ALBERT

Description: Present understanding of planetary atmospheres is surveyed. The formation of the planets and their atmospheres is briefly reviewed, and attention is given to the compositions of the atmospheres of earth, Venus, and Mars, the outer planets, and Titan. Lists of the individual atmospheric gases and their concentrations are included.

Description: This design course is directed to studying problems related to mobile exploration of the surface of Mars. Constraints on the vehicles considered are set by the payload and performance currently envisioned by mission analysis carried out previously at the Jet Propulsion Laboratory. The students are given full flexibility to examine those aspects which suit their interests and background. There are no regularly scheduled class lectures. Weekly review meetings are held with personnel from the Jet Propulsion Laboratory, and students use JPL resources as required.

Description: The Moon is a body rich in natural resources and full of intriguing scientific questions, and it will most certainly play a central role in the growth of near-Earth and deep space ventures of the twenty-first century. The LOP mission is an example of one way to catalog the Moon's natural resources and to answer lunar science questions in parallel. In a realistic planetary exploration program, this mission must compete with other interesting planetary missions and therefore the LOP must be as low cost and adaptable as possible. This flexibility is reflected in the LOP's heavy design emphasis on modularity. The LOP mission can easily be expanded to include new technologies, and additional orbiters could be launched into lunar orbit to provide a constellation of remote-sensing platforms. This design thus projects a broad range of possibilities for continued lunar exploration in the next century.

Description: The vector magnetograph of the Okayama Astrophysical Observatory is fed to the 65 cm solar coude telescope with a 10 m Littrow spectrograph. The polarimeter put at the telescope focus analyzes the incident polarization. Photomultipliers (PMT) at the exit of the spectrograph pick up the modulated light signals and send them to the electronic controller. The controller analyzes frequency and phase of the signal. The analyzer of the polarimeter is a combination of a single wave plate rotating at 40 Hz and a Wallaston prism. Incident linear and circular polarizations are modified at four times and twice the rotation frequency, respectively. Two compensators minimize the instrumental polarization, mainly caused by the two tilt mirrors in the optical path of the telescope. The four photomultipliers placed on the wings of the FeI 5250A line give maps of intensity, longitudinal field and transverse field. The main outputs, maps of intensity, and net linear and circular polarizations in the neighboring continuum are obtained by the other two monitor PMTs.

Description: Through the Surveyor 3 and 7, and Apollo 11-17 missions a knowledge of the mechanical properties of Lunar regolith were gained. These properties, including material cohesion, friction, in-situ density, grain-size distribution and shape, and porosity, were determined by indirect means of trenching, penetration, and vane shear testing. Several of these properties were shown to be significantly different from those of terrestrial soils, such as an interlocking cohesion and tensile strength formed in the absence of moisture and particle cementation. To characterize the strength and deformation properties of Lunar regolith experiments have been conducted on a lunar soil simulant at various initial densities, fabric arrangements, and composition. These experiments included conventional triaxial compression and extension, direct tension, and combined tension-shear. Experiments have been conducted at low levels of effective confining stress. External conditions such as membrane induced confining stresses, end platten friction and material self weight have been shown to have a dramatic effect on the strength properties at low levels of confining stress. The solution has been to treat these external conditions and the specimen as a full-fledged boundary value problem rather than the idealized elemental cube of mechanics. Centrifuge modeling allows for the study of Lunar soil-structure interaction problems. In recent years centrifuge modeling has become an important tool for modeling processes that are dominated by gravity and for verifying analysis procedures and studying deformation and failure modes. Centrifuge modeling is well established for terrestrial enginering and applies equally as well to Lunar engineering. A brief review of the experiments is presented in graphic and outline form.

Description: The main purpose of the Halogen Lamp Experiment (HALEX) was to investigate the operation of a halogen lamp during an extended period in a microgravity environment and to prove its behavior in space. The Mirror Heating Facilities for Crystal Growth and Material Science Experiments in space relies on one or two halogen lamps as a furnace to melt the specimens. The HALEX aim is to verify: full power operation of a halogen lamp for a period of about 60 hours; achievement of about 10% of its terrestrial life span; and operation of the halogen lamp under conditions similar to furnace operation.

Description: Some of the design problems that are now being addressed in consideration of a microcontroller for the upcoming GAS payload are discussed. Microcontrollers will be used to run the experiments and to collect and store the data from those experiments. Some of the requirements for a microcontroller are to be small, lightweight, have low power consumption, and high reliability. Some of the solutions that were developed to meet these design requirements are discussed. At present, the experiment is still in the design stage and the final design may change from what is presented here. The search for new integrated circuits which will do all that is needed all in one package continues.

Description: Spectroscopic and spectrophotometric data on the atmospheres of comets, the outer planets, and Titan at ultraviolet to near-infrared wavelengths were acquired. These data support an effort aimed at characterizing the physical properties and distribution of aerosol particles in the atmospheres of these bodies. New spectrophotometry was acquired of Uranus at 0.2 lambda 0.3 micrometer with IUE; archival IUE spectrophotometry of Uranus and Neptune in this wavelength range was acquired and recalibrated. New estimates of radiometric Bond albedos and global energy budges of Uranus, Neptune and Titan were published.

Description: Infrared observations were made of the outer planet satellites. These data provide vital information about the thermophysical properties of satellite surfaces, including internal heat sources for Io. Observations include both broad and narrow band measurements in the 2 to 20 micrometer spectral range. Types of observation and target priority were determined to make maximum use of existing data from Voyager and other missions, on-going and planned missions such as Galileo, were supported and techniques and data for planning new missions and instrumentation were developed.

Description: Multipolarized airborne Synthetic Aperture Radar (SAR) data were acquired over a largely agricultural test site near Macomb, Illinois, in conjunction with the Shuttle Imaging Radar (SIR-B) experiment in October 1984. The NASA/JPL L-band SAR operating at 1.225 GHz made a series of daily overflights with azimuth view angles both parallel and orthogonal to those of SIR-B. The SAR data was digitally recorded in the quadpolarization configuration. An extensive set of ground measurements were obtained throughout the test site and include biophysical and soil measurements of approximately 400 agricultural fields. Preliminary evaluation of some of the airborne SAR imagery indicates a great potential for crop discrimination and assessment of canopy condition. False color composites constructed from the combination of three linear polarizations (HH, VV, and HV) were found to be clearly superior to any single polarization for purposes of crop classification. In addition, an image constructed using the HH return to modulate intensity and the phase difference between HH and VV returns to modulate chroma indicates a clear capability for assessment of canopy height and/or biomass. In particular, corn fields heavily damaged by infestations of corn borer are readily distinguished from noninfested fields.

Description: Multipolarization Synthetic Aperture Radar (SAR) data from the NASA/JPL aircraft SAR were used in conjunction with LANDSAT Thematic Mapper (TM), Thermal Infrared Multispectral Scanner (TIMS), and Airborne Imaging Spectrometer (AIS) data as part of a three-year research program to evaluate the utility of remote sensing measurements for analysis of sedimentary basins. The purpose of this research effort is to construct stratigraphic columns, map variations in the lithology, geometry, and structure of sedimentary rocks in the Wind River/Bighorn Basin area, Wyoming, and to integrate remote sensing data with conventional rain models of basin formation and evolution.

Description: Several digital data processing techniques were evaluated in an effort to identify and map active/abandoned, partially reclaimed, and fully revegetated surface mine areas in the central portion of Logan County. The TM data were first subjected to various enhancement procedures, including a linear contrast stretch, principal components and canonical analysis transformations. At the same time, four general procedures were followed to produce six classifications as a means of comparing the techniques involved. Preliminary results show that various feature extraction/data reduction techniques provide classification results equal or superior to the more straightforward unsupervised clustering technique. Analyst interaction time for labelling clusters is reduced using the canonical analysis and principal components procedures, though the canonical technique has clearly produced better results to date.

Description: Airborne Imaging Spectrometer data from Mono Lake, California, were studied in order to establish spectral radiance of test areas under solar illumination. The objective is to provide a method of atmospheric correction for major absorbers from the spectrometer data themselves. Crucial to the analysis is radiometric calibration of the instrument. Good agreement is found between calculated and measured radiances for uniform surface targets (beaches), but simulations of atmospheric properties with LOWTRAN lead to unreasonably low values of atmospheric precipitable water. Absorptions from carbon dioxide are not detected in the AIS data, but are strongly present in the LOWTRAN model. The apparent low contrast of all atmospheric absorption bands leads to a study of contamination from overlapping spectral orders in the AIS data. The suspected contamination is shown unambiguously to be present beyond approximately 1500 nm and consists of an extra radiance term including atmospheric bands from the delta/2 wavelength interval. A rigorous removal of the unwanted spectral contamination does not seem possible for any data taken in the rock mode. Rough estimates for tree-mode observations might be pieced together is a suitable after-the-fact radiometric claibration of the instrument can be formulated.

