted as ESRANGE, Kiruna, Sweden and at Heiss Island, Russia. The purpose of the program was to investigate the chemical, dynamical, and electrodynamical properties of the polar summer mesosphere. Thirty one rocket flights were coordinated with two coherent radar facilities, EISCAT and CUPRI, and with other ground-based observatories and facilities. This permitted direct comparison between the in situ measurements and those obtained by remote sensing of the mesosphere via continuous ground-based monitoring. The primary objectives of the campaign were to study noctilucent clouds (NLCs) and polar mesospheric summer echoes (PMSEs), including their possible relationship to local aerosols and/or small scale turbulence. This overview describes the scientific program, discusses the geophysical conditions during launch activities, and reviews some of the preliminary results. More detailed results can be found in the papers which follow.

Description: The International Sun-Earth Explorer 3 (ISEE-3) magnetic field and plasma electron data from Jan - March 1983 have been searched to study thin current sheets in the deep tail region. 33 events were selected where the spacecraft crossed through the current sheet from lobe to lobe within 15 minutes. The average thickness of the observed current sheets was 2.45 R(sub E), and in 24 cases the current sheet was thinner than 3.0 R(sub E); 6 very thin current sheets (thickness lambda less than 0.5 R(sub E) were found. The electron data show that the very thin current sheets are associated with considerable temperature anisotropy. On average, the electron gradient current was about 17% of the total current, whereas the current arising from the electron temperature anisotropy varied between 8-45% of the total current determined from the lobe field magnitude.

Description: The map of the coseismic displacement field generated by interferometric processing of synthetic aperture radar (SAR) images taken before and after the June 28, 1992, Landers earthquake sequence brings new insights into the nature of deformation caused by these earthquakes. We use the interferometric map generated by Massonnet et al. (1993) to analyze the surface displacement field in the vicinity of the fault trace. Complexities in the fringe pattern near the fault reflect short-wavelength variations of the surface rupture and slip distribution, and attest to large displacement gradients. Along two sections of the fault, characteristic fringe patterns can be recognized, contrasting in density and direction with patterns observed away from the rupture. In order to understand the observed fringe patterns, we compute synthetic interferograms in three simple cases: (1) rigid-body rotations about a vertical axis, (2) about a horizontal axis (tilt), and (3) distributed, simple shear. The orientation and spatial separation of interferometric fringes predicted by these models help constrain near-field deformation and rupture parameters. Where the Kickapoo fault connects with the Homestead Valley fault, the interferogram shows a clear pattern of parallel N20 deg W fringes separated by about 160 m. This pattern and vertical offsets measured along the Kickapoo fault suggest that the block between this fault and the Johnson Valley fault may have been tilted, down to the west. A 5-km block lifted by 1 m on one side would be tilted by an angle of 0.01 deg (190 microrad), producing fringes separated by about 160 m, parallel to the tilt axis. Such a tilt, parallel to a N20 deg W direction, would account for the gradual, northward increase of the vertical slip component observed along the Kickapoo fault. This tilt may also explain the 1 m of reverse slip observed along the 'slip gap' section of the Homestead Valley break. Between the southern end of the Johnson Valley fault and the Eureka Peak fault, where no surface rupture has been mapped, the dense pattern of fringes implies distributed shear, probably resulting from fault slip at depth. The density and direction of the fringes in the gap are consistent with a right-lateral slip of 1.2-3.8 m on a blind fault locked above the depth of 1.5-2 km. Such observations of small wavelength features in the SAR interferogram bring new insights into the near-field displacement gradient and thus on response of the uppermost crust to seismic rupture.

Description: Global distributions of surface and atmospheric cloud radiative forcing parameters have been derived using parameterized radiation models with satellite meteorological data from the International Satellite Cloud Climatology Project, and directly measured top-of-atmosphere radiative fluxes from the Earth Radiation Budget Experiment. Specifically, shortwave, longwave, and total cloud forcing at the surface, and column-averaged values of longwave cloud forcing of the atmosphere were derived for the midseasonal months of April, July, and October 1985 and January 1986, covering a complete annual cycle. Seasonal variability is illustrated by comparing the results for July 1985 and January 1986, which represent the seasonal extremes. Surface shortwave cloud forcing is always negative, representing a cooling of the surface, with strongest cooling (-120 to -180 W/sq m) occurring over midlatitude storm tracks of the summer hemisphere. Surface longwave cloud forcing is always positive, representing a warming of the surface, with strongest warming (60 to 75 W/sq m) occurring over storm tracks of the winter hemisphere. Zonal averages show the entire summer hemisphere dominated by shortwave cooling, the middle and high latitudes of the winter hemisphere dominated by longwave warming, and a broad zone of transition in between. The globally averaged total cloud forcing amounts to a cooling throughout the year, ranging from a low of about -12 W/sq m for July 1985 to a high of about -25 W/sq m for January 1986. The longwave cloud forcing of the atmosphere shows a strong warming over deep convective regions in the tropics and a moderate cooling outside the tropics, amounting to a weak cooling (-2 to -5 W/sq m) in the global average. Comparisons of the results with general circulation model simulations show broad qualitative agreement regarding the locations of prominent warming and cooling regions. Quantitative comparisons, on the other hand, show significant differences between the magnitudes of warming and cooling in these regions. Most of the larger differences can be attributed to known deficiences of the general circulation model simulations. Comparisons with satellite-derived results of other investigators show much better agreement.

Description: The acceleration of protons in a dynamically evolving magnetotail is investigated by tracing particles in the fields obtained from a three-dimensional resistive magnetohydrodynamic (MHD) simulation. The MHD simulation, representing plasmoid formation and ejection through a near-Earth reconnection process, leads to cross-tail electric fields of up to approximately 4 mV/m with integrated voltages across the tail of up to approximately 200 kV. Energization of particles takes place over a wide range along the tail, due to the large spatial extent of the increased electric field together with the finite cross-tail extent of the electric field region. Such accelerated particles appear earthward of the neutral line over a significant portion of the closed field line region inside of the separatrix, not just in the vicinity of the separatrix. Two different acceleration processes are identified: a 'quasi-potential' acceleration, due to particle motion in the direction of the cross-tail electric field, and a 'quasi-betatron' effect, which consists of multiple energy gains from repeated crossings of the acceleration region, mostly on Speiser-type orbits, in the spatially varying induced electric field. The major source region for accelerated particles in the hundreds of keV range is the central plasma sheet at the dawn flank outside the reconnection site. Since this source plasma is already hot and dense, its moderate energization by a factor of approximately 2 may be sufficient to explain the observed increases in the energetic particle fluxes. Particles from the tail are the source of beams at the plasma sheet/lobe boundary. The temporal increase in the energetic particle fluxes, estimated from the increase in energy gain, occurs on a fast timescale of a few minutes, coincident with a strong increase in B(sub z), despite the fact that the inner boundary ('injection boundary') of the distribution of energized particles is fairly smooth.

Description: A high-precision radiometric satellite tracking system, Doppler Orbitography and Radio-positioning Integrated by Satellite system (DORIS), has recently been developed by the French space agency, Centre National d'Etudes Spatiales (CNES). DORIS was designed to provide tracking support for missions such as the joint United States/French TOPEX/Poseidon. As part of the flight testing process, a DORIS package was flown on the French SPOT 2 satellite. A substantial quantity of geodetic quality tracking data was obtained on SPOT 2 from an extensive international DORIS tracking network. These data were analyzed to assess their accuracy and to evaluate the gravitational modeling enhancements provided by these data in combination with the Goddard Earth Model-T3 (GEM-T3) gravitational model. These observations have noise levels of 0.4 to 0.5 mm/s, with few residual systematic effects. Although the SPOT 2 satellite experiences high atmospheric drag forces, the precision and global coverage of the DORIS tracking data have enabled more extensive orbit parameterization to mitigate these effects. As a result, the SPOT 2 orbital errors have been reduced to an estimated radial accuracy in the 10-20 cm RMS range. The addition of these data, which encompass many regions heretofore lacking in precision satellite tracking, has significantly improved GEM-T3 and allowed greatly improved orbit accuracies for Sun-synchronous satellites like SPOT 2 (such as ERS 1 and EOS). Comparison of the ensuing gravity model with other contemporary fields (GRIM-4C2, TEG2B, and OSU91A) provides a means to assess the current state of knowledge of the Earth's gravity field. Thus, the DORIS experiment on SPOT 2 has provided a strong basis for evaluating this new orbit tracking technology and has demonstrated the important contribution of the DORIS network to the success of the TOPEX/Poseidon mission.

