ALBERT

Description: Large-eddy simulations are performed using wall-resolved mesh for a Mach 2.29 impinging shock wave/boundary-layer interaction. Flow conditions are based on an experiment and therefore entire span was simulated, including the two sidewalls. Mean flow comparison with the experimental data showed that the predicted interaction length was larger in the simulation. Time-series analysis of a rake of pressure signals immediately downstream of the mean reflected shock position showed a peak in weighted power spectral density occurred about St(sub Lint) = 0.01, owing to a larger interaction length. Budgets of Reynolds-stress transport calculated across the span and along the corner bisector showed high degree of anisotropy. Merging of the secondary flows and separation along the corner gave rise to unstable counter-rotating vortices, which straddle the corner and grow in size. This also leads to a development of new behavior in the viscous sublayer along the corner bisector, where the pressure strain and molecular diffusion mechanisms become prominent.

Description: Large-eddy simulations are performed using wall-resolved mesh for a Mach 2.29 impinging shock wave/boundary-layer interaction. Flow conditions are based on an experiment and therefore entire span was simulated, including the two sidewalls. Mean flow comparison with the experimental data showed that the interaction was larger in the simulation. Time-series analysis of a rake of pressure probes immediately downstream of the mean reflected shock position showed a peak in weighted power spectral density occurred about $St_{Lint}=0.01$, owing to a larger interaction length. Budgets of Reynolds-stress transport calculated across the span and along the corner bisector showed high degree of anisotropy. Merging of the secondary flows and separation along the corner gives rise to unstablecounter rotating vortices, which straddle the corner and grow in size. This also leads to a development of new behavior in the viscous sublayer along the corner bisector, where the pressure strain andmolecular diffusion mechanisms become prominent.

Description: Temperature-dependent data of a RUAG six-component block-type balance was analyzed to assess the accuracy of two load prediction methods for temperature-dependent balance data. The supplied data was prepared for the analysis by splitting it into calibration and check load data subsets. The first calibration data subset was obtained at a temperature of 294 Kelvin. The second calibration data subset was obtained at a temperature of 315 Kelvin. A subset of 38 points was extracted from the second data set and used as check loads so that the accuracy of the two load prediction methods could be tested. First, the Iterative Method in combination with an extended independent and dependent variable set was used for the balance load prediction. This approach fits electrical outputs as a function of loads and the temperature and, afterwards, constructs a load iteration scheme from the regression coefficients so that loads can be predicted from outputs and the temperature during a wind tunnel test. The Non-Iterative Method was also used for the load prediction. This alternate method can more easily be implemented in a data system as loads are directly fitted as a function of electrical outputs and the temperature. Analysis results for the axial force are only discussed in the paper as similar results were obtained for the other five load components. Results for both methods clearly show that the cross-product term constructed from either a primary gage load or a primary gage output and the temperature explains the majority of the temperature-dependent part of the predicted balance load. This term models the temperature dependent nature of the gage sensitivity. Therefore, it is recommended to apply primary gage loadings at different temperatures during a balance calibration whenever temperature effects need to be described. These loadings will contain information about the temperature-dependent nature of the gage sensitivities that can be quantified by related cross-product terms in regression models of the data.

Description: No abstract available

Description: No abstract available

Description: No abstract available

Description: No abstract available

Description: An overview of NASA GRC and how it is advancing exploration of our solar system and beyond while maintaining global leadership in aeronautics.

Description: A guiding principle for conducting research in technology, science, and engineering, leading to innovation is based on our use of research methodology (both qualitative and qualitative). A brief review of research methodology will be presented with an overview of NASA process in developing aeronautics technologies and other things to consider in research including what is innovation.

Description: A quantitative global skin-friction measurement technique is proposed. An oil-film is doped with a luminescent molecule and thereby made to fluoresce in order to resolve oil-film thickness, and Particle Image Surface Flow Visualization is used to resolve the velocity field of the surface of the oil-film. Skin-friction is then calculated at location x as (x )xh, where x is the displacement of the surface of the oil-film and is the dynamic viscosity of the oil. The data collection procedure and data analysis procedures are explained, and preliminary experimental skin-friction results for flow over the wing of the CRM are presented.

Description: As Unmanned Aircraft Systems (UAS) make their way to mainstream aviation operations within the National Airspace System (NAS), research efforts are underway to develop a safe and effective environment for their integration into the NAS. Detect and Avoid (DAA) systems are required to account for the lack of "eyes in the sky" due to having no human on-board the aircraft. The current NAS relies on pilot's vigilance and judgement to remain Well Clear (CFR 14 91.113) of other aircraft. RTCA SC-228 has defined DAA Well Clear (DAAWC) to provide a quantified Well Clear volume to allow systems to be designed and measured against. Extended research efforts have been conducted to understand and quantify system requirements needed to support a UAS pilot's ability to remain well clear of other aircraft. The efforts have included developing and testing sensor, algorithm, alerting, and display requirements. More recently, sensor uncertainty and uncertainty mitigation strategies have been evaluated. This paper discusses results and lessons learned from an End-to-End Verification and Validation (E2-V2) simulation study of a DAA system representative of RTCA SC-228's proposed Phase I DAA Minimum Operational Performance Standards (MOPS). NASA Langley Research Center (LaRC) was called upon to develop a system that evaluates a specific set of encounters, in a variety of geometries, with end-to-end DAA functionality including the use of sensor and tracker models, a sensor uncertainty mitigation model, DAA algorithmic guidance in both vertical and horizontal maneuvering, and a pilot model which maneuvers the ownship aircraft to remain well clear from intruder aircraft, having received collective input from the previous modules of the system. LaRC developed a functioning batch simulation and added a sensor/tracker model from the Federal Aviation Administration (FAA) William J. Hughes Technical Center, an in-house developed sensor uncertainty mitigation strategy, and implemented a pilot model similar to one from the Massachusetts Institute of Technology's Lincoln Laboratory (MIT/LL). The resulting simulation provides the following key parameters, among others, to evaluate the effectiveness of the MOPS DAA system: severity of loss of well clear (SLoWC), alert scoring, and number of increasing alerts (alert jitter). The technique, results, and lessons learned from a detailed examination of DAA system performance over specific test vectors and encounter cases during the simulation experiment will be presented in this paper.

Description: Vibration-based condition indicators continue to be developed for Health Usage Monitoring of rotorcraft gearboxes. Testing performed at NASA Glenn Research Center have shown correlations between specific condition indicators and specific types of gear wear. To speed up the detection and analysis of gear teeth, an image detection program based on the Viola-Jones algorithm was trained to automatically detect spiral bevel gear wear pitting. The detector was tested using a training set of gear wear pictures and a blind set of gear wear pictures. The detector accuracy for the training set was 75 percent while the accuracy for the blind set was 15 percent. Further improvements on the accuracy of the detector are required but preliminary results have shown its ability to automatically detect gear tooth wear. The trained detector would be used to quickly evaluate a set of gear or pinion pictures for pits, spalls, or abrasive wear. The results could then be used to correlate with vibration or oil debris data. In general, the program could be retrained to detect features of interest from pictures of a component taken over a period of time.

Description: Future urban mobility promises to deliver transformative impact across the value chain. Consequently, suppliers will face disruption in the form of new technologies, stakeholders and market dynamics. How can supply networks be optimized to meet capabilities that are yet unknown? This session will explore what business models and supply chain strategies can best deliver value for urban air transport and will address how to scale these networks at the pace of this rapidly evolving ecosystem.

Description: Turbulent flows have a large range of spatial and temporal scales which need to be resolved in order to obtain accurate predictions. Higher-order methods can provide greater efficiency for simulations requiring high spatial and temporal resolution, allowing for solutions with fewer degrees of freedom and lower computational cost than traditional second-order computational fluid dynamics (CFD) methods.1 Higher-order methods have been widely used for turbulent flows. However, the reduced numerical stabilization present in higher-order schemes implies that special care needs to be taken in the development of numerical methods to suppress nonlinear instabilities.26 In this work we present the development of a higher-order space-time discontinuous Galerkin method with a focus on the aspects of our numerical scheme required for ensuring nonlinear stability for turbulent simulations at high Reynolds numbers.

