ALBERT

Beschreibung: A simple, systematic, optimized vortex-lattice approach is developed for application to lifting-surface problems. It affords a significant reduction in computational costs when compared to current methods. Extensive numerical experiments have been carried out on a wide variety of configurations, including wings with camber and single or multiple flaps, as well as high-lift jetflap systems. Rapid convergence as the number of spanwise or chordwise lattices are increased is assured, along with accurate answers. The results from this model should be useful not only in preliminary aircraft design but also, for example, as input for wake vortex roll-up studies and transonic flow calculations.

Beschreibung: As part of the program of flight tests of airplane propellers to determine compressibility effects at high speeds, preliminary flights have been made with a conventional three-blade propeller (Hamilton Standard 3155-6) on a Bell YP-39 airplane. This preliminary report presents the high-speed data obtained thus far with a brief analysis of the results.

Beschreibung: A 1/13-scale model of the forebody of the Republic F-105 with twin-duct wing-root inlets was tested in the Langley 4- by 4-foot supersonic pressure tunnel through a range of angle of attack from -4 deg to 15 deg at a Mach number of 2.01 and a Reynolds number of approximately 3.4 x 10(exp 6) per foot. The tests were made with four configurations which incorporated varying amounts of sweep and stagger of the inlet leading edges, modifications to the areas of the boundary-layer diverter floor plate, and modifications to the area of the boundary-layer diverter bleed slots. The highest overall pressure recovery at an angle of attack of 0 deg (average total-pressure recovery, 0.84 mass-flow ratio, 0.98) was achieved with configuration having an inlet leading-edge sweep angle of 58 deg with no leading-edge stagger. Stagger was found to improve the angle-of- attack performance, but at a sacrifice in inlet efficiency for an angle of attack of 0 deg. The boundary-layer diverter floor height, of the order of one boundary-layer thickness, was satisfactory for bypassing the fuselage boundary layer. The boundary-layer diverter-plate bleed slots were effective in increasing the total-pressure recovery of the inlet. The total-pressure-recovery contour plots, taken at the compressor-face station, indicate the existence of high-velocity "cores" throughout the inlet operating range.

Beschreibung: Flow spoiler and aerodynamic balance effects on oscillating hinge moments for swept fin-rudder combination in transonic wind tunnel

Beschreibung: A design guide is suggested as a basis for indicating combinations of airplane design variables for which the possibilities of pitch-up are minimized for tail-behind-wing and tailless airplane configurations. The guide specifies wing plan forms that would be expected to show increased tail-off stability with increasing lift and plan forms that show decreased tail-off stability with increasing lift. Boundaries indicating tail-behind-wing positions that should be considered along with given tail-off characteristics also are suggested. An investigation of one possible limitation of the guide with respect to the effects of wing-aspect-ratio variations on the contribution to stability of a high tail has been made in the Langley high-speed 7- by 10-foot tunnel through a Mach number range from 0.60 to 0.92. The measured pitching-moment characteristics were found to be consistent with those of the design guide through the lift range for aspect ratios from 3.0 to 2.0. However, a configuration with an aspect ratio of 1.55 failed t o provide the predicted pitch-up warning characterized by sharply increasing stability at the high lifts following the initial stall before pitching up. Thus, it appears that the design guide presented herein might not be applicable when the wing aspect ratios lower than about 2.0.

Beschreibung: Movable tail surface for aircraft control without flutter using X-15 scale model at hypersonic speed

Beschreibung: An investigation has been made at Mach numbers of 1.61 and 2.01 and Reynolds numbers of 1.7 x l0(exp 6) and 3.6 x l0(exp 6) to determine the pressure distributions over a swept wing with a series of 14 control configurations. The wing had 40 deg of sweep of the quarter-chord line, an aspect ratio of 3.1, and a taper ratio of 0.4. Measurements were made at angles of attack from 0 deg to +/- 15 deg for control deflections from -60 deg to 60 deg. This report contains tabulated pressure data for the complete range of test conditions.

Beschreibung: Factors affecting static, longitudinal, and directional stability characteristics of supersonic aircraft configurations

Beschreibung: Supersonic wind tunnel test of underslung scoop inlet on body of revolution

Beschreibung: Wind tunnel data of X-15 and B-52 aircraft models carry loads and mutual interference

Beschreibung: Supersonic wind tunnel test of twin-duct variable geometry side inlets

Beschreibung: Performance test data for pressure distributions over 60 deg delta wing at Mach 1.61 and 2.01

Beschreibung: Wind tunnel tests - effect of wind induced loads on dynamically scaled model of large missile in launching position

