ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Articles  (176)
  • thermal conductivity  (176)
  • Springer  (176)
  • American Chemical Society
  • 1995-1999  (84)
  • 1985-1989  (92)
  • Physics  (176)
  • Natural Sciences in General
  • 1
    ISSN: 1573-0956
    Keywords: (AGI) ; heat flow ; lithosphere ; thermal conductivity ; thermal diffusivity ; models ; uncertainty
    Source: Springer Online Journal Archives 1860-2000
    Topics: Geosciences , Physics
    Notes: Abstract Measurements on thermal conductivity and diffusivity as functions of temperature (up to 1150 K) and pressure (up to 1000 MPa) are presented for Archaean and Proterozoic mafic high-grade rocks metamorphosed in middle and lower crustal pressures, and situated in eastern Finland, central Fennoscandian Shield. Decrease of 12–20% in conductivity and 40–55% in diffusivity was recorded between room temperature and 1150 K, which can be considered as typical of phonon conductivity. Radiative heat transfer effects were not detected in these samples. Pressure dependencies of the samples are weak if compared to crystalline rocks in general, but relatively typical for mafic rocks. The temperature and pressure dependencies of thermal transport properties (data from literature and the present study) were applied in an uncertainty analysis of lithospheric conductive thermal modellings with random (Monte Carlo) simulations using a 4-layer model representative of shield lithosphere. Model parameters were varied according to predetermined probability functions and standard deviations were calculated for lithospheric temperature and heat flow density after 1500 independent simulations. The results suggest that the variations (uncertainties) in calculated temperature and heat flow density values due to variations in the temperature and pressure dependencies of conductivity are minor in comparison to the effects produced by typical variations in the room temperature value of conductivity, heat production rate or lower boundary condition values.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    Springer
    Journal of statistical physics 82 (1996), S. 1453-1466 
    ISSN: 1572-9613
    Keywords: Kinetic theory ; thermal conductivity ; molecular dynamics ; hard disks ; Enskog's Theory
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The phenomenon of heat conduction in a two-dimensional gas ofN hard disks is studied in the hydrostatic regime by means of nonequilibrium molecular dynamics (N ranging from 100 to 8000). For systems withN≥1500 the temperature and density profiles observed are in excellent agreement with the continuous theory, but the conductivityk differs from the one derived from Enskog's theory in a systematic way. This difference seems to slowly decrease with increasing density.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 3
    Electronic Resource
    Electronic Resource
    Springer
    Journal of statistical physics 57 (1989), S. 595-629 
    ISSN: 1572-9613
    Keywords: Neutron scattering function ; shear viscosity ; bulk viscosity ; thermal conductivity ; Green-Kubo integrand ; hard-sphere fluid ; short-time expansion
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The short-time behavior of the coherent intermediate scattering function for a fluid of hard-sphere particles is calculated exactly through ordert 4, and the other hydrodynamic correlation functions are calculated exactly through ordert 2. It is shown that for all of the correlation functions considered the Enskog theory gives a fair approximation. Also, the initial time behavior of various Green-Kubo integrands is studied. For the shear-viscosity integrand it is found that at densitynσ3=0.837 the prediction of the Enskog theory is 32% too low. The initial value of the bulk viscosity integrand is nonzero, in contrast to the Enskog result. The initial value of the thermal conductivity integrand at high densities is predicted well by Enskog theory.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 4
    Electronic Resource
    Electronic Resource
    Springer
    Applied mathematics and mechanics 18 (1997), S. 211-220 
    ISSN: 1573-2754
    Keywords: composite ; thermal conductivity ; inhomogeneous interphase ; Mori-Tanaka method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics , Mathematics , Physics
    Notes: Abstract Thermal conductivities of carbon/carbon fiber composites with inhomogeneous interphase are studied in thtis paper. The inhomogeneous interphase is modeled approximately as a multilayered structure consisting of many thin layers having homogeneous properties, and close-formed solution of the effective conductivities of the composites is obtained by using the Mori-Tanaka mean-field concept.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 5
    Electronic Resource
    Electronic Resource
    Springer
    Rheologica acta 35 (1996), S. 103-109 
    ISSN: 1435-1528
    Keywords: Transport properties ; thermal conductivity ; FENE dumbbell model ; polymer solutions ; thermal diffusion
    Source: Springer Online Journal Archives 1860-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: Abstract The phase-space kinetic theory for polymeric liquid mixtures has been further developed for molecular models without internal constraints. The theory provides expressions for the mass, momentum, and energy fluxes, each of which may in general be influenced by concentration, velocity, and temperature gradients. To illustrate the use of these results, the thermal conductivity for a dilute polymer solution is derived; the FENE dumbbell model is used to describe the mechanical behavior of the polymer chains. The Hookean dumbbell results can be obtained by letting the “finite extensibility parameter” b tend to infinity.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 6
    Electronic Resource
    Electronic Resource
    Springer
    Journal of superconductivity 12 (1999), S. 497-500 
    ISSN: 1572-9605
    Keywords: Organic superconductors ; Josephson plasma ; thermal conductivity ; upper critical field
    Source: Springer Online Journal Archives 1860-2000
    Topics: Electrical Engineering, Measurement and Control Technology , Physics
    Notes: Abstract Studies of heat conduction and microwave absorption in the vortex state of κ-(BEDT-TTF)2Cu(NCS)2 reveal some of the specific aspects of superconductivity in this system. Moreover they allow us to probe the destruction of bulk superconductivity by a magnetic field. The two set of results yield identical magnitudes for the upper critical field with a temperature dependence distinctly different from the one suggested by the onset of resistive transition.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 7
    Electronic Resource
    Electronic Resource
    Springer
    Journal of superconductivity 8 (1995), S. 445-448 
    ISSN: 1572-9605
    Keywords: High-T c superconductors ; thermal conductivity ; magnetization
    Source: Springer Online Journal Archives 1860-2000
    Topics: Electrical Engineering, Measurement and Control Technology , Physics
    Notes: Abstract We have investigated heat conduction of single crystal Ba1−xKxBiO3 in the temperature range of 2–300 K and in a magnetic field of up to 6 Tesla. Temperature dependence of thermal conductivityκ(T) reveals the participation of both electrons and phonons with their relative contributions that depend critically on the potassium doping concentration. Crystals underdoped with potassium (samples with higherT c) exhibit a strong suppression ofκ and a glass-like temperature dependence. In contrast, those with a higher potassium content (lowerT c) show an increase as temperature decreases with a peak near 23 K. Field dependence ofκ(H) is also very sensitive to the level of potassium doping. Crystals exhibiting a large phonon contribution show an initial drop inκ(H) at low fields followed by a minimum and then a slow rise to saturation as the field increases. The initial drop is due to the additional phonon scattering by magnetic vortices as the sample enters a mixed state. The high field behavior ofκ(H), arising from a continuous break-up of Cooper pairs, exhibits scaling which suggests the presence of an unconventional superconducting gap structure in this material.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 8
    Electronic Resource
    Electronic Resource
    Springer
    Journal of superconductivity 8 (1995), S. 449-452 
    ISSN: 1572-9605
    Keywords: thermal conductivity ; Andreev reflection ; vortex lines ; mixed phase
    Source: Springer Online Journal Archives 1860-2000
    Topics: Electrical Engineering, Measurement and Control Technology , Physics
    Notes: Abstract The increased thermal conductivity below Tc in YBa2Cu3O7−x (YBCO) is shown to agree with the microwave electrical conductivity, affirming that increase is due to quasiparticle conduction The field dependence, particularly in the conducting plane permits us to separate phonon and quasiparticle contributions for both YBCO and Tℓ2Ba2CuO6 single crystals.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 9
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 409-415 
    ISSN: 1572-9567
    Keywords: critical region ; ethane ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of ethane in the critical region has been measured isochorically at densities up to 1.76 times the critical density and at temperatures down to 0.13 K above the critical temperature. The measurements were performed with a thermal conductivity apparatus based on the parallelplate method. The experimental accuracy was 0.5 to 5%, depending on the distance to the critical point. The experimental results agree well with a recently developed crossover theory for the thermal diffusivity of fluids in the critical region.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 10
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 673-686 
    ISSN: 1572-9567
    Keywords: chlorofluorocarbons ; fluorocarbons ; nitrogen ; thermal conductivity ; toluene ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract In this paper we describe a version of a transient hot-wire apparatus which employs an integrating digital voltmeter to measure the bridge out-of-balance signal. The integrating period of the voltmeter is variable and is routinely set equal to one 60-Hz power-line cycle, 16.67 ms. Use of measurement or integration periods less than an integral multiple of the power-line period results in substantially more electronic noise and a significant degradation in experimental precision. A correction to the working equation which accounts for the integration of the out-of-balance signal is also presented. The precision of the digital voltmeter used with the apparatus is ±0.1 μV, which translates into an ultimate precision of ±0.03 mK in the measured temperature rise. In practice the precision in the temperature rise is typically ±0.3 mK, which represents a moderate improvement over the precision generally obtained with transient techniques employing automatic bridge balancing schemes. Although the current apparatus is designed principally for measurements of the thermal conductivity of liquids, it can been used for gas-phase measurements, with some decrease in accuracy due to the somewhat larger heat capacity correction which must be applied to the temperature rise measurements. The operation of the instrument was verified by measuring the thermal conductivities of toluene and nitrogen. Preliminary data are presented for the new environmentally acceptable fluorocarbons such as R-134a (CF3CH2F), R-123 (CHCl2CF3), and R-141b (CCl2FCH3).
