ALBERT

Notes: The various structures encountered in block and graft polymers are reviewed and a nomenclature useful for the description of these macromolecules is proposed. The concept of living polymers is elucidated and its ramifications discussed. It is shown how greatly the control of polymerization and the uniformity of the products is improved when living polymers are used as the reagents. Their application in the synthesis of block and graft polymers is illustrated by numerous examples. Other synthetic techniques yielding block and graft polymers are briefly sketched, their advantages and shortcomings being considered. Properties of block and graft polymers are described, special attention being devoted to the problems of mesomorphic phases and to the morphology of block polymers. The incompatibility phenomena observed in block and graft polymer systems are compared with those encountered in studies of the polymeric blends.Finally, the present and future applications of block and graft polymers are considered and their potential evaluated.

Notes: This study presents a mechanical analysis of the deep drawing of thermoplastics in the glassy state. A theoretical stress analysis is conducted by applying principles of classical plasticity together with several assumptions. A simple model is presented relating drawing performance with the mechanical properties of the plastic measured under the conditions of the fabrication operation. An experimental procedure is described for evaluating the drawability of a plastic. Data on thirteen thermoplastics are used to demonstrate the applicability of the theory developed.

Notes: Fracture surfaces of Epon 901/B-3 bonded aluminum alloy joints in the lap-shear configuration were studied using scanning electron microscopy. Major differences in the appearance of the fracture surface from those reported (8) for tensile loaded joints at 23°C are produced either by cyclic loading at 23°C or a change in test temperature to -196°C. Fracture in tensile loaded joints at -196°C is a brittle single step process in the opening mode in which rapid crack extension occurs throughout the joint with very little adhesive flow. Tensile fatigue fracture at 23°C is in the opening mode but crack extension is complicated by extensive adhesive flow throughout the entire joint.

Notes: When tested in tension, a cross-linked epoxy resin can be made to exhibit shear yielding. A modified von Mises criterion, τ = τ0 - μP describes the yielding behavior of the same resin under a biaxial stress system, indicating that the flow of the material is pressure sensitive.Butadien-acrylonitrile elastomer particles suspended in the cross-linked epoxy matrix induce large local deformations when the composite material is stressed. Particles a few hundred Angstroms in diameter cause the glassy matrix to exhibit shear banding, and the macroscopic failure envelope of such a system follows a modified von Mises criterion similar to that of the matrix resin. It was found that the coefficient of internal friction, τ, and the activation energy for yielding are approximately the same for the two cases. With larger particles (5-15,000 Å diam) the failure mode changes as shown by the macroscopic yield envelope and the associated activation energy. Electron micrographs of the fracture surfaces show microcavitation, similar to crazing around each particle; the deformed glassy polymer around each particle retracts upon heating the matrix above its Tg. The fracture surface work value of the unmodified matrix is 1.75 × 105 ergs/cm2. With 10 pph small particles, the value increases to 3.32 × 105 and with 10 pph of large particles, to 15.48 × 105 ergs/cm2.

Notes: The differential scanning calorimeter (Perkin-Elmer DSC-1) is used to characterize the cure of a general-purpose polyester during isothermal and scanning experiments. The technique is based on a new proposed model for the kinetics of isothermal cure. The model yields results which are in good agreement with experimental isothermal rate of reaction and integral heat of reaction data. It also gives some information about the residual reactivity of the sample after an isothermal cure experiment. With the aid of the proposed kinetic model, it is possible to obtain integral heats of reaction and rates of heat generation at different temperatures during a scanning experiment. The difference between the rate of heat input to the sample and the heat of reaction at any instant during scanning may be used to calculate the specific heat of the sample at the same instant. Specific heat data show two maxima during each scanning experiment. These maxima may be associated with transitions occurring during cure in the melt and rubbery states.

Notes: An important factor in the selection of blow molding resins for producing handled bottles is the effective diameter swell of the parison. Ideally, the diameter swell is directly related to the weight swell and would require no separate consideration. In actual practice, the existence of gravity, the finite parison drop time and the anisotropic aspects of the blow molding operation prevent reliable prediction of the parison diameter swell directly from the weight swell.The parison diameter swell is a complex function of the weight swell, the rate of swell and the melt strength. Elements of this function are presented which show the effect of extrusion rate, parison drop time and parison weight.A technique is presented which allows the estimation of local weight and diameter swell ratios. Their direct relationship is confirmed by data obtained on several blow molding resins. The relationship between weight swell and diameter swell is definitely anisotropic.A mathematical model for swell is proposed which incorporates experimentally determined rate constants and swell coefficients. Correlations are given which suggest fundamental relationships between these derived coefficients and basic variables such as resin properties or process conditions. The model's predictive capability is demonstrated by using it to back calculate parison dimensions.

Notes: Previous publications have shown that the stress-strain behavior, especially ductility, of some incompatible polymer blends are greatly improved by the addition of slurry produced chlorinated polyethylenes (CPE). This improvement is greatest for blends containing polyethylene and PVC. The most effective CPE's have some residual polyethylene crystallinity and may be described as block-like polymers with ethylene sequences and chlorine containing sequences. It is postulated that CPE addition improves the blend properties by increasing the adhesion between domains in the blend via interactions with the blend components. This hypothesis was explored by thermal analysis, dynamic mechanical testing, adhesion studies, and microscopy. It is concluded that the interaction of CPE with polyethylene derives from compatibility of rather long methylene sequences in CPE with the polyethylene which results in good adhesive bonding. The interaction of CPE with PVC may not be owing to segmental compatibility but simply good mutual adhesion between similar polar materials. There is no interaction or adhesion between CPE and polystyrene as would be expected. CPE addition to blends is accompanied by a decrease in component domain size. The relationship between CPE structure and its effectiveness as a blend modifier is discussed.

Notes: A detailed review of the material published to date on the flow properties of poly(vinyl chloride) is given. The dependence of viscosity on concentration molecular weight, molecular weight distribution, shear and temperature for concentrated and molten poly (vinyl chloride) is considered. Polymer blends and plastisols are also included.

Notes: The “melt strength” test for molten polymers is shown to be a function of several rheological parameters. Interpretation of results in terms of extensional viscosity differences is consequently not straightforward, if possible at all.

Notes: The properties of an epoxidized novolac resin cured with two homologous series of substituted succinic anhydrides (alkenyl and alkyl) have been determined and the effects of anhydride structure on properties have been evaluated. Substituted succinic anhydrides yield cured resins with lower strengths, lower heat distortion temperatures, and lower moduli. Use of substituted succinic anhydrides could broaden the range of application of alicyclic anhydrides to include those requiring a more flexible resin. Effects of specific elements of anhydride structure have been consistently interpreted from properties measurements and from aging and solvent resistance studies.

Notes: The tensile strength, fracture energy, and impact strength of ABS reinforced with discontinuous crystalline fibers such as FybexDu Pont trademark. can be controlled by manipulating fiber-matrix interfacial adhesion. In “good bonding” situations composite tensile strength, thermal expansion coefficient, and elastic moduli are significantly improved over the unfilled resin. The excellent impact strength of unreinforced ABS can be retained by lowering the fiber-matrix interfacial adhesion. This results in a corresponding reduction in the improvements in tensile and flexural strength. However, the elastic moduli and thermal expansion coefficients are relatively insensitive to changes in adhesion. Consequently, a material with high modulus (〉500,000 psi), high Izod impact resistance (7.0 ft-lb/in.), and low expansion coefficient (3.0 × 10-5 in./in./°F) can be obtained. A material with this unique combination of properties should find use in large parts such as camper tops, truck grilles, and snowmobile bodies.Fiber-matrix adhesion was measured directly by an x-ray analysis technique which could be employed because of the fiber's crystallinity and unique growth habit. This independent measurement allowed a correlation between bonding and composite properties. The interfacial bond strength was manipulated by a variety of fiber coatings and resin additions.

Notes: Differential thermal analysis (DTA) is well known for measuring temperatures and heats of physical and chemical transitions in materials. Recent development work on improved stabilization systems for polyolefin wire insulations has required fast procedures for measuring the performance of stabilization systems. Isothermal DTA procedures have been developed into routine tools for measuring stability of polyolefins by determining the oxidative induction time at elevated temperatures.Oxidative induction time has been used to study the stability of polyethylene and polypropylene in raw material form and on wire. The dependence on temperature and antioxidant concentration have been measured. Effects of oxidation catalysts, catalyst deactivators and various environmental exposures are readily observed. Techniques and apparatus have been developed for simultaneous testing of a multiplicity of samples, providing for economical large scale use of the method.

Notes: The processing of polymers typically includes steps involving heat transfer, such as quenching and crystallization. The mechanical properties of a polymer are thus affected by processing conditions, such as the amount of time spent by each portion of the polymer at each temperature in the processing sequence.This paper presents the results of a mathematical modeling study of the unsteady-state temperatures inside a crystallizing polymer during quenching. This model differs from usual methods in including temperature dependence of induction times and kinetic processes, and in not treating the polymer as a simple, small molecule system. The model permits the prediction of the final morphological distribution within the polymer. Use of the model will aid in tailoring processing conditions to produce a product with specified morphology. The method is applicable to a wide variety of problems in polymer processing, particularly for those polymers which exhibit crystallization.

