ALBERT

Description: Microgravity offers a unique environment for studying polymer diffusion and polymer polymerization reactions. The absence of convection currents, which are the major mode of mixing at the molecular level on Earth, are eliminated or reduced in the microgravity environment. More importantly, the prediction of unique copolymer composition development in microgravity allows controlled formation of new compositions of matter. The absence of mixing at the molecular level should produce unique short block copolymers available for the first time for comonomer compositions which normally lead to random or long block copolymer under good mixing. The investigation of fundamental polymer diffusion and polymer polymerization processes in microgravity is proposed. This effort will involve fundamental studies of monomer and polymer diffusion; their effects on initiation, propagation, and especially termination kinetics rate constant; and the accurate evaluation of copolymerization reactivity ratios in microgravity. The experimental design is presented for these studies along with an evaluation technique for in situ monitoring of polymer diffusion and polymerization kinetics.

Description: The analysis of light scattered from an ensemble of particles has long been a preferred method for characterizing their physical properties. Instrumentation to perform the measurements which forms the basis for such analysis is available in many forms based upon a variety of different experimental techniques. A system is presented which is singularly applicable for making many types of measurements in a microgravity environment. The commercial version of this device, the DAWN-F, has been used in many labs throughout the world to perform analyses of particular importance for both research and production. Light scattering theory is reviewed and the structure and function of the system is described.

Description: Avalanche photodiodes (APD) are excellent small area, solid state detectors for photon counting. Performance possibilities include: photon detection efficiency in excess of 50 percent; wavelength response from 400 to 1000 nm; count rate to 10 (exp 7) counts per sec; afterpulsing at negligible levels; timing resolution better than 1 ns. Unfortunately, these performance levels are not simultaneously available in a single detector amplifier configuration. By considering theoretical performance predictions and previous and new measurements of APD performance, the anticipated performance of a range of proposed APD-based photon counting modules is derived.

Description: Traditional optical systems for photon correlation spectroscopy and laser anemometry have relied upon physically large and fairly expensive lasers, bulk-optics such as lenses of a few inches diameter, large mechanical mounts and carefully selected, fragile and bulky photon counting photomultiplier detectors. In some cases, experimental fluid dynamics at a desired position in a flow, perhaps deep inside complex machinery, is physically impossible or very difficult. Similar problems exist with photon correlation spectroscopy, e.g., remote and heterodyne experiments. Various optical and electro optical components were investigated and characterized with the aim of replacing existing photon correlation laser spectroscopy and anemometry techniques in miniaturized form, and with significant cost reduction. Very recently, a range of miniature, modular light scattering systems were constructed from little solid state optical and electro optical components, and experimentally verified measurement performance comparable to standard lab photon correlation spectroscopy and laser anemometry equipment.

Description: The design goals and results of an advanced development stronglink are discussed. Special emphasis is placed on a new rotary solenoid concept to provide improved security during the handling, storage, transporting, and deployment of weapons to prevent accidental detonation of the weapons in the event of abnormal environments, such as impact, fire, crush, etc.

Description: Images from an airborne, scanning radiometer operating at a frequency of 98 GHz have been analyzed. The millimeter-wave images were obtained in 1985-1986 using the JPL millimeter-wave imaging sensor. The goal of this study was to enhance the information content of these images and make their interpretation easier. A visual-interpretative approach was used for information extraction from the images. This included application of nonlinear transform techniques for noise reduction and for color, contrast, and edge enhancement. Results of using the techniques on selected millimeter-wave images are discussed.

Description: In June 1978, the Seasat satellite was launched carrying, among other instruments, the Seasat-A scatterometer system (SASS), which produced ambiguous wind speed and direction data at the ocean surface. A fifteen day subset of dealiased wind vector data with the inherent ambiguities removed was produced for the period of September 6-20, 1978. On September 8, SASS began to observe a development of frontal cyclogenesis in the South Pacific off the east coast of New Zealand, in an area of few surface observations. A large mature cyclone contained weak warm and cold fronts and an occlusion with a strong horizontal wind shear. Satellite imagery shows that a strong upper-level jet streak was moving rapidly over the area of the surface frontal occlusion and as the jet passed over this area a new vortex formed. This cyclogenesis event was studied using 50-km resolution scatterometer surface wind data. High-resolution fields of wind vectors, divergence and vorticity are computed and plotted from the scatterometer data to study the structure and development of the newly formed cyclonic vortex, not otherwise possible using conventional observations.

Description: The NASA scatterometer (NSCAT) is a spaceborne scatterometer scheduled to be deployed in the mid-1990s. An analysis of the wind retrieval error distribution for wind estimates based on backscatter measurements made by the NSCAT instrument is presented. The results are based on an end-to-end simulation of the scatterometer instrument and data processing. In general, the distribution of the wind speed error, when normalized, is independent of the true wind speed and direction. The wind speed error can be characterized by a normal distribution. The wind direction error is independent of the true wind speed, but depends on the true wind direction. Details for wind vectors with true wind speeds from 3 m/s to 33 m/s and true wind directions from 0 to 360 deg are presented.

Description: Interdigitated photoconductive detectors with 5-micron geometry have been fabricated on HEMT material and their optical response characteristics at 820 nm have been examined at dc and in the frequency range of 2-8 GHz. These have been compared with characteristics of similar 1-micron devices on MESFET material. The shapes of the frequency responses were found to differ, but the useful bandwidth of both types of devices was found to be similar.

Description: Modulation of a rain wave pattern by longer waves has been studied. An analytical model taking into account capillarity effects and obliquity of short waves has been developed. Modulation rates in wave number and amplitude have been computed. Experiments were carried out in a wave tank. First results agree with theoretical models, but higher values of modulation rates are measured. These results could be taken into account for understanding the radar response from the sea surface during rain.

Description: Rainfall modification of directional scatterometer response from the sea surface was simulated in wind-wave tank experiments. Data show that for the range of conditions in laboratory experiments, rain enhances radar cross section for all azimuthal angles relative to wind direction. This result broadens previous measurements, which showed that scatterometer response increases with increasing rainfall for radars pointing upwind. But more to the point, the data also show that the directional dynamic-range of scatterometry diminishes rapidly as rainfall rate increases. Thus, while it may be possible to determine wind speed and direction during rain, it will require adequate system sensitivity.

Description: An account of the construction of surface pressure fields from Seasat-A satellite scatterometer (SASS) winds as carried out by different methods, and the comparison of these pressure fields with those derived from in situ ship observations is presented. On the assumption that the pressure adjusts itself instantaneously to the motion field, it may be computed by various methods. One of these makes use of planetary boundary theory, and of the possible techniques in this category a two-layer iterative scheme admitting of the parametrization of diabatic and baroclinic effects and of secondary flow was chosen. A second method involves the assumption of zero two-dimensional divergence, leading to a Laplace's equation (the balance equation) in pressure, with the wind field serving as a forcing function. This method does not accommodate adiabatic or baroclinic effects, and requires a knowledge of the pressure at all boundary points. Two comparison fields are used for validation: the conventional operational analyses of the US National Meteorological Center (NMC), and the special analyses of the Gulf of Alaska Experiment (GOASEX), which were done by hand. The results of the computations were as follows: (1) The pressure fields, as computed from the SASS winds alone, closely approximated the NMC fields in regions where reasonable in situ coverage was available (typically, one or two mb differences over most of the chart, three to four mb in extreme cases); (2) In some cases the SASS-derived pressure fields displayed high-resolution phenomena not detected by the NMC fields, but evident in the GOASEX data; and, (3) As expected, the pressure fields derived from the balance equation were much smoother and less well resolved than the SASS-derived or NMC fields. The divergence as measured from the SASS winds is smaller than, but of the same order of magnitude as, the vorticity.

