ALBERT

Description: Transport fuselage section drop tests provided useful information about the crash behavior of metal aircraft in preparation for a full-scale Boeing 720 controlled impact demonstration (CID). The fuselage sections have also provided an operational test environment for the data acquisition system designed for the CID test, and data for analysis and correlation with the DYCAST nonlinear finite-element program. The correlation of the DYCAST section model predictions was quite good for the total fuselage crushing deflection (22 to 24 inches predicted versus 24 to 26 inches measured), floor deformation, and accelerations for the floor and fuselage. The DYCAST seat and occupant model was adequate to approximate dynamic loading to the floor, but a more sophisticated model would be required for good correlation with dummy accelerations. Although a full-section model using only finite elements for the subfloor was desirable, constraints of time and computer resources limited the finite-element subfloor model to a two-frame model. Results from the two-frame model indicate that DYCAST can provide excellent correlation with experimental crash behavior of fuselage structure with a minimum of empirical force-deflection data representing structure in the analytical model.

Description: The dynamic behavior of aircraft fuselage structures subject to various impact conditions was investigated. An analytical model was developed based on a self-consistent finite element (CFE) formulation utilizing shell, curved beam, and stringer type elements. Equations of motion were formulated and linearized (i.e., for small displacements), although material nonlinearity was retained to treat local plastic deformation. The equations were solved using the implicit Newmark-Beta method with a frontal solver routine. Stiffened aluminum fuselage models were also tested in free flight using the UTIAS pendulum crash test facility. Data were obtained on dynamic strains, g-loads, and transient deformations (using high speed photography in the latter case) during the impact process. Correlations between tests and predicted results are presented, together with computer graphics, based on the CFE model. These results include level and oblique angle impacts as well as the free-flight crash test. Comparisons with a hybrid, lumped mass finite element computer model demonstrate that the CFE formulation provides the test overall agreement with impact test data for comparable computing costs.

Description: The multiobjective programming techniques are important in the design of complex structural systems whose quality depends generally on a number of different and often conflicting objective functions which cannot be combined into a single design objective. The applicability of multiobjective optimization techniques is studied with reference to simple design problems. Specifically, the parameter optimization of a cantilever beam with a tip mass and a three-degree-of-freedom vabration isolation system and the trajectory optimization of a cantilever beam are considered. The solutions of these multicriteria design problems are attempted by using global criterion, utility function, game theory, goal programming, goal attainment, bounded objective function, and lexicographic methods. It has been observed that the game theory approach required the maximum computational effort, but it yielded better optimum solutions with proper balance of the various objective functions in all the cases.

Description: There are a number of helicopter design problems that are well suited to applications of numerical design optimization techniques. Adequate implementation of this technology will provide high pay-offs. There are a number of numerical optimization programs available, and there are many excellent response/performance analysis programs developed or being developed. But integration of these programs in a form that is usable in the design phase should be recognized as important. It is also necessary to attract the attention of engineers engaged in the development of analysis capabilities and to make them aware that analysis capabilities are much more powerful if integrated into design oriented codes. Frequently, the shortcoming of analysis capabilities are revealed by coupling them with an optimization code. Most of the published work has addressed problems in preliminary system design, rotor system/blade design or airframe design. Very few published results were found in acoustics, aerodynamics and control system design. Currently major efforts are focused on vibration reduction, and aerodynamics/acoustics applications appear to be growing fast. The development of a computer program system to integrate the multiple disciplines required in helicopter design with numerical optimization technique is needed. Activities in Britain, Germany and Poland are identified, but no published results from France, Italy, the USSR or Japan were found.

Description: An optimization study was performed to develop a minimum weight spreader bar to allow two helicopters to lift the same payload. With this arrangement, the maximum payload that can be lifted is almost doubled without the expense of designing and building a new helicopter. The concept has had some limited use by civil helicopter operators using small helicopters and has been demonstrated in large scale by two CH-54's which successfully lifted a total load of 20 ton. To this point, rather heavy available beams or tower structures have been used for the spreader bar. Since the weight of the bar not only detracts from payload but also adds to the logistics problem, there are more than the usual incentives to minimize weight. Since the design requirement is for classic beam column with uniform side loads resulting from bar weight and aerodynamic drag, the design problem is particularly amenable to optimization. A study has been performed at Sikorsky to establish the minimum weight for a spreader bar sized to carry a load equal to the capacity of two Army BLACK HAWK helicopters. Toward this end, a computer program was written to analyze the spreader bar deflections and stresses and coupled to the NASA developed CONMIN optimization routines.

Description: The optimization approach discussed is part of an ongoing effort to develop a general automated procedure for rotor blade design. This procedure can be used to determine the necessary geometric, structural, and material properties of a rotor system to achieve desired objectives relating to vibration, stress, and aerodynamic performance. The approach used for helicopter vibration is emphasized. Based on analytical studies performed at the United Technologies Research Center (UTRC), a simplified vibration analysis was developed to be used in conjunction with a forced response analysis in the optimization process. This simplified analysis improves the efficiency of the design process significantly. Results of applying this approach to the design of an existing rotor blade model are presented.

Description: This discussion summarizes the effort conducted by the BHTI Human Factors and Cockpit Arrangement group for a study and design of the integration of a cockpit control system for the AH 1T (TOW). The resulting design is a culmination of studies that were conducted using the existing configuration as a baseline and complementing it with new equipment and subsystems that fulfill the attack helicopter requirements for the foreseeable future. Of primary concern was the requirement to add a missile control system, with secondary considerations for improved NOE and night operations. In addition, growth capabilities for improved target acquisition, weapons delivery, and precise navigation was considered. Along with the addition of new equipment, the aircraft was assumed to have a central multiplex data bus system for information transfer throughout the aircraft and its subsystems.

Description: Nine research areas that are most critical to the issue of cockpits for the single pilot are discussed. Helicopter are addressed in this report. They are as follows: (1) automation priority issues; (2) increased complexity of systems; (3) cockpit workload highest in navigation; (4) auto hover and flight trim controls; (5) voice technology in integrated form; (6) systems must have visual and auditory declutter modes; (7) cockpit should be designed to be NBC resistant; and (8) considerations for spillover to civilian public service.

Description: Fundamental development issues, system requirements and improvements are reported for the HH-60D night hawk helicopter. The HH-60D mission requirements are for combat search and rescue (aerospace rescue and recovery service user based at Scott AFB) and special operations (special operations forces based at Hurlburt AFB). Cockpit design, computer architecture and software are described in detail.

Description: An analytical study was performed in order to assess relative performance and economic factors involved with alternative advanced fuel systems for future commercial aircraft operating with broad property fuels. Significant results, with emphasis on design practicality from the engine manufacturer' standpoint, are highlighted. Several advanced fuel systems were modeled to determine as accurately as possible the relative merits of each system from the standpoint of compatibility with broad property fuel. Freezing point, thermal stability, and lubricity were key property issues. A computer model was formulated to determine the investment incentive for each system. Results are given.

Description: Several problems related to the aeroelastic/aerodynamic optimization of a high speed helicopter compound rotor are discussed. The helicopter fuselage vibration problem, the effects of fuselage vibrations, the source of external and periodic air loads, typical airfoil environments and configurations, rotor dynamics, vibration reduction, and requirements for the rotor design optimization analysis are among the topics covered.

Description: Formal mathematical programing was applied to the aerodynamic rotor blade design process. The approach is to couple hover and forward flight analysis programs with the general-purpose optimization program CONMIN to determine the blade taper ratio, percent taper, twist distribution, and solidity which minimize the horsepower required at hover while meeting constraints on forward flight performance. Designs obtained using this approach for the blade of a representative Army helicopter compare well with those obtained using a conventional approach involving personnel-intensive parametric studies. Results from the present method can be obtained in 2 days as compared to 5 weeks required by the conventional procedure. Also the systematic manipulation of the design variables by the optimization procedure minimizes the need for the researcher to have a vast body of past experience and data in determining the influence of a design change on the performance.

