ALBERT

Description: There is an obvious need for guidelines and standards with respect to what intensities and durations of noise exposure is considered incompatible with the health and well-being of the people exposed. These guidelines would presumably be useful for the zoning of land areas to avoid overexposure of people to environmental noise and for legislative-judicial adjudication of liabilities for possible damages to individuals and groups from exposure to noise. A number of guidelines for noise exposure were promulgated by various governmental agencies for these purposes. Partly because of the need for an integrated and consistent program of noise control for all elements of the government, the United States Environmental Protection Agency (EPA) was established. In addition to previously issuing some specific documents regarding safe noise exposure limits, the EPA joined several Federal operating and regulatory agencies in issuing guidelines for considering noise in land use planning and control. Government guideline documents, as well as some issued by non-government agencies, are examined. Also, newly proposed guidelines for noise in residential areas, and the scientific basis for these guidelines, are presented.

Description: Experience gained through the Shuttle Orbital Flight Test program has matured the engineering understanding of the Shuttle on-orbit control system. The geneology of the control systems (called digital autopilots, or DAPs, and used by the Shuttle for on-orbit operations) is reviewed, the flight experience gained during the flight test program is examined within the context of preflight analysis and test results, and issues for the operational phase of the Shuttle, including constraints upon both operations and analysis still required to increase confidence in the Shuttle's ability to handle capabilities not experienced during the flight test program are addressed. Two orbital autopilots have resulted from computer memory and time constraints on a flight control system, with many different, flight phase unique requirements. The transition DAP, used for insertion and deorbit, has more active sensors and redundancy but a less complex data processing scheme excluding state estimation with fewer choices of operational mode.

Description: The research objective is to clarify the role of aromaticity in the soot nucleation process by determining the relative importance of phenyl radical/molecular oxygen and benzene/atomic oxygen reactions in the complex combustion of aromatic compounds. Three sets of chemical flow reactor experiments have been designed to determine the relative importance of the phenyl radical/molecular oxygen and benzene/atomic oxygen reactions. The essential elements of these experiments are 1) the use of cresols and anisole formed during the high temperature oxidation of toluene as chemical reaction indicators; 2) the in situ photolysis of molecular oxygen to provide an oxygen atom perturbation in the reacting aromatic system; and 3) the high temperature pyrolysis of phenol, the cresols and possibly anisole.

Description: The objective of this research is to record the time histories of the major and minor species which appear in the pyrolysis of toluene, benzene, butadiene, allene, and acetylene; to develop a set of reactions that will model the observed profiles over a wide temperature and concentration range; to identify the critical reactions that influence the pre-particle soot formation process. Toluene and benzene were chosen as two key aromatic compounds which are representative of the pyrolytic process. Butadiene, allene, and acetylene were selected to investigate the formation of aromatic compounds from non-cyclic species. The experimental apparatus used for the study consists of a shock tube coupled to a time-of-flight mass spectrometer Spectra are recorded at 30 microsecond intervals for a total observation time of 0.50 - 1.20 milliseconds. Peak heights of the species of interest in the m/e range 12-300 are measured as a function of reaction time. Calibration curves are constructed which aid the conversion of peak heights to concentrations. The mixtures range from 1 percent-6 percent fuel; the balance is neon diluent.

Description: The goal of this project is to determine the role of the hydroxyl radical during formation of soot. Correlations will be sought between OH concentration and (1) the critical equivalence ratio for incipient soot formation and (2) soot yield as a function of higher equivalence ratios. The ultimate aim is the development of a quasi-global kinetic model for the pre-particulate chemistry leading to soot nucleation. Hydroxyl radical concentration profiles are measured directly in both laminar premixed and diffusion flames using the newly developed technique, laser saturated fluorescence (LSF). This method is capable of measuring OH in the presence of soot particles. Aliphatic and aromatic fuels will be used to assess the influence of fuel type on soot formation. The influence of flame temperature on the critical equivalence ratio and soot yield will be related to changes in the OH concentration profiles. LSF measurements will be augmented with auxiliary measurements of soot and PAH concentrations to allow the development of a quasi-global model for soot formation.

Description: The objective of this research effort is to investigate the gas-phase mechanisms which lead to soot formation in the combustion of complex hydrocarbon fuels. The fuel decomposition is studied under pyrolytic and oxidative conditions behind incident shock waves, using various optical diagnostics to monitor particle appearance and the behavior of gas phase species. In particular, we are investigating: (1) improved quantification of UV/visible soot yield measurements using infrared attenuation and emission techniques; (2) spectral characteristics of gas-phase emission and absorption in the ultraviolet, visible, and infrared; and (3) a conceptual view of the chemical pathways for fuel decomposition and the gas-phase reactions leading to soot formation.

Description: The objective of this research is to investigate the rate limiting chemical mechanisms leading to the formation of soot precursors. A single-pulse shock tube is being used to collect gas samples of stable intermediates and end products of hydrocarbon pyrolysis. These gas samples are analyzed quantitatively using gas chromatography and any mass imbalance is believed to be due to the formation of PAH's and soot. Experimental decomposition rates of the parent hydrocarbon are determined and compared to predictions from the literature. Detailed chemical kinetic mechanisms describing hydrocarbon pyrolysis are being developed and models of soot formation are being compared with the experimental results. Information developed from these pyrolysis studies will provide the fundamental understanding for modeling subsequent oxidation experiments.