Description: The accuracy of temperature, pressure, potential temperature, and horizontal wind measurements is discussed in connection with the use of Meteorological Measurement System data in the AAOE. The vertical distribution of temperature measurements and latitudinal variations of the zonal wind for 12 flights over Antarctica during the 1987 AAOE campaign are summarized. Model atmospheres from 0 to 32 km at 70 deg and 55 deg S for the August-September period are constructed. Above the 420 K isentropic surface, the polar vortex remains strong throughout August and September of 1987.

Description: The formulation and evolution of polar stratospheric ice clouds are simulated using a one-dimensional model of cloud microphysics. It is found that the optical thickness and particle size of ice clouds depend on the cooling rate of the air in which the cloud formed. It is necessary that there be an energy barrier to ice nucleation upon the preexisting aerosols in order to account for the cooling rate dependence of the cloud properties.

Description: The history of minimum temperatures at 50 and 70 mb is examined from NMC, UK Met O and ECMWF analyses. MSU channel 24 data are similarly inspected. South Pole sonde data are used to calculate saturation humidity mixing ratio as a function of altitude and time throughout 1987. Saturation with respect to ice could be maintained for water mixing ratios of 3.5 ppmv for a period of about 80 days from mid-June to mid-September. Dehydration to mixing ratios of 1 ppmv or less was possible sporadically. Data from the ER-2 flights between 53 S and 72 S are used in conjunction with particle size measurements and air parcel trajectories to demonstrate the dehydration occurring over Antarctica. Water mixing ratios at the latitude of Punta Arens (53 S), in conjunction with tracer measurements and trajectory analysis, show that at potential temperatures from about 325 to 400 K, the dryness (less than 3 ppmv) had its origin over Antarctica rather than in the tropics. Water mixing ratios within the Antarctic vortex varied from 1.5 to 3.8 ppmv, with a strong isentropic gradient being evident in the region of high potential vorticity gradients.

Description: Measurements of total reactive nitrogen, NOy, total water vapor, and aerosols were made as part of the Airborne Antarctic Ozone Experiment. The measurements were made using instruments located onboard the NASA ER-2 aircrafts which conducted twelve flights over the Antarctic continent reaching altitudes of 18 km at 72 S latitude. Each instrument utilized an ambient air sample and provided a measurement up to 1 Hz or every 200 m of flight path. The data presented focus on the flights of Aug. 17th and 18th during which Polar Stratospheric Clouds (PSCs) were encountered containing concentrations of 0.5 to 1.0 micron diameter aerosols greater than 1 cm/cu. The temperature pressure during these events ranged as low as 184 K near 75 mb pressure, with water values near 3.5 ppm by volume (ppmv). With the exception of two short periods, the PSC activity was observed at temperatures above the frost point of water over ice. The data gathered during these flights are analyzed and presented.

Description: A multichannel statistical approach is used to retrieve rainfall rates from the brightness temperature T(B) observed by passive microwave radiometers flown on a high-altitude NASA aircraft. T(B) statistics are based upon data generated by a cloud radiative model. This model simulates variabilities in the underlying geophysical parameters of interest, and computes their associated T(B) in each of the available channels. By further imposing the requirement that the observed T(B) agree with the T(B) values corresponding to the retrieved parameters through the cloud radiative transfer model, the results can be made to agree quite well with coincident radar-derived rainfall rates. Some information regarding the cloud vertical structure is also obtained by such an added requirement. The applicability of this technique to satellite retrievals is also investigated. Data which might be observed by satellite-borne radiometers, including the effects of nonuniformly filled footprints, are simulated by the cloud radiative model for this purpose.

Description: This paper presents the results of a field program using a ground-based Raman lidar system to observe changes in moisture profiles as a cold and a warm front passed over the NASA/Goddard Space Flight Center in Greenbelt, Maryland. The lidar operating only during darkness is capable of providing continuous high vertical resolution profiles of water vapor mixing ratio and aerosol scattering ratio from near the surface to about 7 km altitude. The lidar data acquired on three consecutive nights from shortly after sunset to shortly before sunrise, along with upper air data from specially launched rawinsondes, have provided a unique visualization of the detailed structure of the two fronts.

Description: Several silicon solar cells having thicknesses of approximately 63 microns, with and without back-surface fields (BSF), were irradiated with 1-MeV protons having fluences between 10 to the 10th and 10 to the 12th sq cm. The irradiations were performed using both normal and isotropic incidence on the rear surfaces of the cells. It was observed that after irradiation with fluences greater than 10 to the 11th protons/sq cm, all BSF cells degraded at a faster rate than cells without BSF. The irradiation results are analyzed using a model in which irradiation-induced defects in the BSF region are taken into account. Tentatively, it is concluded that an increase in defect density due to the formation of aluminum and proton complexes in BSF cells is responsible for the higher-power loss in the BSF cells compared to the non-BSF cells.

Description: A simple circuit was designed to measure the phase difference between two noisy sine waves. It locks over a wide range of frequencies and produces an output proportional to the phase difference of rapidly varying signals. A square wave locked in frequency and phase to the first signal is produced by a phase-locked loop and is amplified by an operational amplifier.

Description: A solid-state, resistance tailorable, programmable-once, binary, nonvolatile memory switch based on manganese oxide thin films is reported. MnO(x) exhibits irreversible memory switching from conducting (on) to insulating (off) state, with the off and on resistance ratio of greater than 10,000. The switching mechanism is current-triggered chemical transformation of a conductive MnO(2-Delta) to an insulating Mn2O3 state. The energy required for switching is of the order of 4-20 nJ/sq micron. The low switching energy, stability of the on and off states, and tailorability of the on state resistance make these microswitches well suited as programmable binary synapses in electronic associative memories based on neural network models.

Description: It is shown how a commercial time interval counter can be used to measure the relative stability of two signals that are offset in frequency and mixed down to a beat note of about 1 Hz. To avoid the dead-time problem, the counter is set up to read the time interval between each beat note upcrossing and the next pulse of a 10 Hz reference pulse train. The actual upcrossing times are recovered by a simple algorithm whose outputs can be used for computing residuals and Allan variance. A noise floor-test yielded a delta f-f Allan deviation of 1.3 times 10 to the minus 9th power/tau relative to the beat frequency.

Description: An improved version of the GISS Model II cumulus parameterization designed for long-term climate integrations is used to study the effects of entrainment and multiple cloud types on the January climate simulation. Instead of prescribing convective mass as a fixed fraction of the cloud base grid-box mass, it is calculated based on the closure assumption that the cumulus convection restores the atmosphere to a neutral moist convective state at cloud base. This change alone significantly improves the distribution of precipitation, convective mass exchanges, and frequencies in the January climate. The vertical structure of the tropical atmosphere exhibits quasi-equilibrium behavior when this closure is used, even though there is no explicit constraint applied above cloud base.

Description: The joint frequency distribution technique was used to analyze buoyancy fluxes in the marine atmospheric boundary layer (MABL) for the cloud street regime noted during the Genesis of Atlantic Lows Experiment. It is found that for the lower half of the MABL, the buoyancy flux is mainly generated by the rising thermals and the sinking compensating ambient air, and is mainly consumed by the entrainment and detrainment of thermals, penetrative convection, and the entrainment from the MABL top. If the buoyancy flux is primarily driven by the temperature flux, these buoyancy-flux generating processes should be the same for the lower boundary layers over land and ocean. The results of the scale analysis of the buoyancy flux agree well with those obtained for mesoscale cellular convection during the Air-Mass Transformation Experiment.

Description: Results are presented on numerical experiments that were carried out to investigate the mechanisms of the observed variabilities in wind and convection associated with supercloud clusters (SCCs), westerly wind bursts, and 30-60 day oscillations in the western Pacific region. It is shown that the generation of a 30-60 day eastward propagating precipitation pattern in the Lau and Peng (1987) model, which can be identified as SCC, is accompanied by convective clusters coming in opposite direction to that of the SCC itself. The results suggest that the westward propagating cloud clusters are produced at the initial stage of the 30-60 day disturbance due to mutual adjustment of the large-scale flow and heating.