Description: As a user of devices and procedures for lightning protection, the author is asking the lightning research community for cookbook recipes to help him solve his problems. He is lamenting that realistic devices are scarce and that his mission does not allow him the time nor the wherewithal to bridge the gap between research and applications. A few case histories are presented. In return for their help he is offering researchers a key to lightning technology--the use of the Eastern Test Range and its extensive resources as a proving ground for their experiment in the lightning capital of the United States. A current example is given--a joint lightning characterization project to take place there. Typical resources are listed.

Description: The main Army Helicopter Improvement Program (AHIP) mission is to navigate precisely, locate targets accurately, communicate their position to other battlefield elements, and to designate them for laser guided weapons. The onboard navigation and mast-mounted sight (MMS) avionics enable accurate tracking of current aircraft position and subsequent target location. The AHIP crewstation development was based on extensive mission/task analysis, function allocation, total system design, and test and verification. The avionics requirements to meet the mission was limited by the existing aircraft structural and performance characteristics and resultant space, weight, and power restrictions. These limitations and night operations requirement led to the use of night vision goggles. The combination of these requirements and limitations dictated an integrated control/display approach using multifunction displays and controls.

Description: The interactions between the design and operation of aircraft fuel systems and the properties of alternative aircraft fuels are discussed. An overview of fuels system research and technology in terms of its rationale, its progress, and future plans is given. The measurement of ambient air temperatures for a wide range of seasonal and geographic variations, design studies on the use of fuels with increased as well as conventional freezing temperatures, the evaluation of fuel heating systems, and the low temperature behavior of fuels are among the topics discussed.

Description: Several examples of spacecraft systems fires are examined. Much of the design, manufacture, inspection, test, and operation of current high pressure oxygen components and systems has been driven by weight, cost, functional, and schedule requirements. As a result, little coordination has been expended on design for safe operation. While the number of oxygen related fires has not been large, their cost, including program losses and delays, has been very large. Most of these failures need not have occurred.

Description: The results of a study assessing the impact of using jet fuel with relaxed specification properties on an aircraft fuel system are given. The study objectives were to identify credible values for specific fuel properties which might be relaxed, to evolve advanced fuel system designs for airframe and engines which would permit use of the specified relaxed properties fuels, and to evaluate performance of the candidate advanced fuel systems and the relaxed property fuels in a typical transport aircraft. The study used, as a baseline, the fuel system incorporated in the Lockheed Tristar. This aircraft is powered by three RB.211-524 Rolls-Royce engines and incorporates a Pratt and Whitney ST6C-421 auxiliary power unit for engine starting and inflight emergency electrical power. The fuel property limits examined are compared with commercial Jet A kerosene and the NASA RFP fuel properties. A screening of these properties established that a higher freezing point and a lower thermal stability would impact fuel system design more significantly than any of the other property changes. Three candidate fuel systems which combine the ability to operate with fuels having both a high freeze point and a low thermal stability are described. All candidates employ bleed air to melt fuel freeze-out prior to starting the APU or an inoperable engine. The effects of incorporating these systems on aircraft weight and engine specific fuel consumption are given.

Description: Based on initial results obtained from the performance optimization code, a number of observations can be made regarding the utility of optimization codes in supporting design of rotors for improved performance. (1) The primary objective of improving the productivity and responsiveness of current design methods can be met. (2) The use of optimization allows the designer to consider a wider range of design variables in a greatly compressed time period. (3) Optimization requires the user to carefully define his problem to avoid unproductive use of computer resources. (4) Optimization will increase the burden on the analyst to validate designs and to improve the accuracy of analysis methods. (5) Direct calculation of finite difference derivatives by the optimizer was not prohibitive for this application but was expensive. Approximate analysis in some form would be considered to improve program response time. (6) Program developement is not complete and will continue to evolve to integrate new analysis methods, design problems, and alternate optimizer options.

Description: The collective character of carbon exchanges between the atmosphere and other pools is partially revealed by comparing the record of CO2 concentration beginning in 1958 with estimates of the releases from fossil fuels during this period. In analyzing the secular increase in CO2 concentration induced by fossil fuel use, the atmosphere is generally treated as a single well-mixed reservoir; however, to study finer structure in the CO2 records, the influence of atmospheric circulation must be more carefully considered. The rate of carbon uptake by the oceans, the primary sink for fossil fuel CO2, is assessed more reliably than influences on the atmosphere due to interactions with other pools. Models of the global carbon cycle are being substantially refined while data that reflect the response of the cycle to fossil fuel use and other perturbations are being extended.

Description: A statistical correlation technique is applied to the retrieval of vertical moisture profiles under clear-sky conditions from down-looking radiometric measurements of atmospheric radiation at microwave wavelengths. For a given set of channels, the method selects the optimum radiometric channels for estimating water vapor at specific pressure levels between the surface and 300 mb. The water vapor mixing ratio at these pressure levels is then calculated from a linear combination of the selected channel brightness temperatures. To test its validity the algorithm was applied, in a numerical experiment, to fifty independent tropical radiosondes. The rms absolute deviation of the estimated moisture profiles from the actual profiles was comparable to that obtained using an iterative retrieval method reported earlier. The statistical method, however, requires several orders of magnitude less computer time than the iterative method; it is suitable for high speed processing of large amounts of data.

Description: The application of an experimental flight test maneuver autopilot test technique for collecting aerodynamic and structural flight research data on a highly maneuverable aircraft is described in this paper. This technique, which was developed to increase the quality and quantity of data obtained during flight test, was applied to the highly maneuverable aircraft technology (HiMAT) vehicle. A primary flight experiment was to verify the design techniques used to develop the HiMAT aerodynamics and structures. This required the performance of maneuvers for collection of large quantities of high-quality pressure distribution, loads, and wing and canard deflection data. Flight data obtained while executing these research maneuvers are presented to demonstrate the effectiveness of this new technique.

Description: The Andre et al. (1976, 1978) third-order closure model, in which the time rate of change terms, the relaxation and rapid effects for pressure-related terms, and the clipping approximation are used along with the quasi-normal closure, is invoked in the study of turbulence in a cloudy layer that is radiatively cooled from above. A spurious oscillation whose greatest amplitude lies near the inversion is shown by analysis to arise from the mean gradient and buoyancy terms of the triple-moment equations. An attempt is made to damp the oscillation through the introduction of diffusion terms into the triple-moment equations. The results obtained are noted to be sensitive to the ad hoc eddy coefficient applied in the third-moment equations.

Description: Space-time mapping of VHF sources from four severe storms on June 19, 1980 reveals that lightning processes for cloud-to-ground (CG) and large intracloud (IC) flashes are confined to an altitude below about 10 km and closely associated with the central regions of high reflectivity. Another class of IC flashes produces a splattering of sources within the storms' main electrically active volumes and also within the large divergent wind canopy aloft. There is no apparent temporal association between the small high altitude IC flashes that occur almost continuously and the large IC and CG flashes that occur sporadically in the lower portions of storms.

Description: A variational principle for time dependent diffusion problems is presented and is demonstrated by applying it to simple seasonal climate models. Two cases are treated. The first, a North-Coakley-type model with constant properties, is used as a tutorial example for the application of the technique. For the second case, heat capacity and thermal conductivity are considered to be latitude dependent in order to treat the effects of land/ocean distribution on the seasonal temperature distribution over the earth. The variational equations are derived and approximate analytical solutions are developed which delineate the influences of the physical asymmetries of the hemispheres in producing an asymmetric annual cycle.

