ALBERT

Description: This report is part of a series of reports that address flight deck design and evaluation, written as a response to loss of control accidents. In particular, this activity is directed at failures in airplane state awareness in which the pilot loses awareness of the airplane's energy state or attitude and enters an upset condition. In a report by the Commercial Aviation Safety Team, an analysis of accidents and incidents related to loss of airplane state awareness determined that hazard alerting was not effective in producing the appropriate pilot response to a hazard (CAST, 2014). In the current report, we take a detailed look at 28 airplane state awareness accidents and incidents to determine how well the hazard alerting worked. We describe a five-step integrated alerting-to-recovery sequence that prescribes how hazard alerting should lead to effective flight crew actions for managing the hazard. Then, for each hazard in each of the 28 events, we determine if that sequence failed and, if so, how it failed. The results show that there was an alerting failure in every one of the 28 safety events, and that the most frequent failure (20/28) was tied to the flight crew not orienting to (not being aware of) the hazard. The discussion section summarizes findings and identifies alerting issues that are being addressed and issues that are not currently being addressed. We identify a few recent upgrades that have addressed certain alerting failures. Two of these upgrades address alerting design, but one response to the safety events is to upgrade training for approach to stall and stall recovery. We also describe issues that are not being addressed adequately: better alert integration for flight path management types of hazards, airplanes in the fleet that do not meet the current alerting regulations, a lack of innovation for addressing cases of channelized attention, and existing vulnerabilities in managing data validity.

Description: Air traffic in the United States has continued to grow at a steady pace since 1980, except for a dip immediately after the tragic events of September 11, 2001. There are different growth scenarios associated both with the magnitude and the composition of the future air traffic. The Terminal Area Forecast (TAF), prepared every year by the FAA, projects the growth of traffic in the United States. Both Boeing and Airbus publish market outlooks for air travel annually. Although predicting the future growth of traffic is difficult, there are two significant trends: heavily congested major airports continue to see an increase in traffic, and the emergence of regional jets and other smaller aircraft with fewer passengers operating directly between non-major airports. The interaction between air traffic demand and the ability of the system to provide the necessary airport and airspace resources can be modeled as a network. The size of the resulting network varies depending on the choice of its nodes. It would be useful to understand the properties of this network to guide future design and development. Many questions, such as the growth of delay with increasing traffic demand and impact of the en route weather on future air traffic, require a systematic understanding of the properties of the air traffic network. There has been a major advance in the understanding of the behavior of networks with a large number of components. Several theories have been advanced about the evolution of large biological and engineering networks by authors in diversified disciplines like physics, mathematics, biology and computer science. Several networks exhibit a scale-free property in the sense that the probabilistic distribution of their nodes as a function of connections decreases slower than an exponential. These networks are characterized by the fact that a small number of components have a disproportionate influence on the performance of the network. Scale-free networks are tolerant to random failure of components, but are vulnerable to selective attack on components. This paper examines two network representations for the baseline air traffic system. A network defined with the 40 major airports as nodes and with standard flight routes as links has a characteristic scale: all nodes have 60 or more links and no node has more than 460 links. Another network is defined with baseline aircraft routing structure exhibits an exponentially truncated scale-free behavior. Its degree ranges from 2 connections to 2900 connections, and 225 nodes have more than 250 connections. Furthermore, those high-degree nodes are homogeneously distributed in the airspace. A consequence of this scale-free behavior is that the random loss of a single node has little impact, but the loss of multiple high-degree nodes (such as occurs during major storms in busy airspace) can adversely impact the system. Two future scenarios of air traffic growth are used to predict the growth of air traffic in the United States. It is shown that a three-times growth in the overall traffic may result in a ten-times impact on the density of traffic in certain parts of the United States.

Description: This presentation will: Describe some of the exploratory work and products of the UCAT, which lay the groundwork for NASAs UAM investments; Describe the UAM Grand Challenge

Description: This article discusses the use of numerical optimization procedures to aid in the calibration of turbulence model coefficients. Such methods would increase the rigor and repeatability of the calibration procedure by requiring clearly defined and objective optimization metrics, and could be used to identify unique combinations of coefficient values for specific flow problems. The approach is applied to the re-calibration of an explicit algebraic Reynolds stress model for the incompressible planar mixing layer using the Nelder-Mead simplex algorithm and a micro-genetic algorithm with minimally imposed constraints. Three composite fitness functions, each based upon the error in the mixing layer growth rate and the normal and shear components of the Reynolds stresses, are investigated. The results demonstrate a significant improvement in the target objectives through the adjustment of three pressure-strain coefficients. Adjustments of additional coefficients provide little further benefit. Issues regarding the effectiveness of the fitness functions and the efficiency of the optimization algorithms are also discussed.

Description: This manual describes the installation and execution of FUN3D (Fully-UNstructured three-dimensional CFD (Computational Fluid Dynamics) code) version 13.5, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver enables efficient gradient-based design and grid adaptation to reduce estimated discretization error. FUN3D is available with and without a reacting, real-gas capability. This generic gas option is available only for those persons that qualify for its beta release status.

Description: A computational fluid dynamics code has been developed for large-eddy simulations (LES) of turbulent flow. The code uses high-order of accuracy and high-resolution numerical methods to minimize solution error and maximize the resolution of the turbulent structures. Spatial discretization is performed using explicit central differencing. The central differencing schemes in the code include 2nd- to 12th-order standard central difference methods as well as 7-, 9-, 11- and 13-point dispersion relation preserving schemes. Solution filtering and high-order shock capturing are included for stability. Time discretization is performed using multistage Runge-Kutta methods that are up to 4th order accurate. Several options are available to model turbulence including: Baldwin-Lomax and Spalart-Allmaras Reynolds-averaged Navier-Stokes turbulence models, and Smagorinsky, Dynamic Smagorinsky and Vreman sub-grid scale models for LES. This report presents the theory behind the numerical and physical models used in the code and provides a user's manual to the operation of the code.

Description: FACT is a software program that provides important information about winter weather operations to airline dispatchers and airport personnel. FACT has a "quad" design and shows various maps, text, and tabular information. It also has a team messaging capability. It is meant to be used by airline dispatchers and airport personnel to manage winter storms. This presentation is for a meeting with Boeing. COMMERCIAL AIRCRAFT; AIRLINE OPERATIONS; STORMS COMPUTER PROGRAMS; AIRLINE OPERATIONS; WEATHER FORECASTING; MESSAGE PROCESSING; AIRCRAFT COMMUNICATION; WINTER; STORMS (METEOROLOGY); COMMERCIAL AIRCRAFT

Description: No abstract available

Description: The Predictive Thermal Control (PTC) technology development project is a multiyear effort initiated in Fiscal Year (FY) 2017, to mature the Technology Readiness Level (TRL) of critical technologies required to enable ultra-thermally-stable telescopes for exoplanet science. A key PTC partner is Harris Corporation (Rochester NY).

Description: Experiments are being conducted in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility to quantify the effects on turbulent convective heat transfer of surface roughness representative of a new class of 3D woven thermal protection system mRough-wall turbulent heat transfer measurements were obtained on ballistic-range models in hypersonic flight in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility. Each model had three different surface textures on segments of the conic frustum: smooth wall, sand roughness, and a pattern roughness, thus providing smooth-wall and sand-roughness reference data for each test. The pattern roughness was representative of a woven thermal protection system material developed by NASA's Heatshield for Extreme Entry Environment Technology project. The tests were conducted at launch speeds of 3.2 km/s in air at 0.15 atm. Roughness Reynolds numbers, k+, ranged for 12 to 70 for the sand roughness, and as high as 200 for the pattern roughness. Boundary-layer parameters required for calculating k+ were evaluated using computational fluid dynamics simulations. The effects of pattern roughness are generally characterized by an equivalent sand roughness determined with a correlation developed from experimental data obtained on specifically-designed roughness patterns that do not necessarily resemble real TPS materials. Two sand roughness correlations were examined: Dirling and van Rij, et al. Both gave good agreement with the measured heat-flux augmentation for the two larger pattern roughness heights tested, but not for the smallest height tested. It has yet to be determined whether this difference is due to limitations in the experimental approach, or due to limits in the correlations used. Future experiments are planned that will include roughness patterns more like those used in developing the equivalent sand roughness correlations.aterials being developed by NASA's Heatshield for Extreme Entry Environment Technology (HEEET) project. Data were simultaneously obtained on sand-grain roughened surfaces and smooth surfaces, which can be compared with previously obtained data. Results are presented in this extended abstract for one roughness pattern. The full paper will include results from three roughness patterns representing virgin HEEET, nominal turbulent ablated HEEET, and twice the roughness of nominal turbulent ablated HEEET. Results will be used to compare with commonly used equivalent sand grain roughness correlations.

Description: This work introduces an approach to estimate the complexity of a low-altitude air traffic scenario involving multiple UASs using mathematical programming. Given a set of multi-point UAS flight trajectories, vehicle dynamics, and a conflict resolution algorithm, an abstract model is developed such that it can be solved quickly using a mathematical programming optimization software without running high-fidelity simulations that can be computationally expensive and may not suit real-time apA quick and accurate assessment of complexity for a given traffic scenario can help plan and schedule flights to alleviate traffic bottleneck and mitigate operation risks, especially for unmanned aerial system traffic management where high traffic density or complexity is expected. This work introduces a traffic scenario complexity metric that was constructed based on the number of potential conflicts weighted by the conflict resolution cost associated. The cost associated with a conflict is calculated based on the corresponding conflict resolution maneuvers. To obtain the conflict resolution maneuvers, a MILP-based optimization was formulated with the vehicle model and conflict management parameters incorporated. To evaluate the complexity metrics, an approach of using measurements from high-fidelity simulations was proposed. The scenario complexity measurements for 920 random-generated scenarios were obtained through high-fidelity simulations and treated as the ground truth. Two statistics methods: Pearson and Alternative Conditional Expectations were applied for analysis. The results showed that the number of flights has low correlation with the scenario complexity according to the correlation coefficients calculated by both methods. The Alternative Conditional Expectations method shows that the proposed scenario complexity metric has better correlation with the ground truth than the number of potential conflicts.plications. In the abstract model, each vehicle is represented by a time-varied vector associated with position, speed, and heading information. The total extra distance that aircraft need to divert from their original routes to avoid collisions is computed and used to setup a quadratic programming formula. The metrics including the number of conflicts and extra distances travelled by all vehicles are then utilized to estimate the complexity of a given UAS flight scenario. Results and verification against high-fidelity simulations will be provided in the final draft.

