ALBERT

Description: The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Description: A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions. The differences in drag can be eliminated for the design Mach number. Experimental results confirm the results of the theoretical analysis and show that pressure recoveries of 95 percent for Mach numbers of 1.33 and 1.52, 92 percent for a Mach number of 1.72, and 86 percent for a Mach number of 2.10 are possible, with the configurations considered. If the mass flow decreases, the total drag coefficient increases gradually and the pressure recovery does not change appreciably. The results of this work were first presented in a classified document issued in 1946.

Description: The performance of NACA 65-series compressor blade section in cascade has been investigated systematically in a low-speed cascade tunnel. Porous test-section side walls and for high-pressure-rise conditions, porous flexible end walls were employed to establish conditions closely simulating two-dimensional flow. Blade sections of design lift coefficients from 0 to 2.7 were tested over the usable angle-of-attack range for various combinations of inlet-flow angle. A sufficient number of combinations were tested to permit interpolation and extrapolation of the data to all conditions within the usual range of application. The results of this investigation indicate a continuous variation of blade-section performance as the major cascade parameters, blade camber, inlet angle, and solidity were varied over the test range. Summary curves of the results have been prepared to enable compressor designers to select the proper blade camber and angle of attack when the compressor velocity diagram and desired solidity have been determined.

Description: An investigation has been conducted in the Langley 20-foot free spinning tunnel to study the relative behavior in descent of a number of homogeneous balsa bodies of revolution simulating anti-personnel bombs with a small cylindrical exploding device suspended approximately 10 feet below the bomb. The bodies of revolution included hemispherical, near-hemispherical, and near-paraboloid shapes. The ordinates of one near-paraboloid shape were specified by the Office of the Chief of Ordnance, U. S. Army. The behavior of the various bodies without the cylinder was also investigated. The results of the investigation indicated that several of the bodies descended vertically with their longitudinal axis, suspension line, and small cylinder in a vertical attitude,. However, the body, the ordinates of which had been specified by the Office of the Chief of Ordnance, U. S. Army, oscillated considerably from a vertical attitude while descending and therefore appeared unsuitable for its intended use. The behavior of this body became satisfactory when its center of gravity was moved well forward from its original position. In general, the results indicated that the descent characteristics of the bodies of revolution become more favorable as their shapes approached that of a hemisphere.

Description: The damping in roll and rolling effectiveness of two models of a missile having cruciform, triangular, interdigitated wings and tails have been determined through a Mach number range of 0.8 to 1.8 by utilizing rocket-propelled test vehicles. Results indicate that the damping in roll was relatively constant over the Mach umber range investigated. The rolling effectiveness was essentially constant at low supersonic speeds and increased with increasing mach numbers in excess of 1.4 over the Mach number range investigated. Aeroelastic effects increase the rolling-effectiveness parameters pb/2V divided by delta and decrease both the rolling-moment coefficient due to wing deflection and the damping-in-roll coefficient.

Description: The subject of this paper is the drag of the nose section of bodies of revolution at zero angle of attack. The magnitude of the nose drag in relation to the total drag is very distinctly a function of the body design and the Mach number. It can range from a very small fraction of the total drag of the order of 10 percent to a very large fraction as high as 80 percent. The natural objective of nose design is to minimize the drag, but this objective is not always the primary one. Sometimes other factors overshadow the desire for minimum drag. The most conspicuous example of this is the proposal of guidance engineers that large-diameter spheres and other very blunt shapes be used at the nose tip. This paper will attempt to discuss both phases of the problem, noses for minimum drag and noses with very blunt tips. The state of the theory will also be reviewed and recent theoretical developments described, since the theory still remains a very valuable tool for assaying the effects of compromises in design and departure from shapes for which experimental data are available.

Description: A tank investigation has been conducted on a 1/8-size powered dynamic model of the Grumman JRF-5 airplane equipped with twin hydro-skis. The results of tests using two types of skis are presented: one had vertical sides joining the top surface to the chine; the other had the top surface faired to the chine to eliminate the vertical sides. Both configurations had satisfactory longitudinal stability although the model had a slightly greater stable elevator range available when the skis without the vertical sides were attached. Free model tests indicated no instability present when one ski emerged before the other. Considerable excess thrust was available at all speeds with either type of skis. A hump gross load-resistance ratio of 3.37 was obtained with the skis with the vertical sides and 3.53 with the other skis. Landing behavior in smooth water with yaw up to 15deg and roll up to 15deg in opposite directions was satisfactory with either type of skis.

