ALBERT

Notes: Abstract Specimen thickness is the main experimental factor controlling the results of illite crystallinity (IC) or crystallite size measurements on sedimentation slides. Different values obtained from thick and thin preparations are due to grain-size gradation effects, which may exclude larger and higher ordered grains from contributing to the diffraction. Orientation effects control the measured peak intensity. The change from poor particle orientation in thick slides to high orientation in very thin slides is marked by an increase in specimen density, diminishing non-basal reflections, and by a strong increase in peak intensity. A plateau with constant peak breadths is observed if thin slides of well ordered, platy illites are used. A similar plateau can be recognized for thick preparations of specimens from less ordered materials, but not from well ordered ones. Therefore, it is suggested that IC is determined on very thin sedimentation slides with a thickness of 0.25 mg/cm2 or less. Ultrasonic and H2O2 treatments enhance the degree of particle orientation by destruction of grain aggregates and organic compounds, leading to smaller peak breadths and higher intensities.

Notes: Abstract Five basalt samples from the Point Sal ophiolite, California, were examined using HRTEM and AEM in order to compare observations with interpretations of XRD patterns and microprobe analyses. XRD data from ethylene-glycol-saturated samples indicate the following percentages of chlorite in mixed-layer chlorite–smectite identified for each specimen: (i) L2036 ± 50%, (ii) L2035 ± 70 and 20%, (iii) 1A-13 ± 70%, (iv) 1B-42 ± 70%, and (v) 1B-55 = 100%. Detailed electron microprobe analyses show that ‘chlorite’analyses with high Si, K, Na and Ca contents are the result of interlayering with smectite-like layers. The Fe/(Fe + Mg) ratios of mixed-layer phyllosilicates from Point Sal samples are influenced by the bulk rock composition, not by the percentage of chlorite nor the structure of the phyllosilicate.Measurements of lattice-fringe images indicate that both smectite and chlorite layers are present in the Point Sal samples in abundances similar to those predicted with XRD techniques and that regular alternation of chlorite and smectite occurs at the unit-cell scale. Both 10- and 14-Å layers were recorded with HRTEM and interpreted to be smectite and chlorite, respectively. Regular alternation of chlorite and smectite (24-Å periodicity) occurs in upper lava samples L2036 and 1A-13, and lower lava sample 1B-42 for as many as seven alternations per crystallite with local layer mistakes. Sample L2035 shows disordered alternation of chlorite and smectite, with juxtaposition of smectite-like layers, suggesting that randomly interlayered chlorite (〈0.5)–smectite exists. Images of lower lava sample 1B-55 show predominantly 14-Å layers. Units of 24 Å tend to cluster in what may otherwise appear to be disordered mixtures, suggesting the existence of a corrensite end-member having thermodynamic significance.

Notes: Abstract White mica crystallinity studies have been carried out on 90 samples of mudrocks, six of spotted slate, and five of accretionary lapilli tuff from the area around the Berwyn Hills, North Wales. Strain was measured for some of the spotted slate and tuff samples. The metamorphic grade increases from southeast to northwest, with values of the Kübler index varying from 0.64 to 0.20Δ2θ. Metamorphic zonal boundaries follow the strike of bedding and cleavage, but crystallinity values increase into stratigraphically younger rocks on the northwest side of the Berwyn Dome. This effect is attributed mainly to a rapid increase in the thickness of synmetamorphic overburden to the northwest, comprising exposed Silurian turbidites and inferred Lower Devonian non-marine sediments. Strain variations have a more local influence on crystallinity, and lateral variations in the contemporary geothermal gradient cannot be ruled out. However, only with unrealistically high gradients would the need for a thick Lower Devonian component to the overburden be removed. This reasoning implies that the metamorphic peak was coeval with the Acadian (late Caledonian) event, rather than with an early diastathermal event.

Notes: Abstract Illite crystallinity (IC) measurements, determination of the proportion of 2M mica-polytypes and organic-matter reflectance measurements establish regional diagenetic/low-grade metamorphic trends for the Taconian and Acadian belts of Gaspé Peninsula.IC varies as a function of many factors besides maximum burial temperature and heating time. Correlation between IC and %2M illite polytypes for the Fortin Group and Temiscouata Formation suggests (i) that the amount of high-grade detrital mica in the samples is low, and (ii) that IC can be used with some confidence as an estimator of regional thermal maturation levels. Correlation of these parameters with available organic reflectance values further supports this assumption. The illites of the Temiscouata and western Fortin groups are mostly phengitic in composition, whereas in the eastern outcrop belt they are more Mg- and Fe-rich (celadonitic), but generally also of lower grade and lower 2M content. The d(060) values for illites measured on the unorientated 〈2-μm fraction of samples fall between 1.502 and 1.503 Å (range: 1.500–1.504 Å), indicating relatively low octahedral occupancy by Mg and Fe (between one-fifth and one-third of the available spaces). Pyrophyllite and paragonite were not detected. Chlorites are Fe-rich and ripidolitic.The IC map for the Acadian belt of the peninsula displays general congruence between IC contours (2200 sample points) and structural trends for the 27,000-km2 area. The highest grades (anchimetamorphic) are associated with the oldest rocks (Honorat and Matapedia groups) exposed in the cores of major anticlines. Anchimetamorphic grades associated with the western outcrop belt of the Lower Devonian Fortin Group require 7–8 km of subsidence to accommodate sufficient thickness of overlying younger rocks (on top of 4–5 km of Fortin Group deep-water clastics) to explain the grades in terms of burial metamorphism assuming a geothermal gradient of 30° C km−1. The lowest-grade diagenetic rocks occupy a large area in the northeastern part of the peninsula, smaller areas in the northwestern part of the Acadian belt, in the centre of Chaleurs Bay synclinorium, and in the Ordovician Mictaw Group. The contact between the Taconian and Acadian belt is marked by a distinct maturation discontinuity. The Grand Pabos fault juxtaposes rocks of contrasting maturation levels (Matapedia Group against Fortin Group) in the west, but shows no maturation offset further east in the Honorat Group. The fault zone limiting the Fortin Group in the north is also associated with a major IC jump.

Notes: Abstract The assemblage muscovite-quartz-staurolite-aluminium silicate-biotite-garnet-chlorite with H2O (SABGC assemblage) is invariant in the K2O-FeO-MgO-Al2O3-SiO2-H2O (KFMASH) system. Such five-phase AFM assemblages should be absent in nature, but reported occurrences from at least ten localities suggest that either the assemblage internally controls μH2O or non-KFMASH components stabilize one or more of the phases.Least-squares regression analysis of minerals from South Royalton and Gassetts, Vermont, USA, demonstrates that subsets of the minerals in single SABGC assemblages from both localities are related by balanced reactions involving water. These results are consistent with the interpretation that the subassemblages fixed μH2O at an arbitrary, specified pressure and temperature. Balanced dehydration reactions also may be written between minerals in the SABGC assemblages and four-phase assemblages from the same outcrops interpreted to have equilibrated at the same pressures and temperatures as the five-phase assemblages. These results suggest that different specimens from the same outcrops equilibrated at different values of μH2O, supporting the conclusion that μH2O was not controlled externally. We could not demonstrate internal control of fo2 using measured mineral compositions because oxygen balance occurred in all reactions derived by regression.Regression analysis of published mineral compositions from New Mexico failed to identify balanced reactions involving water or oxygen either among the phases in a single SABGC assemblage or between SABGC and nearby four-phase assemblages. These results demonstrate that neither μH2O nor fo2 were fixed by the SABGC assemblages at these localities, and permit the interpretations that the assemblages were stabilized by the non-KFMASH components Na or Ca and that μH2O and fo2 were controlled externally.

Notes: Abstract Albite porphyroblasts are widely distributed in pelitic and semi-pelitic schists of the Fleur de Lys Supergroup, western Newfoundland. Textures and mineral assemblages indicate that albite grew during nearly isothermal decompression from P-T conditions of about 500° C, 9 kbar, to conditions of 550° C, 6.5 kbar. Three compositional varieties of albite-bearing schists, here termed PMAQ (paragonite-muscovite-albite-quartz), MMAQ (microcline-muscovite-albite-quartz), and PMMQ (paragonite-muscovite-margarite-quartz), can be distinguished on the basis of pre-porphyroblast mineral assemblages. Analysis of these assemblages in terms of the composition of the coexisting fluid [log a(Na+/H+) versus log a(K+/H+)] suggests that, as pressure and temperature changed, the stability field of albite expanded at the expense of coexisting matrix phyllosilicates. This promoted growth of albite on pre-existing or newly formed nuclei. Late oligoclase in PMAQ and PMMQ samples is associated with replacement of matrix garnet by plagioclase + mica ° Chlorite, particularly in strongly sheared samples.

