ALBERT

Beschreibung: To take a maximum advantage of materials processing in microgravity for understanding the effects of gravity, gravity-independent effects should be minimized. In crystal growth, the quality of the grown crystals may depend, among other factors, on their interaction with the walls of the processing container during and after growth, and on the rate of the crystal cool-down at the end of the process. To investigate the above phenomena, a series of CdTe crystal growth processes was carried out. The crystals were grown by physical vapor transport without contact with the side walls of the silica glass ampoules. To eliminate the effect of the seed quality, and to reduce the number of nuclei and related crystal grains, the Low Supersaturation Nucleation technique was applied. The source temperature was 930 C, the undercooling was a few degrees. The crystals, having the diameter of 25 mm, grew at the rate of a few mm per day. The post-growth cool-down to the room temperature was conducted at different rates, and lasted from a few minutes to four days. The crystals were characterized using chemical etching, low temperature luminescence, and Synchrotron White Beam X-ray Topography techniques. The dislocation (etch pit) density was measured and its distribution was analyzed by comparison with Poisson curves and with the Normalized Radial Distribution Correlation Function. In the regions where the crystal is in contact with silica, the materials show a considerable strain field which extends for a few mm or more from the silica-crystal interface. In the reference crystal grown with contact with the ampoule walls, and when the crystals are cooled at the highest rates, the etch pit/dislocation density is in the high 10(exp 5) per square centimeter region. Typical EPD values for lower cool-down rates are in the lower 10(exp 4) per square centimeter region. In some areas the actual dislocation density was about 10(exp 3) per square centimeter or even less. No apparent effect of the cool-down rate on polygonization was observed. Low temperature PL spectra show, that the dominant peak is (D(sup 0), h) and (A(sup 0), e) for samples with low and high dislocation densities, respectively. For low EPD crystals a peak at 1.45 eV with 21 meV phonon replicas was observed and attributed to donor-acceptor pair to neutral copper-acceptor transition. In high EPD crystals this PL structure was not observed, apparently due to the masking effect of the strong contribution from the dislocation band.

Beschreibung: A series of cadmium telluride crystals grown by physical vapor transport without contact with the ampoule walls and cooled at different rates were characterized using synchrotron X-ray topography, photoluminescence, and chemical etching. Strain from sticking to silica glass and its effect on the dislocation density is shown. It was found that very fast cool-down increases dislocation density by at least one order of magnitude. None of the samples had random dislocation distributions but coarse clumping of dislocations on the scale of more than 100 microns was more prevalent in slowly cooled crystals. Photoluminescence revealed that slow cooling favored the donor-acceptor luminescence involving complex A centers. This was diminished in fast cooled material; and effect presumed to be due to dislocation gettering. Fast cooling also enhanced the formation of shallow acceptors. Implications for Bridgman growth of CdTe and the vapor growth of CdZnTe are discussed briefly.

Beschreibung: In crystal growth, the quality of the final material may depend, among other factors, on its interaction with the walls of the ampoule during and after the growth, and on the rate of the crystal cool-down at the end of ate the process. To investigate the above phenomena, a series of CdTe crystal growth processes was carried out, The crystals were grown by physical vapor transport without contact with the side walls of the silica glass ampoules, applying the Low Supersaturation Nucleation technique. The source temperature was 930 C, the undercooling was a few degrees. The crystals, having the diameter of 25 mm, grew at the rate of a few mm per day. The post-growth cool-down to the room temperature was conducted at different rates, and lasted from a few minutes to four days. The crystals were characterized using chemical etching low temperature luminescence, and Synchrotron White Beam X-ray Topography techniques. The dislocation (etch pit) density was measured and its distribution was analyzed by comparison with Poisson curves and with the Normalized Radial Distribution Correlation Function. It was found that the contact of the crystal with silica leads to a strain field and high (in the 105 sq cm range) dislocation (etch pit) density. Similar defect concentrations were found in crystals subjected to fast post-growth cool-down. Typical EPD values for lower cool-down rates and in regions not affected by wall interactions are in the lower 10(exp 4) sq cm range. In some areas the actual dislocation density was about 10(exp 3) sq cm or even less. No apparent effect of the cool-down rate on polygonization was observed. A fine structure could be discerned in low-temperature PL spectra of crystals with low dislocation density.