Description: A wind-tunnel investigation of a 0.049-scale model of the Boeing XB-52 airplane was made at Mach numbers from 0.30 to 0.925 and at corresponding Reynolds numbers from about 2.3 x 10(exp 6) to 4.3 x 10(exp 6). The results of the investigation indicate satisfactory static longitudinal stability throughout the test Mach-number range and some loss in tail effectiveness beginning at about 0.80 Mach number. A comparison of the results of these tests with those of the same model in the Boeing Airplane Company's wind tunnel showed close agreement of lift- and drag-divergence Mach numbers. Slight differences were observed in tail effectiveness and the position of the stick-fixed neutral point.

Description: A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/30 -scale model of the Grumman XFlOF-1 airplane to determine what effect full-span slats would have on the spin-recovery characteristics of the swept-wing version of the XFlOF-1 airplane, which had previously been indicated as possessing undesirable spin-recovery characteristics without slats. The effects of extended nose-wheel doors and of fairing the air-duct inlets were also determined. The results indicated that, with slats fully extended, satisfactory recovery could be obtained by rudder reversal provided it was accompanied by movement of the trimmer ailerons to full with the spin (only up-going spoiler operative), Extension of the nose-wheel doors or fairing of the air-duct inlets did not improve the recovery characteristics.

Description: The damping-in-Toll stability derivatives of a missile configuration and its components were determined both experimentally and theoretically. The tests were conducted at a Mach number of 1.52 and at a Reynolds number, based on the mean aerodynamic chord of the wing, of 0.82 x 10(exp 6). The experimental damping derivative of the wing-body combination was 67 percent of the theoretical value. The difference is believed to have resulted mainly from the fact that the theory is not strictly applicable when the Mach number normal to the leading edge is almost unity, which was the case in the present investigation. For the tail-body combination the damping derivative was 86 percent of the theoretical value. In this case, the difference is believed to have been caused partially by mutual interference between the tail surfaces and partially by the low Reynolds number of the flow over the tail. It was found that the damping of the complete configuration was not equal to the sum of the damping derivatives of the components because of the effect of the wing downwash on the damping of the tail.

Description: A wing-body combination having a plane triangular wing of aspect ratio 2 with NACA 0005-63 thickness distribution in streamwise planes, and twisted and cambered for a trapezoidal span load distribution has been investigated at both subsonic and supersonic Mach numbers. The lift, drag, and pitching moment of the model are presented for Mach numbers from 0.60 to 0.90 and 1.30 to 1.70 at a Reynolds number of 3.0 million. The variations of the characteristics with Reynolds number are also shown for several Mach numbers.

Description: An investigation of a 1/24- scale dynamically similar model of the Douglas C-124 airplane was made to determine the ditching characteristics and proper technique for ditching the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion- picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded on the basis of results from model tests with scale-strength bottoms (equivalent to 1150 pounds per square foot, full scale) that the airplane should be ditched at a medium nose-high landing attitude (near 7deg) with flaps full down. The airplane will probably make a smooth run with considerable damage resulting to the fuselage bottom just forward of the wing, but it is not likely that the water inflow will be overwhelming to personnel provided they are not in the belly compartment. Longitudinal decelerations in calm water will be about 2 1/2g and the landing run will be about four fuselage lengths.

Description: An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

Description: Two theoretical procedures are developed for designing asymmetric supersonic nozzles for which the calculated exit flow is nearly uniform over a range of Mach numbers. One procedure is applicable at Mach numbers less than approximately 3. This approach yields, without iteration, a nozzle for which the calculated exit flow is uniform at two Mach numbers and, with proper design, is nearly uniform at Mach numbers between, slightly above, and slightly below these two. The use of an inclined and curved sonic line is an essential feature of this approach, The second procedure requires iteration and is used far designs at Mach numbers exceeding 3. Although it is not a necessary feature, an inclined and curved sonic line is also used in this procedure. In both approaches the flow field dawn stream of the sonic line is determined using the method of characteristics.

Description: A flight investigation was made at high subsonic, transonic, and supersonic speeds and at high Reynolds numbers to determine the zero-lift drag of a 1/10-scale model of the Northrop MX-775A missile and a scale model of the missile fuselage. The model of the complete configuration has a 45deg swept wing of aspect ratio 5.5 and a 33deg swept vertical fin. The body model was stabilized by three 45deg swept fins. The-drag-rise Mach number for the model of the complete configuration was approximately 0.96. The drag coefficient based on total wing area was 0.0330 at Mach number 1.39. The drag coefficient of the body model less fin drag was approximately 55 percent that of the complete model at the same Mach number. Addition of the wing to the fuselage apparently resulted in a favorable drag interference near Mach number 1.0.