Description: The presence of anisotropic plasma distributions, trapped at the Earth's magnetic equator, has consequences for the electric field structure which must exist in equilibrium along the magnetic field line. Data from SCATHA and Dynamics Explorer 1 indicate that the core ion distributions at the magnetic equator can be well described as bi-Maxwellian distributions, with a perpendicular temperature an order of magnitude larger than the parallel temperature. A collisionless model is developed for the variation in plasma parameters, following the forms developed by Whipple (1977). If the core electron anisotropy is low, the resulting electric field of approximately 0.1 microV/m is pointed away from the equator. Under these conditions the self-consistent electric field will not overcome the effects of magnetic trapping. The resulting potential distribution results in a local maximum in total plasma density at the equator. Only when the electron distribution is primarily field-aligned can there be a density minimum at the equator. Comparisons are made between this model and the observed variations in DE 1 plasma parameters with latitude.

Description: A combined 3-dimensional circulation model and aerosol microphysical/transport model is used to simulate the dispersion of the Mt. Pinatubo volcanic cloud in the stratosphere for the first few months following the eruption. Radiative heating of the cloud due to upwelling infrared radiation from the troposphere is shown to be an important factor affecting the transport. Without cloud heating, cloud material stays mostly north of the equator, whereas with cloud heating, the cloud is transported southward across the equator within the first two weeks following the eruption. Generally the simulations agree with Total Ozone Mapping Spectrometer (TOMS), Advanced Very High Resolution Radiometer (AVHRR), and Stratospheric Aerosol and Gas Experiment (SAGE) satellite observations showing the latitude distribution of cloud material to be between about 20 deg S and 30 deg N within the first few months. Temperature perturbations in the stratosphere induced by the aerosol heating are generally 1-4 K, in the range of those observed.

Description: We use geodetic data from Very Long Baseline Interferometry (VLBI) to determine the pre- and postseismic velocities of two sites. We then place limits on variations in interseismic strain buildup. The 1987 and 1988 Gulf of Alaska earthquakes (each Ms = 7.6) broke the Pacific plate interior. During the earthquakes the Cape Yakataga site moved 78 mm toward southwest. During the 1989 Loma Prieta earthquake (Ms = 7.1) the Fort Ord site moved 48 mm toward north. Baselines (a) from Fairbanks to Cape Yakataga and (b) from Mojave to Fort Ord change at nearly the same rate before and after the earthquakes. Postseismic transients, which we determine from differences between post- and preseismic rates, are minor: at Cape Yakataga the transient is 3 +/- 4 mm in a postseismic interval of 23 months, and at Fort Ord the transient is 6 +/- 5 mm in 21 months. The slip beneath the Loma Prieta rupture needed to generate the Fort Ord transient is 0.22 +/- 0.19 m, one-tenth the coseismic slip (2 m). We analyze elastic lithosphere-viscous asthenosphere models to determine that the characteristic time describing exponential decay in deep fault slip is longer than 6 years. The VLBI measurements are consistent with uniform interseismic strain buildup. They disagree with fast postseismic rates caused by an asthenosphere with very low viscosity.

Description: The AEPI (Atmospheric Emissions Photometric Imager) experiment on the ATLAS-1 shuttle mission (launched March 24, 1992) imaged the earth night airglow emission in O2 Atmospheric (0,0) bands, at 762.0 nm. Earthward views of O2 A bands show structure from gravity waves which exhibit extended horizontal structure with horizontal wavelenghts on the order of 50-100 km. These observations of the O2 A (0,0) bands are particularly interesting since in this wavelength the lower atmosphere absorbs all the earth-reflected emissions and most of the spectrally diffuse backgrounds. Herein we present observations of gravity waves using a topside airglow imaging technique.

Description: Fujii et al. (1994) obtained characteristics of the electrodynamic parameters, that is, field-aligned currents, electric fields, and electron precipitation, which are associted with auroral substorm events in the nighttime sector, through a unique analysis that places the ionospheric measurements of these parameters into the context of a generic substorm determined from global auroral images. In this paper we investigate in considerably more detail the characteristics of the field-aligned currents using data from the same set of passes as the previuos study. We show for the first time that the net upward field-aligned currents throughout the surge and surge horn are sufficient to account for most if not all of the converging currents of the auroral electrojets. Current densities are largest in the surge and surge horn. Current region continuity does not appear to exist across the substorm bulge region. Much of the auroral substorm field-aligned current is composed of filamentary currents and finite current segments at large angles to each other. The westward electrojet may contain large gradients in intensity both in local time and latitude due to sets of localized field-aligned currents. The net downward current for several hours to the west of the surge is insufficient to account for the eastward electrojet, consistent with the concept that this electrojet originates primarily on the dayside. Our pattern of field-aligned currents associated with the surge has common features and also differs significantly from the patterns previously derived from data from radars and ground-based magnetometer arrays. Our pattern is considerably more complex, probably due to the much higher resolution in latitude of the satellite data. It is also larger in area, since our average substorm is much larger than those pertaining to the previous patterns, giving a substorm wedge considerably wider than that obtained from the radar and array data.

Description: An analytical model of the bidirectional reflectance for optically semi-infinite plant canopies has been extended to describe the reflectance of finite depth canopies contributions from the underlying soil. The model depends on 10 independent parameters describing vegetation and soil optical and structural properties. The model is inverted with a nonlinear minimization routine using directional reflectance data for lawn (leaf area index (LAI) is equal to 9.9), soybeans (LAI, 2.9) and simulated reflectance data (LAI, 1.0) from a numerical bidirectional reflectance distribution function (BRDF) model (Myneni et al., 1988). While the ten-parameter model results in relatively low rms differences for the BRDF, most of the retrieved parameters exhibit poor stability. The most stable parameter was the single-scattering albedo of the vegetation. Canopy albedo could be derived with an accuracy of less than 5% relative error in the visible and less than 1% in the near-infrared. Sensitivity were performed to determine which of the 10 parameters were most important and to assess the effects of Gaussian noise on the parameter retrievals. Out of the 10 parameters, three were identified which described most of the BRDF variability. At low LAI values the most influential parameters were the single-scattering albedos (both soil and vegetation) and LAI, while at higher LAI values (greater than 2.5) these shifted to the two scattering phase function parameters for vegetation and the single-scattering albedo of the vegetation. The three-parameter model, formed by fixing the seven least significant parameters, gave higher rms values but was less sensitive to noise in the BRDF than the full ten-parameter model. A full hemispherical reflectance data set for lawn was then interpolated to yield BRDF values corresponding to advanced very high resolution radiometer (AVHRR) scan geometries collected over a period of nine days. The resulting parameters and BRDFs are similar to those for the full sampling geometry, suggesting that the limited geometry of AVHRR measurements might be used to reliably retrieve BRDF and canopy albedo with this model.

