ALBERT

Description: The International Cometary Explorer (ICE) encounter with Comet Giacobini-Zinner took place 7 years after the spacecraft's original launch on 12 August 1978 as the International Sun Earth Explorer 3 (ISEE-3), part of a three-spacecraft project to study the interaction between the solar wind and the Earth's magnetosphere. Transfer to an interplanetary trajectory was performed via a 119-km-altitute, gravity-assist, lunar swingby on December 1983. Navigation support during interplanetary cruise and comet encounter was provided by orbit determination utilizing radio metric data from the DSN 64-meter antennas in Goldstone, California and Madrid, Spain. Orbit solutions yielding predictions of 50-km geocentric delivery accuracy in the target aim plane were achieved during interplanetary cruise and at comet encounter using 6-to-12-week data arcs between periodic attitude-change maneuvers. One-sigma two-way range and range rate residuals were consistently 40 meters and 0.2 mm/s or better, respectively. Non-gravitational forces affected the comet's motion during late August and early September 1985 and caused a 2300-km shift in the orbit of the comet relative to the spacecraft. This necessitated a final ICE orbit trim maneuver 3 days prior to encounter. Near-real-time assessment of two-way 2-GHz (S-band) Doppler pseudo-residuals during the June and July 1985 trajectory change maneuvers aided in calibration of the spacecraft's thrusters in preparation for this final critical maneuver. Post-flight analysis indicates tail centerline passage was achieved within 10 seconds of the predicted time and geocentric position uncertainty at encounter was less than 40 km.

Description: The test capabilities of the Stability Wind Tunnel of the Virginia Polytechnic Institute and State University are described, and calibrations for curved and rolling flow techniques are given. Oscillatory snaking tests to determine pure yawing derivatives are considered. Representative aerodynamic data obtained for a current fighter configuration using the curved and rolling flow techniques are presented. The application of dynamic derivatives obtained in such tests to the analysis of airplane motions in general, and to high angle of attack flight conditions in particular, is discussed.

Description: Present understanding of planetary atmospheres is surveyed. The formation of the planets and their atmospheres is briefly reviewed, and attention is given to the compositions of the atmospheres of earth, Venus, and Mars, the outer planets, and Titan. Lists of the individual atmospheric gases and their concentrations are included.

Description: The discovery of concentrations of meteorites in Antarctica by Japanese field parties in 1969, and subsequently by joint U.S.-Japanese and U.S. field parties since 1976 has provided a significant new resource for understanding the origin and evolution of the solar system. The number of meteorites as well as the variety of meteorites has increased dramatically, and substantial amounts of data derived from their study has begun to appear in the scientific literature. The U.S. program of investigation has drawn on curatorial experience derived from the lunar program to: (1) develop specific collection and preliminary examination protocols; (2) provide documented samples for scientific investigations in response to specific requests; and (3) coordinate research by scientific consortia. The productivity of scientific research is significantly enhanced by these management approaches. Some of the results of the curatorial program for Antarctic meteorites carried out over the past three years are described.

Description: This design course is directed to studying problems related to mobile exploration of the surface of Mars. Constraints on the vehicles considered are set by the payload and performance currently envisioned by mission analysis carried out previously at the Jet Propulsion Laboratory. The students are given full flexibility to examine those aspects which suit their interests and background. There are no regularly scheduled class lectures. Weekly review meetings are held with personnel from the Jet Propulsion Laboratory, and students use JPL resources as required.

Description: The Moon is a body rich in natural resources and full of intriguing scientific questions, and it will most certainly play a central role in the growth of near-Earth and deep space ventures of the twenty-first century. The LOP mission is an example of one way to catalog the Moon's natural resources and to answer lunar science questions in parallel. In a realistic planetary exploration program, this mission must compete with other interesting planetary missions and therefore the LOP must be as low cost and adaptable as possible. This flexibility is reflected in the LOP's heavy design emphasis on modularity. The LOP mission can easily be expanded to include new technologies, and additional orbiters could be launched into lunar orbit to provide a constellation of remote-sensing platforms. This design thus projects a broad range of possibilities for continued lunar exploration in the next century.

Description: Opinions conflict over the role of surface gravity in shaping impact craters on Mercury. One view holds that the effects of g are evident in measurable aspects of crater form; other investigators find little or no evidence for g's geomorphic importance. Ambiguity in the role of g and other variables in cratering on Mercury stems largely from uncertainty in identifying major geomorphic contrasts and the crater sizes at which they occur. One of these, depth/diameter (d/D), undergoes a major change at the transition from simple (bowl shaped) to complex (peaks and terraces) crater interiors. Four least-squares d/D fits for fresh craters on Mercury were attemped. The results are inconsistent. The d/D data that should resolve previous shortcomings is presented. The revised d/D distributions for simple and complex craters, which intersect at a diameter of about 5 km, support the initial thesis that g substantially influences the form of Mercury's craters.

