ALBERT

Description: High-resolution 3D (HR3D) seismic data are important for hydrocarbon exploration of shallow reservoirs, site characterization, and geohazard assessments. The goal of this contribution is to identify and quantify the parameters to increase the resolution of HR3D seismic data to meter scale. The main acquisition parameters controlling the resolution of the collected data are the spectrum of the seismic source, source-receiver offset range, and trace density. An evolution to one-meter-scale resolution of 3D seismic will rely on combining a reproducible seismic source with high frequencies up to at least 600 Hz, a high uniform trace density of more than 4 million traces per square kilometer, and an offset range shorter than approximately 200 m. The resulting 3D seismic data volume will reach meter-scale resolution for water and target depths of less than 600 m. The proposed HR3D system will be suitable for 3D and 4D characterization of seabed properties and shallow stratigraphy, the identification of geohazards and hydrocarbon leakage, and monitoring the environmental impact of offshore activities. The P-Cable 3D system is an excellent starting point for achieving one-meter-scale resolution due to its flexible and tight meter-scale shot and receiver spacing.

Description: Global industry is showing a great interest in the field of sustainability owing to the increased attention for ecological safety and utilization of renewable materials. For the scientific community, the challenge lies in the identification of greener synthetic approaches for reducing the environmental impact. In this context, we propose the preparation of novel biocomposites consisting of natural rubber latex (NRL) and sepiolite (Sep) fibers through the latex compounding technique (LCT), an ecofriendly approach where the filler is directly mixed with a stable elastomer colloid. This strategy favors a homogeneous dispersion of hydrophilic Sep fibers in the rubber matrix, allowing the production of high-loaded sepiolite/natural rubber (Sep/NR) without the use of surfactants. The main physicochemical parameters which control Sep aggregation processes in the aqueous medium were comprehensively investigated and a flocculation mechanism was proposed. The uniform Sep distribution in the rubber matrix, characteristic of the proposed LCT, and the percolative filler network improved the mechanical performances of Sep/NR biocomposites in comparison to those of analogous materials prepared by conventional melt-mixing. These outcomes indicate the suitability of the adopted sustainable procedure for the production of high-loaded clay–rubber nanocomposites with remarkable mechanical features.

Description: A prenatal diet affects materno-foetal outcomes. This is a post hoc analysis of the St. Carlos gestational diabetes mellitus (GDM) Prevention Study. It aims to evaluate the effect of a late first-trimester (〉12 gestational weeks) degree of adherence to a MedDiet pattern—based on six food targets—on a composite of materno-foetal outcomes (CMFCs). The CMFCs were defined as having emergency C-section, perineal trauma, pregnancy-induced hypertension and preeclampsia, prematurity, large-for-gestational-age, and/or small-for-gestational-age. A total of 874 women were stratified into three groups according to late first-trimester compliance with six food targets: 〉12 servings/week of vegetables, 〉12 servings/week of fruits, 3 servings/week of nuts, 〉6 days/week consumption of extra virgin olive oil (EVOO), and ≥40 mL/day of EVOO. High adherence was defined as complying with 5–6 targets; moderate adherence 2–4 targets; low adherence 0–1 targets. There was a linear association between high, moderate, and low adherence, and a lower risk of GDM, CMFCs, urinary tract infections (UTI), prematurity, and small-for-gestational-age (SGA) newborns (all p 〈 0.05). The odds ratios (95% CI) for GDM and CMFCs in women with a high adherence were 0.35((0.18–0.67), p = 0.002) and 0.23((0.11–0.48), p 〈 0.001), respectively. Late first-trimester high adherence to the predefined six food targets is associated with a reduction in the risk of GDM, CMFCs, UTI, prematurity, and SGA new-borns.

Description: In this study, the chemical profiles and antioxidant activities of red cabbage anthocyanin (RCA)-enriched extract are evaluated. The effects of column temperature on the HPLC resolution of the RCAs are studied. The HPLC resolutions became better as the column temperature increased from 20 °C–45 °C. An optimized HPLC condition was achieved at 45 °C and used for the quantification and qualification of the RCAs. The anthocyanins in the enriched powder are all derivatives of cyanidin (268 ± 2 μg/mg), mainly with 19% nonacylated, 51% monoacylated, and 31% diacylated structures with ferulic, sinapic, p-coumaric, and caffeic acids characterized by HPLC-MS. The RCA extracts markedly reduced intracellular oxidative stress production by H2O2 on HepG2 cells and consequently ameliorated cell apoptosis and improved viability. The analytical method and cellular antioxidant activity demonstration of the RCAs will greatly facilitate their functional applications.

Description: Chitosan and chitosan-nanoparticles were combined to prepare biobased and unplasticized film blends displaying antimicrobial activity. Nanosized chitosans obtained by sonication for 5, 15, or 30 min were combined with chitosan at 3:7, 1:1, and 7:3 ratios, in order to adjust blend film mechanical properties and permeability. The incorporation of nanosized chitosans led to improvements in the interfacial interaction with chitosan microfibers, positively affecting film mechanical strength and stiffness, evidenced by scanning electron microscopy. Nanosized or blend chitosan film sensitivity to moisture was significantly decreased with the drop in biocomposite molecular masses, evidenced by increased water solubility and decreased water vapor permeability. Nanosized and chitosan interactions gave rise to light biobased films presenting discrete opacity and color changes, since red-green and yellow-blue colorations were affected. All chitosan blend films exhibited antimicrobial activity against both Gram-positive and Gram-negative bacteria. The performance of green unplasticized chitosan blend films displaying diverse morphologies has, thus, been proven as a potential step towards the design of nontoxic food packaging biobased films, protecting against spoilage microorganisms, while also minimizing environmental impacts.

Description: Growing public concerns about health haves prompted the search for novel food sources. The study is focused on the seeds, sprouted seeds and microgreens of Trifolium pratense, T. medium, Medicago sativa, M. lupulina, Onobrychis viciifolia, Astragalus glycyphyllos and A. cicer species as a potential source of value-added food ingredientsr. The samples were analysed for nutritional (wet chemistry, standard methods) and mineral (atomic absorption spectroscopy, UV-Vis spectrophotometry) profiles, isoflavones (ultra-performance liquid with diode array detector –UPLC-DAD), coumestrol (UPLC-DAD), condensed tannins (CT) (vanillin-H2SO4 assay) and triterpene saponins (UPLC with triple-stage quadrupole MS). In our study, each species displayed high, but species-dependent nutritional, mineral and phytochemical value. All counterparts of legumes were mineral and protein rich. A. glycyphyllos samples, especially seeds, were abundant in iron. Trifolium spp. were found to be important sources of isoflavones, Medicago spp. of coumestrol and saponins, and O. viciifolia of CT. The protein and phytochemical contents increased and total carbohydrates decreased from seeds to microgreens.Our findings proved for the first time that seeds, sprouted seeds, and especially microgreens of small-seeded legumes are promising new sources of ingredients for fortification of staple foods with bioactive compounds, minerals and nutrients.

Description: The initial channels of thermal decomposition mechanism of 2,6-diamino-3,5-dinitropyrazine-1-oxide (LLM-105) molecule were investigated. The results of quantum chemical calculations revealed four candidates involved in the reaction pathway, including the C–NO2 bond homolysis, nitro–nitrite rearrangement followed by NO elimination, and H transfer from amino to acyl O and to nitro O with the subsequent OH or HONO elimination, respectively. In view of the further kinetic analysis and ab initio molecular dynamics simulations, the C–NO2 bond homolysis was suggested to be the dominant step that triggered the decomposition of LLM-105 at temperatures above 580 K. Below this temperature, two types of H transfer were considered as the primary reactions, which have advantages including lower barrier and high rate compared to the C–NO2 bond dissociation. It could be affirmed that these two types of H transfer are reversible processes, which could buffer against external thermal stimulation. Therefore, the excellent thermal stability of LLM-105, that is nearly identical to that of 1,3,5-triamino-2,4,6-trinitrobenzene, can be attributed to the reversibility of H transfers at relatively low temperatures. However, subsequent OH or HONO elimination reactions occur with difficulty because of their slow rates and extra energy barriers. Although nitro–nitrite rearrangement is theoretically feasible, its rate constant is too small to be observed. This study facilitates the understanding of the essence of thermal stability and detailed decomposition mechanism of LLM-105.

Description: The effects of thioridazine (TDZ) and chlorpromazine (CPZ) and bovine serum albumin nanoparticles (BSA-NPs) on erythrocyte membranes have been investigated. Two kinds of hemolytic assays were used; hemolysis under hypotonic conditions and hemolysis in physiological conditions. Under hypotonic conditions for 50% hemolysis, both TDZ and CPZ have a biphasic effect on membranes; namely, stabilization at low concentrations and destabilization after reaching a critical concentration. In physiological conditions, there are other critical concentrations above which both drugs hemolyse the erythrocites. In each case, the critical concentrations of TDZ are lower than those of CPZ, which is consistent with the ratio of their partition coefficients. When BSA-NPs are added to the erythrocyte suspension simultaneously with the drugs, the critical concentrations increase for both drugs. The effect is due to the incorporation of a portion of drug substances into the BSA-nanoparticles, which consequently leads to the decrease of the active drug concentrations in the erythrocyte suspension medium. Similar values of the critical concentrations are found when the BSA-NPs are loaded with the drugs before their addition to the erythrocyte suspension in which case the events of the partition are: desorption of the drug from BSA-NPs, diffusion through the medium, and adsorption on erythrocyte membranes. This result suggests that the drugs are not influenced by the processes of adsorption and desorption onto and out of the BSA-NPs, and that the use of BSA-NPs as drug transporters would allow intravenous administration of higher doses of the drug without the risk of erythrocyte hemolysis.

Description: Transparent films of cellulose nanocrystals (CNC) are prepared by dip-coating on glass substrates from aqueous suspensions of hydrolyzed filter paper. Dragging forces acting during films’ deposition promote a preferential alignment of the rod-shaped CNC. Films that are 2.8 and 6.0 µm in thickness show retardance effects, as evidenced by placing them between a linearly polarized light source and a linear polarizer sheet in the extinction configuration. Transmission Mueller matrix spectroscopic ellipsometry measurements at normal incidence as a function of sample rotation were used to characterize polarization properties. A differential decomposition of the Mueller matrix reveals linear birefringence as the unique polarization parameter. These results show a promising way for obtaining CNC birefringent films by a simple and controllable method.

Description: Mental stress, such as anxiety and conflict, causes physiological changes, such as changes in autonomic nervous activity and gastric ulcers. In addition, stress induces glucocorticoids and changes the hippocampal brain-derived neurotrophic factor (BDNF) expression levels. We previously reported that Acanthopanax senticosus HARM (ASH) prevents stress-induced gastric ulcers. Thus, we investigated the potential anxiolytic effect and influence of ASH on the hippocampus BDNF-related protein in male Sprague-Dawley rats fed 1% and 5% ASH extract-containing food for one week using novelty suppressed feeding (NSF) and improved elevated beam walking (IEBW) tests. ASH treatment significantly decreased latency to eat in the NSF test and increased the time spent on the open arm in the IEBW test. ASH5% treatment showed a significant decrease in LFnu, indicative of sympathetic nervous activity, and a significant increase in HFnu, indicative of parasympathetic nervous activity, in the NSF test. In addition, ASH1% and ASH5% treatments significantly decreased LFnu and significantly increased HFnu in the IEBW test. ASH5% treatment significantly increased hippocampal BDNF protein expression in both Western blotting and immunohistochemistry experiments. Our findings suggest that anxiolytic effects of ASH occur via the regulation of autonomic function and increased hippocampal BDNF signaling.

Description: A hitherto unknown polyoxygenated flavonol robinobioside (gossypetin-3-O-β-d-robinobioside) was isolated from the leaves of Caesalpinia gilliesii along with thirteen known phenolic secondary metabolites. The isolated compounds were characterized using spectroscopic analysis, including 1D and 2D NMR and mass spectrometry (MS) analyses. The extract reduced the level of liver damage in CCl4-induced liver injury in rats. A decrease of the liver biomarkers—aspartate aminotransferase (AST) and alanine aminotransferase (ALT) and an increase of total antioxidant capacity (TAC) levels—were observed similar to the liver protecting drug silymarin. In addition, the extract showed promising activity against carrageenan-induced paw edema in rats and protected their stomachs against ethanol-induced gastric ulcers in a concentration dependent fashion. The observed activities could be attributed to the high content of antioxidant polyphenols. Our results suggest that the C. gilliesii has the capacity to scavenge free radicals and can protect against oxidative stress, and liver and stomach injury.