Description: ARC2D is a computational fluid dynamics program developed at the NASA Ames Research Center specifically for airfoil computations. The program uses implicit finite-difference techniques to solve two-dimensional Euler equations and thin layer Navier-Stokes equations. It is based on the Beam and Warming implicit approximate factorization algorithm in generalized coordinates. The methods are either time accurate or accelerated non-time accurate steady state schemes. The evolution of the solution through time is physically realistic; good solution accuracy is dependent on mesh spacing and boundary conditions. The mathematical development of ARC2D begins with the strong conservation law form of the two-dimensional Navier-Stokes equations in Cartesian coordinates, which admits shock capturing. The Navier-Stokes equations can be transformed from Cartesian coordinates to generalized curvilinear coordinates in a manner that permits one computational code to serve a wide variety of physical geometries and grid systems. ARC2D includes an algebraic mixing length model to approximate the effect of turbulence. In cases of high Reynolds number viscous flows, thin layer approximation can be applied. ARC2D allows for a variety of solutions to stability boundaries, such as those encountered in flows with shocks. The user has considerable flexibility in assigning geometry and developing grid patterns, as well as in assigning boundary conditions. However, the ARC2D model is most appropriate for attached and mildly separated boundary layers; no attempt is made to model wake regions and widely separated flows. The techniques have been successfully used for a variety of inviscid and viscous flowfield calculations. The Cray version of ARC2D is written in FORTRAN 77 for use on Cray series computers and requires approximately 5Mb memory. The program is fully vectorized. The tape includes variations for the COS and UNICOS operating systems. Also included is a sample routine for CONVEX computers to emulate Cray system time calls, which should be easy to modify for other machines as well. The standard distribution media for this version is a 9-track 1600 BPI ASCII Card Image format magnetic tape. The Cray version was developed in 1987. The IBM ES/3090 version is an IBM port of the Cray version. It is written in IBM VS FORTRAN and has the capability of executing in both vector and parallel modes on the MVS/XA operating system and in vector mode on the VM/XA operating system. Various options of the IBM VS FORTRAN compiler provide new features for the ES/3090 version, including 64-bit arithmetic and up to 2 GB of virtual addressability. The IBM ES/3090 version is available only as a 9-track, 1600 BPI IBM IEBCOPY format magnetic tape. The IBM ES/3090 version was developed in 1989. The DEC RISC ULTRIX version is a DEC port of the Cray version. It is written in FORTRAN 77 for RISC-based Digital Equipment platforms. The memory requirement is approximately 7Mb of main memory. It is available in UNIX tar format on TK50 tape cartridge. The port to DEC RISC ULTRIX was done in 1990. COS and UNICOS are trademarks and Cray is a registered trademark of Cray Research, Inc. IBM, ES/3090, VS FORTRAN, MVS/XA, and VM/XA are registered trademarks of International Business Machines. DEC and ULTRIX are registered trademarks of Digital Equipment Corporation.

Description: Panel method computer programs are software tools of moderate cost used for solving a wide range of engineering problems. The panel code PMARC_12 (Panel Method Ames Research Center, version 12) can compute the potential flow field around complex three-dimensional bodies such as complete aircraft models. PMARC_12 is a well-documented, highly structured code with an open architecture that facilitates modifications and the addition of new features. Adjustable arrays are used throughout the code, with dimensioning controlled by a set of parameter statements contained in an include file; thus, the size of the code (i.e. the number of panels that it can handle) can be changed very quickly. This allows the user to tailor PMARC_12 to specific problems and computer hardware constraints. In addition, PMARC_12 can be configured (through one of the parameter statements in the include file) so that the code's iterative matrix solver is run entirely in RAM, rather than reading a large matrix from disk at each iteration. This significantly increases the execution speed of the code, but it requires a large amount of RAM memory. PMARC_12 contains several advanced features, including internal flow modeling, a time-stepping wake model for simulating either steady or unsteady (including oscillatory) motions, a Trefftz plane induced drag computation, off-body and on-body streamline computations, and computation of boundary layer parameters using a two-dimensional integral boundary layer method along surface streamlines. In a panel method, the surface of the body over which the flow field is to be computed is represented by a set of panels. Singularities are distributed on the panels to perturb the flow field around the body surfaces. PMARC_12 uses constant strength source and doublet distributions over each panel, thus making it a low order panel method. Higher order panel methods allow the singularity strength to vary linearly or quadratically across each panel. Experience has shown that low order panel methods can provide nearly the same accuracy as higher order methods over a wide range of cases with significantly reduced computation times; hence, the low order formulation was adopted for PMARC_12. The flow problem is solved by modeling the body as a closed surface dividing space into two regions: the region external to the surface in which an unknown velocity potential exists representing the flow field of interest, and the region internal to the surface in which a known velocity potential (representing a fictitious flow) is prescribed as a boundary condition. Both velocity potentials are required to satisfy Laplace's equation. A surface integral equation for the unknown potential external to the surface can be written by applying Green's Theorem to the external region. Using the internal potential and zero flow through the surface as boundary conditions, the unknown potential external to the surface can be solved for. When the internal flow option, which allows the analysis of closed ducts, wind tunnels, and similar internal flow problems, is selected, the geometry is modeled such that the flow field of interest is inside the geometry and the fictitious flow is outside the geometry. Items such as wings, struts, or aircraft models can be included in the internal flow problem. The time-stepping wake model gives PMARC_12 the ability to model both steady and unsteady flow problems. The wake is convected downstream from the wake-separation line by the local velocity field. With each time step, a new row of wake panels is added to the wake at the wake-separation line. Time stepping can start from time t=0 (no initial wake) or from time t=t0 (an initial wake is specified). A wide range of motions can be prescribed, including constant rates of translation, constant rate of rotation about an arbitrary axis, oscillatory translation, and oscillatory rotation about any of the three coordinate axes. Investigators interested in a visual representation of the phenomenon they are studying with PMARC_12 may want to consider obtaining the program GVS (ARC-13361), the General Visualization System. GVS is a Silicon Graphics IRIS program which was created for the purpose of supporting the scientific visualization needs of PMARC_12. GVS is available separately from COSMIC. PMARC_12 is written in standard FORTRAN 77, with the exception of the NAMELIST extension used for input. This makes the code fairly machine independent. A compiler which supports the NAMELIST extension is required. The amount of free disk space and RAM memory required for PMARC_12 will vary depending on how the code is dimensioned using the parameter statements in the include file. The recommended minimum requirements are 20Mb of free disk space and 4Mb of RAM. PMARC_12 has been successfully implemented on a Macintosh II running System 6.0.7 or 7.0 (using MPW/Language Systems Fortran 3.0), a Sun SLC running SunOS 4.1.1, an HP 720 running HP-UX 8.07, an SGI IRIS running IRIX 4.0 (it will not run under IRIX 3.x.x without modifications), an IBM RS/6000 running AIX, a DECstation 3100 running ULTRIX, and a CRAY-YMP running UNICOS 6.0 or later. Due to its memory requirements, this program does not readily lend itself to implementation on MS-DOS based machines. The standard distribution medium for PMARC_12 is a set of three 3.5 inch 800K Macintosh format diskettes and one 3.5 inch 1.44Mb Macintosh format diskette which contains an electronic copy of the documentation in MS Word 5.0 format for the Macintosh. Alternate distribution media and formats are available upon request, but these will not include the electronic version of the document. No executables are included on the distribution media. This program is an update to PMARC version 11, which was released in 1989. PMARC_12 was released in 1993. It is available only for use by United States citizens.

Description: This program determines the supersonic flowfield surrounding three-dimensional wing-body configurations of a delta wing. It was designed to provide the numerical computation of three dimensional inviscid, flowfields of either perfect or real gases about supersonic or hypersonic airplanes. The governing equations in conservation law form are solved by a finite difference method using a second order noncentered algorithm between the body and the outermost shock wave, which is treated as a sharp discontinuity. Secondary shocks which form between these boundaries are captured automatically. The flowfield between the body and outermost shock is treated in a shock capturing fashion and therefore allows for the correct formation of secondary internal shocks . The program operates in batch mode, is in CDC update format, has been implemented on the CDC 7600, and requires more than 140K (octal) word locations.

