ALBERT

Description: The Single-Mode Projection Filter (SPF) is a newly developed algorithm for eigensystem parameter identification from both analytical results and test data. The SPF is formulated with a single mode only and practical for parallel processing implementation. Explicit formulations of SPF are derived for the multi-input multi-output (MIMO) system by using the orthogonal matrices of the controllability and observability matrices in the general sense. The modal parameters of SPF are initially obtained from an analytical model in modal space. The experimental data are then processed through SPF to update its modal parameters and to minimize a cost function defined by the norm of an error matrix. The updated modal parameters represent the characteristics of the test data. A two-dimensional global minimum optimization algorithm is developed and applied for the filter update by using the interval analysis method. The SPF is developed based on a single-mode subsystem and identifies only one modal frequency and one modal damping within a specified region. For an n-modes structure, n SPF can be implemented for parallel processing to reduce the computational burden. The SPF is applied to analyze the simulated data for the MAST beam structure. The estimated modal parameters are comparable to those from the Eigensystem Realization Algorithm (ERA) and repeated modal frequencies are identified. The modal analysis of the Spacecraft Control Laboratory Experiment (SCOLE) data is also performed by using the ERA and the Maximum Likelihood Estimate (MLE). The result shows that the first five modal frequencies are very close from ERA and MLE. However, there are slight disparities in the damping rates and the computational burdens are quite different among these two algorithms.

Description: Satellite scatterometers are active microwave radars designed to yield measurements of near surface horizontal wind velocity over the ocean. Scatterometers are unique in that they are the only existing microwave remote sensing instruments that allow measurements of both wind speed and wind direction. NASA will fly a scatterometer, NSCAT, aboard the Navy Ocean Remote Sensing System (N-ROSS) mission starting in late 1990. N-ROSS is a spaceborne ocean remote sensing system with a planned mission life of three years. In addition to the NSCAT, N-ROSS will have three other microwave instruments mounted on a single satellite flying in a near polar orbit: an altimeter; a special sensor microwave/imager (SSM/I); and a low frequency microwave radiometer. The NSCAT to be flown on N-ROSS is described.

Description: The following topics are addressed: (1) motivation for the National Meteorological Center (NMC) simulation project; (2) history of the NMC simulation project; (3) experimental design of the WINDSAT observing system simulation experiment; (4) preparation of the simulated observations; and (5) strengths and weaknesses of the experimental design.

Description: High-resolution cloud motion wind (CMW) data sets obtained from geostationary satellites for approximately the past decade have been used for the purpose of estimating mesoscale wind fields in various research studies. Yet there remains much controversy surrounding the proper interpretation and use of the resultant wind vector and kinematic fields. This paper is concerned with: (1) how representative are cloud draft winds of actual ambient air motions; and (2) what is the degree of practical usefulness of CMW fields for both mesoscale analysis and as input to numerical weather prediction models.

Description: A potential improvement on measuring atmospheric winds by using a coherent Doppler system has led to a need for detailed knowledge concerning the aerosol backscattering characteristics, especially at CO2 wavelengths. In order to meet this requirement, a plan of study has been developed to establish a global data base of atmospheric aerosol backscattering coefficients.

Description: Photographs of cloud scenes taken from the orbiting space shuttle are being used to assess the overestimation in the amount of cloud cover sensed by satellites at angles other than nadir. Also these photographs and Landsat images indicate that the frequency distributions of clear and of cloudy intervals, at least in simple tropical cloud scenes, may be approximated by common distribution functions.

Description: It has been proposed that a Doppler lidar be placed in a polar orbit and scanned to provide estimates of lower tropospheric winds twice per day and with a spatial resolution of 300 km. Initial feasibility studies conducted primarily by NOAA and NASA presented an optimistic outlook for a space based lidar. The technology appeared within reach and initial computer simulations suggested that acceptable accuracies could be obtained. Those early studies exposed, however, several potential problem areas which included: (1) the algorithms for computing the wind vectors did not perform well when there were coherent gradients in the wind fields; and (2) the lifetime and power requirements of the lidar put severe restrictions on the pulse repetition frequency (PRF). These two basic problems are currently being addressed by a Doppler lidar simulation study focussed upon three primary objectives: (1) to develop optimum scan parameters and shot patterns for a satellite-based Doppler lidar; (2) to develop robust algorithms for computing wind vectors from lidar returns; and (3) to evaluate the impact of coherent mesoscale structures (wind gradients, clouds, aerosols) on up-scale wind estimates. An overview is provided of the simulation efforts with particular emphasis upon rationale and methodology. Since this research is currently underway, any results shown are meant only as evidence of progress.

Description: The Wave Propagation Laboratory of the National Oceanic and Atmospheric Administration's (NOAA) Environmental Research Laboratories has investigated the feasibility of measuring the global wind field by using an infrared coherent laser radar under a joint program with the U.S. Air Force Space Division Defense Meteorological Satellite Program (DMSP). These studies considered both the analytical and hardware feasibility of a spaceborne global wind measuring coherent laser radar (WINDSAT). Objectives and requirements of the Air Force Defense Meteorological Satellite Program were used in the study. The vertical distributions of the horizontal wind field were required throughout the troposphere with 300 km square horizontal and 1 km vertical resolution with a measurements accuracy of 1 m/s. Complete global coverage was required. The lidar system performance should also be scalable to operational satellite conditions. The analytical studies were performed for both a 300 km altitude Space Shuttle orbit and an operational polar orbit of 800 km altitude (Huffaker, 1978; Huffaker et al., 1980). A hardware definition study was performed for a Space Shuttle demonstration test flight (Lockheed Missiles and Space Co., 1981). Studies have also been conducted to determine the feasibility of mounting a WINDSAT payload on an Advanced TIROS-N spacecraft (RCA Corporation, 1983).

Description: A study has been completed to define a Shuttle experiment that solves the most crucial scientific and engineering problems involved in building a satellite Doppler wind profiler for making global wind measurements. The study includes: (1) a laser study to determine the feasibility of using the existing NOAA Windvan laser in the Space Shuttle spacecraft; (2) a preliminary optics and telescope design; (3) an accommodations study including power, weight, thermal, and control system requirements; and (4) a flight trajectory and operations plan designed to accomplish the required scientific and engineering goals. The experiment will provide much-needed data on the global distribution of atmospheric aerosols and demonstrate the technique of making wind measurements from space, including scanning the laser beam and interpreting the data. Engineering accomplishments will include space qualification of the laser, development of signal processing and lag angle compensation hardware and software, and telescope and optics design. All of the results of this limited Spacelab experiment will be directly applicable to a complete satellite wind profiler for the Earth Observation System/Space Station or other free-flying satellite.

Description: WINDSAT is a proposed space based global wind measuring system. A Shuttleborne experiment is proposed as a proof of principle demonstration before development of a full operational system. WINDSAT goals are to measure wind speed and direction to + or - 1 m/s and 10 deg accuracy over the entire earth from 0 to 20 km altitude with 1 km altitude resolution. The wind measuring instrument is a coherent lidar incorporating a pulsed CO2 TEA laser transmitter and a continuously scanning 1.25 m diameter optical system. The wind speed is measured by heterodyne detecting the backscattered return laser radiation and measuring this frequency shift.

