ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

X
feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • AERODYNAMICS  (737)
  • SPACE VEHICLES  (597)
  • 1980-1984  (485)
  • 1970-1974  (849)
  • 1925-1929
  • 1984  (485)
  • 1972  (849)
Collection
Keywords
Years
  • 1980-1984  (485)
  • 1970-1974  (849)
  • 1925-1929
Year
  • 1
    facet.materialart.
    Unknown
    Composite systems utilization for space shuttle structures (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Research and development of composite material systems to show applicability of these materials to shuttle structures and to demonstrate availability through a hardware development program is reported. The various configurations studied and potential areas of composite structures use are described and an outline of ongoing composite programs, complementing the indicated feasible applications, including a typical cost study, is shown. The following composite systems are investigated: Boron filaments with epoxy, polyimide, or aluminum matrix, and graphite filaments with epoxy or polyimide matrix.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 605-644
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 2
    facet.materialart.
    Unknown
    Flight loads and control (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The prediction of flight loads and their potential reduction, using various control logics for the space shuttle vehicles, is very complex. Some factors, not found on previous launch vehicles, that increase the complexity are large lifting surfaces, unsymmetrical structure, unsymmetrical aerodynamics, trajectory control system coupling, and large aeroelastic effects. Discussed are these load producing factors and load reducing techniques. Identification of potential technology areas is included.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 175-203
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 3
    facet.materialart.
    Unknown
    New considerations for pogo prevention on space shuttle (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Recommendations for improving the methodology of pogo suppression for the space shuttle include: Consideration of inter-pump location for accumulator or active device, inclusion of tank outflow effects in dynamic structural analysis, the use of simplified transfer functions in systems studies, three phase dynamic testing program for turbopump with development of dynamic flowmeters, and the use of a linearized mathematical model for engine physics studies.
    Keywords: SPACE VEHICLES
    Type: NASA, Washington NASA Space Shuttle Technol. Conf.; p 97-116
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 4
    facet.materialart.
    Unknown
    Development of methods for fracture control of space shuttle structures (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The technology with respect to fracture control requirements of the shuttle is considered. The current state-of-the-art does permit an approach based on linear elastic fracture mechanics concepts. Development and implementation of a fracture control plan should recognize deficiencies and provide adequate resources for the extensive empirical test data which are required. With respect to the cost impact of such tests, recent experiences involving advanced aircraft systems have seen unit cost increases of from 200 to 500 percent.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 727-770
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 5
    facet.materialart.
    Unknown
    Docking devices for Soyuz-type spacecraft (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Two docking device designs for Soyuz-type spacecraft are compared. The first was flight tested successfully; the second achieves rigid and exact joining of two spacecraft, while incorporating changes to allow for the intravehicular transfer of crew members. The main functions of the docking device are considered, with the means by which they are accomplished, and measures for increasing its reliability and flexibility in service are noted.
    Keywords: SPACE VEHICLES
    Type: 6th Aerospace Mech. Symp.; p 143-150
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 6
    facet.materialart.
    Unknown
    Aerospace transporter and lifting body activities in Europe and potential participation in the development of the space shuttle orbiter (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The course of European aerospace research regarding reentry problems is briefly reviewed for the period from 1966 up to the present. The considerable experience gained by Europe, and particularly Germany, is shown to have led to their involvement and participation in the U.S. space shuttle program. The areas of investigation and expected contributions by European cooperation in the shuttle program are outlined.
    Keywords: SPACE VEHICLES
    Type: NASA. Langley Res. Center Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 969-995
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 7
    facet.materialart.
    Unknown
    Status of reusable surface insulation thermal protection system technology programs (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The development of three low-density rigidized insulation materials for the shuttle TPS application is reported. These materials consist of one high purity silica system and two systems based on mullite, an aluminum silicate. Both systems consist of fibers joined together with appropriate binders to obtain a rigidized insulation composite. Both material systems require the application of a glassy coating to provide a wear resistant, high emittance surface and to prevent the absorption of water by the fiber matrix. The technology program has addressed the development of water impervious coatings, methods of assembling the materials in design concepts while minimizing the thermal stress in the insulation, achieving compatibility between the RSI material and the structural system, and test evaluations to demonstrate the feasibility of the surface insulation concept.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 435-474
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 8
    facet.materialart.
    Unknown
    Overview of technology relative to the pogo instability on space shuttle (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The prediction of pogo contains a major source of uncertainty in the difficulty of defining the dynamic characteristics of certain components. An overview of the space shuttle technology with respect to each the following pogo problem areas is presented: structure, tank-liquid interaction, feedline, engine (pump), pogo-loop/control-loop interaction, and stability analysis.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 117-138
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 9
    facet.materialart.
    Unknown
    Assessment of potential buffet problems on the space shuttle vehicle (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Buffet of the space shuttle launch and reentry configuration is an area requiring continued evaluation to produce a safe reliable vehicle of minimum weight. Buffet forces result from flow separation and therefore can not be predicted accurately. Buffet loads are highly sensitive to configuration, angle of attack, and Mach number and can be reliably determined only by wind tunnel tests of elastically scaled models.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 25-43
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 10
    facet.materialart.
    Unknown
    Dynamic analysis for shuttle design verification (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Two approaches that are used for determining the modes and frequencies of space shuttle structures are discussed. The first method, direct numerical analysis, involves finite element mathematical modeling of the space shuttle structure in order to use computer programs for dynamic structural analysis. The second method utilizes modal-coupling techniques of experimental verification made by vibrating only spacecraft components and by deducing modes and frequencies of the complete vehicle from results obtained in the component tests.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 205-230
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 11
    facet.materialart.
    Unknown
    Surface studies on Surveyor 3 tubing sections (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Sections C and E of the unpainted, polished aluminum tubing from the strut of the radar altimeter and Doppler velocity sensor were examined in a transmission electron microscope for micrometeorite damage and ion bombardment. Both sections were contaminated and eroded on one side; it is suggested that these conditions were caused by sandblasting by lunar dust and retrorocket plume contamination during Surveyor 3 landing. Microcraters of different configurations were found on the bright sides of the tubes. Several degrees of violence were involved in the formation of the craters, and the particle size could be responsible for some differences. All micropits found were on the bright areas and data indicate 0.2 hypervelocity impact/sq cm and 2/sq cm for other types of craters. The greatest degree of damage resulted from particle impact and was limited to a maximum depth of 2 microns.
    Keywords: SPACE VEHICLES
    Type: NASA, Washington Analysis of Surveyor 3 Mater. and Phot. Returned by Apollo 12; p 154-158
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 12
    facet.materialart.
    Unknown
    Aerodynamic studies of delta-wing shuttle orbiters. Part 2: Hypersonics (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: An early version of an external hydrogen-oxygen tank orbiter was used as a baseline vehicle to experimentally evaluate: (1) nose shape and canopy effects on longitudinal, lateral, and directional stability and trim, and (2) yaw due to aerodynamic roll control at hypersonic speeds. Nose alterations were examined since that part of the vehicle may be subject to modifications because of internal packaging requirements, alleviation of potential high heating areas, and/or possible improvements in aerodynamic stability and control. There was also some concern about the effect of the rather high profile canopy on the aerodynamics; therefore its removal was examined. In addition, roll-yaw coupling was investigated because of its impact on the RCS fuel requirements for entry maneuvers.
    Keywords: SPACE VEHICLES
    Type: Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 803-830
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 13
    facet.materialart.