Description: MSIS is an empirical model of the thermosphere based on Mass Spectrometer and Incoherent Scatter data. It provides a description of atmospheric temperature, density, and composition for altitudes higher than 85 kilometers. There are coefficients in MSIS to account for yearly and daily variations, geodetic latitude and longitude, altitude, and solar activity. Variations due to magnetic storms are represented by three-hour magnetic ap indices. The MSIS model enables a more timely prediction of aeronomic densities for specific events, such as rocket flights. The database for this model is a comprehensive summary of rocket flight, satellite, incoherent scatter radar, grenade, and falling sphere measurements. Subsets of data were formed by random selection after sorting on altitude, latitude, time of day, etc. Curve fitting was done with four to five thousand data points at a time. The resulting coefficients are presented in subroutines which calculate thermospheric composition and temperature for a user-supplied position and time. MSIS is written in FORTRAN 77 for use with batch or interactive programs and has been implemented on a DEC VAX series computer operating under VMS 4.3 with a central memory requirement of approximately 25K of 8 bit bytes. MSIS is based on a 1977 thermosphere model and was last updated in 1987 to reflect the CIRA 1986 Neutral Thermosphere Model.

Description: This theoretical aerodynamics program, TAD, was developed to predict the aerodynamic characteristics of vehicles with sounding rocket configurations. These slender, axisymmetric finned vehicle configurations have a wide range of aeronautical applications from rockets to high speed armament. Over a given range of Mach numbers, TAD will compute the normal force coefficient derivative, the center-of-pressure, the roll forcing moment coefficient derivative, the roll damping moment coefficient derivative, and the pitch damping moment coefficient derivative of a sounding rocket configured vehicle. The vehicle may consist of a sharp pointed nose of cone or tangent ogive shape, up to nine other body divisions of conical shoulder, conical boattail, or circular cylinder shape, and fins of trapezoid planform shape with constant cross section and either three or four fins per fin set. The characteristics computed by TAD have been shown to be accurate to within ten percent of experimental data in the supersonic region. The TAD program calculates the characteristics of separate portions of the vehicle, calculates the interference between separate portions of the vehicle, and then combines the results to form a total vehicle solution. Also, TAD can be used to calculate the characteristics of the body or fins separately as an aid in the design process. Input to the TAD program consists of simple descriptions of the body and fin geometries and the Mach range of interest. Output includes the aerodynamic characteristics of the total vehicle, or user-selected portions, at specified points over the mach range. The TAD program is written in FORTRAN IV for batch execution and has been implemented on an IBM 360 computer with a central memory requirement of approximately 123K of 8 bit bytes. The TAD program was originally developed in 1967 and last updated in 1972.

Description: This program, which is called 'AOFA', determines the complete viscous and inviscid flow around a body of revolution at a given angle of attack and traveling at supersonic speeds. The viscous calculations from this program agree with experimental values for surface and pitot pressures and with surface heating rates. At high speeds, lee-side flows are important because the local heating is difficult to correlate and because the shed vortices can interact with vehicle components such as a canopy or a vertical tail. This program should find application in the design analysis of any high speed vehicle. Lee-side flows are difficult to calculate because thin-boundary-layer theory is not applicable and the concept of matching inviscid and viscous flow is questionable. This program uses the parabolic approximation to the compressible Navier-Stokes equations and solves for the complete inviscid and viscous regions of flow, including the pressure. The parabolic approximation results from the assumption that the stress derivatives in the streamwise direction are small in comparison with derivatives in the normal and circumferential directions. This assumption permits the equation to be solved by an implicit finite difference marching technique which proceeds downstream from the initial data point, provided the inviscid portion of flow is supersonic. The viscous cross-flow separation is also determined as part of the solution. To use this method it is necessary to first determine an initial data point in a region where the inviscid portion of the flow is supersonic. Input to this program consists of two parts. Problem description is conveyed to the program by namelist input. Initial data is acquired by the program as formatted data. Because of the large amount of run time this program can consume the program includes a restart capability. Output is in printed format and magnetic tape for further processing. This program is written in FORTRAN IV and has been implemented on a CDC 7600 with a central memory requirement of approximately 35K (octal) of 60 bit words.

Description: The Comprehensive Analytical Model of Rotorcraft Aerodynamics, CAMRAD, program is designed to calculate rotor performance, loads, and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. The analysis is a consistent combination of structural, inertial, and aerodynamic models applicable to a wide range of problems and a wide class of vehicles. The CAMRAD analysis can be applied to articulated, hingeless, gimballed, and teetering rotors with an arbitrary number of blades. The rotor degrees of freedom included are blade/flap bending, rigid pitch and elastic torsion, and optionally gimbal or teeter motion. General two-rotor aircrafts can be modeled. Single main-rotor and tandem helicopter and sideby-side tilting proprotor aircraft configurations can be considered. The case of a rotor or helicopter in a wind tunnel can also be modeled. The aircraft degrees of freedom included are the six rigid body motion, elastic airframe motions, and the rotor/engine speed perturbations. CAMRAD calculates the load and motion of helicopters and airframes in two stages. First the trim solution is obtained; then the flutter, flight dynamics, and/or transient behavior can be calculated. The trim operating conditions considered include level flight, steady climb or descent, and steady turns. The analysis of the rotor includes nonlinear inertial and aerodynamic models, applicable to large blade angles and a high inflow ratio, The rotor aerodynamic model is based on two-dimensional steady airfoil characteristics with corrections for three-dimensional and unsteady flow effects, including a dynamic stall model. In the flutter analysis, the matrices are constructed that describe the linear differential equations of motion, and the equations are analyzed. In the flight dynamics analysis, the stability derivatives are calculated and the matrices are constructed that describe the linear differential equations of motion. These equations are analyzed. In the transient analysis, the rigid body equations of motion are numerically integrated, for a prescribed transient gust or control input. The CAMRAD program product is available by license for a period of ten years to domestic U.S. licensees. The licensed program product includes the CAMRAD source code, command procedures, sample applications, and one set of supporting documentation. Copies of the documentation may be purchased separately at the price indicated below. CAMRAD is written in FORTRAN 77 for the DEC VAX under VMS 4.6 with a recommended core memory of 4.04 megabytes. The DISSPLA package is necessary for graphical output. CAMRAD was developed in 1980.

Description: ARC2D is a computational fluid dynamics program developed at the NASA Ames Research Center specifically for airfoil computations. The program uses implicit finite-difference techniques to solve two-dimensional Euler equations and thin layer Navier-Stokes equations. It is based on the Beam and Warming implicit approximate factorization algorithm in generalized coordinates. The methods are either time accurate or accelerated non-time accurate steady state schemes. The evolution of the solution through time is physically realistic; good solution accuracy is dependent on mesh spacing and boundary conditions. The mathematical development of ARC2D begins with the strong conservation law form of the two-dimensional Navier-Stokes equations in Cartesian coordinates, which admits shock capturing. The Navier-Stokes equations can be transformed from Cartesian coordinates to generalized curvilinear coordinates in a manner that permits one computational code to serve a wide variety of physical geometries and grid systems. ARC2D includes an algebraic mixing length model to approximate the effect of turbulence. In cases of high Reynolds number viscous flows, thin layer approximation can be applied. ARC2D allows for a variety of solutions to stability boundaries, such as those encountered in flows with shocks. The user has considerable flexibility in assigning geometry and developing grid patterns, as well as in assigning boundary conditions. However, the ARC2D model is most appropriate for attached and mildly separated boundary layers; no attempt is made to model wake regions and widely separated flows. The techniques have been successfully used for a variety of inviscid and viscous flowfield calculations. The Cray version of ARC2D is written in FORTRAN 77 for use on Cray series computers and requires approximately 5Mb memory. The program is fully vectorized. The tape includes variations for the COS and UNICOS operating systems. Also included is a sample routine for CONVEX computers to emulate Cray system time calls, which should be easy to modify for other machines as well. The standard distribution media for this version is a 9-track 1600 BPI ASCII Card Image format magnetic tape. The Cray version was developed in 1987. The IBM ES/3090 version is an IBM port of the Cray version. It is written in IBM VS FORTRAN and has the capability of executing in both vector and parallel modes on the MVS/XA operating system and in vector mode on the VM/XA operating system. Various options of the IBM VS FORTRAN compiler provide new features for the ES/3090 version, including 64-bit arithmetic and up to 2 GB of virtual addressability. The IBM ES/3090 version is available only as a 9-track, 1600 BPI IBM IEBCOPY format magnetic tape. The IBM ES/3090 version was developed in 1989. The DEC RISC ULTRIX version is a DEC port of the Cray version. It is written in FORTRAN 77 for RISC-based Digital Equipment platforms. The memory requirement is approximately 7Mb of main memory. It is available in UNIX tar format on TK50 tape cartridge. The port to DEC RISC ULTRIX was done in 1990. COS and UNICOS are trademarks and Cray is a registered trademark of Cray Research, Inc. IBM, ES/3090, VS FORTRAN, MVS/XA, and VM/XA are registered trademarks of International Business Machines. DEC and ULTRIX are registered trademarks of Digital Equipment Corporation.