Beschreibung: An investigation of the aerodynamic characteristics of several hypersonic missile configurations with various canard controls for an angle-of-attack range from 0 deg to about 28 deg at sideslip angles of about 0 deg and 4 deg at a Mach number of 2.01 has been made in the Langley 4- by 4-foot supersonic pressure tunnel. The configurations tested we re a body alone which had a ratio of length to diameter of 10, the b ody with a 10 deg flare, the body with cruciform fins of 5 deg or 15 deg apex angle, and a flare-stabilized rocket model with a modified Von Karman nose. Various canard surfaces for pitch control only were te sted on the body with the 10 deg flare and on the body with both sets of fins. The results indicated that the addition of a flared afterbody or cruciform fins produced configurations which were longitudinally and directionally stable. The body with 5 deg fins should be capable of producing higher normal accelerations than the flared body. A l l of the canard surfaces were effective longitudinal controls which produced net positive increments of normal force and pitching moments which progressively decreased with increasing angle of attack.

Beschreibung: Internal aerodynamics and performance of clustered jet-exit installations at transonic speeds

Beschreibung: An experimental investigation was conducted to determine the performance characteristics an underslung nose-scoop air-induction system for a supersonic airplane. Five different nose shapes, three lip shapes, and two internal diffusers were investigated. Tests were made at Mach numbers from 0 to 1.9, angles of attack from 0 deg to approximately l5 deg, and mass-flow ratios from 0 to maximum obtainable. It was found that the underslung nose-scoop inlet was able to operate at Mach numbers from 0.6 to 1.9 over a large positive angle-of-attack range without adverse effects on the pressure recovery. Although there was no one inlet configuration that was markedly superior over the entire range of operating variables, the arrangement having a nose designed to give increased supersonic compression at low angles of attack, and a sharp lip (configuration designated N3L3) showed the most favorable performance characteristics over the supersonic Mach number range. Inlets with sizable lip radii gave satisfactory performance up to a Mach number of 1.5; however, as a result of an increase in drag, the performance of such inlets was markedly inferior to the sharp-lip configuration above Mach numbers of 1.5. Throughout the range of test Mach numbers all inlet configurations evidenced stable air-flow characteristics over the mass-flow range for normal engine operation. Analysis of the inlet performance on the basis of a propulsive thrust parameter showed that a fixed inlet area could be used for Mach numbers up to 1.5 with only a small sacrifice in performance.

Beschreibung: High subsonic speed of static longitudinal aerodynamic characteristics of delta wing configuration for angle of attack from 0 deg to 90 deg

Beschreibung: Stability and control of variable sweep wing configuration with outboard wing panels swept back 75 degrees at Mach 2.01

Beschreibung: Zero angle of attack performance of isentropic spike inlet designed for maximum external compression at hypersonic speed

Beschreibung: An investigation of some aspects of the sonic boom has been made with the aid of wind-tunnel measurements of the pressure distributions about bodies of various shapes. The tests were made in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 and at a Reynolds number per foot of 2.5 x 10(exp 6). Measurements of the pressure field were made at orifices in the surface of a boundary-layer bypass plate. The models which represented both fuselage and wing types of thickness distributions were small enough to allow measurements as far away as 8 body lengths or 64 chords. The results are compared with estimates made using existing theory. To the first order, the boom-producing pressure rise across the bow shock is dependent on the longitudinal development of body area and not on local details. Nonaxisymmetrical shapes may be replaced by equivalent bodies of revolution to obtain satisfactory theoretical estimates of the far-field pressures.

Beschreibung: Time histories of noise pressures near ground level were measured during flight tests of fighter-type airplanes over fairly flat, partly wooded terrain in the e Mach number range between 1.13 and 1.4 and at altitudes from 25,000 to 45,000 feet. Atmospheric soundings and radar tracking studies were made for correlation with the measured noise data. The measured and calculated values of the pressure rise across the shock wave were generally in good agreement. There is a tendency for the theory to overestimate the pressure at locations remote from the track and to underestimate the pressures for conditions of high tailwind at altitude. The measured values of ground-reflection factor averaged about 1.8 f or the surface tested as compared to a theoretical value of 2.0. P o booms were measured in all cases. The observers also generally reported two booms; although, in some cases, only one boom was reported. The shock-wave noise associated with some of the flight tests was judged to be objectionable by ground observers, and in one case the cracking of a plate-glass store window was correlated in time with the passage of the airplane at an altitude of 25,000 feet.