Description: Hitherto, long-range wind-sensing coherent (heterodyne) lidars have utilized CO2 lasers (operating at a 10-micrometer wavelength) since these were the only high-power single-mode (spatial and axial) pulsed sources available. This property ensures temporal coherence over the required spatial resolution, e.g., the pulse length. Recent developments in Nd:YAG lasers makes possible the consideration of a 1.06-micrometer source (Kane et al., 1984). The relative merit of operation at various wavelengths is a function of system parameter, backscattering cross section, signal processing, beam propagation, and practical and eye safety considerations. These factors are discussed in the context of a global wind-sensing coherent lidar.

Description: The rapid development of laser diodes offers the opportunity to design an all solid state transmitter for coherent Doppler lidar by using Nd:YAG as the gain medium. We have demonstrated that the components of such a system operate as expected. We believe that LD-pumped solid state laser oscillators and amplifiers offer an approach to space qualified transmitters with coherence, power, efficiency, and operating lifetime necessary to meet satellite platform requirements.

Description: Coherent laser radar systems at 10 micrometers have been studied in Europe for well over a decade. In the past few years, the level of activity has increased rapidly and work is now in progress on systems and components at a large number of research institutions and industrial firms. Some of the organizations have had specific involvement with wind and aerosol measuring lidars, while others are largely concerned with components. Some of the particular European strong points are reviewed in device physics and technology. In addition to wind measurement systems, much work has been done on other applications of coherent laser radar including ranging, imaging, and coherent DIAL studies. Some of these other applications are also outlined.

Description: Now, there are four Doppler lidar configurations which are being promoted for the measurement of tropospheric winds: (1) the coherent CO2 Lidar, operating in the 9 micrometer region using a pulsed, atmospheric pressure CO2 gas discharge laser transmitter, and heterodyne detection; (2) the coherent Neodymium doped YAG or Glass Lidar, operating at 1.06 micrometers, using flashlamp or diode laser optical pumping of the solid state laser medium, and heterodyne detection; (3) the Neodymium doped YAG/Glass Lidar, operating at the doubled frequency (at 530 nm wavelength), again using flashlamp or diode laser pumping of the laser transmitter, and using a high resolution tandem Fabry-Perot filter and direct detection; and (4) the Raman shifted Xenon Chloride Lidar, operating at 350 nm wavelength, using a pulsed, atmospheric pressure XeCl gas discharge laser transmitter at 308 nm, Raman shifted in a high pressure hydrogen cell to 350 nm in order to avoid strong stratospheric ozone absorption, also using a high resolution tandem Fabry-Perot filter and direct detection. Comparisons of these four systems can include many factors and tradeoffs. The major portion of this comparison is devoted to efficiency. Efficiency comparisons are made by estimating the number of transmitted photons required for a single pulse wind velocity estimate of + or - 1 m/s accuracy in the middle troposphere, from an altitude of 800 km, which is assured to be reasonable for a polar orbiting platform.

Description: To gain a proper perspective of the potential of coherent Doppler lidars for global wind sensing sometime in the future, we need to examine where we are, how we got here, and the expectations for future lidar system development. First we give a brief review of lidar developments leading to our present technology. Next we survey present U.S. infrared systems with particular attention to the pulsed systems since they are the ones that will have sufficient range to operate from satellites. Finally we comment on trends and probable future developments. Only unclassified lidars are considered. The considerable DoD support for classified applications certainly enhances future developments in components and subsystems.

Description: This paper describes the current status of a prototype 0.53 micrometer Doppler lidar system under development at RCA. This system consists of a frequency doubled Nd:YAG laser constrained to yield a narrow bandwidth, single frequency pulse, a Fabry-Perot Inteferometer (FPI) using an Image Plane Detector (IPD) to measure the backscatter spectrum for each pulse and a Data Acquisition System (DAS) to sample, store, and analyze the backscattered signal. These individual subsystem components have been assembled and preliminary atmospheric testing has recently begun. Atmospheric backscatter spectra are presented which demonstrate the capabilities of this system to distinguish between return signals from aerosols, molecules, and clouds.

Description: The topics covered include the following: principles of Doppler measurements, laser backscatter, eye safety, demonstration concepts, the wavelength-meter, the interferometer detector, return signal model, and comparison of incoherent and coherent lidars.

Description: Nature has provided us with a natural and easily visible method of tracing atmospheric motion through the measurement of cloud velocities. This source of wind information has been available from geosynchronous satellites since the launch of the ATS-1 Spin Scan camera. This sensor provided adequate spatial and temporal resolution views of individual cloud systems that could represent the wind with useful accuracy. During the last decade, cloud motion derived winds have become part of the operational system as they are routinely provided to the National Meteorological Center as input to the global numerical models. The principal limitations of cloud motion winds are that they (1) can be measured within the limits that cloud motions can represent the wind only where trackable clouds exist, (2) require knowledge of the cloud height, (3) require high spatial and temporal resolution geosynchronous satellite systems with high attitude determination accuracy, and (4) need sophisticated interactive computer systems for the calculation of high resolution fields. These limitations are examined and suggestions are made for how this product could be improved. Also, uses of the data for mesoscale purposes are discussed.

Description: The story of the Aircraft to Satellite Data Relay (ASDAR) program began when airline meteorologists realized that B-747's and other commercial jets provided cockpit displays of digital values for outside air temperature and winds. Later, when a few B-747's were used to carry portable air quality monitoring equipment for the Global Air Sampling Program (GASP), scientists at NASA-Lewis explored ways in which these digital values could be used to label data collected during the GASP flights. Digital values of GASP analyses were recorded along with digital values of location and altitude, time, winds, and temperature, obtained by microprocessors from within the host aircraft's avionics. These data suggested a way in which manually recorded in-flight meteorological reports could be replaced by an automatic system, which could record winds and air temperatures as often as desired. NASA's prototype ASDAR showed that automated data relay by meteorological geostationary satellites could be accomplished from an aircraft. Testing of the instruments and analyses of its data are examined.

Description: A balloon-borne triple-etalon Fabry-Perot Interferometer, observing the Doppler shifts of absorption lines caused by molecular oxygen and water vapor in the far red/near infrared spectrum of backscattered sunlight, has been used to evaluate a passive spaceborne remote sensing technique for measuring winds in the troposphere and stratosphere. There have been two successful high altitude balloon flights of the prototype UCL instrument from the National Scientific Balloon Facility at Palestine, TE (May 80, Oct. 83). The results from these flights have demonstrated that an interferometer with adequate resolution, stability and sensitivity can be built. The wind data are of comparable quality to those obtained from operational techniques (balloon and rocket sonde, cloud-top drift analysis, and from the gradient wind analysis of satellite radiance measurements). However, the interferometric data can provide a regular global grid, over a height range from 5 to 50 km in regions of clear air. Between the middle troposphere (5 km) and the upper stratosphere (40 to 50 km), an optimized instrument can make wind measurements over the daylit hemisphere with an accuracy of about 3 to 5 m/sec (2 sigma). It is possible to obtain full height profiles between altitudes of 5 and 50 km, with 4 km height resolution, and a spatial resolution of about 200 km, along the orbit track. Below an altitude of about 10 km, Fraunhofer lines of solar origin are possible targets of the Doppler wind analysis. Above an altitude of 50 km, the weakness of the backscattered solar spectrum (decreasing air density) is coupled with the low absorption crosssection of all atmospheric species in the spectral region up to 800 nm (where imaging photon detectors can be used), causing the along-the-track resolution (or error) to increase beyond values useful for operational purposes. Within the region of optimum performance (5 to 50 km), however, the technique is a valuable potential complement to existing wind measuring systems and can provide a low cost addition to powerful active (LIDAR) wind measuring systems now under development.

