ALBERT

Description: The knowledge of vegetation dielectric behavior is important in studying the scattering properties of the vegetation canopy and radar backscatter modelling. Until now, a limited number of studies have been published on the dielectric properties in the boreal forest context. This paper presents the results of the dielectric constant as a function of depth in the trunks of two common boreal forest species: black spruce and trembling aspen, obtained from field measurements. The microwave penetration depth for the two species is estimated at C, L, and P bands and used to derive the equivalent dielectric constant for the trunk as a whole. The backscatter modelling is carried out in the case of black spruce and the results are compared with the JPL AIRSAR data. The sensitivity of the backscatter coefficient to the dielectric constant is also examined.

Description: At the Space Photovoltaics Research and Technology (SPRAT) conference at NASA Lewis Research Center, a workshop session was held to discuss issues involved in using photovoltaic arrays ('solar cells') to convert laser power into electrical power for use as receiving elements for beamed power.

Description: Because changes in the Earth's environment have become major global issues, continuous, longterm scientific information is required to assess global problems such as deforestation, desertification, greenhouse effects and climate variations. Global change studies require understanding of interactions of complex processes regulating the Earth system. Space-based Earth observation is an essential element in global change research for documenting changes in Earth environment. It provides synoptic data for conceptual predictive modeling of future environmental change. This paper provides a brief overview of remote sensing technology from the perspective of global change research.

Description: This paper presents the results of the correlation analysis of the Skylab S-193 13.9 GHz Radiometer/Scatterometer data. Computer analysis of the S-193 data shows more than 50 percent of the radiometer and scatterometer data are uncorrelated. The correlation coefficients computed for the data gathered over various ground scenes indicates the desirability of using both active and passive sensors for the determination of various Earth phenomena.

Description: Four radiometric correction methods for the reduction of slope-aspect effects in a Landsat TM data set are tested in a mountainous test site with regard to their physical soundness and their influence on forest classification, as well as on the visual appearance of the scene. Excellent ground reference information and a fine-resolution DEM allowed precise assessment of the applicability of the methods under investigation. The results of the study presented here demonstrate the weakness of the classical cosine correction method for radiometric correction in rugged terrain. The statistical, Minnaert and C-correction approaches, however, yielded an improvement of the forest classification and an impressive reduction of the visual topography effect.

Description: Development of a first-order radiative transfer model for predicting backscatter from tree canopies has been underway at the University of Michigan Radiation Laboratory for some time. This model is known as the Michigan Microwave Canopy Scattering (MIMICS) model. This article presents the second-generation MIMICS model (MIMICS II) which accounts for canopies with discontinuous (open) crown layer geometries. MIMICS II models open crown layers by treating the location, size, and shape of the individual tree crowns as random variables. The backscattering coefficients for the canopy are then determined by introducing statistics derived from these parameters into the radiative transfer solution. Application of the radiative transfer equations to the discontinuous canopy geometry is presented. The resulting model is a robust fully polarimetric solution that is applicable over a wide variety of canopy architectures. Model simulations are compared to results generated with the continuous canopy model. The effect of the open crown geometry is found to be most significant at shallow incidence angles and at high frequencies for trees with well-developed crowns. Under these conditions, the gaps in the crown layer give rise to a notable increase in crown layer transmissivity which allows the radar to see through to the lower layers of the canopy more easily, thereby directly affecting the backscatter contribution of the trunks and ground.

Description: Experimental studies are performed on some coniferous trees (Austrian pine, Nordmann spruce, and Norway spruce) to investigate the relation between the tree architecture and radar signal at X-band. For a single tree, the RCS is measured as a function of the scatterer location at 90 deg incidence. It is found that the main scatterers are the leafy branches and the difference between sigma(vv) and sigma(hh) is significant at the upper portion of the tree. At the lower portion of the tree, sigma(vv) and sigma(hh) have almost the same level. For a group of trees the angular trends of sigma(vv) and sigma(hh) are measured. It is found that the levels of sigma(vv) and sigma(hh) are of the same order, but their angular trends vary from one tree species to the other depending on the tree species structure. The interpretation of these experimental results is carried out with the help of a theoretical model which accounts for the structure of the tree. According to this theoretical study, the major scattering trend is due to the leaves, while the perturbation to the angular trend and the level difference between sigma(vv) and sigma(hh) are due to the branch orientation distributions (i.e., the tree architecture).

Description: The feasibility of using imaging spectrometry in studies of playa evaporites is demonstrated by mapping efflorescent salt crusts in Death Valley (California), using Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data and a recently developed least-squares spectral band-fitting algorithm. It is shown that it was possible to remotely identify eight different saline minerals, including three borates that have not been previously reported for the Death Valley efflorescent crusts: hydroboracite, pinnoite, and rivadavite. The three borates are locally important phases in the crusts; at least one of them, rivadavite, appears to be forming directly from brine.

Description: Data on chlorophyll content and bathymetry of Lake Tahoe obtained on August 9, 1990 by the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) are compared to concurrent in situ surface and in-water measurements. Measured parameters included profiles of percent transmission of monochromatic light, stimulated chlorophyll fluorescence, photosynthetically available radiation, spectral upwelling and downwelling irradiance, and upwelling radiance. Several analyses were performed illustrating the utility of the AVIRIS over a dark water scene. Image-derived chlorophyll concentration compared extremely well with that measured with bottle samples. A bathymetry map of the shallow parts of the lake was constructed which compares favorably with published lake soundings.

Description: Remotely sensed optical and microwave data can be synergistically used to infer land surface properties. Optical data can be used to estimate surface albedo, radiation absorption by vegetation canopies and their photosynthetic efficiencies. Vegetation canopy reflectance at red and near-infrared wavelengths can be used to correct for vegetation effect on microwave emissivities at low frequencies for estimating soil moisture. Optical data can also provide information about surface and air temperatures, precipitable water vapor, cloud top temperature and its water content. This information can be utilized to correct microwave data for atmospheric effects. These points are illustrated with theoretical analyses and by application to satellite data. The basic physical mechanisms operative at the various wavelengths are also discussed.

Description: Quantitative use of remote multispectral measurements to study and map land surface evapotranspiration has been a challenging issue for the past 20 years. Past work is reviewed against process physics. A simple two-layer combination-type model is used which is applicable to both vegetation and bare soil. The theoretic analysis is done to show which land surface properties are implicitly defined by such evaporation models and to assess whether they are measurable as a matter of principle. Conceptual implications of the spatial correlation of land surface properties, as observed by means of remote multispectral measurements, are illustrated with results of work done in arid zones. A normalization of spatial variability of land surface evaporation is proposed by defining a location-dependent potential evaporation and surface temperature range. Examples of the application of remote based estimates of evaporation to hydrological modeling studies in Egypt and Argentina are presented.

Description: Examples are presented of applications of a fast Fourier transform algorithm to analyze time series of images of Normalized Difference Vegetation Index values. The results obtained for a case study on Zambia indicated that differences in vegetation development among map units of an existing agroclimatic map were not significant, while reliable differences were observed among the map units obtained using the Fourier analysis.

Description: This paper discusses a multisensor satellite approach for the study of hydrological applications. Spectral as well as spatial and temporal characteristics of specific operational and planned instruments applicable to hydrology are presented. A hydrology specific series of sensors are proposed to fill the gaps not covered by the current and planned systems. We have called this hypothetical platform HYDROSAT. In addition, the trade-offs between a geostationary satellite and a polar orbiter are explored.

