ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

X
feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Aircraft Design, Testing and Performance  (68)
  • 1950-1954  (68)
  • 1
    facet.materialart.
    Unknown
    Fuselage Pressures Measured on the Bell X-1 Research Airplane in Transonic Flight (1953)
    In:  CASI
    Details
    Publication Date: 2019-06-28
    Description: Pressure-distribution measurements have been made on the fus elage of the Bell X- 1 research airplane. Data are presented for angles of attack from 2 deg. to 8 deg. during pull-ups at Mach numbers of about 0.78, 0.85, 0.88, and 1.02. The results of the investigation indicated that a large portion of the load carried by the fuselage was in the vicinity of the wing and may be attributed to wing-to-fuselage carryover. The presence of the wing from the 41 to 60 percent fuselage stations influenced the fuselage pressures from about 30 to 65 percent fuselage length at Mach numbers of approximat ely 0.78, 0.85, and 0.88, and from about 35 to 80 percent fuselage length at a Mach number of approximately 1.02. The fuselage contributed about 20 percent of the total airplane normal-force coefficient. The center of pressure of the fuselage load throughout the tests was located from 41 to 51 percent fuselage length, which corresponds to the forward half of the wing root-chord location.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-RM-L53I15
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 2
    facet.materialart.
    Unknown
    Effect of a Rapid Blade-Pitch Increase on the Thrust and Induced-Velocity Response of a Full-Scale Helicopter Rotor (1953)
    In:  CASI
    Details
    Publication Date: 2019-06-28
    Description: A method has been proposed for predicting the effect of a rapid blade-pitch increase on the thrust and induced-velocity response of a helicopter rotor. General equations have been derived for the ensuing motion of the helicopter. These equations yield time histories of thrust, induced velocity, and helicopter vertical velocity for given rates of blade-pitch-angle changes and given rotor-angular-velocity time histories. The results of the method have been compared with experimental results obtained with a rotor mounted on the Langley helicopter test tower. The calculated and experimental results are in good agreement, although, in general, the calculated thrust-coefficient overshoots are about 10 percent greater than those obtained experimentally.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-TN-3044
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 3
    facet.materialart.
    Unknown
    Effect of Mach Number on the Flow and Application of Compressibility Corrections in a Two-Dimensional Subsonic-Transonic Compressor Cascade Having Varied Porous-Wall Suction at the Blade Tips (1952)
    In:  CASI
    Details
    Publication Date: 2019-06-28
    Description: A cascade of 65-(12)10 compressor blades was tested at one geometric setting over a range of inlet Mach number from 0.12 to 0.89. Two groups of data are presented and compared: the first from the cascade operating conventionally with no boundary-layer control, and the second with the boundary layer controlled by a combination of upstream slot suction and porous-wall suction at the blade tips. A criterion for two-dimensionality was used to specify the degree of boundary-layer control by suction to be applied. The data are presented and an analysis is made to show the effect of Mach number on turning angle, blade wake, pressure distribution about the blade profile and static-pressure rise. The influence of boundary-layer control on these parameters as well as on the secondary losses is illustrated. A system of correlating the measured static-pressure rise through the cascade with the theoretical isentropic values is presented which gives good agreement with the data. The pressure distribution about the blade profile for an inlet Mach number of 0.21 is corrected with the Prandtl-Glauert, Karman-Tsien, and vector-mean velocity - contraction coefficient compressibility correction factors to inlet Mach numbers of 0.6 and 0.7. The resulting curves are compared with the experimental pressure distributions for inlet Mach numbers of 0.6 and 0.7 so that the validity of applying the three corrections can be evaluated.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-TN-2649
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 4
    facet.materialart.
    Unknown
    Empirical Relation Between Induced Velocity, Thrust, and Rate of Descent of a Helicopter Rotor as Determined by Wind-tunnel Tests on Four Model Rotors (1951)
    In:  CASI
    Details
    Publication Date: 2019-06-28
    Description: The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-TN-2474
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 5
    facet.materialart.
    Unknown
    An Analysis of the Autorotative Performance of a Helicopter Powered by Rotor-Tip Jet Units (1950)
    In:  CASI
    Details
    Publication Date: 2019-06-28
    Description: The autorotative performance of an assumed helicopter was studied to determine the effect of inoperative jet units located at the rotor-blade tip on the helicopter rate of descent. For a representative ramjet design, the effect of the jet drag is to increase the minimum rate of descent of the helicopter from about 1,OO feet per minute to 3,700 feet per minute when the rotor is operating at a tip speed of approximately 600 feet per second. The effect is less if the rotor operates at lower tip speeds, but the rotor kinetic energy and the stall margin available for the landing maneuver are then reduced. Power-off rates of descent of pulse-jet helicopters would be expected to be less than those of ramjet. helicopters because pulse jets of current design appear to have greater ratios of net power-on thrust to power-off, drag than currently designed rain jets. Iii order to obtain greater accuracy in studies of autorotative performance, calculations in'volving high power-off rates of descent should include the weight-supporting effect of the fuselage parasite-drag force and the fact that the rotor thrust does not equal the weight of the helicopter.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-TN-2154
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 6
    facet.materialart.
