ALBERT

Description: The International Cometary Explorer (ICE) encounter with Comet Giacobini-Zinner took place 7 years after the spacecraft's original launch on 12 August 1978 as the International Sun Earth Explorer 3 (ISEE-3), part of a three-spacecraft project to study the interaction between the solar wind and the Earth's magnetosphere. Transfer to an interplanetary trajectory was performed via a 119-km-altitute, gravity-assist, lunar swingby on December 1983. Navigation support during interplanetary cruise and comet encounter was provided by orbit determination utilizing radio metric data from the DSN 64-meter antennas in Goldstone, California and Madrid, Spain. Orbit solutions yielding predictions of 50-km geocentric delivery accuracy in the target aim plane were achieved during interplanetary cruise and at comet encounter using 6-to-12-week data arcs between periodic attitude-change maneuvers. One-sigma two-way range and range rate residuals were consistently 40 meters and 0.2 mm/s or better, respectively. Non-gravitational forces affected the comet's motion during late August and early September 1985 and caused a 2300-km shift in the orbit of the comet relative to the spacecraft. This necessitated a final ICE orbit trim maneuver 3 days prior to encounter. Near-real-time assessment of two-way 2-GHz (S-band) Doppler pseudo-residuals during the June and July 1985 trajectory change maneuvers aided in calibration of the spacecraft's thrusters in preparation for this final critical maneuver. Post-flight analysis indicates tail centerline passage was achieved within 10 seconds of the predicted time and geocentric position uncertainty at encounter was less than 40 km.

Description: The Capillary Pumped Loop (CPL) experiment, G-471 is a thermal control system with high density heat acquisition and transport capability. The CPL consists of two capillary pumped evaporators with integral heaters, a fluid loop charged with ammonia (NH3), a condenser plate (heat sink), and various control electronics. The purpose of the experiment is to demonstrate the capability of a capillary pumped system under zero gravity conditions for use in the thermal control of large scientific instruments, advanced orbiting spacecraft, and space station components.

Description: The low-g fluids management group with the Center for Space Construction is engaged in active research on the following topics: gauging; venting; controlling contamination; sloshing; transfer; acquisition; and two-phase flow. Our basic understanding of each of these topics at present is inadequate to design space structures optimally. A brief report is presented on each topic showing the present status, recent accomplishings by our group and our plans for future research. Reports are presented in graphic and outline form.

Description: A list of requirements for computational fluid dynamics verification is analyzed and evaluated. Requirements include: clearly defined physics and modeling, sensitivity studies, range, validation to real conditions, duplication of key experiments and computations, and combining experiments and computations. All results are presented in viewgraph format.

Description: Information is given in viewgraph form on computational fluid dynamics (CFD) validation experiments at the Lockheed-Georgia Company. Topics covered include validation experiments on a generic fighter configuration, a transport configuration, and a generic hypersonic vehicle configuration; computational procedures; surface and pressure measurements on wings; laser velocimeter measurements of a multi-element airfoil system; the flowfield around a stiffened airfoil; laser velocimeter surveys of a circulation control wing; circulation control for high lift; and high angle of attack aerodynamic evaluations.

Description: Computational fluid dynamics objectives are presented for Marshall Space Flight Center. Topics covered include: codes in use, applications to hardware development, and the Center's benchmark plan for the future. All results are presented in viewgraph format.

Description: Requirements and meaning of validation of computational fluid dynamics codes are discussed. Topics covered include: validating a code, validating a user, and calibrating a code. All results are presented in viewgraph format.

Description: Development of a pressure-strain model, an algebraic stress model, and wall functions appropriate for flows with spanwise variations in the local wall shear stress are accomplished. Furthermore, a hot-wire measurement technique was also developed for determining the local mean velocity and Reynolds stresses in a complex flow. Experiments were performed on supersonic and subsonic turbulent flow in a square duct, flow about a strut-endwall, flow within a transition duct, and on co-flowing annular jets with swirl. All results are presented in a viewgraph format.

Description: Information is given in viewgraph form on computational fluid dynamics (CFD) for aircraft design. Topics covered include CFD validation for advanced systems, cavity flow, transonic flow, separated flow, boundary layer interaction, hypersonic flow, heat transfer, zonal modeling, the mathematical foundation for Navier-Stokes simulation, hypersonic inlets, and the role of wind tunnel tests.

Description: The objective is to establish a detailed experimental data base for evaluation of Navier-Stokes codes for confined separated flows in diffusing s-ducts. The computational thrusts include the following: (1) extension and validation of the LeRC parabolized Navier-Stokes solver, PEPSIG, into the separated flow regime using 'flare' type approximations; (2) evaluation and extensions of state-of-the-art turbulence models for confined separated flow with and without swirl; and (3) evaluation and validation of LeRC time marching 3-D Navier-Stokes code, PROTEUS, into confined separate flow regime. Various aspects of the study are presented in viewgraph form.