Description: Target generation systems provide the positions of aircraft in air traffic simulations. As the scope of the simulation domains expand, there is a need to develop systems that can provide position reports for thousands of aircraft simultaneously and at update rates that support out-the-window visualization. This paper discusses the motivation and reasoning behind investigating development of a next generation target generator through distributed computing using clustered node processing and how a target generation system benefit future research that utilizes human-in-the-loop simulations.

Description: This paper presents an encounter-based simulation architecture developed at NASA to facilitate flexible and efficient Detect and Avoid modeling in parametric or tradespace studies on large data sets. The basic premise of this tool is that large-scale input data can be reduced to a set of `canonical encounters' and that using the reduced data in simulations does not lead to loss of fidelity. A canonical encounter is specified as ownship and intruder flight portions potentially resulting in a loss of well clear along with a set of properties that characterize the encounter. The advantages of using canonical encounters include faster simulations, reduced memory footprint, ability to select encounters based on user-specified criteria, shared encounters across multiple teams, peer-reviewed encounters, and a better understanding of the input data set, to name a few.

Description: Current radar-based air traffic service providers may preserve privacy for military and corporate operations by procedurally preventing public release of selected flight plans, position, and state data. The FAA mandate for national adoption of Automatic Dependent Surveillance Broadcast (ADS-B) in 2020 does not include provisions for maintaining these same aircraft-privacy options, nor does it address the potential for spoofing, denial of service, and other well-documented risk factors. This paper presents an engineering prototype that embodies a design and method that may be applied to mitigate these ADS-B security issues. The design innovation is the use of an open source permissioned blockchain framework to enable aircraft privacy and anonymity while providing a secure and efficient method for communication with Air Traffic Services, Operations Support, or other authorized entities. This framework features certificate authority, smart contract support, and higher-bandwidth communication channels for private information that may be used for secure communication between any specific aircraft and any particular authorized member, sharing data in accordance with the terms specified in the form of smart contracts. The prototype demonstrates how this method can be economically and rapidly deployed in a scalable modular environment.

Description: Over the last 5 years, the Heatshield for Extreme Entry Environment Technology (HEEET) project has been working to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations such as Venus and Saturn. A key aspect of the project has been the development of the manufacturing and integration processes/procedures necessary to build a heat shield utilizing the HEEET 3D-woven material. This has culminated in the building of a 1-meter diameter Engineering Test Unit (ETU) representative of what would be used for a Saturn probe. The present talk provides an overview of recent testing of NASA's Heatshield for Extreme Entry Environment Technology (HEEET) 3D Woven TPS. Under the current program, the ETU has been subjected to Thermal and Mechanical loads typical of deep space mission to Saturn. Thermal testing of HEEET coupons has performance up to 4,500 watts per centimeter squared at 5 atmospheres stagnation pressure and successful shear performance up to 3000 pascals at 1,650 watts per centimeter squared at 2.6 atmospheres pressure.

Description: The paper presents an efficient trajectory generation and tracking approach for multi-rotor air vehicles operating in urban environment, which takes into account uncertainties in the urban wind field and in the vehicle's parameters. Generated trajectories are sufficiently smooth, based on the differential flatness of the vehicle's dynamics and optimal in the sense of minimum agility and time. They pass through given set of way points, guarantee flight without a side-slip, and satisfy vehicle's dynamics and actuator constraints. In addition, an algorithm is presented to compute the required power to traverse the generated trajectory. Presented algorithms are implementable in real time using on-board computers. They do not take into account the vehicle's existing flight controller, hence there is no guarantee that the controller will be able to provide acceptable tracking of the generated trajectory, especially in the presence of atmospheric disturbances. To this end, we propose an adaptive augmentation algorithm to improve vehicle's performance by taking into account the effects of disturbances and on-line estimates of vehicle's existing flight controller's gains. The algorithms have been verified by simulations using DJI S1000 octocopter's model.

Description: Laser Rayleigh scattering was used to investigate clusters in the free-stream flow at Arnold Engineering Development Centers Tunnel 9 (T9). The facility was run at Mach-14, with a pure-N2 flow medium, and at several total pressures and temperatures. Using an excimer laser operating at 248 nm, the Rayleigh instrument imaged scattering from the focused laser beam in the free-stream. As a wind-tunnel flow is accelerated, it cools and approaches the condensation boundary. As a precursor to condensation, small clusters of molecules are first formed, but the individual clusters are too small to be spatially resolved in typical images of the beam. Thus clusters effectively add a spatially smooth background signal to the pure diatomic-molecule Rayleigh signal. The main result of the present work is that clustering was not significant. After correcting for interference by small particles imbedded in the T9 flow, cluster scattering was unobservable or smaller than one standard deviation (1-sigma) of the uncertainties for almost all tunnel runs. The total light scattering level was measured to be 1.05 +/- 0.15 (1-sigma) of the expected diatomic scattering, when averaged over the entire usable data set. This result included flow conditions that were supercooled to temperatures of ~ 20 K, about 25 K below the condensation limit of ~ 45 K. Thus the Mach-14 nozzle flow is essentially cluster-free for many supercooled conditions that might be used to extend the facility operating range to larger Reynolds numbers.

Description: NASA's UTM project is conducting research on a traffic management concept for small unmanned aircraft systems (UAS) flying in low altitude, uncontrolled airspace. The project started in 2015 and is developing prototype UTM systems of successively complex technical capability levels (TCL) that are tested in the field. To date TCL levels 1-3 have been tested and TCL 4 will be tested in the summer of 2019. Project results are transferred to the FAA and industry to advance the adoption, implementation, and design standards of future UTM systems.

Description: Mission, landing and recovery operations for the Orion crew module involve reentry into the Earth's atmosphere and the deployment of three Nomex parachutes to slow the descent before landing along the west coast of the United States. Orion may have residual fuel (hydrazine, N2H4) or coolant (ammonia, NH3) on board which are both highly toxic to crew in the event of exposure. These risks were evaluated using a first principles analysis approach through fluid dynamics modeling. Plume calculations were first performed with the ANSYS Fluent computational fluid dynamics code. Data were then extracted at locations relevant to crew safety such as the snorkel fan inlet and the egress hatch. Mixing calculations were performed to quantify exposure concentrations within the crew bay before and during egress and departure. Finally, results included herein were used to inform the Orion post-landing Concept of Operations (ConOps) so that strategies could be formulated to maintain crew safety in the event of the loss of fuel or coolant.

Description: During instrument-level or spacecraft-level ground testing, heat pipes may be placed in reflux mode, with condenser above evaporator. A liquid pool will form at the bottom of the heat pipe. If heat is applied to a site below the surface of the liquid pool in a vertical heat pipe, the heat pipe can work properly under reflux mode. A superheat is required for startup. If heat is applied to a site above the liquid pool, the heat pipe is not expected to work unless additional heat is applied to the liquid pool to provide the needed flow circulation. There are many reason to minimize the additional heater power. An experimental investigation was conducted to study the heat pipe behavior under this configuration.

Description: In this report we have catalogued the flow regimes observed in microgravity, summarized correlations for the pressure drop and rate of heat transfer that are commonly used, and discuss the validation of a few correlations from available experimental results. Two-phase flow through some specific components such as bends, tees, filters and pumps are discussed from a physical perspective to guide the designer on how reduced gravity might affect their performance. Phase separation in zero gravity is addressed through the behavior and basic design concepts for devices based on passive centrifugal action, capillary forces, gas extraction through a membrane installed in a channel wall and the use of a syringe with a perforated piston to remove bubbles from small liquid volumes. We address the common instabilities that develop in flow loops owing exclusively to the two-phase nature of the flow, e.g., Ledinegg instability and concentration waves. Finally we briefly review flow metering and gauging; two-phase flow through porous media, where pressure drop and flow regime map correlations in zero-g are a current research topic; and basic operation principles of heat pipes and capillary pumped loops.

Description: This joint briefing presents open and closed loop metrics about the performance of a reference Detect-and-Avoid algorithm using encounters built from NASA's UAS mission trajectories and Lincoln Lab's uncorrelated encounter model.

Description: This work introduces an approach to estimate the complexity of a low-altitude air traffic scenario involving multiple UASs using mathematical programming. Given a set of multi-point UAS flight trajectories, vehicle dynamics, and a conflict resolution algorithm, an abstract model is developed such that it can be solved quickly using a mathematical programming optimization software without running high-fidelity simulations that can be computationally expensive and may not suit real-time applications. In the abstract model, each vehicle is represented by a time-varied vector associated with position, speed, and heading information. The total extra distance that aircraft need to divert from their original routes to avoid collisions is computed and used to setup a quadratic programming formula. The metrics including the number of conflicts and extra distances travelled by all vehicles are then utilized to estimate the complexity of a given UAS flight scenario. Results and verification against high-fidelity simulations will be provided in the final draft.