Notes: Abstract Spinel-quartz-cordierite and spinel-quartz are found as relic prograde assemblages in Fe-rich granulites from the Araku area, Eastern Ghats belt, India. Subsequent reactions produced orthopyroxene + sillimanite in the former association and garnet + sillimanite in the latter. The first reaction is univariant in the FMAS system, but is trivariant in the present case because of the presence of Zn and Fe3+ in spinel. The second reaction also has high variance because of Zn and Fe3+, but also because of the presence of Ca in garnet. Thermobarometry shows that the metamorphic conditions were approximately 950° C and 8.5 kbar and the fo2 was near the NNO buffer. In Fe-rich bulk compositions and low-P-high-T conditions of metamorphism, two of the univariant reactions around the invariant point [Sa], namely (Sa, Hy) and (Sa, Cd), change topology due to reverse partitioning of Fe-Mg between coexisting garnet and spinel. An alternative partial petrogenetic grid in the system FMAS is constructed for such conditions and is applied satisfactorily to several sapphirine-free spinel granulites. It is shown that bulk composition (XFe and Zn) exerts greater control on the stability of spinel + quartz than fo2. The effect of the presence of Zn and Fe3+ in spinel on the proposed grid is evaluated. Reaction textures in the Araku spinel granulites can be explained from the petrogenetic grid as due to near-isobaric cooling.

Notes: The impure marbles of the internal Sesia-Lanzo Zone underwent a multi-stage metamorphic evolution of Alpine age and retain early-Alpine eclogitic assemblages, partially recrystallized under blueschist to greenschist facies conditions. These high-P assemblages consist of carbonates, phengite, quartz, omphacite, grossular-rich (locally spessartinic) garnet, zoisite and Al-rich titanite. Retrogressive stages are characterized by the growth of glaucophane, paragonite, phlogopite, tremolite and albite. Halogen-rich biotite and amphibole are also present. P-T estimates of the early-Alpine metamophism have been calculated from these unique high-P assemblages, in order to test the applicability of some calibrations to impure carbonate systems. In particular, some Gt-Cpx calibrations and the phengite geobarometer give results (T= 575 ± 45° C at 15 kbar for the eclogitic climax and T≤ 500° C at PH2O ≤ 9 kbar for early-Alpine retrogressive stages) which are within the range obtained from the surrounding lithologies.Phase relationships in P-T-XCO2 space indicate that mineral assemblages in the impure marbles coexisted with H2O-rich fluids (XCO2 〈0.03) during their entire Alpine evolution.

Notes: Petrographical and mineral chemical data are given for the eclogites which occur in the garnet-kyanite micaschists of the Penninic Dora-Maira Massif between Brossasco, Isasca and Martiniana (Italian Western Alps) and for a sodic whiteschist associated with the pyrope-coesite whiteschists of Martiniana. The Brossasco-Isasca (BI) eclogites are fine grained, foliated and often mica-rich rocks with a strong preferred orientation of omphacite crystals and white micas. Porphyroblasts of hornblende are common in some varieties, whilst zoisite and kyanite occur occasionally in pale green varieties associated with leucocratic layers with quartz, jadeite and garnet. These features differentiate the BI eclogites from the eclogites that occur in other continental units of the Western Alps, which all belong to type C. Garnet, sodic pyroxene and glaucophane are the major minerals in the sodic whiteschist.Sodic pyroxene in the eclogites is an omphacite often close to Jd50Di50, with very little acmite and virtually no AlIV, and impure jadeite in the leucocratic layers and in the sodic whiteschist. Garnet is almandine with 20–30 mol. % for each of the pyrope and grossular components in the eclogites and a pyrope-rich variety in the sodic whiteschist. White mica is a variably substituted phengite, and paragonite apparently only occurs as a replacement product of kyanite. Amphibole is hornblende in the eclogites, but the most magnesian glaucophane yet described in the sodic whiteschist. Quartz pseudomorphs of coesite were found occasionally in a few pyroxenes and garnets.The P-T conditions during the VHP event are constrained in the eclogites by reactions which define a field ranging from 27–28 kbar to 35 kbar and from 680 to 750° C. These temperatures are consistent with the results of garnet-pyroxene and garnet-phengite geothermometry which suggest that the eclogites may have equilibrated at around 700° C. In the sodic whiteschist pressures ranging from 29 to 35 kbar can be deduced from the stability of the jadeite-pyrope garnet-glaucophane compatibility. As in the eclogites water activity must have been low. Such conditions are close to the P-T values estimated for the early Alpine recrystallization of the pyrope-coesite rock and, like petrographical and mineralogical features, set aside the BI eclogites from the other eclogites of the Western Alps, instead indicating a close similarity to some of the eclogite bodies occurring in the Adula nappe of the Central Alps. An important corollary is that glaucophane stability, at least in Na- and Mg-rich compositions and under very high pressures, may extend up to 700° C, in agreement with the HT stability limit suggested by experimental studies.

Notes: The retrograde P-T trajectory of the eclogitic Fe-Ti-gabbros from the Ligurian Alps is constrained by the appearance of mineral parageneses post-dating the Na-clinopyroxene + garnet eclogitic assemblage and indicating the following sequence of metamorphic events: (1) amphibolitic stage— edenite/katophorite + plagioclase (An33–43) + oxides in symplectitic aggregates; (2) glaucophanic stage— a porphyroblastic glaucophanic amphibole has overgrown the symplectite, winchite also occurs as thin rims around glaucophane and both amphiboles are, sometimes, armoured by atoll garnets; (3) albite-amphibolite stage—barroisite/katophorite + albite + epidote + oxides ± chlorite overprint the glaucophanic stage minerals; (4) greenschist stage—represented by actinolite + albite + epidote + oxide paragenesis.The metamorphic evolution is complex and the decompression path, on a P–T diagram, is significantly different from those defined in the literature for the Voltri eclogites. The main features inferred from the P–T path are the following: (1) the pressure climax does not match the thermal climax, the maximum temperature conditions are in fact achieved during the early stage of uplift; (2) a decrease in temperature, suggested by the appearance of glaucophane after the amphibolitic symplectite; (3) successive uplift, probably accompanied by an increase in temperature. The complexity of the P-T path drawn for the Voltri eclogites can be explained with a mechanism of successive underthrusts propagating from the innermost to the outermost sector of the Ligurian Alps.

Notes: CO2–CH4 fluid inclusions are present in anatectic layer-parallel leucosomes from graphite-bearing metasedimentary rocks in the Skagit migmatite complex, North Cascades, Washington. Petrological evidence and additional fluid inclusion observations indicate, however, that the Skagit Gneiss was infiltrated by a water-rich fluid during high-temperature metamorphism and migmatization.CO2-rich fluid inclusions have not been observed in Skagit metasedimentary mesosomes or melanosomes, meta-igneous migmatites, or unmigmatized rocks, and are absent from subsolidus leucosomes in metasedimentary migmatites. The observation that CO2-rich inclusions are present only in leucosomes interpreted to be anatectic based on independent mineralogical and chemical criteria suggests that their formation is related to migmatization by partial melting. Although some post-entrapment modification of fluid inclusion composition may have occurred during decompression and deformation, the generation of the CO2-rich fluid is attributed to water-saturated partial melting of graphitic metasedimentary rocks by a reaction such as biotite + plagioclase + quartz + graphite ± Al2SiO5+ water-rich fluid = garnet + melt + CO2–CH4. The presence of CO2-rich fluid inclusions in leucosomes may therefore be an indication that these leucosomes formed by anatexis.Based on the inferences that (1) an influx of fluid triggered partial melting, and (2) some episodes of fluid inclusion trapping are related to migmatization by anatexis, it is concluded that a free fluid was present at some time during high-temperature metamorphism. The infiltrating fluid was a water-rich fluid that may have been derived from nearby crystallizing plutons. Because partial melting took place at pressures of at least 5 kbar, abundant free fluid may have been present in the crust during orogenesis at depths of at least 15 km.

