ALBERT

Description: This paper reports a new balance for the measurement of three components of force - lift, drag and pitching moment - in impulsively starting flows which have a duration of about one millisecond. The basics of the design of the balance are presented and results of tests on a 15 deg semi-angle cone set at incidence in the T4 shock tunnel are compared with predictions. These results indicate that the prototype balance performs well for a 1.9 kg, 220 mm long model. Also presented are results from initial bench tests of another application of the deconvolution force balance to the measurement of thrust produced by a 2D scramjet nozzle.

Description: Measurements of wing buffeting, using root strain gages, were made in the NASA Langley 0.3 m cryogenic wind tunnel to refine techniques which will be used in larger cryogenic facilities such as the United States National Transonic Facility (NTF) and the European Transonic Wind Tunnel (ETW). The questions addressed included the relative importance variations in frequency parameter and Reynolds number, the choice of model material (considering both stiffness and damping) and the effects of static aeroelastic distortion. The main series of tests was made on three half models of slender 65 deg delta wings with a sharp leading edge. The three delta wings had the same planform but widely differing bending stiffnesses and frequencies (obtained by varying both the material and the thickness of the wings). It was known that the steady flow on this configuration would be insensitive to variations in Reynolds number. On this wing at vortex breakdown the spectrum of the unsteady excitation is unusual, having a sharp peak at particular frequency parameter. Additional tests were made on one unswept half-wing of aspect ratio 1.5 with an NPL 9510 aerofoil section, known to be sensitive to variations in Reynolds number at transonic speeds. The test Mach numbers were M = 0.21 and 0.35 for the delta wings and to M = 0.30 for the unswept wing. On this wing the unsteady excitation spectrum is fairly flat (as on most wings). Hence correct representation of the frequency parameter is not particularly important.

Description: The concept of the well-known Langley plot technique, used for the calibration of ground-based instruments, has been generalized for application to satellite instruments. In polar regions, near summer solstice, the solar backscattered ultraviolet (SBUV) instrument on the Nimbus 7 satellite samples the same ozone field at widely different solar zenith angles. These measurements are compared to assess the long-term drift in the instrument calibration. Although the technique provides only a relative wavelength-to-wavelength calibration, it can be combined with existing techniques to determine the drift of the instrument at any wavelength. Using this technique, we have generated a 12-year data set of ozone vertical profiles from SBUV with an estimated accuracy of +/- 5% at 1 mbar and +/- 2% at 10 mbar (95% confidence) over 12 years. Since the method is insensitive to true changes in the atmospheric ozone profile, it can also be used to compare the calibrations of similar SBUV instruments launched without temporal overlap.

Description: Geologic orbital photography

Description: The transportation cost associated with space materials processing were studied to determine the feasibility of space manufacturing. The assumptions use to determining the cost estimates for a 12 year planning period are listed, and the orbitor is described in terms of payloads. Shuttle operational costs, ground operational costs, and nonrecurring investment and development costs were analyzed.

Description: Test facility and equipment to determine very high Reynolds number effects associated with large boost vehicles

Description: Hydrogen slush density instrumentation for field measurements of slush mass after calibration with reference system

Description: Using Mossbauer effect and laser interferometry to determine extremely small amplitudes for vibration measurements and calibration of scale models

Description: The application of computer techniques for solving Navier-Stokes equations in support of wind tunnel tests is discussed. The ILLIAC IV computer is considered for this purpose and its limitations are analyzed. The author states that improved computers will make it possible to solve many aerodynamic problems and reduce the amount of wind tunnel testing required for adequate data processing.

Description: Research within NASA relating to the nature of lift-induced vortex wakes behind large aircraft and the means whereby the hazard they represent to smaller aircraft can be alleviated is reviewed. The research, carried out in ground based facilities and in flight shows that more rapid dispersion of the wake can be effected by several means and that the modification of span-loading by appropriate flap deflection holds promise of early practical application.

Description: Digital generation of acceleration voltage for mass spectrometer, and development of low power, nondestructive readout, plated-wire memory

Description: Pulse height analyzer, imaging astronomical photometer, and secondary electron conduction vidicon for space application

Description: Atmospheric entry sampling system, and prototype mass spectrometer for planetary atmospheric analysis

Description: A thoroughly documented experiment is reported that was specifically designed to test and guide computations of the interaction of an impinging shock wave with a turbulent boundary layer. Detailed mean flow field and surface data are presented for two shock strengths which resulted in attached and separated flows, respectively. Numerical computations are used to illustrate the dependence of the computations on the particulars of the turbulence models. Models appropriate for zero pressure gradient flows predicted the overall features of the flow fields, but were deficient in predicting many of the details of the interaction regions. Improvements to the turbulence model parameters were sought through a combination of detailed data analysis and computer simulations which tested the sensitivity of the solutions to model parameter changes. Computer simulations using these improvements are presented and discussed.

