ALBERT

Description: As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Description: The key measurement to acquire for understanding unsteady flow is surface pressure. Unsteady Pressure-Sensitive Paint (uPSP) is an emerging optical technique used in wind tunnel testing to measure fluctuating surface pressures. Recently, tests were conducted on NASAs Space Launch System in NASA Ames Research Centers Unitary Plan Wind Tunnel to determine the aeroacoustics environment and assist in developing the buffet forcing functions. Unsteady PSP data was collected during this test campaign. Steady state PSP data, infrared thermography, shadowgraph, accelerometer data, and dynamic pressure transducer data were also collected. In all 50 TB of data were collected during the three days of testing. During these three days of testing, a repeating transonic and supersonic alpha sweep condition was acquired. This paper presents these two wind tunnel conditions and examines how the temperature influences the PSP data. In the first large demonstration of uPSP in 2015 on an NESC-, AETC-sponsored wind tunnel test, lifetime PSP results highlighted the influence the model temperature had on the PSP data. A best practice of heat soaking the model before acquiring calibration images was followed during the test campaign presented in this paper. An infrared thermography camera and thermocouples were installed in the model to collect more details of the model surface temperature. Data processing schemes for uPSP are still in development but will be briefly presented here as well.

Description: As a result of the continued interest in designing efficient low Reynolds number systems, the University of Notre Dame decided to organize a Conference on Low Reynolds Number Aerodynamics in June 1989. This Conference followed the 1986 International Conference in London by about three years and the first Conference on Low Reynolds Number Airfoil Aerodynamics at Notre Dame in 1985 by four years. The emphasis of the 1989 Conference was to assess the state-of-the-art in the chord Reynolds number range from about 10,000 to about 700,000. Applications of current interest include high altitude remotely or robotically piloted vehicles, ultra-light, and human powered vehicles as well as mini-RPVs at low altitudes. Other examples include small axial-flow fans used to cool electronic equipment in the unpressurized sections of high-altitude aircraft and gas turbine blades. High Reynolds number airfoil design strategies attempt to control the onset and development of turbulent boundary layers. This is difficult at low Reynolds numbers because of the increased stability of attached laminar boundary layers. Therefore, laminar separation is common even at small angles of attack at low Reynolds numbers. Under these conditions, the development of a turbulent boundary layer usually depends on the formation of a transitional separation bubble. The purpose of this Conference on Low Reynolds Number Aerodynamics was to bring together those researchers who have been active in areas closely related to this subject. It is clear from the papers presented that a great deal of progress has been made in understanding the occurrence and behavior of laminar separation and transition as well as their overall effect on the performance of airfoils at low chord Reynolds numbers. This progress has brought us closer to our goal of improving analytical methods for the design and evaluation of a variety of practical applications.

Description: A balance ring (18) which is shrunk fit within each disk (12) of a rotor is selectively ground for detail balance. A plurality of openings (20) through the outer edge of the balance ring receive weights during the asssembly balance of the rotor. A snap ring (42) retains the weights within the openings.

Description: Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth-depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Description: Three-dimensional viscous flow computations are presented for the F/A-18 forebody-LEX geometry. Solutions are obtained from an algorithm for the compressible Navier-Stokes equations which incorporates an upwind-biased, flux-difference-splitting approach along with longitudinally-patched grids. Results are presented for both laminar and fully turbulent flow assumptions and include correlations with wind tunnel as well as flight-test results. A good quantitative agreement for the forebody surface pressure distribution is achieved between the turbulent computations and wind tunnel measurements at Mach number of 0.6. The computed turbulent surface flow patterns on the forebody qualitatively agree well with in-flight surface flow patterns obtained on an F/A-fS aircraft at Mach number of 0.34.

Description: Acoustic and aerodynamic research at NASA Lewis Research Center on advanced propellers is reviewed including analytical and experimental results on both single and counterrotation. Computational tools used to calculate the detailed flow and acoustic i e l d s a r e described along with wind tunnel tests to obtain data for code verification . Results from two kinds of experiments are reviewed: ( 1 ) performance and near field noise at cruise conditions as measured in the NASA Lewis 8-by 6-Foot Wind Tunnel and ( 2 ) farfield noise and performance for takeoff/approach conditions as measured in the NASA Lewis 9-by 15-Font Anechoic Wind Tunnel. Detailed measurements of steady blade surface pressures are described along with vortex flow phenomena at off design conditions . Near field noise at cruise is shown to level out or decrease as tip relative Mach number is increased beyond 1.15. Counterrotation interaction noise is shown to be a dominant source at take off but a secondary source at cruise. Effects of unequal rotor diameters and rotor-to-rotor spacing on interaction noise a real so illustrated. Comparisons of wind tunnel acoustic measurements to flight results are made. Finally, some future directions in advanced propeller research such as swirl recovery vanes, higher sweep, forward sweep, and ducted propellers are discussed.

Description: Acoustic data taken in the anechoic Deutsch-Niederlaendischer Windkanal (DNW) have documented the blade-vortex interaction (BVI) impulsive noise radiated from a 1/7-scale model main rotor of the AH-1 series helicopter. Averaged model-scale data were compared with averaged full-scale, in-flight acoustic data under similar non-dimensional test conditions using an improved data analysis technique. At low advance ratios (mu = 0.164 - 0.194), the BVI impulsive noise data scale remarkably well in level, waveform, and directivity patterns. At moderate advance ratios (mu = 0.224 - 0.270), the scaling deteriorates, suggesting that the model-scale rotor is not adequately simulating the full-scale BVI noise. Presently, no proved explanation of this discrepancy exists. Measured BVI noise radiation is highly sensitive to all of the four governing nondimensional parameters--hover tip Mach number, advance ratio, local inflow ratio, and thrust coefficient.

Description: The effect of rotor blade dynamics on aerodynamic and structural loads is examined for a conventional, main- rotor helicopter using both a comprehensive rotorcraft analysis (CAMRAD) and night test data. The impact of blade dynamics on blade section lift-coefficient time histories is studied by comparing predictions from both a rigid blade analysis and an elastic blade analysis with helicopter flight test data. The elastic blade analysis better predicts high-frequency behavior of section lift. In addition, components of the blade angle of attack, such as elastic blade twist, blade nap rate, blade slope velocity, and inflow, are examined as a function of blade mode. Elastic blade motion affects the blade angle of attack by a few tenths of a degree, and up to the sixth rotor harmonic. A similar study of the influence of blade dynamics on bending and torsion moments was also conducted. The modal analysis of the predicted blade structural loads suggested that five elastic bending deg of freedom (four flap and one lag) and three elastic torsion deg of freedom contributed to calculations of the blade structural loads. However, when structural bending load predictions from several elastic blade analyses were compared with flight test data, an elastic blade model consisting of only three elastic bending modes (first and second flap, and first lag), and two elastic torsion modes was found to be sufficient for maximum correlation.

Description: Helicopter rotor aerodynamics is basically the study of unsteady aerodynamic flows in a rotating and translating coordinate system. Current trends in this field are briefly reviewed by examining recent advances in lifting-surface theory, wake modeling, panel methods, and finite-difference models' Examples are used to illustrate selected current methods and some indications of promising future directions are highlighted.

Description: A wind-tunnel investigation was conducted in which aerodynamic loads were measured on a small-scale helicopter rotor and a body of revolution located close to it as an idealized model of a fuselage. The objective was to study the aerodynamic interactions as a function of forward speed, rotor thrust, and rotor/body position. Results show that body loads, normalized by rotor thrust, are functions of the ratio between free-stream velocity and the hover-induced velocity predicted by momentum theory.