Description: In phenotype the mycoplasmas are very different from ordinary bacteria. However, genotypically (i.e., phylogenetically) they are not. On the basis of ribosomal RNA homologies the mycoplasmas belong with the clostridia, and indeed have specific clostridial relatives. Mycoplasmas are, however, unlike almost all other bacteria in the evolutionary characteristics of their ribosomal RNAs. These RNAs contain relatively few of the highly conserved oligonucleotide sequences characteristic of normal eubacterial ribosomal RNAs. This is interpreted to be a reflection of an elevated mutation rate in mycoplasma lines of descent. A general consequence of this would be that the variation associated with a mycoplasma population is augmented both in number and kind, which in turn would lead to an unusual evolutionary course, one unique in all respects. Mycoplasmas, then, are actually tachytelic bacteria. The unusual evolutionary characteristics of their ribosomal RNAs are the imprints of their rapid evolution.

Description: The effect of root-zone temperature on young tomato plants (Lycopersicon esculentum Mill. cv. Heinz 1350) was evaluated in controlled environments using a recirculating solution culture system. Growth rates were measured at root-zone temperatures of 15 degrees, 20 degrees, 25 degrees, and 30 degrees C in a near optimum foliar environment. Optimum growth occurred at 25 degrees to 30 degrees during the first 4 weeks of growth and 20 degrees to 25 degrees during the 5th and 6th weeks. Growth was severely restricted at 15 degrees. Four concentrations of gibberellic acid (GA3) and kinetin were added to the nutrient solution in a separate trial; root-zone temperature was maintained at 15 degrees and 25 degrees. Addition of 15 micromoles GA3 to solutions increased specific leaf area, total leaf area, and dry weight production of plants in both temperature treatments. GA3-induced growth stimulation was greater at 15 degrees than at 25 degrees. GA3 may promote growth by increasing leaf area, enhancing photosynthesis per unit leaf area, or both. Kinetic was not useful in promoting growth at either temperature.

Description: Laboratory experiments to quantify the global production of NOx (NO + NO2) in the troposphere due to atmospheric lightning and biogenic activity in soil are presented. These laboratory experiments, as well as other studies, suggest that the global production of NOx by lightning probably ranges between 2 and 20 MT(N)y-1 of NO and is strongly dependent on the total energy deposited by lightning, a quantity not well-known. In our laboratory experiments, nitrifying micro-organisms is soil were found to be a significant source of both NO and nitrous oxide (N2O). The measured production ratio of NO to N2O averaged 2-3 for oxygen partial pressures of 0.5-10%. Extrapolating these laboratory measurements to the global scale, which is somewhat risky, suggests that nitrifying micro-organisms in soil may account for as much as 10 MT(N) y-1 of NO. Additional experiments with denitrifying micro-organisms gave an NO to N2O production ratio ranging from 2 to 4 for an oxygen partial pressure of 0.5% and a ratio of less than unity for oxygen partial pressures ranging from 1 to 20%. The production of NO and N2O, normalized with respect to micro-organism number indicates that the production of both NO and N2O by denitrifying micro-organisms is at least an order of magnitude less than production by nitrifying micro-organisms for the micro-organisms studied.

Description: A self-consistent method of determining initial conditions for the model presented by Berner, Lasaga, and Garrels (1983) (henceforth, the BLAG model) is derived, based on the assumption that the CO2 geochemical cycle was in steady state at t = -100 my (million years). This initialization procedure leads to a dissolved magnesium concentration higher than that calculated by Berner, Lasaga, and Garrels and to a low ratio of dissolved calcium to bicarbonate prior to 60 my ago. The latter prediction conflicts with the geologic record of evaporite deposits, which requires that this ratio remain greater than 0.5. The contradiction is probably caused by oversimplifications in the BLAG model, such as the neglect of the cycles of organic carbon and sulfur.

Description: A schematic is presented of a simplified electronic architecture of experimental 128 element infrared imager. Tables are given of sample diode responsivity, 512 element focal plane performance summary, and 128 element FPA mechanical and electrical characteristics. Typical 43 x 43 micron detector IV characteristics at 84 K are given, along with typical 43 x 43 micron Indium Antimonide CV characteristic at 83 K.

Description: A personal computer has been used to illustrate physical phenomena and problem solution techniques in engineering classes. According to student evaluations, instruction of concepts was greatly improved through the use of these illustrations. This paper describes the class of phenomena that can be effectively illustrated, the techniques used to create these illustrations, and the techniques used to display the illustrations in regular classrooms and over an instructional TV network. The features of a personal computer required to apply these techniques are listed. The capabilities of some present personal computers are discussed and a forecast of the capabilities of future personal computers is presented.

Description: Motion sickness symptoms, stimuli, and drug therapy are discussed. Autogenic feedback training (AFT) methods of preventing motion sickness are explained. Research with AFT indicates that participants who had AFT could withstand longer periods of Coriolis acceleration, participants with high or low susceptibility to motion sickness could control their symptoms with AFT, AFT for Coriolis acceleration is transferable to other motion sickness stimuli, and most people can learn AFT, though with varying rates of learning.

Description: A diagram is presented for the UCSD low background infrared spot scanner. The spot scanner parameters are outlined. The testing that is planned for the charge injection device is outlined. The Aerojet linear 128 element array is also outlined.

Description: The requirements are diagrammed for the detector array. The configuration choices are given for the row modules and the monolithic layout. The electronic issues are also diagrammed.

