ALBERT

Notes: Wavenumber aliasing is the main limitation of conventional optimum least-squares linear moveout filters: it prevents adequate reject domain weighting for efficient coherent noise rejection. A general frequency domain multichannel filter design technique based on a one-to-one mapping method between two-dimensional (2D) space and one-dimensional (1D) space is presented. The 2D desired response is mapped to the 1D frequency axis after a suitable sorting of the coefficients. A min-max or Tchebycheff approximation to the desired response is obtained in the 1D frequency domain and mapped back to the 2D frequency domain. The algorithm is suitable for multiband 2D filter design. No aliasing damage is inherent in the linear moveout filters designed using this technique because the approximation is done in the frequency-wavenumber (f, k)-domain.Linear moveout filters designed by using the present coefficient mapping technique achieve better pass domain approximations than the corresponding conventional least-squares filters. Compatible reject domain approximations can be obtained from suitable mappings of the origin coefficient of the desired (f k)-response to the 1D frequency axis. The (fk)-responses of linear moveout filters designed by using the new technique show equi-ripple behavior. Synthetic and real data applications show that the present technique is superior to the optimum least-squares filters and straight stacking in recovering and enhancing the signal events with relatively high residual statics. Their outputs also show higher resolution than those of the optimum least-squares filters.

Notes: The inversion of seismic traces allows the estimation of reservoir porosity from an analysis of transit times derived from the pseudo-velocity logs. A four-step computational procedure is illustrated consisting of (i) inversion of seismic traces and calculation of interval velocities; (ii) accurate stratigraphic interpretation; (iii) determination of the petrophysical parameters for the porosity evaluation; (iv) analysis of the reliability of the results and final corrections.Both the possibilities and the limits of the method are discussed. One of the causes of error is the fact that impedances—and not velocities—are readily obtainable from seismic data. Moreover, the porosity due to fracturation contributes only slightly to velocity, while it often contributes most importantly to the permeability.Results are shown for two of the most significant reservoir types, i.e. carbonatic and clastic. Two cases belonging to the latter type will be examined. In the first case the primary porosity is dominant. The second case is very complex and both primary and secondary porosity are present.

Notes: To investigate the effect of permeability on the propagation of seismo-acoustic waves through marine sediments, a theoretical model based on Biot's equations is established which relates the compressional wave velocity measured at a fixed frequency to computed velocities at zero and infinite frequencies in terms of sediment porosity and permeability. The model is examined experimentally in a standard soil mechanics consolidation test (itself dependent, among other things, on sediment porosity and permeability) which has been modified to include measurements of compressional wave velocity at 1 MHz and shear-wave velocity at 5 kHz. This test allows the elastic modulus of the sediment frame to be assessed under different load conditions simultaneous with the velocity determinations.From a number of tests on different samples, five samples are chosen to typify the range of sediment sizes. The results show that the difference between the measured velocity at 1 MHz and the model-derived velocity at zero frequency increases with increasing particle size (from clays to fine sand), with decreasing porosity, and with increasing permeability. For sediments coarser than fine sand the simple model breaks down, possibly because of the dominance of scattering/diffraction effects at the high frequency of the experiment. Within this limitation the model seems satisfactory to offer a capability of predicting the permeability of a sea floor sediment to an order of magnitude by the in situ measurement of seismic velocities over a wide range of frequencies; the prediction process requires a good in situ determination of sediment porosity such as that offered by electrical formation factor measurements.

Notes: A methodology is outlined for using general complex compliance functions—which contain the constant-Q case and any kind of fluid saturant as special cases—to determine the nature of that saturant from seismic reflections observed on seismic records. The important attribute of such a formulation based upon complex compliance functions is that the presence of any kind of saturant is indicated by the values of the parameters contained within the complex compliance function, the latter having the same mathematical form for all rocks under any conditions as long as it remains a crystalline solid.

Notes: Gravity measurements were made in the Mailaram copper mines, Andhra Pradesh. The observations were distributed between the two shafts situated about 220 m apart and in the three levels up to a maximum depth of 100 m. Assuming a normal free-air gradient, average densities for the three layers were determined as 2.631, 2.604, and 2.823 g cm-3, respectively. Upon incorporating the weighted mean density values from measurements on samples, the free-air gradients were found to be 0.315 mGal m-1 for the second layer (i.e. between the first and second levels) and 0.2978 mGal m-1 for the third layer (i.e. between the second and third levels). The density variation map obtained from the gravity data, the deduced anomalies, the weighted mean density values from measurements on rock samples, and the varying free-air coefficients all suggest correspondence with the concentration of ore lodes.

Notes: Common midpoint data are now being collected with ever increasing source-receiver offsets. For wide aperture seismic data classical methods of interpretation fail, since velocity analyses and signal-to-noise enhancement methods based on hyperbolic traveltime curves are no longer appropriate. Therefore, the goals of increased velocity resolution and signal enhancement, which motivate the increase in offset, are not achieved. Approximate methods, involving higher order traveltime curves or extrapolations, have been developed for velocity analysis but these are ineffective in the presence of refracted arrivals, and lack a physical basis. These problems can be minimized by transforming the observational data to the domain of intercept or vertical delay time τ and horizontal ray parameter p. In this domain headwave refractions are collapsed into points and both near vertical and wide angle reflections can be analyzed simultaneously to derive velocity-depth information, even in the presence of velocity gradients or low velocity zones.

Notes: Using the concept of reciprocity and the known solution for the electric field of a vertical oscillating magnetic dipole source placed over a two-layered halfspace, an integral expression for the vertical magnetic field produced by a horizontal rectangular loop, carrying an oscillating current and placed on the surface of the same halfspace, is deduced. This expression is such that it can be evaluated by a combination of straightforward numerical integration and digital linear filter techniques. Displacement currents everywhere in space are neglected.Fields both inside and outside the loop are presented as sounding curves. A little over a decade of frequencies (100–3000 Hz) appears to be the minimum requirement and two decades (100–10000 Hz) are sufficient for most situations. Parametric and geometric sounding curves both show good resolution of subsurface layering. Phase shows better resolution than amplitude. Similarly, resolution is higher when conductivity increases with depth than when it decreases.Besides being useful for the electromagnetic depth sounding for layered earth structures, such computations can be applied to determine normal corrections to Turam observations, whenever a rectangular loop of finite size is used as a transmitter.