Description: Telescopic observations were made of gases and plasmas in the Jupiter system, and related phenomena such as the recently-discovered sodium atmosphere of Mercury. Sodium absorption in Io's atmosphere was observed to distances as large as 5 Io radii during the mutual-eclipse season of the Jovian satellites. Analysis of Jovian disk spectra has proceeded, as planned, from an emphasis on the H2 ortho-para ratio to analysis of methane absorptions and determination of cloud structure. Several 2-channel photometers were constructed in 1978 for the Uranus event at which the rings were discovered and a smaller, single-channel unit was built more recently. Although the photometers themselves are still fully usable, the data-acquisition systems have major deficiencies.

Description: It is proposed to measure the reflectance spectra of the icy satellites of Jupiter, Saturn and Uranus in the spectral region 1.8 to 2.4 micrometers. These observations use the new Cooled Grating Array Spectrometer using a 32-element InSb photodiode array detector and produce spectra of higher resolution and precision than any data yet obtained; the ultimate scientific objective is to search for the signatures of methane clathrate, ammonium hydroxide or carbon monoxide clathrate (compounds predicted to exist on icy surfaces in the outer solar system by several theories of formation of these bodies) in the region of the spectrum where water ice has a relative maximum in reflectance. At the very least, these data will allow upper limits to be placed on the amount of these chemical species that can be present. The specific targets is Europa, Ganymede, Enceladus, Ariel and Titania, bodies that have the highest probability of having some or all of these volatiles on their surface according to current formation models.

Description: An Infrared Camera was built for astronomical observations and for testing arrays for satellite based work. The detectors are sensitive to mid infrared wavelengths. The camera was tested at the University of Arizona 61 and 90 inch telescopes and the NASA IRTF. These tests have demonstrated a sensitivity consistent with photon shot noise with an approximately 10% quantum efficiency for each pixel when the camera was used with a 1.6% spectral filter or when used with a Fabry-Perot having a resolving power of 2000. Initial measurements of read out noise, dark current, cross talk, and hysteresis were made. The detector chip in current use is a hybrid array manufactured by the Hughes Aircraft Company. Because part of the goal was to develop and advance technology, it was decided to work with a switched MOSFET array. This architecture is very promising, and the detector parameters will be quantified carefully.

Description: Preliminary results from the Hughes 58 x 62 gallium-doped silicon infrared array are presented. The device functioned predictably and repeatedly at the low temperatures for the Space Infrared Telescope Facility (SIRTF). Power dissipation was reduced to acceptable levels while still maintaining the device speed. The infrared response was excellent and the degree of anomalous effects was compatible to conventional photoconductors.

Description: The fabrication of antimony doped silicon (Si:Sb) detector arrays are described for use in 30 micron infrared imaging applications. The operation of the multiplexer readout circuit which will be used for this application is also described.

Description: The initial testing performed on the Hughes Metal Oxide Semiconductor Direct Readout (MOS DRO) with a Si:In extrinsic infrared array is described. The testing to date was of a screening nature and the results are primarily qualitative rather than quantitative. At a later date the performance optimization phase will be initiated. An encouraging result is that this response is strongly dependent on the detector temperature, to the extent that thermal transients introduced during the chip readout will affect the performance. A responsivity of 1 A/W at 2.2 microns with a bias of 15 volts, which is well below what is optimum bias, was obtained.

Description: A description of the design and performance of an imaging spectrometer intended for operation in the 7 to 14 micron wavelength range is presented. It is based upon a 16 by 16 element Si:Bi hybrid array, a circular variable filter wheel, and a microcomputer data acquisition system. The spatial-spectral photometric performances were evaluated in the laboratory as well as field tested at astronomical observatories. The performance characteristics of the system are presented as well as laboratory and astronomical images.

Description: Hybrid silicon Infrared Charge Coupled Devices (IRCCDs) are evaluated for use as viable astronomical detectors. A Si:In photoconductor array which is bump-bonded to a silicon multiplexer is described. A summary of the device parameters is given.

Description: The general architecture of the imaging array, some merits of HgCdTe-on-sapphire as a detector material, and the current status of the laboratory tests and the Short Wave Infrared (SWIR) camera are described.

Description: Highlights of the results obtained on arsenic-doped silicon blocked impurity band (BIB) detectors and arrays since the invention of the BIB concept a few years ago are presented. After a brief introduction and a description of the BIB concept, data will be given on single detector performance. Then different arrays that were fabricated will be described and test data presented.

Description: The 32 x 32 HgCdTe array manufactured by Rockwell International was proven to be a highly competitive detector type for use at wavelengths shorter than 2.5 microns. The goal of a K=+16 sky survey using this array attached to the Steward Observatory Transit Telescope is clearly within reach. The detector material exhibits high quantum efficiency and low dark currents indicating that its usefulness may extend beyond its use with a CCD readout on groundbased telescopes.

Description: In infrared astronomy observations, one of the key detector performance parameters is the dark current which, together with the optics, establishes the fundamental limit of a space-based instrument. This technical note summarizes an effort to measure dark current performance of the MLA/Short Wave Infrared photovoltaic HgCdTe array (2.5 micron cutoff) at temperatures from 65 to 120 K. The preliminary results indicate that dark current decreased systematically to 100 K, then the value became measurement-limited at about 3.0 E-18 A/pixel, or 19 electrons/sec/pixel.

Description: A program of testing aimed at the evaluation of systems that have the potential to provide the level of performance required for use in space-based instruments was undertaken and their usefulness appraised for astronomy. The results of the first phase of the program to characterize selected pixels of a HgCdTe photovoltaic array detector were reported.

Description: The Infrared Space Observatory (ISO), an approved and funded project of the European Space Agency (ESA), will be an astronomical satellite observatory operating at wavelengths from 3 to 200 microns. The ISO Project and its status are summarized. The overall goals are outlined, the scientific instruments are described, and the current activities are summarized.

Description: The Infrared Space Observatory (ISO) satellite will contain a 60 cm telescope. A 4 faces pyramid mirror feeds each experiment with a 3 arc minute part of the telescope field of view. The camera system is described. The arrays for the 3 to 5 and 5 to 17 micron channel are also discussed.

Description: Experience gained in operating infrared detector arrays for high sensitivity astronomical applications at the University of Rochester are summarized. Progress made in operating the 32 x 32 InSb array with bump-bonded Silicon CCD readout is described. Astronomical work done with the 32 x 32 camera is also described. Plans for the future, including improvements for the 32 x 32 camera system as well as implementing a new generation of 58 x 62 InSb array using switched-MOSFET direct readout multiplexing system in the place of the older CCD technology is discussed.

Description: Bolometers are still the detectors of choice for low background infrared observations at wavelengths longer than 200 microns. In the low background limit, bolometers become more sensitive as their operating temperature decreases, due to fundamental thermodynamic laws. The adiabatic demagnetization technique was evaluated by building a bolometer detection system operating at a wavelength of 1 millimeter for use at a ground based telescope. The system was fit checked at the telescope and is expected to take its first data in November, 1985.

Description: Photovoltaic indium antimonide (PV InSb) detector technology has matured over the past several years to enable a wide variety of applications to use this high-performance detector material to advantage. The operating conditions for most of the applications to date for back-side illuminated PV InSb arrays have encompassed focal plane temperatures ranging from 40 to approximately 95 K, with the majority in the narrower range between 60 and 80 K. Background flux conditions have ranged from 10 to the 10th power ph/sq cm/sec to 10 to the 16th power ph/sq cm/sec, most typically between 10 to the 12th power and 10 to the 14th power ph/sq cm/sec. Appropriately, the array parameters were optimized for maximum performance over these temperature and background ranges. The key parameters which were peaked in this process were the resistance-area product of the detectors and their quantum efficiency. The Space Infrared Telescope Facility (SIRTF) Infrared Array Camera requirements, however, present very low temperature and background operating conditions, plus the need for very high signal to noise ratios. Preliminary analysis indicates that back-side illuminated PV InSb arrays can be optimized for operation under these conditions, and some performance projections will be presented.