Description: Lorenz (1969) has considered the possibility that an atmospheric circulation pattern might recur, taking into account the definition of a pair of analogous flows or 'analogs'. The present investigation is concerned with a search of time series of Northern Hemisphere wintertime geopotential heights for possible analogs. Attention is given to data and analysis procedure, analog quality, and error growth rates. The obtained results imply that the found analogs are not a useful tool for forecasting the evolution of the midlatitude flow on time scales of several days. It is pointed out, however, that the negative results should not be extended to other applications of analog forecasting.

Description: Rotorcraft noise includes turbofan engine noise components, as well as noise from the main and tail rotors that is conditioned by the aircraft's various operational modes. Both of the rotors generate loading noise and broadband noise. Another noise contributor is blade/vortex interaction noise, which results when shed vortices are encountered by a following blade, releasing impulsive acoustic energy. Attention is presently given to the experimental and developmental initiatives to be made by a NASA/industry five-year program that began in 1983. Aeroacoustic data acquired from experiments conducted in NASA facilities can be used in the development of empirical noise prediction methods, in the improvement of existing noise prediction methodology, in the evaluation of proposed reduced noise designs, and in the establishment of useful scaling relationships for selected noise-generating mechanisms.

Description: Simple climate models which invoke diffusive heat transport and ice cap albedo feedback have equilibrium solutions with no stable ice cap smaller than a radius of about 20 deg on a great circle. Attention is presently given to a solution of this phenomenon which is physically appealing. The ice-free solution has a thermal minimum, and if the minimum temperature is just above the critical value for ice formation, then the artificial addition of a patch of ice leads to a widespread depression of the temperature below the critical freezing temperature. A second stable solution will then exist whose spatial extent is determined by the range of the influence function of a point sink of heat, due to the albedo shift in the patch.

Description: A comment is presented on a recent paper by Pagnotti and Bosart (1984) which contrasted different forcing mechanisms for weak and strong cyclones along the east coast of the U.S., and Bosart replies. The comment argues that the paper did not give a clear definition of 'weak' upper-level forcing and did not provide sufficient evidence to support its claim that the return branch of transverse circulations may be coupled to the middle as opposed to the lower troposphere.

Description: A fully nonlinear numerical model of the point jet barotropic instability is used to test and confirm the hypothesis that the magnitude of the wave vorticity does not exceed the magnitude of the initial shear. This result arises directly from the local conservation of vorticity following a parcel and the fact that unstable waves are principally confined to the region where the zonal mean vorticity can be smoothed by the wave so as to eliminate the instability. Comparisons are made between fully nonlinear and quasi-linear models of the point jet instability and their tracer transport properties. Differences become particularly evident after wave saturation. The most important effect neglected by the wave-mean flow model appears to be the advection of wave vorticity by the most unstable mode. However, as equilibration of the instability proceeds, the globally averaged properties of both models are found to be similar.

Description: We calculate the seasonal changes that are largely associated with the half-yearly wave, autocorrelation functions, and the mean planetary waves in the monthly mean sea level pressure from two data sources. One covers the period from 1951 to 1958 (from the South African Weather Bureau) and the other the period from 1972 to 1980 (from the Australian Bureau of Meteorology). Thirty years of data from stations over the southern hemisphere are used to assess the reliability of the differences between the two periods that the grid-point data show. These differences are especially large over the Atlantic Ocean and the Pacific Ocean. The station data confirm the changes between the two periods and thus the observed differences in the mean waves, which are especially large for wave number 3.

Description: The cloud observation archive from the NASA Global Atmospheric Sampling Program (GASP) is analyzed in order to derive the probability of cloud encounter at altitudes normally flown by commercial airliners, for application to a determination of the feasability of Laminar Flow Control (LFC) on long-range routes. The probability of cloud encounter is found to vary significantly with season. Several meteorological circulation features are apparent in the latitudinal distribution of cloud cover. The cloud encounter data are shown to be consistent with the classical midlatitude cyclone model with more clouds encountered in highs than in lows. Aircraft measurements of route-averaged time-in-clouds fit a gamma probability distribution model which is applied to estimate the probability of extended cloud encounter, and the associated loss of LFC effectiveness along seven high-density routes. The probability is demonstrated to be low.

Description: Attention is given to physical principles that affect the determination of atmospheric temperature profiles from observations of outgoing IR and microwave radiation. Simultaneous analysis of IR and microwave observations enhances observations in each spectral region. While IR soundings have higher sensitivity to lower tropospheric temperatures, ground temperatures, and sea surface temperatures, microwave observations are not only more suited to stratospheric sounding but are sensitive to snow and ice cover. They significantly aid correction of IR observations for cloud effects. Because effective cloud parameters and snow and ice cover can be inferred from the observations, 'temperature sounders' also yield data for a number of important climatic parameters.

Description: The influence of soil moisture on the persistence of an ongoing drought was investigated. The case study of drought of the summer of 1980 was selected. The difference in the simulation of two identical twin runs: one with the climatological normal soil moisture and the other with anomalous soil moisture for drought conditions, were examined on the mean monthly circulation. It is found that a reduction in soil moisture did produce a corresponding reduction in precipitation. The pattern of the rainfall anomaly however, was not identical to the soil moisture (evapotranspiration) anomaly but had a good resemblance with observations.

Description: During the Northern summer, sporadic outbreaks of wind borne Saharan dust are carried out over the Atlantic by the tropical easterlies. Optical depths due to the dust can reach 3 near the African coast, and the dust cloud can be detected as far west as the Caribbean Sea (Carlson, 1979). In order to obtain insight into the possible effects of Saharan dust on the weather and climate of North Africa and the tropical Atlantic Ocean, simulation experiments have been performed with the Climate Model of the Goddard Laboratory for Atmospheric Sciences. The most recent version of the model is described by Randall (1982). The model produces realistic simulations of many aspects of the observed climate and its seasonal variation.

Description: The sensitivity of climate which may have a local maximum as the ice cap passes through a midlatitude region where the atmosphere's transport efficiency varies strongly with latitude is examined. This behavior, found in a two level primitive equations climate model forced with annual mean insolation, was reproduced in an energy balance model (EBM) by making the diffusion coefficient a function of latitude. The two level seasonally varying EBM was applied and the global mean surface temperature vs. solar constant for this model are shown and two regions of enhanced sensitivity appear. The snowcover distributions around the year for three cases are shown.

Description: The role of transient eddies in maintaining the observed local seasonal mean atmospheric circulation was investigated by examining the time-averaged momentum balances and omega equation, using seasonal statistics calculated from daily operational analyses by the European Centre for Medium Range Weather Forecasts. While both the Northern and Southern Hemispheres and several seasons were studied, emphasis was placed upon the Northern Hemisphere during December 1981-February 1982. The results showed that transient eddies played a secondary role in the seasonal mean zonal momentum budget and in the forcing of seasonal mean vertical and a geostrophic motion.

Description: Contemporaneous correlations between geopotential heights on a given pressure surface at widely separated points on Earth, commonly referred to as teleconnections, are calculated from monthly mean sea level pressure and 500 mb geopotential height analyses for the Southern Hemisphere for five-month winter and summer seasons. During summer (November-March), anomalies over the three continents occur out of phase with anomalies over the subtropical oceans and in a wavenumber 3 pattern over the Southern Ocean near 55 deg S. The subtropical part of the pattern appears largely associated with the interannual variation of the seasonal cycle and annual mean. In winter (May-September) 500 mb geopotential heights over Africa exhibit positive correlations with heights over South America and the central South Pacific near New Zealand and negative correlations with height over the Southern Ocean. A striking wavenumber three pattern is apparent which shows the correlation of 500 mb geopotential height anomalies with 500 mb anomalies at 50 deg S, 95 deg E during winter. The strong positive correlations between 50 deg S, 95 E and 58 deg S, 150 deg W and 38 deg S, 15 deg W contrast with negative correlations over Antarctica and in low latitudes. Time variations in a similar pattern in sea level pressure are in phase with variations in the 500 mb pattern, suggesting an equivalent barotropic structure.