Description: Panel methods are moderate cost tools for solving a wide range of engineering problems. PMARC (Panel Method Ames Research Center) is a potential flow panel code that numerically predicts flow fields around complex three-dimensional geometries. PMARC's predecessor was a panel code named VSAERO which was developed for NASA by Analytical Methods, Inc. PMARC is a new program with many additional subroutines and a well-documented code suitable for powered-lift aerodynamic predictions. The program's open architecture facilitates modifications or additions of new features. Another improvement is the adjustable size code which allows for an optimum match between the computer hardware available to the user and the size of the problem being solved. PMARC can be resized (the maximum number of panels can be changed) in a matter of minutes. Several other state-of-the-art PMARC features include internal flow modeling for ducts and wind tunnel test sections, simple jet plume modeling essential for the analysis and design of powered-lift aircraft, and a time-stepping wake model which allows the study of both steady and unsteady motions. PMARC is a low-order panel method, which means the singularities are distributed with constant strength over each panel. In many cases low-order methods can provide nearly the same accuracy as higher order methods (where the singularities are allowed to vary linearly or quadratically over each panel). Low-order methods have the advantage of a shorter computation time and do not require exact matching between panels. The flow problem is solved by assuming that the body is at rest in a moving flow field. The body is modeled as a closed surface which divides space into two regions -- one region contains the flow field of interest and the other contains a fictitious flow. External flow problems, such as a wing in a uniform stream, have the external region as the flow field of interest and the internal flow as the fictitious flow. This arrangement is reversed for internal flow problems where the internal region contains the flow field of interest and the external flow field is fictitious. In either case it is assumed that the velocity potentials in both regions satisfy Laplace's equation. PMARC has extensive geometry modeling capabilities for handling complex, three-dimensional surfaces. As with all panel methods, the geometry must be modeled by a set of panels. For convenience, the geometry is usually subdivided into several pieces and modeled with sets of panels called patches. A patch may be folded over on itself so that opposing sides of the patch form a common line. For example, wings are normally modeled with a folded patch to form the trailing edge of the wing. PMARC also has the capability to automatically generate a closing tip patch. In the case of a wing, a tip patch could be generated to close off the wing's third side. PMARC has a simple jet model for simulating a jet plume in a crossflow. The jet plume shape, trajectory, and entrainment velocities are computed using the Adler/Baron jet in crossflow code. This information is then passed back to PMARC. The wake model in PMARC is a time-stepping wake model. The wake is convected downstream from the wake separation line by the local velocity flowfield. With each time step, a new row of wake panels is added to the wake at the wake separation line. PMARC also allows an initial wake to be specified if desired, or, as a third option, no wakes need be modeled. The effective presentation of results for aerodynamics problems requires the generation of report-quality graphics. PMAPP (ARC-12751), the Panel Method Aerodynamic Plotting Program, (Sterling Software), was written for scientists at NASA's Ames Research Center to plot the aerodynamic analysis results (flow data) from PMARC. PMAPP is an interactive, color-capable graphics program for the DEC VAX or MicroVAX running VMS. It was designed to work with a variety of terminal types and hardcopy devices. PMAPP is available separately from COSMIC. PMARC was written in standard FORTRAN77 using adjustable size arrays throughout the code. Redimensioning PMARC will change the amount of disk space and memory the code requires to be able to run; however, due to its memory requirements, this program does not readily lend itself to implementation on MS-DOS based machines. The program was implemented on an Apple Macintosh (using 2.5 MB of memory) and tested on a VAX/VMS computer. The program is available on a 3.5 inch Macintosh format diskette (standard media) or in VAX BACKUP format on TK50 tape cartridge or 9-track magnetic tape. PMARC was developed in 1989.

Description: The Transonic Airfoil analysis computer code, TAIR, was developed to employ a fast, fully implicit algorithm to solve the conservative full-potential equation for the steady transonic flow field about an arbitrary airfoil immersed in a subsonic free stream. The full-potential formulation is considered exact under the assumptions of irrotational, isentropic, and inviscid flow. These assumptions are valid for a wide range of practical transonic flows typical of modern aircraft cruise conditions. The primary features of TAIR include: a new fully implicit iteration scheme which is typically many times faster than classical successive line overrelaxation algorithms; a new, reliable artifical density spatial differencing scheme treating the conservative form of the full-potential equation; and a numerical mapping procedure capable of generating curvilinear, body-fitted finite-difference grids about arbitrary airfoil geometries. Three aspects emphasized during the development of the TAIR code were reliability, simplicity, and speed. The reliability of TAIR comes from two sources: the new algorithm employed and the implementation of effective convergence monitoring logic. TAIR achieves ease of use by employing a "default mode" that greatly simplifies code operation, especially by inexperienced users, and many useful options including: several airfoil-geometry input options, flexible user controls over program output, and a multiple solution capability. The speed of the TAIR code is attributed to the new algorithm and the manner in which it has been implemented. Input to the TAIR program consists of airfoil coordinates, aerodynamic and flow-field convergence parameters, and geometric and grid convergence parameters. The airfoil coordinates for many airfoil shapes can be generated in TAIR from just a few input parameters. Most of the other input parameters have default values which allow the user to run an analysis in the default mode by specifing only a few input parameters. Output from TAIR may include aerodynamic coefficients, the airfoil surface solution, convergence histories, and printer plots of Mach number and density contour maps. The TAIR program is written in FORTRAN IV for batch execution and has been implemented on a CDC 7600 computer with a central memory requirement of approximately 155K (octal) of 60 bit words. The TAIR program was developed in 1981.

Description: The TAWFIVE program calculates transonic flow over a transport-type wing and fuselage. Although more complex Euler and Navier-Stokes methods are available, TAWFIVE combines a multi-grid acceleration technique in the iterative solution of the potential equation with the use of integral-form boundary-layer equations to provide a computationally efficient and sufficiently accurate design tool. TAWFIVE simplifies the solution process by breaking the problem into a loosely coupled set of modified equations. The inviscid method, using standard inviscid equations (nonlinear full potential), is valid in the "outer" region away from the wing, whereas the boundary-layer equations are valid in the thin region near the solid surface of the wing. The two types of equations are coupled by a technique of modifying surface boundary conditions for the inviscid equations. This interaction process starts with a solution of the outer flow field. Pressures are computed at the wing surface and are used to calculate the boundary layer. The boundary-layer and wake properties are then computed using a three-dimensional integral method, and the computed displacement thickness is added to the surface of the "hard" geometry. This new displaced wing surface is then regridded and the inviscid flowfield is recomputed. New values of the inviscid pressures are then used by the boundary-layer method to predict a new displacement thickness distribution. An under-relaxed update of the previously predicted displacement thickness is then made to obtain a new displacement thickness correction that is added to the "hard" geometry. These global iterations are continued until suitable convergence is obtained. Input to TAWFIVE is limited to geometric definition of the configuration, free-stream flow quantities, and iteration control parameters. The geometric input consists of the definition of a series of airfoil sections to define the wing and a series of fuselage cross sections to model the fuselage. High-aspect-ratio wings are modeled more accurately than low-aspect-ratio wings since no special provisions are made to accurately model the wing-fuselage juncture or the wingtip region. The user can specify the solution either in terms of lift or in terms of angle of attack. TAWFIVE can produce tabular output and input files for PLOT3D (COSMIC program number ARC-12779). TAWFIVE is written in FORTRAN 77 for CRAY series computers running UNICOS. The main memory requirement is 2.7Mb for execution. This program is available on a 9-track 1600 BPI UNIX tar format magnetic tape. TAWFIVE was under development from 1979 to 1989 and first released by COSMIC in 1991. CRAY and UNICOS are registered trademarks of Cray Research, Inc.