Description: Baicalein (BAI), one of the main components of Scutellaria baicalensis Georgi, possesses numerous pharmacological properties, including anti-cancer, anti-oxidative, anti-virus and anti-bacterial activities. The purpose of this study was to evaluate the hepatoprotective effect of baicalein against acetaminophen (APAP)-exposed liver injury in mice, and elucidate the underlying hepatoprotective mechanism. Baicalein pretreatment significantly alleviated the elevation of IL-6, IL-1β and TNF-α in serum and hepatic in a dose-dependent manner. It also dose-dependently reduced the hepatic malondialdehyde (MDA) concentration, as well as the depletion of hepatic superoxide dismutase (SOD), hepatic glutathione (GSH) and hepatic catalase (CAT). Moreover, pretreatment with baicalein significantly ameliorated APAP-exposed liver damage and histological hepatocyte changes. Baicalein also relieved APAP-induced autophagy by regulating AKT/mTOR pathway, LC3B and P62 expression. Furthermore, the hepatoprotective effect of baicalein to APAP-induced liver injury involved in Jak2/Stat3 and MAPK signaling pathway. Taken together, our findings suggested that baicalein exhibits the ability to prevent liver from APAP-induced liver injury and provided an underlying molecular basis for potential applications of baicalein to cure liver injuries.

Description: Volatile sulfur compounds gradually develop in Lentinula edodes after hot-air drying, and many genes are involved in the generation of these sulfur compounds. The expression stability of reference genes may vary in a particular experimental treatment when analyzing their expressions by quantitative real-time polymerase chain reaction (qRT-PCR). In this study, the expression profile of 17 candidate genes was assessed in L. edodes under treatment at 50 °C for 0, 1, 2, and 3 h, and the expression stability of each reference gene was analyzed by three statistical algorithms, including geNorm, NormFinder, and BestKeeper. Results indicated that the two optimal reference genes for mycelium and fruiting body were CAC and DAHP as well as CAC and NUP, respectively. Additionally, CAC and DAHP were found to be the two most stable reference genes across the mycelium and fruiting body set. Our results will provide a genetic foundation for further research on the metabolism genes of sulfur compounds in L. edodes.

Description: Carbonized pollen grains of Typha (CPT) were widely used in clinical for antithrombosis, wound and bleeding in China. In order to ensure the role of drugs, it is very important to control the quality of drugs. However, there is a lack of monitoring methods in the process of charcoal preparation. To characterize the process of CPT, we used thermal analysis, scanning electron microscope (SEM), color measurement, Fourier transform infrared spectrometry (FTIR) and HPLC. In this study, 7 min was the optimal processing time and the heating process condition should be controlled under 272.35 ± 7.23 °C. This comprehensive strategy to depict the whole carbonizing process would provide new ideas for researches on quality control of Traditional Chinese Medicine (TCM) and processing theory of charcoal medicine.

Description: This paper is a review that surveys work on the fabrication of miniature alkali vapor cells for miniature and chip-scale atomic clocks. Technology on microelectromechanical systems (MEMS) cells from the literature is described in detail. Special attention is paid to alkali atom introduction methods and sealing of the MEMS structure. Characteristics of each technology are collated and compared. The article’s rhetoric is guided by the proposed classification of MEMS cell fabrication methods and contains a historical outline of MEMS cell technology development.

Description: The two-probe device of nanorod-coupled gold electrodes is constructed based on the triangular zinc oxide (ZnO) nanorod. The length-dependent electronic transport properties of the ZnO nanorod was studied by density functional theory (DFT) with the non-equilibrium Green’s function (NEGF). Our results show that the current of devices decreases with increasing length of the ZnO nanorod at the same bias voltage. Metal-like behavior for the short nanorod was observed under small bias voltage due to the interface state between gold and the ZnO nanorod. However, the influence of the interface on the device was negligible under the condition that the length of the ZnO nanorod increases. Moreover, the rectification behavior was observed for the longer ZnO nanorod, which was analyzed from the transmission spectra and molecular-projected self-consistent Hamiltonian (MPSH) states. Our results indicate that the ZnO nanorod would have potential applications in electronic-integrated devices.

Description: This paper employs the solution-doping technique for the fabrication of active polymer optical fibers (POFs), in which the dopant molecules are directly incorporated into the core of non-doped uncladded fibers. Firstly, we characterize the insertion of a solution of rhodamine B and methanol into the core of the fiber samples at different temperatures, and we show that better optical characteristics, especially in the attenuation coefficient, are achieved at lower temperatures. Moreover, we also analyze the dependence of the emission features of doped fibers on both the propagation distance and the excitation time. Some of these features and the corresponding ones reported in the literature for typical active POFs doped with the same dopant are quantitatively similar among them. This applies to the spectral location of the absorption and the emission bands, the spectral displacement with propagation distance, and the linear attenuation coefficient. The samples prepared in the way described in this work present higher photostability than typical samples reported in the literature, which are prepared in different ways.

Description: CaCO3 nanoparticles of around 60 nm were obtained by a co-precipitation method and used as filler to prepare low-density polyethylene (LDPE) composites by melt blending. The nanoparticles were also organically modified with oleic acid (O-CaCO3) in order to improve their interaction with the LDPE matrix. By adding 3 and 5 wt% of nanofillers, the mechanical properties under tensile conditions of the polymer matrix improved around 29%. The pure LDPE sample and the nanocomposites with 5 wt% CaCO3 were photoaged by ultraviolet (UV) irradiation during 35 days and the carbonyl index (CI), degree of crystallinity (χc), and Young’s modulus were measured at different times. After photoaging, the LDPE/CaCO3 nanocomposites increased the percent crystallinity (χc), the CI, and Young’s modulus as compared to the pure polymer. Moreover, the viscosity of the photoaged nanocomposite was lower than that of photoaged pure LDPE, while scanning electron microscopy (SEM) analysis showed that after photoaging the nanocomposites presented cavities around the nanoparticles. These difference showed that the presence of CaCO3 nanoparticles accelerate the photo-degradation of the polymer matrix. Our results show that the addition of CaCO3 nanoparticles into an LDPE polymer matrix allows future developments of more sustainable polyethylene materials that could be applied as films in agriculture. These LDPE-CaCO3 nanocomposites open the opportunity to improve the low degradation of the LDPE without sacrificing the polymer’s behavior, allowing future development of novel eco-friendly polymers.

Description: Samento (extract from Uncaria tomentosa) and Banderol (extract from Otoba parvifolia) have been demonstrated to have anti-inflammatory and antimicrobial properties, e.g., against different morphological forms of Borrelia burgdorferi. However, there is hardly any data on the pharmacological safety of these two herbal medicines. This in vitro study aimed at scrutinizing their possible characteristics as perpetrators in pharmacokinetic herbal–drug interactions. Inhibition of cytochrome P450 enzymes (CYPs) was quantified by commercial kits and inhibition of drug transporters by use of fluorescent probe substrates. Induction was quantified by real-time RT-PCR and activation of pregnane x receptor (PXR) and aryl hydrocarbon receptor (AhR) by reporter gene assays. Organic anion transporting polypeptide 1B1 (OATP1B1) (IC50 = 0.49 ± 0.28%) and OATP1B3 (IC50 = 0.65 ± 0.29%) were potently inhibited by Banderol, but only weakly by Samento. CYP3A4 was inhibited about 40% at a Samento concentration of 1%. Samento significantly induced mRNA expression of CYP2J2, UGT1A3, UGT1A9, ABCB1, and SLCO1B1 and strongly activated PXR, but hardly AhR. In conclusion, the perpetrator profiles of Samento and Banderol for herb–drug interactions completely differ. Clinical studies are strongly recommended to clarify whether the effects observed in vitro are of clinical relevance.

Description: The characteristics of the pore structure and gas migration in soft coalbeds are the premise of evaluating gas discharge in soft coalbeds. To explore the pore structure characteristics of soft coal masses, the No. 5 soft coalbed in the eastern zone of Chenghe Mining Area, was investigated and compared with the No. 5 hard coalbed in the western zone. By using a mercury intrusion method, low-temperature liquid nitrogen adsorption, and scanning electron microscopy (SEM), the pore structure characteristics of the No. 5 coalbed were explored. Moreover, based on fractal theory, the pore structure of coal was characterized. The results showed the pores in soft coal mainly appeared as small pores and micropores in which the small pores accounted for nearly half of the total pore volume. Mesopores and macropores were also distributed throughout the soft coal. The mercury-injection and mercury-ejection curves of soft coal showed significant hysteresis loops, implying that pores in coal samples were mainly open while the mercury-injection curve of hard coal was consistent with its mercury-ejection curve, showing no hysteresis loop while having an even segment, which indicated that closed pores occupied the majority of the pore volume in the coal samples. The curves of low-temperature nitrogen adsorption of soft coal all follow an IV-class isotherm. Moreover, the fractal dimensions of soft coal are respectively larger than the fractal dimensions of hard coal. It can be seen that the characterization of pores and fractures of the soft coal was different from the hard coal in the western distinct of the old mining area. The gas prevention and control measures of soft coal should be formulated according to local conditions.

Description: In this work, the ethylene-propylene-diene monomer/polypropylene (EPDM/PP) thermoplastic elastomer filled with intumescent flame retardants (IFR) is fabricated by melting blend. The IFR are constituted with melamine phosphate-pentaerythritol (MP/PER) by compounding and reactive extruding, respectively. The effects of two kinds of MP/PER with different contents on the thermal stability, flame retardancy, and mechanical properties of materials are investigated by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), limiting oxygen index (LOI), UL-94, cone calorimeter test (CCT), and scanning electron microscopy (SEM). FTIR results show that the reactive extruded MP/PER partly generates melamine pyrophosphate (MPP) compared with compound masterbatches. TGA data indicate that the best thermal stability is achieved when the molar ratio of MP/PER reaches 1.8. All the reactive samples show a higher flame retardancy than compound ones. The CCT results also exhibit the same trend as above in heat release and smoke production rate. The EPDM/PP composites filled with 30 and 35% reactive MP/PER exhibit the improved flame retardancy but become stiffer and more brittle. SEM photos display that better dispersion and smaller particle size are obtained for reactive samples.

Description: Continuous carbon fiber (CF)-reinforced poly (ether ether ketone) (PEEK) composites have excellent mechanical properties, but their processing techniques are limited. Therefore, we promoted a braiding method based on the hybrid fiber method by hot-compacting CF/PEEK plain weave fabrics to solve the problem of difficult wetting between CF and PEEK. Four parameters—melting temperature, molding pressure, crystallization temperature and the resin contents—were investigated for optimized fabrication. After studying the melting range, thermal stability and the contact angle of PEEK under different temperatures, the melting temperature was set at 370 °C. An ultra-depth-of-field 3D microscope was adopted to investigate the effects of molding pressure in the melting stage. The tensile strength or modulus along and perpendicular to the carbon fiber direction and crystallinity under different crystallization temperatures were analyzed. As a result, the sample crystalized at 300 °C showed an excellent tensile properties and crystallinity. The increased mass ratio of PEEK ranging from 50.45% to 59.07% allowed for much stronger interfacial strength; however, the higher resin content can lead to the dispersion of CFs, loss of resin and the formation of defects during processing. Finally, the optimal resin mass content was 59.07%, with a tensile strength of 738.36 ± 14.49 MPa and a flexural strength of 659.68 ± 57.53 MPa. This paper studied the optimized processing parameters to obtain better properties from CF/PEEK plain weave fabrics and to further broaden the specific applications of CF/PEEK composites, demonstrating a new direction for its fabrication.

Description: Polyelectrolytes are an important class of polymeric materials and are increasingly used in complex industrial formulations. A core use of these materials is in mixtures with surfactants, where a combination of hydrophobic and electrostatic interactions drives unique solution behavior and structure formation. In this review, we apply a molecular level perspective to the broad literature on polyelectrolyte-surfactant complexes, discussing explicitly the hydrophobic and electrostatic interaction contributions to polyelectrolyte surfactant complexes (PESCs), as well as the interplay between the two molecular interaction types. These interactions are sensitive to a variety of solution conditions, such as pH, ionic strength, mixing procedure, charge density, etc. and these parameters can readily be used to control the concentration at which structures form as well as the type of structure in the bulk solution.

Description: How the body plan is established and maintained in multicellular organisms is a central question in developmental biology. Thanks to its simple and symmetric structure, the root represents a powerful tool to study the molecular mechanisms underlying the establishment and maintenance of developmental axes. Plant roots show two main axes along which cells pass through different developmental stages and acquire different fates: the root proximodistal axis spans longitudinally from the hypocotyl junction (proximal) to the root tip (distal), whereas the radial axis spans transversely from the vasculature tissue (centre) to the epidermis (outer). Both axes are generated by stereotypical divisions occurring during embryogenesis and are maintained post-embryonically. Here, we review the latest scientific advances on how the correct formation of root proximodistal and radial axes is achieved.