Description: Bolometer elements were built and tested using NTD germanium and ion-implanted Si thermometer elements. The thermal links were made using aluminum wires and NbC(x)N(y) coated carbon fibers. The temperature dependence of the detector resistance, lead thermal conductivity, and heat capacity were measured. The dependence of the detector resistance on applied electric field was also measured. This, combined with the current-voltage curve for the detector, allowed the calculation of the detector responsivity. Known amounts of energy were deposited into the detector by allowing X-rays from the decay of Fe-55 to be thermalized in the detector. In the best-measured case, the predicted pulse height/measured height was 1.04 + or - .05. The noise at frequencies above 25 Hz in the NTD Ge was near that predicted by thermodynamics. The noise below 25 Hz has a 1/f character and may be in the carbon fiber/bolometer junction. The implanted detectors show some 1/f noise which depends on the total thermometer volume. Comparison between noise measurements and theory will be presented.

Description: The first IR Detector Technology Workshop took place at NASA Ames Research Center on July 12 and 13, 1983. The conclusions presented at that meeting are still valid. More was learned about the physics of hopping conduction at very low temperatures which will be important for bolometer design and operation at ever decreasing temperatures. Resistivity measurements were extended down to 50 mK. At such low temperatures, precise knowledge of the neutron capture cross sections sigma (sub n) of the various Ge isotopes is critical if one is to make an accurate prediction of the dopant concentrations and compensation, and therefore resistivity, that will result from a given irradiation. An empirical approach for obtaining the desired resistivity material is described and the process of conducting a set of experiments which will improve the knowledge of the effective sigma (sub n) values for a given location in a particular reactor is discussed. A wider range of NTD Ge samples is now available. Noise measurements on bolometers with ion implanted contacts show the no 1/f noise component appears down to 1 Hz and probably lower.

Description: Ge:Be photoconductors were optimized for the 30 to 50 micron wavelength range. Crystal growth of detector quality material requires good control of both the Be and residual impurity doping. Detective quantum efficiencies of n sub d = 46% at 5 A/W were achieved at a photon background of 10 to the 8th power p/s. The responsivity of Ge:Be detectors can be strongly temperature-dependent when the residual shallow levels in the material are closely compensated. Transient responses on the order of approximately 1 second were observed in some materials. The role of residual shallow impurities on the performance of photoconductors doped with semi-deep and deep impurities is discussed.

Description: One of the four focal plane instruments of the Infrared Space Observatory (ISO) is ISOPHOT, a photopolarimeter for the wavelength region 3 to 200 microns. Each experiment occupies a quadrant of the focal plane. The telescope beam is directed into each experiment by means of a pyramid mirror and by tilting the satellite. The diameter of the unvignetted field of view is 3 arcmin or 7.85 mm in the focal plane (1 mm = 23 arcsec). The temperatures provided are 3 K for cooling the detector systems and 8 K for the experiment structure. Available detectors are described along with the current status of the experiment.

Description: A new approach to infrared detector readout has appeared with the development of integrating JFET amplifiers. This brief progress report includes results on the operation of commercially available devices at a temperature of 40 K, on their sensitivity and on an effort to develop a new JFET with properties optimized for cryogenic applications. Even with presently available devices it will be shown that for applications such as the Space Infrared Telescope Facility (SIRTF), the most strigent sensitivity requirements of noise currents as low as 1 electron/sec in less than 100 seconds of integration can be met.

Description: The Space Infrared Telescope Facility (SIRTF) is envisioned as a next generation space observatory for observations between 2 and 700 microns. In order to address many of the important scientific questions in areas such as cosmology, star formation, and galaxy evolution, infrared detectors of unparalleled sensitivity will be required. Dark current measurements are described for a number of different discrete photoconductive detectors that may be of importance at the very low backgrounds expected with SIRTF.

Description: Requirements for background-limited (BLIP) detectors are discussed in terms of number of photons falling on each pixel, dark current, high detective quantum efficiencies, large numbers of pixels, and array size.

Description: The Space Shuttle Challenger was observed spectroscopically in two passes over Maui during the Spacelab 2 mission. Through most of one of the passes strong bands centered at 1.52 and 1.69 microns, tentatively identified as OH bands, were detected. The average luminosity of the Shuttle in the 1.45 to 1.75 micron range was roughly equal to that of a star of magnitude +5.5. The luminosity was much lower during part of the pass. Spectra from 0.65 to 2.4 microns were obtained during the second pass. These showed that most of the nonthermal emission is in the 1.2 to 2.2 micron range as would be expected for vibrationally excited OH.

Description: In order to understand the origin and distribution of the biogenic elements and their compounds in the solar system, it will be necessary to study material from many classes of objects. Chemical, elemental, and isotopic measurements of returned samples of comets, asteroids, and possibly extra-solar system dust clouds would provide information on a particularly important class: the primitive objects. Extraterrestrial micron-sized particles in the vicinity of earth are one source of such materials that might otherwise be inaccessible. The Space Station appears to be an eminently suitable platform from which to collect and detect these various particles. The primary challenge, however, is to collect intact, uncontaminated particles which will be encounted at tens of kilometers per seconds. A concept for a micrometeoroid detector that could be deployed at a Space Station has been developed which uses a large area detector plate implanted with acoustic transducers. When an impact event occurs, the resulting signal is subjected to spectral analysis providing positive detection, momentum information, and angle of incidence. The primary advantage of this detector is the large area which increases the probability of measuring events.

Description: The recent Voyager flyby of Titan produced evidence for at least nine organic compounds in that atmosphere that are heavier than methane. Several models of Titan's atmosphere, as well as laboratory simulations, suggest the presence of organics considerably more complex that those observed. To ensure that the in situ measurements are definitive with respect to Titan's atmosphere, experiment concepts, and the related instrumentation, must be carefully developed specifically for such a mission. To this end, the possible composition of the environment to be analyzed must be bracketed and model samples must be provided for instrumentation development studies. Laboratory studies to define the optimum flight experiment and sampling strategy for a Titan entry probe are currently being conducted. Titan mixtures are being subjected to a variety of energy sources including high voltage electron from a DC discharge, high current electric shock, and laser detonation. Gaseous and solid products are produced which are then analyzed. Samples from these experiements are also provided to candidate flight experiments as models for instrument development studies. Preliminary results show that existing theoretical models for chemistry in Titan's atmosphere cannot adequetely explain the presence and abundance of all trace gases observed in these experiments.

Description: The airborne L-band synthetic aperture radar (SAR) collected multipolarization calibrated image data over an irrigated agricultural test site near Fresno, CA, on March 6, 1984. The conclusions of the study are as follows: (1) the effects of incidence angle on the measured backscattering coefficients could be removed by using a correction factor equal to the secant of the angle raised to the 1.4 power, (2) for this scene and time of year, the various polarization channels were highly correlated such that the use of more than one polarization added little to the ability of the radar to discriminate vegetation type or condition; the exception was barley which separated from vineyards only when a combination of like and cross polarization data were used (polarization was very useful for corn identification in fall crops), (3) an excellent separation between herbaceous vegetation (alfalfa, barley, and oats) or bare fields and trees in orchards existed in brightness was well correlated to alfalfa height or biomass, especially for the HH polarization combination, (5) vineyards exhibited a narrow range of brightnesses with no systematic effects of type or number of stakes nor of number of wires in the trellises nor of the size of the vines, (6) within the orchard classes, areal biomass characterized by basal area differences caused radar image brightness differences for small to medium trees but not for medium to large trees.

Description: Two uncalibrated synthetic aperture radar (SAR) scenes from Death Valley, California, and two uncalibrated scenes from Owens Valley, California, were used to test a technique to identify and separate the primary factors associated with multipolarized radar image sets. Unique to the technique is the concept that varied types of radar polarization signatures are a result of the interaction of a few physical factors (e.g., roughness, volume scattering, and dielectric constant). Thus, the varied signatures observed in an image reflect the interaction between these factors. The objectives are to first separate the interaction of factors directly influencing the measurement and to attempt to identify these factors. Interpretation of the SAR image sets proceeds by testing models that hypothesize the cause and effect relations between those factors directly affecting the radar measurement and those features of interest to the interpreter. The results of our analysis indicated two consistent endmember types over all four image scenes. These types are defined by a high flat polarized signature near a level of 255 DN and a low level flat signature near 0 DN for all polarizations. Four other endmember types were also isolated. The spatial distribution of these endmember types indicates possible correspondence to surface volume scattering and changes in surface dielectric. However, the shapes of these endmember types were different from scene to scene.