Description: The two-terminal alternating current impedance of Li/TiS2 rechargeable cells was studied as a function of frequency, state-of-charge, and extended cycling. Analysis based on a plausible equivalent circuit model for the Li/TiS2 cell leads to evaluation of kinetic parameters for the various physicochemical processes occurring at the electrode/electrolyte interfaces. To investigate the causes of cell degradation during extended cycling, the parameters evaluated for cells cycled 5 times were compared with the parameters of cells cycled over 600 times. The findings are that the combined ohmic resistance of the electrolyte and electrodes suffers a tenfold increase after extended cycling, while the charge-transfer resistance and diffusional impedance at the TiS2/electrolyte interface are not significantIy affected. The results reflect the morphological change and increase in area of the anode due to cycling. The study also shows that overdischarge of a cathode-limited cell causes a decrease in the diffusion coefficient of the lithium ion in the cathode.

Description: This paper shows how the radar scattering from vegetated areas is affected by the topography of the surface underneath the vegetation. It is shown, using a discrete scatterer model, that the dominant scattering mechanism may change drastically when the ground surface is tilted relative to the horizontal. In the case of a horizontal ground surface, total scattering may be dominated by scattering off the tree trunks, followed by a reflection off the ground surface. For a relatively small tilt in the ground surface (about 2 deg from horizontal), the ground-trunk interaction term may be replaced by scattering from the branches alone as the dominant scattering mechanism. We also show that the effect of the topography is more pronounced for scattering by longer wavelengths, and discuss the implications on algorithms designed to infer forest woody biomass and soil and vegetation moisture using polarimetric SAR data. The effect of the topography on the scattering behavior from forested areas is illustrated with images acquired by the NASA/JPL three-frequency polarimetric SAR over the Black Forest in Germany.

Description: Land surface hydrologic-atmospheric interactions in humid and semi-arid watersheds were investigated. Active and passive microwave sensors were used to estimate the spatial and temporal distribution of soil moisture at the catchment scale in four areas. Results are presented and discussed. The eventual use of this information in the analysis and prediction of associated hydrologic processes is examined.

Description: Regional ecological studies are considered in the context of the global change problem. The Kursk-91 international experiment is used to illustrate applications of remote sensing data and data bases of field experiments for assessment of parameters of the state of the soil and vegetative cover and subsequent study of biospheric stability on the basis of regular satellite observations.

Description: The visible bands of the Landsat Thematic Mapper (TM) sensor were used in an empirical assessment of seagrass biomass on shallow banks near Lee Stocking Island in the Bahamas. The TM bands were transformed to minimize the depth-dependent variance in the bottom reflectance signal. Regression analyses were performed between the transformed bands and field measurements of seagrass standing crop (above-ground biomass). Regression equations using spectral data accounted for up to 80 per cent of the variability in seagrass biomass. The unexplained variance was ascribed to variations in bottom sediment color.

Description: The single scattering albedo and optical depth of typical savanna vegetation in Botswana (Africa) have been determined by inverse modelling using satellite observed microwave signatures and surface soil moisture. Soil emissivity was modelled using a multi-layer radiative transfer model. The study is based on large scale surface moisture data and Nimbus/SMMR 6-6 GHz and 37 GHz dual polarized brightness temperatures over a 3-year period. As compared to the optical depths, the derived single scattering albedos displayed only minor seasonal variations, whereas the values fit well within the range reported in the literature from laboratory and field experiments. Both 6-6 and 37GHz optical depths were found to be significantly related to NDVI-values derived from NOAA/AVHRR.

Description: The hypothesis tested was that some part of the ecosystem-dependent variability of vegetation indices was attributable to the effects of light specularly reflected by leaves. 'Minus specular' indices were defined excluding effects of specular light which contains no cellular pigment information. Results, both empirical and theoretical, show that the 'minus specular' indices, when compared to the traditional vegetation indices, potentially provide better estimates of the photosynthetic activity within a canopy - and therefore canopy primary production - specifically as a function of sun and view angles.

Description: A linear mixing model was applied to coarse spatial resolution data from the NOAA Advanced Very High Resolution Radiometer. The reflective component of the 3.55-3.95 micron channel was used with the two reflective channels 0.58-0.68 micron and 0.725-1.1 micron to run a constrained least squares model to generate fraction images for an area in the west central region of Brazil. The fraction images were compared with an unsupervised classification derived from Landsat TM data acquired on the same day. The relationship between the fraction images and normalized difference vegetation index images show the potential of the unmixing techniques when using coarse spatial resolution data for global studies.

Description: Recently, a number of studies have investigated the use of the 37 GHz channels of the Nimbus-7 Scanning Multichannel Microwave Radiometer (SMMR) for vegetation monitoring and for studying synergisms between the SMMR and the NOAA Advanced Very High Resolution Radiometer (AVHRR). The approaches are promising but raise a number of issues concerning interpretation of the results, specifically on the relative effects of vegetation and other surface and atmospheric characteristics on the observed signal. This article analyzes the 37 GHz Microwave Polarization Difference Temperature (MPDT) in terms of its sensitivity to surface and atmospheric parameters. For this, a radiative transfer model is used which indicates some limitations of the MPDT index and suggests the importance of accounting for atmospheric effects in the data analysis. An alternative approach to the MPDT, including lower SMMR frequencies than 37 GHz, is discussed.

Description: Spaceborne laser altimeter systems intended to operate at lunar and Martian orbits are reviewed. Laser altimeter systems capable of long lifetimes with centimeter precision ranging electronics are considered to be essential components of NASA's EOS.

Description: The Visiting Investigator Program (VIP) developed at NASA-Stennis' Science and Technology Laboratory (STL) allows U.S. industry to use the specialized resources of STL in the fields of remote sensing and GIS, with a view to the development of new commercial processes and improved services. Attention is given to the novel agreement mechanisms developed by NASA to implement VIP. These agreements encompass a memorandum of understanding, a technical exchange agreement, a sponsored-transfer agreement, a proprietary work agreement, and a joint endeavor agreement.

Description: Topographic profiles at 25- and 5-cm horizontal resolution for three sites along a lava flow on Kilauea Volcano are presented, and these data are used to illustrate techniques for surface roughness analysis. Height and slope distributions and the height autocorrelation function are evaluated as a function of varying lowpass filter wavelength for the 25-cm data. Rms slopes are found to increase rapidly with decreasing topographic scale and are typically much higher than those found by modeling of Magellan altimeter data for Venus. A more robust description of the surface roughness appears to be the ratio of rms height to surface height correlation length. For all three sites this parameter falls within the range of values typically found from model fits to Magellan altimeter waveforms. The 5-cm profile data are used to estimate the effect of small-scale roughness on quasi-specular scattering.

Description: An improved method of estimating fractal surface dimensions has been developed. The accuracy of this method is illustrated using artificially generated fractal surfaces. A slightly different from usual concept of linear dimension is developed, allowing a direct link between that and the corresponding surface dimension estimate. These methods are applied to a series of images of lava flows, representing a variety of physical and chemical conditions. These include lavas from California, Idaho, and Hawaii, as well as some extraterrestrial flows. The fractal surface dimension estimations are presented, as well as the fractal line dimensions where appropriate.

Description: Three AVHRR-LAC data sets acquired in September 1990 and January 1991 were used to map the forest resources of Madagascar. The island was partitioned into four strata to include: (1) the western hardwoods, (2) the central grasslands, (3) the eastern rainforest, and (4) spiny forest. Each stratum was classified separately using AVHRR-LAC data in conjunction with 1984-1988 Landsat-MSS photoproducts. The results of AVHRR classification indicate that approximately 11 percent of the island is covered by forest. Estimates of forest area, by stratum, are as follows: western hardwoods, 6697 sq km; central grasslands, 2830 sq km; eastern rainforest 34,167 sq km; and spiny forest, 17,224 sq km. The total forest area on the 587,041 sq km island is estimated to be 60,918 sq km. The AVHRR forest map was compared to a mid-1970s land cover map which was developed using Landsat-MSS photoproducts. The average class agreement between the mid 1970s ground reference map and the 1990 AVHRR-LAC map was 78.2 percent, the overall accuracy was 81.1 percent. Much of the per-pixel disagreement between the ground reference and AVHRR maps involved areas identified as forest in the 1970s and as nonforest in 1990.