Description: Multifunctional liposomes containing manganese ferrite/gold core/shell nanoparticles were developed. These magnetic/plasmonic nanoparticles were covered by a lipid bilayer or entrapped in liposomes, which form solid or aqueous magnetoliposomes as nanocarriers for simultaneous chemotherapy and phototherapy. The core/shell nanoparticles were characterized by UV/Visible absorption, X-Ray Diffraction (XRD), Transmission Electron Microscopy (TEM), and Superconducting Quantum Interference Device (SQUID). The magnetoliposomes were characterized by Dynamic Light Scattering (DLS) and TEM. Fluorescence-based techniques (FRET, steady-state emission, and anisotropy) investigated the incorporation of a potential anti-tumor drug (a thienopyridine derivative) in these nanosystems. The core/shell nanoparticles exhibit sizes of 25 ± 2 nm (from TEM), a plasmonic absorption band (λmax = 550 nm), and keep magnetic character. XRD measurements allowed for the estimation of 13.3 nm diameter for manganese ferrite core and 11.7 nm due to the gold shell. Aqueous magnetoliposomes, with hydrodynamic diameters of 152 ± 18 nm, interact with model membranes by fusion and are able to transport the anti-tumor compound in the lipid membrane, with a high encapsulation efficiency (EE (%) = 98.4 ± 0.8). Solid magnetoliposomes exhibit hydrodynamic diameters around 140 nm and also carry successfully the anticancer drug (with EE (%) = 91.2 ± 5.2), while also being promising as agents for phototherapy. The developed multifunctional liposomes can be promising as therapeutic agents for combined chemo/phototherapy.

Description: A magnetic chicane bunch compressor for a new compact accelerator-based terahertz (THz) radiation source at the Institute of Advanced Energy, Kyoto University, was completely installed in March 2016. The chicane is employed to compress an electron bunch with an energy of 4.6 MeV generated by a 1.6-cell photocathode radio frequency (RF)-gun. The compressed bunch is injected into a short planar undulator for THz generation by coherent undulator radiation (CUR). The characteristics of the bunch compressor and the compressed bunch were investigated by observing the coherent transition radiation (CTR). The CTR spectra, which were analyzed by using a Michelson interferometer, and the compressed bunch length were also estimated. The results were that the chicane could compress the electron bunch at a laser injection phase less than 45 degrees, and the maximum CTR intensity was observed at a laser injection phase around 24 degrees. The optimum value of the first momentum compaction factor was around −45 mm, which provided an estimated rms bunch length less than 1 ps.

Description: Cardiac dysfunction secondary to cancer may exert a negative impact in patients’ tolerance to therapeutics, quality of life, and survival. The aim of this study was to evaluate the potential therapeutic effect of exercise training on the heart in the setting of cancer, after diagnosis. Thus, the molecular pathways harbored in heart mitochondria from a murine model of chemically-induced urothelial carcinoma submitted to 8-weeks of high intensity treadmill exercise were characterized using mass spectrometry-based proteomics. Data highlight the protective effects of high intensity exercise training in preventing left ventricle diastolic dysfunction, fibrosis, and structural derangement observed in tumor-bearing mice. At the mitochondrial level, exercise training counteracted the lower ability to produce ATP observed in the heart of animals with urothelial carcinoma and induced the up-regulation of fatty acid oxidation and down-regulation of the biological process “cardiac morphogenesis”. Taken together, our data support the prescription of exercise training after cancer diagnosis for the management of disease-related cardiac dysfunction.

Description: The growing prevalence of metabolic syndrome (MetS) in the U.S. and even worldwide is becoming a serious health problem and economic burden. MetS has become a crucial risk factor for the development of type 2 diabetes mellitus (T2D) and cardiovascular diseases (CVD). The rising rates of CVD and diabetes, which are the two leading causes of death, simultaneously exist. To prevent the progression of MetS to diabetes and CVD, we have to understand how MetS occurs and how it progresses. Too many causative factors interact with each other, making the investigation and treatment of metabolic syndrome a very complex issue. Recently, a number of studies were conducted to investigate mechanisms and interventions of MetS, from different aspects. In this review, the proposed and demonstrated mechanisms of MetS pathogenesis are discussed and summarized. More importantly, different interventions are discussed, so that health practitioners can have a better understanding of the most recent research progress and have available references for their daily practice.

Description: Due to increasing evidence of key chemically mediated interactions in marine ecosystems, a real interest in the characterization of the metabolites involved in such intra and interspecific interactions has emerged over the past decade. Nevertheless, only a small number of studies have succeeded in identifying the chemical structure of compounds of interest. One reason for this low success rate is the small size and extremely polar features of many of these chemical compounds. Indeed, a major challenge in the search for active metabolites is the extraction of small polar compounds from seawater. Yet, a full characterization of those metabolites is necessary to understand the interactions they mediate. In this context, the study presented here aims to provide a methodology for the characterization of highly polar, low molecular weight compounds in a seawater matrix that could provide guidance for marine ecologists in their efforts to identify active metabolites. This methodology was applied to the investigation of the chemical structure of an algicidal compound secreted by the bacteria Shewanella sp. IRI-160 that was previously shown to induce programmed cell death in dinoflagellates. The results suggest that the algicidal effects may be attributed to synergistic effects of small amines (ammonium, 4-aminobutanal) derived from the catabolization of putrescine produced in large quantities (0.05–6.5 fmol/cell) by Shewanella sp. IRI- 160.

Description: The antitumor activity of natural flavonoids has been exhaustively reported. Previously it has been demonstrated that prenylation of flavonoids allows the discovery of new compounds with improved antitumor activity through the activation of caspase-7 activity. The synthesis of twenty-five flavonoids (4–28) with one or more alkyl side chains was carried out. The synthetic approach was based on the reaction with alkyl halide in alkaline medium by microwave (MW) irradiation. The in vitro cell growth inhibitory activity of synthesized compounds was investigated in three human tumor cell lines. Among the tested compounds, derivatives 6, 7, 9, 11, 13, 15, 17, and 18 revealed potent growth inhibitory activity (GI50 〈 10 μM), being the growth inhibitory effect of compound 13 related with a pronounced caspase-7 activation on MCF-7 breast cancer cells and yeasts expressing human caspase-7. A quantitative structure-activity relationship (QSAR) model predicted that hydrophilicity, pattern of ring substitution/shape, and presence of partial negative charged atoms were the descriptors implied in the growth inhibitory effect of synthesized compounds. Docking studies on procaspase-7 allowed predicting the binding of compound 13 to the allosteric site of procaspase-7.

Description: The spectrum and efficacy of available antileishmanial drugs is limited. In the present work we evaluated in vitro the antiproliferative activity of 11 compounds based on tetradentate polyamines compounds against three Leishmania species (L. braziliensis, L. donovani and L. infantum) and the possible mechanism of action. We identified six compounds (3, 5, 6, 7, 8 and 10) effective against all three Leishmania spp both on extracellular and intracellular forms. These six most active leishmanicidal compounds also prevent the infection of host cells. Nevertheless, only compound 7 is targeted against the Leishmania SOD. Meanwhile, on the glucose metabolism the tested compounds have a species-specific effect on Leishmania spp.: L. braziliensis was affected mainly by 10 and 8, L. donovani by 7, and L. infantum by 5 and 3. Finally, the cellular ultrastructure was mainly damaged by 11 in the three Leishmania spp. studied. These identified antileishmania candidates constitute a good alternative treatment and will be further studied.

Description: N-acylhomoserine lactones (AHLs), bacterial signaling compounds involved in quorum-sensing, are a structurally diverse group of compounds. We describe here the identification, synthesis, occurrence and biological activity of a new AHL, N-((2E,5Z)-2,5-dodecadienoyl)homoserine lactone (11) and its isomer N-((3E,5Z)-3,5-dodecadienoyl)homoserine lactone (13), occurring in several Roseobacter group bacteria (Rhodobacteraceae). The analysis of 26 strains revealed the presence of 11 and 13 in six of them originating from the surface of the macroalgae Fucus spiralis or sediments from the North Sea. In addition, 18 other AHLs were detected in 12 strains. Compound identification was performed by GC/MS. Mass spectral analysis revealed a diunsaturated C12 homoserine lactone as structural element of the new AHL. Synthesis of three likely candidate compounds, 11, 13 and N-((2E,4E)-2,4-dodecadienoyl)homoserine lactone (5), revealed the former to be the natural AHLs. Bioactivity test with quorum-sensing reporter strains showed high activity of all three compounds. Therefore, the configuration and stereochemistry of the double bonds in the acyl chain seemed to be unimportant for the activity, although the chains have largely different shapes, solely the chain length determining activity. In combination with previous results with other Roseobacter group bacteria, we could show that there is wide variance between AHL composition within the strains. Furthermore, no association of certain AHLs with different habitats like macroalgal surfaces or sediment could be detected.

Description: Activation of neutrophils is a critically important component of the innate immune response to bacterial and chemical stimuli, and culminates in the “neutrophil burst”, which facilitates neutrophil phagocytosis via the release of superoxide anion radical (O2−) from NADPH oxidase. Excessive and/or prolonged neutrophil activation results in substantial tissue injury and increases in vascular permeability—resulting in sustained tissue infiltration with neutrophils and monocytes, and persistent vasomotor dysfunction. Cardiovascular examples of such changes include acute and chronic systolic and diastolic heart failure (“heart failure with preserved ejection fraction”), and the catecholamine-induced inflammatory disorder takotsubo syndrome. We have recently demonstrated that B-type natriuretic peptide (BNP), acting via inhibition of activation of neutrophil NADPH oxidase, is an important negative modulator of the “neutrophil burst”, though its effectiveness in limiting tissue injury is partially lost in acute heart failure. The potential therapeutic implications of these findings, regarding the development of new means of treating both acute and chronic cardiac injury states, are discussed.

Description: High-performance polymer (HPP)-based engineering materials in tribological applications have been under continuous research over the last few decades. This paper reviewed the recent studies on the sliding wear properties of HPPs and their nanocomposites, which are associated with the intrinsic and extrinsic parameters. In particular, the effects of the intrinsic properties of polymer composites (e.g., mechanical properties of the materials and the types of fillers) and external environmental conditions (e.g., service temperature and lubrication medium) on the formation of transfer layers (TLs) were discussed. The latter would govern the overall friction and wear of polymeric materials in sliding against metallic counterparts. In addition, correlations between the basic mechanical properties of HPPs and their sliding wear behavior were also explored.

Description: Obesity is a complex disease, shaped by both genetic and environmental factors such as diet. In this study, we use untargeted metabolomics and Drosophila melanogaster to model how diet and genotype shape the metabolome of obese phenotypes. We used 16 distinct outbred genotypes of Drosophila larvae raised on normal (ND) and high-fat (HFD) diets, to produce three distinct phenotypic classes; genotypes that stored more triglycerides on a ND relative to the HFD, genotypes that stored more triglycerides on a HFD relative to ND, and genotypes that showed no change in triglyceride storage on either of the two diets. Using untargeted metabolomics we characterized 350 metabolites: 270 with definitive chemical IDs and 80 that were chemically unidentified. Using random forests, we determined metabolites that were important in discriminating between the HFD and ND larvae as well as between the triglyceride phenotypic classes. We found that flies fed on a HFD showed evidence of an increased use of omega fatty acid oxidation pathway, an alternative to the more commonly used beta fatty acid oxidation pathway. Additionally, we observed no correlation between the triglyceride storage phenotype and free fatty acid levels (laurate, caprate, caprylate, caproate), indicating that the distinct metabolic profile of fatty acids in high-fat diet fed Drosophila larvae does not propagate into triglyceride storage differences. However, dipeptides did show moderate differences between the phenotypic classes. We fit Gaussian graphical models (GGMs) of the metabolic profiles for HFD and ND flies to characterize changes in metabolic network structure between the two diets, finding the HFD to have a greater number of edges indicating that metabolome varies more across samples on a HFD. Taken together, these results show that, in the context of obesity, metabolomic profiles under distinct dietary conditions may not be reliable predictors of phenotypic outcomes in a genetically diverse population.

Description: : In this study, effects of pretreatment of corn stover (CS) with sodium hydroxide (NaOH) combined with calcium oxide (CaO) on anaerobic co-digestion of swine manure and CS for biogas production were investigated. Different pretreated-CSs were prepared by adding different doses of NaOH and CaO to CS: Treat-CSA (0.10 g NaOH/g CS), Treat-CSB((0.075 g NaOH + 0.05 g CaO)/g CS), Treat-CSC ((0.05 g NaOH + 0.05 g CaO)/g CS), and Treat-CSD ((0.025 g NaOH + 0.1 g CaO)/g CS). Lignin removal rate, biomass recovery, reduced sugar, methane yield, DT80 (digestion time when biogas achieved 80% of the total biogas), composition of residues, and cost-efficiency were measured to characterize CS after pretreatment and to evaluate the performance of co-digestors fed with swine manure and differently-pretreated CS. The results showed that Treat-CSB showed an excellent lignin removal efficiency and biomass recovery, resulting in the highest methane yield in its co-digestion with swine manure. Since the net benefit of Treat-CSB was calculated to be the highest (i.e., $1.89/ton total solids), therefore, we believe the co-digestion of Treat-CSB and swine manure for biogas production be an effective valorization option for the wastes.

Description: Breakthroughs in Medicinal Chemistry: New Targets and Mechanisms, New Drugs, New Hopes is a series of Editorials, which is published on a biannual basis by the Editorial Board of the Medicinal Chemistry section of the journal Molecules. [...]

