ALBERT

Beschreibung: A hybrid jet-pump CO 2 compression system that may enhance system COP and reduce the environmental impact of transport refrigeration is analysed. At an evaporator temperature of –15°C, an ambient temperature of 35°C and a generator temperature of 120°C, COP increases from 1.0 to 2.27 as subcooling increases from 0 to 20 K. Compressor work is reduced by 24% at 20 K subcooling. The optimum degree of subcooling was ~10 K for the operating conditions examined. COP is improved while the size of heat exchangers required to operate the jet pump are minimised with respect to the overall weight of the system.

Beschreibung: Libya has a growing demand for electricity and presently generates almost all of its electrical energy using fossil-fuelled generation plant. An opportunity exists to use the naturally high solar radiation resource that occurs in the south of the country to meet this demand with a renewable energy source. This paper describes the design of a 50 MW photovoltaic (PV) power plant which has been modelled on the conditions pertaining to Al-Kufra. The general energy situation within Libya is described, along with the solar conditions at the proposed location of the power plant. An HIT type PV module has been selected and modelled. The effectiveness of the use of a cooling jacket on the modules has been evaluated. The results show an average increase in efficiency of 0.6%; however, this is not considered to be a justifiable expense. The optimum tilt angle and array layout have been evaluated for the proposed site. The projected energy output has been determined to be 114 GWh per annum with a payback time of 2.7 years and a reduction of CO 2 pollution by 76 thousand tonnes per year. It is recommended that very large-scale PV plants of this type are installed within Libya for the sake of benign environmental impact and diversification of the electrical generation mix.

Beschreibung: In this paper, a thorough review of the available literature on photovoltaic/thermal (PV/T) systems is presented. The review is performed in a thematic way in order to allow an easier comparison, discussion and evaluation of the findings obtained by researchers, especially on parameters affecting the electrical and thermal performance of PV/T systems. The review covers a comprehensive historic overview of PV/T technology, detailed description of conventional flat-plate and concentrating PV/T systems, analysis of PV/T systems using water or air as the working fluid, analytical and numerical models, simulation and experimental studies, thermodynamic assessment of PV and PV/T systems and qualitative evaluation of thermal and electrical outputs. Furthermore, parameters affecting the performance of PV/T systems such as glazed versus unglazed PV/T collectors, optimum mass flow rate, packing factor, configuration design types and absorber plate parameters including tube spacing, tube diameter and fin thickness are extensively analyzed. Based on the thorough review, it can be easily said that the PV/T systems are very promising devices and PV/T technology is expected to become strongly competitive with the conventional power generation in the near future.

Beschreibung: In this study, an experimental research concerning the effects of passive cooling on performance parameters of silicon solar cells was presented. An aluminum heat sink was used in order to dissipate waste heat from a photovoltaic (PV) cell. Dimensions of the heat sink were determined considering the results of a steady-state heat transfer analysis. The experiments were carried out for different ambient temperatures and various illumination intensities up to 1 sun under solar simulator. Experimental results indicate that energy, exergy and power conversion efficiency of the PV cell considerably increase with the proposed cooling technique. An increase of ~20% in power output of the PV cell is achieved at 800 W/m 2 radiation condition. Maximum level of cooling is observed for the intensity level of 600 W/m 2 . Performance of PV cells both with and without fins increases with decreasing ambient temperature.

Beschreibung: High-temperature thermal storage (HTTS) in soils is a promising energy-saving technology for space heating of buildings. Based on a laboratory experimental setup using a vertical borehole heat exchanger (BHE), dynamic changes of the soil temperature and moisture content during the thermal storage process are studied. Effects of the heat injection temperature and initial moisture content on the thermal performance of the BHE are analyzed. The results show that at the first thermal storage stage, the soil temperature and moisture content near the heat source may appear a temporary peak. Its occurrence depends on the initial soil moisture content, the heat injection temperature and the distance from the heat source. As the heat injection temperature increases, the heat transfer rate of the BHE increases greatly. As the initial soil moisture content increases, the temperature profile near the BHE tends to be deviated from the results predicted by heat conduction, thereby influencing the thermal performance of the BHE. The present results can provide useful guidelines for the design of an HTTS system.