Description: A method is developed for solving the laminar and turbulent compressible boundary layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent layer, shock wave interactions. Several Navier-Stokes solutions are obtained for each of the laminar boundary layer, shock wave interactions considered. Comparison of these solutions indicates a first order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow. Comparison of the present boundary layer solutions with the Navier-Stokes solutions and with data for a given Mach number indicates that as long as the separation bubble is small, the boundary layer approximation yields solutions whose accuracy is comparable to the Navier-Stokes solutions.

Description: The Magellan spacecraft has been aerobraked into a 197 x 541 km near-circular orbit around Venus from which it is conducting a high-resolution gravity mapping mission. This was the first interplanetary aerobrake maneuver and involved flying the spacecraft through the upper reaches of the Venusian atmosphere 730 times over a 70 day period. Round-trip light-time varied from 9.57 to 18.83 minutes during this period. Navigation for this dynamic phase of the Magellan mission was planned and executed in the face of budget-driven down-sizing with all spacecraft safe modes disabled and a flight-team one-third the size of comparable interplanetary missions. Successful execution of this manuever using spacecraft hardware not designed to operate in a planetary atmosphere, demonstrated a practical cost-saving technique for both large and small future interplanetary missions.

Description: Multispectral imagery of aerial remote sensors and television simulation for terrain analysis

Description: Aerial infrared scanners for thermal mapping and multispectral sensing

Description: Investigating infrared scanners for thermal mapping and multispectral sensing

Description: Photographic applications of NASA Earth Resources Survey Program

Description: The formulation of mathematical models of aeronautical systems for simulation or other purposes, involves the transformation of aerodynamic stability derivatives. It is shown that these derivatives transform like the components of a second order tensor having one index of covariance and one index of contravariance. Moreover, due to the equivalence of covariant and contravariant transformations in orthogonal Cartesian systems of coordinates, the transformations can be treated as doubly covariant or doubly contravariant, if this simplifies the formulation. It is shown that the tensor properties of these derivatives can be used to facilitate their transformation by symbolic mathematical computation, and the use of digital computers equipped with formula manipulation compilers. When the tensor transformations are mechanised in the manner described, man-hours are saved and the errors to which human operators are prone can be avoided.

Description: The pressure sensor for the Tropical Wind Energy conversion and Reference Level Experiment (TWERLE) is described. Key design features of the sensor are: capacitive coupling, reference at midrange, up-down counting, passive oven, storage at flight pressure and prelaunch calibration. Sensor specifications are given which are based on the production results of 440 units. Drift, as estimated from simulated life tests, is 1 mb per 6 months. The overall weight of the sensor, including thermal package, is 180 g.

Description: A closed-form solution for the sound radiation from multipole sources imbedded in an infinite cylindrical jet with an arbitrary velocity profile is obtained. It is valid in the limit where the wavelength is large compared with the jet radius. Simple formulae for the acoustic pressure field due to convected point sources are also obtained. The results show (in a simple way) how the mean flow affects the radiation pattern from the sources. For convected lateral quadrupoles it causes the exponent of the Doppler factor multiplying the far-field pressure signal to be increased from the value of 3 used by Lighthill to 5.

Description: A new approach to seeing in the dark is described which is based on the principles of nonlinear optics employing a crystal such as lithium iodate. A nonlinear optical device capable of producing photons at higher frequencies from lower-frequency incident light is shown to upconvert infrared light directly into visible light. The major advantages of the infrared upconversion process is that it permits the infrared signal to be detected by photon-counting devices presently available for the visible spectral region, and that it can provide sensitivity to infrared radiation without the need for cryogenic cooling of the detector used. Early works on infrared upconversion are reviewed. The development of applications is discussed as to astronomical spectroscopy and infrared image upconversion involving either angular or positional resolution elements. The demonstration of infrared upconversion in rectangular waveguides of single-crystal GaAs by Anderson et al. (1971) indicates future possibilities in upconversion by the use of integrated optics devices.

Description: A tunable, Dicke-switched, infrared heterodyne radiometer (IHR) has been designed, fabricated, tested, and used to observe solar radiation and determine the atmospheric transmissivity in the 9-11-micron spectral band. The IHR provides a spectral resolution of 0.0067 reciprocal cm, a minimum detectable power level of 2.9 times ten to the minus twenty-third power W/Hz, and a temperature resolution of less than 1 K for a source temperature of 1000 K, an IF predetection bandwidth of 100 MHz, and an integration time of 30 s. Detailed design equations and measured IHR performance are presented. The IHR was used to make solar and atmospheric transmission measurements, and a vertical-path atmospheric attenuation of 2.3 dB has been established under favorable weather conditions. The attenuation of solar radiation due to cloud cover and haze has also been investigated.

