ALBERT

Description: Development work on an arrangement using ailerons and spoilers for lateral control was carried out by the Vought-Sikorsky Aircraft Division of the United Aircraft Corporation on a small commercial airplane in flight and on an airfoil in a wind tunnel. Spoiler hinge moments were reduced by aerodynamic balance. The arrangement was then built into an experimental airplane and further improvements were adopted as the result of flight and tunnel tests. The use of ailerons for lateral control with flaps up, spoilers with flaps full down, and gradual transition as the flaps are lowered was found to provide lateral control under the flight conditions for which they were best suited. The ailerons were of short span, permitting the use of long-span flaps, and were drooped to a relatively large angle when the flaps were deflected. A high maximum lift coefficient was thus attained. With large control deflections in the intermediate flap-angle range and spoiler effectiveness near neutral improved by "ventilating" the spoiler, the lateral control was satisfactory for the experimental airplane and was a definite improvement over that of a conventional control arrangement.

Description: An investigation has been conducted on a full-scale model of the proposed XP-46 airplane in the N. A. C. A. full-scale wind tunnel pursuant to the request of the Amy Air Corps, Materiel Division. The primary purpose of the investigation was to determine the optimum arrangement of the various component parts to obtain the maximum high speed and to provide adequate engine cooling. Additional tests included a determination of the stalling characteristics and the effectiveness of ailerons and elevators. The profile drag of the wing was ascertained by the momentum method; the location of the transition point on the wing and the critical compressibility velocities of the various airplane components were determined from surface pressure surveys.

Description: An extensive series of wind-tunnel tests on a half-scale conventional, nacelle model were made by the United Aircraft Corporation to determine and correlate the effects of many variables on cooling air flow and nacelle drag. The primary investigation was concerned with the reaction of these factors to varying conditions ahead of, across, and behind the engine. In the light of this investigation, common misconceptions and factors which are frequently overlooked in the cooling and cowling of radial engines are considered in some detail. Data are presented to support certain design recommendations and conclusions which should lead toward the improvement of present engine installations. Several charts are included to facilitate the estimation of cooling drag, available cooling pressure, and cowl exit area.

Description: Experience has shown that the determination of the take-off and. landing characteristics of airplanes requires specialized, equipment of a high degree of precision and reliability and demands great care in the evaluation and interpretation of data. It is believed, therefore, that a description of the apparatus and methods that have been developed by the NACA for these measurements might be of considerable interest, particularly to flight-test groups that have had little experience with landing and. take-off measurements. The basic principles and essential details of the Committee's equipment are described, the methods of utilizing the apparatus and of reducing the data are explained, and sample test results are presented.

Description: A flight investigation was made to determine the effect of distance flown in the icing region, antenna length, and antenna angle on the tension occurring in aircraft antennae while in regions of aircraft icing. The experimental antennas were of lengths ranging from 15 to 43 feet and were placed at angles of 0 deg to 64 deg with the airplane thrust axis. Distances up to 256 miles were flown in diverse icing conditions at true airspeeds from 157 to 214 miles per hour and pressure altitudes at which icing conditions were encountered. The results indicate that: The effect of ice formation on antenna tension increased with the angle of the antennas with the longitudinal axis of the airplane. The maximum tension for antennae having angles from 0 deg to 15 deg was 68 pounds, whereas the maximum tension for antennas having angles of 44 deg and 64 deg was 274 and 438 pounds, respectively.

Description: An equation is presented for calculating the heat flow required from the surface of an internally heated windshield in order to prevent the formation of ice accretions during flight in specified icing conditions. To ascertain the validity of the equation, comparison is made between calculated values of the heat required and measured values obtained for test windshields in actual flights in icing conditions. The test windshields were internally heated and provided data applicable to two common types of windshield configurations; namely the V-type and the type installed flush with the fuselage contours. These windshields were installed on a twin-engine cargo airplane and the icing flights were conducted over a large area of the United States during the winters of 1945-46 and 1946-47. In addition to the internally heated windshield investigation, some test data were obtained for a windshield ice-prevention system in which heated air was discharged into the windshield boundary layer. The general conclusions resulting from this investigation are as follows: 1) The amount of heat required for the prevention of ice accretions on both flush- and V-type windshields during flight in specified icing conditions can be calculated with a degree of accuracy suitable for design purposes. 2) A heat flow of 2000 to 2500 Btu per hour per square foot is required for complete and continuous protection of a V-type windshield in fight at speeds up to 300 miles per hour in a moderate cumulus icing condition. For the same degree of protection and the same speed range, a value of 1000 Btu per hour per square foot suffices in a moderate stratus icing condition. 3) A heat supply of 1000 Btu per hour per square foot is adequate for a flush windshield located well aft of the fuselage stagnation region, at speeds up to 300 miles per hour, for flight in both stratus and moderate cumulus icing conditions. 4) The external air discharge system of windshield thermal ice prevention is thermally inefficient and requires a heat supply approximately 20 times that required for an internal system having the same performance.

Description: A study was made of the performance of a jet-propulsion system composed of an engine-driven blower, a combustion chamber, and a discharge nozzle. A simplified analysis is made of this system for the purpose of showing in concise form the effect of the important design variables and operating conditions on jet thrust, thrust horsepower, and fuel consumption. Curves are presented that permit a rapid evaluation of the performance of this system for a range of operating conditions. The performance for an illustrative case of a power plant of the type under consideration id discussed in detail. It is shown that for a given airplane velocity the jet thrust horsepower depends mainly on the blower power and the amount of fuel burned in the jet; the higher the thrust horsepower is for a given blower power, the higher the fuel consumption per thrust horsepower. Within limits the amount of air pumped has only a secondary effect on the thrust horsepower and efficiency. A lower limit on air flow for a given fuel flow occurs where the combustion-chamber temperature becomes excessive on the basis of the strength of the structure. As the air-flow rate is increased, an upper limit is reached where, for a given blower power, fuel-flow rate, and combustion-chamber size, further increase in air flow causes a decrease in power and efficiency. This decrease in power is caused by excessive velocity through the combustion chamber, attended by an excessive pressure drop caused by momentum changes occurring during combustion.

Description: An investigation was conducted to compare the performance of two 25-ft-diam rotors which had identical dimensions and were similar in construction but different in blade airfoil-sections. Tests were conducted at indicated blade pitch angles from 3 degrees to 11.5 degrees and rotor speeds of 200, 290, and 371 rpm. The 23012.6 rotor required 2 percent less power to hover than the 0012.6. At thrust coefficients above design, the performance of the 23012.6 became better than the 0012.6 rotor.

Description: No abstract available

Description: Flights were made in natural icing conditions at the NACA Ice Research Project, Minneapolis, Minn. to test several designs of thermal-electric propeller de-icing blade shoes and a hub-generator design. It was found that a minimum average unit power of 2.5 watts per square inch of blade-shoe area would protect the propeller blades at the test conditions. The most satisfactory blade shoe of the three designs tested extended to the 20-percent-chord point and to 90 percent of the blade radius. A concentration of heat in the leading-edge region of this shoe was found to reduce the power input necessary for satisfactory de-icing. A satisfactory thermal design of blade shoe and a hub generator of sufficient capacity were developed.

Description: A relatively simple equation has been found to express with fair accuracy, variation in manifold-charge temperature with charge in engine operating conditions. This equation and associated curves have been checked by multi cylinder-engine data, both test stand and flight, over a wide range of operating conditions. Average mixture temperatures, predicted by the equations of this report, agree reasonably well with results within the same range of carburetor-air temperatures from laboratories and test stands other than the NACA.