Description: A flight investigation of a 1/7-scale rocket-powered model of the XF10F Grumman XFl0F airplane in the swept-wing configuration has been made. The purpose of this test was to determine the static longitudinal stability, damping in pitch, and longitudinal control effectiveness of the airplane with the center of gravity at 20 percent of the wing mean aerodynamic chord. Only a small amount of data was obtained from the test because, immediately after booster separation at a Mach number of 0.88, the configuration was directionally unstable and diverged in sideslip. Simultaneous with the sideslip divergence, the model became longitudinally unstable at 3 degree angle of attack and -6 degree sideslip and diverged in pitch to a high angle of attack. During the pitch-up the free-floating horizontal tail became unstable at 5 degree angle of attack and the tail drifted against its positive deflection limit.

Description: A tank investigation has been conducted of a 1/10-size powered-dynamic model of the Edo model 142 hydra-ski research airplane. The results of tests of two configurations are presented: One included a large ski and a ski well; the other, a small ski without a well. Water take-offs would be possible with the available thrust for either configuration: however, the configuration with the large ski emerged sooner and had less resistance from ski emergence until take-off. Longitudinal stability and landing behavior in smooth water were satisfactory for both configurations. Some alteration to the design of the tail would be desirable in order to reduce the spray loads.

Description: At present there is no satisfactory theory for calculating the pressure which acts at the blunt base of an object traveling at supersonic velocity. In fact, the essential mechanism determining the base pressure is only imperfectly understood. As a result, the existing knowledge of base pressure is based almost entirely on experiments. The main object of this paper is to summarize the principal results of the many wind tunnel and free flight measurements of base pressure on both bodies of revolution and blunt trailing edge airfoils. A relatively simple method of estimating base pressure is presented, and an indication is given as to how the characteristics of base pressure play an essential role in determining the shape of an aerodynamically efficient object for supersonic flight.

Description: It has been shown that the circumferential pressure distributions for the inclined body and circular cylinder deviate from their respective theoretical inviscid distributions on the lee or downstream side in the same manner. With the aid of visual flow techniques, it has been shown that there is a shedding of vortices within the crossflow field of the inclined body. It has also been found that the vortex configuration depoends to a large extent on the shape of the nose of the body. To illustrate this, vapor screen pictures were made and results are discussed.

Description: The three papers collected here are: 'The Effect of Nose Shape on the Drag of Bodies of Revolution at Zero Angle of Attack.', 'Base Pressure on Wings and Bodies with Turbulent Boundary Layers', and 'Flow over Inclined Bodies'. The subject of the first paper is the drag of the nose section of bodies of revolution at zero angle of attack. The main object of the second paper is to summarize the prinicpal results of the many wind tunnel and free flight measurements of base pressure on both bodies of revolution and blunt trailing edge airfoils.

Description: The present paper presents the results of a brief investigation made to determine the effectiveness of a proposed emergency spin-recovery device to be used during demonstration spins of the Northrop XF -89 airplane. The proposed device makes use of split-type ailerons deflected +/-60deg on the outboard wing (left wing in a right spin). Tests made on a model which represented the airplane to a scale of 7 indicated that, if an uncontrollable spin is obtained in the design gross--weight loading, the device is not sufficiently effective to insure recovery,

Description: As part of a study of means of airspeed measurement at transonic speeds the use of static orifices located ahead of the wing tip has been investigated for possible application to service or research airspeed installations. The local static pressure and local Mach number have been measured at a distance of 1 tip chord ahead of the wing tip of a model of a swept-wing fighter airplane at true Mach numbers between 0.7 and 1.08 by the NACA wing-flow method. All measurements were made at or near zero lift. The local Mach number was found to be essentially equal to the true Mach numbers less than about 0.90. The local Mach number was found to be about 0.97 at a true Mach number of 0.95, and to be about 1.04 at a true Mach number of 1.08. The local Mach number provided a reasonable sensitive measure of true Mach number except for a restricted region near a true Mach number of 1.0 where the local Mach number did not change appreciably with true Mach number. The linear theory was found to predict qualitatively the effect of the fuselage on the static pressure ahead of the wing time but gave a reasonable prediction of the effect of the wing on the static pressure only at Mach numbers below 0.95.