Description: The visualization of laminar to turbulent boundary layer transition plays an important role in flight and wind tunnel aerodynamic testing of aircraft wing and body surfaces. Visualization can help provide a more complete understanding of both transition location as well as transition modes; without visualization, the transition process can be very difficult to understand. In the past, the most valuable transition visualization methods for fight applications included sublimating chemicals and oil flows. Each method has advantages and limitations. In particular, sublimating chemicals are impractical to use in subsonic applications much above 20,000 feet because of the greatly reduced rates of sublimation at lower temperatures (less than -4 degrees Fahrenheit). Both oil flow and sublimating chemicals have the disadvantage of providing only one good data point per flight. Thus, for many important flight conditions, transition visualization has not been readily available. This paper discusses a new method for visualizing transition in fight by the use of liquid crystals. The new method overcomes the limitations of past techniques, and provides transition visualization capability throughout almost the entire altitude and speed ranges of virtually all subsonic aircraft flight envelopes. The method also has wide applicability for supersonic transition visualization in flight and for general use in wind tunnel research over wide subsonic and supersonic speed ranges.

Description: Chemical and thermal nonequilibrium phenomena are studied in the stagnation region of a hypervelocity blunt body. This investigation is motivated by the need to predict the heat-transfer rate to the leading edge of aeromaneuvering orbital transfer vehicles. Flight speeds of approximately 10 km/s at altitudes of approximately 80 km are considered for body radii of 1-50 cm. The analysis is based on continuum theory and is applicable to the viscous and incipient merged layer regimes of rarefied flow. A two-species, two-temperature gas model is assumed. Comparisons are made with previous theories, experimental data, and results based on the thermodynamic equilibrium assumption. The equation accounting for vibrational nonequilibrium is presented and its effects on flow properties are discussed. Parameters requiring further investigation are identified. Preliminary results indicate that the inclusion of vibrational relaxation has little effect on the heat-transfer rate for a fully catalytic surface. However, vibrational nonequilibrium may increase the heat-transfer rate to a noncatalytic surface, depending on the degree of nonequilibrium.

Description: The presence of tip stores influences both the aerodynamic and aeroelastic performances of wings. Such effects are more pronounced in the transonic regime. In this study, a theoretical method is developed, for the first time, to compute unsteady transonics of oscillating wings with tip stores. The method is based on the small-disturbance aerodynamic equations or motion from the potential-flow theory. To validate the method, subsonic and transonic aerodynamic computations are made for a wing of low aspect ratio, and they are compared with the available experimental data. The comparisons are favorable. The strong effects of the tip store on the transonic aerodynamics on the wing are also illustrated. The method developed in this study can be used for transonic aeroelastic computations of wings with tip stores.

Description: A full span propulsive wing/canard model is to be tested in the NASA Langley Research Center (LaRC) 4 x 7 meter low speed wind tunnel. These tests are a continuation of the tests conducted in Feb. 1984, NASA test No.290, and are being conducted under NASA Contract NAS1-17171. The purpose of these tests is to obtain extensive lateral-directional data with a revised fuselage concept. The wings, canards, and vertical tail of this second test series model are the same as tested in the previous test period. The fuselage and internal flow path have been modified to better reflect an external configuration suitable for a fighter airplane. Internal ducting and structure were changed as required to provide test efficiency and blowing control. The model fuselage tested during the 1984 tests was fabricated with flat sides to provide multiple wing and canard placement variations. The locations of the wing and canard are important variables in configuration development. With the establishment of the desired relative placement of the lifting surfaces, a typically shaped fuselage has been fabricated for these tests. This report provides the information necessary for the second series tests of the propulsive wing/canard model. The discussion in this report is limited to that affected by the model changes and to the second series test program. The pretest report information for test 290 which is valid for the second series test was published in Rockwell report NR 83H-79. This report is presented as Appendix 1 and the modified fuselage stress report is presented as Appendix 2 to this pretest report.

Description: Prediction of aerodynamic loads on bodies in arbitrary motion is considered from an acoustic point of view, i.e., in a frame of reference fixed in the undisturbed medium. An inhomogeneous wave equation which governs the disturbance pressure is constructed and solved formally using generalized function theory. When the observer is located on the moving body surface there results a singular linear integral equation for surface pressure. Two different methods for obtaining such equations are discussed. Both steady and unsteady aerodynamic calculations are considered. Two examples are presented, the more important being an application to propeller aerodynamics. Of particular interest for numerical applications is the analytical behavior of the kernel functions in the various integral equations.

Description: Research at Langley on skin friction drag was described in Tech Briefs. 3M engineers suggested to Langley that grooves molded into a lightweight plastic film with adhesive backing and pressed on an airplane would be simpler than cutting grooves directly onto the surface. Boeing became involved and tested the "riblet" on an olympic rowing shell; the US won a silver medal. Based on the riblet-like projections on shark's skins, the technology may provide a 5 percent fuel saving for airplanes. Product is no longer commercially available.

Description: A new rotor blade tip design called the free-tip has been proposed as a means to improve forward flight performance characteristics and reduce oscillatory loads. The free-tip design incorporates a tip that is free to pitch independently of the rest of the blade. Pitching about an axis forward of the quarter-chord, the tip weathervanes into its local wind, thus reducing angle of attack perturbations and the resulting oscillatory lift loadings. A nearly constant nose-up pitching moment is applied mechanically to the tip so that the tip, to maintain pitching equilibrium, produces nearly steady positive lift around the azimuth. A wind-tunnel test of a small-scale, 5.1 m diameter model rotor was conducted to obtain comparative forward flight performance and oscillatory loads data with the tips free and fixed. The free-up was shown to reduce power in trimmed flight over a wide range of advance ratio and thrust; at an advance ratio of 0.3 and C(sub L)/sigma of 0.08 the reduction is 12%. Oscillatory flapwise bending-moments and oscillatory pitch link loads are also reduced, but the oscillatory in-plane bending moments increase.

Description: Small blade-to-blade property differences are investigated to determine how they affect the behavior of a simple rotor-body system. An analytical approach is used which emphasizes the significance of these effects from the experimental point of view. It is found that the primary effect of blade-to-blade dissimilarities is the appearance of additional peaks in the frequency spectrum which are separated from the conventional response peaks by multiples of the rotor speed. These additional responses are potential experimental problems because when they occur near a mode of interest they act as contaminant frequencies which can make damping measurements difficult. Increased rotor-body coupling and a rotor shaft degree of freedom act to improve the situation by altering the frequency separation of the modes.

Description: The dissociating and ionizing nonequilibrium flows behind a normal shock wave are calculated for the density and vehicle regimes appropriate for aeroassisted orbital transfer vehicles; the departure of vibrational and electron temperatures from the gas temperature as well as viscous transport phenomena are accounted for. From the thermodynamic properties so determined, radiative power emission is calculated using an existing code. The resulting radiation characteristics are compared with the available experimental data. Chemical parameters are varied to Investigate their effect on the radiation characteristics. It is concluded that the current knowledge of rate chemistry leads to a factor-of-4 uncertainty In nonequilibrium radiation intensities. The chemical parameters that must be studied to Improve the accuracy are identified.

Description: An analytical procedure for the determination of the shape of a Leading-Edge Extension (LEE) which satisfies design criteria, including especially noninterference at the wing design point, has been developed for thick delta wings. The LEE device best satisfying all criteria is designed to be mounted on a wing along a dividing stream surface associated with an attached flow design lift coefficient (C(sub L,d)) of greater than zero. This device is intended to improve the aerodynamic performance of transonic aircraft at C(sub L) greater than C(sub L,d) system emanating from the LEE leading edge. In order to quantify this process a twisted and cambered thick delta wing was chosen for the initial application of this design procedure. Appropriate computer codes representing potential and vortex flows were employed to determine the dividing stream surface at C(sub L,d) and an optimized LEE planform shape at C(sub L) greater than C(sub L,d), respectively. To aid in the LEE selection, the aerodynamic effectiveness of 36 planforms was investigated at C(sub L) greater than C(sub L,d). This study showed that reducing the span of the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, regardless of the shape or area. Furthermore, for a fixed area, constant-chord LEE candidates were relatively more efficient than those with sweep less than the wing. At C(sub L,d), the presence of the LEE planform best satisfying the design criteria was found to have no effect on the wing alone aerodynamic performance.