Description: The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron. The results of the analysis showed that only ailerons having linear hinge-moment characteristics are unaffected by changes in rigging and indicated that ailerons having decidedly nonlinear hinge-moment-coefficient curves, particularly for deflections near 0 deg, are very sensitive to changes in rigging.

Description: Aerodynamic characteristics of a tapered NACA 23012 airfoil with single and double perforated split flaps have been determined in the NACA 7- by 10-foot wind tunnel. Dynamic pressure surveys were made behind the airfoil at the approximate location of the tail in order to determine the extent and location of the wake for several of the flap arrangements. In addition, computations have been made of an application of perforated double split flaps for use as fighter brakes. The results indicated that single or double perforated split flaps may be used to obtain satisfactory dive control without undue buffeting effects and that single or double perforated split flaps may also be used as fighter brakes. The perforated split flaps had approximately the same effects on the aerodynamic and wake characteristics of the tapered airfoil as on a comparable rectangular airfoil.

Description: An investigation has been conducted in the Langley rectangular high-speed tunnel to determine the effect of compressibility on the pressure distribution for a modified NACA 65,3-019 airfoil having a 0.20-chord flap. The investigation was made for an angle-of-attack range extending from -2 to 12 deg at .20 flap deflections from 0 to -12 deg. Test data were obtained for Mach numbers from 0.28 to approximately 0.74. The results show that the effectiveness of the trailing-edge-type control surface rapidly decreased and approached zero as the Mach number increased above the critical value.

Description: Flat-plate flaps with no wing cutouts and flaps having Clark Y sections with corresponding cutouts made in wing were tested for various flap deflections, chord-wise locations, and gaps between flaps and airfoil contour. The drag was slightly lower for wing with airfoil section flaps. Satisfactory aileron effectiveness was obtained with flap gap of 20% wing chord and flap-nose location of 80 percent wing chord behind leading edge. Airflow was smooth and buffeting negligible.

Description: The icing characteristics, the de-icing rate with hot air, and the effect of impact ice on fuel metering and mixture distribution have been determined in a laboratory investigation of that part of the engine induction system consisting of a three-barrel injection-type carburetor and a supercharger housing with spinner-type fuel injection from an 18-cylinder radial engine used on a large twin-engine cargo airplane. The induction system remained ice-free at carburetor-air temperatures above 36 F regardless of the moisture content of the air. Between carburetor-air temperatures of 32 F and 36 F with humidity ratios in excess of saturation, serious throttling ice formed in the carburetor because of expansion cooling of the air; at carburetor-air temperatures below 32 F with humidity ratios in excess of saturation, serious impact-ice formations occurred, Spinner-type fuel injection at the entrance to the supercharger and heating of the supercharger-inlet elbow and the guide vanes by the warn oil in the rear engine housing are design features that proved effective in eliminating fuel-evaporation icing and minimized the formation of throttling ice below the carburetor. Air-flow recovery time with fixed throttle was rapidly reduced as the inlet -air wet -bulb temperature was increased to 55 F; further temperature increase produced negligible improvement in recovery time. Larger ice formations and lower icing temperatures increased the time required to restore proper air flow at a given wet-bulb temperature. Impact-ice formations on the entrance screen and the top of the carburetor reduced the over-all fuel-air ratio and increased the spread between the over-all ratio and the fuel-air ratio of the individual cylinders. The normal spread of fuel-air ratio was increased from 0.020 to 0.028 when the left quarter of the entrance screen was blocked in a manner simulating the blocking resulting from ice formations released from upstream duct walls during hot-air de-icing.

Description: Cooling tests were made of a Northrop A-17A attack airplane successively equipped with a conventional.NACA cowling and with a wing-duct cooling system. The method of cooling the engine by admitting air from the propeller slipstream into wing ducts, passing it first through the accessory compartment and then over the engine from rear to front, appeared to offer possibilities for improved engine cooling, increased cooling of the accessories, and better fairing of the power-plant installation. The results showed that ground cooling for the wing duct system without cowl flap was better than for the NACA cowling with flap; ground cooling was appreciably improved by installing a cowl flap. Satisfactory temperatures were maintained in both climb and high-speed flight, but, with the use of conventional baffles, a greater quantity of cooling air appeared to be required for the wing duct system.

Description: Flight tests were made in natural icing conditions with two 8-ft-chord heated airfoils of different sections. Measurements of meteorological variables conducive to ice formation were made simultaneously with the procurement of airfoil thermal data. The extent of knowledge on the meteorology of icing, the impingement of water drops on airfoil surfaces, and the processes of heat transfer and evaporation from a wetted airfoil surface have been increased to a point where the design of heated wings on a fundamental, wet-air basis now can be undertaken with reasonable certainty.

Description: An investigation of a model of a large four-engine bomber was conducted in the Langley 19-f'oot pressure tunnel to determine the effects of several wing and nacelle modifications on drag characteristics and air flow characteristics at the tail. Leading-edge gloves, trailing-edge extensions, and modified nacelle afterbodies were tested individual ly and in combination. The effects of the various modifications were determined by force tests, tuft observations, and turbulence s1ITveys in the region of the tail. Tests were made with fixed and natural transition on the wing and with propellers operating and propellers off. Most of the tests were con- ducted at a Reynolds number of approximately 2.6 x 106. The results indicated that application of certain of the modifications provided worth-while improvements in the characteristics or the model. The flow over the wing and flaps was improved, the drag was reduced, and the turbulence in the region of the tail was reduced. Trailing-edge extensions were the most effective individual modification in improving the flow over the wing with wing flaps neutral, cowl and intercooler flaps clos ed. Modified nacelle afterbodies were the most effectiv8 individual edification in reducing drag with either fixed or natural transition on the wing; however, trailin6-edge extensions were slightly more effective with fixed transition. Combinations of either leading or trailing-edge extensions and modified afterbodies were more effective than either modification alone. With cowl and intercooler flaps open, trailing-edge extensions with modified afterbodies provided substantial improvement in flow and drag characteristics. With wing flaps deflected, enclosing the flap behind the inboard nacelle within an extended afterbody or cutting the flaps at the nacelle appeared. to be the most promising methods of improving the f low over the flaps and the tail. Although the results of hot-wire-anenometer surveys were not conclusive in regard to buffeting characteristics, the modifications did educe the turbulence at the tail with wing flaps both neutral and deflected. The modifications, as a rule, were favorable to maximum lift. Appreciable reductions in longitudinal stability of the model were caused by addition of leading -edge gloves and tr ailing -edge extensions.

Description: In open box beams subjected to torsion, secondary stresses arise owing to lateral bending of the spar caps. The present paper outlines a simple method for estimating the magnitude of these stresses and gives the results of tests of an open box beam in the neighborhood of a discontinuity where the cover changed from the top to the bottom of the box.

Description: An investigation was carried out in the NACA low-turbulence tunnel to develop low-drag airfoil sections suitable for admitting air at the leading edge. A thickness distribution having the desired type of pressure distribution was found from tests of a flexible model. Other airfoil shapes were derived from this original shape by varying the thickness, the camper, the leading-edge radius, and the size of the leading-edge opening. Data are presented giving the characteristics of the airfoil shapes in the range of lift coefficients for high-speed and cruising flight. Shapes have been developed which show no substantial increases in drag over that of the same position along the chord. Many of these shapes appear to have higher critical compressibility speeds than plain airfoils of the same thickness. Low-drag airfoil sections have been developed with openings in the leading edge as large as 41.5 percent of the maximum thickness. The range of lift coefficients for low drag in several cases is nearly as large as that of the corresponding plain airfoil sections. Preliminary measurements of maximum lift characteristics indicate that nose-opening sections of the type herein considered may not produce any marked effects on the maximum lift coefficient.