Description: The hypersonic similarity law as derived by Tsien has been investigated by comparing the pressure distributions along bodies of revolution at zero angle of attack. In making these comparisons, particular attention was given to determining the limits of Mach number and fineness ratio for which the similarity law applies. For the purpose of this investigation, pressure distributions determined by the method of characteristics for ogive cylinders for values of Mach numbers and fineness ratios varying from 1.5 to 12 were compared. Pressures on various cones and on cone cylinders were also compared in this study. The pressure distributions presented demonstrate that the hypersonic similarity law is applicable over a wider range of values of Mach numbers and fineness ratios than might be expected from the assumptions made in the derivation. This is significant since within the range of applicability of the law a single pressure distribution exists for all similarly shaped bodies for which the ratio of free-stream Mach number to fineness ratio is constant. Charts are presented for rapid determination of pressure distributions over ogive cylinders for any combination of Mach number and fineness ratio within defined limits.

Description: No abstract available

Description: The autorotative performance of an assumed helicopter was studied to determine the effect of inoperative jet units located at the rotor-blade tip on the helicopter rate of descent. For a representative ramjet design, the effect of the jet drag is to increase the minimum rate of descent of the helicopter from about 1,OO feet per minute to 3,700 feet per minute when the rotor is operating at a tip speed of approximately 600 feet per second. The effect is less if the rotor operates at lower tip speeds, but the rotor kinetic energy and the stall margin available for the landing maneuver are then reduced. Power-off rates of descent of pulse-jet helicopters would be expected to be less than those of ramjet. helicopters because pulse jets of current design appear to have greater ratios of net power-on thrust to power-off, drag than currently designed rain jets. Iii order to obtain greater accuracy in studies of autorotative performance, calculations in'volving high power-off rates of descent should include the weight-supporting effect of the fuselage parasite-drag force and the fact that the rotor thrust does not equal the weight of the helicopter.

Description: Free-flight tests have been made to determine the zero-lift drag of several configurations of the XAAM-N-2 pilotless aircraft. Base-pressure measurements were also obtained for some of the configurations. The results show that increasing the wing-thickness ratio from 4 to 6 percent increased the wing drag by about 100 percent at M = 1.3 and by about 30 percent at M = 1.8. Increasing the nose fineness ratio from 5.00 to 6.25 reduced the drag coefficient of the wingless models a maximum of about 0.030 (10 percent) at M = 2.0. A corresponding change in nose shape for the winged models decreased the drag coefficient by about 0.05 in the Mach number range from 1.1 to 1.4; at Mach numbers greater than 1.6 no measurable reduction in drag coefficient was obtained. The drag of the present Sparrow fuselage is less than that of a parabolic fuselage which could contain the same equipment.

Description: A flight test was made a t high subsonic, transonic, and supersonic speeds and at high Reynolds numbers to determine the zero-lift drag of a 1/14-scale model of the Northrop MX-775B pilotless aircraft with small small body. The triangular wing of the model had 67.5 deg leading-edge sweep and 15 deg. trailing-edge sweep, The wing airfoil sections were modified NACA 0004 sections. The drag coefficient based on total wing area was 0.0107 at Mach number 1.60. At transonic speeds the maximum drag coefficient was 0.0125. The force-break Mach number was 0,98.

Description: The study of the hydrodynamic properties of planing bottom of flying boats and seaplane floats is at the present time based exclusively on the curves of towing tests conducted in tanks. In order to provide a rational basis for the test procedure in tanks and practical design data, a theoretical study must be made of the flow at the step and relations derived that show not only qualitatively but quantitatively the inter-relations of the various factors involved. The general solution of the problem of the development of hydrodynamic forces during the motion of the seaplane float or flying boat is very difficult for it is necessary to give a three-dimensional solution, which does not always permit reducing the analysis to the form of workable computation formulas. On the other had, the problem is complicated by the fact that the object of the analysis is concerned with two fluid mediums, namely, air and water, which have a surface of density discontinuity between them. The theoretical and experimental investigations on the hydrodynamics of a ship cannot be completely carried over to the design of floats and flying-boat hulls, because of the difference in the shape of the contour lines of the bodies, and, because of the entirely different flow conditions from the hydrodynamic viewpoint.

Description: A wind-tunnel investigation has been conducted to determine the stability and control characteristics of a full-size model of the Hughes MX-904 missile. Aerodynamic characteristics of the complete model through moderate ranges of angles of attack and yaw, with an additional test made through an angle of attack of 180 degrees, are presented. The effects of horizontal tail deflection are also included.

Description: Force tests on a proposed body shape of the Hermes A-2 missile with and without longitudinal spoilers were made at Mach number 4.04. Values of normal force coefficient, pitching-moment coefficient, and center-of-pressure position were obtained.

Description: A ditching investigation of a model of the Convair-Liner airplane was made to observe the behavior and determine the safest procedure for making an emergency water landing. The ditching model was designed and constructed by the National Advisory Committee for Aeronautics. Design information on the airplane was furnished by the Consolidated Vultee Aircraft Corporation. A three-view drawing of the airplane is shown. The investigation was made in calm water at the Langley tank no. 2 monorail.