Notes: The surface resistivity method has been used to study a few exposed coal seams located in the northwestern part of the Raniganj Coalfield (belonging to the Damodar Valley Gondwana basin), India. Different electrode configurations, viz., Wenner, two-electrode and half-Schlumberger, have been used with different electrode spacings in horizontal profiling. The vertical distribution of resistivity has been studied using Schlumberger configuration at different locations along the profile.Laboratory studies of resistivity (at partial to full water saturation conditions) and porosity of different coal, shaly sandstone and sandstone samples of the survey area had already been carried out before the field survey. The results indicated the presence of a good resistivity contrast between the coal seams and the surrounding formations.The field results did not bear this out: the resistivity responses of the coal formations on the profiles and sounding curves are not as clear as one would expect for such high contents. The Wenner profiles show a broad resistivity anomaly over the coal seams. Two-electrode profiles are less noisy than Wenner profiles. Sharp peaks have been observed over the coal seams. The half-Schlumberger configuration seems the best: all the coal seams and their edges can be accurately outlined on the resistivity curves.Borehole data close to the profile have been used for correlating the field results. There is good agreement with vertical electrical soundings.

Notes: Source strength of an airgun array may be increased by:〈list style="custom"〉—utilizing higher pressure,—increasing total array volume,—employing more guns,—improving gun efficiency.One measure of gun efficiency is “specific source strength”, Pa*, defined as source strength per unit quantity of air used. Typical units are MPa m/l. Most developments are directed toward increasing gun pressure and/or gun volume to increase source strength of the array. These efforts require that more air compressors be installed onboard the ship. Consequently, a larger ship may be needed for the additional compressors, guns, and auxiliary equipment.A development program was initiated in 1976 to increase source strength of the array without using a larger ship. New guns were designed and built—one for 41.4 MPa and 7.37 liter (6000 p.s.i./450 in3) operation and another with 13.8 MPa and 4.92 liter (2000 p.s.i./300 in3) capability. Experiments were conducted with these new guns (and existing guns) over a range of pressures from 13.8 to 41.4 MPa (2000 to 6000 p.s.i.).Design of the new guns was aided by a mathematical model. The model relates physical dimensions of the airgun to acoustic pressure in the water. It consists of four nonlinear differential equations relating〈list style="custom"〉—shuttle motion,—bubble pressure,—chamber pressure,—bubble radius.The last equation is the “free-bubble-oscillation equation” and represents the ideal case of a pressurized bubble released instantaneously in water. The three other equations modify this ideal case; the four equations together model an airgun of the type manufactured by Bolt Associates, Inc.

Notes: Geometrical acoustic and wave theory lead to a second-order partial differential equation that links seismic sections with different offsets. In this equation a time-shift term appears that corresponds to normal moveout; a second term, dependent on offset and time only, corrects the moveout of dipping events.The zero-offset stacked section can thus be obtained by continuing the section with maximum offset towards zero, and stacking along the way the other common-offset sections.Without the correction for dip moveout, the spatial resolution of the section is noticeably impaired, thus limiting the advantages that could be obtained with expensive migration procedures. Trade-offs exist between multiplicity of coverage, spatial resolution, and signal-to-noise; in some cases the spatial resolution on the surface can be doubled and the aliasing noise averaged out.Velocity analyses carried out on data continued to zero offset show a better resolution and improved discrimination against multiples. For instance, sea-floor multiples always appear at water velocity, so that their removal is simplified.This offset continuation can be carried out either in the time-space domain or in the time-wave number domain. The methods are applied both to synthetic and real data.

Notes: Geoelectric soundings were used to investigate the younger fault activity (Middle and Early Pleistocene) of the southwestern fault margin area of the Central Graben (and extension of the Rhine Graben) in the southern Netherlands and northern Belgium. Some effects of this fault activity can still be observed in the present geomorphology and hydrography. Investigations have been concentrated on the uppermost 20–30 m, consisting mainly of Middle and Early Pleistocene fluviatile deposits. Marshy clays and loams are most conductive. They alternate with large sand beds and gravelly gully infillings, characterized by high specific resistivities. Problems in the interpretation of the geoelectric data, caused by the variability of the deposits, are partially solved by in-situ resistivity measurements (“mini-electric” measurements). In spite of the lithologic inhomogeneity, a few marker horizons allow the geologic structure to be determined. Some new tectonic boundaries have been traced. The movements along the faults during the Quaternary are very small (less than 10 m). Therefore, the network of soundings has to be very dense and a very intensive analysis of the soundings is necessary. The results also have a hydrogeologic significance. This project illustrates the possibility of locating small tectonic structures in relatively inhomogeneous deposits by a detailed and carefully designed geoelectric survey.

Notes: This paper is directed at modeling layered media. We extend the plane-wave normal-incidence state-space model developed by Mendel, Nahi and Chan in 1979, to the non-normal incidence case. To do this we introduce a shifting principle, a zero-offset wavefront, and zero-offset travel times for different layers. We also develop an algorithm for obtaining a synthetic line source reflection seismogram. In this algorithm non-normal incidence plane-wave seismograms are summed over a range of incident angles. The algorithm is based on a modified version of Sommerfield's (1896) theorem. Simulations of acoustic and elastic media are included which illustrate the applicability of our plane-wave and line source seismograms for both elastic and acoustic cases.

Notes: The principles for ray-tracing and wavefront curvature calculations in a three-dimensional medium are reviewed. A new derivation of the transformation of the wavefront curvature matrix at an interface between two inhomogeneous media is given. The derivation is based on a Taylor series expansion of the ray refraction equation at the interface between two inhomogeneous media, and only elementary geometric arguments are used. The wave-front curvature transformation at the interface is obtained by neglecting all terms in the direction of the surface normal.With proper definition of the variables, the derivation is also valid for a reflected wave-front. A simplified transformation rule is derived for a reflected wave of the same type as the incident wave.