Description: A technology program has been underway at Ames since 1978 to develop and evaluate detectors and integrated detector arrays for low-background astronomical applications. The approach is to evaluate existing (less than 24 micron) array technology under low-background conditions, with the aim of adapting and optimizing existing devices. For longer wavelengths, where the technology is much less mature, development is sponsored and devices are evaluated, in both discrete and array formats, for eventual applications. The status of this program has been reported previously. We rely on industrial and university sources for the detectors. Typically, after a brief functionality check in the supplier's laboratory, we work with the device at Ames to characterize its low-background performance. In the case of promising arrays or detectors, we conduct ground-based telescope testing to face the problems associated with real applications. A list of devices tested at Ames is given. In the array category, accumulation-mode charge-injection-devices (AMCIDs) appear repeatedly; this reflects our recent experience with the 2 x 64 and 16 x 16 arrays. Results from the 1 x 16 CID and InSb CCD have been reported. The status of our tests of the discrete Ge:x detectors from Lawrence Berkeley Laboratory are described below. Tests of a 1 x 2 switched sample photoconductor array are just beginning. A 32-channel CMOS multiplexer has been tested at 10 K. Low-temperature silicon MOSFETs and germanium JFETs have also been tested, primarily at Ball Aerospace. This paper describes results to date on three elements of this program: AMCID array, discrete Ge:Ga detectors, and Ge JFET preamplifiers.

Description: An improved 4 to 18 micron array camera system was developed at NASA Goddard SFC for astronomical photometry, using an Aerojet Electro Systems Corp. 16 x 16 Si:Bi accumulation mode charge injection device (AMCID) which could be suitable for eventual low-background spaceflight applications. An astronomical observing program using this device was carried out as a collaboration between NASA Goddard (Infrared and Radio Astronomy Branch and Micro Electronics Branch), the Harvard/Smithsonian Center for Astrophysics, and Steward Observatory of the University of Arizona. In 1983 the camera system was revised, and a new Aeroject Si:Bi array with 16 x 16 active pixels was obtained from NASA/Ames Research Center as part of a new scientific collaboration between the Ames and Goddard infrared array research groups. The 16 x 16 device had sufficiently good sensitivity, uniformity and noise characteristics to be used for successful observations at the Mt. Lemmon 60 and 61 inch telescopes in May 1983. Complete laboratory characterization of the 16 x 16 array was carried out in summer of 1983. Initial results indicate that this detector has sensitivity and noise characteristics comparable to other devices from the same generation of Aerojet arrays.

Description: The topics are presented in view graph form and include the following: an adaptive model following control; adaptive control of a distributed parameter system (DPS) with a finite-dimensional controller; a direct adaptive controller; a closed-loop adaptively controlled DPS; Lyapunov stability; the asymptotic stability of the closed loop; and model control of a simply supported beam.

Description: The first general research objective was to address control design challenges of the Spacecraft Control Laboratory Experiment (SCOLE) via the two stage approach: (1) slew the whole as if it were a rigid body about one Space Shuttle body axis each time using the onboard Reaction Control System (RCS) thrusters; and (2) damp out excited vibrations. The second objective was to examine the feasibility of applying the approach to shuttle-attached flexible space structures. The following was accomplished: (1) a standard bang-bang control technique was adapted; (2) a slew rate limit was imposed in the design; and (3) slew acceleration deviation was defined as the index of slew performance degradation.

Description: Information on a modal model for the Spacecraft Control Laboratory (SCOLE) is given in viewgraph form. A partial differential equation model covering roll bending, pitch bending, torsion, shear forces, and bending moments is given.

Description: The distributed element dynamic analysis package DISTEL is used to analyze the NASA/Institute of Electrical and Electronics Engineers' Spacecraft Control Laboratory Experiment (SCOLE). In this configuration, the Space Shuttle motion is coupled to the motion of a large dish antenna through a Shuttle-deployed flexible mast of 40 m long. Due to the high asymmetry of the system, the motions about the different axes (roll, pitch, yaw) are severely coupled. A general purpose software like DISTEL is especially suited for this kind of analysis. Modal frequencies of the complete spacecraft and impulse response (modal gains) to excitations at different locations are obtained. Mode-shape plots of the deformations of the entire system are given. Finally, results obtained at NASA and at Purdue University are compared to those found by the European space technology center, ESTEC.

Description: A mathematical formulation for the control of the Spacecraft Control Laboratory Experiment (SCOLE) configuration is given. Two equivalent approaches, one using a functional equation and the other an abstract wave equation, are illustrated. Such a formulation can help in digital computer simulation to evaluate control laws, providing insight, and generating control laws.

Description: The most straightforward way of reducing the noise equivalent power of bolometers is to lower their operating temperature. We have been exploring the possibility of using conventionally constructed bolometers at ultra-low temperatures to achieve NEP's suitable to the background environment of cooled space telescopes. We have chosen the technique of adiabatic demagnetization of a paramagnetic salt as a gravity independent, compact, and low power way to achieve temperatures below pumped He-3 (0.3 K). The demagnetization cryostat we used was capable of reaching temperatures below 0.08 K using Chromium Potassium Alum as a salt from a starting temperature of 1.5 K and a starting magnetic field of 30,000 gauss. Computer control of the magnetic field decay allowed a temperature of 0.2 K to be maintained to within 0.5 mK over a time period exceeding 14 hours. The refrigerator duty cycle was over 90 percent at this temperature. The success of these tests has motivated us to construct a more compact portable adiabatic demagnetization cryostat capable of bolometer optical tests and use at the 5m Hale telescope at 1mm wavelengths.

Description: Some conclusions reached are as follow. Neutron Transmutation Doping (NTD) of high quality Ge single crystals provides perfect control of doping concentration and uniformity. The resistivity can be tailored to any given bolometer operating temperature down to 0.1 K and probably lower. The excellent uniformity is advantaged for detector array development.

Description: Some advantages are given of the basic AMCID configuration. The spectral response is diagrammed of doped silicon detectors.