Description: In conjunction with a program of research on the general problem of stability of airplanes in the climbing condition, tests have been made of a spring-loaded tb which. is referred to as a ?springy tab,? installed on the elevator of a low-wing scout bomber. The tab was arranged to deflect upward with decrease in speed which caused an increase in the pull force required to trim at low speeds and thereby increased the stick-free static longitudinal stability of the airplane. It was found that the springy tab would increase the stick-free stability in all flight conditions, would reduce the danger of inadvertent stalling because of the definite pull force required to stall the airplane with power on, would reduce the effect of center-of-gravity position on stick-free static stability, and would have little effect on the elevator stick forces in accelerated f11ght. Another advantage of the springy tab is that it might be used to provide almost any desired variation of elevator stick force with speed by adjusting the tab hinge-moment characteristics and the variation of spring moment with tab deflection. Unlike the bungee and the bobweight, the springy tab would provide stick-free static stability without requiring a pull force to hold the stick back while taxying. A device similar to the springy tab may be used on the rudder or ailerons to eliminate undesirable trim-force variations with speed.

Description: No abstract available

Description: A correlation of what are believed to be the most reliable data available on duct components of aircraft power-plant installations is presented. The information is given in a convenient form and is offered as an aid in designing duct systems and, subject to certain qualifications, as a guide in estimating their performance. The design and performance data include those for straight ducts; simple bends of square, circular, and elliptical cross sections; compound bends; diverging and converging bends; vaned bends; diffusers; branch ducts; internal inlets; and an angular placement of heat exchangers. Examples are included to illustrate methods of applying these data in analyzing duct systems. (author)

Description: The available test results of internally balanced ailerons have been correlated and summarized herein. Although several variables have yet to-be-investigated, the results presented will be useful in the preliminary design of internally balanced ailerons and in the determination of the most promising modifications to unsatisfactory ailerons.

Description: The Army Air Force has made available several pursuit-type airplanes for quantitative investigation of their flying and handling qualities. One Item of special interest obtained from the results of the investigation is a comparison of the aileron control characteristics of the P-36, P-40, Hawker Hurricane, and Supermarine Spitfire airplanes. Figure 1 shows the design characteristics of the ailerons and the control sticks of the four airplanes. Aileron effectiveness may be expressed in terms of the helix angle generated by the wing tip in a steady roll. This angle is given by the expression pb/2V, where p is the rolling velocity, b the wing span, and V the true airspeed, expressed in consistent units. This quantity is convenient to use because, although it does not rep resent directly the rolling velocity of airplanes of different spans or airplanes operating at different speeds, it provides a satisfactory basis for computing the rate of roll and the time required to bank a given amount under any given set of conditions. The ratio of pb/2V obtained in any roll to the maximum value reached with full aileron deflection indicates the fraction of the maximum aileron travel that was reached. A complete discussion of this criterion for aileron effectiveness is given in reference 1. The aileron effectiveness of the various airplanes is compared in the following table on the basis of the response obtained with stick forces of 30 and 5 pounds. A force of 30 pounds is somewhat less than the greatest stick force exerted by the pilot. Repeated flight measurements have shown, however, that this force is a reasonable upper limit for maneuvering at high speeds.

Description: The present trend is toward faster and larger pursuit airplanes. Because both speed and size increase the aileron control forces, the design of ailerons for manual operation is becoming increasingly difficult. In order to obtain a clearer picture of the future problem of balancing ailerons, and inspection has been made of the effects of airplane size and speed on the control forces. Computations were made of the aileron control forces required to meet specified rolling conditions for plain ailerons on wings with spans from 40 to 80 feet and for speeds up to 500 miles per hour. The rolling conditions were specified by two alternative criterions. One was the rolling criterion pb/2V of reference 1. For reasons, which will be discussed later, a value of 0.09 rather than the recommended value of 0.07 was assigned to this criterion. For the criterion pb/2V, the required value of the rolling velocity p varies inversely with the airplane span b. There is some question as to whether the rolling velocity of a pursuit airplane can be permitted to decrease simply because its size is increased. For the second criterion, therefore, the rolling velocity is independent of span (p/V is a constant). The value assigned to this criterion was so chosen that for a wing of 40-foot span the value of pb/2V would be 0.09. The computations neglected compressibility effects. Available experimental data and the results of tests given in reference 2 indicate that the effect of compressibility is to increase the control force. Recent flight tests have indicated that, with certain types of aileron, serious compressibility effects may cause discontinuity at speeds of approximately 400 miles per hour in the aileron control force curves.

Description: As a part of a program of the NACA directed toward increasing the efficiency of compressors and turbines, data were obtained for application to the design of entrance vanes for axfax-flow compressors or turbines. A series of blower-blade sections with relatively high critical speeds have been developed for turning air efficiently from 0 deg to 80 deg starting with an axial direction. Tests were made of five NACA 65-series blower blades (modified NACA 65(216)-010 airfoils) and of four experimentally designed blower blades in a stationary cascade at low Mach numbers. The turning effectiveness and the pressure distributions of these blade sections at various angles of attack were evaluated over a range of solidities near 1. Entrance-vane design charts are presented that give a blade section and angle of attack for any desired turning angle. The blades thus obtained operate with peak-free pressure distributions. Approximate critical Mach numbers were calculated from the pressure distributions.

Description: An investigation has been made in the Langley free-flight tunnel to obtain an experimental verification of the theoretical rudder-free stability characteristics of an airplane model equipped with conventional rudders having negative floating tendencies and negligible friction. The model used in the tests was equipped with a conventional single vertical tail having rudder area 40 percent of the vertical tail area. The model was tested both in free flight and mounted on a strut that allowed freedom only in yaw. Tests were made with three different amounts of rudder aerodynamic balance and with various values of mass, moment of inertia, and center-of-gravity location of the rudder. Most of the stability derivatives required for the theoretical calculations were determined from forced and free-oscillation tests of the particular model tested. The theoretical analysis showed that the rudder-free motions of an airplane consist largely of two oscillatory modes - a long-period oscillation somewhat similar to the normal rudder-fixed oscillation and a short-period oscillation introduced only when the rudder is set free. It was found possible in the tests to create lateral instability of the rudder-free short-period mode by large values of rudder mass parameters even though the rudder-fixed condition was highly stable. The results of the tests and calculation indicated that for most present-day airplanes having rudders of negative floating tendency, the rudder-free stability characteristics may be examined by simply considering the dynamic lateral stability using the value of the directional-stability parameter Cn(sub p) for the rudder-free condition in the conventional controls-fixed lateral-stability equations. For very large airplanes having relatively high values of the rudder mass parameters with respect to the rudder aerodynamic parameters, however, analysis of the rudder-free stability should be made with the complete equations of motion. Good agreement between calculated and measured rudder-free stability characteristics was obtained by use of the general rudder-free stability theory, in which four degrees of lateral freedom are considered. When this assumption is made that the rolling motions alone or the lateral and rolling motions may be neglected in the calculations of rudder-free stability, it is possible to predict satisfactorily the characteristics of the long-period (Dutch roll type) rudder-free oscillation for airplanes only when the effective-dihedral angle is small. With these simplifying assumptions, however, satisfactory prediction of the short-period oscillation may be obtained for any dihedral. Further simplification of the theory based on the assumption that the rudder moment of inertia might be disregarded was found to be invalid because this assumption made it impossible to calculate the characteristics of the short-period oscillations.

Description: Two graphical methods are presented for determining the stick-free neutral point, and they are extensions of the methods commonly used to determine the stick-free neutral point. A mathematical formula for computing the stick-free neutral point is also given. These methods may be applied to determine approximately the increase in tail size necessary to shift the neutral point (stick fixed or free) to any desired location on an airplane having inadequate longitudinal stability.