Notes: A brief history of the development of the inverse problem in resistivity sounding is presented with the development of the equations governing the least-squares inverse. Five algorithms for finding the minimum of the least-square problem are described and their speed of convergence is compared on data from two planar earth models. Of the five algorithms studied, the ridge-regression algorithm required the fewest numbers of forward problem evaluations to reach a desired minimum.Solution space statistics, including (1) parameter-standard errors, (2) parameter correlation coefficients, (3) model parameter eigenvectors, and (4) data eigenvectors are discussed. The type of weighting applied to the data affects these statistical parameters. Weighting the data by taking log10 of the observed and calculated values is comparable to weighting by the inverse of a constant data error. The most reliable parameter standard errors are obtained by weighting by the inverse of observed data errors. All other solution statistics, such as dataparameter eigenvector pairs, have more physical significance when inverse data error weighting is used.

Notes: An analytical relationship for the autocorrelation function of an upsweep with high-frequency attenuation is used in the construction of synthetic seismograms.Field experiments were conducted in two areas to investigate the attenuation of upsweep where the near-surface materials were different. The results showed that the attenuation of high frequencies occurs at the source point depending on the near-surface lithology.The attenuation effect is usually neglected in the construction of the input wavelet of synthetic seismograms for Vibroseis data. In this study, the high-frequency attenuation of upsweep was considered in the construction of the input wavelet for the synthetic seismogram in an area where the Vibroseis technique was used. The synthetic seismogram generated in this manner had a better correlation with the Vibroseis section than that of corresponding synthetics using minimum-phase and the unattenuated autocorrelation wavelet of the upsweep.

Notes: The frequency domain response of a grounded linear circuit is deduced. The model of the ground is a homogeneous conducting half-space whose horizontal and vertical conductivities are specified. The source itself is formulated as an insulated current-carrying wire of finite length lying on the surface that is grounded at its end points. The tangential electric field expressions are used to calculate the induced voltage between two additional electrodes that are connected by an insulated wire. Particular attention is paid to the transient coupling response in the potential circuit when the source current is a step-function of time. Among other things, it is shown that the voltage response is a step-function only if the circuits are at right-angles and if the ground is effectively isotropic and nonpolarizable.

Notes: Application of dip-moveout attempts to correct pre-stack data in such a way that they stack correctly, however far the reflector geometry departs from an ideal plane horizontal interface. Even for plane dipping reflectors under a constant velocity overburden a common mid-point gather contains reflections distributed over a finite segment of the reflector. It is shown that under these conditions application of dip-moveout moves dipping energy on common offset gathers in such a manner that common mid-point gathers become true common depth point gathers.

Notes: Two methods for estimating the true formation temperature from well logs are compared. One method requires knowledge of the circulation time, whereas the other requires an estimate of the thermal diffusivity of the contents of the well. Both methods require three or more successive bottom-hole temperature measurements. Data from 157 wells have been analyzed, and the calculated formation temperatures from the two methods agree well. By an analysis of best matching of the two methods, it is found that 0.35 × 10-6 m2 s-1 is a good estimate for the thermal diffusivity of the well contents.

Notes: A new presentation for magnetotelluric data is proposed to be used together with the traditional representation. It is easily computed by applying the Bostick transform to all field data points. The result is an approximate depth-resistivity diagram which contains an indication of the data quality as well as the homogeneity of the subsurface. This resistivity section should be used in the interpretation of surveys in which accuracy is either not of prime concern or cannot be achieved. Since this mode of presentation is easily understood it can be used to familiarize earth scientists with the use of the MT method in exploration.

Notes: Varieties of Italian, perennial and Italian × perennial ryegrasses, tall fescue and cocksfoot were used to determine the effects of soil moisture on grass growth. Weather conditions were monitored and herbage accumulation, leaf extension rate, leaf appearance rate and tillering were recorded under natural (control), covered and irrigated treatments.Water deficit reduced crop growth rate in the spring and drought was the major factor influencing crop growth rates in all varieties during the summer. The ryegrasses appeared most sensitive to drought, and particularly poor recovery growth was exhibited by the Italian ryegrass RvP and the hybrid ryegrass Snowdon.Leaf extension rate and leaf appearance rate were both reduced by increasing soil water deficit. Herbage accumulation was increased by irrigation when potential soil water deficits were greater than 100 mm. When water deficits were large, irrigation increased leaf extension more than leaf appearance or tiller number. Increasing moisture deficit had a greater effect upon tiller number than on leaf extension.

Notes: Records of grassland productivity were kept for 2 years on 152 dairy and 179 beef farms. Results were collated for six lowland zones, delineated primarily on the basis of average rainfall, and an upland zone. Contemporary and long-term average meteorological records were also collected.In most of the lowland zones stocking rates and use of fertilizer N were similar, but utilized metabolizable energy (UME) output from grass varied; it was 25% higher in the wet, cool zone of north-west England and east Wales than in the dry zone of eastern England. The ranking of zones for utilized output corresponded closely with the ranking for summer rainfall.On upland farms stocking rate was 25% lower and UME output 15% lower than on lowland farms, but this was achieved from little more than half the N input.The differences between zones were similar to those shown in other published farm data. They also showed a similar trend to that demonstrated in grass cutting experiments. This suggests that farmers were, on average, able to exploit the extra grass grown in wetter climates. The incidence of difficult topography and impeded drainage was similar in dry and wet zones, but did have a more serious effect in the wet zones. The much higher level of concentrate feeding in the driest zone may have reduced the utilization of grass.