Description: A survey is presented of instrumentation suitable for measurement of wind near the surface of the earth by using in-situ techniques and further restricted to sensors that are operational. In this case, a sensor is deemed to be operational if it is commercially available. There is no discussion here of the systems that might be used to acquire, process, display, and store the sensor data. It is assumed that some sort of automatic data logging equipment would be used. Without special requirements such as need for high frequency response, low power consumption, etc., this treatment must be quite general and provides little detail. Also, without special restrictions, emphasis must be placed on conventional sensors that provide the bulk of wind data today.

Description: The superpressure balloon was developed to provide a method of obtaining global winds at all altitudes from 5 to 30 km. If a balloon could be made to fly for several weeks at a constant altitude, and if it could be tracked accurately on its global circuits, the balloon would provide a tag for the air parcel in which it was embedded. The Lagrangian data on the atmospheric circulation would provide a superior data input to the numerical model. The Global Atmospheric Research Program (GARP) was initiated in large part based on the promise of this technique coupled with free-floating ocean buoys and satellite radiometers. The initial name proposed by Charney for GARP was SABABURA 'SAtellite BAlloon BUoy RAdiometric system' (Charney, 1966). However, although the superpressure balloon exceeded its designers' expectations for flight duration in the stratosphere (longest flight duration of 744 days), flight duration below 10 km was limited by icing in super-cooled clouds to a few days. The balloon was relegated to a secondary role during the GARP Special Observing Periods. The several major superpressure balloon programs for global wind measurement are described as well as those new developments which make the balloon once again an attractive vehicle for measurement of global winds as a reference and bench-mark system for future satellite systems.

Description: The accuracy is studied of temperature estimates derived from the divergence equation when wind observations of various spatial and temporal resolutions and accuracies are available. The basic data set used is the high resolution model data set used by Kuo and Anthes (1984a) in observing systems simulation experiments (OSSE) designed to estimate the errors in heat and moisture budgets (Kuo and Anthes, 1984b) calculated from the AVE-SESAME-1979 spatial observational network. This model data set is modified in ways to simulate wind observations that appear feasible from an operational regional network of wind profilers.

Description: Continuous, automated measurement of tropospheric wind profiles with UHF and VHF Doppler radars has been demonstrated. Ground-based networks of these radars will be available as part of a global wind measurement system, and remote single stations could be built to further complement a spaceborne measurement device. A number of ground-based wind profilers will be in place by the time a space system is tested so the global wind measurement system should be designed with these ground-based profilers providing part of the picture.

Description: The Upper Atmosphere Research Satellite (UARS), to be launched in 1989, is to provide a global data set required to understand the mechanisms controlling upper atmosphere structure and processes, as well as the response of the upper atmosphere to natural and human perturbations. The High Resolution Doppler Imager (HRDI) is the primary instrument for measuring the dynamics of the stratosphere and mesosphere. The goal of HRDI is to measure wind velocities in the stratosphere and mesosphere during the day and the mesosphere and thermosphere at night with an accuracy of 5 m/sec. HRDI will determine winds by measuring Doppler shifts of atmosphere absorption and emission features. Line of sight winds will be taken in two directions, thus allowing the wind vector to be formed. The HRDI instrument is overviewed. The basis of the measurement is explained, as is an outline of the instrument. Since neither instrument nor observational techniques is fully mature, only a brief sketch is presented.

Description: It has been recognized for some time that water vapor structure visible in infrared imagery offers a potential for obtaining motion vectors when several images are considered in sequence (Fischer et al., 1981). A study evaluating water vapor winds obtained from the VISSR atmospheric sounder (Stewart et al., 1985) has confirmed the viability of the approach. More recently, 20 data sets have been produced from METEOSAT water vapor imagery for the FGGE period of 10-25 November 1979. Where possible, two data sets were prepared for each day at 0000 and 1200 GMT and compared with rawinsondes over Europe, Africa, and aircraft observations over the oceans. Procedures for obtaining winds were, in general, similar to the earlier study. Motions were detected both by a single pixel tracking and a cross correlation method by using three images individually separated by one hour. A height assignment was determined by matching the measured brightness temperature to the temperature structure represented by the FGGE-IIIB analyses. Results show that the METEOSAT water vapor winds provide uniform horizontal coverage of mid-level flow over the globe with good accuracy.

Description: The European Centre for Medium Range Weather Forecasts (ECMWF) is producing operational global analyses every 6 hours and operational global forecasts every day from the 12Z analysis. How the wind data are used in the ECMWF golbal analysis is described. For each current wind observing system, its ability to provide initial conditions for the forecast model is discussed as well as its weaknesses. An assessment of the impact of each individual system on the quality of the analysis and the forecast is given each time it is possible. Sometimes the deficiencies which are pointed out are related not only to the observing system itself but also to the optimum interpolation (OI) analysis scheme; then some improvements are generally possible through ad hoc modifications of the analysis scheme and especially tunings of the structure functions. Examples are given. The future observing network over the North Atlantic is examined. Several countries, coordinated by WMO, are working to set up an 'Operational WWW System Evaluation' (OWSE), in order to evaluate the operational aspects of the deployment of new systems (ASDAR, ASAP). Most of the new systems are expected to be deployed before January 1987, and in order to make the best use of the available resources during the deployment phase, some network studies are carried out at the present time, by using simulated data for ASDAR and ASAP systems. They are summarized.

Description: Two fraternal twin experiments were conducted as part of this study. A data impact experiment using real data (runs 1 and 2) was conducted to assess the impact that rawin wind observations have on both a 5-day assimilation and a single 5-day forecast generated at the end of each assimilation. An observing system simulation experiment (OSSE) using simulated observations (runs 3, 4, and 5) was conducted in order to first calibrate the OSSE results and second to use this calibration to estimate the 'real world' impact from the contribution of global 3-dimensional wind profiles generated from a space-based lidar system known as Windsat. Each of the three runs in the seond experiment were also 5-day assimilation runs with a 5-day forecast initialized from the last 6-hour update cycle of the assimilation. The data impact study revealed a consistent positive impact when rawin winds were added back into an otherwise complete FGGE data set. Both the 6-hour and 5-day forecasts were improved at all levels, in both hemispheres, and for both the wind and the geopotential height fields. Similar results were obtained from the two parallel simulation runs, 3 and 4. Together with the results from runs 1 and 2, calibration coefficients were generated so as to 'correct' the results determined from the addition of Windsat winds (run 5). The Windsat simulation showed a positive improvement in all cases studied. Even though only the tropics were enhanced with these wind observations, hemispheric rms errors were decreased in both the assimilation and 5-day forecast. The 6-hour forecasts of zonal wind from the assimilation run were improved by as much as 50 pct. on the average, and the single forecast showed an average improvement of near 30 pct. Even though these calibrated values are considered too optimistic, the skill of the forecast generated from this run extended the useful forecast period by 18-24 hours.