Description: The paper describes the development of a thick (t/c = 0.18) transonic, multifoil, blown augmentor-wing section and discusses the results of a series of wind-tunnel tests on the configuration. The results show that the blown multifoil section enjoys two advantages over a conventional unblown single-foil supercritical section or the same overall thickness-chord ratio: 1) "effective" drag reduced by blowing, and 2) increased drag rise Mach number (M(sub D) = 0.75); they also demonstrate that augmentor blowing improves the buffet boundaries of the section. Thus, overall, it has been shown that the augmentor flap configuration is capable of extending the speed range of a jet transport aircraft to the very low approach speeds required by STOL aircraft [as demonstrated by the NASA/DITC (Canadian Department of Industry Trade and Commerce) augmentor-wing STOL research aircraft] and also to the high subsonic speed required for cruise, where it is shown to be competitive with the plain supercritical airfoil.

Description: An investigation has been conducted in the Langley spin tunnel to determine the spin and recovery characteristics of a 1/20-scale model of the Northrop F-5E airplane. The investigation included erect and inverted spins, a range of center-of- gravity locations and moments of inertia, symmetric and asymmetric store loadings, and a determination of the parachute size required for emergency spin recovery. The effects of increased elevator trailing-edge-up deflections, of leading-edge and trailing-edge flap deflections, and of simulating the geometry of large external stores were also determined.

Description: A method is developed to determine the time-dependent flowfield about an impulsively started circular cylinder. An outer potential flow model is interfaced with an inner viscous flow region. The wake is described by a set of elementary point vortices. The position at which the point vortices are shed from the cylinder is obtained from a solution to the unsteady incompressible laminar boundary-layer equations. A rear shear-layer is postulated to account for backflow induced vorticity. Wake development is detailed from the initial formation of the two symmetric vortices to subsequent asymmetry and eventual alternate shedding. Unsteady pressure distributions, lift and drag forces, and Strouhal number are calculated and compared with experiment.

Description: Longitudinal and lateral-directional estimates of the aerodynamic derivatives of the X-24B research aircraft were obtained from flight data by using a modified maximum likelihooa estimation method. Data were obtained over a Mach number range from 0.35 to 1.72 and over an angle of attack range from 3.5deg to 15.7deg. Data are presented for a subsonic and a transonic configuration. The flight derivatives were generally consistent and documented the aircraft well. The correlation between the flight data and wind-tunnel predictions is presented and discussed.

Description: No abstract available

Description: The aerodynamic forces on an oscillating airfoil or airfoil-aileron combination of three independent degrees of freedom have been determined. The problem resolves itself into the solution of certain definite integrals, which have been identified as Bessel functions of the first and second kind and of zero and first order. The theory, being based on potential flow and the Kutta condition, is fundamentally equivalent to the conventional wing-section theory relating to the steady case. The air forces being known, the mechanism of aerodynamic instability has been analyzed in detail. An exact solution, involving potential flow and the adoption of the Kutta condition, has been analyzed in detail. An exact solution, involving potential flow and the adoption of the Kutta condition, has been arrived at. The solution is of a simple form and is expressed by means of an auxiliary parameter K.

Description: The purpose of this presentation is to give you a survey of a field of aerodynamics which has for a number of years been attracting an ever growing interest. The subject is the theory of flows with friction, and, within that field, particularly the theory of friction layers, or boundary layers. As you know, a great many considerations of aerodynamics are based on the so-called ideal fluid, that is, the frictionless incompressible fluid. By neglect of compressibility and friction the extensive mathematical theory of the ideal fluid (potential theory) has been made possible.

Description: An investigation has been made in the Langley stability tunnel to determine the low-speed static stability and control characteristics of a model of the Bell MX-776. The results of the investigation indicated that the basic model configuration was longitudinally stable in the angle-of-attack range from about -16 deg. to 16 deg. but that the stability was a minimum near O deg angle of attack. The data indicated an aerodynamic-center position about 0.64 body diameters behind the center of gravity at low angles of attack. Reduction in the size of the front horizontal fins increased the longitudinal stability. With 20 percent of the span of the normal front horizontal fins cut off the aerodynamic center was about 1.04 body diameters behind the center of gravity, and with front horizontal fins having the same area as the front vertical fins, the aerodynamic center was 2.26 body diameters behind the center of gravity (at low angles of attack).

Description: Rocket-powered models were flown at high-subsonic, transonic, and supersonic speeds to determine the zero-lift drag of fin-stabilized parabolic bodies of revolution differing in fineness ratio and in position of maximum diameter. The present paper presents the results for fineness ratio 12.5, 8.91 and 6.04 bodies having maximum diameters located at stations of 20, 40, 60, and 80 percent of body length. All configurations had cut-off sterns and all had equal base, frontal, and exposed fin areas. For most of the supersonic-speed range models having their maximum diameters at the 60-percent station gave the lowest values of drag coefficient. At supersonic speeds, increasing the fineness ratio generally reduced the drag coefficient for a given position of maximum diameter.

Description: A supersonic compressor design having supersonic velocity at the entrance of the stator is analyzed on the assumption of two-dimensional flow. The rotor and stator losses assumed in the analysis are based on the results of preliminary supersonic cascade tests. The results of the analysis show that compression ratios per stage of 6 to 10 can be obtained with adiabatic efficiency between 70 and 80 percent. Consideration is also given in the analysis to the starting, stability, and range of efficient performance of this type of compressor. The desirability of employing variable-geometry stators and adjustable inlet guide vanes is indicated. Although either supersonic or subsonic axial component of velocity at the stator entrance can be used, the cascade test results suggest that higher pressure recovery can be obtained if the axial component is supersonic.

Description: In the Institute for Flight Mechanics of the DVL a reactor arrangement with a maximum output of 100 kg was investigated as an expedient for the termination of dangerous spins on an airplane of the FW 56 type. reproduce the influence of a disturbance of the steady spin condition by a pitching or yawing moment. The tests were meant to reproduce the influence of a disturbance of the steady spin condition by a pitching and yawing moment.

Description: When auxiliary jet engines are installed on airframes; as well as in some new designs, the jet engines are mounted in such a way that the jet stream exhausts in close proximity to the fuselage. This report deals with the behavior of the jet in close proximity to a two-dimensional surface. The experiments were made to find out whether the axially symmetric stream tends to approach the flat surface. This report is the last of a series of four partial test reports of the Goettingen program for the installation of jet engines, dated October 12, 1943. This report is the complement of the report on intake in close proximity to a wall.

Description: In an earlier report UM No.1117 by Gothert,the single-source method was applied to the compressible flow around circles, ellipses, lunes, and around an elongated body of revolution at different Mach numbers and the results compared as far as possible with the calculations by Lamla ad Busemann. Essentially, it was found that with favorable source arrangement the single-source method is in good agreement with the calculations of the same degree of approximation by.Lamla and Busemann. Near sonic velocity the number of steps must be increased considerably in order to sufficiently approximate the adiabatic curve. After exceeding a certain Mach number where local supersonic fields occur already, it was no longer possible, in spite of the substantially increased number of steps, to obtain a systematic solution because the calculation diverged. This result,was interpreted to mean that above this point of divergence the symmetrical type of flow ceases to exist and changes into the unsymmetrical type characterized by compressibility shocks.

Description: The problem of the motion of an elongated body of revolution in an incompressible fluid may, as is known, be solved approximately with the aid of the distribution of sources along the axis of the body. In determining the velocity field, the question of whether the body moves uniformly or with an acceleration is no factor in the problem. The presence of acceleration must be taken into account in determining the pressures acting on the body. The resistance of the body arising from the accelerated motion may be computed either directly on the basis of these pressures or with the aid of the so-called associated masses (inertia coefficients). A different condition holds in the case of the motion of bodies in a compressible gas. In this case the finite velocity of sound must be taken into account.