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 11
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 417-426 
    ISSN: 1572-9567
    Keywords: carbon dioxide ; critical phenomena ; ethane ; methane ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A practical representation for the critical thermal conductivity enhancement is developed by incorporating a finite cutoff into the asymptotic mode-coupling integrals for the diffusivity associated with the critical fluctuations. This procedure yields a simplified approximation to a more complete nonasymptotic solution of the mode-coupling integrals obtained by us earlier. A comparison is made with thermal conductivity data for carbon dioxide, ethane, and methane.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 12
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 1013-1027 
    ISSN: 1572-9567
    Keywords: high pressure ; propane ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper presents thermal conductivity measurements of propane over the temperature range of 192–320 K, at pressures to 70 MPa, and densities to 15 mol · L−1, using a transient line-source instrument. The precision and reproducibility of the instrument are within ±0.5%. The measurements are estimated to be accurate to ±1.5%. A correlation of the present data, together with other available data in the range 110–580 K up to 70 MPa, including the anomalous critical region, is presented. This correlation of the over 800 data points is estimated to be accurate within ±7.5%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 13
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 63-78 
    ISSN: 1572-9567
    Keywords: R134a ; dilute gas ; refrigerant ; saturation properties ; 1,1,1,2-tetrafluoroethane ; thermal conductivity ; transport properties ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The paper contains a status report on an international project coordinated by the Subcommittee on Transport Properties of Commission 1.2 of the International Union of Pure and Applied Chemistry. The project has been conducted to investigate the large discrepancies between the results reported by various authors for the transport properties of R134a. The project has involved the remeasurement of the transport properties of a single sample of R134a in nine laboratories throughout the world in order to test the hypothesis that at least part of the discrepancy could be attributed to the purity of the sample. This paper provides an intercomparison of the new experimental results obtained to data in this project for the viscosity and the thermal conductivity in both gaseous and liquid phases. The agreement between the viscosity data from the laboratories contributing to the project was improved with several techniques, now producing consistent results. This suggests that the purity of the samples of R134a used in previous work was at least partly reponsible for the discrepancies observed. For the thermal conductivity in the liquid phase the results of the measurements are also more consistent than before, although not for all experimental techniques. Not all of the previous measurements suffered from significant sample impurities, so the present measurements on a consistent high-purity sample can he used to detect data sets which are outhers, possibly because of impurities. Identification of laboratories and techniques with systematic differences may require the examination of data for several fluids. The implications for future measurements of the transport properties of other refrigerants are significant.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 14
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 413-422 
    ISSN: 1572-9567
    Keywords: ethanol ; heptane ; nonane ; periodic techniques ; temperature ocillations ; thermal conductivity ; thermal dill'usivity ; water
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Simple temperature ocillation techniques are described for the last measurement of thermal dill'usivity and conductivity of liquids. The liquid specimen is a slab bounded above and below by a reference material. Two Peltier elements mounted on the outer Surfaces of the reference layers generate temperature ocillationS of these surfaces. Temperature waves propagate tluough the reference layers into the specimen. The thermal dilhusivity of the specimen is deduced by measuring all evaluating the amplitude attenuation and or the phase shift between the fundamental temperature oscillations at the surface of the liquid specimen and at a well-defined position inside the specimen. If the thermal diffusivity of the specimen is known. the thermal conductivity is determined by the measured amplitude attenuation and or the phase shill between the fundamental temperature oscillations at the surface of the reference layer and at the surface of the specimen. Slab and semi-infinite body geometries are considered. Measurement cells are designed and experiments are carried out with water, ethanol. heptane. monane. and glycerine. The results of the measurements of thermal dilhusivity asree very well, and those of thermal conductivity reasonably well, with the data obtained from the literature.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 15
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 375-399 
    ISSN: 1572-9567
    Keywords: coaxial cylinders ; high pressure ; refrigerants ; HFC-125 ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Measurements of the thermal conductivity of HFC-125 that have been made by a coaxial cylinder cell operating in steady state are reported. The measurements of the thermal conductivity of HFC-125 were performed along several quasi-isotherms between 300 and 515 K in the gas phase and the liquid phase. The pressure range covered varies from 0.1 to 53 MPa. Based on the measurement of more than 600 points, an empirical equation is provided to describe the thermal conductivity outside the critical region as a function of temperature and density. A careful analysis of the various sources of error leads to an estimated uncertainty of approximately ± 1.5%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 16
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 665-676 
    ISSN: 1572-9567
    Keywords: density ; myocardium ; swine ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper presents the experimental technique and results for the thermal conductivity, thermal diffusivity, and density of swine myocardial tissue. These properties were measured for freshly excised tissue. Thermal properties were measured using a self-heated thermistor probe, while the density was measured using a water displacement method. Thermistor probes were inserted into the tissue of interest and were used to supply heat within the tissue as well as to monitor the temperature rise in the tissue. An empirical calibration procedure was used to measure the properties of the tissue at different temperatures. The measurement instrument was first calibrated against agar-gelled water and glycerol at each temperature. The measurements were made at temperatures of 25, 37, 50, 62, and 76°C. The uncertainty in the measurement ranges from 2% at lower temperatures to about 5% at higher temperatures (T 〉 50°C). The properties of the tissue depend significantly on the water content. At temperatures higher than 50°C, there is significant water loss from the tissue during the procedure. The water loss is found to vary exponentially with the increase in temperature relative to ambient. Consequently, there is a decrease in the thermal conductivity values with increasing temperature. This decrease, however, is not as much as one would expect from the water loss data. A hypothesis to explain the relationships among water loss, cell damage, and thermal properties is proposed.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 17
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 597-606 
    ISSN: 1572-9567
    Keywords: binary mixtures ; low temperatures refrigerants ; R22 ; R1426 ; R152a ; thermal conductivity ; transient method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The paper presents the thermal conductivity of mixtures of liquid refrigerants, The group of systems studied consists of two binary mixtures of R22/R142b and R22/R152a. The measurements have been carried out in the temperature range 160–300 K for pressures From 0.2 to 8.0 MPa in a transient coaxial-cylinder instrument. The uncertainty of the thermal conductivity data is estimated to be ±2%. The experimental method and apparatus were validated by using the measurements of refrigerant R22. The results presented have been used to develop a correlation for the description of the thermal conductivity of refrigerants.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 18
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 561-571 
    ISSN: 1572-9567
    Keywords: alternative refrigerants ; difluoromethane (HFC-32) ; pentafluoroethane (HFC-125) ; 1,1,1-trifluoroethane (HFC-143a) ; dichloropentafluoropropanes (HCFC-225ca, HCFC-225cb) ; liquid phase ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Measurements ofthe thermal conductivity of five alternative refrigerants. namely, difluoromethane HFC-321. pentafluoroethane (HFC-125), 1,1,1-trifluoroethane (HFC-143a), and dichloropentafluoropropanes (HCFC-225ca and HCFC-225cb). are carried out in the liquid phase, The range of temperature is 253–324 K for HFC-32, 257–305 K for HFC-125, 268–314 K for HFC-134a. 267–325 K for HCFC-225ca, and 286–345 K for HCFC-225cb, The pressure rank is from saturation to 30 MPa, The reproducibility of the data is better than 0.5% and the accuracy of the data is estimated to be of the order of 1%. The experimental results for the thermal conductivity ofeach substance are correlated by an equation which is a function of temperature and pressure. A short discussion is given to the comparison of the present results with literature values for HFC-125, The saturated liquid thermal conductivity values of HFC-32. HFC-125, and HFC-143a are compared with those of chlorodifluoromethane (HCFC-22) and tetrafluoroethane (HFC-134a) and it is shown that the value of HFC-32 is highest, while that of HFC-125 is lowest, among these substances, The dependence of thermal conductivity on number of fluorine atoms among the refrigerants with the same number of carbon and hydrogen atoms is discussed.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 19
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 1237-1246 
    ISSN: 1572-9567
    Keywords: electrical resistivity ; enthalpy ; high temperature ; liquid alloys ; rhenium alloys ; specific heat ; thermal conductivity ; thermal diffusivity ; tungsten alloys
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Results are reported for the thermal conductivity and thermal diffusivity as a function of temperature for four W–Re alloys (4.0, 21.24, 24.07, and 31.09 mass% of Re) over a wide temperature range covering the solid and liquid states. The measurements allow the determination of specific heat and dependences among electrical resistivity, temperature, and density of the alloys into the liquid phase. The thermal conductivity is calculated using the Wiedeman–Franz law. Additionally, data for thermal conductivity and thermal diffusivity of the constituent elements, tungsten and rhenium, are presented for the first time. Both metals have been previously studied with the same experimental technique.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 20
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 1403-1415 
    ISSN: 1572-9567
    Keywords: HFC-32/125 ; HFC-32/134a ; binary mixture ; refrigerant ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The liquid thermal conductivity of mixtures of HFC-32/125 and HFC-32/134a was measured using the transient hot-wire apparatus in the temperature ranges from 213 to 293 K and from 193 to 313 K, respectively, in the pressure range from 2 to 30 MPa and with HFC-32 mass fractions of 0.249, 0.500, and 0.750 for each system. The uncertainty of the thermal conductivity was estimated to be ±0.7%. For practical applications, the thermal conductivity data for the two mixtures were represented by a polynomial in temperature, pressure, and mass fraction of HFC-32 with a standard deviation of 1.0%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 21
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 695-703 
    ISSN: 1572-9567
    Keywords: AC calorimetry ; CVD diamond film ; Debye phonon model ; grain boundary ; thermal conductivity ; thermal diffusivity ; U-process
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Diamond films 60 and 170 µm in thickness were grown by PACVD (plasma-assisted chemical vapor deposition) under similar conditions. The thermal diffusivity of these freestanding films was measured between 100 and 300 K using AC calorimetry. Radiation heat loss from the surface was estimated by analyzing both the amplitude and the phase shift of a lock-in amplifier signal. Thermal conductivity was calculated using the specific heat data of natural diamond. At room temperature, the thermal conductivity of the 60 and 170 υm films is 9 and 16 W-cm−1. K−1 respectively, which is 40–70% that of natural diamond, The temperature dependence of thermal conductivity of the CVD diamond films is similar to that of natural diamond, Phonon scattering processes are considered using the Debye model, The microsize of the grain boundary has a significant effect on the mean free path of phonons at low temperatures. The grain in CVD diamond film is grown as a columnar structure, Thus, the thicker film has the larger mean grain size and the higher thermal conductivity. Scanning electron microscopy (SEM) and Raman spectroscopy were used to study the microstructure of the CVD diamond films. In this experiment, we evaluated the quality of CVD diamond film of the whole sample by measuring the thermal conductivity.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 22
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 979-981 
    ISSN: 1572-9567
    Keywords: ceramics ; colloids composites ; conductivity ; pores ; resistivity ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Previous approximations for the effective conductivity of a matrix with inclusions of low conductivity, and for the effective resistivity of a matrix with inclusions of high conductivity, are combined to give the effective conductivity when both types of inclusions are present. This applies, for example, to a ceramic which contains both pores and metallic inclusions.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 23