Description: The incorporation of observed zonal topography in a barotropic nonlinear channel model is discussed. The model is then extended to explain the regional features of blocking by employing a two scale method to allow small slow variations of the momentum (zonal) driving.

Description: Stratus and stratocumulus cloud sheets which are among the most common cloud types over the world are discussed. They are characteristic of the undisturbed subtropical marine boundary layer over the eastern oceans, where cool water and large scale sinking motion suppress penetrative cumulus convection. They also occur over the Arctic Ocean, particularly in summer, and behind cold outbreaks over the western oceans in winter. Observational studies were conducted and further observations are planned.

Description: A numerical simulation study, using the current GLAS climate GCM, was carried out to examine the influence of low bulk aerodynamic drag parameter in the deserts. The results illustrate the importance of yet another feedback effect of a desert on itself, that is produced by the reduction in surface roughness height of land once the vegetation dies and desert forms. Apart from affecting the moisture convergence, low bulk transport coefficients of a desert lead to enhanced longwave cooling and sinking which together reduce precipitation by Charney's (1975) mechanism. Thus, this effect, together with albedo and soil moisture influence, perpetuate a desert condition through its geophysical feedback effect. The study further suggests that man made deserts is a viable hypothesis.

Description: Seasonal statistics calculated from daily operational analyses by the European Centre for Medium Range Weather Forecasts for December 1980 - February 1981 (season 1) and December 1981 - February 1982 (season 2) were used to contrast the two seasonal mean circulation patterns present in the Northern Hemisphere and to investigate possible causes for the differences. The vertically averaged seasonal mean zonal wind and E-vector, a measure of the anisotropy of the transient eddies over the Pacific is shown for season 1 and season 2. The pattern in season 2, but not season 1, resembles that found in a modeling study of barotropic instability. One possible explanation for the differences between season 1 and 2 is a weak change in tropical heating associated with the southern oscillation, the effect of which in midlatitude was amplified by the occurrence of barotropic instability over the Pacific in season 2, but not season 1.

Description: An ensemble approach is applied to Planetary Boundary Layer (PBL) calculations with the bulk Richardson number identified as the key parameter. An ensemble averaging calculation was carried out to rederive the bulk friction and heat transport coefficients for the mean condition. Two simulations are carried out and compared. Significant differences in PBL fluxes low level cloudiness, land surface roughness heights, and surface evaporation are noted between the modified and unmodified simulations. Modifications to the model were: (1) the relationship between actual and potential Effective Temperature (ET) to accord with Sud and Fennessy (1982); (2) maximum permissible instantaneous ET at any time is 1.5 mm per hr; (3) moisture distribution in low level cumulus convection to be consistent with no precipitation; (4) appearance of supersaturation clouds to be consistent with supersaturation condition at that level; (5) invoking a simple function for stomatal diffusion effect in the ET calculation.

Description: Several recent helicopter vibration reduction research programs are described. Results of studies of blade design parameters in rotor vibratory response and of an advanced blade design for reduced vibration are examined. An optimization approach to develop a general automated procedure for rotor blade design is described, and analytical results for an articulated rotor operating at a steady 160 kt flight condition are reported. The use of a self-adaptive controller to implement higher harmonic control in closed-loop fashion is addressed, and a computer simulation used to evaluate and compare the performance of alternative algorithms included in the generic active controller is discussed. Results are presented for steady level flight conditions, short-duration maneuvers, blade stresses and rotor performance, blade-appended aeroelastic devices, vibratory airloads, wake-induced blade airloads, and airloads from blade motions, the interaction of rotor and fuselage, and the interaction of rotor and empennage.

Description: The method proposed by Pandey et al. (1983) for estimating the temperature differential and thickness of clouds from microwave data obtained with the scanning multichannel microwave radiometers of the Seasat and Nimbus-7 satellites is examined critically. It is pointed out that both the thicknesses and the temperature differentials derived from them may not be meaningful unless accurate measurements of cloud-top height (from IR radiometry) and reliable data on liquid-water content are available. It is suggested that the good fits obtained in generating regression coefficients for the proposed method may be artifacts of the fixed or limited-range liquid-water densities of the cloud models used. With respect to cloud-top height, the need to quantify and account for differences in the fields of view and spatial resolutions of the IR and microwave radiometers, as undertaken for the case of precipitating clouds by Yeh and Liou (1983), is stressed.

Description: Infrared and visible imagery from VAS are used to delineate mid- and lower-tropospheric moisture fields for a variety of severe storm cases in the southern and central United States. The ability of sequences of images to isolate areas of large negative vertical moisture gradients and apparent convective instability prior to the onset of convective storms is assessed. A variety of image combination procedures are used to deduce the stability fields which are then compared with the available radiosonde data. The results for several severe storm cases indicate that VAS can detect mid- and low-level mesoscale water vapor fields as distinct radiometric signals. The VAS imagery shows a strong tendency for thunderstorms to develop along the edges of bands of midlevel dryness as they overtake either preexisting or developing low-level moisture maxima. Image sequences depict the speed with which deep moist and dry layers can develop and move.

Description: The reflected fluxes of stratocumulus cloud fields are calculated as a function of sky cover aspect ratio and cloud shape. In order to obtain a better fit with general circulation models (GCMs), cloud liquid water volume values were kept invariant relative to cloud shape. On the basis of the required accuracy of the Earth Radiation Budget Experiment (ERBE), an order of magnitude value of 10 W per sq m was used to estimate the difference between plane-parallel and broken cloudiness reflected fluxes. An empirical relationship for effective cloud cover at a solar zenith angle of 60 deg is derived. The relationship allows for the accurate computation of broken cloud field reflected fluxes using plane-parallel calculations. It is predicted that more accurate estimates of broken cloud field radiative properties may be possible in the future.

Description: Results obtained with a mixed layer model are used to study the dynamics of stratocumulus formation and dissipation in subtropical marine stratocumulus cloud regimes. The model used allows entrainment to be driven by shear as well as buoyancy, and includes a very crude parameterization of the partial blackness of thin cloud layers. Model results show that for some values of the large-scale divergence there are three equilibrium mixed layer structures, two of which are stable. One of the stable equilibria is cloudy, deep, and buoyancy-driven, while the other is clear, shallow, and shear-driven. It is found that as a result of hysteresis effects a transient increase in the large-scale divergence can produce a long-lasting break in the clouds.

Description: Some of the motivations for constructing models of the middle atmosphere circulation are given. These are as follows: (1) to provide a better understanding of middle atmosphere dynamics; (2) to study the coupling of middle atmosphere dynamics with radiation and chemistry; (3) to study the sensitivity of tropospheric climate modeling and/or weather forecasting to changes in the middle atmosphere; (4) to better understand the limitations of more simplified models; (5) to supply a proxy for atmospheric data for diagnostic analysis; and finally, (6) for forecast-analysis of data. Different types of models are discussed in relation to their anticipated use. Various model simplifications, such as using the quasi-geostrophic set of equations and simplified radiative transfer, are discussed as are some of the consequences of these simplifications. Some of the accomplishments of middle atmosphere circulation modeling are presented as are some of the difficulties in existing models. Finally, some of the problems in constructing and verifying middle atmosphere circulation models are discussed.

Description: Under a substantial range of realistic conditions, stratocumulus cloud top entrainment is noted to either deepen an existing cloud layer or produce clouds in an unsaturated mixed layer, though the entrained air is warmer and drier than the mixed-layer air. These results, which apply irrespective of entrainment rate-determining mechanism, imply that the cloud top entrainment instability discussed by Randall (1980) and Deardorff (1980) does not necessarily destroy a layer cloud. Examples are given which include soundings, marine layer data, and simulation results produced by the UCLA general circulation model.

