ALBERT

Description: Since much attention has been paid to the targeted drug delivery system, using the molecular dynamics simulation, the present work has been devoted to clarify the potential of the silicon carbide nanotubes (SiCNTs) as a new carrier for the three common anti-cancer drugs temozolomide, carmustine, and cisplatin. Three zigzag single-walled nanotubes with different diameters, i.e. SiC(18,0), SiC(20,0), and SiC(22,0), in pure and decorated with the hydroxyl and carboxyl functional groups are selected to assess the effect of the functional groups as well as the diameter effect on the drug encapsulation process. The effects of binding energy, probability of finding the drugs along the nanotube length, mean square displacement, and body temperate as well as the zeta potential for the stability of the drug delivery system in the blood stream are evaluated. The results showed that the cisplatin does not encapsulate into the selected SiCNTs. However, the pure nanotubes show a high stability in the blood stream but the magnitude of their interaction energies with the temozolomide and carmustine drugs is less than −10 kcal mol−1, which does not guarantee that the drug will remain bonded to the nanotubes in the blood stream. Also the presence of the carboxyl functional group on the nanotube surface not only has no significant effect on the interaction energies but also decreases the stability of the drug delivery system. Decorating the edge nanotubes with the hydroxyl group causes the interaction between temozolomide and SiCNTs into chemisorption (−10 to −40 kcal mol−1) while the variation in binding energy of the carmustine is not remarkable. Finally, the zeta-potential results showed that the edge nanotubes decorated with the hydroxyl group due to a high stability in the blood stream as well as the strong interaction with the drugs temozolomide and carmustine is an appropriate carrier for the targeted drug delivery.

Description: Mo/alumina cermet-based selective coatings are of great interest for concentrated solar-thermal power systems, in particular, parabolic trough collectors. We report on the sputter deposition of high-performance multilayer Mo/alumina cermet coatings on stainless steel with a solar absorptance of 94% and a thermal emittance of 8% (at 400 °C), and excellent thermal stability. The selective coatings were deposited in a 0.95 m3 sputtering chamber in order to correlate the deposition parameters, such as presence of residual gases, deposition power, and sputtering method (DC or RF), with the coating composition and the resulting optical properties. X-ray photoelectron spectroscopy, x-ray diffraction, and Raman spectroscopy have been applied to quantitatively describe the effect of residual oxygen on the distribution of oxidation states of Mo in the metallic infrared reflector layer, the high and low metallic volume fraction cermet layers, as well as the composition of the alumina top layer. The results provide strategies to obtain optimal selective coatings under conditions where residual oxygen cannot be avoided, which are essential for a successful transition from a laboratory to pre-industrial scale of vacuum deposition systems.

Description: This paper presents the effect of the variations of multi-walled carbon nanotube (MWCNT) modification in shape memory polymer hybrid composites concerning their mechanical, thermomechanical, and shape memory characterizations. The process of fabrication includes preparation of the MWCNT/epoxy hybrid nanocomposites by shear mixing, ultrasonication, magnetic stirring, and subsequent molding by hand layup method. The appropriate post-processing was performed for the curing and cutting to prepare the samples for the mechanical and thermomechanical characterizations as per the ASTM standards. An enhancement in the thermomechanical properties was noticed due to the incorporation of the MWCNT. These observations were also validated with improvement in the interfacial bonding between the carbon fiber and the modified matrix, as shown in the morphological fractography. The tensile strengths were improved by 18%, 39%, and 26% with the incorporation of 0.4%, 0.6%, and 0.8% modified MWCNT nanocomposites as compared to pure unmodified SMPC. However, the shape recovery of all the configurations of the shape memory polymer hybrid composites was not compromised on polymer-modified remaining almost unchanged at 94%.

Description: The influence of deep cryogenic treatment on the erosive wear performance of Stainless Steel-316L (SS-316L) used in hydropower plants is studied. For this purpose, several SS-316L samples were held at deep cryogenic temperatures (−196 °C) for different soaking periods (12, 24, 36 h). The erosive wear tests were conducted on a self-fabricated slurry erosion test rig and the same was evaluated by weighing the cumulative mass loss (CML) of samples for every 30 min post erosion. From experimental analysis, it was found that the erosive wear was found to be minimum and the hardness reaches to maximum value after 24 h of the soaking period which could be attributed to the significant microstructural changes such as the transformation of γ-austenite phase into (δ-ferrite+α′-martensite) along with precipitation of numerous carbides after deep cryogenic treatments.

Description: Performance of MOF-derived micrometer porous Fe2O3 as the oxidizer in Zr-fuelled thermite is compared with commercial nano-sized Fe2O3 by characterizing thermal and combustion behavior of Fe2O3/Zr mixture via differential scanning calorimetry, optical emission measurement as well as composition and morphology analysis on condensed combustion products. Results show that thermal behaviors of Fe2O3/Zr with a slow heating rate have little difference regardless of the kind of Fe2O3. However, MOF-derived micrometer porous Fe2O3 show an obvious superiority in enhancing combustion of Fe2O3/Zr heated by a high rate. Combustion reactions of Fe2O3/Zr under high heating rates are probably rate-controlled by condensed reaction. The better performance of MOF-derived Fe2O3 is attributed to its larger contact area with Zr particle in that micrometer porous Fe2O3 particles are easily broken into primitive nano-sized particles, which effectively avoid the agglomeration of oxidizer. The MOF-derived Fe2O3 particles obtained at calcination temperature of 550 °C enable the best combustion performance of Fe2O3/Zr thermite. This should be because the crystallinity and porous structure of 550 °C-Fe2O3 are more favorable for the mass transfer process during high-rate combustion.