Notes: Twelve varieties of cocksfoot, Dactylis glomerata L., were analysed for three mineral elements (Na, K, Ca) and their dry matter (DM) yields were measured in pot and field trials. Among these characteristics there were strong varietal differences in Na concentration, whereas in other cases the varietal differences were less significant. The concentrations of individual mineral elements were, in most cases, independent of yield and of one another.Parent plants and their clonal derivatives were highly correlated in Na and Ca concentration as well as in DM yield. Tiller size or position on the parental plant had no significant effects on the mineral concentrations or DM yields of clones derived from separated tillers.Within varieties continuous variation was observed for Na concentration and the range of variation increased with increasing mean Na concentration. When plants were grown under different experimental conditions there was a high repeatability in Na concentration within varieties over cuts and years. This result was taken as an indication of a strong genetic basis for Na concentration. The results obtained in this study show that it is possible to develop grass varieties of defined potential Na concentration.

Notes: Samples of 39 perennial ryegrass (Lolium perenne L.) and 24 Italian ryegrass (Lolium multiflorum Lam.) commercial seed-lots used at the Grassland Research Institute between 1974 and 1978 were examined for the presence of seed-borne Drechslera species. The five species of Drechslera isolated from the seeds were D. andersenii, D. siccans, D. nobleae, D. sorokiniana and an unidentified Drechslera sp.A high proportion of the seed-lots were infected but levels of infection were low except in the perennial ryegrass cv. S24. Infection was located more commonly inside the caryopses than externally on the lemmas and paleae, and about 12% of the seedlings growing from infected seeds were infected. The species recovered in the seedlings were the same as those observed on the seeds.There was no relationship between level of seed infection and level of damage observed in the field in the autumn of the first harvest year.

Notes: A high risk of pest damage to seedlings of white clover (Trifolium repens L.) and perennial ryegrass (Lolium perenne L.) was shown to exist after reseeding with a slot-seeder. Damage varied between years and sites; white clover appeared to be more affected than perennial ryegrass. Insecticides of feasible commercial use (chlorpyrifos granules and γ-HCH seed treatment) were found to prevent damage. There was no evidence of phytotoxicity from any of the pesticides studied at the dose rates used in the field.

Notes: Seismic dynamic deconvolution is the mathematical basis on which a degree of unification in different prospecting methods is possible, relative to the parameter identification in horizontally stratified media. There is a basic structure which has some immediate applications to the inversion of resistivity data and possibly to other problems. For resistivity soundings there exists a key equation which is parallel to the energy conservation law in the theory of synthetic seismograms.

Notes: Magnetotelluric response is studied for an inhomogeneous medium having conductivity varying linearly with depth as σ(z) =σ1+αz. For a medium having conductivity increasing linearly with depth, the phase of the impedance approaches 60° at long periods and the apparent resistivity becomes log (ρa) = 2 log (1.36/α1/3) — 1/3 log (T'). The asymptote of log (ρa, T'→∞) when plotted against log (T') has a constant gradient —1/3 and has an intercept on the log (T') axis, which equals 6 log (1.36/α1/3). When a homogeneous layer with a moderate thickness overlies an inhomogeneous half-space, this layer does not affect the asymptote, but it affects the cut-off period and pushes this toward the long period direction. For a medium having conductivity decreasing linearly with depth, the impedance is equivalent to that of a Cagniard two-layer model; the intercept period related to the thickness is T'0=σ1(h2/2)2. Homogeneous multilayer approximations to an inhomogeneous layer are also investigated, and it is shown that the fit to the model variation depends on the number of layers and the layer parameters chosen.

Notes: Modern seismic processing techniques developed in recent years have provided the explorationist with more meaningful data than would have been predicted even by optimists. Correct migration of seismic data, relative amplitude preservation of reflections, and seismic trace inversion represent the necessary efforts to ensure that the best possible picture of in situ physical properties of the subsurface section is revealed. Moreover, compacted and over-pressured zones can be predicted from surface data prior to drilling a well through them.The basic tool for predicting overpressured zones from the surface is still the velocity analysis derived from good reflection data with few erratic multiples. The extraction of regional normal compaction trends from the seismic velocities allows one—where velocities deviate from the trend—to locate the top of overpressure. Moreover, the statistical behavior of the ratios of the sonic log vs pore pressure in existing boreholes enables one to convert the deviation from the trend of the seismic velocities into overpressure rates expected at the seismic reflection horizon.This paper presents a field case study showing how the knowledge of well site lithology together with the more detailed information extracted from inverted seismic data enables the prediction to match well conditions with high reliability.

Notes: Complete analytical expressions are developed for the first and second derivatives of the Newtonian gravitational potential in arbitrary directions due to the homogeneous revolutional compartment with a polygonal vertical section by applying the Gaussian divergence theorem in the cylindrical coordinate system. Elementary solutions presented can easily be translated into magnetic anomalies caused by a uniformly magnetized body.The divergence approach in the polar coordinate system is also described, and gravity attractions in the radial direction are presented in closed form associated with a homogeneous cap compartment. The explicit solutions are tested against well-known formulae for a cylinder, cone, infinite plate, and sphere.

Notes: The notion of nonvertical incidence plane wave seismograms and nonzero effect point source seismograms are sometimes confused with each other in the literature. This short note attempts to clarify this confusion which is observed in Douze (1979).

Notes: In the Gulf of Cadiz, a Tertiary basin became filled by clastic series during Miocene and Pliocene times. This terrigenous influx, derived from the Iberic Meseta in the north, is characterized by a sandy episode during the Tortonian and Messinian. The sand deposits were probably connected with uplift and major erosion of the Meseta during the sliding of the olistostrome, which occupied the south of the basin from late Helvetian to middle Tortonian.High resolution seismic techniques produced a good picture of the stratigraphy and of the depositional environment of the sands.A further study, using the amplitude of the reflections, inversion of seismic traces into acoustic impedance traces, and modeling, provides a remarkable example of the possibilities of seismic stratigraphy for depicting the lateral evolution of facies and localizing hydrocarbon occurrences. Out of seven exploratory wells based upon seismic information, six encountered gas-bearing sands with economic potential.