    Unknown
    Impact of subsonic aerodynamic considerations on a space shuttle booster configuration (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Considerations of cruise-back efficiency and subsonic flying qualities are shown to have resulted in a configuration with an aft high wing of moderate aspect ratio and with vertical tails located at the wing tips. The need to protect the air breathing engines during ascent and reentry and the desire for a low trim penalty longitudinal control surface led to consideration of a jet-flap canard. The advantages of this application of STOL technology to a space system are examined and the results of both wind tunnel tests and flight simulations are discussed. Since the use of the jet-flap canard concept offers the potential for a minimum weight vehicle, a proposed technology development program is outlined in order that the full benefit of this concept may be realized.
    Keywords: SPACE VEHICLES
    Type: NASA. Langley Res. Center Space Shuttle Aerothermodyn. Technol. Conf., vol.3; p 737-784
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 14
    facet.materialart.
    Unknown
    On the possibility of Earth reentry simulation of shallow angle Jupiter entry (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Possible Earth reentry simulation of shallow-angle (3 to 30 deg) Jupiter entry was investigated in terms of four parameters of the bow shock layer ahead of a blunt vehicle: peak (equilibrium) temperature, peak pressure, peak inward radiative flux, and time-integrated radiative flux. It is shown that simulation ranging from fair to good can be achieved. Reentry is easiest (lowest Earth reentry speed) at steep Earth reentry, in the Earth entry speed range of 15 to 22 km/sec, for both the Jupiter nominal and cool atmospheres. Increased Earth speed is required, generally, for increasing Jupiter entry angle, and for increasing temperature, radiative flux, time-integrated flux and pressure, in that order.
    Keywords: SPACE VEHICLES
    Type: JPL Quart. Tech. Rev., Vol. 1, No. 4; p 19-29
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 15
    facet.materialart.
    Unknown
    Application of composite materials to space shuttle tanks (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Tanks are broken down into two categories: pressure vessels that carry primarily pressure loads, and structural tanks that carry structural loads such as thrust or bending in addition to pressure. A significant portion of the shuttle orbiter structure are tanks and in order to minimize both weight and cost growth on these shuttle tank structures, composite material tanks of both types are considered.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 573-603
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 16
    facet.materialart.
    Unknown
    Advanced design concepts for shuttle airframe structure (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The development of weight-saving advanced design concepts for shuttle airframe structure is presented. Design concepts under investigation employ selective composite reinforcement and/or efficient geometric arrangements. An effort to develop metallic panel designs which exploit the relaxation of smooth external-surface requirements for skin structure is reviewed. Available highlights from research and development studies which investigate the application of composite reinforcement to the design of two types of fuselage panels, a shear web, a large fuselage frame, and a landing-gear-door assembly are presented. Preliminary results from these studies suggest weight savings of 25 percent can be obtained.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 537-572
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 17
    facet.materialart.
    Unknown
    In-flight aeroacoustic environments on prospective space shuttle vehicles (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The problem of in-flight aerodynamic noise has been studied by reliable estimates of full scale surface-pressure fluctuations from scale model tests in wind tunnels. Scaling relationships have been verified, and many details of the fluctuating pressure characteristics such as spatial correlation and convection velocities are understood. The effects of the wind tunnel environmental turbulence and noise have also been investigated sufficiently so that threshold levels of usable data are known.
    Keywords: AERODYNAMICS
    Type: NASA Space Shuttle Technol. Conf.; p 71-96
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 18
    facet.materialart.
    Unknown
    Flutter technology for space shuttle (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The development of analytical and experimental techniques needed to predict space shuttle flutter boundaries and insure adequate flutter margins and anticipated problems associated with aeroelastic-model and full-scale testing to validate flutter clearance are considered. Results illustrating the best available tools for subsonic and supersonic flutter prediction are presented. Programs currently underway which will help overcome the difficult problems envisioned for the transonic wind-tunnel and flight flutter test program are also discussed.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 1-24
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 19
    facet.materialart.
    Unknown
    Gas-powered reentry body erection mechanism (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The design, analysis, testing, and flight of the supersonic planetary entry decelerator 2 spacecraft are described. The vehicle was launched in a folded condition and deployed to its required configuration following exit from the atmosphere. This concept was selected primarily because it allows utilization of existing launch vehicle systems in the most economical manner possible.
    Keywords: SPACE VEHICLES
    Type: 6th Aerospace Mech. Symp.; p 101-107
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 20
    facet.materialart.
    Unknown
    Satellite temperature correlation of predicted, test, and flight data (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: This study compares satellite temperature predictions with thermal vacuum test results and shows the improvement from testing. Orbital data were compared with prediction/test results to determine quantitatively an expected error criteria.
    Keywords: SPACE VEHICLES
    Type: NASA. Goddard Space Flight Center Space Simulation; p 425-443
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 21
    facet.materialart.
    Unknown
    Experiments on the dynamic stability of the space shuttle (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Some dynamic stability experiments on the space shuttle using a half-model oscillatory technique are discussed. Resulting information from the experiments is presented and includes: (1) dynamic pitching characteristics of both the orbiter and the booster alone as well as of the two models mated into a single launch configuration; (2) the static and dynamic interference effects during an abort separation maneuver; and (3) the dynamic plume interference effect.
    Keywords: SPACE VEHICLES
    Type: NASA. Langley Res. Center Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 933-968
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 22
    facet.materialart.
    Unknown
    Dynamic testing for shuttle design verification (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Space shuttle design verification requires dynamic data from full scale structural component and assembly tests. Wind tunnel and other scaled model tests are also required early in the development program to support the analytical models used in design verification. Presented is a design philosophy based on mathematical modeling of the structural system strongly supported by a comprehensive test program; some of the types of required tests are outlined.
    Keywords: SPACE VEHICLES
    Type: NASA Space Shuttle Technol. Conf.; p 231-265
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 23
    facet.materialart.
    Unknown
    Neuter docking mechanism study (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Neuter (or androgynous) docking systems that allow space vehicles with similar or identical docking hardware to dock are discussed. Basic requirements applicable to docking mechanism design, four neuter concepts that were studied, and the concept selected by the NASA Manned Spacecraft Center for detailed investigation are presented.
    Keywords: SPACE VEHICLES
    Type: 6th Aerospace Mech. Symp.; p 43-49
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 24
    facet.materialart.
    Unknown
    Aerodynamic studies of delta-wing shuttle orbiters. Part 1: Low speed (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Numerous wind tunnel tests conducted on the evolving delta-wing orbiters have generated a fairly large aerodynamic data base over the entire entry operation range of these vehicles. A limited assessment is made of some of the aerodynamics of the current HO type orbiters, and several specific problem areas selected from the broad data base are discussed. These include, from a subsonic viewpoint, discussions of trim drag effect; effects of the installation of main rocket engine nozzles, OMS and RCS packages, Reynolds number effects, lateral-directional stability characteristics, and landing characteristics.
    Keywords: SPACE VEHICLES
    Type: Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 785-802
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 25
    facet.materialart.
    Unknown
    Wing optimization for space shuttle orbiter vehicles (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: The results were presented of a parametric study performed to determine the optimum wing geometry for a proposed space shuttle orbiter. The results of the study establish the minimum weight wing for a series of wing-fuselage combinations subject to constraints on aerodynamic heating, wing trailing edge sweep, and wing over-hang. The study consists of a generalized design evaluation which has the flexibility of arbitrarily varying those wing parameters which influence the vehicle system design and its performance. The study is structured to allow inputs of aerodynamic, weight, aerothermal, structural and material data in a general form so that the influence of these parameters on the design optimization process can be isolated and identified. This procedure displays the sensitivity of the system design of variations in wing geometry. The parameters of interest are varied in a prescribed fashion on a selected fuselage and the effect on the total vehicle weight is determined. The primary variables investigated are: wing loading, aspect ratio, leading edge sweep, thickness ratio, and taper ratio.
    Keywords: SPACE VEHICLES
    Type: NASA. Langley Res. Center Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 831-860
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 26
    facet.materialart.