Description: The 7.3 kg cameras for the 1976 Viking Mars expedition feature an array of 12 silicon photodiodes, including six spectral bands for color and near-infrared imaging with an angular resolution of 0.12 deg and four focus steps for broadband imaging, with an improved angular resolution of 0.04 deg. The field of view in elevation ranges from 40 deg above to 60 deg below the horizon, and in azimuth ranges to 342.5 deg. The cameras are mounted 0.8 m apart to provide a stereo view of the area accessible to a surface sampler for biological and chemical investigations. The scanning rates are synchronized to the lander data transmission rates of 16000 bits per sec to the Viking orbiters as relay stations and 250 bits per sec directly to earth. However, image data can also be stored on a lander tape recorder. About 10 million bits of image data will be transmitted during most days of the 60-day-long mission planned for each lander.

Description: The high field fluxgate magnetometer experiment flown aboard the Pioneer XI spacecraft is described. This extremely simple instrument was used to extend the spacecraft's upper-limit measurement capability by approximately an order of magnitude (from 0.14 mT to 1.00 mT) with minimum power and volume requirements. This magnetometer was designed to complement the low-field measurements provided by a helium vector magnetometer and utilizes magnetic ring core sensors with biaxial orthogonal sense coils. The instrument is a single-range, triaxial-fluxgate magnetometer capable of measuring fields of up to 1 mT along each orthogonal axis, with a maximum resolution of 1 microT.

Description: The effects of the grid transparency and finite collector size on the values of thermal ion density and temperature determined by the standard RPA (retarding potential analyzer) analysis method are investigated. The current-voltage curves calculated for varying RPA parameters and a given ion mass, temperature, and density are analyzed by the standard RPA method. It is found that only small errors in temperature and density are introduced for an RPA with typical dimensions, and that even when the density error is substantial for nontypical dimensions, the temperature error remains minimum.

Description: The phase correction for a Michelson interferometer with misaligned mirrors in converging light is shown to give rise to a quadratic phase shift. In general, the calculation of a spectrum from the measured interferogram needs phase correction. Phase corrections have been well worked out for the cases of a linear phase shift and a phase that is slowly varying. The standard procedures for correcting calculated spectra need to be modified, however, to remove any phase errors resulting from misaligned mirrors.

Description: The present investigation is an analysis of the radiation from the chemical nonequilibrium region in the shock layer about a vehicle during Venus entry. The radiation and the flow were assumed to be uncoupled. An inviscid, nonequilibrium flowfield was calculated and an effective electronic temperature was determined for the predominant radiating species. Species concentrations and electronic temperature were then input into a radiation transport code to calculate heating rates. The present results confirm earlier investigations which indicate that the radiation should be calculated using electronic temperatures for the radiating species. These temperatures are not related in a simple way to the local translational temperature. For the described mission, the nonequilibrium radiative heating rate is approximately twice the corresponding equilibrium value at peak heating.

Description: This paper describes the design and performance of a set of cosmic-ray particle experiments for the Pioneer 10/11 and Helios A/B space missions. These experiments had to be very light-weight, low-power and electronically sophisticated in order to meet the spacecraft and scientific requirements. Both sets of missions use several solid-state detector telescopes to measure protons from 100 KeV to 800 MeV and heavier ions up to Neon at 200 MeV per nucleon. Good performance is required for 7-8 years, and the system must tolerate large vibration loads and ionizing radiation doses up to 500,000 rads.

Description: Experimental cryogenic gyroscope drift data, discussing Fourier analysis and mathematical model

Description: Reynolds number dependence of near wake temperature of reentering probes and spacecraft determined using Apollo model temperature surveys for stagnation pressures

Description: Ablation patterns on cones having laminar and turbulent flows from ballistic range boundary layer transition studies using ablative models

Description: Angle of attack effect on laminar boundary layer transition on slender cone in contoured nozzle of helium tunnel, discussing Reynolds and Mach numbers effect

Description: Thin aluminum foil placed in magnetized plasma stream studied for lift drag ratio, noting magnetic field position influence on increase or decrease

Description: Effects of fixture stress vibration on mounted accelerometer signal

Description: Expansion of EV /exposure value/ system, deriving equations relating photographic factors for basic and flash photography

Description: Thin Ge wafers nondestructive thickness measurement by IR abborption measurement system using monochromatic He-Ne laser source

Description: High resolution scanning confocal interferometer illumination requirements from quasi-paraxial ray tracing calculation, considering additional reflections effect

Description: Double beam photoelectric filter photometer for simultaneous measurements of two astronomical objects, noting variable atmospheric extinction errors reduction