Description: A series of realistic simulation studies is being conducted as a cooperative effort between the European Centre for Medium Range Weather Forecasts (ECMWF), the National Meteorological Center (NMC), and the Goddard Laboratory for Atmospheres (GLA), to provide a quantitative assessment of the potential impact of future observing systems on large scale numerical weather prediction. A special objective is to avoid the unrealistic character of earlier simulation studies. Following a brief review of previous simulation studies and real data impact tests, the methodology for the current simulation system will be described. Results from an assessment of the realism of the simulation system and of the potential impact of advanced observing systems on numerical weather prediction and preliminary results utilizing this system will be presented at the conference.

Description: A brief review is presented of recent uses of ground-based wind profile data in mesoscale forecasting. Some of the applications are in real time, and some are after the fact. Not all of the work mentioned here has been published yet, but references are given wherever possible. As Gage and Balsley (1978) point out, sensitive Doppler radars have been used to examine tropospheric wind profiles since the 1970's. It was not until the early 1980's, however, that the potential contribution of these instruments to operational forecasting and numerical weather prediction became apparent. Profiler winds and radiosonde winds compare favorably, usually within a few m/s in speed and 10 degrees in direction (see Hogg et al., 1983), but the obvious advantage of the profiler is its frequent (hourly or more often) sampling of the same volume. The rawinsonde balloon is launched only twice a day and drifts with the wind. In this paper, I will: (1) mention two operational uses of data from a wind profiling system developed jointly by the Wave Propagation and Aeronomy Laboratories of NOAA; (2) describe a number of displays of these same data on a workstation for mesoscale forecasting developed by the Program for Regional Observing and Forecasting Services (PROFS); and (3) explain some interesting diagnostic calculations performed by meteorologists of the Wave Propagation Laboratory.

Description: Observational requirements are provided for the 'regional scale' (10(exp 2) to 10(exp 3) km space scale; 3 to 24 h time scale). Given this range, the regional scale represents a spatial and temporal domain in which important scale-interactive processes occur that act to concentrate large vertical wind shears, significant horizontal thermal gradients, and vertical motion patterns into narrow regions. A short review of the mass and momentum adjustments associated with jet streak-induced circulations is discussed. Evidence for the need to specify the wind field in the upper troposphere to accurately simulate forcing for the transverse circulations is also presented. The importance of specifying temperature tendency to resolve the lower tropospheric portion of the transverse circulations is highlighted. The observational requirements are then discussed, along with possible approaches for meeting the requirements on the regional scale.

Description: A passive infrared sensor is described for remote sounding of the wind field in the stratosphere and mesosphere from near Earth orbital spacecraft. The instrument uses gas correlation spectroscopy together with electro-optic phase modulation techniques to measure winds in the 20- to 120-km altitude range globally, both in the day and at night, and with a vertical resolution of better than the atmospheric scale height. Measurement of temperature and the amounts of key atmospheric species may also be made simultaneously and in coincident fields of view with the wind observations. The sensor is currently being developed at the Jet Propulsion Laboratory as a candidate for the upcoming NASA Earth Observation System.

Description: This paper reviews the current status of lidar image correlation techniques of remote wind measurement. It also examines the potential use of satellite borne lidar global wind measurements using this approach. Lidar systems can easily detect spatial variations in the volume scattering cross section of naturally occurring aerosols. Lidar derived RHI, PPI and range-time displays of aerosol backscatter have been extensively employed in the study of atmospheric structure. Descriptions of this type of data can be obtained in many references including Kunkel et al. (1977), Kunkel et al. (1980), Boers et al. (1984), Uthe et al. (1980), Melfi et al. (1985) and Browell et al. (1983). It is likely that the first space-borne lidars for atmospheric studies will observe aerosol backscatter to measure parameters such as boundary layer depth and cloud height. This paper examines the potential application of these relatively simple aerosol backscatter lidars to global wind measurements.

Description: A stated objective for this symposium is to identify requirements for global wind measurements. This paper will draw from recent reports which considered the impact of over 100 environmental factors known to affect military operations. A conclusion that can be drawn from those analyses is that one environmental factor, atmospheric wind, has an operational impact on each of the 48 mission areas examined. This paper will characterize the impact of wind on the various mission areas and will define and summarize both 'technical' and 'operational' requirements for wind intelligence.

Description: There are two theoretical arguments that have been used to discuss the relative importance of mass and wind data in numerical weather prediction (NWP). We will analyze these arguments in this section as clearly as possible in order to draw conclusions which may help to interpret experimental results on four-dimensional data assimilation, simulations of future observing systems, as well as give guidance on how to improve the efficiency with which we use the present observing system.

Description: A low-loss bandstop filter designed and developed for the Deep Space Network's 34-meter high-efficiency antennas is described. The filter is used for protection of the X-band traveling wave masers from the 20-kW transmitter signal. A combination of empirical and theoretical techniques was employed as well as computer simulation to verify the design before fabrication.

Description: A system for the functional testing and simulation of custom and semicustom very large scale integrated (VLSI) chips that are designed using the integrated UNIX-based computer-aided design (CAD) system is described. The testing and simulation system consists of two parts. One of these is a special purpose hardware device that is capable of controlling the digital imputs and outputs on a custom chip. This device, the Digital Microcircuit Functionality Tester (DMFT) system, can be operated by itself or in conjunction with the VAX host computer on the CAD system. The DMFT is integrated into a microprobe station so that these signals can be injected or read from nodes inside the chip, as well as at the pins. The second part of the system is a software package that is installed on the VAX. This software package, logic, includes a full-screen editor for developing chip test sequences and drivers for both the DMFT and the esim logic simulator.

Description: An objective parameterization technique is developed for general nonlinear hydrodynamical systems. The typical structure of hydrodynamical systems, regardless of their complexity, is one in which the rates of change of the dependent variables depend on homogeneous quadratic and linear forms, as well as on inhomogeneous forcing terms. As a prototype of the generic problem containing this typical structure, the parameterization technique is applied to various three component subsets of a five component nonlinear spectral model of forced, dissipative quasi-geostrophic flow in a channel. The results obtained lead to specification of the necessary data coverage requirements for applying the technique in general.

Description: A steady, axisymmetric model of the general circulation is developed as a basis for climate stability studies. The model includes the effects of heating, rotation, and internal friction, but neglects topography. It is assumed that the axisymmetric flow may be modeled by making the Boussinesq and deep convection approximations. The hydrostatic assumption is not made, thus permitting the advective terms to be included in the vertical equation of motion. The initial set of five primitive equations is reduced to three equations in terms of the zonal velocity, meridional streamfunction, and the potential temperature perturbation. The application of the Boussinesq, deep convection, and quasi-geostrophic assumptions limits the ranges of the heating and rotation rates. For values not too far from typical atmospheric values, the model produces a stability boundary separating Hadley from Rossby flow. The boundary is characterized by a particular value of vertical wind shear, which suggests that baroclinic instability is the primary mechanism for the loss of stability. The initial growth rates are largest for longitudinal waves 4-7, also in agreement with studies of baroclinic instability.

Description: A two layer spectral quasi-geostrophic model is used to simulate the effects of topography on the equilibria, their stability, and the long term evolution of incipient unstable waves. The flow is forced by latitudinally dependent radiative heating. Dissipation is in the form of Rayleigh friction. An analytical solution is found for the propagating finite amplitude waves which result from baroclinic instability of the zonal winds when topography is absent. The appearance of this solution for wavelengths just longer than the Rossby radius of deformation and disappearance of ultra-long wavelengths is interpreted in terms of the Hopf bifurcation theory. Simple dynamic and thermodynamic criteria for the existence of periodic Rossby solutions are presented. A Floquet stability analysis shows that the waves are neutral. The nature of the form drag instability of high index equilibria is investigated. The proximity of the equilibrium shear to a resonant value is essential for the instability, provided the equilibrium occurs at a slightly stronger shear than resonance.

