ALBERT

Description: The population balance is an indispensable tool for studying colloidal, aerosol, and, in general, particulate systems. The need to incorporate spatial variation (imposed by flow) to it invokes the reduction of its complexity and degrees of freedom. It has been shown in the past that the method of moments and, in particular, the log-normal approximation can serve this purpose for certain phenomena and mechanisms. However, it is not adequate to treat gravitational deposition. In the present work, the ability of the particular method to treat diffusional and convective diffusional depositions relevant to colloid systems is studied in detail.

Description: A unit cell model is employed to analyze the electrophoresis and electric conduction in a concentrated suspension of spherical charged soft particles (each is a hard core coated with a porous polyelectrolyte layer) in a salt-free medium. The linearized Poisson–Boltzmann equation applicable to a unit cell is solved for the equilibrium electrostatic potential distribution in the liquid solution containing the counterions only surrounding a soft particle. The counterionic continuity equation and modified Stokes/Brinkman equations are solved for the ionic electrochemical potential energy and fluid velocity distributions, respectively. Closed-form formulas for the electrophoretic mobility of the soft particles and effective electric conductivity of the suspension are derived, and the effect of particle interactions on these transport characteristics is interesting and significant. Same as the case in a suspension containing added electrolytes under the Debye–Hückel approximation, the scaled electrophoretic mobility in a salt-free suspension is an increasing function of the fixed charge density of the soft particles and decreases with increases in the core-to-particle radius ratio, ratio of the particle radius to the permeation length in the porous layer, and particle volume fraction, keeping the other parameters unchanged. The normalized effective electric conductivity of the salt-free suspension also increases with an increase in the fixed charge density and with a decrease in the core-to-particle radius ratio, but is not a monotonic function of the particle volume fraction.

Description: The drying of bio-fluid drops results in the formation of complex patterns, which are morphologically and topographically affected by environmental conditions including temperature. We examine the effect of substrate temperatures between 20 °C and 40 °C, on the evaporative dynamics and dried deposits of foetal bovine serum (FBS) drops. The deposits consist of four zones: a peripheral protein ring, a zone of protein structures, a protein gel, and a central crystalline zone. We investigate the link between the evaporative behaviour, final deposit volume, and cracking. Drops dried at higher substrate temperatures in the range of 20 °C to 35 °C produce deposits of lower final volume. We attribute this to a lower water content and a more brittle gel in the deposits formed at higher temperatures. However, the average deposit volume is higher for drops dried at 40 °C compared to drops dried at 35 °C, indicating protein denaturation. Focusing on the protein ring, we show that the ring volume decreases with increasing temperature from 20 °C to 35 °C, whereas the number of cracks increases due to faster water evaporation. Interestingly, for deposits of drops dried at 40 °C, the ring volume increases, but the number of cracks also increases, suggesting an interplay between water evaporation and increasing strain in the deposits due to protein denaturation.

Description: During the past 30 years, more and more 3D-printing techniques based on suspensions with specific rheological properties have been innovated and improved. In this review, principles of dispersing and controlling powders for suspension-based 3D printing are summarized. The suspensions for direct ink writing (DIW) are taken as an example for 3D printing. According to the rheological property requirement of suspensions for direct ink writing, the routes on how its rheological properties can be manipulated are summarized and classified into two categories: I. self-solidification route; II. assistant-solidification route. The perspective on the future of 3D-printing techniques based on suspensions is also discussed.

Description: In this paper, we present the unsteady translational motion of a porous spherical particle in an incompressible viscous fluid. In this case, the modified Navier–Stokes equation with fractional order time derivative is used for conservation of momentum external to the particle whereas modified Brinkman equation with fractional order time derivative is used internal to the particle to govern the fluid flow. Stress jump condition for the tangential stress along with continuity of normal stress and continuity of velocity vectors is used at the porous–liquid interface. The integral Laplace transform technique is employed to solve the governing equations in fluid and porous regions. Numerical inversion code in MATLAB is used to obtain the solution of the problem in the physical domain. Drag force experienced by the particle is obtained. The numerical results have been discussed with the aid of graphs for some specific flows, namely damping oscillation, sine oscillation and sudden motion. Our result shows a significant contribution of the jump coefficient and the fractional order parameter to the drag force.