Description: VLF phenomena at 3.2, 9.6 and 16 kHz above ionosphere, using loop antenna on Ariel 3 satellite

Description: Temperature measurement errors due to negative magnetoresistance in carbon resistance thermometers, indicating correction procedure where magnetic field is involved

Description: Boundary layer transition point on forward portion of blunt Apollo type entry capsule model measured in high Reynolds number wind tunnel

Description: Root mean square time delay error with respect to playback time and autocorrelation function of tape recorded sine wave for studying jitter spectra

Description: Flow field of impulsively started circular cylinder, noting drag due to nonlinear convection

Description: Direct reading instrument using four point probe and two analog computing circuits for Si and Ge resistivity measurements

Description: Polarization adjustment instrumentation for rocket propagation experiment in lower ionosphere

Description: Single photon counting astronomical spectrophotometer to take advantage of increased information rate obtainable

Description: Automatic pressure transducer calibration systems

Description: Rotating spectral and spatial sound pressure distribution in propeller duct calculated on basis of propulsion quantities, noting effect of tip clearance

Description: Aerospace sensor systems, discussing adaptive multimode sensors and multispectral sensing, electronic recognition of image components, laser radar and Raman scattering technique

Description: Intense far UV atomic line sources obtained by microwave excitation of various gas mixtures in He with aid of flow lamps

Description: AC technique using lock-in power amplifier SNR for measuring galvanomagnetic and Shubnikov-de Haas effects, noting error reduction

Description: Plastic backing films removal from carbon electron microscope replicas by maintaining specimens in horizontal position

Description: Scanned laser beam display techniques based on cathode ray tube technology, noting flying spot scanner and beam deflection

Description: Radome material insertion loss measurement by radiometric method noting error analysis

Description: X Ray fluorescence of rock samples as applied to geological problems, noting standard deviations for element distribution

Description: Rapid scanning Fabry-Perot spectrometers, considering time resolution, wavelength resolution, wavelength interval size, aperture diameter and limitations of mechanical components

Description: A method is described in which thermal diffusivity measurements can be made on particulate materials using the identical instrumentation as described in previous papers for measuring thermal conductivity. The measurements for the two properties can be made simultaneously, thus eliminating the changes in conditions when they are made separately. This system has particular application for studies of simulated lunar, planetary, or asteroidal surfaces in which laboratory measurements can be correlated with astronomical observations of thermal inertia. A representative set of data is shown which gives thermal diffusivity and thermal conductivity measurements on a particulate basalt in which the values for each temperature were taken simultaneously. A value for specific heat is calculated for measurements taken at each temperature.

Description: A review is presented of progress in attaining technical objectives in three areas of semiautomatic airfoil development: software, hardware, and applications. Software objectives seek improved mathematical models and computer codes for flow analysis and design optimization for a variety of conditions. The 17-step iterative computer model used in designing the GA (W)-1 airfoil is effective but not yet fully automated; with present methods only single-point computer optimization is possible. Hardware objectives calling for improvement in test facilities and techniques are met in part by the introduction of the Langley (F-3C) wind tunnel for independent evaluation of transonic Mach number and Reynolds effects up to 12-16 million, and by a two-dimensional test section for the Langley 1/3 transonic cryogenic tunnel which will extend the Reynolds number to 50 million. The current status of low-speed, thin, and rotorcraft airfoil development programs is discussed.

Description: A closed-loop control law is developed for a dual-spin satellite control system which utilizes the interaction of the geomagnetic field with the satellite dipole parallel to the spin axis. The control law consists of the linear combination of the pitch axis component of the rate of change of the geomagnetic field and the product of the roll angle and roll axis component of the geomagnetic field. Application of the method of multiple time scales yields approximate solutions for the feedback gains in terms of the system parameters. Approximate solutions are also obtained for the response of the system to disturbance torques. A comparison of the approximate solutions and numerical solutions obtained by numerical integration of the exact equations of motion is then given.

Description: An apparatus is described which is used for the controlled production, characterization, and study of dissociated gases in a microwave discharge at elevated temperatures. A unique feature is the ability to produce and study a microwave discharge plasma in the heated zone. This allows elevated temperature reactions to be studied in high concentrations of dissociated gases. Further, the system permits weight change measurements of specimens in the plasma, thus facilitating reaction rate determinations. Included is a description of a cavity for use on a 50-mm diameter cylindrical reactor. The effects of flow rate, pressure, temperature, power, metal sample, and sampling position on dissociation percentage of oxygen in the apparatus are described as well as a technique for sample temperature measurements in the plasma which permits determination of high temperature recombination coefficients and reaction rates.