Description: An investigation has been made in the Langley gust tunnel with two identical airplane models approximating 1/40-scale models of the B-29, coupled in tandem with a boom so that the individual centers of gravity were equidistant from the single coupling joint at the tail of the lead airplane. Time histories of the boom joint load were obtained as the models were flown through a gust. The results indicate that on a similar configuration involving airplanes the size of B-29 airplanes a load on the boom joint of 10,000 to 14,000 pounds could be induced by encountering a gust of 50 feet per second and having a gradient distance of 17 chords, at a forward speed of 380 feet per second and that the total load is extremely sensitive to the steadiness of flight that can be maintained with or without a gust. It is felt that the results are probably satisfactory to show order of magnitude, but it does not appear possible that a precise determination of the joint load that would be applicable to the full-scale airplanes can be obtained by gust-tunnel tests.

Description: Flight tests have been conducted on rocket-propelled models of an airplane configuration incorporating a sweptback wing with inverse taper to investigate the drag, stability, and control characteristics at transonic and supersonic speeds. The models were tested with a conventional tail arrangement in the Mach number range from 0.55 to 1.2. In addition to the various aerodynamic parameters obtained, the flying qualities were computed for a full-scale airplane with the center-of-gravity location at 18 percent of the mean aerodynamic chord. Also, included in this investigation are drag measurements made on relatively simple fixed-control models tested with both conventional and V-tail arrangements.

Description: An experimental investigation of the variation of aileron rolling effectiveness and total drag with Mach number has been made using 1/6-scale rocket-propelled models of the Bell MX-776. Three models having constant-chordwise-thickness full-span aileron at approximate deflections of 2 deg, 5 deg, and 15 deg have been flown. Positive control effectiveness over the Mach number range between approximately 0.5 and 1.2 was obtained from the models and no indication of reversal of effectiveness was encountered. The ratio of tip helix angle to aileron deflection indicated a decrease in proportional rolling effectiveness with increasing deflections in the Mach number range from approximately 0.7 to 1.0. A drag rise of about 125 percent in the transonic region between Mach numbers of 0.85 and 1.02 followed by a gradual decrease at higher speeds was revealed.

Description: An investigation of a 1/24-scale dynamically similar model of the Boeing B-47 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. The airplane should be ditched at the lowest speed and highest attitude consistent with adequate control; the flaps should be full down. The airplane will probably make a deep but fairly smooth run. The fuselage bottom will be damaged and partially filled with water; consequently, crew members should be assigned ditching stations near an exit in the upper or forward part of the fuselage. The nacelles may be expected to be torn away from the wing. In calm water the maximum decelerations will be about 3g and the landing run will be about 6 fuselage lengths.

Description: At the request of the Air Materiel Command, an investigation was made in the Langley free-flight tunnel to determine the longitudinal stability and control characteristics of models coupled together in a tandem configuration for aerial refueling similar to one proposed by the Douglas Aircraft Company, Inc. Static force tests were made with 1/20-scale models of the B-29 and F-80 airplanes to determine the effects of rigidly coupling the airplanes together. The Douglas configuration differs from the rigid configuration tested in that it provides for some freedom in pitch and vertical displacement. The force tests showed that, for the bomber alone, the aerodynamic center was 0.21 mean aerodynamic chord behind the center of gravity (stable) but that for the tandem configuration with rigid coupling the aerodynamic center was 0.28 mean aerodynamic chord forward of the center of gravity of the combination (unstable). This reduction in stability was caused by the downwash of the bomber on the fighter. The pitching moment produced by elevator deflection of the bomber was reduced approximately 50 percent by addition of the fighter. Some recent flight tests made in the free-flight tunnel on models in a similar tandem configuration indicated that, with a hinged coupling permitting freedom in pitch, the stability of the combination was better than that obtained with a rigid coupling and was about the same as that for the bomber alone.

Description: At the request of the Air Materiel Command an investigation was made in the Langley free-flight tunnel to determine the static longitudinal stability and control characteristics of models coupled together in a tandem configuration proposed by All American Airways, Inc. Force tests were made using 1/20-scale models of B-29 end F-80 airplanes to determine the effects of coupling the fighter to the tail of the bomber. The results of the investigation showed that for the bomber alone the aerodynamic center was 0.21 mean aerodynamic chord behind the center of gravity (stable) but that for the tandem configuration the aerodynamic center was 0.09 mean aerodynamic chord forward of the center of gravity, of the combination (unstable). The elevator effectiveness of the bomber was reduced approximately 50 percent by addition of the fighter. Some recent flight tests made in the free-flight tunnel with models simulating the proposed configuration indicate that the reduction in stability may be minimized by incorporating a hinged coupling permitting freedom in pitch.