Beschreibung: Supersonic pressure distributions for tip and trailing edge controls on 60 deg delta wing

Beschreibung: Wind tunnel investigations of effect on static stability of modifications to swept wing fighter aircraft model

Beschreibung: Translating spike inlet air flow regulation characteristics from transonic to supersonic speeds at zero angle of attack

Beschreibung: Longitudinal and lateral stability and control characteristics of swept wing fighter aircraft

Beschreibung: Pressure distribution at supersonic speeds on conically cambered wing with and without pylon mounted engine nacelles

Beschreibung: Transonic wind tunnel study of aerodynamic characteristics of blunt reentry vehicles at varying angles of attack

Beschreibung: Effects of conical camber for triangular wing- body-tail combinations on aerodynamic characteristics

Beschreibung: Horizontal tail flutter in fighter aircraft at transonic speeds

Beschreibung: Aerodynamic interference effects on effectiveness of aircraft vertical tail at supersonic speeds

Beschreibung: Comparisons are made of experimental and theoretical zero-lift wave drag for several nose shapes, wing-body combinations, and models of current airplanes at Mach numbers up to 1.0. The experimental data were obtained from tests in the Ames 6- by6-foot supersonic wind tunnel and at the NACA Wallops Island facility. The theoretical drag was found by use of linear theory utilizing model area distributions. The agreement between theoretical and experimental zero-lift wave-drag coefficients was generally very good, especially for a fuselage or for fuselage-wing combinations that were vertically symmetrical. For other models that had rapid changes in body shape and/or were not vertically symmetrical, the agreement of theory with experiment ranged from fair to poor, depending on the severity of the change in shape.

Beschreibung: A brief investigation of the longitudinal stability and control effectiveness at supersonic speeds of a model of a low-wing missile with interdigitated tail surfaces was made in the Langley Unitary Plan wind tunnel. The data were obtained at Mach numbers M of 2.29, 2.97, and 3.51 for Reynolds number (based on the mean geometric chord of the wing) of 1.15 x 10(exp 6), 1.14 x 10(exp 6), and 1.11 x 10(exp 6), respectively. Data were obtained for three settings of the longitudinal control surfaces: with deflection of all surfaces, with deflection of the lower surfaces only, and with all surfaces undeflected. Directional stability data were obtained at M=3.51 for angles of attack of approximately 0 deg and 10 deg. These data, with summary data and typical schlieren photographs, are presented with only a brief analysis. The data indicate that the controls are effective throughout the Mach number range and lift-coefficient range (CL = -0.15 to 0.7, approximately) of the tests. There is a severe break in the pitching-moment curve at M=2.29 which might result in a pitch-up condition in flight, and also a large forward movement of the aerodynamic center with increasing Mach number that produces neutral longitudinal stability at M=3.51 for the moment center used in this investigation. The model was directionally unstable at M=3.51; however, the level of directional stability was about the same for 0 deg and 10 deg angles of attack.

Beschreibung: Static force and interference drag on externally carried bomb in flow field of supersonic, swept wing fighter-bomber aircraft

Beschreibung: Wind tunnel testing of two and four engine models of delta wing aircraft for transonic drag rise increment and maximum lift-drag ratio comparison

Beschreibung: Effects of boattail area contouring and simulated turbojet exhaust on loading and fuselage-tail component drag of twin-engine fighter-type airplane model

Beschreibung: Wind tunnel tests to determine lateral-directional stability of aircraft from transonic to supersonic speeds

Beschreibung: Wing-body combinations with wings of very low aspect ratio at supersonic speeds

Beschreibung: Performance characteristics of underslung vertical wedge inlet with porous suction at Mach numbers of 0.63 and 1.5 to 2.0

Beschreibung: Hypersonic flutter tests on rectangular flat-plate models and double-wedge airfoils in helium flow

Beschreibung: Wind tunnel studies at supersonic and transonic speeds to determine aerodynamic characteristics of variable sweep wing aircraft - configuration

Beschreibung: The static aeroelastic divergence characteristics of a delta-planform model of the canard control surface of a proposed air-to-ground missile have been studied both analytically and experimentally in the Mach number range from 0.6 to 3.0. The experiments indicated that divergence occurred at a nearly constant value of dynamic pressure at Mach numbers up to 1.2. At higher Mach numbers somewhat higher values of dynamic pressure were required to produce divergence. The analysis and the experiment indicate that the camber stiffness of the control surface and the stiffness of the control actuator are both important in divergence of surfaces of this type.