Description: Through the Surveyor 3 and 7, and Apollo 11-17 missions a knowledge of the mechanical properties of Lunar regolith were gained. These properties, including material cohesion, friction, in-situ density, grain-size distribution and shape, and porosity, were determined by indirect means of trenching, penetration, and vane shear testing. Several of these properties were shown to be significantly different from those of terrestrial soils, such as an interlocking cohesion and tensile strength formed in the absence of moisture and particle cementation. To characterize the strength and deformation properties of Lunar regolith experiments have been conducted on a lunar soil simulant at various initial densities, fabric arrangements, and composition. These experiments included conventional triaxial compression and extension, direct tension, and combined tension-shear. Experiments have been conducted at low levels of effective confining stress. External conditions such as membrane induced confining stresses, end platten friction and material self weight have been shown to have a dramatic effect on the strength properties at low levels of confining stress. The solution has been to treat these external conditions and the specimen as a full-fledged boundary value problem rather than the idealized elemental cube of mechanics. Centrifuge modeling allows for the study of Lunar soil-structure interaction problems. In recent years centrifuge modeling has become an important tool for modeling processes that are dominated by gravity and for verifying analysis procedures and studying deformation and failure modes. Centrifuge modeling is well established for terrestrial enginering and applies equally as well to Lunar engineering. A brief review of the experiments is presented in graphic and outline form.

Description: Wind tunnel model tests of rotating cylinder wing flaps and other high lift devices for STOL AIRCRAFT

Description: Linear aerodynamic load distributions on missile and launch vehicle configurations

Description: Wind tunnel testing of dorsal-fin, delta-wing and dart-wing configurations

Description: Unsteady aerodynamics studied in Saturn launch vehicle development program

Description: Turbulent fluctuation measurements with crossed beam method

Description: High speed wind tunnel study of separation phenomenon and deterioration in aerodynamic performance from unwanted flow detachments

Description: Simulators to facilitate experimental studies of two-dimensional interaction of jet with supersonic free stream

Description: Acoustic and heat transfer aspects of launch vehicle turbulence

Description: Bursting of conical vortex sheet above delta wing surface at low speeds

Description: Steady drag and unsteady lift forces on circular cylinder subjected to two-dimensional wind flow

Description: Tilt-wing V/STOL aircraft wing stall during low powered descent

Description: Dynamic responses and motion stability for hinged helicopter rotor blade at high tip speed ratios

Description: Future research areas for NASA in private airplanes, subsonic jet transport, and hypersonic flight - general discussion

Description: Aerodynamic research program on space and launch vehicle development

Description: Flow of air around delta and other swept-back wings - vortices from apex and sheets

Description: Compressor and gas turbine engine matching - power turbine, turbojet, and turboprop engines

Description: High pressure-ratio multistage axial flow compressor operation efficiency with one or more blade rows stalled - performance prediction

Description: Charts for solution of radial distribution flow equations used in axial flow compressor design

Description: General flow equations and methods used in determining radial distributions of flow in meridional plane of axial flow compressor

Description: Potential flow theory for two-dimensional cascades, and application to fluid flow through axial flow compressors

Description: Viscous effects on two-dimensional incompressible flow about compressor blade profiles in cascade

Description: Thermodynamic equations, solution, and experimental data for aerodynamic design of axial flow compressors

Description: Three-dimensional compressor flow theory and real flow effect

Description: Steady state characteristics, stalling, and surge in axial flow compressors

Description: Design and measurement error effects on compressor performance

Description: Compressor off-design performance prediction techniques

Description: Compressor data on blade-element basis for comparison with two-dimensional cascade flow data

Description: Cycle analysis of turbojet and turboprop engines - axial flow compressor requirements for gas turbine engines

Description: Aerodynamic design of axial flow compressors

Description: Secondary and three-dimensional boundary layer flows in compressor blade rows

Description: Multistage axial flow compressor stalling characteristics and blade vibration

Description: Newtonian impact flow mathematics - application to elliptic cone, conoid of biparabolic cross sections, and drop-like blunt body

Description: Quasi-slender body theory for oscillating low aspect ratio wings and bodies of revolution in supersonic flow

Description: Impulsively started steady flow and uniformly accelerated unsteady flow about circular cylinders and mathematical models

Description: Wind and water tunnel apparatus and techniques for free stream turbulent effects on time-dependent forces acting on circular cylinders

Description: Amplitude and surface pressure measurements for circular cylinder in vortex flow-excited oscillation

Description: Wind tunnel boundary interference effects on V/STOL model aircraft test data

Description: Craters within the Ganymede Jg-7 quadrangle were divided into seven mappable units. The units represent: (1) irregular or elongate craters, (2) craters with dark ejecta, (3) palimpsests, (4) secondary craters, (5) and craters of young, mature, and old age. Symbols used for crater floors include: (1) flat floors, (2) floors with pits, (3) floora with a central dome or peak, (4) and floors with a central dome and pit. Grooved terrains were divided into five mappable units. Three units of light grooved material represent small, medium, and large grooves, which are arbitrarily divided. The other two units of grooved terrain represent dark grooved materials, and reticulate grooves. Two units of ungrooved dark terrain and two units of ungrooved light terrain were defined. In Galileo Regio, two units were defined repesenting large furrowed grooves, and smaller grooves which are orthogonal to the furrowed grooves.

Description: The relative time of emplacement of some major rock units on Mars was recognized to some degree from geologic mapping using Mariner Images. Correlation charts showing the map units and their position in sequence, however, displayed little discrimination in their vertical range of occurrence. A more detailed time-stratigraphy is currently being developed as Viking geologic mapping of the planet progresses.