Description: Results are presented for four optimization benchmark problems posed by the AIAA Aerodynamic Design Optimization Discussion Group. The benchmarks are intended to exercise optimization frameworks on representative airfoil and wing design problems. All problems involve drag minimization subject to geometric and aerodynamic constraints. Our design approach involves two forms of adaptation. First, the shape parameterization is gradually and automatically enriched from an initially coarse search space. Second, adjoint solutions are used to drive adaptive mesh refinement to control discretization error. The error threshold is tailored so that the nest meshes, with the greatest accuracy, are used only when nearing the optimum. On the inviscid airfoil design problem, while reducing the drag by a factor of 10, we show how the combination of progressive parameterization and tiered discretization error control can dramatically accelerate the optimization. On the viscous airfoil design problem, we use inviscid analysis-driven optimization to reduce the total drag by a factor of two. Next, we improve the span efficiency factor of a wing by performing twist optimization. Finally, we optimize the Common Research Model wing, managing to hold drag roughly fixed, while targeting an initially-violated pitching moment constraint. Our approach aims to introduce greater complexity and accuracy only when necessary to improve the design, and also support a greater degree of automation.

Description: An overview of the NASA Advanced Air Transport Technology (AATT) Project and interest inboundary layer transition modeling for future aircraft and propulsion systems is presented.

Description: Uncertainties in early observations of potentially hazardous asteroids result in preliminary impact corridors that can stretch across large portions of the Earths surface. At this early stage of detection, the corridor width and potential for damage are typically estimated using techniques from nuclear weapons research. These estimates often employ spherical blast assumptions resulting in a constant width impact corridor. In actuality, however, the ground damage footprint of obliquely entering asteroids is generally roughly elliptical or butterfly shaped, with the major axis extending in the cross range direction and the minor axis aligned with ground-track of the meteoroid. Since actual ground footprints for oblique entries may have aspect ratios greater than two or three, the assumption of a circular blast may significantly underestimate the area of the impact swath and the at-risk population. This work develops an engineering model that can be used to quickly estimate the eccentricity of the ground footprint as a function of local impact parameters. This yields vastly improved local estimates of the corridor width and can significantly enhance the accuracy of risk analysis.

Description: ASA & Ames Introduction: Overview of NASA and Ames Research Activities, with a special focus on NASA Aeronautics activities. All materials are overview in nature and have been presented previously in open forums.

Description: NASA & Ames Introduction: Overview of NASA and Ames Research Activities, with a special focus on NASA Aeronautics activities. All materials are overview in nature and have been presented previously in open forums.

Description: This paper considers the control of coupled aeroelastic aircraft model with Variable Camber Continuous Trailing Edge Flap (VCCTEF) system. The relative motion between two adjacent flaps is constrained and this actuation constraint problem is converted into an output covariance constraint problem, and therefore can be formulated using linear matrix inequalities (LMIs). A set of LMI conditions is derived for the design of an observer-based dynamic output feedback controller for VCCTEF configured aeroelastic aircraft model. The proposed controller is then applied to the NASA Generic Transport Model (GTM) for simulation, and the results demonstrate the efficacy of the proposed approach.

Description: This PowerPoint presentation will discuss Aura's current spacecraft and instrument status, highlight any performance trends and impacts to operations, identify any operational changes and express concerns or potential process improvements. Reviewed by Eric Moyer, ESMO Deputy Project Manager.

Description: Computational simulations using structured overset grids with the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are presented for predicting oblique shock/plume interaction effects to near-field sonic boom signatures. Standard second-order accurate as well as higher-resolution numerical discretizations are utilized and compared in the study. The numerical approach is compared with supersonic wind-tunnel data for three cases. The cases include an empty wind-tunnel at the operating conditions, an isolated shockgenerating diamond wedge within the tunnel, and a nozzle with diamond wedge configuration at five different nozzle pressure ratios. Solution sensitivity to numerical discretization is analyzed. Favorable comparisons between the computational results and experimental data of near-field pressure signatures are obtained. A simple prediction method for plume induced shock deflection is developed and results are compared with the CFD data.

Description: The rising number of small unmanned aerial vehicles (UAVs) expected in the next decade will enable a new series of commercial, service, and military operations in low altitude airspace as well as above densely populated areas. These operations may include on-demand delivery, medical transportation services, law enforcement operations, traffic surveillance and many more. Such unprecedented scenarios create the need for robust, efficient ways to monitor the UAV state in time to guarantee safety and mitigate contingencies throughout the operations. This work proposes a generalized monitoring and prediction methodology that utilizes realtime measurements of an autonomous UAV following a series of way-points. Two different methods, based on sinusoidal acceleration profiles and high-order splines, are utilized to generate the predicted path. The monitoring approach includes dynamic trajectory re-planning in the event of unexpected detour or hovering of the UAV during flight. It can be further extended to different vehicle types, to quantify uncertainty affecting the state variables, e.g., aerodynamic and other environmental effects, and can also be implemented to prognosticate safety-critical metrics which depend on the estimated flight path and required thrust. The proposed framework is implemented on a simplified, scalable UAV modeling and control system traversing 3D trajectories. Results presented include examples of real-time predictions of the UAV trajectories during flight and a critical analysis of the proposed scenarios under uncertainty constraints.

Description: No abstract available

Description: Downwash and outwash characteristics of a model-scale tandem-rotor system in the presence of the ground were analyzed by identifying and understanding the physical mechanisms contributing to the observed flow field behavior. A building block approach was followed in simplifying the problem, separating the effects of the fuselage, effects of one rotor on the other, etc. Flow field velocities were acquired in a vertical plane at four aircraft azimuths of a small-scale tandem rotor system using the particle image velocimetry (PIV) technique for radial distances up to 4 times the rotor diameter. Results were compared against full-scale CH-47D measurements. Excellent correlation was found between the small- and full-scale mean flow fields (after appropriate normalization using rotor and wall jet parameters). Following the scalability analysis, the effect of rotor height on the outwash was also studied. Close to the aircraft, an increase in rotor height above ground decreased the outwash velocity at all aircraft azimuths. However, farther away, the longitudinal and lateral axes of the aircraft showed increasing and decreasing outwash velocities, respectively, with increasing rotor height. Measurements also indicated the presence of large-scale (of the size of the rotor height) shear-layer vortical structures along the ground that could be the source of low-frequency (approximately 1 Hz) flow variation observed in the full-scale measurements. Flow visualization studies and PIV measurements were also made on jets of different sizes to complement the observations made on rotors wherever possible. Baseline rotor measurements were made out-of-ground effect to understand the nature of inflow distribution for realistic rotor configurations and their modified characteristics in the presence of ground. Lastly, a feasibility study on applying high-fidelity CFD simulations for outwash study was conducted using Helios to model an isolated rotor configuration IGE at full-scale Reynolds number. The results were encouraging and demonstrated the practical challenges associated with predicting rotor outwash.