Beschreibung: Transonic performance of three turbojet nozzle- afterbody configurations

Beschreibung: Free flight drag measurements on delta wing with wing-fuselage-store

Beschreibung: Stage-stacking technique for predicting over-all performance in multistage axial flow turbojet compressor using interstage-air bleed

Beschreibung: Mach number and air temperature effect on hypersonic flow over blunt bodies

Beschreibung: Aerodynamic loads on external store adjacent to 60 deg delta wing at Mach numbers 0.75 to 1.96

Beschreibung: A supersonic wind-tunnel investigation on store interference has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.61. Forces and moments were measured on a large ogive-cylinder store in the presence of a 45 deg swept-wing-fuselage bomber configuration for a number of store locations below the fuselage center line. Results of the investigation show that large variations of store lift, drag, and pitch occur with changes in store or airplane angle of attack, store vertical location, and store horizontal location. The variation of the store forces and moments with respect to the chordwise location of the wing plan form indicates that the wing is a large factor in producing the interference loads on the store. Comparison of data for underfuselage and underwing store locations at an angle of attack of 0 deg showed maximum store drag interferences of similar magnitudes, but showed considerably smaller maximum interference on store lift an pitching moments for underfuselage store locations.

Beschreibung: Low cowl drag, external compression inlet with subsonic dump diffuser for high Mach number application

Beschreibung: Experimental investigation of high subsonic turbine with forty blade rotor with zero suction-surface diffusion

Beschreibung: Double-ramp side inlet with combinations of fuselage, ramp, and throat boundary layer removal

Beschreibung: Static longitudinal stability and control characteristics of wingless missile configuration at supersonic and hypersonic speeds

Beschreibung: Overall stage and stator blade element performance with straight stator and tilted stator in transonic axial flow compressor stage

Beschreibung: Pressure measurements in flight over conically cambered delta wing of F-102A aircraft at transonic speeds

Beschreibung: An exploratory wind-tunnel investigation has been made to determine the lift effects of blowing from nacelles over the upper surface of flaps on a model having a delta wing of aspect ratio 3. Several flap conditions were examined. High-pressure air was blown from an external-pipe arrangement supported above the wing to simulate jet-engine exhaust. The jet momentum- coefficient range was from 0 to 3.0 and the model angle of attack was 0 deg. The results of this limited investigation show that values of jet circulation lift coefficient larger than the Jet reaction were produced with blowing over flaps from nacelles mounted above the wing. 'I!heuse of double slotted flaps with the gap unsealed between the flaps and wing had a large detrimental effect on the lift capabilities. With these gaps sealed, larger lift coefficients were obtained when fantails were added to the nacelles. The longitudinal trim problems created by large diving moments were similar to those encountered with other jet-augmented-flap systems

Beschreibung: Problems involved in the stability and control of tailless airplanes are discussed. Such factors as the location of the aerodynamic center and its effect on the longitudinal stability, longitudinal trim with high-lift devices, the effects of various changes in the shape of the wing on lateral stability, and the effects of nacelles are covered. It appears that sufficient stability and controllability can be secured without sweepback. With sweepback, a flap over the center section of the wing may be used to serve the dual purpose of elevator control and high-lift device. Sweepback introduces undesirable stalling characteristics, however, and may require auxiliary devices to prevent stalling of the tips.

Beschreibung: An analysis, based on the linearized thin-airfoil theory for supersonic speeds, of the wave drag at zero lift has been carried out for a simple two-body arrangement consisting of two wedgelike surfaces, each with a rhombic lateral cross section and emanating from a common apex. Such an arrangement could be used as two stores, either embedded within or mounted below a wing, or as auxiliary bodies wherein the upper halves could be used as stores and the lower halves for bomb or missile purposes. The complete range of supersonic Mach numbers has been considered and it was found that by orienting the axes of the bodies relative to each other a given volume may be redistributed in a manner which enables the wave drag to be reduced within the lower supersonic speed range (where the leading edge is substantially subsonic). At the higher Mach numbers, the wave drag is always increased. If, in addition to a constant volume, a given maximum thickness-chord ratio is imposed, then canting the two surfaces results in higher wave drag at all Mach numbers. For purposes of comparison, analogous drag calculations for the case of two parallel winglike bodies with the same cross-sectional shapes as the canted configuration have been included. Consideration is also given to the favorable (dragwise) interference pressures acting on the blunt bases of both arrangements.

Beschreibung: A simplified analysis of the velocity and deceleration history of missiles entering the earth's atmosphere at high supersonic speeds is presented. The results of this motion analysis are employed to indicate means available to the designer for minimizing aerodynamic heating. The heating problem considered involves not only the total heat transferred to a missile by convection, but also the maximum average and local time rates of convective heat transfer.

Beschreibung: A solution of the equations of the compressible laminar boundary layer including the effects of transpiration cooling is presented. The analysis applies to the flow over an isothermal porous plate with a velocity of fluid injection proportional to the reciprocal of the square root of the distance from the leading edge. The effect of several flow parameters on coolant-flow rates is discussed with the aid of representative examples. A stability analysis indicates that, although transpiration cooling requires a lower surface temperature for stable flow than does internal wall cooling, this lower temperature can be obtained with a smaller expenditure of coolant.