Beschreibung: The thermal performance of a horizontal-coupled ground-source heat pump system has been assessed both experimentally and numerically in a UK climate. A numerical simulation of thermal behaviour of the horizontal-coupled heat exchanger for combinations of different ambient air temperatures, wind speeds, refrigerant temperature and soil thermal properties was studied using a validated 2D transient model. The specific heat extraction by the heat exchanger increased with ambient temperature and soil thermal conductivity, however it decreased with increasing refrigerant temperature. The effect of wind speed was negligible.

Beschreibung: CO 2 solid–gas two-phase flow is investigated in an ultra-low temperature cascade refrigeration system. Visualization test shows that dry ice sedimentation occurs in low mass flow rate. The sedimentation also occurs at low condensation temperature and low heating power input. On the basis of the present investigation, it is found that the present ultra-low temperature cascade refrigeration system works better at a heating power input above 900 W and condensation temperature above –20°C. Under suitable operating conditions, the present ultra-low temperature cascade refrigeration system has shown the capability of achieving an ultra-low temperature of –62°C continuously and stably.

Beschreibung: Nowadays, many working environments are located within facilities that are not visually connected with the exterior. This is due to the new architectural paradigms as regards the design, based on the possibility to substitute natural light for artificial lighting even in daytime. Accordingly, the need of reducing energy costs and the user's wish to optimize lighting and visual comfort levels raises the option of innovative natural lighting systems implementation. For a luminous retrofitting case, located in Mendoza, Argentina, a specific methodology used determined that the more adequate natural lighting strategy would be redirecting direct sunlight, working on the reflected light design. The methodology proposed is formed by an analysis of the initial situation, conditions modelization and design resolving proposals, through luminous evaluation, real and virtual scale model construction, and performance evaluation using heliodon and simulation software. This work points to use natural lighting to reduce energy consumption and get better luminous ambient through the application of a low-cost daylighting system. In the mentioned case, strategies of redirection of the solar component capable of optimizing indoor lighting levels up to a 40% were applied.

Beschreibung: This paper aimed to numerically investigate the performance comparison between counterflow and crossflow heat exchangers for indirect evaporative air cooler. Simulation results indicate that cooling performance difference between the two configurations considerably depends on the configuration structure of heat exchangers, the inlet air status and the mass flow rates of primary and secondary. Among types of the cross-sectional shape considered in this paper, the counter configuration with rectangle channels which has a length-to-width ratio of 16:1 can provide the best cooling performance. The wet bulb effectiveness of counterflow configuration is about 7% greater than that of crossflow configuration with increasing inlet air temperature on average. The higher the inlet air temperature, the bigger the EER, cooling capacity and supply air temperature difference between the two configurations. With increasing relative humidity, the two configurations keep an average wet bulb effectiveness difference of 7.1%. The wet bulb effectiveness difference between the two configurations narrows down from 8.3 to 5.3% with increasing air velocity.

Beschreibung: Housing associations (HAs) are responsible for building and managing approximately one-third of affordable homes in Scotland. The adoption of low carbon technologies (LCTs) by HAs presents an area that could potentially help towards reducing the carbon footprint of affordable housing and the fuel poverty of tenants. This research thus explores the issues pertaining to the adoption of LCTs from the perspective of two Scottish HAs. Semi-structured interviews were conducted with selected members of the management team in both HAs. The empirical findings revealed that HA-related issues (such as organization culture, being a learning organization and training) and tenant-related issues (such as social cohesion, change in behaviour and training) can both impinge on the adoption of LCTs in HAs. It is contended that there is a piecemeal adoption of LCTs and if mass adoption is to be realized, this will require a nationwide programme that is aimed at supporting the adoption of LCT, in addition to building the skills capacity of the construction industry which is seemingly ill-prepared.