Description: Estimates of cloud street geometry produced by a model of the parallel/thermal instability modes of shallow convection are compared with observations obtained during the 1981 KonTur experiment. Good agreement between the modeled and observed orientation angles, wavelengths and Reynolds numbers are found when the streets are assumed to derive their energy from the average shear and the lowest order sine terms of a Fourier expansion of the mean wind profile (or equivalently from the lowest order cosine terms of the mean shear profile). The modes associated with the cosine terms of the wind profile (or the sine terms of the wind shear profile) do not agree well with the observations. These results suggest that the boundary layer rolls observed during KonTur might have developed owing to a combined parallel/thermal instability originating primarily from the cosine terms of the ambient roll parallel wind shear.

Description: Characterization tests were carried out at three charge levels and four discharge levels. The "c' or capacity of the battery is designated at 6.5 ampere-hours. The recharge ampere-hours was the same for all test conditions, 6.5 A-H, regardless of the discharge capacity removed for any particular discharge rate. Less capacity can be removed at higher discharge rates to the same termination voltage, which was 0.50 volts for the weakest (lowest voltage) cell. The general trend of efficiencies increases as the charge rate increases as noted in results of the table included in the handout package. The data also indicate the efficiency increases as the discharge rate decreases. This is true; however, efficiencies at the discharge rates of c and 2c are penalized because these cycles received more overcharge than necessary.

Description: The probability of Ni-Cd battery survival was determined by researching survival data on cells fabricated from 1964-1977. A log of cell failure times were plotted against cumulative failure percentage and mean and standard deviation were determined.

Description: The design of long life, low weight nickel cadmium cells is studied. The status of a program to optimize nickel electrodes for the best performance is discussed. The pore size of the plaque, the mechanical strength and active material loading are considered in depth.

Description: An evaluation of the current nickel hydrogen cell design is presented. The IPV, or the Individual Pressure Vessel, is the state of the art right now. The present design, 3 1/2 inch cell, has a current limit of 50 ampere-hours. The nickel hydrogen cell design is the state of the art. Its size is 3 1/2 inches which limits it to 50 hours. The probable limits of that are probably 160 amphere IPV cell remaining in the passive cooling mode. The IPV stacks is a parallel connection of electrodes. Positive electrodes are connected with leads to the top portion of the stack and negative electrodes are connected with leads and pulled down to the bottom. So it is a combination connection of paralleling series electrostacking--parallel inside each individual stack, and series connected from one stack to the next. It offers, in the analysis, improvements in packaging, cost, energy density, and specific energy.

Description: Nickel Hydrogen cell and battery technology has matured to the point where a real choice exists between Nickel Hydrogen and Nickel Cadmium batteries for each new spacecraft application. During the past few years, a number of spacecraft programs have been evaluated at Hughes with respect to this choice, with the results being split about fifty-fifty. The following paragraphs contain criteria which were used in making the battery selection.

Description: The Defense Research Establishment Ottawa (DREO) has been studying the nickel-cadmium system, both vented and sealed, since the early 1950's. Reasonable success has been achieved in a wide variety of applications covering: military vehicle use under Arctic conditions; high performance military aircraft; manpacked communications sets; remote standby power and small portable instrumentation. Early studies on the vented system for high rate vehicle and aircraft cranking applications proved useful in later studies on the sealed NiCd system. This was especially true in the areas of plate loading and electrolyte composition. To achieve high rate cranking currents of 20C to 30C, it was necessary to have light to moderate plate loadings, a large reactive surface area, and electrolyte of optimum conductivity. DREO undertook some fundamental studies to understand the system from the inside out rather than test cells from the outside and then analyze their components. The conclusions of these studies were incorporated into the Procurement Specification for Ni-Cd cells ISISA Spec S615-P-2. A brief comment will be made on the choice of cell design and how some of the factors of cell manufacture could affect cell performance.

Description: Events from the development and orbital flight experience with a nickel hydrogen battery are described. The events highlight characteristics of nickel hydrogen which afford superior capability in overcharge, overdischarge and state of charge evaluation, when compared to the nickel cadmium electrochemical system. Some developments in nickel hydrogen technology that provide the potential of furthering nickel hydrogen superiority for satellite applications are also discussed.

Description: Ni-H2 batteries are just now being put into service. All of the remaining INTELSAT V satellites (approximately 10), starting with the next to be launched in early 1983, will use Ni-H2 batteries. In addition, the next generation of INTELSAT VI satellites, and probably INTELSAT VII and VIII, will use Ni-H2 batteries. This means that international telecommunications satellites will use Ni-H2 batteries through the 1990's. It is projected that the lifetime of these batteries will be greater than 10 years at deep depth-of-discharge (DOD), and that the battery subsystem will no longer limit satellite lifetime or communications capability during eclipse periods. This paper discusses the advantages of the Ni-H2 battery, as compared with the Ni-Cd battery, for telecommunications satellites.

Description: Nickel-hydrogen cells appear to be an improvement over the nickel-cadmium in applications requiring longer lifetime and reduced weight. An even more efficient couple, the silver-hydrogen couple, is also considered. After a theoretical study first performed by the Battelle Institute of Geneva under ESA (European Space Agency) contract, SAFT has undertaken more detailed analyses of the silver-hydrogen degradation mechanisms. ESA and the French Department of Defense contracted with SAFT for a full-development program of the silver-hydrogen technology.

Description: This effects of reconditioning on the performance of NiCd batteries are reviewed. These effects are correlated with cell experiments and individual electrode investigations. The effects of reconditioning on the positive electrode performance are found to be significant. A mechanism is proposed that rationalizes the operation of the nickel electrode and suggests that reconditioning minimizes depth of discharge stress during use and maintains uniformity of the active material.

Description: Cost considerations for spacecraft battery reconditioning are studied. Results indicate that the cost of performing reconditioning is minuscule compared with spacecraft system investment. Results also indicate that spacecraft life extension of a few days justifies incorporation of reconditioning circuitry.

Description: Six (6) geostationary spacecraft, manufactured by RCA Astro, are presently operating in orbit. All of their batteries are performing well. They all contain unique battery reconditioning circuitry, permitting individual cell reconditioning to practically zero volts without the danger of cell reversal. This reconditioning is performed just prior to start of each eclipse season. This technique has maintained the battery's end-of-discharge voltage with mission life. The oldest operating RCA Astro geostationary spacecraft, Satcom F1 and F2, have now completed almost 7 and 6-3/4 years in orbit, respectively. Their battery performance, reported herein, show that a major milestone in the mission longevity of nickel-cadmium batteries has heen achieved. Low earth orbit test data show a long lasting effect of maintaining end-of-discharge voltages for nickel cadmium cells using periodic reconditioning. The unique RCA light-weight reconditioning circuitry can accomplish a quick reconditioning and prevent cell reversal. Reconditioning, thus, has the potential for extending mission life of geostationary as well as low earth orbit spacecraft, when two or more batteries are present.