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 267-273 
    ISSN: 1572-9567
    Keywords: high pressure ; thermal conductivity ; vitreous boron trioxide
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity, λ, of vitreous boron trioxide was measured, using a hot-wire procedure, from 170 to 570 K and under pressures of up to 1.7 GPa. The thermal conductivity at room temperature and zero pressure was found to be 0.52 W · m−1 · K−1. The values of the logarithmic pressure derivative, g = d(ln λ)/d(ln ρ), where ρ is the density, were found to be 1.1 for uncompacted glass and 0.7 for glass compacted to 1.2 GPa. The variation of λ with temperature at constant density was approximately linear, with a positive slope of 1.38×10−3W·m−1·K−2.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 24
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 379-389 
    ISSN: 1572-9567
    Keywords: energy conservation equations ; finite-element method ; high-thermal diffusivity fluids ; low-density measurements ; thermal conductivity ; transient hot-wire
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The measurement of the thermal conductivity of a fluid by means of the transient hot-wire technique so far has made use of an analytical solution of the energy conservation equation for an ideal model, coupled with a set of approximate analytical corrections to account for small departures from the model. For this solution to be valid, constraints were always imposed on the experimental conditions and the construction of the apparatus, resulting in an inability to measure the thermal conductivity of high-thermal diffusivity fluids. In this paper, the set of energy conservation equations describing the transient hot-wire apparatus is solved using the numerical finite-element method. Because no approximate solutions are involved, this provides a much more general treatment of the heat transfer processes taking part in the real experiment, removing all the aforementioned constraints. In the case of the measurement of the thermal conductivity of liquids (fluids with low thermal-diffusivity values), the numerical solution fully agrees with the existing analytical solution. In the case of the measurement of the thermal conductivity of gases, the present solution allows the extension of the application of the transient hot-wire technique to experimental conditions where the value of the thermal diffusivity of the fluid is high.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 25
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 455-466 
    ISSN: 1572-9567
    Keywords: aluminium/silicon carbide cermet ; aluminum/silicon eutectic ; plasma spray ; specific heat ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivities of three plasma-sprayed cermets have been determined over the temperature range 23–630°C from the measurement of the specific heat, thermal diffusivity, and density. These cermets are mixtures of Al and SiC prepared by plasma spray deposition and are being considered for various applications in magnetic confinement fusion devices. The samples consisted of three compositions: 61 vol% Al/39 vol% SiC, 74vol% Al/26vol% SiC, and 83 vol% Al/17 vol% SiC. The specific heat was determined by differential scanning calorimetry through the Al melt transition up to 720°C, while the thermal diffusivity was determined using the laser flash technique up to 630°C. The linear thermal expansion was measured and used to correct the diffusivity and density values. The thermal diffusivity showed a significant increase after thermal cycling due to a reduction in the intergrain contact resistance, increasing from 0.4 to 0.6 cm2·−1 at 160°C. However, effective medium theory calculations indicated that the thermal conductivities of both the Al and the SiC were below the ideal defect-free limit even after high-temperature cycling. The specific heat measurements showed suppressed melting points in the plasmasprayed cermets. The 39 vol% SiC began a melt endotherm at 577°C, which peaked in the 640–650°C range depending on the sample thermal history. Chemical and X-ray diffraction analysis indicated the presence of free silicon in the cermet and in the SiC powder, which resulted in a eutectic Al/Si alloy.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 26
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 663-673 
    ISSN: 1572-9567
    Keywords: corresponding states ; heavy water ; thermal conductivity ; water
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New measurements of the thermal conductivity of H2O and D2O have been performed from critical temperature up to 510°C and from atmospheric pressure up to 100 MPA. As these measurements have been made with the same cell, a precise analysis of the isotopic effect as a function of temperature and density is possible. Our analysis is presented in terms of corresponding states. It is shown that the critical thermal conductivity excesses for H2O and D2O reduced by their respective background thermal conductivity terms are represented by single reduced isotherms.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 27
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 731-742 
    ISSN: 1572-9567
    Keywords: specific heat ; thermal conductivity ; thermal diffusivity ; thermal emissivity ; thermophysical properties
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Various aspects of the importance of thermophysical property (TPP) studies to science and technology in China are discussed. Several stages of the development of experimental principles and equipment are described. Some examples of TPP applications in economic practice are presented. Theoretical and methodological studies in this field are summarized. The presentations are limited mostly to work on solids.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 28
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 273-284 
    ISSN: 1572-9567
    Keywords: alkanes ; hard-sphere theory ; hydrocarbons ; thermal conductivity ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The paper presents the results of a preliminary attempt to represent both the viscosity and the thermal conductivity of normal alkanes in the liquid phase by means of a mutually consistent scheme. The correlation method proposed is based upon the general results of the hard-sphere theory of dense fluids, although it does not make use of the detailed predictions of that model. It is shown that the viscosity of the alkanes, ethane, propane, n-butane, n-hexane, and n-octane may be represented by a single, universal function of reduced volume if each species is assigned a characteristic molar volume which is but weakly temperature dependent. Using the same values of molar volume the thermal conductivity of the same fluids can be represented by a further universal function of reduced volume by means of the choice of a second, temperatureindependent parameter.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 29
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 437-448 
    ISSN: 1572-9567
    Keywords: alkanes ; carbon dioxide ; diffusion ; mixtures ; molecular dynamics ; thermal conductivity ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Equilibrium molecular dynamics simulations of mixtures of n-decane with methane, ethane, and carbon dioxide and of the mixture carbon dioxide–ethane were performed using the anisotropic united atoms model for n-decane and one-and two-center Lennard–Jones models for the light components. The Green–Kubo relations were used to calculate the viscosity, thermal conductivity, and inter- and intradiffusion. Viscosities are predicted with a maximum deviation of 30% at low gas concentrations and less than 10% deviation at high gas concentrations. The viscosity and thermal conductivity are less sensitive to the cross interactions than the diffusion coefficients, which exhibit deviations between models and with experiments of up to 60%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 30
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 755-764 
    ISSN: 1572-9567
    Keywords: illite ; line-source probe ; sediment ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Results are reported for effective thermal conductivity measurements performed in situ and in core samples of illite marine sediment. The measurements were obtained during a recent oceanographic expedition to a study site in the north central region of the Pacific Ocean. This study was undertaken in support of the U.S. Subseabed Disposal Project, the purpose of which is to investigate the scientific feasibility of using the fine-grained sediments of the sea floor as a repository for high-level nuclear waste. In situ measurements were made and 1.5-m-long hydrostatic piston cores were taken, under remote control, from a platform that was lowered to the sea floor, 5844 m below sea level. The in situ measurement of thermal conductivity was made at a nominal depth of 80 cm below the sediment surface using a specially developed, line-source, needle probe. Thermal conductivity measurements in three piston cores and one box core (obtained several kilometers from the study site) were made on shipboard using a miniature needle probe. The in situ thermal conductivity was approximately 0.91 W · m−1 · K−1. Values determined from the cores were within the range 0.81 to 0.89 W · m−1 · K−1.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 31
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 765-772 
    ISSN: 1572-9567
    Keywords: cadmium arsenide ; electrical resistivity ; Hall effect ; low temperatures ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Results on electrical resistivity and thermal conductivity measured in the temperature range 4.2–40 K are presented for single-crystal and polycrystalline samples of Cd3As2. Hall effect has been studied at temperatures of 4.2, 77, and 300 K. The calculated value of the conduction electron concentration was in the range 1.87–1.95 1024m−3. Electrical resistivity of all investigated samples was independent of temperature up to about 10K and increased slowsly at higher temperatures. The thermal conductivity shows a maximum in the region in which the lattice component of thermal conductivity dominates. The strong anisotropy of the lattice component determines the anisotropy of the total thermal conductivity. The electronic component of thermal conductivity does not exhibit any anisotropy and shows a maximum at a temperature of about 300 K.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 32
    ISSN: 1572-9567
    Keywords: anisotropic materials ; pyrolytic graphite ; pyrolytic boron nitride ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The laser pulse method can be successfully applied to the measurement of thermal diffusivity of isotropic materials subject to some assumptions. For anisotropic materials, this method is applicable to the measurement of principal thermal diffusivity only on the condition that there is no difference in direction between the principal axis and that of the temperature gradient. After analyzing the heat conduction process in an anisotropic solid, it has been shown that large errors in the measurement of thermal diffusivity would exist if the direction of the principal axis deviates inconspicuously from that of the temperature gradient. The experimental results of thermal diffusivity of highly oriented pyrolytic graphite (HOPG) samples with various deviation angles have been compared with the analytical results. The laser pulse method is not applicable to measurements on semitransparent pyrolytic boron nitride (PBN). We adopted a two-layer composite sample to measure the thermal diffusivity of PBN in the c direction and a particular graphite-PBN composite sample has been prepared which has a very low thermal resistance at the interface. The thermal diffusivity and thermal conductivity of PG (below 2300°C) and PBN (below 1000°C) are given.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 33
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 607-620 
    ISSN: 1572-9567
    Keywords: high pressure ; hot-wire method ; thallium bromide (TlBr) ; thallium chloride (TlCl) ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The hot-wire method was used to measure the thermal conductivity of both TlCl and TlBr. The measurements were performed in the temperature range 120–300 K and at pressures up to 2.3 GPa. An analysis of the thermal conductivity data showed that the Leibfried-Schlömann formula is a better description for TlBr than for TlCl. For both TlBr and TlCl the effect of optic phonons on thermal conductivity cannot be ignored.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 34
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 39-46 
    ISSN: 1572-9567
    Keywords: Knudsen effect ; propane ; thermal conductivity ; thermal diffusivity ; transient line-source method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper decribes the Knudsen-effect errors of the transient line-source method used for accurate measurements of the thermal conductivity and thermal diffusivity of fluids. The analysis demonstrates that the instrument can be used with a good accuracy (〉0.5%) to lower densities than previously thought. The principal errors are illustrated by measurements on propane in the temperature range 250–300 K at densities less than 9 kg · m−3.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 35
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 21-35 
    ISSN: 1572-9567
    Keywords: heat capacity ; high pressure ; m-xylene ; o-xylene ; p-xylene ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New, absolute measurements of the thermal conductivity of the three xylene isomers within the temperature range 308–360 K for pressures up to 0.38 GPa are reported. In addition, for two of the isomers, m-xylene and p-xylene, it has been possible to measure the thermal diffusivity simultaneously within the same range of conditions. The accuracy of the thermal conductivity data reported is one of ±0.3%, whereas for the thermal diffusivity the estimated accuracy is ±6%. It is found that the density dependence of the thermal conductivity for all of the xylenes can be well represented by one equation based on a rigid-sphere model in the same way that has proved successful for normal alkanes. The thermal diffusivity data have been employed to derive heat capacities for the xylenes over a range of pressures.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 36