Description: We describe an application of a scale-space clustering algorithm to the classification of a multispectral and polarimetric SAR image of an agricultural site. After the initial polarimetric and radiometric calibration and noise cancellation, we extracted a 12-dimensional feature vector for each pixel from the scattering matrix. The clustering algorithm was able to partition a set of unlabeled feature vectors from 13 selected sites, each site corresponding to a distinct crop, into 13 clusters without any supervision. The cluster parameters were then used to classify the whole image. The classification map is much less noisy and more accurate than those obtained by hierarchical rules. Starting with every point as a cluster, the algorithm works by melting the system to produce a tree of clusters in the scale space. It can cluster data in any multidimensional space and is insensitive to variability in cluster densities, sizes and ellipsoidal shapes. This algorithm, more powerful than existing ones, may be useful for remote sensing for land use.

Description: Results are presented of an investigation to determine the degree to which digitally processed Landsat TM imagery can be used to discriminate among vegetated lava flows of different ages in the Menengai Caldera, Kenya. A selective series of five images, consisting of a color-coded Landsat 5 classification and four color composites, are compared with geologic maps. The most recent of more than 70 postcaldera flows within the caldera are trachytes, which are variably covered by shrubs and subsidiary grasses. Soil development evolves as a function of time, and as such supports a changing plant community. Progressively older flows exhibit the increasing dominance of grasses over bushes. The Landsat images correlated well with geologic maps, but the two mapped age classes could be further subdivided on the basis of different vegetation communities. It is concluded that field maps can be modified, and in some cases corrected by use of such imagery, and that digitally enhanced Landsat imagery can be a useful aid to field mapping in similar terrains.

Description: The present study shows that current bipolar Li/TiS2 batteries using a 0.38 mm thick TiS2 bipolar plate can yield moderate specific power and also high specific energy battery. The computer design studies project that a 100 V, 10 A h bipolar Li/TiS2 battery can achieve 150 W h/kg, 210 W h/l, and 150 W/kg. The unoptimized experimental bipolar Li/TiS2 batteries (3 cells, 90 mA h) exhibited 47 W h/kg, 90 W h/l, and 140 W/kg. Preliminary results on the cycleability of the bipolar batteries are demonstrated. The results also show that enhanced rate capability can be achieved by using pulse discharge and longer rest period between pulses.

Description: A high power, 28 V, 330 A h, active lithium thionyl chloride battery has been developed for use as main and payload power sources on an expendable launch vehicle. Nine prismatic cells, along with the required electrical components and a built-in heater system, are efficiently packaged resulting in significant weight savings over presently used silver-zinc batteries. The high rate capability is achieved by designing the cells with a large electrochemical surface area and impregnating an electrocatalyst, polymeric phthalocyanine, into the carbon cathodes. Passivation effects are reduced with the addition of sulfur dioxide into the thionyl chloride electrolyte solution. The results of conducting a detailed thermal analysis are utilized to establish the heater design parameters and the thermal insulation requirements of the battery. An analysis of cell internal pressure and vent characteristics clearly illustrates the margins of safety under different operating conditions. Performance of fresh cells is discussed using polarization scan and discharge data at different rates and temperatures. Self-discharge rate is estimated based upon test results on cells after storage. Results of testing a complete prototype battery are described.

Description: Measurements of the C-band (wavelength = 5 cm) radar cross section of an area in the Brooks Range foothills on the North Slope of Alaska using images from the ERS-1 satellite show significant temporal changes. These changes are strongly correlated with elevation and hillslope orientation and are greatest on some of the elevated areas and weaker in river drainages. By constructing 'difference images' using various image pairs, and by analyzing climatological and hydrological data from the site, we conclude that the radar backscatter changes are largely due to changes in soil and vegetation liquid water content induced by freeze/thaw events. The correlation with topography in the difference images arises from the dependence of vegetation, organic layer thickness, and volumetric water content on hillslope position and orientation. These results demonstrate the viability of radar backscatter intensity comparisons using repeat-pass images as a means of change detection.

Description: This research attempts to map small-scale vegetation changes in Mexico. Forty-eight weeks of coarse resolution Advanced Very High Resolution Radiometer Normalized Difference Vegetation Index (NDVI), a digitized climax vegetation map, land cover samples from space shuttle photographs and actual vegetation samples were used as inputs. Principal components analyses and a clustering algorithm were applied to the NDVI data to generate a single layer that was stratified by the climax vegetation zones map. The purpose is to create a new layer that differentiates climax vegetation (hypothesized potential vegetation) from non-climax vegetation land covers. One of the keys to developing a present-day vegetation map was differentiating intrazone land covers based on the stratification; as great as 75% of the sampled land cover types differed from the climax vegetation. The present-day vegetation map achieved 80% classification accuracy when calculated from available ground reference data. About 55% of the temperate zones and 37% of the tropical zones were found to contain original climax vegetation. Most changes coincide with areas of major agricultural activity.

Description: The photographic and videographic documentation of the Earth during STS-46 mission has enhanced the Space Shuttle Earth Observations Project (SSEOP) database. Increasing numbers of scientists are using this database; many are downloading the imagery from our electronic database for specific scientific analyses. We believe the scientific returns of the Earth Observations photography from this mission will add to the global change databases and will contribute to the better understanding of our home planet. The use of manned space flights in understanding the global process first hand is a vital component in NASA's Mission to Planet Earth. The following are discussed along with photographs from the mission: landforms and geologic observation; environmental observations; meteorological/atmospheric observation; and oceanographic observations.

Description: The advantages of the astronaut photography during Space Shuttle missions are briefly examined, and the scope and applications of the Space Shuttle earth observations photography database are discussed. The global and multidisciplinary nature of the data base is illustrated by several examples of geologic applications. These include the eruption of Mount Pinatubo (Philippine Islands), heat flow and ice cover on Lake Baikal in Siberia (Russia), and windblown dust in South America. It is noted that hand-held photography from the U.S. Space Shuttle provides unique remotely-sensed data for geologic applications because of the combination of varying perspectives, look angles, and illumination, and changing resolution resulting from different lenses and altitudes.

Description: A review of the imagery acquired during the STS 50 mission of the Space Shuttle is presented. The earth viewing photography from this flight includes photos of dust plumes over several portions of the Red Sea, Arabian Sea, Persian Gulf, the Mediterranean Sea, and the Atlantic Ocean. Over land, prominent dust plumes were seen over Iraq, North Africa, Sudan, and West Africa. The color infrared photography includes images of the tropical rain forests of South America and South and Southeast Asia. Other examples include photographs of floods in Argentina, photos of Lake Chad in Africa, Coastal Madagascar, the Aswan dam and the Nile, geologic features of North Africa, the center pivot irrigation land areas of Saudi Arabia, flooding in Asian rivers, and sediment plumes of South American and South and Southeast Asian coasts.

Description: An Automated Bidirectional Reflection Acquisition Measurement System (ABRAMS) has been constructed to facilitate measurement of bidirectional reflectance from soil and vegetative samples in the laboratory. The system illuminates a sample with linearly-polarized laser light, lambda = 632.8 nm, and measures the like- and cross-polarized scattered intensities over half a hemisphere. System design and polarized bidirectional reflectance measurements from a soil sample and SiO2 spherical particles are discussed in this work. It is shown that polarization information in the plane of incidence is useful for identifying certain scattering mechanisms associated with soil reflectance. This is because the like-polarized intensity, Ivv, is influenced by single-scattered light and the cross-polarized intensity, IHv, is strongly influenced by multiple-scattered light. For example, comparable levels of Ivv and IHv indicated that the reflectance of soils, is dominated by significant multiple scattering because single scattering causes minimal depolarization in the plane of incidence.