Description: Friction stir welding (FSW) process is the preferred technique for joining of dissimilar metals. This paper intends to provide comprehensive study on the mechanical and metallurgical properties of dissimilar friction stir welded aluminium alloys, AA6061 and AA5052. The objective of the study is to find the optimum welding parameters at which the maximum weld joint strength can be achieved and to identify the influence of those parameters on the weld strength and microstructure of the AA6061 with AA5052 welded joints. The FSW process parameters such as traverse speed, tool rotational speed, axial force and tilt angle were considered. The mechanical properties measured are yield strength, tensile strength and percentage of elongation. Scanning Electron Microscopy (SEM) and optical microscope were used to observe the microstructure of weld zone (WZ) and heat affected zone (HAZ) of welded samples. Energy Dispersive x-ray Analysis (EDS) was used to obtain the elemental composition at the weld zone. Visual inspection reveals that there is no existence of weld defects like voids and porosity developed on the surface of the joints. The welds produced by the dissimilar aluminium alloys exposed an equiaxed and fine-grained structure in the weld zone. Analysis of variance (ANOVA) Technique is used to check the adequacy of the developed mathematical model. The difference between calculated and adjusted R2 is 0.2 which indicates that the model is adequate. The percentage error is also less for the estimated and predicted values of the properties of welded joints.

Description: Olive oil production processes breed two kinds of environmentally detriment waste by-products; the solid olive residue (SOR) and olive waste water (OWW) by-products. The current work aims to treat simultaneously both wastes in the same location. The solid olive residue was converted to activated carbon with pyrolysis at 600°C, followed by steam activation at 600, 700 and 800°C. The produced activated carbons were investigated by FTIR, SEM, BET surface areas analyzer and iodine number. The surface area increases with increasing stream activation temperature up to 800°C (1020 m2/g BET). However, steam activation at 700°C is most environmental and economically feasible, because increasing the activation temperature from 700 to 800°C increases the surface area only from 979 to 1020 m2/g. Activated carbon steam cured at 700°C shows high removal capacity of both polyphenolic compounds and COD of OWW. 95.5% of COD and 84.2% of polyphenolic compounds was removed after equilibrium with activated carbon for 2 hours at room temperature.

Description: Thickness-shear (TSh) vibration of a rectangular piezoelectric crystal plate is studied with the consideration of flexoelectric effect in this paper. The developed theoretical model is based on the assumed displacement function which includes the anti-symmetric mode through thickness and symmetric mode in length. The constitutive equation with flexoelectricity, governing equations and boundary conditions are derived from the Gibbs energy density function and variational principle. For the effect of flexoelectricity, we only consider the shear strain gradient in the thickness direction so as to simply the mathematical model. Thus, two flexoelectric coefficients are used in the present model. The electric potential functions are also obtained for different electric boundary conditions. The present results clearly show that the flexoelectric effect has significant effect on vibration frequencies of thickness-shear modes of thin piezoelectric crystal plate. It is also found that the flexoelectric coefficients and length to thickness ratio have influence on the thickness-shear modes. The results tell that flexoelectricity cannot be neglected for design of small size piezoelectric resonators.

Description: In this study, the hot tensile test was carried out using the extruded and annealed Mg-1Al-6Y alloy. The effect of temperature and strain rate on the hot tensile deformation behavior of the alloy was systematically studied at different temperatures (200 ℃ ~ 350 ℃) and different strain rates (8×10-5 s-1 ~ 1.6×10-3 s-1). In addition, the effect of temperature on the evolution of microstructure when the strain rate is 1.6×10-3 s-1 was investigated. The results showed that as the temperature increased or the strain rate decreased, the peak stress decreased and the elongation increased. Hot tensile at different temperatures all increased the texture intensity, and the microstructure after deformation showed obvious characteristics of basal fiber texture ([0001]⊥ED). Correspondingly, the weaker [-15-40]//ED texture before deformation transformed into a stronger [01-10]//ED fiber texture. After deformation, the average Schmid factor (SF) of each non-basal slip was significantly increased compared with the average SF before deformation, indicating that abundant non-basal slip was activated during the deformation. When the deformation temperature was 300 °C, dynamic recrystallization (DRX) occurred significantly, and the DRXed grains accounted for 15.9%. DRX was a combination of continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). Furthermore, the calculated activation energy of the alloy was about 98.8 kJ/mol. Comprehensive research showed that the hot tensile deformation mechanism mainly included intragranular slip, grain boundary slip (GBS) and DRX.

Description: This paper aims to investigate the influence of periodicity temperature change on the properties of dry granular materials in macroscopic and microscopic. A series of cyclic thermal consolidation tests have been carried out based on the discrete element method (DEM) that incorporate particles’ volumetric thermal expansion coefficient. The simulation of the direct shear test was carried out on the samples after thermal cycling. Results showed that thermally-induced volumetric strain accumulation of the specimen can be calculated by the DEM model, based on the PFC2D software. The lateral pressure degraded concomitantly thanks to decreases in particles’ horizontal contact during periodic thermal cycling. In addition, the shear dilatancy level decreases during the shearing process with the number of thermal cycles. Both the size and anisotropy of the normal contact force and contact number and the force chain are affected by the temperature cycle. Finally, the results of this paper have a certain reference for the engineering practice, such as thermal piles or others, when granular materials are subjected to thermal cycling.