    Unknown
    Status of Langley studies of aerodynamics and interference effects of tandem launch vehicles (1972)
    In:  CASI
    Details
    Publication Date: 2005-11-30
    Description: Some of the aerodynamic and interference effects measured from wind-tunnel tests of three fully reusable space shuttle configurations at transonic and low-supersonic speeds are presented, and the status is given of an assessment of the analytical approach to date. The three configurations tested were a low-fineness-ratio booster combined in tandem with a delta-wing orbiter, designated the "low-fineness-ratio configuration,' and a phase B shuttle configuration consisting of the delta-wing orbiter and high-fineness-ratio booster, designated the "stage-arrangement configuration,' arranged in tandem and in parallel. The force measurements obtained at a Mach number of 1.5 for the low-fineness-ratio configuration were representative of the transonic and low-supersonic speed ranges where the interference effects are predominant and were used for comparison with values calculated at the same Mach number. This comparison is the basis for a preliminary assessment of the initial application of the analytical approach.
    Keywords: SPACE VEHICLES
    Type: Space Shuttle Aerothermodyn. Technol. Conf., vol. 3; p 707-736
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 27
    facet.materialart.
    Unknown
    Some contamination problems in the European TD satellite (1972)
    In:  CASI
    Details
    Publication Date: 2009-11-16
    Description: Materials were selected for the European TD satellite with a view to avoiding contamination of its stellar ultraviolet telescopes. Materiels were selected using the micro-VCM technique, and some typical cases of materials evaluation are described. The cleanliness of the satellite was monitored during integration and test phases, and in particular during long duration thermal vacuum tests.
    Keywords: SPACE VEHICLES
    Type: NASA. Goddard Space Flight Center Space Simulation; p 613-627
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 28
    facet.materialart.
    Unknown
    Summary and future plans (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 121-133
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 29
    facet.materialart.
    Unknown
    Piloting and operational aspets of the F-8 supercritical wing airplane (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 97-110
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 30
    facet.materialart.
    Unknown
    Status of the F-8 supercritical wing program (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 49-58
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 31
    facet.materialart.
    Unknown
    F-8 supercritical wing pressure distribution evaluation (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 71-84
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 32
    facet.materialart.
    Unknown
    Buffet characteristics of the F-8 supercritical wing airplane (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 85-96
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 33
    facet.materialart.
    Unknown
    The NASA supercritical airfoil and its application to swept wings (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 1-12
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 34
    facet.materialart.
    Unknown
    Evolution of the F-8 supercritical wing configuration (1972)
    In:  CASI
    Details
    Publication Date: 2004-12-03
    Keywords: AERODYNAMICS
    Type: Supercritical Wing Technol.: A Report on Flight Evaluation; p 35-48
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 35
    facet.materialart.
    Unknown
    Status of advanced airfoil tests in the Langley 0.3-meter transonic cryogenic tunnel (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A joint NASA/U.S. industry program to test advanced technology airfoils in the Langley 0.3-meter Transonic Tunnel (TCT) was formulated under the Langley ACEE Project Office. The objectives include providing U.S. industry an opportunity to compare their most advanced airfoils to the latest NASA designs by means of high Reynolds number tests in the same facility. At the same time, industry would again experience in the design and construction of cryogenic test techniques. The status and details of the test program are presented. Typical aerodynamic results obtained, to date, are presented at chord Reynolds number up to 45 x 10(6) and are compared to results from other facilities and theory. Details of a joint agreement between NASA and the Deutsche Forschungs- und Versuchsantalt fur Luft- and Raumfahrt e.V. (DFVLR) for tests of two airfoils are also included. Results of these tests will be made available as soon as practical.
    Keywords: AERODYNAMICS
    Type: Advan. Aerodyn.: Selected NASA Res.; p 37-53
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 36
    facet.materialart.
    Unknown
    Component testing for dynamic model verification (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Dynamic model verification is the process whereby an analytical model of a dynamic system is compared with experimental data, adjusted if necessary to bring it into agreement with the data, and then qualified for future use in predicting system response in a different dynamic environment. These are various ways to conduct model verification. The approach taken here employs Bayesian statistical parameter estimation. Unlike curve fitting, whose objective is to minimize the difference between some analytical function and a given quantity of test data (or curve), Bayesian estimation attempts also to minimize the difference between the parameter values of that funciton (the model) and their initial estimates, in a least squares sense. The objectives of dynamic model verification, therefore, are to produce a model which: (1) is in agreement with test data; (2) will assist in the interpretation of test data; (3) can be used to help verify a design; (4) will reliably predict performance; and (5) in the case of space structures, will facilitate dynamic control.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Recent Experiences in Multidisciplinary Analysis and Optimization, Part 2; 15 p
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 37
    facet.materialart.
    Unknown
    Post and a random-walk search mode (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Multidisciplinary analysis often requires optimization of nonlinear systems that are subject to constraints. Trajectory optimization is one example of this situation. The Program to Optimize Simulated Trajectories (POST) was used successfully for a number of problems. The purpose is to describe POST and a new optimization approach that has been incorporated into it. Typical uses of POST will also be illustrated. The projected-gradient approach to optimization is the preferred option in POST and is discussed. A new approach to optimization, the random-walk approach, is described, and results with the random-walk approach are presented.
    Keywords: AERODYNAMICS
    Type: Recent Experiences in Multidisciplinary Analysis and Optimization, Part 2; 23 p
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 38
    facet.materialart.
    Unknown
    Wall interference measurements for three-dimensional models in transonic wind tunnels: Experimental difficulties (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The purpose is not to provide a detailed discussion of several wall interference experiments, but rather to use these experiments (recently accomplished in the Boeing Transonic Wind Tunnel (BTWT) to illustrate the problems associated with many of the measurements required by current wall interference assessment/correction (WIAC) procedures. The wall correction to lift is emphasized. It is shown that, because conventional tunnels and relatively small models continue to be used, the flow field or flow boundary measurements to be made impose severe requirements on the experiment itself. In some cases, existing instrumentation and test techniques may not be adequate to obtain the data accuracies needed.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 21-42
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 39
    facet.materialart.
    Unknown
    Adaptation of a four-wall interference assessment/correction procedure for airfoil tests in the 0.3-m TCT (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Based upon limited, initial observations of wall interference corrections obtained for one airfoil test, there is a need for assessing the upstream flow direction. If there is no direct measurement then a two-pass correction procedure similar to the one described here is required. Questions have arisen pertaining to the correct interpretation of the pressure coefficients measured on the slats of a slotted tunnel wall, the interpretation of just what the calculated equivalent body encompasses or should include, and what can or should be considered as quantitative criteria for data correctability. Further studies using this modified procedure will address these questions. Hopefully, a meaningful WIAC procedure can be validated for the airfoil tests in the 0.3-m TCT.
    Keywords: AERODYNAMICS
    Type: Wind Tunnel Wall Interference Assessment and Correction, 1983; p 393-414
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 40
    facet.materialart.
    Unknown
    Some experience with Barnwell-Sewall type correction to two-dimensional airfoil data (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A series of airfoils were tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT) at Reynolds numbers from 2 to 50 million. The 0.3-m TCT is equipped with Barnwell slots designed to minimize blockage due to the tunnel flow and ceiling. This design suggests that sidewall corrections for blockage is needed, and that a lifting airfoil produces a change in angle of attack. Sidewall correction methods were developed for subsonic and subsonic-transonic flow. Comparisons of theory with experimental data obtained in the 0.3-m TCT for two airfoils, the British NPL 9510 and the German R-4 are presented. The NPL 9510 was tested as part of the NASA/United Kingdom Joint Aeronautical Program and R-4 was tested as part f the DFVLR/NASA Advanced Airfoil Research Program. For the NPL 9510 airfoil, only those test points that one would anticipate being difficult to predict theoretically are presented.