Notes: Problems of the resistivity sounding method may be reparametrized by means of Dar Zarrouk—or generalized D.Z.—transformations.A complete set of equivalent models is subdivided into three classes: initial models, intermediate models, and all other models. Equivalent reparametrized models are subdivided into three analogous classes. There is no one-to-one mapping of intermediate primary and intermediate reparametrized models. Non-trivial equivalent models are generated from initial models via intermediate reparametrized models. A method is developed to find equivalent models relative to the uncertainty of resistivity soundings.There are different forms of approximate equivalence laws, apart from those commonly accepted. The equivalence depends considerably on the “flatness” of the sounding curve. For mean flatness, the electric models exhibit the (hp±2)-equivalence rather than the (hp±1)-equivalence.

Notes: AEM (airborne electromagnetic) anomalies caused by massive sulphide conductors and superficial conductors can be recognized with a statistical method, as shown by an analysis of Input AEM data from Karnataka State. The weathering in the survey area is of tropical type. Parameters, such as various amplitude ratios and time parameters (inverse of decay rate) for exponential and power-law decay were analyzed for sulphide bodies, conducting soil, superficial conductors, and cultural conductors. Time parameters τ1 (exponential decay) is defined as ratio of time differences between the third and fourth channel to the logarithmic value of the relative amplitude of the two channels. Time parameter K1 (power-law decay) is defined as ratio of the difference of the logarithmic values of the delay times of the third and fourth channels to the logarithmic value of the relative amplitude of the two channels. The two parameters have been useful in recognizing sulphide conductors. Also the first channel Input amplitude and logarithmic plot of the transients appear to be helpful in conductor identification. Channel ratios seem to be the least effective parameters of conductor identification. In the area studied both power-law and the conventional exponential decay were found equally suitable for approximating Input AEM transients.

Notes: A seismic source consisting of a 700 kg weight that could be dropped vertically or projected down a ramp inclined at 45° to the vertical was tested as a source of P, SV and SH waves within a crystalline rock body at Chalk River, Ontario. The seismic energy was recorded by arrays of both horizontal and vertical-component geophones at distances between 30 and 600 m from the source, which was operated over glacial overburden varying in thickness from less than a meter to a few tens of meters. Seismic energy was more efficiently generated when the overburden thickness was at least several meters. The signals identified visually as S are generally true S, though some may be the converted wave PS. The SV amplitudes are generally larger than those of P, regardless of the type of shot, while the signal frequencies are roughly 60 Hz and 90 Hz, respectively. The horizontal-component seismograms for the inclined shots showed no evidence of SH polarization, and the SH amplitudes were only rarely enhanced relative to P and SV amplitudes on changing from vertical to inclined shots. These unexpected results are attributed to the combined effect of the high velocity and density contrasts and the irregularity of the boundary between the glacial overburden and the rock body.

Notes: The statistical properties and applicability of the Dry-Weight-Rank (DWR) method of pasture sampling are examined. Formulae for the expected value and variance of the DWR estimates are presented.The extent of bias in DWR is examined using several mathematical models. DWR is shown to break down when estimating multinomial proportions; however it provides good estimates for a subset of models simulated from a class of compound probability distributions.The success of DWR in practice does not rest on a theoretical basis. It appears to be a remarkable empirical discovery that DWR estimates are virtually unbiased on most pasture types. Several cases are considered where difficulties may be encountered in using DWR. Provided the theoretical reservations of this paper are borne in mind, DWR will continue to be a useful practical tool, especially in the absence of non-destructive observational alternatives.

Notes: Three groups of cows were continuously stocked on pasture and offered supplementary concentrates according to the herbage height measured weekly with a grass disc. Concentrates were offered when the mean herbage height fell below 9 cm for treatment A, 7 cm for treatment B and 5 cm for treatment C at a rate of 1 kg d-1 for each 0·2-cm decline below these threshold levels. If the herbage height declined by more than 1·2 cm (8 kg concentrates d-1) hay was offered in addition ad libitum. The stocking rates for all three treatments were 5·2, 3·2 and 3·2 cows ha-1 for three successive 8-week periods. For treatments A, B and C the mean concentrate DM intakes were 3·2, 1·2 and 1·2 kg d-1 (treatment A also received 0·2 kg hay DM d-1), and the mean daily milk yields were 17·2, 16·2 and 15·2 kg respectively. The increasing level of supplementary feeding from treatment C to A also resulted in an increase in liveweight and body condition score change, and a reduction in milk fat.

Notes: The effects of sheep grazing on the development of and production from heather swards and on intake and diet selection by grazing Scottish Blackface wether sheep were studied in an experiment in which sheep numbers were adjusted to remove 0, 40% or 80% by weight of current season's shoots in summer and in autumn for a period of 5 years. All combinations of season and level of grazing were provided. The plots were divided after 2 years and grazing was continued for a further 3 years on one subplot but discontinued on the other.Sward productivity during the 5 years of grazing was unaffected at the 40% level of shoot removal but at the 80% level was reduced by up to 66%.After a season's uninterrupted growth at the end of the experiment heather cover and herbage mass were lower and current season's shoots as a proportion of total mass were higher on those treatments which received the greatest severity of grazing. Weight of current season's shoots was unaffected on treatments which had received the 40% level of shoot removal but was reduced by 40% and 50% on treatments which had received the 80% level in summer and autumn respectively. On the rested subplots sward recovery was such that no treatment effects remained after 3 years except with respect to 80% shoot removal in autumn where herbage mass was reduced compared with other treatments.Intakes of digestible organic matter per sheep were higher at the 80% than the 40% level of grazing in the fifth year of the experiment. This was ascribed to the ingestion of new shoot growth from the twig bases on the 80% level of removal treatments. Intake and digestibility were higher in the summer on those treatments which had received the 80% level of removal in previous autumns. Over the 5 years of the experiment there was a small decline in intake and digestibility values, with the decline being greatest in the summer and at low levels of grazing.Floristic changes differed on the rested and grazed areas. On the rested subplots in the fourth year after grazing stopped, heather height was lower and cover by grasses, sedges and herbs was greater on treatments which previously had received the highest levels of utilization. On bare areas the rate of recovery of heather was rapid where shoots as well as seedlings contributed to recovery growth. On the grazed subplots, with the exception of the low-growing ruderal Rumex acetosella, cover due to grasses, sedges and herbs remained low as species other than heather were selectively grazed.Relationships among stocking rates, grazing behaviour and heather utilization are discussed and guidelines for the recognition of overgrazing are outlined.