Description: This paper evaluates a thermodynamic ice crystal icing model that has been previously presented to describe the possible mechanisms of icing within the core of a turbofan jet engine. The model functions between two distinct ice accretions based on a surface energy balance: freeze-dominated icing and melt-dominated icing. Freeze-dominated icing occurs when liquid water (from melted ice crystals) freezes and accretes on a surface along with the existing ice of the impinging water and ice mass. This freeze-dominated icing is characterized as having strong adhesion to the surface. The amount of ice accretion is partially dictated by a freeze fraction, which is the fraction of impinging liquid water that freezes. Melt-dominated icing occurs as unmelted ice on a surface accumulates. This melt-dominated icing is characterized by weakly bonded surface adhesion. The amount of ice accumulation is partially dictated by a melt fraction, which is the fraction of impinging ice crystals that melts. Experimentally observed ice growth rates suggest that only a small fraction of the impinging ice remains on the surface, implying a mass loss mechanism such as splash, runback, bounce, or erosion. The fraction of mass loss must be determined in conjunction with the fraction of freezing liquid water or fraction of melting ice on an icing surface for a given ice growth rate. This mass loss parameter, however, along with the freeze fraction and melt fraction, are the only experimental parameters that are currently not measured directly. Using icing growth rates from ice crystal icing experiments, a methodology that has been previously proposed is used to determine these unknown parameters. This work takes ice accretion data from tests conducted by the National Aeronautics and Space Administration (NASA) at the Glenn Research Center in 2018 that examined the fundamental physics of ice crystal icing. This paper continues evaluation of the thermodynamic model from a previous effort, with additions to the model that account for sub-freezing temperatures that have been observed at the leading edge of the airfoil during icing. The predicted temperatures were generally in good agreement with measured temperatures. Other key findings include the total wet-bulb temperature being a good first order indicator of whether icing is freeze-dominated (sub-freezing values) or melt-dominated (above freezing). Maximum sticking efficiency values, the fraction of impinging mass that adheres to a surface, was calculated to be about 0.2, and retained this maximum value for a range of melt ratios (0.3 to 0.65 and possibly higher), which is defined as the ratio of liquid water content to total water content. Higher air velocities reduced the maximum sticking efficiency and shifted the icing regime to higher melt ratio values. Finally, the leading edge ice accretion angle was found to be related to ice growth (lower growth rates for smaller angles) and melt ratio (smaller melt ratios resulted in smaller angles, likely due to erosion effects).

Description: The Honeywell Uncertified Research Engine (HURE), a research version of a turbofan engine that never entered production, was tested in the NASA Propulsion System Laboratory (PSL), an altitude test facility at the NASA Glenn Research Center. The PSL is a facility that is equipped with water spray bars capable of producing an ice cloud consisting of ice particles, having a controlled particle diameter and concentration in the air flow. To develop the test matrix of the HURE, numerical analysis of flow and ice particle thermodynamics was performed on the compression system of the turbofan engine to predict operating conditions that could potentially result in a risk of ice accretion due to ice crystal ingestion. The goal of the test matrix was to have ice accrete in two regions of the compression system: region one, which consists of the fan-stator through the inlet guide vane (IGV), and region two which is the first stator within the high pressure compressor. The predictive analyses were performed with the mean line compressor flow modeling code (COMDES-MELT) which includes an ice particle model. The HURE engine was tested in PSL with the ice cloud over the range of operating conditions of altitude, ambient temperature, simulated flight Mach number, and fan speed with guidance from the analytical predictions. The engine was fitted with video cameras at strategic locations within the engine compression system flow path where ice was predicted to accrete, in order to visually confirm ice accretion when it occurred. In addition, traditional compressor instrumentation such as total pressure and temperature probes, static pressure taps, and metal temperature thermocouples were installed in targeted areas where the risk of ice accretion was expected. The current research focuses on the analysis of the data that was obtained after testing the HURE engine in PSL with ice crystal ingestion. The computational method (COMDES-MELT) was enhanced by computing key parameters through the fan- stator at multiple span wise locations, in order to increase the fidelity with the current mean-line method. The Icing Wedge static wet bulb temperature thresholds were applicable for determining the risk of ice accretion in the fan-stator, which is thought to be an adiabatic region. At some operating conditions near the splitter-lip region, other sources of heat (non-adiabatic walls) were suspected to be the cause of accretion, and the Icing Wedge was not applicable to predict accretion at that location. A simple order-of-magnitude heat transfer model was implemented into the COMDES-MELT code to estimate the wall temperature minimum and maximum thresholds that support ice accretion, as observed by video confirmation. The results from this model spanned the range of wall temperatures measured on a previous engine that experienced ice accretion at certain operating conditions.

Description: Any cluster of parachute systems is subject to effects on performance due to interactions between the parachutes. One such interaction is the twisting of a riser from one parachute around that of another. Due to friction and relative motion between the risers, it is possible for the tension in the riser near the attach point to be different from the tension in the riser towards the suspension lines or canopy. This could result in system failure due to larger than expected loading. The Orion Capsule Parachute Assembly System (CPAS) designed and executed a test to quantify the amplification of the load in a parachute riser due to twist, rocking rate and angle, cluster size, and canopy load. The design of the testing approach, test matrix, and hardware are discussed along with results and findings.

Description: The swirl distortion of a StreamVane (Trademark) was investigated in the NASA Glenn Research Center W8 test facility. The StreamVane (Trademark) was designed and generated by Virginia Tech based on CFD simulations and included a center body at the aerodynamic interface plane. The swirl pattern generated by the distortion was evaluated using a dense grid of 5-hole Pitot probe measurements captured using a rotating array of probes. Good agreement was found between the design intent and the results at 38.5 kg/s mass flow. The StreamVane (Trademark) swirl results were compared to clean facility flow at 5 inlet mass flows and found to be consistent. Additionally, the axial location of the StreamVane (Trademark) relative to the measurement plane was investigated to determine the impact on downstream total pressure loss generated by the vanes. The intent of this work was to assess the viability of using a StreamVane (Trademark) to generate a Type I or Type II distortion into a Boundary Layer Ingesting propulsor to assess its aerodynamic performance and aeromechanic response.

Description: The Honeywell Uncertified Research Engine (HURE), a research version of a turbofan engine that never entered production, was tested in the NASA Propulsion System Laboratory (PSL), an altitude test facility at the NASA Glenn Research Center. The PSL is a facility that is equipped with water spray bars capable of producing an ice cloud consisting of ice particles, having a controlled particle diameter and concentration in the air flow. To develop the test matrix of the HURE, numerical analysis of flow and ice particle thermodynamics was performed on the compression system of the turbofan engine to predict operating conditions that could potentially result in a risk of ice accretion due to ice crystal ingestion. The goal of the test matrix was to have ice accrete in two regions of the compression system: region one, which consists of the fan-stator through the inlet guide vane (IGV), and region two which is the first stator within the high pressure compressor. The predictive analyses were performed with the mean line compressor flow modeling code (COMDES-MELT) which includes an ice particle model. The HURE engine was tested in PSL with the ice cloud over the range of operating conditions of altitude, ambient temperature, simulated flight Mach number, and fan speed with guidance from the analytical predictions. The engine was fitted with video cameras at strategic locations within the engine compression system flow path where ice was predicted to accrete, in order to visually confirm ice accretion when it occurred. In addition, traditional compressor instrumentation such as total pressure and temperature probes, static pressure taps, and metal temperature thermocouples were installed in targeted areas where the risk of ice accretion was expected. The current research focuses on the analysis of the data that was obtained after testing the HURE engine in PSL with ice crystal ingestion. The computational method (COMDES-MELT) was enhanced by computing key parameters through the fan-stator at multiple span wise locations, in order to increase the fidelity with the current mean-line method. The Icing Wedge static wet bulb temperature thresholds were applicable for determining the risk of ice accretion in the fan-stator, which is thought to be an adiabatic region. At some operating conditions near the splitter-lip region, other sources of heat (non-adiabatic walls) were suspected to be the cause of accretion, and the Icing Wedge was not applicable to predict accretion at that location. A simple order-of-magnitude heat transfer model was implemented into the COMDES-MELT code to estimate the wall temperature minimum and maximum thresholds that support ice accretion, as observed by video confirmation. The results from this model spanned the range of wall temperatures measured on a previous engine that experienced ice accretion at certain operating conditions.

Description: This paper presents a new method for transonic pitching airfoils based on a RANS CFD study and the Theodorsen model of an oscillating pitching flat plate. This study quantifies the deviation of the lift coefficient predictions using CFD from that obtained using the Theodorsen model, which is based on the incompressible potential flow assumption. The present method corrects this theoretical model by modulating the Theodorsen functions by coefficient functions that depend on the reduced frequency and the Mach number. It is demonstrated that the modified theoretical model predicts lift coefficient in good agreement with the CFD results in the Mach number range from incompressible (M =0.2) to transonic (M =0.755) flow for a range of reduced frequencies typical of transonic flutter. The simulations are first validated by comparing pitching NACA0012 airfoil results with experimental results at transonic flight conditions, which establishes the requirements for a grid converged unsteady transonic solution. The hysteresis loop, Cl versus , attains a grid independent solution that compares well with experiment. The present correction method will guide the development of a new state space model for the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system and eventually a new transfer function that will be incorporated in a new aeroelastic framework leading to an appropriate transonic flutter model for use in the future aircraft systems in development under the NASA Advanced Air Transportation Technologies (AATT) project.