    Keywords: AERODYNAMICS
    Type: Wind Tunnel Wall Interference Assessment and Correction, 1983; p 375-392
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 41
    facet.materialart.
    Unknown
    Experiences with a high-blockage model tested in the NASA Ames 12-foot pressure wind tunnel (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Representation of the flow around full-scale ships was sought in the subsonic wind tunnels in order to a Hain Reynolds numbers as high as possible. As part of the quest to attain the largest possible Reynolds number, large models with high blockage are used which result in significant wall interference effects. Some experiences with such a high blockage model tested in the NASA Ames 12-foot pressure wind tunnel are summarized. The main results of the experiment relating to wind tunnel wall interference effects are also presented.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 345-360
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 42
    facet.materialart.
    Unknown
    An inerference assessment approach for a three-dimensional slotted tunnel with sparse wall pressure data (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The various procedures referred to as wall interference assessment and correction procedures presume the existence of a surface distribution of data (usually static pressure) measured over a surface on or near the tunnel walls for each test point to be assessed. An alternative approach in which a reasonably sophisticated computer model of the test section flow would be fitted parametrically to a sparse set of measured data is presented. The measurements provides line distributions of static pressure near the center lines of the top, side and bottom walls. The development of a test section model incorporating explicit recognition of discrete slots of finite length with controlled flow reentry into the solid wall downstream portion of the tunnel is shown.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center. Wind Tunnel Wall Interference Assessment and Correction, 1983; p 323-334
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 43
    facet.materialart.
    Unknown
    EBF noise tests with engine under-the-wing and over-the-wing configurations (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Noise tests of externally blown flaps with the engine under the wing and engine over the wing configurations were conducted. Flap noise data obtained on a TF-34 aircraft are discussed. Noise data obtained during a free-jet forward-speed-effect analysis are presented. Noise sources associated with upper surface flap blowing are described. Results of a small scale configuration screening study and some large scale model test data are analyzed. The noise data for the engine over wing configurations are compared with the engine under the wing configurations.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 455-473
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 44
    facet.materialart.
    Unknown
    Flap noise generation and control (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: The characteristics of aerodynamic noise generated by the interaction of an airstream with a flap surface are discussed. The location and behavior of various noise sources were investigated to determine optimal quieting techniques. A schematic diagram of the jet-flap concepts being considered for integrated-powered-lift systems for short takeoff aircraft is shown. Each of the concepts has in common high velocity turbulent air flowing over relatively rigid surfaces with resultant production of interaction noise. The nature, location, and control of noise sources which involve the interactions of air flows with airfoil surfaces are examined.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 413-426
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 45
    facet.materialart.
    Unknown
    Acoustic characteristics of large-scale STOL models at forward speed (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Wind-tunnel investigations of the acoustic characteristics of the externally blown jet flap (EBF) and augmentor wing STOL concepts are discussed. The large-scale EBF model was equipped with a triple-slotted flap blown by four JT15D turbofan engines with circular, coannular exhaust nozzles. The large-scale augmentor wing model was equipped with an unlined augmentor blown by a slot primary nozzle. The effects of airspeed and angle of attack on the acoustics of the EBF were small. Flap deflection had a greater effect on the acoustics of the augmentor wing than did airspeed. The total sound power was also significantly higher for landing indicating that turning in the augmentor generated acoustic energy. Airspeed produced a small aft shift in acoustic directivity with no significant change in the peak perceived noise levels or sound power levels. Small-scale research of the acoustics for the augmentor wing has shown that by blowing an acoustically treated augmentor with a lobed primary nozzle, the 95-PNdb noise level goal can be achieved or surpassed.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 443-454
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 46
    facet.materialart.
    Unknown
    Externally blown flap impingement noise (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Tests of the noise produced by the impingement of the jet exhaust on the wing and flap for an externally blown flap system were conducted with a CF700 turbofan engine and an F-111B wing panel. The noise produced with a daisy nozzle installed on the engine was greater than that produced by a conical nozzle at the same thrust. The presence of the wing next to the test nozzles increased the noise, as did increasing the flap deflection angle. Compared with the conical nozzle, the daisy nozzle produced slightly less noise at a flap deflection of 60 deg but produced more noise at the lower flap deflections tested. Tests showed that the single-slotted flap deflected 60 deg, produced less noise than the double-slotted flaps. Also, maintaining the maximum distance between the exit nozzle and flap system resulted in a minor reduction in noise.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 427-441
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 47
    facet.materialart.
    Unknown
    Survey of wing and flap lower-surface temperatures and pressures during full-scale ground tests of an externally blown flap system (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Full-scale ground tests of an externally blown flap system were made using the wing of an F-111B airplane and a CF700 engine. Pressure and temperature distributions were determined on the undersurface of the wing, vane, and flap for two engine exhaust nozzles (conical and daisy) at several engine power and engine/wing positions. The tests were made with no airflow over the wing. The leading-edge wing sweep angle was fixed at 26 deg, the angle of incidence between the engine and the wing was fixed at 3 deg, and the tests were conducted with the flap retracted, extended and deflected 35 deg, and extended and deflected 60 deg. The integrated local pressures on the undersurface of the flap produced loads approximately three times as great at the 60 deg flap position as at the 35 deg flap position. With both nozzle configurations, more than 90 percent of the integrated pressure loads were contained within plus or minus 20 percent of the flap span centered around the engine exhaust centerline. The maximum temperature recorded on the flaps was 218 C (424 F) for the conical nozzle and 180 C (356 F) for the daisy nozzle.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 143-156
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 48
    facet.materialart.
    Unknown
    Simulator evaluation of the flying qualities of externally blown flap and augmentor wing transport configurations (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Concurrent simulations of powered-lift STOL transport aircraft having either an externally blown flap configuration or an augmentor wing configuration were conducted. The following types of simulators of varying sophistication were used: (1) a simple fixed-base simulation with a simple visual display, (2) a more complex fixed-base simulation using a realistic transport cockpit and a high-quality visual display, and (3) a six-degree-of-freedom motion simulator that had a realistic transport cockpit and a sophisticated visual display. The unaugmented flying qualities determined from these simulations were rated as unacceptable for both the externally blown flap and augmentor wing configurations. The longitudinal, lateral-directional, and single-engine-failure characteristics were rated satisfactory with extensive augmentation, including pitch and roll command systems, flight-path (or speed) augmentation, turn coordination, and effective yaw damping. However, the flare and landing characteristics from any approach glide-path angle in excess of 4 deg were rated as unsatisfactory but acceptable.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 157-800
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 49
    facet.materialart.
    Unknown
    Aerodynamics of the upper surface blow flap (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: The results of some preliminary wind-tunnel investigations made to provide fundamental aerodynamic information on the upper surface blown jet-flap concept incorporating high-bypass-ratio turbofan engines are summarized. The results of the investigation have shown the concept to have aerodynamic performance generally similar to that of other externally blown high-lift systems. A few of the more critical problems associated with this concept have been identified and preliminary solutions to some of these problems have been found. These results have proven to be sufficiently encouraging to warrant continuation of fundamental research efforts on the concept.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Res. Center STOL Technol.; p 97-110
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 50
    facet.materialart.
    Unknown
    Advanced augmentor-wing research (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Results of research on advanced augmentors are discussed. Research concerned with performance has indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles, (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest, and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data has shown that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 87-96
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 51
    facet.materialart.
    Unknown
    Aerodynamic characteristics of a swept augmentor wing (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: A brief outline of augmentor wing research sponsored by Ames Research Center is presented and is followed by a discussion of large-scale wind-tunnel test results for a swept augmentor wing configuration. The results showed that the augmentor wing could be applied to high-speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 71-86
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 52
    facet.materialart.