Description: Imaging radar backscatter in continuously forested areas contains information about the forest canopy; it also contains data about topography, landforms, and terrain texture. For purposes of radar image interpretation and geologic mapping researchers were interested in identifying and separating forest canopy effects from geologic or geomorphic effects on radar images. The objectives of this investigation was to evaluate forest canopy variables in multipolarization radar images under conditions where geologic and topographic variables are at a minimum. A subsidiary objective was to compare the discriminatory capabilities of the radar images with corresponding optical images of similar spatial resolution. It appears that the multipolarization images discriminate variation in tree density, but no evidence was found for discrimination between evergreen and deciduous forest types.

Description: While radar does not provide detailed begetation discrimination, it provide the means to separate areas of different moisture conditions. Thus, the use of LANDSAT Thematic Mapper (TM) in conjunction with the microwave data was attempted. If successful, information on shoreline cover, emergent wetland vegetation and extent, and submerged grassbeds would provide much needed data for planning and maintenance of wetlands. Originally, the goal was to determine the accuracy with which one could categorize various types of vegetation and land use within an inland wetland using LANDSAT TM data. First, a Level 1/2 supervised classification was performed. Following a more detailed ground trust survey, a Level 3 classification was done. Aircraft L-band radar data were received and the decision was made to merge the TM and L-band data and assess whether vegetation catagories within the wetland areas could be better defined. Preliminary results indicate vegetation delineation is improved for open agricultural areas and water, but other features are more confused.

Description: The NASA/JPL Synthetic Aperture Radar (SAR) was flown over a 20 x 110 km test site in the Texas High Plains regions north of Lubbock during February/March 1984. The effect of incidence angle was investigated by comparing the pixel values of the calibrated and uncalibrated images. Ten-pixel-wide transects along the entire azimuth were averaged in each of the two scenes, and plotted against the calculated incidence angle of the center of each range increment. It is evident from the graphs that both the magnitudes and patterns exhibited by the corresponding transect means of the two images are highly dissimilar. For each of the cross-poles, the uncalibrated image displayed very distinct and systematic positive trends through the entire range of incidence angles. The two like-poles, however, exhibited relatively constant returns. In the calibrated image, the cross-poles exhibited a constant return, while the like-poles demonstrated a strong negative trend across the range of look-angles, as might be expected.

Description: Analysis of regional and high resolution remote sensing data coupled with detailed field investigations indicates Neogene compressional deformation in the southwest Dominican Republic. Airborne synthetic aperture radar data and high resolution near infrared photography show folds in Tertiary sediments and possible thrust fault scarps implying NE to SW compression in the region. Large road cuts through the scarps allow study of otherwise poorly accessible, heavily vegetated karst terrain. Deformation increases toward scrap fronts where small bedding-plane thrust faults become more numerous. Analysis of mesoscopic faults with slickensides indicates compression oriented between N to S and E to W. The lowermost scarp has highly sheared fault breccia and undeformed frontal talus breccias implying it is the basal thrust into which the higher thrust faults sole. Thus, the scarps probably formed in a regional NE to SW compressional stress regime and are the toes of thrust sheets. Previous workers have suggested that these scarps are ancient shorelines. However, the gross morphology of the scarps differs substantially from well known erosional terraces on the north coast.

Description: The problem of choosing an optimum scheme for the electrooptical analyzer of polarization and related control principles are discussed. An electrooptical deflector, which is advantageously used to employ a single photodetector and to remove systematic errors inherent in magnetographs with two photodetectors in the wings of the line is discussed, as well as adjustment errors of optical elements of the polarization analyzer and errors of control voltages. A method for measuring the telescope's polarization matrix, reduction of magnetographic measurements for instrumental polarization and calibration of magnetograph channels are examined. Questions of evaluating scattered light and of reducing magnetic field measurements are also considered as a computational procedure for the magnetic field vector parameters is briefly outlined. Computer control of the solar magnetograph and of the processing and control system software is discussed.

Description: A study was conducted to determine the suitability of the San Fernando Observatory's 61 cm (24 inch) aperture vacuum solar telescope and 3 m (118 inch) focal length vacuum spectroheliograph for Stokes Polarimetry measurements. The polarization characteristics of these two instruments was measured by determining their Mueller matrices as a function of telescope orientation, field angle, wavelength, grating type, and position of the measuring beam in the telescope entrance window. In general, the polarizing and depolarizing properties are small so that inversion of the system Mueller matrix will permit the accurate measurement of Stokes profiles for vector magnetic field determination. A proposed polarimeter design based on the use of a TV camera system to simultaneously scan six different polarization components of a given line profile is described. This design, which uses no rotating optics or electronic modulators and makes efficient use of the available irradiance, promises to yield high quality vector magnetograms.

Description: Airborne Imaging Spectrometer (AIS) data were collected 30 August 1985 from a desert shrub community in central Oregon. Spectra from artificial targets placed on the test site and from bare soil, big sagebrush (Artemesia tridentata wyomingensis), silver sagebrush (Artemesia cana bolander), and exposed volcanic rocks were studied. Spectral data from grating position 3 (tree mode) were selected from 25 ground positions for analysis by Principal Factor Analysis (PFA). In this grating position, as many as six factors were identified as significant in contributing to spectral structure. Channels 74 through 84 (tree mode) best characterized between-class differences. Other channels were identified as nondiscriminating and as associated with such errors as excessive atmospheric absorption and grating positin changes. The test site was relatively simple with the two species (A. tridentata and A. cana) representing nearly 95% of biomass and with only two mineral backgrounds, a montmorillonitic soil and volcanic rocks. If, as in this study, six factors of spectral structure can be extracted from a single grating position from data acquired over a simple vegetation community, then AIS data must be considered rich in information-gathering potential.

Description: Airborne Imaging Spectrometer (AIS) data were acquired over an area of freshwater wetlands in Central California on September 23, 1985. Plant samples were subsequently collected along the flight line with the goal of relating plant tissue chemistry to spectral reflectance in the near-infrared region. It was determined that a consistent relationship existed between spectral response and plant tissue chemistry. This was especially evident in the 1500 to 1700 nm region.

Description: Airborne Imaging Spectrometer (AIS) data were acquired in 1985 over the Bonanza Creek Experimental Forest, Alaska for the analysis of canopy characteristics including biochemistry. Concurrent with AIS overflights, foliage from fifteen coniferous and deciduous forest stands were analyzed for a variety of biochemical constituents including nitrogen, lignin, protein, and chlorophyll. Preliminary analysis of AIS spectra indicates that the wavelength region between 1450 to 1800 namometers (nm) displays distinct differences in spectral response for some of the forest stands. A flat field subtraction (forest stand spectra - flat field spectra) of the AIS spectra assisted in the interpretation of features of the spectra that are related to biology.

Description: Airborne Imaging Spectrometer (AIS) data were collected over the fossil hot spring deposit at Ivanhoe, Nevada in order to determine the surface distribution of NH4-bearing minerals. Laboratory studies show that NH4-bearing minerals have characteristic absorption features in the near-infrared (NIR). Ammonium-bearing feldspars and alunites were observed at the surface of Ivanhoe using a hand-held radiometer. However, first look analysis of the AIS images showed that the line was about 500 m east of its intended mark, and the vegetation cover was sufficiently dense to inhibit preliminary attempts at making relative reflectance images for detection of ammonium minerals.

Description: The Airborne Imaging Spectrometer (AIS) was flown over granitic, volcanic, and calc-silicate terrain around the Mary Kathleen Uranium Mine in Queensland, in a test of its mineralocial mapping capabilities. An analysis strategy and restoration and enhancement techniques were developed to process the 128 band AIS data. A preliminary analysis of one of three AIS flight lines shows that the data contains considerable spectral variation but that it is also contaminated by second-order leakage of radiation from the near-infrared region. This makes the recognition of expected spectral absorption shapes very difficult. The effect appears worst in terrains containing considerable vegetation. Techniques that try to predict this supplementary radiation coupled with the log residual analytical technique show that expected mineral absorption spectra can be derived. The techniques suggest that with additional refinement correction procedures, the Australian AIS data may be revised. Application of the log residual analysis method has proved very successful on the cuprite, Nevada data set, and for highlighting the alunite, linite, and SiOH mineralogy.