Notes: The solid-solid reaction magnesiocarpholite = sudoite + quartz has been bracketed between 350 and 500°C, 6.3 and 7.8 kbar. Because it is impossible to synthesize end-member sudoite, all experiments were carried out using natural minerals as starting materials. Although mineral compositions were very close to those of the end-members, the effect of the fluorine content in carpholite was significant. Particularly in those experiments where sudoite grows at the expense of carpholite, electron microprobe analysis of the run products shows that a more stable F-rich carpholite crystallizes too, and consumes the fluorine released in solution by the breakdown of the original carpholite.Our experimental results are combined, through a thermodynamic analysis, with a previous data set and with previous experimental data concerning the relative stability of chlorite, talc and magnesiocarpholite with excess of quartz and water as a function of P–T and AlAl(SiMg)-1 substitutions in phyllosilicates. This allows us to constrain the feasible thermodynamic parameters (H°f, sud; S° sud) and (H°f,car; S°car) for the Mg end-members. Using the partition coefficients calculated from natural parageneses, we have computed a petrogenetic grid for the system FeO–MgO–Al2O3–SiO2–H2O. It demonstrates that parageneses involving sudoite and carpholite can be used as indicators of P–T conditions, up to 600° C, 8 kbar for sudoite, and at higher pressure for carpholite.

Notes: Regional-scale mapping of index-mineral isograds in mafic units of the early Proterozoic Cape Smith Thrust Belt (northern Québec) has revealed contrasting pressure-temperature regimes associated with two distinct structural domains. In the southern domain, crustal thickening was accomplished by early, piggy-back thrust faults. Isograds cross-cut the thrusts, indicating that thermal-peak mineral growth outlasted deformation associated with early imbrication. Mineral zones are: (1) actinolite (Act) + albite (Alb); (2) hornblende (Hbl) + Act + Alb; (3) Hbl + Act + oligoclase (Oli); (4) Hbl + Oli; and (5) garnet (Grt) or clinopyroxene + Hbl + Oli-andesine. The oligoclase isograd occurs at higher grade than the hornblende isograd, a sequence typical of medium-pressure terranes (5–7 kbar). An Hbl-Alb bathograd. calibrated from mixed-volatile equilibria in the NCMASH-CO2 model system, suggests minimum pressures of about 5.4 kbar.Metamorphism in the northern domain was a consequence of re-imbrication, by means of out-of-sequence thrust faults active during and after peak metamorphic conditions. Mineral growth was coeval with thrusting, as documented by the syn-kinematic garnet porphyroblasts. Compared to the southern domain, a different sequence of isograds in mafic rocks shows that the albite-oligoclase transition takes place in the garnet zone. Based on thermobarometry in garnet-hornblende rocks, the oligoclase isograd occurs in a temperature range of 525–600°C, typical of high-pressure terranes (7–10 kbar). Calibrated bathograds for the Hbl-Ms-Alb and Grt-Alb bathozonal assemblages, respectively in the KNCMASH-CO2 and NCMASH model systems, indicate minimum pressures in the northern domain of 6.7 and 8.5 kbar. Higher-pressure series for this domain are explained by out-of-sequence thrusts exposing deeper crustal levels. For similar structural levels, only minor amounts of syn-deformational uplift (1–2 kbar and 50–75°C) are recorded in metabasites of this domain, compared to results in adjacent metapelites of the area (essentially isothermal uplift of 3–5 kbar).RESUME La bande du Cap Smith (nord du Québec) est une ceinture de chevauchement d'ǎge protérozoique inférieur, dominée par des roches mafiques. La cartographie d'isogrades à minéraux indicateurs dans les unités mafiques de la ceinture a révelé deux régimes contrastes de pression–température, chacun associéà des épisodes distincts d'épaississement crustal. Dans le domaine sud, des failles de chevauchement en-série sont responsables pour l'empilement tectonique. Les isogrades recoupent les failles, indiquant que l'apogée thermale a suivi l'emplacement initial des nappes de charriage. Les zones minérales sont: (1) actinote (Act) + albite (Alb); 2) hornblende (Hbl) + Act + Alb; (3) Hbl + Act + oligoclase (Oli); 4) Hbl + Oli; et (5) grenat (Grt) où clinopyroxene + Hbl + Oli-andésine. L'isograde d'oligoclase apparaǐt à plus haute température que l'isograde d'hornblende, une séquence typique des terrains de pressions moyennes. Un bathograde Hbl–Alb, calibréà partir d'équilibre mixte de volatiles dans le système NCMASH–CO2, suggère des pressions minimales d'environ 5.4 kbar.Le métamorphisme dans le domaine nord de la ceinture a été le résultat d'une réimbrication, causé par des chevauchements hors-série actifs pendant et après l'apogée thermale. La croissance minérale fǔt synchrone au chevauchement, documentée par des porphyroblastes de grenat syn-cinénatique. Comparé au domaine sud, une différente séquence d'isogrades dans les métabasaltes montre que la transition albite–oligoclase se situé dans la zone à grenat. Par la thermobarométrie dans les roches à grenat–hornblende l'isograde d'oligoclase se situe dans un écart de température de 525–600°C, typique des terrains de hautes pressions (7–10 kbar). Des bathogrades calibrés pour les assemblages bathozonales Hbl–Ms–Alb et Grt–Alb, rcspectivement dans les systèmes KNCMASH–CO2 et NCMASH, indique des pression minimales pour le domaine nord de 6.7 et 8.5 kbar. Une zonégraphie à plus haute pression pour ce domaine est expliquée par des chevauchements hors-série exposant des niveaux plus inférieurs de la croǔte imbriqué. Pour des niveaux structuraux similaries, des soulèvements syn-métamorphiques mineurs sont enregistrés dans les métabasaltes (1–2 kbar et 50–75°C), comparés aux métapélites adjacentes avec un soulèvement (essentially isothermal uplift of 3–5 kbar.

Notes: Mid-Cretaceous granulite gneisses crop out in a narrow belt in the Cucamonga region of the south-eastern foothills of the San Gabriel Mountains, southern California. Interlayered mafic granulites and pelitic, carbonate, calc-silicate and quartzofeldspathic metasediments record hornblende granulite subfacies metamorphism at approximately 8 kbar and 700–800°C. Regional deformation and formation of banded gneisses ceased by c. 108 Ma. although mafic-intermediate magmatism and high-grade metamorphism continued locally as late as c. 88 Ma. Garnet zoning in metapelitic gneisses suggests that peak metamorphism was followed locally by a period of near-isobaric cooling, but this interpretation requires diachronous cooling of the granulite belt which cannot be demonstrated without detailed thermo-chronological data. It is more likely that the entire terrane remained at granulite facies P–T conditions until 88 Ma, followed by rapid uplift associated with juxtaposition against adjacent middle and upper crustal arc terranes. Uplift occurred between c. 88 and 78 Ma at rates of approximately 1–2 km Ma-1. The geotectonic evolution of the Cucamonga granulites is similar to mid-Cretaceous high-P granulites in the Sierra Nevada and Salinian block of central California. Late Cretaceous uplift common to these granulites may provide an important tectonic link between dismembered Mesozoic batholithic terranes in the California Cordillera.

Notes: In this paper we analyze the properties of price equilibria in a duopoly market where firms sell vertically differentiated products, consumers being uncertain about which firm sells which quality. Both existence and properties of price equilibria are characterized by the beliefs of the consumers' population about the distribution of quality between firms.

Notes: The survey classifies economic theories of the firm into four categories based on the level of aggregation in economic models: (1) neoclassical, (2) industrial organization, (3) contractual, and (4) organizational incentive. Economic theories of the firm are evaluated on the basis of their potential application to problems of management decision making. The survey suggests that a management perspective can be useful in developing an integrated theoretical analysis of the firm that addresses both competitive strategy and organizational design.

Notes: Commitment: The Dynamic of Strategy, by Pankaj Ghemawat.Ghemawat's Commitment makes recent results in game-theoretic industrial organization accessible and useful to practitioners in the field of strategic management. This book contributes to the management strategy literature on two levels. On a conceptual level, Ghemawat strives to isolate “commitment” as the sole explanation of persistent differences in firm performance. On a more pragmatic level, he provides a framework intended to aid managers in making commitment-intensive decisions. It is with respect to how well he achieves these two distinct goals that I evaluate Ghemawat's contribution. In addition, I review briefly the book's content, and I compare Ghemawat's approach to some alternative approaches familiar to scholars and practitioners of strategic management.