Description: 5/22/2019 National Aeronautics and Space Administration 1 Airspace Technology Demonstration 2 (ATD-2) Analysis of APREQ Flights at CLT May 22, 2019 5/22/2019 Objective 2 Quantify impact of IADS Phase 1 & 2 capabilities on APREQ flights at CLT with respect to: Compliance to the Controlled Take Off Time (CTOT) Benefits for APREQ flights that use IDAC to renegotiate for an earlier CTOT Benefits of pre-scheduling APREQ flights using the Earliest Off Block Time (EOBT) Relationship between EOBT compliance and rescheduling CTOT 5/22/2019 CLT APREQ Daily Compliance(Compliance Improvement Since ATD-2 Start) 3 Steady increase of APREQ compliance over the life of the project. Reduced variation in compliance leading to improved predictability. In addition to overall improved compliance into TBM systems, the predictability is increasing 5/22/2019 APREQ Compliance 10K Rolling Window 4 The most substantial APREQ compliance improvements started with Phase 2 capability (AEFS integration, ZTL IDAC, pre-scheduling and scheduler updates). 5/22/2019 IADS Phase 1 & 2 Benefit Mechanisms 5 1. Collaborative surface metering Reduced engine run time Reduced fuel consumption and emissions 2. Overhead stream operational integration a.Scheduling controlled flights at the gate Reduced engine run time Reduced fuel consumption and emissions b.APREQ renegotiating for an earlier slot Reduced total delay Passenger value of time and crew costs Reduced engine run time Reduced fuel consumption and emissions Benefits (1) and (2a) achieved through tactical gate holds Benefit (2b) achieved through APREQ renegotiation process described below Step 1: APREQ flight has a release time but is capable of taking off earlier Step 2: FAA TMC uses the IDAC green space / red space to identify and request an earlierslot in the overhead stream Step 3: Aircraft receives earlierrelease time and the difference between the release times is the reduction in delay 5/22/2019 Benefits for APREQ flights using IDAC to renegotiate for earlierCTOT 6 LBS Fuel 270.7 hours of delay saved by electronically renegotiating a better overhead stream time for 2,071 flights. The benefits described here are associated with better use of existing capacity in the overhead stream, and technology to reduce surface delay. These benefits are in addition to (distinct from) surface metering savings. 5/22/2019 APREQ Delay For Pre-Scheduled Flights into KATL Have Been Reduced and are More Predictable For the Last Five Months 7 Substantial Improvements in predictability of delay for the last 5 months 5/22/2019 EOBT Compliance / CTOT Reschedulefor Pre-Scheduled Flights into KATL 8 5/22/2019 Wrap-up 9 Compliance to the CTOT has improved throughout the lifecycle of ATD-2 with biggest improvements following the introduction of Phase 2 capabilities Rescheduling APREQ flights using IDAC has reduced 270.7 hours of delay at CLT Predictability of local surface delay for APREQ flights is substantially improved via pre-scheduling with the IADS system Pre-scheduled flights that reschedule for later times tend to call ready later with respect to EOBT

Description: Current turbulence models, such as those employed in Reynolds-averaged Navier-Stokes CFD, are unable to reliably predict the onset and extent of the three-dimensional separated flow that typically occurs in wing-fuselage junctions. To critically assess, as well as to improve upon, existing turbulence models, experimental validation-quality flow-field data in the junction region is needed. In this report, we present an overview of experimental measurements on a wing-fuselage junction model that addresses this need. The experimental measurements were performed in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The model was a full-span wing-fuselage body that was configured with truncated DLR-F6 wings, both with and without leading-edge extensions at the wing root. The model was tested at a fixed chord Reynolds number of 2.4 million, and angles-of-attack ranging from -10 degrees to +10 degrees were considered. Flow-field measurements were performed with a pair of miniature laser Doppler velocimetry (LDV) probes that were housed inside the model and attached to three-axis traverse systems. One LDV probe was used to measure the separated flow field in the trailing-edge junction region. The other LDV probe was alternately used to measure the flow field in the leading-edge region of the wing and to measure the incoming fuselage boundary layer well upstream of the leading edge. Both LDV probes provided measurements from which all three mean velocity components, all six independent components of the Reynolds-stress tensor, and all ten independent components of the velocity triple products were calculated. In addition to the flow-field measurements, static and dynamic pressures were measured at selected locations on the wings and fuselage of the model, infrared imaging was used to characterize boundary-layer transition, oil-flow visualization was used to visualize the separated flow in the leading- and trailing-edge regions of the wing, and unsteady shear stress was measured at limited locations using capacitive shear-stress sensors. Sample results from the measurement techniques employed during the test are presented and discussed.

Description: A two-step automated Multi-Aircraft Control System traffic scenario generation process for Human-in-the-Loop evaluations of air traffic management concepts is described. The first step of the two-step process employs the scenario generation capability currently available in NASA's Air Traffic Management Testbed. The second step refines the scenario by filtering flights from the traffic scenario based on route length, cruise speed, cruise altitude, entry time and the desired ratio of internal to external flights. A solution for achieving the desired ratio of internal to external flights, where internal flights are shorter flights and external flights are longer flights based on a distance threshold, is described. Finally, schedulers are described for shaping the hourly arrival traffic count as a function of time in response to airport capacity constraint or for increasing the traffic demand with respect to the available arrival capacity. Results generated for arrival traffic to the four major airports in the New York Metroplex on a busy day using the two-step procedure are discussed. These results show that traffic scenarios for Multi-Aircraft Control System that meet the Human-in-the-Loop and fast-time simulation requirements can be created automatically following the procedures described in the paper. The automated process will improve the accuracy and efficiency by eliminating the tedious manual process for scenario generation.

Description: Human behavior often consists of a series of distinct activities, each characterized by a unique signature of visual behavior. This is true even in a restricted domain, such as piloting an aircraft, where patterns of visual signatures might represent activities like communicating, navigating, and monitoring. We propose a novel analysis method for gaze-tracking data, to perform blind discovery of these activities based on their behavioral signatures. The method is in some respects similar to recurrence analysis, but here we compare not individual fixations, but groups of fixations aggregated over a fixed time interval. The duration of this interval is a parameter that we will refer to as . We assume that the environment has been divided into a set of N different areas-of-interest (AOIs). For a given interval of time of duration , we compute the proportion of time spent fixating each AOI, resulting in an N-dimensional vector. These proportions can be converted to counts by multiplying by divided by the average fixation duration (another parameter that we fix at 280 milliseconds). We compare different intervals by computing the chi-square statistic. The p-value associated with the statistic is the likelihood of observing the data under the hypothesis that the data in the two intervals were generated by a single process with a single set of probabilities governing the fixation of each AOI. We have investigated the method using a set of 10 synthetic "activities," that sample 4 AOIs. Four of these activities visit 3 of the 4 AOIs, with equal probability; as there are four different ways to leave-one- out, there are four such activities. Similarly, there are six different activities that leave-two-out. Sequences of simulated behavior were generated by running each activity for 40 seconds, in sequence, for a total of 6.7 minutes. The figure to the right shows the matrix of chi-square statistics, using a value of 2.8 seconds for , corresponding to 10 fixations. Low values (dark) indicate poor evidence for activity differences, while high values (bright) indicate strong evidence. The dark squares along the main diagonal each correspond to the forty second intervals in which the activity was held constant; the 4x4 block at the lower left corresponds to the four leave-one-out activities, while the 6x6 block in the upper right corresponds to the leave-two-out activities. (The anti-diagonal pattern of white squares indicates those activity pairs that share no AOIs.) The chi-square values can be binarized by choosing a particular significance level; we are interested in grouping bins that represent the same activity, effectively accepting the null hypothesis. Therefore, we may adopt a relatively lax criterion; for example, choosing a p-value of 0.2 means that two behaviors that have only a 1-in-5 chance of being produced by a single activity might nevertheless be clustered together. We have explored several methods to perform clustering on the data and solving for the activity probabilities. Greedy methods begin by selecting the time bin that is similar to the most (or least) other bins, and then forming a cluster from it and all other non-discriminable bins. These methods show mediocre performance, as they do not take into account temporal contiguity. Preliminary results indicate that methods that "grow" clusters in time from seed points perform better.

Description: The InSight Mars Lander successfully landed on the surface on November 26, 2018. This poster will describe the methodologies and margins used in developing the aerothermal environments for design of the thermal protection systems (TPS), as well as a prediction of as-flown environments based on the best estimated trajectory. The InSight mission spacecraft design approach included the effects of radiant heat flux to the aft body from the wake for the first time on a US Mars Mission, due to overwhelming evidence in ground testing for the European ExoMars mission (2009/2010) [1] and 2010 tests in the Electric Arc Shock Tube (EAST) facility [2]. The radiant energy on an aftbody was also recently confirmed via measurement on the Schiaparelli mission [3]. In addition, the InSight mission expected to enter the Mars atmosphere during the dust storm season, so the heatshield TPS was designed to accommodate the extra recession due to the potential dust impact. This poster will compare the predicted aerothermal environments using the reconstructed best estimated trajectory to the design environments. Design Approach: The InSight spacecraft was planned to be a near-design-to-print copy of the Phoenix spacecraft. The determination of the heatshield TPS requirements was approached as if it was a new design due to the new requirement of flying through a dust storm. The baseline for aftbody was build-to-print, and all analyses focused on ensuring adequate margin. This proved to be a challenge because the Phoenix aftbody was designed to withstand only convective heating and the InSight aftbody was evaluated for both convective and radiative heating. Aerothermal environments were predicted using the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) and the Data Parallel Line Relaxation (DPLR) CFD codes, and the Nonequilibrium Radiative Transport and Spectra Program (NEQAIR) utilizing bounding design trajectories derived from Monte Carlo analyses from the Program to Optimize Simulated Trajectories II (POST2). In all cases, super-catalytic flowfields were assigned to ensure the most conservative heating results. Two trajectories were evaluated: 1) the trajectory with the maximum heat flux was utilized to determine the flowfield characteristics and the viability of the selection of TPS materials; and 2) the trajectory with the maximum heat load was used to determine the required thicknesses of the TPS materials. Evaluation of the MEDLI data [4], along with ground test data [5] led to the determination of whether or not the flow would transition from laminar to turbulent on the heatshield, which also determined the TPS sizing location for the heatshield. Aerothermal margins were added for the convective heating and developed for the radiative heating. TPS material sizing was determined with the Reaction Kinetic Ablation Program (REKAP) and the Fully Implicit Ablation and Thermal Analysis program (FIAT) using a three-branched approach to account for aerothermal, material response, and material properties uncertainties. In addition, the heatshield recession was augmented by an analysis of the effect of entry through a potential dusty atmosphere using a methodology developed in References [6] and [7]. These analyses resulted in an increase to the Phoenix heatshield TPS thickness. Reconstruction Efforts: Once the best estimated trajectory is reconstructed by the team, the LAURA/HARA (High-Temperature Aerothermo-dynamic Radiation model) and DPLR/NEQAIR code pairs will be used to predict the as-flown aerothermal conditions. In these runs, fully-catalytic flowfields will be assigned because it is a more physically accurate description of the chemistry in the flow. Once again, determination of the onset of turbulence on the heatshield will be evaluated. The as-flown aerothermal environments will then be compared to the design environments.