Description: The slag’s chromium leaching is one of the most pressing concerns in Electric Arc Furnace (EAF) carbon and stainless steels production. In recent years, many studies have aimed at understanding which properties (basicity, cooling speed) and phases (spinels, wustite, silicates) determine the Cr leaching, defining different indices (sp-factor, cs-factor) in order to forecast the slag’s behavior compared to the leaching of this toxic metal. The literature suggests that spinel formation is usually a good way to fix Cr and prevent its leaching. However, in some conditions (high basicity, low amount of spinel-forming species) soluble Cr-bearing phases can be formed, i.e., Ca-chromite or unstable spinel. In these conditions, Cr can be leached easily, even if it is bound in a spinel structure. In this paper, the effects of basicity and impurities (Ca, Si) on the instability of Cr-spinel was investigated, with respect to slag mesh. The influence of basicity was also studied on Mg-wustite stability, which might contribute to the leaching of Cr. Different samples of carbon steel slag, suspected of forming unstable spinels, belonging to different steel grade production, were also investigated. Both granulated (4 mm) and milled (

Description: Asparagine is one of the important amino acids for long-distance transport of nitrogen (N) in plants. However, little is known about the effect of asparagine on plant development, especially in crops. Here, a new T-DNA insertion mutant, asparagine synthetase 1 (asn1), was isolated and showed a different plant height, root length, and tiller number compared with wild type (WT). In asn1, the amount of asparagine decreased sharply while the total nitrogen (N) absorption was not influenced. In later stages, asn1 showed reduced tiller number, which resulted in suppressed tiller bud outgrowth. The relative expression of many genes involved in the asparagine metabolic pathways declined in accordance with the decreased amino acid concentration. The CRISPR/Cas9 mutant lines of OsASN1 showed similar phenotype with asn1. These results suggest that OsASN1 is involved in the regulation of rice development and is specific for tiller outgrowth.

Description: The Astragalus polysaccharides (APS) are important bioactive components of Astragali Radix, the dry root of Astragalus membranaceus, which has been used in traditional Chinese medicine. In this review, the extraction conditions and extraction rates of APS are first compared for water, microwave-assisted, ultrasonic wave, and enzymatic hydrolysis extraction methods. Some studies have also shown that different methods can be combined to improve the extraction rate of APS. Subsequently, the chemical composition and structure of APS are discussed, as related to the extraction and purification method. Most studies have shown that APS is mainly composed of glucose, in addition to rhamnose, galactose, arabinose, xylose, mannose, glucuronic acid, and galacturonic acid. We also reviewed studies on the modification of APS using chemical methods, including sulfated modification using the chlorosulfonic acid–pyridine method, which is commonly used for chemical modification of APS. Finally, the pharmacological activities and mechanisms of action of APS are summarized, with a special focus on its immunoregulatory, antitumor, anti-inflammatory, and antiviral effects. This review will serve as a valuable resource for the research on APS.

Description: Ethanedithiol-functionalized polyisobutylene was prepared in one step by a photoinitiated thiol-ene “click” reaction starting from ethanedithiol and polyisobutylene (PIB). The functionalized oligomer product was then used as a soluble sequestrant for transition metals. This PIB-bound thioether-thiol ligand is phase selectively soluble in alkanes and it quantitatively sequesters common transition metals like Cu2+ and Pd2+ into an alkane phase, separating them from polar solvents in a biphasic liquid/liquid separation. The chelating thioether-thiol ligand was also successfully used to remove Cu and Pd transition metal catalyst residues from products in crude reaction mixtures in both azide/alkyne click reactions and cross-coupling reactions using a liquid/liquid extraction. Separation efficiencies exceeding 95% and in many cases 99% were achieved.

Description: The Merox process was widely applied in the fine chemical industry to convert mercaptans into disulfides by oxidation with oxygen, including dimethyl disulfide (DMDS). In this paper, a new activated carbon (AC)-supported sulfonated cobalt phthalocyanine (AC-CoPcS) catalyst was prepared through the chemical linkage of ethylenediamine between them. UV−VIS, FT-IR, BET, and XPS were used to characterize the structure of the new catalyst. Then AC-CoPcS was applied to catalyze sodium methylmercaptide (SMM) oxidation for the preparation of DMDS. The effect of process parameters, such as reaction time, catalyst dosage, reaction temperature, and oxygen pressure on SMM conversion per pass (CPPSMM), yield (YieldDMDS), and purity of the DMDS (PurityDMDS) product were investigated to evaluate the catalytic performance of AC-CoPcS. The new supported catalyst exhibits better catalytic performance than the commercial one and can be properly reused four times to obtain CPPSMM and YieldDMDS higher than 90% and 70%. Under the optimum experimental conditions, the CPPSMM and YieldDMDS could reach as high as 98.7% and 86.8%, respectively, and the purity of the DMDS product is as high as 99.8%. This new supported catalyst exhibits good industrial application prospects.

Description: Hydroxyapatite has excellent biocompatibility and osteo-conductivity and, as the main inorganic component of human bones and teeth, is commonly used for bone repair. Its original characteristics can be changed by metal ion substitution. Cobalt ions can act as hypoxia-inducible factors and accelerate bone repair. At the same time, cobalt has paramagnetic properties and is often used in the study of medical imaging and target drugs. Through the introduction of cobalt ions, the unique hydroxyapatite has better biological activity and positioning of medical images. Herein, cobalt-substituted hydroxyapatite (CoHA) was synthesized on the surface of a titanium plate by electrochemical deposition and changes in the power output mode to explore the impact on CoHA. Electrochemical deposition with a pulse current significantly improved the productivity and uniformity of CoHA on the surface of titanium. CoHA show paramagnetic characteristics by a superconducting quantum interference device (SQUID). Resulting smaller particle size and circular morphology improves the magnetic strength of CoHA. Magnetic resonance imaging (MRI) of CoHA showed significant image contrast effect at low concentrations. The calculated particle relaxation rate was higher than other common MRI contrast agents. Biocompatibility of CoHA powder was evaluated using the human osteosarcoma cell line (MG63) which confirmed that CoHA is not cytotoxic and can promote cell growth and extracellular matrix mineralization. With the release of cobalt ions, CoHA was found to be significantly good in repression E. coli indicating about than 95% reduction in bacterial growth. The as-synthesized CoHA has a low degree of crystallinity, highly sensitive image contrast effect, and good bioactivity, and may have potential applications in bone repair and MRI.

Description: In this paper, comparative assessment of failure fatigue lives of thin laminated cementitious composites (LCCs) modeled by two modeling approaches—double-parameter Weibull distribution model and triple-parameter distribution model—was carried out. LCCs were fabricated of ordinary Portland cement (OPC), fly ash cenosphere (FAC), quartz sand, and reinforcing meshes and fibers. The failure fatigue life assessment at various probabilities by the two-parameter model was based on numerical calculations whereas the three-parameter model was applied by an open source program—ProFatigue®. Respective parameters, shape and scale parameters in the two-parameter Weibull distribution model while shape, scale, and location parameters in three-parameter model were determined, and the corresponding probabilistic fatigue lives at various failure probabilities were calculated. It is concluded that the two-parameter model is more accurate in probabilistic fatigue life assessment of double-layer mesh-reinforced LCCs, whereas for single-layer reinforced LCCs, both models could be used at a fair confidence level.

Description: The effect of recrystallization annealing on corrosion behavior of Ta-4%W alloy was studied. It is found that the deformed sample contains high dense dislocations and dislocation boundaries. During annealing, these dislocations and dislocation boundaries are replaced by recrystallizing grains until the alloy is fully recrystallized. Both the anodic dissolution and the cathodic activity is much more blocked. The corrosion potential gradual shift towards negative values and corrosion current density decrease, while polarization resistance increases after annealing, indicating enhanced corrosion resistance of the alloy. Such an enhancement is caused by the increase of low-Σ coincide site lattice boundaries and decrease of dislocations and dislocation boundaries.

Description: Two new members of the [Mn6] family of single-molecule magnets (SMMs) of formulae [Mn6(μ3-O)2(H2N-sao)6(dmf)8](ClO4)2 (1) and [Mn6(μ3-O)2(H2N-sao)6(py)6(EtOH)2][ReO4]2·4EtOH (2), (dmf = N,N′-dimethylformamide, py = pyridine, H2N-saoH2 = salicylamidoxime) have been synthesized and characterized structurally and magnetically. Both compounds were straightforwardly prepared from the deprotonation of the H2N-saoH2 ligand in the presence of the desired manganese salt and solvent (dmf (1) vs. py (2)). Compound 1 crystallizes in the triclinic system with space group Pī and 2 crystallizes in the monoclinic system with space group P21/n. In the crystal packing of 1 and 2, the (ClO4)− (1) and [ReO4]− (2) anions sit between the cationic [Mn6]2+ units, which are H-bonded to –NH2 groups from the salicylamidoxime ligands. The study of the magnetic properties of 1 and 2 revealed ferromagnetic coupling between the MnIII metal ions and the occurrence of slow relaxation of the magnetization, which is a typical feature of single-molecule magnet behavior. The cationic nature of these [Mn6]2+ species suggests that they could be used as suitable building blocks for preparing new magnetic materials exhibiting additional functionalities.

Description: In this paper, a novel approach to facial expression recognition based on the discrete separable shearlet transform (DSST) and normalized mutual information feature selection is proposed. The approach can be divided into five steps. First, all test and training images are preprocessed. Second, DSST is applied to the preprocessed facial expression images, and all the transformation coefficients are obtained as the original feature set. Third, an improved normalized mutual information feature selection is proposed to find the optimal feature subset of the original feature set, thus we can retain the key classification information of the original data. Fourth, the feature extraction and selection of the feature space is reduced by employing linear discriminant analysis. Finally, a support vector machine is used to recognize the expressions. In this study, experimental verification was carried out on four open facial expression databases. The results show that this method can not only improve the recognition rate of facial expressions, but also significantly reduce the computational complexity and improve the system efficiency.

Description: Drought and low phosphorus (P) availability are major limitations for rainfed rice production. Crop roots are important for soil resource acquisition and tolerance to P and water limitations. Two pot and two field trials were conducted to evaluate architectural root responses of contrasting rice varieties to combinations of different levels of P (deficient to non-limiting) and water availability (water stressed to submergence) and to identify the interactions with different varieties. Root development was then related to drought and/or low P tolerance. Although shoot and root growth responded more to P than to water availability, architectural root responses to water were much more prominent than responses to P availability. Reduced water availability decreased nodal thickness and increased secondary root branching, both factors partially enhancing P uptake efficiency and even overcoming a decreased root:shoot ratio under reduced water availability. In contrast to root thickness and secondary branching, basal lateral root density was strongly determined by variety and was related to enhances P uptake. Reduced water availability induces root modifications which—apart from enhancing drought resilience—also affect P uptake efficiency. Future research on rice roots and nutrient uptake may hence take into account the large effects of water on root development.

Description: Arbuscular mycorrhizal fungi (AMF) establish mutualistic symbiotic associations with plant roots and act as biofertilizers by enhancing plant nutrient and water uptake. Moreover, AMF colonization may influence the biosynthesis of plant bioactive compounds in medicinal and aromatic plants. There is limited information on AMF associations with Crocus sativus L. (saffron) roots and their effect on crop performances and spice quality. In the present work we verified the efficiency of root mycorrhization in potted conditions, then we evaluated the yield and quality of the saffron produced in two Alpine sites during two cultivation cycles with the application of AMF. Two inocula were applied, either a single-species (Rhizophagus intraradices) or a multi-species mixture (R. intraradices and Funneliformis mosseae). The trial conducted in potted conditions confirmed that both AMF commercial inocula established symbiotic relationships with saffron roots. The multi-species inoculation yielded the highest content of arbuscules in colonized portions of the root (100%), while the single-species was slightly less (82.9%) and no AMF were recorded in untreated control corms. In open-field conditions, AMF colonization of the root systems, flower production, and saffron yields were monitored, and bioactive compounds contents and antioxidant activity in the dried spice were analysed using spectrophotometry and high performance liquid chromatography. Overall, the saffron produced was high quality (ISO category) and had high contents of bioactive compounds, with very high total polyphenol content and elevated antioxidant activity. The use of arbuscular mycorrhizal symbionts as biostimulants positively affected saffron cultivation, improving the crop performances and the content of important nutraceutical compounds. In particular, the inoculum composed by R. intraradices and F. mosseae increased flower production and the saffron yield. R. intraradices alone enhanced the spice antioxidant activity and the content of bioactive compounds such as picrocrocin, crocin II, and quercitrin. Since saffron is the world’s highest priced spice, the increases in yield and quality obtained using AMF suggests that farms in marginal areas such as alpine sites can increase profitability by inoculating saffron fields with arbuscular mycorrhiza.

Description: 2-(Adamantan-1-yl)-2H-isoindole-1-carbonitrile (1) has been identified as a neurobiological fluorescent ligand that may be used to develop receptor and enzyme binding affinity assays. Compound 1 was synthesized using an optimized microwave irradiation reaction, and crystallized from ethanol. Crystallization occurred in the orthorhombic space group P212121 with unit cell parameters: a = 6.4487(12) Å, b = 13.648(3) Å, c = 16.571(3) Å, V = 1458(5) Å3, Z = 4. Density functional theory (DFT) (B3LYP/6-311++G (d,p)) calculations of 1 were carried out. Results indicated that the optimized geometry was similar to the experimental results, with a root-mean-squared deviation of 0.143 Å. In this paper, frontier molecular orbital energies and net atomic charges are discussed with a focus on potential biological interactions. Docking experiments within the active site of the neuronal nitric oxide synthase (nNOS) protein crystal structure were carried out and analyzed. Important binding interactions between the DFT-optimized structure and amino acids within the nNOS active site were identified that explained the strong NOS binding affinity reported. Fluorescent properties of 1 were studied using aprotic solvents of different polarities. Compound 1 showed the highest fluorescence intensity in polar solvents, with excitation and emission maximum values of 336 nm and 380 nm, respectively.