Description: The Singatse Range is composed of a series of 53 types of volcanic, plutonic, metamorphic, and sedimentary rocks. In addition the Jurassic plutonic rocks are also of economic interest for their copper mineralization which is contained in a porphyry dike swarm. The 1984 and 1985 flight results from the Airborne Imaging Spectrometer (AIS) instrument flown in the NASA/JPL C-130 aircraft are contrasted and compared. The 1984 data are less noisy than the 1985, in which many sets of vertical stripings from bad detectors can be seen. Significantly however, enough of the hydrothermal alteration patterns can be seen in each line at the mutual crossing points that one can say that the specific targets were detected in both year's flights. The spectra of both years are corrupted by the second-order effect from the grating, but 0-H bond absorption at essentially correct wavelengths for sericite and/or kaolinite can be seen.

Description: The surface mineralogy in and around Moses Rock diatreme, a kimberlite-bearing dike in SW Utah, was examined using internally calibrated Airborne Imaging Spectrometer (AIS) data. Distinct near-infrared absorption characteristics of clays, gypsum, and serpentine (a key marker for kinberlite concentration) allowed the surface units containing these components to be identified spatially and the relative abundance of each component measured. Within the dike itself, channels and dispersed components of kimberlite and blocks of country rocks were accurately determined.

Description: Analysis of Airborne Imaging Spectrometer (AIS) data acquired in Australia has revealed a number of operational problems. Horizontal striping in AIS imagery and spectral distortions due to order overlap were investigated. Horizontal striping, caused by grating position errors can be removed with little or no effect on spectral details. Order overlap remains a problem that seriously compromises identification of subtle mineral absorption features within AIS spectra. A spectrometric model of the AIS was developed to assist in identifying spurious spectral features, and will be used in efforts to restore the spectral integrity of the data.

Description: The Airborne Imaging Spectrometer (AIS) samples a region which is strongly influenced by decreasing solar irradiance at longer wavelengths and strong atmospheric absorptions. Four techniques, the Log Residual, the Least Upper Bound Residual, the Flat Field Correction and calibration using field reflectance measurements were investigated as a means for removing these two features. Of the four techniques field reflectance calibration proved to be superior in terms of noise and normalization. Of the other three techniques, the Log Residual was superior when applied to areas which did not contain one dominant cover type. In heavily vegetated areas, the Log Residual proved to be ineffective. After removing anomalously bright data values, the Least Upper Bound Residual proved to be almost as effective as the Log Residual in sparsely vegetated areas and much more effective in heavily vegetated areas. Of all the techniques, the Flat Field Correction was the noisest.

Description: The Voyager 1 and Voyager 2 narrow angle cameras have been imaging Uranus and Neptune (through several filters) from distances of several AU for the past four years. The justification for this is to determine the way in which the albedoes of the two planets vary with angle from the sun. The Voyager 1 spacecraft has already reached a phase angle of approx. 40 deg. for Neptune and approx. 70 deg. for Uranus. The albedo of a gaseous planet depends on the phase angle (angle from the sun through the planet to the observer), the color being observed, and the vertical distribution and nature of aerosols and clouds in the atmosphere of the planet. Since the colors are known and the phase angles, and phase curves will be used to constrain models of the aerosol and cloud structrures of Uranus and Neptune. A knowledge of the way albedo varies with phase angle allows one to compute the total amount of sunlight being absorbed by a planet. With knowledge of the solar flux incident on the planet and knowledge of how much infrared is being emitted by the planet (at least in the direction of the Earth and sun) one can determine a rough extimate of the internal heat source of the planet. Although Jupiter and Saturn have measured internal heat sources of magnitude comparable to their absorbed energy from the sun, preliminary results indicate that Uranus may not have an internal heat and that Neptune if it has one that heat source is small.

Description: Narrowband CCD profiles of C2 and grains in several comets (including P/Halley and P/Giacobini-Zinner) were performed. Rotational light curves were made of Comet P/Arend-Rigaux (visible and infrared) yielding the size, shape, albedo, and rotation period of the nucleus. Production rates were measured as a function of heliocentric distance for OH, CN, and C2 in P/Giacobini-Zinner and for OH, NH, CN, C3, and C2 in P/Halley. Detection and measurement was made of forbidden (O I) lines near 6300 and 5577 A in P/Halley, permitting the production rate of oxygen from CO to be distinguished from that from H2O. Identification of C-12C-13 lines in cometary spectra indicating a possible enrichment of C-13 over the telluric value was made. An assessment of techniques for detecting (determining the existence of) a trans-Neptunian comet belt is included.

Description: The Voyager data in a newly produced noise-reduced and recalibrated format has been received. New color spectrograms were developed on high resolution color terminals which display this data. The production of these new spectrograms utilizing the new format data is quite important, because it eliminates a serious problem of noise contamination and miscalibration in the old data set. In addition, a new Jovian plasma model was introduced, which includes the Io torus and accounts for 7 ionic species. The new plasma model is important in the ray tracing of hectometric (HOM) and kilometric (KOM) radiation which may be influenced by the Io torus.

Description: A multi-color, broad-band photographic program for monitoring atmospheric variability of Jupiter and Saturn with the 61-cm, f/75 telescope was continued. The archivial product consists of approximately 20 sequential images on 3 1/4 x 4 1/4 glass plates with a plate scale of 4.53 arc sec/mm. An eleven-step sensitometric wedge, recorded times of acquisition, and fiducial marks which determine the orientation of the plate, are recorded on each individual plate. This allows accurate positional measurements, as well as detailed relative surface brightness determinations. Detailed measurements of the Red Spot are being utilized in a study of zonal velocity variation and the ability to predict the longitude of the Red Spot during the Galileo mission. An ongoing 5-color series of Saturn has been maintained to map the seasonal changes in the belt-zone reflectivity. Digitization of a series of blue images containing the Red Spot and a series of red and blue images excluding the Red Spot are being processed and reduced to normalized surface brightness maps. This data is being utilized to map time-dependent brightness variations of selected features, belts, and ones.

Description: The interior structure of the Jovian planets was studied by means of observational data obtained by ground-based astronomy. Recent work was oriented toward a determination of oblateness from occultation measurements of the shape of planetary atmospheres. This provides a determination of the degree of central condensation of the planet, which is then compared with interior models and theoretical equations of state. As a serendipitous result of the attempts to measure the oblateness of Neptune, a partial Neptune ring (or arc) was discovered following an occultation observation on July 22, 1984. During 1985, older observations were reexamined to determine whether Neptune arcs had been detected (but not identified) during previous occultations. It appears that Neptunian arcs may locally imitate Uranian rings, with an 1981 event resembling Uranus' epsilon ring, while an 1984 event was more similar to the thinner Uranian rings such as the alpha ring.

Description: This program supports NASA's deep space exploration missions, particularly those to the outer Solar System, and also NASA's Earth-orbital astronomy missions, using ground-based observations, primarily with the NASA IRTF at Mauna Kea, Hawaii, and also with such instruments as the Kitt Peak 4 meter Mayall telescope and the NRAO VLA facility in Socorro, New Mexico. An important component of the program is the physical interpretation of the observations. There were two major scientific discoveries resulting from 8 micrometer observations of Jupiter. The first is that at that wavelength there are two spots, one near each magnetic pole, which are typically the brightest and therefore warmest places on the planet. The effect is clearly due to precipitating high energy magnetospheric particles. A second ground-based discovery is that in 1985, Jupiter exhibited low latitude (+ or - 18 deg.) stratospheric wave structure.

Description: The integrity of the metal-poly oxide and the gate oxide was evaluated for several 5-micron CMOS-bulk process. The pinhole array capacitor consists of diffused and poly fingers that form a network of MOS transistors (elements), which are capped by a deposited oxide and metal layer. The smallest structure used contained about 15,000 elements and the largest structure contained about 68,000 elements. Each structure was divided into several subarrays. The structures are placed a number of times on each wafer. From a yield analysis of the subarrays, the elements per defect were found to be typically in excess of 50,000 elements/defect for the metal-poly oxide and 100,000 elements/defect for the gate oxide. From the switching behavior of the transistors, the gate oxide defects were tentatively identified as gate-to-body shorts rather than gate-to-diffusion shorts.