Notes: In a study of growth rates and developmental morphology of simulated swards of two contrasting white clover varieties, Katrina and Kent, it was found that both varieties continued to produce dry matter throughout the winter at Aberystwyth. The gross crop growth rate in the coldest periods was about 7 kg ha-1 d-1. The rates of formation and loss of new leaves were approximately equal so that there was no net increase in weight until the latter part of March. This initial net weight increase in both varieties was observed in the same harvest interval, the most important factor being the difference in weight between the new leaf plus petiole unit and the weight of the unit which it replaced. The weight of laminae and petioles throughout the experiment was somewhat higher in Katrina which has come to be regarded as the ‘earlier’ variety.The prospects for improving spring production in white clover by variety improvement are discussed.

Notes: A technique for estimating the rate of disappearance of material from samples of dead herbage protected by simple nylon or wire mesh covers is described. Using this technique on a perennial ryegrass sward in southern England during August-November, relative rates of disappearance close to 0·204 g g-1 d-1 (DM) were obtained, but the variability was high. When herbage killed with paraquat was used, the rate of disappearance was higher and the variability lower. There were only small differences in the temperatures recorded in a normal sward and within samples of dead herbage under mesh covers.

Notes: Electrical capacitance and root diameter techniques for estimating root dry weight were evaluated in one test with red clover plants grown on slant-boards in plant growth chambers for 37–77 d, and in six tests with alfalfa grown in the field for 55–165 d. Root dry weights of red clover were estimated satisfactorily with regression equations from both diameter (R2=90%) and capacitance (R2=76%) measurements. Root dry weights of alfalfa were estimated satisfactorily throughout the entire season from diameter values (R2 from 51 to 92%). Alfalfa root weight was significantly (P 〈0·25) related to capacitance values at the beginning and at the end of the season but not at mid-season. Electrical capacitance measurements were similar for intact root systems and roots severed 4 cm below the crown in separate experiments with red clover and with alfalfa. The root diameter technique provided an accurate, rapid and inexpensive method of estimating root size throughout the first season of growth. The root capacitance method provided satisfactory estimates of roots at certain times during the summer. Neither method would be useful if a large portion of the root was naturally severed.

Notes: Italian ryegrass was slot-seeded into permanent grass in two field experiments at Oxford. In the first experiment August and September proved to be the most reliable months for slot-seeding, with April as a possible alternative. A row-spacing experiment showed that the optimum distance between rows was about 30 cm; seed rate in the row had a lesser influence on increasing herbage growth. In both experiments slot-seeding did not result in any substantial change in earliness of growth or alter total herbage harvested but it did even out the seasonal distribution of growth, particularly by increasing it in the following July.

Notes: An apparatus is described which enables excised pieces of plant material lo be weighed al frequent intervals as they dry in controlled conditions of temperature, humidity and air-speed. The effect of removing the epidermis on the drying rate of red clover (Trifolium pratense) leaflets, leaf petioles and stems is examined. Initially this treatment caused a very large increase in the drying rate of leaflets. Although the effect declined as water content fell, leaflets from which the epidermis had been removed still dried more rapidly than the controls at a water content equivalent to 50% of the dry weight. Removing the epidermis had a greater effect on the drying rate of leaf petioles and stems at low water contents than it did on the drying rate of leaflets.Slow drying at low water contents is a major factor responsible for the undesirably long periods for which hay may lie in the field. Slow drying occurs even though swath microclimate becomes more favourable for drying as water content falls. The results presented here suggest that treatments which reduce cuticular resistance have the potential to reduce field drying time.

Notes: A detailed study of the spring growth curves of two forage grasses, tall fescue and cocksfoot, over three successive years showed a large variability of growth over the vegetative phase. This variability was evident at levels of fertilizer N which were considered to be non-limiting (60 kg N ha-1 in autumn plus 120 kg N ha-1 in February).At this level of N there was a relationship between yield in the vegetative phase and accumulated temperatures from the last cut in the autumn which was described by a regression common to the three years. The slope of this regression represents the potential growth of a variety. At a lower level of N a separate regression was needed in each year to relate growth to accumulated temperature.Variation in spring growth was not related to accumulated net radiation. Growth in the reproductive phase was related to accumulated temperature and accumulated net radiation from the 10-cm ear stage.

Notes: In subtropical latitudes temperate crops can be grown during the cool months but the growing season is restricted by the termination and beginning of hot weather. Postponing sowing date in south Florida from October to November to January resulted in 150, 130 and 110-d growing seasons respectively. Dry matter (DM) yields of turnip, swede, rape and kale were lowered by each later sowing date and shorter growing season, and crude protein (CP) concentration was the same as for, or was increased by late sowing. In vitro organic matter digestibility (IVOMD) of turnip, swede and rape leaves was not affected by sowing date, but roots of turnip and swede from the earlier sowings and longer growing seasons were more digestible. Yield of the four species depended on harvest management as well as date of sowing and length of growing season. Total yield of turnip and swede were unaffected by harvest management but multiple cutting resulted in greater leaf yields and smaller root yields, whereas stockpiling resulted in smaller leaf yields and larger root yields. Kale produced more DM when harvested once at the end of the winter growing season but rape produced the greatest DM yield when sown in October and harvested

Notes: Plants of white clover (Trifolium repens L.) cv. Blanca and red clover (T. pratense L.) cv. Hungaropoly were grown singly in controlled environments. The effects of eight treatments on the two species were examined: 16- and 8-h photo-periods × 20/15 and 15/10°C day/night temperatures ×Rhizobium-free plants receiving nitrate N and inoculated plants receiving no combined N. Twice weekly measurements of the main axis leaf size, petiole length, rate of leaf production and the time period between the appearance of a leaf and its final size were carried out for 8 weeks after sowing.Increasing the day/night temperature from 15/10 to 20/15°C, or doubling the daylength from 8 to 16 h (doubling the daylength increased temperature by 1·2°C) accelerated the rate of leaf production and expansion and increased petiole length and the final area of leaves. Most aspects of main axis leaf growth were reduced in the inoculated plants dependent on their own N fixation compared with the nodule-free plants receiving abundant nitrate N. The results suggest that the temperature above which white clover exhibits appreciable leaf growth in the field could be relatively high compared with grasses. Further research is required to define these differences and relate them to seasonal changes in the environment.

