ALBERT

Description: The Single-Mode Projection Filter (SPF) is a newly developed algorithm for eigensystem parameter identification from both analytical results and test data. The SPF is formulated with a single mode only and practical for parallel processing implementation. Explicit formulations of SPF are derived for the multi-input multi-output (MIMO) system by using the orthogonal matrices of the controllability and observability matrices in the general sense. The modal parameters of SPF are initially obtained from an analytical model in modal space. The experimental data are then processed through SPF to update its modal parameters and to minimize a cost function defined by the norm of an error matrix. The updated modal parameters represent the characteristics of the test data. A two-dimensional global minimum optimization algorithm is developed and applied for the filter update by using the interval analysis method. The SPF is developed based on a single-mode subsystem and identifies only one modal frequency and one modal damping within a specified region. For an n-modes structure, n SPF can be implemented for parallel processing to reduce the computational burden. The SPF is applied to analyze the simulated data for the MAST beam structure. The estimated modal parameters are comparable to those from the Eigensystem Realization Algorithm (ERA) and repeated modal frequencies are identified. The modal analysis of the Spacecraft Control Laboratory Experiment (SCOLE) data is also performed by using the ERA and the Maximum Likelihood Estimate (MLE). The result shows that the first five modal frequencies are very close from ERA and MLE. However, there are slight disparities in the damping rates and the computational burdens are quite different among these two algorithms.

Description: The direct interaction approximation is used to treat turbulence in a compressible medium with constant mean gradients. The set of coupled nonlinear integrodifferential equations is derived that is satisfied by the transverse and longitudinal energy spectral functions, Q(T) and Q(L) and by the transverse and longitudinal response functions, G(T) and G(L). Finally, expressions for the average of the product of pairs of physically relevant fluctuating quantities (velocity, temperature, density) are derived in terms of Q(T) and Q(L).

Description: The conditions under which finite difference schemes for the shallow water equations can conserve both total energy and potential enstrophy are considered. A method of deriving such schemes using operator formalism is developed. Several such schemes are derived for the A-, B- and C-grids. The derived schemes include second-order schemes and pseudo-fourth-order schemes. The simplest B-grid pseudo-fourth-order schemes are presented.

Description: Renormalization-group theory is applied to incompressible three-dimensional Navier-Stokes turbulence so as to eliminate unresolvable small scales. The renormalized Navier-Stokes equation now includes a triple nonlinearity with the eddy viscosity exhibiting a mild cusp behavior, in qualitative agreement with the test-field model results of Kraichnan. For the cusp behavior to arise, not only is the triple nonlinearity necessary but the effects of pressure must be incorporated in the triple term. The renormalized eddy viscosity will not exhibit a cusp behavior if it is assumed that a spectral gap exists between the large and small scales.

Description: The physical mechanism governing the centring of a hollow liquid shell in capillary oscillations, which has been observed in experiments, is investigated theoretically. First, the shell is assumed to be inviscid and to have a thickness that is much less than its spherical radius. A system of one-dimensional nonlinear equations of motion is derived using a thin-sheet model. From a numerical study the nonlinear effects of the wave are found to cause the core to oscillate slowly relative to the shell while the centre of mass of the whole system remains stationary. The effects of small viscosity are then considered in an approximation. Finally the strength of the centring mechanism is compared with that of the decentring effect due to buoyancy. The findings are consistent with the limited experimental information available.

Description: Developing fluid flow in a curved duct of square cross-section is studied numerically by a factored ADI finite-difference method on a staggered grid. A central-difference scheme with primitive variables is used inside the computational domain to reduce numerical diffusion. Two Reynolds numbers, 574 and 790, based upon a bulk velocity and hydraulic diameter are chosen for curvature ratios of 1/6.45 and 1/2.3, respectively. It is found that the secondary flow is far more complicated than expected, with the appearance of at least two pairs of vortices. Main-flow separation is also observed for the higher curvature ratio. Furthermore, it is observed that the flow develops into two quite different states downstream, depending upon the inlet conditions. Solutions of the fully developed Navier-Stokes equations is shown to be not unique beyond a certain critical Reynolds number. Developing flow seems to evolve into the fully developed state along a particular branch into which the fully developed solution bifurcates.

Description: A development history and current status evaluation are presented for the theory of permeability and percolation. The microscale phenomena treated in this field have proven difficult to analyze due both to their tortuous geometry and the influence of capilarity. Capilary effects may be not only important but predominant, and are differentiated into those at the fluid-fluid interface, and those involving the existence of a contact line between the solid substrate and this interface. Percolation theory has been borrowed from physics and adapted to the two-phase engineering context.

Description: The morphological stability of a rotating and solidifying disk is investigated under the assumption that delta, the thickness of the viscous boundary layer, is much larger than delta(c), the thickness of the solute boundary layer. It is found that axisymmetric disturbances with wavelengths comparable to delta respond to nonparallel flow effects and have stability characteristics quite different from disturbances in a parallel flow. These long waves are unstable because of the nonparallel flow and would decay without it. This analysis thus identifies a new mechanism of morphological change induced by flow.

Description: In this paper, the receptivity of a typical free shear layer to pulse-type and periodic excitation is studied. This is done by solving the initial-value problem completely and studing its long-time behavior. This leads to a wave packet for the pulse. By the superposition of many wave packets, a spatial instability mode when the flow is convectively unstable is generated. This establishes a general and simple relationship between the receptivities for pulse-type and sinusoidal excitations. It is found that a shear layer is very receptive to high-frequency disturbances that are generated near the centerline of the layer.

Description: The turbulent boundary layer on a flat plate, with zero pressure gradient, is simulated numerically at four stations between R sub theta = 225 and R sub theta = 1410. The three-dimensional time-dependent Navier-Stokes equations are solved using a spectral method with up to about 10 to the 7th grid points. Periodic spanwise and streamwise conditions are applied, and a multiple-scale procedure is applied to approximate the slow streamwise growth of the boundary layer. The flow is studied, primarily, from a statistical point of view. The solutions are compared with experimental results. The scaling of the mean and turbulent quantities with Reynolds number is compared with accepted laws, and the significant deviations are documented. The turbulence at the highest Reynolds number is studied in detail. The spectra are compared with various theoretical models. Reynolds-stress budget data are provided for turbulence-model testing.

Description: A method is proposed for treating steady-state, thermally driven convection using the full direct interaction approximation to treat the nonlinear energy transfer and a prescribed instability function to model the eenrgy input. The instability function used is the growth rate of the mechanism generating the turbulence. This methodology can be easily generalized and applied to other driving mechanisms. The 1/3 power law form of the N vs. R relation for water is duplicated here and the coefficient is computed, using a two-point closure, to be less than about 0.08.