Description: A correction factor to the number density measured by the Forward Scattering Spectrometer Probe (FSSP) which compensates for dead time and coincidence errors was determined by calculating the probabilities of, and the average number of particles in, the six possible types of dead time and coincidence events. These probabilities and averages were calculated by means of a probabilistic model based on Poisson statistics. A Monte Carlo computer simulation of the FSSP operation was also carried out and the number density correction factor was compared with the Monte Carlo data. For an actual number density of 2000/cu cm, it was found that the measured number density was of the order of 300/cu cm.

Description: Measurement of times of flight of sound waves can be used to determine temperatures in a gas. This paper describes a system, based on this principle, that is capable of giving the temperature profile in a nonisothermal gas volume, for example, prevalent in a large furnace. The apparatus is simple, rugged, accurate, and capable of being automated for process control applications. It is basically an acoustic waveguide where the outside temperature profile is transferred to a chosen gas contained inside the guide.

Description: The development of a unique noncontact temperature measurement device utilizing rotating analyzer ellipsometry is described. The technique circumvents the necessity of spectral emissivity estimation by direct measurement concomitant with radiance brightness. Simultaneous determinations of dielectric constants and refractive indices allow changes in the physical and chemical state of a heated surface to be monitored. The results of optical property measurements at 633 nm as functions of temperature between 1000 and 2500 K for eight transition metals including Hf, Ir, Mo, Nb, Pd, Pt, Ta, and V are presented together with preliminary results of oxidation studies on iridium.

Description: A novel technique is presented which should allow precise determination of the temperature dependence of the inductance, and hence of the penetration depth, of superconducting niobium thin-film structures. Four niobium thin-film stripline inductors are arranged in a bridge configuration, and inductance differences are measured using a potentiometric technique with a SQUID (superconducting quantum interference device) as the null detector. Numerical simulations of the stripline inductances are presented which allow the performance of the measurement technique to be evaluated. The prediction of the two-fluid model for the penetration-depth temperature dependence is given for reduced temperatures of 0.3 to 0.9. The experimental apparatus and its resolution and accuracy are discussed.

Description: An optically controlled reflection modulator has been demonstrated that consists of a combination of a GaAs-AlGaAs n-i-p-i doping structure with a multiple-quantum-well structures on top of a distributed Bragg reflector, all grown by MBE. A modulation of approximately 60 percent is obtained on the test structure, corresponding to a differential change of absorption coefficient in the quantum wells of approximately 7500/cm. Changes in reflectance can be observed with a control beam power as low as 1.5 microW. This device structure has the potential of being developed as an optically addressed spatial light modulator for optical information processing.

Description: The effect of SiO2 encapsulation on reaction rates in the Au-InP system was studied. Scanning electron microscopy and x-ray photoelectron spectroscopy were used to investigate surface and/or interface morphologies and in-depth compositional profiles. It was found that the rate of dissolution of InP into Au and subsequent phase transformations are largely dependent on the condition of the free surface of the metalization. SiO2 capping of Au is reported for the first time to suppress the Au-InP reaction rate. The Au-InP interaction is shown to be quite similar to the Au-GaAs interaction despite differences in behavior of the group-V elements.

Description: A design concept developed for a polarimeter on the vector magnetograph of the SAMEX satellite that would be very sensitive to solar vector magnetic fields is described. A description of the Poincare sphere is presented, along with the instrument scientific requirements, to provide an understanding of how the polarimeter design has been selected. It is shown that the design goal of a polarimetric sensitivity of 0.0001 can be achieved in the linear measurements using a hybrid analyzer. It is also noted that the systematic errors that produce linear crosstalk into the circular measurement will require the use of the redundant polarization measurements for in-flight calibrations and corrections of the data.

Description: The present analysis method for hot-wire data in supersonic turbulence takes sound field effects into account and yields greater accuracy in its treatment of flow variable fluctuations than existing methods despite requiring only a moderately accurate estimate of static pressure fluctuations. The method demonstrates the way in which neglecting pressure fluctuations will affect hot-wire data analysis, as well as indicating the probable direction the errors will take.

Description: Displays of multifrequency passive microwave data from the Special Sensor Microwave/Imager (SSM/I) flying on the Defense Meteorological Satellite Program (DMSP) spacecraft are presented. Observed brightness temperatures at 85.5 GHz (vertical and horizontal polarizations) and 37 GHz (vertical polarization) are respectively used to 'drive' the red, green, and blue 'guns' of a color monitor. The resultant false-color images can be used to distinguish land from water, highlight precipitation processes and structure over both land and water, and detail variations in other surfaces such as deserts, snow cover, and sea ice. The observations at 85.5 GHz also add a previously unavailable frequency to the problem of rainfall estimation from space. Examples of mesoscale squall lines, tropical and extra-tropical storms, and larger-scale land and atmospheric features as 'viewed' by the SSM/I are shown.

Description: A postdispersion system for astronomical observations with Fourier transform spectrometers in the thermal infrared has been developed which improves the sensitivity of radiation noise limited observations by reducing the spectral range incident on the detector. Special attention is given to the first-generation blocked impurity band detector. Planetary, solar, and stellar observations are reported.

Description: The design of a VLSI chip which applies the ideas of distributed arithmetic to a nonrecursive digital filter is described. The main features of this design are very high precision and a high degree of flexibility, which allows one chip to implement a large number of quite different digital filters and correlators.

Description: The measurement by a three-dimensional laser Doppler velocimeter of a turbulent flow has been numerically simulated. Errors associated with the probe volume geometry and the coincidence time window concept are revealed. One type of error occurs for high system data rates when multiple particles lead to system realizations. Another error occurs associated with a geometric bias discovered in the present study. This three-dimensional ldv geometric bias exists even for single-particle realizations and regardless of the system data rate. A technique for the elimination of the geometric bias is presented.

Description: A computer-controlled tunable diode laser spectrometer and spectral analysis software are described. The three-channel system records simultaneously the transmission of a subject gas, a temperature-stabilized etalon, and a calibration gas. The software routines are applied to diode laser spectra of HNO3 and NO2 to illustrate the procedures adopted for conversion of raw spectral data to useful transmission and harmonic spectra. Extraction of line positions, absorption intensities, collisional broadening coefficients, and gas concentrations from recorded spectra is also described.

Description: Optical interconnects are being considered for control signal distribution in phased array antennas. A packaged hybrid GaAs optical controller with a 1:16 demultiplexed output that is suitable for this application is described. The controller, which was fabricated using enhancement/depletion mode MESFET technology, operates at demultiplexer-limited input data rates up to 305 Mb/s and requires less than 200 microW optical input power.

Description: A technique has been developed to support the study of the effects of cosmic rays on integrated circuits. The system is designed to determine the particle distribution across the surface of an integrated circuit accurately while the circuit is bombarded by a particle beam. The system uses photomultiplier tubes, an octal discriminator, a computer-controlled NIM quad counter, and an IBM PC. It provides real-time operator feedback for fast beam tuning and monitors momentary fluctuations in the particle beam. The hardware, software, and system performance are described.

Description: A three-channel transportable radiometer that operates at 20.6, 31.65, and 90.0 GHz has been developed. The design of the radiometer is described and the results of various experimental applications of the radiometer are presented. The experiments include a comparison of brightness temperature measurements at various frequencies with the water vapor absorption models of Waters (1976) and Lieve (1989). Measurements of absorption ratios for cloud attenuation are given and the radiometer measurements are compared with oxygen absorption calculated using the Rasenkranz (1988) model.