Beschreibung: Focusing on the ‘worst-case scenario', a modelling study was carried out to examine whether a low cost ventilation solution could provide basic comfort in a specific atrium-building design. This study combined dynamic thermal modelling (DTM) and computational fluid dynamics (CFD) in investigating how thermal conditions, namely the air movement and temperature distribution within an atrium responded to the side-lit form and other changes of design variables such as inlet to outlet opening area ratios and also the outlet's arrangement. The predicted temperature distribution, airflow patterns and comfort indices would provide a better understanding how the design variables affect thermal condition and comfort within the atrium, particularly at the occupied areas under a low cost ventilation solution—pressurized ventilation. The simulation results revealed that sufficiently higher inlet to outlet opening area ratio (i.e. n 〉 1) could improve the thermal condition on the open corridors, the occupied areas, even on high levels; while with an equal inlet to outlet opening area ratio (i.e. n = 1), changing the outlet's arrangement (i.e. location and configuration) did not significantly affect thermal condition. The practical aspect of this study is 2-fold. First, the low cost ventilation solution using exhaust air from surrounding fully air-conditioned rooms could provide acceptable thermal comfort at the open corridors/walkways surrounding the atrium. Secondly, combining a DTM and CFD can be an effective tool to test various design options to achieve an optimal solution. The parametric presented here could be used in similar studies aiming at optimize environmental engineering solutions that balance comfort and cost.

Beschreibung: Most existing nuclear power plants in North America are typically water-cooled and operate at 250–500°C. For this temperature level, the copper–chlorine (Cu–Cl) cycle is one of the most promising cycles that can be integrated with nuclear reactors for hydrogen production by decomposing water into its constituents. In this study, we analyze the heat exchangers in the Cu–Cl thermochemical cycle so as to enhance heat transfer effectiveness and thereby improve the cycle efficiency. The thermal management options for internal and external heat transfer are studied and heat recovery opportunities are investigated and compared. Each heat exchanger in the cycle is examined individually based on the chemical/physical behavior of the process, and the most appropriate options are recommended. A thermodynamic analysis and associated parametric studies are performed for various configurations to contrast their efficiencies and effectivenesses.

Beschreibung: The flaring of oil-associated gas continues to generate insidious environmental and energy consequences against efforts toward sustainable development for Nigeria. This study compared some of the economic benefits lost due to flared gas at flow stations with fuelwood energy consumption. The objectives were to assess comparative cost suffered by host communities, estimate greenhouse gases emissions of burnt-off gas and evaluate possible effects of post-global financial meltdown support policies on climate change. Parameters for evaluating the environmental and energy impacts were measured directly or collected from flow stations through opinion surveys and meetings. An inventory of the motors, voltages and power ratings of the machines used at the flow stations was made, with a view to quantifying the energy involved in drilling operations. For estimation of health risks and gaseous emissions, SIMPACTS method was used. Results from the study show that an annual average of 2040 MJ of fuelwood is consumed in Nigeria, 77.3% of the sourcing is done by children and the time spent in fuelwood trips is between 4 and 5 h, at a frequency of three to four times a week. This amount of fuelwood consumed examined alongside 2.5billion standard cubic feet of gas flared per day, revealed the quantity of energy that ought to be saved and related avoidable extreme weather conditions that prevail in Nigeria. Therefore, gas flaring violates the tenets of sustainable development and seriously contributes to global warming. In conclusion, flare down can be achieved by utilizing micro-gas turbines, re-injection and pursued as part of a new agenda for responsible governance in Nigeria.

Beschreibung: In order to investigate the operation performance of ground-coupled heat-pump (GCHP) system, an analytical simulation model of GCHP system on short time-step basis and a computer program based on this model to predict system operating parameters are developed in this study. Besides, detailed on-site experiments on GCHP test rig installed in a temperate region of China are carried out. The temperature distributions of borehole as well as ground around borehole at different depths are evaluated. Operation parameters of GCHP system such as circulating water temperature, heat rejection into ground and system power consumption when the system operated in intermittent and continuous modes are investigated. The accuracy of proposed simulation model is validated by experimental data. The advantage of GCHP technology in energy efficiency over other conventional air-conditioning systems is proved to be obvious and the performance of GCHP system is found to be affected by its operation modes.