Description: The degradation of a hologram caused by object motion can be utilized to measure the rate of change of the length of an object beam. A rectangular shaped laser pulse is ordinarily used to illuminate the object in such an investigation. The velocity fringes obtained are considered in the calculation. There are no velocity fringes for Gaussian shaped pulses or for the pulses produced by a Q-switched ruby laser. It is shown with the aid of a mathematical analysis that a pulse of oscillating intensity or a pulse train will yield velocity fringes regardless of the shape of an individual pulse.

Description: An antenna was developed for the remote microwave measurement of ocean surface temperature during a flight test in a C54 aircraft. The basic antenna is a conical dual-mode horn similar to the dual-mode horn described by Potter (1963). The pertinent internal dimensions of the horn are given. The measured E and H plane patterns for the linearly polarized horn for a range of frequencies are shown in a graph.

Description: On December 3, 1974, Pioneer 11 passed the planet Jupiter at a distance of 42,000 km. The spacecraft is now headed for an encounter with the planet Saturn in September 1979. The prime scientific objectives of the Pioneer 10 and Pioneer 11 missions are discussed along with the spacecraft payload, aspects of spacecraft design, the spacecraft power supply, and details regarding the spacecraft trajectory during the approach to Jupiter.

Description: The relative importance of solar and trapped proton fluxes in the consideration of shielding requirements for geocentric space missions is analyzed. Using models of these particles, their fluences encountered by spacecraft in circular orbits are computed as functions of orbital altitude and inclination, mission duration, threshold energy (10 to 100 MeV), and risk factor (for solar protons only), and ratios of solar-to-trapped fluences are derived. It is shown that solar protons predominate for low-altitude polar and very high-altitude missions, while trapped protons predominate for missions at low and medium altitudes and low inclinations. It is recommended that if the ratio of solar-to-trapped protons falls between 0.1 and 10, both fluences should be considered in planning shielding systems.

Description: Conditions are predicted under which limit cycles may be caused by the friction torque of the control moment gyroscope (CMG) output gimbal used in the Large Space Telescope (LST). The parameter plane analysis technique is described, and three separate models of the CMG output friction nonlinearity are used in three separate analyses. The results suggest that the Dahl model (included in model 3) is the best available friction model for use in dynamic analysis. The analysis and analog simulation indicate the absence of limit cycle behavior due to the CMG output gimbal friction nonlinearity for presently estimated LST numerical parameters and the occurrence of one stable and one unstable limit cycle if substantially larger numerical values are allowed for the CMG gimbal pivot friction parameter and/or the running friction torque.

Description: The electron collecting efficiency of a cylindrical mirror energy analyzer incorporating retardation of the electrons prior to analysis has been determined over the range 0 to 30 eV by two methods. The first method requires the use of a vacuum ultraviolet monochromator to produce monoenergetic electrons of different energies; the second method involves measuring the energy-brightness relationship of the retarding optics and should be applicable to any deflection analyzer with pre-retarding optics. The results of the two methods are compared and the limitations of the latter method are discussed.

Description: Ambient electron concentrations derived from observations with the Radio Astronomy Explorer 1 antenna capacitance probe have been compared with upper hybrid resonance measurements from the same spacecraft. From this comparison an empirical correction factor for the capacitance probe measurements has been derived. The differences between the two types of measurements is attributed to sheath effects.

Description: The feasibility of using W41 filter media on a routine TSP high-volume monitoring network was determined by comparison with glass fiber (GF) filtering. Results indicate that suspended particulate samples from GF filters averaged slightly, but not significantly, higher than those from Whatman-41 filters. Some extra handling procedures were required to avoid errors due to the hygroscopic nature of W41 filters; these added procedures are not overly burdensome, however, and they allow the performance of analytical work, thus extending the capabilities of high-volume sampling. It was demonstrated that W41 filters are practical for air quality monitoring and elemental analysis in environments similar to Cleveland's.

Description: It is pointed out that the first successful infrared heterodyne spectrometer featuring semituneable semiconductor diode lasers was constructed and used near 8.5 micrometers to make laboratory measurements of line profiles in nitrous oxide and to detect thermal emission from Mars and from the moon. Questions of instrument design are discussed along with the significance of the results obtained in the investigation.

Description: Two new methods are described to measure velocities and angles of incidence of charged cosmic dust particles with precisions of about 1% and 1 deg, respectively. Both methods employ four one-dimensional position-sensitive detectors in series. The first method utilizes a charge-dividing technique while the second utilizes a time-of-flight technique for determining the position of a particle inside the instrument. The velocity vectors are measured although mechanical interaction between the particle and the instrument is completely avoided. Applications to cosmic dust composition and collection experiments are discussed. The range of radii of measurable particles is from about 0.01 to 100 microns at velocities from 1 to 80 km/sec.