Description: An oscillating drop rheometer capable of operating under conditions of high pressure and high temperature has been built. The oscillating drop mechanism was able to support pressures as high as 1300 bar and successfully performed oscillations at constant pressure. Apparent elastic and viscous complex moduli were measured for a system of CO2 and synthetic seawater containing 100 ppm of a linear alkyl ethoxylate surfactant for different pressures and temperatures. The moduli had strong dependencies on both pressure and temperature. At temperatures of 40 and 80 °C, the apparent elastic modulus passed through a maximum for pressures between 100 and 300 bar. The harmonic distortion of the oscillations was calculated for all measurements, and it was found that drop oscillations below ca. 2.6 µL caused distortions above 10% due to a mechanical backlash of the motor.

Description: Double emulsions are a promising formulation for encapsulation and targeted release in pharmaceutics, cosmetics and food. An inner water phase is dispersed in an oil phase, which is again emulsified in a second water phase. The encapsulated inner water phase can be released via diffusion or via coalescence, neither of which is desired during storage but might be intended during application. The two interfaces in a double emulsion are stabilized by a hydrophilic and a lipophilic surfactant, to prevent the coalescence of the outer and the inner emulsion, respectively. This study focuses on the influence of the hydrophilic surfactant on the release of inner water or actives encapsulated therein via coalescence of the inner water droplet with the outer O–W2 interface. Since coalescence and diffusion are difficult to distinguish in double emulsions, single-droplet experiments were used to quantify differences in the stability of inner droplets. Different lipophilic (PGPH and PEG-30 dipolyhydroxylstearate) and hydrophilic surfactants (ethoxylates, SDS and polymeric) were used and resulted in huge differences in stability. A drastic decrease in stability was found for some combinations, while other combinations resulted in inner droplets that could withstand coalescence longer. The destabilization effect of some hydrophilic surfactants depended on their concentration, but was still present at very low concentrations. A huge spread of the coalescence time for multiple determinations was observed for all formulations and the necessary statistical analysis is discussed in this work. The measured stabilities of single droplets are in good accordance with the stability of double emulsions for similar surfactant combinations found in literature. Therefore, single droplet experiments are suggested for a fast evaluation of potentially suitable surfactant combinations for future studies on double-emulsion stability.

Description: Driven transport of dilute polymer solutions through porous media has been simulated using a recently proposed novel dissipative particle dynamics method satisfying the no-penetration and no-slip boundary conditions. The porous media is an array of overlapping spherical cavities arranged in a simple cubic lattice. Simulations were performed for linear, ring, and star polymers with 12 arms for two cases with the external force acting on (I) both polymer and solvent beads to model a pressure-driven flow; (II) polymer beads only, similar to electrophoresis. When the external force is in the direction of a principal axis, the extent of change in the polymers’ conformation and their alignment with the driving force is more significant for case I. These effects are most pronounced for linear chains, followed by rings and stars at the same molecular weight. Moreover, the polymer mean velocity is affected by its molecular weight and architecture as well as the direction and strength of the imposed force.

Description: We demonstrate a method for the formation of multilayers composed of reduced graphene oxide (rGO), which can be used for transparent, conducting thin films. Using the layer-by-layer (LbL) assembly of positively and negatively charged GO sheets, we could obtain thin films with highly controllable sheet resistance. The natural negative charge of graphene oxide was turned to positive by the amidation reaction. After forming the multilayer films, the graphene oxide underwent thermal reduction at temperatures above 150 °C. The (rGO+/rGO−) films were characterized by UV-Vis and scanning electron microscopy (SEM), and their conductivity was measured by the four-point method. We found that after deposition of five (rGO+/rGO−), the coating structure reached the percolation limit, and the film resistance decreased more gradually to around 20 kΩ/sq for the films obtained by eleven deposition cycles with graphene oxide reduced at 250 °C. The formation of thin films on polyimide allows the forming of new flexible conductive materials, which can find applications, e.g., in biomedicine as new electroactive, low-cost, disposable sensors.

Description: An analytical study of the electroosmosis and electric conduction of electrolyte solutions in a fibrous medium composed of parallel charge-regulating cylinders with arbitrary electric double layer thickness is presented. A linearized charge regulation model was adopted for the association and dissociation reactions occurring at the amphoteric functional groups over the surfaces of the cylinders, and a unit cell model was employed to accommodate interactions among the cylinders. The electrokinetic equations governing the ionic concentration, electric potential, and liquid flow fields were solved at low zeta potential for the cylinders. Explicit formulas for the electroosmotic mobility and effective electric conductivity in the fiber matrix were obtained. The results indicate that the charge regulation characteristics, such as the equilibrium constants of the reactions occurring at the cylinders’ surfaces and the bulk concentration of the charge-determining ions, influence the surface charge density and potential, electroosmotic mobility, and effective electric conductivity substantially.