ALBERT

Description: The use of balloons/aerobots on Mars has been under consideration for many years. Concepts include deployment during entry into the atmosphere from a carrier spacecraft, deployment from a lander, use of super-pressurized systems for long duration flights, 'hot-air' systems, etc. Principal advantages include the ability to obtain high-resolution data of the surface because balloons provide a low-altitude platform which moves relatively slowly. Work conducted within the last few years has removed many of the technical difficulties encountered in deployment and operation of balloons/aerobots on Mars. The concept proposed here (a tethered balloon released from a lander) uses a relatively simple approach which would enable aspects of Martian balloons to be tested while providing useful and potentially unique science results. Tethered Micro-Balloons on Mars (TMBM) would be carried to Mars on board a future lander as a stand-alone experiment having a total mass of one to two kilograms. It would consist of a helium balloon of up to 50 cubic meters that is inflated after landing and initially tethered to the lander. Its primary instrumentation would be a camera that would be carried to an altitude of up to tens of meters above the surface. Imaging data would be transmitted to the lander for inclusion in the mission data stream. The tether would be released in stages allowing different resolutions and coverage. In addition during this staged release a lander camera system may observe the motion of the balloon at various heights above he lander. Under some scenarios upon completion of the primary phase of TMBM operations, the tether would be cut, allowing TMBM to drift away from the landing site, during which images would be taken along the ground.

Description: The design and operational experience with the first controlled Exo-Brake system flown during March, 2017, as conducted by the NASA Ames Research Center, is described. The Exo-Brake is an exo atmospheric braking and de-orbit device which had successfully flown twice before in a fixed-drag configuration on the nano-sat orbital platforms TechEdSat-3,4. The TechEdSat-5 flight, was the first to permit a commanded shape change which affected the drag (thus, ballistic coefficient), and thus allowed improved targeting. The use of the Iridium constellation and on-board Short Burst Data (SBD) modems, as well as Global Positioning Systems (GPS), permitted daily updates to be performed. This allowed compensation for the Thermosphere density variations captured in the F10.7 variable.Current and highly detailed analysis based on Monte-Carlo techniques suggest that approx. 7 modulations can achieve a relatively small 〈200km target ellipse at the Von Karman altitude. Drag data and over-all performance of the system is provided, as well as the description of the proposed subsequent experimental flights. There are noted advantaged for this type of de-orbit procedure as compared to a more traditional propulsion based de-orbit system.Also, the comparison with solar-sail type systems is shown to be favorable. The rapid flight series, of which this is a part, is conducted as a hands-on training environment for young professionals and university partners. In the future, such Exo-Brake systems may be used for more accurate nano-sat or small-sat disposal - or the development of technologies to permit on-demand sample return from Low Earth Orbit (LEO) scientific/manufacturing platforms.

Description: A variety of future spacecraft will be operating above the sensible earth atmosphere, but will be dipping into the atmosphere to utilize aerodynamic forces in conjunction with propulsion for its major maneuvers such as plane change. During this maneuver, the vehicle surface will experience high aerodynamic heating rates. Because these heating rates can exceed those experienced by the Shuttle, advanced thermal protection systems (TPS) must be used. This paper compares the performance of four TPS concepts operating in the same heating environment. All of them can be considered as derivatives from the development process of the TPS for the Shuttle; one has a new feature added. The results show that all of the systems require about the same weight of heatshield at high heat loads. The major difference in the weight stems from the methods of attachment to the spacecraft.

Description: Between October 16th and November 9th 2002, the first NASA Ames DDF Licancabur multidisciplinary expedition initiated the investigation of the biology and environment for life in the highest lake on Earth located at the summit of the Licancabur volcano (6017 m/20,056 ft) at the boundary of Chile and Bolivia. The low oxygen, low atmospheric pressure, high-UV radiation, average temperature, volcano-tectonic and hydrothermal environment make the site a close analog to Martian paleolakes 3.5 billion years ago. The overall goal of the project is to understand through a series of high altitude scientific expeditions what strategies life is using to defend itself against killer-level UV radiation and environmental extreme conditions at this altitude. Several other lakes are located at 4300 m at the foot of the Licancabur volcano (hereafter named laguna Blanca and Laguna Verde). They were also investigated using identical experiments and methods as for the summit lake in order to compare the results and better understand the evolution of survival strategies at transitioning elevations. The lagunas are geothermally heated and many springs provide water at various temperatures. Sources of heat are also suspected for the summit lake as its surface water temperature was measured during the successful ascent at +6 C in a -9 C ambient crater environment (with a wind chill factor of -25 C with a wind blowing almost constantly). Results of this project are expected to provide critical keys to help searching and identifying potential sites for life (extant/extinct) on Mars and developing instruments, experiments and technologies for future missions.