Description: p/n InP homojunction solar cells with a modified contacting scheme have been fabricated from wafers grown by liquid phase epitaxy. A p(+)-In(0.53)Ga(0.47)As contacting layer is incorporated in the cell structure to reduce contact resistance and to eliminaate surface spiking problems at the front surface. The highest conversion efficiency (total area) obtained under AM0 illumination is 15.0 percent. The corresponding open-circuit voltage, short-circuit current density, and fill factor for the best cell are 0.866 V, 29.3 mA/sq cm, and 81.0 percent, respectively.

Description: Evidence is that tunneling via states in the forbidden gap is the dominant source of excess current in the dark current-voltage (I-V) characteristics of high-efficiency DMCVD grown Al(x)Ga(1-x)As/GaAs(x is equal to or greater than 0.85) solar cells. The dark forward and reverse I-V measurements were made on several solar cells, for the first time, at temperatures between 193 and 301 K. Low-voltage reverse-bias I-V data of a number of cells give a thermal activation energy for excess current of 0.026 + or - 0.005 eV, which corresponds to the carbon impurity in GaAs. However, other energy levels between 0.02 eV and 0.04 eV were observed in some cells which may correspond to impurity levels introduced by Cu, Si, Ge, or Cd. The forward-bias excess current is mainly due to carrier tunneling between localized levels created in the space-charge layer by impurities such as carbon, which are incorporated during the solar cell growth process. A model is suggested to explain the results.

Description: Second-order effects in metal-oxide-semiconductor field-effect transistors (MOSFETs) are important for devices with dimensions of 2 microns or less. The short and narrow channel effects and drain-induced barrier lowering primarily affect threshold voltage, but formulas for drain current must also take these effects into account. In addition, the drain current is sensitive to channel length modulation due to pinch-off or velocity saturation and is diminished by electron mobility degradation due to normal and lateral electric fields in the channel. A model of a MOSFET including these considerations and emphasizing charge conservation is discussed.

Description: A feed network comprised of a combination of coplanar waveguide and slot transmission line is described for use in an array module of four microstrip elements. Examples of the module incorporating such networks are presented as well as experimentally obtained impedance and radiation characteristics.

Description: The relationship between the spectra of the three normal stresses near a turbulent shear layer is derived from the constraint of irrotationality. The relationship implies that the common practice of determining time scales of the turbulence from spectra in the near field is not valid. This implication is reinforced by a discussion of the scaling of irrotational spectra that follows from the formulation of Phillips (1975).

Description: The structure of the vorticity field in the viscous wall layer of a turbulent channel is studied by examining the results of a fully resolved direct numerical simulation. It is shown that this region is dominated by intense three-dimensional shear layers in which the dominant vorticity component is spanwise. The advection and reproduction processes of these structures are examined and shown to be consistent with the classical generation mechanism for two-dimensional Tollmien-Schlichting waves. This process is fundamentally different from the usually accepted mechanism involving hairpin vortices.

Description: An algebraic stress turbulence model and a computational procedure for turbulent boundary layer flows which is based on the semidiscrete Galerkin FEM are discussed. In the algebraic stress turbulence model, the eddy viscosity expression is obtained from the Reynolds stress turbulence model, and the turbulent kinetic energy dissipation rate equation is improved by including a production range time scale. Good agreement with experimental data is found for the examples of a fully developed channel flow, a fully developed pipe flow, a flat plate boundary layer flow, a plane jet exhausting into a moving stream, a circular jet exhausting into a moving stream, and a wall jet flow.

Description: Samples of epitaxial GaAs grown on (100) Si substrates using molecular beam epitaxy were annealed at four different temperatures, from 800 to 950 C. Following annealing, the samples were analyzed using secondary ion mass spectrometry. Depth profiles of Ga, As, and Si reveal optimum conditions for annealing, and place a lower limit on a damage threshold for GaAs/Si substrates.

Description: Free-streamline theory is used to analyze the deformation and dislodging by wind pressure of drops of liquid adhered by surface tension to a solid surface. The critical Weber number for droplets to be dislodged is determined as a function of advancing and receding contact angle. Graphical results for drop shape are in good agreement with observation.

Description: A new class of cascade high-efficiency photovoltaics designed for space-based applications is proposed. The design improves upper subcell performance and avoids electrical and optical losses associated with an intercell ohmic contact. Multijunction upper subcells reduce bulk recombination of photogenerated minority carriers by decreasing the average collection distance, yielding improved spectral response and radiation tolerance. A three-terminal design is employed which circumvents the need for a monolithic intercell contact and, thus, the losses associated with such a contact. Problems related to array interconnection of three-terminal devices may be solved by creating a two-terminal cell from complementary pairs (n-p-n and p-n-p) of three-terminal cells. Simulations of lattice-matched AlGaAs-GaAs and lattice-mismatched AlGaAs-InGaAs cascade cells show that one-sun AM0 efficiencies in excess of 26 and 28 percent, respectively, are possible.

Description: A class of codes called finite-state (FS) codes is defined and investigated. The codes, which generalize both block and convolutional codes, are defined by their encoders, which are finite-state machines with parallel inputs and outputs. A family of upper bounds on the free distance of a given FS code is derived. A general construction for FS codes is given, and it is shown that in many cases the FS codes constructed in this way have a free distance that is the largest possible. Catastrophic error propagation (CEP) for FS codes is also discussed. It is found that to avoid CEP one must solve the graph-theoretic problem of finding a uniquely decodable edge labeling of the state diagram.

Description: In order to provide watt-level CW output power throughout the millimeter and submillimeter wave region, thousands of solid-state diodes have been monolithically integrated using a metal grid to produce a highly efficient frequency multiplier. Devices considered include GaAs Schottky diodes, thin MOS diodes, and GaAs Barrier-Intrinsic-N(+)diodes. The performance of the present compact low-cost device has been theoretically and experimentally validated.

Description: A 256K DRAM has been used to study the lateral transport of charge (electron-hole pairs) induced by direct ionization from heavy-ion tracks in an IC. The qualitative charge transport has been simulated using a two-dimensional numerical code in cylindrical coordinates. The experimental bit-map data clearly show the manifestation of lateral charge transport in the creation of adjacent multiple-bit errors from a single heavy-ion track. The heavy-ion data further demonstrate the occurrence of multiple-bit errors from single ion tracks with sufficient stopping power. The qualitative numerical simulation results suggest that electric-field-funnel-aided (drift) collection accounts for single error generated by an ion passing through a charge-collecting junction, while multiple errors from a single ion track are due to lateral diffusion of ion-generated charge.

Description: An extensive analytical and experimental study SEU in an advanced silicon bipolar process was made. The modeling used process and device parameters to model the SEU charge, collection, and circuit response derived from a special version of PISCES in cylindrical coordinates and SPICE, respectively. Data are reported for test cells of various sizes.