Description: An intercomparison between radiative parameters determined from visible and infrared channels of the Meteosat-1 and GOES-2 geosynchronous satellites has been carried out using data obtained over the central Atlantic Ocean for 5 November 1978. Hourly visible-infrared measurement pairs at a nominal resolution of 5 km (Meteosat) or 8 km (GOES) have been stored in 1 deg x 1 deg longitude-latitude regions. For the infrared intercomparisons, the GOES 11.5 micron radiance has been compared to Meteosat infrared counts. The scatter in partly cloudy regions is interpreted as being caused by meteorological differences arising from differences in measurement time between the two data sets. For the visible intercomparison, the GOES measurements for clear and cloudy scenes have first been converted with the aid of scene-dependent angular reflectance and albedo models to estimates of the filtered shortwave radiance that GOES would have measured had it been in the Meteosat position. This value has then been compared to Meteosat counts for the shortwave channel. The results indicate that earlier Meteosat calibrations made from airplane overflights of a limited variety of surfaces are applicable to much larger areas of cloud and ocean.

Description: A detailed description of the goals and methodology of the First International Satellite Cloud Cover Project Regional Experiment (FIRE) is presented. The purpose of the experiment is to develop physical models and parameterizations of fractional cloud cover over the Pacific Basin. In order to determine fractional cloud cover parameters, satellite observations by radar and lidar instruments will be combined with in situ measurements of the cloud-capped marine boundary layer. A description of a candidate experiment for the program is presented, and some general problems connected with the statistical characterization of satellite imagery are discussed.

Description: The planetary-scale components of the extratropical Northern Hemisphere troposphere-stratosphere 1973-74 winter circulation are diagnosed using separate time-mean temperature fields based on radiosonde and satellite observations. Meridional cross-sections of zonal wind together with, for zonal wavenumbers 1, 2 and 3, the streamfunction amplitude, phase and Eliassen-Palm flux are displayed, with the relative accuracy of the satellite-derived diagnostics assessed through comparison with the 'ground-truth' radiosonde information. The satellite and radiosonde diagnostics compare most favourably in terms of zonal wind speed and shear, direction of wave propagation and meridional wave structure - all of which are closely related to the differential properties of the atmospheric temperature field. The intensity of the satellite-derived patterns of tropospheric wave propagation is underestimated due to the effects of spatial smoothing and residual cloud contamination present in the satellite radiance measurements.

Description: A multi-level, sigma coordinate, primitive equation atmospheric model has been utilized to study both the tropical and extratropical response to an isolated region of steady thermal forcing in the tropics. The nonlinear response during the first 28 days of the simulation is described. The response can be generally characterized by two distinct components. The first component is a quasi-stationary disturbance which extends eastward and poleward away from the source region along a 'great circle' path. The structure of this disturbance is essentially barotropic away from the source region. The second component is a growing baroclinic wave propagating zonally at mid-latitudes. Significantly, this disturbance is apparently the result of baroclinic instability induced by the quasi-stationary wavetrain. The discussion is predominantly heuristic in form and relies heavily on graphical presentation and quasi-geostrophic theory to interpret the response and individual components of the thermodynamic energy and momentum equations.

Description: The X-29 experimental aircraft, which is a technology integration and evaluation platform for such features as static longitudinal instability, sweptforward wings and three-surface longitudinal control, offers an opportunity to validate the entire aircrft design process through careful correlation and comparison of flight test results with wind tunnel results and design predictions. Attention is presently given to the design features of the aircraft, which encompass supercritical airfoils, digital flight control, and aeroelastically tailored composite wings, as well as to the flight test program that was formulated to investigate the interactions and relative merits of these design features, in light of data gathered by carefully positioned sensors.

Description: The geographical distribution of the annual mean and the annual cycle in surface temperature and satellite-observed IR is examined, and the spherical harmonic representation of the data fields is exploited to demonstrate how variances and covariances are dominated by the largest space and time scales. The geographical distribution of the annual cycle in the T and IR fields is explored; the strong imprint of the continents in both is clearly evident. The influence of the cloudiness of seasonal precipitation regimes on the IR annual cycle is also quite striking, especially over the subtropics. Analysis of the data shows that the simple form IR = A+BT (with A = 204 W/sq m and B = 1.93 W/sq m/K) explains 90 percent of the area-weighted variance in the annual mean and annual cycle of the zonally averaged IR field.

Description: Lindzen's model of gravity wave breaking is shown to be inconsistent with the process of convective adjustment and associated turbulent outbreak. The K-theory turbulent diffusion model used by Lindzen implies a spatially uniform turbulent field which is not in agreement with the fact that gravity wave saturation and the associated convection produce turbulence only in restricted zones. The Lindzen model may be corrected to some extent by taking the turbulent Prandtl number for a diffusion acting on the wave itself to be very large. The eddy diffusion coefficients computed by Lindzen then become a factor of 2 larger and eddy transports of heat and constituents by wave fields vanish to first order.

Description: A program of experimental and analytical research has been performed to demonstrate the effects of rotor and fuselage design parameters on rotor in-plane stability, including aeromechanical stability. The experimental data were obtained from hover and wind-tunnel tests of a scaled advanced bearingless main rotor model. Both isolated-rotor and free-hub conditions were tested. Test parameters included blade built-in cone and sweep angles; rotor inplane structural stiffness and damping; pitch link stiffness and location; and fuselage natural frequency, damping, and inertia. The results show that rotor blade structural damping is one of the most influential design parameters in obtaining acceptable aeromechanical stability margins. Other parameters, such as blade cone angle, pitch link location (rotor delta 3) and anisotropic hub damper configurations, may be used to improve stability margins, but their individual effects are subtle.

Description: The published temperature changes produced in general circulation model simulations of CO2 induced climate modification are used to compute the top of the atmosphere, clear sky outgoing infrared radiance changes expected for doubled CO2. A significant wavenumber shift is produced, with less radiance emerging in the 500-800 per cm (20.0-12.5 micron) CO2 band and with more emerging in the 800-1200 per cm (12.5-8.3 micron) window. The effect varies greatly with latitude. The radiance shift in the 2300 per cm (4.3 micron) region is of the order of 10-30 percent for doubled CO2. It is suggested that the 2300 per cm region be carefully monitored as an aid in detecting the climatic effects of increasing CO2. The change in the wavenumber-integrated radiant exitance is at most a few percent.

Description: Measurements of broadband spectral absorption of solar radiation by the Arctic atmosphere during haze events are reported. A preliminary analysis of the data indicates that large changes occur in the radiative transfer processes in the Arctic during haze events. For example, the planetary albedo is estimated to increase by 2.5 percent over the ocean and to decrease by 9 percent over the ice cap. Changes of such magnitude in the radiative parameters have the potential for significant climatic effects. The need for further experimental and modeling efforts is emphasized.

Description: The Hadley cell is involved in the energy, momentum and moisture budgets in the atmosphere; it may be expected to change as sources and sinks of these quantities are altered due to climate perturbations. The nature of the Hadley cell change is complicated since alterations in one budget generally result in alterations in the others. Thus, Hadley cell sensitivity needs to be explored in an interactive system. In the GISS GCM (model I), a number of experiments are performed in which physical processes in each of the three budgets are omitted, the system adjusts, and the resultant circulation is compared to that of the control run. This procedure highlights which effects are most important and reveals the nature of the various interactions. The results emphasize the wide variety of processes that appear capable of influencing the mean circulation. The intensity of the circulation is related to the coherence of the thermal forcing, and to the thermal opacity of the atmosphere. When all frictional forcing is removed, the circulation is restricted to the equatorial region. The latitudinal extent appears to be controlled primarily by eddy processes (Ferrel cell intensity). The implications for climate modeling and climate projections (e.g. rainfall changes) are discussed.