Description: Bolometers operating at low temperatures (T greater than 0.3 K) are the best candidate for far infrared (lambda greater than or = 120 microns) and submillimeter detection from cold orbiting telescopes. The limits of sensitivity for such devices have been studied (Mather, 1983). Based on this work, we conclude that excellent sensitivity is possible given careful detector design. We have designed and are fabricating bolometers for operation at low temperatures. The crucial components in detector design are (1) heat capacity, (2) temperature sensing, and (3) absorption of infrared radiation. In this presentation, we discuss the choice of materials and fabrication techniques we have made in the interest of maximum sensitivity. In order that optimization of detector performance be reasonably easy to carry out, we have attempted to use conventional fabrication techniques wherever possible (photolithography, wire bonding). The use of such procedures allows us to make design changes on short time scales, which is essential in achieving optimal performance.

Description: Some conclusions reached are as follow. Ge:Be detectors provide lower Noise Equivalent Power (NEP) and higher responsivities than state of the art Ge:Ga detectors at 42 microns. Reliable Be doping was achieved with Czochralski growth from a carbon susceptor under vacuum. The photoconductive behavior of Ge:Be detectors is strongly influenced by the concentration of residual shallow impurities. Optimization of Ge:Be detectors requires both a low concentration and precise compensation of shallow acceptors.

Description: The objectives of this study are listed as follows: (1) to develop Lagrange's equations of motion for the shuttle antenna configuration in orbit; (2) to modify equations using the Lagrange multiplier method to develop equations of motion for the laboratory experiment; and (3) to discuss methods for simulation and control. The equations are presented in graph form.

Description: Discussed here is a NASA program which was initiated to make direct comparisons of control laws for a mathematical problem. An experimental test item is being assembled under the cognizance of the Spacecraft Control Branch at Langley Research Center. The physical apparatus will consist of a softly supported dynamic model of an antenna attached to the Space Shuttle by a flexible beam. The control objective will include the task of directing the line of sight of the Shuttle/antenna configuration toward a fixed target, under conditions of noisy data, limited control authority, and random disturbances.

Description: The scope of this study covered steady-state, continuous-time vibration control under disturbances applied to the Space Shuttle and continuous-time models of actuators, sensors, and disturbances. Focus was on a clear illustration of the methodology, therefore sensor/actuator dynamics were initially ignored, and a finite element model of the NASA Spacecraft Control Laboratory Experiment (SCOLE) was conducted, including products of inertia and offset of reflector CM from the mast tip.

Description: The motivation was to develop a control design and analysis methodology directly applicable to design concepts of flexible spacecraft of interest the the U.S. Navy and to provide a testbed for the evaluation of large space structure control techniques developed at the Naval Research Laboratory. The topics covered include the following: (1) a list of key concepts; (2) evaluation of the Spacecraft Control Laboratory Experiment (SCOLE) model with DISCOS; (3) baseline results, line of sight error vs. time; (4) general formulation of optimization; (5) geometric interpretation, projected eigenaxis; (6) closed loop control law; and (7) future directions.

Description: Nonlinear and linear equations of motions were derived. The preliminary investigation consisted of model beam as truss structure, effects of truss structure on control design, and effects of reflector offset on control design. It was concluded that the offset of the reflector c.g. from the beam reflector attach point is dynamically significant. Also, truss effects may also significantly effect the performance of the controller if ignored. If the truss is included in the modeling of the NASA/SCOLE configuration, a practically implementable scheme is available to reduce the model order.

Description: The Spacecraft Control Laboratory Experiment (SCOLE) will allow direct experimental comparison of competing control schemes for large flexible spacecraft structures. The experiment was designed to emulate the essential characteristics of a mathematical model design challenge which represents a Space Shuttle with a flexible mast and antenna attached. This experiment represents the third in a series of three flexible structure control experiments used by the Flight Dynamics and Control Division at LaRC. The key problem addressed by the facility is that flexible motion of the mast and antenna must be considered in the slewing and pointing control problems.

Description: The following topics are covered in view graph form: (1) pulse control strategy; (2) stability analysis and digital simulations; (3) digital/analog and analog/digital conversions, and analog simulation; and (4) experimental studies.

Description: Researchers simplified the analytical expression of the line of sight (LOS) error, discovered and proved the independence of Euler angle Psi, calculated attitude angles corresponding to 0 degrees and 20 degrees LOS errors, determined choices of initial alignment, tailored the slew maneuvers for LOS pointing, simulated numerically the LOS pointing slew of the Spacecraft Control Laboratory Experiment (SCOLE), and evaluated the pointing performance.

Description: Projections of technological advances to the year 2000 have suggested a number of possible conceptual types of air vehicles. For convenience, these have been grouped according to speed, increasing from below Mach 1 (including hovering flight) through various Mach ranges to orbital flight. The potential performance capabilities that could be realized for each of these types of aircraft provide exciting prospects for the years beyond 2000. It is clear that the greater design flexibilities provided by the projected technology advances will permit significant improvements in performance, economy, and safety and allow the design and development of aircraft systems that current technology will not support. In the following sections, each vehicle type is discussed, noting design features and significant advances. Where related aircraft exist, the significant economic and performance factors are compared. In addition, for each concept, the technology developments considered essential for the advanced concept are identified. The types of aircraft described are examples of what advances in the technology projected for the year 2000 could provide. They are by no means all that would be possible. The panel's views on the current state of knowledge of systems intergration as a discipline and the need for advancement in this area presented in the concluding section of this report.