Description: An addressable matrix of 16 n- and 16 p-MOSFETs was designed to extract the dc MOSFET parameters for all dc gate bias conditions before and after irradiation. The matrix contains four sets of MOSFETs, each with four different geometries that can be biased independently. Thus the worst-case bias scenarios can be determined. The MOSFET matrix was fabricated at a silicon foundry using a radiation-soft CMOS p-well LOCOS process. Co-60 irradiation results for the n-MOSFETs showed a threshold-voltage shift of -3 mV/krad(Si), whereas the p-MOSFETs showed a shift of 21 mV/krad(Si). The worst-case threshold-voltage shift occurred for the n-MOSFETs, with a gate bias of 5 V during the anneal. For the p-MOSFETs, biasing did not affect the shift in the threshold voltage. A parasitic MOSFET dominated the leakage of the n-MOSFET biased with 5 V on the gate during irradiation. Co-60 test results for other parameters are also presented.

Description: Experimental measurements are reported of the degradation effects of high-energy particles (heavy Br ions and electrons) and Co-60 gamma-rays on the current gain of minimum-geometry bipolar transistors made from an advanced process. The data clearly illustrate the total-ionizing-dose vs particle-fluence behavior of this bipolar transistor produced by an advanced process. In particular, bulk damage from Co-60 gamma rays in bipolar transistors (base transport factor degradation) and surface damage in bipolar transistors from ionizing radiation (emitter-efficiency degradation) have been observed. The true equivalence between various types of radiation for this process technology has been determined on the basis of damage from the log K1 intercepts.

Description: It has previously been shown that the no-slip boundary conditions leads to a singularity at a moving contact line and that this presumes some form of slip. Present considerations on the energetics of slip due to shear stress lead to a yield stress boundary condition. A model for the distortion of the liquid state near solid boundaries gives a physical basis for this boundary condition. The yield stress condition is illustrated by an analysis of a slender drop rolling down an incline. That analysis provides a formula for the frictional drag resisting the drop movement. With the present boundary condition, the length of the slip region becomes a property of the fluid flow.

Description: Approaches used to control electrostatic discharge (ESD) at the JPL are discussed. ESD control problems generally occur in the following: (1) wrist straps; (2) outer garments that preclude the generation of static charge; and (3) materials, items, techniques, or processes permitting the development of a static charge. Consideration is given to the cleaning of antistatic materials, outside contracts, vapor degreasing, and electrostatically charged electrical cables.

Description: Focal properties, electron trajectory calculations, and geometries are given for two electron 'gun' lens systems that have a variety of applications in, for example, electron-neutral and electron-ion scattering experiments. One nine-lens system utilizes only electrostatic confinement and is capable of focusing electrons onto a fixed target with extremely small divergence angles, over a range of final energies 1-790 eV. The second gun lens system is a simpler three-lens system suitable for use in a uniform, solenoidal magnetic field. While the focusing properties of such a magnetically confined lens systenm are simpler to deal with, the system does illustrate features of electron extraction and Brillouin flow that have not been suitably emphasized in the literature.

Description: This paper presents a derivation of an exact closed-form expression of the integral chord-length distribution for the calculation of single-event upsets (SEUs) in an electronic memory cell, caused by cosmic rays. Results computed for two rectangular parallelepipeds using this exact expression are compared with those computed with Bradford's (1979) semiexact expression of C(x). It is found that the values of C(x) are identical for x equal or smaller than b but are vastly different for x greater than b. Moreover, while C(x) of Bradford gives reasonably accurate values of SEU rate for certain sets of computational parameters, it gives values more than 10 times larger than the correct values for other sets of parameters.

Description: This paper describes recent research advances made in the development of radiation-hardened piezoelectric quartz oscillators, hydrogen masers, and superconducting oscillators, with emphasis placed on the principles involved in the operation of these oscillators and the factors affecting the operation. Particular attention is given to the radiation-susceptibility studies of quartz-crystal resonators, the hydrogen-maser relaxation process and noise sources, and low-phase-noise superconducting oscillators. Diagrams of these devices and performance graphs are included.

Description: A novel contact regrowth technique for the formation of extremely low nonalloyed ohmic contacts is reported. The successful demonstration of this technique is reported on an InGaAs/InAlAs hot-electron transistor device. For the investigated InGaAs-based structure, the regrown contacting scheme reported includes an In(0.53)Ga(0.47)As layer, an InAs/GaAs strained-layer superlattice, and an InAs cap, all heavily doped n type with Si. A very low specific contact resistance of 1.8 x 10 to the -7th ohm sq cm to the base layer is obtained. The higher current densities achieved in the transistor characteristics are in close agreement with calculations, and a contact model is presented explaining the poor results of conventional nonalloyed contacts.

Description: The numerical scheme used by the present time-accurate FEM numerical method for incompressible Navier-Stokes equations, using primitive variables as the unknowns, is a Crank-Nicholson implicit treatment of all equation terms with central differencing for space derivatives. The introduction of a continuous auxilliary system in pseudo-time, with artificial compressibility, yields the incompressible solution at the advanced time level; time-accurate solutions are thereby obtained for two-dimensional fluid flows in a square cavity, in the cases of both an impulsively starting lid and an oscillating lid.

Description: A tunable solid state laser system, chromium-activated forsterite (Cr3+: Mg2SiO4), which has the potential for tunability from 850-1400 nm, is introduced. The characteristics of the host crystal are examined. Laser experiments and measurements are presented, including the observation of pulsed laser action at room temperature. The possibilities of the system are also considered.

Description: The paper describes an investigation of the velocity fluctuations in the free stream above an incompressible turbulent boundary layer developing at constant pressure. Measurements were performed in a wind tunnel with an rms level of axial velocity fluctuations of about 0.2 percent. The possibility of assessing the contributions to the rms level of the velocity fluctuations without using the high-pass filtering technique is demonstrated.

Description: A new very large scale integration (VLSI) design of a pipeline Reed-Solomon decoder is presented. The transform decoding technique used in a previous article is replaced by a time domain algorithm through a detailed comparison of their VLSI implementations. A new architecture that implements the time domain algorithm permits efficient pipeline processing with reduced circuitry. Erasure correction capability is also incorporated with little additional complexity. By using multiplexing technique, a new implementation of Euclid's algorithm maintains the throughput rate with less circuitry. Such improvements result in both enhanced capability and significant reduction in silicon area.

Description: Combinations of filters and subgrid scale stress models for large eddy simulation of the Navier-Stokes equations are examined by a priori tests and numerical simulations. The structure of the subgrid scales is found to depend strongly on the type of filter used, and consistency between model and filter is essential to ensure accurate results. The implementation of consistent combinations of filter and model gives more accurate turbulence statistics than those obtained in previous investigations in which the models were chosen independently from the filter. Results and limitations of the a priori test are discussed. The effect of grid refinement is also examined.

Description: Recent experiments have shown that, in rough-wall turbulent boundary layers, drag varies systematically with the spanwise aspect ratio lambda(z) (span/height) of roughness elements. In this paper, the effect of lambda(z) on turbulence structure has been examined. Based on lambda(z), the roughness in a transversely grooved surface with lambda(z) much greater than 1 is the opposite extreme of model plant canopies with lambda(z) much less than 1, studied in wind tunnels, whereas sandgrain is an intermediate type. Second-, third-, and fourth-order turbulence moments have been measured in turbulent boundary layers over transversely grooved and smooth surfaces and compared with available turbulence structure measurements over other types of surfaces. The near-wall turbulence structure is found to vary with lambda(z). The instantaneous motions involved in the flux of shear stress near the wall in smooth and transversely grooved surfaces are opposite in sign to those in three-dimensional roughness. The former is explained in terms of hairpin vortices alone, while the latter group is modeled to have an additional vortex (the so-called necklace vortex which straddles a three-dimensional roughness element near its base).