Beschreibung: An investigation was made of the flow downstream from a "two-dimensional" grid formed of parallel rods. In both two and three dimensional jet fields there is a critical range of grid density below which the downstream flow is stable and above which it is unstable. The flow can be completely stabilized by means of an adequate lateral contraction beginning immediately after the grid or by use of a fine-mesh damping screen parallel to the grid plane and within a definite range of positions downstream from the grid.

Beschreibung: Problem of improving thrust at low speeds is primarily one of reducing angle of attack of operation of sections to improve L/D or reducing blade helix angle. An analysis, based on recent propeller data, is presented for determining improvements in thrust or efficiency which could be obtained by increased number of blades, increased blade width, increased diameter, dual rotation, and two-speed gearing. All methods were found very effective, particularly two-speed gearing.

Beschreibung: Test of a ducted body with Internal flow were made in the 8-foot high-speed wind tunnel for the purpose of studying the effects on external drag and an critical speed of the addition of efficient inlet and outlet openings to a basic streamline shape. Drag tests of a 13.6- inch-diameter streamline body of fineness ratio 6.14 were made at Mach numbers ranging from 0.20 to 0.75. The model was centrally mounted on a 9-percent-thick airfoil and was designed to have an efficient airfoil-body juncture and a high critical speed. An air inlet at the nose and various outlets at the tail were added: drag and internal-flow data were obtained over the given speed range. The critical speed of the ducted bodies was found to be as high as that of the streamline body. The external - drag with air flow through the body did not exceed the drag of the basic streamline shape. No appreciable variation in the efficiency of the diffuser section of the internal duct occurred throughout the Mach number range of the tests.

Beschreibung: Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit

Beschreibung: In order to determine the critical stresses caused by an outward acting pressure on the upper surface of a wing due to the difference in internal and external pressures, torsional tests were made on two curved-sheet specimens subjected to an outward acting normal pressure. Results show that an outward acting normal pressure appreciable raises the critical shear stress for an unstiffened curved sheet; the absolute increase in critical shear stress is slightly greater for a 30 in. rib spacing than for a 10 in. rib spacing.

Beschreibung: Two airfoil plans were used for propeller blades. One is modified Clark Y section designed for structural reliability and the second an NACA 16 airfoil section designed to produce minimum aerodynamic losses. At low air speeds, the propeller designed for aerodynamic effects showed a gain of from 1.5 to 4.0 percent in propulsive efficiency over the conventional type depending on the pitch. Because of the numerous variables involved, the effect of each one on the aerodynamic characteristics of the propellers could not be isolated.

Beschreibung: Description is given of flight tests conducted on gun fairings, designed to correct the detrimental effects of the projecting and submerged wing guns on an F4F-3 fighter. It was found that the installation of unfaired guns on a clean wing resulted in a premature stall that increased the stalling speed in the carrier-approach and landing conditions of flight by suitably fairing the guns, it was possible to reduce the stalling speeds to values approaching very nearly the clean-wing values.

Beschreibung: Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.

Beschreibung: No abstract available

Beschreibung: No abstract available

Beschreibung: Pressure distribution measurements were made over an airfoil with slotted Frise aileron up to 0.76 Mach at various angles of attack and aileron defections. Section characteristics were determined from these pressure data. Results indicated loss of aileron rolling power for deflections ranging from -12 Degrees to -19 Degrees. High stick forces for non-differential deflections incurred at high speed, which were due to overbalancing tendency of up-moving aileron, may precipitate serious control difficulties. Detailed results are presented graphically.

Beschreibung: Methods are given of determining the potential flow plast an arbitrary cascade of airfoils and the inverse problem of determining an airfoil having a prescribed velocity distribution in cascade. Results indicated that Cartesian mapping function method may be satisfactorily extended to include cascades. Numerical calculation for computing cascades by Cartesian mapping function method is considerably greater than for single airfoils but much less than hitherto required for cascades. Detailed results are presented graphically.

Beschreibung: Flight tests were conducted on the OS2U-2 seaplane with simple circular-arc-type ailerons directly connected to the actuating torque tube. Two aileron test installations were made, differing only in the inclination of the projecting surface with the wing's upper surface. The lateral-control characteristics of the airplane were determined from data obtained in stalls and rudder-fixed aileron rolls. The revised ailerons were deficient in maximum rolling effectiveness, but were capable of controlling the rolling tendencies of the airplane near the stall.

Beschreibung: This report contains those results of the theory of wings and of wing sections which are of immediate practical value. They are proved and demonstrated by the use of the simple conceptions of "kinetic energy" and "momentum" only, familiar to every engineer; and not by introducing "isogonal transformations" and "vortices," which latter mathematical methods are not essential to the theory and better are used only in papers intended for mathematicians and special experts.