Notes: In the present paper, we relate the extent of job security offered to incumbent managers to the extent of competition among firms in the product market, where the extent of job security is measured by the probability that an incumbent manager continues to be employed by his current firm and the extent of competition is measured by the degree of differentiation between competing brands. We demonstrate that when competition between firms intensifies and “on-the-job training” is relatively more conducive to reducing the variable costs of production, firms tend to offer reduced (increased) job security to incumbent managers, provided that the degree of differentiation between competing products is sufficiently large (small), respectively. If “on-the-job training” is relatively more conducive to reducing the fixed costs of production, however, the previous result is reversed.

Notes: This paper presents a model of strategic product choice when consumer preferences combine features of both horizontal and vertical product differentiation. Consumers disagree on what amount of a “special” characteristic makes for a better product, but those who prefer more of this attribute are willing to pay more for it. Within this demand structure, I examine the advantages of first-mover firms. I find that such firms typically do best in markets where the maximum degree of product differentiation is limited by preferences rather than technology. These are “niche markets”. Follower firms do better in markets in which the range of preferences is broad relative to the span of feasible goods.

Notes: This paper reexamines Grossman and Hart's (1980) insight into how the free-rider problem excludes an external raider from capturing the increase in value it brings to R firm The inability of the raider to capture any of the surplus depends critically on the assumption of equal and indivisible shareholdings–the one-share-per-shareholder model In contrast, we show that once shareholdings are large and potentially unequal, a raider may capture a significant part of the increase in value Specifically, the free-rider problem does not prevent the takeover process when shareholdings are divisible.

Notes: We analyze the implementation problem faced by firms when trying to collude in the face of asymmetric information about costs. Assuming that transfer payments are possible, we examine the incentive compatibility and individual rationality constraints that must be satisfied by any cartel agreement. Two scenarios are considered. Firms may or may not withdraw from the agreement after each firm's costs become known. If no withdrawal is possible, we find that the monopoly rule is implementable when weak types of individual rationality constraints are required. This contrasts with some results in the literature. If withdrawal is possible, we find a potential conflict between different forms of individual rationality constraints, in particular, between interim and ex post constraints. This conflict disappears in industries with a large number of firms.

Notes: This paper offers a general characterization of the optimal product line prices for a monopolist whose quality of products is initially unknown to consumers. In the focal equilibrium, a monopolist signals a high-quality product line by pricing as if quality were known to be high, but costs of production were higher than they truly are. In a rich set of environments, this characterization implies that the prices of all products are initially distorted upward, with the price distortion being largest for products with the most inelastic demands and/or quality-sensitive production costs. These implications yield predictions for the time path of prices flint are broadly consistent with evidence from the marketing literature. The multidimensional signaling problem is made tractable by the satisfaction of a very simple and powerful single crossing property.

Notes: Managerial behavior that is rational and profit-maximizing sometimes will seem to be overly conservative. If the valuation of innovations contains white noise and the status quo would be preferred to random innovation, then any innovation that does not appear substantially better than the status quo should be rejected, for reasons arising from regression toward the mean. The more successful the firm, the higher is the optimal acceptance threshold and conservative bias. Other things equal, more successful firms will spend less on research, adopt fewer innovations, and be less likely to advance the industry's best practice.

Notes: Identical cases of wine are often auctioned one immediately after another. Ashenfelter (1989) reports that on average, the later lots fetch less. Such a systematic price difference seems anomalous, the more so because it is shown here that rational expectations imply not equal, but rising, prices. Risk aversion is an obvious way of reconciling the evidence with rational behavior. There is an alternative explanation. The auctions observed by Ashenfelter involved a buyer's option, whereby the first-round winner could purchase further cases at the same price. It is shown that this feature may both account for the observed price trajectory and raise seller revenue.

Notes: This paper examines the incentives for integration when the market for consumer durables (hardware) is oligopolistic and the market for complementary services (software) is monopolistically competitive. We find that the equilibrium industry structure will depend on the magnitude of the fixed costs of software development. If the software development costs are relatively large, the equilibrium industry structure is unintegrated, that is, neither hardware firm integrates; if the software development costs are relatively small, the equilibrium industry structure is integrated, that is, both hardware firms integrate. Under the integrated industry structure, hardware profits are lower, less varieties are provided, and hardware prices are lower than under the unintegrated industry structure. The game has a prisoners' dilemma structure when the software development costs are relatively small because of a foreclosure effect. Strategically increasing the number of software varieties provides an avenue for an integrated hardware firm to increase its market share and profits by reducing the number of software varieties available for an unintegrated rival technology. Although consumer surplus is higher under an integrated industry structure, the total surplus associated with the unintegrated industry structure exceeds that of the integrated industry structure.

Notes: Price setting by firms and search by customers is analyzed, relaxing two basic attributes of most search models: price precommitment and agent heterogeneity. Customers are characterized by individual demand functions for a homogeneous good and can choose to employ a threat to search. Firms noncooperatively make pricing decisions by using the individual demand curves under conditions of constant marginal cost. Firms adopt pricing rules that optimally respond to customer search histories. Bargaining power is endogenously assigned. Firms know their common marginal cost; customers, the cost distribution. The unique separating equilibrium is characterized by a lumpy distribution of prices and by heterogeneous shopping behavior by customers giving rise to “shoppers” and “nonshoppers”

Notes: Most research on product positioning supports the idea of differentiation. Product standardization (i.e., minimum differentiation) occurs only under very limiting assumptions. Yet, similar products are often observed in the marketplace. We attempt to restore the case for standardization by using more realistic assumptions than in previous work. We assume that consumers consider not only observable attributes in brand choice, but also attributes that are unobservable by the firms. We find that standardization is an equilibrium when consumers exhibit sufficient heterogeneity along the unobservable attributes under both positioning with exogenously given prices and price competition, We also show that, under insufficient heterogeneity along the unobservable attribute, our results coincide with past research that argues in favor of differentiation.

Notes: This paper proposes an empirical methodology for studying various (implicit or explicit) collusive behaviors on two strategic variables, which are price and advertising, in a differentiated market dominated by a duopoly. In addition to Nash or Stackelberg behaviors, we consider collusion on both variables, collusion on one variable and competition on the other, etc. Using data on the Coca-Cola and Pepsi-Cola markets from 1968 to 1986, full information maximum likelihood estimation of cost and demand functions are obtained allowing for various collusive behaviors. The collusive hypothesis is not rejected, and the best form of collusive behavior is selected via nonnested testing procedures. Using the best model, Lerner indices are computed for both duopolists to provide summary measures of market power. Finally, our approach is contrasted with the conjectural variation approach and is shown to give superior results.

Notes: The microstructures in the Erro-Tobbio peridotite indicate several stages of recrystallization of olivine + titanian clinohumite-bearing assemblages. The development of these assemblages is closely associated with serpentinite mylonites, in which they occur in shear bands and foliations and are inferred to have grown synkinematically, in veins, and as post-kinematic radial aggregates. In the peridotite wall-rock adjacent to these mylonites, the same assemblages have recrystallized statically at the expense of original olivine and pyroxenes, mesh-textured chrysolite and antigorite veins. In addition, the olivine-bearing assemblage occurs in widespread vein systems. The brittle deformation of the peridotite resulting in the development of these vein systems is closely related to ductile deformation of metagabbroic dykes in the peridotite. Although early metasomatism resulted in extensive rodingitization of the gabbros, some dykes show an eclogitic assemblage of Na-clinopyroxene + garnet + chloritoid + chlorite ± talc. These observations, the microstructures and the mineral chemistry all suggest that the assemblages in the ultramafic rocks and metagabbros developed during a prograde evolution towards high pressures (〉13–16 kbar, 450–550° C), and during subsequent decompression. This metamorphic evolution is considered to be related to Late Cretaceous intraoceanic subduction in the Alps-Apennine system and closure of the Piedmont-Ligurian basin.