Description: A two-step automated Multi-Aircraft Control System traffic scenario generation process for Human-in-the-Loop evaluations of air traffic management concepts is described. The first step of the two-step process employs the scenario generation capability currently available in NASA's Air Traffic Management Testbed. The second step refines the scenario by filtering flights from the traffic scenario based on route length, cruise speed, cruise altitude, entry time and the desired ratio of internal to external flights. A solution for achieving the desired ratio of internal to external flights, where internal flights are shorter flights and external flights are longer flights based on a distance threshold, is described. Finally, schedulers are described for shaping the hourly arrival traffic count as a function of time in response to airport capacity constraint or for increasing the traffic demand with respect to the available arrival capacity. Results generated for arrival traffic to the four major airports in the New York Metroplex on a busy day using the two-step procedure are discussed. These results show that traffic scenarios for Multi-Aircraft Control System that meet the Human-in-the-Loop and fast-time simulation requirements can be created automatically following the procedures described in the paper. The automated process will improve the accuracy and efficiency by eliminating the tedious manual process for scenario generation.

Description: This paper presents an encounter-based simulation architecture developed at NASA to facilitate flexible and efficient Detect and Avoid modeling in parametric or tradespace studies on large data sets. The basic premise of this tool is that large-scale input data can be reduced to a set of `canonical encounters' and that using the reduced data in simulations does not lead to loss of fidelity. A canonical encounter is specified as ownship and intruder flight portions potentially resulting in a loss of well clear along with a set of properties that characterize the encounter. The advantages of using canonical encounters include faster simulations, reduced memory footprint, ability to select encounters based on user-specified criteria, shared encounters across multiple teams, peer-reviewed encounters, and a better understanding of the input data set, to name a few.

Description: This paper describes exploratory modeling of an on-demand urban air mobility (UAM) network and sizing of vehicles to operate within that network. UAM seeks to improve the movement of goods and people around a metropolitan area by utilizing the airspace for transport. Aircraft sizing and overall network performance results are presented that include comparisons of battery-electric and various hybrid-electric vehicles that are fueled with diesel, jet fuel, compressed natural gas, and liquefied natural gas (LNG). Hybrid-electric propulsion systems consisting of internal combustion engine-generators, turbine-generators, and solid oxide fuel cells are explored. Ultimately, the "performance" of the UAM network over a day for each of the different vehicle types, propulsion systems, and stored energy sources is described in four parameters: 1) the average cost per seat-kilometer, which considers the costs of the energy/fuel, vehicle acquisition, insurance, maintenance, pilot, and battery replacement costs, 2) carbon dioxide emission rates associated with vehicle operations, 3) the average passenger wait time, and 4) the average load factor, i.e., the total number of seats filled with paying passengers divided by the total number of available seats. Results indicate that the "dispatch model," which determines when and where aircraft are flown around the UAM network, is critical in determining the overall network performance. This is due to the often-conflicting desires to allow passengers to depart with minimal wait time while still maintaining a high load factor to reduce operating costs. Additionally, regardless of the dispatch model, hybrid-electric aircraft powered by internal combustion engines fueled with diesel or LNG are consistently the lowest cost per seat-kilometer. Battery-electric and future technology LNG/solid oxide fuel cell aircraft produce the lowest emissions (assuming the California grid) with LNG-fueled internal combustion engine-powered hybrids producing only slightly more carbon dioxide.

Description: Urban Air Mobility (UAM) is an up and coming topic in the world of aerosciences. A variety of companies, most notably Uber, has begun working towards making air taxis a regular part of day to day life. However, the implementation of this system into society will require a significant amount of work: making helicopters that can handle these flights and operate safely in urban environments, having landing zones, and working out new technologies to lower costs. NASA has also taken interest in this new idea and has formed a focus group of interns to tackle some of these problems. They have started by designing a few concept models for what these air taxis could look like, focusing on low noise, multiple passenger configurations, and the potential for electric or hybrid helicopters. One particular model is known as NR2, or the "Side by Side," which features two rotors spinning in opposite directions. Though these models are purely conceptual at this point, understanding the real-world aerodynamics and performance of this model is crucial to its future development. Using a program known as Rotorcraft Computational Fluid Dynamics (RotCFD), the performance characteristics of the rotors and aircraft, such as the lift, drag, thrust and power can be determined. These simulations can be run in a variety of flight configurations, with hover, forward flight, and climb being focused on in this study. The rotor collective angle can also be changed and used to get results about the lift and drag for the blades and the model body. These simulations can provide information for future model construction and wind tunnel testing.

Description: Abstract and not the Final document is attached. Low Lunar orbit presents a unique thermal environment with high planetary and high solar IR requirements. Orion requires a phase change material heat exchanger (PCM HX) to act as a supplemental heat rejection device (SHReD) during this orbit. As a result, Orion currently uses a PCMHX to meet heat rejection demands in low lunar orbit. This PCM HX weighs 145 lbs, a significant amount of weight on the Crew Module Adaptor. To reduce this weight, a new PCM HX and phase change material is being proposed. This new PCM HX, constructed by Mezzo technologies, was originally designed as a water based PCM HX but is now be repurposed for phase change materials with transition temperatures in Orion's set points and different freeze front propagations. Mezzo's PCM HX utilizes micro tubes which greatly increase the overall heat transfer efficiency allowing for a compact design and significant weight savings. A new phase change material is also being proposed which has a higher latent heat of fusion as well as a higher density. This paper investigates the design, testing, and analysis done on the new Mezzo PCM HX as well as the corresponding phase change material.

Description: NASA's UAS Traffic management (UTM) -TCL-4 focuses on safely enabling large scale small UAS oper- ations in low altitude airspace in dense urban regions. This paper presents an operational architecture of an autonomous unmanned aerial vehicle operating in TCL4. An on-line path planning scheme is proposed which can effectively plan for feasible paths in real time with TCL-4 constraints. An end to end system is designed and tested in high fidelity Reflection architecture which demonstrates the feasibility of the approach.

Description: Computational ice shapes were generated on the boundary layer ingesting engine nacelle of the D8 Double Bubble aircraft. The computations were generated using LEWICE3D, a well-known CFD icing post processor. A 50-bin global drop diameter discretization was used to capture the collection efficiency due to the direct impingement of water onto the engine nacelle. These discrete results were superposed in a weighted fashion to generate six drop size distributions that span the Appendix C and O regimes. Due to the presence of upstream geometries, i.e. the fuselage nose, the trajectories of the water drops are highly complex. Since the ice shapes are significantly correlated with the collection efficiency, the upstream fuselage nose has a significant impact on the ice accretion on the engine nacelle. These complex trajectories are caused by the ballistic nature of the particles and are thus exacerbated as particle size increases. Shadowzones are generated on the engine nacelle, and due to the curvature of the nose of the aircraft the shadowzone boundary moves from lower inboard to upper outboard as particle size increases. The largest particle impinging one the engine nacelle from the 50-bin discretization was the 47 um drop diameter. As a result, the MVD greater than 40 um Appendix O conditions were characterized by extremely low collection efficiency on the engine nacelle for these direct impingement simulations.

Description: Radiative heating computations are performed for high speed lunar return experiments conducted in the Electric Arc Shock Tube (EAST) facility at NASA Ames Research Center. The nonequilibrium radiative transport equations are solved via NASA's in-house radiation code NEQAIR using flow field input from US3D flow solver. The post-shock flow properties for the 10 km/s Earth entry conditions are computed using the stagnation line of a blunt-body and a full facility CFD (Computational Fluid Dynamics) simulation of the EAST shock tube. The shocked gas in the blunt-body flow achieves a thermochemical equilibrium away from the shock front whereas EAST flow exhibits a nonequilibrium behavior due to strong viscous dissipation of the shock by boundary layer. The full-tube flow calculations capture the influence of the boundary layer on the shocked gas state and provide a realistic fluid dynamic input for the radiative predictions. The integrated radiance behind the shock is calculated in NEQAIR for wavelength regimes from Vacuum-UltraViolet (VUV) to InfraRed (IR), which are pertinent to the emission characteristics of high enthalpy shock waves in air. These radiance profiles are validated against corresponding EAST shots. The full-tube simulations successfully predict a sharp radiance peak at the shock front which gets smeared in the test data due to the spatial resolution in the measurements. The full facility based radiance behind the shock shows a slightly better match with the test data in the VUV and Red spectral regions, as compared to that from a blunt-body based predictions. The UV radiance is very similar for both geometries and under-predicts the test behavior. The IR test data matches better with the blunt-body based predictions where the full-tube simulations show a significant over-prediction.