Notes: A variational analysis is applied in helical co-ordinates to the problem of a developed, steady-state flow in a screw extruder. The functional involves only two dimensionless coordinates and is suitable for minimisation, e.g. by the finite element method. It is applicable to non-isothermal, purely viscous flows and contains terms representing effects of inertia, convective and conductive transport of heat, pressure gradient, and viscous dissipation. The analysis takes account of the true helical geometry and involves assumptions only in taking the fluid density, specific heat and thermal conductivity of the fluid to be constant, in regarding the fluid to be homogeneous and isotropic, and in simplifying the pressure distribution.

Notes: Viscosity and dynamic shear measurements are reported on several network forming systems as a function of reaction time and temperature. Phenolic, epoxy and EPDM rubber systems are examined. Rheological data are related to the reaction kinetics of the systems. With these relations overall activation energies, reaction orders and rate constants are interpreted from the data. These compare favorably with results in the literature.Applications of rheological techniques to processing problems of several network forming systems are described, specifically thermoset injection molding and SBR rubber vulcanization.

Notes: Two naturally occurring micas, phlogopite and muscovite, were ground and classified according to their average aspect ratios (flake equivalent diameter to thickness ratio). These flakes were then used to reinforce a polystyrene copolymer and a polyester resin. The compression molded test pieces were tested in flexure and the flexural strengths and flexural moduli determined for each aspect ratio. The experimental results indicate a strong dependence of strength and modulus on the flake aspect ratio up to a value of 100-200 for these systems. At high volume fractions, 0.6 to 0.7, high aspect ratio mica composites yielded flexural strengths of 35-45,000 psi with flexural moduli of 10-14 million psi. Notched Izod values were in the range of 0.5-1.4 ft lb per inch of notch. These results were compared with the theoretical treatments of Padawer and Beecher, and Riley.

Notes: The effect of cold rolling on the mechanical properties of polymers, viz., acetal, nylon 66, poly(vinyl chloride) and polycarbonate has been studied. The yield strength, Young's modulus, and hardness increase with increasing cold work, except for a slight drop in these properties at low values of cold work. The ductility increases with rolling to a maximum and drops with further reduction. At the same time, the tensile strength increases continuously with rolling. This conspicuous occurrence of the increase in ductility with a simultaneous increase in tensile strength for polymers, unlike that in metals, is explained considering the morphological changes produced in polymers upon cold rolling. It is shown that this typical behavior is not due to the unique loading or heating and cooling cycle involved in the rolling process.

Notes: The minimum surface strain required to induce crazing in polymethylmethacrylate and polystyrene in the presence of alcohols and n-heptane has been determined at various temperatures by bending strips of the polymers around formers of varying curvature and immersing them in the liquid reagents. For each polymer/liquid system the long-term crazing strain was independent of test temperature except within a single 30°C interval in which it decreased as the test temperature was raised. It was found that this temperature region corresponded to the glass-rubber transition of the given polymer when, after extended periods of immersion it had achieved equilibrium liquid sorption. This suggested that, in the crazing tests, a condition approximating to equilibrium sorption was being established at the craze tip and that crazing occurred on applying small strains in the presence of the liquids because of their plasticising effect.It was found that not only the plasticizing effect of the liquid environment but also the liquid molecule size influenced the crazing strain; the larger-molecule liquids caused lower long-term crazing strains than did the smaller-molecule liquids.

Notes: Plasticized polyvinyl chloride was thermally stabilized by barium, cadmium, and zinc laurates, epoxidized soybean oil, and monoalkyl diaryl phosphite, and by combinations of these stabilizers. Of 26 possible combinations, 18 showed some improvement, 8 showed useful improvement, 7 showed marked improvement, and 3 systems were outstanding. Of the 26 combinations, 10 showed distinct synergism, based mainly upon combinations of Group II-B metals with Group II-A metals, “secondary” stabilizers, or both. Combinations of Group II-B metals with “secondary” stabilizers were particularly interesting and promising.

Notes: Existing dynamic mechanical relaxation data on two polymers containing aromatic groups in the backbone chain, viz., polyimide PI, and poly(2,6-dimethyl-p-phenylene oxide), PDMPO, are reviewed and new data bearing on specimen purity and water content are presented. It is demonstrated that three separate relaxation processes are normally present in both polymers in the temperature range from about 100-400°K. The lowest temperature relaxation, designated γ, occurs in the 100-180°K range and is considered to arise from limited rotational oscillation of some phenylene rings about the 1,4 axis. Another relaxation process, designated β arises from the presence of water in the polymer. Its strength increases with increase of water content, its activation energy is about 10-12 kcal/mole, and it occurs in the 180-190°K range at 1 Hz. A higher strength secondary glass relaxation process, designated β*, occurs in the 280-400°K range at usual measuring frequencies (1 Hz to 104 Hz). This relaxation is thought to be associated with the combined reorientational motion, of rings and connecting atoms of the monomer unit in “defect” regions, or regions of poor chain packing. As such, its position is affected by sample history. Both polymers also show a rise in damping in the high temperature region indicative of additional main chain motions. In addition to the above relaxations, PDMPO shows a δ-relaxation below liquid nitrogen temperatures, associated with onset of Me rotation and PI shows an additional small relaxation near 500°K.

Notes: Polystyrene, poly(phenylene oxide), and solution-cast blends of the parent homopolymers were exposed to normal hexane in the liquid and vapor phase. The kinetics of absorption and desorption, the sorption equilibria, and the kinetics of morphological changes were studied as a function of temperature and blend composition.Absorption kinetics of n-hexane vapor in all blends were largely controlled by polymer relaxations. The sorption rates from the vapor phase varied monotonically with blend composition and increased over a range of four orders of magnitude with increasing poly(phenylene oxide) content. The equilibrium n-hexane content similarly increased monotonically with poly(phenylene oxide) content although the increase was only by a factor of two over the entire range of compositions. These results were interpreted in light of and were completely consistent with earlier findings with pure polystyrene homopolymer.Films immersed in liquid n-hexane produced a white, opaque outer shell surrounding an essentially unaffected central core. The kinetics of this whitening process were much more rapid for each of the homopolymers than the kinetics characterizing morphological changes in the blends. These data suggest that film whitening is caused by crazing in the polystyrene-rich samples and that solvent-induced crystallization is involved in the whitening of the poly (phenylene oxide) rich material.

Notes: We have investigated the low temperature transitions in a urethane prepolymer crosslinked with various amines and triols by measuring their dynamic mechanical properties over a temperature range of 25°C to approximately - 190°C. In the formulations studied, a low temperature transition was observed near - 140°C and the transition was shown to be related to the electronic and steric influences of the curing agent structure at the crosslink site. A quantitative relationship was demonstrated between the low temperature transition peak intensity and the polymer's crosslink density. The above relationships were derived from torsion pendulum and solvent swell experimentation.

Notes: Using Oxygen Index and the XP-2 test to measure flammability and smoke characteristics, a broad spectrum of thermoplastic and thermoset polymers, both commercial and experimental, were investigated to elucidate the effect of structure on fire properties.In general, polymers with aliphatic backbones are very flammable, but their tendency to generate smoke is minimal. The addition of flame retardants, especially halogen compounds, while reducing their tendency to burn, increases the evolution of smoke. Halogen-containing polymers are usually non-flammable, with high Oxygen Indices, but display high smoke generation. Polymers containing an aromatic group in the side chain, such as polystyrene, are both highly flammable and high smoke producing. However, polymers with the aromatic group in the main chain, such as polysulfone, polycarbonate and polyphenylene oxide, are intermediate in both Oxygen Index and smoke generation.After investigation of the various test methods available, it is concluded that no one test will be satisfactory to measure the flammability characteristics of polymers and that a combination of methods must be used.

Notes: Polybutadiene rubbers, filled with polydichlorostyrene or polystyrene latices having spherical diameters of approximately 500Å, were examined by small angle x-ray scattering. The filler latices were examined by x-ray scattering as a function of strain. The sample elongations ranged up to 400 percent. An analysis of the scattering of the polydichlorostyrene filler latices showed that there was deformation of the filler particles up to 25 percent. Such a deformation is not expected on the basis of the mechanical properties of bulk glassy polydichlorostyrene. However, deformation into ellipsoids of revolution is consistent with the x-ray evidence. The deformation of the latices is reasonable.

Notes: Filling cold mold cavities with hot polymer melts at high pressures is of great practical interest. The transport approach to this process of solving the general equations of change with suitable equations of state to describe the flowing material has been largely ignored. No analytic solution is possible, and the non-steady state flow adds a dimension which makes digital computation discouraging because of the core storage and execution time requirements.The mold filled in this simulation is a disk which hot polymer melt enters through a tubular entrance located at the center of the top plate. The tube is 2.54 cm. long and has a radius of 0.24 cm. The plate separation and outer radius of the disk cavity may be varied. A constant pressure applied at the entrance of the tube causes the flow. The cavity walls are kept at various low temperatures. The reported results are for rigid polyvinyl chloride (PVC).The general transport equations, i.e. continuity, momentum, and energy, for a constant density power law fluid are used to solve the flow problem. Convergence to the differential solutions is guaranteed but since a lower limit was imposed on the time increment by the core storage limit of the computer facilities (27K) and long execution times, all results are semiquantitative for the problem as stated.Using the results obtained it is possible to predict “fill times”. The formation of a frozen polymer skin as the cavity fills may be followed via the velocity profiles. The temperature profiles which reflect cooling and the amount of viscous heat generated provide the basis for studying resin thermal degradation effects.Finally, because so much of the total pressure drop is disispated in the entrance tube, and so much viscous heat is generated there, this study indicates that the design of the gate and runner system is perhaps the most important facet of success in mold filling.