Description: A summary is presented of vortex control applications and current techniques for the control of longitudinal vortices produced by bodies, leading edges, tips and intersections. Vortex control has up till now been performed by many approaches in an empirical fashion, assisted by the essentially inviscid nature of much of longitudinal vortex behavior. Attention is given to Reynolds number sensitivities, vortex breakdown and interactions, vortex control on highly swept wings, and vortex control in juncture flows.

Description: On an hourly time-scale the different roles of the solar wind and interplanetary magnetic field (IMF) parameters on ground micropulsation activity can be better investigated than at longer time-scales. A long-term comparison between ground measurements made at L'Aquila and IMP 8 observations confirms the solar wind speed as the key parameter for the onset of pulsations even at low latitudes, although additional control of the energy transfer from the interplanetary medium to the earth's magnetosphere is clearly exerted by the cone angle. Above about 20 mHz the frequency of pulsations is confirmed to be closely related to the IMF magnitude while, in agreement with model predictions, the IMF magnitude is related to the amplitude of the local fundamental resonant mode. We provide an interesting example in which high resolution measurements simultaneously obtained in the foreshock region and on the ground show that external transversal fluctuations do not penetrate deep into the low latitude magnetosphere.

Description: This paper discusses in situ measurements of O3, aerosol number density, and aerosol size obtained during NASA Arctic Boundary Layer Expedition aircraft flights over the Alaskan Arctic region. The major source of summer O3 for the troposphere in the intrusion of stratospheric air and subsequent transport to lower altitudes. Photochemistry of mixed layer emissions and O3 transported from high northern latitude urban/industrialized areas do not appear to play major roles as sources of O3 for the Alaska region. O3 gradients reflect the loss at the surface and supply from the stratosphere. Free tropospheric O3 averaged 74 ppbv compared to 32 ppbv for the mixed layer. O3 loss mechanisms are a combination of the destruction via photochemistry, chemical reaction with surface emissions, and direct loss through deposition to the surface. The boreal forest in the most efficient of the O3 sinks and has the largest increase in aerosol number density relative to the free troposphere.

Description: The flow-field within an axial flow turbomachine, such as a turbine or compressor, is extremely complex because of three-dimensional features such as hub-corner stall, tip-leakage flows, and airfoil wakes. These flow features interact with each other and with rotor and stator airfoils inducing time-varying forces on the airfoils. These complicated rotor-stator interactions must be understood in order to design turbomachines that are light and compact as well as reliable and efficient. Two codes, STAGE-2 and STAGE-3, have been developed to compute these unsteady rotor-stator interaction flows in multistage turbomachines. An implicit, thin-layer Euler/Navier-Stokes zonal algorithm is used to compute the unsteady flow-field within both turbine and compressor configurations. Results include surface pressures and wake profiles for two-dimensional turbine and compressor configurations and surface pressures for a three-dimensional single-stage turbine configuration. The results compare well with experimental data and other unsteady computations.

Description: The most important investigations leading to the International Reference Ionosphere 1990 (IRI-90) are overviewed, and the latest version of the model is described. The shortcomings and limitations of the IRI-90 are pointed out, together with the ways of overcoming them. The list of studies that the IRI group has yet to carry out includes the investigations of magnetic storm effects as the highest priority. This paper discusses determinations of and the available data on the electron density, plasma temperatures, ion composition, and ion drift in the ionosphere, together with future improvements needed on these parameters.

Description: In the aftermath of the eruption of Mt. Pinatubo, multiwavelength stratospheric aerosol extinction measurements by the satellite-borne Stratospheric Aerosol and Gas Experiment (SAGE II) revealed the presence of a previously unobserved mode of aerosol that exhibited high extinction but a small inferred particle size. This mode may represent a transitional phase between the very small aerosol created by gas-to-particle conversion and a quasi-steady state, post-volcanic aerosol that exhibits both large extinction and large particle size. The presence of a transitional small aerosol mode may have a significant impact on chemical and radiative processes in the stratosphere.

Description: CO2 exchange rates were measured at selected tundra sites near Bethel, Alaska using portable, climate-controlled, instrumented enclosures. The empirically modeled exchange rate for a representative area of vegetated tundra was 1.2 +/- 1.2 g/sq m/d, compared to a tower-measured exchange over the same time period of 1.1 +.0- 1.2 g/sq m/d. Net exchange in response to varying light levels was compared to wet meadow and dry upland tundra, and to the net exchange measured by the micrometeoroidal tower technique. The multispectral reflectance properties of the sites were measured and related to exchange rates in order to provide a quantitative foundation for the use of satellite remote sensing to monitor biosphere/atmosphere CO2 exchange in the tundra biome.

Description: Enhanced concentrations of CH4 in the unpolluted atmospheric mixed layer over both Arctic and subarctic tundra landscapes are documented here using data from the NASA Arctic Boundary Layer Expedition (ABLE 3A). The CH4 concentration gradients were determined mainly by interactions of biogenic emission from wet tundra and turbulent mixing proceses. The gradient were most frequently associated with intrusion of upper tropospheric or stratospheric air into the midtroposphere, emissions from forest and tundra fires, and long-range transport of enhanced concentration of these gases from unidentified sources. Summertime haze layers exhibited midtropospheric enhancements of CH4 similar to those measured in winter Arctic events. The observations confirm the importance of Arctic and Subarctic wetland environments as a regional source of global atmospheric CH4.

Description: The oxidation of the earth's crust and the increase in atmospheric oxygen early in earth history have been linked to the accumulation of reduced carbon in sedimentary rocks. Trends in the carbon isotope composition of sedimentary organic carbon and carbonate show that during the Proterozoic aeon (2.5-0.54 Gyr ago) the organic carbon reservoir grew in size, relative to the carbonate reservoir. This increase, and the concomitant release of oxidizing power in the environment, occurred mostly during episodes of global rifting and orogeny.

Description: Recently available spectral O3 line parameters are summarized and progress in remote sensing based on these parameters is discussed. Particular attention is given to covering line positions, line intensities and linewidths for both the main isotopic species (O-16)3 and the isotopic variants (O-16)(O-18)(O-16) and (O-16)(O-16)(O-18).

Description: Jet noise and jet-induced structural loads have become key issues in the design of commercial and military aircraft. Computational Fluid Dynamics (CFD) can be of use in predicting the underlying jet shear-layer instabilities and, in conjunction with classical acoustic theory, jet noise. The computational issues involved in the resolution of high Reynolds number unsteady jet flows are addressed in this paper. Once these jet flows can be accurately resolved, it should be possible to use acoustic theory to extract, for example, the far-field jet noise. An assessment of future work and computational resources required for directly computing far-field jet noise is also presented.