Description: Over the last 50 years, aeronautical structures have evolved from the wood, fabric, and wire of low-speed biplanes to supersonic aircraft fabricated with advanced metallic and nonmetallic materials. The advances made in structures technology have had significant impact on aircraft design and performance. An example is the large weight reductions being realized from the utilization of composite materials for secondary and primary structures. However, structural advances have been evolutionary, not revolutionary. Through the year 2000, there are opportunities to obtain significant new advancements in structural technology. These advances could result in considerable performance and capability payoffs such as increased payload, range, speed, maneuverability, fuel efficiency, and safety through reductions in weight, increases in strength, and the ability to make structures pliable. Also, with new manufacturing processes it is possible that reductions in production costs will be realized. Some of the structural technology areas where future major advances could be made are adaptive structures, thermal structures, damage tolerant structures, propulsion system structures, and new structural concepts.

Description: Progress in aerodynamics over the past 50 years has been evidenced by the development of increasingly sophisticated and efficient flight vehicles throughout the flight spectrum. Advances have generally arisen in an evolutionary manner from experience gained in wind tunnel testing, flight testing, and improvements in analytical and computational capabilities. As a result of this evolutionary development, both military and commercial vehicles operate at a relatively high efficiency level. This observation plus the fact that airplanes have not changed appreciably in outward appearance over recent years has led some skeptics to conclude incorrectly that aerodynamics is a mature technology, with little to be gained from further developments in the field. It is of interest to note that progress in aerodynamics has occurred without a thorough understanding of the fundamental physics of flow, turbulence, vortex dynamics, and separated flow, for example. The present understanding of transition, turbulence, and boundary layer separation is actually very limited. However, these fundamental flow phenomena provide the key to reducing the viscous drag of aircraft. Drag reduction provides the greatest potential for increased flight efficiency from the standpoint of both saving energy and maximizing performance. Recent advances have led to innovative concepts for reducing turbulent friction drag by modifying the turbulent structure within the boundary layer. Further advances in this basic area should lead to methods for reducing skin friction drag significantly. The current challenges for military aircraft open entirely new fields of investigation for the aerodynamicist. The ability through very high speed information processing technology to totally integrate the flight and propulsion controls can permit an aircraft to fly with "complete abandon," avoiding departure, buffet, and other undesirable characteristics. To utilize these new control concepts, complex aerodynamic phenomena will have to be understood, predicted, and controlled. Current requirements for military aircraft include configuration optimization through a widened envelope from subsonic to supersonic and from low to high angles of attack. This task is further complicated by requirements for control of observables. These challenging new designs do not have the luxury of a large experimental data base from which to optimize for various parameter combinations. Consequently, there exists a strong need for better techniques, both experimental and computational, to permit design optimization in a complete sense.

Description: Propulsion, while conventionally included on the list of important aeronautical disciplines along with aerodynamics, structures, etc., is in itself a systems endeavor, analogous to the engineering of the entire vehicle; indeed propulsion encompasses important aspects of all the other disciplines. In recognition of this fact, the panel focused its discussion on those aspects of the key disciplines that are especially or uniquely important to propulsion. From the initial development of the airplane, the propulsion system has been recognized as one of the pacing technologies. It is perhaps because of the technological disparity between the reciprocating engine and the primitive airframe that the two remained relatively and separate, were developed somewhat independently, usually by different organizations. In recent years, the maturing of the gas turbine power plant and the advance in high-speed airframes have rendered this separation somewhat artificial. The power plant and the airframe now share common structural and aerodynamic elements; as the flight Mach number rises, the degree of interaction increases. By the year 2000, this interdependence will have increased in many respects to a point where independent design may not be practical or possible. During the period since the initiation of the aircraft gas turbine, the solid propellant rocket and the liquid propellant rocket, a vast array of other novel engines have been studied, covering the full spectrum of flight conditions from low subsonic to hypersonic and transatmospheric flight. In each instance, performance limits have been investigated under the assumption that current technology or reasonably foreseeable technology would be available for their development. Among the extensive list of advanced, high-performance concepts and cycles examined are the hypersonic ramjet, the variable cycle, runway-to-orbit airbreathing engine, the ram rocket (airbreathing and rich solid propellant rocket), and the air turborocket. At various times, these systems have come relatively close to meriting development and application. In many instances, limitations of materials and technologies curtailed development. As important and with almost equal frequency, the lack of commercial or military utility of the concept precluded the necessary funding. It is instructive to note that two former items on this list, the turbofan (bypass engine) and the high-speed turboprop, are respectively a mainstay engine and a promising development. In the case of the turbofan, its full potential could not be realized until turbine cooling technology had been developed and new materials developed to permit the construction of transonic fans. In the case of the highspeed turbopropeller engine, not only were the material and turbine technologies needed, but, in addition, the rise in fuel costs provided the impetus to take advantage of its favorable fuel consumption characteristic. As the basic technologies progress and as new missions become attractive, the engines in the foregoing list become candidates for new feasibility studies and further technology development. At the present time, the ram rocket is the prime contender to augment the range of small missiles. Of interest also is the hypersonic ram jet and its logical extension, the runway-to-orbit airbreathing engine. Much of this report deals with the development of current or near-future power plant concepts. First, the motivating factors for aeronautical propulsion research are reviewed as a reminder of the importance of continued effort in a field that has often been characterized as mature. Next, technical areas are discussed in which the panel feels additional research effort is warranted and would lead to the realization of the technological potentials between now and the year 2000. Under these guidelines, new cycles (e.g., isothermal energy exchange) were not considered by the panel. Finally, although facility requirements were not a prime consideration in the current projections, the panel believes that the increasing complexity of propulsion systems; the need for more refined interaction between propulsion system, airframe, and controls; and increasing operation in adverse weather will require test capabilities beyond those now available (see appendix). Enhanced test capability is needed in the areas of propulsion airframe integration and in largescale icing research with proper concurrent treatment of altitude, temperature, and speed.