Description: It is pointed out that studies of the entraining planetary boundary layer (PBL) have generally emphasized the role of buoyancy fluxes in driving entrainment. The buoyancy flux is proportional to the rate of conversion of the potential energy of the mean flow into the kinetic energy of the turbulence. It is not unusual for conversion to proceed in both directions simultaneously. This occurs, for instance, in both clear and cloudy convective mixed layers which are capped by inversions. A partitioning of the net conversion into positive parts, generating turbulence kinetic energy (TKE), and negative parts (TKE-consuming), would make it possible to include the positive part in the gross production rate, and closure would be achieved. Three different approaches to partitioning have been proposed. The present investigation is concerned with a comparison of the three partitioning theories. Particular attention is given to the cloud-topped mixed layer because in this case the differences between two partitioning approaches are most apparent.

Description: Previously cited in issue 12, p. 1701, Accession no. A83-29806

Description: Previously cited in issue 12, p. 1702, Accession no. A83-29860

Description: The need for numerical design optimization of naval structures is discussed. The complexity of problems that arise due to the significant roles played by three major disciplines, i.e., structural mechanics, acoustics, and hydrodynamics are discussed. A major computer software effort that has recently begun at the David W. Taylor Naval Ship R&D Center to accommodate large multidisciplinary analyses is also described. In addition to primarily facilitating, via the use of data bases, interdisciplinary analyses for predicting the response of the Navy's ships and related structures, this software effort is expected to provide the analyst with a convenient numerical workbench for performing large numbers of analyses that may be necessary for optimizing the design performance. Finally, an example is included that investigates several aspects of optimizing a typical naval structure from the viewpoints of strength, hydrodynamic form, and acoustic characteristics.

Description: To evaluate the role that optimization can play in structural model refinement, it is necessary to examine the existing environment for the structural design/structural modification process. The traditional approach to design, analysis, and modification is illustrated. Typically, a cyclical path is followed in evaluating and refining a structural system, with parallel paths existing between the real system and the analytical model of the system. The major failing of the existing approach is the rather weak link of communication between the cycle for the real system and the cycle for the analytical model. Only at the expense of much human effort can data sharing and comparative evaluation be enhanced for the two parallel cycles. Much of the difficulty can be traced to the lack of a user-friendly, rapidly reconfigurable engineering software environment for facilitating data and information exchange. Until this type of software environment becomes readily available to the majority of the engineering community, the role of optimization will not be able to reach its full potential and engineering productivity will continue to suffer. A key issue in current engineering design, analysis, and test is the definition and development of an integrated engineering software support capability. The data and solution flow for this type of integrated engineering analysis/refinement system is shown.

Description: The Wave Propagation Laboratory (WPL) has operated a network of radar wind Profilers in Colorado for about 1 year. The network consists of four VHF (50-MHz) radars and a UHF (915-MHz) radar. The Platteville VHF radar was developed by the Aeronomy Laboratory (AL) and has been operated jointly by WPL and AL for several years. The other radars were installed between February and May 1983. Experiences with these radars and some general aspects of tropospheric wind measurements with Doppler radar are discussed.

Description: Much of the observational evidence of large scale tropospheric-stratospheric exchange has been obtained by radiosonde and satellite radiane data. So far mesosphere-stratosphere-troposphere (MST) radars have made mininal contributions, in part due to their recent use as a meteorological tool, intermittent operation at some facilities and sparse geographic distribution. However, as more MST facilities come on-line in more locations, the good time and height resolution data throughtout the troposphere and much of the stratosphere obtainable by MST radars will enhance the detail of stratospheric and tropospheric circulations and interactions. On smaller scales MST radars have already been used to examine convective forcing from the troposphere into the stratosphere and subsequent launching of gravity waves (LARSEN et al., 1982). Observations of persistent turbulent layers in the stratosphere over Arecibo, attributable to inertial oscillations, appear to propagate away from a source region near the tropopause (SATO and WOODMAN, 1982). MST radars offer the availability of high resolution wind data in height and time needed to observe interactions between the troposphere and stratosphere. The lack of geographic coverage (e.g., equatorial regions) and insufficient data bases at many MST facilities presently inhibit studies of large-scale interactions. At present MST radars can be used to examine smaller scale interactions.

Description: The SOUSY-VHF-Radar is a pulsed coherent radar operating at 53.5 MHz and located near Bad Lauterbert, West Germany. Since 1977, the facility, operated by the Max-Planck-Institut fur Aeronomie, has been used to make a series of frontal passage observations in the spring and fall. Experiments in winter have been difficult because part of the transmitting and receiving array is usually covered by snow during that part of the year. Wavelengths around 6 m are known to be sensitive to the vertical temperature structure of the atmosphere (GREEN and GAGE, 1980; RASTOGI and ROTTGER, 1982). Thus, it has been possible to use radars operating at frequencies near 500 MHz to locate the tropopause. Comparisons between radar data and radiosonde data have shown that there is a large gradient in the radar reflectivity at the height where the radiosonde tropopause occurs. An experiment carried out by ROTTGER (1979) on March 15 to 16, 1977, showed that the radar's sensitivity to the vertical temperature structure could also be used to locate the position of fronts. The SOUSY-VHF-Radar consists of a transmitting array, also used for receiving in some configurations, that can be scanned in the off-vertical direction but not at sufficiently low elevation angles to study the horizontal extent of structures.

Description: Results obtained using the French (CNET) meteor wind radar at Ramey, Puerto Rico, and the Georgia Tech radio meteor wind facility in Atlanta, U.S.A., are presented and compared. Prevailing wind, diurnal, and semidiurnal wind amplitudes are considerably larger over Ramey than over Atlanta, but the mean zonal circulation over Atlanta is more characteristic of the equatorial circulation than winds measured by stations at higher midlatitudes. The value of continuous observations, with a height resolution of + or - 2 km, is emphasized, as is the need for the application of several techniques, groundbased, in situ and satellite, if projects such as the MAP GLOBMET are to succeed in delineating the global meteorology of the mesopause.

Description: A superposed epoch analysis during late winter zonal wind reversals was carried out from 18 year observation series (1963 to 1980) of the meridional geopotential height gradient in the 30 mb level (latitude mean) and of the ozone content over central Europe. Experimental data suggest that if planetary waves are responsible for the additional meridional ozone transport during stratospheric warmings, this transport has to take place at heights other than those up to the ozone maximum in the middle latitudes.

Description: The middle atmosphere circulation is governed by two seasonal basic states in winter and summer, twice a year separated by relatively shortlived reversal periods. These seasonal basic states of circulation and the spring changeover period between them are investigated.

Description: Recently it has become clear that the phenomena in the ionospheric D-region are determined to a great extent by dynamical processes in the strato-mesosphere D-region. In this respect much attention is paid to the study of the winter anomaly (WA) phenomenon on medium and short radiowaves, in which the meteorological character of the lower ionosphere is most prominent. Significant experimental data about the variations of the electron concentration, N, ion composition, temperature and dynamic regime during WA permit a better understanding of the character of the physical processes in the middle atmosphere. The influence of the neutral wind on the seasonal variation of the electron concentration N for the altitude interval 90 or = z or = 120 km, where the ratio upsilon sub in/omega sub i, of the ion-neutral collision frequency, upsilon sub in and the ion gyrofrequency, omega sub i decreases from 40 to 1 was evaluated. CIRA-72 is used as a model of the zonal wind.