Description: Although many radar profiles and images of the area within 20 deg of Mercury's equator had been obtained from 1971 to 1981, at both Goldstone and Arecibo radar facilities, surprisingly little geological analysis had been done with these data until recently. Topographic profiles and radar roughness reflectivity images which can be derived from these data will be crucial in completing the geological mapping of Mercury now underway at the U.S. Geological Survey. Processing of available radar data must be completed to establish any systematic relationship between radar reflectivities and roughness, density, dielectric constant, and other related geological parameters. Specific tasks accomplished for these purposes include the following. Documentation was located and searched to establish the type and quantity of Goldstone 12.5 cm radar observations which were available for Mercury. Data has been collected during approximately 50 observation periods from 1971 to 1981. About half of the data, collected during 1972 and 1973, have been processed, but without adequate documentation. A standardized, well-documented procedure for processing and analysis for all Goldstone Earth-based observations of Mercury was established.

Description: The origin of Mars surface units and the extent of subsequent cratering play key roles in determining surface texture. At scale sizes of 0.1-10 meters, however, there is a growing body of evidence that wind is the dominant force. The direct and indirect evidence which implies that meter-scale surface texture on Mars is controlled by the wind is presented. Since radar is uniquely sensitive to structure on these scales, radio wave scattering data can provide insight on aeolian activity available from no other source.

Description: Two old volcano-tectonic collapse structures are exposed north and northeast of the huge shield volcano, Olympus Mons. They are semicircular and were probably low shield volcanoes similar to Alba Patera, but whose central portions have subsided or collapsed. They form the basement upon which younger volcanic materials of Alba Patera Olympus Mons have been emplaced. The oldest structure, Acheron Fossae is over 700 km across and is north of Olympus Mons. It has a surface of considerable relief broken by graben and extensive en echelon and parallel fractures and faults with varied displacements. Acheron Fossae is the most densely cratered in the Olympus Mons region. The structure must have formed very early in martian time. The second is Halex Fossae, northeast of Olympus Mons. Where exposed, it is cut by a series of arcuate grabens that become closer spaced toward its center. The radii of the fractures indicate that the structure may be at least 250 km across and centered beneath the Olympus Plains. Lava flows appear to have issued from some of the arcuate fractures and to have flowed radially away from the center of Halex Fossae. North of Halex Fossae, material of the same age as Halex Fossae overlaps Acheron Fossae.

Description: High spatial resolution data from the Viking infrared thermal mapper (IRTM) are used to examine the Tharsis volcanoes which are situated within a vast area of low thermal inertia material very fine particle size or very high porosity, with the volcanoes having the lowest thermal inertias. Thermal infrared images of the 1823 flow on Kilauea's southwest rift zone show lower thermal inertias near the vent area where shelly pahoehoe is common while individual channelized aa flows with abundant broken pahoehoe slabs are higher thermal inertia. The increase in aa flows to the southeast leads to a general trend of increasing thermal inertias from near vent to distal areas. Martian shield volcanoes have thermal inertias equal to or higher than their surrounding plans when atmospheric effects are removed from the data. The general increase in thermal inertias away from the summit calderas is consistent with the trend of the Hawaiian 1823 flow and may be related to changing lava properties away from the summit.

Description: A photometrically and geometrically reduced data base is being produced for the Galilean Satellites using Voyager Imaging data. The basic data set used is essentially all the useful satellite images returned by Voyager. Each frame was radiometrically calibrated and many are projected into cartographic formats. Mosaics of low, medium and high resolution frames being made for each satellite consist of registered digital images with intensity values scaled through a traceable calibration procedure to normal albedo values. Many of the mosaics are being made in two versions. One version is an albedo version and the second is a maximum discrimination version in which large variations in brightness across the picture are suppressed.

Description: One unique feature on Mars is the presence of ring furrows which are apparently produced by inversion of topography at the rims of partially buried craters. Ring furrows are flat-floored trenches, circular in plan view, forming rings 7 to 50 km in diameter. The moat is on the order of 0.5 km deep and 2 to 10 km wide, and it surrounds a flat topped circular mesa or plateau that is 5 to 40 km across. The central plateau is at the same elevation or lower than the surrounding plain outside the ring. The circular nature and size range of ring furrows tend to suggest that these features are related to craters partially buried by younger lava flows. The rings have been formed by preferential removal of the exposed crater rims. Ground ice decay, sapping, or fluvial erosion removed the less resistant, porous material of crater rims while leaving the more resistant volcanic flow material. Differential erosion has thus led to a reversal of topography in which the original positive relief of the rim is reduced to a negative relief feature.

Description: The morphology of channels, valleys, chaotic and fretted terrains and many smaller features on Mars is consistent with the hypothesis that localized deterioration of thick layers of ice-rich permafrost was a dominant geologic process on the Martian surface. Such ground ice deterioration gave rise to large-scale mass movement, including sliding, slumping and sediment gravity flowage, perhaps also catastropic floods. In contrast to Earth, such mass movement processes on Mars lack effective competition from erosion by surface runoff. Therefore, Martian features due to mass movement grew to reach immense size without being greatly modified by secondary erosional processes. The Viking Mission to Mars in 1976 provided adequate measurements of the relevant physical parameters to constrain models for Martian permafrost.

Description: High-resolution pictures of talus slopes on Mars show small, dark streaks that characteristically widen downward. These streaks are different from the thin and even streaks of various albedos that stream from cliffs on talus slopes, but gradations between the two streak types occur and not all streaks can be classified with confidence. In order to study the nature and origin of the small, widening, dark streaks, all Viking pictures with a resolution of less than 100 m/pixel were surveyed. To date several hundred streaks were located, but only few are of high enough resolution to be confidently identified as widening downwards. The approximate dimensions of the streaks were measured and their shapes, numbers, position, and spacing on slopes were noted. They were plotted on a topographic map, and their relation to topography, geologic units, and regions of distinct thermal inertia and albedo were studied. Also noted was the season at which images containing streaks were acquired and the direction of illumination. Albedo measurements are in progress. Several streaks can be seen stereoscopically, but none are observed on color images. The observation of small dark streaks on talus slopes on Mars is compatible with an interpretation of their origin as eruptions of small masses of wet debris in places where steep walls intersect aquifers or where seasonal equatorial warming permits the local melting of ground ice.