Description: This is both a presented version of NASA's in-flight icing training aids, and a brief discussion of NASA Glenn's two icing-capable facilities that simulate the airframe and engine icing environments. This presentation has been adapted for a Kent State University Aviation Safety Day. The original version was developed in 2006 time frame, and has been presented to both pilots and engineers.

Description: Numerical investigations of the flowfield inside NASA Ames' Electric Arc Shock Tube have been performed. The focus is to simulate the experiments designed to reproduce shock layer radiation layer relevant to Earth re-entry conditions. This paper assess the current computational capability in simulating time-accurate unsteady nonequilibrium flows in the presence of strong shock waves with state-of-the-art physical models. The technical approach is described with preliminary results presented for one specific flow condition. It was found that the axisymmetric source term generates a numerical instability that appears as shock bending. This instability is time dependent which greatly affects the shock speed. Post-shock conditions are discussed and compared to CEA equilibrium prediction and good agreement was obtained close to the test-section and just behind the shock.

Description: The HEEET project was conceived to develop a heatshield with a high performance ablative thermal protection material that can withstand the extreme entry environment produced as a result of rapid deceleration during high speed entry into Venus, Saturn, Uranus or higher speed entry into Earth's atmosphere. Successful maturation of HEEET supports future New Frontiers and Discovery AO's, as well as Flagship and directed missions in the longer term. In addition, HEEET has the potential to evolve and to support re-entry to Earth, for missions such as Mars Sample Return.The primary goal of the HEEET Project was to develop an ablative TPS heat-shield based on woven TPS technology to Technology Readiness Level (TRL) 6. Key evidence to support the TRL evaluation includes: Demonstration of reproducible manufacturing of a dual layer material over a range of thicknesses and integrated on to a heatshield engineering test unit at a scale that is applicable to near term Discovery as the highest priority and future NF missions as secondary priority set of missions. Demonstration of predictable and stable performance of the dual layer TPS over a range of entry environments that are applicable to near term Discovery and NF missions of interest to SMD.Includes completion of coupon arc jet and laser testing and development of a mid-fidelity thermal response model that correlates with test results. Demonstration of flight heatshield system design for a range of sizes and loads that are relevant to near term Discovery and NF missions of interest to SMD. Includes completion of structural testing to validate analytic thermal/structural models and development of a material property database. Includes structural testing of a ~1m Engineering Test Unit under relevant entry loads.

Description: This paper presents results on potential interaction effects from UAM (Urban Air Mobility) operations integrated into current operational scenarios by evaluating if/where/how Traffic alert and Collision Avoidance System (TCAS) alerts are triggered on-board commercial aircraft. A range of operational scenarios are evaluated with combinations of UAM vehicle route, speed, altitude, and direction along the DFW (Dallas-Fort Worth) "spine route." The effect of UAM altitude uncertainty on the above is also explored. The analysis was done for both South flow and North flow configurations of DFW. When UAM operations are deterministic, no TCAS RAs (Resolution Advisories) are issued. However, UAM altitude uncertainties point out geographic areas of concern with the associated severity of interactions.

Description: This paper reports computational analyses and flow characterization studies in a high enthalpy arc-jet facility at NASA Ames Research Center. These tests were conducted using a wedge model placed in a free jet downstream of new 9-inch diameter conical nozzle in the Ames 60-MW Interaction Heating Facility. Both the nozzle and wedge model were specifically designed for testing in the new Laser-Enhanced Arc-jet Facility. Data were obtained using stagnation calorimeters and wedge models placed downstream of the nozzle exit. Two instrumented wedge calibration plates were used: one water-cooled and the other RCG-coated tile plate. Experimental surveys of arc-jet test flow with pitot and heat flux probes were also performed at three arc-heater conditions, providing assessment of the flow uniformity and valuable data for the flow characterization. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested, and comparisons with the experimental measurements. By taking into account nonuniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields, these simulations approximately reproduce the probe survey data and predict the wedge model surface pressure and heat flux measurements.

Description: This presentation covers how a high level overview of the Fuser used on ATD-2.

Description: Overview of NASA Integrated Demand Management (IDM) research into synchronized use of strategic and tactical air traffic management systems describes the initial motivation for the research, summary description of key experiments conducted between 2016 and the present, collaboration with outside partners and stakeholders, and the current status of the research.

Description: The Flight Awareness Collaboration Tool (FACT) is a web-based software tool that provides important information about winter weather operations to airline dispatchers and airport personnel. This document provides instructions on how to operate FACT. It reviews FACT goals, features, functions, controls, and data displays. The manual uses text and screen shots of the screens to guide new users on how to access FACT features. This manual is required for FACT distribution to airlines and airports and is needed as part of the NASA patent process.

Description: This presentation provides an overview of work being done to develop test vectors for the terminal area, in coordination with RTCA Special Committee 228, an organization developing the Minimum Operational Performance Standards (MOPS) for Unmanned Aircraft Systems (UAS) Detect and Avoid (DAA) systems. The work leverages existing encounter data to develop a set of encounters to be used to define and refine both performance-based and functionally-based terminal area MOPS requirements. The encounter set would be used across various organizations supporting MOPS terminal area requirements development to provide some level of consistency in terms of terminal area assumptions. The work will investigate other potentially applicable data sets and make any similarly needed adjustments to arrive at a consolidated set of terminal area encounters.

Description: When optimizing the takeoff sequence and schedule for departures at busy airports, it is important to accurately predict the taxi times from gate to runway because those are used to calculate the earliest possible takeoff times. Several airports like Charlotte Douglas International Airport show relatively long taxi times inside the ramp area with large variations, with respect to the travel times in the airport movement area. Also, the pushback process times have not been accurately modeled so far mainly due to the lack of accurate data. The recent deployment of the integrated arrival, departure, and surface traffic management system at Charlotte airport by NASA enables more accurate flight data in the airport surface operations to be obtained. Taking advantage of this system, actual pushback times and ramp taxi times from historical flight data at this airport are analyzed. Based on the analysis, a simple, data-driven prediction model is introduced for estimating pushback times and ramp transit times of individual departure flights. To evaluate the performance of this prediction model, several machine learning techniques are also applied to the same dataset. The prediction results show that the data-driven prediction model is as good as the machine learning algorithms when comparing various prediction performance metrics.

Description: The newly developed Trajectory Option Set (TOS), a preference-weighted set of alternative routes submitted by flight operators, is a capability in the U.S. traffic flow management system that enables automated trajectory negotiation between flight operators and Air Navigation Service Providers. The objective of this paper is to describe and demonstrate an approach for automatically generating pre-departure and airborne TOSs that have a high probability of operational acceptance. The approach uses hierarchical clustering of historical route data to identify route candidates. The probability of operational acceptance is then estimated using predictors trained on historical flight plan amendment data using supervised machine learning algorithms, allowing the routes with highest probability of operational acceptance to be selected for the TOS. Features used describe historical route usage, difference in flight time and downstream demand to capacity imbalance. A random forest was found to be the best performing algorithm for learning operational acceptability, with a model accuracy of 0.96. The approach is demonstrated for an historical pre-departure flight from Dallas/Fort Worth International Airport to Newark Liberty International Airport.

Description: Detect-and-Avoid (DAA) systems are essential to the safe operations of Unmanned Aircraft Systems, and have the objectives of mitigating collisions with and remaining Well Clear of manned aircraft. This paper analyzes four candidate DAA Well Clear definitions for non-cooperative aircraft using mitigated performance metrics of DAA systems. These DAA Well Clear definitions were proposed in previous work based on their unmitigated collision risk and maneuver initiation range. In this work they are evaluated using safety and operational suitability metrics computed from a large number of representative encounters. Results suggest that although the four candidate DAA Well Clear definitions provide comparable safety, the alerting characteristics give preference for the DAA Well Clear definition without a temporal parameter.

Description: e aerodynamic effects of Cold Soaked Fuel Frost have become increasingly significant as airworthiness authorities have been asked to allow it during aircraft take-off. The Federal Aviation Administration and the Finnish Transport Safety Agency signed a Research Agreement in aircraft icing research in 2015 and started a research co-operation in frost formation studies, computational fluid dynamics for ground de/anti-icing fluids, and de/anti-icing fluids aerodynamic characteristics. The main effort has been so far on the formation and aerodynamic effects of CSFF. To investigate the effects, a generic high-lift common research wind tunnel model and DLR-F15 airfoil, representing the wing of a modern jet aircraft, was built including a wing tank cooling system. Real frost was generated on the wing in a wind tunnel test section and the frost thickness was measured with an Elcometer gauge. Frost surface geometry was measured with laser scanning and photogrammetry. The aerodynamic effect of the frost was studied in a simulated aircraft take-off sequence, in which the speed was accelerated to a typical rotation speed and the wing model was then rotated to an angle of attack used at initial climb. Time histories of the lift coefficient were measured with a force balance. The experiments showed that depending on the ambient temperature the frost may evaporate/melt during the take-off sequence. Lift losses after rotation with CSFF contamination at ambient temperatures of 4 to 7C above freezing point were measured to be 4 to 5 % for roughness values, k/c, below 10(exp -3). For comparison, lift loss tests with typical anti-icing fluids were to roughly equal lift losses. This paper gives an overview of the performed activities.