Description: The global properties of elliptical galaxies are connected through the so-called fundamental plane of ellipticals, which is an empirical relation between their parameters: effective radius, central velocity dispersion and mean surface brightness within the effective radius. We investigated the relation between the parameters of the fundamental plane equation and the parameters of modified gravity potential f ( R ) . With that aim, we compared theoretical predictions for circular velocity in f ( R ) gravity with the corresponding values from a large sample of observed elliptical galaxies. Besides, we consistently reproduced the values of coefficients of the fundamental plane equation as deduced from observations, showing that the photometric quantities like mean surface brightness are related to gravitational parameters. We show that this type of modified gravity, especially its power-law version— R n , is able to reproduce the stellar dynamics in elliptical galaxies. In addition, it is shown that R n gravity fits the observations very well, without the need for a dark matter.

Description: Optical communication is becoming more prevalent in orbit due to the need for increased data throughput. Nanosatellites, which are satellites that typically weigh less than 10 kg, are also becoming more common due to lower launch costs that enable the rapid testing of technology in a space environment. Nanosatellites are cheaper to launch than their larger counterparts and may be a viable option for communicating beyond Earth’s orbit, but have strict Size,Weight, and Power (SWaP) requirements. The Miniature Optical Communication Transceiver (MOCT) is a compact optical transceiver designed to provide modest data rates to SWaP constrained platforms, like nanosatellites. This paper will cover the optical amplifier characterization and simulated performance of the MOCT amplifier design that produces 1 kW peak power pulses and closes three optical links which include Low Earth Orbit (LEO) to Earth, LEO to LEO, and Moon to Earth. Additionally, a benchtop version of the amplifier design was constructed and was able to produce amplified pulses with 1.37 W peak power, including a 35.7% transmit optics loss, at a pump power of 500 mW. Finally, the modulator, seed laser, amplifier, receiver, and time-to-digital converter were all used together to measure the Bit Error Ratio (BER), which was 0.00257 for a received optical peak power of 176 nW.

Description: Recycling waste is important to reduce the production of greenhouse gasses. The aim of this project was to understand determinants of cafeteria waste separation behavior among university students. First, the determinants of waste separation behavior among university students (n = 121) were explored using an online questionnaire. In study 2 (pre-/post-test design), the effect of a small intervention (based on study 1) on actual waste sorting behavior was observed. Finally, a semi-qualitative study in 59 students was conducted as process evaluation of the intervention. The following results were revealed: (1) Students have limited knowledge about waste separation, have a high intention to separate waste, are positive about waste separation in general, and believe that they can separate waste correctly. (2) Just over half of the waste is correctly recycled. An intervention with extra information had no significant effect on improving recycling behavior. (3) Students evaluated the intervention positively. Some students suggested that more information should be available where the actual decision making takes place. Ultimately, this paper concludes that although students have a positive attitude and are willing to behave pro-environmentally, there is a gap between intention and actual behavior. These results may also apply to other organizations and members of those organizations. New interventions are needed to trigger students to make correct waste separation decisions where the actual decision making takes place.

Description: Epidemiological and experimental studies have documented that long-term exposure to fine particulate matter (PM2.5) increases the risk of respiratory diseases. However, the details of the underlying mechanism remain unclear. In this study, male C57BL/6 mice were exposed to ambient PM2.5 (mean daily concentration ~64 µg/m3) for 12 weeks through a “real-world” airborne PM2.5 exposure system. We found that PM2.5 caused severe lung injury in mice as evidenced by histopathological examination. Then, tandem mass tag (TMT) labeling quantitative proteomic technology was performed to analyze protein expression profiling in the lungs from control and PM2.5-exposed mice. A total of 32 proteins were differentially expressed in PM2.5-exposed lungs versus the controls. Among these proteins, 24 and 8 proteins were up- and down-regulated, respectively. Gene ontology analysis indicated that PM2.5 exerts a toxic effect on lungs by affecting multiple biological processes, including oxidoreductase activity, receptor activity, and protein binding. Furthermore, Kyoto Encyclopedia of Genes and Genomes (KEGG) analysis revealed that extracellular matrix (ECM)–receptor interaction, phagosome, small cell lung cancer, and phosphatidylinositol 3-kinase(PI3K)-protein kinase B (Akt) signaling pathways contribute to PM2.5-induced pulmonary fibrosis. Taken together, these results provide a comprehensive proteomics analysis to further understanding of the molecular mechanisms underlying PM2.5-elicited pulmonary disease.

Description: Low-speed streaks in wall-bounded turbulence are the dominant structures in the near-wall turbulent self-sustaining cycle. Existing studies have well characterized their spanwise spacing in the buffer layer and below. Recent studies suggested the existence of these small-scale structures in the higher layer where large-scale structures usually receive more attention. The present study is thus devoted to extending the understanding of the streak spacing to the log layer. An analysis is taken on two-dimensional (2D) wall-parallel velocity fields in a smooth-wall turbulent boundary layer with Ret = 4402400, obtained via either 2D Particle Image Velocimetry (PIV) measurement taken here or public Direct Numerical Simulation (DNS). Morphological-based streak identification analysis yields a Re-independent log-normal distribution of the streak spacing till the upper bound of the log layer, based on which an empirical model is proposed to account for its wall-normal growth. The small-scale part of the spanwise spectra of the streamwise fluctuating velocity below y? = 100 is reasonably restored by a synthetic simulation that distributes elementary streak units based on the proposed empirical streak spacing model, which highlights the physical significance of streaks in shaping the small-scale part of the velocity spectra beyond the buffer layer.

Description: Predicting the exact urban places where crime is most likely to occur is one of the greatest interests for Police Departments. Therefore, the goal of the research presented in this paper is to identify specific urban areas where a crime could happen in Manhattan, NY for every hour of a day. The outputs from this research are the following: (i) predicted land uses that generates the top three most committed crimes in Manhattan, by using machine learning (random forest and logistic regression), (ii) identifying the exact hours when most of the assaults are committed, together with hot spots during these hours, by applying time series and hot spot analysis, (iii) built hourly prediction models for assaults based on the land use, by deploying logistic regression. Assault, as a physical attack on someone, according to criminal law, is identified as the third most committed crime in Manhattan. Land use (residential, commercial, recreational, mixed use etc.) is assigned to every area or lot in Manhattan, determining the actual use or activities within each particular lot. While plotting assaults on the map for every hour, this investigation has identified that the hot spots where assaults occur were ‘moving’ and not confined to specific lots within Manhattan. This raises a number of questions: Why are hot spots of assaults not static in an urban environment? What makes them ‘move’—is it a particular urban pattern? Is the ‘movement’ of hot spots related to human activities during the day and night? Answering these questions helps to build the initial frame for assault prediction within every hour of a day. Knowing a specific land use vulnerability to assault during each exact hour can assist the police departments to allocate forces during those hours in risky areas. For the analysis, the study is using two datasets: a crime dataset with geographical locations of crime, date and time, and a geographic dataset about land uses with land use codes for every lot, each obtained from open databases. The study joins two datasets based on the spatial location and classifies data into 24 classes, based on the time range when the assault occurred. Machine learning methods reveal the effect of land uses on larceny, harassment and assault, the three most committed crimes in Manhattan. Finally, logistic regression provides hourly prediction models and unveils the type of land use where assaults could occur during each hour for both day and night.

Description: Business as usual or transformative change? While the global agro-industrial food system is credited with increasing food production, availability and accessibility, it is also credited with giving birth to ‘new’ challenges such as malnutrition, biodiversity loss, and environmental degradation. We reviewed the potential of underutilized indigenous and traditional crops to bring about a transformative change to South Africa’s food system. South Africa has a dichotomous food system, characterized by a distinct, dominant agro-industrial, and, alternative, informal food system. This dichotomous food system has inadvertently undermined the development of smallholder producers. While the dominant agro-industrial food system has led to improvements in food supply, it has also resulted in significant trade-offs with agro-biodiversity, dietary diversity, environmental sustainability, and socio-economic stability, especially amongst the rural poor. This challenges South Africa’s ability to deliver on sustainable and healthy food systems under environmental change. The review proposes a transdisciplinary approach to mainstreaming underutilized indigenous and traditional crops into the food system, which offers real opportunities for developing a sustainable and healthy food system, while, at the same time, achieving societal goals such as employment creation, wellbeing, and environmental sustainability. This process can be initiated by researchers translating existing evidence for informing policy-makers. Similarly, policy-makers need to acknowledge the divergence in the existing policies, and bring about policy convergence in pursuit of a food system which includes smallholder famers, and where underutilized indigenous and traditional crops are mainstreamed into the South African food system.

Description: Recent discussions on the results of food security programs devote key attention to complex interactions between policy interventions and business innovation for improving nutrition outcomes. This shift from linear approaches of food and nutrition security towards a more interlinked and nested analysis of food systems dynamics has profound implications for the design and organization of research and innovation processes. In this article we outline our experience with interdisciplinary and interactive processes of food systems analysis at different scale levels, paying systematic attention to three critical system interfaces: intersections with other systems, interactions within the food system, and incentives for food system innovations (the so-called: 3I approach). We discuss the importance of these interfaces for leveraging food system adaptation and managing food system transformation. We also provide illustrative examples of the relevance of food systems analysis for the identification of appropriate and effective programs for reinforcing the resilience, responsiveness and inclusiveness of novel food and nutrition programs.

Description: In the present work, we test the mean-variance efficiency that Mexican public pension funds would have shown had these invested their local equity portfolio component only in socially responsible stocks. With a daily simulation (from 1 January 2005 to 31 July 2018) of the Standard & Poors (S&P) Mexico target risk indices, we found that there was no significant difference between the more conservative pension funds that invested only in the Price Index and Quotations (IPC) sustainable index against the ones that invested in the conventional IPC. In the case of the more aggressive type of pension funds (those with a higher Mexican equity investment level), a lower mean-variance efficiency would have been observed had these invested in the IPC sustainable index. We also found, with a two-regime Markov-switching analysis, that socially responsible investment would have been better for most of these pension funds during distress time periods. Even if our results do not give strong short-term proof for the use of a socially responsible investment strategy in the most aggressive pension funds, we found that the benefits will be observed in the long-term, due to a better performance during distress time periods and the lag effect of mid and small-cap stocks in the performance.

Description: Nowadays, manufacturing industry is under increasing pressure to save energy and reduce emissions, and thereby enhancing the energy efficiency of the machining system (MS) through operational methods on the system-level has attracted more attention. Energy-efficient scheduling (ES) has proved to be a typical measure suitable for all shop types, and an energy-efficient mechanism that a machine can be switched off and back on if it waits for a new job for a relatively long period is another proven effective energy-saving measure. Furthermore, their combination has been fully investigated in a single machine, flow shop and job shop, and the improvement in energy efficiency is significant compared with only applying ES for MS. However, whether such two energy-saving measures can be integrated in a flexible job shop environment is a gap in the existing study. To address this, a scheduling method applying an energy-efficient mechanism is proposed for a flexible job shop environment and the corresponding mathematical model, namely the energy-efficient flexible job shop scheduling (EFJSS) model, considering total production energy consumption (EC) and makespan is formulated. Besides, transportation as well as its impact on EC is taken into account in this model for practical application. Furthermore, a solution approach based on the non-dominated sorting genetic algorithm-II (NSGA-II) is adopted, which can avoid the interference of subjective factors and help select a suitable machine for each operation and undertake rational operation sequencing simultaneously. Moreover, experimental results confirm the validity of the improved energy-efficient scheduling approach in a flexible job shop environment and the effectiveness of the solution.

Description: The scientific objective of the study was to identify consumption patterns in one-person households, living independently. The households’ clusters were emerged using Ward’s grouping method. It can be concluded that distinguishing the consumption patterns for one-person households is possible on the basis of diversifying both level and structure of incomes as well as socio-demographic differences between them. Depending on economic and socio-demographic variables, disparate consumption patterns for these types of households can be observed. In addition, it is worth stressing that households have different levels of income (although coming from similar sources) but similar demographic structure show greater similarity than households having similar financial situation. Both the growing number and social significance of one-person households make this research subject useful. This study contributes to understanding differences between consumption in various types of one-person households.