Description: This paper describes a program of airborne radiometric imaging at 90 GHz and 140 GHz. Using high sensitivity (below 1 K) and high angular resolution (0.5-1.0 degree), high quality images have been made. The following measurements are discussed: cloud and fog penetration at 90 GHz, discrimination between agricultural and urban areas, discrimination between different vegetation types, detection of vehicles on roads, detection and classification of airports and airplanes, ship detection and quantitative oil spill sensing. The application of information enhancement techniques with automatic and real time application aspects is also described, and results of applied techniques for contrast and contour enhancement are shown.

Description: Multidecadal time series of surface winds from central tropical Pacific islands are used to compute trends in the trade winds between the end of WWII and 1985. Over this period, averaged over the whole region, there is no statistically significant trend in speed or zonal or meridional wind (or pseudostress). However, there is some tendency, within a few degrees of the equator, toward weakening of the easterlies and increased meridional flow toward the equator. Anomalous conditions subsequent to the 1972-73 ENSO event make a considerable contribution to the long-term trends. The period 1974-80 has been noted previously to have been anomalous, and trends over that period are sharply greater than those over the longer records.

Description: This paper presents an analysis of the uncertainties expected in vertical velocities using a vertically pointing airborne Doppler radar which has a nadir or zenith-pointing beam. To examine the expected uncertainty, the Doppler velocity equation for a moving platform is derived and it is applied to cases of nadir-fixed and stabilized beams. The main emphasis of the paper is on the effect of platform stability on the deduced vertical air motions and it is shown that the antenna must be stabilized to obtain desired accuracy in the vertical velocity measurements.

Description: Mercuric iodide X-ray detectors have been undergoing tests in a prototype scanning electron microscope system being developed for unmanned space flight. The detector program addresses the issues of geometric configuration in the SEM, compact packaging that includes separate thermoelectric coolers for the detector and FET, X-ray transparent hermetic encapsulation and electrical contacts, and a clean vacuum environment.

Description: Monthly fields of shortwave radiation (SR) and latent heat flux (LE) over the central and eastern tropical Pacific between 1980 and 1983 have been computed using satellite data. They are the dominant variable components of surface thermal forcing on the ocean in this time scale. During the 1982-1983 ENSO episode, surface-wind convergence and cloudiness associated with the displacement of equatorial organized convection caused a reduction in both the SR into the ocean and the LE out of the ocean. The lag-correlation coefficients between the forcing (SR-LE) and the sea surface temperature are found to be significantly high outside the equatorial region, showing that surface thermal forcing is the dominant factor in sea surface temperature change. In the narrow equatorial wave guide, ocean dynamics play a more important role, and surface heat flux is a consequence rather than the cause of sea surface temperature change.

Description: An aircraft experiment has been conducted with a dual-frequency (10 GHz and 35 GHz) radar/radiometer system and an 18-GHz radiometer to test various rain-rate retrieval algorithms from space. In the experiment, which took place in the fall of 1988 at the NASA Wallops Flight Facility, VA, both stratiform and convective storms were observed. A ground-based radar and rain gauges were also used to obtain truth data. An external radar calibration is made with rain gauge data, thereby enabling quantitative reflectivity measurements. Comparisons between path attenuations derived from the surface return and from the radar reflectivity profile are made to test the feasibility of a technique to estimate the raindrop size distribution from simultaneous radar and path-attenuation measurements.

Description: Azimuthal response of a scatterometer to radiation scattered by the sea surface was studied in a wind-wave tank. The variation of the normalized radar cross section with the azimuth angle is fitted by a three-term series. Results show that the upwind-downwind asymmetry decreases as the wind speed increases. The crosswind modulation depends on the wind velocity. The results show that the evolution of the long-wind-crosswind ratio evolves with wind speed in a manner similar to the evolution of the isotropy of short capillary-gravity waves. The maximum of the isotropy of the short wind waves is obtained for wind velocities close to 4 m/s. For the same value of the velocity, the variations of radar response between long-wind and crosswind directions is minimum. For lower or higher values of wind velocities the directional accuracy of the radar increases, since the wind-wave field tends to align in the wind direction.

Description: The present interpretation of the radar cross section sigma exp 0 measured by satellite altimeters implies that the rms wave slope gamma is controlled solely by the local wind. However, parameters of wave spectra, including the exponent in the power law for the equilibrium range, depend on sea maturity. The latter is characterized by the nondimensional fetch, x = gX/U-squared. Consequently, gamma and sigma exp 0 are controlled by both U and the wind fetch X. Geosat data for one year are used jointly with in-situ wind and wave observations to assess the fetch-related error trend in altimeter wind speeds. This trend results in overestimated winds in the regions and seasons characterized by a high x, and vice versa. A procedure for wind speed retrieval based on processing sigma exp 0 jointly with the significant wave height information contained in the altimeter wave forms is proposed.

Description: Seasat scatterometer data over the Arabian Sea are used to build wind-stress fields during July and August 1978. They are first compared with 3-day wind analyses from ship data along the Somali coast. Seasat scatterometer specifications of 2-m/s and 20-deg accuracy are fulfilled in almost all cases. The exceptions are for winds stronger than 14 m/s, which are underestimated by the scatterometer by 15 percent. Wind stress is derived from these wind data using a bulk formula with a drag coefficient depending on the wind intensity. A successive-correction objective analysis is used to build the wind-stress field over the Arabian Sea with 2 x 2-deg and 6-day resolution. The final wind-stress fields are not significantly dependent on the objective analysis because of the dense coverage of the scatterometer. The combination of scatterometer and coastal ship data gives the best coverage to resolve monsoon wind structures even close to the coast. The final wind stress fields show wind features consistent with other monthly mean wind stress field. However, a high variability is observed on the 6-day time scale.

Description: Cumulus processes involved in the interaction and merging of clouds under the influence of different imposed conditions (including large-scale lifting forcing, environmental wind shear, and cloud microphysical processes) were studied using simulations with a three-dimensional model. The design of the study was to generate several convective clouds randomly inside the model domain, and then to observe and analyze the interactions and merging between the simulated clouds. Ten merged clouds were identified. Seven of these, each involving two previously separated clouds, generally lie along a line parallel to the initial environmental wind shear vector, while one (also a two-cloud system) lies along a line perpendicular to the wind shear vector prior to merging. The remaining two merging systems involve three parent clouds each; they are a combination of parallel and perpendicular cells. The merging mechanisms associated with three-cloud merging cases are studied by examining the temperature, pressure, and wind fields prior to, during, and following the merging.

Description: The recent development of Scanning Tunneling Microscopy technology allows the application of electron tunneling to position detectors for the first time. The vacuum tunnel junction is one of the most sensitive position detection mechanisms available. It is also compact, simple, and requires little power. A prototype accelerometer based on electron tunneling, and other sensor applications of this promising new technology are described.

Description: The possibility of initiating the growth of ice sheets by solar insolation variations is examined. The study is conducted using a climate model with three different orbital configurations corresponding to 116,000 and 106,000 yr before the present and a modified insolation field with greater reductions in summer insolation at high northern latitudes. Despite the reduced summer and fall insolation, the model fails to maintain snow cover through the summer at locations of suspected ice sheet initiation. The results suggest that there is a discrepancy between the model's response to Milankovitch perturbations and the geophysical evidence of ice sheet initiation. If the model results are correct, the growth of ice shown by geophysical evidence would have occurred in an extremely ablative environment, demanding a complicated strategy.