Description: No abstract available

Description: Performing impact risk assessment for the 2017 Planetary Defense Conference (PDC17) hypothetical impact exercise, to take place at the PDC17 conference, May 15-20, 2017. Impact scenarios and trajectories are developed and provided by NASA's Near Earth Objects Office at JPL (Paul Chodas). These results represent purely hypothetical impact scenarios, and do not reflect any known asteroid threat. Risk assessment was performed using the Probabilistic Asteroid Impact Risk (PAIR) model developed by the Asteroid Threat Assessment Project (ATAP) at NASA Ames Research Center. This presentation includes sample results that may be presented or used in discussions during the various stages of the impact exercisecenter dot Some cases represent alternate scenario options that may not be used during the actual impact exercise at the PDC17 conference. Updates to these initial assessments and/or additional scenario assessments may be performed throughout the impact exercise as different scenario options unfold.

Description: A study into the effects of altitude on an aircraft thermal Ice Protection System (IPS) performance has been conducted by the National Research Council Canada (NRC) in collaboration with the NASA Glenn Icing Branch. The study included tests of an airfoil model, with a heated-air IPS, installed in the NRCs Altitude Icing Wind Tunnel (AIWT) at altitude and ground level conditions.

Description: The NATO HFM-247 Working Group is creating a summary report of the group's activities on human-autonomy teaming. This chapter is a summary of our at NASA Ames work toward developing a framework for human-autonomy teaming (HAT) in aviation. The purpose of this project was to demonstrate and evaluate proposed tenets of HAT. The HAT features were derived from three tenets and were built into an automated recommender system on a ground station. These tenets include bi-directional communication, automation transparency, and operator directed interface. This study focused primarily on interactions with one piece of automation, the Autonomous Constrained Flight Planner (ACFP). The ACFP is designed to support rapid diversion decisions for commercial pilots in off-nominal situations. Much effort has gone into enhancing this tool not only in capability but also in transparency. In this study, participants used the ACFP at a ground station designed to aid dispatchers in a flight following role to reroute aircraft in situations such as inclement weather, system failures and medical emergencies. Participants performed this task both with HAT features enabled and without and provided feedback. We examined subjective and behavioral indicators of HAT collaborations using a proof-of-concept demonstration of HAT tenets. The data collected suggest potential advantages and disadvantages of HAT.

Description: A research team of U.S. Government agencies and engine manufacturers conducted an experiment to test volcanic-ash ingestion by a NASA owned engine in the same family as the PW 2000 that was donated by the U.S. Air Force. The experiment, called Vehicle Integrated Propulsions Research (VIPR) test, was conducted under the auspices of NASAs Convergent Aeronautics Solutions (CAS) Program and took place in summer of 2015 at Edwards AFB in California as an on-ground, on-wing test. The primary objectives of the volcanic ash test were to determine the effect on the engine of several hours of exposure to low to moderate ash concentrations and to evaluate the capability of engine health management technologies for detecting these effects. The target concentrations of volcanic ash tested were at 1 and 10 mgm3. A natural volcanic ash was used that is representative of distal ash clouds many 100s to 1000 km from a volcanic source. The glassy ash particles were expected to soften and become less viscous when exposed to the high temperatures of the combustion chamber, then stick to the nozzle guide vanes of the high-pressure turbine and this was observed. Numerous observations and measurements of the engines performance and degradation were made during the course of the experiment, including borescope inspections after each test run. The engine has been disassembled so that detailed inspections of the engine effects have been made. A summary of the test methodology and execution will be made along with results from the test. While not intended to be sufficient for rigorous certification of engine performance when ash is ingested, the experiment should provide useful information to aircraft manufacturers, airline operators, and military and civil regulators in their efforts to evaluate the range of risks that ash hazards pose to aviation.

Description: This paper presents a new method to design Robust Switching State-Feedback Gain-Scheduling (RSSFGS) controllers for Linear Parameter Varying (LPV) systems with uncertain scheduling parameters. The domain of scheduling parameters are divided into several overlapped subregions to undergo hysteresis switching among a family of simultaneously designed LPV controllers over the corresponding subregion with the guaranteed H-infinity performance. The synthesis conditions are given in terms of Parameterized Linear Matrix Inequalities that guarantee both stability and performance at each subregion and associated switching surfaces. The switching stability is ensured by descent parameter-dependent Lyapunov function on switching surfaces. By solving the optimization problem, RSSFGS controller can be obtained for each subregion. A numerical example is given to illustrate the effectiveness of the proposed approach over the non-switching controllers.

Description: Several multimodel ensemble methods are selected and further developed to improve the deterministic and probabilistic prediction skills of individual wake-vortex transport and decay models. The different multimodel ensemble methods are introduced, and their suitability for wake applications is demonstrated. The selected methods include direct ensemble averaging, Bayesian model averaging, and Monte Carlo simulation. The different methodologies are evaluated employing data from wake-vortex field measurement campaigns conducted in the United States and Germany.

Description: This paper summarizes the development of lean direct injection (LDI) combustor technology at, or in collaboration with, the NASA Glenn Research Center. These configurations differ mainly in fuel-air mixing strategy. The paper reviews the NOx performance and operability characteristics of multiple LDI configurations tested at NASA Glenn.

Description: This paper summarizes the development of lean direct injection (LDI) combustor technology at, or in collaboration with, the NASA Glenn Research Center. These configurations differ mainly in fuel-air mixing strategy. The paper reviews the NOx performance and operability characteristics of multiple LDI configurations tested at NASA Glenn.

Description: Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

Description: This work continues the analysis of data obtained during a 2017 NASA DGEN Aeropropulsion Research Turbofan (DART) core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). The DART is a cost-efficient testbed for the study of core-noise physics and mitigation. Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft-quadrant farfield, a single midfield microphone, and two infinite-tube-probe sensors for unsteady pressures at the core-nozzle exit. The data are here examined on an 1/3-octave basis as a first step in extending and improving core-noise prediction capability.

Description: Rotor wake dispersion in a low-speed, one and half stage axial compressor is investigated in detail with a Large Eddy Simulation (LES). The primary focus is to quantify the total pressure recovery due to wake stretching and the total pressure loss from the rotor wake interaction with the stator blade boundary layer. The relative magnitude of the aerodynamic loss due to these two effects is examined at several radial locations. The spacing between the rotor and the stator was varied from 29% to 112% of the rotor axial chord at the mid span to investigate the effects of rotor wake decay before entering the stator passage. The current analysis indicates that the efficiency through the compressor stage is increased about 0.5% when the spacing between the rotor and the stator is decreased from 112% to 29% of the rotor axial chord at mid-span. 22% of the efficiency gain from the narrower axial gap is due to the wake recovery and 63% is due to the stronger unsteady pressure field at the exit of the rotor due to stage interaction. Total pressure loss/recovery across the stator varies significantly in the radial direction for the current compressor, which has a much lower aspect ratio. The total pressure recovery due to wake stretching is larger than the total pressure loss due to the unsteady boundary layer development on the stator blade from 20% to 35% of the span from the hub for 29% spacing and from 35% to 55% of the span for 112% spacing. Above 50% of the span, rotor tip clearance flow affects wake dispersion and the overall wake recovery is less than expected.

Description: No abstract available

Description: This presentation provides an overview of the Aeronautics Research Mission Directorate and SBIRSTTR topics for ARMD's programs and project.

Description: Air-launch is defined as two or more air-vehicles joined and working together, that eventually separate in flight, and that have a combined performance greater than the sum of the individual parts. The use of the air-launch concept has taken many forms across civil, commercial, and military contexts throughout the history of aviation. Air-launch techniques have been applied for entertainment, movement of materiel and personnel, efficient execution of aeronautical research, increasing aircraft range, and enabling flexible and efficient launch of space vehicles. For each air-launch application identified in the paper, the motivation for that application is discussed.