Description: The purpose is to describe work that is being done to find theoretical models to describe radar backscatter from vegetation layers. The geometry of the problem is shown. The information that one would like to find through the application of the results of these models would include: the thickness of the layer; the absorption in the layer (i.e., density, moisture content, and biomass); the geometry of the scatterers (i.e., shape and orientation); how much of the received power is due to volume scattering only; and a way to enhance the ratio of scattering that has some interaction with the ground surface. The proposed ways to find this information are discussed.

Description: This study was conducted as a part of the research tasks under the Radar Land Cover Analysis Program. The Radar Land Cover Analysis objective is, through utilization of multisensor data, to gain a basic understanding of the measurements and data characteristics in the visible-IR-microwave regions of the electromagnetic spectrum associated with specific surface features and cover types. Since the results of analysis of data acquired by Shuttle Imaging Radar (SIR-A) and LANDSAT Thematic Mapper (TM) over the study area were reported (NSTL/ERL Report No. 228, December 1984), this study focused on the analysis and evaluation of the L-band multipolarization airborne SAR data acquired over a southeastern pine forest scene. The data acquisition mission was flown on September 8 and 9, 1983. The HH, HV polarizations and the VV, VH polarizations were used on the first and the second day, respectively. Due to instrumentation difficulties, the digital recorder recorded only the second day's data. Because of this, only the VV and VH polarization data were used in this analysis. However, the HH and HV polarization images were available for visual comparison. It appears that SAR digital numbers correlate with the index of green biomass.

Description: THEMIS was designed for accurate polarization measurements in order to determine the intensity and direction of the magnetic field without interference with the local variations of the thermodynamical parameters. That goal leads to the following requirements: (1) high spatial resolution in horizontal direction; (2) sufficient resolution in height, which requires observations in several spectral lines with a sufficient spectral resolution; (3) accurate polarization measurements; (4) adequate time coverage to follow the evolution of individual structures; (5) precise tracking and scanning mechanisms; and (6) sufficient field of view for the different observed structures. The design of the instrument is discussed in detail.

Description: A birefringent filter with a large field of view and no additional polarization is discussed. It plays an important role in observing the solar monochromatic image and the solar vector magnetic field. It has only one channel. For simultaneous multichannel observations, the solar spectrograph is better than the birefringent filter. A suggestion was proposed to try to obtain a multichannel birefringent filter which will be used in a new telescope at the Huairou reservoir station of Beijing Observatory. By means of N polarizing beam splitters, (N+1) channels can be divided. In principle, any number of limitless channels can be obtained, thereby subdividing the whole solar spectrum. But since the space in a telescope is limited, the channels to be used are also limited. For the new telescope, 5 and 9 channels are being considered, and the spectral range is from lambda 3800A to lambda 7000A. Many lines are included in this range, for example, H, K, H beta, lambda lambda 5324A, 5250A, 6302A, H alpha, etc., and some of the lines are suited to measure solar velocity fields. According to the character of these lines, the half width of each channel is determined. Moreover, in some channels the solid polarizing Michelson interferometer is considered for measuring velocity field with a lm/s accuracy. The advantages of the filter and problems to be solved are listed.

Description: The magnetograph was upgraded in both electronic control of the magnetograph hardware and in the polarization optics. The problems associated with the orignal polarimeter were: (1) field of view errors associated with the natural birefringence of the KD*P crystals; (2.) KD*P electrode failure due to the halfwave dc voltage required in one of the operational sequences; and (3) breakdown of the retardation properties of some KD*Ps when exposed to a zero to halfwave modulation (DC) scheme. The new polarimeter gives up the flexibility provided by two variable waveplates to adjust the retardances of the optics for a particular polarization measurement, but solves the problems associated with the original polarimeter. With the addition of the quartz quarterwave plates, a new optical alignment was developed to allow the remaining KD*P to correct for errors in the waveplates. The new optical alignment of the polarimeter is prescribed. The various sources of error, and how those errors are minimized so that the magnetograph can look at the transverse field in real time are discussed.

Description: A polarimeter was designed for high spatial and spectral resolution. It consists of a quarter-wave plate alternately operating in two positions for Stoke-V measurements and an additional quarter-wave plate for Stokes-U and -Q measurements. The spatial range covers 75 arcsec, the spectral window of about 1.8 a allows the simultaneous observations of neighboring lines. The block diagram of the data processing and acquisition system consists of five memories each one having a capacity of 10 to the 4th power 16-bit words. The total time to acquire profiles of Stokes parameters can be chosen by selecting the number of successive measurements added in the memories, each individual measurement corresponding to an integration time of 0.5 sec. Typical values range between 2 and 60 sec depending on the brightness of the structure, the amount of polarization and a compromise between desired signal-to-noise ratio and spatial resolution.

Description: Spectral characteristics of semi-arid shrub communities were examined using Airborne Imaging Spectrometer (AIS) data collected in the tree mode on 23 May 1985. Mesic sites with relatively high vegetation density and distinct zonation patterns exhibited greater spectral signature variations than sites with more xeric shrub communities. Spectral signature patterns were not directly related to vegetation density or physiognomy, although spatial maps derived from an 8-channel maximum likelihood classification were supported by photo-interpreted surface features. In AIS data, the principal detected effect of shrub vegetation on the alluvial fans is to lower reflectance across the spectrum. These results are similar to those reported during a period of minimal physiological activity in autumn, indicating that shadows cast by vegetation canopies are an important element of soil-vegetation interaction under conditions of relatively low canopy cover.

Description: Airborne Imaging Spectrometer (AIS) data were acquired for several vegetation types within the humid temperate eastern United States. The spectral region covered, 0.9 to 2.1 microns, was little used in vegetation studies. A preliminary analysis of spectral curves suggests that variations between vegetation spectra may be useful for discriminating plant communities. Calibration and normalization procedures must be refined to compensate for cloud cover, detector and other system noise, and possible second-order effects.

Description: Spectral reflectance properties of deciduous oak-hickory forests covering the eastern half of the Rolla Quadrangle were examined using Thematic Mapper (TM) data acquired in August and December, 1982 and Airborne Imaging Spectrometer (AIS) data acquired in August, 1985. For the TM data distinctly high relative reflectance values (greater than 0.3) in the near infrared (Band 4, 0.73 to 0.94 micrometers) correspond to regions characterized by xeric (dry) forests that overlie soils with low water retention capacities. These soils are derived primarily from rhyolites. More mesic forests characterized by lower TM band 4 relative reflectances are associated with soils of higher retention capacities derived predominately from non-cherty carbonates. The major factors affecting canopy reflectance appear to be the leaf area index (LAI) and leaf optical properties. The Suits canopy reflectance model predicts the relative reflectance values for the xeric canopies. The mesic canopy reflectance is less well matched and incorporation of canopy shadowing caused by the irregular nature of the mesic canopy may be necessary. Preliminary examination of high spectral resolution AIS data acquired in August of 1985 reveals no more information than found in the broad band TM data.

Description: Techniques using Munsell color transformations were developed for reducing 128 channels (or less) of Airborne Imaging Spectrometer (AIS) data to a single color-composite-image suitable for both visual interpretation and digital analysis. Using AIS data acquired in 1984 and 1985, limestone and dolomite roof pendants and sericite-illite and other clay minerals related to alteration were mapped in a quartz monzonite stock in the northern Grapevine Mountains of California and Nevada. Field studies and laboratory spectral measurements verify the mineralogical distributions mapped from the AIS data.

Description: Airborne Imaging Spectrometer (AIS) data, field and laboratory spectra and samples for X-ray diffraction analysis were collected in argillically altered Tertiary volcanic rocks in the Hot Creek Range, Nevada. From laboratory and field spectral measurements in the 2.0 to 2.4 micron range and using a spectroradiometer with a 4 nm sampling interval, the absorption band centers for kaolinite were loacted at 2.172 and 2.215 microns, for montmorillonite at 2.214 micron and for illite at 2.205. Based on these values and the criteria for resolution and separtion of spectral features, a spectral sampling interval of less than 4 nm is necessary to separate the clays. With an AIS spectral sampling interval of 9.3 nm, a spectral matching algorithm is more effective for separating kaolinite, montmorillonite, ad illite in Hot Creek Range than using the location of absorption minima alone.