Description: The valley networks of Mars are widely believed to have formed at a time when climatic conditions on the planet were significantly different from those that currently prevail. This view arises from the following observations: (1) the valleys form integrated branching networks which suggests fluid drainage, and water is the most plausible fluid, (2) the present atmosphere contains only minute amounts of water, (3) the networks appear to be more akin to terrestrial valleys that are eroded by streams of modest discharges than features that form by catastrophic floods, and (4) small streams of water will rapidly freeze under present climatic conditions. Climatic conditions at the time of formation of the valleys are studied based on the assumption that they were cut by running water.

Description: Images of the surface of Venus obtained by the Soviet Venera 9, 10, 13 and 14 landers are analyzed to provide a basis for understanding the nature of geologic processes operating there. Bedrock is exposed at the Venera 10, 13 and 14 sites and is characterized by semi-continuous, flat polygonal to subrounded patches up to several meters in width. The bedrock surface is often dominated by sub horizontal to horizontal layered plates with thicknesses of several cm and abundant linear and polygonal vertical fractures. Soils (particles 1 cm) are abundant at the Venera 9, 10 and 13 sites, but are uncommon at Venera 14. Features indicative of a strong aeolian influence (moats, dunes, wind tails) are not observed. Several hypotheses are considered for the origin of the bedrock surfaces, and it is concluded that bedrock originated from surface lava flows. The relative freshness of features observed by the Veneras suggests that erosion rates are very low or that some bedrock surfaces are geologically young.

Description: A tectonic orgin for Venus banded terrain is consistent with band spacing. Both compressional (folding) and extensional models for band formation can fit present observations. Band spacing cannot distinguish among scenarios for global heat loss and for the origin of highland terrain. Tectonic models for band formation indicate that the surface brittle layer in the venus highlands is no more than a few kilometers thick.

Description: A study to determine the feasibility of conducting experiments to simulate the aeolian environment on Venus as related to wind abrasion was completed. Ideally, such experiments should involve complete investigation of weathering, in which mechanical, thermal, and chemical parameters are taken into account. This is particularly important for Venus, where atmospheric temperatures and pressures at the surface produce an environment which is equivalent to low or medium grade metamorphic conditions on Earth. Details that describe the Venus Aeolian Abrasion Device (VAAD) are included. The VAAD device would enable experiments to be conducted with the same chemistry, temperature, pressure, and other physical properties of the Venus atmosphere near the surface. The proposed device enables the important aeolian parameters to be controlled and monitored, including particle size, velocity, impact-angle and flux, atmospheric pressure, temperature, and gas composition.

Description: Why the lowlands of Mars are concentrated in the Northern Hemisphere and the highlands in the Southern Hemisphere is probably the most fundamental unsolved problem in martian geology. No explanation that accounts both for this asymmetric distribution and for the isostatic equilibrium across the scarp or sloping transition zone dividing the two provinces has been generally accepted; thinning of the lithosphere in the northern hemisphere by internal processes has been suggested. Because other lowland-highland distributions on Mars, Moon, and Mercury are controlled by impact basins, it is proposed that a giant basin formed early in Mars' history has caused the martian hemispheric dichotomy as well.

Description: A number of researchers have concluded that saturation equilibrium cratering exists nowhere in the solar system, and therefore that diameter distributions in even the most heavily cratered provinces reveal initial production functions related to impacting bodies. Based on this premise, different populations of impactors are identified in different epochs and regions of the solar system. These hypotheses are clearly crucial to interpreting planetary history and need further independent examination. The production function in the outer solar system may differ from that in the inner solar system, but it is also possible that viscous relaxation of ice craters or immediate flooding of craters that penetrate through an ice lithosphere into watery substrate may explain the greater deficiency of large craters on icy moons. This problem is controversial and needs more study.

Description: Properties of the planetary surface and subsurface can affect the morphology of impact craters. A mechanism was proposed to explain pedestal craters and domed floors within fresh craters on Ganymede. Voyager 1 and 2 images with resolutions = to or 3.2 km/lp were examined and 523 fresh craters were identified. For each crater, the rim and ejecta diameters were measured, and the crater was characterized by ejecta class(es), interior features, floor morphology and target terrain. Of the craters examined, 97 show moderate to prominent doming of the crater floor; 340 craters have continuous ejecta which terminates in a scarp pedestal craters, of which 86 (25%) have a high albedo diffuse deposit beyond the pedestal.

Description: A systematic survey of the entire Mariner 10 coverage of Mercury was performed to determine the number, distribution and dimensions of additional ancient basins on the planet. Ancient multi-ringed basins on Mercury can be recognized by the following criteria: (1) arcs of massif chains and isolated massifs that protrude through younger units, (2) arcuate segments of lobate ridges (rupes) that align with massifs in circular patterns, (3) arcuate scarps that are aligned with ridges and massif, and (4) isolated regions of anomalously high topography within the intercrater regions of heavily cratered terrain. All of the newly identified basins predate the mercurian intercrater plains, previously held to be the oldest geologic unit on the planet. Subsequent structural evolution of various regions was influenced by the presence of these basins. Smooth plains units appear to be more extensive than mapped by Mariner 10 and more than 90 percent of them appear to be basin contained or basin related. The concentration of extensive smooth plains material within and associated with basin structural and depositional environments suggests a volcanic origin for most of this unit, analogous to the lunar maria. Basins appear to provide the basic structural pattern of early terrestrial planetary crusts.