Description: A multistage sampling procedure using image processing, geographical information systems, and analytical photogrammetry is presented which can be used to guide the collection of representative, high-resolution spectra and discrete reflectance targets for future satellite sensors. The procedure is general and can be adapted to characterize areas as small as minor watersheds and as large as multistate regions. Beginning with a user-determined study area, successive reductions in size and spectral variation are performed using image analysis techniques on data from the Multispectral Scanner, orbital and simulated Thematic Mapper, low altitude photography synchronized with the simulator, and associated digital data. An integrated image-based geographical information system supports processing requirements.

Description: The cost involved in the performance of the standard operations for the manufacture of silicon wafers is insignificant in the case of space photovoltaics applications. It is, however, a decisive factor with respect to terrestrial applications of silicon photovoltaic devices. In 1975, a program was, therefore, begun to develop low cost silicon solar arrays for terrestrial applications. The goal was silicon-based photovoltaic (PV) modules ready for installation at a selling price of $0.50/watt (1975 dollars). Sheet and ribbon silicon growth held out the promise of reduced cost through continuous operation, high material throughput, high material utilization efficiency, and a product whose shape lent itself to the assembly of high packing density modules. Attention is given to ribbon growth technologies, sheet technology generic problems, and ribbon cell and module technology status. It is concluded that the potential for crystalline ribbon silicon appears to be better today than ever before.

Description: A goal of future synthetic aperture radar (SAR) system design is to yield the radiometrically accurate imagery necessary for use in classification problems. To accomplish this, a reliable calibration technique must be developed. Many such techniques have been proposed (e.g., Stiles and Holtzman, 1982); however, until now, none have been tested on spaceborne SAR digital data. In this paper, a method of significantly increasing the reproducibility of several independent Seasat SAR data sets of a test site using an automated correction procedure is described.

Description: The present investigation is concerned with the formulation of energy management strategies for stand-alone photovoltaic (PV) systems, taking into account a basic control algorithm for a possible predictive, (and adaptive) controller. The control system controls the flow of energy in the system according to the amount of energy available, and predicts the appropriate control set-points based on the energy (insolation) available by using an appropriate system model. Aspects of adaptation to the conditions of the system are also considered. Attention is given to a statistical analysis technique, the analysis inputs, the analysis procedure, and details regarding the basic control algorithm.

Description: Measurements of the transient characteristics associated with the discharge of a simulated solar array are presented. A capacitively coupled probe is used to measure the discharge current, and antennas are used to measure the electromagnetic radiation. Discharges were observed at low surface voltages and several modes of discharge were observed. The maximum discharge current is found to be 0.2 A. This value is several orders of magnitude higher than that reported by previous measurements. Experimental evidence suggests that the inverted voltage gradient is a very likely triggering mechanism for solar array discharges.

Description: The improved spatial resolution of the new earth resources satellites will increase the need for effective utilization of spatial information in machine processing of remotely sensed data. One promising technique is scene segmentation by region growing. Region growing can use spatial information in two ways: only spatially adjacent regions merge together, and merging criteria can be based on region-wide spatial features. A simple region growing approach is described in which the similarity criterion is based on region mean and variance (a simple spatial feature). An effective way to implement region growing for remote sensing is as an iterative parallel process on a large parallel processor. A straightforward parallel pixel-based implementation of the algorithm is explored and its efficiency is compared with sequential pixel-based, sequential region-based, and parallel region-based implementations. Experimental results from on aircraft scanner data set are presented, as is a discussioon of proposed improvements to the segmentation algorithm.

Description: The scientific instruments comprising the OSTA-1 package flown on the second Shuttle mission (November 12-14, 1981) are listed, and the Shuttle Imaging Radar (SIR-A) experiments are examined in detail: SIR-A operated for 8 h and obtained images covering more than 10 million sq km at 40-m resolution. The images were recorded on photographic film and processed in holographic form at JPL, and data for Southern Europe and parts of Africa were distributed to French scientists by the Groupement pour le Developpement de la Teledetection Aerospatiale. The main areas of research were environmental studies and geology, and the SIR-A images were used in combination with aerial photography, thematic maps, and Landsat images. The technical specifications of the SIR-B radar planned for STS-17 in 1984 are compared with those of SIR-A and Seasat SAR in tables.

Description: The use of remote sensing in resource exploration is reviewed, with emphasis placed on new developments in high spectral resolution remote-sensing techniques for mineralogic and vegetation mapping. Topics discussed include aerial photography and satellite remote sensing, concepts and principles of spectral data collection, spectral properties of rocks and minerals, spectral properties of vegetation, and botanical aspects of geochemical stress. The discussion also covers applications of Landsat multispectral scanner data to lithologic and geobotanic studies and the future development of data acquisition and data interpretation techniques.

Description: In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Description: The development of a preprocessing unit for Landsat Thematic Mapper (TM) data for the Earth Observations Data Laboratory at Johnson Space Center is reported. The background of the project is sketched, including the greatly increased data-handling requirements compared to MSS, the influence of the JPL VICAR system on the system design, and the completeness of the GSFC SCROUNGE (LASLIB) TM data tapes. The design approach and realization are discussed, and the performance and transportability of the preprocessor programs (totaling about 2000 lines of source code in FORTRAN and IBM Assembly languages) are indicated. The system is able to read the TM image tapes, extract areas of interest to particular studies, and register the extracted imagery to suitable references. Ancillary programs include image enhancement, rotation, filtering and pixel-size modification.

Description: Features of the NASA Regional Application Program for providing state and local land management agencies an opportunity to assess the usefulness of emerging remote sensing technology are described. The Program guidelines necessitated configuring software for local facilities, assuring that the aggncy involved furnished manpower, and applying the technology to local needs. The study focused on the southwestern U.S., particularly for purposes of water management, federal/state ownership/policy, energy development, environmental impact issues, timber and range inventory, fire control, and urban expansion. Demonstration projects were conducted in various topics, according to the state surveyed, with the success of the projects determined by the willingness of the agencies to continue with the technology, which happened in several cases.

Description: The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) is a facility instrument selected for launch in 1998 on the first in a series of spacecraft for NASA's Earth Observing System (EOS). The ASTER instrument is being sponsored and built in Japan. It is a three telescope, high spatial resolution imaging instrument with 15 spectral bands covering the visible through to the thermal infrared. It will play a significant role within EOS providing geological, biological, land hydrological information necessary for intense study of the Earth. The operational capabilities for ASTER, including the necessary interfaces and operational collaborations between the US and Japanese participants, are under development. EOS operations are the responsibility of the EOS Project at NASA's Goddard Space Flight Center (GSFC). Although the primary EOS control center is at GSFC, the ASTER control facility will be in Japan. Other aspects of ASTER are discussed.

Description: National Space Development Agency of Japan (NASDA) has conducted the research and development (R&D) of battery cells for space use. A new R&D program about a Nickel-Metal Hydride (Ni-MH) cell for space use from this year, based on good results in evaluations of commercial Ni-MH cells in Tsukuba Space Center (TKSC), was started. The results of those commercial Ni-MH cell's evaluations and recent status about the development of Ni-MH cells for space use are described.

Description: A discussion of the development of a fundamental cell model is presented in vugraph format. The nickel oxide layer is described in terms of the electronic conductivity of the oxide layer and proton diffusion through the oxide layer. The kinetic and conductivity expressions for the cadmium electrode were improved. The development process yielded performance predictions that are significantly improved.