Description: Several case studies are examined in an attempt to relate Visible infrared spin scan radiometers Atmospheric Sounder (VAS) water vapor channel radiance data to atmospheric moisture. Since the 6.7 micrometer channel detects radiation emitted by atmospheric water vapor from a rather thick layer, a scheme is developed which weighted rawinsonde observations of relative humidity in a similar manner. A comparison of the two fields (weighted relative humidity values from gridded rawinsonde observations and the VAS water vapor image) indicates that even when mesoscale data are used, the technique only presented a smooth representation of the radiance field. This weighting function is dependent on both the temperature and moisture distribution of the atmosphere. Cross sections of relative humidity from the mesoscale rawinsondes are produced which sliced the water vapor imagery in particularly interesting regions (areas of high and low blackbody temperatures). Comparisons are then made between the cross sections and the variations in the VAS radiance data along the cross section line. Bright regions in the water vapor imagery (cold blackbody temperatures) are often associated with thin layers of high relative humidity or thick layers of only moderately moist air. The reverse also applies, i.e., dark regions (warm blackbody temperatures) in the imagery corresponded well with very dry regions in the cross sections.

Description: Progress on the Mesoscale and Severe Storms (MASS) data management and analysis system is described. An interactive atmospheric data base management software package to convert four types of data (Sounding, Single Level, Grid, Image) into standard random access formats is implemented and integrated with the MASS AVE80 Series general purpose plotting and graphics display data analysis software package. An interactive analysis and display graphics software package (AVE80) to analyze large volumes of conventional and satellite derived meteorological data is enhanced to provide imaging/color graphics display utilizing color video hardware integrated into the MASS computer system. Local and remote smart-terminal capability is provided by installing APPLE III computer systems within individual scientist offices and integrated with the MASS system, thus providing color video display, graphics, and characters display of the four data types.

Description: New analysis methods were developed and refined for the synthesis of wind fields from multiple Doppler radar data. Considerable software was written and debugged for wind field synthesis. The analysis methods were applied to radar data collected during the CCOPE experiment in which lidar wind measurements were also made. The analysis method differs from existing methods in that interpolation (using filters with assigned weights) and advection of data, to account for time differential between data acquisition at different points, are not used. Instead, functional fits were used in space and time coordinates to transfer radial velocity data to a space-time grid. Subsequently the wind synthesis is performed. This method gives better space resolution in the synthesized winds, compared to other methods in common use, by better preserving the gradients of velocities. The wind fields show the cellular structure characteristic of boundary-layer convection. Also evident in the analysis are the sharp transitions and gradients in the wind field which were preserved by the synthesis.

Description: Intercomparison of wind data from the airborne Doppler lidar, ground-based Doppler radars, the 444 m NSSL-KTVY tower, and rawinsonde were completed. The vertical profile of wind in the PBL measured by the radars compared favorably with the profiles measured by the tower and rawinsonde while the one obtained from lidar data differed from the other three by as much as 3m/sec in wind speed and 38 degrees in direction. The time dependence of differences in wind estimates from radar and lidar suggested that these discrepencies could be attributed to a Schuler resonance in the aircraft's inertial navigation system which caused an erroneous component of the aircraft's velocity vector to be subtracted from the lidar radial velocities, thus creating errors in the synthesized wind speed and direction. The vertical profile of turbulent fluctuations of the horizontal wind detected by the different systems compared well. Also, spectra from the different sensing systems compared well in both magnitude and shape, suggesting that the lidar and radar detected similar turbulent structure.

Description: The verification of the Doppler lidar wind measurement is continued. The in situ measurements on a 500 meter tall tower are used to check the lidar determined winds (flight 4), followed by other tests applied to the extensive data sets of flights 19 and 21. After checking for possible software errors in the processing programs, the inconsistency was not solved. The source of the errors appears to be the uncertainty in the calculation of the contribution of the aircraft motion to the lidar measured line of sight speed. Possible techniques for estimating the aircraft motion errors from the aircraft data are investigated.

Description: A lightning detection system which has been operating along the East Coast since August 1982 is outlined. The system will prove to be one source of ground truth for lightning flashes detected from above clouds. The first absolute spectral irradiance measurements over a wide wavelength range were reported. The observations of lightning from a U2 aircraft are reviewed.

Description: A series of cosmic ray neutron monitor data which were used in three analyses: (1) solar activity influence on ionization of the upper troposphere and tropopause; (2) solar activity influence on Canadian high stratus in winter; and (3) the S3-4 satellite study of IMF/GMF magnetic coupling effects are reported. The magnetic coupling model of solar activity influence on atmospheric processes were investigated. The magnetic coupling model is used to explain a number of seemingly diverse studies lightning incidence is emphasized.

Description: Measurement of lightning location data which occur together with continental thunderstorms and hurricanes was examined, and a second phase linear interferometer was deployed. Electrical emission originating from tropical storms in the Gulf of Mexico were monitored. The time span between hurricane ALLEN (10 August 1980) and hurricane ALICIA (18 August 1983) represents the longest period that the United States has gone without hurricane landfall. Both systems were active and data were acquired during the landfall period of hurricane ALICIA.

Description: Optical signals radiated by Florida lightning were recorded in correlation with wideband electric field signatures. The amplitudes and time behavior of the early portion of the signals produced by return strokes indicate that this lightning process produces a space and time averaged peak radiance.

Description: Analyses of single station measurements of the Maxwell current density (Jm) made under Florida thunderstorms during the summer of 1981 have been completed. The results of these analyses indicate that: (1) Jm is usually dominated by the displacement current component when the electric field is close to zero; (2) Jm is steady with time in the intervals between lightning flashes; (3) Jm is not altered significantly by lightning; and (4) the average value of Jm changes slowly and over time scales that are comparable to those required for storm development. Maps have also been derived of the surface Maxwell current density for a number of the Florida TRIP (76-78) storms using field mill data to estimate Jm from the displacement current density. Studies show that these maps provide a good indication of the location and relative intensity of the storm current generators, and area-integrations of the current contours provide estimates of the total storm currents.

Description: Successful ground truth support of U-2 overflights was been accomplished. Data have been reduced for 4 June 1984 and some of the results have been integrated into some of MSFC's efforts. Staccato lightning (multiply branched, single stroke flash with no continuing current) is prevalent within the rainfree region around the main storm updraft and this is believed to be important, i.e., staccato flashes might be an important indicator of severe storm electrification. Results from data analysis from two stations appear to indicate that charge center heights can be estimated from a combination of intercept data with data from the fixed laboratory at NSSL. An excellent data base has been provided for determining the sight errors and efficiency of NSSL's LLP system. Cloud structures, observable in a low radar reflectivity region and on a scale smaller than is currently resolved by radar, which appear to be related to electrical activity are studied.

Description: The problem of the effects of the latent heat release on the waves with both upper and lower boundary frictional effects is investigated. The influence of the vertical shear of the basic wind in these models will be investigated. These investigations will shed some light on the method of solution to the problem of including the effect of Ekman pumping on the moist baroclinic waves in the model of Tang and Fichtl.

Description: Dynamical processes involved in comma cloud formation, and passive tracer evolution in a baroclinic wave are discussed. An analytical solution was obtained demonstrating the complex nongeostrophic flow pattern involved in the redistribution of low level constituents in a finite amplitude baroclinic wave, and in the formation of the typical humidity and cloud distributions in such a wave. Observational and theoretical studies of blocking weather patterns in middle latitude flows were studied. The differences in the energy and enstrophy cascades in blocking and nonblocking situations were shown. It was established that pronounced upscale flow of both of these quantities, from intermediate to planetary scales, occurs during blocking episodes. The upscale flux of enstrophy, in particular, suggests that the persistence of blocking periods may be due to reduced dissipation of the large scale circulation and therefore entail some above normal predictability.