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 257-262 
    ISSN: 1572-9567
    Keywords: alloys ; germanium ; intermediate temperatures ; phonons ; point defects ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The lattice thermal conductivity is reduced by point defects because they scatter phonons. An analytic expression can be derived only in the limit of high temperatures; at lower temperatures one must have recourse to numerical calculations. Because the conductivity is due mainly to phonons of low frequencies when point-defect scattering is strong, the high-temperature approximation can be used at temperatures above half the Debye temperature. Numerical calculations, using the Ge-Si system as an example, show that the error incurred by using the high-temperature approximation is less than 10%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 37
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 283-292 
    ISSN: 1572-9567
    Keywords: critical range ; high pressure ; thermal conductivity ; steam
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New measurements of the thermal conductivity of steam have been performed in the temperature range 250–510°C and in the pressure range from 1 up to 95 MPa. Most of the measurements were taken at temperatures greater than the critical temperature, where the enhancement of the thermal conductivity is observed. The experimental values are compared to the IAPS formulation for the thermal conductivity of water.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 38
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 749-759 
    ISSN: 1572-9567
    Keywords: aqueous solutions ; capillary-rise method ; surface tension ; thermal conductivity ; transient hot-wire method ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Measurements of the surface tension, viscosity, and thermal conductivity of LiBr and LiSCN aqueous binary solutions have been performed to determine the thermophysical properties near the equilibrium freezing temperature. A differential capillary-rise method for surface tension and the transient hot-wire method for thermal conductivity were employed. Furthermore, a rotational viscometer was utilized for the measurement of viscosity. Correlation equations for the data of the aqueous binary test solutions as a function of temperature and concentration are presented.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 39
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 593-606 
    ISSN: 1572-9567
    Keywords: comparative technique ; Inconel 718 ; stainless steel ; standards ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The results of thermal conductivity measurements on Inconel 718 and 304 stainless steel by the comparative and flash diffusivity techniques are reported for the temperature range 0–700°C. For 304 stainless steel, excellent agreement with published data is found for the specific heat, thermal diffusivity, and thermal conductivity. In the case of Inconel 718, the measurements show that the conductivity depends critically on the sample thermal history and the metallurgical condition of the alloy. Measurements on a solution-treated sample indicated a conductivity function close to that reported previously, while precipitated samples showed a higher conductivity, similar to the conductivityvs-temperature function used for reduction of comparative thermal conductivity data with Inconel 718 references. These results indicate that Inconel 718 is not a suitable reference for high-accuracy comparative thermal conductivity measurements unless its thermal history and associated conductivity function are known.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 40
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 351-363 
    ISSN: 1572-9567
    Keywords: correlation ; n-alkanes ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of liquids has been shown in the past to be difficult to predict with a reasonable accuracy, due to the lack of accurate experimental data and reliable prediction schemes. However, data of a high accuracy, and covering wide density ranges, obtained recently in laboratories in Boulder, Lisbon, and London with the transient hot-wire technique, can be used to revise an existing correlation scheme and to develop a new universal predictive technique for the thermal conductivity of liquid normal alkanes. The proposed correlation scheme is constructed on a theoretically based treatment of the van der Waals model of a liquid, which permits the prediction of the density dependence and the thermal conductivity of liquid n-alkanes, methane to tridecane, for temperatures between 110 and 370 K and pressures up to 0.6 MPa, i.e., for 0.3⩽T/T c⩽0.7 and 2.4⩽P/P c⩽3.7, with an accuracy of ±1%, given a known value of the thermal conductivity of the fluid at the desired temperature. A generalization of the hard-core volumes obtained, as a function of the number of carbon atoms, showed that it was possible to predict the thermal conductivity of pentane to tetradecane±2%, without the necessity of available experimental measurements.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 41
    ISSN: 1572-9567
    Keywords: carbon dioxide ; high pressures ; mixtures ; nitrogen ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivities of nitrogen at 470 K and six mixtures of nitrogen and carbon dioxide at various temperatures have been measured as a function of pressure up to 25 MPa. The mixtures were measured at the following temperatures: one at 302 K, three at 380 K, one at 430 K, and one at 470 K. The data were used to test three prediction methods for the thermal conductivity of gas mixtures under pressure. Surprisingly good agreement was found with predictions using the corresponding-states method of Ely and Hanley. The predictions of the more theoretically based method of Mason et al. were low throughout, due partly to its use of the Hirschfelder-Eucken equation as the low-density limit, but also because the predicted density dependence rises too slowly. The simplified version of this method proposed by Svojskij gave slightly worse predictions, particularly at higher densities. The zero- density results for nitrogen are examined by comparing the zero-and first-density coefficients with the trends shown at lower temperatures.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 42
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 37-45 
    ISSN: 1572-9567
    Keywords: benzene ; thermal conductivity ; transient hot-wire technique ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New absolute measurements of the thermal conductivity of liquid benzene are reported. The measurements have been carried out in the temperature range 295–340 K, at atmospheric pressure, in a transient hot-wire instrument. The accuracy of the measurements is estimated to be ±0.5%. The measurements presented in this paper have been used, in conjunction with other high-pressure measurements of thermal conductivity and viscosity, to develop a consistent theoretically based correlation for the prediction of these properties. The proposed scheme permits the density dependence of the thermal conductivity and viscosity of benzene, for temperatures between 295 and 375 K and pressures up to 400 MPa, to be represented successfully by two equations containing just two parameters characteristic of the fluid at each temperature.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 43
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 933-940 
    ISSN: 1572-9567
    Keywords: alumina ; high temperature ; InSb ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of molten InSb in the temperature range between 800 and 870 K was measured by the transient hot-wire method using a ceramic probe. The probe was fabricated from a tungsten wire printed on an alumina substrate and coated with a thin alumina layer. The thermal conductivity was found to be about 18 W· m−·K−at the melting point and increased moderately with increasing temperature. The thermal conductivity of alumina used as the substrate for the probe was also measured in the same temperature range.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 44
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 923-931 
    ISSN: 1572-9567
    Keywords: high temperature ; KCl ; molten salts ; forced Rayleigh scattering method ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper describes measurement of the thermal diffusivity of molten KCl in the temperature range from 804 to 1030°C by the forced Rayleigh scattering method. In this contact-free optical measuring technique for the thermal diffusivity of liquids, a sample needs to be colored by the admixture of a dye for suitable absorption of a heating laser beam. The dye substances employed are CoCl2 and NiCl2, which were chosen through the experimental evaluation. The accuracy is estimated to be ±7% for molten KCl colored with NiCl2. The results converted to thermal conductivity show one of the smallest values among other previous data; the difference is a factor of four. The present study demonstrates the promising applicability of the forced Rayleigh scattering method to the measurement of high-temperature molten salts, which has never be attained by other conventional methods.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 45
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 267-277 
    ISSN: 1572-9567
    Keywords: diffusion ; liquid metals ; shear viscosity ; simple liquids ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Several simple approximate hard-sphere relations for transport coefficients are compared with the results of molecular dynamics (MD) simulations performed on Lennard–Jones (LJ) fluids. Typically the individual transport coefficients: self-diffusion coefficients, D, shear viscosity, ηs, bulk viscosity, ηB, and thermal conductivity, λ, agree within a factor of two of the exact results over the fluid and liquid parts of the phase diagram, which seems reasonable in view of the approximations involved in the models. We have also considered the ratio, λ/ηs, and the product, Dηs, for which simple analytic expressions exist in the hardsphere models. These two quantities also agree within a factor of two of the simulation values and hard sphere analytic expressions. Using time correlation functions, Tankeshwar has recently related the ratio λ/D to thermodynamic quantities, in particular, to the differences in specific heats, C p − C V, and to the isothermal compressibility, κT. Using D and thermodynamic values taken solely from LJ MD simulations, his relation was tested and found to give typically better than ~20% agreement at liquid densities, deteriorating somewhat as density decreases into the gas phase. Finally liquid metals are considered. In this case, λ is dominated by its electronic contribution, which is related approximately to the electrical conductivity by the Wiedemann–Franz Law. Some theoretical results for the electrical conductivity of Na are referenced, which allow a semiquantitative understanding of the measured thermal conductivity of the liquid metal. Shear viscosity is also discussed and, following the work of Tosi, is found to be dominated by ionic contributions; Nevertheless, at the melting temperature of Na, a relation emerges between thermal conductivity, electrical resistivity and shear viscosity.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 46
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 315-330 
    ISSN: 1572-9567
    Keywords: coaxial cylinder method ; mixing rule ; mixtures ; molten salts ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of some molten salts was measured at atmospheric pressure, using the coaxial cylinder method. The pure compounds NaCO3, KNO3, and NaNO2, the equimolar mixture NaNO3-KNO3, and HITEC, which is a three-component mixture, NaNO3-NaNO2-KNO3 (0.07-0.40-0.53 in weight), were investigated. For mixtures, it was found that the experimental thermal conductivity coefficients are in agreement with calculated values using a simple linear mixing law. The thermal diffusivity was calculated and compared with experimental data.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 47
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 133-144 
    ISSN: 1572-9567
    Keywords: Enskog theory ; equation of state ; fluids (dense) ; thermal conductivity ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract An attempt is made in this work to combine the Enskog theory of transport properties with the simple cubic Peng-Robinson (PR) equation of state. The PR equation of state provides the density dependence of the equilibrium radial distribution function. A slight empirical modification of the Enskog equation is proposed to improve the accuracy of correlation of thermal conductivity and viscosity coefficient for dense gases and liquids. Extensive comparisons with experimental data of pure fluids are made for a wide range of fluid states with temperatures from 90 to 500 K and pressures from 1 to 740 atm. The total average absolute deviations are 2.67% and 2.02% for viscosity and thermal conductivity predictions, respectively. The proposed procedure for predicting viscosity and thermal conductivity is simple and straightforward. It requires only critical parameters and acentric factors for the fluids.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 48
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 1041-1051 
    ISSN: 1572-9567
    Keywords: alkanes ; mixtures ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper reports new, absolute measurements of the thermal conductivity of liquid mixtures of n-heptane and isooctane in the pressure range 0.1 to 430 MPa for temperatures of 307.85 and 337.15 K. The results represent a preliminary investigation of the advantages of attempting to describe the isothermal composition dependence of the thermal conductivity of liquid mixtures along isochores, rather than isobars as has been traditional. However, no significant differences were found between the composition dependences in the two circumstances, possibly due to the lack of experimental data on the density of these mixtures. The availability of a theoretical description of the isochoric composition dependence suggests that this is the most appropriate description which reinforces the need for further high-pressure measurements of the thermal conductivity and density.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 49