Description: An investigation was made by the NACA wing-flow method to determine the drag, pitching-moment, lift, and angle-of-attack characteristics at transonic speeds of various configurations of a semispan model of an early configuration of the XF7U-1 tailless airplane. The results of the tests indicated that for the basic configuration with undeflected ailavator, the zero-lift drag rise occurred at a Mach number of about 0.85 and that about a five-fold increase in drag occurred through the transonic speed range. The results of the tests also indicated that the drag increment produced by -8.0 degrees deflection of the ailavator increased with increase in normal-force coefficient and was smaller at speeds above than at speeds below the drag rise. The drag increment produced by 35 degree deflection of the speed brakes varied from 0.040 to 0.074 depending on the normal-force coefficient and Mach number. These values correspond to drag coefficients of about 0.40 and 0.75 based on speed-brake frontal area. Removal of the fin produced a small positive drag increment at a given normal-force coefficient at speeds during the drag rise. A large forward shift of the neutral-point location occurred at Mach numbers above about 0.90 upon removal of the fin, and also a considerable forward shift throughout the Mach number range occurred upon deflection of the speed brakes. Ailavator ineffectiveness or reversal at low deflections, similar to that determined in previous tests of the basic configuration of the model in the Mach number range from about 0.93 to 1.0, was found for the fin-off configuration and for the model equipped with skewed (more highly sweptback) hinge-line ailavators. With the speed brakes deflected, little or no loss in the incremental pitching moment produced by deflection of the ailavator from O degrees to -8.00 degrees occurred in the Mach number range from 0.85 to 1.0 in contrast to a considerable loss found in previous tests with the speed brakes off.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel to determine the spin and recovery characteristics of a 0.057-scale model of the modified Chance Vought XF7U-1 airplane. The primary change in the design from that previously tested was a revision of the twin vertical tails. Tests were also made to determine the effect of installation of external wing tanks. The results indicated that the revision in the vertical tails did not greatly alter the spin and recovery characteristics of the model and recovery by normal use of controls (fill rapid rudder reversal followed approximately one-half turn later by movement of the stick forward of neutral) was satisfactory. Adding the external wing tanks to cause the recovery characteristics to become critical and border on an unsatisfactory condition; however, it was shown that satisfactory recovery could be obtained by jettisoning the tanks, followed by normal recovery technique.

Description: A flight test was made to determine the servoplane effectiveness and stability characteristics of the free-floating horizontal stabilizer to be used on the XF10F airplane. The results of this test indicate that servoplane effectiveness is practically constant through the speed range up to a Mach number of 1.15, and the stabilizer static stability is satisfactory. A loss of damping occurs over a narrow Mach number range near M = 1.0, resulting in dynamic instability of the stabilizer in this narrow range. Above M = 1.0 there is a gradual positive trim change of the stabilizer.

Description: An investigation of the spin and recovery characteristics of a 1/24-scale model of the Grumman AF-2S, -2W airplane was conducted in the Langley 20-foot free-spinning tunnel. The effects of controls on the erect and inverted spin and recovery characteristics for a range of possible loadings of the.airplane were determined. The effect of a revised-tail installation (small dual fins added to the stabilizer of the original tail and the vertical-tail height of the original tail increased) and the effect of various ventral-fin and antispin-fillet installations were determined. The investigation also included spin-recovery parachute tests.

Description: An investigation has been made in the Langley 9- by 12-inch super-sonic blowdown tunnel at Mach numbers of 1.62 and 1.96 of a partial-span body with one tail surface, designed for use on the Hughes Falcon (MX-904) missile. The present paper extends the work reported in NACA-RM-SL50E10. Force and moment data including elevator hinge moment were obtained for the conditions of the tail in the presence of a small segment of the fore-shortened body, in the presence of a semi-span body and attached to a semi-span body, and for the condition of the foreshortened semi-span body alone.