    Unknown
    Aerodynamic loads measurements on externally blown flap STOL models (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: Small-scale-model data have shown large static loads on the flap system behind the engines. The large-scale-model tests confirmed the magnitude of these loads and indicated that the relative loading of each flap element depends on the engine-wing-flap geometry. Flap response measurements indicated that the unsteady pressure loading excited the natural vibration modes of the flap system on this model. Since this was a boilerplate model, the only conclusion that can be drawn is that the possibility of large vibration loads must be considered for a flight-weight structure. The similarity of the unsteady pressure and flap response spectra for the wind-off and wind-on cases indicated that it may be possible to realistically test flight-weight flap structures on a static test stand rather than endure the extra costs and scheduling problems associated with large-scale wind-tunnel tests. There is a potential flap-temperature problem which if not resolved might preclude the use of materials such as aluminum and the composites in the flap structure.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 121-130
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 53
    facet.materialart.
    Unknown
    Aerodynamic and performance characteristics of externally blown flap configurations (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: The application of externally blown flaps for improving the performance of short takeoff aircraft is discussed. The characteristics of externally blown flap powered lift are examined. A method for predicting the aerodynamic performance of a particular externally blown flap configuration is presented. The following specific effects are analyzed: (1) induced aerodynamics, (2) static turning, (3) flap span and deflection, and (4) engine size and chord flap.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 43-54
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 54
    facet.materialart.
    Unknown
    Stability and control of externally blown flap configurations (1972)
    In:  CASI
    Details
    Publication Date: 2006-03-27
    Description: The results of wind-tunnel investigations on the stability and control characteristics of externally blown jet-flap configurations are presented. Conventional wind-tunnel tests and free-flight model tests have shown that longitudinal trim and stability can be achieved by a properly located horizontal tail of sufficient size, and that lateral trim in the engine-out condition can be produced by combinations of differential flap, spoiler, and rudder deflection. Free-flight model tests have revealed a lightly damped Dutch roll lateral oscillation, and have shown that the oscillation can be stabilized by use of artificial damping.
    Keywords: AERODYNAMICS
    Type: STOL Technol.; p 55-70
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 55
    facet.materialart.
    Unknown
    Interference from slotted walls (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Wall interference is made predominant in tunnel models and by wall geometries to facilitate the study of slot flow. The viscous effects in slots are studied by two dimensional measurements of flow. Wall interference is assessed by measuring pressure distributions at two levels near the walls. Interference on lifting delta wings is calculated. Pressure distributions at inner boundaries show basis axisymetries between the pressure side and the suction side, pointing to the necessity of having wider slots on the pressure side.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 293-300
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 56
    facet.materialart.
    Unknown
    Development in UK of a method for calculating tunnel wall corrections from flow measurements (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Classical methods for calculation of wall corrections which are not satisfactory for a number of flows of interest are discussed. To meet these objections, a number of methods were developed which use measurements of the low at or close to the tunnel walls as an outer boundary condition to define wall interference. The development, assessment and application of one such method is summarized.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 259-271
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 57
    facet.materialart.
    Unknown
    NLR activities in the field of wind tunnel wall interference (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Measured field data as a boundary condition for calculating the interference flow field were applied. They are divided into two categories. In the first category, the field data must consist of distributions of a single velocity component, and an accurate estimate of the hypothetical free air contribution of the model to this component is required. The differences between measured values and estimated model contributions are attributed to wall interference and they establish the boundary condition. The associated field data measurements are simple, yet the necessary model representation generally is a serious drawback. The second category requires field data which consist of velocity vector distributions at the price of multicomponent measurements, but at the profit that no information at all is required about the model. In solid wall test sections, the price is reduced to virtually zero but the profit remains.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 221-229
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 58
    facet.materialart.
    Unknown
    Performance of two transonic airfoil wind tunnels utilizing limited ventilation (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A limited-zone ventilated wall panel was developed for a closed-wall icing tunnel which permitted correct simulation of transonic flow over model rotor airfoil sections with and without ice accretions. Candidate porous panels were tested in the Ohio State University 6- x 12-inch transonic airfoil tunnel and result in essentially interference-free flow, as evidenced by pressure distributions over a NACA 0012 airfoil for Mach numbers up to 0.75. Application to the NRC 12- x 12-inch icing tunnel showed a similar result, which allowed proper transonic flow simulation in that tunnel over its full speed range.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 165-170
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 59
    facet.materialart.
    Unknown
    Investigations of flow field perturbations induced on slotted transonic-tunnel walls (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The free-stream interference caused by the flow through the slotted walls of the test sections of transonic wind tunnels has continuously a problem in transonic tunnel testing. The adaptive-wall transonic tunnel is designed to actively control the near-wall boundary conditions by sucking or blowing through the wall. In order to make the adaptive-wall concept work, parameters for computational boundary conditions must be known. These parameters must be measured with sufficient accuracy to allow numerical convergence of the flow field computations and must be measured in an inviscid region away from the model that is placed inside the wind tunnel. The near-wall flow field was mapped in detail using a five-port cone probe that was traversed in a plane transverse to the free-stream flow. The initial experiments were made using a single slot and recent measurements used multiple slots, all with the tunnel empty. The projection of the flow field velocity vectors on the transverse plane revealed the presence of a vortex-like flow with vorticity in the free stream. The current research involves the measurement of the flow field above a multislotted system with segmented plenums behind it, in which the flow is controlled through several plenums simultaneously. This system would be used to control a three-dimensional flow field.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 119-142
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 60
    facet.materialart.
    Unknown
    Assessment of lift- and blockage-induced wall interference in a three-dimensional adaptive-wall tunnel (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A three-dimensional adaptive-wall wind tunnel experiment was conducted at Ames Research Center. This experiment demonstrated the effects of wall interference on the upwash distribution on an imaginary surface surrounding a lifting wing. This presentation demonstrates how the interference assessment procedure used in the adaptive-wall experiments to determine the wall adjustments can be used to separately assess lift- and blockage-induced wall interference in a passive-wall wind tunnel. The effects of lift interference on the upwash distribution and on the model lift coefficient are interpreted by a simple horseshoe vortex analysis.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 89-100
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 61
    facet.materialart.
    Unknown
    Wind tunnel wall interference in closed, ventilated and adaptive test sections (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A wall interference correction method for closed rectangular test sections was developed which uses measured wall pressures. Measurements with circular discs for blockage and a rectangular wing as a lift generator in a square closed test section validate this method. These measurements are intended to be a basis of comparison for measurements in the same tunnel using ventilated (in these case, slotted) walls. Using the vortex lattice method and homogeneous boundary conditions, calculations were performed which show sufficiently high pressure levels at the walls for correction purposes in test sections with porous walls. In Gottingen, an adaptive test section (which is a deformable rubber tube of 800 mm diameter) was built and a computer program was developed which is able to find the necessary wall adaptation for interference-free measurements in a single step. To check the program prior to the first run, the vortex lattice method was used to calculate wall pressure distributions in the nonadapted test section as input data for the one-step method. Comparison of the pressure distribution in the adapted test section with free-flight data shows nearly perfect agreement. An extension of the computer program can be made to evaluate the remaining interference corrections.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 61-78
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 62
    facet.materialart.
    Unknown
    Review of the advanced technology airfoil test program in the 0.3-meter transonic cryogenic tunnel (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The following areas were addressed: interchangeable test sections in the 0.3-M Transonic Cryogenic Tunnel (TCT); typical airfoil installation; airfoil capability; advanced technology airfoil test (ATAT); effects of the Reynolds number on the normal force coefficient; effects of the Reynolds number on the drag coefficient; and comparison of experimental results with theory.