Beschreibung: Sorption heat pumps based on monovariant reactions, such as ammonia-salt systems, can operate at low driving temperatures and achieve high power densities in comparison with multi-variant sorption systems. The disadvantage of monovariant systems, however, is the inflexibility towards required temperature levels. Where multivariant systems scale over a large range of temperatures, for the monovariant system, the temperature range is limited by the discrete transition from (fully) adsorbed to desorbed state. To increase flexibility towards changes in operating temperatures of the monovariant sorption systems, the extension of such systems with a compressor has been studied. Focus of this research is on the use of ammonia salts for type II heat pump for upgrading low temperature industrial waste heat to low–medium pressure steam. At ECN, a system based on LiCl–MgCl 2 ammonia reactions has proved to achieve sufficient temperature lift (〉50°C) and cyclic stability (〉100 cycles) but requires a minimum temperature of 120°C for proper operation. To add flexibility to this system, i.e. to be able to use waste heat below 120°C, the performance of a hybrid variant containing both thermally driven sorption reactors and a compressor has been evaluated. This evaluation focuses on extension in temperature range, and exergy efficiency and economic consequences of such a hybrid system. In addition, the possibility to use other ammonia-salt combinations has been investigated. The conclusions are that hybrid systems can reduce primary energy consumption and be economically feasible. It also shows that salt combinations other than LiCl–MgCl 2 could be more suitable for a hybrid thermo-chemical adsorption–compression system.

Beschreibung: The production of biofuels and other products from algae is a technology that is rapidly developing. This paper presents an overview of algae, its benefits over other biofuel sources and the technology involved in producing algal biofuel. The case study in this report looks at the potential of algal biodiesel, produced using power plant exhaust, to replace our current petrodiesel supply and consequently reduce greenhouse gas emissions. The results suggest that using 60% of all coal and gas power plants would allow this new fuel source to replace petrodiesel entirely and thus reduce greenhouse gas emissions by ~5%. The challenge at the present is to improve the efficiency of algal fuel production technology so as to lower the cost of algal biodiesel and thereby make it commercially competitive with petrodiesel. Researchers are currently developing various means of accomplishing this and successful commercialization is anticipated by 2018.

Beschreibung: Performance testing of solar heating systems and solar collectors according to International Standard Test procedures require sophisticated and expensive elaborate set-ups. Outdoor collector testing is not feasible in countries with widely fluctuating solar radiation conditions. Indoor testing does not give its true performance when the equipment is situated outdoors. This paper reports on a simple test procedure where the performances of the flat plate, U-tube and heat pipe natural convection solar heaters and the heat pipe force convection solar heater, which were tested on different days, were compared as if they were simultaneously tested side by side. The procedure allowed: (i) the maximum hot water storage temperature that could be achieved by the system over a long period of time without any water draw-off at all, (ii) overnight water temperature drop in the storage tank and (iii) expected end-of-day water temperature and mean system efficiency when water is completely drained down (draw-off) in the evening. Maximum temperatures reached for the natural convection heat pipe, force convection heat pipe, flat plate and U-tube system were 100, 84, 65 and 50°C, respectively. Overnight temperature drops due to standing tank loss and reverse flow were presented and found to be dependent upon initial tank temperature. By pro-rating all the results to reflect on the same area/volume ratio, the expected water temperature rise for the U-tube, forced convection heat pipe, flat plate and natural convection heat pipe systems was 13.6, 17.6, 20.6 and 28.4°C, respectively.

Beschreibung: New definitions of two-phase viscosity, based on its analogy with thermal conductivity of porous media, are investigated for transcritical capillary tube flow, with CO 2 as the refrigerant. Friction factor and pressure gradient quantifies are computed based on the proposed two-phase viscosity model using homogeneous modelling approach. The Proposed new models are assessed based on test results in the form of temperature profile and mass flow rate in a chosen capillary tube. It is shown that all the proposed models of two-phase viscosity models show a good agreement with the existing models such as McAdams et al ., Cicchitti et al ., etc. The influence of the viscosity model is found to be insignificant unlike to other conventional refrigerants in capillary tube flow.