Description: The material given in this report summarizes some of the results of recent research that will aid the designers of an airplane in selecting or modifying a configuration to provide satisfactory stability and control characteristics. The requirements of the NACA for satisfactory flying qualities, which specify the important stability and control characteristics of an airplane from the pilot's standpoint, are used as the main topics of the report. A discussion is given of the reasons for the requirements, of the factors involved in obtaining satisfactory flying qualities, and of the methods used in predicting the stability and control characteristics of an airplane. The material is based on lecture notes for a training course for research workers engaged in airplane stability and control investigations.

Description: No abstract available

Description: The extent of agreement of the theoretical impact computations with the actual phenomenon has not as yet been fully clarified. There is on the one hand a certain imperfection in the theory (simplifying assumptions made) and on the other an insufficiency in the experimental data available. The object of our present paper is to show how far test results agree with the available approximate computation methods, to investigate in greater detail the physical nature of impact on water, and to perfect the experimental method of studying the phenomenon.

Description: The effect of several armament installations on the drag of a 1/8 scale model of the B-32 airplane was determined. Turrets in the following positions were tested: nose, tail, upper forward, upper aft, and lower. The nose and tail turrets were each equipped with two.50-caliber guns. Upper turrets were of three types: two.50-caliber guns, four.50-caliber guns, and 20-millimeter cannon. Lower turrets were of two types: two.50-caliber guns and four.50-caliber guns. The effect of streamlining the upper two- and four-gun turrets and of extending the lower two-gun turret was determined. The tests were conducted in the Langley 19-foot. pressure tunnel at a Reynolds number of approximately 2,960,000 and a Mach number of 0.13. Large increases in drag coefficient were caused by the complete armament installations. At a lift coefficient of 0. 4 the installations with nonstreamlined upper turrets and the lower turret retracted increased the drag coefficient by 0.0022 and 0.0027 for the two-gun and four-gun turret installations, respectively. Streamlining the upper turrets reduced the drag of these installations by approximately 40 percent with the upper turrets streamlined, the drag increase was about the same for either the two- or four-gun turret installation. The streamlined two-cannon upper turrets increased the drag about the same amount as the two-gun upper turrets that were not streamlined. Extension of the lower turret. increased the drag slightly more than the whole streamlined gun-turret installation.

Description: There are forwarded herewith the results of blade motion and bouncing tests on the Kellett KD-1 three-bladed autogiro. Motion picture records and two-component accelerometer records were taken in flight during glides at air speeds from 30 miles per hour to 100 miles per hour indicator readings. Calibration curves of correct indicated air speed and rotor speed as functions of air speed meter reading were established with a trailing pitot-static head and a rotoscope, at 2,000 ft. altitude and an air density of 0.00231 slug/ cu. ft., all tests being made at approximately that density.

Description: As part of an investigation to increase the power output of the V-1710-93 engine at altitude, the engine-stage supercharger was combined with a constant-area vaneless diffuser designed to improve the performance of the engine-stage supercharger at the rated engine operating point. The performance of the modified supercharger was investigated in a variable-component supercharger test rig and compared with that of the standard supercharger with an 8-vaned diffuser. A separate evaluation of the component efficiencies and a study of the flow characteristics of the modified supercharger was made possible by internal diffuser instrumentation. At the volume flow required by the engine for rated operating conditions, the modified supercharger increased the over-all adiabatic efficiency 0.05 and the over-all pressure coefficient 0.035. Furthermore, the capacity of the engine-stage supercharger was increased by replacing the standard 8-vaned diffuser with the vaneless diffuser. The peak over-all adiabatic efficiency for the modified supercharger, however, was 0.05 to 0.07 lower than that of the standard unit over the range of tip speeds investigated. The improved performance of the modified supercharger at rated engine operating conditions resulted from a shift of the point of peak adiabatic efficiency and pressure coefficient of the standard supercharger to a higher flow. The energy loss through the vaneless diffuser was found to be small. Because of the restricted diffuser diameter, however, diffusion was inadequate, which resulted in a relatively small static-pressure rise through the diffuser, high diffuser-exit velocities, and excessive collector-case losses.

Description: The sound field of a rotating propeller is teated theoretically on the basis of aerodynamic principles. For the lower harmonics, the directional characteristics and the radiated sound energy are determined and are in conformity with existing experimental results.

Description: An investigation has been made in the Langley two-dimensional low-turbulence pressure tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65(sub 1120)-111 airfoil section modified by removing the trailing-edge cusp. The section pitching-moment characteristics and the effects of standard roughness on the section characteristics were determined for the flap retracted at Reynolds numbers ranging from 3.0 x 10(exp 6) to 9.0 x 10(exp 6).

Description: Tests were made of a 1/18-scale dynamically similar model of the Lockheed Constellation airplane to investigate its ditching characteristics and proper ditching technique. Scale-strength bottoms were used to reproduce probable damage to the fuselage. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and fuselage configuration were simulated. The behavior of the model was determined from visual observations, by recording the longitudinal decelerations, and by taking motion pictures of the ditchings. Data are presented in tabular form, sequence photographs, and time-history deceleration curves. It was concluded that the airplane should be ditched at a medium nose-high landing attitude with the landing flaps full down. The airplane will probably make a deep run with heavy spray and may even dive slightly. The fuselage will be damaged and leak substantially but in calm water probably will not flood rapidly. Maximum longitudinal decelerations in a calm-water ditching will be about 4g.

Description: Flight tests of a P-51H airplane with two different vertical-tail assemblies were made to determine lateral and directional stability and control characteristics. The airplane had satisfactory directional stability in the landing, approach, and wave-off conditions with either tail. In the power-on clean and glide conditions, however, the airplane had weak directional stability with the original tail. The production tail, which had a 7-inch fin extension and a shorter span rudder, improved the directional stability in the power-on clean and glide conditions, but the stability was still weak in the power-on clean condition. Increased altitude in either case caused a slight decrease in the stability. The rudder-trim-force change with speed with either vertical-tail assembly was high. The general aileron control characteristics were satisfactory but the aileron effectiveness failed to meet the Army handling-qualities requirements.

Description: A fundamental defect of existing methods for the determination of the polar of an airplane in flight is the impossibility of obtaining the thrust or the resistance of the propeller for any type airplane with any type engine. The new method is based on the premise that for zero propeller thrust the mean angle of attack of the blade is approximately the same for all propellers if this angle is reckoned from the aerodynamic chord of the profile section. This angle was determined from flight tests. Knowing the mean angle of the blade setting the angle of attack of the propeller blade at zero thrust can be found and the propeller speed in gliding obtained. The experimental check of the new method carried out on several airplanes gave positive results. The basic assumptions for the construction of the polars and the method of analyzing the flight data are given.

Description: An analysis of the estimated high-speed flying qualities of the Chance Vought XF7U-1 airplane in the Mach number range from 0.40 to 0.91 has been made, based on tests of an 0.08-scale model of this airplane in the Langley high-speed 7- by 10-foot wind tunnel. The analysis indicates longitudinal control-position instability at transonic speeds, but the accompanying trim changes are not large. Control-position maneuvering stability, however, is present for all speeds. Longitudinal lateral control appear adequate, but the damping of the short-period longitudinal and lateral oscillations at high altitudes is poor and may require artificial damping.