Notes: A number of thermoplastic polymers were tested in tension to investigate their strain hardening behavior. A strain hardening equation has been proposed in terms of the true stress, true strain and two constants σo and m. The three material constants, viz. σo m and the true fracture strain, are shown to be adequate to describe completely the material's nonlinear viscoelastic or the so-called “plastic” behavior. The true stress-strain data for the polymers rolled to varying amounts of cold-work fits the strain hardening plot of the unrolled material. The same strain hardening equation, therefore, applies to rolled materials as well. The procedure for predicting the tensile strength of rolled materials is given.

Notes: The physical structure of a number of styrene-butadiene copolymers were investigated via dynamic mechanical and swelling studies on uncrosslinked and gamma-radiation cross-linked films that had initially been solvent cast from toluene or methyl ethyl ketone. The mechanical behavior of these films before and after crosslinking was found to depend on the material history as well as the chemical structure of the copolymer, in agreement with observations made by other experimental techniques. A simple morphological interpretation was given to the dynamic mechanical spectra as a function of radiation dosage and a limited discussion of the swelling behavior is included.

Notes: The effective thermal conductivity of a polymer liquid was measured as a function of strain rate. The polymer liquids studied were three commercial grades of polydimethylsiloxane. The experimental results show a dependence of effective thermal conductivity on strain rate. This dependence is believed due to either the rotation of large clusters of entangled macromolecules, or the orientation of the individual macromolecules, or possibly the combination of both mechanisms simultaneously in shear flow.The effective thermal conductivity, for all three samples studied, increased with increasing strain rate. The rate of increase was found to decrease with increasing temperature.The thermal conductivity measurements were made in an annular axial flow test cell that utilizes a hot wire probe technique. Convection problems were eliminated by proper placement of the temperature measuring section of the wire in the cell.A tentative model was used through which the size of the cluster can be estimated. Once the size of the cluster is obtained, the rotational contribution to the energy transport can be estimated. Initial predictions agree well with the observed phenomena.

Notes: The extrusion head systems for both pipe and blow molding were analyzed theoretically and relationships derived between pressure drop and temperature rise for various materials at different flow rates and die restrictions.Because of the complexity of the geometry involved, the die was segmented into several sections axially and momentum and energy equations for these sections were solved with the help of IBM 360. The floating boundary conditions were used in order to take into account the nature of the flow phenomenon involved.To complement and support this theoretical work, rigid polyvinyl chloride (PVC) bottle compounds were used to obtain extrusion data on a 3½ inch extruder with several different die sizes. A good agreement was found between the predicted versus experimental data. Results showed that temperature rise in the die systems in significant and that neglecting it would result in a gross error in the calculated pressure drop.Based on this work, a simplified version of the theoretical equation was developed to serve as an engineering tool in estimating pressure drop and stock temperature for a given material where extreme accuracy is not essential. Results of the engineering equation which contains several empirical constants correlate well with the data and support the theoretical effort.

Notes: Relations describing the time dependence of pressure loss in pressurized plastic containers are presented and discussed. These relations are expected to be useful in predicting the shelf life performance of pressurized plastic containers in applications such as aerosol and carbonated beverage containers. The time dependence of pressure loss in pressurized plastic containers is shown to be dependent on at least three independently contributing factors, namely gas absorption, gas permeation, and material viscoelastic characteristics. The influence of these three qualities is shown to be time dependent and expressions are presented which allow the relative importance of each to be assessed in terms of quantities that are conveniently measured in the laboratory. The pitfalls associated with defining quantitatively the effectiveness of a plastic barrier material as predicted by a steady state analysis is discussed. It is shown that such steady state analysis may be extremely misleading and may not necessarily be a measure of a material's time dependent qualities.

Notes: Pronounced effects of thermal treatment on the properties of graphite fiber/polycarbonate and glass fiber/polycarbonate composites have been demonstrated and explained. At 20 volume percent loading of random-in-a-plane, discontinuous fibers, both specimen strength and modulus in both fiber systems were found to increase dramatically upon molding above 260-265°C, whereas only the graphite system was further improved by subsequent annealing. In the latter case, property improvement is due to generation of a crystalline innerlayer at the interface, which apparently transfers the stresses more effectively from fiber to fiber. Regardless of the type of fiber, molding at 275°C (slightly above 260-265°C, the melting point of crystalline polycarbonate) results in improved properties due to better wetting of the fibers by the resin. Hot forming of graphite reinforced polycarbonate composites between the molding and annealing steps takes advantage of the higher processability of the unannealed material in addition to providing increased modulus and strength in the final molded article.

Notes: The thermomechanical spectra (∼0.5 → 1 cps) of systematically related polyimides synthesized from four aromatic dianhydrides and eleven aromatic diamines are discussed with respect to structure-property relationships and cure. In displaying two main transitions, Tg and Tβ, most of the polymers behave as amorphous materials such as polymethylmethacrylate. A different mechanism for the relaxations is invoked which involves more intermolecular interaction for those polymers (from pyromellitic dianhydride) which give more complex behavior. Difficulties in obtaining structure-property relationships in the field of high temperature rigid polymers are discussed in terms of defects in molecular structure, the effect of vitrification in freezing out reactions during cure, different chemical reactivities of the reactive precursor polyamic acids, and the effects of thermal reactions which occur in the vicinity of the glass transition regions.

Notes: The applicability of fracture mechanics to the description of initial notch extension under tension in quasi-isotropic fiberglass laminates is tested experimentally. It is found that classical elastic fracture mechanics, without modifications of couple stress effects, as represented in the theory of Muki and Sternberg, is sufficient to describe initial notch extension in prenotched specimens which are sufficiently thick to avoid transplanar bucklings of the specimen under tension. The fracture toughness (KIC) is found to be 15 ksi √in. However, it is noted that in these specimens (0.035 in. thick) transplanar postbuckling deformation becomes pronounced well before fracture, and that different modes of buckling seen in externally notched and internally notched specimens have opposite effects on the apparent fracture toughness of the specimen. It is pointed out that the effect of transplanar buckling on fracture of fiber glass, with its high compliance and high strength, is a potential source of serious problems in design with this material.

Notes: Poly(vinyl chlorides) having different melt viscosities were melt blended with several different incompatible polymers using a two-roll mill and a Brabender Plasticorder. The properties of the mixtures can be easily reproduced from batch to batch only if the viscosity of the components does not change during the mixing process. Within this limitation, the order of addition of the components during the mixture preparation does not have a significant influence on the mixture properties.The shear storage modulus of the incompatible mixtures in the temperature range between the Tg's of the components varies with the difference in component viscosities at the temperature of mixing. The moduli of these mixtures are compared to moduli calculated using Kerner's equations. Based on this comparison it is concluded that in any incompatible mixture the component having the lower melt viscosity at the temperature of processing tends to form a continuous phase in the mixture. The greater is the viscosity difference, the greater is this tendency. The viscosity of one component relative to the other can be changed by changing the molecular weight of the components and/or the temperature of mixing.

Notes: Most organic polymers are damaged by exposure to terrestrial sunlight and eventually the useful properties are lost. Once absorbed, radiation in the erythmal region of the solar spectrum has sufficient energy to cause the rupture of polymer chain bonds.It can be difficult to identify the important chromophores in a polymer system and even more difficult to determine precisely what happens to them following electronic excitation. The number of chemical events leading to the mechanical failure of a plastic can be remarkably small although the variety of them is potentially large.Polypropylene is discussed as an example of a thermoplastic which invariably contains small amounts of light-absorbing impurities and which, if unprotected, is highly susceptible to photo-oxidation. Polyethylene terephthalate is used to illustrate a class of polymers which is susceptible to actinic deterioration owing to chromophores in the repeating unit. The primary photochemical reactions occurring in these two systems are described, with improved methods for UV stabilization in mind.

Notes: Zinc laurate was a powerful but short-lived primary stabilizer. Epoxidized soybean oil, catalyzed by a trace of zinc, was a fairly good primary stabilizer. Organic phosphite ester served primarily to prevent premature failure due to zinc; phosphite/zinc mol ratio of 4.5/1 was optimum. These combined effects are consistent with present theories of stabilizer synergism, and also suggest some further possible mechanisms. Practically, the 3-component system offers a low-cost, efficient, non-toxic stabilizer for plasticized polyvinyl chloride.

Notes: The various types of extensional flows and extensional viscosities are defined and methods of measurement discussed. The role that each of these extensional viscosities plays in various polymer fabrication processes is discussed with examples. Finally, it is shown how engineering analyses of these complex flow fields are conducted using simplified phenomenological equations for the rheological behavior. This approach is recommended for use until such time as tensorially correct, mathematically tractable constitutive equations that are based on molecular theory are available.

