ALBERT

Description: As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Description: The key measurement to acquire for understanding unsteady flow is surface pressure. Unsteady Pressure-Sensitive Paint (uPSP) is an emerging optical technique used in wind tunnel testing to measure fluctuating surface pressures. Recently, tests were conducted on NASAs Space Launch System in NASA Ames Research Centers Unitary Plan Wind Tunnel to determine the aeroacoustics environment and assist in developing the buffet forcing functions. Unsteady PSP data was collected during this test campaign. Steady state PSP data, infrared thermography, shadowgraph, accelerometer data, and dynamic pressure transducer data were also collected. In all 50 TB of data were collected during the three days of testing. During these three days of testing, a repeating transonic and supersonic alpha sweep condition was acquired. This paper presents these two wind tunnel conditions and examines how the temperature influences the PSP data. In the first large demonstration of uPSP in 2015 on an NESC-, AETC-sponsored wind tunnel test, lifetime PSP results highlighted the influence the model temperature had on the PSP data. A best practice of heat soaking the model before acquiring calibration images was followed during the test campaign presented in this paper. An infrared thermography camera and thermocouples were installed in the model to collect more details of the model surface temperature. Data processing schemes for uPSP are still in development but will be briefly presented here as well.

Description: Progress in aerodynamics over the past 50 years has been evidenced by the development of increasingly sophisticated and efficient flight vehicles throughout the flight spectrum. Advances have generally arisen in an evolutionary manner from experience gained in wind tunnel testing, flight testing, and improvements in analytical and computational capabilities. As a result of this evolutionary development, both military and commercial vehicles operate at a relatively high efficiency level. This observation plus the fact that airplanes have not changed appreciably in outward appearance over recent years has led some skeptics to conclude incorrectly that aerodynamics is a mature technology, with little to be gained from further developments in the field. It is of interest to note that progress in aerodynamics has occurred without a thorough understanding of the fundamental physics of flow, turbulence, vortex dynamics, and separated flow, for example. The present understanding of transition, turbulence, and boundary layer separation is actually very limited. However, these fundamental flow phenomena provide the key to reducing the viscous drag of aircraft. Drag reduction provides the greatest potential for increased flight efficiency from the standpoint of both saving energy and maximizing performance. Recent advances have led to innovative concepts for reducing turbulent friction drag by modifying the turbulent structure within the boundary layer. Further advances in this basic area should lead to methods for reducing skin friction drag significantly. The current challenges for military aircraft open entirely new fields of investigation for the aerodynamicist. The ability through very high speed information processing technology to totally integrate the flight and propulsion controls can permit an aircraft to fly with "complete abandon," avoiding departure, buffet, and other undesirable characteristics. To utilize these new control concepts, complex aerodynamic phenomena will have to be understood, predicted, and controlled. Current requirements for military aircraft include configuration optimization through a widened envelope from subsonic to supersonic and from low to high angles of attack. This task is further complicated by requirements for control of observables. These challenging new designs do not have the luxury of a large experimental data base from which to optimize for various parameter combinations. Consequently, there exists a strong need for better techniques, both experimental and computational, to permit design optimization in a complete sense.

Description: The effects of long term exposure to the near Earth space environment on advanced electrooptical and radiation sensor components were examined. The effect of long duration spaceflight on the germination rate of selected terrestrial plant seeds is observed in exobiological experiments.

Description: The 587B series of protectors are unique, low clamping voltage transient suppressors to protect ac-powered equipment from the 6000V peak open-circuit voltage and 3000A short circuit current as defined in IEEE standard 587 for Category B transients. The devices, which incorporate multiple-stage solid-state protector components, were specifically designed to operate under multiple exposures to maximum threat levels in this severe environment. The output voltage peaks are limited to 350V under maximum threat conditions for a 120V ac power line, thus providing adequate protection to vulnerable electronic equipment. The principle of operation and test performance data is discussed.

Description: A description of the structure and uses of the Long Duration Exposure Facility (LDEF) is given. The LDEF was designed to provide a large number of economical opportunities for science and technology experiments that require modest electrical power and data processing while in space and which benefit from postflight laboratory investigations with the retrieved experiment hardware. Like the Shuttle, the LDEF is reusable, and repeat missions are planned, each with a new complement of experiments. The LDEF is essentially a free-flying cylindrical structure. The experiments on LDEF are totally self-contained in trays mounted on the exterior of the structure. LDEF can accommodate 86 experiment trays, 72 around the circumference and 14 on the two ends. The LDEF is delivered to Earth orbit by the Shuttle. In orbit, the Shuttle remote manipulator system removes the LDEF from the Shuttle payload bay and places it in a gravity-gradient-stabilized attitude. After an extended period in orbit, which is set by experiment requirements, the LDEF is retrieved on a subsequent Shuttle flight.

Description: In this paper, the linearized relativistic Vlasov equation is solved and a dispersion relation is calculated for the interaction between a relativistic electron beam and the electromagnetic fields of a rectangular waveguide supporting TE(mn) modes. The dispersion relation is simplified to the special case of a frame of reference moving with the electrons and the resulting coupling coefficient epsilon(mn)super l is calculated for various TE(mn) modes. The dependence of epsilon(mn)super l on the parity of the harmonic number l and various mn modes of the waveguide are discussed.

Description: Various operational aspects of the Spacelab 1 mission are reviewed by the four payload crew members. Two-shift operations, voice communication with ground investigators, joint participation in experiment activity, Spacelab performance, and recent advances are discussed.

Description: Double-drift GaAs IMPATT diodes were designed for V-band frequency operations and fabricated using molecular-beam epitaxy. The diodes were fabricated in two configurations: (1) circular mesa diodes with silver-plated (integrated) heat sinks: (2) pill-type diodes bonded to diamond heat sinks. Both configurations utilized a miniature quartz-ring package. Output power greater than 1 W CW was achieved at V-band frequencies from diodes on diamond heat sinks. The best conversion efficiency was 13.3 percent at 55.5 GHz with 1 W output power.

Description: State-of-the-art performance is demonstrated with solid-state amplifiers in K-band. The amplifier provides 8.2 watts of power with 39 dB gain over a frequency band of 1.4 GHz. Nonlinearity analyses of solid-state amplifiers suggest that system performance can be improved significantly by using an FET amplifier. Preliminary investigations reveal that the solid-state amplifiers can be space-qualified and can be expected to replace the TWTA in many communication links in the near future. It is pointed out that with improvements in device technology, the power, bandwidth and efficiency of solid-state amplifiers using FETs can be further improved. With FETs operating at a junction temperature of less than 125 C, solid-state amplifiers are inherently reliable, indicating a ten-year mean time to failure.