Description: Airborne Imaging Spectrometer (AIS) data were collected over Virginia City, Nevada; an area of gold and silver mineralization with extensive surface exposures of altered volcanic rocks. The data were corrected for atmospheric effects by a flat-field method, and compared to library spectra of various alteration minerals using a spectral analysis program SPAM. Areas of strong clay alteration were identified on the AIS images that were mapped as kaolinitic, illitic, and sericitic alterations zones. Kaolinitic alteration is distinguishable in the 2.1 to 2.4 and 1.2 to 1.5 micrometer wavelength regions. Montmorillonite, illite, and sericite have absorption features similar to each other at 2.2 micrometer wavelength. Montnorillonite and illite also may be present in varying proportions within one Ground Instantaneous Field of View (GIFOV). In general AIS data is useful in identifying alteration zones that are associated with or lie above precious metal mineralization at Virginia City.

Description: Airborne Imaging Spectrometers (AIS) data collected in 1984 and 1985 showed pronounced striping in the vertical and horizontal directions. This striping reduced the signal to noise ratio so that features of the spectra of forest canopies were obscured or altered by noise. This noise was removed by application of a notch filter to the Fourier transform of the imagery in each waveband.

Description: Selective absorption of electromagnetic radiation by atmospheric gases and water vapor is an accepted fact in terrestrial remote sensing. Until recently, only a general knowledge of atmospheric effects was required for analysis of remote sensing data; however, with the advent of high spectral resolution imaging devices, detailed knowledge of atmospheric absorption bands has become increasingly important for accurate analysis. Detailed study of high spectral resolution aircraft data at the U.S. Geological Survey has disclosed narrow absorption features centered at approximately 2.17 and 2.20 micrometers not caused by surface mineralogy. Published atmospheric transmission spectra and atmospheric spectra derived using the LOWTRAN-5 computer model indicate that these absorption features are probably water vapor. Spectral modeling indicates that the effects of atmospheric absorption in this region are most pronounced in spectrally flat materials with only weak absorption bands. Without correction and detailed knowledge of the atmospheric effects, accurate mapping of surface mineralogy (particularly at low mineral concentrations) is not possible.

Description: Several laboratory calibration tests were developed for the Airborne Imaging Spectrometer (AIS). The goals of these tests are to adjust the physical alignment of the detector within the optical system and set the spectral endpoints, and produce a calibration file of multipliers which equalizes the relative responses of each of the detector elements in the entire two-dimensional array. Tests are also performed as part of an ongoing effort to provide absolute radiometric calibration. The tests are described and the merits and limitations of each are discussed.

Description: The research effort was concentrated toward comet P/Halley, although observations of other comets including Giacobini-Zinner, Hartley-Good and Thiele were made as opportunities arise. In preparing for the apparition of P/Halley, detailed predictions for the emission in the 18 cm OH transitions were made in order to assist observers and to indicate what type of data would be particularly valuable. Likewise, since occultations by the comet of background radio sources can provide unique types of information, the tracks of P/Halley and P/Giacobini-Zinner were surveyed with the NRAO Very Large Array, background sources were mapped, and a catalogue of occulted sources published. Beginning in September, 1985, regular observations of the 18 cm OH lines have been made for P/Halley using the 43 m antenna of the NRAO in Greenbank, West Virginia. These data promise to provide the most accurate time sequence for the OH emission for any comet ever obtained at radio wavelengths. From the linewidth and shape, information is obtained on the kinetics of the gas in the cometary coma. An extensive series of observations have been undertaken with 14 m antenna to study emission from the HCN molecule in P/Halley. These data provide the first definitive detection of this component of the cometary ices. Interesting variations in the production of HCN were observed with time scales less than a day. Likewise, there appeared to be variations in the ratio of the hyperfine components of the J = 1-0 transition.

Description: The first field test of NASA's Global Positioning System (GPS) Geodetic Program took place in March of 1985. The principal objective of this test was the demonstration of the feasibility of the fiducial station approach to precise GPS-based geodesy and orbit determination. Other objectives included an assessment of the performance of the several GPS receiver types involved in these field tests and the testing of the GIPSY software for GPS data analysis. In this article, the GIPSY (GPS Inferred Positioning System) software system is described and baseline solutions are examined for consistency with independent measurements made using very long baseline interferometry.

Description: With the advent of frequent Space Transportation System Shuttle missions, photography from hyperaltitudes stands to become an accessible and convenient resource for scientists and environmental managers. As satellite products (such as LANDSAT) continue to spiral in costs, all but the most affluent consumer is finding Earth imagery from space to be more and more unavailable. Therefore, the potential for Shuttle photography to serve a wide variety of users is increasing. However, despite the popularity of photos from space as public relations tools and report illustrations, little work has been performed to prove their scientific worth beyond that as basic mapping bases. It is the hypothesis of this project that hand-held Earth photography from the Space Shuttle has potentially high scientific merit and that primary data can be extracted. In effect, Shuttle photography should be considered a major remote sensing information resource.

Description: Work completed on Apollo 14 basalts has been published. The two dates obtained from these rocks comprised the oldest and two of the three oldest ages (4.1 and 4.3 billion years) known for lunar maria basalts; thus their ages are important in understanding the moon's earliest history. Owing to the antiquity of these rocks, two more fragments have been dated as part of a second ASEE/NASA SFF program. The new ages are 3.95 and 4.12 billion years, thus further establishing and amplifying the earlier results. This work, although perhaps more interesting for its chronologic information, was begun as a test of chemical and petrographic models. Fragments of Apollo basalt were placed into five categories, based on petrologic and chemical, especially rare-earth element, composition. Isotopic studies were begun in an attempt to determine if the five groups of basalts were related by age or initial isotopic composition (isotopic composition of lava at time of extrusion). Although a few of the representatives of the five groups have the same age and/or initial strontium-isotopic composition, within the analtytical uncertainties, most apparently are unrelated. Petrologic implications of these data will be published in an appropriate journal.

Description: One aspect of the study of Titan's atmosphere is the elucidation of the chemical and physical nature of the aerosols. In order to facilitate this, a program to produce laboratory synthesized model materials for Titan's aerosol and to study their chemical and physical properties is now in progress. Various processes, including electric discharge, photolysis by ultraviolet light, and irradiation by energetic particles, will be used to produce the materials. A first set of experiments where a nominal Titan mixture (97%N2, 3% CH4, 0.2% H2) was subjected to pulsed high temperature shocks yielded a reddish brown waxy solid. This material was subjected to pyrolysis/gas chromatography, a technique that has been proposed as a method for analysis of the Titan aerosols. Preliminary results show the material to consist of simple hydrocarbons but little else, at least up to temperatures of 600 C. Since the material was colored, compounds other than those mentioned above must be present.

Description: The production of high-resolution topographic maps derived from interferometric synthetic aperture radar observations of the Earth is reported. Topographic maps are typically determined from stereo-pair optical photographs. Vertical relief causes the same terrain to appear in a slightly different projection for differing look angles, and this shift in appearance is interpreted in terms of the height of the terrain. The radar interferometric approach is related to the stereo technique in that the terrain is viewed at two different angles; however, in this case, the angular separation of the antennas is extremely small, on the order of a milliradian or less, as compared to tens of degrees for the optical case. Thus, the geometrical distortion and subsequent rectification correction algorithms are much less severe in the reduction of interferometric data.

Description: Several enhancements were recently made to the Haleakala polarimeter. Linear array detectors provide simultaneous resolution over a 3-A wavelength range, with spectral resolution of 40 mA. Optical fibers are now used to carry the intensity-modulated light from the rotating quarter-wave plate polarimeter to the echelle spectrometer, permitting its removal from the spar to a more stable environment. These changes, together with improved quarter-wave plates, reduced systematic errors to a few parts in 10,000 for routine observations. Examples of Stokes profiles and derived magnetic field maps are presented.

Description: The Solar Birefringent Filter (Filter Polarisiant Solaire Selectif FPSS) of Meudon Observatory is presently located at the focus of a solar refractor with a 28 cm lens directly pointed at the Sun. It produces a diffraction limited image without instrumental polarization and with a spectral resolution of 46,000 in a field of 6 arc min. diameter. The instrument is calibrated for absolute Doppler velocity measurements and is presently used for quantitative imagery of the radial velocity motions in the photosphere. The short period oscillations are recorded. Work of adapting the instrument for the imagery of the solar surface in the Stokes parameters is discussed. The first polarizer of the birefringent filter, with a reference position angle 0 deg, is associated with a fixed quarter wave plate at +45 deg. A rotating quarter wave plate is set at 0 deg and can be turned by incremented steps of exactly +45 deg. Another quarter wave plate also initially set at 0 deg is simultaneously incremented by -45 deg but only on each even step of the first plate. A complete cycle of increments produces images for each of the 6 parameters I + or - Q, I + or - U and I + or - V. These images are then subtracted by pairs to produce a full image in the three Stokes parameters Q, U and V. With proper retardation tolerance and positioning accuracy of the quarter wave plates, the cross talk between the Stokes parameters was calculated and checked to be minimal.