Description: The following observations were made during the first occultation period: (1) C/D ratios tend to be higher during the initial and final segment of the occultation period; (2) the net overcharge parameter is useful in assessing C/D's; (3) small peak power cusps were present during the initial and final segment of the occultation period--no cusps during the remaining period; (4) small differential voltages (less than 12 mV) were recorded; and (5) the peak charge current was within the recommended limits. In summary, the batteries are operating within recommended limits, and their performance is excellent.

Description: Research and operational experience with capacity fade in nickel cadmium and nickel hydrogen cells are summarized in outline form. The theoretical causes of capacity fade are reviewed and the role of cell storage, positive electrodes, and cobalt additives are addressed. Three examples of observed capacity fade are discussed: INTELSAT 5, INTELSAT 6, and an Explorer platform. Finally, prevention and recovery methods are addressed and the current status of Eagle Picher/Hughes research is discussed.

Description: During recent years there have been a number of instances where the capacity of nickel hydrogen battery cells has proven to be unstable during storage. The capacity losses seen after periods of cell or battery storage have typically varied from only a small amount of fading, up to about 30 percent of the total cell capacity. Detailed studies into the root causes for such fading have been carried out in a number of instances. This report provides an overview of the different mechanisms that have been found to be responsible for such capacity fading in nickel hydrogen cells, and summarizes the presently available data on how each responsible mechanism affects ultimate cell cycle life.

Description: Over the past 5 years, COMSAT has performed numerous destructive physical analyses (DPA's) on NASA-Goddard-supplied nickel-cadmium (Ni/Cd) cells. The samples included activated but uncycled cells, wet stored cells, cycled cells, and anomalous cells. The DPA's provided visual, morphological, and chemical analyses of the cell components. The DPA data for the analyzed cells are presented. For the cells investigated, the leading cause of poor performance, as determined by DPA, has been poor negative electrode utilization, which resulted in negative-electrode-limiting operation.

Description: The topics covered are presented in viewgraph form and include a flight program history and in-house activities. Some of the in-house activities addressed include secondary battery/cell testing and Hubble Space Telescope Test data updates involving the NiCd type 40 test - battery 1 and 2, the NiCd type 41 test battery, the general electric battery, the NiCd six-battery system, the six four-cell packs, fourteen-cell pack, three four-cell packs, the NiH2 six-battery system, and the flight spare battery. A general test data update is also presented for the twelve-cell pack, the four four-cell packs, the reconditioning test, and planned Ni-MH testing.

Description: The topics covered are presented in viewgraph form and include the following: the Advanced Communications Technology Satellite; the Space Station Freedom (SSF) photovoltaic power module division; Ni/H2 battery and cell design; individual pressure vessel (IPV) nickel-hydrogen cell testing SSF support; the LeRC Electrochemical Technology Branch; improved design IPV nickel-hydrogen cells; advanced technology for IPV nickel-hydrogen flight cells; a lightweight nickel-hydrogen cell; bipolar nickel-hydrogen battery development and technology; aerospace nickel-metal hydride cells; the NASA Sodium-Sulfur Cell Technology Flight Experiment; and the lithium-carbon dioxide battery thermodynamic model.

Description: The topics covered are presented in viewgraph form and include the following: flight project support activities for TOPEX and the Mars Observer; and research/development and engineering activities for NiCd model development, secondary lithium battery development, the sodium-NiCl2 moderate temperature battery, Li-SOCl2 batteries for the Centaur launch vehicle, and direct hydrocarbon/methanol fuel cells.

Description: Viewgraphs of the sodium sulfur program are presented. Sodium sulfur low earth orbit (LEO) cells are described. Topics covered include cell sizes, areas of improvement, and NaS cell testing. Sodium sulfur cell and battery designs continue to evolve with significant improvement demonstrated in resistance, rechargeability, cycle life, energy density, and electrolyte characterization.

Description: The multicell common pressure vessel (CPV) nickel hydrogen battery manufactured by Johnson Controls Battery Group, Inc. has completed full flight qualification, including random vibration at 19.5 g for two minutes in each axis, electrical characterization in a thermal vacuum chamber, and mass-spectroscopy vessel leak detection. A first launch is scheduled for late in 1992 or early 1993 by the Naval Research Laboratory (NRL). Specifics of the launch date are not available at this time due to the classified nature of the program. Release of orbital data for the battery is anticipated following the launch.

Description: Gates Aerospace Batteries in conjunction with Gates Energy Products (GEP) has been developing NiMH technology for aerospace use since 1990. GEP undertook the development of NiMH technology for commercial cell applications in 1987. This program focused on wound cell technology for replacement of current NiCd technology. As an off shoot of this program small, wound cells were used to evaluate initial design options for aerospace prismatic cell designs. Early in 1991, the first aerospace prismatic cell designs were built in a 6 Ah cell configuration. These cells were used to initially characterize performance in prismatic configurations and begin early life cycle testing. Soon after the 6 Ah cells were on test, several 22 Ah cells were built to test other options. The results of testing of these cells were used to identify potential problem areas for long lived cells and develop solutions to those problems. Following these two cell builds, a set of 7 Ah cells was built to evaluate improvements to the technology. To date results from these tests are very promising. Cycle lives in excess of 2,200 LEO cycles at 50 percent DoD were achieved with cells continuing on test. Results from these cell tests are discussed and data presented to demonstrate feasibility of this technology for aerospace programs.

Description: The topics covered are presented in viewgraph form and include the following: Eagle-Picher heritage - single pressure vessel (SPV) technology; SPV units in process at Eagle-Pitcher; design features; basic battery design features; cell development considerations; SPV boiler plate cell; cell development activity; SPV cell capacity test - charge and discharge; and current plans.

Description: A 3.5 inch rabbit-ear-terminal nickel-hydrogen cell has been designed and tested to deliver high capacity at a C/1.5 discharge rate. Its specific energy yield of 60.6 wh/kg is believed to be the highest yet achieved in a slurry-process nickel-hydrogen cell, and its 10 C capacity of 113.9 AH the highest capacity yet made at a discharge rate this high in the 3.5 inch diameter size. The cell also demonstrated a pulse capability of 180 amps for 20 seconds. Specific cell parameters, performance, and future test plans are described.

Description: The French and European Space Agencies (CNES, ESA) have been continuously contributing to the development of synthetic aperture focusing technique (SAFT) Ni-H2 technology since 1985. An important effort has been devoted to improving scientific knowledge to enhancing industrial experience and to promoting SAFT as an official back up source for the European domestic telecommunications market as a battery supplier. Fundamental aspects have been investigated in both industrial and university labs as essential R&D supports. The objectives of this paper are the following: to explain which technical areas, components, and processes have been covered by our studies; to show the results of this work; to establish the status which has been reached and what the standard SAFT individual pressure vessels (IPV) design's main features are; and to present our plans for the near future.

Description: The topics covered are presented in viewgraph form and include the following: the Hubble Space Telescope (HST) Mission; system constraints; battery specification; battery module; simplified block diagram; cell design summary; present status; voltage decay; system depth of discharge; pressure since launch; system capacity; eclipse time vs. trickle charge; capacity test objectives; and capacity during tests.

Description: The topics covered are presented in viewgraph form and include the following: reasons for developing a 2.5 in. nickel-hydrogen cell; the 2.5 in. nickel-hydrogen development history; RNHC-6-1 cell design; RNHC-6-1 charge voltage at 0.6 A; RNHC-6-1 discharge voltage at 3.0 A; RNHC-6-1 qualification testing; flight unit testing; RNHC-6-1 technical data; technical data for the SAR-10027 Battery; and RNHC-10-1 life test.