Description: The stability of inviscid swirling gas flows to small nonaxisymmetric perturbations is considered. For small Brunt-Vaisala frequencies, the problem reduces to the classical Sturm-Liouville form and the oscillation theorem can be applied. The resulting necessary and sufficient stability condition is compared to various criteria in the literature and a limited numerical study of isothermal rigidly rotating Poiseuille flow. For given azimuthal and axial wavenumbers, it is found numerically that the higher inertial modes become unstable for successively lower Rossby numbers and that this sequence of critical values approaches the theoretical value from above.

Description: The extension of the concept of vortex singularities, developed by Saffman and Meiron (1986) for the case of two-dimensional point vortices in an incompressible vortical flow, to the three-dimensional case of vortex sticks (vortons) is investigated analytically. The derivation of the governing equations is explained, and it is demonstrated that the formulation obtained conserves total vorticity and is a weak solution of the vorticity equation, making it an appropriate means for representing three-dimensional vortical flows with limited numbers of vortex singularities.

Description: The use of liquid and gas phase sulfur pretreatment of the surface of InP as a way to form a near-ideal passivated surface prior to chemical vapor deposition of SiO2 was investigated. Results of high-frequency and quasi-static capacitance-voltage measurements, as well as enhancement mode insulated gate field-effect transistor (FET) transductance and drain current stability studies, all support the efficacy of this approach for metal-insulator-semiconductor application of this semiconductor. In particular, surface state values in the range of 10 to the 10th to a few 10 to the 11th/sq cm per eV and enhancement mode FET drain current drifts of less than 5 percent over a 12 h test period were measured.

Description: Extended measurements and theory on the recently developed monolithic wavelength demultiplexer consisting of voltage-tunable superlattice p-i-n photodetectors in a waveguide configuration are discussed. It is shown that the device is able to demultiplex and detect two optical signals with a wavelength separation of 20 nm directly into different electrical channels at a data rate of 1 Gb/s and with a crosstalk attenuation varying between 20 and 28 dB, depending on the polarization. The minimum acceptable crosstalk attenuation at a data rate of 100 Mb/s is determined to be 10 dB. The feasibility of using the device as a polarization angle sensor for linearly polarized light is also demonstrated. A theory for the emission of photogenerated carriers out of the quantum wells is included, since this is potentially a speed limiting mechanism in these detectors. It is shown that a theory of thermally assisted tunneling by polar optical phonon interaction is able to predict emission times consistent with the observed temporal response.

Description: Unarmed plastic projectiles can be equipped with small axisymmetric cavities for the generation of intense tones that are useful in training maneuvers. Attention is presently given to the simulation of rainfall in an airstream and the effect of rain droplet impingement on the nose of projectiles, and especially to any penetration or accumulation of water at the base of the cavity that might increase the fundamental cavity frequency and/or reduce the intensity of sound production during rain conditions.

Description: This letter presents a method for calculating the even and odd mode impedances of broadside coupled cylindrical stiplines using the conformal mapping technique. Closed form expressions are presented for calculating the even and odd mode characteristic impedances. The data for even and odd mode impedances are presented. The analysis can also be extended to warped broadside coupled striplines.

Description: A time-efficient simulation technique was developed for modeling the energy deposition by incident protons in modern integrated circuits. To avoid the excessive computer time required by many proton-effects simulators, a stochastic method was chosen to model the various physical effects responsible for energy deposition by incident protons. Using probability density functions to describe the nuclear reactions responsible for most proton-induced memory upsets, the simulator determines the probability of a proton hit depositing the energy necessary for circuit destabilization. This factor is combined with various circuit parameters to determine the expected error-rate in a given proton environment. An analysis of transient or dose-rate effects is also performed. A comparison to experimental energy-disposition data proves the simulator to be quite accurate for predicting the expected number of events in certain integrated circuits.

Description: Recent work on the equilibrium shapes of a rotating spheroid and drop shape oscillations is reviewed. The related theoretical aspects of the equilibrium shapes of a rotating drop, the stability, shape oscillations, gravitational forces, and drop fission are examined. Experimental findings on figures of a rotating drop in an immiscible system, drop oscillations in an immiscible system, oscillations of a rotating drop, compound drop oscillations, and drop dynamics in space are addressed.

Description: Barrier height enhancement of an InP-based p(+)n-Ga(0.47)In(0.53)As Schottky diode grown by MBE has been demonstrated for infra-red photodetector applications. A barrier height of 0.35 eV for n-Ga(0.47)In(0.53)As Schottky barrier diodes, was increased to the effective barrier height of 0.55 eV, with a p(+)-Ga(0.47)In(0.53)As surface layer of 30 nm thick. The results show a reverse leakage current density of 0.0015 A/sq cm and a junction capacitance of 0.3 pF, which are comparable to those of p-Ga(0.47)In(0.53)As Schottky-barrier diodes at a reverse bias voltage of 5 V.

Description: A formulation is presented by which any iteration process for obtaining the entropy increase in the flow of a one-dimensional steady nozzle is eliminated, and the simple solution of a quadratic equation is obtained. The proper parameters are then explicitly seen in the equation, and their effects on the solution are easily determined. Since only one root of the equation is physically admissible, entropy production, and therefore the shock wave, are uniquely determined by this set of parameters.

Description: Al(0.3)Ga(0.7)As/Al(0.05)Ga(0.95)As double-heterostructure light-emitting diodes (LEDs) were successfully grown for the first time by liquid phase epitaxy on a GaAs-coated Si substrate that was prepared by a sequential process of migration-enhanced epitaxy and molecular beam epitaxy. The edge-emitting LEDs had diode ideality factors of 1.54 at a forward-biased voltage higher than 0.9 V and external quantum efficiencies of 0.0033 W/A per facet. This efficiency is 50 times higher than the previously reported value, and is on the same order as that of AlGaAs homojunction LEDs fabricated on the GaAs substrates by liquid phase epitaxy.

Description: The properties of the Karhunen-Loeve expansion of a strongly inhomogeneous random process are examined with emphasis on applications to turbulent flow fields. The ability of the KL expansion to represent functions that have both slow and rapid variations in a relatively small number of expansion terms is tested on a one-dimensional model based on the forced Burgers' equation. The rate of the convergence of the expansion is evaluated, and its dependence on the Reynolds number is determined. It is shown that the KL eigenfunctions possess wall boundary layers attached to outer structures that are independent of the Reynolds number (at high Reynolds numbers). It is also shown that the spectrum of eigenvalues is broad at large Reynolds numbers, requiring many terms to represent higher-order derivatives of the function.