    Keywords: AERODYNAMICS
    Type: Wind Tunnel Wall Interference Assessment and Correction, 1983; p 361-374
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 63
    facet.materialart.
    Unknown
    Determination of equivalent model geometry for tunnel wall interference assessment/correction (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A formula for the determination of equivalent model geometry with two variables measured at the interface is derived, based on two dimensional subsonic flow. This predicted model profile is a reasonable initial estimate for transonic flow as long as the sonic region does not reach the interface. A general formula is given in two forms. One is in terms of complex variable functions and the other is an integral equation. The complex-function formula has the advantage of using analytic expressions. The integral equation form requires a numerical solution after assuming the model geometry as a polynomial function. Examples are given to illustrate the application of the formulas.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 335-342
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 64
    facet.materialart.
    Unknown
    Wind tunnel wall interference correction for aircraft models (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Wall interference correction procedures seek to determine the required changes in certain flow or geometric parameters so that the difference between the flow properties at the model's surface in the tunnel and free air are minimized. A transonic and a linear correction procedure were developed for aircraft models. In addition to Mach number and angle of attack corrections, an estimate of the accuracy of the corrections is provided by the transonic correction procedure. Lift, pitching moment and pressure measurements near the tunnel walls are required. The efficiency and accuracy of the correction procedure are improved. Moreover, correction of both the wing and tail angles of attack is allowed. The procedure is valid for transonic as well as subcritical flows. However, for subcritical flows further approximations and simplifying assumptions are made, leading to a very simple and efficient correction procedure.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center. Wind Tunnel Wall Interference Assessment and Correction, 1983; p 301-322
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 65
    facet.materialart.
    Unknown
    Tunnel constraint for a jet in crossflow (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A facet of a unified tunnel correction scheme which uses wall pressures to determine tunnel induced blockage and upwash is described. With this method, there is usually no need to use data concerning model forces or power settings to find the interference; it follows directly from the pressures and tunnel dimensions. However, highly inclined jets do not produce good pressure signatures and are highly three dimensional, so they must be treated differently. Flow modeling is also discussed.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center. Wind Tunnel Wall Interference Assessment and Correction, 1983; p 273-290
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 66
    facet.materialart.
    Unknown
    Progress in wind tunnel wall interference assessment/correction procedures at the NAE (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Wall corrections as a function of wall porosity in the transonic wall interference problem was assessed. Effective porosities primarily for the two dimensional case were established as follows: (1) comparison of experimental data for two geometrically similar models of different chord/height ratio, an overall value of wall porosity could be deduced; (2) theoretical development which allows for unequal porosity for the floor and ceiling and wall boundary pressure measurements, porosities for floor and ceiling could be deduced; (3) a scheme was developed which allowed unequal porosity of floor and ceiling and streamwise varying porosity. The boundary layer development along the perforated floor and ceiling under the influence of the model pressure field, variations in boundary layer thickness underlining the difficulties in deducing meaningful values of wall porosity were determined. Wall boundary pressure measurement, in combination with singularity modelling of the airfoil, was sufficient to yield required information on the wall interference flow without having to establish some value for wall porosity. The singularity modelling of the airfoil initially covered only lift and volume but was extended to include drag and pitching moment, and second order volume term. It is shown by asymptotic transonic small disturbance analysis, that the derived corrections to angle of attack and free stream Mach number are correct to the first order.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 231-257
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 67
    facet.materialart.
    Unknown
    Asymptotic methods for wind tunnel wall corrections at transonic speed (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The effort to develop classical methods to compute wall interference at transonic speeds is outlined. The two-dimensional theory and three-dimensional development are discussed. Also, some numerical application of the two-dimensional work are indicated. The basic advantages of the asymptotic theory are noted.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 193-203
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 68
    facet.materialart.
    Unknown
    Effect of boundary layers on solid walls in three-dimensional subsonic wind tunnels (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A solution for the tunnel wall boundary layer effects for three-dimensional subsonic tunnels is presented. The model potentials are represented with simple singularities placed on the centerline of the tunnel and Laplace's equation in cylindrical coordinates is solved for either the conventional homogeneous slotted-wall boundary condition, the solid-wall viscous boundary condition, or a combination of them. The most pronounced wall boundary layer effect is on solid blockage for completely closed wind tunnels. Boundary layers on the wall reduce the blockage from the solid-wall, no-boundary-layer case in a manner similar to opening slots in a solid wall. Additionally, for solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, whereas the lift interference factor at the model station does not depend on the boundary layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.
    Keywords: AERODYNAMICS
    Type: Wind Tunnel Wall Interference Assessment and Correction, 1983; p 205-218
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 69
    facet.materialart.
    Unknown
    Experiments suitable for wind tunnel wall interference assessment/correction (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Three experiments suitable for wall interference assessment and evaluation of proposed correction methods are presented. The experiments are: (1) a series of airfoil tests using a newly designed transonic flow facility that employs side-wall boundary layer suction and upper- and lower-wall shaping; (2) tests on a swept airfoil section spanning a solid-wall wind tunnel with fixed contouring on all four walls; and (3) tests on a swept wing of aspect ratio 3 mounted in a solid-wall wind tunnel with fixed flat walls. Each of the experiments provides data on the airfoil sections as well as on the wind tunnel walls. All the experiments were performed in solid wall wind tunnels corrected for boundary layer displacement effects. Although the experiments were performed primarily to evaluate computer code performance, it is believed that they also provide information that can be used to evaluate methods for assessing and correcting wall interference effects.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 171-190
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 70
    facet.materialart.
    Unknown
    Effect of upstream sidewall boundary layer removal on an airfoil test (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: Sidewall boundary layer effects were investigated by applying partial upstream sidewall boundary layer removal in the Langley 0.3-m transonic cryogenic tunnel. Over the range of sidewall boundary layer displacement thickness of these tests the influence on pressure distribution was found to be small for subcritical conditions; however, for supercritical conditions the shock position was affected by the sidewall boundary layer. For these tests (with and without boundary layer remove) comparisons with predictions of the GRUMFOIL computer code indicated that Mach number corrections due to the sidewall boundary layer improve the agreement for both subcritical and supercritical conditions. The results also show that sidewall boundary layer removal reduces the magnitude of the sidewall correction; however, a suitable correction must still be made.
    Keywords: AERODYNAMICS
    Type: Wind Tunnel Wall Interference Assessment and Correction, 1983; p 143-163
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 71
    facet.materialart.
    Unknown
    A data base for three-dimensional all-interference code evaluation (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: A validation of a measured boundary condition technique was carried out to demonstrate the feasibility of a wall interference assessment/correction (WIAC) system. An experimental evaluation was also carried out to compare performances of various techniques, to define the number of necessary boundary measurements for accurate assessment/corrections and to define the envelope of test conditions for which accurate assessment/corrections are achieved. The relative merits of a WIAC system and an adaptive wall tunnel are compared. The measurement surface boundary data is performed with a system of two rotating pipes. These pipes sweep out a cylindrical measurement surface near the tunnel walls, approximately one inch from the wall at the closest point. The experimental model was specially designed and fabricated for the adaptive wall experiments. The model is a wing/tail/body configuration with swept lifting surface. The boundary data taken in Tunnel 1T with the rotating pipe system has been shown to offer several attractive features for WIAC code evaluation. Good spatial resolution of measurements is achieved and measurements are made upstream and downstream of the model. Also, two velocity components are determined.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 101-118
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 72
    facet.materialart.