Description: Thirty-three Landsat TM scenes of California stratocumulus cloud fields were acquired as part of the FIRE Marine Stratocumulus Intensive Field Observations in July 1987. They exhibit a wide variety of stratocumulus structures. Analysis has so far focused upon the July 7 scene, in which aircraft from NASA, NCAR, and the British Meteorological Office repeatedly gathered data across a stratocumulus-fair weather cumulus transition. The aircraft soundings validate the cloud base temperature threshold determined by spatial coherence analysis of the TM thermal band. Brightness variations in the stratocumulus region exhibit a -5/3 power-law decrease of the wavenumber spectra for scales larger than the cloud thickness, about 200 m, changing to a -3 power at smaller scales. Observations by an upward-looking three-channel microwave radiometer on San Nicolas Island also show the -5/3 power-law in total integrated liquid water, suggesting that the largest-scale TM brightness variations are primarily due to variations in the liquid water. The Kolmogorov 5/3 power suggests that for some purposes liquid water in turbulent stratocumulus clouds may be treated as a passive scalar, simply reflecting variations in vertical velocity. This may be tested using the velocities measured by the aircraft.

Description: New nonlinear partial differential equations containing terrain curvature and its rate of change are derived that describe the flow of an atmospheric density current. Unlike the classical hydraulic-type equations for density currents, the new equations are valid for two-dimensional, gradually varied flow over highly curved terrain, hence suitable for computing unsteady (or steady) flows over arbitrary mountain/valley profiles. The model assumes the atmosphere above the density current exerts a known arbitrary variable pressure upon the unknown interface. Later this is specialized to the varying hydrostatic pressure of the atmosphere above. The new equations yield the variable velocity distribution, the interface position, and the pressure distribution that contains a centrifugal component, often significantly larger than its hydrostatic component. These partial differential equations are hyperbolic, and the characteristic equations and characteristic directions are derived. Using these to form a characteristic mesh, a hypothetical unsteady curved-flow problem is calculated, not based upon observed data, merely as an example to illustrate the simplicity of their application to unsteady flows over mountains.

Description: New methods have been developed to implement position sensors based on electron tunneling. The electron tunneling methods enable position to be detected with sub-Angstrom resolution using a compact mechanical structure and simple electronic control elements. A prototype accelerometer is the first sensor based on these principles; it shows reliable operation with a noise-limited sensitivity and a bandwidth of approximately 3 kHz. Based on these results, it is expected that tunnel sensors optimized for many applications will enable an entirely new class of sensors to be developed.

Description: JPL and Aerospace have collected a third set of heavy-ion single-event phenomena (SEP) test data since their last joint IEEE publications in December 1985 and December 1987. Trends in SEP susceptibility (e.g., soft errors and latchup) for state-of-the-art parts are presented. Results of the study indicate that hard technologies and unacceptably soft technologies can be flagged. In some instances, specific tested parts can be taken as candidates for key microprocessors or memories. As always with radiation test data, specific test data for qualified flight parts is recommended for critical applications.

Description: The authors report on an experimental study of dose-induced changes in SEU (single-event-upset) sensitivity of CMOS static RAMs. Two time regimes were investigated following exposure of memories to cobalt-60 gamma rays: the near term, within a few hours after exposure, and the long term, after many days. Samples were irradiated both at room and at liquid nitrogen temperatures. The latter procedure was used in order to freeze in the damage state until SEU measurements could be made prior to annealing. Results show that memories damaged by dose are more sensitive to upsets by heavy ions. The induced changes are substantial: threshold linear energy transfer (LET) values decreased by as much as 46 percent and asymptotic cross sections increased by factors of two to four (unannealed samples).

Description: The spread of charge induced by an ion track in an integrated circuit and its subsequent collection at sensitive nodal junctions can cause multiple-bit errors. The authors have experimentally and analytically investigated this phenomenon using a 256-kb dynamic random-access memory (DRAM). The effects of different charge-transport mechanisms are illustrated, and two classes of ion-track multiple-bit error clusters are identified. It is demonstrated that ion tracks that hit a junction can affect the lateral spread of charge, depending on the nature of the pull-up load on the junction being hit. Ion tracks that do not hit a junction allow the nearly uninhibited lateral spread of charge.

Description: A thorough analysis has been made of electron- and proton- damaged GaAs solar cells suitable for use in space. It is found that, although some electrical parametric data and spectral response data are quite similar, the type of damage due to the two types of radiation is different. An I-V analysis model shows that electrons damage the bulk of the cell and its currents relatively more, while protons damage the junction of the cell and its voltages more. It is suggested that multiple defects due to protons in a strong field region such as a p/n junction cause the greater degradation in cell voltage, whereas the individual point defects in the quasi-neutral minority-carrier-diffusion regions due to electrons cause the greater degradation in cell current and spectral response.

Description: A timing sampler consisting of 14 four-stage inverter-pair chains with different load capacitances was fabricated in 1.6-micron n-well CMOS and irradiated with cobalt-60 at 10 rad(Si)/s. For this CMOS process the measured results indicate that the rising delay increases by about 2.2 ns/Mrad(Si) and the falling delay increase is very small, i.e., less than 300 ps/Mrad(Si). The amount of radiation-induced delay depends on the size of the load capacitance. The maximum value observed for this effect was 5.65 ns/pF-Mrad(Si). Using a sensitivity analysis, the sensitivity of the rising delay to radiation can be explained by a simple timing model and the radiation sensitivity of dc MOSFET parameters. This same approach could not explain the insensitivity of the falling delay to radiation. This may be due to a failure of the timing model and/or trapping effects.

Description: The sources of sub-Saharan precipitation are studied using diagnostic procedures integrated into the code of the GISS climate model. Water vapor evaporating from defined source regions is 'tagged', allowing the determination of the relative contributions of each evaporative source to the simulated July rainfall in the Sahel. Two June-July simulations are studied to compare the moisture sources, moisture convergence patterns and the spatial variations of precipitation for rainy and drought conditions. Results for this case study indicate that patterns of moisture convergence and divergence over northern Africa had a stronger influence on model rainfall over the sub-Sahara than did evaporation rates over the adjacent oceans or moisture advection from ocean to continent. While local continental evaporation contributed significant amounts of water to Sahelian precipitation in the'rainy' simulation, moisture from the Indian Ocean did not precipitate over the Sahel in either case.

Description: The Particle Measuring Systems (PMS) Forwared Scattering Spectrometer Probe (FSSP-100) which was flown on the ER-2 during the Airborne Antarctic Ozone Experiment for the measurement of particles in polar stratospheric clouds has been evaluated and calibrated. The sample volume of the probe per 10-s sampling period increases from 257 cu cm for 1-micron particles to 412 for 15-micron particles, but there is substantial uncertainty in this value. Limitations in the measurements from this instrument and possible corrections are discussed. The uncertainty in the total particle mass measured by the probe may be as large as + or - 100 percent. Recommendations are given for the processing of data from the FSSP used in this project.

Description: The long-term climatic evolution of the earth has been studied on the basis of one-dimensional, globally-averaged climate models yielding only a qualitative understanding of climatic history, and in any case proceeding under a series of potentially invalid assumptions. One such major assumption, which invites comparison with a three-dimensional GCM, is that of fixed relative humidity. A GCM may also be used to study the problem of water loss from both the earth and Venus.

Description: A recent study by Rocketdyne for NASA identified laser anemometry, using a compact optical head, as a feasible diagnostic instrument for the Space Shuttle Main Engine (SSME) Model Verification experiments. Physical Research, Inc. (PRI) is presently under contract from NASA Lewis to develop and deliver such a laser anemometer system. For this application, it is desired to place the laser at a remote distance from the engine, and use single mode polarization preserving fiber optics for the transmission of the laser light to and from the measurement head. Other requirements are given. Analytical and experimental tools are being used to develop the technologies required for the laser anemometer. These include finite element analysis of the optical head and vibration tests for various optical and mechanical components. Design of the optical head and the fiber optic connectors are driven by the temperature and vibration requirements for the measurement environment. Results of the finite element analysis and the vibration tests of the components are included. Conceptual design of the fiber optic launcher and the optical probe has also been complete. Detailed design of the probe as well as the fabrication and assembly of the components is in progress.