Description: This paper examines the fundamentals of fuel-air mixing in a lean direct injection concept. Results are presented to investigate the effects of air swirler angle, element spacing, and center element offset on recirculation zone formation, flame stability and gaseous emissions.

Description: Air-launch is defined as two or more air-vehicles joined and working together, that eventually separate in flight, and that have a combined performance greater than the sum of the individual parts. The use of the air-launch concept has taken many forms across civil, commercial, and military contexts throughout the history of aviation. Air-launch techniques have been applied for entertainment, movement of materiel and personnel, efficient execution of aeronautical research, increasing aircraft range, and enabling flexible and efficient launch of space vehicles. For each air-launch application identified in the paper, the motivation for that application is discussed.

Description: NASA is seeking a new baseline aircraft model to assess the state-of-the-art technology for aircraft noise, emissions, and fuel/energy consumption as an update to a 2005 baseline. The process of modeling engine and airframe models as a system has historically required many iterations at NASA between the airframe and engine models. A new internal process presented in this paper contains a method that simultaneously calibrates an airframe and engine model to known data to create an aircraft system model. The work presented in this paper proposes a new framework in creating new aircraft models for future NASA research. This approach is presented as a general outline applicable to any chosen commercial aircraft. As an applied example, the B737 MAX 8 aircraft is chosen as the integrated engine and airframe model subjected to calibration. Initial results show a close match to available data but further refinement in the process is necessary for this ongoing work.

Description: The 9- by 15-Foot Low Speed Wind Tunnel (9x15 LSWT) at NASA Glenn Research Center was built in 1969 in the return leg of the 8- by 6-Foot Supersonic Wind Tunnel (8x6 SWT). The 8x6 SWT was completed in 1949 and acoustically treated to mitigate community noise issues in 1950. This treatment included the addition of a large muffler downstream of the 8x6 SWT test section and diffuser. The 9x15 LSWT was designed for performance testing of V/STOL aircraft models, but with the addition of the current acoustic treatment in 1986 the tunnel been used principally for acoustic and performance testing of aircraft propulsion systems. The present document describes the status of the acoustic upgrade as of early 2019.

Description: High speed rotorcraft transmissions are subject to load-independent power losses consisting of drag and pumping loss. Tightly conforming shrouds enclosing the transmission gears are often incorporated to reduce the drag component of the total load-independent losses. However, tightly conforming axial shrouding can result in an increase in the pumping loss component. Quantifying the pumping loss of shrouded gear transmissions has been the subject of many studies. This study presents a new approach for estimating pumping loss based on the concept of swept volume borrowed from the positive displacement pump and compressor industry. In this study, pumping loss of shrouded gear transmissions is considered to be related to the swept volume of the gear sets and the downstream flow resistance created by the shroud clearances. The drag loss and pumping loss of a spur gear pair have been determined through testing using the NASA Glenn Research Center Gear Windage Test Facility. The results from this testing have been compared to theoretical results using the formulations presented in this study. Good correlation exist between the test pumping power loss and the predicted pumping power loss for tightly conforming axial shroud configurations.

Description: An initial ice shape database has been created to document ice accretions on a 21-inch chord NACA 0012 airfoil model resulting from an exposure to a Supercooled Large Droplet (SLD) icing cloud with a bimodal droplet distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each accretion. The icing conditions used in the test matrix were based upon previously measured ice shapes on the same model to connect the current database to previously measured information. Ice shapes resulting from the bimodal distribution as well as from equivalent standard droplet distributions were obtained and compared. Results indicate that the ice shapes resulting from the bimodal droplet distributions had higher mass and volume values than their standard distribution equivalents as well as having icing limits that extended further back on the chord of the model.

Description: This presentation serves as an overview of test plans for an upcoming DGEN Aeropropulsion Research Turbofan (DART) test entry at the NASA GRC AeroAcoustic Propulsion Laboratory (AAPL). The test entry includes: (1)a fan intra-stage velocity field survey, which will be compared to a Computational Fluid Dynamics (CFD) survey of DART, (2) an exploratory noise study of DART with several objectives focused on measurement projection to the far-field, source identification improvements and development of a barrier wall for isolation of various sources, (3) advancement of core/combustor noise research on DART using more extensive engine-mounted instrumentation, and (4) high-temperature pressure sensor technology-readiness-level (TRL) advancement.

Description: Early in the Orion CPAS (Capsule Parachute Assembly System) project a main parachute was fabricated with lighter weight broadcloth in the lower part of the parachute skirt in order to look into different options for reducing the mass of the CPAS. At the end of Orion CPAS airdrop testing this parachute was used as a test equipment recovery parachute in order to gather data on the performance of this parachute. The parachute was the single recovery parachute in order to achieve the proper load under the parachute. It was flown on the final CPAS qualification test CQT 4-8 in September 2018.This paper will include imagery analysis, performance analysis based on all the gathered data, a full description of the configuration of the recovery parachute, as well as a comparison between this parachute and other CPAS recovery parachutes and other CPAS Main parachutes.

Description: This document defines the procedure to disconnect TBFM IDAC's connection with ATD-2's STBO System at the Washington Air Route Traffic Center. This is part of the ATD-2 ZDC training package that was presented in September 2017.

Description: This is the ATD-2 training presentation for ZDC. The original presentation was completed September 2017.The metering modes are described above. These will be updated depending on Modeset by the Ramp Manager, STBO Client will also display the Metering Mode Icon onthe right hand corner of the Toolbar.

Description: Over the past 5 years, the UAS integration into the NAS project has worked to reduce technical barriers to integration. A major focus of this work has been in support of RTCA SC-228. This committee has recently published the first UAS integration minimum performance standards (MOPS). This work has spanned detect and avoid (DAA) as well as command and control comm datalinks. I will discuss DAA efforts with focus on the human systems work. I will discuss how automation was discussed and addressed within this context. ICAO stood up a remotely piloted aircraft systems (RPAS) panel in 2014. They have developed an RPAS manual and are now working to revise existing annexes and standards and recommended practices. The Human In The System (HITS) has worked to infuse human factors guidelines into those documents. I will discuss that effort as well as how ICAO has defined and address autonomy. There is a great deal of interest in the control of multiple vehicles by a single operator. The UAS EXCOM Science and Research Panel (SARP) is holding a workshop on this topic in late June. I will discuss research performed on this topic when I worked for the Army and on-going work within the division and a NATO working group on Human-Autonomy Teaming.

Description: No abstract available

Description: No abstract available

Description: The National Aeronautics and Space Administration (NASA) has identified Multifunctional Structures for High Efficiency Lightweight Load-bearing Storage (M-SHELLS) as critical to development of hybrid gas-electric propulsion for commercial aeronautical transport in the N+3 timeframe. The established goals include reducing emissions by 80 and fuel consumption by 60 from todays state of the art. The advancement will enable technology for NASA Aeronautics Research Mission Directorates (ARMD) Strategic Thrust 3 to pioneer big leaps in efficiency and environmental performance for ultra-efficient commercial transports, as well as Strategic Thrust 4 to pioneer low-carbon propulsion technology in the transition to that scheme. The M-SHELLS concept addresses the hybrid gas-electric highest risk with its primary objective: to save structures energy storage system weight for future commercial hybrid electric propulsion aircraft by melding the load-carrying structure with energy storage in a single material. NASA's multifunctional approach also combines supercapacitor and battery chemistries in a synergistic energy storage arrangement in tandem with supporting good mechanical properties. The arrangement provides an advantageous combination of specific power, energy, and strength.