Notes: A new method for the measurement of the Poisson's Ratio function of the more rigid plastics is described. The deflection of a freely-supported circular plate under uniformly distributed load is combined with modulus data obtained in an independent experiment. The apparatus is described, the validity of the relevant elastic stress-strain formulae are discussed and the results obtained on PMMA and PVC are compared with other published values. It is concluded that this method is at least as accurate as the alternatives, all of which have particular deficiencies, and that it is possibly superior in some respects.

Notes: Coextruded plastic films containing 231 alternating layers of polystyrene and polymethylmethacrylate have been made with individual layer thickness in the range of .06-0.1μ. Due to the difference in refractive indices these unique films can be made to reflect portions of the visible spectrum, yielding a highly iridescent appearance.Reflectivity measured on films of known layer thickness distribution correlated with values predicted from optical theory.

Notes: Several theories have been advanced to explain the toughening of glassy plastics by rubbery modifiers. These have been based primarily on studies of high impact polystyrene or ABS systems, where the crazing mechanism has been shown to be most applicable. In the present study, the effects of MBS (methacrylate-butadiene-styrene) impact modifiers on PVC have been studied, utilizing both physical and microscopic techniques. Tensile test results indicate that a primary contribution of the modifier to increased toughness is a lowering of the yield stress of the PVC. Electron microscopic studies and density determinations on strained samples indicate no crazes in these MBS-modified PVC systems. These results suggest that the mechanism of impact reinforcement in PVC is based on the enhancement of localized yielding in the vicinity of the rubbery modifier particles.

Notes: Heat transfer to a flowing thermally softened polymer (polymethylmethacrylate) has been studied. Experimental temperature profiles were determined at various axial lengths. The data are both precise and reproducible. Sizeable viscous dissipation was found to occur. This effect was found to be greater for polymethylmethacrylate than a molten polymer (polyethylene). Cooling as well as heating data were found in this work. The experimentally determined data checked qualitatively with the data computed from a prior analytical solution of the equations of motion and energy.

Notes: A mathematical model was developed to predict the dynamic behavior of flowrate and melt temperature in a plasticating extruder caused by changes in operating variables such as screw speed, back pressure and barrel temperature. The model has application for on-line computer control of an extrusion process or for simulation purposes off-line. Experimental data for developing the model was obtained from a 2½ in. diameter plasticating extruder producing high impact polystyrene sheet.

Notes: A theoretical model is proposed, for certain barrier type fluted mixing sections of extruder screws. Screws with such mixing sections are occasionally used in plasticating extruders. With the aid of this model, these screws can now be quantitatively simulated in the design stage. Specifically the model enables the calculation of pressure change across the section as a function of geometrical configuration of the mixing section and operating conditions.A generalized set of curves, plotted in dimensionless form, for quick manual computation is also given. With its aid, the effect of the design variables on the pressure change is discussed.Finally, mixing section-zones, in reference to the plasticating extrusion theory, and the state of the art of extrusion theory are very briefly discussed.

Notes: Creep data in uniaxial tension, compression and shear on PVC, PMMA, and PP sheet were used to test analytical correlating procedures. It was shown that shear and uniaxial creep could be closely related using the concept of shear stress and shear strain on octahedral planes. This correlating procedure was only effective if due allowance was made for the different creep response in simple tension and compression for each of these materials. It was also shown that the relationship between the viscoelastic creep moduli and strain ratio, which is stress and time dependent, has the same form as the analogous relationship between the linear elastic constants.

Notes: Surface microscopy studies have revealed the phase separation and exudation of a phenol type of antioxidant [4,4′-thiobis (3-methyl-6 tert. butyl phenol)] from polyethylene at concentrations of 0.08 percent by weight. The equilibrium solubility of the antioxidant in polyethylene was estimated to be less than 0.01 weight percent at room temperature.About 70 percent of the antioxidant was expelled from a thin polyethylene film after storage for three days at 70°C. Since the initial concentration of the stabilizer is typically 0.10 percent of the polymer by weight, the antioxidant exudation can lead to a serious shortening of the expected life of the polymer. Prediction of lifetime by accelerated aging tests must account for the depletion of the stabilizer by exudation. The life of stabilized samples should be measured at concentrations which do not exceed the solubility limit of the antioxidant in polyethylene at its use temperature.

Notes: Four glands of the house sparrow, chicken and turkey were examined histologically and for their content of amylase. These were the external and intermediate mandibular glands, the maxillary gland and glandula anguli oris of the sparrow and the anterior and posterior mandibular, maxillary and anguli oris glands of the chicken and turkey. Amylase was determined by a starch substrate slide method and by biochemical assay. General morphology and mucopolysaccharide staining are described.All four glands of the sparrow demonstrated significant amylolytic activity by the assay. In the external mandibular and anguli oris glands this activity could be traced to mucous and seromucous cells of origin by means of the starch substrate slide procedure. None of the glands of the chicken or turkey displayed significant amylolytic activity.

Notes: A cinematographic analysis of the unrestrained walking, trotting, galloping, jumping and landing movements of 11 adult cats was undertaken to provide previously unavailable information concerning the demands imposed on the nervous system for the control of low and high speed movements and the demands imposed by such natural movements on muscle performance and proprioceptive response.With due regard for the swing (F and E1) and stance (E2 and E3) phases of the step cycle of an individual limb, single frame analysis of the film permitted measurement of instantaneous angles of the lower spine, hip, knee, ankle and metatarsophalangeal joints. Appropriate lever arm measurements were also made on 50 freshly dispatched cats and 25 cadavers such that the Law of Cosines could be used to calculate instantaneous lengths of select hind limb muscles that would apply to the natural movements of adult cats of small (1.5-2.5 Kg), intermediate (2.6-3.5 Kg) and large (3.6-4.5 Kg) size. Muscle displacements were analyzed relative to maximum and minimus in situ lengths and the lengths associated with quiet standing. Use was also made of a previous electromyographic analysis of hind limb muscles during unrestrained locomotion (Engberg and Lundberg, '69).The sequential relations between the four phases of the step cycle are maintained as forward speed increases from walking ( 〈 2 mph) to high speed galloping ( 〉 16 mph). There are significant differences in the time consumed by each phase, however, with a greater reduction in the E3 phase, little reduction in the E2 and E1 phases and virtually no reduction in the F phase. When each phase is expressed as a relative percentage of the duration of the total step cycle, the greatest reduction is again in E3 with little change in the E2 phase. In contrast F and E1 phases increase in the percent of time they occur in each cycle, with the greatest increase in the F phase. For all speeds, analysis of the phase relations between movements of various sections of the hind limb revealed a remarkable unity of knee and ankle joint movement. The hip joint is largely out of phase with the knee and ankle during E1 and E2, all three joints being in phase in F and E3. The digits are essentially out of phase with the other joints except in the stance phase of the gallop.Rates and extents of muscle displacement during natural movements are greater than might be anticipated when expressed in absolute mm's and mm/sec but not when considered in relation to maximum and minimum in situ length and the length associated with quiet standing (Ls). During stepping a progressive increase in forward speed results in: (a) a greater usage of muscles at lengths between Ls and maximum in situ length; (b) for knee and ankle extensors, pronounced increase in the lengthening contraction associated with the E2 (yield) phase of step; and, (c) for both flexor and extensor muscles, an increased active phase of lengthening or near isometric contraction immediately prior to periods of active shortening. In contrast to these changes in active muscle status, the change from walking to galloping has little effect on the extent and rate of passive muscle displacements, particularly the F phase stretch of extensors.For the soleus muscle, calculations were made of the relation between changes in overall muscle length during natural movements and the length of the average muscle fiber and the tendon of insertion. These measurements revealed that the increases in fiber length when passive and decreases in length during active shortening are less than would be anticipated from the extensive liteature on extirpated fibers. In contrast, the increase in fiber length when active is greater than would be expected from the admittedly sparse literature on this subject.The results of this study are discussed largely in relation to two points of neurophysiological interest: the physiological range of muscle stretch as it pertains to the responsiveness of muscle spindles and tendon organs; and those mechanical aspects of lengthening contractions that give insight into the neural control of stepping. For exciting both spindles and tendon organs passive muscle stretch and shortening contractions are shown to be relatively ineffective and lengthening and isometric contractions particularly effective movements. It is suggested that, just as recent literature has emphasized the co-activation of efferent alpha and gamma motoneurons as a muscle becomes active, so too is there a synchronous activation of afferents, particularly the Ia and group II endings of muscle spindles and Ib endings of tendon organs. Finally the thesis is advanced that, while it has been convenient to separate E2 from E3 in the description of the stance phase of the step cycle, extensor muscles are actually undergoing a single mechanical event: an active stretch-shorten cycle for knee and ankle extensors and an active isometric-shorten cycle for hip extensors. This hypothesis has significant implications for the neural control program that regulates the stepping sequence in that it emphasizes the extent to which appropriate changes must be preprogrammed in the mechanical properties of muscles for the smooth execution of stepping.