Description: This paper summarizes an effort by Gates Aerospace Batteries (GAB) and the Reliability Analysis Center (RAC) to analyze survivability data for both General Electric and GAB NiCd cells utilized in various spacecraft. For simplicity sake, all mission environments are described as either low Earth orbital (LEO) or geosynchronous Earth orbit (GEO). 'Extreme value statistical methods' are applied to this database because of the longevity of the numerous missions while encountering relatively few failures. Every attempt was made to include all known instances of cell-induced-failures of the battery and to exclude battery-induced-failures of the cell. While this distinction may be somewhat limited due to availability of in-flight data, we have accepted the learned opinion of the specific customer contacts to ensure integrity of the common databases. This paper advances the preliminary analysis reported upon at the 1991 NASA Battery Workshop. That prior analysis was concerned with an estimated 278 million cell-hours of operation encompassing 183 satellites. The paper also cited 'no reported failures to date.' This analysis reports on 428 million cell hours of operation emcompassing 212 satellites. This analysis also reports on seven 'cell-induced-failures.'

Description: Two lots of NASA standard 50 A.H. Ni-Cd battery cells, manufactured by Gates Aerospace Batteries and built into batteries by McDonnell Douglas, have experienced significant performance problems. The two lots were used on the Compton Gamma Ray Observatory and the Upper Atmosphere Research Satellite. Both of these satellites are Low Earth Orbital (LEO) satellites containing batteries on a parallel bus charged to NASA standard V/T curves using a NASA standard power regulator. The following preliminary conclusions were reached: (1) several plate and cell parameters have migrated within their spec limits over the years (in some cases, from one extreme to the other); (2) several parametric relationships, not generally monitored and therefore not under specification control, have also migrated over the years; (3) many of these changes appear to have taken place as a natural consequence of changes in GE/GAB materials and processes; (4) several of these factors may be 'conspiring' to aggravate known cell failure mechanisms (factors such as heavier plate, less teflon and/or less-uniform teflon, and less electrolyte) but all are still in spec (where specs exist); (5) the weight of the evidence collected to characterize the anomalies and to characterize the negative electrode itself, strongly suggests that alterations to the structure, composition, uniformity, and efficiency of the negative electrode are at the heart of the battery performance problems currently being experienced; and (6) further investigation at all levels (plate, cell, battery, and system) continues to be warranted.

Description: The generic qualification of aerospace nickel-cadmium cells is discussed. The test program includes the following: all available manufacturers, all available designs, cells from the previous program, and high and low orbit life cycling. It is the purpose of this program to characterize the beginning of life performance.

Description: Tests were conducted to investigate the recovery of capacity lost during open circuit storage of negatively precharged nickel hydrogen batteries. Four Eagle Picher RNH-90-3 cells were used in the tests. Recovery procedures and test results are presented in outline and graphic form.

Description: Test were conducted to evaluate post storage performance of nickel hydrogen cells with various design variables, the most significant being nickel precharge versus hydrogen precharge. Test procedures and results are presented in outline and graphic form.

Description: Tests were conducted on nickel hydrogen batteries to determine the charge efficiency of the nickel electrode as a function of rate and temperature, cell discharge capacity, and capacity fade. Test procedures and results are presented in outline and graphic form.

Description: Cobalt redistribution in nickel active material has been reported. This redistribution was suspected to be related to capacity fading. The objective of this work is to establish a relationship between cobalt redistribution and capacity fading. Microscopic cobalt distribution in nickel active material was studied using three EDX techniques: line scan, point-by-point analysis, and dot maps. Results from this study are presented.

Description: Two 22 cell batteries designed by Martin Marietta were tested. The batteries were rated at 26.5 Amp-Hr. The battery design is characterized by the following: Gates Aerospace 42B030AB15, 11 pos/12 neg, Pellon 2536 separator, passivated pos/teflonated neg. The tests can be summarized as follows: (1) no noticeable capacity loss after storage period; and (2) batteries exhibited larger non-uniformity of cell voltages during constant current charge.

Description: The Hubble Space Telescope (HST) nickel-hydrogen battery module was designed by Lockheed Missile & Space Co (LMSC) and manufactured by Eagle-Picher Ind. (EPI) for the Marshall Space Flight Center (MSFC) as an Orbital Replacement Unit (ORU) for the nickel-cadmium batteries originally selected for this low earth orbit mission. The design features of the HST nickel hydrogen battery are described and the results of an extended charge retention test are summarized.

Description: The results of tests to assess capacity loss in nickel hydrogen cells are presented in outline form. The effects of long storage (greater than 1 month), high hydrogen pressure storage, high cobalt content, and recovery actions are addressed.

Description: The topics covered are presented in viewgraph form and include the following: spacecraft operations, life cycle testing an the Naval Surface Warfare Center (NSWC), and destructive physical analysis at COMSAT laboratories. The subtopics under spacecraft operations are the Solar Anomalous and Magnetospheric Particle Explorer (SAMPEX), the Extreme Ultraviolet Explorer (EUVE), the Upper Atmospheric Research Satellite (UARS), the Compton Gamma Ray Observatory (GRO), the Earth Radiation Budget Satellite (ERBS), and the Hubble Space Telescope (HST). The subtopics under the life cycle testing at NSWC are the following: advanced NiCd cells from Hughes Aircraft Company/Eagle Picher Industries; conventional NiCd cells from Gates Aerospace Batteries; conventional NiCd cells from General Electric; NiCd cells from SAFT; NiH2 celss from Eagle Picher Industries; and data as of 10/26/92.

Description: This study shows recent results of our efforts to develop and verify an algorithm for snow wetness retrieval from a polarimetric SAR (Synthetic Aperture Radar). Our algorithm is based on the first-order scattering model with consideration of both surface and volume scattering. It operates at C-band and requires only rough information about the ice volume fraction in snowpack. Comparing ground measurements and inferred from JPL AIRSAR data, the results showed that the relative error inferred from SAR imagery was within 25 percent. The inferred snow wetness from different looking geometries (two flight passes) provided consistent results within 2 percent. Both regional and point measurement comparisons between the ground and SAR derived snow wetness indicates that the inversion algorithm performs well using AIRSAR (Airborne Synthetic Aperture Radar) data and should prove useful for routine and large-area snow wetness (in top layer of a snowpack) measurements.

Description: Crown closure is one of the input parameters used for forest growth and yield modelling. Preliminary work by Staenz et al. indicates that imaging spectrometer data acquired with sensors such as the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) have some potential for estimating crown closure on a stand level. The objectives of this paper are: (1) to establish a relationship between AVIRIS data and the crown closure derived from aerial photography of a forested test site within the Interior Douglas Fir biogeoclimatic zone in British Columbia, Canada; (2) to investigate the impact of atmospheric effects and the forest background on the correlation between AVIRIS data and crown closure estimates; and (3) to improve this relationship using multiple regression analysis.

Description: Hyperspectral images have many bands requiring significant computational power for machine interpretation. During image pre-processing, regions of interest that warrant full examination need to be identified quickly. One technique for speeding up the processing is to use only a small subset of bands to determine the 'interesting' regions. The problem addressed here is how to determine the fewest bands required to achieve a specified performance goal for pixel classification. The band selection problem has been addressed previously Chen et al., Ghassemian et al., Henderson et al., and Kim et al.. Some popular techniques for reducing the dimensionality of a feature space, such as principal components analysis, reduce dimensionality by computing new features that are linear combinations of the original features. However, such approaches require measuring and processing all the available bands before the dimensionality is reduced. Our approach, adapted from previous multidimensional signal analysis research, is simpler and achieves dimensionality reduction by selecting bands. Feature selection algorithms are used to determine which combination of bands has the lowest probability of pixel misclassification. Two elements required by this approach are a choice of objective function and a choice of search strategy.

