ISSN:
0933-5137
Keywords:
Chemistry
;
Polymer and Materials Science
Source:
Wiley InterScience Backfile Collection 1832-2000
Topics:
Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics
Description / Table of Contents:
The influence of Si and P contents in steels on the galvanizing behaviorThe galvanizing behavior of 40 structural steels in current use was investigated in relation to the complex influence of the Si/P content under conditions that are usual in the hot dip galvanizing industry (440/450/460 °C,5/10/15 min immersion time). The effect of P on the increase of coating thickness on steels with 0,01 to 0,40 % Si begins to be perceptible at 〉 0,020 % P. The influence of P increases with decreasing Si content of the steels and decreasing temperature of the melt. In steels with ≤ 0,12 % Si, an increased P content causes a shift of the thickness maxima in the temperature range from 440 to 450 °C, such as is otherwise typical of steels of 0,12 % to 0,28 % Si with 〈 0,020 % P. Zinc coatings on steels with the critical P/Si content (0 to 0,20 % Si/〉 0,020 % P) as a rule are more unstable. With increased immersion time at the temperature stated above, floating away of the ξ phase into the zinc melt may occur. This could also be observed with Sandelin steels in the most critical Si range (0,07 to 0,10 %) with 〈 0,020 % P, with an immersion time of 15 min. It is possible to reduce the thickness of zinc coatings by adding small amounts of Al to the zinc melt (〈 0,03 %).This effect of Al at a concentration that is below what is required for the known inhibitory action by the formation of an thin Fe2Al5-or Al-containing δ1 film on the steel surface is attributed to the instability of the ξ phase, a proportion of which floats away into the zinc melt.
Notes:
Es wurde das Verzinkungsverhalten von 40 aktuellen Baustählen in Abhängigkeit vom komplexen Einfluß des Si-/P-Gehaltes bei den in der Feuerverzinkungsindustrie üblichen Bedingungen (440/450/460 °C, 5/10/15 min Tauchdauer) untersucht. Eine spürbare Wirkung von P auf das Schichtdickenwachstum von Stählen mit 0,01 bis 0,40 % Si beginnt bei 〉 0,020 % P. Der Einfluß von P ist um so größer je kleiner der Si-Gehalt der Stählen und je niedriger die Temperatur der Schmelze ist. Bei Stählen mit ≤ 0,12 % Si verschiebt ein erhöhter P-Gehalt die Schichtdickenmaxima in dem Temperaturbereich von 440 bis 450 °C, wie das sonst für Stähle 〉 0,12 % bis 0,28 % Si mit 〈 0,020 % P typisch ist. Zinküberzüge von Stählen mit kritischem P-/Si-Gehalt (0 bis 0,20 % Si/〉 0,020 % P) sind in der Regel instabiler. Bei erhöhter Tauchdauer und o. g. Temperatur kann es zu einem Abschwimmen der ξ-Phase in die Zinkschmelze kommen. Auch bei Sandelin-Stählen im kritischsten Si-Bereich (0,07 bis 0,10 %) mit 〈 0,020 % P konnte das bei 15 min Tauchdauer festgestellt werden. Es ist möglich, die Schichtdicke der Zinküberzüge durch Zulegieren kleiner Al-Gehalte zur Zinkschmelze (〈 0,03 %) zu reduzieren. Die Ursache dieses Effektes von Al unterhalb der Konzentration, die für die bekannte Hemmwirkung durch Ausbildung einer dünnen Fe2Al5 -bzw. Al-haltigen δ11-Schicht auf der Stahloberfläche erforderlich ist, wird auf die Instabilität der ξ-Phase, die anteilig in die Zinkschmelze abschwimmt, Zurückgeführt.
Additional Material:
12 Ill.
Type of Medium:
Electronic Resource
URL:
http://dx.doi.org/10.1002/mawe.19970281209
Permalink