Description: Various ways were tried recently to decrease the friction drag of a body in a flow; they all employ influencing the boundary layer. One of them consists in keeping the boundary layer Laminar by suction; promising tests have been carried out. Since for large Reynolds numbers the friction drag of the laminar boundary layer is much lower than that of the turbulent boundary layer, a considerable saving in drag results from keeping the boundary layer laminar, even with the blower power required for suction taken into account. The boundary layer is kept laminar by suction in two ways: first, by reduction of the thickness of the boundary layer and second, by the fact that the suction changes the form of the velocity distribution so that it becomes more stable, in a manner similar to the change by a pressure drop. There by the critical Reynolds number of the boundary layer (USigma*/V) (sub crit) becomes considerably higher than for the case without suction. This latter circumstance takes full effect only if continuous suction is applied which one might visualize realized through a porous wall. Thus the suction quantities required for keeping the boundary layer laminar become so small that the suction must be regarded as a very promising auxiliary means for drag reduction.

Description: Four component measurements of 12 wings of symmetric profile having flaps with chord ratios t(sub R)/t(sub L) = 0.3 and t(sub R)/t(sub L) = 0.2 are treated in this report. As a result of the investigations, the effects of plan form and gap between fixed surface and control surface have been clarified. Lift, drag, pitching moment, and hinge moment were measured in the control-surface deflection range: -23 deg 〈 or = beta 〈 or = 23 deg and the range of angle of attack: -20 deg 〈 or = alpha 〈 or = 20 deg. Six wings with flaps of small chord (t(sub R)/t(sub L) 〈 0.1) were investigated at large flap settings.

Description: The present report describes a new method for the prediction of the flow pattern of a gas in the two-dimensional and axially symmetrical case. It is assumed that the expansion of the gas is adiabatic and the flow stationary. The several assumptions necessary of the nozzle shape effect, in general, no essential limitation on the conventional nozzles. The method is applicable throughout the entire speed range; the velocity of sound itself plays no singular part. The principal weight is placed on the treatment of the flow near the throat of a converging-diverging nozzle. For slender nozzles formulas are derived for the calculation of the velocity components as function of the location.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/29-scale model of the Republic XF-91 airplane with a.conventional-tail arrangement installed. Previously, tests were made on the model with a vee tail installed. The erect spin and recovery characteristics of the model were determined for the normal loading with the wing installed at various amounts of incidence. The spin investigation also included inverted-spin tests, spin-recovery-parachute tests, tests with the center of gravity moved rearward, and tests with external fuel tanks added to the model. In addition, several tail.modifications were tested,on the model in an attempt, to improve the model's spin-recovery characteristics. The results indicate that any fully developed spin obtained on the airplane with the conventional tail installed will be satisfactorily terminated if rudder reversal is accompanied by moving the ailerons with the spin (stick right in a right spin).Decreasing the wing incidence from 6deg to -2deg should have a beneficial effect on the recovery characteristics of the airplane. Recovery characteristics by normal use of controls (full rudder reversal followed by moving the elevators down) will be satisfactory if the wing incidence,of the airplane is -2deg. Installation of external fuel tanks (with or without fuel) will have a somewhat adverse effect on the recovery characteristics of the airplane, but if the recovery technique includes movement of the ailerons to full with the spin, the spin rotation will be terminated rapidly. Varying the position of the center of gravity within the limits indicated to be possible on the airplane should not affect the recovery characteristics.

Description: The plane problem of the vibrating airfoil in supersonic flow is dealt with and solved within the scope of a linearized theory by the method of the acceleration potential.

Description: A supplementary investigation on the stabilization of the Jettisonable nose section of the X-2 airplane has been conducted in the Langley 20-foot free-spinning tunnel. It was found that the nose section could be stabilized by the addition of curved fins which could be folded against the fuselage for normal flight.

Description: The characteristics of a cargo-dropping device having extensible rotating blades as load-carrying surfaces have been studied in simulated vertical descent in the Langley 20-foot free-spinning tunnel. The investigation included tests to determine the variation in vertical sinking speed with load. A study of the blade characteristics and of the test results indicated a method of dynamically balancing the blades to permit proper functioning of the device.

Description: A 0.1-size powered dynamic model of a large, high-speed flying boat was landed in Langley tank no. 1 into oncoming waves 4 feet high (full size). The model was tested with two afterbodies of differing lengths (4.12 and 6.63 beams). The short afterbody had a constant angle of dead rise of 22.5deg and a keel angle of 6.5deg. The long afterbody had warped dead rise and a keel angle of 8.5deg. The vertical accelerations were slightly greater and the maximum angular accelerations and maxim= trims were slightly less for the model with the long afterbody than for the model with -the short afterbody. A wave length of 210 feet (full size) imposed the highest accelerations on the model with either the long or the short afterbody.

Description: The inlet wide vanes for the supersonic compressor of the XJ55-FF-1 engine were studied as a separate component in order to determine the performance prior to installation in the compressor test rig. Turning angles approached design values, and increased approximately to through the inlet Mach number range from 0.30 to choke. A sharp break in turning angle was experienced when the choke condition was reached. The total-pressure loss through the guide vanes was approximately 1 percent for the unchoked conditions and from 5 to 6 percent when choked.

Description: During the past several years it has been necessary for aeronautical research workers to exert a good portion of their effort in developing the means for conducting research in the high-speed range. The transonic range particularly has presented a very acute problem because of the choking phenomena in wind tunnels at speeds close to the speed of sound. At the same time, the multiplicity of design problems for aircraft introduced by the peculiar flow problems of the transonic speed range has given rise to an enormous demand for detail design data. Substantial progress has been made, however, in developing the required research techniques and in supplying the demand for aerodynamic data required for design purposes. In meeting this demand, it has been necessary to resort to new techniques possessing such novel features that the results obtained have had to be viewed with caution. Furthermore, the kinds of measurements possible with these various techniques are so varied that the correlation of results obtained by different techniques generally becomes an indirect process that can only be accomplished in conjunction with the application of estimates of the extent to which the results of measurements by any given technique are modified by differences that are inherent in the techniques. Thus, in the establishment of the validity and applicability of data obtained by any given technique, direct comparisons between data from different sources are a supplement to but not a substitute for the detailed knowledge required of the characteristics of each technique and fundamental aerodynamic flow phenomena.

Description: Lately it has been proposed to reduce the friction drag of a body in a flow for the technically important large Reynolds numbers by the following expedient: the boundary layer, normally turbulent, is artificially kept laminar up to high Reynolds numbers by suction. The reduction in friction drag thus obtained is of the order of magnitude of 60 to 80 percent of the turbulent friction drag, since the latter, for large Reynolds numbers, is several times the laminar friction drag. In considering the idea mentioned one has first to consider whether suction is a possible means of keeping the boundary layer laminar. This question can be answered by a theoretical investigation of the stability of the laminar boundary layer with suction. A knowledge, as accurate as possible, of the velocity distribution in the laminar boundary layer with suction forms the starting point for the stability investigation. E. Schlichting recently gave a survey of the present state of calculation of the laminar boundary layer with suction.

Description: An analysis is presented of the influence of wing aspect ratio and tail location on the effects of compressibility upon static longitudinal stability. The investigation showed that the use of reduced wing aspect ratios or short tail lengths leads to serious reductions in high-speed stability and the possibility of high-speed instability.

Description: An experimental investigation was conducted to determine the penetration of a circular air Jet directed perpendicularly to an air stream as a function of Jet density, Jet velocity, air-stream density, air-stream velocity, Jet diameter, and distance downstream from the Jet. The penetration was determined for nearly constant values of air-stream density at two tunnel velocities, four Jet diameters, four positions downstream of the Jet, and for a large range of Jet velocities and densities. An equation for the penetration was obtained in terms of the Jet diameter, the distance downstream from the jet, and the ratios of Jet and air-stream velocities and densities.

Description: An investigation of the spin and recovery characteristics of a 1/24-scale model of the Grumman XF9F-2 airplane with wing-tip tanks installed has been conducted-in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect spin and recovery characteristics of the model for a range of possible loadings of the tip tanks were determined. Spin and recovery characteristics without tanks were determined in a previous investigation. The model results indicated that the airplane spins will generally be oscillatory and that recoveries will be satisfactory for all loadings by normal recovery technique (full rudder reversal followed approximately one-half turn later by moving the elevator down). The rudder force necessary for recovery should be within the physical capability of the pilot but the elevator force may be excessive so that some type of balance or booster might be necessary, or it might be necessary to jettison the wing-tip tanks.