Description: The newly developed Trajectory Option Set (TOS), a preference-weighted set of alternative routes submitted by flight operators, is a capability in the U.S. traffic flow management system that enables automated trajectory negotiation between flight operators and Air Navigation Service Providers. The objective of this paper is to describe and demonstrate an approach for automatically generating pre-departure and airborne TOSs that have a high probability of operational acceptance. The approach uses hierarchical clustering of historical route data to identify route candidates. The probability of operational acceptance is then estimated using predictors trained on historical flight plan amendment data using supervised machine learning algorithms, allowing the routes with highest probability of operational acceptance to be selected for the TOS. Features used describe historical route usage, difference in flight time and downstream demand to capacity imbalance. A random forest was found to be the best performing algorithm for learning operational acceptability, with a model accuracy of 0.96. The approach is demonstrated for an historical pre-departure flight from Dallas/Fort Worth International Airport to Newark Liberty International Airport.

Description: When optimizing the takeoff sequence and schedule for departures at busy airports, it is important to accurately predict the taxi times from gate to runway because those are used to calculate the earliest possible takeoff times. Several airports like Charlotte Douglas International Airport show relatively long taxi times inside the ramp area with large variations, with respect to the travel times in the airport movement area. Also, the pushback process times have not been accurately modeled so far mainly due to the lack of accurate data. The recent deployment of the integrated arrival, departure, and surface traffic management system at Charlotte airport by NASA enables more accurate flight data in the airport surface operations to be obtained. Taking advantage of this system, actual pushback times and ramp taxi times from historical flight data at this airport are analyzed. Based on the analysis, a simple, data-driven prediction model is introduced for estimating pushback times and ramp transit times of individual departure flights. To evaluate the performance of this prediction model, several machine learning techniques are also applied to the same dataset. The prediction results show that the data-driven prediction model is as good as the machine learning algorithms when comparing various prediction performance metrics.

Description: NASA is currently developing a suite of decision support capabilities for integrated arrival, departure, and surface (IADS) operations in a metroplex environment. The effort is being made in three phases, under NASA's Airspace Technology Demonstration 2 (ATD-2) sub-project, through a strong partnership with the Federal Aviation Administration (FAA), air carriers, airport, and general aviation community. The Phase 1 Baseline IADS capabilities provide enhanced operational efficiency and predictability of flight operations through data exchange and integration, tactical surface metering, and automated coordination of release time of controlled flights for overhead stream insertion. The users of the IADS system include the personnel at the Charlotte Douglas International Airport (CLT) air traffic control tower, American Airlines ramp tower, CLT terminal radar approach control (TRACON), and Washington Center. This paper describes the Phase 1 Baseline IADS capabilities and field evaluation conducted at CLT from September 2017 for a year. From the analysis of operations data, it is estimated that 538,915 kilograms of fuel savings, and 1,659 metric tons of CO2 emission reduction were achieved during the period with a total of 944 hours of engine run time reduction. The amount of CO2 savings is estimated as equivalent to planting 42,560 urban trees. The results have also shown that the surface metering had no negative impact on on-time arrival performance of both outbound and inbound flights. The technology transfer of Phase 1 Baseline IADS capabilities has been made to the FAA and aviation industry, and the development of additional capabilities for the subsequent phases is underway.

Description: This presentation reviews voluntary safety reports received by NASA's Aviation Safety Reporting System pertaining to safety issues related to Ground Operations.

Description: This presentation describes the manner in which the ATD-2 began consuming data from SWIM and gradually built new services to satisfy in its mission. This lessons learned from this work indicate that additional data-rich services will be required in the future. This also led to the development of data pre-processing and mediation services that are now of much interest to the community. The presentation mentions some of the barriers to progress that exist for those seeking to use SWIM flight data, and NASA's desire to share its lessons learned with the aviation community.

Description: Recently, heat transfer correlations based on liquid nitrogen (LN2) and liquid hydrogen (LH2) pipe quenching data were developed to improve the predictive accuracy of lumped node codes like SINDA/FLUINT and the Generalized Fluid System Simulation Program (GFSSP). After implementing these correlations into both programs, updated model runs showed strong improvement in LN2 pipe chilldown modeling but only modest improvement in LH2 modeling. Due to large differences in thermal and fluid properties between the two fluids, results indicated a need to develop a separate set of LH2-only correlations to improve the accuracy of the simulations. This paper presents a new set of two-phase convection heat transfer correlations based on LH2 pipe quenching data. A correlation to predict the bulk vapor temperature was developed after analysis showed that high amounts of thermal nonequilibrium of the liquid and vapor phases occurred during film boiling of LH2. Implemented in a numerical model, the new correlations achieve a mean absolute error of 19.5 K in the predicted wall temperature when compared to recent LH2 pipe chilldown data, an improvement of 40% over recent GFSSP predictions. This correlation set can be implemented in simulations of the transient LH2 chilldown process. Such simulations are useful for predicting the chilldown time and boil-off mass of LH2 for applications such as the transfer of LH2 from a ground storage tank to the rocket vehicle propellant tank, or through a rocket engine feedline during engine startup.

Description: No abstract available

Description: Film cooling is used in a wide variety of engineering applications for protection of surfaces from hot or combusting gases. The design of more efficient film cooling geometries/configurations could be facilitated by an ability to accurately model and predict the effectiveness of current designs using computational fluid dynamics (CFD) code predictions. Hence, a benchmark set of flow field property data were obtained for use in assessing current CFD capabilities and for development of better modeling approaches for these turbulent flow fields where accurate calculation of turbulent heat flux is important. Both Particle Image Velocimetry (PIV) and spontaneous rotational Raman scattering (SRS) spectroscopy were used to acquire high quality, spatially-resolved measurements of the mean velocity, turbulence intensity as well as the mean temperature and root mean square (rms) temperatures in a film cooling flow field. In addition to off-body flow field measurements, infrared thermography (IR) and thermocouple measurements on the plate surface enabled estimates of the film effectiveness. Raman spectra in air were obtained across a matrix of axial locations downstream from a 68.07 mm square nozzle blowing heated air over a range of temperatures (up to TR = 2.7) and Mach numbers (up to M0.9), across a 30.48 cm long plate equipped with three patches of 45 small (~1 mm) diameter cooling holes arranged in a staggered configuration. In addition, both centerline streamwise 2-component PIV and cross-stream 3-component Stereo PIV data at 14 axial stations were collected in the same flows. Only a subset of the data collected in the test program is included in this Part I report and are available from the NASA STI office. The final portion of the data will be published in a future report, Part II, along with CFD predictions of the complex cooling film flow.

Description: This summer internship is focused on using CFD and fluid mechanics to optimize the SRL-ADEPT geometry in an attempt to increase drag and area-effectiveness, and reduce flow separation.

Description: ESA recently flew an entry, descent, and landing demonstrator module called Schiaparelli that entered the atmosphere of Mars on the 19th of October, 2016. The instrumentation suite included heatshield and backshell pressure transducers and thermocouples (known as AMELIA) and backshell radiation and direct heatflux-sensing sensors (known as COMARS and ICOTOM). Due to the failed landing of Schiaparelli, only a subset of the flight data was transmitted before and after plasma black-out. The goal of this paper is to present comparisons of the flight data with calculations from NASA simulation tools, DPLR/NEQAIR and LAURA/HARA. DPLR and LAURA are used to calculate the flowfield around the vehicle and surface properties, such as pressure and convective heating. The flowfield data are passed to NEQAIR and HARA to calculate the radiative heat flux. Comparisons will be made to the COMARS total heat flux, radiative heat flux and pressure measurements. Results will also be shown against the reconstructed heat flux which was calculated from an inverse analysis of the AMELIA thermocouple data performed by Astrium. Preliminary calculations are presented in this abstract. The aerodynamics of the vehicle and certain as yet unexplained features of the inverse analysis and forebody data will be investigated.

Description: No abstract available

Description: No abstract available

Description: The Commercial Aviation Safety Team (CAST) has identified a set of safety enhancements to mitigate the risks of loss of control in-flight (LOCI) accidents and incidents involving commercial transport airplanes. In support of this, NASA has been developing technologies intended to enhance flight crew awareness of airplane systems, attitude, and energy state. This report describes preliminary ideas for a methodology to assess the goodness of onboard airplane energy state and automation mode prediction functions. The methodology is intended to contribute to the goal of moving these prediction technologies to the readiness level required for transition to industry and reduce the technology certification risks. In addition, this report describes a simulation-based approach named CASPEr (Characterization of Airplane State Prediction Error) to characterize the performance of these predictive functions over a wide range of operational conditions. The first exploratory version of this approach is described. The bulk of the report documents the initial results of tests to characterize the performance of an airplane trajectory prediction function. Future reports will give additional performance characterization results for this function and a complete description of the proposed methodology to assess such functions.

Description: This report presents data analysis results for a simulation-based approach named CASPEr (Characterization of Airplane State Prediction Error) to characterize the performance of onboard energy state and automation mode prediction functions for terminal area arrival and approach phases of flight over a wide range of conditions. In particular, the results include quantification of energy state (i.e., altitude and airspeed) prediction performance, models for prediction performance as a function of initial energy state (i.e., initial altitude, airspeed, and weight) and weather factors, and analysis of outlier prediction performance. Wind speed, wind direction, and wind gradient were found to be major factors in energy state prediction performance. Initial energy and gust intensity were also significant factors in airspeed prediction performance. Furthermore, the results suggest that errors in automation mode prediction may be a major contributor to outlier prediction performance.