Notes: Abstract In well NJ-15 of the Nesjavellir geothermal field, Iceland, the transition of discrete smectite into discrete chlorite has been studied from drill cuttings recovered at depths of less than 1714 m and over a continuous range of temperatures between 60 and 300° C. At temperatures below 180° C, the clay fractions contain mixtures of di- and trioctahedral smectites, whose layer charge increases with depth. Between 200 and 240° C, discrete smectites have transformed into smectite-rich, randomly interstratified chlorite and smecite (R0 C/S). Because the abundance of chlorite interlayers in this C/S is generally 〈20%, its presence can be detected only by electron microprobe techniques and not by X-ray diffraction. Between 245 and 265° C, both regularly (R1) and randomly interstratified C/S are the predominant layer silicates. Discrete chlorite first appears at approximately 270° C and coexists with minor amounts of R0 C/S at higher temperatures. R0 and R1 C/S form a nearly complete compositional series between trioctahedral saponite and discrete chlorite end-members. The interlayer cation and Si content of smectites and C/S decrease with increasing temperature. The Mg/(Mg + Fe) content of smectite, C/S, and chlorite is unrelated to temperature. The percentage of chlorite in C/S, as determined by electron microprobe analyses, increases continuously with increasing temperature, except for occurrences of smectite-rich C/S in fresh basaltic dykes which have not thermally equilibrated with the higher grade country rocks.

Notes: Abstract Fairly strong (r= 0.75–0.85) positive linear correlations were found between crystallinity indices (peak widths) measured on the first two basal reflections of chlorite and those of illite–muscovite in 〈2-μm fractions of a representative shale–slate–phyllite series from Palaeozoic and Mesozoic formations of northeast Hungary. The metamorphic grade ranges from late or deep diagenesis through anchizone to epizone conditions. Chlorite crystallinity values measured on air-dried and ethylene-glycol-solvated samples suggest that the effects of expandable interlayers are negligable, especially in the higher grade (∼temperature) part of the series. However, the greater scattering of crystallinity values for the chlorite 001 reflection compared to those of the 002 reflection may be related to the effects of minor amounts of interlayered and/or discrete smectite and/or vermiculite. With increasing metamorphic grade and advancing equilibrium recrystallization, the chlorite compositions in different samples become more homogenous. No correlation exists between crystallinity and changes in chlorite composition as estimated from the intensity ratios of basal reflections. Hence an increase of domain size and a decrease of lattice distortion with increasing grade (∼temperature) may be decisive factors affecting chlorite crystallinity.Chlorite crystallinity can be applied as a reliable regional, statistical technique complementary with, or instead of, the illite crystallinity method. The illite and chlorite crystallinity scales used here are related to Kübler's epi-, anchi- and diagenetic zones and correlated with coal rank, conodont colour alteration and mineral facies data. As the effects of the detrital white mica can be observed even in the 〈2-μm fractions of anchizonal metapelites, the anchizone boundaries determined solely on the base of ‘fixed’illite crystallinity values may vary with amounts of detrital and newly formed muscovite–illite. Hence a complex approach utilizing more than one method for determination of grade is preferred for petrogenetic purposes, even if relationships between crystallinity scales, coal rank and mineral facies also vary strongly in different tectonic settings and lithologies.

Notes: Abstract Illite crystallinity (IC) and other indicators of the grade of very-low-grade metamorphism associated with the appearance of various stages of slaty cleavage in phyllosilicate-rich rocks have been compiled from a wide variety of terranes. IC values have been converted to a Kübler-equivalent standard scale, but the diverse characterizations of the cleavage fabrics in published descriptions do not always allow an unequivocal identification of equivalent stages of cleavage development.Nevertheless, there exists a distinct relationship between grade and the appearance of various stages of cleavage development.(1) Indications of incipient slaty cleavage, such as S0–S1 pencil structure, appearance of primary (S1) crenulation cleavage and of closely-spaced cleavage without parallel fabric in the microlithons, is associated with a wide range of mostly medium- and high-grade diagenetic IC values.(2) The appearance of smooth cleavage with a strong parallel fabric in the microlithons and/or quartz–mica ‘beards’and the chlorite–mica stacks shortened at a high angle to (001), and of irregular cleavage in sandy beds is associated with a much narrower range of predominantly low- and medium-grade anchimetamorphic grades (rarely high-grade diagenetic). The first appearance of these stages of cleavage development with higher grades can often be related to post-kinematic magmatic heating, polymetamorphism (pre-cleavage metamorphism), or ‘static’recrystallization without cleavage formation, for example in low-strain zones.There exists a relationship between finite strain, fabric and metamorphic grade in mudstones and slates; in coarser clastic rocks the same finite strain–fabric relationship occurs at appreciably higher grades. A relationship between finite strain in carbonate rocks and IC in the nearby rocks has been reported from the Helvetic zone of the Swiss Alps.The earlier stages of cleavage formation are associated with little improvement in IC; the narrow range of IC associated with smooth cleavage is concluded to represent recrystallization and grain growth concurrent with cleavage formation.

Notes: Distinctive lithological associations and geological relationships, and initial geochronological results indicate the presence of an areally extensive region of reworked Archaean basement containing polymetamorphic granulites in the Rauer Group, East Antarctica.Structurally early metapelites from within this reworked region preserve complex and varied metamorphic histories which largely pre-date and bear no relation to a Late Proterozoic metamorphism generally recognized in this part of East Antarctica. In particular, magnesian metapelite rafts from Long Point record extreme peak P–T conditions of 10–12 kbar and 100–1050°C, and an initial decompression to 8 kbar at temperatures of greater than 900°C. Initial garnet–orthopyroxene–sillimanite assemblages contain the most magnesian (and pyrope-rich) garnets (XMg= 0.71) yet found in granulite facies rocks. A high-temperature decompressional P–T history is consistent with reaction textures in which the phase assemblages produced through garnet breakdown vary systematically with the initial garnet XMg composition, reflecting the intersection of different divariant reactions in rocks of varied composition as pressures decreased. This history is thought to relate to Archaean events, whereas a lower-temperature (c. 750–800°C) decompression to 5 kbar reflects Late Proterozoic reworking of these relict assemblages.The major Late Proterozoic (c. 1000 Ma) granulite facies metamorphism is recorded in a suite of younger Fe-rich metapelites and associated paragneisses in which syn- to post-deformational decompression, through 2–4 kbar from maximum recorded P–T conditions of 7–9 kbar and 800–850°C, is constrained by geothermobarometry and reaction textures. This P–T evolution is thought to reflect rapid tectonic collapse of crust previously thickened through collision.

Notes: In the southeastern Reynolds Range, central Australia, a low-P granulite facies metamorphism affected two sedimentary sequences: the Lander Rock Beds and the Reynolds Range Group. In the context of the whole of the Reynolds Range and the adjacent Anmatjira Range, this metamorphism is M3 in a sequence M1–4 that occurred over a period of 250 Ma. In particular, M1 affected the Lander Rock Beds prior to the deposition of the Reynolds Group. M3 has an areally restricted, high-grade area in the southeastern Reynolds Range, affecting both the Reynolds Range Group and the underlying Lander Rock Beds. The effects of M3 are characterized by spinel + quartz-bearing peak metamorphic assemblages in metapelites, which imply peak conditions of ≥750°C and 4.5 ± 1 kbar, and involved isobaric cooling or compression with cooling. It is concluded that one of a series of thermal perturbations caused by thinning of mantle lithosphere contemporaneous with crustal thickening was responsible for M3. In the southeastern Reynolds Range, evidence of both the unconformity between the two rock groups and previous metamorphism/deformation has been completely erased by recrystallization during M3–D3.

Notes: On the basis of fluid inclusion evidence, pervasive influx of deep-seated CO2-rich fluids has been invoked to account for mid- to upper amphibolite facies (M2B) metamorphism on the island of Naxos (Cyclades, Greece). In this paper, mineral devolatilization and melt equilibria are used to constrain the composition of both syn- and post-peak-M2B fluids in the deepest exposed levels of the metamorphic complex. The results indicate that peak-M2B fluids were spatially and compositionally heterogeneous throughout the high-grade core of the complex, whereas post-peak-M2B fluids were generally water-rich. The observed heterogeneities in syn-M2B fluid composition are inconsistent with pervasive CO2-flushing models invoked by previous workers on the basis of fluid inclusion evidence. It is likely that few CO2-rich fluid inclusions on Naxos preserve fluids trapped under peak metamorphic conditions. It is suggested that many of these inclusions have behaved as chemically open systems during the intense deformation that accompanied the uplift of the metamorphic complex. A similar process may explain the occurrence of some CO2-rich fluid inclusions in granulite facies rocks.