Description: As an aeroassisted orbital-transfer vehicle (AOTV) goes through an aerobraking maneuver, a significant amount of heat is generated. In this paper, the thermal response of a specific AOTV to this aerobrake heating is examined. The vehicle has a 70 deg, conical drag-brake heat shield attached to a cylindrical body which contains the payload. The heat shield is made of silica fabric. The heat-shield thickness is varied from that of a thin cloth to a 1.5-cm blanket. The fabric thickness, the radiation absorptivity of the vehicle surface materials, and radiation from the wake are all significant parameters in the thermal response to the heating produced by the braking maneuver. The maximum temperatures occur in the vicinity of the interface between the body and the conical heat shield.

Description: Results are presented from an on-going study of the thermal performance of thermal protection systems for a conical drag brake type AOTV. Three types of heatshield are considered: rigid ceramic insulation, flexible ceramic blankets, and ceramic cloths. The results for the rigid insulation apply to other types of AOTV as well. Charts are presented in parametric form so that they may be applied to a variety of missions and vehicle configurations. The parameters considered include: braking maneuver heat flux and total heat load, heatshield material and thickness, heatshield thermal mass and conductivity, absorptivity and emissivity of surfaces, thermal mass of support structure, and radiation transmission through thin heatshields. Results of temperature calculations presented show trends with and sensitivities to these parameters. The emphasis is on providing information that will be useful in estimating the minimum required mass of these heatshield materials.

Description: No abstract available

Description: Returning samples from Low Earth Orbit (LEO) is no simple task. Whether the samples are scientific experiments or surveillance footage, engineers must overcome many challenges to achieve mission success. In August of 1960 the first payload recovered from LEO, the Corona capsule, carried more photographic coverage of the Soviet Union than all previous U-2 missions. The Corona program proved that re-turning surveillance footage from LEO is possible, the program is still referenced today when designing new sample return missions. Although there are many crucial subsystems that make up a sample return capsule, the avionics subsystem demands the most attention. This paper will discuss how current CubeSat avionics components can be applied to large sample return missions. One advantage of using CubeSat avionics components is that they can fit into a 1.5 U (10x10x15 cm) compartment, leaving more room for the payload. This paper is broken down as follows. First, the reader is introduced to the history of sample return projects. The major design strengths of previous projects are analyzed and applied to the current capsule design. Next, the typical trajectory of a capsule is presented along with mission requirements and operations. During the re-entry phase, the avionics subsystem is responsible for commanding the deployment of the parachute, back shell, and the heat shield. Next, the power subsystem is discussed in detail including a trade study on batteries and voltage regulators. Next, the interface between the Ground Support Equipment (GSE) and the avionics components is discussed. It is important that the capsule is able to provide avionics system state of health to ensure proper functionality before the capsule is launched. Next, an in-depth analysis of current TechEdSat avionics components, with proven flight history, are presented. The various avionics components including the radios, GPS, IMU, temperature sensors, altitude sensors, and ejectors are discussed. The application of cur-rent avionics components to a sample return projects are analyzed. After, the wiring diagram is presented along with a discussion of the design. Next, a summary of how the avionics components are tested and validated is pro-vided. Finally, this article will present current sample return missions TechEdSat avionics components are being applied to. CubeSat Avionics can be applied to almost all sample return missions due to their compact configuration and proven space flight heritage. The TechEdSat team is currently making great progress in returning samples from the International Space Station (ISS) and is excited to present how their avionics components can be applied to a full-scale sample return mission.

Description: This presentation address the issues and how to involve students in the process of develping, building and certifying flight hardware for ISS and development of Mars missions.