Notes: Preharvest application of 1 and 2 litres ha-1 IPA glyphosate (glyphosate) to a seed crop of S24 perennial ryegrass with moisture concentrations of around 400 and 340 g kg-1 (40 and 34% moisture content w/w) failed to significantly lower seed and straw moisture concentration at harvest and consequently did not affect combine rate. Addition of extra surfactants and ammonium sulphate to glyphosate did not significantly increase the rate of desiccation.The quality of harvested seed was impaired at both rates and application times. Germination was significantly lowered through the production of abnormal seedlings. The germination of seed harvested in the previous year from glyphosatetreated plots decreased with storage. Seed vigour, germination rate and field emergence were also significantly decreased as a result of glyphosate application. The effect of glyphosate on seed quality precludes its preharvest use as a desiccant in the ryegrass seed crop.Harvesting difficulties due to the production of secondary vegetative tillers may be overcome by swathing rather than direct combining.

Notes: The fertility of forty-two heifers offered either red clover silage or grass silage prior to and during the period of insemination was compared. Pregnancy rate to first service was significantly higher (P 〈 0·25) on red clover silage at 76% compared with 43% on grass silage. Pregnancy rates from a mating period covering three oestrus cycles were similar on the two silage diets. The ratio of services to pregnancies was lower on red clover silage (1·2) than on grass silage (2·2). In a subsidiary trial with twenty-three heifers, pregnancy rate to first service on red clover silage was 78%.There was no evidence to indicate that herd fertility is depressed by red clover silage.

Notes: An estimate of the level of pest damage on enclosed upland permanent pasture in England and Wales was made by reducing invertebrate populations with insecticides at thirteen well-distributed sites and measuring the effect on herbage growth over a 3-year period. Potential pests were fewer in number than on lowland pastures and there was a wide range in herbage yield between sites. Insecticide treatment significantly increased annual yields at only three of the sites, and significantly decreased yield at two of the sites. Insect damage to grassland appears to be much less important in upland than in lowland areas: this may be due to the relative scarcity of frit-fly in these areas, but this could change if its preferred host, ryegrass, were encouraged by intensification of sward management in the uplands. At all but one of the sites insecticide treatment led to considerable soil compaction, probably as a consequence of suppressing earthworm populations.

Notes: Eight samples of perennial ryegrass-white clover herbage with in vivo dry matter digestibility (DMD) ranging from 0·279 to 0·264 were used to evaluate various cost-saving modifications to the two-stage pepsin–cellulase digestibility technique. The effect of sample size, cellulase quality, cellulase/sample ratio, digestion time and washing of residue following digestion were investigated. The loss of dry matter (DM) in the assay was correlated with in vivo DMD and each variation of the method was evaluated by comparing the s.d. between replicates and r.s.d. of the regression, as well as the convenience of the method for large-scale monitoring of digestibility of mixed ryegrass-clover herbage.It was found that the amount of cellulase used could be reduced by a factor of 25, compared with recently published methods, without increasing s.d. or r.s.d. appreciably. In addition stirring during digestion and washing of the residue could be omitted without any deleterious effects. Increasing digestion time did not reduce s.d. or r.s.d. and the low-grade cellulase proved to be slightly more economical.Increasing the sample size from 0·25 to 0·20 g improved the s.d. and r.s.d. but the residues from the larger samples were generally slower to filter, which made the assay unsuitable for routine use. Substantial reduction of digestion volume and use of a thermostatically controlled water bath instead of an incubator led to a considerable increase in efficiency and throughput of samples. Stirring the samples during digestion was found to be unnecessary, thus allowing more flexibility in the laboratory routine, for example using the weekend for digestion. Using the recommended method modification the repeatability between replicates and r.s.d. of the calibration regression was 0·204 and 0·215 respectively for samples ranging in DMD from 0·279 to 0·264.

Notes: Six varieties of white clover, each grown with perennial ryegrass, four intervals between cuts and two levels of applied nitrogen in all combinations, were compared in a field experiment during the first 27 months after sowing.Increasing the interval between harvests from 3 or 4 to 8–12 weeks increased the yield of white clover and generally did not reduce the proportion of clover in total herbage. Increasing the interval between harvests reduced the number of grass tillers but increased grass yield and the size of grass leaves and increased grass height more than clover height; it also increased the proportion of petiole relative to leaflet in the clover. Differences between varieties in response to interval between harvests were small but supported the view that medium large-leaved varieties can with advantage be defoliated rather less frequently than small-leaved ones. The adverse effect of applied N on clover appeared almost equally great with all four intervals between harvests and further research on this topic is suggested. Applied N increased grass height more than clover height and increased the number of grass tillers, the size of grass leaves and grass yield. The medium large-leaved varieties seemed more tolerant of applied N than the smaller varieties.

Notes: The author discusses the prospects for trade union growth in this industry in the light of a case study of the development of a branch of the Transport and General Workers’ Union within the EMI-owned Angus Steak House chain.

Notes: A number of variations in working arrangements have emerged in Australia in recent years; one of these has been job-sharing. Here the author reports the results of a survey into the attitudes of trade unions in Australia towards the practice.

Notes: In this article the author reports the findings of research over a two year period into the role of ACAS conciliators in cases in which industrial tribunals decided in favour of applicants.