Notes: A detailed high-pressure experimental study of two mafic xenoliths, in which coexisting garnet and clinopyroxene (± plagioclase, spinel and olivine) were crystallized over a P–T range of 10–30 kbar and 950–1200°C, has revealed significant differences in temperatures from those estimated for coexisting garnets and clinopyroxenes using the Ellis & Green Fe–Mg exchange thermometer. The results show perfect matching at 30 kbar, 1150–1200°C, but increasing deviation at lower pressure and lower temperature, with the Ellis & Green calibration reaching a ΔT (overestimate) of c. 145°C at 10–12 kbar and 950°C. The grossular content of the garnet increases from c. 21 mol.% at 10 kbar to 26–31 mol.% at 30 kbar. These results confirm other recent experimental studies that show that the pressure correction, and possibly to a lesser extent the correction for grossular content, applied by Ellis & Green, are not appropriate for lower pressure conditions, and give estimated temperatures that are significantly high when applied to granulitic terranes formed at c. 10 kbar. The new reconnaissance results allow a graphical interpolation of a garnet–clinopyroxene geothermometer based on the Fe–Mg exchange reaction which should be applicable to assemblages formed under lower crustal conditions.

Notes: The Main Zone of the Hidaka Metamorphic Belt is an uplifted crustal section of island-arc type. The crust was formed during early Tertiary time, as a result of collision between two arc–trench systems of Cretaceous age. The crustal metamorphic sequence is divided into four metamorphic zones (I–IV), in which zone IV is in the granulite facies.A detailed study of the evolution of the Hidaka Belt, based on a revised P–T–t analysis of the metamorphic rocks, notably a newly found staurolite-bearing granulite, confirms a prograde isobaric heating path, after a supposed event of tectonic thickening of accretionary sedimentary and oceanic crustal rocks. During the peak metamorphic event (c. 53 Ma), the regional geothermal gradient attained 33–40° C km−1, and the highest P–T condition obtained from the lowest part of the granulite unit is 830° C, 7 kbar. In this part, XH2O of Gt–Opx–Cd gneiss is about 0.15 and that of Gt–Cd–Bt gneiss is 0.4. The P–T–XH2O condition of the granulite unit is well within a field where fluid-present partial melting of pelitic and greywacke metamorphic rocks takes place. This is in harmony with the restitic nature of the Gt–Opx–Cd gneiss in the lowest part of the granulite unit.The possibility that partial melting took place in the Main Zone is significant for the genesis of the peraluminous (S-type) granitic rocks within it. The S-type granitic rocks in this zone are Opx–Gt–Bt tonalite in the granulite zone, Gt–Cd–Bt tonalite in the amphibolite zone, and Cd–Bt–Mus tonalite in the Bt–Mus gneiss zone. The mineralogical and chemical nature of these strongly peraluminous tonalitic rocks permit them to be regarded as having been derived from S-type granitic magma generated by crustal anatexis of pelitic metamorphic rocks in deeper crust.

Notes: The Whitestone Anorthosite (WSA), located in southern Ontario, underwent granulite facies metamorphism during the Grenville orogeny at 1.16 Ga. During the waning stages of metamorphism fluids infiltrated the outer portions of the anorthosite and promoted the formation of an envelope comprised of upper amphibolite facies mineral assemblages. Also, this envelope corresponds to portions of the anorthosite that underwent deformation related to movement along a high-grade ductile shear zone. Samples from this portion of the anorthosite (the margin) contain CO2-rich inclusions in plagioclase porphyroclasts (relict igneous phenocrysts), matrix plagioclase and garnet. These inclusions have features which normally are interpreted as indicating that they are texturally primary, but they have relatively low CO2 densities (0.61–0.95 g cm-3). Plagioclase from the anorthosite interior contains texturally secondary inclusions with relatively high CO2 densities (generally from 0.99 to 1.10 g cm-3). The high CO2 densities suggest that the inclusions in the plagioclase of the anorthosite core formed prior to inclusions in porphyroclast minerals of the outer portions of the anorthosite, an interpretation that is apparently inconsistent with inclusion textures. This apparent paradox indicates that most fluid inclusions from the anorthosite margin were formed during, or were modified by, the dynamic recrystallization that affected this portion of the WSA. In either case, late formation or modification, the texturally primary fluid inclusions do not contain pristine samples of the peak metamorphic fluid. Furthermore, because shear-related deformation is apparently associated with entrapment of the lowest fluid densities, some strain localization persisted to relatively low temperatures (e.g. less than approximately 500° C). These results constrain a part of the retrograde P–T path for this portion of the Grenville Orogen to temperatures of approximately 400–500° C at pressures of approximately 1–2 kbar.

Notes: A suite of metapelites, charnockites, calc-silicate rocks, quartzo-feldspathic gneisses and mafic granulites is exposed at Garbham, a part of the Eastern Ghats granulite belt of India. Reaction textures and mineral compositional data have been used to determine the P–T–X evolutionary history of the granulites. In metapelites and charnockites, dehydration melting reactions involving biotite produced quartzofeldspathic segregations during peak metamorphism. However, migration of melt from the site of generation was limited. Subsequent to peak metamorphism at c. 860° C and 8 kbar, the complex evolved through nearly isothermal decompression to 530–650° C and 4–5 kbar. During this phase, coronal garnet grew in the calc-silicates, while garnet in the presence of quartz broke down in charnockite and mafic granulite. Fluid activities during metamorphism were internally buffered in different lithologies in the presence of a melt phase. The P–T path of the granulites at Garbham contrasts sharply with the other parts of the Eastern Ghats granulite belt where the rocks show dominantly near-isobaric cooling subsequent to peak metamorphism.

Notes: Staurolite porphyroblasts, 1.5–8cm in length and 0.3–2cm in width, in the Littleton Schist at Bolton, Connecticut, contain curved quartz inclusion trails which document synkinematic rotations of at least 135°. The orientations of long axes of these staurolite crystals define a weak preferred orientation in a plane approximately parallel to the external foliation. Serial sections of four differently orientated crystals and U-stage measurements of the orientations of their inclusion trails demonstrate that the inflection hinge line and the statistical ‘symmetry axis’ characterizing the foliation within a porphyroblast are unrelated to the orientations of external crenulations and are, in all cases, parallel to the long axis of the porphyroblast. The cumulative rotation reflected in the curvature of the inclusion trails is a maximum in a c-axis section through the initial core of a crystal. The amount of rotation about the c-axis decreases linearly along the length of the crystal away from the nucleation site.The sense and amount of rotation recorded by a porphyroblast is related to its orientation. A tightly constrained transition from clockwise to anticlockwise rotation defines a slip direction that coincides with the preferred orientation of the staurolite c-axes. The total rotation reflected by the inclusion trails increases as a function of the angle between the c-axes of the staurolite crystals and the slip direction.Initially random staurolite porphyroblasts rotated during growth, as a consequence of laminar shear in the surrounding viscous matrix. This interpretation is quantitatively consistent with: the staurolite preferred orientation; its coincidence with the apparent slip direction; the correlation between both the sense and the amount of rotation and the orientation of the long axis of the porphyroblast; and the twisted conical shape of the family of surfaces defined by the inclusion trails.

Notes: Silica-deficient sapphirine-bearing rocks occur as an enclave within granulite facies Proterozoic gneisses and migmatites near Grimstad in the Bamble sector of south-east Norway (Hasleholmen locality). The rocks contain peraluminous sapphirine, orthopyroxene, gedrite, anthophyllite, sillimanite, sapphirine, corundum, cordierite, spinel, quartz and biotite in a variety of assemblages. Feldspar is absent.Fe2+/(Fe2++ Mg) in the analysed minerals varies in the order: spinel 〉 gedrite ≥ anthophyllite ≥ biotite 〉 sapphirine〉orthopyroxene 〉 cordierite.Characteristic pseudomorph textures indicate coexistence of orthopyroxene and sillimanite during early stages of the reaction history. Assemblages containing orthopyroxene-sillimanite-sapphirine-cordierite-corundum developed during a high-pressure phase of metamorphism and are consistent with equilibration pressures of about 9 kbar at temperatures of 750–800°C. Decompression towards medium-pressure granulite facies generated various sapphirine-bearing assemblages. The diagnostic assemblage of this stage is sapphirine-cordierite. Sapphirine occurs in characteristic symplectite textures. The major mineralogical changes can be described by the discontinuous FMAS reaction: orthopyroxene + sillimanite → sapphirine + cordierite + corundum.The disequilibrium textures found in the Hasleholmen rocks are characteristic for reactions which have been in progress but then ceased before they run to completion. Textures such as reaction rims, symplectites, partial replacement, corrosion and dissolution of earlier minerals are characteristic of granulite facies rocks. They indicate that, despite relatively high temperatures (700–800° C), equilibrium domains were small and chemical communication and transport was hampered as a result of dry or H2O-poor conditions.