Description: The accuracy of high-speed wafer-level measurements on digital IC's is limited by the probe interface. This limitation strongly encourages the use of built-in on-chip test hardware to reduce the number of critical off-chip high-speed interfaces. A novel synchronous propagation delay test structure is described which will provide accurate parametric data under typical automatic test conditions. Built-in test features added to complex combinational circuits are shown which are useful for delay measurement and which reduce the total number of high-speed I/O connections while still providing acceptable fault coverage in many cases.

Description: Basic theoretical and experimental characteristics of a novel 'Thin-MOS' technology, which has promising aspects for integrated high-frequency devices up to several hundred gigahertz are presented. The operation of such devices depends on charge injection into undoped silicon layers of about 1000-A thickness, grown by molecular beam epitaxy on heavily doped substrates, and isolation by thermally grown oxides of about 100-A thickness. Capacitance-voltage characteristics measured at high and low frequencies agree well with theoretical ones derived from uni and ambipolar space-charge models. It is concluded that after oxidation the residual doping in the epilayer is less than approximately 10 to the 16th/cu cm and rises by 3 orders of magnitude at the substrate interface within less than 100 A and that interface states at the oxide interface can be kept low.

Description: A model for dendritic growth in a binary alloy melt, in the presence of a positive temperature gradient in the liquid, is presented. The model describes satisfactorily the transition from a dendritic interface to a planar interface at very low and very large growth rates. A dendrite tip stability parameter is derived, strictly from steady state considerations, without resorting to a perturbation analysis. The estimates of the parameter agree with those obtained by models based on perturbation analyses.

Description: It is shown that stoichiometry variations in the GaAs melt during growth constitute the most critical parameter regarding defect formations and their interactions; this defect structure determines all relevant characteristics of GaAs. Convection in the melt leads to stoichiometric variations. Growth in axial magnetic fields reduces convection and permits the study of defect structure. In order to control stoichiometry in space and to accommodate expansion during solidification, a partially confined configuration was developed. A triangular prism is employed to contain the growth melt. This configuration permits the presence of the desired vapor phase in contact with the melt for controlling the melt stoichiometry.

Description: Two methods are described to obtain the value of the series resistance (R) of a Schottky diode from its forward I-V characteristic. The value of R is then used to plot the curve ln(I) versus V sub D (= V - IR) which becomes a straight line even if ln(I) versus V does not. The ideality factor n and the Schottky-barrier height of the diode then follow from the standard procedure. The main advantages of the methods are: (1) a linear regression can be used to calculate the value of R; (2) many data points are used over the whole data range, which raises the accuracy of the results, and (3) the validity of constant R assumption can be checked by the linearity of the ln (I) versus V sub D curve. The methods are illustrated on the experimental data of a real diode.

Description: An electromagnetic furnace is being prepared for flights aboard the Space Shuttle. This apparatus is capable of melting metals and alloys up to 1400 C melting point by induction heating with subsequent solidification of the freely levitated melt without contact with any container. The solidification can be carried out with greatly reduced fields resulting in minimal heating and stirring of the free melt. Sequential specimens can be processed during flight. Several experiments are planned for a series of flights, beginning in 1985 with an undercooling experiment of NiSn alloys. These will be interspersed with detailed studies of fluid flow caused by low and high field levels in order to quantify the corresponding effect upon the solidification process.

Description: Enhanced electron trapping has been observed in n-channels of rad-hard CMOS devices due to electron and gamma-ray irradiation. Room-temperature annealing results in a positive shift in the threshold potential far beyond its initial value. The slope of the annealing curve immediately after irradiation was found to depend strongly on the gate bias applied during irradiation. Some dependence was also observed on the electron dose rate. No clear dependence on energy and shielding over a delidded device was observed. The threshold shift is probably due to electron trapping at the radiation-induced interface states and tunneling of electrons through the oxide-silicon energy barrier to fill the radiation-induced electron traps. A mathematical analysis, based on two parallel annealing kinetics, hole annealing and electron trapping, is applied to the data for various electron dose rates.

Description: The ionizing radiation responses of metal oxide semiconductor (MOS) field-effect transistors (FETs) and MOS capacitors are compared. It is shown that the radiation-induced threshold voltage shift correlates closely with the shift in the MOS capacitor inversion voltage. The radiation-induced interface-state density of the MOSFETs and MOS capacitors was determined by several techniques. It is shown that the presence of 'slow' states can interfere with the interface-state measurements.

Description: Three read/write random access memories, AM91L24, HM1-6514, and MWS 5114, were subjected to total dose irradiation at three dose rates, with electrical testing after each increment of dosage. Annealing measurements were performed after the radiation tests were completed. The AM91L24 showed a strong dose rate effect and substantial post-irradiation annealing of radiation-induced damage. The dose rate effect was that a lower dose rate produced less net damage than an eqivalent total dose applied at a higher rate. The HM1-6514 showed essentially no dose rate effect and no annealing damage, and the MWS 5114 exhibited a moderate effect with some annealing. It was concluded that dose rate is an important parameter in radiation test procedures for MOS microcircuits and that annealing measurements may be important evaluation aids for such tests.

Description: This paper examines bipolar junction transistor models suitable for calculating the effects of large excursions of some of the variables determining the operation of a transistor. Both the Ebers-Moll and Gummel-Poon models are studied, and the junction and diffusion capacitances are evaluated on the basis of the latter model. The most interesting result of this analysis is that a bipolar junction transistor when struck by a cosmic particle may cause a single event upset in an electronic circuit if the transistor is operated at a low forward base-emitter bias.

Description: A magnetically-collimated, double-pulsed electron gun capable of generating electron pulses with a peak instantaneous current of approximately 70 microamps and a temporal width of 0.35 ns (FWHM) has been developed. Calibration is accomplished by measuring the lifetime of the well known 2(1P)-to-1(1S) transition in helium (58.4nm) at a near-threshold electron-impact energy by use of the delayed-coincidence technique.

Description: The instrumentation, trajectory, and missions of the ISEE-3 spacecraft being sent to observe Comet Giacobini-Zimmer (GZ) are described. Originally parked at a libration point to observe the solar wind, ISEE-3 was directed to perform a complex series of flybys of the earth and the moon to move to a trajectory that will intersect the GZ tail in 1985. Renamed ICE, the spacecraft will record magnetic field and charged particle data on the interaction of the cometary tail with the solar wind.