Beschreibung: Available experimental two-dimensional-cascade data for conventional compressor blade sections are correlated. The two-dimensional cascade and some of the principal aerodynamic factors involved in its operation are first briefly described. Then the data are analyzed by examining the variation of cascade performance at a reference incidence angle in the region of minimum loss. Variations of reference incidence angle, total-pressure loss, and deviation angle with cascade geometry, inlet Mach number, and Reynolds number are investigated. From the analysis and the correlations of the available data, rules and relations are evolved for the prediction of the magnitude of the reference total-pressure loss and the reference deviation and incidence angles for conventional blade profiles. These relations are developed in simplified forms readily applicable to compressor design procedures.

Beschreibung: A model of a cruciform missile configuration having a low-aspect-ratio wing equipped with flap-type controls was flight tested in order to determine stability and control characteristics while rolling at about 5 radians per second. Comparison is made with results from a similar model which rolled at a much lower rate. Results showed that, if the ratio of roll rate to natural circular frequency in pitch is not greater than about 0.3, the motion following a step disturbance in pitch essentially remains in a plane in space. The slope of normal- force coefficient against angle of attack C(sub N(sub alpha)) was the same as for the slowly rolling model at 0 degrees control deflection but C(sub N(sub alpha)) was much higher for the faster rolling model at about 5 degrees control deflection. The slope of pitching-moment coefficient against angle of attack C(sub m(sub alpha)) as determined from the model period of oscillation was the same for both models at 0 degrees control deflection but was lower for the faster rolling model at about 5 degrees control deflection. Damping data for the faster rolling model showed considerably more scatter than for the slowly rolling model.

Beschreibung: The temperature distributions encountered in thin solid wings subjected to aerodynamic heating induce thermal stresses that may effectively reduce the stiffness of the wing. The effects of this reduction in stiffness were investigated experimentally by rapidly heating the edges of a cantilever plate. The midplane thermal stresses imposed by the nonuniform temperature distribution caused the plate to buckle torsionally, increased the deformations of the plate under a constant applied torque, and reduced the frequency of the first two natural modes of vibration. By using small-deflection theory and employing energy methods, the effect of nonuniform heating on the plate stiffness was calculated. The theory predicts the general effects of the thermal stresses, but becomes inadequate as the temperature difference increases and plate deflections become large.

Beschreibung: Skin-temperature measurements have been made at several locations on a flat-faced cone-cylinder nose which was flight tested on a fivestage rocket-propeller model to a Mach number of 14.64 and a free-stream Reynolds number of 2.0 x 10(exp 6), based on flat-face diameter, at an altitude of 66,300 feet. The copper nose had a 29 deg total-angle conical section which was 1.6 flat-face diameters long. The aerodynamic-heating rates determined from the temperature measurements reached 1,440 Btu/( sec) (sq ft) on the flat face. The heating rates near the center of the flat face agreed well at Mach numbers up to 13.6 with those obtained by a theory for laminar stagnation-point heating in equilibrium dissociated air (Avco Res. Rep. 1). At Mach numbers above 13.6, the heating rates at locations near the center of the flat face became progressively lower than stagnation-point theory and. were 29 percent lower at Mach number 14.6 at the end. of the test. The reason for this behavior of the heating on the central part of the flat face was not determined. Excluding the relatively low heating rates that occurred on the central part of the nose at the highest Mach numbers, the distribution of experimental heating along the innermost 0.79 of the flat-face radius, expressed as a percentage of stagnation-point heating, was in fair agreement with the distribution predicted by laminar theory. At a location of 0.71 radii from the stagnation point, the experimental heating was very near 130 percent of the theoretical stagnation-point rate at Mach numbers from 11 to 14.5. The experimental beating rates on the conical section of the nose were in good agreement with laminar-cone theory using the assumption of theoretical sharp-cone static pressure on the conical section.

Beschreibung: The pitching and the yawing moments of a vee-type and a conventional type of tail surface were measured. The tests were made in the presence of a fuselage and a wing-fuselage combination in such a way as to determine the moments contributed by the tail surfaces. The results showed that the vee-type tail tested, with a dihedral angle of 35.3 deg, was about 71 percent as effective in pitch as the conventional tail and had a yawing-moment to pitching-moment ratio of 0.3. The conventional tail, the panels of which were all congruent to those of the vee-type tail, had a yawing-moment to pitching-moment ratio of 0.48. These ratios are in fair agreement with values calculated by methods shown in this and previous reports. The values of the measured moments were reduced from 15 to 25 percent of the calculated value by fuselage interference.