Description: NASA's Descent System Studies (DSS) Program is studying various concept vehicles to enable landing of heavy payloads on the surface of Mars. While it is desirable to run high-fidelity CFD simulations to accurately assess the aerodynamic and aerothermal effects of various design changes during EDL, it is usually difficult to quickly generate high-quality grids suitable for such analyses. One approach to address this bottleneck in mesh generation is through the use oversetting grids. Although the overset approach is efficient and powerful in solving partial differential equations on complex geometries, new users often find it challenging to apply overset concepts for their simulations. For example, generating hyperbolic grids with sufficient overlap; priority in hole-cutting on multiple overlapping grids; and fixes to assemble overlapping viscous grids at the body surface. The objective of this presentation is to introduce a simple process that combines the advantages of near-body, point-matched, structured grids with oversetting background grids suitable for grid alignment. This approach allows for grids that can be sequenced, reclustering of mesh spacing at the wall, and grid alignment with the bow shock. The current methodology is tested on a Mid-L/D configuration using the overset DPLR code.

Description: The primary objective of this study was to capture pilot feedback and decision-making with regard to proposed, hypothetical, go-around criteria that were developed based on previous research. A secondary objective of the study was to assess crew members' awareness of the aircraft state on approach. An experiment was conducted using Boeing 737-800 and Airbus A330-200 level D full-flight simulators, in which pilots flew multiple approaches which were on the borderline of the proposed go-around criteria at 300 ft. Pilots were instructed that they could either execute a go-around or land the airplane on each run, forcing a decision for the borderline cases at 300 ft. Pilots were instructed to go around if the aircraft was outside of the go-around criteria at 300 ft or if either pilot was uncomfortable with the approach. The results revealed that: 1) the most important factors which drove go-around decision-making during the experiment were airspeed and localizer deviation, 2) the objective data suggested that the 300-ft gate is viable, although many pilots were still uncomfortable with that gate height; perhaps more emphasis on checking stability at 1,000 ft and 500 ft would make more pilots comfortable with the 300-ft go-around gate, 3) allowing for momentary deviations should be considered, and 4) the acceptability of the criteria is highly dependent on given pilot's risk tolerance. Overall, the proposed criteria performed well, and most pilots would find the criteria acceptable with some minor adjustments.

Description: No abstract available

Description: Electronics Boxes with high heat dissipations use a thermal interface material to increase heat transfer to the radiator in a vacuum/space environment. There are lots of materials to choose from, but for Spacecraft applications, there are more than high heat transfer metrics which must be met. Contamination (both particle generation and outgassing), ease of cutting, and removal are just as important metrics in material selection. However, vendor data of material thermal conductance is usually based on a 1" X 1" piece of material under high uniform pressures. Large Electronics boxes almost never have optimal pressures, as they are bolted along the perimeter and leave gaps in the center regions. In order to characterize the relative thermal conductance for large Electronics boxes, an 8" X 8" plate was fabricated to simulate an electronics box bottom and bolted around the perimeter to a cold plate. Various thermal interface materials were inserted between the box and cold plate, and overall thermal conductance's were calculated. A table was generated which compares the full gamut of thermal interface materials for large boxes, from a dry joint to a wet joint. Materials were placed in order of high to low conductance's, so an engineer can compare the benefit of each material in a real-world scenario.

Description: The intermediate wake region of a thick flat plate with a circular trailing edge (TE) is investigated with a direct numerical simulation (DNS). The upper and lower separating boundary layers are both turbulent and are statistically identical; the resulting wake is symmetric in the mean. Earlier research dealt with the near/very-near wake of the same plate (x/D 〈 13.0, x is the streamwise distance from the center of the circular TE and D is the plate-thickness/TE-diameter). In the present investigation the emphasis is on the evolution of shed-vortex structure and turbulence intensity distributions with increasing x; the focus is on the region 20.0 〈 x/D 〈 40.0. Profile similarity in wake velocity statistics is explored.

Description: Ammonia is used in the Starboard 1 (S1) and Port 1 (P1) External Active Thermal Control System (EATCS) to cool the pressurized modules, and some of the external electrical power distribution hardware. Leaks that develop in these critical cooling systems that deplete in-line tanks can ultimately result in loss of cooling, which can have devastating impacts to the mission, science and crew onboard the ISS. A slow ammonia leak was initially observed from the P1 EATCS in 2011, but later in 2013 the leak rate began to accelerate. The ammonia inventory eventually began to decay exponentially, raising concerns that the inventory could drop to levels where the system would not be operational.The Robotic External Leak Locator (RELL) was built and launched to the ISS to detect and help locate ammonia leaks using the ISS Robotic Arm and remote ground operator control without constant crew involvement. RELL pinpointed the ammonia leak to the two flexible jumper hose assemblies connecting one of two fluid loops in one of the three deployable radiators to the P1 EATCS. The ammonia inside the two hose assemblies and that radiator fluid loop was isolated and vented to space in 2017. This stopped the leak and an Extravehicular Activity was conducted to remove the two hose assemblies so they could be returned to ground for further Test, Teardown and Evaluation (TT&E). The purpose of this presentation is to discuss this leakage scenario and the TT&E efforts.

Description: Normally, in order to characterize multilayer insulation installed onto a test tank, the boil-off of the tank is measured and then heat loads from structural and fluid penetrations are calculated from temperature measurements throughout the system. For the Structural Heat Intercept, Insulation, and Vibration Evaluation Rig testing, it was determined that this approach would have significant uncertainties (over 50%) and that another method was needed to characterize the heat load through the blanket. Heat flux sensors are widely used to measure heat loads and characterize insulation systems at room temperature, however, the heat fluxes measured are usually two orders of magnitude higher than high performance MLI. Three different heat flux sensors were initially checked out on a liquid hydrogen calorimeter. One was chosen for actual implementation and 20 sensors were ordered. Of those sensors, calibration was attempted on 7 of the sensors. The results from testing and calibration are discussed.

Description: As the surface system is deployed across the NAS and fully integrated with existing FAA decision support, the roles of both ATC and Operators are expected to change. This will discuss first hand examples of this evolution as experienced at CLT.

Description: In winter snow conditions, aircraft need inspection for deicing service before takeoff. Deicing service is a procedure to remove frost, ice, slush, or snow from aircraft for safe operation. Deicing operations vary by airport in many ways. Some airports have designated deicing zones, whereas some use a closed runway or terminal area to perform the procedure. Nonetheless, deicing operations add extra workloads to controllers, and cause increased taxi traffic on the ground. NASA and Korea Aerospace Research Institute (KARI) have been collaborating to model deicing operations at Incheon International Airport (ICN). This paper describes the deicing model and the study of deicing operations in departure scheduling using fast time simulations. The deicing model uses a heuristic algorithm for deicing zone assignment. In the fast time simulations, the model uses probability distributions derived from actual operation data to model deicing request and deicing zone time. It is envisioned that such a deicing model can be useful in airport surface scheduling to provide decision support and improve traffic management performance in winter snow operations.

Description: Evidence collected and explanation of the metrics used that demonstrate benefit from early electronic scheduling of departing flights from CLT into other airports which leverage Earliest Off Block Times (EOBTs) and Time-Based Flow Management automation.

Description: This presentation describes how the fast-time simualtion and modeling techniques are used in the development of ATD-2 system, especially for surface traffic data anlaysis. This presentation will answer the following questions: What analytical results are most important to communicate to Industry from ATD-2 simulation? What fast-time simulations are currently in the works, including EOBT quality impact study and benefits/costs assessment of ATD-2?

Description: No abstract available

Description: The two decades old high order central differencing via entropy splitting and summation-by-parts (SBP) difference boundary closure of Ols- son & Oliger (1994), Gerritsen & Olsson (1996), and Yee et al. (2000) is revisited. The entropy splitting is a form of skew-symmetric splitting of the nonlinear Euler flux derivatives. Central differencing applied to the entropy splitting form of the Euler flux derivatives together with SBP difference operators will, hereafter, be referred to as entropy split schemes. This study is prompted by the recent growing interest in numerical methods for which a discrete entropy conservation law holds, a discrete global entropy conservation can be proved and/or the numerical method possesses a stable entropy in the framework of SBP difference operators and L2-energy norm estimate. The objective of this paper is to recast the entropy split scheme as the re- cent definition of an entropy stable method for central differencing with SBP operators for both periodic and non-periodic boundary conditions for non- linear Euler equations. Standard high order spatial central differencing as well as high order central spatial DRP (dispersion relation preserving) spatial differencing is part of the entropy stable methodology framework. Long time integration of 2D and 3D test cases is included to show the comparison of this efficient entropy stable method with the Tadmor-type of entropy conservative methods. Studies also include the comparison among the three skew-symmetric splittings on their nonlinear stability and accuracy performance without added numerical dissipations for smooth flows. These are, namely, entropy splitting, Ducros et al. splitting and the Kennedy & Grub- ber splitting.

Description: No abstract available

Description: No abstract available

Description: The current system used by the FAA to schedule arrivals is the Traffic Based Flow Manager (TBFM). It is a centralized system that gives an operator (airline) no influence over scheduled times of arrival assigned to its flights. Future systems for managing arrival scheduling are proposed as distributed systems. Such a system is called upon to give operators influence to schedule and negotiate resources for their flights, and to resolve other technical challenges, such as eliminating a single point of failure. A distributed system for managing diverse air traffic will need the capability of computing a schedule for the given arriving flights in a way that complies with the operational constraints. This paper contributes an algorithm that computes such a schedule. Although developed as part of an effort toward a distributed system, the algorithm itself is neither inherently distributed nor inherently centralized and can be used in either type of system.

Description: This presentation provides an overview of ramp traffic control (RTC) and ramp manager traffic console (RMTC) features of ATD-2 Integrated Arrival, Departure, and Surface (IADS) system and will discuss operational use cases that cover surface metering, notification and optional hold of APREQ (approval request/call for release), EDCT (expected departure clearance time), and ground stops.