Description: An improved version of the Pionner-Venus orbital data was used for a statistical analysis of global radar roughness and (alpha(0)) (rho) reflectivity. Classification maps of the venusian surface are produced in a supervised manner on the basis of statistical and empirical studies of the individual data sets. The primary objective is to assess the degree of homogeneity of surface radar properties within topographic provinces in order to map possible geologic boundaries. Maps were produced by correlating two data sets at a time. Classification of specific regions, such as Ishtar, has demonstrated that distinct geological units can be identified.

Description: Interest on Venus has centered on three regions; (1) Aphrodite Terra, especially east of the main uplant portion, (2) Ishtar Terra, especially Lakshmi Planum and its bounding scarp and massifs, and (3) Beta Regio-Phoebe Regio. The last region is topographically similar to the East African rift system, and has been inferred to have a similar tectonic origin. The Aphrodite region is part of a 21,000 km long tectonic zone that seems best explained as due to extension, and that may represent hot spots clustered along an incipient divergent plate boundary. The most interesting and complex portion of this tectonic zone is that part of eastern Aphrodite between Thetis Regio and Atla Regio. In contrast, the Lakshmi Planum region has many topographic characteristics suggesting that it is a true continent, and thus indicative of convergence and a thick crust. Detailed topographic contour maps of eastern Aphrodite Terra and of Lakshmi Planum are included.

Description: The results of analyses of near infrared reflectance spectra are inconsistent with numerous previous interpretations of the Reiner Gamma Formation. These include: (1) nue ardente or volcanic ash deposits, (2) volcanically derived sublimates, (3) high albedo volcanic deposits, and (4) highlands debris emplaced as impact ejecta. These results, strongly suggest that the selective preservation of high albedo features (formed by secondaries) by a local magnetic field enhancement is not a viable hypothesis. The results are generally consistent with, but place constraints on, the cometary impact hypothesis of Schultz and co-workers. While the presence of a magnetized component was not detected in either the bright or dark portions of the Reiner Gamma Formation, this material may be present in amounts under the current detection limits.

Description: On the basis of the icy conglomerate model of cometary nuclei, various observations demonstrate the spotted nature of many or most nuclei, i.e., regions of unusual activity, either high or low. Rotation periods, spin axes and even precession of the axes are determined. The observational evidence for variations in activity over the surfaces of cometary nuclei are listed and discussed. On June 11 the comet IRAS-ARAKI-ALCOCK approached the Earth to a distance of 0.031 AU, the nearest since C/Lexell, 1770 I, providing a unique opportunity for near-nucleus observations. Preliminary analysis of these images establishes the spin axis of the nucleus, with an oblioquity to the orbit plane of approximately 50 deg, and a lag angle of sublimation approximately 35 deg from the solar meridian on the nucleus. Asymmetries of the inner coma suggests a crazy-quilt distribution of ices with differing volatility over the surface of the nucleus. The observations of Comet P/Homes 1892 III, exhibiting two 8-10 magnitude bursts, are carefully analyzed. The grazing encounter produced, besides the first great burst, an active area on the nucleus, which was rotating retrograde with a period of 16.3hr and inclination nearly 180 deg. After the first burst the total magnitude fell less than two magnitudes from November 7 to November 30 (barely naked eye) while the nuclear region remained diffuse or complex, rarely if ever showing a stellar appearance. The fading was much more rapid after the second burst. The grazing encounter distributed a volume of large chunks in the neighborhood of the nucleus, maintaining activity for weeks.

Description: Dione is one of the most geologically complex of the Saturnian satellites. Crater counts and surface morphology indicates the geologic units observed are of variable age and origin. In an attempt to understand the processes which have affected Dione, a geologic map was prepared. Several geologic units were identified; ancient heavily cratered terrain, two plains units: cratered plains and lightly cratered plains, lobate deposits, crater rim deposits and bright wispy materials.

Description: For large parts of the surfaces of the Galilean satellites there is no stereoscopic high resolution imagery, and so for shadow-free regions far from the terminator, the only method of obtaining topograpic information is photoclinometry, the technique of converting brightness variations into local surface tilts and hence into topographic profiles and contour maps. The conversion from brightness changes to slopes require knowledge of the angular photometric function for the type of planetary surface terrain being analyzed, i.e., the relationship describing the brightness of the surface as a function of the angles of incidence (I) and emergence (E) of light at a surface element. In order to investigate the effects of these changes on the shapes of topographic profiles deduced from the functions, an area of grooved terrain (lines 500-505, samples 550-650 on frame 20640.27 0060J2) using wide ranges of values of all the adjustable parameters in Hapke's new photometric function were analyzed.

Description: Exploratory work on the structure of the Ionian lithosphere is reported. The approach is to examine temperature profiles within the lithosphere that result from different distributions of sulfur and silicates and different conductive heat fluxes, then compare such profiles with observations in the expectation that only a limited set of the profiles are possible. In this preliminary work some rather simplistic assumptions were taken and the report should be viewed more as a demonstration of a method rather than a presentation of results.