Description: Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional (3D) icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind tunnel testing was carried out for a 13.3-percent-scale semispan wing based upon the Common Research Model airplane configuration. The wind tunnel testing was conducted at the Office National dEtudes et de Recherches Arospatiales (ONERA) F1 pressurized wind tunnel with Reynolds numbers of 1.6 x 10(exp 6) to 11.9 x 10(exp 6 ) and Mach numbers of 0.09 to 0.34. Five different configurations were investigated using fully 3D, high-fidelity artificial ice shapes that maintain nearly all of the 3D ice-accretion features documented in prior icing wind tunnel tests. These large, leading-edge ice shapes were nominally based upon airplane holding in icing conditions scenarios. For three of these configurations, lower fidelity simulations were also built and tested. The results presented in this paper show that while Reynolds and Mach number effects are important for quantifying the clean-wing performance, there is very little to no effect for an iced wing with 3D, high-fidelity artificial ice shapes or 3D smooth ice shapes with grit roughness. These conclusions are consistent with the large volume of past research on iced airfoils. However, some differences were also noted for the associated stalling angle of the iced swept wing and for various lower fidelity versions of the leading-edge ice accretion. More research is planned to further investigate the key features of ice-accretion geometry that must be simulated in lower fidelity versions in order to capture the essential aerodynamics.

Description: In this paper, we introduce a level set method topology optimization method of structures subjected to coupled mechanical and thermal loads. Different examples considering compliance minimization and stress minimization under temperature and volume constraints, and mass minimization under stress and temperature constraints, are presented. The p-norm of the stress field and temperature field is used to approximate the maximum stress and temperature, respectively. The developed method is applied in the design of an L-bracket and a battery package. The results show that designs obtained by ignoring the thermal or structural constraints can result in high values of temperature or stress, respectively.

Description: Urban air taxis, also known as urban air mobility (UAM) vehicles, are anticipated to be an area of significant market growth in the near future. These vehicles are typically vertical take-off and landing (VTOL) designs which are capable of carrying 1 to 30 passengers in an intra-urban environment with flights of less than 50 nautical miles. Development of UAM vehicles and their integration into the airspace will be enabled by advancements in a number of areas including electrified propulsion systems, structures, acoustics, automation, and controls. However, the strong multidisciplinary interactions for these unique vehicles presents a significant new design challenge. This work describes the development of a multidisciplinary analysis and optimization environment which can be used to support the conceptual design of these UAM vehicles, using efficient gradient based optimization with analytic derivatives. The tools included in this multidisciplinary analysis model the aircraft trajectory, vehicle aerodynamics, structures, and electrified propulsion system. The multidisciplinary environment created in this research is unique in that all the physics tools are tightly integrated together, with the trajectory model directly calling the aerodynamics, structures, and propulsion models. This multidisciplinary analysis environment is then demonstrated in the design optimization of a turboelectric tiltwing UAM vehicle concept.

Description: An ice shape database has been created to document ice accretions on a 21-inch chord NACA0012 model and a 72-inch chord NACA 23012 airfoil model resulting from an exposure to a Supercooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each accretion. The icing conditions used in the test matrix were based upon previously used conditions on the same models but with an alternate approach to evaluation of drop distribution effects. Ice shapes resulting from the bimodal distribution as well as from equivalent monomodal drop size distributions were obtained and compared. Results indicate that the ice shapes resulting from the monomodal and bimodal drop size distributions had similar shapes, but the bimodal distributions had greater mass and volume measurements and icing limits that extended further back on the chord of the model.

Description: As both NASA and the aeronautics industry recognize the need for higher fuel efficiency and lower carbon emissions in both commercial airline and private aviation applications, development of all-electric or hybrid electric aircraft have garnered renewed interest in the aviation community. For the particular example of the hybrid-electric option, the solid oxide fuel cell (SOFC) is an attractive option for the power source, due to its potential to utilize aviation fuels thereby having minimal impact to aviation infrastructure. SOFC stack performance depends upon many factors, one of the most important is the way the oxidant and fuel gases are delivered to the fuel cells. System modeling of various aircraft configurations for FUELEAP (Fostering Ultra-Efficient, Low-Emitting Aviation Power) point to the need to operate SOFC stacks at high current densities. This creates challenges in the thermal profile of the stacks with potential to create large thermal gradients and hot spots. This study investigates two types of commercial solid oxide fuel cell stacks, the cross flow and co-flow gas designs, both convectively cooled with cathode air. High fuel utilization factors were also employed under varying electrical loads expected from the demands of flight. In addition, performance, range of operation and endurance were investigated under conditions of high current loads and thermal cycling. Evaluations include the study of gas kinetic using electrochemical spectroscopy. Testing took place at the facilities of NASA Glenn using a commercial test system (FuelCon AG, Magdeburg Germany). These studies are crucial to the Glenn Research Center's ability to conduct research, evaluation and development of the next-generation SOFC based stacks for cutting-edge energy technologies for aerospace applications. This study supports NASA's Convergent Aeronautics Solutions' (CAS) FUELEAP project.

Description: Understanding the aerodynamic impact of swept-wing ice accretions is a crucial component of the design of modern aircraft. Computer-simulation tools are commonly used to approximate ice shapes, so the necessary level of detail or fidelity of those simulated ice shapes must be understood relative to high-fidelity representations of the ice. Previous tests were performed in the NASA Icing Research Tunnel to acquire high-fidelity ice shapes. From this database, full-span artificial ice shapes were designed and manufactured for both an 8.9%-scale and 13.3%-scale semispan wing model of the CRM65 which has been established as the full-scale baseline for this swept-wing project. These models were tested in the Walter H. Beech wind tunnel at Wichita State University and at the ONERA F1 facility, respectively. The data collected in the Wichita St. University wind tunnel provided a low-Reynolds number baseline study while the pressurized F1 facility produced data over a wide range of Reynolds and Mach numbers with the highest Reynolds number studied being approximately Re=11.9x106. Past work focused on only three different fidelity variations for ice shapes based on multiple icing conditions. This work presents a more detailed investigation into several fidelity representations of a single highly three-dimensional scallop ice accretion. Sensitivity to roughness size and application technique on a low-fidelity smooth ice shape is described. The data indicate that the aerodynamic performance is not especially sensitive to the grit variations. An ice accretion code was also used to generate ice shapes for aerodynamic testing and comparisons. These ice shapes have a general appearance like the low-fidelity smooth ice shapes, but in this case, the computer-generated ice shape is significantly smaller. As such, the impact of that ice shape on the aerodynamic performance of the wing is reduced compared to the smooth ice shape based on the icing experiment for those same conditions. Spanwise discontinuities were also introduced to a low-fidelity ice shape in an attempt to quantify the impact of those variation in the high-fidelity ice shape. While the lift data indicate good agreement between the high-fidelity ice shapes and the low-fidelity ice shapes and the low-fidelity ice shapes with spanwise discontinuities, a closer investigation of the data suggests potential, significant differences in the flowfield. These results were similar at both facilities over the wide range of test conditions utilized.

Description: This presentation will be given as part of the UAS EXCOM Science and Research Panel's (SARP) workshop on multiple UAS controlled by a single operator. Participants were asked to identify public use cases for multiple UAS control and identify research, policy and technical gaps in those operations. The purpose of this workshop is to brainstorm, categorize and prioritize those use canses and gaps. Here, I will discuss research performed on this topic when I worked for the Army and on-going work within the division and a NATO working group on Human-Autonomy Teaming.

Description: This presentation will be given as part of the UAS EXCOM Science and Research Panel's (SARP) workshop on multiple UAS controlled by a single operator. Participants were asked to identify public use cases for multiple Unmanned Aircraft Systems (UAS) control and identify research, policy, and technical gaps in those operations. The purpose of this workshop is to brainstorm, categorize, and prioritize those use cases and gaps. Here, I will discuss research performed on this topic when I worked for the Army and on-going work within the division and a NATO working group on Human-Autonomy Teaming.

Description: NASA RPAS Operational and Research Activities presentation discusses the UAS flight operations. UAS vehicles are discussed along with the missions they supported. This is a high level overview of UAS operations at NASA being presented to the RPAS (Remotely Piloted Aircraft Systems) Symposium.