Description: A supplementary wind-tunnel investigation has been conducted to determine the effect of rearward positions of the center of gravity on the spin, longitudinal-trim, and tumbling characteristics of the 1/20-scale model of the Consolidated Vultee 7002 airplane equipped with the single vertical tail. A few tests were also made with dual vertical tails added to the model. The model was ballasted to represent, the airplane in its approximate design gross weight for two center-of-gravity positions, 3O and 35 percent of the mean aerodynamic chord. The original tests previously reported were for a center-of-gravity position of 24 percent of the mean aerodynamic chord.

Description: At the request of the Air Material Command, U. S. Air Force, a theoretical study has been made of the dynamic lateral stability characteristics of the MX-838 (XB-51) airplane. The calculations included the determination of the neutral-oscillatory-stability boundary (R = 0), the period and time to damp to one-half amplitude of the lateral oscillation, end the time to damp to one-half amplitude for the spiral mode. Factors varied in the investigation were lift coefficient, wing incidence, wing loading, and altitude. The results of the investigation showed that the lateral oscillation of the airplane is unstable below a lift coefficient of 1.2 with flaps . deflected 40deg but is stable over the entire speed range with flaps deflected 20deg or 0deg. The results showed that satisfactory oscillatory stability can probably be obtained for all lift coefficients with the proper variation of flap deflection and wing incidence with airspeed. Reducing the positive wing incidence improved the oscillatory stability characteristics. The airplane is spirally unstable for most conditions but the instability is mild and the Air Force requirements are easily met.

Description: The results of altitude-wind-tunnel tests conducted to determine the performance of an axial-flow-type 4000.pound-thrust turboJet engine for a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.02 to 1.86 are presented and the experimental and analytical methods employed are discussed. By means of suitable generalizing factors applied to the measured performance data, curves were obtained from which the engine performance at any altitude for a given ram pressure ratio can be estimated. The data presented include the windmilling drag characteristics of the turbojet engine for the ranges of altitudes and ram pressure ratios covered by the performance data.

Description: An investigation was made in the Langley high-speed 7-by 10-foot tunnel to determine the high-speed longitudinal stability end con&o1 characteristics of a 0.01-scale model of the Grumman XF9F-2 airplane in the Mach number range from 0.40 to 0.85. The results indicated that the lift and drag force breaks occurred at a Mach number of about 0.76. The aerodynamic-center position moved rearward after the force break and control position stability was present for all Mach numbers up to a Mach number of 0.80.

Description: The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.

Description: This report contains the results of the wind tunnel investigation of the pressure distribution on the flying mock-up of the Consolidated Vultee XP-92 airplane. Data are presented for the pressure distribution over the wing, vertical tail and the fuselage, and for the pressure loss and rate of flow through the ducted fuselage. Data are also presented for the calibration of two airspeed indicators, and for the calibration of angle-of-attack and sideslip-angle indicator vanes.

Description: Pressure measurements were made during wind-tunnel tests of the McDonnell XP-85 parasite fighter. Static-pressure orifices were located over the fuselage nose, over the canopy, along the wing root, and along the upper and lower stabilizer roots. A total-pressure and static-pressure rake was located in the turbojet engine air-intake duct. It was installed at the station where the compressor face would be located. Pressure data were obtained for two airplane conditions, clean and with skyhook extended, through a range of angle of attack and a range of yaw.

Description: No abstract available

Description: Performance characteristics of the turbine of a 4000-pound-thrust axial-flow turbojet engine was determined in investigations of the complete engine in the NACA Cleveland altitude wind tunnel. Characteristics are presented as functions of the total-pressure ratio across the turbine and of turbine speed and gas flow corrected to sea-level conditions. Three turbine nozzles of different areas were used to determine the area that gave optimum performance. Inasmuch as tail-pipe nozzles of different diameters were investigated in combination with the standard turbine nozzle, the effect of varying discharge conditions on turbine operation could be observed. The investigations covered a range of pressure attitudes from 5000 to 40,000 feet. The engine was investigated over the entire operable range of speeds at each altitude. At pressure altitude of 30,000 feet, the effect on turbine operation of varying the ram pressure ration over a range from 1.10 to 1.77 was evaluated. An altitude effect was apparent when turbine pressure ratio was plotted against corrected turbine speed but it was so slight as to be negligible insofar as the turbine efficiencies were concerned. A maximum turbine efficiency of slightly more than 82 percent was obtained with the configuration using the standard turbine nozzle and the low-flow compressor. This efficiency, which is somewhat lower than the actual turbine efficiency, is uncorrected for accessories drive power, bearing friction, tail-pipe pressure drop, compressor thermal radiation, and introduction of turbine-disk cooling air into the gas stream. Changes in the ram pressure ratio had a negligible effect on the turbine efficiency.

Description: An investigation of the Ex-3 pine-cone-head pellet was made in the Langley high-speed 7-by 10-foot wind tunnel to determine the static force and moment characteristics at high Mach numbers with the reference center of gravity located at 37.5 percent of the over-all length aft of the nose. For this center-of-gravity location there were no secondary trim positions, and the center-of-pressure position was not appreciably affected by Mach number.

Description: A series of calculations of the dynamic response of airplane wings to gusts were made with the purpose of showing the relative response of a reference airplane, the DC-3 airplane, and of newer types of airplanes represented by the DC-4, DC-6, and L-49 airplanes. Additional calculations were made for the DC-6 airplane to show the effects of speed and altitude. On the basis of the method of calculation used and the conditions selected for analysis, it is indicated that: 1) The newer airplanes show appreciably greater dynamic stress in gusts then does the reference airplane; 2) Increasing the forward speed or the operating altitude results in an increase of the dynamic stress ratio for the gust with a gradient distance of 10 chords.

Description: The positions of boundary-layer transition were ascertained experimentally for a swept-back wing and a wing without sweepback which were alike in all other respects and were compared for the same angle of attack (R(sub e) = 5.6 x 10(exp 5)). The swept-back wing in a definite range of angle of attack resulted in a backward shift of the transition point on the suction side of the wing. The favorable effect of sweepback on the position of the transition point is confirmed, consequently. In addition to decreasing the drag at high Mach numbers, the swept-back wing is acknowledged to have additional advantages. These are: (1) Decrease of the pressure drag. The reduction factor is approximately equal to the cosine of the angle of sweepback. (2) Backward shift of the transition point. There are no known experiments which establish experimentally the advantage anticipated. It appeared justifiable, therefore, to carry out some fundamental experiments which might furnish some idea of the magnitude of the advantage expected. Such an experiment is reported in what follows; the advantage of the sweepback appears clearly.

Description: A brief investigation was made of the longitudinal-stability characteristics of a YF-84A airplane (Army Serial No. 45-79488). The airplane developed a pitching-up tendency at approximately 0.80 Mach number which necessitated large push forces and down-elevator deflections for further increases in speed. In steady turns at 35,000 feet with the center of gravity at 28.3 percent mean aerodynamic chord for normal accelerations up to the maximum test value, the control-force gradients were excessive at Mach numbers over 0.78. Airplane buffeting did not present a serious problem in accelerated or unaccelerated flight at 15,000 and 35,000 feet up to the maximum test Mach number of 0.84. It is believed that excessive control force would be the limiting factor in attaining speeds in excess of 0.84 Mach number, especially at altitudes below 35,000 feet.

Description: The present report deals with force- and pressure-distribution measurements on a number of fuselage forms of varying slenderness ratio, varying rearward position of maximum thickness, and varying nose ratio. The effect of these parameters on the force and moment coefficients was determined. The linearity of the difference between the theoretical and experimental fuselage moments with the friction lift made it possible to indicate a neutral point and its travel with the different parameters. The pressure-distribution measurements yielded absolute values for the increase of velocity. A comparison with the theory indicated good agreement at small angles of attack, but considerable differences at greater angles of attack, where potential flow could no longer be assumed.