Beschreibung: The ammonia–water absorption cycle could transfer thermal energy into chemical energy by the change in solution concentration, which low-grade heat released by industry-concentrated areas could be utilized to provide heating or cooling in the user site over long distance. No heat insulation is required for the transportation pipelines and the energy consumption is reduced greatly. The simulation researches show that thermal coefficient of performance (COP) is at 0.5 and exergy efficiency is 〉0.2 when generation temperature is at 110°C to provide cooling in summer; thermal COP is at 0.6 and exergy efficiency is 〉0.3 to provide heating in winter. Electrical COP as high as 50 could be realized if the transportation distance is 〉50 km. Therefore, the COP of the system is determined by thermal COP (nearly equal). An experimental prototype has been built to testify this theory. Thermal COP is 0.43 when chilled water at 8°C is obtained in summer. In winter, thermal COP is 0.45 when hot water at 58°C is obtained. The deviations between experimental and simulation results are ~20%. The economic assessment based on the reasonable assumptions shows that the investment cost of the transportation pipelines of a 500 MW, 50 km system could be recovered within 15 months, in which the whole system costs could be recovered within 4 years.

Beschreibung: In process industry, large amounts of surplus heat are available. Electricity production is an interesting method to recover this energy. This paper focuses on the off-design operation of the Rankine cycles and compares the behaviour of transcritical CO 2 cycles and an organic Rankine cycle (ORC) with R-123 as the working fluid. The simulations show that the ORC is more sensitive than the CO 2 cycle to reduction in available heat, and will with only small changes get droplets in the inlet of the expander. With small increments in the available heat source, the CO 2 cycle also seem to have a marginally better response without control of the process.

Beschreibung: The advantages of numerical modelling compared with experimental studies (e.g. reduced cost, easy control of the variables, high yield etc.) are well known. Theoretical studies where experimental validation is also presented provide an important added value to numerical investigations. In the present paper, experimental and computational fluid dynamics (CFD) results for a 5-kW-rated capacity steam ejector, with a variable primary nozzle geometry, are presented and compared. The variable geometry was achieved by applying a movable spindle at the primary nozzle inlet. Relatively low operating temperatures and pressures were considered, so that the cooling system could be operated with thermal energy supplied by solar collectors (solar air-conditioning). The CFD model was based on the axi-symmetric representation of the experimental ejector, using water as a working fluid. The experimental entrainment ratio varied in the range of 0.1–0.5, depending on operating conditions and spindle tip position. It was found that the primary flow rate can be successfully adjusted by the spindle. CFD and experimental primary flow rates agreed well, with an average relative error of 8%. CFD predicted the secondary flow rate and entrainment ratio with good accuracy only in 70% of the cases.

Beschreibung: Biodiesel, an alternative fuel of petroleum diesel, is mainly used to reduce the environmental impact of emissions without modifying engines. This study compares the performance and emissions characteristics of different biodiesel blends with petroleum diesel using an internal combustion engine (Kubota V3300) and following ISO 8178 standards. Two types of biodiesel, type A (80% tallow and 20% canola oil methyl ester) and type B (70% chicken tallow and 30% waste cooking oil methyl ester), were tested in this study. It was found that the performance (mainly torque and brake power) of both biodiesel fuels reduces with increasing blend ratio which can be attributed to lower energy content of biodiesel. Specific fuel consumption increases for both biodiesels compared with diesel fuel, as expected. Some of the greenhouse gas emissions were found to be higher than petroleum diesel, whereas some were lower. Overall, Biodiesel A was found to produce lower emissions across the board compared with diesel and Biodiesel B.