Description: Final revisions were made in the study of continuum spectrophotometry of 17 comets done at Lick Observatory. Changes based upon this study were introduced into the Divine-Newburn cometary modelling paradigm. Work was begun on modifications to all of the theory based upon the direct nucleus and coma observations made by the Halley space missions.

Description: Spectroscopic and spectrophotometric data on the atmospheres of comets, the outer planets, and Titan at ultraviolet to near-infrared wavelengths were acquired. These data support an effort aimed at characterizing the physical properties and distribution of aerosol particles in the atmospheres of these bodies. New spectrophotometry was acquired of Uranus at 0.2 lambda 0.3 micrometer with IUE; archival IUE spectrophotometry of Uranus and Neptune in this wavelength range was acquired and recalibrated. New estimates of radiometric Bond albedos and global energy budges of Uranus, Neptune and Titan were published.

Description: An Atlas of Comet Halley 1910 II photographs and spectra is being prepared. The major section consists of 838 photographic observations from fifteen observatories around the world. Multiple images of many photographs are reproduced to bring out detail in the near nucleus region, in the coma and in the tail. The Atlas contains a total of 1209 photographic images of the 1910 apparition. In addition there are sections showing drawings from 1935 and 1910. A short section compares 1910 drawings and photographs. The final two sections display digitally processed images from 1910 and 1910 spectra. A three part appendix contains diagrams of various data associated with the 1910 apparition, a set of tables of all 1910 images and a bibliography.

Description: Infrared observations were made of the outer planet satellites. These data provide vital information about the thermophysical properties of satellite surfaces, including internal heat sources for Io. Observations include both broad and narrow band measurements in the 2 to 20 micrometer spectral range. Types of observation and target priority were determined to make maximum use of existing data from Voyager and other missions, on-going and planned missions such as Galileo, were supported and techniques and data for planning new missions and instrumentation were developed.

Description: Improvements to the design of the Mariner spacecraft resulted in the Viking spacecraft. The Viking spacecraft would consist of two major systems - an orbiter and a lander, while the lander would provide the means for safely delivering the scientific instruments to the surface, house, and provide the necessary power source and communication links for those experiments, the orbiter would transport the lander to Mars, rovide a platform for the Viking imaging system so that proposed landing sites could be surveyed and certified, relay lander science information back to Earth, and conduct scientific observations in its own right.

Description: A KC-135A aircraft equipped with wing tip winglets was flight tested to demonstrate and validate the potential performance gain of the winglet concept as predicted from analytical and wind tunnel data. Flight data were obtained at cruise conditions for Mach numbers of 0.70, 0.75, and 0.80 at a nominal altitude of 36,000 ft. and winglet configurations of 15 deg cant/-4 deg incidence, 0 deg cant/-4 deg incidence, and baseline. For the Mach numbers tested the data show that the addition of winglets did not affect the lifting characteristics of the wing. However, both winglet configurations showed a drag reduction over the baseline configuration, with the best winglet configuration being the 15 deg cant/-4 deg incidence configuration. This drag reduction due to winglets also increased with increasing lift coefficient. It was also shown that a small difference exists between the 15 deg cant/-4 deg incidence flight and wind tunnel predicted data. This difference was attributed to the pillowing of the winglet skins in flight which would decrease the winglet performance.

Description: A joint NASA/USAF program was conducted to accomplish the following objectives: (1) evaluate the benefits that could be achieved from the application of winglets to KC-135 aircraft; and (2) determine the ability of wind tunnel tests and analytical analysis to predict winglet characteristics. The program included wind-tunnel development of a test winglet configuration; analytical predictions of the changes to the aircraft resulting from the application of the test winglet; and finally, flight tests of the developed configuration. Pressure distribution, loads, stability and control, buffet, fuel mileage, and flutter data were obtained to fulfill the objectives of the program.

Description: A full-scale winglet flight test on a KC-135 airplane with an upper winglet was conducted. Data were taken at Mach numbers from 0.70 to 0.82 at altitudes from 34,000 feet to 39,000 feet at stabilized flight conditions for wing/winglet configurations of basic wing tip, 15/-4 deg, 15/-2 deg, and 0/-4 deg winglet cant/incidence. An analysis of selected pressure distribution and data showed that with the basic wing tip, the flight and wind tunnel wing pressure distribution data showed good agreement. With winglets installed, the effects on the wing pressure distribution were mainly near the tip. Also, the flight and wind tunnel winglet pressure distributions had some significant differences primarily due to the oilcanning in flight. However, in general, the agreement was good. For the winglet cant and incidence configuration presented, the incidence had the largest effect on the winglet pressure distributions. The incremental flight wing deflection data showed that the semispan wind tunnel model did a reasonable job of simulating the aeroelastic effects at the wing tip. The flight loads data showed good agreement with predictions at the design point and also substantiated the predicted structural penalty (load increase) of the 15 deg cant/-2 deg incidence winglet configuration.

Description: A joint NASA/U.S. industry program to test advanced technology airfoils in the Langley 0.3-meter Transonic Tunnel (TCT) was formulated under the Langley ACEE Project Office. The objectives include providing U.S. industry an opportunity to compare their most advanced airfoils to the latest NASA designs by means of high Reynolds number tests in the same facility. At the same time, industry would again experience in the design and construction of cryogenic test techniques. The status and details of the test program are presented. Typical aerodynamic results obtained, to date, are presented at chord Reynolds number up to 45 x 10(6) and are compared to results from other facilities and theory. Details of a joint agreement between NASA and the Deutsche Forschungs- und Versuchsantalt fur Luft- and Raumfahrt e.V. (DFVLR) for tests of two airfoils are also included. Results of these tests will be made available as soon as practical.