Notes: Book reviews in this article: WAGES POLICY IN THE BRITISH COALMINING INDUSTRY J. L. Handy THE MILITANCY OF BRITISH MINERS V. L. Allen BATTERED CHERUB Joe Gormley KING COAL Tony Hall THE DEGRADATION OF WORK?: SKILL, DESKILLING AND THE LABOUR PROCESS Edited by Stephen Wood SOVIET TRADE UNIONS: THEIR DEVELOPMENT IN THE 1970s Blair A. Ruble BLUE COLLAR WORKERS IN EASTERN EUROPE Jan F. Triska and Charles Gati (eds.) George Allen and Unwin

Notes: Book reviews in this article: EXPLORING PARTICIPATION Paul Bate and lain Mangham WORKERS' PARTICIPATION IN DECISIONS WITHIN UNDERTAKINGS International Labour Office WORK PATTERNS Derek L. Bosworth and Peter J. Dawkins POWER AND POLITICS IN ORGANIZATIONS Samuel B. Bacharach and Edward J. Lawler DEMAIN, QUELS SYNDICATS?H. Landier CFDT LE RÉVE ET LA VIE J. C. Poulain

Notes: It has been argued recently that collective bargaining reform will contribute towards a successful incomes policy. The author in this note suggests that it is too soon to predict the demise of decentralised bargaining and the emergence of co-ordinated private sector bargaining with favourable outcomes for incomes policy.

Notes: The footwear industry is unique in its continuous use of joint local conciliation and arbitration boards to handle changes brought about by new technology and the contraction of its labour force. This case study draws on the experience of one board and assesses the wider lessons of an industry-wide arbitration system.

Notes: THE CHANGING CONTOURS OF BRITISH INDUSTRIAL RELATIONSNuffield College, OxfordWORK AND PEOPLE: AN ECONOMIC EVALUATION OF JOB ENRICHMENTLodon School of EconomicsTHE HIDDEN MEANING OF PAY CONFLICTUniversity of EdinburghCOMPETITION AND CONTROL AT WORKCentre for Research in Industrial Democracy and Participation Glasgow University

Notes: The national engineering strike of 1979 was by far the largest strike in Britain in recent years. Here the authors examine a crucial aspect of the strike which has been given little systematic attention, that is in the way it was organised at local level and mobilised mass support.

Notes: This article concentrates upon some of the practical difficulties surrounding postal ballots—level of membership involvement, the problems of contacting paid up members, the drafting of questions on ballot papers and—possibly the most important issue—the degree to which the results moderate outcomes.

Notes: This article, in exploring the processes by which employers’ generalised demand for labour is translated into actual recruitment, highlights the role of management decision-making in this important, but relatively neglected area.

Notes: Here the authors compare and contrast the findings of Peterson and Tracy's US study on differences between union and management negotiators with findings from a significant New Zealand replication of their work.

Notes: There is growing recognition in Britain that high levels of unemployment are likely to survive the current recession and economic policies. This explains the continuing interest in the work-sharing issue within British unions; this article examines some of the industrial relations issues and implications of the practice.

Notes: The impact of external regulation - such as taxation, wage and other regulations and employment legislation - on small businesses has recently attracted a good deal of academic and policy-making interest. Here the author presents the responses of some small businessmen, in retailing, to external regulation.

Notes: In this research note the author sets out and tests a model of the relationships between consumer price inflation, unemployment and strike incidence in twenty OECD countries.

Notes: There has been recent considerable interest in Britain and other countries in the practice of holding two paid jobs. This article provides the first comparative analysis of the nature and extent of ‘moonlighting’ in Britain and the USA.

Notes: The shop steward, as the most direct representative of employees at the workplace, fulfils an important, often complex and changing function within the firm. This article, using a particular shop stewards' course as a case study, assesses the shop stewards' training needs and suggests some possible reforms.

Notes: In this article, which is a version of a much larger report, the authors assess how the major trade unions, at conference and executive committee level, are responding in their policies and attitudes to the new technology.

Notes: While it is accepted that social psychology has much to offer in the understanding of industrial relations problems and the development of negotiating skills, is there any hard social psychological evidence as to the usefulness of particular techniques of negotiation? In this article the author attempts to answer this question.

Notes: This article looks at de facto and de jure participation in decision-making, as well as the degree of direct as opposed to indirect influence wielded by the parties involved. It asks whether the perceptions of those on ‘different sides’ of the industrial fence, such as shop stewards and managers, largely differ and on what issues.

Notes: The British Government's recent white paper has focused on the debate on the quality of training. Here the author's main argument is that since most existing jobs, and therefore the training associated with them, are limited in scope and interest, the key to improving the quality of training lies in an approach which stresses the redesign of work itself.

Notes: Corporate social responsibilities: the dynamics of response to the social environment

Notes: This article reports some of the results of a new and large survey which focuses on women and work. In relation to part-time work the survey confirms that the traditional factors explaining the demand for such work continue to be important but that current trends in the economy are not favourable to female employees seeking part-time work.

Notes: As a major area of employment for women, the banking industry provides considerable scope as a case study of equal opportunities in employment. This article aims firstly to analyse the extent and the various aspects of inequality in the English clearing banks and, secondly, to examine the extent of women's participation and influence within the major TUC-affiliated trade union in this field—BIFU.

Notes: Research has continually emphasised the lack of interest of management and trade unions into greater disclosure of information in collective bargaining. In this article the author explains this failure in terms of the stratification of new and existing information along hierarchical lines which do not disturb existing property rights and maintain status structures.

Notes: Here the author outlines different theories of strike patterns and examines them against several aspects of the British strike experience from 1960 to 1979. He also examines the impact of the recession on the level of strike activity.

Notes: In this article the author gives a general overview of the study of management in industrial relations and examines the assumptions underlying the increased attention being given to management by industrial relations specialists.

Notes: Book Reviewed in This Article: MULTINATIONAL COLLECTIVE BARGAINING ATTEMPTS H. R. Northrup, R. L. Rowan EMPLOYEE POTENTIAL, ISSUES IN THE DEVELOPMENT OF WOMEN WHITE-COLLAR PROLETARIAT: THE INDUSTRIAL BEHAVIOUR OF BRITISH CIVIL SERVANTS Michael P. Kelly ECONOMICS OF WAGES AND LABOUR L. C. Hunter C. Murray WORKERS' CO-OPERATIVES: JOBS AND DREAMS Jenny Thornley