    Unknown
    The Effect of Blunt-Trailing-Edge Modifications on the High-Speed Stability and Control Characteristics of a Swept-Wing Fighter Airplane (1954)
    In:  CASI
    Details
    Publication Date: 2019-05-25
    Description: An investigation was conducted on a 35 deg swept-wing fighter airplane to determine the effects of several blunt-trailing-edge modifications to the wing and tail on the high-speed stability and control characteristics and tracking performance. The results indicated significant improvement in the pitch-up characteristics for the blunt-aileron configuration at Mach numbers around 0.90. As a result of increased effectiveness of the blunt-trailing-edge aileron, the roll-off, customarily experienced with the unmodified airplane in wings-level flight between Mach numbers of about 0.9 and 1.0 was eliminated, The results also indicated that the increased effectiveness of the blunt aileron more than offset the large associated aileron hinge moment, resulting in significant improvement in the rolling performance at Mach numbers between 0.85 and 1.0. It appeared from these results that the tracking performance with the blunt-aileron configuration in the pitch-up and buffeting flight region at high Mach numbers was considerably improved over that of the unmodified airplane; however, the tracking errors of 8 to 15 mils were definitely unsatisfactory. A drag increment of about O.OOl5 due to the blunt ailerons was noted at Mach numbers to about 0.85. The drag increment was 0 at Mach numbers above 0.90.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-RM-A54C31
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 7
    facet.materialart.
    Unknown
    A Flight Investigation of the Damping in Roll and Rolling Effectiveness Including Aeroelastic Effects of Rocket Propelled Missile Models Having Cruciform, Triangular, Interdigitated Wings and Tails (1951)
    In:  CASI
    Details
    Publication Date: 2019-06-27
    Description: The damping in roll and rolling effectiveness of two models of a missile having cruciform, triangular, interdigitated wings and tails have been determined through a Mach number range of 0.8 to 1.8 by utilizing rocket-propelled test vehicles. Results indicate that the damping in roll was relatively constant over the Mach umber range investigated. The rolling effectiveness was essentially constant at low supersonic speeds and increased with increasing mach numbers in excess of 1.4 over the Mach number range investigated. Aeroelastic effects increase the rolling-effectiveness parameters pb/2V divided by delta and decrease both the rolling-moment coefficient due to wing deflection and the damping-in-roll coefficient.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-RM-L51D16
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 8
    facet.materialart.
    Unknown
    Flight Measurements of Average Skin-Friction Coefficients on a Parabolic Body of Revolution (NACA RM-10) at Mach Numbers from 1.0 to 3.7 (1954)
    In:  CASI
    Details
    Publication Date: 2019-08-17
    Description: Measurement of average skin-friction coefficients have been made on six rocket-powered free-flight models by using the boundary-layer rake technique. The model configuration was the NACA RM-10, a 12.2-fineness-ratio parabolic body of revolution with a flat base. Measurements were made over a Mach number range from 1 to 3.7, a Reynolds number range 40 x 10(exp 6) to 170 x 10(exp 6) based on length to the measurement station, and with aerodynamic heating conditions varying from strong skin heating to strong skin cooling. The measurements show the same trends over the test ranges as Van Driest's theory for turbulent boundary layer on a flat plate. The measured values are approximately 7 percent higher than the values of the flat-plate theory. A comparison which takes into account the differences in Reynolds number is made between the present results and skin-friction measurements obtained on NACA RM-10 scale models in the Langley 4- by 4-foot supersonic pressure tunnel, the Lewis 8- by 6-foot supersonic tunnel, and the Langley 9-inch supersonic tunnel. Good agreement is shown at all but the lowest tunnel Reynolds number conditions. A simple empirical equation is developed which represents the measurements over the range of the tests.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-RM-L54G14
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 9
    facet.materialart.
    Unknown
    Tank Investigation of the Grumman JRF-5 Airplane Equipped with Twin Hydro-Skis TED No. NACA DE 357 (1951)
    In:  CASI
    Details
    Publication Date: 2019-07-11
    Description: A tank investigation has been conducted on a 1/8-size powered dynamic model of the Grumman JRF-5 airplane equipped with twin hydro-skis. The results of tests using two types of skis are presented: one had vertical sides joining the top surface to the chine; the other had the top surface faired to the chine to eliminate the vertical sides. Both configurations had satisfactory longitudinal stability although the model had a slightly greater stable elevator range available when the skis without the vertical sides were attached. Free model tests indicated no instability present when one ski emerged before the other. Considerable excess thrust was available at all speeds with either type of skis. A hump gross load-resistance ratio of 3.37 was obtained with the skis with the vertical sides and 3.53 with the other skis. Landing behavior in smooth water with yaw up to 15deg and roll up to 15deg in opposite directions was satisfactory with either type of skis.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA RM-SL52D17
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 10
    facet.materialart.
    Unknown
    Investigation of the Effects of Propeller Operation on the Low-Speed Stability and Control Characteristics of a 1/6-Scale Model of a Revised Configuration of the Republic XF-84H Airplane (1953)
    In:  CASI
    Details
    Publication Date: 2019-07-11
    Description: An investigation was made to determine the static longitudinal and lateral stability and control characteristics of a l/6-scale model of the revised Republic XF-84H airplane with and without the propeller operating. The model had a 40deg swept wing of aspect ratio 3.45 and was equipped with a thin, three-blade supersonic-type propeller. Modifications incorporated in the revised model included a raised horizontal tail, increased rudder size, wing fences at 65 percent semispan, and a modified wing leading edge outboard of the fences. The test results for flap-retracted and flap-deflected conditions indicated that the revised configuration should be satisfactory for most normal flight conditions provided the angle of attack does not exceed the angle for pitch-up. An abrupt pitch-up tendency of the model was evident for the zero thrust condition above approximately 15' angle of attack. Although the effects of power were destabilizing, power-on longitudinal stability was satisfactory through the angle-of-attack range for which the model was stable with zero thrust. Above the angle of attack for pitch-up, an uncontrollable left roll-off tendency would be expected with power on and slats retracted. Projection of wing slats or use of leading-edge chord-extensions with only the left extension drooped were found beneficial in controlling the roll-off tendency with power on; however the most effective means found was projection of only the left slat.
    Keywords: Aircraft Design, Testing and Performance
    Type: NACA-RM-SL53I24
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...