Beschreibung: Tests of two wing-body combinations have been conducted in the Langley 19-foot pressure tunnel at a Reynolds number of 4 x 10(exp 6) and a Mach number of 0.19 to determine the effects of the bodies on the wing span load distributions. The wings had 45 degrees sweepback of the quarter-chord line, aspect ratio 8.02, taper ratio 0.45, and incorporated 12-percent-thick airfoil sections streamwise. One wing was untwisted and uncambered whereas the second wing incorporated both twist and camber. Identical bodies of revolution, of 10:1 fineness ratio, having diameter-to-span ratios of 0.10, were mounted in mid-high-wing arrangements. The effects of wind incidence, wing fences, and flap deflection were determined for the plane uncambered wing. The addition of the body to the plane wing increased the exposed wing loading at a given lift coefficient as much as 10 percent with the body at 0 degrees incidence and 4 percent at 4 degrees incidence. The bending-moment coefficients at the wing-body juncture were increased about 2 percent with the body at 0 degrees incidence, whereas the increases were as much as 10 percent with the body at 4 degrees incidence. The spanwise load distributions due to the body on the plane wing as calculated by using a swept-wing method employing 19 spanwise lifting elements and control points generally showed satisfactory agreement with experiment. The spanwise load distributions due to body on the flapped plane wing and on the twisted and cambered wing were dissimilar to those obtained on the plane wing. Neither of the methods of calculation which were employed yielded distributions that agreed consistently with experiment for either the flapped plane wing or the twisted and cambered wing.

Beschreibung: Ice was formed on a full-scale unheated supersonic nose inlet in the NACA Lewis icing tunnel to determine its effect on compressor-face total-pressure distortion and recovery.Inlet angle of attack was varied from 0degrees to 12 degrees, free-stream Mach number from 0.17 to 0.28, and compressor-face Mach number from 0.10 to 0.47. Icing-cloud liquid-water content was varied from 0.65 to 1.8 grams per cubic meter at free-stream static air temperatures of 15 degrees and 0 degrees F. The addition of ice to the inlet components increased total-pressure-distortion levels and decreased recovery values compared withclear0air results, the losses increasing with time in ice. The combination of glaze ice, high corrected weight flow, and high angle of attack yielded the highest levels of distortion and lowest values of recovery. The general character of compressor-face distortion with an iced inlet was the same as that for the clean inlet, the total-pressure gradients being predominantly radial, with circumferential gradients occurring at angle of attack. At zero angle of attack, free-stream Mach number of 0.27, and a constant corrected weight flow of 150 pounds per second (compressor-face Mach number of 0.43), compressor-face total-pressure-distortion level increased from about 6 percent in clear air to 12 percent after 21 minutes of heavy glaze icing; concurrently, total-pressure recovery decreased from about 0.98 to 0.945. For the same operating conditions but with the inlet at 12 deg angle of attack, a change in distortion level occurred from about 9 percent in clear air to 14 percent after 2-1/4 minutes of icing, with a decrease in recovery from about 0.97 to 0.94.

Beschreibung: Tests were made in 8-ft high-speed wind tunnel to determine the drag reduction possible by eliminating the barrel jacket of a protruding 50-caliber aircraft gun. It was found that the drag of a standard aircraft gun protruding into the air stream at right angles to the flow can be reduced by 23% by discarding the barrel jacket. At 300 mph and sea-level conditions, this amounts to a decrease in drag of from 83 to 64 pounds. A rough surface finish on the barrel was found to have no adverse effects on the drag of the barrel, the drag being actually less at high Mach Numbers.

Beschreibung: Tank tests were made of a hull model of the Hughes-Kaiser cargo airplane for estimates of take-off performance and maximum gross load for take-off. At hump speeds, with the model free to trim, the trim and resistance were high, which resulted in a load-resistance ratio of approximately 4.0 for a gross load coefficient of 0.75. With a 4000,000-lb load, the full size craft may take off in 69 sec over a distance of 5600 ft.

Beschreibung: Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.

Beschreibung: Several tail modifications of the Brewster XSBA-1 scout-bomber were investigated and results compared. Modifications consisted of variation of the chord of the elevator and rudder while the total area of the surfaces is kept constant and variations of the total area of the vertical tail surface. Configuration number 2 reduced trim changes by 50 percent and reduced average elevator control force gradient from 30 to 27 pounds/g. Stick travel required to stall in maneuver was 4.6 inches.

Beschreibung: Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.

Beschreibung: Results of flight tests indicate that profile-drag coefficients which were obtained with the low-drag airfoils were lower than with the conventional types over the range of light coefficients tested. For comparable conditions of the lift coefficient and Reynolds Number, the low-drag airfoils have profile-drag coefficients which may be 27 percent lower than the profile drag of the conventional airfoils tested. Detailed results are presented graphically.