Description: The effect of cooling as a fundamental limit to delay times in IC's was considered. It appears that the delay time should be decreased at cryogenic temperatures.

Description: Recent findings drawn from various laboratories focused toward a new understanding of the nature of crystal growth and how impurities are incorporated or excluded from the lattice were considered. From these findings a heuristic approach is given for improving the uniformity and charge carrier concentration of thin semiconductor films. Such improvement is considered essential to achieve respectable yield on large scale integrated circuits. A tentative conclusion is drawn which indicates that if the host compound crystal reactants are provided to the growing crystal surface in a reasonably stoichiometric manner, it is virtually impossible to include impurities into a growing crystal surface held at a sufficiently low temperature; impurities are incorporated into the crystal by gettering action of crystal defects located one and two monlayers beneath the growing surface. Devices in 3-5 semiconductors based on heterojunctions and two dimensional electron gases are noted and reliability concerns are voiced. Alternatives and novel device structures such as truly single crystal high quality silicon on insulator and beta silicon carbide devices are presented.

Description: Generally speaking, several roles are seen for low temperatures in electronics: As a means of extracting better performance from existing technology, avoiding expense and delay required for the advances in design or fabrication which would be needed to achieve the same performance at room temperature. As a necessity in the quest for improved performance, to counteract detrimental effects which arises as technology is pushed to extremes. As an opportunity to take advantage of effects made available by low temperature operation, and to develop new devices based on them. The electronic devices and circuits considered are those based on semiconductivity. Superconductive devices and circuits are not included.

Description: A general criterion is derived for the stability of a negative-resistance oscillator with respect to small perturbations in the operating point. The derivation applies when the oscillator output consists of an arbitrary number of related frequency components, including possible nonharmonic components. Examples are given of the application of the stability criterion to coaxial IMPATT oscillator circuits, with experimental verification of the frequency and output power at theoretically determined stable operating points.

Description: The paper reviews the progress made in manned and unmanned space programs during the last 25 years and names several major accomplishments. The ingredients of success are identified as good engineering, good technology, and good management of a very complex enterprise. An argument is made that the pace of progress will be governed not by technological advances, which can be very rapid, but rather by future institutional arrangements, which are much slower to evolve. It is predicted that the most likely space activities for the next 20 years will be those relating to space commercialization, and several examples are cited. A hope is expressed that policy makers and entrepreneurs will match the spirit of adventure and risk-taking exhibited by engineers in exploring uncharted territory.

Description: The NASA manned space station will consist of three main elements: habitable modules, solar collectors, and their interconnecting hardware. The most arduous of the requirements to be met by this configuration is the simultaneous integration of terrestrial, solar, and celestial viewing instruments, since omnidirectional simultaneous viewing is made difficult by the station's large solar energy collection devices. The space station also imposes unique design conditions on individual subsystems, such as the power distribution and energy storage hardware. In particular, the thermal control subsystem must be designed to meet a variety of mission, payload, and housekeeping tasks that demand a large heat rejection capacity. Novel environmental control and life support subsystem technology will be indispensable.

Description: Radio astronomers have investigated spatial frequencies and their relationship to apertures with the objective to improve the resolution in radio observations. Welch (1965) has related Fourier transform theory developed for linear communications to aperture design problems, while Fakley (1959) has conducted a comparison between the performances of a time-averaged product array and an intraclass correlator. The present investigation is concerned with an approach which resembles very closely the intraclass correlator system considered by Fakley. A description is presented of a process whereby a thinned array of elements samples selected spatial frequencies from a uniform signal wave front incident on the array. The spatial frequencies are used to generate a set of synthetic spatial frequencies which behave as though they had been sampled by a fully filled array. Beam formation is obtained by summing the set of synthetic spatial frequencies.

Description: Recent progress in the development of high-power 60 GHz GaAs IMPATT diodes for communication links with high-data-rate satellites is discussed. One of the advantages of GaAs over Si as the material for the diodes are that GaAs is likely to have a higher output and efficiency than Si despite recent advances in Si technology. It is therefore in GaAs technology that research is currently concentrating. Some of the design strategies of the various companies working on the technology are described, including a pill process, MOCVD growth, and the use of diethy zinc as a dopant. Reliability testing of the diodes will be performed by NASA. Some of the alternatives to solid state amplifiers are discussed, including optical and traveling wave tube technology (TWT).

Description: A tribology experiment in zero gravity was performed during the orbital flight of Spacelab 1 to study the motion of liquid lubricants over solid surfaces. The absence of a significant gravitational force facilitates studies of the motion of liquid lubricants over solid surfaces as controlled by interfacial and capillary forces. Observations were made of phenomena associated with the liquid on one solid surface and also with the liquid between a pair of closely spaced surfaces. Typical photographic records obtained on Spacelab 1 are described.

Description: The Spacelab 1 mission took place during the period Nov. 28 through Dec. 8, 1983. An overview of the first flight of the orbiting laboratory is presented.

Description: It is shown how a simple integrating amplifier based on commercially available JFET and MOSFET switches can be used to measure photocurrents from detectors with noise levels as low as 1.6 x 10 to the -18th A/root Hz (10 electrons/sec). A figure shows the basic circuit, along with the waveform at the output. The readout is completely nondestructive; the reset noise does not contribute since sampling of the accumulated charge occurs between resets which are required only when the stored charge has reached a very high level. The storage capacity ranges from 10 to the 6th to 10 to the 9th electrons, depending on detector parameters and linearity requirements. Data taken with an Si:Sb detector operated at 24 microns are presented. The responsivity agrees well with the value obtained by Young et al. (1981) in the transimpedance amplifier circuit. The data are seen as indicating that extremely low values of NEP can be obtained for integration times of 1 sec and that longer integrations continue to improve the SNR at a rate faster than the square root of time when background noise is not present.

Description: The Model SP-320 device is a monolithic realization of a complex general purpose signal processor, incorporating such features as a 32-bit ALU, a 16-bit x 16-bit combinatorial multiplier, and a 16-bit barrel shifter. The SP-320 is designed to operate as a slave processor to a host general purpose computer in applications such as coherent integration of a radar return signal in multiple ranges, or dedicated FFT processing. Presently available is an I/O module conforming to the Intel Multichannel interface standard; other I/O modules will be designed to meet specific user requirements. The main processor board includes input and output FIFO (First In First Out) memories, both with depths of 4096 W, to permit asynchronous operation between the source of data and the host computer. This design permits burst data rates in excess of 5 MW/s.