Description: This presentation presents the capabilities of the Airspace Technology Demonstration 2 (ATD-2) Integrated Arrival, Departure, and Surface (IADS) system as a surface decision support tool for users, including Air Traffic Control (ATC) personnel working at the tower and Center facilities and airline Ramp personnel. The ATD-2 IADS capabilities include data exchange and integration, modeling and scheduling, surface metering, and departure scheduling for overhead stream insertion of constrained flights.

Description: No abstract available

Description: This paper presents numerical models of boiling in a heated tube using the Generalized Fluid System Simulation Program (GFSSP), a finite-volume-based general-purpose flow network code developed at NASA/Marshall Space Flight Center. The heated tube is discretized into a one-dimensional array of nodes and branches to represent the flow of liquid and vapor in a tube with a prescribed pressure differential. The solid wall is also discretized into solid nodes and conductors to allow for heat transfer between the wall and the fluid. The conservation equations of mass, momentum, and energy of the fluid are solved simultaneously with the energy conservation equation for the solid wall. Two experimental configurations of fluid flowing in a vertical tube have been simulated, one with water and the other with liquid hydrogen. This paper compares experimental data with numerical predictions based on four different published correlations for boiling heat transfer coefficients. Three of these correlations are applicable to the saturated vertical flow conditions of the experiments. One of them is applicable to film boiling and has been used for the liquid hydrogen experiment, which was in film boiling regime. For the case of boiling water, the predictions of wall temperatures using the boiling heat transfer correlations agreed well with the experimental results. However, in the case of boiling hydrogen larger discrepancies were observed between the experimental data and numerical predictions.

Description: The Urban Air Mobility (UAM) Market Study is an in-depth study for ODM market leveraging identified key technicalbarriers to understand community interests and market conditions from all aspects such as regulations, economics,public acceptance, airspace operations and safety.

Description: This presentation reviews voluntary safety reports received by NASA's Aviation Safety Reporting System pertaining to safety issues related to incorrect part installation.

Description: This presentation reviews voluntary safety reports received by NASA's Aviation Safety Reporting System pertaining to Dispatch Operations.

Description: This presentation is to provide an overview of NASA's Unmanned Aircraft Systems (UAS) Traffic Management research and testing. The content presents the background and need for a UTM system and the concept elements incorporated in the approach. The testing conducted within the project, the architecture, and overall impact of the research is presented as well.

Description: In response to NTSB Safety Recommendation A-14-043, the FAA was asked to task a panel of human factors, aviation operations, and aircraft design specialists, such as the Avionics Systems Harmonization Working Group (ASHWG), to develop design requirements for context-dependent low energy alerting systems for airplanes engaged in commercial operations. This recommendation is in association to the July 6, 2013, accident involving a Boeing 777-200ER, Korean registration HL7742, operating as Asiana Airlines flight 214, which was on approach to runway 28L when it struck a seawall at San Francisco International Airport (SFO), San Francisco, California. The FAA asked for human factor support from NASA in developing design requirements for context-dependent low energy alerting systems for airplanes engaged in commercial operations. Recently the ASHWG chair asked for continued support in examining flightcrew alert response timing and requested that NASA update the previous working paper on this subject. This product/paper will be provided to the ASHWG as part of the ongoing assignments from each of the ASHWG members in support of developing requirements and guidance for context-dependent low energy alerting systems for airplanes. The ASHWG is made up of interested parties from government and industry.

Description: This is a continuation of part 1 discussion of the data used by ATD-2 analysts. This session will also provide an opportunity for the community input on any additional tech transfer needs for this capability.

Description: This paper presents a set of experiments designed to assess the viability of using a smaller Detect and Avoid (DAA) volume for large Unmanned Aircraft Systems (UAS) when they are trying to remain well clear of non-cooperative visual flight rules (VFR) aircraft, in compliance with Federal regulations. The current DAA volume was defined for both cooperative and non-cooperative VFR traffic by the work of RTCA Special Committee 228 in 2017, in what is referred to in this paper as the Phase 1 standards. Subsequent work by the committee has been focused on enabling operations by smaller UAS that cannot carry the heavy radars required for the Phase 1 DAA Minimum Operational Performance Standards (MOPS). The work discussed in this paper will explore whether a Phase 1 UAS using a Phase 1 radar can use the reduced non-cooperative DAA alerting volume being studied for smaller, slower Phase 2 UAS without significantly degrading system safety. The study uses UAS models and background traffic from previous Phase 1 and Phase 2 research to run an unmitigated simulation that will examine alerting performance using different DAA well clear definitions. The primary metrics are also tied to the alerting performance of the DAA system, and include average alerting times, probabilities of missed and late alerts, and the probability of a near mid-air collision given a loss of "well clear," as defined by the DAA system. Results are expected to help RTCA make the determination whether or not the DAA well clear definition for Phase 1 UAS can be reduced for non-cooperative VFR aircraft.

Description: The present research explored whether the implementation of a letter of agreement (LOA), or pre-established written terms of engagement, would reduce controller communication associated workload in a HITL study simulating a near-term UAM infrastructure with varying traffic levels. Current helicopter routes, including modified versions, and communication procedures were outlined in the LOA. Time spent communicating was reduced under both conditions featuring a LOA, for current and modified routes, compared to present day procedures without a LOA. Results suggest that utilizing current-day helicopter routes and implementing a LOA may prove beneficial for near-term low-density and low-tempo UAM operations.

Description: No abstract available

Description: The NASA Traffic Aware Strategic Aircrew Requests (TASAR) concept offers onboard automation that advises the pilot of traffic compatible route modifications that would be beneficial to the flight. The Traffic Aware Planner (TAP) is the onboard automation component of TASAR. TAP was installed on three Alaska Airlines 737-900ER aircraft and used to conduct an operational evaluation of TASAR between July 24, 2018 and April 30, 2019.

Description: The increasing interest in low-altitude unmanned aerial vehicle (UAV) operations is bringing along safety concerns. Performance of small, low-cost UAVs drastically changes with type, size and controller of the vehicle. Their reliability is lower when compared to reliability of commercial aircrafts, and the availability of on-board sensors for health and state awareness is extremely limited due to their size and propulsion capabilities. Uncertainty plays a dominant role in such a scenario, where a variety of UAVs of different size, propulsion systems, dynamic performance and reliability enters the low-altitude airspace. Unexpected failures could have dangerous consequences for both equipment and humans within that same airspace. As a result, a number of research works and methodologies are being proposed in the area of UAV dynamic modeling, health and safety monitoring, but uncertainty quantification is rarely addressed. Thus, this paper pro- poses a perspective towards uncertainty quantification for autonomous systems, giving special emphasis to a UAV health monitoring application. A formal approach to classify uncertainty is presented; it is utilized to identify the uncertainty sources in UAVs health and operations, and then map uncertainty within a predictive process. To show the application of the methodology proposed here, the design of a model-based powertrain health monitoring algorithm for small-size UAVs is used as case study. The example illustrates how the uncertainty quantification approach can help the modeling strategy, as well as the assessment of diagnostic and prognostic performance.

Description: This presentation summarizes the technical development of low SWaP sensor in the DAA working group, SC-228.

Description: Free-Flight CFD capability has been implemented into the finite-volume solver US3D under the Entry Systems Modeling project. Several simulations of ballistic range experiments have been performed in order to validate the simulation software and methodology. Extension of the software to flight scale trajectories with varying freestream conditions has been carried out. Results show promising ability to predict vehicle behavior as compared to flight. Finally, a multi-body free-flight capability has been developed to generalize the single-body free-flight solver to study multiple bodies in proximal flight.

Description: The new features for the ATD-2 Ramp Traffic Console (RTC) and Ramp Manager Traffic Console (RMTC) released in IADS software version 4.4 are summarized here for training and documentation purposes.

Description: NASA's Airspace Technology Demonstration-3 (ATD-3) is the applied traffic flow management activity, and third in the series of ATD projects. ATD-3 provides a suite of en route automation tools, both ground and flight-deck based, that focus on improving the efficiency of en route operation from initial cruise to arrival into the Terminal Radar Approach Control (TRACON). Dynamic Routes for Arrivals in Weather (DRAW) is a technology in the ATD-3 suite that is designed to provide Traffic Managers with a capability to efficiently manage arrival traffic flow and help sustain metering operations when weather is impacting arrivals into major airports. DRAW mitigates convective weather impact on arrival metering operations by providing tools to Traffic Managers that enable efficient reroutes free of convective weather conflicts, and integrated with the arrival metering schedule(s).

Description: Airspace Technology Demonstration 2 (ATD-2) sub-project conducted a Human-in-the-Loop (HITL) simulation to assess Ramp Controllers ability to deliver aircraft to the spot within the compliance window (+/- 5 min) under various metering conditions. Compliance at the spot was similar between the different metering conditions ranging between 83% - 85% and increased to 92% - 99% when aircraft were initially compliant with gate advisories. Metering benefits that exist in the field did not appear in the simulation due to simulation artifacts such as gate holding departures in Baseline, which effectively metered the demand. The combined Target Off-Block Time (TOBT) +Target Movement Area entry Time (TMAT) condition resulted in higher workload on the Workload Assessment Keypad (WAK) than the Baseline and TOBT alone conditions, and lower situation awareness than the Baseline condition. Metering at Dallas/Fort Worth International Airport (DFW) with TOBT only or TMAT only could be equally effective, and either would be a better option than TOBT + TMAT due to increased workload and reduced situation awareness.

Description: Airspace Technology Demonstration 2 (ATD-2) sub-project conducted a human-in-the-loop (HITL) simulation to assess various strategies for Ramp controllers to deliver aircraft to the spot at a specified time. Results show that the rate of compliance with the spot time improved when Ramp controllers first complied with a gate hold advisory for pushing aircraft off the gates. Results also show that Ramp controller workload was lower when they only had to focus on complying with the gate hold advisories.