Description: Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact. Landings made at abnormally low trims led to unusually severe bounces during the runout. The least severe landing occurred after a small lending when the model was rapidly decelerated at about 0.4 g in a simulation of the proposed use of braking devices. The severity of the landings increased with wave height and was at a maximum when the wave length was of the order of from one and one-half to twice the over-all length of the model. The models with afterbodies of moderate length frequently bounced clear of the water into a stalled attitude at speeds below flying speed. The model with the long afterbody had less tendency to bounce from the waves and consequently showed less severe accelerations during the landing run than the models with moderate lengths of afterbody.

Description: Theoretical pressure distributions and measured lift, drag, and pitching moment characteristics at three values of Reynolds number are presented for a group of NACA four-digit-series airfoil sections modified for high-speed applications. The effectiveness of flaps applied to these airfoils and the effect of standard leading-edge roughness were also investigated at one value of Reynolds number. Results are also presented of tests of three conventional NACA four-digit-series airfoil sections.

Description: For computing the critical flutter velocity of a wing among the data required are the position of the line of centers of gravity of the wing sections along the span and the mass moments and radii of inertia of any section of the wing about the axis passing through the center of gravity of the section. A sufficiently detailed computation of these magnitudes even if the weights of all the wing elements are known, requires a great deal of time expenditure. Thus a rapid competent worker would require from 70 to 100 hours for the preceding computations for one wing only, while hundreds of hours would be required if all the weights were included. With the aid of the formulas derived in the present paper, the preceding work can be performed with a degree of accuracy sufficient for practical purposes in from one to two hours, the only required data being the geometric dimensions of the outer wing (tapered part), the position of its longerons, the total weight of the outer wing, and the approximate weight of the longerons, The entire material presented in this paper is applicable mainly to wings of longeron construction of the CAHI type and investigations are therefore being conducted by CAHI for the derivation of formulas for the determination of the preceding data for wings of other types.

Description: A dynamically similar model of the Army P-38 airplane was tested to determine the best way to land this airplane on the water and to determine its probable ditching performance. The tests consisted of ditching the model at various landing attitudes, flap settings, speeds, weights, and conditions of simulated damage. The model was ditched in calm water from the tank towing carriage and a few ditching were made in both calm and rough water at the outdoor catapult. The performance of the model was determined by making visual observations, by recording lengths of run and time histories of decelerations, and by taking motion pictures of the ditchings.

Description: The few available test data on the heat dissipation of wholly or partly heated airfoil models are compared with the corresponding data for the flat plate as obtained by an extension of Prandtl's momentum theory, with differentiation between laminar and turbulent boundary layer and transitional region between both, the extent and appearance of which depend upon certain critical factors. The satisfactory agreement obtained justifies far-reaching conclusions in respect to other profile forms and arrangements of heated surface areas. The temperature relationship of the material quantities in its effect on the heat dissipation is discussed as far as is possible at tk.e present state of research, and it is shown that the profile drag of heated wing surfaces can increase or decrease with the temperature increase depending upon the momentarily existent structure of the boundary layer.

Description: In the present report the true weight distribution law of the wing structure along the span is investigated. It is shown that the triangular distribution and that based on the proportionality to the chords do not correspond to the actual weight distribution, On the basis of extensive data on wings of the CAHI type airplane formulas are obtained from which it is possible to determine the true diagram of the structural weight distribution along the span from a knowledge of only the geometrical dimensions of the wing. At the end of the paper data are presented showing how the structural weight is distributed between the straight center portion and the tapered portion as a function of their areas.

Description: A spin investigation has been conducted in the Langley 20 -foot free-spinning tunnel on a 1/29 - scale model of the Republic XP-91 airplane with vee tail installed. The effects cf control settings and movements upon the effect spin and recovery characteristics of the model were determined for the clean condition (wing tanks removed, landing gear and flaps retracted). The tests were made at a loading simulating that following cruise at altitude and at a time when nearly all fuel was expended. The results indicated that the airplane might not spin at normal spinning-control configuration, but if a spin were obtained, recovery therefrom by full rudder reversal would be satisfactory. It was also indicated that aileron-against settings would lead to violent oscillatory motions and should be avoided.

Description: An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length. of 120 feet and heights ranging from 1 to 4 feet. All data and results presented in this report are given in terms of equivalent full-scale values. Summary tables and illustrative plots are used in presenting the material. The following maximum values of load and pressure are those which are apropos for effective flight paths less than 6.5deg which was the maximum value obtained in tests with the XJL-1 hull model representing full-scale landings with vertical velocity of 4.5 feet per second into 4-foot waves. The maximum local pressure on the flat portion of the bottom is 130 pounds per square inch which was measured on a 2-inch-diameter circular area near the step. The maximum local pressure obtained in the curved area near the chines is 200 pounds per square inch. This pressure was also measured near the step.

Description: The longitudinal stability and control characteristics of a B-29 airplane have been measured with a booster incorporated in the elevator control system. Tests were made to determine the effects on the handling qualities of the test airplane of variations in pilots control-force gradients as well as the effects of variations in the maximum rate of control motion supplied by the booster system.

Description: An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the normal loading were determined. Tests of the model in the long-range loading also were made. The investigation included tail-modification, spin-recovery parachute, pilot-escape, and rudder-pedal-force tests. Recoveries were generally satisfactory for spins in the normal loading provided the ailerons were not held against the spin. Satisfactory recoveries were obtained regardless of the aileron setting when the leading-edge flaps were deflected and normal recovery technique was used or when the horizontal tail was raised 70 inches, full scale. Recoveries were rapid from all inverted spins obtained. In the long-range loading with tanks on, it may be necessary to jettison the tanks in order to obtain recovery. A 12.0-foot spin-recovery parachute at the tail or a 4.0-foot parachute opened on the outer wing tip (drag coefficient of 0.66) was found to be effective for recoveries from demonstration spins. Test results showed that in an emergency the pilot should attempt to escape from the outboard side of the spinning airplane. The rudder-pedal forces in a spin were indicated to be within the capabilities of the pilot.

Description: From flight tests of 0.5-scale models of the Fairchild Lark pilotless aircraft conducted at the flight test station of the Pilotless Aircraft Research Division at Wallops Island, Va., some evaluations of the static longitudinal stability were obtained by analysis of the short-period oscillations induced by the abrupt movement of the rudder elevators. The analysis shows that for the Lark configuration with wing flap deflections of 0 degrees and 15 degrees the static longitudinal stability decreases slightly up to the critical Mach number and than as the Mach number increases further the stability increases greatly.

Description: Tables I and II of this report summarize the gust and draft velocity data for thunderstorm flights 25 and 26 of August 21, 1946 and August 22, 1946, respectively. These dta were evaluated from records of NACA instruments installed in P-61C airplanes and are of the type presented in reference 1 for previous flights. Table III summarizes the readings of a milliammeter which was used in conjunction with other equipment to indicate ambient air temperature during thunderstorm surveys. These data were read from motion-picture records of the instrument and include all cases in which variations in the instrument indications were noted during the present flights.

Description: At the request of the Air Materiel Command, Army Air Forces an investigation of the low-speed, power-off stability and control characteristics of the McDonnell XP-85 airplane is being conducted in the Langley free-flight tunnel. The XP-85 airplane is a parasite fighter carried in a bomb bay of the B-36 airplane. As a part of the investigation a few force tests were made of a 1/5 scale model of the XP-85 with a conventional tail assembly installed in place of the original design five-unit tail assembly. The total area of the conventional assembly was approximately 80 percent of the area of the five-unit assembly. The results of this investigation showed that the conventional tail assembly gave about the same longitudinal stability characteristics as the original configuration and improved the directional and lateral stability.