Description: A set of code sequences is a complementary code sequence set if the sum of the aperiodic autocorrelation functions for the sequences is zero everywhere except at the origin. A simple construction for sets of complementary code sequences is discussed.

Description: The rubidium-crystal oscillator hybrid (RbXO) will make precise time available to systems that lack the power required by atomic frequency standards. The RbXO consists of two subassemblies in separate enclosures. One contains a small rubidium frequency standard (RFS) without its internal oven-controlled crystal oscillator (OCXO), plus interface circuits. The second contains a low-power OCXO, and additional interface circuits. The OCXO is on continuously. Periodically, e.g., once a week, the user system applies power to the RFS. After the few necessary for the warmup of the RFS, the interface circuits adjust the frequency of the OCXO to the RFS reference, then shut off the RFS. The OCXO enclosure is separable from the RFS enclosure so that manpacks will be able to operate with minimum size, weight, and power consumption, while having the accuracy of the RFS for the duration of a mission. A prototype RbXO's RFS has operated successfully for 4200 on-off cycles. Parallel efforts on a Phase 2 RbXO development are in progress. Two sources for the RbXO are scheduled to be available during 1986.

Description: Space based servicing of an orbit transfer vehicle (OTV) was previously outlined in sufficient detail to arrive at OTV and support system servicing requirements. Needed space station facilities and their functional requirements were identified. The impact of logistics and space serviceable design on the OTV design is detailed herein. RL10 derivative rocket engine inspection task times are enumerated.

Description: A spacecraft electric power supply system is described. Requirements of the system are to accelerate a momentum wheel to a fixed maximum speed when solar energy is available and to maintain a constant voltage on the spacecraft bus under varying loads when solar energy is not available. Candidate motor types, pulse width modulated current control systems, and efficiency considerations are discussed. In addition, the Lunar Roving Vehicle motors are described along with their respective efficiencies.

Description: The use of the F-104 Interceptor for low gravity materials processing experiments is extended to include alloy solidification studies above 1000 C. The F-104 can provide up to 60 seconds of low gravity, but requires a unique experiment package for integration into the aircraft, both physically and electronically. The current research with the F-104 experimental furnace system which has been used to process cast iron samples is described. Results demonstrate the capability of the facility and its operation.

Description: By following a single hypothetical example through a series of variations, the way different potential investors might look at the opportunity to participate in space commercialization is described. The example itself is fairly typical of commercial opportunities in space. The chief characteristics are a steadily increasing requirement for capital infusion over an 8 year period, followed by a very generous stream of profits running another decade or more beyond. There is a decision point at 3 years, at the conclusion of laboratory R&D; and another at 6 years, following 2 initial space flights.

Description: Key milestones necessary to establish the transfer orbit stage are examined. The selection of the project concept and synthesis of the company are described followed by an analysis venture capability support and the selection of a major aerospace company as prime contractor. A landmark agreement with NASA sanctioned the commercial TOS concept and provided the critical support necessary to raise the next round of venture capital. Project management and customer commitments are also discussed.

Description: Preliminary results for the Critical Point Wetting CPW Drop Tower Experiment are produced with immiscible systems. Much of the observed phenomena conformed to the anticipated behavior. More drops will be needed to test the CPW theory with these immiscible systems.

Description: The use of low gravity in the development of new products is examined. Low gravity fundaments are presented clearly and simply. A display of past low gravity experiments highlights some of these precepts which are followed by a description of where and how the commercial user can fly his experiment or process.

Description: A technique which is particularly suited to microgravity environments and which is potentially more powerful than electrophoresis is phase partitioning. Phase partitioning is purification by partitioning between the two immiscible aqueous layers formed by solution of the polymers poly(ethylene glycol) and dextran in water. This technique proved to be very useful for separations in one-g but is limited for cells because the cells are more dense than the phase solutions thus tend to sediment to the bottom of the container before reaching equilibrium with the preferred phase. There are three phases to work in this area: synthesis of new polymers for affinity phase partitioning; development of automated apparatus for ground-based separations; and design of apparatus for performing simple phase partitioning space experiments, including examination of mechanisms for separating phases in the absence of gravity.

Description: PROJECT EXPLORER is a program that will fly student-developed experiments onboard the Space Shuttle in NASA's Get-Away Special (GAS) containers. The program is co-sponsored by the Alabama Space and Rocket Center, the Alabama-Mississippi Section of the American Institute of Aeronautics and Astronautics, Alabama A&M University and requires extensive support by the University of Alabama in Huntsville. A unique feature of this project will demonstrate transmissions to ground stations on amateur radio frequencies in English language. Experiments Nos. 1, 2, and 3 use the microgravity of space flight to study the solidification of lead-antimony and aluminum-copper alloys, the growth of potassium-tetracyanoplatinate hydrate crystals in an aqueous solution, and the germination of radish seeds. Flight results will be compared with Earth-based data. Experiment No. 4 features radio transmission and will also provide timing for the start of all other experiments. A microprocessor will obtain real-time data from all experiments as well as temperature and pressure measurements taken inside the canister. These data will be transmitted on previously announced amateur radio frequencies after they have been converted into the English language by a digitalker for general reception.

Description: An overview of space service opportunities as identified by a Wyle Laboratories' research team is given. Through the use of a baseline space scenario, a variety of space hardware, services, and commercial activities are identified and related on a time-phased basis. A model is presented to relate the potential functions of government and the private sector in a commercialized space environment during the period 1984 to 2004. Barriers, incentives and key issues are likewise identified and addressed to aid in the implementation of private sector activities for spacerelated programs. Broader awareness, legislative actions, incentive development and benefit analyses are considered in the presentation. The time-phased plan provides a useful planning and management tool, allows broader communication, and supports overall space commercialization program assessment.

Description: Extensive experience in utilizing long drop tubes for studying effects of microgravity on the solidification of alloys was obtained. While some modifications are necessary to improve versatility, the facility proved to be most useful. Both an electron beam furnace and an electromagnetic levitation furnace can be used. The electron beam furnace is used with vacuum environments (0.00001 torr), whereas the levitation furnace is presently used only in inert gas environments (above 100 torr). Experiments are best applied to refractory alloys because of the sensitivity of the detectors now being used to observe solidification. Processing of lower melting point metals and alloys simply cannot be recorded. On the other hand, expected improvements in detector sensitivity will allow experimentation with relatively low melting alloys. In such cases, solidification will occur in flight only if higher inert gas pressure is used (100 to 760 torr) to increase heat loss by convection. Under these conditions microgravity conditions no longer apply. However, as shown by results to date, it is not microgravity as such that is important in drop tube solidification. Instead it is the containerless nature of the process that is significant, leading to large degrees of undercooling before solidification and therefore to unique alloys.