Notes: Cytological and cytochemical methods were used to identify and characterzie six distinct regions of the crayfish kidney: coelomosac, labyrinth I and II, and nephridial canal I, II, and III. Cells of the coelomosac possess cytoplasm which is strongly PAS-positive, but poor in RNA and protein. Their nuclei possess unusual projections which extend to the basal plasmalemma. Labyrinth I contains columnar cells rich in glycogen. Labyrinth II is characterized by a distended lumen and by shorter cells with high cytoplasmic RNA, many possessing a large intracellular vacuole. A PAS-positive brush border is unique to the two portions of the labyrinth. Cells in the nephridial canal show strong reactions for RNA and Mg++-dependent ATPase. In nephridial canal I and II, cells are flattened to cuboidal with the lumen being more distended in nephridial canal I than anywhere else in the tubule. In nephridial canal III, the cells are large and columnar, and the cytoplasmic RNA concentration is greatest apically. Nuclei in all regions of the tubule epithelium, except coelomosac, are large and react strongly for protein. Coelomosac nuclei and those in blood cells are condensed and contain little protein. The cytoplasm of blood cells displays a significant amount of RNA, and traces of polysaccharide material.These observations demonstrate the presence of highly specialized morphological and histochemical alterations along the length of the kidney tubule and indicate sequential modification of urine in the lumen. Evident morphological and cytochemical likenesses between analogous regions of the mammlian nephron and the crayfish kidney tubule suggest that basic physiological similarities may also exist.

Notes: In the tiger salamnder the distribution of optic fibers, as revealed by the Fink-Heimer method, is compared with the localization of acetylcholinesterase, as revealed by histochemical methods. AChE activity coincides with optic nerve axons in the optic fiber layer of the retina, in the optic nerve, in the optic tracts and in every optic projection. Reginons of optic fiber terminals show heavier activity than optic fibers of passage. Comparison with other vertebrates is also made.

Notes: Light and electron microscope studies indicate that the old ependyma just proximal to the plane of amputation in early lizard tail regenerates shows a sequence of morphological changes which suggests that it as well as the new ependyma growing into the regenerate may play an active role in the initiation and maintenance of early tail regeneration.The old ependyma close to the plane of amputation undergoes hypertrophy and/or hyperplasia causing a partial closure of the central canal and pseudostratification. Its nuclei shift from an original apical position to a basal one. The ependymal processes become more prominent and extend to the pia, a condition not found more rostrally. There is also a significant increase in the amount of Golgi substance and a moderate increase in the rough endoplasmic reticulum. These observations lead to the thought that these cellular changes may be an expression of enhanced secretion and other activities in the old and new ependyma just proximal or distal to the plane of amputation.

Notes: The dorsal proctodeal wall of the Coturnix contains a gland which is especially well-developed in the sexually active male and which secretes a foamy exudate. This gland has not been recorded in any other genus of birds and appears to be unique to members of the genus Coturnix. On the basis of its location in the adult we have named this gland the proctodeal gland (glandula proctodealis). Structure of the gland does not conform to any curently defined category of glands because it is an aggregate of individual glandular units each of which opens independently into the proctodeal cavity but with the entire structure enclosed by a connective tissue capsule. We have thus characterized it as an aggregate gland. Observations on the arrangement and composition of the fibrous capsule and its intimate relationship to the perimysium of M. sphincter cloacae indicate that release of the secretion probably results from contraction of the cloacal musculature. Preliminary data suggest that development of glandular tissue in the female may be a function of age rather than of androgen sensitivity which characterizes the male gland. It is concluded that the chemical nature of the glandular secretion and its function in the sexually active bird, as based on presently available information, remains unknown.

Notes: Wound healing in the integument of the sea cucumber, Thyone briareus, was studied for up to 50 days after inflicting wide excisional wounds and for 14 days after producing incisional wounds. Rapid re-epithelialization of the wound was effected by the migration of epidermal cells and pigment cells from the periphery of the wound margin. This occurred without apparent evidence of concomitant mitotic activity. Dermal wound healing was completed by the fourteenth day in the incision wounds but occurred very slowly in the broad excision wounds. Morula cells seem to be involved in both epidermal and dermal wound healing, although their precise role is unknown. In excisional wounds the integument was never completely restored to its normal appearance during 50 days of observation.

Notes: Some of the cytological and histochemical characteristics of hemocytes of Thyropygus poseidon were studied. Jone's system of classification of hemocytes was extended to millipede hemocytes. Seven classes were identified as prohemocytes, plasmatocytes, granular hemocytes, cytocytes, oenocytoids, spherule cells and adipohemocytes. Oenocytoids were rarely found. All cells except prohemocytes and oenocytoids sequestered oxidized products of catechol. Results of the histochemical tests for proteins also suggest that these cells sequester plasma proteins. Cytocytes do not bring about any visible coagulation similar to the hemocytes of some hemipteran insects. Granular hemocytes contain phenol-oxidase capable of oxidising tyrosine as well as catechol, similar to the hemocytes of crustaceans. In this respect millipede hemocytes differ from insect hemocytes. It is suggested that these cell types may represent distinct cell lines and may not represent transformation of one cell type to another.

Notes: Twenty-three stages in the embryonic development of the western painted turtle, Chrysemys picta bellii are described. The staging is based primarily on morphological changes, as well as age and size of the embryo.

Notes: Scanning and transmission electron microscopy were used to investigate the surface area and number per unit area of microvilli from jejunal villus epithelial cells in the rat, hamster and dog.The calculated mean microvillus surface area was 0.419 μ2, 0.573 μ2, 0.751 μ2 for the rat, hamster and dog respectively.The largest number of microvilli per square micron freeze dried villus surface was measured in the rat with a mean value of 65. Hamster and dog freeze dried specimens had lower mean values of 54 and 34 microvilli respectively.The total microvilli surface area in square micron per square micron villus surface was more closely related for the three species with values of 27.23 for the rat, 30.94 for the hamster and 25.53 for the dog.These data indicate an inverse relationship between the mean microvillus surface area and population density in the species studied. However, the total microvilli surface area per unit villus surface is relatively similar for the three species.The observed number of microvilli per unit villus surface was shown to vary depending upon the dehydration technique employed for preparation of scanning electron microscopic specimens. This variation probably reflects shrinkage artifact and should be considered in soft tissue studies involving the scanning electron microscope.

Notes: In Esox americanus and Esox niger (Esocidae) there are two types of surface pits, sensory and nonsensory. Both types of pits are morphologically very similar and are associated with modified (cardioid) scales. The pits are distinguished by the presence and absence respectively of neuromasts. Ultrastructure of the neuromasts indicates that they are basically similar to previously described neuromasts. However, the hair cells have crystalline-like deposits in the nuclear region. The nonsensory pit contains a small group of distinct epidermal cells, called central cells. These cells occupy a central position in the pit, similar to that of the neuromasts in the sensory pit. The central cells are unlike any cell types described for fishes, and on an ultrastructural basis no function can be ascribed to them and the significance of the nonsensory pit is unknown.

Notes: Esox americanus and Esox niger (esocidae) possess two types of surface pits, sensory and nonsensory. The pits are morphologically very similar and both are associated with modified (cardioid) scales. The pits are distinguished by neuromasts in the sensory and central cells in the nonsensory pit.Neuromasts and central cells are responsible for the formation and maintenance of respectively the pit and cardioid scale. This supports an extension of the epidermal co-participation hypothesis that epidermal cells control the form of dermal structures in addition to contributing to composition.The central cells are similar in structure to induced primordial cells of regenerating neuromasts.The development of primordial cells may be arrested and the cells maintained in a static condition during which time they still influence the dermal tissues and maintain a pit and cardioid scale. Essentially this represents the experimental conversion of a sensory pit into a nonsensory pit. This evidence is taken in support of the hypothesis that the nonsensory pit and central cells represent an aplasic condition of the lateral line system.

Notes: The gular gland of the bat Tadarida brasiliensis is a specialized sebaceous gland located in the skin of the suprasternal region of adult males. It consists of an aggregation of simple branched tubulo-acinar gland units, the number of which varies seasonally. Each acinus is composed of densely packed sebaceous cells at various stages of differentiation. Acinar basal cells and cells of the epithelium of the ducts can differentiate into sebaceous cells. Two main changes appear in the cytoplasm concurrent with the sebaceous transformation: the differentiation of cytoplasmic organelles and the deposition of lipid material. The appearance of a different type of mitochondrion and the development of large numbers of ribosomes and polyribosomes can be recognized in the cytoplasm at an early stage of differentiation. Concomitant with the deposition of significant numbers of lipid droplets, the cells develop abundant agranular endoplasmic reticulum occurring mainly as scattered tubular cisternae. These at times form whorls surrounding lipid droplets. At later stages, the cisternae of the agranular endoplasmic reticulum often occur in crystalline arrays between secretory oil droplets. The roles of the different cytoplasmic organelles, especially in relation to the production of sebum, are discussed.

Notes: The mutant gene srn produces sireniform abnormalities in the mouse. The effects of this gene on normal prenatal development were examined histologically by retrograde analysis from day 10 through day 18 of gestation.The sireniformphenotype is characterized by the fusion of the hindlimbs and accompanying defects of the posterior appendicular skeleton. Visceral defects involve the urogenital system and the lower intestinal tract. A single umbilical artery arises from the dorsal aorta and controls the fetal circulatory pathway normally mediated by the lateral umbilical arteries. This artery is believed to have resulted from the fusion of the paired primitive umbilical arteries.It is suggested that the srn mutation causes a narrowing of the posterior amnion early in development. The resulting abnormal pressure causes a dorsal displacement of the hindgut, allowing fusion of the hindlimb buds. Abnormal structural relationships and pressure in the narrowed posteriior region disrupt normal urogenital and intestinal development and increase the proximity of the primitive umbilical arteries.