Description: No abstract available

Description: Description and Update of NASA UAS in the NAS Project

Description: Simulating separated flows at high Reynolds numbers using Reynolds Averaged Navier-Stokes (RANS) modeled equations remains a challenge in aeronautics. The main hindrance to progress stems from the lack of extended de- tailed data pertinent to the root cause of failure of RANS models, as well as the little progress in RANS modeling innovations in the past several decades. The goal of the current effort is to generate data for separated flow at a Reynolds numbers where conventional models are challenged. We use Direct Numerical Simulations to model turbulent flow over the wall-mounted hump configuration to investigate the physics of flow separation and boundary layer recovery, as well as provide data relevant to the modeling community. A chord-based Reynolds number of Re(sub c) = 47,500 is considered with a turbulent inflow profile of Re(sub ) = 1,400 ( /c = 3%). We use FDL3DI, a code that solves the compressible Navier-Stokes equations using high-order compact-difference scheme and filter, with the standard re- cycling/rescaling method of generating turbulent boundary layers as inflow to the computational domain. Two differ- ent configurations of the upper-wall are analyzed for two sets of boundary conditions (slip and no-slip). The results are compared with the available higher Re(sub c) (= 936,000, Re(sub ) = 7,200, /c = 0.77%) experiment for major flow features. The simulated lower Rec allows for DNS-like mesh resolutions, and adequately wide spans. The results from these simulations show earlier separation and delayed reattachment compared to Re(sub c) = 936,000, and significantly higher skin friction in the forebody of the hump. We also find that the upper-wall shape and boundary condition influence pressure distribution over the hump, whereas skin friction is only influenced by the boundary condition.

Description: Overview of Workshop terms and goals for Enabling Autonomous Flight and Operations in the National Airspace.

Description: No abstract available

Description: This study presents an onboard decision-making architecture for small unmanned aerial systems (sUAS). The decision-maker is part of NASA's SAFE50 project that is working under the UAS Traffic Management (UTM) Technical Capability Level (TCL) 4 to provide autonomous point-to-point UAV flight in BVLOS, high-density urban environments. The decision-maker monitors various metrics to determine the safety and feasibility of the mission and categorizes flight states as Nominal, Off-Nominal, Alternate Land, and Land Now in a finite state machine. Changes in the monitored metrics serve as transitions in the state machine and trigger replanning. Navigation degradation and communication failure are simulated to show the feasibility of the decision-maker framework in appropriately switching the flight state.

Description: An alternative process technique, namely vacuum-assisted axial injection potting (VaAIP), has been developed to pot the Litz wires in the stator winding of high power density electric motors for the future electrified aircrafts. Initial trials of the process showed significant improvement in potting quality with less voids, thus potential improvement in thermal management of the motors. As an initial effort of pot-ability assessment, microstructures, 2-D and 3-D, of the Litz wires including dimensions and distribution of conductor filament, coating, and open spaces; packing patterns; shape/configuration changes of each bundles or the overall cross-sections per degree of twist were determined and quantified successfully. The microstructure analyses were performed not only for effective potting process development but also for more realistic electro-thermal modeling solutions. This paper will present results of the microstructure analyses, potentials of the VaAIP process from the trials, and future plans for scale-up and implementation of the process into a full-scale prototype stator winding.

Description: This presentation summarizes the current plans and efforts at NASA/Goddard to develop new thermal control technology for anticipated future missions. It will also address some of the programmatic developments currently underway at NASA, especially with respect to the NASA Technology Development Program and will highlight some of the latest flight project activities at GSFC. While funding for basic technology development is still scarce, significant efforts are being made in direct support of flight programs. New technology development continues to be driven by the needs of future missions, and applications of these technologies to current Goddard programs will be addressed. Many of these technologies also have broad applicability to DOD, DOE, and commercial programs. Partnerships have been developed with the Air Force, Navy, and various universities to promote technology development. Technology development activities supported by the internal research and development (IRAD) program, the Small Business Innovative Research (SBIR) program, and other technology development programs are reviewed in this presentation. Specific technologies addressed include; micro-channel heat transfer, latest developments of electro-hydro-dynamically pumped systems, Atomic Layer Deposition (ALD), thermal control coatings, and various other research activities.

Description: The talk will cover various research and development challenges and opportunities related to enabling autonomous flight and airspace operations. Particularly, it will address the needs and importance for enabling autonomous operations, various technical challenges and opportunities, and minimum viable product strategy.

Description: No abstract available

Description: These slides present NASA's vision, historical overview , and current Unmanned Systems projects at AFRC.

Description: Additive manufacturing methods for producing single materials are rapidly improving. The resulting material properties and microstructures are becoming more comparable to those of conventionally fabricated materials. However, the need for multi-functional and complex structures and components requires additional innovations in manufacturing such as multi-material and hybrid additive manufacturing approaches. Additive manufacturing machines with multiple print capabilities and combinations of AM, machining, and conventional processing methods will further open up design spaces and possibilities. In this presentation, several examples of the needs and methods for multi-material fabrication will be discussed with a focus on aerospace applications. Direct printing of silver coils in conjunction with fused deposition modeling, machined parts, and, binder jetting is being developed for innovative stator designs. Binder jetting of silicon-based materials with powder bed additions is being developed for heat exchanger applications. Additive manufacturing of bi-material systems is being pursued to fabricate lightweight, integrated, multifunctional structures.

Description: Solar activity is a manifestation of magnetic self-organization processes that involve complex dynamical coupling of various layers of the Sun acting over a broad range of spatial and temporal scales. Synergy of observational, theoretical, and modeling efforts is key to understanding solar activity variation, dynamics, and evolution and to developing reliable physics-based forecasts of long-term solar cycles and short-term activity manifestations, seasons of solar activity, such as periods of enhanced flaring and CME activity. The session welcomes observers, modelers, and theoreticians to share their results and ideas and to discuss current challenges, development of emerging fields (such as data assimilation), and the analysis of historical and modern observational data using theoretical modeling, interpretations, and predictions.

Description: NASA is conducting research under the UAS Integration in the NAS Project to develop standards that will enable mid-size and large unmanned aircraft to fly unrestricted in the National Airspace System. As these efforts move into its second phase, NASA is planning a series of flight tests and demonstrations, integrating industry partners' technologies. These events will not only provide valuable data to inform the RTCA Special Committee 228 DAA and C2 MOPS, but also provide an opportunity for the UAS community to test their technologies in a realistic environment. An overview of NASA UAS-NAS research will be presented touching on human systems integration, modeling and simulation and guidance and control. Plans for Flight Test 6 and Systems Integration Operationalization (SIO) will also be presented. The purpose of this meeting is to share with Kitty Hawk, at a high level, UAS-NAS research and discuss potential future collaboration between NASA and Kitty Hawk.

Description: NASA has been exploring the use of artificial intelligence technologies to improve vehicle and airspace capabilities for over 20 years. This research has ranged from the use of neural nets to allow adaptive control, to autonomous rotorcraft operations, to real-time prognostics, to an eventual goal of autonomous vehicles operating in an autonomous airspace, in the context of smart communities. Examples of past research and future directions in autonomy for aeronautics will be presented.

Description: With the rise in big data and analytics, machine learning is transforming many industries. It is being increasingly employed to solve a wide range of complex problems, producing autonomous systems that support human decision-making. For the aircraft engine industry, machine learning of historical and existing engine data could provide insights that help drive for better engine design. This work explored the application of machine learning to engine preliminary design. Engine core-size prediction was chosen for the first study because of its relative simplicity in terms of number of input variables required (only three). Specifically, machine-learning predictive tools were developed for turbofan engine core-size prediction, using publicly available data of two hundred manufactured engines and engines that were studied previously in NASA aeronautics projects. The prediction results of these models show that, by bringing together big data, robust machine-learning algorithms and automation, a machine learning-based predictive model can be an effective tool for turbofan engine core-size prediction. The promising results of this first study paves the way for further exploration of the use of machine learning for aircraft engine preliminary design.

Description: Throughout the world, especially in dense urban environments, the quality of life is being negatively impacted by ever growing commute time. Travel, beyond commuting, is increasingly driven by door-to-door challenges ? not just gate-to-gate considerations. Air Mobility may be an approach to address these challenges, as it can effectively convert our 2D mobility system to a 3D mobility system, vastly increasing mobility options.

Description: Introduce mobility challenge, how air mobility can address the mobility challenge, then how an Air Mobility Data & Reasoning Fabric can enable the envisioned future air mobility. Poses the question of what is an effective role for NASA in enabling an Air Mobility Data & Reasoning Fabric.