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 1075-1084 
    ISSN: 1572-9567
    Keywords: aluminum nitride ; heat capacity ; substrate ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal transport properties of four commercially available AlN substrates have been investigated using a combination of steady-state and transient techniques. Measurements of thermal conductivity using a guarded longitudinal heat flow apparatus are in good agreement with published room temperature data (in the range 130–170 W · m−1 · K−1). Laser flash diffusivity measurements combined with heat capacity data yielded anomalously low results. This was determined to be an experimental effect for which a method of correction is presented. Low-temperature measurements of thermal conductivity and heat capacity are used to probe the mechanisms that limit the thermal conductivity in AlN.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 50
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 1005-1011 
    ISSN: 1572-9567
    Keywords: benzene ; thermal conductivity ; toluene ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of liquid toluene and benzene was measured in the temperature range 298 to 370 K, near the saturation line, using an absolute transient hot-wire technique. The measurements were made in a modified version of an existing instrument, equipped with a new automatic Wheatstone bridge, computer controlled. The bridge measures the time that the resistance of a 7-μm-diameter platinum wire takes to reach predetermined values, programmed by the computer. The computer can generate up to 1024 analog voltages, via a 12-bit D/A converter. The accuracy of the measurements with this new arrangement was assessed by measuring the thermal conductivity of a primary standard, toluene, at several temperatures and was found to be of the order of 0.3%. Benzene was chosen because it is under study as a possible secondary standard for liquid thermal conductivity by the Subcommittee on Transport Properties of IUPAC.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 51
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 10 (1989), S. 1053-1062 
    ISSN: 1572-9567
    Keywords: alumina ; composites ; glass ; porosity ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal diffusivity of five groups of alumina/glass composite systems has been measured at room temperature using a laser flash system. These data have been used, in conjunction with specific heat and density measurements, to calculate the effective thermal conductivity of these composites. In each of the five groups a systematic variation in glass concentration was made, and each group represents systematic variations in glass and alumina particle sizes. The thermal conductivities calculated are compared with those predicted by four models. It is apparent from these comparisons that the geometry and orientation of porosity within the sample measured are a key factor in determining which of these models (if any) is appropriate for describing the thermal conductivity of these composites.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 52
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 195-204 
    ISSN: 1572-9567
    Keywords: ethane ; gas metering ; methane ; natural gas ; prediction ; thermal conductivity ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The evaluation of the background transport properties of natural gas multicomponent mixtures over a moderate temperature and pressure range around ambient is considered in the context of the development of certifiable sensors for the measurement of mass and energy fluxes. The best available, theoretically based procedures to predict the properties are compared with experimental information to test the internal consistency, accuracy, and range of validity of the prediction. This is of primary concern to the demonstration of the viability of such sensors. It is shown that for low to moderate pressures, it is possible to achieve an internal consistency of the order of a few parts in a thousand and an accuracy of better than ± I %. At very high pressures the predictive scheme is also satisfactory, with errors of the order of a few percent. However, the procedure employed here systematically underestimates the thermal conductivity of the gas mixtures studied for intermediate pressures owing to the neglect of the critical enhancement even for temperatures quite far removed from the critical. The range of conditions for which the critical enhancement of the thermal conductivity is significant in mixtures is explored with data for binary mixtures of methane and ethane.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 53
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 821-829 
    ISSN: 1572-9567
    Keywords: a.c. calorimetry ; fluctuation effects ; specific heat ; superconductors ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The specific heat and thermal conductivity measurements of YBa2Cu3O7−δ high-T c superconductors were performed by an a.c. calorimetry method. Investigations of the specific heat of YBa2Cu3O7−δ ceramics in magnetic fields show that an increase in the magnetic field reduces the jump in the specific heat, broadens the transition region, and shifts the transition temperature downward by about 0.5 K, Temperature dependence of the specific heat of a YBa2Cu3O7−σ high-T c superconducting ceramic reveals that fluctuation affect the specific heat near the superconducting transition, Critical exponentsα =α′ = 0.5, the critical amplitudesC + =C − = 0.5 J · mol−1 K−1, the space dimensionalityd = 3, and the number of components in the order parametern = 3 is calculated, The specific heat and the along-c-axis thermal conductivity of YBa2Cu,3O7−δ single crystal were simultaneously measured.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 54
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 121-131 
    ISSN: 1572-9567
    Keywords: dilluoromethane ; hydrolluorocarbon ; HFC-32 ; HFC-125 ; pentalluoroethane ; refrigerant ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The gaseous thermal conductivity of dilluoromethane (HFC-32). pentalluoroethane (HFC-125). and their binary mixtures was measured with a transient hot-wire apparatus in the temperature ranges 283–333 K at pressures up to saturation. The uncertainty of the data is estimated to be within I %. The thermal conductivity as a function of composition of the mixtures at constant pressure and temperature is found to have a small maximum near 0.3–0.4 mole fraction of HFC-32. The gaseous thermal-conductivity data obtained for pure HFC-32 and HFC-125 were correlated with temperature and density together with the liquid thermal-conductivity data from the literature, based on the excess thermal-conductivity concept. The composition dependence of the thermal conductivity at a constant temperature is represented with the aid of the Wassiljewa equation.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 55
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 237-244 
    ISSN: 1572-9567
    Keywords: critical phenomena ; mixtures ; 2-n-butoxyelhanol ; thermal conductivity ; transient hot-wire ; water
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of binary liquid mixtures of water and 2-n-butoxyethanol has been measured within the temperature range 305–350 K at pressures up to 150 MPa. The measurements have been carried out with a transient hotwire instrument suitable for electrically conducting liquids and have an estimated accuracy of ±0.3%. The liquid mixture has a closed-loop solubility and reveals a lower critical solution temperature for a mole fraction of 2-n-butoxyethanol of 0.0478 at a temperature of 322.25 K. The results of the measurements reveal a small, but discernible, enhancement of the thermal conductivity of the solution at the critical composition.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 56
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1069-1086 
    ISSN: 1572-9567
    Keywords: flow anisotropy ; forced Rayleigh scattering ; molten salts ; optical method ; polymers ; shear anisotropy ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The experimental determination of thermophysical properties has been greatly improved by the introduction of laser technology. The laser beam is used for sensing and also for heating (or exciting) the specimen. The advantage of using a laser beam is most strongly felt in the measurement of the thermal conductivity or the thermal diffusivity, which are some of the most difficult properties to measure. Interesting features of new techniques for investigating various aspects of thermal conductivity in fluids and solids are reviewed. An optical method, the so-called forced Rayleigh scattering method, or the laser-induced optical-grating method, has been developed and used extensively by the present author's group. The method is a high-speed remote-sensing method which can also quantitatively detect anisotropy, namely, direction dependence of heat conduction in the material. It was used for determination of the thermal diffusivity and its anisotropic behavior for high-temperature materials such as molten salts, liquid crystals, extended polymer samples, and flowing polymer melts under shear. Interesting applications of the method were demonstrated also for thermal diffusivity “mapping” and microscale measurement.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 57
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 761-772 
    ISSN: 1572-9567
    Keywords: density ; high pressure ; refrigerants ; Tail equation ; thermal conductivity ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A recently developed scheme, based on considerations of hard-sphere theory, is used for the simultaneous correlation of the coefficients of viscosity and thermal conductivity for the refrigerants R11, R12, R22, R32. R124, R125, R134a, R141b, and R152a in excellent agreement with experiment, over extended temperature and pressure ranges. Values for the roughness factors and correlations for the characteristic volume are presented. The overall average absolute deviations of the experimental viscosity and thermal conductivity measurements from those calculated by the correlation are 2.1 and 2.3%, respectively, over a temperature range from 200 to about 10 K below the critical temperature and a pressure range from saturation to about 40 MPa. Since the proposed scheme is based on recent and accurate density values, a Tail-type equation was also employed to correlate successfully the density of the refrigerants. The overall average absolute deviation of the experimental density measurements from those calculated by the correlation is ±0.08%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 58
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 851-865 
    ISSN: 1572-9567
    Keywords: high pressure ; refrigerants ; R32 ; R124 ; R125 ; R141b ; thermal conductivity ; transient hot-wire technique
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper reports measurements of the thermal conductivity of refrigerants R32, R124, R125, and R141b in the liquid phase. The measurements, covering a temperature range from 253 to 334 K and pressure up to 20 MPa, have been performed in a transient hotwire instrument employing two anodized tantalum wires. The uncertainty of the present thermal-conductivity data is estimated to be ±0.5%. The experimental data have been represented by polynomial functions of temperature and pressure for the purposes of interpolation. A comparison with other recent measurements is also included.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 59
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1193-1201 
    ISSN: 1572-9567
    Keywords: R134a, R32 ; R32+R134a mixture ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The liquid thermal conductivity of R32 (CH2F2) and R134a (CF3CH2F) was measured in the range from 223 to 323 K and from 2 to 20 MPa by the transient hot-wire method. The thermal conductivity of the R32+R134a mixture was also measured in the same range by varying the mass fraction of R32. The measured data are analyzed to obtain a correlation in terms of temperature, pressure and composition of the mixture. The uncertainty of our measurements is estimated to be within ±2%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 60
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1203-1211 
    ISSN: 1572-9567
    Keywords: guarded hot-plate apparatus ; polar refrigerant ; R22 ; R123 ; R134a ; R142b ; R143a ; R152a ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of the refrigerants R22, R123, R134a, R142b, R143a, and R152a has been determined as a function of temperature in the range from 300 to 460 K. Measurements were carried out at atmospheric pressure with an improved guarded hot-plate apparatus. The width of the instrument's gas layer and the temperature difference across the metering section were varied to detect any stray heat transfer. Radiation correction factors were derived from IR absorption spectra. The uncertainty of the measurements is estimated to be 2% at a standard deviation of less than 0.1%. All values are correlated with respect to temperature in the range covered. The equations are found to represent the results with average deviations of 1%. Our data sets are compared with corresponding hot wire results. In contrast to the generally preferred hot wire technique, with its possible electrical and chemical interactions between the wire and the polar refrigerant, there are no such difficulties using a guarded hot-plate apparatus. Our data sets may thus contribute to the discussions on discrepancies in thermal conductivity values from various authors using hot wire as one particular method.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 61
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1353-1361 
    ISSN: 1572-9567
    Keywords: aqueous solutions ; diffraction ; ethanol ; laser-induced thermal grating ; methanol ; scattering ; thermal conductivity ; thermal diffusivity ; water