Description: The first Nickel Hydrogen battery deployment onboard a commercial geosynchronous communications satellite was realized with the launch of the INTELSAT 5, Flight 6 spacecraft on 19 May 1983. The initial five spacecrafts in this series are equipped with Nickel Cadmium batteries. Based on the data available on both types of batteries, design and operational performance comparisons of INTELSAT 5 Nickel Cadmium batteries are presented. General characteristics of the INTELSAT 5 spacecraft as related to electrical-power-subsystem functions and battery operations are summarized.

Description: The problems and benefits of deep reconditioning to near Earth orbit missions with high cycle life and shallow discharge depth requirements is discussed. A simple battery level approach to deep reconditioning of nickel cadmium batteries in near Earth orbit is considered. A test plan was developed to perform deep reconditioning in direct comparison with an alternative trickle charge approach. The results demonstrate that the deep reconditioning procedure described for near Earth orbit application is inferior to the alternative of trickle charging.

Description: A mathematical model is described which predicts the service life of nickel-cadmium batteries designed for geosynchronous orbit satellites. Regression analysis technique is used to analyze orbital data on second generation trickle charged batteries. The model gives average cell voltage as a function of design parameters, operating parameters and time. The voltage model has the properties of providing a good fit to the data, good predictive capability, and agreement with known battery performance characteristics. Average cell voltage can be predicted to within 0.02 volts for up to 8 years. This modeling shows that these batteries will operate reliably for 10 years. Third-generation batteries are expected to operate even longer.

Description: Although Li/CF cells and batteries have an excellent safety record, they are included with other battery systems that require additional safety precautions. One precaution suggested is the inclusion of shunt diodes into these batteries. The benefits of this addition are examined. All cells tested at elevated temperatures vent regardless of length of time between being fully discharged and reversed or inclusion of the diode in the system. Cells discharged at ambient temperatures all show a relatively quick reversal, but stabilize at voltages that are high enough that the diodes are not functioning. Cells tested at depressed temperatures reverse the deepest of all cells tested, with the deepest reversal occurring very early in the test and voltages recovering to above -0.60 volts near the end of the tests. Anode limited cells will eliminate the venting during hot reversal.

Description: A battery composed of twelve lithium/sulfur dioxide D size cells in series is forced discharged at 21 amperes. This current is established by the proposed use of the battery and represented a discharge condition which might produce venting. Discharge of the battery into voltage reversal results not only in cells venting but also in the violent rupture of at least one cell.

Description: Three lithium batteries proposed as candidates for use in the Global Positioning System are studied. The batteries are discharged at several rates and temperatures both before and after environmental testing. Batteries are heated inside a closed chamber until they vent. Samples of the vented gases are analyzed for components which might be toxic. The test results raise concerns about each of the proposed batteries.

Description: A strong, square cross-section, central column to which experimental and accessory compartments are attached is described. The attachment may be by direct bolting or through vibration and/or thermal isolators, as needed. Structural and thermal characteristics are evaluated.

Description: This autonomous experiment for foaming metals in space involved: (1) payload support structure; (2) furnace and foaming apparatus; (3) electronic controls; (4) battery power; and (5) metallurgy. Emphasis was laid on a modular design which was easily modifiable and which offered maximum durability, safety, and failure tolerance.

Description: The JUFO-1 payload basically consists of the mechanical support structure with two shock isolated mounting shelves for the experiment hardware and the service systems. For the envisaged operation time of 72 hours, three 28 VDC batteries, with a total capacity of approx 1,7 kWh are chosen as a partially redundant power source. Data are acquired by a 12 bit PCM system and stored on a tape recorder. Five experiments were conducted: (1) growth of a liquid KH2PO4 salt solution; (2) manufacturing of nickel catalysts; (3) transport mechanisms of heavy metals in water cress shoots; (4) determining the influence of cosmic radiation on four different plant seeds; and (5) use of a microprocessor-sequencer for payload control and sequencing at a low power consumption.

Description: An experiment to investigate more versatile, lower cost surface tension propellant acquisition approaches for future satellite and spacecraft propellant tanks is designed to demonstrate a propellant off-load capability for a full-tank gallery surface tension device, such as that employed in the shuttle reaction control subsystem, and demonstrate a low-cost refillable trap concept that could be used in future orbit maneuver propulsion systems for multiple engine restarts. A Plexiglas test tank, movie camera and lights, auxiliary liquid accumulator, control electronics, battery pack, and associated valving and plumbing are used. The test liquid is Freon 113, dyed blue for color movie coverage. The fully loaded experiments weighs 106 pounds and is to be installed in a NASA five-cubic-foot flight canister. Vibration tests, acoustic tests, and high and low temperature tests were performed to quality the experiment for flight.

Description: An experiment intended for the space shuttle and designed to investigate the effects of weightlessness and total darkness on gypsy moth eggs and engorged American dog ticks is described. The objectives are: (1) to reevaluate the effects of zero gravity on the termination of diapause/hibernation of embryonated gypsy moth eggs, (2) to determine the effect of zero gravity on the ovipositions and subsequent hatch from engorged female American dog ticks that have been induced to diapause in the laboratory, and (3) to determine whether morphological or biochemical changes occur in the insects under examination. Results will be compared with those from a similar experiment conducted on Skylab 4.

Description: Recommendations submitted for experiments to be conducted onboard the space shuttle are presented. Short biographies of the finalists in the Get Away Special (GAS) competition were included.

Description: Three proposed spaceborne experiments to be conducted by equipment in the Get Away Special (GAS) payload are described. The specific contribution and effect of convection in heat transfer is discussed. Investigations of the surface tension of two liquids in space environment and the problem of liquid slosh in spin stabilized satellites are reviewed.

Description: The positive intrinsic negative (PIN) diode switch which is designed to protect the receiver from burnout or damage on transmission and channel the echo signal to the receiver on reception is outlined. The receiver must be protected firmly. A schematic diagram of a transformer rectifier (TR-ATR) switch for the Urbana Radar is shown. The T/R switch consists of a half wavelength coaxial cavity with tuning condenser and PIN diodes. Two UM4300 PIN diodes were mounted between the inner and outer conductor. The dc biasing voltage required for the PIN diodes is supplied by a control circuit. On transmission, the PIN diodes are forward biased to about 0.5 amperes. On reception, about 10 volts reverse voltage is applied to the diodes, which produces an initial reverse current to speed the recovery time. The T/R switch characteristics are estimated and the result of testing at different peak transmitter powers from 410 kW to 1500 kW is shown.