Description: This report contains the results of the investigation of the aerodynamic characteristics of the flying mock-up of the Consolidated Vultee XP-92 airplane as conducted in the Ames 40- by 80-foot wind tunnel, Data are presented for test conditions which would give information as to the limits of stability and controllability, and also, the effect of Reynolds number. No analysis of the data has been made.

Description: Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll af the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device, The maximum lift coefficient of the model with split flaps and the original partial-span straight slats was only 1.2; whereas a value of approximately 1.8 was obtained by drooping the slat and extending it full span, Improvement in maximum lift of approximately the same amount resulted when a full-span nose flap was substituted for the original partial-span slat.

Description: Flight tests have been made to determine the longitudinal stability and control and stalling characteristics of the P-47.E-30 airplane. The teat results show the airplane to be unstable stick free in any power-on condition even at the most forward center-of-gravity position tested. At the rearward center-of-gravity position tested the airplane also had neutral to negative stick-fixed stability with power on. The characteristics in accelerated flight were acceptable at the forward center-of-gravity position at low and high altitudes except at high speed where the control-force variations with acceleration were high. At the rearward center-of-gravity position, elevator-force reversals were experienced in turns at low speeds, and the force per g was low at all the other speeds. Ample stall warning was afforded in all the conditions tested and the stalling characteristics were very satisfactory except in the approach and wave-off conditions.

Description: An investigation to determine the performance and operational characteristics of an axial-flow gas turbine-propeller engine was conducted in the Cleveland altitude wind tunnel. As part of this investigation, the combustion-chamber performance was determined at pressure altitudes from 5000 to 35,000 feet, compressor-inlet ram-pressure ratios of 1.00 and 1.09, and engine speeds from 8000 to 13,000 rpm. Combustion-chamber performance is presented as a function of corrected engine speed and corrected horsepower. For the range of corrected engine speeds investigated, overall total-pressure-loss ratio, cycle efficiency, and the fractional loss in cycle efficiency resulting from pressure losses in the combustion chambers were unaffected by a change in altitude or compressor-inlet ram-pressure ratio. For the range of corrected horsepowers investigated, the total-pressure-loss ratio and the fractional loss in cycle efficiency resulting from pressure losses in the combustion chambers decreased with an increase in corrected horsepower at a constant corrected engine speed. The combustion efficiency remained constant for the range of corrected horsepowers investigated at all corrected engine speeds.

Description: An investigation has been conducted to determine the opening characteristics of several hemispherical parachutes and to study the influence of the parachute design variables on these opening characteristics. The effects of design variables on the drag and stability characteristics of the parachutes were also evaluated. The tests were made in the Langley 20-foot free-spinning tunnel and in the Langley 300 MPH 7 by 10-foot tunnel.

Description: Contains experimental results of an investigation of the aerodynamic characteristics of a family of flying boat hulls of length beam ratios 6, 9, 12, and 15 without wing interference. The results are compared with those taken on the same family of hulls in the presence of a wing.

Description: A Westinghouse 24C-2 combustor was investigated at conditions simulating operation of the 24C Jet engine at zero ram over ranges of altitude and engine speed. The investigation was conducted to determine the altitude operational limits, that is, the maximum altitude for various engine speeds at which an average combustor-outlet gas temperature sufficient for operation of the jet engine could be obtained. Information was also obtained regarding the character of the flames, the combustion efficiency, the combustor-outlet gas temperature and velocity distributions, the extent of afterburning, the flow characteristics of the fuel manifolds, the combustor inlet-to-outlet total-pressure drop, and the durability of the combustor basket. The results of the investigation indicated that the altitude operational limits for zero ram decreased from 12,000 feet at an engine speed of 4000 rpm to a minimum of 9000 feet at 6000 rpm, and thence increased to 49,000 feet at 12,000 rpm.. At altitudes below the operational limits, flames were essentially steady, but, at altitudes above the operational limits, flames were often cycling and either blew out or caused violent explosions and vibrations. At conditions on the altitude operational limits the type of combustion varied from steady to cycling with increasing fuel-air ratio and the reverse occurred with decreasing fuel-air ratio. In the region of operation investigated, the combustion efficiency ranged from 75 to 95 percent at altitudes below the operational limits and dropped to 55 percent or less at some altitudes above the operational limits. The deviations in the local combustor-outlet gas temperatures were within +20 to -30 percent of the mean combustor temperature rise for inlet-air temperatures at the low end of the range investigated, but became more uneven (up to +/-100 percent) with increasing inlet-air temperatures. The distribution of the combustor-outlet gas velocity followed a similar trend. Practically no afterburning downstream of the combustor outlet occurred. At conditions of high inlet-air temperature several factors indicated that fuel vapor or air formed in the fuel manifolds and adversely affected combustion. The combustor inlet-to-outlet total-pressure drop can be correlated as a function of the ratio of the combustion-air inlet density to outlet density and of the inlet dynamic pressure. The walls of the combustor basket were warped and burned during 29 hours of operation.

Description: The present report deals with the processes accompanying the planing of a planing boat or a seaplane on water . The study is largely based upon theoretical investigations; mathematical problems and proofs are not discussed. To analyze theoreticaly actual planing processes, giving due consideration to all aspects of the problem, is probably not possible. The theories therefore treat various simple limiting cases, which in their entirety give a picture of the planing processes and enable the interpretation of the experimental results. The discussion is concerned with the stationary planing attitude: the boat planes at a constant speed V on an originally smooth surface.

Description: Pressure distribution over an extended leading-edge flap on a 42 degree swept-back wing was investigated. Results indicate that the flap normal-force coefficient increased almost linearly with the angle of attack to a maximum value of 3.25. The maximum section normal-force coefficient was located about 30 percent of the flap span outboard of the inboard end and had a value of 3.75. Peak negative pressures built up at the flap leading edge as the angle of attack was increased and caused the chordwise location of the flap center of pressure to be move forward.

Description: Investigations were conducted to determine effectiveness of refrigerants in increasing thrust of turbojet engines. Mixtures of water an alcohol were injected for a range of total flows up to 2.2 lb/sec. Kerosene was injected into inlets covering a range of injected flows up to approximately 30% of normal engine fuel flow. Injection of 2.0 lb/sec of water alone produced an increase in thrust of 35.8% of rate engine conditions and kerosene produced a negligible increase in thrust. Carbon dioxide increased thrust 23.5 percent.

Description: In the course of a flight test of a supersonic research pilotless aircraft (the NACA RM-1), large-amplitude aileron oscillations, probably aileron compressibility flutter, were encountered in the transonic and supersonic speed ranges. The wing was oscillating at the same frequency as the aileron. The aircraft was equipped with 45 degree swept-back wings of symmetrical NASA 65-010 airfoil section. Completely mass-balanced ailerons with 20 degree beveled trailing edges were installed on the wings. The ailerons were free floating with no mechanical restraining force other than the friction of the aileron hinges and servomechanism bearings throughout the high-speed interval of flight.

Description: A three-dimensional investigation of straight-sided-profile plain ailerons on a wing with 30 degrees and 45 degrees of sweepback and sweepforward was made in a high-speed wind tunnel for aileron deflections from -10 degrees to 10 degrees and at Mach numbers from 0.60 to 0.96. Wing configurations of 30 degrees generally reduced the severity of the large changes in rolling-moment and aileron hinge-moment coefficients experienced by the upswept wing configurations as the result of compression shock and extended to higher Mach numbers the speeds at which such changes occurred.

