ALBERT

Description: The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Description: The damping in roll and rolling effectiveness of two models of a missile having cruciform, triangular, interdigitated wings and tails have been determined through a Mach number range of 0.8 to 1.8 by utilizing rocket-propelled test vehicles. Results indicate that the damping in roll was relatively constant over the Mach umber range investigated. The rolling effectiveness was essentially constant at low supersonic speeds and increased with increasing mach numbers in excess of 1.4 over the Mach number range investigated. Aeroelastic effects increase the rolling-effectiveness parameters pb/2V divided by delta and decrease both the rolling-moment coefficient due to wing deflection and the damping-in-roll coefficient.

Description: By use of an approximate equation for the wave drag of slender bodies of revolution in a supersonic flow field, the optimum shapes of certain boattail bodies are determined for minimum wave drag. The properties of three specific families of bodies are determined, the first family consisting of bodies having a given length and base area and a contour passing through a prescribed point between the nose and base, the second family having fixed length, base area, and maximum area, and the third family having given length, volume, and base area. The method presented is easily generalized to determine minimum-wave-drag profile shapes which have contours that must pass through any prescribed number of points. According to linearized theory, the optimum profiles are found to have infinite slope at the nose but zero radius of curvature so that the bodies appear to have pointed noses, a zero slope at the body base, and no variation of wave drag with Mach number. For those bodies having a specified intermediate.diameter (that is, location and magnitude given), the maximum body diameter is shown to be larger, in general, than the specified diameter. It is also shown that, for bodies having a specified maximum diameter, the location of the maximum diameter is not arbitrary but is determined from the ratio of base diameter to maximum diameter.

Description: Buffet boundaries, buffeting-load increments for the stabilizers and elevators, and buffeting bending-moment increments for the stabilizers and wings as measured in gradual maneuvers for a jet-powered bomber airplane are presented. The buffeting-load increments were determined from strain-gage measurements at the roots or hinge supports of the various surfaces considered. The Mach numbers of the tests ranged from 0.19 to 0.78 at altitudes close to 30,000 feet. The predominant buffet frequencies were close to the natural frequencies of the structural components. The buffeting-load data, when extrapolated to low-altitude conditions, indicated loads on the elevators and stabilizers near the design limit loads. When the airplane was held in buffeting, the load increments were larger than when recovery was made immediately.

Description: A tank investigation has been conducted on a 1/8-size powered dynamic model of the Grumman JRF-5 airplane equipped with twin hydro-skis. The results of tests using two types of skis are presented: one had vertical sides joining the top surface to the chine; the other had the top surface faired to the chine to eliminate the vertical sides. Both configurations had satisfactory longitudinal stability although the model had a slightly greater stable elevator range available when the skis without the vertical sides were attached. Free model tests indicated no instability present when one ski emerged before the other. Considerable excess thrust was available at all speeds with either type of skis. A hump gross load-resistance ratio of 3.37 was obtained with the skis with the vertical sides and 3.53 with the other skis. Landing behavior in smooth water with yaw up to 15deg and roll up to 15deg in opposite directions was satisfactory with either type of skis.

Description: A flight investigation has been made to determine the external drag and pressure recovery of a 1/8.25 - scale flight model of the Consolidated Vultee XF-92 from Mach numbers 0.7 to 1.4 and Reynolds numbers from 8.5 x 10(exp 6) to 19.2 x 10(exp 6) at or near zero lift. Relative mass flow, average pressure recovery, total drag, internal drag, and external drag are presented as functions of Mach number. Between Mach numbers of 0.90 and 0.975, the external drag of the configuration (including base drag of the inner body and additive drag) was about equal to that of a similar model with a faired nose and no mass flow; however, at supersonic speeds the drag coefficient for the faired-nose model remained relatively constant whereas the drag coefficient for the ducted model continued to increase sharply. The internal drag coefficient of the duct was roughly constant at 0.013 up to a Mach number of 1.20; after which it decreased to 0.0075 at a Mach number of 1.4. The over-all pressure recovery of the inlet and duct varied from 94 percent at a Mach number of 0.7 to about 91 percent at a Mach number of 1.4 at a relative-mass-flow ratio of about 0.30. The losses in pressure recovery were believed to be caused by the possible occurrence of separation of flow from the inner body and by an aerodynamically unclean internal configuration which did not duplicate the form proposed for the original XF-92 airplane.

Description: An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Douglas XF4D-1 airplane has been made in the Langley free-flight tunnel. The model was flown with leading-edge slats retracted and extended over a lift-coefficient range from 0.5 to the stall. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls. The longitudinal stability and control characteristics of the model were satisfactory for all conditions investigated except near the stall with slats extended, where the model had a slight nosing-up tendency. The lateral stability and control characteristics of the model were considered satisfactory for all conditions investigated except near the stall with slats retracted, where a change in sign of the static- directional-stability parameter Cn(sub beta) caused the model to be directionally divergent. The addition of an extension to the top of the vertical tail did not increase Cn(sub beta) enough to eliminate the directional divergence of the model, but a large increase in Cn(sub beta) that was obtainable by artificial means appeared to eliminate the divergence and flights near the stall could be made. Artificially increasing the stability derivative-Cn(sub r) (yawing moment due to yawing) and Cn(sub p) (yawing moment due to rolling) had little effect on the divergence for the range of these parameters investigated. Calculations indicate that the damping of the lateral oscillation of the airplane with slats retracted or extended will be satisfactory at sea level but will be only marginally satisfactory at 40,000 feet.