Description: Overview NASA Aeronautics activities, and how NASA Ames Research Center contributes to NASA's Aeronautics activities.

Description: No abstract available

Description: The durability of gas-turbine engine components can be significantly affected by the ingestion of siliceous particles, which can melt at high temperature and corrode protective coatings that are essential for long life requirements. The silicate debris consists mainly of CaO-MgO-Al2O3-SiO2 (CMAS) and is usually ingested by aircraft engines during and after take-off, sticking to their hot surfaces and resulting in the formation of calcium rare-earth silicate oxyapatites. The thermochemistry of coatings and their reaction products with molten silicate debris are crucial to understand in order to improve the durability of gas-turbine engines. Here we discuss results of high temperature drop solution calorimetry, drop-and-catch calorimetry (DnC) and differential thermal analysis (DTA) techniques for the thermodynamic properties of both thermal barrier coatings (TBCs) and environmental barrier coatings (EBCs) and their reaction with CMAS compositions. The enthalpies of solution of Y2Si2O7, Yb2Si2O7, 31YSZ, and 16RESZ based coatings and the oxyapatite are moderately positive. However, oxyapatite formation is only favorable over coating dissolution in terms of enthalpy for 7YSZ. The enthalpies of mixing between the coatings and the molten silicate are less exothermic for Yb2Si2O7 and CaYb4Si3O13 than for 7YSZ, indicating lower energetic stability of the latter against molten silicate corrosion. We also report for the first time the calorimetric measurements of the enthalpies of formation of rare-earth silicate based EBC coatings and oxyapatites (rare-earth, RE = Y, Yb, Gd, Dy, Er, Nd and Sm).

Description: Despite the introduction of flight, duty, and rest time regulations to reduce the risk of sleepiness, airline pilots often encounter elevated sleepiness during flight. To combat this sleepiness, in some instances, pilots can take a short nap on the flight deck (controlled rest) to improve their alertness. Little is known, however, as to when and how often this countermeasure is used operationally. Methods: Forty-four pilots from a European carrier wore actiwatches and filled in an electronic sleep and work diary for approximately 2 weeks resulting in data from 239 flights. Self-reported in-flight rest periods were used to set rest intervals and sleep was estimated within these intervals using Philips Actiware 6.0.9. Wake threshold selection was set to medium; sleep threshold detection algorithm was set to 10 immobile minutes at sleep onset and sleep end. Timing of sleep periods was analyzed relative to home base time. Results: Preliminary analyses showed that controlled rest was taken on 46% (n=110) of flights. On 23 flights (10%) pilots reported taking two controlled rest periods. Sleep, as estimated by actigraphy, was achieved during 80% (n=106) of controlled rest periods. The mean sleep duration was 32 ( 12) minutes estimated within successful controlled rest periods. Approximately two-thirds (67.5%, n=81) of all rest periods were initiated during home base time night (0000h-0800h). On 11% (n=26) of flights, pilots also reported taking bunk rest (longer rest period in a designated sleeping facility).Conclusion:This study shows that controlled rest is commonly used as a countermeasure to sleepiness on the flight deck. Further analysis is required to determine what other factors contribute to the decision to take controlled rest, and how effective it is in reducing sleepiness on the flight deck.

Description: No abstract available

Description: This paper explores the novel Strayton engine concept. This engine combines the cycles of a Brayton engine with that of a Stirling engine to create a highly efficient recuperating gas turbine engine. In the explored case, both Brayton cycle and Stirling cycle engines are used to generate electrical power. Additionally, the Stirling engine is used to draw heat out of the Brayton turbine (acting to cool the turbine blades), while also pumping heat into Brayton cycle just before combustion occurs (acting as the mechanism for recuperation). The purpose of this paper is to detail the system level modeling techniques used to generate the simulation, perform a cycle analysis of the combined cycle engine, identify key technologies and challenges associated with the concept, and compare potential performance gains with existing gas turbine engines and internal combustion engines. Topics such as controls, blade cooling effects, engine weight, and heat transfer using heat pipe are also explored. Results from this work show potential architectures that could provide the required heat transfer rates, potential control strategies, and performance benefits, including efficiency gains between 10% and 3% on engines ranging from 200HP to 670HP with the combined cycle engine.

Description: NASAs Commercial Supersonic Technology (CST) project has formulated a technical challenge to design a quiet propulsion system for a low boom supersonic aircraft that meets Federal Aviation Authoritys airport noise regulations with sufficient margin. Several proposed configurations take advantage of shielding from the wing or other air-frame components. Development of carefully validated computational tools are necessary for critically evaluating installation concepts that are currently being proposed to meet the technical challenge. Semi-empirical models that predict the noise reduction potential of arbitrary shielding surfaces are yet to mature. Another key challenge is the systematic assessment of additional noise from the interaction between high speed jet turbulence and a surface in its vicinity. As a first step towards predicting noise reduction due to radical installation concepts from first principles, we simulate the noise generated by a high speed turbulent round jet near a simple planar surface. Detailed comparisons are made with a dedicated experiment conducted at NASAs Glenn Research Center. Sensitivity of far-field noise predictions to grid resolution is systematically documented. A permeable Ffowcs Williams Hawkings (FWH) surface enclosing both the jet and the shielding surface is used to predict far-field noise from the simulated flowfield. Details of the structured overset grids, numerical discretization, and turbulence model are provided. Near-field comparisons to PIV data and far-field comparisons to microphone array measurements are discussed. Excellent agreement for an initial validation study on an isolated free round jet was obtained and the findings were utilized in the jet surface interaction study. The split between shielded and reflected side of the microphone array was captured with good agreement, as well as the peak in the noise spectra due to scattering of turbulent energy into sound by the trailing edge of the surface.

Description: No abstract available

Description: No abstract available

Description: Noise has been identified as a major challenge to community acceptance of Urban Air Mobility Systems. The purpose of this paper is to assist designers, developers, and implementers in understanding the various factorsfrom the noise source itself to the conditions of the communitythat influence how the community is likely to respond to the introduction of a new noise source. Particular consideration is given to the role of non-acoustical factors and suggestions are offered as to how future research could help advance the understanding of community acceptance of Urban Air Mobility and other emergent vehicle systems.

Description: What is needed, on a regional level, to prepare for future urban air mobility operations in terms of airspace management, infrastructure, community, and aircraft.

Description: The NASA Protoflight Research Initiative is an internal NASA study conducted within the Office of the Chief Engineer to better understand the use of Protoflight within NASA. Extensive literature reviews and interviews with key NASA members with experience in both robotic and human spaceflight missions has resulted in three main conclusions and two observations. The first conclusion is that NASA's Protoflight method is not considered to be "prescriptive." The current policies and guidance allows each Program/Project to tailor the Protoflight approach to better meet their needs, goals and objectives. Second, Risk Management plays a key role in implementation of the Protoflight approach. Any deviations from full qualification will be based on the level of acceptable risk with guidance found in NPR 8705.4. Finally, over the past decade (2004 - 2014) only 6% of NASA's Protoflight missions and 6% of NASA's Full qualification missions experienced a publicly disclosed mission failure. In other words, the data indicates that the Protoflight approach, in and of it itself, does not increase the mission risk of in-flight failure. The first observation is that it would be beneficial to document the decision making process on the implementation and use of Protoflight. The second observation is that If a Project/Program chooses to use the Protoflight approach with relevant heritage, it is extremely important that the Program/Project Manager ensures that the current project's requirements falls within the heritage design, component, instrument and/or subsystem's requirements for both the planned and operational use, and that the documentation of the relevant heritage is comprehensive, sufficient and the decision well documented. To further benefit/inform this study, a recommendation to perform a deep dive into 30 missions with accessible data on their testing/verification methodology and decision process to research the differences between Protoflight and Full Qualification missions' Design Requirements and Verification & Validation (V&V) (without any impact or special request directly to the project).

Description: These cards are part of the Series 3 flight test documentation conducted between primary aircraft and intruder aircraft. This research is part of the UAS in the NAS Flight Test Program.