    Unknown
    Survey of ONERA activities on adaptive-wall applications and computation of residual corrections (1984)
    In:  CASI
    Details
    Publication Date: 2006-02-14
    Description: The research undertaken concerning the computation and/or reduction of wall interference follows two main axes: improvement of wall correction determinations, and use of adaptive flexible walls. The use of wall-measured data to compute interference effects is reliable when the model representation is assessed by signatures with known boundary conditions. When the computed interferences are not easily applicable to correcting the results (especially for gradients in two-dimensional cases), the flexible adaptive walls in operation in T2 are an efficient and assessed means of reducing the boundary effects to a negligible level, if the direction and speed of the flow are accurately measured on the boundary. The extension of the use of adaptive walls to three-dimensional cases may be attempted since the residual corrections are assumed to be small and are computable.
    Keywords: AERODYNAMICS
    Type: NASA. Langley Research Center Wind Tunnel Wall Interference Assessment and Correction, 1983; p 43-60
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 73
    facet.materialart.
    Unknown
    Viscous transonic flow computation over Space Shuttle configuration (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-19
    Description: A thin-layer Navier-Stokes code capable of predicting steady-state viscous flows is applied to the transonic flow over a Space Shuttle configuration. The code is written in the generalized coordinate system, and the grid-generation code of Fujii (1983) is used for the discretization of the flow field. The flow-field computation is done using the CRAY 1S computer at NASA Ames. The computed result is physically reasonable, even though no experimental data is available for the comparison purpose.
    Keywords: AERODYNAMICS
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 74
    facet.materialart.
    Unknown
    Reduction of wave drag by antisymmetric arrangement of wings and bodies. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The wave interference effects for bodies or wings in a mirror-symmetric arrangement, and in an antisymmetric arrangement are discussed. It is shown that while in the case of a mirror-symmetric arrangement large adverse interference effects can be observed, antisymmetric arrangements provide comparatively much smaller wave drags. The single continuous wing panels also adapt themselves more readily to varying angles of obliquity, and hence, to varying flight speeds. A detailed review is presented of the previous work on the aerodynamic properties and flight stability of oblique elliptic wing combinations. A possible mode of application of these combinations to transport aircraft operating at moderate supersonic speeds is suggested.
    Keywords: AERODYNAMICS
    Type: AIAA Journal; 10; Feb. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 75
    facet.materialart.
    Unknown
    Statistical distribution of spacecraft maximum structural response. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Under nonstationary random excitations resulting from booster engine shutdown, a direct statistical analysis of spacecraft maximum response is performed, and the spacecraft structural reliability is obtained. It is found that the Gumbel (1958) Type I asymptotic distribution of maximum values provides a reasonably good statistical model for spacecraft maximum responses. This approach makes it possible to perform the reliability-based optimum design of spacecraft structures.
    Keywords: SPACE VEHICLES
    Type: Journal of Spacecraft and Rockets; 9; Jan. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 76
    facet.materialart.
    Unknown
    Impact probe displacement in a supersonic turbulent boundary layer. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The experiment was performed on the test section sidewall in a supersonic pressure tunnel. The boundary layer at the test station was surveyed in turn by each of 8 impact probes ranging in size from about 1.3 to 48 mm. The impact pressures measured by these probes were combined with the test section static pressure to calculate Mach numbers. Probe displacement effects were evaluated in terms of these Mach number values.
    Keywords: AERODYNAMICS
    Type: AIAA Journal; 10; Apr. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 77
    facet.materialart.
    Unknown
    Effects of transverse outflow from a hypersonic separated region. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Features of hypersonic, finite-span separated flows with a turbulent boundary layer have been studied to provide a partial assessment of transverse outflow effects on separated flowfield characteristics. Results demonstrate the critical importance of transverse outflow in determining some of the characteristic features of a turbulent, separated boundary layer.
    Keywords: AERODYNAMICS
    Type: AIAA Journal; 10; Apr. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 78
    facet.materialart.
    Unknown
    Thermal design verification testing for the ATS-F and -G spacecraft. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: There is a wide fluctuation in the internal power dissipation from the components within the earth viewing module (EVM). The electronic component functional reliability required for a two-to-five year mission is the most significant factor for the thermal design criteria. A mathematical thermal model of the EVM and the orbital environment is used to predict the performance of the thermal control system. Comparisons of the results obtained in chamber thermal balance tests with the data computed on the basis of the theoretical model provide the means for validating the thermal design.
    Keywords: SPACE VEHICLES
    Type: Journal of Environmental Sciences; 15; Mar
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 79
    facet.materialart.
    Unknown
    The space shuttle and its uses. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The development of reusable space-shuttle vehicles has been made practical by the availability of improved staged-combustion engines and durable thermal protection systems. A two-state launch configuration with fully reusable booster and orbiter elements is considered to be the best design solution, and size specifications for such a vehicle are examined as a function of launch costs. Significant vehicle characteristics are explained in terms of cargo bay dimensions, cross-range maneuvering capability, mission duration requirements, engine characteristics, and acceleration constraints. Shuttle flight activities include satellite deployment and repair, sortie missions for short-duration research purposes, and space station support operations. Phases of the development program are outlined, and structural details of several candidate space shuttle concepts are illustrated.
    Keywords: SPACE VEHICLES
    Type: Aeronautical Journal; 76; Jan. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 80
    facet.materialart.
    Unknown
    Shuttle ascent guidance and control. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The requirements of a unified optimal guidance scheme are discussed, giving attention to a general formulation, aspects of self-targeting, problems of optimum guidance within the atmosphere, and a unified concept for all flight phases. Since no previous guidance scheme meets these requirements, the shuttle demands a fundamentally new approach. A new unified optimal guidance scheme, called Mascot, was developed. The capabilities of Mascot include the real-time solution of general trajectory-optimization problems and the unification of guidance for all flight phases.
    Keywords: SPACE VEHICLES
    Type: Astronautics and Aeronautics; 10; Feb. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 81
    facet.materialart.
    Unknown
    Flying automated laboratories to the planets. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Review of results obtained by instrumented spacecraft in investigation of the planets, mainly Mars. It appears that Mars is a world of varying topographical structure, some of which must have been created by the same processes that sculptured the moon and by others thus far unique in the solar system. The atmosphere is too thin to shield the surface, and there are no traces of liquid water. The very large recent dust storm is discussed. Mariner 9 has revealed definite indication of probable volcanic activity on Mars in recent geologic times.-
    Keywords: SPACE VEHICLES
    Type: Teledyne Ryan Aeronautical Reporter; 33; Spring 1
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 82
    facet.materialart.
    Unknown
    Turbulent-wake calculations with an eddy-viscosity model. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: A simple eddy-viscosity model is shown to make it possible to calculate numerically the mean properties of a turbulent wake. Although the structure of the Reynolds stress terms is not resolved, the results obtained are adequate for predicting velocity profiles and displacement thicknesses.
    Keywords: AERODYNAMICS
    Type: AIAA Journal; 10; Feb. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 83
    facet.materialart.
    Unknown
    Skylab status report. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The laboratory will be launched on Apr. 30, 1973, aboard a Saturn V vehicle. Approximately twenty-three and a half hours later the first crew will be launched in a command and service module aboard a Saturn IB launch vehicle. The laboratory will consist of modules. The orbital workshop (OWS) is made from the liquid oxygen and liquid hydrogen tanks of a Saturn S-IVB third stage. The OWS contains the living quarters and two experiments areas. The airlock sits on top of the OWS and contains the controls and hatch for the extra-vehicular activity.
    Keywords: SPACE VEHICLES
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 84
    facet.materialart.