Description: Flight tests to determine propeller performance have been made of a Curtiss No. 838-102-18 three-blade propeller having trailing-edge extensions on a Republic P-47D-28 airplane in climb and high speed. These tests are a part of a general propeller flight-test program at the Langley Laboratory of the National Advisory Committee for Aeronautics. Results of climb tests indicate that when power is changed from approximately 1475 horsepower at 2550 rpm (roughly normal power) to 2400 horsepower at 2700 rpm (approximately military power) there is a loss in propeller efficiency of 3 percent at an altitude of 7000 feet, and 4 percent at 21,000 feet. At an airplane Mach number of 0.7 there is a gain of 9 percent in propeller efficiency when the power coefficient per blade is increased from 0.06 to 0.09. Optimum power coefficient per blade at this Mach number is estimated to be approximately 0.12. An analysis to determine the effect of the addition of extensions on the performance of the basic propeller blades indicates that climb performance was increased but high-speed performance was reduced. Both effects, however, were small.

Description: An investigation of two 1/14 scale model configurations of an outboard nacelle for the XB-36 airplane was made in the Langley two-dimensional low-turbulence tunnels over a range of airplane lift coefficients (C (sub L) = 0.409 to C(sub L) = 0.943) for three representative flow conditions. The purpose of the investigation was to develop a low-drag wing-nacelle pusher combination which incorporated an internal air-flow system. The present investigation has led to the development of a nacelle which had external drag coefficients of similar order of magnitude to those obtained previously from tests of an inboard nacelle configuration at the corresponding operating lift coefficients and from approximately one-third to one-half of those of conventional tractor designs having the same ratio of wing thickness to nacelle diameter.

Description: Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The basic lateral stability characteristics of the complete model with undeflected control surfaces are presented in the present report with a very limited analysis of the results.

Description: This report contains the flight-test results of the stalling characteristics measured during the flying-qualities investigation of the Lockheed P-8OA airplane (Army No. 44-85099). The tests were conducted in straight and turning flight with and without wing-tip tanks. These tests showed satisfactory stalling characteristics and adequate stall warning for all configurations and conditions tested.

Description: An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents the preliminary results obtained using jet nozzle 18.00 inches in diameter, with an area equal to 92.2 percent of the area of the standard jet nozzle for this engine. The experimental results presented are for conditions simulating altitudes from 20,000 to 60,000 feet and ram-pressure ratios from 1.1 to 3.5. These ram-pressure ratios correspond to flight Mach numbers between 0.374 and 1.466. Data obtained with the 18.00 inch-diameter jet nozzle and corrected to standard sea-level conditions showed substantially the same trends with altitude as the data previously obtained with an 18.75-inch-diameter nozzle and with an 18.41-inch-diameter nozzle. Jet thrust, air consumption, and fuel consumption, corrected to standard sea-level conditions, increased rapidly with increasing ram-pressure ratio. In general, corrected net thrust specific fuel consumption increased with increase in ram-pressure ratio. Corrected net thrust decreased with an increase in ram-pressure ratio at an engine speed of 8000 rpm. At corrected engine speeds between 8000 and 10,800 rpm, net thrust first decreased with an increase in ram-pressure ratio and then increased with further increase in ram pressure ratio; at corrected engine speeds above 10,800 rpm, net thrust increased continuously with increase in ram-pressure ratio. Tail-pipe temperature decreased with an increase in ram-pressure ratio.

Description: An investigation is being conducted to determine the altitude performance characteristics of the British Nene II engine and its components. The present paper presents the preliminary results obtained using a standard jet nozzle. The test results presented are for conditions simulating altitudes from sea level to 60,000 feet and ram pressure ratios from 1.0 to 2.3. These ram pressure ratios correspond to flight Mach numbers between zero and 1.16 assuming a 100 percent ram recovery.

Description: Wind tunnel tests of the 0.16-scale Douglas MX-656 model were made at low and high subsonic Mach numbers to investigate the static longitudinal- and lateral stability characteristics. The tests shows that undesirable changes in longitudinal stability at the stall were apparently caused by an altered downwash pattern at the tail. The jettisonable nose fins were highly destabilizing. Compressibility effects for the test Mach numbers were not detrimental to the longitudinal- or lateral-stability characteristics.

Description: Measurements of wing and fuselage pressure distributions were made at low and high subsonic Much numbers on a 0.16-scale model of the projected MX-656 research airplane. The MX-656 is a supersonic design utilizing a low-aspect-ratio wing and tail. Pressure-distribution measurements indicated that, although the critical Mach number of the wing was approximately 0.81 at 0 degree angle of attack, compressibility effects were of little significance below a Mach number of at least 0.90. The principal effect of compressibility was an increase in the pressure gradient over the after 30 percent of the wing chord, causing a tendency for the flow to separate. At 0.40 Mach number, the wing stalled abruptly at approximately 12 deg, angle of attack. The wing-pressure distribution showed this stall was a result of complete separation of the flow from the upper surface of the wing, Deflecting the leading-edge flaps delayed the stall to a higher angle of attack with some increase in the maximum section normal force,

Description: The results of an investigation of submerged-duct entrances are presented. It is shown that this type of entrance possesses the following characteristics: 1) very high-critical-compressibility speeds throughout the range of high-speed inlet velocity ratios; 2) very low pressure losses for the air entering the duct at all inlet-velocity ratios; and, 3) low external drag. These characteristics are obtained by the proper shaping of the contour of the upstream approach to the submerged inlets and by proper alignment of the duct lip. Design data are presented and the application of these data to a specific high-speed fighter-airplane design is discussed.

Description: Design data are presented for the graphical construction of two-dimensional sharp-edge-throat supersonic nozzles of minimum length for test-section Mach numbers from 1.20 to 10.00. The method of characteristics used in the design is briefly reviewed.

Description: An investigation of the pressure distribution on the fuselage nose and the pilot canopy of a supersonic airplane model has been conducted at a Mach number of 1.90 over a wide range of angles of attack and yaw. Boundary layer separation apparently occurred from the upper surface at angles of attack above 24 degrees and from the lower surface at minus 15 degrees. No separation from the sides of the fuselage was evident at yaw angles up to 12 degrees.

Description: The writer sets out to prove by calculation and experiment that by extensive utilization of the skin to carry axial load (reduction of stringer spacing) the stringer sections can be made small enough to afford a substantial saving in structural weight. This saving ranges from 5 to about 40 percent.

Description: An investigation was made in the Cleveland Altitude wind tunnel to determine the performance of an Aeroproducts H20C-162-X11M2 four-blade propeller on a YP-47M airplane at high blade loadings and high engine powers. The propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements are indicative only of trends in propeller efficiency with changes in power coefficient and advance-diameter ratio because unknown interference effects existed during the investigation. At a free-stream Mach number of 0.40, the envelopes of the efficiency curves decreased about 11% between advance-diameter ratios of 2.40 and 4.40. An increase in power coefficient from 0.30 to 0.80 at an advance-diameter ratio of 2.40 had little effect on the propeller efficiency. A change in power coefficient from 0.40 to 1.00 at an advance-diameter ratio of 4.40 increased the propeller efficiency by about 40%. For conditions below the stall the thrust loading on the outboard blade sections increased more rapidly than on the inboard sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall, the thrust loading decreased on the outboard sections and increased on the inboard sections.

Description: Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump. The vacuum-operated accelerating pump of the hydraulic-metering carburetor was modified to produce satisfactory accelerations by supplementing the standard air chamber with an additional 75-cubic spring. The throttle-actuated accelerating pump of the direct-metering carburetor was modified to produce satisfactory accelerations by replacing the standard 0.028-inch-diameter bleed in the load-compensator balance line with a smaller bleed of 0.0225-inch diameter. The results of this investigation indicated that both carburetors can be easily modified to produce satisfactory acceleration characteristics of the engine and no definite choice between the types of carburetor and accelerating pump can be made. Use of the direct-metering carburetor, however, probably resulted in better fuel distribution to the cylinders during the acceleration period and reduced the backfire hazard because all the fuel is introduced through the injection impeller.