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal diffusivity of methanol, ethanol, and their aqueous solutions was measured at atmospheric pressure and temperature. The measurements were performed with a laser-induced thermal grating technique. The aqueous solutions have weight fractions of 20, 40, 60, and 80%. Systematic errors were taken into consideration, and corrections were made to the measured values. Focused laser beams were used, which notably intensify the diffracted signal, reduce the background to zero, and justify neglecting the heterodyne term of the diffracted signal, thus simplifying the data evaluation. Hence, the accuracy of the measurements was improved significantly. The overall accuracy of the measurements is estimated to be better than 1.5%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 62
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1455-1466 
    ISSN: 1572-9567
    Keywords: heat of fusion ; sodium acetate hydrate ; specific heat capacity ; supercooled liquid ; thermal conductivity ; thermistor
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Methods to measure the thermal conductivity, the specific heat capacity, and the heat of fusion of sodium acetate hydrate have been developed and the measured results have been reported for various concentrations and especially for various supercooling temperatures. Thermal conductivity was measured by using a probe method with a thermistor. The sensor element is very small, with a diameter of 0.5 mm and a length of 1.5 mm. Data for both the ordinary liquid and the supercooled liquid are smoothly connected to each other.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 63
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 16 (1995), S. 1481-1487 
    ISSN: 1572-9567
    Keywords: electrical resistivity ; high temperature ; thermal conductivity ; oxidation ; zirconium
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity and electrical resistivity of zirconium-1 wt% niobium samples were measured before and after the process of their oxidation in air. A special procedure was used to dissolve the gas and to smooth out its concentration in the alloy. The basic experiments were performed under high vacuum under steady-state temperature conditions. The temperature range was 300–1600 K. for the pure alloy and 300–1100 K for the samples containing oxygen. It was found that the thermal conductivity—oxygen concentration relation reverses its sign from negative at low and middle temperatures to positive at temperatures above 900 K. The relation between the electrical resistivity and the oxygen content does not show this feature. The Lorenz function was found to have an anomalous temperature dependence.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 64
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 85-98 
    ISSN: 1572-9567
    Keywords: halocarbon refrigerants ; mixtures ; prediction method ; pure fluids ; saturated liquid state ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A prediction method for the thermal conductivity of halocarbon refrigerants in the saturated liquid state in the reduced temperature range 0.3 to well above 0.9 is presented in this paper. The aim of the method is to present a very simple calculation of the transport property useful for engineering purposes. The method determines thermal conductivity as a sole function of the reduced temperature and requires the knowledge of a parameter dependent upon easily available physical constants characteristic of each compound. The method is validated against experimental data available in the literature, giving average absolute deviations which are usually less than 5%, with maximum absolute deviations generally less than 10%. An extension of the method to estimate thermal conductivity of binary mixtures is also presented, along with a comparison with the few experimental data available in the literature.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 65
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 239-252 
    ISSN: 1572-9567
    Keywords: metal matrix composites ; thermal conductivity ; titanium
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Thermal conductivity data are presented for titanium-based composites reinforced with 10 and 20%, by volume, of SiC and TiB2 particles and for a composite reinforced by 10%, by volume, of SiC short fibers. In each case the thermal conductivity of titanium would be expected to be enhanced by the presence of the reinforcement. Measurements were made on the composites both as fabricated and after heat treatment. The results clearly show that the thermal conductivity of the Ti-SiC is much lower than predicted and decreases still further after heat treatment. This is attributed to the production of an interfacial contact resistance as a result of crack generation in the reaction products. A smaller effect is noted in the Ti-TiB2 composites.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 66
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 253-261 
    ISSN: 1572-9567
    Keywords: flash method ; melts ; radiation correction ; slags ; three-layer analysis ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A high-temperature measuring system has been developed to undertake measurements of thennal difusivity and specific heat up to 1900 K. The overall design allows measurements on solids to be undertaken using the accepted standard techniques and analytical procedures. The specific design for molten materials and especially slags is based on the differential threelayer technique utilizing a special cell which can be accomodated in the system. In this method, the liquid specimen is sandwiched between an upper inner platinum crucible and a lower outer platinum crucible, to provide a three-layered sandwich. A laser pulse irradiates the surface of the upper platinum crucible and the temperature response of the surface of the lower platinum crucible is observed. For the purpose of accurate measurement of specimen thickness at the measuring temperature, two runs are performed in which the thicknesses arel andl+°Dl, wherel is unknown butΔl can be set accurately with a built-in micrometer. The thermal difusivity is obtained through a curve-fitting method by a personal computer using a three-layer analysis with a correction for the radiative component based on the transparent body assumption. Following verification of the basic performance, using solids of known properties and water and ethanol, a continuous casting mixture has been evaluated. The initial results on the fluids are in good agreement with those in the literature.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 67
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 279-292 
    ISSN: 1572-9567
    Keywords: CFC-alternatives ; HCFC-141b ; HFC-125 ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The liquid thermal conductivities of the CFC alternatives, HFC-125, and HCFC-141b measured by a transient hot-wire apparatus with one bare platinum wire are reported in the temperature ranges from 193 to 333 K (HFC-125, CHF2, CF3) and from 193 to 393 K (HCFC-141b,CCI2F-CF3), in the pressure ranges from 2 to 30 MPa (HFC-125) and from 0.1 to 30 MPa (HCFC-141b), respectively. The results have been estimated to have an accurancy of ±0.5%. The liquid thermal conductives obtained have been correlated by a polynomial of temperature and pressure which can represent the experimental results within the standard deviations of 0.49% for HFC-125 and 0.46% for HCFC-141b, respectively.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 68
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 293-328 
    ISSN: 1572-9567
    Keywords: 2,2-dichloro-1,1,1-trifluoroethane ; HCFC-123 ; R123 ; thermal conductivity ; thermal diffusivity ; transport properties ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity and the viscosity data of CFC alternative refrigerant HCFC-123 (2,2-dichloro-1,1,1-trifluoroethane: CHCI2-CF3) were critically evaluated and correlated on the basis of a comprehensive literature survey. Using the residual transport-property concept, we have developed the three-dimensional surfaces of the thermal conductivity-temperature-density and the viscosity-temperature-density. A dilute-gas function and an excess function of simple form were established for each property. The critical enhancement contribution was taken no account because reliable crossover equations of state and the thermal conductivity data are still missing in the critical region. The correlation for the thermal conductivity is valid at temperatures from 253 to 373 K, pressures up to 30 MPa, and densities up to 1633 kg m−3. The correlation for the viscosity is valid at temperatures from 253 to 423 K, pressures up to 20 MPa. and densities up to 1608 kg·m−3. The uncertainties of the present correlations are estimated to be 50% for both properties, since the experimental data are still scarce and somewhat contradictory in the vapor phase at present.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 69
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 733-742 
    ISSN: 1572-9567
    Keywords: calorimetry ; diffusivity ; emissivity, heat capacity ; radiant exchange ; simultaneous measurement ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Thermal radiation calorimetry has been applied to measure the thermal diffusivity of a solid specimen, along with simultaneous measurements of specific heat capacity and thermal conductivity. In this calorimeter, a disk-shaped solid specimen whose surfaces are blackened is heated and cooled slowly on one face by irradiation in a vacuum chamber. A quasi-steady-state approximation in which a linear temperature gradient within the specimen was assumed is considered in the analysis. The validity of this approximation was confirmed by the results of computer simulation based on the control-volume method. Measurements of Pyroceram 9606 and Pyrex 7740 by use of thermocouples in the temperature range between 250 and 400°C gave values consistent with those obtained by previous authors, within experimental error, for all three thermophysical properties.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 70
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 977-986 
    ISSN: 1572-9567
    Keywords: ac calorimetry ; CVD diamond ; modified Angstrom method ; reference materials ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Modified ac calorimetry, a variation of the Angstrom method, has been shown to be a precise tool for measuring the in-plane thermal diffusivity of thin films (thickness less than 300 μm) of a wide variety of materials and layered composites. The property is determined from an analysis of the decay curve of the ac temperature waves generated by irradiation of a specimen using uniform chopped light (at frequencies from 1 to 20 Hz) from a halogen lamp source. To address certain limiting factors, especially to improve the signal-to-noise ratio and to eliminate heat losses, an improved form of measurement instrument has been developed. It is based on the use of a modulated laser beam heating to provide a higher intensity energy source plus a special optical system to ensure that one-dimensional ac temperature wave propagation is obtained. Measurements can now be made using frequencies in the range of 0.01 to 10 Hz, i.e., 10 times lower than in the traditional method. The performance of the improved measurement instrument will be illustrated by results on various materials of known thermal properties such as nickel and stainless steel, proposed reference materials such as a glassy carbon and alumina, plus a comparison of results obtained on CVD diamond films used in an international round-robin series with those obtained by the traditional technique.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 71
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 1051-1060 
    ISSN: 1572-9567
    Keywords: copper ; liquid metals ; liquid alloys ; Lorenz relation ; resistivity ; thermal conductivity ; thermal diffusivity ; tin
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal properties (heat capacity, thermal diffusivity, and electrical resistivity) of a Cu + 10 wt% Sn alloy in both solid and liquid phases have been reported. Using these values it was confirmed that the Lorenz relation is suitable for obtaining thermal conductivity from electrical resistivity in the liquid phase of this alloy. Also, the temperature differential (dλ/dT) obtained from such an approach was in excellent agreement with the thermal conductivity values calculated from thermal diffusivity.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 72
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 1279-1288 
    ISSN: 1572-9567
    Keywords: compressibility ; electrical conductivity ; emissivity ; specific heat ; thermal conductivity ; thermal expansion coefficient ; tungsten
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Wire explosion experiments were used to obtain thermophysical properties of tungsten. These properties are specific heat, thermal expansion coefficient, compressibility, and electrical and thermal conductivities and their dependences on temperature. There are strong indications that the emissivity in the liquid range should be dependent on temperature. A proposal has been made for determining the emissivity from comparison of experiments with model calculations. The temperature range is extended up to 10,000 K, and first indications for the near-critical-point behavior were obtained. Other properties such as diffusivity, viscosity, and surface tension may possibly also be derived in this range.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 73
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 17 (1996), S. 731-757 
    ISSN: 1572-9567
    Keywords: 1,1-difluoroethane ; correlation ; critical region ; HFC-152a ; R152a ; thermal conductivity ; transport properties ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Based on reliable. carefully selected data sets. equations for the thermal conductivity and the viscosity of the refrigerant R 112a are presented. They are valid at temperatures from 240 to 440 K, pressures up to 20 MPa. and densities up to 1050 kg · m−3. including the critical region.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 74
    ISSN: 1572-9567