Description: The Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) measures spatial images of the total upwelling spectral radiance from 400 to 2500 nm through 10 nm spectral channels. Quantitative research and application objectives for surface investigations require inversion of the measured radiance of surface reflectance or surface leaving radiance. To calculate apparent surface reflectance, estimates of atmospheric water vapor abundance, cirrus cloud effects, surface pressure elevation, and aerosol optical depth are required. Algorithms for the estimation of these atmospheric parameters from the AVIRIS data themselves are described. From these atmospheric parameters we show an example of the calculation of apparent surface reflectance from the AVIRIS-measured radiance using a radiative transfer code.

Description: In 1984, the LDEF (Long Duration Exposure Facility) was placed in LEO (Low Earth Orbit) for a mission planned to last approximately one year. Due to a number of factors, retrieval was delayed until 1990. An experiment, prepared under the direction of JPL, consisted of a test plate with thirty (30) individual thin silicon solar cell/cover samples. The covers consisted of conventional cerium doped microsheet platelets and potential candidate materials, such as FEP Teflon, silicon RTV's, glass resins, polyimides, and a silicone-polyimide copolymer encapsulant. The effects of the LDEF mission environment (micrometeorite/debris impacts, atomic oxygen, UV, and particulate radiation) on the samples are discussed.

Description: The results of post-flight performance testing of the solar cells flown on the Advanced Photovoltaic Experiment are reported. Comparison of post-flight current-voltage characteristics with similar pre-flight data revealed little or no change in solar cell conversion efficiency, confirming the reliability and endurance of space photovoltaic cells. This finding is in agreement with the lack of significant physical changes in the solar cells despite nearly six years in the low Earth orbit environment.

Description: Discussions of the multi-band gap (MBG) and new solar cell options workshop are presented. Topics discussed include: greater than 2 terminal cells; radiation damage preventing development of MBG cells for space; lattice matching; measurement of true performance; future of II-VI materials in MBG devices; and quaternaries.

Description: The workshop on new silicon cells held during SPRAT12 is summarized. A smaller than average group attended this workshop reflecting the reduction in research dollars available to this portion of the photovoltaics community. Despite the maturity of the silicon technology, a core of the group maintained an excitement about new developments and potential opportunities. The group addressed both the implications and the applications of recent developments. Topics discussed include: light trapping and ultrathin silicon cells; different uses for silicon cells; new silicon cell developments; and radiation tolerant high efficiency cells.

Description: A summation of responses to questions posed to the thin-film solar cell workshop and the ensuing discussion is provided. Participants in the workshop included photovoltaic manufacturers (both thin film and crystalline), cell performance investigators, and consumers.

Description: The results for the first year in orbit of the DRA solar cell experiment flying on the Surrey University UoSAT-5 satellite are described. Several problems were identified with the measured data, which are discussed along with the techniques used to remove or minimize the effect of the problems. After 1 year in orbit the majority of the cells flying on the experiment have undergone little or no degradation. The exception to this are all the ITO/InP cells, supplied by two different manufacturers, they are showing more degradation than the GaAs cells. This result is unexpected and currently unexplainable. It will be necessary to retrieve data from the experiment for several years to obtain the best results due to the relatively benign radiation environment.

Description: Short-circuit current degradation of electron irradiated double-layer antireflective-coated cells after 3000 hours ultraviolet (UV) exposure exceeds 3 percent; extrapolation of the data to 10(exp 5) hours (11.4 yrs.) gives a degradation that exceeds 10 percent. Significant qualitative and quantitative differences in degradation were observed in cells with double- and single-layer antireflective coatings. The effects of UV-source age were observed and corrections were made to the data. An additional degradation mechanism was identified that occurs only in previously electron-irradiated solar cells since identical unirradiated cells degrade to only 6 +/- 3 percent when extrapolated 10(exp 5) hours of UV illumination.

Description: Current satellite algorithms to estimate photosynthetically available radiation (PAR) at the earth' s surface are reviewed. PAR is deduced either from an insolation estimate or obtained directly from top-of-atmosphere solar radiances. The characteristics of both approaches are contrasted and typical results are presented. The inaccuracies reported, about 10 percent and 6 percent on daily and monthly time scales, respectively, are useful to model oceanic and terrestrial primary productivity. At those time scales variability due to clouds in the ratio of PAR and insolation is reduced, making it possible to deduce PAR directly from insolation climatologies (satellite or other) that are currently available or being produced. Improvements, however, are needed in conditions of broken cloudiness and over ice/snow. If not addressed properly, calibration/validation issues may prevent quantitative use of the PAR estimates in studies of climatic change. The prospects are good for an accurate, long-term climatology of PAR over the globe.

Description: Imaging spectrometers have many potential applications in the environmental sciences. One of the more promising applications is that of estimating the biochemical concentrations of key foliar biochemicals in forest canopies. These estimates are based on spectroscopic theory developed in agriculture and could be used to provide the spatial inputs necessary for the modeling of forest ecosystem dynamics and productivity. Several foliar biochemicals are currently under investigation ranging from those with primary absorption features in visible to middle infrared wavelengths (e.g., water, chlorophyll) to those with secondary to tertiary absorption features in this part of the spectrum (e.g., nitrogen, lignin). The foliar chemical of interest in this paper is chlorophyll; this is a photoreceptor and catalyst for the conversion of sunlight into chemical energy and as such plays a vital role in the photochemical synthesis of carbohydrates in plants. The aim of the research reported here was to determine if the chlorophyll concentration of a forest canopy could be correlated with the reflectance spectra recorded by the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS).

Description: In June 1991, the NASA/Jet Propulsion Laboratory airborne synthetic-aperture radar (AIRSAR) instrument collected the first calibrated data set of multifrequency, polarimetric, radar observations of the Greenland ice sheet. At the time of the AIRSAR overflight, ground teams recorded the snow and firn (old snow) stratigraphy, grain size, density, and temperature at ice camps in three of the four snow zones identified by glaciologists to characterize four different degrees of summer melting of the Greenland ice sheet. The four snow zones are: (1) the dry-snow zone, at high elevation, where melting rarely occurs; (2) the percolation zone, where summer melting generates water that percolates down through the cold, porous, dry snow and then refreezes in place to form massive layers and pipes of solid ice; (3) the soaked-snow zone where melting saturates the snow with liquid water and forms standing lakes; and (4) the ablation zone, at the lowest elevations, where melting is vigorous enough to remove the seasonal snow cover and ablate the glacier ice. There is interest in mapping the spatial extent and temporal variability of these different snow zones repeatedly by using remote sensing techniques. The objectives of the 1991 experiment were to study changes in radar scattering properties across the different melting zones of the Greenland ice sheet, and relate the radar properties of the ice sheet to the snow and firn physical properties via relevant scattering mechanisms. Here, we present an analysis of the unusual radar echoes measured from the percolation zone.

Description: We are comparing three methods of mapping analysis tools for imaging spectroscopy data. The purpose of this comparison is to understand the advantages and disadvantages of each algorithm so others would be better able to choose the best algorithm or combinations of algorithms for a particular problem. The three algorithms are: (1) the spectralfeature modified least squares mapping algorithm of Clark et al (1990, 1991): programs mbandmap and tricorder; (2) the Spectral Angle Mapper Algorithm(Boardman, 1993) found in the CU CSES SIPS package; and (3) the Expert System of Kruse et al. (1993). The comparison uses a ground-calibrated 1990 AVIRIS scene of 400 by 410 pixels over Cuprite, Nevada. Along with the test data set is a spectral library of 38 minerals. Each algorithm is tested with the same AVIRIS data set and spectral library. Field work has confirmed the presence of many of these minerals in the AVIRIS scene (Swayze et al. 1992).