Notes: The retinofugal projections of the snake Thamnophis sirtalis were studied by the method of experimentally induced Wallerian degeneration stained by the Fink-Heimer method. The retinal ganglion cells project to all parts of the contralateral lateral geniculate complex, nucleus lentiformis mesencephali, nucleus geniculatus pretectalis, nucleus posterodorsalis, basal optic nucleus and superficial layers of the optic tectum. In addition, the retinofugal projections were observed terminating in portions of the ipsilateral lateral geniculate complex and nucleus posterodorsalis.Examination of the morphology of the retinal terminal areas stained for Nissl substance with cresyl violet led to the conclusion that these regions are well differentiated and should not be considered poorly developed when compared with other reptilian forms such as turtles.

Notes: The course of the statoblast formation in Pectinatella gelatinosa was divided into four stages and studied histologically and histochemically. The bottom of the cystigenous cup is a center of cystigenous cell differentiation and the peripheral zone of the inner cystigenous layer turns to the outer cystigenous layer as the cystigenous cup grows. The annulus is formed by migration and transformation of the outer cystigenous cells.During early stages, the yolk cells have an intensely pyroninophilic or RNA-rich cytoplasm. The cytoplasmic pyroninophilia then diminishes as the amount of yolk granules increases.Several kinds of yolk substances occur in the mature statoblast. During statoblast formation glycogen appears first, then glycoprotein and finally neutral unsaturated lipid.Acid phosphatase activity is associated with granular structures in the cytoplasm. In the cystigenous vesicle, acid phosphatase activity is low and confined to the apical extremity of the cell. Histochemically detectable alkaline phosphatase activity is not involved in the formation of the statoblast.

Notes: The anatomy and physiology of feeding in miniature swine were studied, using gross dissection, electromyography, cinematography, and cineradiography.Small particles are preferred for ingestion, and large items are usually broken down outside of the oral cavity. The particles are initially picked up with the lower lip and then retrieved by the tongue; the tongue very rarely leaves the oral cavity. Geniohyoid, mylohyoid and digastric are the most active muscles during food collection.Mastication is fairly rapid (3 cycles/sec) and involves a transverse component which may be either medially or laterally directed. The direction of motion is generally reversed with every chew. Electromyography indicates that the transverse rotation is caused by a force couple consisting of protrusors (masseter, medial and lateral pterygoids) on one side and retrusors (zygomaticomandibularis and temporalis) on the other. The direction of the rotation is not necessarily related to the side containing the bolus. Mandibular depression is electromyographically biphasic. Concurrent tongue and hyoid movements complicate the interpretation of activity patterns in the oral floor.Both masticated food and liquid are stored between the tongue and the soft palate and epiglottis before being swallowed. Swallowing involves very strong activity in all of the hyoid and tongue muscles and very low activity in the adductors. Liquid is taken in by suction rather than lapping.Comparisons with other mammals are presented.

Notes: The wall of the gametolytic gland in Aplysia and Phyllaplysia consists of a muscular layer lined with an epithelium incorporating four distinct cell types, some of which show intense secretory activity. The cytoplasm of these cells, rich in RNA, has a peripheral layer of densely-packed mitochondria in association with a smooth endoplasmic reticulum. Lipid globules, perhaps resulting from absorption of lumen contents by microvilli, appear in the cytoplasm in the course of growth and reproductive activity. A basal band of fibrillar material appears to serve as a cytoplasmic skeleton. The elaboration of cell types, extensive areas of cytoplasmic RNA, and vigorous secretory activity suggest important roles for this organ such as development of food reserves, recycling of sexual materials of high physiological value, and interaction with the bag cells of the nervous system in coordinating ovulation with the availability of capacitated, exogenous sperm.

Notes: The predaceous neotropical characoid fish Ctenolucius has an essentially homodont dentition, the number of teeth increasing linearly with age. The basic manner of tooth replacement suggests that Ctenolucius is a primitive characoid. Tooth replacement continues throughout life and is similar to that of tetrapods, involving replacement waves which pass from the back to the front of the jaws. The waves containing the greatest number of teeth are found just anterior to the middle of the jaws. In the upper jaw the increase in the number of teeth is restricted to the anterior portion (premaxillary) whereas the number on the posterior part (maxillary) remains constant. In specimens measuring from 68-230 mm in standard length the posterior portion of the upper jaw doubles in length whereas the anterior portion triples. It is suggested that the area immediately anterior to the middle of the jaw, where replacement waves are longest, is where most of the increase in tooth numbers occurs.During growth of the teeth the absolute height is always greater than the absolute width as the shape changes. The final shape of the recurved conical teeth is determined only in the last stages of tooth formation when the main axis of growth abruptly changes.

Notes: Improved histological procedures have revealed in some detail the form and structure of auditory receptor organs in the frog. These organs, the papilla amphibiorum and papilla basilaris, are located in extensions of the saccular cavity, and lie in a path of vibratory fluid motion beginning at the columellar footplate and extending in a continuous circuit through the perilymph spaces and the round window back to the middle ear region.These organs exhibit great uniformity, and for the amphibian papilla there is a high degree of complexity in the tectorial structures that overlay the ciliated ends of the hair cells. In both papillae a “sensing membrane,” which is a derivative of the tectorial body, lies in the path of fluid flow and aids in the stimulation process.The mode of stimulation of the hair cells in the amphibian ear is peculiar, and in principle is the reverse of the familiar one of reptiles, birds, and mammals.

Notes: To determine the prism sheath configurations in human cuspal enamel 80 teeth were initially ground to produce flat surfaces through the following planes: a horizontal series at successively greater distances from the dentinoenamel junction and longitudinally through the center of the cusps. Individual teeth were suspended in an acid-alcohol solution (1 cm3 conc. HCl in 100 cm3 95% ethanol) at 37°C for seven to ten days. The treatment “softened” the enamel to a depth of approximately 1 mm. The teeth were embedded in Epon and sectioned at 0.5 to 10 μm with a diamond knife. Thick and thin ground sections for phase contrast microscopy and acid-etched ground sections for Nomarski differential interference microscopy were prepared through the same regions. In thicker longitudinal sections, the prisms in gnarled enamel formed a zig-zag pattern which was unlike the twisting pattern generally observed in ground sections. The thinnest transverse sections showed the sheath outlines to be dramatically different from those seen elsewhere in the enamel. Some prism sheaths were circular, others were in the form of spirals. What could be described as sheaths within sheaths were also seen. In the thinnest longitudinal sections the prisms were seen to be elongated and discontinuous. Sheath outlines in enamel adjacent to the central core of gnarled enamel were similar to those described elsewhere in the body of the enamel. Keyhole, modified keyhole patterns and arcade forms were the dominant sheath patterns. Other atypical sheath configurations were seen scattered throughout this region.

Notes: The differentiation and degeneration of the cement gland in Xenopus laevis is described. The gland is first observed histologically at stage 19 (neural tube stage) as a packed group of apical ectoderm cells heavily laden with oocyte pigment granules, lying ventral to the cranial neural fold. By tailbud stage 35/36, the gland cells have increased in height and are approximately ten times taller than nonglandular apical ectoderm cells. The nuclei divide the gland cells into an apical region that is eosinophilic and contains oocyte pigment granules, and a basal region that contains clear droplets. The cells are decreasing in height by stage 40 (early tadpole) and begin to lose their pigment granules. Between stages 45 and 48, the pigment is extruded and the clear basal droplets diminish in number. From stage 48 to 49 the cells become vacuolated and the histotypic characteristics of the functional gland are lost. The gland is not vascularized, nor do phagocytic cells appear in its vicinity during any stage of its development. It remains bordered at its base by subjacent basal ectoderm during its entire life cycle of 10 to 12 days at room temperature.

Notes: The morphology of the rectal pads of two cockroaches, Blattella germanica and Blaberus giganteus is described and contrasted with that of Periplaneta americana, studied previously. The columnar absorptive cells of the three species are similar in structure. However, Blattella and Blaberus rectal pads have a second type of cell, termed the secondary cell, that is not present in Periplaneta. The secondary cells are embedded in the pad epithelium and have crypts of cavities opening into the subepithelial sinus. In addition, a multilayered sheath is present between the pad cells and the sinus. The sheath acts as a barrier, perhaps of low permeability, between the subepithelial sinus and the pads. It is interrupted only at the borders of the secondary cells. A mechanism for fluid absorption is presented and the possible role of secondary cells is discussed. It is proposed that the secondary cells reabsorb solute from the sinus and that this solute can then be recycled through the pad cells. Structures resembling neurosecretory terminals within the cavities of the secondary cells may be involved in regulation of recycling. The arrangement of the rectal pads in these insects has structural and perhaps functional similarities with other transporting systems, particularly the cryptonephric system.