    Keywords: photothermal radiometry ; roughness effects ; thermal-sprayed coatings ; thermal diffusivity ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Laser infrared photothermal radiometry (PTR) was used to measure the thermophysical properties (thermal diffusivity and conductivity) of various thermal sprayed coatings on carbon steel. A one-dimensional photothermal model of a three-layered system in the backscattered mode was introduced and compared with experimental measurements. The uppermost layer was used to represent a roughness-equivalent layer, a second layer represented the thermal sprayed coating, and the third layer represented the substrate. The thermophysical parameters of thermal sprayed coatings examined in this work were obtained when a multiparameter-fit optimization algorithm was used with the backscattered PTR experimental results. The results also suggested a good method to determine the thickness of tungsten carbide and stainless-steel thermal spray coatings once the thermophysical properties are known. The ability of PTR to measure the thermophysical properties and the coating thickness has a strong potential as a method for in situ characterization of thermal spray coatings.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 75
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 1653-1666 
    ISSN: 1572-9567
    Keywords: critical parameters ; dielectric constant ; difluoromethane ; dipole moment ; heat capacities ; HFC-32 ; pvT behavior ; refractive index ; saturation densities ; second virial coefficient ; speed of sound ; surface tension ; survey ; thermal conductivity ; vapor pressure ; viscosity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A survey of experimental data for HFC-32 was prepared at the Institute of Thermomechanics in connection with planned experiments. In tabular form, surveys of thermodynamic, transport, and other property measurements, including pvT behavior, second virial coefficient, vapor pressure, saturation densities, critical parameters, heat capacities, speed of sound, thermal conductivity, viscosity, surface tension, refractive index, dielectric constant, and dipole moment, are presented. Tables include author)s) name(s), reference, year of publication, ranges of measurements, number of points, stated uncertainty, sample purity, and experimental method.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 76
    ISSN: 1572-9567
    Keywords: cobalt ; electrical resistivity ; low temperatures ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Thermal conductivity and electrical resistivity of 99.99% pure Co sample were measured in the temperature range 2.5–30 K. The annealing, procedure of the sample (either above or below Curie temperature), followed by cooling it down to room temperature at a slow cooling rate, caused an unexpected increase in its thermal resistivity and residual electrical resistivity, contrary to the results obtained for most pure metals. Co samples either not thermally treated or annealed consist only of a HI phase as proved by X-ray and electron diffraction analyses. The result, led to the conclusion that changes of grain structure and physical defects appearing in the Co at Curie temperature and at 690 K, when phase transitions take place, should be taken into account. The electron-magnon scattering, is significant in electrical conductivity but the electron-physical defect and impurity scattering plays a dominant role in thermal conductivity. The electron-physical defect and impurity scattering is elastic (validity of the Wiedemann Franz law)) as demonstrated by the value ofβ th β el = 1.0, obtained in this work.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 77
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 15-25 
    ISSN: 1572-9567
    Keywords: aqueous solution ; diffraction ; laser-induced thermal grating ; sodium chloride ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The laser-induced thermal grating technique was used to determine the thermal diffusivity of aqueous solutions of sodium chloride. In comparison with conventional measurement methods, this noninvasive optical technique has the advantage that no sensors need to be inserted in the sample. Therefore, this technique is especially suitable for the measurement of electrically conducting and corrosive liquids. The aqueous solutions studied have weight fractions of 5, 10, 15, and 20% sodium chloride. Measurement results for the thermal diffusivity are presented for aqueous solutions of sodium chloride in the temperature range 293 to 373 K at atmospheric pressure.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 78
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 3-20 
    ISSN: 1572-9567
    Keywords: argon mixture ; carbon tetrafluoride mixtures ; helium mixture ; statistical mechanics ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The paper presents new measurements of the thermal conductivity of the binary mixtures of carbon tetrafluoride with helium and argon. Measurements were performed in a transient, hot-wire instrument at a nominal temperature of 27.5°C and over a range of densities (pressure up to 12 MPa). The accuracy is estimated to be 0.4%, deteriorating to 0.7% around the critical density. The paper provides polynomial fits which represent the data with a standard deviation of 0.4%. An analysis in terms of the Monchick-Pereira-Mason theory, with the translational contributions computed on the basis of earlier measurements of the viscosity of these mixtures, leads to a reasonable representation of the composition dependence of the zero-density thermal conductivity; the collision numbers ζ ij are treated here as adjustable parameters to obtain an optimum fit for each mixture.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 79
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 177-190 
    ISSN: 1572-9567
    Keywords: heat capacity ; high pressure ; sodium bromide (NaBr) ; thermal conductivity ; thermal expansivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Using the transient hot-wire method, measurements were made for solid NaBr of both the thermal conductivity and the heat capacity per unit volume. The measurements were performed in the temperature range 100 to 400 K and at pressures up to 2 GPa. An adiabatic compression technique allowed the determination of the thermal expansivity as a function of pressure at room temperature. The heat capacity did not vary with pressure. Analysis of the thermal conductivity data showed that it can be described adequately by the Leibfried-Schlömann formula. For temperatures up to 400 K only acoustic modes needed to be taken into account. A small contribution of optic modes to the heat transport might be apparent at the highest temperatures.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 80
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 251-265 
    ISSN: 1572-9567
    Keywords: alkanes ; hydrocarbons ; liquids ; mixing rule ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity of four pure normal paraffin hydrocarbons (C11, C14, C15, C16) and binary and ternary mixtures of three n-paraffin hydrocarbons (C7, C11, C16) have been measured in the temperature range from about 20 to 90°C at atmospheric pressure. Measurements have been performed with the aid of a fully automated transient hot-wire instrument. The accuracy of the reported data is estimated to be ±1.0 to ±1.5%. A new simple and practical equation, which can calculate the thermal conductivity of pure n-paraffin hydrocarbons (4≤n≤ 16) with the uncertainty of ±1%, has been correlated in terms of temperature and number of carbon atoms based on the present results including some other reliable data. Also, a mixing rule for the mixtures of n-paraffin hydrocarbons was proposed and was adequately confirmed by the present results within the experimental error.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 81
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 6 (1985), S. 353-365 
    ISSN: 1572-9567
    Keywords: high pressure ; sodium fluoride (NaF) ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity (λ) of solid NaF has been measured over the temperature (T) range 100–350 K and at pressures (P) up to 2.5 GPa, using the transient hot-wire method. Results for λ(T,P) could be described to a good approximation by the Leibfried-Schlömann formula. It was found that the isochoric temperature derivative of the thermal resistivity W (= λ−1) increased systematically with the mass ratio for the B1-type phases of the sodium and potassium halides.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 82
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 7 (1986), S. 181-195 
    ISSN: 1572-9567
    Keywords: high temperatures ; pulse heating ; specific heat ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A method for the simultaneous measurement of thermal diffusivity and specific heat by a single rectangular heating pulse on a finite cylindrical specimen is described. The method takes into account radiation losses from all the surfaces of the specimen. The theoretical principle of the technique was studied by solving the transient heat conduction equation for a finite disk heated on the front surface by a single rectangular radiant energy pulse. An apparatus was constructed to comply with the theoretical conditions and was connected to a personal computer. Thermal diffusivity and specific heat were determined from the data obtained on the temperature response of the back surface of the specimen and from the theoretical results. This method can be applied to materials having a wide range of thermal conductivity values and has a good accuracy at high temperatures. Examples of the measurements are presented.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 83
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 415-425 
    ISSN: 1572-9567
    Keywords: HFC-32 ; HFC-125 ; HFC-134a ; melting point ; refrigerant ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Measurements of the thermal conductivity of HFC-32, HFC-125, and HFC-134a were carried out for the first time in both solid and liquid phases at the saturation pressure at room temperature and in the temperature ranges from 120 to 263, from 140 to 213, and from 130 to 295 K, respectively. A transient hot-wire instrument using one bare platinum wire was employed for measurements, with an uncertainty of less than ±2%. The experimental results demonstrated that the thermal conductivity of HFC-32, HFC-125, and HFC-134a in the solid phase showed a positive temperature dependence. For HFC-32 and HFC-125, there were big jumps between the solid and the liquid thermal conductivity at the melting point. But for HFC-134a, the solid and liquid thermal conductivity at the melting point is almost-continuous.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 84
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 511-523 
    ISSN: 1572-9567
    Keywords: chemical vapor deposition (CVD) diamond ; phonon scattering ; specific heat ; thermal conductivity ; thermal diffusivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The thermal conductivity κ of natural, gem-quality diamond, which can be as high as 2500 Wm−1 K−1 at 25°C, is the highest of any known material. Synthetic diamond grown by chemical vapor deposition (CVD) of films up to 1 mm thick exhibits generally lower values of κ but under optimal growth conditions it can rival gem-quality diamond with values up to 2200 Wm−1 K−1. However, it is polycrystalline and exhibits a columnar microstructure. Measurements on free-standing CVD diamond, with a thickness in the range 25–400 μm, reveal a strong gradient in thermal conductivity as a function of position z from the substrate surface as well as a pronounced anisotropy with respect to z. The temperature dependence of κ in the range 4 to 400 K has been analyzed to determine the types and numbers of phonon scattering centers as a function of z. The defect structure, and therefore the thermal conductivity, are both correlated with the microstructure. Because of the high conductivity of diamond, these samples are thermally thin. For example, laser flash data for a 25-μm-thick diamond sample is expected to be virtually the same as laser flash data for a 1-μm-thick fused silica sample. Several of the techniques described here for diamond are therefore applicable to much thinner samples of more ordinary material.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 85
    ISSN: 1572-9567
    Keywords: anisotropic scattering ; fibers ; insulations ; low-pressure CVD ; low temperatures ; Mie theory ; scaled diffusion law ; spectral extinction coefficient ; thermal conductivity ; totally reflecting fibers
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract This paper describes first experimental steps of an attempt to replace evacuated multifoils by metal-coated dielectric fibers as a new superisolation. Calculations of the Rosseland mean of spectral extinction coefficients for thin highly relective fibers show that radiation transport can be reduced to the same extent that is achievable with multifoils. Experimental results of extinction coefficients and thermal conductivity of Al-coated glass fibers are reported. Apparently, the metal coating does not increase seriously the small solid thermal conductivity of pure glass fibers. The procedure for optimizing this insulation is thus reduced to an optimization of its extinction properties.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 86
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 293-304 
    ISSN: 1572-9567
    Keywords: critical region ; ethane ; high pressure ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A coaxial cylinder method was used to measure the thermal conductivity of ethane in the pressure range from 10 up to 280 bar and in the temperature range from 308 up to 365 K.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 87
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 317-333 
    ISSN: 1572-9567
    Keywords: air ; argon ; helium ; hot-plate apparatus ; hydrogen ; impurities ; krypton ; measurement error ; methane ; neon ; nitrogen ; steady-state method ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Air desorbed from the measuring instrument can falsify the thermal conductivity of a gas measured by steady-state methods. For a guarded hot-plate apparatus the contamination effect was determined to depend on both the residence time in the system and the temperature. The investigation covered the gases H2, He, Ne, CH4, N2, air, Ar, and Kr. For gases whose conductivity is better than that of air (H2, He) the measured values are too small, and for gases of poorer conductivity they are too high. Corrections for the effect of impurity have been applied to the measurements presented. These impurity corrections are considerably larger than the precision of the measurements, but they are of the order of the estimated overall uncertainty of the measurements. The departures between the corrected thermal conductivities reported here and values taken from the correlations in the literature run up to 5 % at the highest temperatures.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 88