Description: Deep-discharge reconditioning (DDR) can be of great benefit to battery performance, especially in geosynchronous orbit, if performed properly and regularly, and can be essential to operation of batteries at the high depths of discharge (DOD) required to minimize weight. The procedure should be tailored to fit the nature of the degradation occuring during regular cycling. DDR is not without its drawbacks, however, and these differ depending on the normal DOD to be sustained and/or whether the discharge is done at the battery or the cell level. Battery-level discharge carries the minimum weight penalty but raises questions of the effects of low-rate cell reversal that as yet have no firm answers. Cell level discharge avoids cell reversal but carries significant penalties of weight and complexity. Thus no universal procedure or method of implementation of deep-discharge reconditioning is now available and thus the various approaches must be evaluated for each application.

Description: It is argued that sophisticated battery control systems are required to support the high power, high energy spacecraft secondary battery systems of the post 1985 time period. Four categories of battery control system functions are defined and discussed: battery operational control, auxiliary system control, battery system status indication and fault detection fault isolation. A concept for implementation of such a control system is also presented and discussed.

Description: A comparison of voltage limited control methods limit control methods for fixed array and oriented array missions is given. The LANDSAT D, Earth Radiation Budget Experiment and Solar maximum Mission techniques are compared.

Description: Battery charge control for orbiting spacecraft with mission durations from three to ten years, is a critical design feature that is discussed. Starting in 1974, the General Electric Space Systems Division designed, manufactured and tested battery systems for six different space programs. Three of these are geosynchronous missions, two are medium altitude missions and one is a near-earth mission. All six power subsystems contain nickel cadmium batteries which are charged using a temperature compensated voltage limit. This charging method was found to be successful in extending the life of nickel cadmium batteries in all three types of earth orbits. Test data and flight data are presented for each type of orbit.

Description: A simple non-linear circuit model for battery behavior is given. It is based on time-dependent features of the well-known PIN change storage diode, whose behavior is described by equations similar to those associated with electrochemical cells. The circuit simulation computer program ADVICE was used to predict non-linear response from a topological description of the battery analog built from advice components. By a reasonable choice of one set of parameters, the circuit accurately simulates a wide spectrum of measured non-linear battery responses to within a few millivolts.

Description: A generalized code applicable to many different electrochemical systems and geometric designs is discussed. The code is to be set up so that physical property data such as thermal conductivity, viscosity, density, and configuration (e.g. physical dimensions) are the input data. Thus, by changing these parameters many different battery configurations can be handled. The outputs, as a function of time and space, are voltage, current, temperature, pressure, velocity, and species concentration.

Description: Previous work is refined and extended to describe the discharge curve of Ni-Cd cells. Several models are discussed which are based on chronopotentiometry theory and on a thermodynamic approach. Emphasis is placed on improvement of the fit for the initial portion of discharge. Equations are presented which improve the fit for all regions of the discharge curve.

Description: A model to simulate nickel-cadmium battery performance and response in a spacecraft electrical power system energy balance calculation was developed. The voltage of the battery is given as a function of temperature, operating depth-of-charge (DOD), and battery state-of-charge. Also accounted for is charge inefficiency. A battery is modeled by analysis of the results of a multiparameter battery cycling test at various temperatures and DOD's.

Description: Using the accelerating rate calorimeter, the hazards associated with exothermic reactions occurring in Li/SO2 cells under the conditions of discharge, forced overdischarge, resistive overdischarge, and forced overdischarge at low tempratures are quantitatively defined in terms of: rate of pressure generation, overall pressure rise, rate of temperature, and overall heat generation. Consistent with the findings of other investigators, it is believed that the major reactions contributing to Li/SO2 cell exothermicity are: the lithium/acetonitrile reaction, the thermal decomposition of lithium dithionite, and the lithium/sulfur reaction.

Description: Cell design criteria were established which can result in a safe lithium/thionyl chloride cell. A cell vent, a low area internal anode cell, cell balance and composition of the cathode-electrolyte solution were found to be important factors in the design of a safe cell. In addition to routine testing, both undischarged and discharged cells were subjected to electrical abuse, environmental abuse and mechanical abuse without disassembly.

Description: The roll of general cell design characteristics in preventing hazardous reactions during voltage reversal of lithium cells is discussed. Anode limited versus cathode limited design and case positive versus case negative design are addressed.

Description: The ovedischarge test program and results for double A and D lithium cells are discussed. Temperature increases and sparking responses are dressed.

Description: Lithium cell performance at extremely low temperatures was tested and materials which could be used to make a cell completely electro-chemically inert for the purpose of deactivation were investigated. The effects of temperature and current density on polarization and performance loss are discussed along with discharge recovery behavior.

Description: Lithium batteries offer many advantages for Navy systems but may also exhibit undesirable hazardous behavior. Safety problems have been traced to a variety of chemical and physical causes. The Navy has established a central safety office with responsibility for all lithium battery use. Before an item is approved for Navy use, it must pass both a design review and a set of end item tests. These reviews focus on complete systems which include a battery inside the end item. After system approval, specific regulations govern the transportation, storage, and disposal of the unit containing lithium batteries. Each of these areas is discussed in detail.

Description: The unique power requirement of NASA's Galileo Jupiter Probe are most readily met by a Li/SO2 battery; however, because this battery system is not space flight proven, extensive effort was required to qualify this device from the stand point of performance and safety. Due to the rather checkered safety record of the Li/SO2 system, safety has been foremost among the design considerations and has been addressed at the cell, battery and system level. The mission requirements which led to the choice of the Li/SO2 battery and the safety engineering which went into the battery and power system design are described.

Description: Results of an experiment investigating overdischarge behavior of two types of Li/SO2 cells are presented. Forced overdischarges of the Li/LiBr, CH3CN/SO2 cell can result in unsafe behavior such as venting with fire and release of toxic gases. The hazards may be minimized or eliminated by careful cell design considerations and practice of high standards of quality contol in cell manufacture. Seemingly safe cells at 25 C when forced overdischarged at -25 C, even at low currents, exhibited incipient signs of hazards. Their cathodes indicated signs of shock sensitivity. Cathode limited Li/SOCl2 cells were safe during forced overdischarge for long periods of time. Lithium limited Li/SOCl2 cells in which practically all Li had been used up before cell reversal did not exhibit hazardous behavior. Anode limited Li/SOCl2 cells, but not Li limited, exhibited detonations, all during overdischarges at relatively low current densities of or = 1 mA/sq cm 2. Anode potentials 4v with large oscillations preceeded the events. The events were confined to the anode and the temperature rose high enough to melt Ni grids.

Description: In order to determine whether larger size lithium batteries would be commercially marketable, the performance of several D size lithium batteries was compared with that of an equivalent alkaline manganese battery, and the relative costs of the different systems were compared. It is concluded that opportunities exist in the consumer market for the larger sizes of the low rate and moderate rate lithium batteries, and that the high rate lithium batteries need further improvements before they can be recommended for consumer applications.

Description: Case histories were described of hazardous behavior for three different cell sizes ranging in nominal capacity from 300 mAh to 12,000 Ah. Design characteristics and other facts believed to have been responsible for the cell explosions, are presented. Obvious facts are discussed as causes for hazardous behavior of lithium batteries in general and oxyhalide batteries in particular.

Description: The joint airport weather studies (JAWS) project is discussed. The major objectives of the JAWS Project are a fundamental description of the phenomenon, a determination of the hazard potential and a definition of a protection and warning system, all of which are relative to low level wind shear. Aspects of the low level wind shear phenomenon. The principal focus, however, is the microburst. The microburst is fundamentally a rather simple atmospheric flow. It is a downdraft that, upon approaching the surface, spreads out horizontally, producing a diverging radial flow in all directions. For any direction that an aircraft flies through the microburst, it will first encounter increasing head winds; then the remnants of the downdraft; and then, increasing tail wind.