Description: The flow in a two-dimensional curved channel driven by an azimuthal pressure gradient can become linearly unstable due to axisymmetric perturbations and/or nonaxisymmetric perturbations depending on the curvature of the channel and the Reynolds number. For a particular small value of curvature, the critical neighborhood of this curvature value and critical Reynolds number, nonlinear interactions occur between these perturbations. The Stuart-Watson approach is used to derive two coupled Landau equations for the amplitudes of these perturbations. The stability of the various possible states of these perturbations is shown through bifurcation diagrams. Emphasis is given to those cases which have relevance to external flows.

Description: Employing a structure consisting of n(+)-InAs/InGaAs and InAs/GaAs strained-layer superlattices (SLSs) grown by molecular beam epitaxy on GaAs films, nonalloyed contact resistances less than 8.5 x 10 to the -8th ohm sq cm have been obtained. Self-consistent simulations show that these extremely small nonalloyed contact resistances are due to the suppression of the depletion depth in the GaAs channel and tunneling through the SLS layer. Similar structures on InGaAs channels have led to nonalloyed specific contact resistances of about 1.5 x 10 to the -8th ohm sq cm. These results represent the smallest figures reported for these important material systems.

Description: A method of analysis for coupled cylindrical striplines filled with multilayered dielectrics is presented that uses a variational technique in the space domain. Coupled-mode analysis is presented for the case of a pair of coupled circular arc strips arbitrarily located between cylindrical ground planes filled with multilayered dielectrics. An even- and odd-mode approach is used for the analysis of shielded cylindrically curved edge-coupled pairs of broad-side parallel strips (broad-side, edge-coupled cylindrical striplines). The effect of environmental changes on an otherwise planar structure is also studied by extending the present analysis to cylindrically warped coupled striplines.

Description: To study thermocapillary flows in a two-dimensional thin liquid layer with heat fluxes imposed on the free surface experimentally, a long tray configuration was employed to simulate the infinite layer. The surface temperature distribution due to thermocapillary convection for different flow regimes was measured and compared with theorectical predictions. A short tray configuration was also employed to study the end wall effects (insulating or conducting). The results show that, for a strong convection flow with an insulating wall as the boundary, the surface temperature distribution became quite uniform. Consequently, the thermocapillary driving force was greatly reduced. On the other hand, a strong fluid motion always existed adjacent to the conducting wall because of the large surface temperature gradient near the wall.

Description: The 'transfinite element method' (TFEM) proposed by Tamma and Railkar (1987 and 1988) for the analysis of linear and nonlinear heat-transfer problems is described and demonstrated. The TFEM combines classical Galerkin and transform approaches with state-of-the-art FEMs to obtain a flexible hybrid modeling scheme. The fundamental principles of the TFEM and the derivation of the governing equations are reviewed, and numerical results for sample problems are presented in extensive graphs and briefly characterized. Problems analyzed include a square plate with a hole, a rectangular plate with natural and essential boundary conditions and varying thermal conductivity, the Space Shuttle thermal protection system, a bimaterial plate subjected to step temperature variations, and solidification in a semiinfinite liquid slab.

Description: Two factors which limit the complexity of GaAs MESFET VLSI circuits are considered. Power dissipation sets an upper complexity limit for a given logic circuit implementation and thermal design. Uniformity of device characteristics and the circuit configuration determines the electrical functional yield. Projection of VLSI complexity based on these factors indicates that logic chips of 15,000 gates are feasible with the most promising static circuits if a maximum power dissipation of 5 W per chip is assumed. While lower power per gate and therefore more gates per chip can be obtained by using a popular E/D FET circuit, yields are shown to be small when practical device parameter tolerances are applied. Further improvements in materials, devices, and circuits wil be needed to extend circuit complexity to the range currently dominated by silicon.

Description: The stability, capacity, and design of a nonlinear continuous neural network are analyzed. Sufficient conditions for existence and asymptotic stability of the network's equilibria are reduced to a set of piecewise-linear inequality relations that can be solved by a feedforward binary network, or by methods such as Fourier elimination. The stability and capacity of the network is characterized by the post synaptic firing rate function. An N-neuron network with sigmoidal firing function is shown to have up to 3N equilibrium points. This offers a higher capacity than the (0.1-0.2)N obtained in the binary Hopfield network. Moreover, it is shown that by a proper selection of the postsynaptic firing rate function, one can significantly extend the capacity storage of the network.

Description: The 10-micron intersubband absorption in quantum wells made of the silicon-based system, Si/Si(1-x)Ge(x), has been calculated. The necessary details of the effective-mass anisotropy are included in the present analysis. It is found that it is readily possible to achieve an absorption constant of order of 10,000/cm in Si quantum wells with current doping technology. For 110-line and 111-line growth directions, a further advantage of Si quantum wells is pointed out, namely, an allowed absorption at normal incidence due to the anisotropic effective mass in Si.

Description: Columnar, porous, magnetron-sputtered molybdenum and tungsten films show optimum performance as alkali metal thermoelectric converter electrodes at thicknesses less than 1.0 micron when used with molybdenum or nickel current collector grids. Power densities of 0.40 W/sq cm for 0.5-micron molybdenum films at 1200 K and 0.35 W/sq cm for 0.5-micron tungsten films at 1180 K were obtained at electrode maturity after 40-90 h. Sheet resistances of magnetron sputter deposited films on sodium beta-double-prime-alumina solid electrolyte (BASE) substrates were found to increase very steeply as thickness is decreased below about 0.3-double-prime 0.4-micron. The ac impedance data for these electrodes have been interpreted in terms of contributions from the bulk BASE and the porous electrode/BASE interface. Voltage profiles of operating electrodes show that the total electrode area, of electrodes with thickness less than 2.0 microns, is not utilized efficiently unless a fairly fine (about 1 x 1 mm) current collector grid is employed.

Description: The budgets for the Reynolds stresses and for the dissipation rate of the turbulence kinetic energy are computed using direct simulation data of a turbulent channel flow. The budget data reveal that all the terms in the budget become important close to the wall. For inhomogeneous pressure boundary conditions, the pressure-strain term is split into a return term, a rapid term, and a Stokes term. The Stokes term is important close to the wall. The rapid and return terms play different roles depending on the component of the term. A split of the velocity pressure-gradient term into a redistributive term and a diffusion term is proposed, which should be simpler to model. The budget data is used to test existing closure models for the pressure-strain term, the dissipation rate, and the transport rate. In general, further work is needed to improve the models.