Description: Two designs of plastic scintillation counters with an area of 2 sq m scanned in each case by a single photomultiplier of the FEU-49 type are described. The radial dependence of their light collection at the place of the path of the detected particle does not exceed 10% while the half width of the differential distribution of the pulse amplitudes from nonfiltered cosmic radiation at sea level is 90 to 95%, and 65%, the plastic thickness being 5 cm and 10 cm, respectively. The temperature coefficient of the counter is 0.32% per 1 C.

Description: Two types of formulas were obtained for (- dE/dx) and the number of collisions per unit of path length (dN/dx) = const, which depend on W sub m, with due account of the polarization effect of the medium.

Description: In 1964 a spark calorimeter was installed at the NOR-Amberd Station (2000 m above sea level). The advantages of this calorimeter over the ionization calorimeter are illustrated.

Description: A telescope consisting of three spark chambers and two control scintillation counters has been designed and is used for investigating the composition of the cosmic ray electron component within the range of energies from 1.0 to 10.0 BeV by the EN assymetry method. The geometrical factor of the telescope is approximately 20 sq cm ster. Discharges are recorded in the chambers on a photo film. The telescope is oriented to the azimuth with an accuracy of + or - 3 deg.

Description: The report describes two designs are reported of gas threshold Cerenkov counters for recording electrons of primary cosmic rays without recording protons. Also presented are design and technological measures which ensure maximum light collection of the Cerenkov radiation originating on the photocathode of the photomultiplier inside the radiator. The dependence of the reflection factor on the length of the light wave for different coatings is shown as well as for the throughput of the different optical materials employed. A range of methods for determining the efficiency of the counters during the recording of cosmic ray nucons and ways of increasing it further are given.

Description: The feasibility is examined of increasing the effectiveness of the scintillation and Cerenkov counters through improving light collection of the recorded radiation on the photoelectric cathode of the photomultiplier. An example of how to select a detector of the directional plexiglas Cerenkov counter is given. Also presented are experimentally obtained amplitude distributions during the recording of cosmic ray muons. The necessity to obtain agreement between the characteristic spectrum of the photocathode of the photomultiplier and the spectrum of the recorded radiation is stressed.

Description: A system for the recording and processing of telescope data is considered for measurements of EW asymmetry. The information is recorded by 45 channels on a continuously moving 35-mm film. The dead time of the recorder is about 0.1 sec. A sorting electronic circuit is used to reduce the errors when the statistical time distribution of the pulses is recorded. The recorded information is read out by means of photoresistors. The phototransmitter signals are fed either to the mechanical recorder unit for preliminary processing, or to a logical circuit which controls the operation of the punching device. The punched tape is processed by an electronic computer.

Description: An ionization calorimeter is described with a system of proportional counters which are used to determine the charge of the particles incident to the calorimeter and to estimate the number of the secondary charged particles.

Description: Large neutron counters designed for the neutron supermonitor with an area of about 20 sq m are reported. Statistical accuracy of the counters is 0.1% per 2 hours. Dimensions: length--2 m; diameter--150 mm; pressure--200 mm Hg. The counters are filled with BF3 gas containing over 80% of B-10.

Description: Developments in spacecraft technology are discussed with emphasis on the Explorer satellite program. The subjects considered include the following: (1) nutational behavior of the Explorer-45 satellite, (2) panoramic sensor development, (3) onboard camera signal processor for Explorer satellites, and (4) microcircuit development. Information on the zero gravity testing of heat pipes is included. Procedures for cleaning heat treated aluminum heat pipes are explained. The development of a five-year magnetic tape, an accurate incremental angular encoder, and a blood freezing apparatus for leukemia research are also discussed.

Description: Reynolds number, viscosity and atom concentration in hypervelocity nozzles measured using stagnation point heat transfer

Description: High speed selective recording system /SRS/ for data acquisition without computer, noting transistorized printed circuit logic modules

Description: P-i-n photodiodes incident quantum efficiency and apparent noise input power measurements, considering astronomical photometry applications

Description: Photometric properties of lunar surface target areas from high resolution TV pictures received from Surveyor 1 spacecraft

Description: Error computation in radiosonde and rocketsonde atmospheric temperature sensors by using thermistors of different emissivities

Description: Similarity transformation and perturbation solution for laminar two dimensional incompressible jet flow over curved surface of small curvature