Description: A heavily instrumented F-106B aircraft was flown in thunderstorms to gather data for characterizing lightning at aircraft operating altitudes. Conventional weather finding techniques are supplemented with UHF lightning mapping radar to select the most active storm cells and the most likely altitude for obtaining direct lightning strikes to the airplane. One hundred seventy-six strikes were obtained in a 3 year period, mostly at an altitude of above 25,000 feet.

Description: A wind shear and vortex wake and their impact on aircraft were investigated. The systems and advice to help pilots, and rational scientific methods to assist in advising certification authorities and those interested in improving flight safety were developed. Wind Shear and Vortex Wakes are related, they are both invisible enemies of aircraft in the form of large disturbances in the atmosphere, both cause major accidents. Problems of building wakes at airports are is considered. Research on wind shear was initiated by the American FAA following the Boston, New York and Denver accidents to civil airliners. This resulted in: useful advice to pilots about wind shear; better attempts by the meteorologists at forecasting wind shear conditions; and useful ideas for wind shear measurement and warning systems. Three major research tasks are outstanding: (1) Worldwide measurements to give reliable estimates of probability and details of the forms of large wind shears; (2) Developments of real time wind shear measuring systems for ground or airborne use; and (3) Establishing relationships between measured wind shear and the potential hazard to an aircraft, or class of aircraft.

Description: Marked surface inversions occur most frequently in dry continental climates, where low atmospheric humidity allows heat transfer by long wave thermal radiation. In the northern latitudes, surface inversions reach their maximum intensity during the winter, when the incoming Sun's radiation is negligible and radiative cooling is dominant during the long nights. During winter, air mass boundaries are sharp, which causes formation of marked surface inversions. The existence of these inversions and sharp boundaries increase the risk of wind shear. The information should refer to marked inversions exceeding a temperature difference of 10 deg C up to 1000 feet. The need to determine the temperature range over which he information is operationally needed and the magnitude of the inversion required before a notification to pilots prior to departure is warranted are outlined.

Description: The Gust Gradient Program is a data intensive effort involving tripple Doppler radar, a surface weather station mesonet and other aircraft. The Joint Airport Weather Studies was utilized to gain additional data. The data were used to fill in the gap in turbulence modeling.

Description: The objective of the Generalized Exponential Markov (GEM) Program was to develop a weather forecast guidance system that would: predict between 0 to 6 hours all elements in the airways observations; respond instantly to the latest observed conditions of the surface weather; process these observations at local sites on minicomputing equipment; exceed the accuracy of current persistence predictions at the shortest prediction of one hour and beyond; exceed the accuracy of current forecast model output statistics inside eight hours; and be capable of making predictions at one location for all locations where weather information is available.

Description: Recommendations based on need, cost, and achievement of flight safety are offered, and the re-evaluation of weather parameters needed for safe landing operations that lead to reliable and consistent automated observation capabilities are considered.

Description: The primary responsibilities of the National Weather Service (NWS) are to: provide warnings of severe weather and flooding for the protection of life and property; provide public forecasts for land and adjacent ocean areas for planning and operation; and provide weather support for: production of food and fiber; management of water resources; production, distribution and use of energy; and efficient and safe air operations.

Description: The implementation of the National Airspace System (NAS) will improve safety services to aviation. These services include collision avoidance, improved landing systems and better weather data acquisition and dissemination. The program to improve the quality of weather information includes the following: Radar Remote Weather Display System; Flight Service Automation System; Automatic Weather Observation System; Center Weather Processor, and Next Generation Weather Radar Development.

Description: Rainfall characteristics using data from dense recording raingage networks is reviewed. Data from such networks have quantified temporal and spatial rainfall distributions, and have supplied specialized information about local and orographic effects. The natural variability, temporally and spatially, for annual, seasonal, monthly, and individual events is treated. Especially important are the spatial variations of precipitation as a function of synoptic type, precipitation type, amount, and duration. Results from dense raingage networks in Illinois, and some data from other climatic regions is also treated.

Description: A 10 channel scanning radiometer, built as a prototype for the coastal zone color scanner on the Nimbus 7 satellite, was flown on a high altitude aircraft during a Gymnodium breve bloom along the west coast of Florida. The remotely measured ocean color imagery shows what is probably the patchy structure of a G. breve bloom extending over a 60 km by 100 km area. This conclusion is based on visual inspection of bathymetry to infer bottom reflection trends and on a single growth truth measurement of B G. breve obtained the previous day. The image shows coherent blooms which extend scales up to 60 km in length.

Description: The snowmelt-runoff model developed for two small central European watersheds simulate daily streamflow on the 228 sq km Dinwoody Creek basin in Wyoming, using snowcover extent for LANDSAT and conventionally measured temperature and precipitation. For the six-month snowmelt seasons of 1976 and 1974, the simulated seasonal runoff volumes were within 5 and 1%, respectively, of the measured runoff. Also the daily fluctuations of discharge were simulated to a high degree by the model. Thus far the limiting basin size for applying the model has not been reached, and improvements can be expected if the hydrometeorological data can be obtained from a station inside the basin. LANDSAT provides an efficient way to obtain the critical snowcover input parameter required by the model.

Description: A large scale numerical time-dependent model of sea ice that takes into account the heat fluxes in and out of the ice, the seasonal occurrence of snow, and ice motions was used in an experiment to determine the response of the Arctic Ocean ice pack to a warming of the atmosphere. The degree of warming specified is that expected for a doubling of atmospheric carbon dioxide with its associated greenhouse effect, a condition that could occur before the middle of the next century. The results of three 5-year simulations with a warmer atmosphere and varied boundary conditions were: (1) that in the face of a 5 K surface atmospheric temperature increase the ice pack disappeared completely in August and September but reformed in the central Arctic Ocean in mid fall; (2) that the simulations were moderately dependence on assumptions concerning cloud cover; and (3) that even when atmospheric temperature increases of 6-9 K were combined with an order-of-magnitude increase in the upward heat flux from the ocean, the ice still appeared in winter. It should be noted that a year-round ice-free Arctic Ocean has apparently not existed for a million years or more.

Description: During the summer of 1977, fire totaled 44 sq km of tundra vegetation according to measurements using LANDSAT imagery. Based on the experience gained from analysis of this fire using ground observations, satellite imagery, and topographic maps, it appears that natural drainages form effective fire breaks on the subdued relief of the Arctic coastal plain and northern foothills. It is confirmed that the intensity of the fire is related to vegetation type and to the moisture content of the organic rich soils.

Description: The geostationary and polar satellites comprising the current operational system are discussed. The data acquisition capabilities of both satellite types and their complementary functions are reviewed. The advanced very high resolution radiometer on the TIROS N satellites is particularly addressed along with the imaging and atmospheric sounding instrumentation aboard the GOES satellites. The dissemination of the satellite data to the prospective users is also discussed.