Notes: The Vredefort dome (2.0 Ga) represents the central uplift of a very large impact structure. This uplift exposed a nearly complete cross-section through the continental crust in the region, which is 25–30 km thick. Two metamorphic events took place at about the same time as the impact. The first event, so-called static metamorphism, is pre-impact and produced lithologies varying from low-grade shale to high-grade hornfels. It resembles contact metamorphism by its lack of schistosity, but is more regional as it extends over a large area and is not associated with large intrusions.The second event, the post-shock metamorphism, is responsible for the recrystallization of the shock features. The investigation of this event has been focused on the degree of alteration of the coesite-stishovite-bearing pseudotachylite veins that formed during the transit of the shock wave. These high-pressure silica polymorphs are only present in the upper part of the stratigraphic sequence; downward they have been converted to fibrous quartz. At the highest grade, the fibrous quartz is in turn replaced by triple-junctioned mosaic quartz. The post-shock metamorphism was generated by the heat of the rock before shock, plus the heat released by the shock wave. The isograds, plotted on a map, can be translated into depth of burial and therefore provide valuable information regarding the geological setting immediately before impact. At the time of impact, the rocks were relatively cool and the static metamorphism had ceased with several tens of millions of years separating the two metamorphic events. The static metamorphism was probably caused by continental crustal extension in a stress-free environment and the lack of deformation is probably due to rapid uplift during the later stages of the impact event.

Notes: The P–T paths for metamorphic complexes from the Precambrian shields and fold belts of different ages may result from advection, i.e. one-cycle convective processes in the lithosphere. This conclusion has been exemplified by the metamorphic evolution of several well-known complexes, for which an advective model can be successfully applied. Numerical simulations of the above processes in terms of Newtonian rheology by using a two-dimensional finite element program have been conducted.Two representative models for intracontinental gravitational ordering initiated presumably by mantle activity are considered: (i) a thermally activated multi-layered rhythmic sequence and (ii) huge rising diapiars causing circulation, in which crustal lithologies underwent high-P metamorphism (above 10–15 kbar) and subsequent ascent toward the Earth's surface.

Notes: The Waterman Metamorphic Complex of the central Mojave Desert was exposed as a consequence of early Miocene detachment-dominated extension. However, it has evidence consistent with a more extensive geological history that involves collision of a crustal fragment(s), tectonic thickening by overthrusting and two periods of extension. The metamorphic complex contains granitoid intrusives and felsic mylonitic gneisses as well as polymetamorphic rocks that include marble, calc-silicate, quartzite. mafic granulite, pyribolite, amphibolite, migmatite and biotite schist. The latter group of rocks was affected by an initial series of high-grade metamorphic events (M1 and M2) and a localized lower grade overprint (M3). The initial metamorphism (M1) can be separated into two stages along its high-grade P–T path: M1a, a granulite facies metamorphism at 800–850° C and 7.5–9 kbar and Mlb, an upper amphibolite facies overprint at 750–800° C and 10–12 kbar. M1a developed mineral assemblages and textures consistent with granulite facies conditions at a reduced activity of H2O and is associated with intense ductile deformation (D1) and minor local partial melting. M1b overprinted the granulite assemblages with a series of hydrous phases under conditions of increasing pressure and H2O activity and is accompanied by little or no deformation. M2 developed at lower pressures and temperatures (650–750° C, 4.5–5.5 kbar) and is distinguished by a second local overprint of hydrous phases that reflects an input of aqueous fluids probably associated with the intrusion of a series of granitic dykes and veins. Effects of M3 are confined to the Mitchel detachment zone, an anastomosing early Miocene detachment fault, and are characterized by local ductile/brittle deformation (D2) of the pre-existing high-grade rocks and granitoid intrusives and by the production of mylonites and mylonitic gneisses under greenschist facies conditions (300–350° C, 3–5 kbar). The initial overprint (M1a) represents metamorphism, devolatilization and minor partial melting of supracrustal rocks under granulite facies conditions as a consequence of tectonic and, possibly, magmatic thickening. The increasing pressure transition of M1a to M1b reflects a period of continued compressional tectonism, thrusting and influx of H2O, in part, locally related to crystallization of partial melts. The near isothermal decompression between M1b and M2 probably represents a pre-112-Ma extensional episode that may have been the result of a decompressional readjustment of a thickened crust. Following the initial extensional event, the metamorphic complex remained at depths of 10–17 km for at least 90 Ma until it was uplifted following Miocene extension. M3 develops locally in response to this second extensional period resulting from the early Miocene detachment faulting.

Notes: The High Himalayan Crystalline Sequence in north-central Nepal is a 15-km-thick pile of metasediments that is bound by the Main Central Thrust to the south and a normal fault to the north. The Langtang section through the metasediments shows an apparent inversion of metamorphic isograds with high-P, kyanite-grade rocks exposed beneath low-P, sillimanite-grade rocks. Textural evidence confirms that the observed inversion is a result of a polyphase metamorphic history and phase equilibria studies indicate that thermal decoupling has occurred within a mechanically coherent section of crust. Rocks now exposed at the base of the High Himalayan thrust sheet underwent Barrovian regional metamorphism (M1) prior to 34 Ma in the early stages of the Himalayan orogeny, recording metamorphic conditions of T= 710 ± 30° C, P= 9 ± 1 kbar. After the activation of the Main Central Thrust, which emplaced these metapelites southwards onto the lower grade Lesser Himalayan formations, the upper part of the thrust sheet was overprinted by a second heating event (M2), resulting in sillimanite-grade metamorphism and anatexis of metapelites at T= 760 ± 30° C, P= 5.8 ± 0.4 kbar between 17 and 20 Ma. Crustally derived, leucogranite magmas have been emplaced into low-grade Tethyan sediments on the hangingwall of the normal fault that bounds the northern limit of the metapelitic sequence.The cause of the selective heating of the upper section of the metasediments during M2 cannot be reconciled with either post-thrusting thermal relaxation or advection models. The cause of M2 remains problematical but it is suggested that heat focusing has occurred at the top of the High Himalayan Crystalline Sequence as a result of movement on the normal fault blanketing metapelites of high heat productivity with low-grade sediments of low thermal conductivity. This model implies that the normal fault was active before M2, consistent with decompression textures that formed during, or shortly after, sillimanite-grade metamorphism.