Description: Three modifications of the auxiliary-stage supercharger for the V-1710-93 engine were designed and tested as part of an investigation to improve the power output and the altitude performance of the engine. A 12-vane diffuser was substituted for the standard 11-vane diffuser, and a vaneless discharge passage and a modified scroll were designed to increase the flow capacity of the supercharger and thereby to increase the performance at the high volume flows required by the engine. With the 12-vane diffuser installed and the carburetor replaced by an adapter, the equivalent volume flow at the peak efficiency point was increased 25 percent at the lowest speed investigated and 9.5 percent at the highest speed. When the carburetor was used, any increase in equivalent volume flow was masked by choking in the carburetor. A small decrease in the peak adiabatic efficiency resulted from using the 12-vane diffuser. At the high volume flows where the supercharger is required to operate, the performance was improved by the 12-vane diffuser. With the vaneless discharge passage, the surge-free range of the supercharger was increased 35 percent at the lowest tip speed investigated by increasing the maximum air flow. The maximum air flow at high tip speeds was again limited by choking in the carburetor, which masked the effect of the vaneless discharge passage on the maximum air flow. At the high volume flows near the operating point of the supercharger, the performance with the vaneless discharge passage was better than that with the standard 11-vane diffuser. At the low volume flows when the standard 11-vane diffuser gave better performance. The modified scroll gave performance characteristics that were practically the same as those of the standard scroll except at high tip speeds, where the peak performance was improved.

Description: A Douglas C-74 airplane, during a test dive at about 0.525 Mach number, experienced uncontrollable longitudinal oscillations sufficient to cause shedding of the outer wing panels and the subsequent crash of the airplane. Tests of a section of the horizontal tail plane from a C-74 airplane were conducted in the Ames 16-foot high-speed wind tunnel to investigate the possibility of the tail as a contributing factor to the accident. The results of the investigations of fabric-covered elevators in various conditions of surface deformation are presented in this report.

Description: Attempts were made to alleviate the buffeting of external fuel tanks mounted under the wings of a twin-engine Navy fighter plane. The Mach number at which the buffeting began was increased from 0.529 to 0.640 by streamlining the sway braces and increasing the lateral rigidity of the sway brace system. Further increases of the Mach number, at which buffeting began to 0.725, was obtained by moving the external fuel tank to a position under the fuselage.

Description: This report contains the flight-test results of the lateral and directional-stability and control phase (including tests with wing-tip tanks) of a general flying-qualities investigation of the Lockheed P-80A airplane (Army No. 44-85099). These tests were conducted at indicated airspeeds up to 494 miles per hour (0.691 Mach number) at low altitude and up to 378 miles per hour (0.816 Mach number) at high altitude. These tests showed that the flying qualities of the airplane were for the most part in accordance with the requirements of the Army Air Forces Stability and Control Specifications. The only major deficiency noted was the negative lateral stability with the wing-tip tanks installed.

Description: An experimental investigation concerned primarily with the extension of test data on the drag of revolving disks, cylinders, and streamline rods to high Mach numbers and Reynolds numbers is presented.

Description: An investigation was conducted to correlate the knock limited performance of flight and single-cylinder engines under a variety of operating conditions.

Description: The NACA 23012-4 airfoil was investigated for the purpose of increasing lift by means of blowing out air from the wing, in conjunction with the effect of plain flap of variable contour and slotted flap of 25 percent chord length. The wing also was provided with a hinged nose, to be deflected at will. Air was blown out frcm the wing immediately in front of the flap; also at the opening between wing and hinged nose,tangentially to the surface of the wing. Another device employed to increase maximum lift was a movable slat, to be opened to form a clot. Lift was measured in relation to the volume of blown-out air and considerable increases were observed with increasing volume.

Description: Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.

Description: Unduly high diving speeds can be effectively controlled by diving brakes but their employment involves at the same time a number of disagreeable features: namely, rotation of zero lift direction, variation of diviving moment, and, the creation of a potent dead air region.

Description: An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-stream Mach number of 0.40. Results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio because no corrections for the effects of tunnel-wall constriction on the installation were applied. Slipstream surveys are presented to illustrate blade thrust load distribution for certain operating conditions. Within the range of advance-diameter ratios investigated at each free-stream Mach number, the efficiency of the four-blade propeller decreased as the power coefficient was increased from 0.10 to 1.00. For the three-blade propeller, nearly constant maximum efficiencies were obtained for power coefficients from 0.32 to 0.63 at advance-diameter ratios between 1.90 and 3.00. In general, for conditions below the stall and critical tip Mach number, the maximum thrust load shifted from the inboard sections toward the tip sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall or critical tip Mach number, losses in thrust occurred on the outboard blade sections owing to flow break-down; the thrust load increased slightly on the inboard sections.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel to evaluate the spin, longitudinal-trim, and tumbling characteristics of a 1/20-scale model of the Consolidated Vultee MX-813 airplane. The effects of control position were determined for the model ballasted to represent the airplane in its design gross weight loading. The model, in general, would not spin but demonstrated a tendency to trim at very high stalled angles of attack. Static tests substantiated the dynamic tests as regards the trim characteristics. Movement of the elevator, however, from up to slightly down was effective in pitching the model from stalled to normal trim attitudes. The model would not tumble.

Description: The present report, which deals with pressure-distribution measurements made on a sweptback wing with a jet engine nacelle, is similar to a report on pressure-distribution measurements on a rectangular wing with a jet engine nacelle (second partial report). Here, in investigations preliminary to high-speed measurements, as in the second partial report, useful arrangements and fillet designs have been discovered.

Description: The present report, which forms the first of six articles on experiments with airfoils of aspect ratio from 1 to 3 and various planforms, deals with the three- and six-component measurements made on the trapezoidal wing series in the 2.15 x 3-meter wind tunnel of the DVL at the request of the Henschel Aircraft Company.

Description: A summary has been made of available data on the characteristics of airfoil sections with trailing-edge high-lift devices. Data for plain, split, and slotted flaps are collected and analyzed. The effects of each of the variables involved in the design of the various types of flap are examined and, in cases where sufficient data are given, optimum configurations are deduced. Wherever possible, the effects of airfoil section, Reynolds number, and leading-edge roughness are shown. For single and double slotted flaps, where a great mass of unrelated date are available, maximum lift coefficients of a large number of configurations are presented in tables.

Description: An investigation was conducted on an 0.08-scale semispan model of the Chance Vought XF7U-1 airplane in the Langley high-speed 7- by 10-foot tunnel in the Mach number range from 0.40 to 0.97. The results are compared with those obtained with an 0.08-scale sting-mounted complete model tested in the same tunnel and with an 0.026-scale semispan model tested by the wing-flow method. The lift-curve slopes obtained for the 0.08-scale semispan model and the 0.026-scale wing-flow model were in good agreement but both were generally lower than the values obtained for the sting model. The results of an unpublished investigation have shown that tunnel-wall boundary-layer and strut-leakage effects can came the difference noted between the lift-curve slopes of the sting and the semispan data. Fair agreement was obtained among the data of the three models as regard the variation of pitching-moment coefficients with lift coefficient. The agreement between the complete and the semispan models was more favorable with the vertical fine on, because the wall-boundary-layer and strut leakage effects were less severe. In the Mach number range between 0.94 and 0.97, ailavator-control reversal was indicated in the wing-flow data near zero lift; Whereas, these same trends were indicated in the larger scale semispan data at somewhat higher lift coefficients.