Description: Snow accumulation and depletion at specific locations can be monitored from space by observing related variations in microwave brightness temperatures. Using vertically and horizontally polarized brightness temperatures from the Nimbus 6 electrically scanning microwave radiometer, a discriminant function can be used to separate snow from no snow areas and map snowcovered area on a continental basis. For dry snow conditions on the Canadian high plains, significant relationships between snow depth or water equivalent and microwave brightness temperature were developed which could permit remote determination of these snow properties after acquisition of a wider range of data. The presence of melt water in the snowpack causes a marked increase in brightness temperature which can be used to predict snowpack priming and timing of runoff. As the resolutions of satellite microwave sensors improve the application of these results to snow hydrology problems should increase.

Description: Methods using snowcovered area to update seasonal forecasts as snowmelt progresses are also being used in quasi-operational situations. The input of snowcovered area to snowmelt models for short term perdictions was attempted in two ways; namely, the modification of existing hydrologic models and/or the use of models that were specifically designed to use snowcovered area. A daily snowmelt runoff model was used with LANDSAT data to simulate discharge on remote basins in the Wind River Mountains of Wyoming. Daily predicted and actual flows compare closely, and, summarized over the entire snowmelt season (April 1 - September 30), the average difference is only three percent. The model and snowcovered area data are currently being tested on additional watersheds to determine the method's transferability.

Description: Presumably caused by lightning, a large fire occurred due east of Point Lay several kilometers southwest of the Kokolik River, the farthest north a fire was ever fought by Bureau of Land Management personnel in Alaska. The progress and area extent of the fire were determined by analysis of LANDSAT MSS band 5 and 7 imagery. Low altitude observations from helicopter showed the fire burned a range of vegetation and relief types which included low polygonized and upland tussock tundras. The burned area appeared wetter on the surface than the unburned area, due to a lack of moisture absorbing organic matter and the possible release of moisture from the deeper thawed zone. Suggestions for future investigations of the effects of fire on tundra and permafrost terrains are discussed.

Description: Programs for the development and operation of meteorological satellites from the TIROS 1 satellite and the establishment of NASA through the 1960's are described. The technical problems confronted in the development of the early satellite systems are discussed in addition to issues in international involvement and program support. The TIROS and Nimbus series satellites are primarily addressed.

Description: By using the most complete available records of direct beam radiation and volcanic eruptions, an historical analysis of the role of the latter in modulating the former was made. A very simple fallout and dispersion model was applied to the historical chronology of explosive eruptions. The resulting time series explains about 77 percent of the radiation variance, as well as suggests that tropical and subpolar eruptions are more important than mid-latitude eruptions in their impact on the stratospheric aerosol optical depth. The simpler climatic models indicate that past hemispheric temperature can be stimulated very well with volcanic and CO2 inputs and suggest that climate forecasting will also require volcano forecasting. There is some evidence that this is possible some years in advance.

Description: Visible and infrared pictures from two Geostationary Operational Environmental Satellite Systems satellites, in circular orbits at about 19,000 nautical miles, are available continuously at approximately 30 minute intervals. Still pictures and film loops from this system vividly depict the events associated with the May 18, 1980 eruption of Mount St. Helens. The initial explosion, shock wave, and visible horizontal dust distribution during the following week are readily apparent. Meteorological wind and height fields permit the inference of the vertical distribution of volcanic dust as well as explain the atmospheric behavior which caused the visible and nonvisible dust distribution.

Description: Examples of the use of geostationary satellites in meteorology are given. Studies of the rate of change of cumulus clouds and cloud systems and wind parameter determination from cloud motions are reviewed. Computer processed imagery products are also discussed.

Description: The Defense Meteorological Satellite Program is described with particular emphasis on the military applications of METSAT data. Satellite operational support, data processing and image quality requirements are discussed.

Description: A historical overview of the pioneer projects for the development of meteorological satellites is given. In addition, the parallel development of the responsible space agencies and panels is addressed. The Vanguard 2 satellite, the first Earth radiation experiment, and the vidicon equipped TIROS-1 satellite are discussed.

Description: A brief review of the effects of climate and weather on the 1980 Mount St. Helens eruptions and the subsequent dispersion of ash and gases and the reciprocal influences of the eruptions on climate and climatology is presented. The effects of mesoscale destruction of snow fields and vegetation, a revised mountain profile, and ash deposits are addressed along with impacts on hemispheric climate and disruption of normal climatological observations, in the areas directly affected by the explosions and ashfall. Environmental and economic consequences are also considered.

Description: The working group agreed that the first (primary) objective should be the determination of methods for the accurate measurement of total rain water and total cloud water with passive microwave methods. There was no argument on the points concerning nonlinear relationships between T sub B and rain rate (R) over the range of important rain rates (half of oceanic rainfall occurs at rates greater than 15 mm h-1), such that variations in rain rate within a footprint lead to an incorrect measurement of the average rate for that footprint, and one cannot determine the characteristics of the sensed rain area. This is especially true near 18 GHz, where the dynamic range above 15 mm h-1 is very small because this frequency does not clearly fall in either a scattering regime or emissive regime at these wavelengths. It is also not clear whether very low frequency (emissive) techniques will be the best at measuring rain processes, or high frequency (scattering) techniques, where precipitation-size ice plays a major role in the signal attenuation. It is still not known what signal of rain is at certain rates on an observational basis because of the many different conditions that can exist within a single satellite observed footprint.

Description: The data collection phase of a Doppler wind measurement experiment supported by high-resolution Jimsphere/FPS-16 wind data and Windsonde data was carried out at the Kennedy Space Center in February, March and early April of 1985. The Doppler wind measurements were made using a hybrid doppler profiler put in place by the Johnson Space Center and a SOUSY profiler operated by Radian Corporation. Both systems operated at 50 Mhz. Although the doppler profiler systems were located 10 km apart to enable concurrent operation of the systems for data comparison, little concurrent data were obtained due to set-up delays with the SOUSY system, and system problems with the WPL system during the last month of the test. During the test period, special serial Jimsphere soundings were taken at two-hour intervals on six days in March and April in addition to balloon soundings taken in support of the Shuttle launch operations. In addition, there is temperature, moisture and wind information available from the daily morning Radiosonde sounding taken at the Kennedy site. The balloon release point was at the same location as the SOUSY profiler. Vertical resolution of the SOUSY profiler was 150 M to approximately 20 km. The vertical resolution of the WPL profiler was 290 M to 10 km and 870 M to 17 km. Winds determined form the Jimsphere balloon have a vertical resolution of 30 M.

Description: The Atmospheric Sciences Division (ASD) of the Systems Dynamics Laboratory at NASA's Marshall Space Flight Center (MSFC) is currently involved in interactive information processing for the Mesoscale Analysis and Space Sensor (MASS) program. Specifically, the ASD is engaged in the development and implementation of new space-borne remote sensing technology to observe and measure mesoscale atmospheric processes. These space measurements and conventional observational data are being processed together to gain an improved understanding of the mesoscale structure and the dynamical evolution of the atmosphere relative to cloud development and precipitation processes. To satisfy its vast data processing requirements, the ASD has developed a Researcher Computer System consiting of three primary computer systems which provides over 20 scientists with a wide range of capabilities for processing and displaying a large volumes of remote sensing data. Each of the computers performs a specific function according to its unique capabilities.

Description: During FY-85 the data gathering process was completed. This gave researchers a reasonably complete picture of the Shuttle's operational weather support units and requirements. They expanded on the site visits of FY-84 with telephone follow-up. They finalized recommendations and wrote the final report. The final report was accepted by NASA and has been published as NASA Contractor Report CR-171418.