Description: Thick films of YBa2Cu3O(7-x) have been deposited on highly polished alumina, magnesia spinel, nickel aluminum titanate (Ni-Al-Ti), and barium tetratitanate (Ba-Ti) substrates by the screen printing technique. Properties of the films were found to be highly sensitive to the choice of the substrate material. The film on Ba-Ti turned green after firing, due to a reaction with the substrate and were insulating. A film on Ni-Al-Ti had a Tc (onset) of about 95 K and lost 90 percent of its resistance by about 75 K. However, even at 4 K it was not fully superconducting, possibly due to a reaction between the film and the substrate and interdiffusion of the reaction products. The film on alumina had Tc (onset) of about 96 K, Tc (zero) of about 66 K, and Delta Tc of about 10 K. The best film was obtained on spinel and had Tc (onset) of about 94 K, zero resistance at 81 K, and a transition width of about 7 K.

Description: A cylindrical region filled with absorbing-emitting material is cooled by radiation to surroundings at a much lower temperature. A solution is found showing that, for each set of parameters, the transient radial temperature distribution reaches a fixed shape, although the temperatures are decreasing with time. This 'fully developed' transient region is characterized by having a constant emittance based on instantaneous values of the cylinder heat loss and mean temperature. This emittance depends only on the optical radius of the cylinder and the scattering albedo. The emittance is lower than that for a cylinder at uniform temperature. This arises from the larger local cooling and, hence, reduced temperatures of the outer layers of the cylinder. An examination of this transient emittance provides the ranges of parameters within which the simplification can be made that the cylinder has uniform radial temperature distribution throughout the cooling process.

Description: The nonlinear evolution of periodic disturbances on vortex trails is considered. In addition to following small initial perturbations, large amplitude initial disturbances of the vortex trails are also studied. It is shown that the equations support a rich variety of essentially nonlinear solutions including unbounded and quasisteady ones. These solutions are found to correspond to various modes of vortex clustering in the physical plane. At the close of the paper, comparisons of these results with recent numerical and experimental findings on the wakes behind stationary cylinders, and also transversely oscillating bluff objects, are made.

Description: A new model is presented which permits the prediction of the resonant frequencies created by antipodal finline waveguide to microstrip transitions. The transition is modeled as a tapered transmission line in series with an infinite set of coupled resonant circuits. The resonant circuits are modeled as simple microwave resonant cavities of which the resonant frequencies are easily determined. The model is developed and the resonant frequencies determined for several different transitions. Experimental results are given to confirm the models.

Description: An infinitely thin shear layer emanating from a semi-infinite flat plate subjected to acoustic excitation is considered. The flow field outside the excited shear layer is computed employing a source distribution approach. Results are given for the region of the velocity field that cannot easily be obtained by analytical approximations.

Description: The performance is reported of a field emission array characterized for the purpose of replacing the filament in a trapped ion frequency standard. This dark electron emitter eliminates the need for the interference filter currently used in the trapped ion standard. While reducing the filament's unwanted light, this filter causes a significant reduction in the signal. The magnetic field associated with the filament is also eliminated, thus potentially improving the present stability of the trapped ion standard. The operation of the filament in the present system is described, as well as the associated concerns. The cathode considered for the filament's replacement is then described along with the experimental system. Experimental results, observations, and conclusions are presented.

Description: The frequency and intensity of thunderstorms around the Kennedy Space Center (KSC) has affected scheduled launch, landing, and other ground operations for many years. In order to protect against and provide safe working facilities, KSC has performed and hosted several studies on lightning phenomena. For the reasons mentioned above, KSC has established the Atmospheric Science Field Laboratory (ASFL). At these facilities KSC launches wire-towing rockets into thunderstorms to trigger natural lightning to the launch site. A program named Rocket Triggered Lightning Program (RTLP) is being conducted at the ASFL. This report calls for two of the experiments conducted in the summer 1988 Rocket Triggered Lightning Program. One experiment suspended an electric field mill over the launching areas from a balloon about 500 meters high to measure the space charges over the launching area. The other was to connect a waveform recorder to a nearby distribution power line to record currents and voltages wave forms induced by natural and triggered lightning.

Description: Many problems in computational fluid dynamics (CFD) involve the calculation of flow fields within or around complex geometric configurations. The flow solution is computed on a computational grid. The construction of the grid is one of the major difficulties in the application of CFD to the analysis of flow about actual aircraft configurations. Due to geometric complexity, the grid has to be constructed in simple subregions and then all of these subgrids have to be pieced together to form a complete grid for the entire flow field. The entire grid, which is called a composite grid because it is formed from many parts, may have common regions. In either case, the computation of the flow field, using any numerical algorithm, will require the transfer of information between individual subgrids. The transfer of information is more difficult with overlapping grids. Algorithms have been developed and tested for automating the transfer of information between two overlapping grids.

Description: An effort directed at developing improved transitional models was initiated. The focus of this work was concentrated on the critical assessment of a popular existing transitional model developed by McDonald and Fish in 1972. The objective of this effort was to identify the shortcomings of the McDonald-Fish model and to use the insights gained to suggest modifications or alterations of the basic model. In order to evaluate the transitional model, a compressible boundary layer code was required. Accordingly, a two-dimensional compressible boundary layer code was developed. The program was based on a three-point fully implicit finite difference algorithm where the equations were solved in an uncoupled manner with second order extrapolation used to evaluate the non-linear coefficients. Iteration was offered as an option if the extrapolation error could not be tolerated. The differencing scheme was arranged to be second order in both spatial directions on an arbitrarily stretched mesh. A variety of boundary condition options were implemented including specification of an external pressure gradient, specification of a wall temperature distribution, and specification of an external temperature distribution. Overall the results of the initial phase of this work indicate that the McDonald-Fish model does a poor job at predicting the details of the turbulent flow structure during the transition region.

Description: Detailed measurements were made of energy transfer among the scales of motion in incompressible turbulent fields at low Reynolds numbers generated by direct numerical simulation. It was observed that although the transfer resulted from triad interactions that were non-local in k space, the energy always transferred locally. The results are consistent with the notion of non-uniform advection of small weak eddies by larger and stronger ones, similar to transfer processes in the far dissipation range at high Reynolds numbers.

Description: Employing numerical simulations of 3-D homogeneous shear flow, the associated multifractal spectra of the energy dissipation, scalar dissipation and vorticity fields were calculated. The results for (128) cubed simulations of this flow, and those obtained in recent experiments that analyzed 1- and 2-D intersections of atmospheric and laboratory flows, are in some agreement. A two-scale Cantor set model of the energy cascade process which describes the experimental results from 1-D intersections quite well, describes the 3-D results only marginally.

Description: A detailed study of the intercomponent energy transfer processes by the pressure-strain-rate in homogeneous turbulent shear flow is presented. Probability density functions (pdf's) and contour plots of the rapid and slow pressure-strain-rate show that the energy transfer processes are extremely peaky, with high-magnitude events dominating low-magnitude fluctuations, as reflected by very high flatness factors of the pressure-strain-rate. A concept of the energy transfer class was applied to investigate details of the direction as well as magnitude of the energy transfer processes. In incompressible flow, six disjoint energy transfer classes exist. Examination of contours in instantaneous fields, pdf's and weighted pdf's of the pressure-strain-rate indicates that in the low magnitude regions all six classes play an important role, but in the high magnitude regions four classes of transfer processes, dominate. The contribution to the average slow pressure-strain-rate from the high magnitude fluctuations is only 50 percent or less. The relative significance of high and low magnitude transfer events is discussed.