Description: An investigation of the static and dynamic longitudinal stability characteristics of 1/3.7 scale rocket-powered model of the Bell MX-776A has been made for a Mach number range from 0.8 to 1.6. Two models were tested with all control surfaces at 0 degree deflection and centers of gravity located 1/4 and 1/2 body diameters, respectively, ahead of the equivalent design location. Both models were stable about the trim conditions but did not trim at 0 degree angle of attack because of slight constructional asymmetries. The results indicated that the variation of lift and pitching moment was not linear with angle of attack. Both lift-curve slope and pitching-moment-curve slope were of the smallest magnitude near 0 degree angle of attack. In general, an increase in angle of attack was accompanied by a rearward movement of the aerodynamic center as the rear wing moved out of the downwash from the forward surfaces. This characteristic was more pronounced in the transonic region. The dynamic stability in the form of total damping factor varied with normal-force coefficient but was greatest for both models at a Mach number of approximately 1.25. The damping factor was greater at the lower trim normal-force coefficients except at a Mach number of 1.0. At that speed the damping factor was of about the same magnitude for both models. The drag coefficient increased with trim normal-force coefficient and was largest in the transonic region.

Description: Investigations have been conducted to determine by means of total-pressure surveys the boundaries of single and twin jets discharging through convergent nozzles into quiescent air. The jet boundaries for the region from the nozzle outlets to a station 6 nozzle diameters downstream are presented for nozzle pressure ratios ranging from 2.5 t o 16.0 and for twin-Jet nozzle center-line spacings ranging from 1.42 to 2.50 nozzle diameters. The effects of these parameters on the interaction of twin Jets are discussed. In order to ascertain the utility of the results for other than the test conditions, the effects of jet temperature, Reynolds number, and humidity on the pressure boundaries have been briefly investigated. The result indicate that for a jet of 2.6 the pressure boundaries are slightly smaller than those of corresponding unheated jets and that the effects of Reynolds number and humidity are negligible.

Description: Calculations have been made to find range? attainable by bombers of gross weights from l40,000 to 300,000 pounds powered by turbine-propeller power plants. Only conventional configurations were considered and emphasis was placed upon using data for structural and aerodynamic characteristics which are typical of modern military airplanes. An effort was made to limit the various parameters invoked in the airplane configuration to practical values. Therefore, extremely high wing loadings, large amounts of sweepback, and very high aspect ratios have not been considered. Power-plant performance was based upon the performance of a typical turbine-propeller engine equipped with propellers designed to maintain high efficiencies at high-subsonic speeds. Results indicated, in general, that the greatest range, for a given gross weight, is obtained by airplanes of high wing loading, unless the higher cruising speeds associated with the high-wing-loading airplanes require-the use of thinner wing sections. Further results showed the effect of cruising at-high speeds, of operation at very high altitudes, and of carrying large bomb loads.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/30 - scale model of the Grumman XFlOF-1 airplane to determine its spin and recovery characteristics. The investigation included erect and inverted spins for both the straight-wing and swept-wing configurations. Tests to determine the optimum size spin-recovery parachutes and the rudder forces required for recovery were also made. The results indicated that in the straight-wing configuration, satisfactory recoveries of the airplane will be obtained from erect and inverted spins by rudder reversal alone. In the swept-wing configuration recoveries will be unsatisfactory from erect spins. Unsweeping the wings during the spin and reversal of the rudder, however, will lead to eventual recovery. The test results also indicated that, if existing small ailerons are made deflectable through large angles, satisfactory recoveries will be obtained from erect spins in the swept-wing configuration by simultaneous movement of the rudder to against the spin and movement of the ailerons to with the spin. Normal-size ailerons deflected through a normal range would also be effective. Satisfactory recoveries by rudder reversal will be obtained from inverted spins in the swept-wing configuration. In the straight-wing configuration a 14.2-foot tail parachute or a 5.0-foot wing-tip parachute opened on the outer wing tip will effect satisfactory recovery of the airplane by parachute action alone; a 30.0-foot tail parachute or a 10.0-foot wing-tip parachute will be required for the swept-wing configuration. The forces required to fully reverse the rudder should be within the capabilities of the pilot.

Description: Dynamic--response measurements for various conditions of displacement and rate signal input, sensitivity setting, and simulated hinge moment were made of the three control-surface servo systems of an NAES-equipped remote-controlled airplane while on the ground. The basic components of the servo systems are those of the General Electric Company type G-1 autopilot using electrical signal. sources, solenoid-operated valves, and hydraulic pistons. The test procedures and difficulties are discussed, Both frequency and transient-response data, are presented and comparisons are made. The constants describing the servo system, the undamped natural frequency, and the damping ratio, are determined by several methods. The response of the system with the addition of airframe rate signal is calculated. The transfer function of the elevator surface, linkage, and cable system is obtained. The agreement between various methods of measurement and calculation is considered very good. The data are complete enough and in such form that they may be used directly with the frequency-response data of an airplane to predict the stability of the autopilot-airplane combination.