Description: The specific objectives of this experiment are to establish the population and size distribution of meteoroids in the mass range from 10 to the minus 10 power to 10 to the minus 4 power G, to establish the current population of man-made debris in the same mass range, and to obtain data on the physical properties (composition and density) of meteoroids.

Description: The objective of this experiment is to study interplanetary dust, variously referred to as cosmic dust, cometary dust, zodiacial dust, or meteoric dust particles. Specific objectives are to obtain information regarding particle mass and velocity, and to undertake correlative analyses with other experiments, both on LDEF or near the time of the LDEF flight.

Description: The primary objective of this experiment is to investigate the feasibility of future missions of multilayer thin-film detectors acting as energy sorter to collect micrometeoroids, if not in their original shape, at least as fragments suitable for chemical analysis. It is expected that this kind of particle collector will help in solving one of the most puzzling topics in cosmic-dust studies: the mineralogical and chemical composition of the particles. This is a matter of great interest in the study of the origin and evolution of the solar system.

Description: Mass entrainment of round turbulent jet exhausting into cross flow

Description: Sonic jet injection into subsonic free stream

Description: Cross wind effects on trajectory and cross section of turbulent jet

Description: Jet-wake cross section analysis for jet exhausting in free stream flow

Description: Jet lift aerodynamics in cross flowing stream

Description: Test facility and equipment to determine very high Reynolds number effects associated with large boost vehicles

Description: The Tharsis ridge system appears to form a great circle around the major volcanoes. The roughly circumferential orientation of these ridges could be interpreted as the formation of a ridge system in response to a single stress field with a center near Pavonis Mons. Wise, et al. (1979) plotted the perpendiculars to strikes of ridges on the eastern flanks of Tharsis as great circles on the upper hemisphere of an equal area net. In order to further test for circular symmetry and possible other influences on ridge orientations, normals to vector means of ridge orientations were calculated using over 1850 digitized ridge segments sampled in 10 degree boxes. Orientations of individual ridge segments were weighted by their lengths, and the magnitudes of normals to vectors means were weighted by cummulative length of the ridge segments. Normals to vector means with magnitudes less than 100 km are not shown. Assuming a single fold origin for ridges, the resulting plot shows compressive stress trajectories for the ridges in the Tharsis region. The averaged compressive stress orientation around Tharsis confirm the suggestion by Wise, et al. that the ridge system is not concentric to any single point.

Description: In this paper the tectonic features of the Elysium region are identified and characterized. Identification of features was made using USGS controlled photomosaics (Elysium quadrangle, and portions of Amenthes and Cebrenia quadrangles); Viking Orbiter photographic data were used in individual cases to assist in identification. The positions and orientations of tectonic features can then be used, in conjunction with estimates of the mass of the volcanic load obtained from gravity modelling, to constrain the thickness of the elastic lithosphere in the region.

Description: Several 3.8 cm radar frames were calibrated empirically by histogram fitting, because no instrument background data is available. Then data were corrected for geometric distortion by: (1) redetermining position of individual frames using most accurate recent lunar ephemerides; (2) reprojecting frames into simple cylindrical map projection; (3) using most recent catalog of lunar craters to determine the exact positions of features identifiable on radar frames; and (4) correcting for apparent distortion (misplacement of features in frames) by resampling using a different bilinear interpolation derived for each of the parallelopideds of the set defined for each frame. A hardcopy set of corrected frames was produced. Attempts to produce a mosaic of such corrected frames continue. The resulting mosaic can be used to show the systematic relationship between photographic thermal IR and radar data at different wavelengths in a region dominated by both mare and highland terrain.

Description: Studies of the stratigraphy of southwest Coprates have led to further constraints on both the geographic extent and the relative age of the major compressional ridge forming events in the Tharsis region of Mars. Southwestern Coprates is characterized by curvilinear ridges that are regularly spaced, suggestive of harmonic folding. The western edge of the ridged plains unit of Coprates is marked by volcanic flow fronts. In an enhanced Viking-Orbiter image, a ridge can be seen completely surrounded by a flow with only a small portion of the ridge crest still exposed. Comparison of partially buried ridges on the western edge of the ridged plains to those in central Coprates suggests that flooding of the inter-ridge plains does not exceed a few hundred meters. The morphological relationship between the flow units to the west and the ridged plains indicates that the deformational events in this region predates the emplacement of the younger units.

Description: Layered deposits within Valles Marineris and its associated system of canyons have been considered to consist of two different rock types: (1) thick, competent, cliff-forming, light and dark bedded material in canyon walls, and (2) relatively thin, alternating series of light and dark layered material, both horizontal and inclined, that form rounded hills and large flat-topped mesas rising above the canyon floors. The dissimilarity in appearance between canyon wall and floor materials, as well as their contrasting patterns of erosion, have been considered strong evidence that their modes of origin were different.

Description: The scarps along the margins of the Vales Marineris display a complex assemblage of forms that have been related to a variety of mass wasting and sapping processes. These scarp segments display variations in the degree of development of spur and gully topography, the number and density of apparent sapping features and the frequency of large scale landslides which reflect the age, geology and processes of slope development throughout the Valles Marineris. This regional analysis should provide more information on the geologic evolution of the Valles Marineris as well as new insight into the relative importance of different processes in the development of the scarp forms. In order to evaluate the regional variation in scarp form and the influence of time and structure on scarp development geomorphic mapping and morphometric analysis of geologically distinct regions of Valles Marineris is being undertaken.