Description: Space America prepared a private sector land observing space system which includes a sensor system with eight spectral channels configured for stereoscopic data acquisition of four stereo pairs, a spacecraft bus with active three-axis stabilization, a ground station for data acquisition, preprocessing and retransmission. The land observing system is a component of Space America's end-to-end system for Earth resources management, monitoring and exploration. In the context of the Federal Government's program of commercialization of the US land remote sensing program, Space America's space system is characteristic of US industry's use of advanced technology and of commercial, entrepreneurial management. Well before the issuance of the Request for Proposals for Transfer of the United States Land Remote Sensing Program to the Private Sector by the US Department of Commerce, Space Services, Inc., the managing venturer of Space America, used private funds to develop and manage its sub-orbital launch of its Conestoga launch vehicle.

Description: The need for improved purification technologies, the role of electrophoresis, and isoelectric focusing are discussed in the context of space bioprocessing.

Description: A bipolar nickel-hydrogen battery which effectively addresses all key requirements for a spacecraft power system, including long-term reliability and low mass, is discussed. The design of this battery is discussed in the context of system requirements and nickel-hydrogen battery technology in general. To achieve the ultimate goal of an aerospace application of a bipolar Ni-H2 battery several objectives must be met in the design and development of the system. These objectives include: maximization of reliability and life; high specific energy and energy density; reasonable cost of manufacture, test, and integration; and ease in scaling for growth in power requirements. These basic objectives translate into a number of specific design requirements, which are discussed.

Description: In order to develop a long life nickel electrode for a Ni/H2 cell, cycle life tests of nickel electrodes were carried out in Hi/H2 boiler plate cells. A 19 test cell matrix was made of various nickel electrode designs including three levels each of plaque mechanical strength, median pore size of the plaque, and active material loading. Test cells were cycled to the end of their life (0.5v) in a 45-minute low earth orbit cycle regime at 80% depth-of-discharge. The results show that the active material loading level affects the cycle life the most with the optimum loading at 1.6 g/cc void. Mechanical strength did not affect the cycle life noticeably in the bend strength range of 400 to 700 psi. The best plaque type appears to be one which is made of INCO nickel powder type 287 and has a median pore size of 13 micron.

Description: It is noted from the data presented that Li/BCX cells lose approximately 8% of their rated capacity in the first 2 months of storage. After this period of time, little difference is noted in the average realized capacity; however, a significant increase in the range is observed. Over the same period of time the OCV falls at a rate of 0.02V per 1,000 hours. After a period of 8,000 hours the OCV appears stabilize at a value of approximately 3.75V. This may be related to changes in Cl2 concentration due to self-discharge or other reactions. These data indicate that no correlation exists between the reduced open circuit voltage and the realized capacity.

Description: Characterization studies were carried out on a glass fiber paper that is currently employed as a separator material for some LiSOCl2 primary cells. The material is of the non-woven type made from microfilaments of E-type glass and contains an ethyl acrylate binder. Results from extraction studies and tensile testing revealed that the binder content and tensile strength of the paper were significantly less than values specified by the manufacturer. Scanning electron micrographs revealed the presence of clusters of impurities many of which were high in iron content. Results of emission spectroscopy revealed high overall levels of iron and leaching, followed by atomic absorption measurements, revealed that essentially all of this iron is soluble in SOCl2.

Description: Fuel cells have found application in space since Gemini. Over the years technology advances have been factored into the mainstream hardware programs. Performance levels and service lives have been gradually improving. More recently, the storage application for fuel cell-electrolyzer combinations are receiving considerable emphasis. The regenerative system application described here is part of a NASA Fuel Cell Program which was developed to advance the fuel cell and electrolyzer technology required to satisfy the identified power generation and energy storage need of the Agency for space transportation and orbital applications to the year 2000.

Description: Student projects for the Get Away Special (GAS) space shuttle program were summarized. Experimental topics included: seed germination, shrimp growth, liquid lasers, planaria regeneration, fluid dynamics (wicking), soil molds, antibiotics, crystallization, the symbiosis of yeast and fungi, and the performance of electronic chips. A brief experimental design is included for each project.

Description: The Purdue University GAS-1 payload was flown on STS-7. Results of the three experiments included in the payload are summarized. The experiments conducted were: (1) the detection of nuclear particles in near-Earth space environment, (2) an investigation of the effect of microgravity on the germination of sunflower seeds, and (3) an examination of the motion of mercury under low gravity conditions. Results of the payload experiments are discussed from an engineering design standpoint. Data were obtained from one of the experiments, but electrical and mechanical malfunctions prevented the operation of the other two. The thermal control design maintained the desired temperatures and the structure successfully supported all components. The microprocessor collected and stored temperature readings and other data during the flight. A series of recommendations based on these results are included herein.

Description: Snow crystals were grown onboard the space shuttle during STS-7 and STS-8 to facilitate the investigation of crystal growth under conditions of weightlessness. The experimental design and hardware are described. Space-grown snow crystals were polyhedrons looking like spheres, which were unlike snow crystals produced in experiments on Earth.

Description: Three mercury vapor arc lamps were tested in the microgravity environment of one of NASA's small, self-contained payloads during STS-41B. A description of the payload structural design, photographic and optical systems, and electrical system is provided. Thermal control within the payload is discussed. Examination of digital film data indicates that the 175 watt arc lamp has a significant increase in light output when convection is removed in the gravity-free environment of space.

Description: The original slipring design for communications spacecraft, the handling and testing of the slipring assembly before launch, the on orbit performance indicating the need for improvement in dynamic noise, the subsequently incorporated design improvements, and the results of testing to verify noise performance improvement are described.

Description: Interest in high resolution spectrometers for the submillimeter wavelength range from 100 micron to 1,000 micron is mostly stimulated by molecular spectroscopy in radioastronomy and atmospheric physics, and by plasma diagnostic experiments. Schottky diodes in waveguide mixer technology and InSb-hot electron bolometers are successfully used in the 0.5 to a few millimeter range whereas tandem Fabry-Perot spectrometers combined with photoconductive detectors (Ge:Sb and Ge:Ga) are used for the 100 micron range. Recent research on heterodyne spectrometers, with Schottky diodes in an open structure mixer and a molecular laser as local oscillators, which can be used over the whole wavelength range is summarized.