Description: An investigation of a 1/24- scale dynamically similar model of the Douglas C-124 airplane was made to determine the ditching characteristics and proper technique for ditching the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion- picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded on the basis of results from model tests with scale-strength bottoms (equivalent to 1150 pounds per square foot, full scale) that the airplane should be ditched at a medium nose-high landing attitude (near 7deg) with flaps full down. The airplane will probably make a smooth run with considerable damage resulting to the fuselage bottom just forward of the wing, but it is not likely that the water inflow will be overwhelming to personnel provided they are not in the belly compartment. Longitudinal decelerations in calm water will be about 2 1/2g and the landing run will be about four fuselage lengths.

Description: A flight investigation has been made to determine the drag and longitudinal stability of a 1/10- scale model of the Douglas XF4D-1 airplane from Mach numbers 0.7 to 1.4 at lift coefficients near zero. The drag rise occurred near M = 0.95. The external drag coefficient was a constant value of about 0.012 at subsonic speeds up to the point of drag rise where it increased abruptly to a value of 0.030 at M = 1.0 followed by a more gradual increase to a value of 0.038 at M = 1.25. The model indicated that, at 35,000 feet and a level-flight free-stream Mach number of 1.0, the drag of the full-scale airplane would exceed the thrust available from an XJ40-WE-8 engine with after-burning. The transonic trim change was small. The aerodynamic center moved gradually from the most forward location of 21.0-percent mean aerodynamic chord at M = 0.9 to the most rearward location of 40-percent mean aerodynamic chord at M = 1.25. The damping in pitch was low.

Description: Two theoretical procedures are developed for designing asymmetric supersonic nozzles for which the calculated exit flow is nearly uniform over a range of Mach numbers. One procedure is applicable at Mach numbers less than approximately 3. This approach yields, without iteration, a nozzle for which the calculated exit flow is uniform at two Mach numbers and, with proper design, is nearly uniform at Mach numbers between, slightly above, and slightly below these two. The use of an inclined and curved sonic line is an essential feature of this approach, The second procedure requires iteration and is used far designs at Mach numbers exceeding 3. Although it is not a necessary feature, an inclined and curved sonic line is also used in this procedure. In both approaches the flow field dawn stream of the sonic line is determined using the method of characteristics.

Description: A flight investigation of a 1/7-scale rocket-powered model of the XF10F Grumman XFl0F airplane in the swept-wing configuration has been made. The purpose of this test was to determine the static longitudinal stability, damping in pitch, and longitudinal control effectiveness of the airplane with the center of gravity at 20 percent of the wing mean aerodynamic chord. Only a small amount of data was obtained from the test because, immediately after booster separation at a Mach number of 0.88, the configuration was directionally unstable and diverged in sideslip. Simultaneous with the sideslip divergence, the model became longitudinally unstable at 3 degree angle of attack and -6 degree sideslip and diverged in pitch to a high angle of attack. During the pitch-up the free-floating horizontal tail became unstable at 5 degree angle of attack and the tail drifted against its positive deflection limit.

Description: A tank investigation has been conducted of a 1/10-size powered-dynamic model of the Edo model 142 hydra-ski research airplane. The results of tests of two configurations are presented: One included a large ski and a ski well; the other, a small ski without a well. Water take-offs would be possible with the available thrust for either configuration: however, the configuration with the large ski emerged sooner and had less resistance from ski emergence until take-off. Longitudinal stability and landing behavior in smooth water were satisfactory for both configurations. Some alteration to the design of the tail would be desirable in order to reduce the spray loads.

Description: It has been shown that the circumferential pressure distributions for the inclined body and circular cylinder deviate from their respective theoretical inviscid distributions on the lee or downstream side in the same manner. With the aid of visual flow techniques, it has been shown that there is a shedding of vortices within the crossflow field of the inclined body. It has also been found that the vortex configuration depoends to a large extent on the shape of the nose of the body. To illustrate this, vapor screen pictures were made and results are discussed.

Description: The present paper presents the results of a brief investigation made to determine the effectiveness of a proposed emergency spin-recovery device to be used during demonstration spins of the Northrop XF -89 airplane. The proposed device makes use of split-type ailerons deflected +/-60deg on the outboard wing (left wing in a right spin). Tests made on a model which represented the airplane to a scale of 7 indicated that, if an uncontrollable spin is obtained in the design gross--weight loading, the device is not sufficiently effective to insure recovery,

Description: As part of a study of means of airspeed measurement at transonic speeds the use of static orifices located ahead of the wing tip has been investigated for possible application to service or research airspeed installations. The local static pressure and local Mach number have been measured at a distance of 1 tip chord ahead of the wing tip of a model of a swept-wing fighter airplane at true Mach numbers between 0.7 and 1.08 by the NACA wing-flow method. All measurements were made at or near zero lift. The local Mach number was found to be essentially equal to the true Mach numbers less than about 0.90. The local Mach number was found to be about 0.97 at a true Mach number of 0.95, and to be about 1.04 at a true Mach number of 1.08. The local Mach number provided a reasonable sensitive measure of true Mach number except for a restricted region near a true Mach number of 1.0 where the local Mach number did not change appreciably with true Mach number. The linear theory was found to predict qualitatively the effect of the fuselage on the static pressure ahead of the wing time but gave a reasonable prediction of the effect of the wing on the static pressure only at Mach numbers below 0.95.