Description: An investigation was conducted with a single combustor from a J47 turbojet engine using weathered aviation gasoline and several spark-plug modifications to determine altitude ignition, acceleration, and steady state operating characteristics. Satisfactory ignition was obtained with two modifications of the original opposite-polarity spark plug up to and including an altitude of 40,003 feet at conditions simulating equilibrium windmilling of the engine at a flight speed of 400 miles per hour. At a simulated altitude of 30,000 feet, satisfactory ignition was obtained over a range of simulated engine speeds. No significant effect of fuel temperature on ignition limits was observed over a range of fuel temperatures from 80 deg to -52 deg F. At an altitude of 30,000 feet, the excess temperature rise available for acceleration at low engine speeds was limited by the ability of the combustor to produce temperature rise, whereas at high engine speeds the maximum allowable turbine-inlet temperature became the restricting factor. Altitude operational limits increased from about 51,500 feet at 55 percent of rated engine speed to about 64,500 feet at 85 percent of rated speed. Combustion efficiencies varied from 59.0 to 92.6 percent over the range investigated and decreased with a decrease in engine speed and with an increase in altitude; higher efficiencies would have been obtained if lower altitudes had been investigated. Comparisons were made of the combustion efficiencies of weathered aviation gasoline and MIL-F-5616 fuel at altitudes of 30,000 and 40,000 feet. Combustion efficiencies obtained with MIL-F-5616 fuel were 8 percent higher at rated engine speed and 14 percent lower at 55 percent of rated speed than those obtained with weathered aviation gasoline.

Description: The behavior of the Westinghouse electronic power regulator operating on a J34-WE-32 turbojet engine was investigated in the NACA Lewis altitude wind tunnel at the request of the Bureau of Aeronautics, Department of the Navy. The object of the program was to determine the, steady-state stability and transient characteristics of the engine under control at various altitudes and ram pressure ratios, without afterburning. Recordings of the response of the following parameters to step changes in power lever position throughout the available operating range of the engine were obtained; ram pressure ratio, compressor-discharge pressure, exhaust-nozzle area, engine speed, turbine-outlet temperature, fuel-valve position, jet thrust, air flow, turbine-discharge pressure, fuel flow, throttle position, and boost-pump pressure. Representative preliminary data showing the actual time response of these variables are presented. These data are presented in the form of reproductions of oscillographic traces.

Description: A rocket-propelled model of the Mx-656 configuration has been flown through the Mach number range from 0.65 to 1.25. An analysis of the response of the model to rapid deflections of the horizontal tail gave information on the lift, drag, longitudinal stability and control, and longitudinal-trim change. The lift-coefficient range covered by the test was from -0.2 to 0,3 throughout most of the Mach number range, The model was statically and dynamically stable throughout the lift-coefficient and Mach number range of the test. At subsonic speeds the aerodynamic center moved f o m r d with increasing lift coefficient. The most forward position of the aerodynamic center was about 12,5 percent of the mean aerodynamic chord at a small positive lift coefficient and at a Mach number of about 0.84. A t supersonic speeds the aerodynamic center was well aft, varying from 33 to 39 percent of the mean aerodynamic chord at Mach numbers of 1.0 and 1.25, respectively. Transonic-trim change, as measured by the change in trim lift coefficient with Mach number at a constant t a i l setting, was of small magnitude (about 0.1 lift coefficient for zero tail setting). The zero-lift/drag coefficient increased about 0.042 in the region between a Mach number of 0.9 and 1.1

Description: After conclusion of the spin investigation of the model Me 210 with elongated fuselage and central vertical tail surfaces (model condition III; reference 3), tests were performed on the same model with a vee tail (model condition IV). Here the entire tail surfaces consist of only one surface with pronounced dihedral. Since the blanketing of the vertical tail surfaces by the horizontal tail surfaces, which may occur in case of standard tail surfaces, does not occur here, one could expect for this type of tail surface favorable spin characteristics, particularly with respect to rudder effectiveness for spin recovery. However, the test results did not confirm these expectations. The steady spin was shown to be very irregular; regarding rudder effectiveness the vee tail surfaces proved to be inferior even to standard tail surfaces, thus they represent the most unfavorable of the four fuselage and tail-surface combinations investigated so far.

Description: An investigate ion was made of the disturbed motion of a gas for the harmonic vibrations of a thin slightly cambered wing of finite span moving forward with supersonic velocity. This problem was considered by E. A. Krasilshchikova who applied the method of Fourier series and obtained a solution of the space problem for the condition that the Mach cones drawn through the leading edge of the wing intersect the wing or are tangent to it. In this paper, a different method of solution is given, which is free from the previously mentioned condition. In particular, the vibrations of a triangular wing lying within the Mach cone are considered.