Notes: Pyroantimonate precipitate indicates that the epithelium of the proximal tubule is the only segment of the tubular nephron of the fresh water lamprey where large accumlations of cations are distributed. Unusually large amounts of reaction product are located within the lateral intercellular spaces and within vesicles closely associated with the plasma membrane at the lateral and basal surfaces. This technique suggests the continuity of these vesicles with the plasma membrane and alludes to the possibility of an endomembranous system of vesicles and the intercellular spaces as vehicles for ion transport. Lateral intercellular spaces of proximal tubules of lower vertebrates may play a different role in kidney function that their counterparts in higher vertebrates.Osmium-zinc iodide has a specificity for certain cells within the proximal, intermediate, and distal segments, but no structural differences are noted when these cells are compared to unstained cells. Smooth endoplasmic reticulum remains unstained in the distal segment but the stain has a strong affinity for elements of the Golgi apparatus, lysosomes, and the nuclear envelope of all cell types. This technique does not suggest a structural or functional similarity between cells of the distal segment and the chloride cells of the gills of teleosts.

Notes: Anatomical analysis of the forebrain and midbrain of Anelytropsis, Dibamus and feyliniids reveals structural similarities with those of skinks and snakes. Skinks and feyliniids are probably derived from a common ancestral stock. This is suggested by mutual reduction of several telencephalic nuclei, by similar trends in the development of the dorsal thalamus, and by similarities in the lamination of their optic tecta. Anelytropsis, Dibamus, feyliniids and snakes show interdigitation of the periventricular gray zones of the optic tectum and enlargement of lamina 7 of the posterior colliculus. Of these three taxa, Dibamus is most similar to burrowing snakes and many of its brain characters are intermediate between skinks and burrowing snakes. These similarities may suggest common ancestry between Dibamus and snakes rather than parallelism.

Notes: It is possible to monitor the electrical activity of the motor neurons of Drosophila by recording the electrical activity of the muscle fibers. We have found that it is possible to specify the location of the subcuticular terminations and to describe the orientation within the thorax for the individual muscle fibers, because of the large size of the fibers and because the surface anatomy of Drosophila is known in detail. A map has been made to indicate the location of the muscle fibers with respect to superficial landmarks. The importance of the stereotaxic map for physiological studies is discussed.

Notes: The functional anatomy of pulmonary ventilation in Thamnophis elegans was studied by electromyography. Flow of air into and out of the lungs follows a triphasic pattern and occurs while the glottis is held open by a dilator muscle. Non-ventilatory rest periods characterized by a closed glottis and lack of ventilatory movements occur between breaths. Exhalation is caused by contraction of a pair of dorsolateral sheets of muscle that extends from the ventral surface of the vertebral column to the medial surfaces of the ribs and a pair of ventro-lateral sheets that extends from the medial surfaces of the ribs to the mid-ventral skin. Inspiration is powered by contraction of a series of rib levators and retractors. The last phase of the ventilatory cycle is a passive expiration that may be caused by elastic recoil of the walls of the filled lungs and relaxation of muscles used during inspiration. The site of respiratory pumping is shifted craniad after large prey items have been completely ingested. The significance of this shift and its anatomical basis are considered.

Notes: Histological studies of the neurosecretory system during the postembryonic development of a spider, Argiope aurantia, were made at the light-microscopic level.Neurosecretory cells which are found in all stages are classified into type I and type II cells. The type I cells are present in the aboral region of the brain and in pedipalpal, ambulatory and abdominal ganglia of the subesophageal mass. The type II cells which appear from the seventh stage are confined to the cheliceral ganglia. Three stages of secretory activity (poor, medium and full) based on stainability are described in these cells.In both types clear axonal transportation of neurosecretory material is observed. The discrete tracts and commissures formed by these neurosecretory axons are described in the brain and subesophageal ganglion. The complexity of some of these pathways is comparable to that of the ordinary neurons.One pair of nerves from the brain and four pairs of nerves from the subesophageal mass enter a neurohaemal organ, the Tropfenkomplex. This is a paired structure, situated dorsally, on either side of the subesophageal mass. The neurosecretory axons branch extensively within the organ and on their course they from sacs or pools filled with secretory material.The Tropfenkomplex is enveloped by a thin neural sheath which runs deep into the organ dividing it into a series of lobes. Glial cells are distributed within the organ. As in the neurosecretory cells, changes in stainability of secretory material were also observed in the Tropfenkomplex.During intermolt periods two peaks of stainability have been noticed. The first peak lasts for 24 hours after the molt, and this is followed by a low activity period between second and fifth day. From the sixth to the tenth day after the molt the second peak commences. It is suggested that the second peak may be responsible for bringing about molting.The cheliceral group appears (seventh stage) at a time when external indication of reproductive characters are visible. In the ninth stage, by the tenth day after the last molt, several of the type I and type II cells contain much secretion. This is followed by maturation of gonads and oviposition. Thus both type I and type II cells are believed to be involved in the reproduction of the animal.

Notes: Ovaries of the giant silkmoth Samia cynthia Drury have been studied histologically and histochemically during diapause, adult development, and after injury to the diapause animal. In addition to cellular changes involved in follicular growth and vitellogenesis, changes in the intermediate layer cells are very striking, showing a distinct pattern during ovarian development and after injury. Two types of granules, one periodic acid-Schiff (PAS) positive, the other paraldehyde-fuchsin (PF) positive, change in their number and distribution in the intermediate cells during development and after injury. The PAS-positive granules appear during the first one-third of development, increase in number and size until the tenth day, then gradually dwindle in number and size, and disappear in the adult cells. The PF-positive granules, present in moderate numbers in the diapause animal, decrease in number until the tenth day of adult development, then reappear, and are present again in adult intermediate cells. After injury to a diapause pupa, intermediate cells show a greatly increased number of PF-positive granules, but none that are PAS-positive.The PAS-positive granules are a neutral or mildly acidic mucosubstance, and may correspond to lysosomal activity, while the PF-positive granules may be a neurosecretory-like substance or the product of hormone-dependent protein synthesis, since the patterns of granule distribution in the intermediate cells seem to reflect both general metabolic and hormone-related events.

Notes: The distribution of monoamine (catecholamine and 5-hydroxytryptamine)-containing nerve cell bodies in the brain stem and hypothalmus of the frog (Rana temporaria) was investigated with the help of the histofluorescence technique of Falck and Hillarp ('62). At the level of the hypothalmus of this amphibian brain, catecholamine-containing nerve cell bodies are found mainly within three areas of the periventricular gray substance, namely the peroptic recess organ, the paraventricular organ and the lateral recess region. On the other hand, most of the 5-hydroxytryptamine (serotonin)-containing nerve cell bodies of the brain stem of Rana temporaria appear to be concentrated within the midbrain tegmentum. This huge mesencephalic nerve cell collection can be subdivided into medial and lateral groups. More caudally, at the level of the isthmic tegmentum, another group of 5-hydroxytryptamine-containing perikarya located close to the midline, within the so-called raphae region, is clearly outlined. The latter group of neurons extends caudally as far as the level of the medulla oblongata. In addition, a small group of catecholamine-containing nerve cell bodies is also found in the ventromedial portion of the rostral midbrain tegmentum, whereas a few other catecholamine type neurons are scattered throughout the lower brain stem of the frog and more especially near the ependymal wall of the fourth ventricle. As a whole, the 5-hydroxytryptamine-containing neuronal systems of the brain stem of Rana temporaria are much more elaborated than the catecholamine neuronal systems of the same structure.

Notes: The guinea pig soleus muscle is a convenient model for the study of slow-twitch intermediate (STI) fiber ultrastructure because it is composed entirely of fibers of this class. Such fibers were compared with fast-twitch red (FTR) and fast-twitch white (FTW) fibers from the vastus lateralis muscle.FTW fibers are characterized by small, sparse mitochondria, a narrow Z line and, an extensive sarcoplasmic reticulum arranged primarily in longitudinal profiles at the A band and with numerous expansions at the I band. Abundant mitochondria with a dense matrix and subsarcolemmal and perinuclear aggregations are typical of FTR fibers. These fibers contain a plexus of sarcoplasmic reticulum at the A band and a less extensive network at the I band. The Z lines are wider (890 ± 74 Å) than those of FTW fibers (582 ± 62 Å). STI intermediate fibers are distinguished from other types by wide Z lines (1205 ± 58 Å), a faint M band, and a less extensive sarcoplasmic reticulum. Compared to FTR fibers, STI fiber mitochondria are usually smaller with less notable subsarcolemmal accumulations.FTW fibers have a more limited capillary supply, rarely contain lipid inclusions, and thus may be restricted to phasic activity. Extensive capillarity, mitochondrial and lipid context, and fast contraction times indicate possible phasic and tonic roles for FTR fibers. STI fibers, characterized by numerous lipid inclusions, extensive capillarity, relatively numerous mitochondria, but slow contraction-relaxation cycles, are morphologically suited for tonic muscle activity.

Notes: The haemocytes of Calpodes ethlius are described with the light and electron microscopes. Five fine structurally distinct types are distinguishable. However only three of these, the granular haemocytes, sphaerule cells and oenocytoids can be positively identified using a series of histochemical stains on smears and on thick sections of araldite-embedded material. The classification is based entirely on the structural features even though several suggestions concerning their function can be made from their fine structure. Intermediates having features of more than one cell type suggest developmental relationships.