Description: Guidance, navigation, and control (GNC) systems have historically been vital to improving operational capability of aircraft. The development of autopilots and electronic navigation systems has greatly aided the crew in flying precise routes in all weather conditions while at the same time reducing pilot workload. Advances in high-integrity onboard computing and electronics technology have resulted in a significant increase in the capability of these subsystems to perform more reliably, efficiently, and safely. Onboard computing and control system capability has provided new design approaches for the aircraft designer. By using automatic control systems to stabilize the aircraft, the designer can relax certain conventional aerodynamic stability requirements and achieve aircraft performance benefits. Thus, modern fighter aircraft are designed with low levels, or in fact, negative levels of longitudinal static stability to boost maneuvering capability and cruise performance, relying on the use of full-time, full-authority automatic stability augmentation systems to stabilize the aircraft. During the next 20 years, GNC systems will become a driving force in aircraft design. Instead of making separately designed major aircraft systems work together, the designer will exploit the interaction and integration of aerodynamic, structural, and propulsion system controls to provide a better aircraft. The benefits of such integrated designs have been demonstrated already. Integrated digital control of the engine inlet and autopilot systems on a NASA YF-12 research aircraft resulted in a range increase of 7 percent. A civil transport derivative using extensions on each wing and an active control system to minimize the requirement for structural modifications achieved significant cruise performance improvements. These are first-generation applications of advanced GNC systems. More significant benefits are achievable by the year 2000. Complete integration of aerodynamic, propulsion and structural controls, and mission avionics will provide dramatically better aircraft performance, new capability (low observability, supermaneuverability) and/or improved mission effectiveness. This requires a concurrent, multidisciplinary design approach early in the design stage. The role of advanced GNC systems in future aircraft is not an option.

Description: Materials and manufacturing technology are critical to advanced aircraft and permeate all disciplines. Current aircraft systems employ a variety of materials, each selected to provide the best vehicle design in terms of performance, safety, reliability, manufacturability, and life cycle cost. However, a mistake in materials selection could bankrupt an airframe or engine manufacturer. Thus, the introduction of new materials is a slow process. Generally, new materials are used initially in noncritical components until their performance in service can be confirmed. Then, as confidence grows, they are used in more and more critical applications. Finally, if appropriate, new materials are used in critical, static elements and then in dynamic components. Thus, because the nominal time for development of a conventional monolithic material ranges from 5 to 10 years there is a 10- to 15- year lag between laboratory effort and introduction into service. Therefore, to assure the availability of materials suitable for production aircraft and engines in the year 2000, the concepts already must have been identified and must be progressing along evolutionary paths toward application. Trends, actual and projected, in the use of materials for commercial engines are shown in Figure 4-1. Related military applications are projected to follow similar paths. The new actor will be composites. The panel examined a wide range of materials important to all aspects of aircraft development, airframe structures, propulsion systems and for other important aircraft subsystems. These are addressed in the body of the report in terms of the current state of the art, opportunities for improvement, and barriers to achievement of projected benefits. This is followed by projections of the progress of technology that could be realized by the year 2000 with the application of appropriate resources.

Description: The structural analysis of the Space Shuttle orbiter was planned with two concepts in mind: use derivatives or subsets of the same basic finite element model whenever feasible, and substantiate the model's predictive capability by performing ground tests. The analysis cycle (model modal loads stress (MMLS)) starts with the finite element model conception and ends with the detailed stress analysis and margins of safety. The structural analysis of the orbiter encompasses a variety of static and dynamic problems. The salient features of these problems and their solutions are examined.

Description: The governing equations for the analysis of open branch-chain mechanical systems are developed in a form suitable for implementation in a general purpose finite element computer program. Lagrange's form of d'Alembert's principle is used to derive the system mass matrix and force vector. The generalized coordinates are selected as the unconstrained relative degrees of freedom giving the position and orientation of each slave link with respect to their master link. Each slave link may have from zero to six degrees of freedom relative to the reference frames of its master link. A strategy for automatic generation of the system mass matrix and force vector is described.

Description: In many structures the final stress states are dependent on the sequence of construction or the stress states at various stages of construction are of interest. Such problems can be analyzed using finite element programs that have the capability of adding (birthing) elements to simulate the progress of construction. However, the usual procedure of assembling elements may lead to numerical instabilities or stress states that are unrealistic. Both problems are demonstrated in the analysis of a structure using the program ADINA. A technique which combines application of a preload with element birthing to overcome these problems is described and illustrated.

Description: A technique utilizing finite element analysis, liquid impact kinematics, and momentum theory is described and compared to single-drop impact test data performed on various configurations of coated ceramic material. The method correlates well with test data and is useful in predicting the single-drop impact damage velocity threshold for low-density, coated ceramic materials.

Description: An algorithm is outlined for simulating the contact surface erosion for impact problems. The algorithm dynamically relocates the contact surface as projectile and target materials exceed their failure criterion. Example computations of axisymmetric and oblique impacts are compared with experimental data.

Description: Transport fuselage section drop tests provided useful information about the crash behavior of metal aircraft in preparation for a full-scale Boeing 720 controlled impact demonstration (CID). The fuselage sections have also provided an operational test environment for the data acquisition system designed for the CID test, and data for analysis and correlation with the DYCAST nonlinear finite-element program. The correlation of the DYCAST section model predictions was quite good for the total fuselage crushing deflection (22 to 24 inches predicted versus 24 to 26 inches measured), floor deformation, and accelerations for the floor and fuselage. The DYCAST seat and occupant model was adequate to approximate dynamic loading to the floor, but a more sophisticated model would be required for good correlation with dummy accelerations. Although a full-section model using only finite elements for the subfloor was desirable, constraints of time and computer resources limited the finite-element subfloor model to a two-frame model. Results from the two-frame model indicate that DYCAST can provide excellent correlation with experimental crash behavior of fuselage structure with a minimum of empirical force-deflection data representing structure in the analytical model.

