ALBERT

Description: Several electromagnetic signal types were observed prior to and immediately after 30 October 2007 (Local Time) M5.4 earthquake at Alum Rock, Ca with an epicenter ~15 km NE of San Jose Ca. The area where this event occurred had been monitored since November 2005 by a QuakeFinder magnetometer site, unit 609, 2 km from the epicenter. This instrument is one of 53 stations of the QuakeFinder (QF) California Magnetometer Network-CalMagNet. This station included an ultra low frequency (ULF) 3-axis induction magnetometer, a simple air conductivity sensor to measure relative airborne ion concentrations, and a geophone to identify the arrival of the P-wave from an earthquake. Similar in frequency content to the increased ULF activity reported two weeks prior to the Loma Prieta M7.0 quake in 1989 (Fraser-Smith, 1990, 1991), the QF station detected activity in the 0.01–12 Hz bands, but it consisted of an increasing number of short duration (1 to 30 s duration) pulsations. The pulsations peaked around 13 days prior to the event. The amplitudes of the pulses were strong, (3–20 nT), compared to the average ambient noise at the site, (10–250 pT), which included a component arising from the Bay Area Rapid Transit (BART) operations. The QF station also detected different pulse shapes, e.g. negative or positive only polarity, with some pulses including a combination of positive and negative. Typical pulse counts over the previous year ranged from 0–15 per day, while the count rose to 176 (east-west channel) on 17 October, 13 days prior to the quake. The air conductivity sensor saturated for over 14 h during the night and morning prior to the quake, which occurred at 20:29 LT. Anomalous IR signatures were also observed in the general area, within 50 km of the epicenter, during the 2 weeks prior to the quake. These three simultaneous EM phenomena were compared with data collected over a 1–2-year period at the site. The data was also compared against accounts of air ionization reported to be associated with radon emission from the ground (Ouzounov, 2007), and a series of laboratory rock stressing experiments (Freund, 2006, 2007a, b, c) to determine if field data was consistent either of these accounts. We could not find a data set with pre-earthquake radon measurements taken near the Alum Rock epicenter to compare against our field data. However, based on the Alum Rock data set example and another data set at Parkfield, the field tests are at least consistent with the lab experiments showing currents, magnetic field disturbances, air conductivity changes, and IR signatures. This is encouraging, but more instrumented earthquake examples are needed to prove a repeating pattern for these types of pre-earthquake EM signatures. For more information on QuakeFinder please view http://www.quakefinder.com.

Description: To study the effect of stress-activated positive hole (p-hole) charge carriers on the infrared (IR) emission from rocks, we subjected a portion (~10 vol.%) of a large (60×30×7.5 cm3) block of anorthosite, a nearly monomineralic (Ca-rich feldspar) igneous rock, to uniaxial deviatory stress up to failure. We measured the IR emission from a flat surface ≈40 cm from the stressed rock volume over the 800–1300 cm−1 (7.7–12.5 μm) range. Upon loading, the intensity and spectrum of the IR emission change. Narrow bands near instantly appear at 930 cm−1 (10.75 μm), 880 cm−1 (11.36 μm), 820 cm−1 (12.4 μm) plus additional bands in the 1000–1300 cm−1 (10.0–7.7 μm) range. Upon further loading the bands broaden and shift. Their intensities increase but also fluctuate. Near the emission maxima at 300 K, at 1150 cm−1 and 1030 cm−1 (8.7 and 9 μm), barely any intensity increase occurs suggesting that the temperature of the surface does not actually increase. We propose that the observed narrow IR emission bands arise from vibrationally excited O-O stretching modes which form when p-hole charge carriers (activated in the stressed rock) spread into the unstressed portion of the rock to the surface, where they recombine and radiatively decay. The effect, stimulated IR emission due to hole-hole recombination, may help explain the enhanced IR emission seen in night-time satellite images of the land surface before major earthquakes known as "thermal anomalies''.

Description: To study the effect of stress-activated positive hole (p-hole) charge carriers on the infrared (IR) emission from rocks, we subjected a portion (~10 vol.%) of a large (30×60×7.5 cm3) block of anorthosite, a nearly monomineralic (Ca-rich feldspar) igneous rock, to uniaxial deviatory stress up to failure. We measured the IR emission from a flat surface ≈40 cm from the stressed rock volume over the 800–1300 cm−1 (7.7–12.5 μm) range. Instantly, upon loading, the emission spectrum and intensity change. At first narrow bands appear at 930 cm−1 (10.75 μm), 880 cm−1 (11.36 μm), 820 cm−1 (12.4 μm) plus additional narrow bands in the 1000–1300 cm−1 (7.7–10.0 μm) range. The 10.75–12.4 μm bands are thought to arise from vibrationally excited O-O stretching modes, which form when p-hole charge carriers, which spread from the stressed rock volume into the unstressed rock, recombine at the surface. They radiatively decay, giving rise to "hot" bands due to transitions between excited states. Before failure the broad emission bands at 1170 cm−1 and 1030 cm−1 (8.7 and 9.7 μm) also increase slightly in intensity, suggesting a small increase in temperature due to thermalization of the energy deposited into the surface through p-hole recombination. Stimulated IR emission due to hole-hole recombination and its follow-on effects may help understand the enhanced IR emission seen in night-time satellite images of the land surface before major earthquakes known as "thermal anomalies".

Description: Performance requirements regarding geometric accuracy have been defined in terms of end product goals, but until recently no precise details have been given concerning the conditions under which that accuracy is to be achieved. In order to achieve higher spatial and spectral resolutions, the Thematic Mapper (TM) sensor was designed to image in both forward and reverse mirror sweeps in two separate focal planes. Both hardware and software have been augmented and changed during the course of the Landsat TM developments to achieve improved geometric accuracy. An investigation has been conducted to determine if the TM meets the National Map Accuracy Standards for geometric accuracy at larger scales. It was found that TM imagery, in terms of geometry, has come close to, and in some cases exceeded, its stringent specifications.

Description: In order to comply with the Federal Clean Water Act and, in so doing, develop a procedure to periodically update the classification, the State of Vermont evaluated the ability of LANDSAT to detect general water quality and specific water quality parameters in Vermont lakes. Unsupervised and supervised classifications as well as regression analyses were used to examine LANDSAT data from Lake Champlain and from four small nearby lakes. Unsupervised and supervised classifications were found to be of somewhat limited value. Regression analyses revealed a good correlation between depth-integrated total phosphorus concentrations and LANDSAT band 4 data (r2= 0.92) and between Secchi disk transparencies and LANDSAT band 4 data (r2 - 0.85). No correlation was found between depth-integrated chlorophyll-a samples and LANDSAT data. Vermont is expanding this LANDSAT evaluation to include the remaining lakes in the state greater than twenty acres and steps are being taken to incorporate LANDSAT into the state's ongoing water quality monitoring programs.

Description: The use of multispectral imaging systems in land use, geomorphological, and cartographic applications is examined. Spatial, spectral, and geometric resolution requirements for photo interpretation and multispectral pattern recognition are discussed. The potential contributions of these systems in specific experiments is also included.

Description: Image processing procedures for calculating the energy that roof-mounted solar collectors can potentially supply in a metropolitan area are presented. Satellite multispectral imagery from which land cover types can be determined digitally was sampled in order to estimate the percentage of land area occupied by flat or south-facing roof tops in residential and commercial/industrial areas. Procedures were applied to the various power subdistricts of the western San Fernando valley of California, and it was found that on the average 120% of the existing power demand could be met if only half the useable rooftop area were utilized, amounting to 385 MW of peak power and indicating the applicability of solar cells to power generation in urban areas.