Description: An analysis of the relationship between the IMF section boundary crossing, solar flares, the sunspot 11 year cycle variation and the thunderstorm index is given, using the superposition epoch method, for data from more than 13,000 thunderstorms from 10 meteorological stations in the Beijing area and the Northeast region during 1957 to 1978. The results show that for some years a correlation exists between the thunderstorm index and the positive IMF section boundary crossing. The thunderstorm index increases obviously within three days near the crossing and on the seventh day after the crossing. The influence of the crossing on thunderstorms is stronger in the first half year than the latter half year. For different classes of solar flares, the influences are not equally obvious. The solar flares which appeared on the west side, especially in the western region (from 0 to 30 deg) have the most obvious influence. There is no discernible correlation between the thunderstorm index and the sunspot eleven-year cycle.

Description: The possibility that solar variations associated with the 11-year solar cycle may be the cause of the changes in tropospheric weather and climate has been the subject to scientific investigation for several decades. Meteorologists are greatly concerned with the changes in tropospheric phenomena. An attempt was made to find solar activity related changes in tropospheric weather, by the modulation of the quasi-biennial oscillation (QBO) of zonal wind at 50 mb. Rainfall and surface temperature data for a period of about three solar cycles, 1953 to 1988, from various stations in the Indian subcontinent were utilized. By extension, a possible teleconnection was looked for between the temperature changes in middle atmospheric levels and surface temperature when the data are stratified according to east or west phase of the QBO. The temperature data were averaged for January and February to represent the winter temperature and for July and August to represent the summer temperature.

Description: The part of energy of the planetary waves which enters the stratosphere depends on conditions of planetary wave generation and propagation through the tropopause, and the part of planetary wave energy which enters the mesosphere depends on conditions of planetary wave propagation through the stratopause. An attempt is made to estimate connections between extratropical middle atmosphere temperature long term variations and portions of energy of planetary waves which enter the mesosphere and stratosphere during winter seasons in Northern and Southern Hemispheres. Interannual variations of temperatures at the 30 km and 70 km levels are investigated for the central winter months of the period 1970 to 1986. This period includes the descending branch of the 20th solar cycle and the whole 21st cycle. Calculations are made on the basis of measurements at Heiss Island and Molodezhnaya.

Description: The direct modulation of temperature of the mid-latitude mesosphere by the solar-cycle EUV variation, which leads to greater heat input at higher solar activity, is well established. Middle atmosphere temperature modulation by the solar cycle is independently confirmed by the variation of reflection heights of low frequency radio waves in the lower ionosphere, which are regularly monitored over about 30 years. As explained elsewhere in detail, these reflection heights depend on the geometric altitude of a certain isobaric surface (near 80 k), and on the solar ionizing Lyman-alpha radiation flux. Knowing the solar cycle variation of Lyman-alpha how much the measured reflection heights would be lowered with the transition from solar minimum to maximum can be calculated, if the vertical baric structure of the neutral atmosphere would remain unchanged. An discrepancy between expected and observed height change must be explained by an uplifting of the isobaric level from solar minimum to maximum, caused by the temperature rise in the mesosphere. By integrating the solar cycle temperature changes over the height region of the middle atmosphere, and assuming that the lower boundary (tropopause) has no solar cycle variation, the magnitude of this uplifting can be estimated. It is given for the Lidar-derived and for the rocket-measured temperature variations. Comparison suggests that the real amplitude of the solar cycle temperature variation in the mesosphere is underestimated when using the rocket data, but probably overestimated with the Lidar data.

Description: Before the introduction of the Quasi Biennial Oscillation (Q.B.O.) in the study of the solar atmosphere relationship by Labitzke (1987) and Labitzke and Van Loon (1988), the only region of the atmosphere where an effect of a change in solar activity was generally admitted was the mesosphere. The response of the mesosphere, in phase with the solar activity, was found to be about one order of magnitude above model expectancy (around 10 to 20 Kelvin). It was observed independently of the season and maximized around 70 km (Chanin et al. 1987). However, from the same study, it was shown that the response of the stratosphere of opposite sign, clearly seen during winter and autumn, was at the threshold of detection in spring and summer. In the stratosphere, it was shown later that the separation of the data taking into account the sign of the Q.B.O. amplifies the negative correlation of the stratospheric temperature with solar activity in winter; it then becomes more significantly negative for the East phase of the Q.B.O. than when the data are all mixed (Labitzke and Chanin 1988). The studies of the seasonal response of the atmosphere to solar effect is crucial to understand the possible mechanism responsible of such a solar activity Q.B.O. relationship, knowing that the global dynamic circulation is quite different according to the seasons. The question is examined as to whether such separation of the data according to the phase of the Q.B.O. has any impact on the solar response of the middle atmosphere for seasons other than winter.

Description: There is no doubt that the antropogenic effect play an important role in the effects of corpuscular radiation on weather and climate. The task, however, is to distinguish between antropogenic effect in the atmosphere due to human activities and natural climatic fluctuations influencing biological systems. The increase in global temperature during the past 100 years is in relatively good coincidence with the increase in geomagnetic (corpuscular) activity. It is concluded that it could have been the increase in temperature on the Northern Hemisphere, due to the processes occurring in the auroral oval under enhanced corpuscular radiation which led to an increased atmospheric concentration of CO2 in the past. Both processes, i.e., antropogenic and solar activity effects, should be therefore intensively studied due to their important role for elucidating the past and present global change mainly in temperature, climate and biological systems.

Description: Spacecraft range measurements have provided the most accurate tests, to date, of some relativistic gravitational parameters, even though the measurements were made with ranging systems having error budgets of about 10 meters. Technology is now available to allow an improvement of two orders of magnitude in the accuracy of spacecraft ranging. The largest gains in accuracy result from the replacement of unstable analog components with high speed digital circuits having precisely known delays and phase shifts.

Description: EDO Corporation, Barnes Engineering Division designed and constructed a high resolution thermal imaging system on contract to Lockheed for use in the SDI Star Lab. This employs a Pt Si CCD array which is sensitive in the spectral range of 3 to 5 microns. Star Lab will be flown in the Shuttle bay and consists basically of a large, reflecting, tracking telescope with associated sensors and electronics. The thermal imaging system is designed to operate in the focal plane of this telescope. The configuration of the system is illustrated. The telescope provides a collimated beam output which is focussed onto the detector array by a silicon objective lens. The detector array subtends a field of view of 1.6 degrees x 1.22 degrees. A beam switching mirror permits bypassing the large telescope to give a field of 4 degrees x 3 degrees. Two 8 position filter wheels are provided, and background radiation is minimized by Narcissus mirrors. The detector is cooled with a Joule-Thompson cryostat fed from a high pressure supply tank. This was selected instead of a more convenient closed-cycle system because of concern with vibration. The latter may couple into the extremely critical Starlab tracking telescope. The electronics produce a digitized video signal for recording. Offset and responsivity correction factors are stored for all pixels and these corrections are made to the digitized output in real time.

Description: A preliminary evaluation was made by ORNL of a two-color ratio pyrometer (TCRP) for temperature control in the Modular Electromagnetic Levitation (MEL) experiment. A discussion was presented by Eric Spjut at the 1987 NASA Non-Contact Temperature Measurement Workshop (NASA Conf. Publ. 2503, pp. 182-213) in which he described the non-linear characteristics of the time response of TCPs. Researchers replicated his model and results and note that the non-linear response behavior is minimized for small temperature steps at high temperatures. They then used the predicted response in a model for a proportional or integral feedback controller and predicted the control characteristics for heating and cooling a 5-mm diameter sphere of niobium at high (1500 to 2750 K) temperatures. The analysis shows that for a slow (25-ms) time response for a commercial RCRP, overshoots of several hundred kelvins will result from a 100-K decrease in the setpoint, and temperature tracking errors of 14 to 45 K will occur for control temperature ramps of 1000K/s. For a fast (greater than 0.1 ms) time response, the overshoot and ramp response errors are largely eliminated.