Description: New definitions of entrainment and mixing based on the passive scalar field in the plane mixing layer are proposed. The definitions distinguish clearly between three fluid states: (1) unmixed fluid, (2) fluid engulfed in the mixing layer, trapped between two scalar contours, and (3) mixed fluid. The difference betwen (2) and (3) is the amount of fluid which has been engulfed during the pairing process, but has not yet mixed. Trends are identified from direct numerical simulations and extensions to high Reynolds number mixing layers are made in terms of the Broadwell-Breidenthal mixing model. In the limit of high Peclet number (Pe = ReSc) it is speculated that engulfed fluid rises in steps associated with pairings, introducing unmixed fluid into the large scale structures, where it is eventually mixed at the Kolmogorov scale. From this viewpoint, pairing is a prerequisite for mixing in the turbulent plane mixing layer.

Description: Several direct numerical simulations were performed and analyzed to study various aspects of the early development of mixing layers. Included are the phase jitter of the large-scale eddies, which was studied using a 2-D spatially-evolving mixing layer simulation; the response of a time developing mixing layer to various spanwise disturbances; and the sound radiation from a 2-D compressible time developing mixing layer.

Description: In the last few years, more and more evidence has emerged suggesting that transition to turbulence may be viewed as a succession of bifurcations to deterministic chaos. Most experimental and numerical observations have been restricted to Rayleigh-Benard convection and Taylor-Couette flow between concentric cylinders. An attempt is made to accurately describe the bifurcation sequence leading to chaos in a 2-D temporal free shear layer on the beta-plane. The beta-plane is a locally Cartesian reduction of the equations describing the dynamicss of a shallow layer of fluid on a rotating spherical planet. It is a valid model for large scale flows of interest in meteorology and oceanography.

Description: Full turbulence simulations at low Reynolds numbers were made for the single-step, irreversible, bimolecular reaction between non-premixed reactants in isochoric, decaying homogeneous turbulence. Various initial conditions for the scalar field were used in the simulations to control the initial scalar dissipation length scale, and simulations were also made for temperature-dependent reaction rates and for non-stoichiometric and unequal diffusivity conditions. Joint probability density functions (pdf's), conditional pdf's, and various statistical quantities appearing in the moment equations were computed. Preliminary analysis of the results indicates that compressive strain-rate correlates better than other dynamical quantities with local reaction rate, and the locations of peak reaction rates seem to be insensitive to the scalar field initial conditions.

Description: Recent studies of turbulent shear flows have shown that many of their important kinematical and dynamical properties can be more clearly understood by describing the flows in terms of individual events or streamline patterns. These events or flow regions are studied because they are associated with relatively large contributions to certain average properties of the flow, for example kinetic energy, Reynolds stress, or to particular processes in the flow, such as mixing and chemical reactions, which may be concentrated at locations where streamlines converge for fast chemical reactions (referred to as convergence or C regions), or in recirculating eddying regions for slow chemical reactions. The aim of this project was to use the numerical simulations to develop suitable criteria for defining these eddying or vortical zones. The C and streaming (S) zones were defined in order to define the whole flow field. It is concluded that homogeneous and sheared turbulent flow fields are made up of characteristic flow zones: eddy, C, and S zones. A set of objective criteria were found which describe regions in which the streamlines circulate, converge or diverge, and form high streams of high velocity flow.

Description: The subharmonic resonance phenomenon in a spatially evolving mixing layer is studied using direct simulations of the 2-D Navier-Stokes equations. The computational domain extends to + or - infinity in the cross-stream direction with U(1) = 1.25 and U(2) = 0.25 imposed at + infinity and - infinity respectively. The domain is finite in the streamwise direction with inflow and outflow boundary conditions imposed at x/delta sub omega = 0 and 100, respectively. A hyperbolic-tangent mean velocity profile is assumed at the inlet and the Reynolds number based on the inlet vorticity thickness and velocity difference is Re = 600. It is observed that the phase angle between the fundamental and its subharmonic plays a key role in the spatial development of these modes. Contour plots of vorticity show that varying the phase will have a dramatic effect on the dynamics of the vortices. Pairing or shredding is observed depending on the phase. Fourier decomposition of the time traces show that the fundamental grows, saturates and decays with the downstream distance. The subharmonic has a similar behavior. However, the level at which the modes will saturate is affected by the phase. At 0 deg phase, it was found that as the fundamental saturates, the growth rate of the subharmonic is enhanced. At 90 deg phase, it was found that as the fundamental saturates, the growth rate of the subharmonic is inhibited. In the later case, the growth rate of the subharmonic recovers after saturation of the fundamental. These results are in qualitative agreement with experimental data.

Description: The numerical simulation of incompressible spatially-developing shear flows poses a special challenge to computational fluid dynamicists. The Navier-Stokes equations are elliptic and boundary equations need to be specified at the inflow and outflow boundaries in order to compute the fluid properties within the region of interest. It is, however, difficult to choose inflow and outflow conditions corresponding to a given experimental situation. Furthermore the effects that changes in the boundary conditions or in the size of the computational domain may induce on the global dynamics of the flow are presently unknown. These issues are examined in light of recent developments in hydrodynamic stability theory. The particular flow considered is the spatial mixing layer but it was expected that similar phenomena were bound to occur in other cases such as channel flow, the boundary layer, etc. A short summary of local/global and absolute/convective instability concepts is given. The results of numerical simulations are presented which strongly suggest that global resonances may be triggered in domains of finite streamwise extent although the evolution of the perturbation vorticity field is everywhere locally convective. A relationship between finite domains and pressure sources which might help in devising a scheme to eliminate these difficulties is discussed.

Description: A spatially-developing plane mixing layer was analyzed for chaotic behavior. A direct numerical simulation of the Navier-Stokes equations in a 2-D domain infinite in y and having inflow-outflow boundary conditions in x was used for data. Spectra, correlation dimension and the largest Lyapunov exponent were computed as functions of downstream distance x. When forced at a single (fundamental) frequency with maximum amplitude, the flow is periodic at the inflow but becomes aperiodic with increasing x. The aperiodic behavior is caused by the presence of a noisy subharmonic caused by the feedback between the necessarily nonphysical inflow and outflow boundary conditions. In order to overshadow this noise the flow was also studied with the same fundamental forcing and added random forcing of amplitude upsilon prime sub R/delta U = 0.01 at the inlet. Results were qualitatively the same in both cases: for small x, spectral peaks were sharp and dimension was nearly 1, but as x increased a narrowband spectral peak grew, spectra decayed exponentially at high frequencies and dimension increased to greater than 3. Based on these results, the flow appears to exhibit deterministic chaos. However, at no location was the largest Lyapunov exponent found to be significantly greater than zero.