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 615-624 
    ISSN: 1572-9567
    Keywords: photothermal deflection ; thermal conductivity ; thin film
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract A three-dimensional theoretical model has been developed to calculate the normal probe beam deflection of the obliquely crossed photothermal deflection configuration in samples which consist of thin films deposited on substrates. Utilizing the dependence of the normal component of probe beam deflection on the cross-point position of the excitation and probe beams, the thermal conductivity of the thin film can be extracted from the ratio of the two maxima of the normal deflection amplitude, which occurs when the cross-point is located near both surfaces of the sample. The effects of other parameters, including the intersect angle between the excitation and the probe beams in the sample, the modulation frequency of the excitation beam, the optical absorption and thickness of the thin films, and the thermal properties of substrates on the thermal conductivity measurement of the thin film, are discussed. The obliquely crossed photothermal deflection technique seems to be well suited for thermal conductivity measurements of thin films with a high thermal conductivity but a low optical absorption, such as diamond and diamond-like carbon, deposited on substrates with a relatively low thermal conductivity.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 89
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 193-204 
    ISSN: 1572-9567
    Keywords: argon ; Hartree-Fock dispersion (HFD) potential ; interatomic potential ; shock-tube conductivity ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract An accurate interatomic potential was constructed by fitting a realistic function, constrained by theory, to a set of judiciously selected macroscopic and microscopic properties but not including thermal conductivity. Using this potential, accurate values of thermal conductivity of argon are obtained for the temperature range 100 to 6600 K. These are presented in tabular form as well as in terms of a correlation function.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 90
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 153-157 
    ISSN: 1572-9567
    Keywords: core sizes ; Enskog ; hard-sphere theory ; methane ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Thermal conductivities have been calculated for dense fluid methane from the exact smooth hard-sphere expression valid for monoatomics with core sizes derived from fitting self-diffusion and viscosity data. The results are lower than experimental values by about 16% at all densities greater than the critical density. This difference is attributed to the effect of internal energy transport on this property.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 91
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 293-316 
    ISSN: 1572-9567
    Keywords: argon ; thermal conductivity ; thermal diffusivity ; toluene ; transient hot-wire technique ; m-xylene
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The theory of the transient hot-wire technique for thermal conductivity measurements is reassessed in the special context of thermal diffusivity measurements. A careful examination of the working equation and an error analysis are employed to identify the principal sources of error. Notwithstanding earlier claims to the contrary, the best precision that can be attained in thermal diffusivity measurements is of the order of ±3%, while the accuracy is inevitably poorer. Experimental evidence is adduced from two different instruments that supports the analysis given here. Although the technique cannot yield values of the thermal diffusivity, k, as accurate as can be achieved by the use of the best possible individual values of λ,ρ, and C p in the relation k=λ/ρC p, the simplicity of the technique makes it attractive for many purposes. It is even possible to derive values of the isobaric heat capacity C p for many fluids not available from other methods.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 92
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 8 (1987), S. 663-670 
    ISSN: 1572-9567
    Keywords: n-hexane ; n-heptane ; n-decane ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New absolute measurements of the thermal conductivity of liquid n-hexane, n-heptane, and n-decane are reported. The measurements have been carried out in the temperature range 300–370 K at atmospheric pressure in a transient hotwire instrument. The accuracy of the measurements is estimated to be ±0.5%. The density dependence of the thermal conductivity of n-hexane and n-heptane is found to be well described by a universal equation for the hydrocarbons based on a rough hard-sphere model. The measurements of the three hydrocarbons studied are also employed to generate more accurate effective core volumes, which are the only parameters characteristic of the fluid required for the application of the proposed universal scheme.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 93
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 465-479 
    ISSN: 1572-9567
    Keywords: fluorocarbon ; halogenated ethane ; liquid ; high pressure ; refrigerant ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract New experimental data on the thermal conductivity of liquid halogenated ethanes, R112 (CCl2F-CCl2F), R113 (CCl2F-CClF2), R114 (CClF2-CClF2), R114B2 (CBrF2-CBrF2), and R123 (CHCl2-CF3), are presented in the temperature range from 283 to 348 K at pressures up to 200 MPa or the freezing pressures. The measurements were carried out by a transient hot-wire apparatus within an uncertainty of ±1.0%. The thermal conductivity data obtained have been analyzed by means of the corresponding-states principle and other empirical methods. It is found that the corresponding-states correlation λ=f(Tr, Pr) holds well for R112, R113, and R114. The thermal conductivity can also be correlated satisfactorily with temperature, pressure, and molar volume by a similar expression to the Tait equation and the dense hard-sphere model presented by Dymond.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 94
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 611-625 
    ISSN: 1572-9567
    Keywords: heat transfer ; insulation ; microspheres ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Experimental results of investigations of the heat exchange by residual gas in microsphere insulations are presented. The results of measurements of microsphere effective thermal conductivity versus residual gas (N2) pressure in the pressure range of 10−3−105 Pa are also given. A sample of self-pumping microsphere insulation was prepared and its thermal parameters were tested. In comparison to the standard microsphere insulation, the self-pumping insulation yielded lower thermal conductivity results over the entire pressure range. The stability of its thermal parameters as a result of considerable gas input into the insulation volume is discussed. Measurements of temperature and pressure distributions inside the microsphere layer were performed. Plots of temperature and pressure gradients inside the layer of the microsphere insulation are presented.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 95
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 969-981 
    ISSN: 1572-9567
    Keywords: electrical resistivity ; enthalpy ; high temperature ; liquid alloys ; rhenium alloy ; specific heat ; thermal conductivity ; thermal diffusivity ; tungsten alloy
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract In earlier experiments we have studied pure elements with a fast pulse heating technique to obtain thermophysical properties of the liquid state. We report here results for thermophysical properties such as specific heat and dependences among enthalpy, electrical resistivity, and temperature, for four W–Re alloys (3.95, 21.03, 23.84, and 30.82 at % of Re) in a wide temperature range covering solid and liquid states. Thermal conductivity is calculated using the Wiedemann–Franz law for the liquid alloy, as.well as data for thermal diffusivity for the beginning of the liquid phase. Additionally, data for the entire temperature range studied have been analyzed in comparison with those of the constituent elements, tungsten and rhenium, since both metals have been studied previously with the same experimental technique. Such information is of interest in the field of metallurgy since W–Re alloys of low Re content in the region of mutual component solubility in the solid state are widely used as thermocouple materials for the purposes of high-temperature thermometry.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 96
    ISSN: 1572-9567
    Keywords: critical state ; electron concentration ; lead ; shock compression ; spectroscopy ; thermal conductivity
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Experiments were performed to investigate the behavior of lead near its critical point. Emission spectra of shocked lead samples during unloading into helium at different initial pressures were measured by an optical multichannel analyzer (OMA), as well as by a fast optical pyrometer. To describe the obtained experimental data, a model of a thin mixture layer was suggested, in which helium emits due to the presence of external electrons from lead.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 97
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 9 (1988), S. 873-883 
    ISSN: 1572-9567
    Keywords: high temperature ; phase transition ; stainless steel ; thermal conductivity ; thermal expansion
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Renewed interest in the use of metallic fuel in a liquid-metal fast breeder reactor has prompted study of the thermodynamic and transport properties of fuel and cladding materials. Two stainless steels are of particular interest because of their good performance under irradiation. These are D9, an austenitic steel, and HT9, a ferritic steel. Thermal conductivity and thermal expansion data for these cladding alloys are of particular interest in assessing in-reactor behavior. These two properties were measured for the two steels at temperatures to 1200 K. Of particular interest is the influence on these properties of a phase transition in HT9.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 98
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 1229-1238 
    ISSN: 1572-9567
    Keywords: food properties ; Peltier effect ; thermal conductivity ; thermoelectric heat pump ; tropical foods
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The objective of this work was to test a novel experimental technique to determine the thermal conductivity of low-thermal conductivity materials and tropical foods. The experimental method was based on the Peltier effect and its application to the thermoelectric heat pump. This device became practical recently with the development of semiconductor thermocouple materials. The module assembly used in this work had 127 thermocouples connected in series electrically and in parallel thermally. The heat transfer area of the module was 3.96×3.96 cm2. The equipment was calibrated using standard materials of known thermal conductivity: Plexiglas and Bakelite. Then the κ values were easily computed from a steady-state energy balance equation.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 99
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 19 (1998), S. 1239-1251 
    ISSN: 1572-9567
    Keywords: criterion of homogeneity ; dispersed composites ; finite element method (FEM) ; laser flash method ; thermal conductivity ; thermal diffusivity ; steady-state comparison method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract The effective thermal conductivity of dispersed composites with a hot-melt-adhesive matrix, measured using the steady-state method, is compared with the apparent thermal conductivity calculated from the average heat capacity and from the thermal diffusivity measured by the laser-flash method. The transient effect has been observed obviously at higher volume percentages for various dispersed particle sizes and ratios of the thermal conductivity values of dispersed and continuous phases. All of the experimental results are compared with those calculated by existing models and by the finite element method (FEM). An attempt has been made to show how the criterion for the homogeneity of dispersed composites under transient conditions is affected by the percentages of dispersed phase, dispersed particle size, and ratio of the thermal conductivity values of dispersed and continuous phases.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 100
    Electronic Resource
    Electronic Resource
    Springer
    International journal of thermophysics 20 (1999), S. 55-62 
    ISSN: 1572-9567
    Keywords: mixture ; R125 ; R134a ; R125+R134a ; refrigerant ; thermal conductivity ; transient hot-wire method
    Source: Springer Online Journal Archives 1860-2000
    Topics: Physics
    Notes: Abstract Thermal conductivities of zeotropic mixtures of R125 (CF3CHF2) and R134a (CF3CH2F) in the liquid phase are reported. Thermal conductivities have been measured by a transient hot-wire method with one bare platinum wire. Measurements have been carried out in the temperature range of 233 to 323 K and in the pressure range of 2 to 20 MPa. The dependence of thermal conductivity on temperature, pressure, and composition of the binary mixture is presented. Measured thermal conductivity data are correlated as a function of temperature, pressure, and overall composition of the mixture. The uncertainty of our measurements was estimated to be better than 2%.
    Type of Medium: Electronic Resource
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...