Description: The development of a noncontact temperature measurement device utilizing rotating analyzer ellipsometry is described. The technique circumvents the necessity of spectral emissivity estimation by direct measurement concomittant with radiance brightness. Using this approach, the optical properties of electromagnetically levitated liquid metals Cu, Ag, Au, Ni, Pd, Pt, and Zr were measured in situ at four wavelengths and up to 600 K superheat in the liquid. The data suggest an increase in the emissivity of the liquid compared with the incandescent solid. The data also show moderate temperature dependence of the spectral emissivity. A few measurements of the optical properties of undercooled liquid metals were also conducted. The data for both solids and liquids show excellent agreement with available values in the literature for the spectral emissivities as well as the optical constants.

Description: Commercially available types of infrared thermal imaging instruments, both viewers (qualitative) and imagers (quantitative) are discussed. The various scanning methods by which thermal images (thermograms) are generated will be reviewed. The performance parameters (figures of merit) that define the quality of performance of infrared radiation thermometers will be introduced. A discussion of how these parameters are extended and adapted to define the performance of thermal imaging instruments will be provided. Finally, the significance of each of the key performance parameters of thermal imaging instruments will be reviewed and procedures currently used for testing to verify performance will be outlined.

Description: A blocking pattern which formed over eastern North America following the landfall of Hurricane Juan during November 1985 was investigated. It is hypothesize that latent heat released in the Hurricane's rainfall was either directly or indirectly responsible for the large observed 500 mb height rises over eastern Canada during the formation of this block. This idea is evaluated with a diagnostic model for the height tendency field which includes latent heat release as a forcing function. The total column heating is calculated using satellite-derived precipitation estimates. These estimates are qualitatively congruent with observations, but overestimate light rainfall and underestimate heavy rainfall. The calculations reveal that the direct contribution of the heating to the 500 mb height tendency field is small relative to the quasigeostrophic forcing. However, maxima in heating coincide with regions where anticyclonic potential vorticity is generated. Once such region is just upstream of the location of large 500 mb height rises in the incipient block. An indirect role is proposed for the heating in this case. Specifically, anticyclonic potential vorticity is generated near the heating maxima; this vorticity is then advected downstream, forcing the 500 mb heights to rise and the block to develop.

Description: Simple models are being developed to simulate interaction of planetary and synoptic-scale waves incorporating the effects of large-scale topography; eddy heat and momentum fluxes (or nonlinear dynamics); radiative heating/cooling; and latent heat release (precipitation) in synoptic-scale waves. The importance of latent heat release is determined in oceanic storm tracks for temporal variability and time-mean behavior of planetary waves. The model results were compared with available observations of planetary and synoptic-scale wave variability and time-mean circulation. The usefulness of monitoring precipitation in oceanic storm tracks by satellite observing systems was ascertained. The modeling effort includes two different low-order quasi-geostrophic models-time-dependent version and climatological mean version. The modeling also includes a low-order primitive equation model. A time-dependent, multi-level version will be used to validate the two-level Q-G models and examine effects of spherical geometry.

Description: A piecewise linear method of analyzing the effects of discontinuous nonlinearities on control system performance is described. The limit cycle oscillatory behavior of the system resulting from the nonlinearities is described in terms of a sequence of linear system transient responses. The equations are derived which relate the initial and the terminal conditions of successive transients and the boundary conditions imposed by the non-linearities. The method leads to a convenient computation algorithm for prediction of limit cycle characteristics resulting from discontinuous nonlinearities such as friction, deadzones, and hysteresis.

Description: Results of an effort to develop a lower-cost exciter with high stability, low phase noise, and controllable phase and frequency for use in Deep Space Network and Goldstone Solar System Radar applications are discussed. Included is a discussion of the basic concept, test results, plans, and concerns.

Description: The development and implementation of a C-band exciter for use with the Block IV Receiver-Exciter Subsystem at Deep Space Station 14 (DSS-14) has been completed. The exciter supplements the standard capabilities of the Block IV system by providing a drive signal for the C-band transmitter while generating coherent translation frequencies for C-band (5-GHz) to S-band (2.2- to 2.3-GHz) Doppler extraction, C-band to L-band (1.6-GHz) zero delay measurements, and a level calibrated L-band test signal. Exciter functions are described, and a general explanation and description of the C-band uplink controller is presented.

Description: The optimal placement of discrete actuators and sensors is posed as a combinatorial optimization problem. Two examples for truss structures were used for illustration; the first dealt with the optimal placement of passive dampers along existing truss members, and the second dealt with the optimal placement of a combination of a set of actuators and a set of sensors. Except for the simplest problems, an exact solution by enumeration involves a very large number of function evaluations, and is therefore computationally intractable. By contrast, the simulated annealing heuristic involves far fewer evaluations and is best suited for the class of problems considered. As an optimization tool, the effectiveness of the algorithm is enhanced by introducing a number of rules that incorporate knowledge about the physical behavior of the problem. Some of the suggested rules are necessarily problem dependent.

Description: A sensor has been designed and tested for precise pointing applications. The device is able to sense extremely small rotary motion and is immune to cross-axis forces. The hardware and design characteristics of the torque sensor are presented. Test data, integrated control methodology, and future applications are included.

Description: A high torque capacity eddy current damper used as a rate limiting device for a large solar array deployment mechanism is discussed. The eddy current damper eliminates the problems associated with the outgassing or leaking of damping fluids. It also provides performance advantages such as damping torque rates, which are truly linear with respect to input speed, continuous 360 degree operation in both directions of rotation, wide operating temperature range, and the capability of convenient adjustment of damping rates by the user without disassembly or special tools.

Description: The development of a prototype Control Moment Gyroscope (CMG) is discussed. Physical characteristics and the results of functional testing are presented to demonstrate the level of system performance obtained. Particular attention is given to how the man-rated mission requirement influenced the choice of the materials, fabrication, and design details employed. Comparisons are made of the measured system responses against the prediction generated by computer simulation.

Description: The single event effects or phenomena (SEP), which so far have been observed as events falling on one or another of the SE classes: Single Event Upset (SEU), Single Event Latchup (SEL) and Single Event Burnout (SEB), are examined. Single event upset is defined as a lasting, reversible change in the state of a multistable (usually bistable) electronic circuit such as a flip-flop or latch. In a computer memory, SEUs manifest themselves as unexplained bit flips. Since latchup is in general caused by a single event of short duration, the single event part of the SEL term is superfluous. Nevertheless, it is used customarily to differentiate latchup due to a single heavy charged particle striking a sensitive cell from more ordinary kinds of latchup. Single event burnout (SEB) refers usually to total instantaneous failure of a power FET when struck by a single particle, with the device shorting out the power supply. An unforeseen failure of these kinds can be catastrophic to a space mission, and the possibilities are discussed.

Description: Studies are currently underway to further the development of lightweight nickel electrode technology. Work is focused primarily on the space nickel-hydrogen system and nickel-iron system but is also applicable to the nickel-cadmium and nickel-zinc systems. The goal is to reduce electrode weight while maintaining or improving performance thereby increasing electrode energy density. Two basic electrode structures are being investigated. The first is the traditional nickel sponge produced from sintered nickel-carbonyl powder and the second is a new material for this application which consists of a non-woven mat of nickel fiber. Electrodes are being manufactured, tested and evaluated at the electrode and cell level.