Description: Parallel studies of Martian geomorphic features and their analogs on Earth continue to be fruitful in deciphering the geologic history of Mars. In the context of rock weathering, the Earth-analog approach is admirably served by the study of meteorites recovered from ice sheets in Antarctica. The weathering environment of Victoria Land possesses several Mars-like attributes. Four of the five Antarctic meteorites being studied contain rust and EETA79005 further possesses a conspicuous, dark, weathering rind on one side. Secondary minerals (rust and salts) occur both on the surfaces and interiors of some of the samples and textural evidence indicates that such secondary mineralization contributed to physical weathering (by salt riving) of the rocks. Several different rust morphologies occur and emphasis is being placed on identifying the phase compositions of the various rust occurrances. A thorough understanding of terrestrial weathering features of the meteorites is a prerequisite for identifying possible Martian weathering features (if such features exist) that might be postulated to occur in some meteorites.

Description: Photometric studies of crater related bright and dark streaks have strongly supported the hypothesis that the bright streaks are excess dust deposits and dark streaks are erosional windows in a partial dust cover. Red-blue (and red-violet) plots show that bright streaks are consistent with mosaics of bright red dust and background material. Here the plains are also consistent with a partial dust cover; the dark streak is the least covered area. Bright and dark streaks both reverse contrast relative to surrounding plains at phase angles over 100 deg in violet filter images. The similar phase behavior of both bright and dark streaks supports the idea that they are both changes in the amount of dust cover. Red-violet plots of bright streaks are most easily explained by mosaics of optically thick dust and plains material. Lengths of bright streaks are independent of their contrasts. This suggests the streak deposition, if in the mosaic patterns indicated above, is a function of available sites of deposition, rather than atmospheric dust loading. Contrasts of dark streaks with plains indicate the plains have fractional dust covers nealy as great as the maximum additional cover in bright streaks. The bright streaks thus store little of the global supply of dust.

Description: Viking Lander 1 observations on Mars were punctuated by a strong local dust storm after two martian years of mild wind conditions. Tens of micrometers of dust settled to the surface during global dust storms of the first two falls and winters; some of this dust was locally removed during the second year. A late winter local dust storm of the first year caused little or no erosion of the surface materials despite wind speeds of 25 to 30 m/s. The strong local dust storm occurred during late winter of the third martian year. Winds of this storm altered and demolished small conical piles of surface materials constructed at the onset the first winter, removed 4 to 5 mm size fragments, displaced centimeter size fragments, destroyed clouds in areas disrupted by the sampler and footpad, eroded impact pits, and darkened the sky. Movement of erosional products and tiny wind tails indicate easterly to northeasterly winds. If the 4 to 5 mm size fragments were entrained and removd by the wind, threshold friction speeds near 3 to 5 m/s would have been required for the atmospheric temperatures and pressures that prevailed during the late winter of the third year.

Description: There are classes of landforms whose presence on Mars is strongly suggestive, if not confirmatory, of the participation of volatiles, presumably water, in its geomorphic development: (1) valley networks, (2) outflow channels, (3) landslides, and (4) flow-ejecta blankets. The first two may represent landforms generated by the movement of volatiles from sources, while the latter two probably represent the dissipation of energy generated by forcing inputs (e.g., kinetic energy and gravity) modulated by volatiles. In many areas on Mars, all four processes have acted on the same lithologic materials and were influenced by the composition of those units, and possibility by the climatic regime at the time of their formation. One of the approaches discussed to this specific problem of landform genesis, and to the general problem of the present and past states of martian volatiles, is to attempt to constrain the distribution, amount, and history of available volatiles by using possible evidence of volatile participation expressed in the morphology of other related landforms (e.g., flow-ejecta blankets and landslides) coupled with physical models for landform genesis.

Description: Most cratering experiments are designed to study the effects of a single hypervelocity impact into a target of uniform properties. Experiments involving multiple impacts are usually limited to low velocity projectiles and unconsolidated target materials. Gault described saturation cratering in an unconsolidated target. Quaide and Oberbeck studied crater forms produced by hypervelocity impact into layered targets. Several investigators have modeled the generation of either a regolith or megaregolith by repeated impact on planetary surfaces. Studies now in progress examine changes in crater morphology and target properties by repeated impact into an initially consolidated target. Current studies employ low velocity projectiles (2 g at 0.5 km/sec) and consolidated salt targets. Records of crater size, morphology, and accumulated ejecta thickness are maintained as impacts collect on the surface.

Description: The crater size/frequency distributions of large ( 8 km) craters on the Moon and terrestrial planets display two very different curves representing two crater populations. The heavily cratered regions of the Moon, Mercury, and Mars show the same highly structured curve which cannot be represented by a single slope distribution function. In contrast, the lunar post mare crater population has a size/frequency distribution which differs significantly from that in the highlands over the same diameter range, and can be represented by a single-slope distribution function of -2.8 differential. On areas of martian lightly cratered northern plains, the crater population is essentially identical to that of the post mare population. This indicates that the same two families of impacting objects were responsible for the cratering records on both Moon and Mars. The thickness of mantling material varies among the various plains units, and can be calculated from the depth/diameter scaling relations for martian craters.