Description: Tests have been made in Langley tank no. I of a dynamic model of the Consolidated Vultee PB2Y-3 airplane. These tests were made using an alternate hull form, the purpose of which was to reduce the bow spray and eliminate the landing instability which are objectionable features of the production design. The major differences from the PB2Y-3 hull included a deeper step to improve the landing stability , and a lengthened forebody and increased beam to reduce the sway in the propellers and on the flaps. The tests showed that the spray characteristics of the revised hull form were much better than that ot the production design. In addition the take-off and landing stability of the model with the alternate hull were satisfactory.

Description: The basic principles of the control of TL ongincs are developed on .the basis of a quantitative investigation of the behavior of these behavior under various operating conditions with particular consideration of the simplifications pormissible in each case. Various possible means of control of jet engines are suggested and are illustrated by schematic designs.

Description: The drag coefficients of bombs at high velocities velocity of fall was 97 percent of the speed of sound) (the highest are determined by drop tests and compared with measurements taken in the DVL high-speed closed wind tunnel and the open jet at AVA - Gottingen.

Description: Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium. It appears, therefore, that the oscillatory motions reported for the airplane may have been the direct result of control movements rather than the result of inherent oscillatory tendencies.

Description: The present report is concerned with a series of tests on a model airplane fitted with four types of dive flaps of various shapes, positions, and incidence located near the leading edge of the wing (from 5 to 20 percent of the wing chord). Tests were also made on a stub airfoil fitted with a ventral dive (located at 8 percent of the wing chord). The hinge moments of the dive flaps were measured.

Description: The spin and recovery characteristics of the Curtiss-Wright XP-87 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape, are presented in this report. The characteristics were estimated rather than determined by model tests because the XP-87 dimensional and mass characteristics were considered to be noncritical and because data were available from model tests of several similar airplanes. The study indicated that the recovery characteristics of the airplane will be satisfactory for all loadings if the controls are reversed fully and rapidly. The control forces, however, will probably be beyond the capabilities of the pilot unless some additional balance or a booster is used. A 6-foot tail parachute or a 3.5-foot wing-tip parachute with a drag coefficient of 0.7 will be a satisfactory, emergency spin-recovery device for spin demonstrations. If it is necessary for the crew to abandon the spinning airplane, they should leave from the outboard side of the cockpit.

Description: The results obtained from measurements of gust and draft velocities within thunderstorms for the period July 22, 1946 to July 23, 1946 at Orlando, Florida, are presented herein. These data are summarized in tables I and II, respectively, and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records for the flights indicated that no data on ambient air temperature variations within thunderstorms were obtained.

Description: Tests with a dynamically similar model of the Navy XP4M-1 airplane were made to determine the best way to land the airplane in calm and rough water, to determine its probable ditching performance, and to determine practicable modifications which could be incorporated in the design of the airplane that would improve its ditching characteristics. The results were obtained by making visual observations, by recording longitudinal decelerations,a nd by taking motion pictures of the landings. A list of conclusions from the test results is included.

Description: An investigation has been made in the Langley two-dimensional low-turbulence tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65 (112)-111 airfoil section modified by removing the trailing-edge cusp. The results of the investigation indicate that for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6), the flap deflection was 45 degrees and the flap leading-edge radius center was 0.73 percent-chord behind and 4.46 percent-chord below the slot lip. The maximum section lift coefficient for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6) was 2.46 or 0.12 higher than that obtained for an NACA 65-210 airfoil section with a 0.250-chord slotted flap.

Description: This report presents the result of tests of a 0.35-scale model of the Bell P-39N-l airplane. Included are the longitudinal-stability and - control characteristics of the airplane as indicated by tests of the model equipped with each of two different sets of elevators. The results indicate good longitudinal stability and control throughout the speed range encounterable in flight. The variation of estimated stick force with speed was less when the model was equipped with elevators constructed to the theoretical design dimensions than when equipped with elevators as built to scale from measurements of the corresponding-parts of the actual airplane. The predicted stick forces required to produce the normal accelerations attainable in flight are within the limits specified by the Army Air Forces.

Description: Spin tests have been performed in the Langley 20-foot free-spinning tunnel on a 1/35-scale model of the Douglas XB-43 airplane. The spin and recovery characteristics were determined for several loading conditions of the airplane. The effects of installing a dorsal fin and of installing a ventral fin were investigated. Emergency escape of the crew was simulated and the stick and rudder pedal forces necessary to effect recoveries on the airplane were determined.

Description: A preliminary evaluation of the spin and recovery characteristics of the XF3D-1 airplane has been made, based primarily on the results of the free-spinning tunnel tests of a model which closely simulated the XF3D-1 in tail design, tail length, and mass loading. Estimates have been made of the rudder-pedal force that may be encountered in effecting recovery from a spin and of the spin recovery parachute requirements of the airplane for demonstration spins. The method of bail-out which should be used if it becomes necessary for the crew to abandon the airplane during a spin is indicated. It was indicated that the recovery characteristics of the XF3D-1 airplane in the clean condition for erect and inverted spins would be satisfactory for all loadings specified by the contractor as possible on the airplane. However, if a spin is inadvertently entered while the landing flaps are down, recovery may be slow. The slow-down brakes and the landing flaps should be retracted immediately upon the inception of a spinning condition, after which recovery from the spin should be attempted. The pedal force necessary to reverse the rudder during a spin will be within the physical capabilities of the pilot. Opening a 10-foot diameter parachute attached to the tail (laid-out-flat diameter, drag coefficient 0.7) or a 4.5-foot diameter parachute attached to the outboard wing tip will insure satisfactory spin recovery from demonstration spins. If it becomes necessary for the crew to abandon the airplane during a spin, they should leave from the outboard side of the cockpit.

Description: Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size). Maximum normal accelerations of about 6.5g were obtained in 4.4 inch waves and 8.5g were obtained in 8.0 inch waves. A maximum angular acceleration corresponding to 16 radians per second per second, full size, was obtained in the higher waves. The data indicate that the airplane will experience its greatest accelerations when landing in waves of about 20 feet (140 ft, full size) in length.

Description: In the following, high-speed measurements on a swept-back wing are reported. The curves of lift, moment, and drag have been determined up to Mach numbers of M = 0.87, and they are compared to a rectangular wing. Through measurements of the total-head loss behind the wing and through schlieren pictures, an insight into the formation of the compression shock at high Mach numbers has been obtained.

Description: Tests were conducted in calm water in Langley tank no. 2 and in calm and rough water at an outdoor catapult in order to determine the best way to make a forced landing of an Army A-26 airplane and to determine its probable ditching behavior. These tests were requested by the Air Materiel Command, Army Air Forces, in their letter of March 26, 1943, WEL:AW:50.

Description: A series of investigations of several 1/14-scale models of an inboard nacelle for the XB-36 airplane was made in the Langley two-dimensional low-turbulence tunnels. The purpose of these investigations was to develop a low-drag wing-nacelle pusher combination which incorporated an internal air-flow system. As a result of these investigations, a nacelle was developed which had external drag coefficients considerably lower than the original basic form with the external nacelle drag approximately one-half to two-thirds of those of conventional tractor designs. The largest reductions in drag resulted from sealing the gaps between the wing flaps and nacelle, reducing the thickness of the nacelle training-edge lip, and bringing the under-wing air inlet to the wing leading edge. It was found that without the engine cooling fan adequate cooling air would be available for all conditions of flight except for cruise and climb at 40,000 feet. Sufficient oil cooling at an altitude of 40,000 feet may be obtained by the use of flap-type exit doors.