Description: On the basis of a recently developed theory for finite sweptback wings at supersonic speeds, calculations of the supersonic wave drag at zero lift were made for a series of wings having thin symmetrical biconvex sections with untapered plan forms and various angles of sweepback and aspect ratios. The results are presented in a unified form so that a single chart permits the direct determination of the wave drag for this family of airfoils for an extensive range of aspect ratio and sweepback angle for stream Mach numbers up to a value corresponding to that at which the Mach line coincides with the wing leading edge. The calculations showed that in general the wave-drag coefficient decreased with increasing sweepback. At Mach numbers for which the Mach lines are appreciably ahead of the wing leading edge, the 'wave-drag coefficient decreased to an important extent with increases in aspect ratio or slenderness ratio. At Mach numbers for which the Mach lines approach the wing leading edge (Mach numbers approaching a value equal to the secant of the angle of sweepback), the wave-drag coefficient decreased with reductions in aspect ratio or slenderness ratio. In order to check the results obtained by the theory, a comparison was made with the results of tests at the Langley Memorial Aeronautical Laboratory of sweptback wing attached to a freely falling body. The variation of the drag with Mach number and aspect ratio as given by the theory appeared to be in reasonable

Description: No abstract available

Description: An investigation has been conducted in the Cleveland 18- by 18-inch supersonic tunnel at a Mach number of 1.85 and angles of attack from 0 deg to 5 deg to determine optimum design configurations for a convergent-divergent type of supersonic diffuser with a subsonic diffuser of 5 deg included divergence angle. Total pressure recoveries in excess of theoretical recovery across a normal shock at a free-stream Mach number of 1.85 wore obtained with several configurations. The highest recovery for configurations without a cylindrical throat section was obtained with an inlet having an included convergence angle of 20 deg. Insertion of a 2-inch throat section between a 10 deg included angle inlet and the subsonic diffuser stabilized the shock inside the diffuser and resulted in recoveries as high as 0.838 free-stream total pressure at an angle of attack of 0 deg, corresponding to recovery of 92.4 percent of the kinetic energy of the free air stream. Use of the throat section also lessened the reduction in recovery of all configurations due to angle of attack.

Description: Wing was tested with full-span, partial-span, or split flaps deflected 60 Degrees and without flaps. Chordwise pressure-distribution measurements were made for all flap configurations.. Peak values of maximum lift coefficient were obtained at relatively low free-stream Mach numbers and, before critical Mach number was reached, were almost entirely dependent on Reynolds Number. Lift coefficient increased by increasing Mach number or deflecting flaps while critical pressure coefficient was reached at lower free-stream Mach numbers.

Description: Theoretical analysts of lateral dynamic motion of tailless and conventional airplanes was made for fighter and heavy transport. Their reactions to a lateral gust and control power required by each for simple maneuvers were determined and compared. Both types of airplanes require almost identical aileron control power to perform a given maneuver; tailless airplane requires about 1-2 to 1-3 directional control power of conventional airplane. Tailless airplane also shows greatest displacement for a given disturbance and has least damping in oscillatory mode.

Description: Investigations were made to develop a simplified method for designing exhaust-pipe shrouds to provide desired or maximum cooling of exhaust installations. Analysis of heat exchange and pressure drop of an adequate exhaust-pipe shroud system requires equations for predicting design temperatures and pressure drop on cooling air side of system. Present experiments derive such equations for usual straight annular exhaust-pipe shroud systems for both parallel flow and counter flow. Equations and methods presented are believed to be applicable under certain conditions to the design of shrouds for tail pipes of jet engines.

Description: The first part of this paper reviews the present state of the problem of the instability of laminar boundary layers which has formed an important part of the general lectures by von Karman at the first and fourth Congresses and by Taylor at the fifth Congress. This problem may now be considered as essentially solved as the result of work completed since 1938. When the velocity fluctuations of the free-stream flow are less than 0.1 percent of the mean speed, instability occurs as described by the well-known Tollmien-Schlichting theory. The Tollmien-Schlichting waves were first observed experimentally by Schubauer and Skramstad in 1940. They devised methods of introducing controlled small disturbances and obtained measured values of frequency, damping, and wave length at various Reynolds numbers which agreed well with the theoretical results. Their experimental results were confirmed by Liepmann. Much theoretical work was done in Germany in extending the Tol1mien-Schlichting theory to other boundary conditions, in particular to flow along a porous wall to which suction is applied for removing part of the boundary layer. The second part of this paper summarizes the present state of knowledge of the mechanics of turbulent boundary layers, and of the methods now being used for fundamental studies of the turbulent fluctuations in turbulent boundary layers. A brief review is given of the semi-empirical method of approach as developed by Buri, Gruschwitz, Fediaevsky, and Kalikhman. In recent years the National Advisory.Commsittee for Aeronautics has sponsored a detailed study at the National Bureau of Standards of the turbulent fluctuations in a turbulent boundary layer under adverse pressure gradient sufficient to produce separation. The aims of this investigation and its present status are described.

Description: The mutual influences of compression shocks and friction boundary layers were investigated by means of high speed wind tunnels.Schlieren optics provided a clear picture of the flow phenomena and were used for determining the location of the compression shocks, measurement of shock angles, and also for Mach angles. Pressure measurement and humidity measurements were also taken into consideration.Results along with a mathematical model are described.

Description: This report addresses a method for the approximate calculation of compressible flows about profiles with local regions of supersonic velocity. The flow around a slender profile is treated as an example.

Description: At the request of the Air Material Command, Army Air Forces an investigation of the low-speed, power-off stability and control characteristics of the McDonnell XP-85 airplane is being conducted in the Langley free-flight tunnel. The XP-85 airplane is a jet propelled, parasite fighter with a 34 deg sweepback at the wing quarter chord. It was designed to be carried in a bomb bay of the B-36 air plane. The first portion of the investigation consists of a preliminary evaluation of the stability and control characteristics of the airplane from force and fight tests of an unballasted 1/5-scale model. The second portion of the investigation consists of test of a properly balasted 1/10-scale model which will include a study of the stability of the Xp-85 when attached to the trapeze for retraction into the B-36 bomb bay. The results of the preliminary test with the 1/5-scale model are presented herein. This portion fo the investigation included tests of the model with various center fin arrangements. Both the design nose flap and a stall control vane were investigated.

Description: An investigation has been made by the NACA wing-flow method to provide information on the relative longitudinal characteristics of a straight and sweptback wing in the transonic speed range. Tests were made of a semispan model of the Grumman airplane design 83 (XFlOF) incorporating a wing swept back 42.5deg with reference to quarter-chord line and also of the model with the swept wing replaced by a straight wing similar to that of the XF9F airplane. The airfoil sections were symmetrical 64l-series, with thickness ratios of 12 percent for the straight wing and 10 percent for the sweptback wing parallel to the stream direction. Measurements were made of normal force, chord force, and pitching moment at various angles of attack with the two wings both with and without the empennage, and with the fuselage alone. The tests covered a range of effective Mach numbers at the wing of the model from 0.65 to 1.10.

Description: An analysis has been made of the lift control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flap on the NACA 65-210 airfoil section. The analysis indicates that the plain trailing-edge flap employed on the 10-percent-thick airfoil at Mach numbers as high as 0.875 retains at least 50-percent of its low-speed lift-control effectiveness, and is sufficiently effective in lateral control application, assuming a rigid wing, to provide adequate airplane rolling characteristics. The plain trailing-edge flap, as compared to the spoiler and the dive-recovery flap, appears to afford the most favorable characteristics as a device for controlling lift continuously throughout the range of Mach numbers from 0.3 to 0.875. At Mach numbers above those for lift divergence of the wing, either a plain flap or a dive-recovery flap may be used on a thin airplane wing to provide auxiliary wing lift when the airplane is to be controlled in flight, other than in dives, at these Mach numbers. The choice of a lift-control device for this use, however, should include the consideration of other factors such as the increments of drag and pitching moment accompanying the use of the device, and the structural and high-speed aerodynamic characteristics of the airplane which is to employ the device.