Notes: Four hemocyte types have been identified in the late last larval instar of Galleria mellonella. Plasmatocytoids are round to spindle shaped cells, 10-20 μ long and 5-10 μ wide. The cytoplasm contains no distinguishing inclusions. Golgi complexes, rough endoplasmic reticulum and free ribosomes are abundant. Granular hemocytes are oval shaped cells, 10-20 μ long and 5-10 μ wide. The granules, their most characteristic feature, have a diameter of 0.2 μ, a microtubular sub-structure, and are made up of acidic mucosubstances. Lipid droplets may be present in these cells at some stage of development. These cells appear to be phagocytic. Spherule cells are oval shaped, 15-20 μ long and 5-10 μ wide. The spherules, approximately 2 μ in diameter, have a highly ordered substructure and are made up of acidic mucosubstances. Oenocytoids are the largest cells, 20 by 40 μ. The cytoplasm contains mostly free ribosomes and microtubules.

Notes: Formation of secondary palate in hamster was studied with electron microscopy. Prior to assuming horizontal position, the palatal shelves were covered by a two to three cell layer thick epithelium which was separated from the underlying mesenchyme by an intact basal lamina. Epithelial cells were attached to each other by desmosomes. Early hemidesmosomes could be identified as thickenings of the cytoplasmic membrane opposing the basal lamina. Epithelial cells, like other embryonic cells, contained only few organelles but were rich in polyribosomes. As the horizontal shelves approached each other towards the midline, lysosomes and tonofilaments appeared in the superficial and basal cells of the epithelia. Superficial cells showed degeneration and eventual lysis. Fusion of the opposing epithelia occurred between the deeper cells by means of newly formed desmosomes. The epithelial seam resulting from fusion of the epithelia was limited on each side by a continuous basal lamina. Its subsequent thining and eventual fragmentation resulted from the loss of cells by autophagy. There was no evidence of mesenchymal invasion of the epithelial seam. Mesenchymal macrophages appeared in the later stage of palatogenesis and were responsible for phagocytosis of cellular debris.Formation of the soft palate was basically similar to that of the secondary hard palate and occurred by fusion of the opposing shelves. Similarly, anterior closure of the palate occurred by fusion of the lower end of the nasal septum to the primary and secondary palates. Hyperplasia of the opposing epithelia, prior to their fusion, was often seen.It is suggested that formation of the palate occurs in predictable and coordinated fashion and that timely appearance of lysosomes causing lysis of intervening epithelia is of great significance in normal palatogenesis.

Notes: Gross anatomical, histological and histochemical studies of heart development in Mexican salamanders, Ambystoma mexicanum, are reported. Gross observation suggests that heart development in this urodele species is similar to other amphibians. Histological studies in early embryos show the ventromedially migrating sheets of precardiac mesoderm to be composed of two layers of cells. The right and left dorsal layers fuse and give rise to the myocardium, while the ventral layers form the pericardium. The endocardium arises from cells released by the leading edges of the migrating mesoderm mantles. In early myocardial cells, most of the proteins and carbohydrates are contained in yolk platelets; subsequently, these substances become distributed throughout the cytoplasmic matrixes. In early heart cells free lipid droplets are abundant but decline in size and number as development progresses. Concomitantly, there is an increase in bound lipids. Reticular fibers are detected in the endocardial-myocardial spaces simultaneously with trabeculae formation. Collagen appears somewhat later in development.

Notes: The description of the superficial veins of the face and neck was based upon the dissection of 28 male and female adult tufted or brown capuchin monkeys (Cebus apella), captured in southern Goiás, Brazil.Although the venous arrangement of these areas is basically the same in all primates, some characteristic differences were noted: 1. the anterior jugular and common facial veins were absent; 2. most specimens had a venous hyoid arch, and a connecting vessel between the external jugular and subclavian veins; 3. the inferior petrosal sinus drains into the external jugular v. through the postglenoid foramen; 4. the facial, lingual and cephalic veins open into the external jugular vein; 5. both the internal and external jugular veins have about the same diameter; 6. the vascular pattern appears to be quite stable; anatomical variations appear to be few and unimportant.

Notes: The photoreceptors of the adult Anableps anableps have been investigated by light microscopy, scanning and transmission electron microscopy. The fish is a surface swimmer and the eye is divided by the water meniscus. In general, the photoreceptors (rods, single cones, and double equal cones) resemble those of other vertebrates, but there are several unusual features: (1) The outer segment discs of the double cones differ in the two members. (2) All cones have a prominent accessory outer segment derived from the single connecting cilium, and there is no second centriole. (3) The exterior of the inner segments is ridged and grooved longitudinally, most markedly so in the cones. (4) A membranebounded oil droplet is present in the distal cone inner segment, formed from mitochondria which enlarge, fuse and transform in a vitreal-scleral gradient. (5) There are knob-like invaginations of rod cytoplasm into the cones immediately scleral to the external limiting membrane. (6) Subsurface cisterns underlie apposed plasma membranes of double cone inner segments and direct rod-cone inner segment contacts. (7) Fine “fins” on the cones interdigitate, with Müller cell cytoplasm between, just scleral to the external limiting membrane. (8) In the rod spherule there is a greater density of vesicles and the cytoplasm is darker than in the cone pedicle.The well-defined cone mosaic has a linear pattern peripherally and a square pattern centrally. The photoreceptors undergo photomechanical movements. Photoreceptor ultrastructure is alike in both dorsal and ventral parts of the retina, but the ventral retina contains more cells and is thicker than the dorsal retina.The adjustments necessary for simultaneous air and water vision are found mainly in lens shape, corneal thickness and curvature, and the greater number of cells in the ventral retina.

Notes: The ventral pelvic integument of anurans in hypervascular as compared to other skin regions. Recent studies indicate that this area is primarily responsible for water uptake and rehydration. Nine species representing four genera of terrestrial and aquatic Anura were dissected for comparison of vascularity in the pelvic area. Major differences in the ventral pelvic integumental vessels were found between aquatic and terrestrial genera. These variations are described, and names are suggested for previously unnamed vessels. Changes in vascularity are discussed and related to the literature on Anura pertinent to rehydration rates, tolerance of desiccation, resistance to desiccation, and habitat.Data from this study and previous studies suggest a correlation among the parameters discussed and habitat. The suggestion is made that when species are classified as xeric, mesic, or aquatic on the basis of the habitat in which they live, their responses to rehydration, tolerance to desiccation, and vasculatity should be considered, as these characteristics more accurately represent the micro-habitat.

Notes: The development of electric organ spindles of Gymnarchus niloticus has been investigated with respect to the exact time and place of origin and the process of formation of the adult plan. The results are compared with those of Dahlgren ('14). A common primordium for all the electroplates of of a spindle as held by Dahlgren ('14) is not supported by the present work.

Notes: Smooth muscle in the ovaries of estrus and anestrus cats was studied with the TP-Levanol Fast Cyanine 5 RN technique and adrenergic nerves were visualized with the Falck-Hillarp fluorescence procedure. Numerous bundles of smooth muscle fibers were observed in the mesovarium, and the hilar, medullary, and cortical regions of the estrus ovary. Also, theca externa of large vesicular follicles contained many smooth muscle fibers. Adrenergic nerves with varicosities were present in ovarian perifollicular tissue. Anestrus animals had a reduced number of cortical and perifollicular muscle fibers and the intensity and density of fluorescent nerves was reduced. It is suggested that contraction of ovarian smooth muscle facilitates ovulation. These contractions may be, at least partially, under local neural control.

Notes: The effect of hypophysectomy, growth hormone (GH) and an amino acid-glucose mixture on the regenerative ability of the hypophysectomized Triturus pyrrhogaster yielded the following results: 1The survival time of hypophysectomized newts can be prolonged substantially by the sulfamide application.2Although the limb regeneration in the hypophysectomized newt is retarded as compared with that of the pituitary intact control, it finally completes morphogenetic process under such conditions of prolonged survival.3The injection of 100 μg of GH restored the speed of regeneration of pituitary-deprived limbs to almost a normal level.4Injections of the amino acid-glucose mixture also promoted the limb regeneration in hypophysectomized newts. However, initial delay in regeneration to the time of bud appearance was not restored by the nutrients.

Notes: An anatomical analysis of the chicken trigeminal ganglion was made using light microscopy on specimens prepared by usual chemical fixation or freeze-drying methods and by electron microscopy. Two types of neurons were consistently seen, dark and light cells. Dark cells contained a dense cytoplasm with Nissl substance distributed evenly throughout, whereas light cells had a less dense cytoplasm containing clumps of Nissl substance. The Nissl bodies in light cells contained only a few small cisternae of granular endoplasmic reticulum as compared with many stacked cisternae in Nissl bodies of dark cells. The ratio of dark to light cells was approximately 62:38 in all regions of the ganglion. Dark cells were consistently smaller than light cells. In the seven-day old chick, the mean diameters of the dark and light neurons were 21.4 μ and 29.5 μ respectively; in the adult the values were 29.9 μ and 39.7 μ respectively. It is concluded that the dark and light cells belong to two distinct neuronal cell populations.