Description: Pervious concretes, as sustainable pavement materials, have great advantages in addressing a number of environmental issues. Fly ash, as the industrial by-product waste, is the most commonly used as cement substitute in concrete. The objective of this paper is to study the effects of waste fly ash on properties of pervious concrete. Fly ash was used to replace cement with equivalent volume method at different levels (3%, 6%, 9%, and 12%). The control pervious concrete and fly ash modified pervious concrete were prepared in the laboratory. The porosity, permeability, compressive strength, flexural strength, and freeze–thaw resistance of all mixtures were tested. The results indicated that the addition of fly ash decreased the early-age (28 d) compressive strength and flexural strength, but the long-term (150 d) compressive strength and flexural strength of fly ash modified pervious concrete were higher than that of the early-age. The adverse effect of fly ash on freeze–thaw resistance of pervious concrete was observed when the fly ash was added. The porosity and permeability of all pervious concrete mixtures changed little with the content of fly ash due to the use of equal volume replacement method. Although fly ash is not positive to the properties of pervious concrete, it is still feasible to apply fly ash as a substitute for cement in pervious concrete.

Description: Compared with developed countries, the paper explores whether non-R&D innovation activities in China actually are effective and provides a guidance on how we can choose a sustainable innovation mode for non-R&D, especially considering the “threshold effect” of the heterogeneity of different regional innovation levels. The dynamic threshold panel models of the non-R&D (NRD) effect on the basis of the threshold of regional innovation level is constructed to verify the complex “threshold effect” characteristics between non-R&D and innovation performance. The empirical results are discussed according to the panel data for 30 provinces in China concerning the high-tech industry. Results argue that the mechanism of non-R&D innovation activities on innovation performance have a significantly different “threshold effect.” Interestingly, when the threshold of regional innovation keeps a low level, the negative effect of non-R&D innovation activities is much larger. When the threshold level of regional innovation increases, reaching the critical mass, the negative impact of non-R&D innovation activities on innovation performance becomes smaller. However, once the regional innovation level crosses the critical mass, the negative impact of non-R&D shows a significantly increasing tendency. Specifically, neither much higher nor much lower regional innovation level is conducive to the promoting effect of non-R&D activities. The negative impact of non-R&D on performance will decrease to the minimum only in the regions within the moderate threshold level (critical mass). The dynamic nonlinear mechanism between non-R&D activities and innovation performance is empirically studied to assist high-tech enterprises for innovation sustainability based on heterogeneity of different regional innovation levels.

Description: Photoplethysmography (PPG) based pulse oximetry devices normally use red and infrared illuminations to obtain oxygen saturation (SpO2) readings. In addition, the presence of motion artefacts severely restricts the utility of pulse oximetry physiological measurements. In the current study, a combination of green and orange illuminations from a multi-wavelength optoelectronic patch sensor (mOEPS) was investigated in order to improve robustness to subjects’ movements in the extraction of SpO2 measurement. The experimental protocol with 31 healthy subjects was divided into two sub-protocols, and was designed to determine SpO2 measurement. The datasets for the first sub-protocol were collected from 15 subjects at rest, with the subjects free to move their hands. The datasets for the second sub-protocol with 16 subjects were collected during cycling and walking exercises. The results showed good agreement with SpO2 measurements (r = 0.98) in both sub-protocols. The outcomes promise a robust and cost-effective approach of physiological monitoring with the prospect of providing health monitoring that does not restrict user physical movements.

Description: The properties of multi-wall carbon nanotubes decorated with iridium oxide nanoparticles (IrOx-MWCNTs) are studied to detect harmful gases such as nitrogen dioxide and ammonia. IrOx nanoparticles were synthetized using a two-step method, based on a hydrolysis and acid condensation growth mechanism. The metal oxide nanoparticles obtained were employed for decorating the sidewalls of carbon nanotubes. Iridium-oxide nanoparticle decorated carbon nanotube material showed higher and more stable responses towards NH3 and NO2 than bare carbon nanotubes under different experimental conditions, establishing the optimal operating temperatures and estimating the limits of detection and quantification. Furthermore, the nanomaterials employed were studied using different morphological and compositional characterization techniques and a gas sensing mechanism is proposed.

Description: With the wide application of wireless sensor networks (WSNs), secure data sharing in networks is becoming a hot research topic and attracting more and more attention. A huge challenge is securely transmitting the data from the source node to the sink node. Except for eavesdropping the information stored in the packages, the adversary may also attempt to analyze the contextual information of the network to locate the source node. In this paper, we proposed a secure data sharing approach to defend against the adversary. Specifically, we first design a secret key mechanism to guarantee the security of package delivery between a pair of nodes. Then, a light-weighted secret sharing scheme is designed to map the original message to a set of shares. Finally, the shares are delivered to the sink node independently based on a proper random routing algorithm. Simulation results illustrate that our approach can defend against the eavesdropping and tracing-back attack in an energy-efficient manner.

Description: The re-initialization of precise point positioning (PPP) can be avoided by cycle slip detection and correction. Ionospheric delay is critical for cycle slip detection and correction, especially for a long data gap. The frequency diversity from GNSS modernization provides the potential for mitigating the impact of ionospheric delay on cycle slip detection and correction. The proposed method constructs the extra-wide lane (EWL), the wide lane (WL), and the narrow lane (NL) epoch-differenced linear combinations based on the ionosphere constrain criterion, so as to determine the undifferenced cycle slips from the cascading ambiguity resolution. The experiment results show that the cycle slips can be fixed correctly even though cycle slips occur in all the available carrier phase observations, and the 3 min data gaps can be merged without high precision positioning continuity loss. The kinematic experiment shows that the instantaneous re-initialization can be achieved with the proposed method.

Description: Time series interferometric synthetic aperture radar SAR (TSInSAR) is one of the most important surface deformation monitoring techniques, and has been widely used in geodesy. Deformation estimation is one of the main steps of TSInSAR processing, so an effective and efficient algorithm is necessary. Present algorithms have some limitations such as computing c osts or errors caused by local extremums. In this work, a novel deformation estimation method based on the simulated annealing (SA) algorithm is proposed to handle this problem. The SA algorithm uses a random search to avoid local extremums and thus can be more likely to get the global optimal solution of deformation. By adopting a better annealing method, this algorithm gets high precision deformation results in less time than most present algorithms. In addition, it can estimate complex nonlinear deformation without adding any computing costs. The results, tested on the real SAR data, confirm the reliability and effectiveness of the SA-based deformation estimation algorithm.

Description: Nowadays, the sensor community has become wireless, increasing their potential and applications. In particular, these emerging technologies are promising for vehicles’ communications (V2V) to dramatically reduce the number of fatal roadway accidents by providing early warnings. The ECMA-368 wireless communication standard has been developed and used in wireless sensor networks and it is also proposed to be used in vehicular networks. It adopts Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) technology to transmit data. However, the large power envelope fluctuation of OFDM signals limits the power efficiency of the High Power Amplifier (HPA) due to nonlinear distortion. This is especially important for mobile broadband wireless and sensors in vehicular networks. Many algorithms have been proposed for solving this drawback. However, complexity and implementations are usually an issue in real developments. In this paper, the implementation of a novel architecture based on multilayer perceptron artificial neural networks on a Field Programmable Gate Array (FPGA) chip is evaluated and some guidelines are drawn suitable for vehicular communications. The proposed implementation improves performance in terms of Peak to Average Power Ratio (PAPR) reduction, distortion and Bit Error Rate (BER) with much lower complexity. Two different chips have been used, namely, Xilinx and Altera and a comparison is also provided. As a conclusion, the proposed implementation allows a minimal consumption of the resources jointly with a higher maximum frequency, higher performance and lower complexity.

Description: Methane (CH4) oxidation is an important process for regulating CH4 emissions from peatlands as it oxidizes CH4 to carbon dioxide (CO2). Our current knowledge about its temporal dynamics and contribution to ecosystem CO2 fluxes is, however, limited due to methodological constraints. Here, we present the first results from a novel method for quantifying in-situ CH4 oxidation at high temporal resolution. Using an automated chamber system, we measured the isotopic signature of heterotrophic respiration (CO2 emissions from vegetation-free plots) at a boreal mire in northern Sweden. Based on these data we calculated CH4 oxidation rates using a two-source isotope mixing model. During the measurement campaign, 74 % of potential CH4 fluxes from vegetation-free plots were oxidized to CO2, and CH4 oxidation contributed 20 ± 2.5 % to heterotrophic respiration corresponding to 10 ± 0.5 % of ecosystem respiration. Furthermore, the contribution of CH4 oxidation to heterotrophic respiration showed a distinct diurnal cycle being negligible during nighttime while contributing up to 35 ± 3.0 % during the daytime. Our results show that CH4 oxidation may represent an important component of the peatland ecosystem respiration and highlight the value of our method for measuring in-situ CH4 oxidation to better understand carbon dynamics in peatlands.

Description: Renewable energy remains an underutilised resource within urban environments. This study examines the ongoing German Energiewende (energy transition) as an example of renewable energy being treated as a necessary resource for urban development. It departs from existing literature by operationalising the Advocacy Coalition Framework (ACF), taking a policy systems approach to analyse (and explain) the cases of three German cities—Munich, Berlin, and Freiburg. This approach helps draw lessons for future UK energy scenarios by placing more abstract conceptions of Sustainable Energy Transitions (SETs) within the context of UK cities, post-Brexit. By discussing five main themes: the shift from government to governance; the need to break ‘carbon lock-in’; renewable energy innovation as an underutilised resource; developing governance strategies for renewable energy resources; the shift from policy to practice, the study yields a detailed reconceptualisation of approaches to renewable energy resource-use policy. The novelty of this study lies in its response to these challenges, taking a policy systems approach to energy governance. The article concludes with a proposed integrated framework. The framework, which is based on multi-scalar and multi-stakeholder integrated energy governance strategy, reconsiders the way in which renewable energy resources are seen in current governance terms in the UK. The framework presents a new approach to renewable energy resource-use policy that embraces innovation, responsible governance, and inclusive processes, (alongside thinking beyond simply technical solutions) to considering the socio-economic impacts of policy decisions in cities.

Description: The Colebrook equation is a popular model for estimating friction loss coefficients in water and gas pipes. The model is implicit in the unknown flow friction factor, f. To date, the captured flow friction factor, f, can be extracted from the logarithmic form analytically only in the term of the Lambert W-function. The purpose of this study is to find an accurate and computationally efficient solution based on the shifted Lambert W-function also known as the Wright ω-function. The Wright ω-function is more suitable because it overcomes the problem with the overflow error by switching the fast growing term, y=W(ex), of the Lambert W-function to series expansions that further can be easily evaluated in computers without causing overflow run-time errors. Although the Colebrook equation transformed through the Lambert W-function is identical to the original expression in terms of accuracy, a further evaluation of the Lambert W-function can be only approximate. Very accurate explicit approximations of the Colebrook equation that contain only one or two logarithms are shown. The final result is an accurate explicit approximation of the Colebrook equation with a relative error of no more than 0.0096%. The presented approximations are in a form suitable for everyday engineering use, and are both accurate and computationally efficient.

Description: In the complex case, the Blaschke group was introduced and studied. It turned out that in the complex case this group plays important role in the construction of analytic wavelets and multiresolution analysis in different analytic function spaces. The extension of the wavelet theory to quaternion variable function spaces would be very beneficial in the solution of many problems in physics. A first step in this direction is to give the quaternionic analogue of the Blaschke group. In this paper we introduce the quaternionic Blaschke group and we study the properties of this group and its subgroups.

Description: Carbon blacks are an extensively used manufactured product. There exist different grades by which the carbon black is classified, based on its purpose and end use. Different properties inherent to the various carbon black types are a result of their production processes. Based on the combustion condition and fuel used, each process results in a carbon black separate from those obtained from other processes. These carbons differ in their aggregate morphology, particle size, and particle nanostructure. Nanostructure is key in determining the material’s behavior in bulk form. A variety of carbon blacks have been analyzed and quantified for their lattice parameters and structure at the nanometer scale, using transmission electron microscopy and custom-developed fringe analysis algorithms, to illustrate differences in nanostructure and their potential relation to observed material properties.

Description: Trans-encoded bacterial regulatory RNAs (sRNAs) are functional analogues of eukaryotic microRNAs (miRNAs). These RNA classes act by base-pairing complementarity with their RNA targets to modulate gene expression (transcription, half-life and/or translation). Based on base-pairing, algorithms predict binding and the impact of small RNAs on targeted-RNAs expression and fate. However, other actors are involved such as RNA binding proteins and epigenetic modifications of the targeted and small RNAs. Post-transcriptional base modifications are widespread in all living organisms where they lower undesired RNA folds through conformation adjustments and influence RNA pairing and stability, especially if remodeling their ends. In bacteria, sRNAs possess RNA modifications either internally (methylation, pseudouridinylation) or at their ends. Nicotinamide adenine dinucleotide were detected at 5′-ends, and polyadenylation can occur at 3′-ends. Eukaryotic miRNAs possess N6-methyladenosine (m6A), A editing into I, and non-templated addition of uridines at their 3′-ends. Biological functions and enzymes involved in those sRNA and micro RNA epigenetic modifications, when known, are presented and challenged.