Description: Soil moisture content is an important parameter in many disciplines of science like hydrology, meteorology, agriculture and others. Microwave remote sensing technique has a high potential in measuring the dielectric constant of soils, which is strongly governed by the soil moisture. Much excellent work has been done on investigating the relationship between backscattering coefficient and soil moisture. Most of these studies are measured in a laboratory or are carried out with a multitemporal data set. This means, that the variation in the backscattering coefficient is only related to the soil moisture because all other parameters influencing the backscattering like surface roughness, vegetation cover, plant geometry, phenology of plants and row direction are kept constant. In this study the sensitivity of the backscattering coefficient to soil moisture of corn fields is investigated. In the framework of the MAC-Europe Campaign in June 1991, the NASA/JPL three-frequency polarimetric AIRSAR system collected data over the test site Oberpfaffenhofen. The AIRSAR campaign in Oberpfaffenhofen was complemented with intensive ground truth measurements. The sampled corn fields are nearly in the range of the same incidence angle (approximately 20 deg) and belong to different soil types. The evaluation was carried out at a single data set. The results show that the backscattering, measured at P-band, can be described with only two parameters very well. The main parameter influencing the backscattering is the soil moisture content; the second subordinated parameter is the row direction.

Description: As part of research on forest ecosystems, the Jet Propulsion Laboratory (JPL) and collaborating research teams have conducted multi-season airborne synthetic aperture radar (AIRSAR) experiments in three forest ecosystems including temperate pine forest (Duke, Forest, North Carolina), boreal forest (Bonanza Creek Experimental Forest, Alaska), and northern mixed hardwood-conifer forest (Michigan Biological Station, Michigan). The major research goals were to improve understanding of the relationships between radar backscatter and phenological variables (e.g. stand density, tree size, etc.), to improve radar backscatter models of tree canopy properties, and to develop a radar-based scheme for monitoring forest phenological changes. In September 1989, AIRSAR backscatter data were acquired over the Duke Forest. As the aboveground biomass of the loblolly pine forest stands at Duke Forest increased, the SAR backscatter at C-, L-, and P-bands increased and saturated at different biomass levels for the C-band, L-band, and P-band data. We only use the P-band backscatter data and ground measurements here to study the relationships between the backscatter and stand density, the backscatter and mean trunk dbh (diameter at breast height) of trees in the stands, and the backscatter and stand basal area.

Description: During the Mac-Europe campaign of 1991 several SAR (Synthetic Aperature Radar) experiments were carried out in the Flevoland test area in the Netherlands. The test site consists of a forested and an agricultural area with more than 15 different crop types. The experiments took place in June and July (mid to late growing season). The area was monitored by the spaceborne C-band VV polarized ERS-1, the Dutch airborne PHARS with similar frequency and polarization and the three-frequency PP-, L-, and C-band) polarimetric AIRSAR system of NASA/JPL. The last system passed over on June 15, 3, 12, and 28. The last two dates coincided with the overpasses of the PHARS and the ERS-1. Comparison of the results showed that backscattering coefficients from the three systems agree quite well. In this paper we present the results of a study of crop type classification (section 2) and soil moisture determination in the agricultural area (section 3). For these studies we used field averaged Stokes matrices extracted from the AIRSAR data (processor version 3.55 or 3.56).

Description: In preparation for the launch of SIR-C/X-SAR and design studies for future orbital SAR, a program has made considerable progress in the development of an SAR terrain classifier and algorithms for quantification of biophysical attributes. The goal of this program is to produce a generalized software package for terrain classification and estimation of biophysical attributes and to make this package available to the larger scientific community. The basic elements of the SAR (Synthetic Aperture Radar) terrain classifier are outlined. An SAR image is calibrated with respect to known system and processor gains and external targets (if available). A Level 1 classifier operates on the data to differentiate: urban features, surfaces and tall and short vegetation. Level 2 classifiers further subdivide these classes on the basis of structure. Finally, biophysical and geophysical inversions are applied to each class to estimate attributes of interest. The process used to develop the classifiers and inversions is shown. Radar scattering models developed from theory and from empirical data obtained by truck-mounted polarimeters and the JPL AirSAR are validated. The validated models are used in sensitivity studies to understand the roles of various scattering sources (i.e., surface trunk, branches, etc.) in determining net backscatter. Model simulations of sigma (sup o) as functions of the wave parameters (lambda, polarization and angle of incidence) and the geophysical and biophysical attributes are used to develop robust classifiers. The classifiers are validated using available AirSAR data sets. Specific estimators are developed for each class on the basis of the scattering models and empirical data sets. The candidate algorithms are tested with the AirSAR data sets. The attributes of interest include: total above ground biomass, woody biomass, soil moisture and soil roughness.

Description: The ability of remote sensing for monitoring vegetation density and soil moisture for agricultural applications is extensively studied. In optical bands, vegetation indices (NDVI, WDVI) in visible and near infrared reflectances are related to biophysical quantities as the leaf area index, the biomass. In active microwave bands, the quantitative assessment of crop parameters and soil moisture over agricultural areas by radar multiconfiguration algorithms remains prospective. Furthermore the main results are mostly validated on small test sites, but have still to be demonstrated in an operational way at a regional scale. In this study, a large data set of radar backscattering has been achieved at a regional scale on a French pilot watershed, the Orgeval, along two growing seasons in 1988 and 1989 (mainly wheat and corn). The radar backscattering was provided by the airborne scatterometer ERASME, designed at CRPE, (C and X bands and HH and VV polarizations). Empirical relationships to estimate water crop and soil moisture over wheat in CHH band under actual field conditions and at a watershed scale are investigated. Therefore, the algorithms developed in CHH band are applied for mapping the surface conditions over wheat fields using the AIRSAR and TMS images collected during the MAC EUROPE 1991 experiment. The synergy between optical and microwave bands is analyzed.

Description: Synthetic Aperture Radar (SAR) images acquired from various sources such as Shuttle Imaging Radar B (SIR-B) and airborne SAR (AIRSAR) have been analyzed for signatures of soil moisture. The SIR-B measurements have shown a strong correlation between measurements of surface soil moisture (0-5 cm) and the radar backscattering coefficient sigma(sup o). The AIRSAR measurements, however, indicated a lower sensitivity. In this study, an attempt has been made to investigate the causes for this reduced sensitivity.

Description: The interaction of climate and topography in mountainous regions is dramatically expressed in the spatial distribution of glaciers and snowcover. Monitoring existing alpine glaciers and snow extent provides insight into the present mountain climate system and how it is changing, while mapping the positions of former glaciers as recorded in landforms such as cirques and moraines provide a record of the large past climate change associated with the last glacial maximum. The Andes are an ideal mountain range in which to study the response of snow and ice to past and present climate change. Their expansive latitudinal extent offers the opportunity to study glaciers in diverse climate settings from the tropical glaciers of Peru and Bolivia to the ice caps and tide-water glaciers of sub-polar Patagonia. SAR has advantages over traditional passive remote sensing instruments for monitoring present snow and ice and differentiating moraine relative ages. The cloud penetrating ability of SAR is indispensable for perennially cloud covered mountains. Snow and ice facies can be distinguished from SAR's response to surface roughness, liquid water content and grain size distribution. The combination of SAR with a coregestered high-resolution DEM (TOPSAR) provides a promising tool for measuring glacier change in three dimensions, thus allowing ice volume change to be measured directly. The change in moraine surface roughness over time enables SAR to differentiate older from younger moraines. Polarimetric SAR data have been used to distinguish snow and ice facies and relatively date moraines. However, both algorithms are still experimental and require ground truth verification. We plan to extend the SAR classification of snow and ice facies and moraine age beyond the ground truth sites to throughout the Cordillera Real to provide a regional view of past and present snow and ice. The high resolution DEM will enhance the SAR moraine dating technique by discriminating relative ages based on moraine slope degradation.