Description: The dynamic behavior of aircraft fuselage structures subject to various impact conditions was investigated. An analytical model was developed based on a self-consistent finite element (CFE) formulation utilizing shell, curved beam, and stringer type elements. Equations of motion were formulated and linearized (i.e., for small displacements), although material nonlinearity was retained to treat local plastic deformation. The equations were solved using the implicit Newmark-Beta method with a frontal solver routine. Stiffened aluminum fuselage models were also tested in free flight using the UTIAS pendulum crash test facility. Data were obtained on dynamic strains, g-loads, and transient deformations (using high speed photography in the latter case) during the impact process. Correlations between tests and predicted results are presented, together with computer graphics, based on the CFE model. These results include level and oblique angle impacts as well as the free-flight crash test. Comparisons with a hybrid, lumped mass finite element computer model demonstrate that the CFE formulation provides the test overall agreement with impact test data for comparable computing costs.

Description: A study of the dynamic characteristics of a coupled translational-rotational system is given. The formulation of the problem considers the soil-structure interaction effects by utilizing the impedance functions at the foundation of a structure. Due to the fact that the coefficient matrix in the characteristic equation is frequency dependent in nature, iterations have to be performed to find the nature frequencies of the system. Examples and discussions are presented. Comparisons of the analytical results from various approaches are also given.

Description: Two analytical techniques applicable to large deflection dynamic response calculations for pressure loaded composite sandwich panels are demonstrated. One technique utilizes finite element modeling with a single equivalent layer representing the face sheets and core. The other technique utilizes the modal analysis computer code DEPROP which was recently modified to include transverse shear deformation in a core layer. The example problem consists of a simply supported rectangular sandwich panel. Included are comparisons of linear and nonlinear static response calculations, in addition to dynamic response calculations.

Description: The design of thin shell structures with respect to elastoplastic buckling requires an extended analysis of the influence of initial imperfections. For conservative design, the most critical defect should be assumed with the maximum allowable magnitude. This defect is closely related to the initial postbuckling behavior. An algorithm is given for the quasi-static analysis of the postbuckling behavior of structures that exhibit multiple buckling points. the algorithm based upon an energy criterion allows the computation of the critical perturbation which will be employed for the definition of the critical defect. For computational efficiency, the algorithm uses the reduced basis technique with automatic update of the modal basis. The method is applied to the axisymmetric buckling of cylindrical shells under axial compression, and conclusions are given for future research.

Description: A general approach is required for describing matter of behavior when the failure is likely to involve growth and coalescence of a large number of fractures. Failures of this kind appear frequently in rapid dynamic processes, particularly in the formation of spall fragments. An approach to formulating constitutive relations that accounts for the opening, shear and growth of an ensemble of cracks is discussed. The approach accounts for plastic flow accompanying fragmentation. The resulting constitutive relations were incorporated into a Lagrangian computer program. A theoretical approach to coalescence is described. The simplest formulation uses a linear Liouville equation, with crack growth limited by the mean free path of cracks, assumed constant. This approach allows for an anisotropic distribution of cracks. An alternative approach in which the decrease of the mean free path with increasing crack size is accounted for, but the crack distribution is assumed isotropic is described. A reduction of the governing Liouville equation to an ordinary differential equation of third order is possible, and the result can be used to determine how mean free path decreases with increasing crack size.

Description: The design of a composite panel requires some way of finding the minimum thickness laminate which will withstand the load requirements without failure. The mathematical complexity of this problem dictates the use of nonlinear optimization techniques. Specialized laminate optimization programs were developed which are compact and efficient enough to run on microcomputers. Only stresses at a point and inplane loads and deflections are considered. The programs are simple to use and require no knowledge of optimization. Techniques are developed which find minimum thickness laminates with either ply ratios or ply angles as design variables. A method is presented for finding the optimum orientation for the axis of symmetry of an orthotropic laminate. The orthotropic laminate program uses an approximate failure theory, which speed up computations dramatically.

Description: The evaluation of the total probability of a plastic collapse failure P sub f for a highly redundant structure of random interdependent plastic moments acted on by random interdepedent loads is a difficult and computationally very costly process. The evaluation of reasonable bounds to this probability requires the use of second moment algebra which involves man statistical parameters. A computer program which selects the best strategy for minimizing the interval between upper and lower bounds of P sub f is now in its final stage of development. The relative importance of various uncertainties involved in the computational process on the resulting bounds of P sub f, sensitivity is analyzed. Response sensitivities for both mode and system reliability of an ideal plastic portal frame are shown.

Description: A finite element modeling technique which utilizes a triangular element called TSHEL with 45 degrees of freedom and seven point integration was tested for analysis of thin plate and shell structures. The element formulation is based on the degenerate solid shell concept and the mixed formulation with assumed independent inplane and transverse shear strains. The effectiveness of the present modeling technique which features combined use of elements with kinematic modes and those without kinematic modes to eliminate both locking and spurious kinematic modes at the global structural levels are shown.