Description: On the basis of a recently developed theory for sweptback wings at supersonic velocities, equations are derived for the wave drag of sweptback tapered wings with thin symmetrical double-wedge sections at zero lift. Calculations of section wave-drag distributions and wing wave drag are presented for families of tapered plan forms. Distributions of section wave drag along the span of tapered wings are, in general, very similar in shape to those of untapered plan forms. For a given taper ratio and aspect ratio, an appreciable reduction in wing wave-drag coefficient with increased sweepback is noted for the entire range of Mach number considered. For a given sweep and taper ratio, higher aspect ratios reduce the wing wave-drag coefficient at substantially subcritical supersonic Mach numbers. At Mach numbers approaching the critical value, that is, a value equal to the secant of the sweepback angle, the plan forms of low aspect ratio have lower drag coefficients. Calculations for wings of equal root bending stress (and hence different aspect ratio) indicate that tapering the wing reduces the wing wave-drag coefficient at Mach numbers considerably less than the critical value and a decrease of the drag coefficient with taper at Mach numbers near the critical value.

Description: The previous measurements on airfoils with hinged nose disclosed a comparatively large low-pressure peak at the bend of the hinged nose; which favored the separation of flow. It was therefore attempted to reduce these low-pressure peaks by reducing the camber of the forward profile and thereby ensure a longer adherence of the flow and a maximum lift increase. The forces were measured on a rectangular wing with double-hinged nose and end plates, the pressure distributions were measured in the center section of the wing. The measurements disclosed that the highest lift attained with a single-hinged nose cannot be increased by a double-hinged nose. The sum of the deflection angles of both hinged noses related to the maximum lift is about equal to the corresponding angle of the single-hinge nose (approx. 30 deg to 40). The respective angle of attack in both cases amounts to approx. 21 deg. Even the low-pressure peak is about the same in both cases (P/q approx. -5.5). Therefore, a milder curvature of the forward portion of the profile affords no definite increase of the maximum lift.

Description: The tests on the Russian airfoil 2315 Bis were continued. This airfoil shows, according to Moscow tests, good laminar flow characteristics. Several tests were prepared in the large wind tunnel at Gottingen; partial results were obtained.

Description: The report UM No. 1023/1 which presented the results of measurements for a series of trapezoidal wings was the beginning of a series on wings with aspect ratio 1 to 3 and various contours. In report No. 1023/1 the aspect ratio (Lambda = 4/3) remained the same; the tapering was modified. The present report gives the results of the series of elliptic wings. Here the aspect ratio varies from 1 to 2 with the sweepback. The contour is formed by elliptic arcs. The influence of sweepback and contour upon the neutral point is shown.

Description: Tests of two 10-foot-diameter two-blade propellers which differed only in shank design have been made in the Langley 16-foot high-speed tunnel. The propellers are designated by their blade design numbers, NACA 10-(5)(08)-03, which had aerodynamically efficient airfoil shank sections, and NACA l0-(5)(08)-03R which had thick cylindrical shank sections typical of conventiona1 blades, The propellers mere tested on a 2000-horsepower dynamometer through a range of blade-angles from 20deg to 55deg at various rotational speeds and at airspeeds up to 496 miles per hour. The resultant tip speeds obtained simulate actual flight conditions, and the variation of air-stream Mach number with advance ratio is within the range of full-scale constant-speed propeller operation. Both propellers were very efficient, the maximum envelope efficiency being approximately 0,95 for the NACA 10-(5)(08)-03 propeller and about 5 percent less for the NACA 10-(5)(08)-03R propeller. Based on constant power and rotational speed, the efficiency of the NACA 10-(05)(08)-03 propeller was from 2.8 to 12 percent higher than that of the NACA 10-(5)(08)-03R propeller over a range of airspeeds from 225 to 450 miles per hour. The loss in maximum efficiency at the design blade angle for the NACA 10-(5)(08)-03 and 10-(5)(08)-03R propellers vas about 22 and 25 percent, respectively, for an increase in helical tip Mach number from 0.70 to 1.14.

Description: An investigation was made to determine the effects of changes in the amount and distribution of forebody and afterbody dead rise on the hydrodynamic resistance and spray characteristics of a 1/11-size model of the Bureau of Aeronautics design No. 22ADR class VPB airplane. The variations in dead rise within the range investigated had no significant effects on resistance or trim, free to trim, or on resistance or trimming moment, fixed in trim. The coordinates of the peaks of the bow-spray blisters, with reference to the model, were measured at low speeds, and it was found that the model with the low dead rise at the bow had the lowest blisters. The changes in position of the maximum dead rise of the afterbody had no effect on the bow-spray blister.

Description: Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The wing-alone tests and the effect of the various vertical-fin modifications, speed-brake modifications, and fuselage modifications on the aerodynamic characteristics in pitch and yaw are presented in the present paper with a limited analysis of the results. Also included are tuft studies of the flow for some of the modifications tested.

Description: Wind-tunnel tests on a 1/5-scale model of the Ryan XF2R airplane were conducted to determine the aerodynamic characteristics of the air intake for the front power plant, a General Electric TG-100 gas turbine, and to determine the stability and control characteristics of the airplane. The results indicated low-dynamic-pressure recover3- for the air intake to the TG-100 gas turbine ~rith the standard propeller in operation. Propeller cuffs were designed and tested for the purpose of imp~oving the dynamic-pressure recovery. Data obtained with the cuffs installed and the gap between the spinner an& the cuff sealed indicated a substantial gain in dynamic pressure recovery over that obtained with the standard propeller and with the cuffed propeller unsealed. Stability and control tests were conducted with the sealed cuffs installed on the propeller. The data from these tests indicated the following unsatisfactory characteristics for the airplane: 1. Marginal static longitudinal stability. 2. Inadequate directional stability and control. 3. Rudder-pedal-force reversal in the climb condition. 4. Negative dihedral effect in the power-on approach and wave-off conditions.

Description: An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of three deep-stepped planing-tail flying-boat hulls differing only in the amount of step fairing. The hulls were derived by increasing the unfaired step depth of a planing-tail hull of a previous aerodynamic investigation to a depth about 92 percent of the hull beam. Tests were also made on a transverse-stepped hull with an extended afterbody for the purpose of comparison and in order to extend and verify the results of a previous investigation. The investigation indicated that the extended afterbody hull had a minimum drag coefficient about the same as a conventional hull, 0.0066, and an angle-of-attack range for minimum drag coefficient of 0.0057 which was 14 percent less than the transverse stepped hull with extended afterbody; the hulls with step fairing had up to 44 percent less minimum drag coefficient than the transverse-stepped hull, or slightly more drag than a streamlined body having approximately the same length and volume. Longitudinal and lateral instability varied little with step fairing and was about the same as a conventional hull.

Description: The motion of different bodies imersed in liquid or gaseous media is accompanied by characteristic sound which is excited by the formation of unstable surfaces of separation behind the body, usually disintegrating into a system of discrete vortices(such as the Karman vortex street due to the flow about an infintely long rod, etc.).In the noise from fans,pumps,and similar machtnery, vortexnQif3eI?Yequently predominates. The purpose of this work is to elucidate certain questions of the dependence ofthis sound upon the aerodynamic parameters and the tip speed of the rotating rods,or blades. Although scme material is given below,insufficientto calculate the first rough approximation to the solution of this question,such as the mechanics of vortex formation,never the less certain conclusions maybe found of practical application for the reduction of noise from rotating blades.

Description: Tests were conducted to find the effects of compressibility on the longitudinal stability and control of a 1/7-scale semispan model of the Northrop YB-49 airplane. Lift, drag, pitching moment, and elevon hinge moments were measured and are presented in graphical form. The results show that, due to a loss of lift on the outboard portion of the wing, the longitudinal static stability decreased rapidly as the Mach numbers increased above 0.735 the model experienced a climbing moment at positive lift coefficients. Also, a longitudinal-control effectiveness began to decrease at a Mach number of about 0.725

Description: It is known that the compressibility shocks accompanying local or total supersonic flows lead to pronounced flow separations which result in unusually high energy losses on airplane wings, vanes, and in diffusers. These phenomena were investigated experimentally and theoretically.

Description: Calculations and test results are given about the feed-power requirement of airplanes with boundary-layer control. Curves and formulas for the rough estimate of pressure-loss and feed-power requirement are set up for the investigated arrangements which differ structurally and aerodynamically. According to these results the feed power for three different designs is calculated at the end of the report.