Description: Experiments on wall-bounded shear flows (channel flows and boundary layers) have indicated that the turbulence in the region close to the wall exhibits a characteristic intermittently formed pattern of coherent structures. For a quantitative study of coherent structures it is necessary to make use of conditional sampling. One particularly successful sampling technique is the Variable Integration Time Averaging technique (VITA) first explored by Blackwelder and Kaplan (1976). In this, an event is assumed to occur when the short time variance exceeds a certain threshold multiple of the mean square signal. The analysis presented removes some assumptions in the earlier models in that the effects of pressure and viscosity are taken into account in an approximation based on the assumption that the near-wall structures are highly elongated in the streamwise direction. The appropriateness of this is suggested by the observations but is also self consistent with the results of the model which show that the streamwise dimension of the structure grows with time, so that the approximation should improve with the age of the structure.

Description: Effects of organized turbulent structures on the propagation of an optical beam in a homogeneous shear flow were studied. A passive-scalar field in a computed turbulent shear flow is used to represent index-of-refraction fluctuations, and phase errors induced in a coherent optical beam by turbulent fluctuations are computed. The organized vortical structures produce a scalar distribution with elongated regions of intense fluctuations which have an inclination with respect to the mean flow similar to that of the characteristic hairpin eddies. It is found that r.m.s. phase error is minimized by propagating approximately normal to the inclined vortical structures. Two-point correlations of vorticity and scalar fluctuation suggest that the regions of intense scalar fluctuation are produced primarily by the hairpin eddies.

Description: An analysis is presented of how a plane boundary affects the structure of turbulence in a sheared free stream. A uniform-shear boundary layer (USBL) is formulated with slip velocity condition at the surface, and inhomogeneous rapid distortion theory is applied. The effects of blocking by the surface on the turbulence structure in USBL is compared with those in the shear-free boundary layer (SFBL). Shear produces highly anisotropic eddies elongated in the flow direction. The vertical velocity variance is reduced with shear at all heights, roughly in proportion to the reduction in the homogeneous value, but the shape of the profile remains unchanged only near the surface. The streamwise integral scales increase with shear, indicating elongation of the streamwise extent of eddies.

Description: In wall-bounded shear flows the transition to turbulence through localized disturbances goes through a pattern starting with a development of shear layers. The localized normal velocity fluctuations induce normal vorticity through the lift-up effect. These shear layers become unstable to secondary disturbances, and if the amplitudes of the disturbances are large enough, a turbulent spot develops. Investigations of the spot in boundary layers has shown that the turbulent part of the spot is very similar to a fully developed boundary layer. Wygnanski et al. (1976) showed that the mean profile at the center-symmetry plane has a logarithmic region and Johansson et al. (1987) showed that both the higher-order statistics and flow structures in the spot were the same as in the corresponding fully developed flow. In what respects the turbulence inside the Poiseuille spot is similar to fully developed turbulent channel flow is studied. The numerically simulated spot is used, where the characteristics inside the spot are compared to those of the wave packet in the wingtip area. A recent experimental investigation of the velocity field associated with the Poiseuille spot by Klingmann et al. is used for comparison.

Description: Space-time evolution of near wall flow structures is described by conditional sampling methods, in which conditional averages are formed at various stages of development of shear layer structures. The development of spanwise asymmetry of the structures was found to be important in the creation of the structures and for the process of turbulence production.

Description: It is well known that turbulent mixing layers are dominated by large scale, fairly coherent structures, and that these structures are related to the stability characteristics of the flow. These facts have led researchers to attempt controlling such flows by selectively forcing certain unstable modes, which can in addition have the effect of suppressing other modes. Much of the work on controlling the mixing layer has relied on forcing 2-D instabilities. The results of forcing 3-D instabilities are addressed. The objectives of the work are twofold: to understand how a mixing layer responds to 3-D perturbations, and to test the validity of an amplitude expansion in predicting the mixing layer development. The amplitude expansion could be very useful in understanding and predicting the 3-D response of the flow to a variety of initial conditions.

Description: Data obtained from the numerical simulation of a 2-D mixing layer were used to study the feasibility of using the instantaneous concentration of a passive scalar for detecting the typical coherent structures in the flow. The study showed that this technique works quite satisfactorily and yields results similar to those that can be obtained by using the instantaneous vorticity for structure detection. Using the coherent events educed by the scalar conditioning technique, the contribution of the coherent events to the total turbulent momentum and scalar transport was estimated. It is found that the contribution from the typical coherent events is of the same order as that of the time-mean value. However, the individual contributions become very large during the pairing of these structures. The increase is particularly spectacular in the case of the Reynolds shear stress.

Description: An incompressible, time developing 3-D mixing layer with idealized initial conditions was simulated numerically. Consistent with the suggestions from experimental measurements, the braid region between the dominant spanwise vortices or rolls develops longitudinal vortices or ribs, which are aligned upstream and downstream of a roll and produce spanwise distortion of the rolls. The process by which this distortion occurs is explained by studying a variety of quantities of dynamic importance (e.g., production of enstrophy, vortex stretching). Other quantities of interest (dissipation, helicity density) are also computed and discussed. The currently available simulation only allows the study of the early evolution (before pairing) of the mixing layer. New simulations in progress will relieve this restriction.

Description: To unravel the liquid-jet breakup process in the nondilute region, a newly developed system of real-time X-ray radiography, an advanced digital image processor, and a high-speed video camera were used. Based upon recorded X-ray images, the inner structure of a liquid jet during breakup was observed. The jet divergence angle, jet breakup length, and fraction distributions along the axial and transverse directions of the liquid jets were determined in the near-injector region. Both wall- and free-jet tests were conducted to study the effect of wall friction on the jet breakup process.

Description: A review of the application of single particle hydrodynamics in models for the exchange of interphase momentum in continuum models of multiphase flow is presented. Considered are the equations of motion for a laminar, mechanical two phase flow. Inherent to this theory is a model for the interphase exchange of momentum due to drag between the dispersed particulate and continuous fluid phases. In addition, applications of two phase flow theory to de-mixing flows require the modeling of interphase momentum exchange due to lift forces. The applications of single particle analysis in deriving models for drag and lift are examined.

Description: Experimental evidence for the existence of shear induced migration processes is reviewed and the mechanism by Leighton and Acrivos (1987b) is described in detail. The proposed mechanism is shown to lead to the existence of an additional shear induced migration in the presence of gradients in shear stress such as would be found in Poiseuille flow, and which may be used to predict the amplitude of the observed short-term viscosity increase. The concentration and velocity profiles which result from such a migration are discussed in detail and are compared to the experimental observations of Karnis, Goldsmith and Mason (1966).

Description: Modeling of cross-guide couplers based on the theory of equivalent electric and magnetic dipoles of an aperture is described. Additional correction factors due to nonzero wall thickness and large aperture are also included in this analysis. Comparisons of the measured and calculated results are presented for cross-guide couplers with circular or cross-shaped coupling apertures. A cross-guide coupler was designed as a component of the C-band feed to support the Phobos mission.