Notes: The two major Early to Middle Palaeozoic tectonic/metamorphic events in the northern Appalachians were the Taconian (Middle to Late Ordovician) in central to western areas and the Acadian (Late Silurian to early Middle Devonian) in eastern to west-central areas. This paper presents a model for the Acadian orogenic event which separates the Acadian metamorphic realm into eastern and western belts based on distinctively different styles. We propose that the Acadian metamorphism in the east was the delayed consequence of Taconian back-arc lithospheric modification. East of the Taconian island arc, thick accumulations of Late Ordovician and Silurian sediments, coupled with plutons rising along a magmatic arc, produced crustal thermal conditions appropriate for anomalously high-T, low-P metamorphism accompanied by major crustal anatexis. In this zone, upward melt migration was coupled with subsequent E-W crustal shortening (possibly due to outboard collision with the Avalon terrane) to produce mechanical conditions that favoured formation of fold and thrust nappes and resultant tectonic thickening to the west (and probably to the east as well).The basis for the distinction between the Eastern and Western Acadian events lies in the contrasting styles of metamorphism accompanying each. Evidence for contrasting metamorphic styles consists of (1) estimated metamorphic field gradients (MFGs) based on thermobarometric studies, and (2) petrological evidence for contrasting P–T trajectories. West of the Acadian metamorphic front, the Taconian zone has an MFG in which peak temperatures of 400-600° C were reached at pressures of about 4–6 kbar, with both P and T increasing to the east. Near its western edge, the Western Acadian metamorphic overprint has a similar MFG to the Taconian, and is mainly discriminated by 40Ar/39Ar dating and microtextural evidence. East of this narrow zone, the Western Acadian overprint is characterized by progressively higher temperatures (600–725° C) and pressures (6.5–10 kbar, or more) to the east, yielding an overall MFG that lies along, or slightly above, the kyanite–sillimanite boundary on a P–T diagram. There is little or no plutonism accompanying Western Acadian metamorphism.In contrast, thermobarometry in the Eastern Acadian, east of the Bronson Hill Belt, yields high-T, intermediate-P conditions for the highest grade rocks known in New England: T= 650–750° C, P= 4.5–6.5 kbar for granulite facies assemblages which apparently formed along an ‘anticlockwise’P–T path. The Bronson Hill Belt lies geographically between the Eastern and Western Acadian zones and shows transitional petrological behaviour: anomalously high temperatures at intermediate pressures, but a ‘clockwise’ path with decompression cooling.Radiometric dating indicates peak Taconian conditions may have been achieved as early as 475 Ma in the Taconian hinterland and as late as 445 Ma in the Taconian foreland (including the Taconic allochthons). Eastern Acadian magmatism may have started as early as 425 Ma, and most nappe-stage deformation and metamorphism in the Eastern Acadian zone appears to have ended by about 410 Ma. Tectonic thickening in the Western Acadian (including the western counterparts of the nappe-stage deformation documented in the Eastern Acadian) must pre-date attainment of peak metamorphic conditions dated at 395–385 Ma. Dome-stage deformation clearly post-dates peak metamorphism and deforms metamorphic isograds. The end of Western Acadian deformation is well constrained by 370-375 Ma radiometric ages of late pegmatites and granitoids which cross-cut all structures.

Notes: A suite of migmatites in uppermost amphibolite facies schists of the Koettlitz Group exposed in the Taylor Valley, Antarctica, provides direct evidence of the behaviour of partially molten rock during syn-anatectic deformation. The geometry of the migmatites is directly related to their position relative to the hinge of a kilometre-scale antiform. Migmatitic rocks on the fold limbs are characterized by extensional shears and fractures, filled with leucosome material, that intersect the pervasive foliation and millimetre-thick stromatic leucosomes. Vein- and dyke-like leucosomes become more common and thicker from the limb to the hinge region of the antiform. Rocks characterized by high leucosome-to-rock ratios near the antiform hinge are xenolithic in appearance. Major parasitic folds within the hinge contain leucogranite ‘microplutons’ up to 50 m across beneath refractory ‘cap-rock’ layers.Angular boudinage structures in schists surrounded by leucosomes indicate a relatively low yield strength in the leucosome, which is compatible with a molten rather than solid leucosome. Leucogranite-bearing extensional shears and fractures indicate that repeated extensional fracturing and shearing promoted by high fluid (melt) pressure is an important mechanism of melt segregation. Dilation in the hinges of developing folds aids the migration of melt into fold hinges and the development of 10–50-m-wide ‘microplutons’ of xenolith-rich leucogranite.Lack of vapour-absent melting and consequent low melt-to-rock ratios allowed the Koettlitz Group to maintain its structural coherency on a kilometre scale. Consequently, leucosome ‘microplutons’ did not exceed 50 m in width, and therefore observed leucosomes have not contributed to the development of adjacent plutonic-scale granitoids.

Notes: Systematic mapping of a transect along the well-exposed shores of Georgian Bay, Ontario, combined with the preliminary results of structural analysis, geochronology and metamorphic petrology, places some constraints on the geological setting of high-grade metamorphism in this part of the Central Gneiss Belt. Correlations within and between map units (gneiss associations) have allowed us to recognize five tectonic units that differ in various aspects of their lithology, metamorphic and plutonic history, and structural style. The lowest unit, which forms the footwall to a regional decollement, locally preserves relic pre-Grenvillian granulite facies assemblages reworked under amphibolite facies conditions during the Grenvillian orogeny. Tectonic units above the decollement apparently lack the early granulite facies metamorphism; out-of-sequence thrusting in the south produced a duplex-like structure. Two distinct stages of Grenvillian metamorphism are apparent. The earlier stage (c. 1160–1120 Ma) produced granulite facies assemblages in the Parry Sound domain and upper amphibolite facies assemblages in the Parry Island thrust sheet. The later stage (c. 1040–1020 Ma) involved widespread, dominantly upper amphibolite facies metamorphism within and beneath the duplex. Deformation and metamorphism recently reported from south and east of the Parry Sound domain at c. 1100–1040 Ma have not yet been documented along the Georgian Bay transect. The data suggest that early convergence was followed by a period of crustal thickening in the orogenic core south-east of the transect area, with further advance to the north-west during and after the waning stages of this deformation.

Notes: The Main Zone of the Hidaka metamorphic belt is an imbricate stack of crustal material derived from an island arc in which a sequence of units with increasing metamorphic grade from low to high structural levels is exposed. The basal part of the metamorphic sequence underwent granulite facies metamorphism with peak P–T conditions of 7kbar, 870°C. In this zone pelitic granulite includes leucosomes which consist mainly of orthopyroxene-plagioclase-quartz.To test whether the leucosome was derived by partial melting of the surrounding pelite, melting experiments of the pelitic granulite were carried out for water-saturated and dry systems at 7 kbar and 850°C. The chemical composition of the leucosome produced during these runs shows a peraluminous S-type tonalitic affinity and is located very close to the tie-line between the average melts produced in water-saturated systems and the average composition of the residual orthopyroxene + plagioclase. This therefore suggests that the lecosome in pelitic granulite was formed by incipient anatexis at close to the highest P–T condition of the Main Zone.The age of the crustal anatexis is determined by the Rb-Sr whole rock isochron method for garnet-cordierite-biotite gneiss (host rock), garnet-orthopyroxene-cordierite gneiss (restite) and S-type tonalite (melt). This gives an age of 56.0 Ma with an initial 87Sr/86Sr ratio of 0.705711. The S-type tonalite magmas that form large intrusive masses in the Main Zone were probably generated by crustal anatexis in deeper parts of the crust at the same time (late Palaeocene).

Notes: Caledonian eclogite facies shear zones developed from Grenvillian garnet granulite facies anorthosites and gabbros in the Bergen Arcs of western Norway allow direct investigation of the relations between macroscopic structures and crystallographic preferred orientation (CPO) in lower continental crust. Field relations on the island of Holsnøy show that the eclogites formed locally from granulite facies rocks by progressive development of: (1) eclogite adjacent to fractures; (2) eclogite in discrete shear zones (〉 2 m thick); (3) eclogite breccia consisting of 〉80% well-foliated eclogite that wraps around rotated granulite blocks; and (4) anastomosing, subparallel, eclogite facies shear zones 30–100 m thick continuous over distances 〉 1 km within the granulite terrane. These shear zones deformed under eclogite facies conditions at an estimated temperature of 670 ± 50°C and a minimum pressure of 1460 MPa, which corresponds to depths of 〉55 km in the continental crust. Detailed investigation of the major shear zones shows the development of a strong foliation defined by the shape preferred orientation of omphacite and by alternating segregations of omphacite/garnet-rich and kyanite/zoisite-rich layers. A consistent lineation throughout the shear zones is defined by elongate aggregates of garnet and omphacite. The CPO of omphacite, determined from five-axis universal stage measurements, shows a strong b-axis maximum normal to foliation, and a c-axis girdle within the foliation plane with weak maxima parallel to the lineation direction. These patterns are consistent with deformation of omphacite by slip parallel to [001] and suggest glide along (010). The lineation and CPO data reveal a consistent sense of shear zone movement, although the displacement was small. Localized faulting of high-grade rocks accompanied by fluid infiltration can be an important mode of failure in the lower continental crust. Field relations show that granulite facies rocks can exist in a metastable state under eclogite facies conditions and imply that the lower crust can host differing metamorphic facies at the same depth. Deformation of granulite and partial conversion to eclogite, such as is exposed on Holsnøy Island, may be an orogenic-scale process in the lowermost crust of collisional orogens.