Description: Understanding and promoting South Korean private forest owners’ investment in the Forest Carbon Offset (FCO) scheme is crucial for enhancing carbon sequestration using forests in South Korea. This study aims to identify the factors of private forest owners associated with the investment decision in FCO projects. A total of 132 forest owners in Geumsan-gun, Chungcheongnam-do responded to a mixed-method survey. A chi-square test on the respondent groups shows that a forest management contract has a positive correlation with the forest owners’ willingness to invest in FCO projects. We also developed a logistic regression model for each forest owner group to estimate the effects of forest characteristics, experience of financial support, forest owner characteristics, and management characteristics on the forest owners’ willingness to invest in FCO projects. The results indicate that beliefs in climate change, size of forest holdings, tree species, stand age, experience in cost-sharing for forestry operations with public agencies, and timber harvest experience were significantly associated with the likelihood of a forest owner’s willingness to invest in FCO projects. Therefore, forest policies should take account of the factors influencing the likelihood of forest owners’ investment in FCO projects. We also found that the forest management contract scheme can be used as a policy instrument for promoting private forest owners’ action for climate change in South Korea.

Description: Wood supply predictions from forest inventories involve two steps. First, it is predicted whether harvests occur on a plot in a given time period. Second, for plots on which harvests are predicted to occur, the harvested volume is predicted. This research addresses this second step. For forests with more than one species and/or forests with trees of varying dimensions, overall harvested volume predictions are not satisfactory and more detailed predictions are required. The study focuses on southwest Germany where diverse forest types are found. Predictions are conducted for plots on which harvests occurred in the 2002–2012 period. For each plot, harvest probabilities of sample trees are predicted and used to derive the harvested volume (m³ over bark in 10 years) per hectare. Random forests (RFs) have become popular prediction models as they define the interactions and relationships of variables in an automatized way. However, their suitability for predicting harvest probabilities for inventory sample trees is questionable and has not yet been examined. Generalized linear mixed models (GLMMs) are suitable in this context as they can account for the nested structure of tree-level data sets (trees nested in plots). It is unclear if RFs can cope with this data structure. This research aims to clarify this question by comparing two RFs—an RF based on conditional inference trees (CTree-RF), and an RF based on classification and regression trees (CART-RF)—with a GLMM. For this purpose, the models were fitted on training data and evaluated on an independent test set. Both RFs achieved better prediction results than the GLMM. Regarding plot-level harvested volumes per ha, they achieved higher variances explained (VEs) and significantly (p 〈 0.05) lower mean absolute residuals when compared to the GLMM. VEs were 0.38 (CTree-RF), 0.37 (CART-RF), and 0.31 (GLMM). Root means squared errors were 138.3, 139.9 and 145.5, respectively. The research demonstrates the suitability and advantages of RFs for predicting harvest decisions on the level of inventory sample trees. RFs can become important components within the generation of business-as-usual wood supply scenarios worldwide as they are able to learn and predict harvest decisions from NFIs in an automatized and self-adapting way. The applied approach is not restricted to specific forests or harvest regimes and delivers detailed species and dimension information for the harvested volumes.

Description: According to the modified Adult Treatment Panel III, five indices are used to define metabolic syndrome (MetS): waist circumference (WC), high blood pressure, fasting glucose, triglycerides (TG), and high-density lipoprotein cholesterol. Our work evaluates the importance of these indices. In addition, we attempted to identify whether trends and patterns existed among young, middle-aged, and older people. Following the analysis, a decision tree algorithm was used to analyze the importance of the five criteria for MetS because the algorithm in question selects the attribute with the highest information gain as the split node. The most important indices are located on the top of the tree, indicating that these indices can effectively distinguish data in a binary tree and the importance of this criterion. That is, the decision tree algorithm specifies the priority of the influence factors. The decision tree algorithm examined four of the five indices because one was excluded. Moreover, the tree structures differed among the three age groups. For example, the first key index for middle-aged and older people was TG whereas for younger people it was WC. Furthermore, the order of the second to fourth indices differed among the groups. Because the key index was identified for each age group, researchers and practitioners could provide different health care strategies for individuals based on age. High-risk middle-aged and healthy older people maintained low values of TG, which might be the most crucial index. When a person can avoid the first and second indices provided by the decision tree, they are at lower risk of MetS. Therefore, this paper provides a data-driven guideline for MetS prevention.

Description: In recent years, intensified industrialization and rapid urbanization have accelerated the accumulation of trace metals in topsoils of the Golden Triangle of Southern Fujian Province in China. Trace metals can cause adverse impacts on ecosystems and human health. In order to assess the ecological and human health risks of trace metals in the Golden Triangle region and to determine the distribution and degree of pollution of trace metals, 456 soil samples were collected from 28 districts. The concentrations of six metals (As, Cr, Cu, Ni, Pb, and Zn) were analyzed to assess ecological risk using the geoaccumulation index (Igeo) and the potential ecological risk index (RI). The United States Environmental Protection Agency (USEPA) model was applied to calculate health risk. The average soil concentrations of the six elements are ranked as follows: As 〈 Ni 〈 Cu 〈 Cr 〈 Pb 〈 Zn. Inverse distance weighting (IDW) interpolation maps showed that Cr, Cu, Ni, and Zn are enriched in the soils of developed areas, while As and Pb are enriched in the soils of undeveloped areas. The Igeo showed that the levels of metals in most soil samples are below polluting levels. Similarly, RI values indicated that trace metals pose low potential ecological risk in the region’s soils. The Hazard Quotient (HQ) ranked the mean total noncarcinogenic risk of the six metals, for both children and adults, as follows: As 〉 Pb 〉 Cr 〉 Ni 〉 Cu 〉Zn. The mean carcinogenic risk (CR) of the metals in the region’s soils are ranked as follows: Cr 〉 As 〉 Ni. The Hazard Index (HI) values indicated that 3.7% of soils contained unsafe levels of toxic metals for children and total carcinogenic risk (TCR) values indicated that 23.3% of soils contained unsafe levels, indicating that children are facing both noncarcinogenic and carcinogenic risks from trace metals. Principal component analysis (PCA) and matrix cluster analysis were used to identify pollution sources and classified trace metals and soil samples into two and five groups, respectively. The five groups represented the effects of different land use types, including agricultural area, residential and public area, industrial area, forest, and industrial area and roadside, based on the contents of trace metals in soils. Industrial, agricultural and traffic activities attribute to the enrichment of Cr, Cu, Ni, Pb, and Zn in the region’s soils. Moreover, the accumulation of As and Pb are also attributed to atmospheric deposition. These results can contribute to a better understanding of pollution, ecological risks, and human health risks from trace metals on large regional scales like the Golden Triangle of Southern Fujian Province.

Description: Environmental tobacco smoke (ETS) and its sequelae are among the largest economic and healthcare burdens in the United States and worldwide. The relationship between active smoking and atherosclerosis is well-described in the literature. However, the specific mechanisms by which ETS influences atherosclerosis are incompletely understood. In this paper, we highlight the definition and chemical constituents of ETS, review the existing literature outlining the effects of ETS on atherogenesis and thrombosis in both animal and human models, and briefly outline the public health implications of ETS based on these data.

Description: Social support is an important predictor of the health of a population. Few studies have analyzed the influence of caregivers’ personal networks from a gender perspective. The aim of this study was to analyze the composition, structure, and function of informal caregiver support networks and to examine gender differences. It also aimed to explore the association between different network characteristics and self-perceived health among caregivers. We performed a social network analysis study using a convenience sample of 25 female and 25 male caregivers. A descriptive analysis of the caregivers and bivariate analyses for associations with self-perceived health were performed. The structural metrics analyzed were density; degree centrality mean; betweenness centrality mean; and number of cliques, components, and isolates. The variability observed in the structure of the networks was not explained by gender. Some significant differences between men and women were observed for network composition and function. Women received help mainly from women with a similar profile to them. Men’s networks were broader and more diverse and they had more help from outside family circles, although these outcomes were not statistically significant. Our results indicate the need to develop strategies that do not reinforce traditional gender roles, but rather encourage a greater sharing of responsibility among all parties.

Description: This study applied a soil water balance (SWB) model to simulate groundwater recharge on Catalina Island, California, for the years 2008–2014, a period that coincided with a severe drought. Island-wide average recharge ranged from 0.05 mm/year in 2013 to 82.3 mm/year in 2008, with a 7-year mean of 23.0 mm/year. High recharge is primarily associated with east-facing mountain fronts and the land cover types “developed, open space” and “herbaceous”. This spatial trend is also reflected in recharge estimates for groundwater well locations produced by the Cl mass balance method. Only in 2008 did all areas of the island experience recharge, while the recharge was very low during the drought years 2009 and 2012–2014. Sensitivity analyses indicate an unresolved discrepancy in land cover classification (i.e., herbaceous grass dominated vs. chaparral and coastal sage dominated) to be a significant factor. In a scenario where herbaceous grass dominates, as field studies from the early 1980s imply, recharge estimates nearly double. Nevertheless, the overall low recharge rates presented herein and the fact that drought conditions in Southern California have worsened since 2014 suggest that large parts of the island may not have received any recharge in nearly a decade.

Description: The present study examines the configuration of an offset jet issuing into a narrow and deep pool. The standard k-ε model with volume-of-fluid (VOF) method was used to simulate the offset jet for three exit offset ratios (OR = 1, 2 and 3), three expansion ratios (ER = 3, 4 and 4.8), and different jet exits (circular and rectangular). The results clearly show significant effects of the circumference of jet exits (Lexit) in the early region of flow development, and a fitted formula is presented to estimate the length of the potential core zone (LPC). Analysis of the flow field for OR = 1 showed that the decay of cross-sectional streamwise maximum mean velocity (Um) in the transition zone could be fitted by power law with the decay rate n decreased from 1.768 to 1.197 as the ER increased, while the decay of Um for OR = 2 or 3 was observed accurately estimated by linear fit. Analysis of the flow field of circular offset jet showed that Um for OR = 2 decayed fastest due to the fact that the main flow could be spread evenly in floor-normal direction. For circular jets, the offset ratio and expansion ratio do not affect the spread of streamwise velocity in the early region of flow development. It was also observed that the absence of sudden expansion of offset jet is analogous to that of a plane offset jet, and the flow pattern is different.

Description: In this study, the use of acorn leaves as a natural coagulant to reduce raw water turbidity and globally improve drinking water quality was investigated. The raw water was collected from a drinking water treatment plant located in Mila (Algeria) with an initial turbidity of 13.0 ± 0.1 NTU. To obtain acorn leaf powder as a coagulant, the acorn leaves were previously cleaned, washed with tap water, dried, ground and then finely sieved. To improve the coagulant activity and, consequently, the turbidity removal efficiency, the fine powder was also preliminarily treated with different solvents, as follows, in order to extract the coagulant agent: (i) distilled water; (ii) solutions of NaCl (0.25; 0.5 and 1 M); (iii) solutions of NaOH (0.025; 0.05 and 0.1 M); and (iv) solutions of HCl (0.025; 0.05 and 0.1 M). Standard Jar Test assays were conducted to evaluate the performance of the coagulant in the different considered operational conditions. Results of the study indicated that at low turbidity (e.g., 13.0 ± 0.1 NTU), the raw acorn leaf powder and those treated with distilled water (DW) were able to decrease the turbidity to 3.69 ± 0.06 and 1.97 ± 0.03 NTU, respectively. The use of sodium chloride solution (AC-NaCl) at 0.5 M resulted in a high turbidity removal efficiency (91.07%) compared to solutions with different concentrations (0.25 and 1 M). Concerning solutions of sodium hydroxide (AC-NaOH) and hydrogen chloride (AC-HCl), the lowest final turbidities of 1.83 ± 0.13 and 0.92 ± 0.02 NTU were obtained when the concentrations of the solutions were set at 0.05 and 0.1 M, respectively. Finally, in this study, other water quality parameters, such as total alkalinity hardness, pH, electrical conductivity and organic matters content, were measured to assess the coagulant performance on drinking water treatment.

Description: The paper presents the results of a study of heavy metals (HMs) concentrations in six retention reservoirs located in the lowland area of western Poland. The objectives of this study were to analyze the Cd, Cr, Cu, Ni, Pb and Zn concentrations, assess contamination and ecological risk, analyze the spatial variability of HM concentrations and identify potential sources and factors determining the concentration and spatial distribution. The bottom sediment pollution by HMs was assessed on the basis of the index of geo-accumulation (Igeo), enrichment factor (EF), pollution load index (PLI) and metal pollution index (MPI). To assess the ecological risk associated with multiple HMs, the mean probable effect concentration (PEC) quotient (Qm-PEC) and the toxic risk index (TRI) were used. In order to determine the similarities and differences between sampling sites in regard to the HM concentration, cluster analysis (CA) was applied. Principal component analysis (PCA) was performed to assess the impact of grain size, total organic matter (TOM) content and sampling site location on HM spatial distribution. Additionally, PCA was used to assess the impact of catchment, reservoir characteristics and hydrological conditions. The values of Igeo, EF, MPI and PLI show that Cd, Cr, Cu, Ni and Pb mainly originate from geogenic sources. In contrast, Zn concentrations come from point sources related to agriculture. The mean PEC quotient (Qm-PEC) and TRI value show that the greatest ecological risk occurred at the inlet to the reservoir and near the dam. The analysis showed that the HMs concentration depends on silt and sand content. However, the Pb, Cu, Cd and Zn concentrations are associated with TOM as well. The relationship between individual HMs and silt was stronger than with TOM. The PCA results indicate that HMs with the exception of Zn originate from geogenic sources—weathering of rock material. However, the Ni concentration may additionally depend on road traffic. The results show that a reservoir with more frequent water exchange has higher HMs concentrations, whereas the Zn concentration in bottom sediments is associated with agricultural point sources.