Description: Nickel-hydrogen batteries are rapidly becoming accepted for use in low-earth-orbit and geosynchronous orbit applications. With their increased use it has become evident that the storage procedures commonly used for nickel-cadmium cells are not adequate for the nickel-hydrogen system. The capacity loss exhibited by nickel electrodes from various manufacturers when exposed to different storage conditions was determined. A comprehensive test matrix was developed to evaluate capacity loss in nickel electrodes from four different manufacturers. Two types of tests were run; individual electrode tests, which involved flooded capacity and impedance measurements before and after storage under varied conditions of temperature, hydrogen pressure, and electrolyte concentration; and cell tests which primarily evaluated the effects of state-of-charge on storage. The cell tests evaluated capacity loss on cells stored open circuit, shorted and trickle charged at C/100 following a full charge. The results indicate that capacity loss varies with the specific electrode manufacturing process, storage temperature and hydrogen pressure. In general, electrodes stored at low temperatures or low hydrogen pressures exhibited a smaller loss in capacity over the twenty-eight day storage period than those stored at high pressure and high temperature. The capacity loss appears to correlate with the level of cobalt in the nickel electrode, with the most significant loss of capacity occurring in electrodes with higher cobalt levels. Impedance measurements appear to correlate well with the capacity loss observed for a given type of electrode but do not correlate well with the capacity loss between electrodes fabricated by different manufacturers. There was a definite correlation between the electrode potential measured immediately following storage and the measured capacity loss.

Description: Many impedance studies were carried out on Ni electrodes and Ni/Cd and Ni/H batteries. In order for impedance to become a diagnostic tool, accurate and reproducible measurements must be made, and some way of separating the contributions of the individual electrodes must be found. Using the PAR and the Solartron impedance equipment, studies have found that consistent measurements can be made if the cells or electrodes are equilibrated at the voltage of interest. In the charged state, equilibration times required are short, on the order of a few hours or less, but the equilibration time required becomes progessively longer as the voltage is lowered. The cell case can be used as a reference electrode during impedance measurements. The voltage of the case with respect to the electrodes is unimportant provided that it does not change appreciably during the course of the measurement. Measurements were made with several uncycled Ni/Cd cells, one from a lot which was known to have faulty Cd electrodes and another from a lot which showed excellent cycle life and presumably had good Cd electrodes. The impedances of the Ni electrodes vs. the case were similar, while the impedance of the poor Cd electrodes vs. the case. A 50 AH Ni/H cell was also investigated. After subtraction of the ohmic resistances, the sums of the impedances of the individual electrodes were very close to the impedance of the total cell. This indicates that the method is valid for examining the characteristics of the individual electrodes in situ.

Description: A summary of previous Raman spectroscopic results and a discussion of important structural differences in the various phases of active mass and active mass precurors are presented. Raman spectra provide unique signatures for these phases, and allow one to distinguish each phase, even when the compound is amorphous to X-rays (i.e., does not scatter X-rays because of a lack of order and/or small particle size). The structural changes incurred during formation, charge and discharge, cobalt addition, and aging will be discussed and related to electrode properties. Important structural differences include NiO2 layer stacking, nonstoichiometry (especially cation-deficit nonstoichiometry), disorder, dopant content, and water content. The results indicate that optimal nickel active mass is non-close packed and nonstoichiometric. The formation process transforms precursor phases into this structure. Therefore, the precursor disorder, or lack thereof, influences this final active mass structure and the rate of formation. Aging processes induce structural change which is believed to be detrimental. The role of cobalt addition can be appreciated in terms of structures favored or stabilized by the dopant. In recent work, the in situ Raman technique to characterize the critical structural parameters was developed. An in situ method relates structure, electrochemistry, and preparation. In situ Raman spectra of cells during charge and discharge, either during cyclic voltammetry or under constant current conditions were collected. With the structure-preparation knowledge and the in situ Raman tool, it will be possible to define the structure-property-preparation relations in more detail. This instrumentation has application to a variety of electrode systems.

Description: Applications of mesosphere stratosphere troposphere radar to mesoscale meteorology are discussed. The applications include using the radar either as a research tool to improve our understanding of certain dynamical systems or as part of a network used to provide input data for weather forecasting. The workhorse of the operational observing network is the radiosonde balloon which provides measurements of pressure, temperature, humidity, and winds up to heights of 16 to 20 km. Horizontal and vertical measurement capabilities, reflectivity data, derivable quantities and parameters, and special operational requirements are surveyed.

Description: The effect of transient heat flux on heat flux sensor response and calibration is analyzed. A one dimensional case was studied in order to elucidate the key parameters and trends for the problem. It has the added advantage that the solutions to the governing equations can be obtained by analytic means. The analytical results obtained to date indicate that the transient response of a heat flux sensor depends on the thermal boundary conditions, the geometry and the thermal properties of the sensor. In particular it was shown that if the thermal diffusivity of the sensor is small, then the transient behavior must be taken into account.

Description: Measurements of heat flux to space shuttle main engine (SSME) turbine blade surfaces are being made in the Lewis heat flux calibration facility. Surface heat flux information is obtained from transient temperature measurements taken at points within the gauge. A 100-kW Vortek arc lamp is used as a source of thermal radiant energy. Thermoplugs, with diameters of about 0.190 cm and lengths varying from about 0.190 to 0.320 cm, are being investigated. The thermoplug is surrounded on all surfaces except the active surface by a pocket of air located in the circular annulus and under the back cover. Since the thermoplug is insulated, it is assumed that heat is conducted in a one-dimensional manner from the hot active surface to the cooler back side of the thermoplug. It is concluded that the miniature plug-type gauge concept is feasible for measurement of blade surface heat flux. It is suggested that it is important to measure heat flux near the hub on the suction surface and at the throat on SSME blades rotating in engines because stress and heat transfer coefficients are high in this region.

Description: A classification of infrared sensing instruments by type and application, listing commercially available instruments, from single point thermal probes to on-line control sensors, to high speed, high resolution imaging systems is given. A review of performance specifications follows, along with a discussion of typical thermographic display approaches utilized by various imager manufacturers. An update report on new instruments, new display techniques and newly introduced features of existing instruments is given.

Description: The design of a two color pyrometer with infrared optical fiber bundles for collection of the infrared radiation is described. The pyrometer design is engineered to facilitate its use for measurement of the temperature of small, falling samples in a microgravity materials processing experiment using a 100 meter long drop tube. Because the samples are small and move rapidly through the field of view of the pyrometer, the optical power budget of the detection system is severly limited. Strategies for overcoming this limitation are discussed.

Description: A multicolor imaging pyrometer was designed for accurately and precisely measuring the temperature distribution histories of small moving samples. The device projects six different color images of the sample onto a single charge coupled device array that provides an RS-170 video signal to a computerized frame grabber. The computer automatically selects which one of the six images provides useful data, and converts that information to a temperature map. By measuring the temperature of molten aluminum heated in a kiln, a breadboard version of the device was shown to provide high accuracy in difficult measurement situations. It is expected that this pyrometer will ultimately find application in measuring the temperature of materials undergoing radiant heating in a microgravity acoustic levitation furnace.

Description: The use of a gyrotron for space power beaming, especially in the form of a lunar orbiting power station is discussed. The advantages of phased array power beaming, output power, and the design of a quasi-optical gyrotron are discussed.

Description: An understanding is being developed for processes which may be important in the atmosphere, and the definition and analysis of baroclinic experiments utilizing the geophysical fluid flow cells (GFFC) apparatus in microgravity space flights. Included are studies using numerical codes, theoretical models, and terrestrial laboratory experiments. The numerical modeling is performed in three stages: calculation of steady axisymmetric flow, calculation of fastest-growing linear eigenmodes, and nonlinear effects (first, wave-mean flow interactions, then wave-wave interactions). The code can accommodate cylindrical, spherical, or channel geometry. It uses finite differences in the vertical and meridional directions, and is spectral in the azimuthal. The theoretical work was mostly in the area of effects of topography upon the baroclinic instability problem. The laboratory experiments are performed in a cylindrical annulus which has a temperture gradient imposed upon the lower surface and an approximately isothermal outer wall, with the upper and inner surfaces being nominally thermally insulating.