Description: The role of the mission manager in coordinating the payload with the space transportation system is studied. The establishment of the investigators working group to assist in achieving the mission objectives is examined. Analysis of the scientific requirements to assure compatibility with available resources, and analysis of the payload in order to define orbital flight requirements are described. The training of payload specialists, launch site integration, and defining the requirements for the operation of the integrated payload and the payload operations control center are functions of the mission manager. The experiences gained from the management of the Spacelab One Mission, which can be implemented in future missions, are discussed. Examples of material processing, earth observations, and life sciences advances from the First Spacelab Mission are presented.

Description: The scientific experiments package to be carried by the Proteus system takes the form of an Instrument Load carried into orbit by a Space Shuttle, and there mated to a Proteus spacecraft with the Shuttle's Remote Manipulator System. The Proteus system extends to ground support equipment, development tools, and communications, as well as the orbiting satellites. It is expected that Proteus will be able to triple the number of Explorer missions while staying within the current budgetary allocation for such missions. The Proteus spacecraft encompasses a system interface assembly plug, a data handling module, remote interface units, and a power distribution module.

Description: An overview of activities involving the Space Transportation System (STS), now in the operational phase, and results of some of the current space experiments, as well as future research opportunities in microgravity environment, are presented. The experiments of the Materials Processing in Space Program flown on the STS, such as bioseparation processes, isoelectric focusing, solidification and crystal growth processes, containerless processes, and the Materials Experiment Assembly experiments are discussed. Special consideration is given to the experiments to be flown aboard the Spacelab 3 module, the Fluids Experiments System, and the Vapor Crystal Growth System. Ground-based test facilities and planned space research facilities, as well as the nature of the commercialization activities, are briefly explained.

Description: The causes of array faults and efforts to mitigate their effects are examined. Research is concentrated on the panel for the 900 kw second phase of the Sacramento Municipal Utility District (SMUD) project. The panel is designed for hot spot tolerance without comprising efficiency under normal operating conditions. Series/paralleling internal to each module improves tolerance in the power quadrant to cell short or open circuits. Analtyical methods are developed for predicting worst case shade patterns and calculating the resultant cell temperature. Experiments conducted on a prototype panel support the analytical calculations.

Description: Low temperature operation of micron and submicron size Si MOSFETs (metal-oxide-semiconductor field-effect-transistors) results in their improved device characteristics. Various low temperature device properties such as increase in mobility, shift in the theshold voltage, increased reliability, etc., were considered. Other device characteristics such as the subthreshold behavior, delay times and miniaturization at low temperatures are discussed. Discussion includes presenting experimental results along with physical models explaining the observed effects.

Description: Very high performance is being developed in compound semiconductor transistors. High frequency and low noise figure operation in the GaAs FET have already been established. Substantially more performance increases are expected. A comparison of compound semiconductor materials, and their alloys, the physical concepts of high average electron velocity, and the special benefits of modulation doped heterojunction FET devices is presented.

Description: The 20-W S-band power amplifiers aboard the GOES E and F spacecraft exemplify the problems that type-IIa diamond heat sinks have been developed to solve, including the requirement for junction temperatures to be kept below 125 C. Diamond heat sinks allow high power S-band semiconductors to operate at a flange temperature of 70 C without exceeding the stipulated maximum junction temperature. Type-IIA diamond, which is an excellent electrical insulator, possesses a thermal conductivity four times better than pure copper at 100 C, and outperforms BeO by an even greater margin. Higher costs are offset by high reliability. Attention is presently given to the results of tests conducted by the NASA Goddard Space Flight Center.

Description: Two spacecraft, one following the other with a separation of a few hundred kilometers and orbiting at an altitude of 160 kilometers in a 90-degree polar orbit, are used to detect the minute variations in the earth's gravitational field. One spacecraft, equipped with magnetometers, will measure the vector and scalar components of the earth's magnetic field. The scientific data obtained will provide an order-of-magnitude increase beyond the present knowledge of the earth's gravitational and magnetic fields.

Description: This paper updates a previous paper in this journal on shadowgraph and schlieren studies of gravity related fluid flow during solidification. The research has now been extended to include interferometric data by the use of a Mach-Zehnder interferometer on a NASA KC-135 aircraft flying a parabolic trajectory. It has thus been possible to obtain quantitative temperature and concentration profiles in an ammonium chloride metal-model material being solidified in microgravity. The results indicate that the growth interface is more stable under low-gravity conditions than in a terrestrial environment.

Description: Space station technology is considered along with a shuttle tethered satellite system development program, the development of advanced orbital maintenance/servicing techniques for EVA applications, human systems interfaces for space stations, materials and structures for space applications, progress in space nuclear reactor power systems technology development with the aid of the SP-100 Program, and the design of reliable power systems for communications satellites. Attention is given to problems and concepts of space station guidance and control, spacecraft data management hardware state-of-the-art, progressive autonomy, and automation in teleoperation from a man-machine interface viewpoint. A space exploration outlook is provided, and the space power systems of the early 21st century are discussed.

Description: Already in the 1930s, a discrete-coil mechanically synchronized launcher was built. At the present time, research is almost entirely directed towards railguns. However, although coaxial accelerators are more complex than railguns, they have certain unique advantages. Some of these advantages are related to the absence of physical contact requirements with the projectile, the possibility of a scale-up to very large projectile size, and the availability of up to 100 times more thrust for a given current. The price of the advantages is the need for a drive current in the form of pulses synchronized precisely with transit of each projectile coil through each drive coil. At high velocities, high voltages are required, and high voltage switching represents the technology limit on launch velocity. Attention is given to inductance gradients, the double hump, methods of excitation, methods of synchronization, projectile configuration, energy supply, fundamental limits, trends, and research needs.

Description: The application of the radiative transfer theory for semiconductors to p-n homojunctions subject to low level injection conditions is discussed. By virtue of the interaction of the radiation field with free carriers across the depletion layer, the saturation current density in Shockley's expression for the diode current is reduced at high doping levels. The reduction, due to self-induced photon generation, is noticeable for n-type material owing to the small electron effective mass in direct band-gap III-V compounds. The effect is insignificant in p-type material. At an equilibrium electron concentration of 2 x 10 to the 18th/cu cm in GaAs, a reduction of the saturation current density by 15 percent is predicted. It is concluded that realistic GaAs p-n junctions possess a finite thickness.