Description: Generalized energetics were studied for nonlinear inviscid symmetric instability (SI). It was found that the linear theory fails to predict the stability in certain cases where the basic state is transitional between stability and instability. The initial growth of the SI perturbations can be fairly well approximated by linear theory, but the long time nonlinear evaluations will be bonded energetically if the SI region is finite. However, a further extension of the energetics to conditional symmetric instability (CSI) shows that the nonlinear evolution of circulation will energetically depend much more on the precipitation in a complicated way. By treating the latent heat as a source which is implicitly related to the motion field, the existence, uniqueness and stability of steady viscous (CSI) circulations are studied. Viscous CSI circulations are proved to be unique and asymptotically stable when the heat sources are weak and less sensitive to the motion perturbations. By considering the fact that moist updrafts are narrow and using eddy viscosity of 0(1,000 m squared/s) the stability criterion suggests that some frontal rainbands were probably dominated by the CSI mechanism even in their mature quasi-steady stage.

Description: The basic analysis equations, i.e., the two horizontal momentum equations, the hydrostatic equation, and the integrated continuity equation were derived for the nonlinear vertical coordinate, nondimensionalized, and expressed in finite differences on a staggered grid. Special care was taken to transform the hydrostatic equation and the pressure gradient terms of the horizontal momentum equations to nearly eliminate truncation error over steeply sloping terrain. This formulation also eliminated explicit reference to orographically induced variations in the thermodynamic variables so that the variational adjustments are on the scale of the meteorological perturbations. The analysis equations were subjected to the Euler-Lagrange operations as expressed for finite differences and an additional set of five partial differential equations was derived, bringing to nine the number of equations in Model I. Higher order terms, terms containing observed quantities, and terms containing none of the variables to be adjusted were grouped into forcing functions and the equations were solved for the zero order terms. Zero order variables were eliminated between these equations and there resulted two diagnostic equations which take the form of general linear second order partial differential equations with nonconstant coefficients.

Description: Atmospheric effects on lidar systems at 10.6 micron wavelength involving molecular absorption, aerosol scattering and refractive turbulence effects are discussed. Work on the combined effects of beam truncation and atmospheric refractive turbulence on the system performance are discussed, as well as the modeling of backscattering characteristics of atmospheric aerosols.

Description: Efforts in support of a global backscatter mission are reviewed briefly. Lidar system sensitivity was calibrated by means of ground-based tests. The analysis of ground-based data and planning of a global backscatter mission were conducted. Proposals for FY-85 include using a more powerful laser to conduct backscatter measurements.

Description: Vibration, out-gas, and acoustic tests performed on the Geophysical Fluid Flow Cell (GFFC) instrument are reported. The slope of the 59 experiments to be performed by GFFC is outlined. Spacelab 3 crew training on the operation of the GFFC instrument is mentioned.

Description: Computer programming was completed for digital acquisition of temperature and velocity data generated by the Geophysical Fluid Flow Cell (GFFC) during the upcoming Spacelab 3 mission. A set of scenarios was developed which covers basic electro-hydrodynamic instability, highly supercritical convection with isothermal boundaries, convection with imposed thermal forcing, and some stably stratified runs to look at large-scale thermohaline ocean circulations. The extent to which the GFFC experimental results apply to more complicated circumstances within the Sun or giant planets was assessed.

Description: The mathematical statement of the general nonlinear optimization problem is given as follows: find the vector of design variables, X, that will minimize f(X) subject to G sub J (x) + or - 0 j=1,m H sub K hk(X) = 0 k=1,l X Lower I approx less than X sub I approx. less than X U over I i = 1,N. The vector of design variables, X, includes all those variables which may be changed by the ADS program in order to arrive at the optimum design. The objective function F(X) to be minimized may be weight, cost or some other performance measure. If the objective is to be maximized, this is accomplished by minimizing -F(X). The inequality constraints include limits on stress, deformation, aeroelastic response or controllability, as examples, and may be nonlinear implicit functions of the design variables, X. The equality constraints h sub k(X) represent conditions that must be satisfied precisely for the design to be acceptable. Equality constraints are not fully operational in version 1.0 of the ADS program, although they are available in the Augmented Lagrange Multiplier method. The side constraints given by the last equation are used to directly limit the region of search for the optimum. The ADS program will never consider a design which is not within these limits.

Description: The purpose of this project was to investigate the use of optimization techniques to improve the flutter margins of the HARM AGM-88A wing. The missile has four cruciform wings, located near mid-fuselage, that are actuated in pairs symmetrically and antisymmetrically to provide pitch, yaw, and roll control. The wings have a solid stainless steel forward section and a stainless steel crushed-honeycomb aft section. The wing restraint stiffness is dependent upon wing pitch amplitude and varies from a low value near neutral pitch attitude to a much higher value at off-neutral pitch attitudes, where aerodynamic loads lock out any free play in the control system. The most critical condition for flutter is the low-stiffness condition in which the wings are moved symmetrically. Although a tendency toward limit-cycle flutter is controlled in the current design by controller logic, wing redesign to improve this situation is attractive because it can be accomplished as a retrofit. In view of the exploratory nature of the study, it was decided to apply the optimization to a wing-only model, validated by comparison with results obtained by Texas Instruments (TI). Any wing designs that looked promising were to be evaluated at TI with more complicated models, including body modes. The optimization work was performed by McIntosh Structural Dynamics, Inc. (MSD) under a contract from TI.

Description: The work that has been done in the last decade or so in the application of optimization techniques to vehicle design is discussed. Much of the work reviewed deals with the design of body or suspension (chassis) components for reduced weight. Also reviewed are studies dealing with system optimization problems for improved functional performance, such as ride or handling. In reviewing the work on the use of optimization techniques, one notes the transition from the rare mention of the methods in the 70's to an increased effort in the early 80's. Efficient and convenient optimization and analysis tools still need to be developed so that they can be regularly applied in the early design stage of the vehicle development cycle to be most effective. Based on the reported applications, an attempt is made to assess the potential for automotive application of optimization techniques. The major issue involved remains the creation of quantifiable means of analysis to be used in vehicle design. The conventional process of vehicle design still contains much experience-based input because it has not yet proven possible to quantify all important constraints. This restraint on the part of the analysis will continue to be a major limiting factor in application of optimization to vehicle design.

Description: In optimizing a helicopter configuration, Hughes Helicopters uses a program called Computer Aided Sizing of Helicopters (CASH), written and updated over the past ten years, and used as an important part of the preliminary design process of the AH-64. First, measures of effectiveness must be supplied to define the mission characteristics of the helicopter to be designed. Then CASH allows the designer to rapidly and automatically develop the basic size of the helicopter (or other rotorcraft) for the given mission. This enables the designer and management to assess the various tradeoffs and to quickly determine the optimum configuration.

Description: Optimum Preliminary Design of Transports (OPDOT) is a computer program developed at NASA Langley Research Center for evaluating the impact of new technologies upon transport aircraft. For example, it provides the capability to look at configurations which have been resized to take advantage of active controls and provide and indication of economic sensitivity to its use. Although this tool returns a conceptual design configuration as its output, it does not have the accuracy, in absolute terms, to yield satisfactory point designs for immediate use by aircraft manufacturers. However, the relative accuracy of comparing OPDOT-generated configurations while varying technological assumptions has been demonstrated to be highly reliable. Hence, OPDOT is a useful tool for ascertaining the synergistic benefits of active controls, composite structures, improved engine efficiencies and other advanced technological developments. The approach used by OPDOT is a direct numerical optimization of an economic performance index. A set of independent design variables is iterated, given a set of design constants and data. The design variables include wing geometry, tail geometry, fuselage size, and engine size. This iteration continues until the optimum performance index is found which satisfies all the constraint functions. The analyst interacts with OPDOT by varying the input parameters to either the constraint functions or the design constants. Note that the optimization of aircraft geometry parameters is equivalent to finding the ideal aircraft size, but with more degrees of freedom than classical design procedures will allow.