Beschreibung: In this work, a micro-tri-generation system integrated with a solar system is studied. A basic micro-cogeneration technology [micro-CHP (combined heat and power) system] integrating solar collectors, storage tank, micro-turbine and a thermodynamic cycle based on the organic Rankine cycle (ORC) is combined with an absorption chiller. The heat rejected at the condenser of the micro-CHP system is used for water heating (WH), and the absorption chiller is used for space cooling. Hot water from the solar storage tank is the heat source for the cooling system (absorption chiller) and the micro-CHP system. A heat exchanger is used to transfer heat from the hot water circuit to the power cycle (which uses an organic refrigerant). The micro-CHP system under analysis uses a micro-turbine and an electric generator with a power output of 5 kW. The turbine inlet temperature is 80°C and the working fluid is cyclohexane. The absorption chiller, which is a single-effect water-fired chiller, operates with a lithium bromide and water mixture, and water inlet temperature is between 80 and 100°C. The performance for different solar collector areas and tank capacities was evaluated through a numerical model. A hotel building was used as a case study and the analysis was extended throughout the cooling season, for climatic conditions of different European cities: Athens (Greece), Lisbon (Portugal), Madrid (Spain), Paris (France) and London (UK). The monthly average solar fraction was evaluated for different cases: the micro-CHP system, the cooling system and the micro-tri-generation system with the useful condenser energy used for WH. The solar fraction of the micro-CHP system was low, compared with that of the cooling system, because the efficiency of the micro-CHP system is lower than 7%. However, when the tri-generation system is considered, the monthly average solar fraction is much higher, due to the utilization of the condenser heat. The solar system, cooling system and its components were modelled with the TRNSYS simulation program. The micro-CHP system was modelled with EES software.

Beschreibung: Concentrating photovoltaic (PV) systems provide an effective way to reduce the cost of electricity production by reducing the amount of silicon required. The use of a Fresnel lens is one of the typical design options for the concentrating PV systems. Compared with a parabolic mirror, a Fresnel lens has its focus behind the lens surface. This gives a convenience for installation of PV cells and also there is no matter of shading caused by the PV cells. However, both Fresnel lens and parabolic dish concentrating PV systems need to be accompanied by a high accuracy sun-tracking system. This study presents the design analysis of a Fresnel lens concentrating PV cell which consists of a small linear Fresnel lens and a strip PV cell. A number of cells may form a modular large concentrating PV system using a single sun-tracking system. Based on the analysis of the ray path through the Fresnel lens and a current density distribution model for the PV cell, a computer program has been produced to predict the irradiance distribution on the PV cell and the distribution of current density. The results are used to determine the effect of sun-tracking deviation and PV cell position on the PV current distribution. The calculated and experimental short-circuit current and open-circuit voltage of the designed Fresnel lens concentrating PV cell are also given.

Beschreibung: In this paper, we investigate using a refrigeration scroll compressor as expander for power generation applications with a Rankine cycle. The methodology employed here has three steps: In the first step, a scroll compressor is selected from a refrigeration manufacturer catalog. Based on catalog data and our simplified model, the specific parameters of the compressor such as the built-in volume ratio and leakage coefficient are determined through mathematical regression. In the second step, the parameters and the efficiency of the Rankine cycle are determined, which use the selected scroll machine in reverse, namely as expander, without any geometrical modifications. The range of temperatures and pressures are kept the same as that characterizing the compressor operation. A simplified expander model is used to predict the efficiency of the prime mover and of the Rankine cycle. A range of working fluids are considered and compared. The expander does not operate optimally when converted from a compressor without any modifications. In the third phase, the geometry of the expander is modified with respect to the rolling angle only in order to obtain the appropriate built-in volume ratio which assures better efficiency of the Rankine heat engine. This paper also presents a parametric study in terms of geometry, working fluid and operating conditions.

Beschreibung: This paper presents the methodology, results and a discussion of thermal response tests (TRTs) performed on a multiple borehole ground heat exchanger. The ground heat exchanger consisted of nine 80-m deep boreholes. TRTs with durations between 48 and 260 h were performed on individual boreholes. Tests were analysed using common evaluation methods, and ground conductivity and borehole resistance values were determined for all nine boreholes. In addition to these parameters, the undisturbed ground temperatures were also determined for individual boreholes using multiple approaches. A sensitivity analysis was performed to analyse the effects of various test and parameter uncertainties on the ground thermal conductivity and borehole thermal resistance estimations.