Description: The paper presents Alouette 2/ISIS 1 data which furnish evidence for the stimulation of high-order D(n) resonances (n greater than 4) by topside sounders, confirming the prediction of Osherovich (1990) based on an analogy with naturally occurring narrowband magnetospheric emissions. The results indicate that observations of stimulated ionospheric emissions and naturally occurring magnetospheric emissions can be used as complementary data sets to address such fundamental questions as the nature of the excitation mechanism for these emissions and the nature of the waves (i.e., whether the waves predominantly electrostatic or with a significant magnetic component present), and the question of the dominance among the Dn, Dn(+), and Dn(-) resonances and the conditions required for all three to be present at the same time.

Description: Ground magnetic field perturbations recorded by the CANOPUS magnetometer network in the 7 to 13 MLT sector are used to examine how reconfigurations of the dayside polar ionospheric flow take place in response to north-south changes of the IMF. During the 6-h interval in question, IMF Bz oscillates between +/- 7 nT with about a 1-h period. Corresponding variations in the ground magnetic disturbance are observed which we infer are due to changes in ionospheric flow. Cross correlation of the data obtained from two ground stations at 73.5 deg magnetic latitude, but separated by about 2 hours in MLT, shows that changes in the flow are initiated in the prenoon sector (about 10 MLT) and then spread outward toward dawn and dusk with a phase speed of about 5 km/s over the longitude range about 8 to 12 MLT, slowing to about 2 km/s outside this range. Cross correlating the data from these ground stations with IMP 8 IMF Bz records produces a MLT variation in the ground response delay relative to the IMF which is compatible with these deduced phase speeds.

Description: The particle scattering and current sheet stability features in the geomagnetic tail during the phase of substorm growth were investigated using Tsyganenko's (1989) magnetic field model. In a study of four substorm events which were observed both in the high-altitude nightside tail and in the auroral ionosphere, the model magnetic field was adjusted to each case so as to represent the global field development during the growth phase of the substorms. The model results suggest that the auroral brightenings are connected with processes taking place in the near-earth region inside about 15 earth radii. The results also suggest that there is a connection between the chaotization of the electrons and the auroral brightenings at substorm onset.

Description: Alternative geometries for the present-day configuration of plate boundaries in northeast Asia and Japan are tested using NUVEL-1 and 256 horizontal earthquake slip vectors from the Japan and northern Kuril trenches. Statistical analysis of the slip vectors is used to determine whether the North American, Eurasian, or Okhotsk plate overlies the trench. Along the northern Kuril trench, slip vectors are well-fit by the NUVEL-1 Pacific-North America Euler pole, but are poorly fit by the Pacific-Eurasia Euler pole. Results for the Japan trench are less conclusive, but suggest that much of Honshu and Hokkaido are also part of the North American plate. The simplest geometry consistent with the trench slip vectors is a geometry in which the North American plate extends south to 41 deg N, and possibly includes northern Honshu and southern Hokkaido. Although these results imply that the diffuse seismicity that connects the Lena River delta to Sakhalin Island and the eastern Sea of Japan records motion between Eurasia and North America, onshore geologic and seismic data define an additional belt of seismicity in Siberia that cannot be explained with this geometry. Assuming that these two seismic belts constitute evidence for an Okhotsk block, two published kinematic models for motion of the Okhotsk block are tested. The first model, which predicts motion of up to 15 mm/yr relative to North America, is rejected because Kuril and Japan trench slip vectors are fit more poorly than for the simpler geometry described above. The second model gives a good fit to the trench slip vectors, but only if Okhotsk-North America motion is slower than 5 mm/yr.

Description: This computer program is designed to calculate the flow fields in two-dimensional and three-dimensional axisymmetric supersonic inlets. The method of characteristics is used to compute arrays of points in the flow field. At each point the total pressure, local Mach number, local flow angle, and static pressure are calculated. This program can be used to design and analyze supersonic inlets by determining the surface compression rates and throat flow properties. The program employs the method of characteristics for a perfect gas. The basic equation used in the program is the compatibility equation which relates the change in stream angle to the change in entropy and the change in velocity. In order to facilitate the computation, the flow field behind the bow shock wave is broken into regions bounded by shock waves. In each region successive rays are computed from a surface to a shock wave until the shock wave intersects a surface or falls outside the cowl lip. As soon as the intersection occurs a new region is started and the previous region continued only in the area in which it is needed, thus eliminating unnecessary calculations. The maximum number of regions possible in the program is ten, which allows for the simultaneous calculations of up to nine shock waves. Input to this program consists of surface contours, free-stream Mach number, and various calculation control parameters. Output consists of printed and/or plotted results. For plotted results an SC-4020 or similar plotting device is required. This program is written in FORTRAN IV to be executed in the batch mode and has been implemented on a CDC 7600 with a central memory requirement of approximately 27k (octal) of 60 bit words.

Description: This program was developed to predict turbine stage performance taking into account the effects of complex passage geometries. The method uses a quasi-3D inviscid-flow analysis iteratively coupled to calculated losses so that changes in losses result in changes in the flow distribution. In this manner the effects of both the geometry on the flow distribution and the flow distribution on losses are accounted for. The flow may be subsonic or shock-free transonic. The blade row may be fixed or rotating, and the blades may be twisted and leaned. This program has been applied to axial and radial turbines, and is helpful in the analysis of mixed flow machines. This program is a combination of the flow analysis programs MERIDL and TSONIC coupled to the boundary layer program BLAYER. The subsonic flow solution is obtained by a finite difference, stream function analysis. Transonic blade-to-blade solutions are obtained using information from the finite difference, stream function solution with a reduced flow factor. Upstream and downstream flow variables may vary from hub to shroud and provision is made to correct for loss of stagnation pressure. Boundary layer analyses are made to determine profile and end-wall friction losses. Empirical loss models are used to account for incidence, secondary flow, disc windage, and clearance losses. The total losses are then used to calculate stator, rotor, and stage efficiency. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370/3033 under TSS with a central memory requirement of approximately 4.5 Megs of 8 bit bytes. This program was developed in 1985.

Description: Turbomachinery components are often connected by ducts, which are usually annular. The configurations and aerodynamic characteristics of these ducts are crucial to the optimum performance of the turbomachinery blade rows. The ANDUCT computer program was developed to calculate the velocity distribution along an arbitrary line between the inner and outer walls of an annular duct with axisymmetric swirling flow. Although other programs are available for duct analysis, the use of the velocity gradient method makes the ANDUCT program fast and convenient while requiring only modest computer resources. A fast and easy method of analyzing the flow through a duct with axisymmetric flow is the velocity gradient method, also known as the stream filament or streamline curvature method. This method has been used extensively for blade passages but has not been widely used for ducts, except for the radial equilibrium equation. In ANDUCT, a velocity gradient equation derived from the momentum equation is used to determine the velocity variation along an arbitrary straight line between the inner and outer wall of an annular duct. The velocity gradient equation is used with an assumed variation of meridional streamline curvature. Upstream flow conditions may vary between the inner and outer walls, and an assumed total pressure distribution may be specified. ANDUCT works best for well-guided passages and where the curvature of the walls is small as compared to the width of the passage. The ANDUCT program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 60K of 8 bit bytes. The ANDUCT program was developed in 1982.

Description: The Panel Code for Planar Cascades was developed as an aid for the designer of turbomachinery blade rows. The effective design of turbomachinery blade rows relies on the use of computer codes to model the flow on blade-to-blade surfaces. Most of the currently used codes model the flow as inviscid, irrotational, and compressible with solutions being obtained by finite difference or finite element numerical techniques. While these codes can yield very accurate solutions, they usually require an experienced user to manipulate input data and control parameters. Also, they often limit a designer in the types of blade geometries, cascade configurations, and flow conditions that can be considered. The Panel Code for Planar Cascades accelerates the design process and gives the designer more freedom in developing blade shapes by offering a simple blade-to-blade flow code. Panel, or integral equation, solution techniques have been used for several years by external aerodynamicists who have developed and refined them into a primary design tool of the aircraft industry. The Panel Code for Planar Cascades adapts these same techniques to provide a versatile, stable, and efficient calculation scheme for internal flow. The code calculates the compressible, inviscid, irrotational flow through a planar cascade of arbitrary blade shapes. Since the panel solution technique is for incompressible flow, a compressibility correction is introduced to account for compressible flow effects. The analysis is limited to flow conditions in the subsonic and shock-free transonic range. Input to the code consists of inlet flow conditions, blade geometry data, and simple control parameters. Output includes flow parameters at selected control points. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 590K of 8 bit bytes. This program was developed in 1982.