Beschreibung: This report gives the pressure distribution and resistance found by theory and experiment for simple quadrics fixed in an infinite uniform stream of practically incompressible fluid. The experimental values pertain to air and some liquids, especially water; the theoretical refer sometimes to perfect, again to viscid fluids. For the cases treated the concordance of theory and measurement is so close as to make a resume of results desirable. Incidentally formulas for the velocity at all points of the flow field are given, some being new forms for ready use derived in a previous paper. (author)

Beschreibung: The flow about slender flat-top wing-body configurations traveling at high supersonic speeds and small angles of attack is investigated analytically. In the case of conical configurations, approximate algebraic solutions to the flow field are obtained. In the case of configurations which are conical at the vertex but curved in the stream direction, these solutions are combined with a slender-body approximation to the generalized shock-expansion method to obtain the flow downstream of the vertex. Surface pressures were obtained experimentally at Mach numbers from 3.0 to 6.0 and angles of attack up to 6 deg for several flat-top wing-body configurations. These configurations consisted of half-bodies of revolution mounted beneath thin highly swept wings. Three different bodies were employed. The two conical bodies consisted of one-half of a fineness-ratio-5 cone and one-half of a fineness-ratio-2-1/2 cone. The body of the third configuration consisted of one-half of a fineness-ratio-5 ogive. For the ogive configuration, the leading edges of the wing were curved and designed to just maintain the theoretically determined bow shock along the leading edge at a Mach number of 5.0 and an angle of attack of 3 deg. The predictions of the conical flow theory of this paper for the surface pressures are found to be in good agreement with experiment at Mach numbers of 5.0 and 6.0 up to angles of attack of approximately 3 deg. Estimated lift, drag, and pitching-moment coefficients, as well as maximum lift-drag ratio, are also in good agreement with existing experimental data at a Mach number of 5.0 for a conical configuration having an arrow plan-form wing. It is also found that the generalized shock-expansion method yields reasonable good agreement with experiment for the surface pressures on the half-ogive configuration at a Mach number of 5.0 and an angle of attack of 3 deg.

Beschreibung: A pressure-distribution investigation of a wing-body combination has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01. The model configuration consisted of an ogive-circular-cylinder body (fineness ratio of approximately ii) and a wing with 45 deg of sweepback at the quarter-chord line, an aspect ratio of 4, and a taper ratio of 0.2. Data were obtained on high-, mid-, and low-wing configurations and for the body and wing alone for a range of angles of attack and yaw from 0 deg to 15 deg. The tabulated pressure coefficients are presented in this report.

Beschreibung: Heat-transfer measurements were made on a simulated glide-rocket shape in free flight at Mach numbers up to 10 and free-stream Reynolds numbers of 2 x 10 based on distance along surface from apex and 3 x 10 based on nominal leading-edge diameter. The model simulated the bottom of a 75 deg delta wing at 8O deg angle of attack. The data indicated that for the test conditions a modified three-dimensional stagnation-point theory will predict to reasonable engineering accuracy the heating on a highly swept wing leading edge, the heating being reduced by sweep by the 3/2 power of the cosine of the sweep angle. The data also indicate that laminar heating rates over the windward surface of a highly swept flat glider wing at moderate angles of attack can be predicted with reasonable engineering accuracy by flat-plate theory using wedge local flow conditions and basing Reynolds numbers on lengths from the wing leading edge parallel to the surface center line.

Beschreibung: Chemical sublimation has been employed for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight at speeds near a Mach number of 2.0. The tests have shown that laminar flow can be obtained over extensive areas of the wing with practical wing-surface conditions. In addition to the flow visualization tests, a method of continuously monitoring the conditions of the boundary layer has been applied to flight testing, using heated temperature resistance gages installed in a Fiberglas "glove" installation on one wing. Tests were conducted at speeds from a Mach number of 1.2 to a Mach number of 2.0, at altitudes from 35,000 feet to 56,000 feet. Data obtained at all angles of attack, from near 0 deg to near 10 deg, have shown that the maximum transition Reynolds number on the upper surface of the wing varies from about 2.5 x 10(exp 6) at a Mach number of 1.2 to about 4 x 10(exp 6) at a Mach number of 2.0. On the lower surface, the maximum transition Reynolds number varies from about 2 x 10(exp 6) at a Mach number of 1.2 to about 8 x 10(exp 6) at a Mach number of 2.0.

Beschreibung: Rough conventional, smooth conventional, and laminar-flow or low-drag sections were tested. The items covered are rotor thrust for fixed power in hovering, range and endurance at cruising speed, and power required at high-forward speed. Calculations indicated that a smooth conventional section gives marked performance gains. Smaller gains are obtainable by using a low-drag section. At high speeds or loads the low-drag section is inferior to the smooth conventional section.