Description: This work presents an adaptive control of the process of alternating aeration/non-aeration cycles for wastewater treatment. It is aimed at improving nitrogen and phosphorous removal efficiency and reducing energy consumption. It comprises two control levels. The first decides when to switch on and off aeration by comparing the Dissolved Oxygen (DO) and the Oxidation Reduction Potential (ORP) with two activation thresholds. The second, a supervisory control, continuously adapt their values by analyzing the working conditions of the reactor (organic matter and ammonium loads). These working conditions are described by four parameters obtained from the DO and ORP curves: Oxygen Uptake Rate (OUR), Oxygen Rise Average Slope (ORAS), ORParrow and Nitrate and Oxygen Uptake Rate (NOUR). It also adjusts the aeration system power to adapt it to those conditions. This adaptive control has been implemented in a laboratory scale prototype and its performance compared with that provided by another control with fixed thresholds and aeration power implemented in a similar prototype. The adaptive control clearly outperforms that without adaptation in nitrogen and phosphorous removal efficiency and requires lower energy consumption. Similar efficiencies were obtained for organic matter removal (higher than 90% in both cases).

Description: The size effects in metal forming have been found to be crucial in micro-scale plastic deformation or micro-forming processes, which lead to attenuation of the material’s formability due to the increasing heterogeneity of the plastic flow. The use of an electric field during micro-scale plastic deformation has shown to relieve size effects, enhance the material’s formability, modify the microstructure, etc. Consequently, these electric-assisted (EA) micro-forming processes seem to bring many potential benefits that need to be investigated. Accordingly, here we investigated the influence of an electric field on the size effects to describe the fracture behavior in uniaxial micro-tension tests of an AZ31 alloy with various grain sizes. In order to decouple the thermal-mechanical and microstructure changes, room temperature (RT), oven-heated (OH), air-cooled (AC), and EA uniaxial micro-tension tests were conducted. The size effects contribution on the fracture stress and strain showed a similar trend in all the testing configurations. However, the smallest fracture stresses and the largest fracture strains were denoted in the EA configuration. EBSD examination shows that current-induced dynamic recrystallization (DRX) and texture evolution could be negligible under the studied conditions. The kernel average misorientation (KAM) maps give the larger plastic deformation in the EA specimens due to the reduction of plastic micro-heterogeneity. Finally, the fracture morphology indicates that the current-induced ductility enhancement may be attributed to the arrest of micro-crack propagation and the inhibition of void initiation, growth, and coalescence caused by lattice melting and expansion.

Description: Reversible protonic ceramic cells (rPCCs) combine two different operation regimes, fuel cell and electrolysis cell modes, which allow reversible chemical-to-electrical energy conversion at reduced temperatures with high efficiency and performance. Here we present novel technological and materials science approaches, enabling a rPCC with symmetrical functional electrodes to be prepared using a single sintering step. The response of the cell fabricated on the basis of P–N–BCZD|BCZD|PBN–BCZD (where BCZD = BaCe0.5Zr0.3Dy0.2O3−δ, PBN = Pr1.9Ba0.1NiO4+δ, P = Pr2O3, N = Ni) is studied at different temperatures and water vapor partial pressures (pH2O) by means of volt-ampere measurements, electrochemical impedance spectroscopy and distribution of relaxation times analyses. The obtained results demonstrate that symmetrical electrodes exhibit classical mixed-ionic/electronic conducting behavior with no hydration capability at 750 °C; therefore, increasing the pH2O values in both reducing and oxidizing atmospheres leads to some deterioration of their electrochemical activity. At the same time, the electrolytic properties of the BCZD membrane are improved, positively affecting the rPCC’s efficiency. The electrolysis cell mode of the rPCC is found to be more appropriate than the fuel cell mode under highly humidified atmospheres, since its improved performance is determined by the ohmic resistance, which decreases with pH2O increasing.

Description: This research attempted to develop an environmentally-friendly functional building mortar by the combined use of agriculture wastes (agro-wastes) and construction wastes in magnesium oxychloride cement (MOC). The agro-wastes referred to corn stalk (CS) and saw dust (SD), which were used to improve the flexural properties of host cementitious material, whilst the construction wastes referred to recycled clay brick powder (CBP), which was employed to enhance compressive strength and water resistance. Moreover, tourmaline powder (TP) was added as a negative ion-inducing admixture, at a fixed dosage of 10% by weight of MgO, to bestow air-improving functions on the end products. Results showed the flexural strength of MOC was enhanced by the addition of CS and SD. Besides, the incorporation of CBP improved the water resistance in a dosage-dependent way. In addition, the specimens containing CS and SD also had better negative ion-inducing performance due to their higher porosity. Overall, the study provided a feasible and attractive approach to recycle agro- and construction wastes for the production of air purifying mortar. The developed mortar possesses an eco-friendly nature (simultaneous reuse of various waste materials and improvement of the air quality).

Description: Strain hardening cementitious composites (SHCCs) are widely used in projects due to their excellent deformation resistance and large energy absorption capacity. However, determining tensile strain capacity is still a challenge for engineers. The current popular approach is to use inverse methods to predict the tensile behavior of SHCCs, such as the UM method (Qian and Li) and the JCI (Japan Concrete Institute) method. The key to these two approaches is to acquire the exact relationship between the bending and the uniaxial response. In this paper, a reasonable linear constitutive model of the SHCCs is modified. Initially, the moment-curvature diagrams are discussed by material parameters. The results reveal that the moment-curvature response is quite sensitive to the variations in the parameter of transition strain α, post-cracking tensile stiffness η, and strain softening stiffness μ, however, for the compressive parameters, the moment-curvature responses influence on flexural behavior is insignificant. Moreover, the load-deflection curve in the mid-span of SHCC, based on the consideration of shear effect, is simulated under a four-point bending test (FPBT). The results show a remarkable consistency with the experimental data when compared to the previous simulations. It is expected that this modified method can enhance an accurate program in order to obtain the tensile capacity.

Description: The conventional dynamic programming-based track-before-detect (DP-TBD) methods are usually intractable in multi-target scenarios. The adjacent targets may interfere with each other, and the computational complexity is increased with the number of targets. In this paper, a DP-TBD method using parallel computing (PC-DP-TBD) is proposed to solve the above problems. The search region of the proposed PC-DP-TBD is divided into several parts according to the possible target movement direction. The energy integration is carried out independently and parallel in each part. This contributes to reducing the computational complexity in each part, since the divided search region is smaller than the whole one. In addition, the target energy can only be integrated adequately in the part in which the search direction matches the target movement. This is beneficial to improve the ability to detect the targets with various movement directions in different parts with different search directions. The solution to the problem of the adjacent targets interfering with each other is discussed. The procedure of the parallel computing in the proposed PC-DP-TBD is presented in detail. Simulations are conducted to verify the superiority of the proposed PC-DP-TBD in terms of detection probability and computational complexity.

Description: Cutting capacity can be seriously limited in heavy duty face milling processes due to self-excited structural vibrations. Special geometry tools and, specifically, variable pitch milling tools have been extensively used in aeronautic applications with the purpose of removing these detrimental chatter vibrations, where high frequency chatter related to slender tools or thin walls limits productivity. However, the application of this technique in heavy duty face milling operations has not been thoroughly explored. In this paper, a method for the definition of the optimum angles between inserts is presented, based on the optimum pitch angle and the stabilizability diagrams. These diagrams are obtained through the brute force (BF) iterative method, which basically consists of an iterative maximization of the stability by using the semidiscretization method. From the observed results, hints for the selection of the optimum pitch pattern and the optimum values of the angles between inserts are presented. A practical application is implemented and the cutting performance when using an optimized variable pitch tool is assessed. It is concluded that with an optimum selection of the pitch, the material removal rate can be improved up to three times. Finally, the existence of two more different stability lobe families related to the saddle-node and flip type stability losses is demonstrated.

Description: The ways of producing porous-like textured surfaces with chemical etching on aluminum-alloy substrates were studied. The most appropriate etchants, their combination, temperature, and etching time period were explored. The influence of a specifically textured surface on adhesive joints’ strength or superhydrophobic properties was evaluated. The samples were examined with scanning electron microscopy, profilometry, atomic force microscopy, goniometry, and tensile testing. It was found that, with the multistep etching process, the substrate can be effectively modified and textured to the same morphology, regardless of the initial surface roughness. By selecting proper etchants and their sequence one can prepare new types of highly adhesive or even superhydrophobic surfaces.

Description: Advanced engineered surfaces can be used to direct cell behavior. These behaviors are typically characterized using either optical, atomic force, confocal, or electron microscopy; however, most microscopic techniques are generally restricted to observing what’s happening on the “top” side or even the interior of the cell. Our group has focused on engineered surfaces typically reserved for microelectronics as potential surfaces to control cell behavior. These devices allow the exploration of novel substrates including titanium, tungsten, and tantalum intermixed with silicon oxide. Furthermore, these devices allow the exploration of the intricate patterning of surface materials and surface geometries i.e., trenches. Here we present two important advancements in our research: (1) the ability to split a fixed cell through the nucleus using an inexpensive three-point bend micro-cleaving technique and image 3D nanometer scale cellular components using high-resolution scanning electron microscopy; and (2) the observation of nanometer projections from the underbelly of a cell as it sits on top of patterned trenches on our devices. This application of a 3-point cleaving technique to visualize the underbelly of the cell is allowing a new understanding of how cells descend into surface cavities and is providing a new insight on cell migration mechanisms.

Description: A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize the emissions of volatile organic compounds (VOCs); namely, benzene, toluene, ethylbenzene, and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa (SA). Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-h average concentrations (in µg/m3) of benzene, toluene, ethylbenzene, p-xylene, and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 ± 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario was found to be 1.1 and 1.2 respectively, which are 110- and 120-fold higher than the U.S. Environmental Protection Agency (EPA) designated risk severity indicator (1 × 10−6). All four TEX (toluene, ethylbenzene, p-xylene and o-xylene) compounds recorded a Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001 to 0.05, with toluene concentrations being the lowest, and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

Description: In recent years, the study of the factors affecting the carbon trading price plays an important role in promoting the carbon trading markets and the sustainable development of green economy. However, due to the short establishment time of China’s carbon trading market, the carbon trading price data of the pilot markets were not complete and have the typical characteristics of poor information. The traditional grey correlation model cannot effectively identify the volatility and the grey correlation coefficient of trading data. In this paper, an inscribed cored grey relational analysis model (IC-GRA) is constructed by extracting the values of the triangle inscribed center of the time series sample. Through numerical examples and empirical analysis, it is verified that IC-GRA not only satisfies the four axioms of traditional grey correlation but also avoids the influence of outliers of time series fluctuation and improves the discriminability of the grey correlation coefficient. The empirical results of the IC-GRA model in China’s seven pilot carbon trading markets show that: 1. among international carbon trade factor, the biggest influence factor carbon trade price is different in pilot markets. The price of natural gas has a greater correlation with the carbon price of carbon trading markets in Shenzhen, Guangzhou, and Chongqing. The futures price of Certified Emission Reduction (CER) has a strong correlation with the carbon price of Shanghai and Beijing carbon trading markets; the price of Hubei carbon trading market is the largest related to crude oil future price in the New York Mercantile Exchange ( NYMEX). 2. Air Quality Index (AQI) is most relevant to the market carbon price of carbon trading, followed by the trading turnover and trading volume of the carbon trading market. Therefore, studying the carbon trading price of the carbon trading market plays a positive role in improving the sustainable development in those areas.

Description: The Australian mining sector has an elevated industry prevalence of stress and high stress related productivity impairment costs. This study surveyed 897 employees from an Australian mining company to identify characteristics associated with: (a) high stress related productivity impairment costs; and (b) likelihood of stressed employees wanting stress management assistance at work. Groups associated with average annual productivity impairment costs in excess of $50,000 per employee included: permanent day shift employees; employees who reported being stressed at work most of the time; employees who reported being stress at work all of the time; and employees who were contemplating better managing their stress in the next 6 months. Overall, 52% of employees who identified as being in the contemplation stage of change for stress management and 52% of employees who experienced stress most of the time reported wanting stress assistance with stress. However, only 33% of stressed permanent day shift employees and 36% of employees who experienced stress all the time reported wanting stress assistance. To achieve a high return on investment when implementing workplace stress management programs in the mining industry, practitioners need to strategically target health promotion to engage stressed employees with high productivity impairment costs and low desire for stress management assistance.

Description: The innovativeness boosted by incubator centers has an important role in the sustainable development of the country and its regions. The paper describes a comparative analysis of the effectiveness of the business incubator center on the economic growth of a region. The goal of the paper is a comparison between two business incubators, CAN-BE in Hazleton, PA USA and Technopark in Gliwice, Poland. A number of indicators were used to measure economic growth. These selected indicators reflected social, organizational, technical, and financial aspects of economic growth.