Description: Industrial demands for highly motivated and competent technical personnel to carry forward with the technological goals of the US has posed a significant challenge to graduating engineers. While curricula has improved and diversified over time to meet these industry demands, relevant industry experience is not always available to undergraduates. The microsatellite development program at San Jose State University (SJSU) has allowed an entire undergraduate senior class to utilize a broad range of training and education to refine their engineering skills, bringing them closer to becoming engineering professionals. Close interaction with industry mentors and manufacturers on a real world project provides a significant advantage to educators and students alike. With support from companies and government agencies, the students have designed and manufactured a microsatellite, designed to be launched into a low Earth orbit. This satellite will gather telemetry for characterizing the state of the spacecraft. This will enable the students to have a physical check on their predicted value of spacecraft subsystem performance. Additional experiments will also be undertaken during the two year lifetime, including micro-meteorite impact sensing and capturing digital color images of the Earth. This paper will detail the process whereby students designed, prototype and manufactured a small satellite in a large team environment, along with the experiments that will be performed on board. With the project's limited funds, it needed the support of many industry companies to help with technical issues and hardware acquisition. Among the many supporting companies, NASA's space shuttle small payloads program could be used for an affordable launch vehicle for the student project. The paper address these collaborations between the student project and industry support, as well as explaining the benefits to both. The paper draws conclusion on how these types of student projects can be used by industry as a feasible resource for developing small platforms for space based experiments, as well as increasing the practical experience and engineering knowledge of graduating students. These benefits to industry and universities, can lead to a close working relationship between the two. These types of projects can facilitate the development of low-cost space rated parts to be used by the industry and university projects. It can also help with the understanding and use of acceptable risk non-space rated parts reducing the cost of the spacecraft. This will lead to the development of low cost platforms for space based experiments, providing research companies an inexpensive, long duration platform to conduct their in-space experiments, while better preparing engineering undergraduates for their transition into the work force.

Description: A prototype of the Josephson-effect spectrum analyzer developed for the millimeter wave band is described. The measurement results for spectra obtained in the frequency band from 50 to 250 GHz are presented.

Description: This summary describes the spatial, spectral, and radiometric calibration of Thermal Infrared Multispectral Scanner (TIMS) performed at the Jet Propulsion Laboratory (JPL) Thermal Infrared Calibration Facility (TIRCAL) between May and August, 1994. The 1994 calibration of TIMS was the first to make use of the new EXABYTE (8mm helical-scan tape) recording system. With the new recorder, the TIMS data tapes may be read directly on any computer system that has an EXABYTE tape drive. We analyzed the calibration data sets using image processing procedures written in Interactive Data Language.

Description: This summary describes the 9 March 1994 Thermal Infrared Multispectral Scanner (TIMS) airborne calibration experiment conducted at Castaic Lake, California. This experiment was a collaborative effort between the TIMS and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) science teams at the Jet Propulsion Laboratory (JPL). TIMS was flown on the NASA/Ames Research Center C130 with the new retractable air fence installed in the TIMS instrument bay. The purpose of this experiment was to determine if the fence would reduce the air turbulence in the TIMS instrument bay, thereby reducing the errors in calibration caused by wind-blast cooling of the blackbody reference sources internal to TIMS. Previous experiments have indicated that the wind blast effect could cause TIMS to over-estimate surface temperatures by more than 10 C. We have examined the TIMS data from twelve lines flown over Castaic Lake. Four of the lines were flown at an altitude of approximately 2.5 km (MSL), four at an altitude of approximately 6.7 km, and four at approximately 8.3 km. At each altitude there were flights with northern and southern headings, with the aircraft level and at a positive pitch (nose-up attitude). The suite of twelve flights was designed to subject the TIMS/air fence system to different wind conditions and air temperatures. The TIMS flights were supported by a ground-truth team, who measured lake surface temperatures from a boat, and an atmosphere characterization team, who launched an airsonde and measured solar irradiance with a Reagan Sun Photometer. The Reagan measurements were used to construct a time-series of estimates of the total abundance of water vapor in the atmospheric column. These estimates were used to constrain modifications of the airsonde water vapor profile measurements made when processing the TIMS data with a customized version of the MODTRAN radiative transfer code.

Description: The sedimentary geology of the western Grand Canyon consists of gently northeast dipping sandstones, shales, and carbonates. However, due to facies changes within the units, the geomorphology varies from that seen by visitors at the National Park Headquarters. There, the cliff and slope expression of the rocks is replaced in the west by a series of mesas, ridges, and horizontal platforms. The largest of these occurs on the Esplanade Sandstone within the Supai Formation. The Esplanade is formed by slope retreat of the overlying units and resistance to erosion by the underlying limestones. It is onto this platform that the lavas of the Uinkaret Plateau were emplaced. The Uinkaret lava field lies 120 km south of St. George, Utah and is tectonically defined by two major normal faults -- the Hurricane to the west and the Toroweap to the east. The purpose of this investigation was to collect visible, near and thermal infrared data at different periods of the day and year. It is expected that these data will provide the ability to retrieve water temperatures; monitor sediment loads; map and examine any changes in the near shore vegetation communities and understand some of the intricacies of the geology. This paper will serve, to some degree, as a progress report on the Grand Canyon study, since only a fraction of the data has been received and processed thus far. Data from the Thermal Infrared Multispectral Scanner (TIMS) and the Landsat Thematic Mapper simulator (NS001) were acquired simultaneously on April 4, 1994. A second data acquisition occurred on August 27, 1994. Initial analysis of the TIMS data indicates a remarkably noise-free data set with minimal atmospheric attenuation. environments is evident.