Description: Microgravity offers a unique environment for studying polymer diffusion and polymer polymerization reactions. The absence of convection currents, which are the major mode of mixing at the molecular level on Earth, are eliminated or reduced in the microgravity environment. More importantly, the prediction of unique copolymer composition development in microgravity allows controlled formation of new compositions of matter. The absence of mixing at the molecular level should produce unique short block copolymers available for the first time for comonomer compositions which normally lead to random or long block copolymer under good mixing. The investigation of fundamental polymer diffusion and polymer polymerization processes in microgravity is proposed. This effort will involve fundamental studies of monomer and polymer diffusion; their effects on initiation, propagation, and especially termination kinetics rate constant; and the accurate evaluation of copolymerization reactivity ratios in microgravity. The experimental design is presented for these studies along with an evaluation technique for in situ monitoring of polymer diffusion and polymerization kinetics.

Description: The analysis of light scattered from an ensemble of particles has long been a preferred method for characterizing their physical properties. Instrumentation to perform the measurements which forms the basis for such analysis is available in many forms based upon a variety of different experimental techniques. A system is presented which is singularly applicable for making many types of measurements in a microgravity environment. The commercial version of this device, the DAWN-F, has been used in many labs throughout the world to perform analyses of particular importance for both research and production. Light scattering theory is reviewed and the structure and function of the system is described.

Description: Avalanche photodiodes (APD) are excellent small area, solid state detectors for photon counting. Performance possibilities include: photon detection efficiency in excess of 50 percent; wavelength response from 400 to 1000 nm; count rate to 10 (exp 7) counts per sec; afterpulsing at negligible levels; timing resolution better than 1 ns. Unfortunately, these performance levels are not simultaneously available in a single detector amplifier configuration. By considering theoretical performance predictions and previous and new measurements of APD performance, the anticipated performance of a range of proposed APD-based photon counting modules is derived.

Description: Traditional optical systems for photon correlation spectroscopy and laser anemometry have relied upon physically large and fairly expensive lasers, bulk-optics such as lenses of a few inches diameter, large mechanical mounts and carefully selected, fragile and bulky photon counting photomultiplier detectors. In some cases, experimental fluid dynamics at a desired position in a flow, perhaps deep inside complex machinery, is physically impossible or very difficult. Similar problems exist with photon correlation spectroscopy, e.g., remote and heterodyne experiments. Various optical and electro optical components were investigated and characterized with the aim of replacing existing photon correlation laser spectroscopy and anemometry techniques in miniaturized form, and with significant cost reduction. Very recently, a range of miniature, modular light scattering systems were constructed from little solid state optical and electro optical components, and experimentally verified measurement performance comparable to standard lab photon correlation spectroscopy and laser anemometry equipment.

Description: The establishment of lunar bases is the next logical step in the exploration of space. Permanent lunar bases will support scientific investigation, the industrialization of space, and the development of self-sufficiency on the Moon. Scientific investigation and research and development would lead to applications utilizing lunar material resources. By utilizing these resources, the industrialization of space can become a reality. The above two factors coupled with the development of key and enabling technologies would lead to achievement of self-sufficiency of the lunar base. Attention was focused on specific design(s) to be pursued during subsequent stages in advanced courses. Some of the objectives in the project included: (1) minimizing the transportation of construction material and fuel from earth, or maximizing the use of the lunar material; (2) use of novel materials and light weight structures; (3) use of new manufacturing methods and technology such as magnetically levitated, or superconducting materials; and (4) innovative concepts of effectively utilizing the exotic lunar conditions, i.e. high thermal gradients, lack of atmosphere, zero wind forces, and lower gravity, etc.

Description: The Multispectral Atmospheric Mapping Sensor (MAMS) is an airborne scanner which collects imagery in eight visible and three IR bands, with ground resolution of 100 m at a nominal aircraft altitude of 20 km. The visible channels provide continuous spectral coverage from 0.42 to 1.05 microns, and the IR channels measure upwelling and reflected radiation at combinations of 3.7, 6.5, 11.1, and 12.5 microns. These include channels nearly identical to the Landsat TM channels 1-4, and similar to those on the VISSR Atmospheric Sounder (VAS) and AVHRR instruments. The high spatial resolution permits investigation of surface thermal and atmospheric water vapor structure at scales not available from current stabilities. Significant modifications have been made since engineering flights in 1985 to improve the radiometric performance. The increased data quality and recent multidisciplinary applications of this data are presented.

Description: In summer 1988 an intensive field experiment was conducted in the vicinity of the Pisgah lava flow in the Mojave Desert. Physical properties such as microtopography, composition, soil moisture, and dielectric constant were measured at five sites representing surfaces with rms heights varying from less than one centimeter to tens of centimeters. In addition, polarimetric radar images at P-band, L-band, and C-band were acquired at three different incidence angles with the NASA/JPL airborne imaging radar polarimeter. Using trihedral corner reflectors deployed in the area prior to imaging, the L- and C-band images were calibrated to provide sigma0 values for each resolution element in the scene. The results of inferring geophysical parameters such as rms surface height and correlation length of the measured surfaces by fitting the observed signatures with those predicted by the small-perturbation model are presented: for smoother surfaces, the rms height values inferred are in good agreement with in situ measurements.

Description: Images from an airborne, scanning radiometer operating at a frequency of 98 GHz have been analyzed. The millimeter-wave images were obtained in 1985-1986 using the JPL millimeter-wave imaging sensor. The goal of this study was to enhance the information content of these images and make their interpretation easier. A visual-interpretative approach was used for information extraction from the images. This included application of nonlinear transform techniques for noise reduction and for color, contrast, and edge enhancement. Results of using the techniques on selected millimeter-wave images are discussed.

Description: Radar modeling of mangal forest stands in the Sundarbans area of southern Bangladesh is discussed. The modeling uses radar system parameters with forest data on tree height, spacing, biomass, species combinations, and water content (including slightly conductive water) in leaves and trunks of the mangal. For Sundri and Gewa tropical mangal forests, six model components are proposed; the models are required to explain the contributions of various combinations of forest species in the attenuation and scattering of mangal-vegetated nonflooded or flooded surfaces. Statistical data of simulated images have been compared with those of SIR-B images both to refine the modeling procedures and to characterize the model output appropriately. The possibility of delineation of flooded or nonflooded boundaries is discussed.

Description: Surface-air temperature differences are commonly used in a bulk resistance equation for estimating sensible heat flux (H), which is inserted in the one-dimensional energy balance equation to solve for the latent heat flux (LE) as a residual. Serious discrepancies between estimated and measured LE have been observed for partial-canopy-cover conditions, which are mainly attributed to inappropriate estimates of H. To improve the estimates of H over sparse canopies, one- and two-layer resistance models that account for some of the factors causing poor agreement are developed. The utility of the two models is tested with remotely sensed and micrometeorological data for a furrowed cotton field with 20 percent cover and a dry soil surface. It is found that the one-layer model performs better than the two-layer model when a theoretical bluff-body correction for heat transfer is used instead of an empirical adjustment; otherwise, the two-layer model is better.

Description: Experimental treatments in a Douglas-fir forest in NE New Mexico were carried out to determine whether differences in forest canopy chemistry could be detected using data from the Airborne Imaging Spectrometer (AIS-2). Experimental treatments consisted of nitrogen fertilizer additions, sawdust additions, and control plots. After AIS-2 data were collected, the digital number of a given pixel was extracted from each channel, yielding 128 values that were used to form a spectrum. Four spectra were extracted from each treatment plot. Multiple stepwise linear regressions between first and second difference transformations of AIS-2 spectra and the canopy characteristics of biomass, nitrogen concentration, and nitrogen content were performed. The results showed a coefficient of multiple determination of 0.71 between first-difference AIS-2 spectra and measured nitrogen concentration in foliage, indicating that it may be possible to predict nitrogen concentration in Douglas fir using AIS-2 spectra.