    Unknown
    Small-scale wind shear definition for aerospace vehicle design. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Rawinsonde wind profile data provide adequate wind shear information for vertical height intervals greater than 1 km. To specify wind shears for intervals below 1 km for space vehicle design, detailed wind-profile information like that provided by the FPS-16 Radar/Jimsphere system or an extrapolation procedure is required. This paper is concerned with the latter alternative. It is assumed that any realization from an ensemble of wind profiles can be represented in terms of a Fourier integral. This permits the calculation of the ensemble standard deviation and mean of the corresponding shear ensemble for any altitude and shear interval in terms of the power spectrum of the ensemble of wind profiles. The results of these calculations show that the mean and standard deviation of the wind shear ensemble, as well as the wind shear for any percentile, asymptotically behave like the vertical interval to the 0.7 power. This result is in excellent agreement with shear data from Cape Kennedy, Fla.
    Keywords: SPACE VEHICLES
    Type: Journal of Spacecraft and Rockets; 9; Feb. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 85
    facet.materialart.
    Unknown
    Shock-wave, turbulent boundary-layer interaction on a blunted compression surface. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The application of Rose's (1970) analytical method to the study of a shock wave interacting with a turbulent layer on a blunted compression surface is described. Only those details of the method that specifically apply to the case under consideration are discussed.
    Keywords: AERODYNAMICS
    Type: Journal of Spacecraft and Rockets; 9; Apr. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 86
    facet.materialart.
    Unknown
    Shuttle status report. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: The Space Shuttle Program is still in Phase B, a phase consisting predominantly of paper analyses and trade studies leading to the selection of a single design. A brief history of the program up to Phase B is discussed together with the results of the original year-long Phase B effort, and the objectives of the Phase B extension currently in work. A Lockheed study is discussed together with a Grumman/Boeing study, Phase B contractor results, displays and controls, simulations, and the flight test.
    Keywords: SPACE VEHICLES
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 87
    facet.materialart.
    Unknown
    Nonlinear aerodynamic effects on bodies in supersonic flow (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Keywords: AERODYNAMICS
    Type: Journal of Aircraft (ISSN 0021-8669); 21; 809-815
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 88
    facet.materialart.
    Unknown
    New implicit boundary procedures - Theory and applications (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Description: Previously cited in issue 5, p. 579, Accession no. A83-16536
    Keywords: AERODYNAMICS
    Type: AIAA Journal (ISSN 0001-1452); 22; 1094-110
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 89
    facet.materialart.
    Unknown
    Numerical simulations of unsteady transonic flow in diffusers (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Description: Previously cited in issue 15, p. 2346, Accession no. A82-31959
    Keywords: AERODYNAMICS
    Type: AIAA Journal (ISSN 0001-1452); 22; 1139-114
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 90
    facet.materialart.
    Unknown
    Effects of viscosity on transonic-aerodynamic and aeroelastic characteristics of oscillating airfoils (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Keywords: AERODYNAMICS
    Type: Journal of Aircraft (ISSN 0021-8669); 21; 700-707
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 91
    facet.materialart.
    Unknown
    Leeside flows over delta wings at supersonic speeds (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Keywords: AERODYNAMICS
    Type: Journal of Aircraft (ISSN 0021-8669); 21; 680-686
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 92
    facet.materialart.
    Unknown
    Fresh attack on laminar flow (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Description: Laminar flow control is a technology with great potential for aircraft drag reduction. Stabilization of laminar boundary layers became known as natural laminar flow (NLF) and research led to the development of NLF airfoils. Research was also conducted on stabilization by suction, referred to as laminar flow control (LFC). Experiments demonstrated that extensive laminar flow could be achieved in flight. However, there remained doubts regarding the practicality of producing, with the technology then available, wing surfaces sufficiently smooth and wavefree to meet laminar-flow criteria and maintaining the wing surface quality in normal service. In 1976, the Aircraft Energy Efficiency (ACEE) program was begun by NASA to develop fuel-conservative technology for commercial transports. The progress of the ACEE program is discussed. Attention is given to LFC wing structures, and LFC leading-edge systems.
    Keywords: AERODYNAMICS
    Type: Aerospace America (ISSN 0740-722X); 22; 72-76
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 93
    facet.materialart.
    Unknown
    Space Shuttle heating analysis with variation in angle of attack and catalycity (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-18
    Description: Previously cited in issue 5, p. 586, Accession no. A83-16747
    Keywords: AERODYNAMICS
    Type: Journal of Spacecraft and Rockets (ISSN 0022-4560); 21; 217-219
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 94
    facet.materialart.
    Unknown
    Metric-discontinuous zonal grid calculations using the Osher scheme (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-19
    Description: Computations on zonal grids - in particular, grids with metric discontinuities resulting from the interspersion of highly clustered regions with coarse regions - are possible using a fully conservative form of the Osher upwind scheme. These zonal grids can result from an abrupt clustering of points near solution discontinuities or near other flow features that require improved resolution. The zonal approach is shown to capture shocks with almost 'shock-fitting' quality but with minimal effort. Results for inviscid flow, including quasi-one-dimensional nozzle flow, supersonic flow over a cylinder, and blast-wave diffraction by a ramp, are presented. These calculations demonstrate the powerful capabilities of the Osher scheme used in conjunction with zonal grids in simulating flow fields with complex shock patterns.
    Keywords: AERODYNAMICS
    Type: Computers and Fluids (ISSN 0045-7930); 12; 3, 19
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 95
    facet.materialart.
    Unknown
    Lifting surface theory for a helicopter rotor in forward flight (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-19
    Description: A lifting surface theory was developed for a helicopter rotor in forward flight for compressible and incompressible flow. The method utilizes the concept of the linearized acceleration potential and makes use of the vortex lattice procedure. Calculations demonstrating the application of the method are given in terms of the lift distribution on a single rotor, a two-bladed rotor, and a rotor with swept-forward and swept-back tips. In addition, the lift on a rotor which is vibrating in a pitching mode at 4/rev is given. Compressibility effects and interference effects for a two-bladed rotor are discussed.
    Keywords: AERODYNAMICS
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 96
    facet.materialart.
    Unknown
    Analysis of surface pressure distributions on two elliptic missile bodies (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-19
    Keywords: AERODYNAMICS
    Type: Journal of Spacecraft and Rockets (ISSN 0022-4650); 21; 528-533
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 97
    facet.materialart.
    Unknown
    A general perturbation approach for computational fluid dynamics (1984)
    In:  Other Sources
    Details
    Publication Date: 2011-08-19
    Keywords: AERODYNAMICS
    Type: AIAA Journal (ISSN 0001-1452); 22; 1748-175
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 98
    facet.materialart.
    Unknown
    Matrix transformations for spacecraft attitude determination. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Keywords: SPACE VEHICLES
    Type: Planetary and Space Science; 20; Oct. 197
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 99
    facet.materialart.
    Unknown
    Measurements of skin friction on the wall of a hypersonic nozzle. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Direct skin friction measurements obtained on the wall of a Mach 19.8 nozzle are presented. These measurements of skin friction and values deduced from the profile data are compared with predictions from a finite difference theory and also with several 'flat-plate' prediction methods for skin friction.
    Keywords: AERODYNAMICS
    Type: AIAA Journal; 10; Sept
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
  • 100
    facet.materialart.
    Unknown
    Taylor instability in the shock layer on a Jovian atmosphere entry probe. (1972)
    In:  Other Sources
    Details
    Publication Date: 2011-08-16
    Description: Investigation of the Taylor instability relative to the dynamical instability whose presence in the shock layer on a spacecraft entering the Jovian atmosphere is to be expected because of the difference in velocity across the shear layer. Presented calculations show that the Taylor instability at the interface between shock-heated freestream gas and ablation products is inconsequential in comparison to the shear layer instability.
    Keywords: AERODYNAMICS
    Type: Journal of Spacecraft and Rockets; 9; Sept
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    NASA TECHNICAL REPORTS
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...