Description: The stress derivative technique for control of keystoning deformation in under-integrated finte elements is based on expansion of the stress in a Taylor series about the element center and retention of additional terms beyond the constant stress term. It has the advantage over other control techniques that keystoning resistance is provided by actual rather than artificial material properties. Application of this technique to the quadrilateral ring elements used for modelling solids of revolution subjected to axisymmetric loads is described. In a cylindrical coordinate system additional terms appear in the formulation which must be dealt with in arriving at a workable keystoning control scheme.

Description: A relational database management system is presented that is tailored for engineering applications. A wide variety of engineering data types are supported and the data definition language (DDL) and data manipulation language (DML) are extended to handle matrices. The system can be used either in the standalone mode or through a FORTRAN or PASCAL application program. The query language is of the relational calculus type and allows the user to store, retrieve, update and delete tuples from relations. The relational operations including union, intersect and differ facilitate creation of temporary relations that can be used for manipulating information in a powerful manner. Sample applications are shown to illustrate the creation of data through a FORTRAN program and data manipulation using the TEQUEL DML.

Description: An existing program is currently being adapted to perform finite element analysis by distributing substructures over a network of four Apple IIe microcomputers connected to a shared disk. In this network, one microcomputer controls the entire process while the others perform the analysis on each substructure in parallel. This substructure analysis is used in an iterative, fully stressed, structural resizing procedure. This procedure allows experimentatation with resizing in which all analyses are not completed during a single iteration. This research gives some insight on how to configure multidiscriplinary analysis and optimization procedures for decomposable engineering systems using either high performance engineering workstations or a parallel processor supercomputer. In addition, the operational experience gained facilitates the implementation of analysis programs on these new computers when they become available in an engineering environment.

Description: Described are the experiences gained from solving for the dynamic response of two simple structures on an experimental Multiple Instruction Multiple Data (MIMD) computer called the finite element machine. Introduced are MIMD computing concepts, describing how the concurrent algorithmic techniques implemented and giving results for the two example problems. The results show computational speedups of up to 7.83 using eight of the finite element machine processors and indicate that significant computational speedups are possible for large order structural computations.

Description: The FLEX/32 Multicomputer is a generic environment for cooperating multiple processors. The FLEX/32 supports a number of different processors, making it heterogeneous in terms of the instruction sets it supports, and homogeneous in its ability to provide consistent storage and input/output facilities to its differing processors. These facilities are accessed through standard 32-bit VMEbus connections. The FLEX/32 supports the full UNIX System V Operating System and languages associated with it, plus the extended ConCurrent C and Concurrent FORTRAN 77 languages that allow programming of concurrent software at a high level. Direct programming support at all levels is provided by the environment hardware for concurrent software execution and optimization, including hardware support for shared resource access arbitration, conditional critical region arbitration, and interprocessor messages.

Description: Research aimed at faster, more cost effective parallel machines and algorithms for improving designer productivity with finite element computations is discussed. A set of 8 boards, containing 4 nearest neighbor connected arrays of commercially available floating point chips and substantial memory, are inserted into a commercially available machine. One-tenth Mflop (64 bit operation) processors provide an 89% efficiency when solving the equations arising in a finite element problem for a single variable regular grid of size 40 by 40 by 40. This is approximately 15 to 20 times faster than a much more expensive machine such as a VAX 11/780 used in double precision. The efficiency falls off as faster or more processors are envisaged because communication times become dominant. A novel successive overrelaxation algorithm which uses cyclic reduction in order to permit data transfer and computation to overlap in time is proposed.

Description: Most of the research on reactions of people to community noise is divided into studies of annoyance as measured by attitude surveys and annoyance as measured by complaint behavior, including legal actions. This research has provided means of testing the concept promulgated over 20 years ago that the average amount of noise energy from significant sources that intrudes daily into houses and living areas can be used to predict the impact of the noise on people in a community. However, research data on annoyance and complaint behavior collected over the past 10 to 20 years have shown that there are significant limitations and variables that must be considered in the fair application of the noise energy concept in its simplest form.

Description: The establishment of a baseline of normal hearing is investigated through the examination of pure tone hearing level surveys and variables such as age, sociocusis, sex, race, and otological disorders. Mathematical formulae used to predict hearing levels in industrial and nonindustrial surveys is included.

Description: Voyager 1 images show 14 volcanic centers wholly or partly within the Kane Patera quadrangle of Io, which are divided into four major classes: (1) shield with parallel flows; (2) shield with early radial fan shapd flows; (3) shield with radial fan shaped flows, surfaces of flows textured with longitudinal ridges; and (4) depression surrounded by plateau-forming scarp-bounded, untextured deposits. The interpretation attempted here hinges largely on the ability to distinguish lava flows from pyroclastic flows by remote sensing.

Description: Large flexible communication satellite controller design is considered. The satellite that was developed for a "straw man' was configured as an offset fed paraboloid with a set of masts and booms that carry the antenna. The controllers were both a boom and mast actuator and a set of two degree of freedom actuators at the antenna to move it in order to satisfy both line of sight and defocus control.

Description: Opinions conflict over the role of surface gravity in shaping impact craters on Mercury. One view holds that the effects of g are evident in measurable aspects of crater form; other investigators find little or no evidence for g's geomorphic importance. Ambiguity in the role of g and other variables in cratering on Mercury stems largely from uncertainty in identifying major geomorphic contrasts and the crater sizes at which they occur. One of these, depth/diameter (d/D), undergoes a major change at the transition from simple (bowl shaped) to complex (peaks and terraces) crater interiors. Four least-squares d/D fits for fresh craters on Mercury were attemped. The results are inconsistent. The d/D data that should resolve previous shortcomings is presented. The revised d/D distributions for simple and complex craters, which intersect at a diameter of about 5 km, support the initial thesis that g substantially influences the form of Mercury's craters.