Description: The Jet Propulsion Laboratory (JPL) Field Emission Spectrometer (FES) was built by Designs and Prototypes based on a set of functional requirements supplied by JPL. The instrument has a spectral resolution of 6 wavenumbers (wn) and can acquire spectra from either the Mid Infrared (3-5 mu m) or the Thermal Infrared (8-12 pm) depending on whether the InSb or HgCdTe detector is installed respectively. The instrument consists of an optical head system unit and battery. The optical head which is tripod mounted includes the interferometer and detector dewar assembly. Wavelength calibration of the interferometer is achieved using a Helium-Neon laser diode. The dewar needs replenishing with liquid Nitrogen approximately every four hours. The system unit includes the controls for operation and the computer used for acquiring viewing and processing spectra. Radiometric calibration is achieved with an external temperature-controlled blackbody that mounts on the fore-optics of the instrument. The blackbody can be set at 5 C increments between 10 and 55 C. The instrument is compact and weighs about 33 kg. Both the wavelength calibration and radiometric calibration of the instrument have been evaluated. The wavelength calibration was checked by comparison of the position of water features in a spectrum of the sky with their position in the output from a high resolution atmospheric model. The results indicatethat the features in the sky spectrum are within 6-8 wn of their position ill the model spectrum. The radiometric calibration was checked by first calibrating the instrument using the external blackbody supplied with the instrument and then measuring the radiance from another external blackbody at a series of temperatures. The temperatures of these radiance spectra were then recovered by inventing Planck's law and the recovered temperatures compared lo the measured blackbody temperature. These results indicate that radiometric calibration is good to 0.5 C over the range of temperatures 10 to 55 C. The results also indicate that the instrument drifts slowly over time and should be recalibrated every 20 to 30 minutes in the field to ensure good radiometric fidelity. The instrument has now been extensively tested in the field in the United States and Australia. These in situ field measurements are being used to validate emissivity spectra recovered from the Thermal Infrared Multispectral Scanner (TIMS) and also the Australian CO2 Laser. The availability of in situ measurements is proving crucial to validation of the spectra derived from the airborne instruments since many natural surfaces cannot be easily transported back to the laboratory.

Description: AVIRIS is a NASA-sponsored Earth-remote-sensing imaging spectrometer designed, built and operated by the Jet Propulsion Laboratory (JPL). While AVIRIS has been operational since 1989, major improvements have been completed in most of the sensor subsystems during the winter maintenance cycles. As a consequence of these efforts, the capabilities of AVIRIS to reliably acquire and deliver consistently high quality, calibrated imaging spectrometer data continue to improve annually, significantly over those in 1989. Improvements to AVIRIS prior to 1994 have been described previously. This paper details recent and planned improvements to AVIRIS in the sensor task.

Description: This paper serves as a brief overview of the AVIRIS instrument (Airborne Visible/Infrared Imaging Spectrometer). The AVIRIS sensor collects data that will be used for quantitative characterization of the Earth's surface and atmosphere from geometrically coherent spectroradiometric measurements. This data can be applied to studies in the fields of oceanography, environmental science, snow hydrology, geology, volcanology, soil and land management, atmospheric and aerosol studies, agriculture, and limnology. Applications under development include the assessment and monitoring of environmental hazards such as toxic waste, oil spills, and land/air/water pollution. Mission planning and flight operations are discussed, and recommendations are given regarding the deployment of ground truth experiments.

Description: The AVIRIS sensor must be calibrated at the time it measures spectra from the ER-2 airborne platform in order to achieve research and application objectives that are both quantitative and physically based. However, the operational environment inside the Q-bay of the ER-2 at 20 km altitude differs from that in the AVIRIS laboratory with respect to temperature, pressure, vibration, and high-frequency electromagnetic fields. Experiments at surface calibration targets are used in each flight season to confirm the accuracy of AVIRIS in-flight radiometric calibrations. For these experiments, the MODTRAN radiative transfer code is constrained by using in situ measurements to independently predict the upwelling spectral radiance arriving at AVIRIS for a specific calibration target. AVIRIS calibration is validated in flight by comparing the MODTRAN-predicted radiance to the laboratory-calibrated radiance measured by the AVIRIS sensor for the same time over the calibration target. We present radiometric calibration results for the AVIRIS in-flight calibration experiment held at the beginning of the 1994 flight season.