ISSN:
0947-5117
Keywords:
Chemistry
;
Polymer and Materials Science
Source:
Wiley InterScience Backfile Collection 1832-2000
Topics:
Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics
Description / Table of Contents:
Investigation of the effect of galvanic corrosion between steel in concrete and steel in soilThe investigation of cathodic polarization of steel in concrete on samples of portland cement and blast furnace cement revealed that oxygen reduction on steel in portland cement is less hindered than on steel in blast furnace cement. As to the magnitude of the cathodic current the aeration of the samples is important. Dry stored samples before measuring case a higher current density than wet stored ones. A significant relationship of the cathodic current depending on the water/cement value and the storage time of concrete could not be ascertained. The polarization resistances for portland cement samples lie within 86 and 3000 kΩ · cm2 and for blast furnace cement samples between 430 and 5100 kΩ · cm2.The measurements of the anodic current densities on corrosion cells of steel in concrete/steel in solution and steel in wet sand respectively rendered, by varying the cathode/anode aspect ratio from 1000: 1 to 1: 1, values for portland cement samples between 560 and 1,2 μAJcm2 (corresponding to an annual corrosion of 6,5 and 0,014 mm respectively), and for blast furnace cement samples values between 730 and 0,28 μA/cm2 (corresponding to an annual corrosion rate of 8,5 and 0,003 mm respectively). A decrease of the anodic current density variable with time could not be observed during the 28 days of measurements.On account of the investigations the following conclusions can be made:A formation of a corrosion cell with steel in concrete/steel in soil is particularly then to be expected if the concrete is dry on one side, e.g. the foundation of a building where oxygen diffuses by way of the gas pores in the concrete from the inner side to the cathode. This is less serious if the concrete is fully embedded in soil and thoroughly moistened. In this case the transport of oxygen has to be carried via waterfilled pores.
Notes:
Die Untersuchung der kathodischen Polarisation von Stahl in Beton an Proben aus Portland- und Hochofenzement ergab, daß die Sauerstoffreduktion an Stahl in Portlandzement weniger gehemmt ist als an Stahl in Hochofenzement. für die Größe der kathodischen Ströme ist die Belüftung des Betons wichtig. Trocken vorgelagerte Proben liefern höhere Stromdichten als naß vorgelagerte. Eine deutliche Abhängigkeit der kathodischen Stromdichte vom Wasser/Zement-Wert und von der Auslagerungszeit des Betons konnte nicht festgestellt werden. Die Potarisationswiderstände liegen für Portlandzementproben zwischen 86 und 3000 kΩ · cm2, für Hochofenzementproben zwischen 430 und 5100 kΩ · cm2.Die Messung der anodischen Stromdichte an Korrosionselementen Stahl in Beton/Stahl in Lösung bzw. feuchtem Sand lieferte bei Variation des Flächenverhältnisses Kathode/Anode von 1000: 1 bis 1: 1 für Portlandzement-Proben. Werte zwischen 560 und 1,2 μA/cm2 (entsprechend einer Abtragungsrate von 6,5 bzw. 0,014 mm/a), für Hochofenzementproben zwischen 730 and 0,28 μA/cm2 (entsprechend einer Abtragungsrate von 8,5 bzw. 0,003 mm/a). Ein zeitlicher Abfall der Anodenstromdichte bei Messungen über 28 Tage konnte nicht beobachtet werden.Aufgrund der Untersuchungen lassen sich folgende Schlußfolgerungen ziehen:Eine Elementbildung Stahl in Beton/Stahl im Erdboden ist besonders dann zu erwarten, wenn der Beton von einer Seite trocken ist, z. B. das Fundament eines Gebäudes, in welchem von der Innenseite der Sauerstoff über die Gasporen im Beton zur Kathode diffundiert. Sie ist weniger gravierend, wenn der Beton voll im Erdboden eingebettet und durchfeuchtet ist. In diesem Fall muß der Sauerstofftransport über die mit Wasser gefüllten Poren im Beton erfolgen.
Additional Material:
5 Ill.
Type of Medium:
Electronic Resource
URL:
http://dx.doi.org/10.1002/maco.19820330204
Permalink