Description: Rad-hard CMOS/bulk inverters with input gates high and low were irradiated by protons with a nominal energy of 8 MeV in an effort to determine the total-dose and dose-rate dependence of threshold voltage shifts, both during and immediately after irradiation and over extended periods of time thereafter. It is shown that the effects in rad-hard MOS devices which are produced by specific proton and electron energies in the space environment could be simulated by cobalt-60 induced effects through careful and proper selection of total does and dose rates. This selection must be based on an experimentally established relationship of Co-60 to electron or proton damage. It is demonstrated that the simulation can be accomplished both during and after irradiation, in the long-term postirradiation period, as well as in the damage state immediately after bombardment.

Description: Motorola and National Semiconductor 54HC00 and 54HC74 microcircuits were evaluated using CO-60 to determine their total dose radiation hardness. The devices were found to be radiation soft failing parametrically between 5 and 10 K rads and functionally between 20 and 40 K rads. The failures were bias dependent, relatively insensitive to dose rate, and only annealed moderately when left unbiased at room temperature.

Description: Single-Event Upset (SEU) in bipolar integrated circuits (ICs) is caused by charge collection from ion tracks in various regions of a bipolar transistor. This paper presents experimental data which have been obtained wherein the range-energy characteristics of heavy ions (Br) have been utilized to determine the cross section for soft-error generation as a function of charge collected from single-particle tracks which penetrate a bipolar static RAM. The results of this work provide a basis for the experimental verification of circuit-simulation SEU modeling in bipolar ICs.

Description: A description of the 100-m drop tube at the Marshall Space Flight Center is presented, along with some undercooling observations and a discussion of some microstructural properties of deeply undercooled Nb-Ge alloys. The facility comprises two turbopumps which can evacuate the tube to 0.00001 torr, and three IR detectors at 15, 80, and 103-m levels which are sensitive to light in the range of 9660-2635 K (wavelength range of 0.2 to 1.1 microns), though recalescence events were detected at 1700 K. Finally, hypercooling regimes and maximum possible undercooling in vacuum are defined for several materials, including Al, Cu, Ni, Fe, Pt, and Nb.

Description: The first measurement of single event upset (SEU) for complementary GaAs static RAMs caused by heavy ions is reported. Upset cross-sections of the circuits for 28 MeV oxygen ions are reported as well as the linear energy transfer (LET) threshold established by using 170 MeV oxygen ions at various angles of beam incidence.

Description: The operation of an eight-element monolithic array of GaAlAs electroabsorption modulators has been demonstrated. The single-mode waveguide modulators are implemented in a reverse-biased p-pi-n heterojunction configuration, with center-to-center spacing of 9 microns between adjacent channels. This device may be useful for intensity modulation in high (spatial) resolution applications.

Description: Inductive mesh transmission has been measured for the two major polarizations as a function of incidence angle. The experimental data agree well with Chen's (1970) waveguide theory in the thin mesh limit. As an aid in making more rapid predictions of mesh properties, Chen's theory is used to derive an empirical lumped circuit model. This model matches the theory and experiment to one percent over critical areas of transmission.

Description: This investigation is concerned with a comparison of measured 117-GHz IMPATT oscillator frequency and output power with results derived from theoretical circuit models. It is pointed out that previous millimeter-wave oscillator models are unsuitable for studying circuit behavior, such as oscillator tuning as a function of waveguide short position or other circuit parameters. In the current study, oscillator circuit modeling techniques, successfully applied at X-band, are applied for the first time to a millimeter-wave IMPATT oscillator circuit. Attention is given to an oscillator circuit description, an IMPATT diode circuit model, a circuit model, and an oscillator analysis.

Description: An advance study has been conducted to examine the trajectory characteristics of Voyager 1 and 2 as they depart from the solar system and traverse interstellar space. A survey of the extraplanetary phase, commencing with completion of the final planetary encounters and ceasing with loss of spacecraft communication, considers the trajectory aspects attendant to a heliospheric investigation and possible sensing of a trans-Neptunian massive body. An analysis of departure telecommunications capability attempts to bound the inevitable time of communication loss. A study of the interstellar phase examines closest approaches of the spacecraft to the sun's stellar neighbours. A covariance analysis is provided to illustrate the statistical effect of stellar state uncertainties on these approaches. In addition to the Voyager spacecraft, data for Pioneers 10 and 11 are provided where appropriate.

Description: A study was initiated to design and evaluate a new design concept for nickel-hydrogen cells. This concept involved constructing a battery in a bipolar stack with cells consisting of a one plate for each nickel and hydrogen electrode. Preliminary designs at the system level of this concept promised improvements in both volumetric and gravimetric energy densities, thermal management, life extension, costs, and peak power capability over more conventional designs. Test results were most encouraging. This preprototype battery, built with less than ideal components and hardware, exceeded expectations. A total of 2000 LEO cycles at 80 percent depth of discharge were accrued. A cycle life goal of 30,000 cycles appears achievable with minor design changes. These improvements include advanced technology nickel electrodes, insulated bipolar plates and specifically designed frames to minimize shunt currents. The discharge rate capability of this design exceeds 25C. At the 10C discharge rate, 80% of the battery capacity can be withdrawn in six minutes. This data shows that the bipolar design is well suited for those applications requiring high peak power pulses.

Description: The nickel-oxide electrode common to the nickel hydrogen and nickel cadmium cell is by design the limiting or capacity determining electrode on both charge and discharge. The useable discharge capacity from this electrode, and since it is the limiting electrode, the useable discharge capacity of the cell as well, can and is optimized by rate of charge, charge temperature and additives to electrode and electrolyte. Recent tests with nickel hydrogen cells and tests performed almost 25 years ago with nickel cadmium cells indicate an improvement of capacity as a result of using increased electrolyte concentration.

Description: The power tool which will be used to replace the attitude control system in the SMM spacecraft is being modified to operate from a self contained battery. The extravehicular mobility unit (EMU) battery, a silver zinc battery, was tested for the power tool application. The results obtained during show the EMU battery is capable of operating the power tool within the pulse current range of 2.0 to 15.0 amperes and battery temperature range of -10 to 40 degrees Celsius.

Description: The battery performance of the IUE spacecraft launched in 1977 is updated. Changes made in the battery operational procedures are detailed. The aging effects after several eclipse seasons and the effects of 8 C temperature was anticipated. The batteries met their design goals and should meet the 10 year goal.