Description: An exact, full-potential-equation model for the steady, irrotational, homoentropic, and homoenergetic flow of a compressible, inviscid fluid through a two-dimensional planar cascade together with its appropriate boundary conditions has been derived. The CAS2D computer program numerically solves an artificially time-dependent form of the actual full-potential-equation, providing a nonrotating blade-to-blade, steady, potential transonic cascade flow analysis code. Comparisons of results with test data and theoretical solutions indicate very good agreement. In CAS2D, the governing equation is discretized by using type-dependent, rotated finite differencing and the finite area technique. The flow field is discretized by providing a boundary-fitted, nonuniform computational mesh. This mesh is generated by using a sequence of conformal mapping, nonorthogonal coordinate stretching, and local, isoparametric, bilinear mapping functions. The discretized form of the full-potential equation is solved iteratively by using successive line over relaxation. Possible isentropic shocks are captured by the explicit addition of an artificial viscosity in a conservative form. In addition, a four-level, consecutive, mesh refinement feature makes CAS2D a reliable and fast algorithm for the analysis of transonic, two-dimensional cascade flows. The results from CAS2D are not directly applicable to three-dimensional, potential, rotating flows through a cascade of blades because CAS2D does not consider the effects of the Coriolis force that would be present in the three-dimensional case. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 200K of 8 bit bytes. The CAS2D program was developed in 1980.

Description: A computer program, QSONIC, has been developed for calculating the full potential, transonic quasi-three-dimensional flow through a rotating turbomachinery blade row. The need for lighter, more efficient turbomachinery components has led to the consideration of machines with fewer stages, each with blades capable of higher speeds and higher loading. As speeds increase, the numerical problems inherent in the transonic regime have to be resolved. These problems include the calculation of imbedded shock discontinuities and the dual nature of the governing equations, which are elliptic in the subcritical flow regions but become hyperbolic for supersonic zones. QSONIC provides the flow analyst with a fast and reliable means of obtaining the transonic potential flow distribution on a blade-to-blade stream surface of a stationary or rotating turbomachine blade row. QSONIC combines several promising transonic analysis techniques. The full potential equation in conservative form is discretized at each point on a body-fitted period mesh. A mass balance is calculated through the finite volume surrounding each point. Each local volume is corrected in the third dimension for any change in stream-tube thickness along the stream tube. The nonlinear equations for all volumes are of mixed type (elliptic or hyperbolic) depending on the local Mach number. The final result is a block-tridiagonal matrix formulation involving potential corrections at each grid point as the unknowns. The residual of each system of equations is solved along each grid line. At points where the Mach number exceeds unity, the density at the forward (sweeping) edge of the volume is replaced by an artificial density. This method calculates the flow field about a cascade of arbitrary two-dimensional airfoils. Three-dimensional flow is approximated in a turbomachinery blade row by correcting for stream-tube convergence and radius change in the through flow direction. Several significant assumptions were made in developing the QSONIC program, including: (1) the flow is inviscid and adiabatic, (2) the flow relative to the blade is steady, (3) the fluid is a perfect gas with constant specific heat, (4) the flow is isentropic and any discontinuities (shocks) are weak enough to be approximated as isentropic jumps, (5) there is no velocity component normal to the stream surface, and (6) the flow relative to a fixed frame in space (absolute velocity) is completely irrotational. These assumptions place some limitations on the application of QSONIC. Sharp leading edges at high incidence and high-Mach-number turbine blade trailing edges with substantial deviation will both cause large velocity peaks on the blade. In addition, the program may have difficulty converging if the passage is nearly choked. Input to QSONIC consists of case control parameters, a geometry description, upstream boundary conditions, and a rotor description. Output includes solution scheme parameters and flow field parameters. A data file is also output which contains data on the solution mesh, surface Mach numbers, surface static pressures, isomachs, and the velocity vector field. This data may be used for further processing or for plotting. The QSONIC is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 500K of 8 bit bytes. QSONIC was developed in 1982.

Description: This computer program, WIND, was developed to numerically solve the exact, full-potential equation for three-dimensional, steady, inviscid flow through an isolated wind turbine rotor. The program automatically generates a three-dimensional, boundary-conforming grid and iteratively solves the full-potential equation while fully accounting for both the rotating and Coriolis effects. WIND is capable of numerically analyzing the flow field about a given blade shape of the horizontal-axis type wind turbine. The rotor hub is assumed representable by a doubly infinite circular cylinder. An arbitrary number of blades may be attached to the hub and these blades may have arbitrary spanwise distributions of taper and of the twist, sweep, and dihedral angles. An arbitrary number of different airfoil section shapes may be used along the span as long as the spanwise variation of all the geometeric parameters is reasonably smooth. The numerical techniques employed in WIND involve rotated, type-dependent finite differencing, a finite volume method, artificial viscosity in conservative form, and a successive overrelaxation combined with the sequential grid refinement procedure to accelerate the iterative convergence rate. Consequently, WIND is cabable of accurately analyzing incompressible and compressible flows, including those that are locally transonic and terminated by weak shocks. Along with the three-dimensional results, WIND provides the results of the two-dimensional calculations to aid the user in locating areas of possible improvement in the aerodynamic design of the blade. Output from WIND includes the chordwise distribution of the coefficient of pressure, the Mach number, the density, and the relative velocity components at spanwise stations along the blade. In addition, the results specify local values of the lift coefficient and the tangent and axial aerodynamic force components. These are also given in integrated form expressing the total torque and the total axial force acting on the shaft. WIND can also be used to analyze the flow around isolated aircraft propellers and helicopter rotors in hover as long as the relative oncoming flow is subsonic. The WIND program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370 series computer with a central memory requirement of approximately 253K of 8 bit bytes. WIND was developed in 1980.

Description: This computer program calculates the flow field in the supersonic portion of a mixed-compression aircraft inlet at non-zero angle of attack. This approach is based on the method of characteristics for steady three-dimensional flow. The results of this program agree with those produced by the two-dimensional method of characteristics when axisymmetric flow fields are calculated. Except in regions of high viscous interaction and boundary layer removal, the results agree well with experimental data obtained for threedimensional flow fields. The flow field in a variety of axisymmetric mixed compression inlets can be calculated using this program. The bow shock wave and the internal shock wave system are calculated using a discrete shock wave fitting procedure. The internal flow field can be calculated either with or without the discrete fitting of the internal shock wave system. The influence of molecular transport can be included in the calculation of the external flow about the forebody and in the calculation of the internal flow when internal shock waves are not discretely fitted. The viscous and thermal diffussion effects are included by treating them as correction terms in the method of characteristics procedure. Dynamic viscosity is represented by Sutherland's law and thermal conductivity is represented as a quadratic function of temperature. The thermodynamic model used is that of a thermally and calorically perfect gas. The program assumes that the cowl lip is contained in a constant plane and that the centerbody contour and cowl contour are smooth and have continuous first partial derivatives. This program cannot calculate subsonic flow, the external flow field if the bow shock wave does not exist entirely around the forebody, or the internal flow field if the bow flow field is injected into the annulus. Input to the program consists of parameters to control execution, to define the geometry, and the vehicle orientation. Output consists of a list of parameters used, solution planes, and a description of the shock waves. This program is written in FORTRAN IV for batch execution and has been implemented on a CDC 6000 series machine with a central memory requirement of 110K (octal) of 60 bit words when it is overlayed. This flow analysis program was developed in 1978.